Scribd
Upload
81 views7 pages

Computer Application: Stedent Name Ahmed Basim Ahmed

This document appears to be an assignment from a student in their fourth year of civil engineering at the University of Al-ESSRAA. The assignment involves modeling a steel frame structure using StaadPro software, performing structural analysis, designing beams, columns, and slabs, and estimating concrete volumes and reinforcing bar quantities. The student provides details on joint coordinates, member inclinations, element properties, loads, load combinations, design parameters, and analysis steps.

Uploaded by

الزهور لخدمات الانترنيت
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
81 views7 pages

Computer Application: Stedent Name Ahmed Basim Ahmed

This document appears to be an assignment from a student in their fourth year of civil engineering at the University of Al-ESSRAA. The assignment involves modeling a steel frame structure using StaadPro software, performing structural analysis, designing beams, columns, and slabs, and estimating concrete volumes and reinforcing bar quantities. The student provides details on joint coordinates, member inclinations, element properties, loads, load combinations, design parameters, and analysis steps.

Uploaded by

الزهور لخدمات الانترنيت
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Ministry Of Higher Education

University Of Al-ESSRAA
Department Of CIVIL Engineering

Computer Application

Stedent Name
Ahmed Basim Ahmed

Stage Fourth Year

Teacher Name
SARRAA DEYAA

1441--------------------------------------------------------------------------------------------------------2020
Example
According to Staad_Pro V8i software, Plot the geometrical modeling of
the steel frame structure shown below,where (z-1bay 4m).where steel
plate thickness 2.0 cm steel, steel member section (vertical double
W16*36)(horizontal standard MC12*36-in x and z direction),(inclined
double angle L3*3.5*1/4),external col.W16*40

Note: means member in z-direction where

1- D.L. self weight

2- L.L : 2.5 N/m2 plate loads and external loads are shown in the figure.
3- = 1.4 D.L + 1.6 L.L

1
2
Staad space

JOINT COOR

1 000;2 400;3 800;4 030;5 430;6 830;7 060;8 460

9 860;10 0100;11 4100;12 8100

REPALL1 003

MEMBIR INC

1 1 4;2 2 5;3 3 6;4 4 7;5 5 9;6 6 9;7 7 10;8 8 11;9 9 12

10 4 5;11 5 6;12 7 8;13 8 9;14 10 11;15 11 12;16 8 10

17 9 11

REP ALL 1 3 27

ELEMENT INC
35 25 26 27 28; 36 27 28 29 30

SUPPORT
3
1 2 3 13 14 15 FIX

CONSTANTS
E STEEL ALL DEN

DEN STEEL ALL

POI STEEL ALL

ALPHA STEEL ALL

MEM PROP

4 TO 9 22 TO 30 TABLE W16*36
10 TO 15 27 TO 32 TABLE MC12*36
16 TO 17 33 TO 34 TABLE DL3*3.5*0.25
1 TO 3 18 TO 20 TABLE W16*40

ELE PROP
35 36 THIC 0.2

LOAD 1
SELF WEIGHT GY -10

LOAD 2
JOINT LOAD
11 GY -7
12 GY -12

MEM LOAD
3 TRP GX -4 0 3
27 UNI GY -2 0 2

FLOOR LOAD

YR 4 4 FLOAD -2.5 YR

LOAD COMB 3

1 1.4 2 1.6

4
DESIGN BEAMS , COLUMNS AND SLAB , WHERE FY=300 MPA

FC=35 MPA , TIE REIN FOR COLUMNS CLEAR COVER 40 CM TRACK 2

AND ESTIMATE THE VOLUME OF THR CONCRETE AND REIN BARS

PERFORMANCE ANALYSIS

LOAD LIST 3
PRINT LNA RESULTS

UNIT MM NEWTON

START CONCRETE DESIGN

CODE , ACI

CLB 20 ALL

CLS 20 ALL

CLT 20 ALL

FY MAIN 300 ALL


FC 35 ALL

REIN 0 MEM 1 TO 9 18 TO 26

TRACK 2 ALL

DESIGN BEAM 10 TO 15 27 TO 32
DESIGN COL. 1 TO 9 18 TO 26
DESIGN ELE 35 36

CONCRETE TAKE OFF

END CONCRETE DESIGN

FINISH
5
PERFORM ANALYSIS

PRINT ANALYSIS RESULTS


UNIT MMS NEWTON
PARAMETER 1

CODE AA SHTO

FY LD 420 ALL
RATIO 1 ALL

TRACK 2 ALL

CHICK CODE ALL

PARAMETER 2
CODE AASHTO
SELECT OPTIMIZED
PARAMETER 3
CODE AASHTO
STEEL TAKE OFF LIST ALL

FINISH

You might also like