Terminal Blocks: J - Accessories

160TJ001 060220
Terminal blocks
J - Accessories
Summary
1. Mounting rails .................................................................................................................. 506
2. End stops ......................................................................................................................... 508
3. Circuit separators, seperator end sections .................................................................. 512
4. Jumper bars
Screw clamp jumper bars ..................................................................................................... 514

Screwless jumper bars .......................................................................................................... 517
Jumper bars for spring blocks .............................................................................................. 518
Jumper bars for railway terminal blocks ............................................................................... 519
5. Test accessories
Test connectors ..................................................................................................................... 521

Test devices ........................................................................................................................... 523
6. Other accessories
Comb-type jumper bars, insulation displacement jumper ................................................... 524

Connector plates, pivoting jumper bars, bridging or short-circuiting plugs, shield connectors ..... 525
7. Tools .................................................................................................................................. 526
505
Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected]

160T11016 051129
Mounting rails TS 35/F6 TS 35

Symmetrical - DIN 3
In compliance with EN 50022 standard In compliance with EN 50022 standard In compliance with EN 50022 standard
(DIN 46277-3 - NFC 63015) DIN 3 (DIN 46277-3 - NFC 63015) DIN 3 (DIN 46277-3 - NFC 63015) DIN 3
These rails are often used as grounding

bars. The current carrying capacity
of these rails and the copper wire sizes
required to carry that current are
given below.
RAIL CURRENT CARRYING CAPACITY

Current Wire size
Rail Material (A) AWG mm2
TS 35/F6 Steel 65 8 10
TS 35 Steel 87 6 16
TS 35/S Steel 87 6 16
TS 35 Aluminum 265 000 95
TS 35 Copper 150 0 50
TS 35CURRENT PlasticCARRYING 0 CAPACITY Type P/N Type P/N
RAIL
Current Wire size Type(TS 35/F6)
PR30 P/N 220.05
0173 Type (TS 35)
PR3.Z2 P/N 300.17
0174 Type P/N
White passivated galvanized steel, White passivated galvanized steel.
All
PR30 rails are in compliance
Steel with EN850022
65 10 PR30 1SNA 173(78")
220 R0500 PR3.Z2 1SNA 174 300 R1700 PR3.G2 1SNA 164 800 R0300
prepunched length 2 m 6'6" Length 2 m 6'6" (78") approx.
standard
PR3.Z2 (DINSteel
- PR3.G2 46277-3 - NFC
87 63015)6 16 approx. The length and prepunched Zinc bichromate plated steel, length White, passivated galvanized steel,
DIN
PR5 3. Steel 125 4 25 Zinc bichromate plated steel,
cut out dimensions are approximate. 2 m 6'6" (78") approx. length 2 m 6'6" (78") approx.
PR4 Steel 143 2 35 prepunched, length 2 m 6'6" (78")
PR30 (TS 35/F6)
approx. 0101 508.04
The length and prepunched PR3.Z2 (TS 35) 0101 513.10
Tolerances are ± unless otherwise noted. cut out1dimensions
Length m 3'3" (39")are approximate.
approx. Length 1 m 3'3" (39") approx.
TS 35/S TS 35 Aluminum Rail TS 35 Copper Rail
In compliance with EN 50022 standard

(NFC 63015) DIN 3
Sold in North America only.
In compliance with EN 50022 standard
(DIN 46277-3 - NFC 63015) DIN 3
J
1
Type P/N Type P/N Type P/N
Type P/N Type P/N Type P/N Type P/N
PR3.10 (TS 35/S) 0101 597.15 PR3.AL (TS 35) PR3.CU (TS 35) 0101 592.10
PR3.10 0101 597.15 PR5 0101 598.26 PR5 1SNA 168 700 R2200 PR4 1SNA 168 500 R1200
White passivated galvanized steel. Height Aluminum rail. Copper rail.
Zinc bichromate plated steel. Height Zinc bichromate plated steel, Zinc bichromate plated steel, length Zinc bichromate plated steel, length
10 mm (0.39"), length 2 m 6'6" (78") Length 2 m 6'6" (78") approx.
10 mm (0.39"), length 2 m 6'6" (78") prepunched length 2 m 6'6" (78") 2 m 6'6" (78") approx. 2 m 6'6" (78") approx.
approx.
approx. approx. The length and prepunched
cut out dimensions are approximate.
PR3.10 (TS 35/S) 0101 512.17 PR3.AL (TS 35) 0101 500.24 PR3.CU (TS 35) 0101 595.13
Length 1 m 3'3" (39") approx. Length 1 m 3'3" (39") approx. Length 1 m 3'3" (39") approx.
506
1012468_alts.indd 5 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 9:17:43 AM

160T11017 051129
TS 35/CF6 TS 35/C1 TS 35/C

Mounting rails
rails
Asymmetrical- -DIN
Symmetrical DIN31
Symmetrical - DIN 2
TS 35/C ALU
Asymmetrical 32 mm 1.26" G rail in Symmetrical type 1 12,2 x 5,1 rail in Symmetrical 15 mm .59" rail in compliance
compliance with EN 50035 standard compliance with NFC 93461 standard with EN 50045 standard
These rails are often used as grounding (DIN 46277-1 - NFC 63018) DIN 1 (DIN 46277.2)
bars. The current carrying capacity
of these rails and the copper wire sizes
required
The “Seriesto carry that current
M” terminal blocksaresnap
giventhe
onto below.
PR1 asymmetrical DIN 1 rails (aluminum rail only)
described here.
RAIL CURRENT CARRYING CAPACITY
Type P/N
The “Series DR” terminal Current
blocks Wire
snapsize 2
Rail symmetrical(A)
onto the PR2Material DIN 2AWGrail mm
TS 35/CF6 here.
described Steel 125 4 25
TS 35/C1 Steel 143 2 35
TS
The35/C Steel used as
rails are often 125grounding
4 25
TS 35/CThe
bars. ALU Aluminum
current 265capacity
carrying 000 95 Type P/N Type P/N Type P/N
High
of therail 90°andSteel
rails the copper 65wire sizes
8 10
PR5 (TS 35/CF6) 0101 598.26 PR4 (TS 35/C1) 0168 500.12 PR5 (TS 35/C)
High rail 30°
required Steelthat current
to carry 65 are given
8 10
White passivated galvanized steel, White passivated 1SNA
PRH1P galvanized steel.
163 390 R0600 White passivated galvanized steel.
below.
prepunched length 2 m 6'6" (78") Length 2anode-yellow
Aluminum m 6'6" (78") approx.
alloy, not Length 2 m 6'6" (78") approx. 0168 700.22
All rails are in compliance with EN 50022 approx. The length and prepunched cut prepunched - Length 1 m Length 1 m 3'3" (39") approx. 0101 515.12
standard (DIN 46277-3 Current
- NFC 63015)
Wire size out dimensions are approximate.
Type P/N Type P/N
DIN
Rail 3. Material (A) AWG mm2 PR5 (TS 35/CF6) 0101 509.05 PR4 (TS 35/C1) 0101 517.14 PR5.A2 (TS 35/C ALU)
PR1.Z2 - PR1.Z3 Steel 143 2 35 PR1.Z2 1SNA
Length 1 m 3'3" (39") 163 050 R0400
approx. Length 1 m 3'3" (39") approx. Reinforced aluminum.1SNA 164 600 R1200
PR2
PR1.A2 Aluminium 265 000 95 Zinc bichromate plated steel, length Length 2 m 6'6" zinc
Prepunched approx. 0101
(78") bichromate 502.26
plated
Tolerances are
PR2 ± unless otherwise
Steel 35 12noted.4 2 m 6'6" (78") approx. steel.1 m 3'3" (39") approx. 0101 899.24
Length
PR1.A2 1SNA 167 120 R2300
TS 35, High Aluminum
Rail 90°alloy, length TS 35, HighPR2PRail 30° 1SNA 206 596 R2500
3 m 9'9" (117") approx. Not prepunched zinc bichromate
PR1.Z3 1SNA 167 100 R0000 PRH1A 1SNA 163 400 R0100 plated steel.
Zinc bichromate plated steel, length Prepunched aluminum anode-yellow alloy

3 m 9'9" (117") approx. Length 1 m
Rail offset brackets
Insert for rail knockout: Insert for rail knockout:

Open grommet, black 0106 064.26 Open grommet, black 0106 064.26
Closed blind plug, black 0106 083.12 Closed blind plug, black 0106 083.12
Sold in North America only. Sold in North America only.
Deflection 90° Deflection 45°

Symmetrical type 2 21,8 x 6,4 mm
EM90 1SNA 008 520 R0100 EM45 1SNA 008 521 R2600 in compliance with NFC 93461 standard
J
1
Symmetrical type 2 reinforced

21,8 x 8,2 mm in compliance
Type P/Nwith Type P/N Type P/N Type P/N
NFC 93461 standard.
PR3.Z2 HR90anode-yellow
Aluminum ALU XUS001736
alloy, PR3.Z2 HR90 ALU XUS001735 PR3.Z2 HR30 ALU XUS001738 PR3.Z2 HR30 ALU XUS001737
length 2 m
Aluminum, prepunched length Aluminum. Aluminum
Aluminum,anode-yellow
prepunchedalloy,
lengthnot Prepunched
Aluminum. aluminum anode-yellow
2 m 6'6" (78") approx. The length and Length 1 m 3'3" (39") approx. prepunched - Length
2 m 6'6" (78") 2m
approx. The length and alloy - Length
Length 2 m(39") approx.
1 m 3'3"
prepunched cut out dimensions are prepunched cut out dimensions are
PRH2R
approximate. 1SNA 163 350 R1500 PRH2P 1SNA 163 370 R1100 PRH2A 1SNA 163 380 R0400
approximate.
507

Mounting rails End stops
TS 32 TS 32/F6 TS 15/F
Asymmetrical - DIN 1
Symmetrical - DIN 2
BADL
Characteristics
Screwless, snaps on rail without tool. V0 grey polyamide for DIN 3 rail. Maintained in place and locked on the rail with metal grips.
To reposition, do not slide on the rail. Withdraw and snap again (screwdriver DIA. 6,5 mm .256" max.)
TS 32 ALU
Thickness : 9 mm .354"
BADL Asymmetrical 32 mm 1.26" G rail in Asymmetrical 32 mm 1.26" G rail in Symmetrical rail 15 mm .59" in
compliance with EN 50035 standard compliance with EN 50035 standard compliance with EN 50045 standard
(DIN 46277-1 - NFC 63018) DIN 1
Selection (DIN 46277-1 - NFC 63018) DIN 1 (DIN 46277.2)
Description Type Order P/N Packaging Weight

kg
Screwless snap on end stop
grey (same colour as spring, ADO System®
The “Series 5000” terminal blocks and ATEX blocks) BADL 9 mm 1SNA 399 903 R0200
snap onto the PR1 asymmetrical
DIN 1 rails described here.
The “Series DR” terminal blocks snap

onto the PR2 symmetrical DIN 2 rail
described here.
These rails are often used as BAM2

grounding bars. The current carrying One meter only.
capacity of these rails and the copper
wire sizes required to carry that Type
Characteristics P/N Type P/N Type P/N
current are given below. PR1.Z2
End stop of (TS 32) equipped with a steel clamp allows
polyamide, PR1mounting on PR3, PR4 and PR5 (DIN 3) rails. PR2 (TS 15/F)
(TS 32/F6) 0101 673.00
Recommended screwdriver
White passivated : DIA. 5,5
galvanized mm .217"
steel. Prepunched white passivated Prepunched white passivated
Current Wire size
Recommended
Length 2 m 6'6"torque
(78") :approx.
Min. 0,8 mN - Max.
0163 1 mN Min.
050.04 7.1 lb.in - Max.
galvanized 8.9 lb.in
steel. galvanized steel.
Thickness : 10
Length 1 m 3'3" .394"
mm(39") approx. 0101 596.14 Length 1 m 3'3" (39") approx.
TS 32 Steel Length 2 m 6'6" (78") approx. 0101 501.25
BAM2143 2 35
TS 32 ALU Aluminum 265 000 95 Length 1 m 3'3" (39") approx. 0101 511.16
TS 32/F6 Steel 100 4 25 PR1.A2 (TS 32 ALU) PR2 (TS 15) 0101 674.01
Selection
TS 15/F Steel 35 12 4 Aluminum alloy Zinc bichromate plated steel.
TS 15 Steel 47 10 6 Length 2 m 6'6" (78") approx.
Description 0167 Type
120.23 Order P/N Not prepunched. Packaging Weight
Length 1 m 3'3" (39") approx. 0101 603.07 Length 1 m 3'3" (39") approx.kg
End stop equipped with a steel clamp
grey (same colour as screw blocks) BAM2 10 mm 1SNA 206 351 R1600
Rail tolerances grey (same colour as spring, ADO System®
BAM2 10 mm 1SNA 399 967 R0100
and ATEX blocks)
beige (same colour as railway blocks) BAM2 10 mm 1SNA 296 351 R0000
Symmetrical
center of rail
- DIN 3 Asymmetrical - DIN 1
Rail length: supplied in lengths of 1 or 2 meters or in Rail length: supplied in lengths of 1 or 2 meters or in
custom cut lengths. Allow 3 mm for the rail cutting custom cut lengths. Allow 3 mm for the rail cutting
blade thickness. blade thickness.
Accessories
Shown for DIN rails 35 mm wide and either 7.5 mm or Shown for DIN 1 rails 32 mm wide and 15 mm high.
Adjustable marker-holder for end stop
15 mm high. For other rail tolerances, contact Entrelec.
grey PEAD 1SNA 399 719 R1000
Dimensions apply over the whole length of the DIN rail,
Card of 40 blank markers for
Dimensions apply over the whole length of the DIN rail, but shall not be verified anywhere less than 10 mm
PEAD RCPEAD 29 x 9 mm 1SNA 399 725 R0600
but shall not be verified anywhere less than 10 mm from the ends.
Card of 20 transparent protection
from the ends.
markers for PEAD EPR2 1SNA 399 726 R0700
PEAD PIE24 All dimensions in millimeters.
All dimensions in millimeters. Marker-holder, white engraving on black
background, screw mounting on BADL PIE24 (1) 37 x 24 mm 1SNA 007 871 R2400
Marker-holder snapped on end stop
(no marker included)
(screw range) gris PEB 35 x 17 mm 1SNA 113 077 R1100
(Atex-Spring-ADO) gris PEB 35 x 17 mm 1SNA 195 077 R1400
Strip of 7 markers for PEB, to be
printed with AMS500 PIB3 35 x 17 mm 1SNA 235 462 R2200
J PEB - PIB... RC... Marker for PEB, white marking on
black background PIB 35 x 17 mm 1SNA 173 812 R1300
Protection for PIB... marker EPR1 1SNA 178 431 R2200
2 PEB marker holder with marker to be written by
hand or marking system, protection included PEBM 1SNA 113 084 R0100
Horizontal marker-holder, slide mouting
on top of end stop PEH 1SNA 163 211 R2600
PEH Card of 120 blank precut markers for
PEH RPEH 40 x 5 mm 1SNA 163 007 R2600
Markers RC810 8 mm see marking section
RC1010 10 mm
RPA
(1) For BADL only
508
160T11050 060112

End stops
Tall end stop BADH, BAEH

BADL
Characteristics
Characteristics
Tall end stop
Screwless, of polyamide,
snaps for use
on rail without with
tool. V0 M 70/22,
grey M 95/26
polyamide forblocks, power
DIN 3 rail. blocks, double
Maintained or and
in place triplelocked
deck blocks, andwith
on the rail electronic interface
metal grips.
modules
To series
reposition, do7000, 8000,
not slide on10000, 11000
the rail. and 30000.
Withdraw Snaps
and snap againon(screwdriver
rail - Easy mounting and repositioning,
DIA. 6,5 mm .256" max.) even between 2 blocks.
Recommended screwdriver : DIA. 5,5 mm .217"
Recommended
Thickness : 9 mmtorque
.354": Min. 1,2 Nm - Max. 1,4 Nm
Min. 10.6 lb.in - Max. 12.3 lb.in
BADL Thickness : 12 mm .472"
Selection
BADH
kg
and ATEX blocks) BADL 9 mm 1SNA 399 903 R0200
Selection

kg
Snap on end stop, mounting on symmetrical
BADH BAM2
DIN 3 rails grey BADH 12 mm 1SNA 116 900 R2700
Snap on end stop, mounting on asymmetrical
DIN 1 rail grey BAEH 12 mm 1SNA 116 934 R0400
Characteristics
End stop of polyamide, equipped with a steel clamp allows mounting on PR3, PR4 and PR5 (DIN 3) rails.
Recommended torque : Min. 0,8 mN - Max. 1 mN Min. 7.1 lb.in - Max. 8.9 lb.in
BAM2
Selection

kg
BAEH
Tall end stop BAMH
End stop equipped with a steel clamp
grey (same colour as screw blocks) BAM2 10 mm 1SNA 206 351 R1600
Characteristics
and end stop of V2 or V0 polyamideBAM2
ATEX blocks)
Multi-rail 102mm
equipped with blocking screws 399 967
1SNA allows R0100 on PR1, PR3, PR4 and PR5 (DIN 1, DIN 3) rails.
mounting
beige (same
Suitable forcolour
doubleasdeck
railway blocks)
blocks. BAM2 10 mm 1SNA 296 351 R0000
center of rail Recommended screwdriver : DIA. 5,5 mm .217"
Thickness : 9,1 mm .358"
Selection
Accessories
Description
Adjustable marker-holder for end stop Type Order P/N Packaging Weight
BAMH kg
grey PEAD 1SNA 399 719 R1000
Multi-rail end
Card of 40 blankstop
markers for grey BAMH 9,1 mm 1SNA 114 836 R0000
PEAD
Multi-rail end stop V0 beige RCPEAD
BAMH 299,1
x 9mm
mm 1SNA 194 725
1SNA 399 836 R0600
R0100
Card of 20 transparent protection
markers for PEAD EPR2 1SNA 399 726 R0700
PEAD PIE24
Marker-holder, white engraving on black
background, screw mounting on BADL PIE24 (1) 37 x 24 mm 1SNA 007 871 R2400
(screw range) gris PEB 35 x 17 mm 1SNA 113 077 R1100
Accessories
(Atex-Spring-ADO) gris PEB 35 x 17 mm 1SNA 195 077 R1400
J PEB - PIB... RC...
Marker for PEB, white marking on
PEB 35 x 17 mm 1SNA 113 077 R1100
J
Marker for PEB, white marking on
2 PEB marker holder with marker to be written by
2
hand or marking system, protection included PEBM 1SNA 113 084 R0100
Horizontal
PEB markermarker-holder,
holder with markerslide
to bemouting
written by
on toporof
hand end stop
marking system, protection included PEH
PEBM 1SNA 113 211
1SNA 163 084 R2600
R0100
PEH Card of 120 blank precut markers for
Horizontal marker-holder, slide mouting
PEB - PIB... RC... PEH RPEH 40 x 5 mm 1SNA 163 007 R2600
on top of end stop PEH 1SNA 163 211 R2600
Markers
Card of 120 blank precut markers for RC810 8 mm see marking section
PEH RC1010
RPEH 10xmm
40 5 mm 1SNA 163 007 R2600
RPA
Card of 100 markers for vertical marking RC810 8 mm see marking section
(1) For BADL only RC1010 10 mm
PEH
RPA
508 509
160T11050 060112 160T11054 051129

End
End stops
stops
Tall
BADRLend stop BADH, BAEH
Characteristics
Characteristics
Tall
Endend
stopstop of grey
of V0 polyamide, for use
polyamide withonMDIN
snaps 70/22, M 95/26
2 rail, blocks, maintained
automatically power blocks, double
in place or metal
with triple deck
grips.blocks, and electronic interface
modules seriesdo
To reposition, 7000,
not 8000, 10000,
slide on 11000
Withdraw Snaps
and snap on rail
again - Easy mounting
(screwdriver and repositioning,
DIA. 4 mm .157" max.) even between 2 blocks.
Recommended
Thickness : 6,5 torque : Min. 1,2 Nm - Max. 1,4 Nm
mm .256"
BADRL
Selection
BADH
kg
and ATEX blocks) BADRL 6,5 mm 1SNA 199 420 R2100
Selection

kg
BADH BAR
DIN 3 rails grey BADH 12 mm 1SNA 116 900 R2700
Characteristics
DIN 1 rail grey BAEH 12 mm 1SNA 116 934 R0400
Butée d'arrêt réversible en polyamide beige avec équerre de blocage. Montage vertical ou à 30°, sur PR1 uniquement.
Épaisseur : 10 mm .394"
BAR
Selection

kg
BAEH
Tall end
Screwless snap stop BAMH
on end stop
beige (same colour as railway blocks) BAR 10 mm 1SNA 164 519 R2400
Characteristics
Multi-rail end stop of V2 or V0 polyamide equipped with 2 blocking screws allows mounting on PR1, PR3, PR4 and PR5 (DIN 1, DIN 3) rails.
Suitable for double deck blocks.
Selection

BAMH kg
Multi-rail end stop grey BAMH 9,1 mm 1SNA 114 836 R0000
Multi-rail end stop V0 beige BAMH 9,1 mm 1SNA 194 836 R0100
Accessories
Marker-holder for group marking, white
engraving on black ground, screw mounting
on end stop PIE9 (1) 37 x 9 mm 1SNA 167 257 R0000
Marker-holder, white engraving on black
Accessories
background, screw mounting on end stops PIE24 (1) 37 x 24 mm 1SNA 007 871 R2400
Mounting screw VST28 (1) 1SNA 167 335 R2600
PIB... Marker-holder snapped on end stop
J PIE...
(no marker
Strip included)
of 7 markers for PEB, to be
PEB
PEB
35 x 17 mm
35 x 17 mm
1SNA 113 077 R1100
1SNA 113 077 R1100 J
Strip ofwith
printed 7 markers
AMS500 for PEB, to be PIB3 35 x 17 mm 1SNA 235 462 R2200
printed with AMS500
Marker for PEB, white marking on PIB3 35 x 17 mm 1SNA 235 462 R2200
2 Marker
black for PEB, white marking on
background PIB 35 x 17 mm 1SNA 173 812 R1300
2
RPA black background
Protection for PIB... marker PIB
EPR1 35 x 17 mm 173431
1SNA178
1SNA 812R2200
R1300
Protection
PEB for PIB...
marker holder marker
with marker to be written by EPR1 1SNA 178 431 R2200
hand or marking system, protection included
Markers PEBM
RC610 (2) 6 mm 1SNA 113 084section
see marking R0100
Horizontal marker-holder, slide mouting RPA (1)
PEB - PIB... RC... on top of end stop PEH 1SNA 163 211 R2600
Card of 120 blank precut markers for
(1) BAR only
PEH RPEH 40 x 5 mm 1SNA 163 007 R2600
(2) BADRL only
RC1010 10 mm
PEH
RPA
510 509
160T11069 051129 160T11054 051129

Notes
End stops End stops
Tall end stop BADH, BAEH

BADRL BADRL
Characteristics
Characteristics Characteristics
Tall end
End stopstop
of V0ofgrey
polyamide,
polyamidefor snaps
use withonM 70/22,
DIN 2 rail,Mautomatically
95/26 blocks,maintained
power blocks, double
in place withormetal
triplegrips.
deck blocks, and electronic interface End stop of V0 grey polyamide
modules
To series
reposition, do7000, 8000,
not slide on10000, 11000
Withdraw and snapSnaps on(screwdriver
again rail - Easy mounting
DIA. 4 mmand.157"
repositioning,
max.) even between 2 blocks. To reposition, do not slide on th
Recommended
Thickness torque
: 6,5 mm : Min. 1,2 Nm - Max. 1,4 Nm
.256" Thickness : 6,5 mm .256"
BADRL BADRL
Selection Selection
BADH
Description Type Order P/N Description
Packaging Weight
kg
Screwless snap on end stop Screwless snap on end stop
grey (same colour as spring, ADO System® grey (same colour as spring, ADO S
and ATEX blocks) BADRL 6,5 mm 1SNA 199 420 R2100 and ATEX blocks)
Selection

kg
BADH BAR
DIN 3 rails grey BADH 12 mm 1SNA 116 900 R2700 BAR
Characteristics
DIN 1 rail grey BAEH 12 mm 1SNA 116 934 R0400 Characteristics
Butée d'arrêt réversible en polyamide beige avec équerre de blocage. Montage vertical ou à 30°, sur PR1 uniquement. Butée d'arrêt réversible en poly
Épaisseur : 10 mm .394" Épaisseur : 10 mm .394"
BAR BAR
Selection Selection
Description Type Order P/N Description

Packaging Weight
kg
BAEH
Tall end stop BAMH
Screwless snap on end stop Screwless snap on end stop
beige (same colour as railway blocks) BAR 10 mm 1SNA 164 519 R2400 beige (same colour as railway blo
Characteristics
Multi-rail end stop of V2 or V0 polyamide equipped with 2 blocking screws allows mounting on PR1, PR3, PR4 and PR5 (DIN 1, DIN 3) rails.
Suitable for double deck blocks.
Selection

BAMH kg
Multi-rail end stop grey BAMH 9,1 mm 1SNA 114 836 R0000
Multi-rail end stop V0 beige BAMH 9,1 mm 1SNA 194 836 R0100
Accessories Accessories
Marker-holder for group marking, white Marker-holder for group marking, whi
engraving on black ground, screw mounting engraving on black ground, screw mo
on end stop PIE9 (1) 37 x 9 mm 1SNA 167 257 R0000 on end stop
Marker-holder, white engraving on black Marker-holder, white engraving on bla
Accessories
background, screw mounting on end stops PIE24 (1) 37 x 24 mm 1SNA 007 871 R2400 background, screw mounting on end
Mounting screw VST28 (1) 1SNA 167 335 R2600 Mounting screw
PIB... Marker-holder snapped on end stop PIB...
Marker-holder snapped on end
J J
J
(no marker included) PEB 35 x 17 mm 1SNA 113 077 R1100
PIE... (no marker
Strip included)
of 7 markers for PEB, to be PEB 35 x 17 mm 1SNA 113 077 R1100 PIE... (no marker included)
Strip of 7 markers
printed with AMS500 for PEB, to be PIB3 35 x 17 mm 1SNA 235 462 R2200 Strip of 7 markers for PEB, to b
printed with AMS500
Marker for PEB, white marking on PIB3 35 x 17 mm 1SNA 235 462 R2200 printed with AMS500
2 Marker for PEB, white marking on
black background PIB 35 x 17 mm
2
1SNA 173 812 R1300
2
Marker for PEB, white marking
RPA RPA black background
black background
Protection for PIB... marker PIB
EPR1 35 x 17 mm 1SNA 173
1SNA 178 812
431 R1300
R2200
Protection
PEB marker for PIB...
holder withmarker
marker to be written by EPR1 1SNA 178 431 R2200 Protection for PIB... marker
Markers PEBM (2)

hand or marking system, protection included
RC610 6 mm 1SNA 113 084section
see marking R0100 Markers
Horizontal marker-holder, slide mouting RPA (1)
PEB - PIB... RC... on top of end stop PEH 1SNA 163 211 R2600
Card of 120 blank precut markers for
(1) BAR only (1) BAR only
PEH RPEH 40 x 5 mm 1SNA 163 007 R2600
(2) BADRL only (2) BADRL only
RC1010 10 mm
PEH
RPA
510 510 511

509
160T11069 051129 160T11069
160T11054 051129
NOTE_511051129

Circuit separators
Separator end sections
Product Type Order P/N Product Type Order P/N
Possibility of marking, by the user, on the back of the With possibility of mounting a protective cover CPM, and a
marker-holder PEP. Extends 5 mm .20" on sides of the block
separator.
For blocks : M 4/6 except D and G and 11,5 mm .45" on top (1).
For blocks : MA 2,5/5 (1)
M 6/8 - M 10/10
M 4/6.H M 4/6 except D and G (1) (2)
M 1,5/6.HH and ADV M 6/8 - M 10/10 (1) (2)
Width : 51 mm 2.01" M 4/6.H (1)
Height : 59,5 mm 2.34"
67 mm 2.64"
Separator end section grey SCF61 1SNA 114 202 R2500 64,5 mm 2.54"
Width : 51 mm 2.01"
For M 4/6.D block only. Extends 2 mm .079" around the (1) For SCF6, snapped on block
block. (2) For SCFM6, mounting on PR1, PR4 and PR5 rails
Separator end section grey SCF6 1SNA 118 707 R0300
Height : 61,5 mm 2.42"
blue SCF6 1SNA 128 707 R0500
69 mm 2.72"
66,5 mm 2.62" grey SCFM6 1SNA 114 825 R0500
With possibility of mounting a protective cover CPM, and a
marker-holder PEP. Extends 5 mm .20" on sides of the block
Separator end section grey SCF6.D 1SNA 118 495 R1700
and 11,5 mm .45" on top.
For blocks : M 4/6.G (1)
Only for NTLP blocks. M 16/12 (2)
(1) With cut-out for busbar passage. Snapped on PR3, PR4 M 35/16 (3)
and PR5 rails. Extends 3 mm .12" around the block excepting M 70/22 (4)
on top. M 6/8.ST(5)
(2) Snapped onto the extremity of the BJM62 connector bars
SCF.D before they are mounted on the blocks. Thickness : 3 mm .118"
Separator end section grey SCF6G (1) 1SNA 113 075 R1700
Thickness (1) : 1,5 mm .059" grey SCF12 (2) 1SNA 113 102 R1000
SCD grey SCF16 (3) 1SNA 113 101 R1700
Separator end section grey SCF.D (1) 1SNA 114 117 R0700 grey SCF22 (4) 1SNA 113 851 R1600
Circuit separator white SCD (2) 1SNA 103 189 R2600 grey SCFT2 (5) 1SNA 114 522 R0500
For spring blocks. With possibility of mounting a protective cover CPM, and a
marker-holder PEP. Snap on mounting on PR1, PR3, PR4
Thickness : 2,5 mm .098" and PR5. This separator does not replace an end section
which must be used on the block.
For blocks : M 6/9.EE
Separator end section grey SCD5.2L 1SNA 291 351 R0300 M 6/12.FF
orange SCD5.2L 1SNA 291 352 R0400 Thickness : 1 mm .039"
orange SCD5.3L 1SNA 291 362 R0600
orange SCD5.4L 1SNA 291 372 R0000 Separator end section white SCF9 1SNA 103 672 R0100
The SCM separator snaps onto the top of the open terminal blocks, once
Separator for use with 1/4 turn terminal blocks, with
the terminal board is assembled. It does not increase the thickness of the
possibility of mounting one or two protective covers CPM
blocks but extends 8 mm .315" on top.
side by side. Snap on mounting on PR1, PR3, PR4 and PR5
For blocks : MA 2,5/5 (1)
rails.
MA 2,5/5.D (2)
Height : 63 mm 2.48"
M 1,5/6.HH and ADV blocks, M 4/6, M 6/8,
70,5 mm 2.78"
M 10/10, M 16/12 (3)
68 mm 2.68"
M 4/6.D (4)
Width : 77,5 mm 3.05"
SCM... ADO System® blocks (5)
Circuit separator grey SCMA5 (1) 1SNA 116 728 R2500 Separator end section grey SCFT1* 1SNA 103 588 R2600
grey SCMA5D (2) 1SNA 116 720 R2100
Accessories :
grey SCM6 (3) 1SNA 113 003 R1000
CPM cover protects the user from accidental touch on live
orange SCM6 (3) 1SNA 103 233 R2100
circuits. It is clipped onto the end sections (FE), onto the
grey SCM6D (4) 1SNA 113 482 R0500 intermediate sections (FJ) and onto the SCF, SCFT or SCFM
grey SCAD (5) 1SNA 196 896 R0000 separators. It can also be used for marking the terminal unit by
J means of a blank strip RTC, which slides into the cover.
CPM + RTC CPM width : 32 mm 1.26"

3 CPM length : 500 mm 19.70"
RTC width : 20 mm .79"
RTC length : 1 m 39"
Protective cover clear CPM 1SNA 187 312 R1400

beige 1SNA 197 312 R1600
Top marking strip for CPM RTC 1SNA 163 156 R2700
Marker holder PEP 1SNA 113 762 R2400
This marker holder snaps on separator end sections SCF or

SCFM and on the ECP and ECS power blocks' partitions.
It can receive 1 label RC610.
*Note : Not to be mounted on SCFT1 separator end section.
512 PEP
160T11070 051129

Circuit separators
Separator end sections (cont.)
Product Type Order P/N Product Type Order P/N
With possibility of mounting a protective cover CPV, and a

marker-holder PEP. Snap on mounting on PR1, PR3, PR4
and PR5 rails.
For blocks :
MA 2,5/5 - M 4/6 - M 6/8 - M 10/10 - M 16/12 - M 35/16 (1)
M 6/8.STA - M 6/8.SF (2)
M 70/22 - M 10/12.SF - MB 10/24.SF - MB 25/30.SF -
MU 10/13 - M 10/13.TSF (3)
M 6/8.ST (4)
SCFCV + CPV
Separator end section grey SCFCV1-2 (1) 1SNA 116 795 R1100
grey SCFCV3 (2) 1SNA 116 796 R1200
grey SCFCV4 (3) 1SNA 116 797 R1300
grey SCFCV5 (4) 1SNA 116 798 R2400
Accessories :
Protective cover of transparent PVC, length 1 m 3'3" (39") approx.
For cover mounting, place a separator end section SCFCV every
400 mm approx., at terminal assembly extremities. It can also be
used for marking the terminal unit by means of a blank marker strip
RTC, which sticks under the cover.
RTC width : 20 mm .79"
RTC length : 1 m 39"
Separator Cover Width Height
SCFCV1-2 CPV1-2 73 mm 2.87" 66 mm 2.62"
74 mm 2.91"
72 mm 2.83"
SCFCV3 CPV3 85 mm 3.35" 68,5 mm 2.70"
76 mm 2.99"
74 mm 2.91"
SCFCV4 CPV4-S 85 mm 3.35" 68,5 mm 2.70"
76 mm 2.99"
74 mm 2.91"
SCFCV5 CPV4-S 104 mm 4.09" 72 mm 2.83"
79,5 mm 3.13"
77,5 mm 3.05"
Protective cover clear CPV1-2 1SNA 176 816 R1200
clear CPV3 1SNA 176 817 R1300
clear CPV4-S 1SNA 176 791 R2100
Top marking strip RTC 1SNA 163 156 R2700
Marker holder PEP 1SNA 113 762 R2400
This marker holder snaps on separator end section SCFCV.

It can receive 1 label RC610.
PEP
J
3
513
160T11071 051129

Jumper bars for screw clamp and ADO System®
terminal blocks
IP20 assembled screw jumper bars
Fractionable model, composed of captive screws on a jumper bar system, with IP20 protection touchproof. This accessory can be used for
connecting consecutive blocks only.
Max. recommended torque : 0,6 Nm
Selection

kg
IP20 jumper bar for blocks MA 2,5/5
24 A - 2 poles BJMI5 1SNA 176 278 R1600
24 A - 3 poles BJMI5 1SNA 176 279 R1700
24 A - 4 poles BJMI5 1SNA 176 280 R0500
24 A - 5 poles BJMI5 1SNA 176 281 R2200
24 A - 10 poles BJMI5 1SNA 176 282 R2300
IP20 jumper bar for blocks M 4/6
32 A - 2 poles BJMI6 1SNA 176 663 R0000
32 A - 3 poles BJMI6 1SNA 176 664 R0100
32 A - 4 poles BJMI6 1SNA 176 665 R0200
32 A - 5 poles BJMI6 1SNA 176 666 R0300
BJMI5 - BJMI6 - BJMI8
32 A - 10 poles BJMI6 1SNA 176 667 R0400
41 A - 2 poles BJMI8 1SNA 176 669 R1600
41 A - 3 poles BJMI8 1SNA 176 670 R1300
41 A - 4 poles BJMI8 1SNA 176 671 R0000
41 A - 5 poles BJMI8 1SNA 176 672 R0100
41 A - 10 poles BJMI8 1SNA 176 673 R0200
Simplified model, composed of a bar prepunched to the spacing of the blocks, and of captive screws and spacers. This accessory can be
used for connecting blocks which are consecutive or not : in this case remove the screw and spacer which are not required.

except for BJMI16 : 1,2 Nm
Selection

kg
IP20 jumper bar for blocks MA 2,5/5.D
24 A - 2 poles BJMI5D 1SNA 176 736 R2100
IP20 jumper bar for blocks M 4/6.D
57 A - 2 poles BJMI10 1SNA 176 675 R0400
BJMI5D - BJMI6D - BJMI10 - 57 A - 3 poles BJMI10 1SNA 176 676 R0500
BJMI12 - BJMI16 57 A - 4 poles BJMI10 1SNA 176 677 R0600
57 A - 5 poles BJMI10 1SNA 176 678 R1700
57 A - 10 poles 1SNA 176 679 R1000
J IP20 jumper bar for blocks M 16/12
BJMI10
76 A - 2 poles BJMI12 1SNA 179 626 R0600

4 76 A - 3 poles BJMI12 1SNA 179 628 R1000
76 A - 4 poles BJMI12 1SNA 179 629 R1100
76 A - 5 poles BJMI12 1SNA 179 630 R1600
76 A - 10 poles BJMI12 1SNA 179 631 R0300
110 A - 2 poles BJMI16 1SNA 206 217 R0000
110 A - 3 poles BJMI16 1SNA 206 218 R1100
110 A - 4 poles BJMI16 1SNA 206 219 R1200
110 A - 5 poles BJMI16 1SNA 206 220 R1700
110 A - 10 poles BJMI16 1SNA 206 221 R0400
514
160T11078 051129

terminal blocks
Not assembled screw jumper bars

To connect terminal blocks, place the metal tube into the top center hole on each terminal block to be connected. The metal tube contacts the terminal block's internal
connector bar. The perforated bar is cut to length and placed flat along the center opening of the series of terminal blocks. The screw is inserted into the perforated bar's
hole which is located directly above the blocks being connected. The screw goes through the threaded metal tube and is screwed into the terminal block's internal
connector bar. This completes the electrical connection to the perforated bar and connects the block.
Selection
kg
Post + screw + washer for blocks
MA 2,5/5 and DR 1,5/5 EV5 1SNA 168 629 R1600
Perforated jumper bar for
blocks MA 2,5/5 and DR 1,5/5 BJS5 20 poles - 24 A 1SNA 177 652 R0600
Post + screw + washer for block MA 2,5/5.D EV5D 1SNA 176 260 R1000
Jumper bar for block MA 2,5/5.D BJS5D 20 poles - 24 A 1SNA 177 651 R0500
Post + screw + washer for block M 4/6 EV6 1SNA 168 604 R1600
Subassembly Insulated post + screw + washer for block M 4/6 EV6I 1SNA 206 394 R0200
screw + washer + post Jumper bar for block M 4/6 BJS6 20 poles - 32 A 1SNA 174 784 R2000
Post + screw + washer for blocks
M 4/6.D and MD 2,5/6... EV6D 1SNA 168 400 R1600
blocks M 4/6.D and MD 2,5/6... BJS61 10 poles - 32 A 1SNA 168 485 R2700
Perforated jumper bar 1SNA 168 399 R1000
Post + screw + washer for block DR 4/6 EVDR6
to be cut to length 1SNA 167 601 R0200
Jumper bar for block DR 4/6 BJS62D 10 poles - 24 A
Post + screw + washer for block M 6/8.ST EV8S 1SNA 168 401 R0300
Post + screw + washer for block M 4/8.D2.SF...J VJS11 1SNA 163 394 R2600
Perforated jumper bar for blocks
M 6/8 - M 6/8.ST - M 4/8.D5.SF...J BJS8 20 poles - 41 A 1SNA 174 789 R0500
Jumper bar for block M 6/9.EE BJS9,5 10 poles - 41 A 1SNA 173 819 R2200
Jumper bar for block M 10/10 BJS10 20 poles - 57 A 1SNA 177 654 R0000
Screw for block MB 10/12.SF 1SNA 163 574 R2200
Washer for block MB 10/12.SF 1SNA 163 633 R2500
blocks M 16/12 and MB 10/12.SF BJS12 20 poles - 57 A 1SNA 177 653 R0700
Jumper bar for block M 6/12.FF BJS12,5 10 poles - 41 A 1SNA 174 396 R2300
Jumper bar for block M 6/13.FF BJS13 10 poles - 125 A 1SNA 167 224 R2700
Screw for block ML 10/13.SF 1SNA 163 394 R2600
Washer for block ML 10/13.SF 1SNA 168 783 R0100
Jumper bar for block ML 10/13.SF BJS131 10 poles - 57 A 1SNA 175 991 R1100
Screw for block M 70/22 1SNA 173 320 R0100
Washer for block M 70/22 1SNA 173 331 R2000
Screw for block MB 10/24.SF 1SNA 163 607 R0400
Jumper bar for block MB 10/24.SF BJS24 10 poles - 30 A 1SNA 167 856 R2100
Post + screw + washer for block M 95/26 VJS51 1SNA 173 320 R0100
Washer for block M 95/26 1SNA 173 331 R2000
Screw jumper bars for alternated jumping

This accessory permits the interconnection of consecutive or non-consecutive blocks. For this, detach the studs manually where connection
is not required. The use of two bars permits alternated jumping. A captive screw is mounted on each stud. This jumper bar is delivered with
J
+ a protective cover snapped onto the top of the block, assuring touch proof protection.
Note : At each extremity of the jumpers the assembly must be insulated. For this, use either a closed block or a circuit separator SC.
4
Selection
Jumper bar assembly for blocks with
5 mm .200’’ spacing 10 poles BJA5 24 A 1SNA 205 021 R2600
30 poles BJA5 24 A 1SNA 205 197 R2400
Jumper bar assembly for blocks with
Jumper bar assembly, protective cover 6 mm .238’’ spacing 10 poles 1SNA 116 541 R1200
BJA6 35 A
included 30 poles BJA6 35 A 1SNA 116 589 R1300
Protective cover alone 10 poles
for BJA5 grey 1SNA 119 847 R2000
for BJA6 grey 1SNA 116 508 R2200
Protective cover white 1SNA 103 819 R2500
515
160T11068 051129

terminal blocks
Universal screw jumper bars

This accessory permits the interconnection of two consecutive blocks with different spacings. It is composed of : 2 posts, 2 screws,
2 washers, 1 connector plate.
IV IV 8
Spacing of block B
Spacing of block 6 corresponds to M 4/6 and its derivatives.
Spacing of block 6,5 corresponds to M 4/6,5 and its derivatives. V IV IV 10
Spacing of block 8 corresponds to M 6/8 and its derivatives. III III III III 12
II I I I I 16
Spacing of block 16 corresponds to M 35/16 and its derivatives. 12 10 8 6.5 6
Max. recommended torque : 0,6 Nm Spacing of block A
Selection
kg
BJDP... Jumper bar kit N° I BJDP1 50 A 1SNA 179 623 R0300
Jumper bar kit N° II BJDP2 95 A 1SNA 179 624 R0400
Jumper bar kit N° III BJDP3 70 A 1SNA 179 625 R0500
Jumper bar kit N° IV BJDP4 50 A 1SNA 174 781 R2500
Jumper bar kit N° V BJDP5 50 A 1SNA 174 782 R2600
J
4
516
160T11080 060529

terminal blocks
Screwless jumper bars for ADO System® blocks and miniblocks with 5
or 6 mm spacing only
This accessory permits the interconnection of consecutive or non-consecutive blocks. For this, detach the studs manually where connection
is not required. Thanks to its flexible connection system, the contact is made by a simple insertion into the ADO jaw. 2 wire connection
remains permitted. Protection : NEMA 1 - Marking with RCT 610 and RCT 810 markers.
* Important : It is necessary to remove the jumper bar to work on the wiring.
Selection
kg
Screwless jumper bar for blocks with
5 mm .200’’ spacing 2 poles BJADO5.2 13,5 A 1SNA 205 955 R0300
3 poles BJADO5.3 13,5 A 1SNA 205 956 R0400
BJADO... Screwless jumper bar for blocks with
6 mm .238’’ spacing 2 poles BJADO5.2 17,5 A 1SNA 205 974 R0600
J
4
517
160T11081 051129

Jumper bars for spring blocks
BJDL... jumper bar for spring blocks with the same spacing
This accessory allows to connect two blocks next to each other or not. For this, remove manualy the unconnected metal pins by folding
them several times. Identification of cut pins is possible.
This flexible connecting system allows contact by simple insertion.
BJDL5.2
Selection
kg
Jumper bar for spring blocks with 5 mm
.200’’ spacing 10 poles BJDL5.10 1SNA 291 110 R2600


BJDL5.4 + remove manualy Jumper bar for spring blocks with 10 mm
(by successive folding) .400’’ spacing 5 poles BJDL10.5 24 A 1SNA 291 325 R2100
the unused metal pin
.400’’ spacing 5 poles BJDL1.10.5 57 A 1SNA 291 478 R0300
BJDPL... jumper bar for spring blocks with different spacings

This accessory allows the connection of 2 spring terminal blocks with different spacings to each other (spacing 5 and 6 mm, 6 and 8 mm, 5
and 8 mm). It is not necessary to use a spring block with an additional spring to jump with a wire, but it is necessary to use an end section
between the interconnected blocks, whatever the mounting direction of the blocks may be. These jumper bars and both slots for jumper
bars permit current distribution (see ‘’Example’’ drawing).
Selection
Example : Input block Output block Type Order P/N Current max.
End section
Distribution
blocks 6 mm .238’’ spacing 5 mm .200’’ spacing BJDPL5.6 1SNA 291 150 R0600 24 A
8 mm .315’’ spacing 5 mm .200’’ spacing BJDPL5.8 1SNA 291 160 R0000 24 A
Power 6 mm .238’’ spacing BJDPL6.8 1SNA 291 170 R0200 32 A
block 10 mm .400’’ spacing 5 mm .200’’ spacing BJDPL5.10 1SNA 291 480 R2200 24 A
6 mm .238’’ spacing BJDPL6.10 1SNA 291 482 R1000 32 A
8 mm .315’’ spacing BJDPL8.10 1SNA 291 484 R1200 41 A
12 mm .473’’ spacing 6 mm .238’’ spacing BJDPL6.12 1SNA 399 613 R0600 32 A
I = i1 + i2 + i3 + i4 < Imax shunt
ETRES1 explaining sticker

These stickers show how to use a spring block.
Selection

kg
Explaining sticker ETRES1 1SNB 000 051 R0600
J
4
518
160T11082 051129

BJHS distribution bars for railway terminal blocks
BJHS
Characteristics
Jumper bar to be sawing divided for transversal interconnection between several terminal blocks.
Selection

kg
Connexion between one 16 mm block with M6
stud and one 8 mm block for quick connect tabs
Assembly 1: left end stud block BJHS-ENT7192 1SNA 178 803 R0000
Assembly 1: right end stud block BJHS-ENT7193 1SNA 178 802 R0700
Accessories
End section Closing plate FEH3 th. 1 mm 1SNA 198 352 R0700
Screw for BJHS VSJ6 1SNA 167 735 R2700
Washer for VSJ RDJ6 1SNA 173 241 R0600
Selection

kg
Connexion between one M6, M8 or M10 stud block
and one type HD 2.5/6.3... longitudinal tongued block
Assembly 1: left end stud block BJHS 1SNA 179 782 R0300
Assembly 1: right end stud block BJHS 1SNA 179 781 R0200
End section
Accessories
Closing plate FEHD2 th. 1 mm 1SNA 168 949 R1700
Screw for BJHS VSJ6 1SNA 167 735 R2700
Washer for VSJ RDJ6 1SNA 173 241 R0600
BJM
BJHS
Selection

kg
J
Connexion between one M6, M8 or M10 stud block
and one NF ADO System® terminal block 4
Assembly : left end stud block BJHS 1SNA 206 539 R0300
519
160T11074 051129

BJH jumper bars for railway terminal blocks
Characteristics
Perforated bar, which can be cut by sawing, for making transverse connections between two or more identical terminal blocks.
Selection

kg
Jumper bar for blocks Spacing 6 mm BJH6 2 poles 1SNA 168 481 R2300
with quick connect BJH6 3 poles 1SNA 168 482 R2400
BJH6 4 poles 1SNA 168 483 R2500
BJH6 5 poles 1SNA 168 484 R2600
BJH6 10 poles 1SNA 168 485 R2700
BJH7 4 poles 1SNA 168 488 R0200
BJH7 5 poles 1SNA 168 489 R0300
BJH7 10 poles 1SNA 168 490 R0000
BJH8 4 poles 1SNA 168 458 R1300
BJH8 5 poles 1SNA 168 459 R1400
BJH8 10 poles 1SNA 168 356 R1400
BJH9 4 poles 1SNA 168 462 R0700
BJH9 5 poles 1SNA 168 463 R0000
BJH9 10 poles 1SNA 168 357 R1500
Jumper bar for blocks Sp. 11,2 mm BJH11 10 poles 1SNA 164 562 R2700
with quick connect
Jumper bar for blocks Sp. 13,2 mm BJH13 10 poles 1SNA 163 556 R2000
with quick connect
For quick connect blocks, a sub-assembly must be used: screw plus washer to connect the jumper bar onto the required block.
Accessories
Screw for HD type blocks VSJ6 1SNA 167 735 R2700
Washer for HD type blocks RDJ6 1SNA 173 241 R0600
Screw for H type blocks VSJ11 1SNA 163 394 R2600
Washer for H type blocks RDJ11 1SNA 168 783 R0100
For stud blocks, the jumper bar is fitted under the washer and the nut of each block to be shunted.
Selection

kg
Jumper bar for Spacing 13,2 mm BJH131 10 poles 1SNA 163 468 R0000
stud block
Jumper bar for Spacing 13 mm BJH132 10 poles 1SNA 167 224 R2700
stud block
Jumper bar for Spacing 14 mm BJH14 2 poles 1SNA 173 438 R2400
stud block BJH14 3 poles 1SNA 173 439 R2500
BJH14 4 poles 1SNA 173 441 R2700
BJH14 5 poles 1SNA 173 449 R0700
BJH14 10 poles 1SNA 173 451 R2100
stud block
J stud block 3 poles 1SNA 173 453 R2300
4 poles 1SNA 173 454 R2400
5 poles 1SNA 173 460 R0600
4 10 poles 1SNA 173 461 R2300
stud block
For H type stud block, an IN spacer is necessary in order to ensure insulation between the jumper bar and the rail.
Accessories
Spacer 1,2 mm INH1 1SNA 193 474 R1500
Spacer 1,2 mm yellow INH1 1SNA 199 396 R2500
Spacer 4 mm INH3 1SNA 199 394 R2300
520
160T11076 051129

Test connectors
For screw clamp blocks DIN 1-3
For spring blocks DIN 1-3
CEV... test connectors for screw clamp blocks

Characteristics IEC UL CSA
NFC VDE
Wire size Rigid

mm² Flexible 0.5(1) - 0,34
Voltage V 250 (2)
Current A 2 (1) For CEV 6.1 only
Short circuit current (M 4/6.PI) A/s (2) For low voltages (<24 V) take a typical contact
Rated wire size mm² / AWG resistance of 50 mW into account.
Wire stripping length mm / inches
Recommended torque Nm / Ib.in
Test connector CEV...
To perform simple tests quickly :
This connector completes the range of modular connectors to mount on terminal strips. It is supplied ready for use, without any
modification of the terminal strip :
The contact is made on the wire-clamp screw heads.
Fastening is performed on the terminal block wire inputs.
These connectors are supplied connected with 2 meters (6.6 Ft.) long wires, size 0,34 mm² (22 AWG). Standard 1 pole and 10 pole models
are kept in stock. However, on request, 4 to 15 pole models are available.
Selection

kg
Unit connector 1 pole grey CEV 6.1 1SNA 115 544 R1400
Test connector 10 poles grey CEV 6.10 6 mm 1SNA 115 573 R1100
Unit connector
Simple test
connector (1 pole)
supplied with a 2
meters (6.6 Ft.) long
wire.
CEL... test connectors for spring blocks

NFC VDE
Wire size Rigid

mm² Flexible
Voltage V
Current A
Short circuit current (M 4/6.PI) A/s
Rated wire size mm² / AWG 1,5 mm²
Selection

kg
Test connector for standard 5 mm
spacing spring blocks grey CEL 1.5 1SNA 400 262 R1400
Test connector CEL... spacing spring blocks grey CEL 1.8 1SNA 400 264 R1600 J
End module of connector grey CEL 1.E 1SNA 400 265 R1700
Test connector for angled 5 mm
5
End module of connector grey CEL 2.E 1SNA 400 261 R1300
Accessories
Markers RC 55 see section on markers
521
160T11001 051129

Test connectors
For ADO System® blocks
CEADO... test connectors for ADO System® blocks

NFC VDE
Wire size Rigid 0,2 - 0,75 mm²

mm² Flexible 0,22 - 0,75 mm²
Voltage V (1)
Current A 6A (1) Rated voltage : 250 V for CEADO.5
Short circuit current (M 4/6.PI) A/s 400 V for CEADO.6
Rated wire size mm² / AWG 500 V for CEADO.8
To perform simple tests quickly :

This connector completes the range of modular connectors to be mounted on terminal block assembly.
Contact is made on top of the ADO jaw.
Hooking is made on the wire input of terminal blocks.
It can be achieved without modifying the assembly.
Selection
5, 6
or 8 mm
kg
Unit connector 1 pole black CEADO.5 5 mm 1SNA 399 345 R1100
End module black CEADOE 1SNA 399 341 R1500
Accessories
Assembly rod for levers DIA. 3 mm TGA3.156 156 mm 1SNA 206 277 R1400
End module
Markers RC 55 see section on markers
This end module is the same for
RTM
any unitary module
spacing : 5, 6 or 8 mm.
Building a test connector
N CEADO... modules
All modules joint together using

dog points. A connector can be
J made of 20 poles max.
The assembly rod for levers
(TGA3.156) cut at the convenient
5
length is advised for connectors
> 5 poles.
522
160T11011 051129

Test devices
Test plugs
Test sockets
FC... test plugs

These accessories, when used with measuring or control equipment, are used for trouble shooting or testing of a circuit, on the blocks
equipped with a test socket or by use of a test device (for FC2 only).
Selection
FC2 Description Type Order P/N Packaging Weight
kg
Test plug DIA. 2 mm .079" - Soldered
connection : 1 mm² max. - 18 AWG FC2 1SNA 007 865 R2600
connection : 1 mm² max. - 18 AWG FC2.EI.PJP 1SNA 107 239 R0300
connection : 1,5 mm² max. - 16 AWG FC4 1SNA 167 860 R0100
FC2.EI.PJP
AL... test sockets

This accessory is screwed into the tapped holes of the connector bar of the terminal blocks. Some blocks are delivered socket mounted.
This socket receives an FC test plug. The test sockets are characterized by their internal diameter.
FC4
Selection

kg
Test socket DIA. 2 mm .079"
H = 12 mm .472" - M3 screw AL2 1SNA 163 043 R2100
H = 11,7 mm .461" - M2,6 screw AL2 1SNA 163 046 R2400
H = 8,5 mm .335" - M3 screw AL2 1SNA 163 070 R0000
H = 8,5 mm .335" - M2,6 screw AL2 1SNA 167 319 R0600
AL... H = 12 mm .472" - M3 screw AL4 1SNA 163 240 R1700
DC... test device on screw head

This patented device is mounted on the round screwdriver opening. It is used for trouble shooting, measuring and control for monitoring and
repairing an installation, on blocks without a test socket. For this, the device receives an FC2 test plug.
Selection
J
kg
Test device for blocks with 5 mm
5
spacing green DCV 1SNA 173 058 R0200
Test device for MA 2,5/5 blocks
blue DCB 1SNA 105 028 R2100
DCJ spacing yellow DCJ 1SNA 173 059 R0300
Test device for M4/6.D and MB 2,5/6
blocks grey DCG 1SNA 163 218 R0500
spacing orange DCO 1SNA 173 060 R0000
523
160T11077 051129

Other accessories
PC... + EIP comb-type jumper bar + insulating tip

This accessory can be used only on the terminal blocks with at least one compression clamp connection. It permits the electrical connection
of 2 to 10 blocks.
Interconnection of non-consecutive blocks is possible by removing the teeth opposite the blocks which must not be connected. The comb-
type jumper bars can be cut using pliers (or a saw) : in this case, the use of an insulating tip EIP is recommended where possible ; otherwise,
use an SCF separator or FE end section between two series of interconnected blocks, in order to preserve insulation. The comb is placed in
the compression clamp before tightening the screws, above the eventual conductor.
Selection
Insulating tip for comb Comb-type jumper bar
To be mounted on blocks Type Order P/N Nb of poles Type Order P/N Current
MA 2,5/5... EIP 1SNA 113 550 R2400 2 PC5 1SNA 113 542 R1000 30 A
MA 2,5/5.D... 10 PC5 1SNA 113 544 R1200 30 A
DR 1,5/5... 10 PC51 1SNA 167 908 R0600
M 4/6 - MS 4/6 - M 4/6.H EIP 1SNA 113 550 R2400 2 PC6 1SNA 113 546 R1400 35 A
M 1,5/6.HH - M 4/6.M2 3 PC6 1SNA 116 536 R0500 35 A
M 4/6.G 4 PC6 1SNA 116 537 R0600 35 A
PC... + EIP 10 PC6 1SNA 113 548 R2600 35 A
M 4/6.D - M 4/6.S... 10 PC61 1SNA 163 311 R2200 35 A
DR 4/6 - DR 2,5/6 - DRP 4/6
M 6/8 - M 6/8.S... 2 PC8 1SNA 116 538 R1700 50 A
3 PC8 1SNA 116 539 R1000 50 A
4 PC8 1SNA 116 540 R2500 50 A
10 PC8 1SNA 163 313 R2400 50 A
M 4/8.S... 10 PC81 1SNA 173 523 R1100 35 A
M 10/10 10 PC10 1SNA 163 315 R2600 70 A
M 10/13.S... 10 PC13 1SNA 173 510 R2000 70 A
MB 10/22.S... 2 PC22 1SNA 205 294 R0500 70 A
3 PC22 1SNA 205 295 R0600 70 A
10 PC22 1SNA 174 151 R2500 70 A
M 10/16.SF EIP 1SNA 113 550 R2400 2 PC16 1SNA 116 729 R2600 70 A
3 PC16 1SNA 116 733 R1200 70 A
4 PC16 1SNA 116 734 R1300 70 A
10 PC16 1SNA 116 735 R1400 70 A
Series 7000 or 8000 10 PC9 1SNA 210 160 R1200 15 A
IDC jumper (insulation displacement jumper)

NFC VDE
Wire size Rigid 2,5 mm²

14 AWG
mm² / AWG Flexible 2,5 mm²
Voltage V 600 600
Current A 26 15
2
Rated wire size mm² / AWG 2,5 mm 14 AWG
Working temperature °C -55°C -> +110°C
AD 2,5
Protection IP20 / NEMA1
Quick-jump lets you interconnect screw clamp terminals of different sizes, levels and all manufacturers quickly and safely. Its insulation
displacement technology makes it easy to use, fast, economical and does not require a special tool. Use as a jumper between relays,
switches and other electronic components. ABB Entrelec Quick-jump will fit any screw clamp type terminal block, from 6 mm .238" spacing
and larger.
Selection
kg
J 3
Insulation displacement jumper AD 2,5 1SNA 114 205 R2000
4
2
6 How to use : connecting Quick-jump to your terminal
1- Insert Entrelec Quick-jump into your terminal screw clamp.

1 2- Tighten the terminal screw.
3- Guide jumper wire through the V-shaped opening in the Quick-jump.
4- Secure the wire by closing the Quick-jump lever with any flat nose pliers.
4
Adding a shunt in an installation :
3
1- Insert Entrelec Quick-jump into your terminal screw clamp.

2- Guide the terminal screw clamp into contact with the wire.
1 3- Secure the wire by closing the Quick-jump lever with any flat nose pliers.
2 4- Tighten the terminal screw.
524
160T11083 051129

Other accessories
EL... connector plate

This accessory is used for connecting electrically : two assembled interconnections with same spacing or two assembled interconnections
with different spacings. Use only between the 5 mm .200" spacing, 6 mm .238" spacing and 8 mm .315" spacing blocks.
EL...
Current carrying capacity : 35 A
Selection
kg
Connector plate EL6 1SNA 173 627 R2100
Connector plate for D 2,5/6.D... blocks EL61 1SNA 177 812 R1700
BJP... pivoting jumper bar

This accessory is for connecting or disconnecting two consecutive blocks, open or closed. The use of a third non-connected is
recommended, to allow for a "rest" position of the rotating jumper link. We recommend the use of a circuit separator SC in order to preserve
the insulation. The BJP is mounted in the center of the terminal blocks, the connector bars of which are tapped for receiving the
interconnection accessories. Max. recommended torque : 0,6 Nm.
Selection
Pivoting jumper bar for blocks with
6 mm .238’’ spacing BJP6 35 A 1SNA 174 413 R1400
Pivoting jumper bar for double deck
blocks with 6 mm .238’’ spacing BJP61 35 A 1SNA 167 225 R2000
Pivoting jumper bar for double deck
blocks with 8 mm .315’’ spacing BJP82 50 A 1SNA 163 169 R0400
Pivoting jumper bar for DR 4/6...
blocks BJPD6 35 A 1SNA 173 223 R2400
BJP...
BP8.A4 bridging plug

This accessory permits electrical connection of 2 identical juxtaposed blocks. These blocks have 8 mm / .315" spacing, are equipped with a
test socket DIA. 4 mm / .16".
Selection
BP8.A4 Bridging plug BP8.A4 1SNA 173 888 R2000
BNSTP1 short-circuiting plug

Shunt equipped with 2 plugs DIA. 4 mm/.16" for ES16 and M6/8.STP... blocks and one test socket DIA. 4 mm/.16".
Rated voltage : 600 V Rated current : 20 A .
Selection
BNSTP1 Short-circuiting plug light ivory BNSTP1 1SNA 196 792 R1700
CB... shield connector

Delivered separately, this bar of treated brass is mounted in the lower part of the terminal block. It ensures the continuity of the shield
connection. The connection to the shield connector can be made either by soldering or by 2,8 x 0,5 mm or 2,8 x 0,8 mm quick connect tabs.
Notch available for bridging all shieldings. This accessory overlaps on each side of the block by about 13,5 mm.
J
Use of this bar reduces insulation between terminal and ground, working voltage must be derated (consult us if necessary).
6
Selection
Shield connector CBD5.2L 1SNA 291 077 R2400
CBM5D 1SNA 173 530 R2400
CBD2S 1SNA 178 408 R1400
CB... CBD2 1SNA 179 635 R0700
CBD1 1SNA 179 634 R0600
CBM8 1SNA 178 746 R1500
CBM5 1SNA 178 745 R1400
525
160T11084 051129

Tools
Screwdriver
Screwdriver
Description Type O r d er P / N Packaging Weight
kg
Screwdriver DIA. 3.5 mm .137" 030 411 423 kg
Screwdriver DIA. 3 mm .118" 1SNA 206 573 R0500
Screwdriver
Screwdriver
EXBN2 extraction
EXBN2 extraction tool tool
Extraction tool for plug type disconnect terminal blocks.
Extraction tool EXBN2 1SNA 171 018 R2000

Extraction tool for plug type disconnect terminal blocks.
EXBN2
Extraction tool EXBN2 1SNA 171 018 R2000

EXBN2
Ferrule crimping tools Screwdrivers
All purpose economy crimping tool.
Ferrule wire range P/N
0305 626.05 22 to 10 AWG 0305 626.05

10 to 6 AWG 0305 627.06
Heavy duty industrial grade

crimping tool.
Ferrule wire range P/N
0304 441.03 8 to 1 AWG 0304 441.03
Wire stripping tool

Wire strip range P/N
20 to 10 AWG XUS0 003.71
Fast and easy-to-operate wire stripper

that needs no adjustment and will not
damage solid or stranded wire. Ideal
A (mm) B (mm) C (mm)
for use in any control or low voltage
Shaft Length Tip Width Tip Cross Section
wire stripping applications for wire
65 2.0 0.4
sizes from 20 AWG to 10 AWG
100 3.5 0.6
(0.5 mm2 to 6 mm2). Stripping blades
125 5.5 1.0
XUS0 003.71
are replaceable with expected
150 6.5 1.2
operating life in excess of 100,000
operations. Includes wire cutter and
adjustable wire stop for consistent Tip Width, mm P/N
length of stripping.
Package of 4 0101 695.27
J Screwdrivers
are configured to
facilitate connect and
7 disconnect of wire in screw clamp
terminal blocks. Nonbreakable tip for
long life. Tapered shank and rotating
top provides operator comfort during
repetitive use. Designed for precise
screw slot fit for all screw clamp
terminal block connections.
Screwdrivers may be ordered
separately or as a package of four (4).
526
160T11086 051129

Notes
527
NOTE_527 060529

528

Terminal Blocks: J - Accessories

Uploaded by

Copyright:

Available Formats

Terminal Blocks: J - Accessories

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Terminal Blocks: J - Accessories

Uploaded by

Copyright:

Available Formats

160TJ001 060220

1. Mounting rails .................................................................................................................. 506

2. End stops ......................................................................................................................... 508

3. Circuit separators, seperator end sections .................................................................. 512

Screw clamp jumper bars ..................................................................................................... 514

Test connectors ..................................................................................................................... 521

Comb-type jumper bars, insulation displacement jumper ................................................... 524

7. Tools .................................................................................................................................. 526

Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected]

Mounting rails TS 35/F6 TS 35

These rails are often used as grounding

RAIL CURRENT CARRYING CAPACITY

TS 35/S TS 35 Aluminum Rail TS 35 Copper Rail

In compliance with EN 50022 standard

1012468_alts.indd 5 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 9:17:43 AM

TS 35/CF6 TS 35/C1 TS 35/C

Zinc bichromate plated steel, length Prepunched aluminum anode-yellow alloy

Rail offset brackets

Insert for rail knockout: Insert for rail knockout:

Sold in North America only. Sold in North America only.

Deflection 90° Deflection 45°

Symmetrical type 2 reinforced

1012468_alts.indd 6 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 8:06:39 AM

Description Type Order P/N Packaging Weight

The “Series DR” terminal blocks snap

These rails are often used as BAM2

(1) For BADL only

1012468_alts.indd 7 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 8:06:45 AM

Tall end stop BADH, BAEH

Description Type Order P/N Packaging Weight

Description Type Order P/N Packaging Weight

1012468_alts.indd 8 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 8:06:49 AM

Description Type Order P/N Packaging Weight

Description Type Order P/N Packaging Weight

Description Type Order P/N Packaging Weight

1012468_alts.indd 9 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 8:06:53 AM

Tall end stop BADH, BAEH

Description Type Order P/N Packaging Weight

Épaisseur : 10 mm .394" Épaisseur : 10 mm .394"

Description Type Order P/N Description

Description Type Order P/N Packaging Weight

Markers PEBM (2)

510 510 511

1012468_alts.indd 10 Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected] 9/28/06 8:06:56 AM

Product Type Order P/N Product Type Order P/N

CPM + RTC CPM width : 32 mm 1.26"

Protective cover clear CPM 1SNA 187 312 R1400

This marker holder snaps on separator end sections SCF or

Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected]

Product Type Order P/N Product Type Order P/N

With possibility of mounting a protective cover CPV, and a

This marker holder snaps on separator end section SCFCV.

Gross Automation (877) 268-3700 · www.entrelecsales.com · [email protected]

IP20 assembled screw jumper bars

Max. recommended torque : 0,6 Nm

Description Type Order P/N Packaging Weight

Max. recommended torque : 0,6 Nm

Description Type Order P/N Packaging Weight

76 A - 2 poles BJMI12 1SNA 179 626 R0600