Point Cloud

User's Guide

Version 2014 R1 (10.1)

June 2014

DSP3D-PE-200086F
Copyright
Copyright © 2008-2014 Intergraph® Corporation. All Rights Reserved. Intergraph is part of Hexagon.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains
confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and
international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.
Portions of this software are owned by Spatial Corp. © 1986-2014. All Rights Reserved.
Portions of the user interface copyright 2012-2014 Telerik AD.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was
developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with
subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal
Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the
United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS
252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Intergraph Corporation
300 Intergraph Way
Huntsville, AL 35813

Documentation
Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides,
Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a
particular software product.

Other Documentation
Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support,
SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph
as guidance for using a software product.

Terms of Use
a. Use of a software product and Documentation is subject to the End User License Agreement ("EULA") delivered with the
software product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the
Licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take
precedence and govern the use of this software product and Documentation. Subject to the terms contained within the
applicable license agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the
Documentation as defined in the applicable license agreement and delivered with the software product for Licensee's internal,
non-commercial use. The Documentation may not be printed for resale or redistribution.
b. For use of Documentation or Other Documentation where end user does not receive a EULA or does not have a valid license
agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other
Documentation for Licensee’s internal non-commercial use. Intergraph Corporation gives Licensee permission to print a
reasonable number of copies of Other Documentation for Licensee’s internal, non-commercial. The Other Documentation may
not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and for any
reason by Intergraph Corporation by giving written notice to Licensee.

Disclaimer of Warranties
Except for any express warranties as may be stated in the EULA or separate license or separate terms and conditions, Intergraph
Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability
and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed
a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its
publication date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable
technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.
The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used
or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL
EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

2 Point Cloud User's Guide

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data.
Users should verify for themselves that the data is accurate and suitable for their project work.

Limitation of Damages
IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL,
SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF
REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATION’S LIABILITY EXCEED THE AMOUNT THAT
INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS
MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN
CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2)
YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.
IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS
LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.

Export Controls
Intergraph Corporation’s software products and any third-party Software Products obtained from Intergraph Corporation, its
subsidiaries, or distributors (including any Documentation, Other Documentation or technical data related to these products) are
subject to the export control laws and regulations of the United States. Diversion contrary to U.S. law is prohibited. These Software
Products, and the direct product thereof, must not be exported or re-exported, directly or indirectly (including via remote access)
under the following circumstances:
a. To Cuba, Iran, North Korea, Sudan, or Syria, or any national of these countries.
b. To any person or entity listed on any U.S. government denial list, including but not limited to, the U.S. Department of Commerce
Denied Persons, Entities, and Unverified Lists, http://www.bis.doc.gov/complianceandenforcement/liststocheck.htm, the U.S.
Department of Treasury Specially Designated Nationals List, http://www.treas.gov/offices/enforcement/ofac/, and the U.S.
Department of State Debarred List, http://www.pmddtc.state.gov/compliance/debar.html.
c. To any entity when Licensee knows, or has reason to know, the end use of the Software Product is related to the design,
development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or sensitive
nuclear uses.
d. To any entity when Licensee knows, or has reason to know, that an illegal reshipment will take place.
Any questions regarding export or re-export of these Software Products should be addressed to Intergraph Corporation’s Export
Compliance Department, Huntsville, Alabama 35894, USA.

Trademarks
Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Sketch, SmartMarine, IntelliShip, ISOGEN, SmartSketch,
SPOOLGEN, SupportManager, SupportModeler, Sapphire, and Intergraph Smart are trademarks or registered trademarks of
Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks
of Microsoft Corporation. ACIS is a registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics, Presentation Layer
Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars
Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are trademarks of Infragistics, Inc. Incorporates portions of 2D DCM, 3D DCM, and
HLM by Siemens Product Lifecycle Management Software III (GB) Ltd. All rights reserved. Gigasoft is a registered trademark, and
ProEssentials a trademark of Gigasoft, Inc. VideoSoft and VXFlexGrid are either registered trademarks or trademarks of
ComponentOne LLC 1991-2013, All rights reserved. Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of
Oracle Corporation and/or its affiliates. Tribon is a trademark of AVEVA Group plc. Alma and act/cut are trademarks of the Alma
company. Other brands and product names are trademarks of their respective owners.

Point Cloud User's Guide 3

4 Point Cloud User's Guide
Contents
Preface ................................................................................................................................................... 7
Documentation Set ............................................................................................................................ 7
Documentation Comments............................................................................................................... 10
What's New in Point Clouds ............................................................................................................. 10

Point Clouds......................................................................................................................................... 11

Common Applications ......................................................................................................................... 13

Add Custom Commands .................................................................................................................. 13
Create Filters ................................................................................................................................... 13
Measure Point Cloud and 3D Data ................................................................................................... 13

Project Management ............................................................................................................................ 15

Reference a Point Cloud .................................................................................................................. 15
Remove a Point Cloud Reference .................................................................................................... 15

Interference Checking ......................................................................................................................... 17

Checking Interferences .................................................................................................................... 17
Server-Based Interference Checking (Database Detect) .................................................................. 21
Install Database Interference Detection Service ......................................................................... 23
Configure Interference Service Properties.................................................................................. 23
Start the Database Interference Detection Service ..................................................................... 23
Set IFC Permission Requirements ............................................................................................. 24
Create IFC Permission Group Folder and Permission Group ..................................................... 25
Set IFC Permissions .................................................................................................................. 25
Check Database Interferences................................................................................................... 26
Database Detect Tab (Interference Dialog Box) ............................................................................... 27

Index ..................................................................................................................................................... 29

Point Cloud User's Guide 5

Contents

6 Point Cloud User's Guide

Preface
This document is a user's guide for the Point Cloud functionality of Intergraph SmartTM 3D and
provides command reference information and procedural instructions.

Documentation Set
Intergraph SmartTM 3DDocumentation is available as Adobe PDF files. The content is the same
as the online Help. To access these PDF documents, click Help > Printable Guides in the
software.
The documentation set is divided into four categories:
 Administrative guides contain information about installing, configuring, customizing, and
troubleshooting.
 User's guides provide command reference and how-to information for working in each task.
 Reference data guides define the reference data workbooks. Not all tasks have reference
data.
 ISOGEN guides.

Administrative Guides
Intergraph SmartTM 3D Installation Guide - Provides instructions on installing and configuring the
software.
Project Management User's Guide - Provides instructions for setting up the databases, creating
permission groups, backing up and restoring project data, assigning access permissions to the
model, defining and managing locations for Global Workshare, and version upgrade.
Global Workshare Guide - Provides instructions for setting up the software and the databases to
work in a workshare environment.
Interference Checking Guide - Provides information on installing, configuring, and using the
interference detection service.
Integration Reference Guide - Provides information about installing, configuring, and using
Smart 3D in an integrated environment.
Interpreting Human Piping Specifications - Provides information about how to interpret human
piping specifications so that you can create the corresponding piping specification in the
software.
Design and Data Exchange with PDMS - Provides information about how to export model data
from Smart 3D to PDMS and from PDMS to Smart 3D. Specific guidelines relating to best
practices and known limitations of the export functionality are also included.
Export to Plant Design System (PDS) User's Guide - Provides information about how to export
model data from Smart 3D to PDS. Specific guidelines relating to best practices and known
limitations of the export functionality are also included.
Point Cloud Reference - Provides information for referencing point cloud files provided by point
cloud vendors in Smart 3D.

Point Cloud User's Guide 7

Preface

Troubleshooting Reference Guide - Provides information on how to resolve errors that you might
encounter in the software by documenting troubleshooting tips, error messages, and To Do List
messages.
Plant Design System (PDS) Guide - Provides all information needed to use PDS with Smart 3D.
Topics include referencing active PDS projects in Smart 3D, exporting PDS data and importing
that data into Smart 3D, and converting PDS reference data to Smart 3D reference data.
Intergraph SmartTM 3D Programmer's Guide - Provides information about custom commands,
naming rules, and symbol programming. If you install the Programming Resources, this
document is delivered to the [Product Folder]\Programming\Help folder.

User's Guides
Catalog User's Guide - Provides information about viewing, editing, and creating reference data
and select lists (codelists).
Civil User's Guide - Provides information about routing trench runs in the model.
Common User's Guide - Provides information about defining workspaces, manipulating views,
and running reports.
Compartmentation User's Guide - Provides instruction for placing volume objects such as
compartments and zones in the model.
Electrical User's Guide - Provides information about routing electrical cable, cableway, cable
tray, and conduit.
Equipment and Furnishings User's Guide - Provides information about placing equipment.
Geometry Analysis and Repair User's Guide - Provides instructions for importing and exporting
model data, checking the data against a defined set of requirements, and repairing the data.
Grids User's Guide - Provides instructions for creating coordinate systems, elevation grid
planes, vertical grid planes, radial cylinders, radial planes, grid arcs, and grid lines.
Hangers and Supports User's Guide - Provides instructions on placing piping, duct, and
cableway supports in the model.
Hole Management User's Guide - Provides instructions for placing, reviewing, and approving
holes in a structure.
HVAC User's Guide - Provides instructions for routing HVAC duct.
Molded Forms User's Guide - Provides instructions for placing hull, bulkheads, major openings,
stiffeners, and other major structural components in the model.
Orthographic Drawings User's Guide - Provides information about creating and managing
orthographic drawings.
Piping Isometric Drawings User's Guide - Provides information about creating and managing
piping isometric drawings.
Piping User's Guide - Provides instructions for routing pipe and placing valves, taps, and pipe
joints.
Planning User's Guide - Provides instructions about defining the assembly hierarchy (production
bill of material) by creating blocks and assemblies and by specifying the assembly sequence.
Reports User's Guide - Provides information about creating and managing spreadsheet reports.

8 Point Cloud User's Guide

 Preface

Space Management User's Guide - Provides instructions for placing space objects such as
areas, zones, interference volumes, and drawing volumes in the model.
Structural Analysis User's Guide - Provides instructions for defining loads, load cases, load
combinations, and the importing and exporting of analytical data.
Structural Detailing User's Guide - Provides instructions for creating, detailing, and maintaining
the structural members of a model.
Structural Manufacturing User's Guide - Provides instructions for creating and maintaining
manufacturing objects such as templates, jigs, and margins.
Structure User's Guide - Provides instructions for placing structural members, such as beams,
columns, slabs, openings, stairs, ladders, equipment foundations, and handrails.
Systems and Specifications User's Guide - Provides instructions for creating systems and
selecting the available specifications for each system type.

Reference Data Guides

2D Symbols User's Guide - Provides command reference information and procedural
instructions for creating 2D symbols used to represent collars, clips, profiles, brackets, and other
items.
2D Symbols Reference Data Guide - Provides information about the two-dimensional symbols
used in all tasks.
Civil Reference Data Guide - Provides information about trench straight features, turn features,
reference data.
Compartmentation Reference Data Guide - Provides information about compartmentation
reference data.
Drawings and Reports Reference Data Guide - Provides information about reports reference
data.
Electrical Reference Data Guide - Provides information about electrical cable, cableway, cable
tray, and conduit reference data.
Electrical 3D Symbols Reference - Provides information about the cable tray and conduit 3D
symbols that are available.
Equipment and Furnishings Reference Data Guide - Provides information about equipment
reference data.
Equipment 3D Symbols Reference - Provides information about the equipment, equipment
component, design shapes, and design aides 3D symbols that are available.
Hangers and Supports Reference Data Guide - Provides information about hangers and
supports reference data.
Hangers and Supports 3D Symbols Reference - Provides information about the hanger and
support 3D symbols that are available.
Hangers and Supports SmartPart Symbols Reference - Provides information about the hanger
and support SmartPart symbols that are available.
Hole Management Reference Data Guide - Provides information about hole reference data.
HVAC Reference Data Guide - Provides information about HVAC reference data.

Point Cloud User's Guide 9

Preface

HVAC 3D Symbols Reference - Provides information about the HVAC 3D symbols that are
available.
Reference Data Guide - Provides instructions about the Bulkload utility, codelists, and the
reference data common to several disciplines.
Piping Reference Data Guide - Provides information about piping reference data including piping
specifications, piping specification rules, piping parts, and piping symbols.
Piping 3D Symbols Reference - Provides information about the piping 3D symbols that are
available.
Space Management Reference Data Guide - Provides information about space management
reference data.
Structure Reference Data Guide - Provides information about structural reference data.
Structure 3D Symbols Reference - Provides information about the stair, ladder, footings, and
equipment foundation 3D symbols that are available.
Structural Reference Data Overview - Provides an overview of the marine mode structural
reference data library.

ISOGEN Guides
Symbol Keys Reference Guide - Provides information about the symbol keys for isometric
drawings. This guide is from Alias, the makers of ISOGEN.

Documentation Comments
We welcome comments or suggestions about this documentation. You can send us an email at:
[email protected].
Documentation updates for supported software versions are available from
https://smartsupport.intergraph.com (https://smartsupport.intergraph.com).

What's New in Point Clouds

The following changes have been made to the Point Cloud User's Guide.
Version 2014 R1 (10.1)
 No changes have been made to this document for this release of the software.
 Cloudworx is now licensed through Intergraph using SPLM and can be purchased directly
from Intergraph. Leica licensed versions can still be used.

10 Point Cloud User's Guide

SECTION 1
Point Clouds
Point clouds are created by 3D laser scanners. These devices measure a large number of
points on the surface of an object, and output a point cloud as a data file. The point cloud
represents the visible surface of the object that has been scanned or digitized.
Smart 3D provides vendor-neutral point cloud data integration within the Model modeling
software environment. Using point clouds saves redrawing an object, while still being able to
add to it or build on top of it.
The following picture shows a point cloud and Smart 3D design objects. The Workspace
Explorer shows the Laser Point Cloud along with other design objects. The toolbar includes a
new menu, Accessories (or Cloudworx when using Leica), that contains options from the
third-party point cloud vendor.

Point Cloud User's Guide 11

Point Clouds

Point Cloud Vendors

Smart 3D provides support for the point cloud vendors Trimble, Leica Geosystems, Quantapoint,
and Z+F UK, however, only Leica Geosystems Cloudworx has been certified on Smart 3D 2014.
All vendors provide interface software that allows existing conditions captured with laser
scanners to be viewed in the design environment. Follow the directions in the point cloud vendor
documentation for using their point cloud functionality.
All clients referencing Z+F Point Cloud data need to turn off the Smart 3D hardware with
the CoreDisplaySettings.ini file.

Accessing Point Cloud

The third-party software that provides the point cloud data, adds an Accessories (or
Cloudworx) menu to the Smart 3D menus. From the Accessories (or Cloudworx) menu you
can open the point cloud. You can also locate the point cloud in the filters.

Selecting a Data Point

To select a particular point in the cloud, press and hold the CTRL+SHIFT keys and click the
data point.(Point selection, especially for measurements, should only be done in orthographic
mode, not in Perspective.)

Measuring
You can measure point-to-point within the cloud and cloud point-to-3D object. Select Tools >
Measure, or click on the toolbar.

Interference Checking (IFC)

You can use IFC on the local database to ensure the additions to the point cloud are good.
Select Tools > Check Interference.

12 Point Cloud User's Guide

SECTION 2
Common Applications
Point cloud vendors add custom commands to the Accessories menu. When a point cloud is
added to a Model through Project Management, the Accessories menu becomes active and
you can use the provided commands. Each vendor has developed their own menus. Leica's
menu is called Cloudworx instead of Accessories.
For example, the ability to modify the point cloud density or the colors of the points is a feature
that is exposed by the vendors.

Add Custom Commands

When a point cloud reference is added to a Model through Project Management, point cloud
vendors add custom commands to Common.
Point cloud vendor XML files add custom commands, for example, modifying cloud density or
changing the point colors. The Accessories menu lists those commands.

Create Filters
If the third-party point cloud vendor software has been installed and registered, you can select
point clouds using the Filter Properties dialog box. From the System or Object Type tab, you
can select the point cloud only or the point cloud system.

Measure Point Cloud and 3D Data

You measure the surface distance between two point cloud data points, or one point cloud data
point and a 3D point, just as you measure any other distances.

 When measuring a distance, you must click two selection points to define the distance to be
measured. Measuring should only be done in Orthographic mode, not Perspective.
 Simple measurements are on the toolbar. Click Tools > Measure to open other
measurement modes.
 The distances display in the Text view.

Point Cloud User's Guide 13

Common Applications

14 Point Cloud User's Guide

SECTION 3
Project Management
The Project Management interface displays a hierarchical view of a model, including satellite
locations, databases, permission group folders, and permission groups. You use the Project
Management interface to select the point cloud model that is provided by a third-party point
cloud application.
After you install the third-party point cloud software, you add the new point cloud model to
Project Management by right-clicking in the interface and selecting New Point Cloud Model
Reference. This command, and others relating to point clouds, are only visible when the
third-party applications have been registered and are integrated with the software.
After you select the point cloud model, open Smart 3D and begin adding to the model.

Reference a Point Cloud

1. From the tree view hierarchy in the left pane, right-click the Model icon, and then select New
Point Cloud Model Reference.
2. In the Point Cloud Model Reference dialog box, select a vendor from the Select Point
Cloud vendor to use list. Only one vendor can be referenced at a time.
The vendor software might prompt you to type details for the point cloud reference. These
details vary as the point cloud configuration file is supplied by each vendor. Follow the vendor
prompts as directed.
When defining the workspace, the point cloud appears on the New Filter Properties dialog box
on both the System tab and Object Type tab. When the point cloud is defined, it appears in
Smart 3D on the Workspace Explorer view. Vendor-specific commands appear on the
Accessories menu.

Remove a Point Cloud Reference

1. From the tree view hierarchy in the left pane, right-click the Model icon, and then select New
Point Cloud Model Reference.
2. In the Point Cloud Model Reference dialog box, select None from the Select Point Cloud
vendor to use list, and then click OK.

Point Cloud User's Guide 15

Project Management

16 Point Cloud User's Guide

SECTION 4
Interference Checking
Point clouds provide a new reference data type available through Smart 3D. Interference
checking (IFC) supports the creation of interference checks between Smart 3D data and point
cloud data.
IFC processes the contents of a model database by querying the objects based on their
LastModified timestamp. When IFC starts processing, it queries objects using two time
windows, one towards the future and one towards the beginning of time; that is, the time stamp
of the first object in the model.
This process uses a query window whose time request varies from a couple of minutes to an
hour. The search towards the future has a lag of a few minutes, such that areas with current
edits happening are not looked at until some time has passed and the edits have settled.
Point Cloud data is considered reference data, similar to PDS and MicroStation reference files.
For PDS and MicroStation reference files, IFC queries for changes every so often, asking if
anything has changed since the last time the reference file was queried for changes. However,
point cloud processing is different. With point cloud interference checking enabled, as each
object from a time window is processed, it is also processed against the point cloud data to
ensure that new objects are properly placed.

Checking Interferences
Interference checking (IFC) ensures that parts do not occupy the same volumetric space and
that each part meets the design criteria for clearance. A successful interference check ensures
that there is sufficient space around the parts so that they can operate properly, be serviced
properly, and be easily installed or removed when necessary. The IFC process can look at all
model data, including data from a referenced 3D model, a referenced PDS project (32-bit only),
referenced MicroStation and 3D AutoCAD files, and Point Clouds from third-party software with
valid connections.
There are two methods for interference checking:
 Server-based interference checking called Database Detect. For more information, see
Server-Based Interference Checking (Database Detect) (on page 21).
 Interactive interference checking called Local Detect. For more information, see Interactive
Interference Checking (Local Detect) in the Interference Checking Guide, available from the
Help > Printable Guides command in the software.
The major differences between the two methods are:

Database Detect Local Detect

Runs continuously (System Administrator Works only within the current session
choice)

A dedicated server takes care of the IFC Provides immediate graphical feedback (works

Point Cloud User's Guide 17

Interference Checking
process, minimizing impact on users and immediately after commit.)
improving performance

Creates persistent interferences that are Creates temporary interference markers in a

stored in the Model database user session, which are not stored in the Model
database. After you refresh the workspace, the
temporary markers are removed

Based on administrator settings (controlled Based on individual user settings

by permission groups)

Provides feedback on how much has been Checks only created and modified objects in a
checked in the entire plant model session

Interference markers associate and come Clears dynamic interferences after refreshing
into the workspace along with the object workspace
participating in the interference

The SP3D-Foreign Interferences Finds interferences involving referenced 3D

option only checks Smart 3D objects against models, PDS objects, referenced MicroStation
foreign objects. objects, and 3D AutoCAD files in the
workspace without requiring a specific setting
SP3D-Foreign Interferences does not
check for interferences between two foreign
objects.
SP3D-PointCloud Interferences option only
checks objects against point clouds and
Smart 3D.

Includes a referenced point cloud when the Receives the point cloud specification via the
Smart 3D Point Cloud Compare option is File > Define Workspace workflow in Smart
selected in the Project Management 3D when the Smart 3D Point Cloud Compare
interference checking settings. option is selected.

The Database interference checking objects, or markers, appear in the model until other objects
are moved so the interferences no longer exist, or the aspects for the interference process are
changed. It is not possible to delete an interference object in the same way you can delete other
objects in the model. However, you can tailor the display to hide acceptable interferences.

18 Point Cloud User's Guide

 Interference Checking
How Interference Checking Results Appear
The Database Detect process marks any persistent interference with a spherical interference
mark at the location of the interference. For example, the Database Detect service found an
interference between this floor slab and this column, so it placed a spherical interference marker
at that location.

The Local Detect process marks any interference it finds with a cube interference marker. For
example, the software finds an interference and places a cube interference marker where there
is an interference between a pipe and the floor.

For both processes, the color of the marker indicates the type of the interference: red for severe,
green for clearance, and yellow for optional. You can modify the default interference marker
colors with the Format > Surface Style Rules command. You can change the size of both the
Database Detect and Local Detect interference markers using the Marker size option on the
Interference Server Setting dialog box in Project Management task and the Interference
Checking Settings dialog box in the Common task, respectively.
You can clear the acceptable interferences from your workspace by changing the required
action on the Interference List Dialog Box, and then editing the display properties on the
Interference Checking Settings Dialog Box.
In general, the software checks the parts involved in interfering objects to find and report the
interferences. For example, if you have a pipe run that consists of a pipe, an elbow, and a pipe,

Point Cloud User's Guide 19

Interference Checking
each intersecting another pipe. The interfering pipe intersects the pipe run at each of the three
positions. The software generates three interferences, and then displays them in the
Interference List dialog box.
If an object has an interference with two other objects, these interferences are listed as two
separate interferences in the Interference List. You can view all possible associated
interferences (selected aspects) of an interference by right-clicking the interference row in the
List view. This action opens the Interference Settings dialog box, and you can then click Other
Aspects to see a list of all the aspects at the interfering location.
When an object is brought into the workspace, all of its associated interferences appear,
even if they are not part of the filter used to define the workspace.

Role of the Administrator

An Administrator can limit the access to interference checking to the proper permission groups.
An Administrator sets up the options for the background interference checking at the beginning
of the project and is the only one permitted to change these options. This capability requires that
an Administrator have read access to all objects in the database for the background interference
checking to work properly. Users do not need to have access to all objects. For more
information, see the Smart 3D Interference Checking Guide available from the Help > Printable
Guides command in the software.
The server-based interference checking process can only be started from a client machine on
which both the Project Management and the Database Interference Detection Process
options are installed. The Administrator can run the detection process on more than one model
simultaneously on the interference server. When an Administrator starts Database Detect,
progress and statistical information is displayed on the Status tab of the dialog box.
Only an Administrator can start the Interference Detection Service (IfcNtSvc) on the
system and set up the Interference Detection process (IFCProcess).

Interference Checking License Management

The interference checking process consumes one license to process five models. It releases a
license for every five models that stop processing. For example, IFC consumes two licenses to
process ten models, one license for processing Model1 through Model5, and then another for
processing Model6 through Model10. Similarly, it releases a license after the sixth model stops
processing, and then another after the remaining models stop processing.

 The IFC service does not consume a license when it starts. It consumes a license only while
processing the model.
 IFC consumes a license for every five models.
 IFC cannot process a new model if a new license is not available.
 If IFC fails to consume or release a license, the software logs error messages in the error
log and in the Event Viewer Application log with the source name IfcNtSvc.
 You cannot set a number for processing models in the registry.

20 Point Cloud User's Guide

 Interference Checking

Server-Based Interference Checking (Database

Detect)
Unlike the traditional file-based method of manually defining groups of parts to check against
each other, Check Interference is a separate software process that runs directly on the Model
database. Although the interference detection process can be run on any computer with the
Database Interference Detection Service installed, due to the intensive nature of the
interference check computations, the recommendation is to have a computer dedicated as the
interference server.
In order to monitor interferences, you must install the Database Interference Detection
Service option on the same computer that the Project Management option is installed.

Database detection options are set in the Project Management task. You can also start and stop
the interference detection service in the Project Management task.
Interference detection requires disk space for the file cache that temporarily stores the
interference data. Before starting the interference process, the interference server checks to see
if enough space exists in the TMP location for the file cache. The server also checks to see if
you have the proper permissions to write, read, and delete files in the TMP location. During the
process, if the space becomes too low, the software stops IFC, and then displays an error
message. These checks primarily apply to the server-based interference process. Although,
they can apply to the local checking process if extremely low or no disk space is available for the
temporary folder on the local computer.
Configure automatic disk defragmentation in order to free space for the file cache.
After you start the process, use the Status tab on the Interference Server Settings dialog box
to monitor the start time, progress of the interference checking, time when the last part was

Point Cloud User's Guide 21

Interference Checking
modified, and the status of the checking. A box at the top of the dialog box identifies the model
that you are checking.
The software automatically checks new or modified objects apart from existing objects. When
you create or modify an object, the software checks for interference against all objects in the
Model database. The interferences generated by this process are persistent; that is, the
interferences are stored in the database like any other objects in the software. You can also
modify these objects by changing the properties. Interferences are also assigned to a
permission group; thereby the entire process is under the control and restrictions of an
administrator.
You can interrupt the automatic interference checking process during a work session without
forcing a recheck of all parts in the database when the process is brought back online. When
you restart the interference check process, the software begins checking where it left off when
the process went offline. However, if you change any of the options on the Interference Server
Settings dialog box for Database Detect, all pre-existing interference checking processes are
cleared from the database, and checking restarts from the beginning.
The server-based interference checking runs continuously. Therefore, you can perform an
interference check at any time and view the interferences of interest that result from the
background check by refreshing the workspace. After you have reviewed the interferences, you
can remove an interference automatically from the database by editing the objects so that the
interference no longer exists. You can then see the results of your edit by refreshing the
workspace. Because certain types of interferences are allowable, you also have the capability to
mark such interferences as acceptable.
Be aware that there is a four minute interval between the time you make your edits and the time
that the database detect service rechecks the objects. After the database detect process
reaches 100%, the software issues a query only every two minutes to locate newly modified
objects. Therefore, it is possible that there is a six minute delay before a modified object is
processed. We do not recommend changing the default four minute interval. However, if you are
in Project Management with the Interference Server Setting dialog box open, press
CTRL+SHIFT+F12 to change the default four minute interval.
When the Database Detect process reaches 100%, it does not mean that all clashes between
Smart 3D and other foreign objects, such as PDS, referenced MicroStation objects, 3D
AutoCAD files, or referenced point cloud objects, have been processed. Here, 100% indicates
that all Smart 3D objects have been processed against each other.
You must run the Database Detect process before running an interference report. The
report is not intended to run on local interferences.

What do you want to do?

 Install Database Interference Detection Service (on page 23)
 Configure Interference Service Properties (on page 23)
 Start the Database Interference Detection Service (on page 23)
 Set IFC Permission Requirements (on page 24)
 Create IFC Permission Group Folder and Permission Group (on page 25)
 Set IFC Permissions (on page 25)
 Check Database Interferences (on page 26)

22 Point Cloud User's Guide

 Interference Checking

Install Database Interference Detection Service

Prior to installing the Database Interference Detection Service on a computer, verify that all
prerequisite software has been installed. If you have an older version of the Database
Interference Detection Service installed on your computer, remove it before loading the new
software.
You must have administrator privileges on the computer to install the software.
1. Open Control Panel.
2. Open Programs and Features.
3. Select Intergraph Smart 3D from the list of installed software's.
4. Click Change.
5. Select Database Interference Detection Service.
6. Optionally, select 64-bit Services if you want to install the 64-bit version of the interference
detection service also.
If you are running Oracle, you must install the 64-bit Oracle client on the
computer running 64-bit interference detection.
7. Click Update.
If you have not yet installed Smart 3D on the computer, see Install Smart 3D Client
Software in the installation guide for detailed instructions.
If you plan to check interferences with a referenced PDS® project, you must install and configure
the PDS Data Access component (with all prerequisites) on the IFC database detection server.
For more information, see the Plant Design System (PDS) Guide.

Configure Interference Service Properties

1. Click Start > All Programs > Intergraph Smart 3D > Database Tools > Configure
Interference Checking Service.
2. In the Configure Interference Service dialog box, select your database type.
3. Select the site database server (Microsoft SQL Server) or the Oracle Service for the site
database.
4. Select the site database on which the interference service is to run.
5. Click OK.

Start the Database Interference Detection Service

Prior to starting the Database Interference Detection Service, you must configure its properties.
For more information, see Configure Interference Service Properties (on page 23).
1. Log on with Administrative privileges to the computer on which the Project Management
and Database Interference Detection Service options are installed.
2. Open the Control Panel, and then double-click Administrative Tools.
3. In the Administrative Tools window, double-click Services.

Point Cloud User's Guide 23

Interference Checking
4. Right-click either the Smart 3D Interference Detection Service or the Smart 3D
Interference Detection Service 64-bit, and then select Properties from the shortcut menu.
The 64-bit Smart 3D Interference Detection Service does not process PDS
attachments or Point Clouds. Use Reference 3D for PDS Projects if you are running 64-bit
IFC, or you can switch to a 32-bit IFC server to process PDS attachments and supported
Point Clouds.
5. On the Log On tab, select the This account option, and then type the user name that has
Administrative privileges.
This version of the software does not support the Local System account option.
6. In the Password and Confirm password boxes, type the password for the user account.
7. On the Recovery tab, set the options as required.
8. On the General tab, verify that the Startup type is set to Automatic.
9. In the Service status section, click Start.
10. Click OK.

 The interference checking service does not consume a license when it starts. It consumes a
license only while processing the model. For more information, see Checking Interferences.
 If clashes between the point cloud and the Smart 3D objects are selected to check for
interferences, then Smart 3D Interference Detection Service or Smart 3D Interference
Detection Service 64-bit should be started from the command prompt. From the command
prompt, navigate to install\Foul Check\Middle\bin, and then type IFCNtSvc.exe /Auto/0,
and press ENTER.
 Errors that are encountered during startup of the Database Interference Detection service
are logged to the Event Viewer Application Log with the source name IfcNtSvc.
 Do not run the 32-bit and 64-bit interference detection services simultaneously on a
computer. IFC must only run as a single instance for the entire model.

Set IFC Permission Requirements

You must install the Database Interference Detection Service option in order to monitor
interferences. For more information about installing and configuring this service, see the Smart
3D Installation Guide available from Help > Printable Guides.
The user account running the IFC Windows service must have at least Read access
to the SharedContent folder. Otherwise, IFC generates a bad part marker with clashes against
structural fireproofing.
A Smart 3D Interference Detection Service icon is placed under the Model node in the Project
Management tree. After the proper access permissions are configured, you can start and stop
the Database Detect process from any computer on which the Project Management option is
installed.
The Smart 3D database hierarchy is comprised of a Model configuration that consists of the
Model and Catalog databases. For the IFC Database Detection process to run correctly,
permissions must be set on the Model and Model permission groups according to the following
guidelines:

24 Point Cloud User's Guide

 Interference Checking
Log on privileges for the IFC Administrator include:
 Read access on the Model (Model database) at a minimum
 Full Control permissions or access on a minimum of one permission group
In the Project Management task, create a new permission group folder and permission
group under the Plant icon to store the IFC results. For example, type IFC Permission
Group Folder and IFC Permission Group in the New Permission Group Folder and New
Permission Group dialog boxes, respectively. For more information, refer to Create IFC
Permission Group Folder and Permission Group (on page 25).
 Read access on all other Model (Model database) permission groups at a minimum.

Create IFC Permission Group Folder and Permission Group

1. Log on with administrative privileges to the computer where you have installed the Project
Management and Database Interference Detection Service options.
2. In the Project Management tree view, navigate to the Models icon.
3. Expand the Models folder.
4. Right-click a Model under the Models folder, and select New Permission Group Folder on
the shortcut menu.
5. Type IFC Permission Group Folder for the name of the new permission group folder.
6. Click OK to close the New Permission Group Folder dialog box.
7. In the tree view, navigate to the IFC Permission Group Folder icon.
8. Right-click the IFC Permission Group Folder, and select New Permission Group on the
shortcut menu.
9. Type IFC Permission Group for the name of the new permission group.
10. Click OK to close the New Permission Group dialog box.
After the IFC permission group is created, you must assign the proper access
permissions. For more information, see Set IFC Permissions (on page 25).

Set IFC Permissions

1. Log on with administrative privileges to the computer on which the Project Management
and Database Interference Detection Service options are installed.
2. In the Project Management tree, navigate to the IFC Permission Group icon.
3. Right-click the IFC Permission Group icon, and select Permissions.
4. On the Access Permissions dialog box, click Add.
5. In the Add names grid, double-click in the User cell, type the domain and name of the user
or group to add.

 You can also click Add and search for users using the Select Users and Groups
dialog box. This is a common Windows dialog box. For information regarding the
options in this dialog box, see your Windows documentation.

Point Cloud User's Guide 25

Interference Checking
 To remove a user or group from the Add names grid, select the appropriate row, and
then click Remove.
6. In the Type of access list, select the type of access you want to assign. The software
automatically updates the associated row in the Add names grid.
7. Click OK.
8. Click OK again to close the Access Permissions dialog box.

Check Database Interferences

Before performing the following procedure, you must first manually configure the SmartPlant 3D
Interference Detection Service on the computer with the service installed.
1. In the Project Management tree, right-click the Interference Server icon under the
Model for which you want to start Database Detect. Then select Properties on the shortcut
menu.
2. In the Interference Server Settings dialog box, assign interference checking priorities to
aspects.
Maintenance, for example, is a typical aspect listed in the Aspect column. If a check
of this aspect is important, you can indicate the priority as Required. If Maintenance is low
priority or not important, you can indicate the priority as Optional or Not Checked.
3. Specify the interference comparison criteria:
 Required - Required - Defines interferences classified as hard/hard. For example, one
pipe physically intersects with another pipe. Severe interferences are shown in red.
 Required - Optional - Defines interferences that are not as severe and are classified as
hard/soft. For example, one pipe overlaps the optional aspect of the other object.
Optional interferences are shown in yellow.
 Optional - Optional - Defines interferences that are not severe and are classified as
soft/soft. For example, the maintenance aspect of one piece of equipment overlaps the
maintenance aspect of another. Optional interferences are shown in yellow.
 Smart 3D - Foreign Interferences - Considers objects outside the active model for
interferences. For Local Detect, this option is enabled by default. For Database Detect,
this box must be checked if you want referenced 3D models, referenced PDS objects,
referenced MicroStation objects, and 3D AutoCAD files to be considered. This option
only checks objects against foreign objects. It does not check for interferences between
two foreign objects.
 Smart 3D - Point Cloud - Considers Smart 3D objects and point cloud objects for
interferences. For Database Detect, this option must be selected to consider Smart 3D
objects and point cloud objects. For Local Detect, select the Smart 3D Point Cloud
check box to consider local interferences. The point cloud must have a valid connection
to the model with no unresolved vendor licensing issues for this check box to be
available.
4. In the Include clearance list, select the needed clearance rule. Clearance interferences are
shown in green.
5. From the Assign results to permission group box, choose the permission group to which
all the detected interferences are assigned.

26 Point Cloud User's Guide

 Interference Checking
6. In the Marker size field, type the value for the size of the interference symbols that generate
in the model.
Choose a marker size that is clearly readable, but one that does not interfere with the
smaller details in the workspace view.
7. Click Start on the Database Detect tab. After you click Start, the Status tab on the
Interference Server Settings dialog box displays the progress of the processing for parts
that existed previously and for new or changed parts during the run.
If the IFC Server detects that your system resources are too low (due to a
significant process requiring the majority of system memory), then the IFC process stops and
displays a message box notifying you that the service has stopped for this reason.

 The Smart 3D Interference Detection service does not consume a license when it starts. It
consumes a license only while processing the model. For more information, see
 To start the server interference detection process, you must have at least Read access to all
objects in the model and Write access to the model itself. Access privileges are assigned for
each permission group in the Project Management task. During the IFC process, if the
software denies access to an object, the server process stops and a message appears.
 To view the status of the database interference detection process, right-click the
Interference Server icon in the Project Management tree, and click Properties. On the
Interference Server Settings dialog box, click the Status tab.
 When the database interference check process is running, only the Stop command is
available. When the process is not running, the Start command and all process property
gadgets are available. The Stop command is not available.
 When the database interference check is running and you add any permission group without
Read permissions for the server, the server automatically receives Read permissions and
finds collisions with the placed objects in that permission group.
 When you modify permission groups in Project Management, the host for the existing,
running task does not receive the changes. To update the information, you must exit and
restart the interference detection process.

Database Detect Tab (Interference Dialog Box)

Provides options for assigning interference checking priorities to aspects, specifying the
comparison methods, and optionally including a clearance rule. You can also assign the
interference results to a selected permission group.
All properties on this tab when viewed outside the Project Management task are read-only.
You must run Database Detect before running the delivered Interference report. The
Interference report is not intended to run on local interferences.
Check Model - Specifies the name of the model that the server process needs to check. The
server software must have the Site database locations predefined. This option is not available if
you are in the Project Management task.
On server - Specifies the name of the server on which the interference checking is processed
for the identified model.
Property - Lists all the object aspects identified for use in the model. This list includes the
system-defined aspects and the user-defined aspects. Select those aspects in the Property

Point Cloud User's Guide 27

Interference Checking
column that apply to your objects, and then specify the type of comparison in the Value column.
The delivered aspects include Simple physical, Detailed physical, Insulation, Operation,
Maintenance, Reference Geometry, and Centerline. The Diagnostic Interference Checking
report lists these aspects settings in its header.
Value - Lists the types of checking you can apply to the selected aspect: Required, Optional,
and Not checked. Choose the appropriate type for each aspect you select in the Aspect
column. Not checked means the software does not use the selected aspect for interference
checking.
Compare - Provides the following check box options for specifying which aspect types are to be
compared against each other to find interferences.
 Required - Required - Defines interferences classified as hard/hard. For example, one pipe
physically intersects another pipe.
 Required - Optional - Defines interferences that are not as severe and are classified as
hard/soft. For example, one pipe overlaps the optional aspect of the other object but does
not actually intersect the other object.
 Optional - Optional - Defines interferences that are not severe and are classified as
soft/soft. For example, the maintenance aspect of one piece of equipment overlaps the
maintenance aspect of another.
 Smart 3D - Foreign Interferences – Considers referenced 3D models, referenced PDS
objects, referenced MicroStation objects, and 3D AutoCAD files for interferences. This
option is enabled after you have selected a Model at the top of this tab. For PDS objects, the
selected Model must have an attached PDS project. For Database Detect, this box must be
checked for PDS objects to be considered. In the case of Local Detect, the software by
default considers referenced 3D models, PDS objects, MicroStation objects, and 3D
AutoCAD files that are in the workspace.

 This option only checks active model objects against foreign objects. The option does
not check for interferences between two foreign objects (PDS to 3D AutoCAD, for
example), except when the two foreign objects are referenced 3D models.
 Direct PDS project references are not processed in 64-bit IFC. You can either use
Reference 3D for your PDS projects or run 32-bit IFC.
 Smart 3D - Point Cloud - Considers an attached point cloud during interference checking.
The Point Cloud check box must be selected to consider Smart 3D objects and the point
cloud. The point cloud must have a valid connection to the model with no unresolved vendor
licensing issues for the Point Cloud check box to be available.
Include clearance rule - Specifies the clearance rule to add to the Required type of
interference check.
Assign results to permission group - Specifies the permission group to which all the detected
interferences are assigned. The list displays only those permission groups to which the server
containing the interference checking software has Write access.
Marker size - Specifies the size of the interference graphic marker. Choose a size that is clearly
readable, but one that does not interfere with the smaller details in the workspace view.
Start - Begins the process. This option is only available in the Project Management task.
Stop - Closes the process. This option is only available in the Project Management task.

28 Point Cloud User's Guide

Index
A W
Add Custom Commands • 19
What's New in Point Clouds • 15
C
Check Database Interferences • 32
Checking Interferences • 23
Common Applications • 19
Configure Interference Service Properties •
30
Create Filters • 19
Create IFC Permission Group Folder and
Permission Group • 31

D
Database Detect Tab (Interference Dialog
Box) • 34
Documentation Comments • 13
Documentation Set • 9

I
Install Database Interference Detection
Service • 29
Interference Checking • 23

M
Measure Point Cloud and 3D Data • 19

P
Point Clouds • 17
Preface • 7
Project Management • 21

R
Reference a Point Cloud • 21
Remove a Point Cloud Reference • 21

S
Server-Based Interference Checking
(Database Detect) • 27
Set IFC Permission Requirements • 31
Set IFC Permissions • 32
Start the Database Interference Detection
Service • 30

Point Cloud User's Guide 29