Scribd Logo
Upload

Welcome to Scribd!

  • 174 views

    Heienhain TNC 407: Ncnet 7.0 Settings

    Uploaded by

    Alejandro
    This document provides settings and connection instructions for configuring a Heidenhain TNC 407 controller and PC for communication using an NCnet 7.0 protocol over a serial port. It includes parameters to set on the machine and PC, as well as cable wiring diagrams for null modem or full handshake connections between the PC and machine's 9-pin or 25-pin serial ports. Drip feed mode is noted as not being available on this controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Heienhain TNC 407: Ncnet 7.0 Settings

    Uploaded by

    Alejandro
    174 views2 pages
    This document provides settings and connection instructions for configuring a Heidenhain TNC 407 controller and PC for communication using an NCnet 7.0 protocol over a serial port. It includes parameters to set on the machine and PC, as well as cable wiring diagrams for null modem or full handshake connections between the PC and machine's 9-pin or 25-pin serial ports. Drip feed mode is noted as not being available on this controller.

    Original Title

    Heidenhain-407

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides settings and connection instructions for configuring a Heidenhain TNC 407 controller and PC for communication using an NCnet 7.0 protocol over a serial port. It includes parameters to set on the machine and PC, as well as cable wiring diagrams for null modem or full handshake connections between the PC and machine's 9-pin or 25-pin serial ports. Drip feed mode is noted as not being available on this controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    174 views2 pages

    Heienhain TNC 407: Ncnet 7.0 Settings

    Uploaded by

    Alejandro
    This document provides settings and connection instructions for configuring a Heidenhain TNC 407 controller and PC for communication using an NCnet 7.0 protocol over a serial port. It includes parameters to set on the machine and PC, as well as cable wiring diagrams for null modem or full handshake connections between the PC and machine's 9-pin or 25-pin serial ports. Drip feed mode is noted as not being available on this controller.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Heienhain TNC 407

    NCnet 7.0 settings

    Set these parameters on the machine

    DEVICE = EXT 2
    MP 5200.1 = 2 (External device)
    MP 5201.1 = 3 (External device)
    MP 5020.1 = 104
    MP 5030.1 = 0

    To set the controller in the Drip-feed mode


    Drip feed is not available on this controller.

    Set these parameters on the PC

    Machine details

    Machine name MCH-1


    Control system Heidenhain
    Machine ID 01
    Communication Channel Serial Port
    Port Number Any free COM port
    Folder for PC to Machine transfer Transmit directory
    Folder for Machine to PC transfer Receive directory
    Baud rate 2400
    Data bits 7
    Parity Even
    Stop bits 2
    Handshake Hardware

    General settings
    Ignore this. Leave all data as it is.

    Transmit settings

    Wait period at start of transmission 10.00


    Wait period after transmitting program 5.0
    Size of transmit packet 0
    Delay period after each packet 0
    Wait for XON before transmitting program No
    Transmit comments? Yes
    Comment start character (
    Comment end character )
    Translation mode for CR Transmit as CR
    Translation mode for LF Transmit as LF
    Acknowledgement and error (Mode of transmission) Transmit descriptive message
    ACK/ERR Message start text %1234G71G50
    ACK/ERR Message start text M30
    %1234G71G50
    Filter Null Character Yes
    NC Program settings

    Page 1 of 2
    Program start string
    Program end string
    Characters to transmit at start Number of Characters
    Characters to transmit at start Number of Characters

    Receive settings

    Wait period before receiving program 45.0


    Wait period after receiving program 5.0
    Transmit XON before transmitting program No
    Auto compare and save Yes
    Acknowledgements and errors Transmit descriptive messages
    Translation mode for CR Ignore
    Translation mode for LF Save as CRLF
    Ignore control characters other than CR-LF Yes
    Save Program between Start Characters and End Characters No
    Start Program reception after these characters are received
    End Program reception after these characters are received

    To set the PC in the Drip-feed mode


    Drip feed is not available on this controller.

    Cable connections

    If the PC has 9 pin connector

    Null modem Full Handshake


    PC CNC PC CNC
    9 pin 25 pin 9 pin 25 pin

    1 8 1 8
    2 2 2 2
    3 3 3 3
    4 20 4 6
    5 7 5 7
    6 6 6 20
    7 4 7 5
    8 5 8 4

    If the PC has 25 pin connector

    Null modem Full Handshake


    PC CNC PC CNC
    25 pin 25 pin 25 pin 25 pin

    8 8 8 8
    2 3 2 3
    3 2 3 2
    20 20 20 6
    7 7 7 7
    6 6 6 20
    4 4 4 5
    5 5 5 4

    Page 2 of 2

    You might also like