Takeuchi TB175 Operator's Manual PDF

TB175
TB175
Hydraulic Excavator
OPERATOR’S MANUAL
Serial No. 17512105~

Book No. AL3E016
OPERA TOR’S MANUAL
WARNING
Read and understand these instructions.
Failure to do so can cause injury or death.
E
Downloaded from www.dlmanuals.com
SAFETY ALERT SYMBOL
This symbol means Attention! Be Alert! Your Safety Is Involved.
The message that follows the symbol contains important information
about safety.
Read and understand the message to avoid personal injury or death.
■ It is the owner or employer’s responsibility to fully instruct each operator in the

proper and safe operation of all equipment. All persons using this machine should
thoroughly familiarize themselves with the following sections.
■ All operators must be instructed on the proper functions of the excavator before
running the machine.
■ Learn and practice correct use of the machine controls in a safe, clear area before
operating this machine on a job site.
CAUTION
Improper operation, inspection and maintenance of this

machine can cause injury or death.
Read and understand this manual before performing any
operation, inspection or maintenance on this machine.
■ Always store this manual near at hand preferably on the machine itself. If it should be lost
or damaged, immediately order a new one from your Takeuchi dealer.
When transferring ownership of this machine, be sure to provide this manual to the next
owner.
■ Takeuchi supplies machines complying to the local regulations and standards of the country
of export. If your machine has been purchased in another country or from a person or
company of another country, it may not have the safety devices or safety standards required
for use in your country. Should you have any question about whether your machine complies
with the regulations and standards of your country, contact a Takeuchi dealer.
■ Please note that the contents and diagrams included in this manual may not match your
machine exactly.

CALIFORNIA
Proposition 65 Warning
Diesel engine exhaust and some of its constituents are
known to the State of California to cause cancer, birth
defects, and other reproductive harm.
Battery posts, terminals and related accessories contain lead
and lead compounds, chemicals known to the State of
California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling battery.

It is your responsibility to observe all pertinent laws and regulations and to follow the
manufacturer’s instructions on machine operation, inspection and maintenance.
Virtually all accidents occur as the result of a failure to observe basic safety rules and
precautions. An accident can often be avoided by recognizing potentially hazardous situations
beforehand. Read and understand all of the safety messages which explain how to prevent
these accidents from occurring. Do not operate the machine until you are sure that you have
gained a proper understanding of its operation, inspection and maintenance.
■ SlGNAL WORDS
Safety messages appearing in this manual and on machine decals are identified by the
words “DANGER”, “WARNING” and “CAUTION”. These signal words mean the following:
DANGER WARNING CAUTION

The word “DANGER” The word “WARNING” The word “CAUTlON”
indicates an imminently indicates a potentially indicates a potentially
hazardous situation hazardous situation hazardous situation
which, if not avoided, which, if not avoided, which, if not avoided,
can result in serious could result in serious may result in minor or
injury or death. injury or death. moderate injury.
IMPORTANT: The word “IMPORTANT” is used to alert against operators and

maintenance personnel about situations which can result in possible damage to the
machine and its components.
It is impossible to foresee every possible circumstance that might involve a potential hazard.
The warnings in this manual or on the machine can not cover all possible contingencies. You
must exercise all due care and follow normal safety procedures when operating the machine
so as to ensure that no damage occurs to the machine, its operators or other persons.
■ EXPLANATION OF GRAPHICAL SYMBOLS

Following is an explanation of symbols used in this manual.
, X ......... prohibition
/ ....... Lock
/ ...... Unlock
1
INTRODUCTION
Foreword
This manual describes operation, inspection
and maintenance of the machine, as well as
safety instructions to be heeded during these
operations.
If you have any questions about the machine,
please contact a Takeuchi sales or service
outlet.
■ Manual storage compartment ■ Serial numbers

A compartment for storing this manual is Check the serial numbers of the machine and
provided at the position shown on the the engine and write them in the spaces
diagram below. provided below.
Machine number :
L3A001
1. Open the cover behind the seat. N0A002

2. After using the manual, place it in the
plastic pouch and store it back in the
manual storage compartment. Engine number :
2
MACHINE DESCRIPTlON
■ Front, rear, Ieft and right

FRONT
This manual refers the front, rear, left and
right of the machine as seen when sitting in
the operator’s seat with the dozer blade
Dozer blade
visible to the front.
■ Designated operations
Use this machine primarily for the following LEFT RIGHT
operations:
¡ Excavating
¡ Digging ditches
¡ Digging side ditches
¡ Leveling
¡ Loading REAR
E3A020
■ Features
¡ Automatic travel shift-down system.
¡ Isolation mounted cab minimizes vibration.
¡ Short pitch rubber crawler.
¡ Low engine noise and exhaust emissions.
¡ Electro over hydraulic control of auxiliary hydraulic circuit.
¡ One touch engine deceleration button.
¡ Two-speed slew allows the operator to slow the excavators slew speed.
¡ Engine emergency stop/idle system.
¡ Self-adjusting hydraulic crawler tension system.
¡ Travel motor are equipped with shock less valves for smooth starts and stops.
■ Break-in period
When the machine is new, heed the instructions below when operating the machine for the
first 100 hours (as indicated on the hour meter).
Using a new machine roughly without breaking it in will lead to quicker deterioration of machine
performance and may shorten the machine’s service life.
¡ Warm up the engine and hydraulic oil sufficiently.
¡ Avoid heavy loads and rapid operations. Operate with a load of about 80% the maximum
load.
¡ Do not start up, accelerate, change directions, or stop abruptly unless necessary.
3
4
CONTENTS
Introduction .................................... 2
Machine Description ...................... 3
Safety .............................................. 7
Controls .........................................35
Operation .......................................63
Transport .......................................91
Maintenance ..................................95
Troubleshooting .......................... 141
Specifications .............................. 155
Options ........................................ 181
Index ............................................ 221
5
6
SAFETY
General precautions .................................... 8
Preparing precautions ............................... 12
Starting precautions .................................. 14
Operating precautions ............................... 16
Stopping precautions ................................ 23
Transporting precautions .......................... 24
Maintenance precautions .......................... 25
Safety signs (Decals) ................................. 32
7
SAFETY
General Precautions
Observe all safety rules Wear appropriate clothing and

personal protective equipment
¡ Operation, inspection and maintenance of
this machine must be performed only by
a trained and qualified person.
¡ All rules, regulations, precautions and
safety procedures must be understood
and followed when performing operation,
inspection and maintenance of this
machine.
¡ Do not perform any operation, inspection
and maintenance of this machine when
under the adverse influence of alcohol, ¡ Do not wear loose clothing or any
drugs, medication, fatigue, or insufficient accessory that can catch on controls or in
sleep. moving parts.
¡ Do not wear oily or fuel stained clothing
that can catch fire.
¡ Wear a hard hat, safety shoes, safety
glasses, filter mask, heavy gloves, ear
protection and other protective equipment
as required by job conditions. Wear
required appropriate equipment such as
safety glasses and filter mask when using
grinders, hammers or compressed air, as
metal fragments or other objects can fly
and cause serious injury.
¡ Use hearing protection when operating the
machine. Loud prolonged noise can cause
hearing impairments, even the total loss
of hearing.
8
SAFETY
General Precautions
Provide a fire extinguisher and Use a signal person and flagman

first aid kit
Know and use the hand signals required for

¡ Know where a fire extinguisher and first particular jobs and make sure who has the
aid kit are located and understand how to responsibility for signaling.
use them. ¡ All personnel must fully understand all the
¡ Know how to contact emergency signals.
assistance and first aid help. ¡ The operator shall respond to signals only
from the appointed signal person, but shall
obey a stop signal at any time from
anyone.
¡ The signal person must stand in a clearly
visible location when giving signals.
Never remove safety equipment

¡ Make sure all protective guards, canopies,
doors, etc., are in place and secure. Repair
or replace damaged components before
operating the machine.
¡ Know how to use the safety lock lever, seat

belt and other safety equipment and use
them properly.
¡ Never remove any safety equipment
except for service. Keep all safety
equipment in good operating condition.
9
SAFETY
General Precautions
Be sure to lock the safety lock Avoid fire and explosion hazards
lever before leaving the
operator’s seat
Keep flames away from fuel, hydraulic fluid,

oil, grease and antifreeze. Fuel is particularly
¡ Before leaving the operator’s seat, raise flammable and dangerous.
the safety lock lever to engage the lock ¡ When handling these combustible
and stop the engine. If any controls should materials, keep lit cigarettes, matches,
be touched accidentally when the safety lighters and other flames or sources of
lock lever is lowered, the machine will flames away
move suddenly, and cause serious injury ¡ Do not smoke or permit open flames while
or death. fueling or near fueling operations.
¡ Note that the dozer blade control is not ¡ Never remove the fuel cap or refuel with
locked, even when the safety lock lever is the engine running or hot. Never allow fuel
set to the lock position. Do not touch this to spill on hot machine components.
control accidentally. ¡ Clean up spilled fuel, oil or other
¡ Before leaving the operator’s seat, lower flammable fluids immediately.
the working equipment, raise the safety ¡ Check for fuel, oil or hydraulic fluid leaks.
lock lever to engage the lock, and stop Stop all leaks and clean the machine
the engine. Also, be sure to remove the before operating.
key and take it with you. ¡ Do not cut or weld on pipes or tubes that
contain flammable fluids. Clean thoroughly
with nonflammable solvent before cutting
or welding.
¡ Remove all trash or debris from the
machine. Make sure that oily rags or other
flammable material are not stored on the
machine.
¡ Handle all solvents and dry chemicals
according to procedures identified on
manufacturers’ containers. Work in a well-
ventilated area.
¡ Never use fuel for cleaning purposes.
Always use a nonflammable solvent.
¡ Store all flammable fluids and materials
in a safe and well-ventilated place.
10
SAFETY
General Precautions
Exhaust fumes from the engine Be careful not to get crushed or

can kill cut
¡ Do not operate the engine in an enclosed Never put your hands, feet or other parts of
area without adequate ventilation. your body between the upperstructure and
¡ If natural ventilation is poor, install the undercarriage or tracks, between the
ventilators, fans, exhaust extension pipes machine body and working equipment, or
or other artificial venting devices. between a cylinder and moving part. The size
of these gaps change when the machine
moves and if caught a person can suffer
severe injury or death.
Handling asbestos dust Using optional products

Inhaling asbestos dust has been linked to ¡ Consult with a Takeuchi dealer before
lung cancer. When handling materials which installing optional attachments.
may contain asbestos, take the following ¡ Do not use attachments that have not
precautions: been approved by Takeuchi or a Takeuchi
¡ Never use compressed air for cleaning. dealer. Doing so may compromise safety
¡ Avoid brushing or grinding of the materials. or adversely affect the machine’s
¡ For clean up, use wet methods or a operation or service life.
vacuum equipped with a high efficiency ¡ Takeuchi will not be held responsible for
particulate air (HEPA) filter. any injuries, accidents or damage to its
¡ Wear an approved respirator if there is no products caused by the use of a non-
other way to control the dust. When approved attachment.
working indoors, install a ventilation
system with a macro molecular filter.
Never modify the machine
Unauthorized modifications to this machine
can cause injury or death. Never make
unauthorized modifications to any part of this
machine.
11
SAFETY
Preparing Precautions
Know the working area Alway keep the machine clean

Before starting operation, know the working
area to ensure safety.
¡ Check the topography and ground
condition of the working area, or the
structure of the building when working
indoors, and take the necessary safety
measures in dangerous spots.
¡ Note and avoid all hazards and
obstructions such as ditches, underground
lines, trees, cliffs, overhead electrical wires ¡ Clean windows, mirrors and lights to
or areas where there is danger of a slide. ensure good visibility.
¡ Wipe off any oil, grease, mud, snow or
ice, to prevent accidents due to slipping.
¡ Remove all loose objects stored in the
machine and all objects which do not
belong in or on the machine and its
equipment.
¡ Remove any dirt, oil or grease from the
engine area, to prevent fires.
¡ Clean the area around the operator’s seat,
removing any potential obstacles.
¡ Check with the local utilities for the
locations of buried gas and water pipes
and buried power cables. Determine jointly
what specific precautions must be taken
to insure safety.
¡ When working on roads, be sure to take
into account the safety of pedestrians and
vehicles.
• Use a flagman and/or signals.
• Fence off the working area and prohibit
entry to unauthorized persons.
¡ When working in water or crossing shallow
streams or creeks, check the depth of the
water, the solidity of the ground, and the
speed of the current beforehand. Make
sure the water is not deeper than the
allowable depth.
Refer to the section titled “Cautions on
Operating” for further instructions.
12
SAFETY
Preparing Precautions
Perform inspection and

maintenance daily
Failure to notice or repair machine

irregularities or damage can lead to
accidents.
¡ Before operating, perform the prescribed
inspections and make repairs immediately
should any irregularities be found.
¡ If a failure that causes loss of control such
as steering, service brakes or engine
occurs, stop the machine motion as
quickly as possible, follow the shutdown
procedure, and keep machine securely
parked until the malfunction is corrected.
13
SAFETY
Starting Precautions
Maintain three point contact Clear the area of other persons

when mounting and dismounting before starting the machine
¡ Do not jump on or off the machine. Never Do not start the engine until you are sure it is
attempt to mount or dismount a moving safe. Before starting, check or perform the
machine. following.
¡ When mounting and dismounting the cab, ¡ Walk around the machine and warn all
first open the door fully to the locked personnel who may be servicing the
position and check that it does not move. machine or are in the machine path. Do
(For machines with cabs) not start until all personnel are clearly away
from the machine.
¡ Check for any “DO NOT OPERATE” tags
or similar warning notices on the cab door,
controls or starter switch.
¡ Sound horn to alert everyone around the
machine.
Start the engine from the

¡ Always face the access system and operator’s seat
maintain a three point contact with the
recommended handrails and steps while ¡ Adjust, secure and latch the operator’s
getting on and off the machine. Keep steps seat.
and platform clean.
¡ Never use the safety lock lever or control
levers as hand holds.
¡ Fasten the seat belt.

¡ Check that the parking device is applied
and place all controls in the neutral
position.
¡ Check that the safety lock lever is in the
lock position.
¡ Clear the area of all persons.
¡ Start and operate the engine from the
operator’s seat only.
¡ Never attempt to start the engine by
shorting across the starter terminals.
14
SAFETY
Starting Precautions
Starting with jumper cables In cold weather
Use jumper cables only in the recommended ¡ Be careful of slippery conditions on

manner. Improper use of jumper cables can freezing ground, steps and hand holds.
result in battery explosion or unexpected ¡ In severe cold weather, do not touch any
machine motion. metal parts of the machine with exposed
Refer to the section titled “If the Battery flesh, as flesh can freeze to the metal and
Goes Dead” for proper instructions. Cause injury.
¡ Do not use ether or starting fluids on this
engine. These starting aids can cause
explosion and serious injury or death.
¡ Warm up the engine and hydraulic fluid
before operating.
After starting the engine

After starting the engine, perform the
following operations and checks in a safe
place with no persons or obstacles in the
area. If any malfunctions are found, follow
the shutdown procedure and report the
malfunction.
¡ Warm up the engine and hydraulic fluid.
¡ Observe all gauges or warning
instruments for proper operation.
¡ Listen for unusual noises.
¡ Test engine speed control.
¡ Operate each control to insure proper
operation.
15
SAFETY
Operating Precautions
Ensure good visibility Check for safety in the

surrounding area before starting
¡ When working in dark places, turn on the
machine’s working lights and headlights
and/or provide extra stationary lighting if
necessary.
¡ When visibility is poor due to severe
weather (fog, snow or rain), stop operating
the machine and wait until conditions
improves.
¡ Understand the machine limitations.

¡ Use a signal person where clearances are
close or your vision is obstructed.
Do not permit riders on the ¡ Never allow anyone to enter the slewing
machine (swing) radius and machine path.
¡ Signal your intention to move by sounding
the horn.
¡ There are blind spots to the rear of the
machine.
If necessary, swing the cab around before
backing up to check that the area is safe
and clear.
¡ Do not allow anyone to ride on any part of

the machine at any time while traveling.
¡ Do not allow anyone to be on any part of
the machine while operating.
16
SAFETY
Check the position of the ¡ Do not slew (swing) while traveling. If you
must operate the hoe attachment while
undercarriage (tracks) before
traveling, operate at speeds slow enough
traveling so you have complete control at all times.
¡ When a load greater than a set value is
applied during 2nd speed (high speed)
travel, the speed will automatically slow
down by switching to 1st speed (low
speed). Thereafter, when the load
becomes lighter, the speed will increase
by returning to 2nd speed (high speed).
Exercise due caution since the travel
speed changes automatically.
Before operating the travel levers, check to
make sure that the dozer blade is to the front
of the operator’s seat. BE AWARE that when
the dozer blade is to the rear of the operator’s
seat, the travel levers operate in the opposite
direction to when the dozer blade is in the
front.
E4A040
¡ Avoid crossing over obstacles whenever

Travel safety possible. If you must do so, keep the hoe
attachment close to the ground and travel
slowly. Never cross obstacles if they will
seriously tilt the machine (to an angle of
10° or greater).
¡ On uneven ground, travel at low speed
and avoid accelerating, stopping or
changing directions abruptly.
¡ When roading a machine, know and use
(12 to 16 in.)
the signaling devices required on the
¡ Travel with the dozer blade up, the hoe machine. Provide an escort for road travel
attachment folded as shown on the when required.
diagram, and the bucket raised 30 to 40
cm (12 to 16 in.) from the ground.
¡ Note that when the bucket is operated
while making a right pivot turn (i.e., when
only the left crawler is turning), the speed
of the pivot turn may suddenly increase.
17
SAFETY
Cautions on traveling on slopes

When traveling on slopes or grades, be
careful that the machine does not tip (roll)
over or slide.
¡ Never exceed the machine’s stability
capabilities (maximum gradeability - 35°,
lateral tipping angle - 15°). Also note that
when actual working area conditions are ¡ Do not change directions or cross slopes
poor the machine’s stability capabilities sideways. First return to a flat surface then
may be lower. redirect the machine.
¡ When traveling on slopes or grades, lower Operate on snow or ice with

the bucket to a height of 20 to 30 cm (8 to
extra care
12 in.) off the ground. In emergencies,
lower the bucket to the ground and stop ¡ When traveling on snow or frozen
the machine. surfaces, keep the machine travel speed
¡ When traveling on slopes or grades, move down and avoid accelerating, stopping or
slowly in first gear (low speed). changing directions abruptly.
¡ Do not travel down slopes in reverse. ¡ Remember that the road shoulder, fences,
¡ On grass, dead leaves, wet metal or frozen etc., may be buried in the snow and not
surfaces, the machine may slide sideways visible.
even on very gentle slopes. Make sure ¡ Lower the dozer blade when parked on
the machine never faces sideways with unsure ground conditions.
respect to the slope.
18
SAFETY
Insure driver safety before ¡ Maintain the maximum possible distance

from power lines and never violate the
loading trucks
minimum clearance.
¡ Always contact the nearest electric utility
and determine jointly what specific
precautions must be taken to insure safety.
¡ Consider all lines to be power lines and
treat all power lines as energized even
though it is known or believed that the
power is shut off and the line is visibly
grounded.
¡ Use a signal person to observe the
Do not load a truck unless the driver is in a approach of any part of the machine or
safe place. load to the power line.
¡ Never swing or position the bucket over ¡ Caution all ground personnel to stand
personnel or truck cabs. clear of the machine and the load at all
¡ Load the truck from the rear. times.
¡ If the machine should come in contact with
a live electrical source, do not leave the
operator’s seat. Do not allow anyone to
approach or touch the machine.
Keep a safe distance from

electrical power lines
¡ Be especially careful of buried high voltage

power lines.
Never approach power lines with any part of

the machine and its load unless all local and
national required safety precautions have
been taken. Electrocution and death can
result from arcing, touching or even being
close to a machine that is in contact with or
near an electrical source.
19
SAFETY
Watch out for hazardous working • The ground is weak after rain or
explosions.
conditions
• The ground is also unstable on banks
and near dugout trenches.
Operating on slopes is
dangerous
When operating on slopes or grades, slewing
(swinging) or operating working equipment
¡ Never undercut a high bank. Be may cause the machine to lose stability and
particularly alert for the possibility of a tip over. Avoid operating on slopes whenever
cave-in. possible.
¡ Do not operate in places where there is a
danger of falling rocks.
Fill
¡ Level off the work area.
¡ Keep machine well back from the edge of

an excavation. Avoid undercutting the
machine.
¡ Avoid swinging the loaded bucket in a

downhill direction. This will reduce the
stability of the machine.
¡ Do not approach unstable surfaces (cliffs,

road shoulders, deep trenches, etc.). The
ground may give way under the machine’s
weight or vibrations, causing the machine
to tip over.
20
SAFETY
Never slew (swing) sideways with Excavators are not designed for
excessive weights lifting loads
The machine can tip over more easily in the The machine is specifically designed for
lateral direction than in the longitudinal excavation work and has no safety devices
direction. for crane operation. Extreme caution should
¡ Do not slew (swing) sideways with be used if the excavator is used for lifting.
excessive weight at the front. ¡ Never lift loads in excess of capacity.
In particular do not slew sideways on Overload will cause the machine to roll and
slopes. can result in serious injury or death.
¡ The front is heavier for machines equipped ¡ All rated lift capacities are based on the
with breakers, crushers or telescopic arms machine being level and on a firm
than for machines equipped with the supporting surface. For safe working
standard bucket. Do not operate such loads, the user is expected to make due
machines sideways especially with the allowance for the particular job conditions
digging arm (boom) downhill. such as soft or uneven ground, non-level
condition, side loads, dynamic or jerked
loads, hazardous conditions, experience
of personnel, etc. The operator and other
personnel should fully acquaint
themselves with the operator’s manual
Watch boom clearance
before operating this machine, and rules
for safe operation of equipment shall be
adhered to at all times.
¡ Failure of the bucket linkage or slings
could result if chains or slings are
incorrectly attached, resulting in serious
injury or death.
¡ Do not attempt to pull stumps out of the
ground while using the machine as a
crane. The loads imposed on the machine
When operating under bridges, in tunnels, under this use are completely unknown.
near power lines or indoors, be careful not ¡ Never allow any personnel to stand on or
to hit the boom or arm against overhead under lifted loads or even within the
objects. maneuvering area.
21
SAFETY
Danger of flying objects Cautions on Towing

This machine is not equipped with protective
guards to protect the operator from flying
objects. Do not use the machine in places
where there are risks of the operator being
hit by flying objects.
N0A006
When towing, selecting the wrong wire rope,

inspecting improperly, or towing in the wrong
way could lead to accidents resulting in
serious injury or death.
¡ The wire rope breaking or coming
detached could be extremely dangerous.
Use a wire rope suited for the required
towing force.
¡ Do not use a wire rope that is kinked,
twisted or otherwise damaged.
¡ Do not apply strong loads abruptly to the
wire rope.
¡ Use safety gloves when handling the wire
rope.
¡ Make sure there is an operator on the
machine being towed as well as on the
machine that is towing.
¡ Never tow on slopes.
¡ Do not let anyone near the wire rope while
towing.
22
SAFETY
Stopping Precautions
Park safely
E3A4901
¡ Park the machine on firm, level ground and

apply the parking device.
¡ When parking on streets, use barriers,
caution signs, lights, etc., so that the
machine can easily be seen even at night
to avoid collision with other vehicles.
¡ Before leaving the machine, do the

following:
1. Lower the bucket and dozer blade to
the ground.
2. Raise the safety lock lever to engage
the lock.
3. Stop the engine and remove the key.
4. Lock the cab and covers.
23
SAFETY
Transporting Precautions
Load and unload the machine Hoist the machine safely

safely
¡ Know and use correct crane signals.
¡ Inspect the hoisting equipment daily for
damaged or missing parts.
Fasten to the suspension fitting
¡ When hoisting, use a wire rope with
sufficient strength with respect to the
Ramp machine’s weight.
Stopper ¡ Do not hoist with the machine in a posture
other than the one described in the
Distance between ramps
15° or less
E4F001
procedure below. Doing so is dangerous
as it may result in the machine losing its
The machine may roll or tip over or fall while balance.
loading or unloading it. Take the following Refer to the section titled “Hoisting the
precautions: Machine” for further instructions.
¡ Select a firm, level surface and keep ¡ Do not hoist the machine with an operator
sufficient distance from road shoulders. (s) on it.
¡ Use loading ramps of adequate strength ¡ When hoisting, hoist slowly so that the
and size. Maintain the slope of loading machine does not tip.
ramps within 15 degrees. ¡ Keep all other persons out of the area
¡ Secure the ramps to the truck bed. when hoisting. Do not move the machine
¡ Keep the truck bed and loading ramps over the heads of the persons.
clean of oil, clay, ice, snow, and other
materials which can become slippery.
Clean the tracks.
¡ Block the transport vehicle so it can not
move. Transport the machine safely
¡ Use a signal person when loading and ¡ Know and follow the safety rules, vehicle
unloading the machine, and travel slowly code and traffic laws when transporting
in first gear (low speed). the machine.
¡ Never change course on the ramp. ¡ Consider the length, width, height and
¡ Do not slew (swing) on ramps. The weight of the truck with the machine
machine may tip over. loaded on it when determining the best
¡ When slewing (swinging) on the truck bed, route.
do so slowly as the footing can be
unstable.
¡ Engage the slew (swing) lock after loading.
¡ Block both tracks and secure the machine
to the truck bed with load binders.
24
SAFETY
Maintenance Precautions
Attach a “DO NOT OPERATE” tag Anti-explosive lighting

Severe injury could result if an unauthorized
person should start the engine or touch
controls during inspection or maintenance.
¡ Stop the engine and remove the key
before performing maintenance.
¡ Attach a “DO NOT OPERATE” tag to the
starter switch or control lever.
Use anti-explosive electrical fixtures and

lights when inspecting fuel, oil, coolant,
battery fluid, etc. If lighting that is not anti-
Use the correct tools
explosive should break, the substance could
ignite, resulting in serious injury or death.
Do not use damaged or weakened tools or

tools designed for other purposes. Use tools
suited for the operation at hand. Do not allow unauthorized
personnel in the work area
Replace important safety parts

periodically
¡ Replace fuel hoses periodically. Fuel
hoses become weaker over time, even if
they appear to be in good shape.
¡ Replace important safety parts whenever
an irregularity is found, even if it is before Do not allow unauthorized personnel in the
the normal time for replacement. work area. Chips or other debris can fly off
Refer to the section titled “Important Parts” machine parts when grinding, welding or
for further details. using a hammer.
25
SAFETY
Prepare the work area Stop the engine before

performing maintenance
¡ Select a firm, level work area. Make sure
there is adequate light and, if indoors, ¡ Avoid lubrication or mechanical
ventilation. adjustments with the machine in motion
¡ Clear obstacles and dangerous objects. or with the engine running while stationary.
Eliminate slippery areas. ¡ If maintenance must be performed with
the engine running, always work as a two
person team with one person sitting in the
operator’s seat while the other works on
the machine.
• When performing maintenance, be sure
to keep your body and clothing away
from moving parts.
Always clean the machine Stay clear of moving parts
¡ Clean the machine before performing ¡ Stay clear of all rotating and moving parts.
maintenance. Wrapping or entanglement may result in
¡ Stop the engine and cover electrical parts serious injury or death.
when washing the machine. Water on ¡ Keep hands, clothing and tools away from
electrical parts could cause short-circuits the rotating fan and running fan belts.
or malfunctions.
Do not use water or steam to wash the
battery, sensors, connectors or the
operator’s compartment.
26
SAFETY
Securely block the machine or Cautions on working on the

any component that may fall machine
L3A005
¡ Before performing maintenance or repairs ¡ When performing maintenance on the

under the machine, set all working machine, clean up the foot area and strictly
equipment against the ground or in the observe the following so as not to fall:
lowermost position. • Do not spill oil or grease.
¡ Securely block the tracks. • Do not leave tools laying around.
¡ If you must work beneath the raised • When walking, watch your step.
machine or equipment, always use wood ¡ Never jump off the machine. Use the steps
blocks, jack-stands or other rigid and and handrails when climbing on and off
stable supports. Never get under the the machine, and always support your
machine or working equipment if they are body at three points with your hands and
not sufficiently supported. This procedure feet.
is especially important when working on ¡ Use protective equipment as required by
hydraulic cylinders. job conditions.
Securely block the working Place heavy objects in a stable

equipment position
To prevent unexpected movement, securely
block the working equipment when repairing
or replacing the cutting edges or bucket teeth.
Secure the engine hood or cover

when opened
When removing or installing the hoe
Be sure to secure the engine hood or cover attachment, place it in a stable position so
when opening it. Do not open the engine that it does not tip over.
hood or cover on slopes or in strong wind.
27
SAFETY
Use caution when fueling Be careful with hot and

pressurized components
¡ Do not smoke or permit open flames while

fueling or near fueling operations. Stop the engine and allow the machine to
¡ Never remove the fuel cap or refuel with cool down before performing inspection and
the engine running or hot. Never allow fuel maintenance.
to spill on hot machine components. ¡ The engine, muffler, radiator, hydraulic
¡ Maintain control of the fuel filler nozzle lines, sliding parts and many other parts
when filling the tank. of the machine are hot directly after the
¡ Do not fill the fuel tank to capacity. Allow engine is stopped. Touching these parts
room for expansion. will cause burns.
¡ Clean up spilled fuel immediately. ¡ The engine coolant, oil and hydraulic fluid
¡ Tighten the fuel tank cap securely. Should are also hot and under high pressure.
the fuel cap be lost, replace it only with Be careful when loosening caps and
the original manufacturer’s approved cap. plugs. Working on the machine under
Use of a non-approved cap without proper these conditions could result in burns or
venting may result in pressurization of the injuries due to the hot oil spurting out.
tank.
¡ Never use fuel for cleaning purposes.
¡ Use the correct fuel grade for the operating Be careful with hot cooling
season. systems
Handling of hoses
Fuel, oil or hydraulic fluid leaks can cause a
fire.
¡ Do not twist, bend or hit the hoses. Do not remove the radiator cap or drain plugs
¡ Never use twisted, bent or cracked hoses, when the coolant is hot. Stop the engine, let
tubes and pipes. They may burst. the engine and radiator cool and loosen the
¡ Retighten loose connections. radiator cap or drain plugs slowly.
28
SAFETY
Be careful with fluids under ¡ Stop the engine and turn the starter switch
to the ON position and move all the control
pressure
levers and pedals several times in all
Pressure can be maintained in the hydraulic directions to release the pressure from the
circuit long after the engine has been shut working equipment circuitry.
down. (When equipped with accumulator)
¡ Release all pressure before working on ¡ When removing plugs or screws or
the hydraulic system. disconnecting hoses, stand to the side and
loosen slowly to gradually release the
internal pressure before removing.
¡ Hydraulic fluid under pressure can

penetrate the skin or eyes and cause Handling of the Accumulator
injury, blindness or death. Fluid escaping
from a small hole can be almost invisible.
Wear a safety goggles and heavy gloves
and use a piece of cardboard or wood to
search for suspected leaks.
If fluid is injected into the skin, it must be
removed within a few hours by a doctor
familiar with this type of injury.
N0A0051
High pressure nitrogen gas is enclosed in

the accumulator and incorrect handling could
possibly bring about serious personal injury
due to explosion. The following matters
should be strictly observed:
¡ Do not disassemble.
Release all pressure before ¡ Do not bring close to fire or throw into a
working on the hydraulic system fire.
¡ Do not make hole, weld, or fuse.
Oil may spurt out if caps or filters are removed ¡ Do not subject to shock such as hitting or
or pipes disconnected before releasing the rolling.
pressure in the hydraulic system. ¡ At time of disposal, it will be necessary to
¡ Gradually press the air breather button to release the enclosed gas. Please contact
relieve tank pressure. a Takeuchi sales or service outlet.
29
SAFETY
¡ Wear safety glasses and gloves when

Disconnect the battery
working with batteries.
¡ Batteries generate flammable and
explosive gases. Keep arcs, sparks,
flames and lighted tobacco away.
¡ Use a flashlight to check battery electrolyte
level.
¡ Stop the engine and shut off electrical
equipment while inspecting or handling the
battery.
¡ Do not short circuit the battery posts with
Disconnect the battery before working on the metal items.
electrical system or doing any welding. ¡ Always unfasten the negative (–) battery
Remove the negative (–) battery cable first. cable first when disconnecting the battery
When reconnecting the battery, connect the cable. Always connect the negative (–)
negative (–) battery cable last. battery cable last when fastening the
battery cable.
¡ Loose battery terminals may result in
sparks. Be sure to fasten terminals tightly.
¡ Make sure the vent caps are tightened
securely.
¡ Do not charge a battery or jump-start the
engine if the battery is frozen. Warm to
15°C (60°F) or the battery may explode.
¡ Do not use the battery when the fluid level
Avoid battery hazards is below the lower level. Doing so will
hasten the deterioration of the internal
¡ Batteries contain sulfuric acid which will portions of the battery and shorten the
damage eyes or skin on contact. battery life, and can also cause rupturing
• If acid contacts eyes, flush immediately (or an explosion).
with clean water and get prompt medical ¡ Do not fill the battery above the upper
attention. level. Doing so could cause the fluid to
• If acid is accidentally swallowed, drink leak, contact and damage the skin, or
large quantities of water or milk and call cause parts to corrode.
a physician immediately.
• If acid contacts skin or clothing, wash
off immediately with clean water.
30
SAFETY
Have a Takeuchi service agent Disposing of wastes

repair welding cracks or other
damage
Ask a Takeuchi service agent to repair any
welding problems which are detected. If not
feasible, make sure the welding is done by a
qualified person in a properly equipped
workplace.
¡ Funnel spent fluids from the machine into

Vibrations to which the operator containers. Disposing of fluids improperly
is subjected destroys the environment.
¡ Follow the prescribed regulations when
According to the results of the tests carried disposing of oil, fuel, engine coolant,
out to determine the vibrations transmitted refrigerant, solvents, filters, batteries or
to the operator by the machine, the upper other harmful substances.
limbs are subjected to vibrations lower than
2.5 m (8.2 ft) / sq.sec. while the seated part
of the body is subjected to vibrations lower
than 0.5 m (1.64ft) / sq.sec.
Checks after maintenance

¡ Gradually raise the engine speed from a
low idle to maximum speed and check that
no oil or water is leaking from serviced
parts.
¡ Move the controls and check that the
machine is operating properly.
31
SAFETY
Safety Signs (Decals)
The following safety signs (decals) have been placed on your machine in the areas indicated.
They are intended for the personal safety of you, and those working with you. Please take
this manual, walk around your machine and note the content and location of these safety
signs. Review these signs and the operating instructions in this manual with your machine
operators.
¡ Keep the signs legible. If they are not, obtain replacements from your Service outlet.
7 10 11 2 1
2
1
2 9
12
12 5 3
4 8 6
13
12
L3A0033
32
SAFETY
1. No.03593-06500 5. No.03593-47020
WARNING WARNING
DO NOT WHEN BUCKETS WIDER THAN STANDARD
enter into ARE FITTED TO THIS MACHINE,
CAB(CANOPY)DAMAGE MAY OCCUR WHEN
swinging area FULL LEFT HAND BOOM OFFSET IS USED.
03593-47020
2. No.03593-07400 6. No.03393-75040
CAUTION CAUTION
DO NOT USE ETHER
STOP ENGINE USAGE OF ETHER FOR STARTING
PURPOSES MAY CAUSE INTERNAL
BEFORE OPENING ENGINE DAMAGE. 03393-75040
03593-07400
7. No.05693-21980
3. No.03593-13700
WARNING WARNING
1 - This machine,if improperly operated or
maintained can cause bodily harm,or even Engine may be HOT
DEATH.
05693-21980
2 - Read and understand the owners manual
supplied with this machine before operating.
3 - Keep all safety devices in place and
8. No.05693-53810
functional.
4 - Do not operate the machine unless the seat
belt is properly fastened around you.
CAUTION
5 - Follow the instructions in the Operator’s Setting this switch to the “OFF”
Manual when hoisting the machine or position will shut down all of
fastening it to the transport vehicle. 03593-13700 the electrical circuits and the
memory of the radio preset
tuning buttons will be deleted.
05693-53810
4. No.03593-47010
9. No.03993-00400
WARNING Position of Fire extinguisher
THIS EXCAVATOR
MUST NOT BE USED
AS A CRANE 03593-47010
Except for UK
33
SAFETY
10. No.03593-06600 13. No.05693-52528

Diesel Fuel for EU
Noise Outside the Cab
This value indicates the noise level
outside the machine and refers to the
noise perceived by the persons who
D are in the vicinity of the work area.
Diesel Fuel Only
03593-06600
11. No.03593-06700
Hydraulic oil
Serial No. 17514412 ~

No.05693-49035
12. No.03993-00500
Position of Hoisting
34
CONTROLS
Names of Components .............................. 36
Doors and Covers ...................................... 38
Seat and Seat Belt ...................................... 43
Instrument cluster ...................................... 46
Switches ..................................................... 48
Levers and Pedals ..................................... 53
Accessories ............................................... 55
35
CONTROLS
Names of Components
Mono-Boom
4 3 5 2 1 16 15 14
13
19
12
6 11
10
9
8
7 18 21 17 20
L3B001
Upperstructure Undercarriage Working equipment

1. Cab 6. Crawler belt 11. Bucket
2. Seat 7. Idler 12. Bucket cylinder
3. Engine hood 8. Track roller 13. Arm
4. Fuel tank 9. Carrier roller 14. Arm cylinder
5. Hydraulic tank 10. Travel motor 15. Boom
16. Boom cylinder
2-Piece Boom 17. Boom bracket
18. Swing cylinder
15 22 19. Auxiliary hydraulic lines
20. Dozer blade
21. Blade cylinder
22. Intermediate boom
23. Boom adjustment cylinder
23
16
L3L0151
36
CONTROLS
Names of Components
15 10 7 14 5 14 23 13 22 4 17 11
1
16
9
12
24
6
21
3
18
2
20 8
19
L3B0022
1. Instrument cluster 13. Boom swing pedal

2. Starter switch 14. Travel lever
3. Light switch 15. Auxiliary hydraulic switches
4. Horn button 16. Blade lever
5. Travel speed switch 17. Decel. button
6. Wiper switch 18. Fan switch (Heater)
7. Safety lock lever 19. Heater / Defroster switch
8. Slew speed switch 20. Ventilation/Circulation switch
9. Power mode buttons 21. Cigarette lighter
Throttle buttons 22. Selector Button (2-Piece boom)
10. Left operating lever 23. Pedal lock
11. Right operating lever 24. Intermediate boom operation indicator
12. Fuse box lamp (2-Piece boom)
37
CONTROLS
Doors and Covers
Opening
Starter Key
1. Pull the knob (1) towards you and open
the door.
To open the door from inside the cab, push
the lever (2) to the front.
2. Open the door fully and press it against
the cab to lock it in place.
Closing
E4B003
4
The starter key is used not only to start and
stop the engine, but also to lock and unlock
the following places: 3
¡ Fuel filler cap
¡ Cab door
¡ Covers C4C002
1. Either push release lever (3) to the front

or lower release lever (4).
Cab Door
2. Close the released door.
WARNING
When mounting and dismounting the
cab, first open the door fully to the locked
position and check that it does not move.
Open the door fully and press it against the

catch at the back of the door to lock it in place.
Always lock the door when mounting and
dismounting and when operating the
machine. Front Window
Lock and unlock WARNING
2 1 ¡ Grasp the handles firmly with both
hands when opening and closing the
front window. Your head or hands may
get caught if they slip.
¡ If you open the front window, be sure
to lock it in place with the lock pins on
the left and right sides. The window
C4C001
may fall if it is not locked in place.
1. Insert the starter key and turn it.
38
CONTROLS
Doors and Covers
Opening 1. Pull the left and right lock pins (1) to the
inside and turn them to the locked position
to unlock the front window. If the lock pins
(1) are partially sticking out they may
cause damage.
1 3 1 2. Grasp the front (lower) handle (2) with the
Released Locked left hand, the rear (upper) handle (3) with
the right hand, then slowly lower the front
1 1 window.
C4C003
3. Move the lock pins (1) to the outside to
1. Park on a level surface and stop the lock the front window.
engine.
2. Set the safety lock lever to the locked
position.
3. Pull the left and right lock pins (1) to the Lower Front Window
inside then turn them to the locked position
Removing
to unlock the front window. If the lock pins
(1) are partially sticking out they may
4 4
cause damage.
2
C4C005
1. Open the front window and stow it in the

ceiling.
1 3 1
C4C004 2. Grasp the protruding parts (4) on the left
and right with your fingers and slowly lift
4. Grasp the lower handle (2) with the left
the lower front window off.
hand, the upper handle (3) with the right
hand, then lift and slide to the rear.
5. Once the window frame is against the
stopper, move the lock pins (1) to the 4 4
outside to lock front window.
Closing
5 5
WARNING
6 6 C4C006
When closing the front window, lower the
window slowly so as not to hit your head. 3. Hold the glass firmly, place the lower front
Lowering the window abruptly may result window through the guides (5) at the rear,
in injury or damage the front window. then set it on the supports (6) and fasten
it in place.
39
CONTROLS
Doors and Covers
Opening
Side Window
1. Insert the starter key and turn it
counterclockwise to unlock the front cover
(1).
7
2. Tilt the front cover (1) until it stops.
Closing
1. Support the front cover (1) by hand and
release the stay (2).
2. Close the front cover (1).
C4C007
3. Insert the starter key and turn it clockwise
1. Grasp the catch (7), unlock it and open to lock the front cover (1).
the side window.
2. To close the side window, close it until a
click is heard.
Front Cover (Tool Box) Side Covers
CAUTION CAUTION
¡ Never jump off the machine. Use the ¡ When opening the side cover, open it
steps and handrails when climbing on firmly to the locked position.
and off the machine, and always ¡ When opening and closing the side
support your body at three points with cover, be careful not to get your hands
your hands and feet. or other parts of your body caught.
¡ When opening the front cover, open it
firmly to the stopped position.
¡ When opening and closing the front 1
cover, be careful not to get your hands
or other parts of your body caught.
The grease gun and tools are stored under 2

the cover.
3 L3B054
1
Opening
1. Insert the starter key and turn it
2 counterclockwise to unlock the side cover.
2. Lift the side cover fully until it stops.
3. Press the stay (2) to fix the side cover.
Engine hood unlock knob (3) is located
L3B007
behind the right side cover.
40
CONTROLS
Doors and Covers
Closing
Maintenance Cover
1. Support the side cover (1) by hand and
release the stay (2).
2. Close the side cover (1) and press it down WARNING
until a click is heard at the front. ¡ Before opening the maintenance cover,
stop the engine.
¡ When maintenance on the machine,
clean up the foot area and strictly
observe the following so as not to fall:
Engine Hood • Do not spill oil or grease.
• Do not leave tools laying around.
WARNING • When walking, watch your step.
¡ Never jump off the machine. Use the
Before opening the engine hood, be sure steps and handrails when climbing on
to stop the engine. If your hands or tools and off the machine, and always
should get caught in the fan or fan belt support your body at three points with
while the engine is running they may be your hands and feet.
severed. ¡ Use protective equipment as required
by job conditions.
1
2
L3B009 3
L3B053
Opening
1. Open the right side cover and pull the Opening
unlock knob (3). 1. Insert the starter key and turn it
Refer to “Side Covers”. counterclockwise to unlock the
2. Lift the engine hood (1) fully. maintenance cover (1).
2. Pull the knob (2), then lift the maintenace
Closing cover (1) fully until it stops.
1. Close the engine hood and press it down
until a click is heard at the front. Closing
1. Support the maintenance cover (1) by
hand and release the stay (3).
2. Close the maintenance cover (1).
3. Insert the starter key and turn it clockwise
to lock the maintenance cover (1).
41
CONTROLS
Doors and Covers
Fuel Filler Cap
WARNING
steps and handrails when climbing on
and off the machine, and always
support your body at three points with
your hands and feet.
¡ Do not smoke or permit open flames
while fueling or near fueling
operations.
¡ Supply fuel in a well ventilated place
and with the engine stopped.
¡ Clean up spilled fuel immediately.
¡ Do not fill the fuel tank to capacity.
Allow room for expansion.
¡ Tighten the fuel filler cap securely.
Close Open
L3B011E
Opening
1. Open the key cover, insert the key and
turn it clockwise to unlock the fuel cap.
2. Turn the fuel cap counterclockwise and
remove it.
Closing
1. Set the fuel cap in place and turn it
clockwise.
2. Turn the key counterclockwise to lock the
fuel cap, then remove the key.
42
CONTROLS
Seat and Seat Belt
¡ Lower lever (2) to adjust the front angle of

Seat
the seat cushion.
1. To raise the front angle of the seat cushion,
WARNING apply your weight to the backrest while
Adjust, secure and latch the operator’s holding the lever down.
seat. 2. To lower the front angle of the seat
cushion, apply your weight to the front of
the seat cushion while holding the lever
down.
G 7 ¡ To adjust the height of the seat, adjust the
front and rear angles of the seat cushion
alternately.
C (5 steps, 60 mm (2.36 in.) adjustment
A range)
Example: First raise the front angle of the
1 seat cushion, then raise the rear
2 angle of the seat cushion by the
same amount. This raises the
3 B height of the seat.
4 D ¡ After adjusting to the desired position,
release the lever to lock it.
5 E F
6 (C) Back angle adjustment
L3B012
(A) Lumber adjustment

WARNING
1. Turning knob (1) in the direction of the ¡ Do not set the seat back to its
arrow causes the lumber of the backrest maximum reclining position and slide
to curve outwards for greater back support. the seat backwards at the same time.
2. Turning the knob (1) further then removes Doing so may break the rear window
the curve and returns the seat to its original glass, resulting in injury.
position. ¡ Be careful not to allow the force of the
The knob (1) cannot be turned counter to spring to bring the seat back sharply
the direction of the arrow. forward.
(B) Seat cushion angle and height 1. Raising your torso, sitting down firmly in
adjustment the seat.
¡ Lift lever (2) to adjust the rear angle of the 2. Pulling lever (3) allows you to use the
seat cushion. pressure of the springs in the seat pressing
1. To raise the rear angle of the seat cushion, against your back to adjust the reclining
raise yourself slightly off the seat while angle of the seat back. Release the lever
lifting the lever. (3) at the desired angle and the seat back
2. To lower the rear angle of the seat cushion, will remain fixed in that position.
apply your weight to the rear of the seat
cushion while lifting the lever.
43
CONTROLS
Seat and Seat Belt
(D) Fore-and-aft adjustment

1. Pull on lever (4) and slide the seat
backward or forward to bring it to the
optimum position for operating the
machine.
2. Release the lever (4) at the desired
position and the seat will remain fixed
there.
Adjustment stroke: 17 steps,160 mm (5.9 in.)
3 2
4
E
5
6
L3B013
(E) Weight adjustment

1. Turn handle (5) and set it to indicate the
weight of the person to operate the
machine.
May be set to any value from 50 to 120 kg
(110 to 265 lbs.)
(F) Lever stand adjustment

1. Pull on lever (6) and slide the lever stand
backward or forward to bring it to the
optimum position for operating the
machine.
2. Release the lever at the desired position
and the lever stand will remain fixed there.
Adjustment stroke: 70mm (2.8 in.)
(G) Headrest adjustment

The position of the headrest (7) can be
adjusted in the up and down directions.
1. Grasp the headrest with both hands and
move it upwards or downwards.
44
CONTROLS
Seat and Seat Belt
Seat Belt
CAUTION
Always fasten the seat belt securely
before starting the engine.
Fastening the seat belt

1. Adjust the seat to the optimum position
for operating, raise your torso, and sit back
firmly into the seat.
2. Pull the seat belt to the desired length.
B E4B023
3. Make sure that the belt is not twisted and

then insert the tongue plate (A) into the
buckle (B) of the seat belt until you hear a
clicking sound as it locks in place.
Releasing the seat belt
E4B024
1. To remove the seat belt, simply press the

button (C) located on the buckle.
The seat belt is automatically stowed
away.
45
CONTROLS
Instrument Cluster
1
11 L FC H
4
2
13
3
5
14
6
7
12
9
10
8 L3B014
4. Battery Charge Warning Lamp

Warning Lamps
This lamp flashes and an
IMPORTANT: If a warning lamp flashes alarm is sounded if a
and an alarm is sounded, stop all problem arises in the
C4B030
operations immediately and inspect and charging system while the
maintain the appropriate part. engine is running.
Refer to page 148 “Troubleshooting”.
5. Air Cleaner Warning Lamp
1. Engine Emergency Lamp This lamp flashes and an
This lamp flashes and an alarm is sounded if the air
alarm is sounded if the cleaner filter is clogged while
engine oil pressure or the G4B010
the engine is running.
G4B009
coolant level in the radiator
drops or the coolant temperature rises 6. Water Separator Warning Lamp
abnormally while the engine is running. After This lamp flashes and an
approximately 5 seconds, the engine stops alarm is sounded if the water
or low idling automatically.
is detected within the water
L3B015
separator while the starter
2. Engine Oil Pressure / Coolant Level
switch is in the ON position.
Warning Lamp
alarm is sounded if the 7. Fuel Level Warning Lamp
lubricant oil pressure or This lamp lights when the
L3B036
coolant level in the radiator fuel level is low while the
drops abnormally while the engine is running. starter switch is in the ON
L3B016
position.
3. Coolant Temperature Warning Lamp
alarm is sounded if the
engine coolant temperature
C4B012
rises abnormally while the
engine is running.
46
CONTROLS
Instrument Cluster
Indicators Meters
8. Glow Lamp 12. Hour Meter
This lamp turns off when This displays the total engine
engine preheating is running time in hours.
completed. The rightmost digit indicates
C4B013 L3B019
tenths of hours (6 minutes).
Set the inspection and maintenance intervals
9. Travel Speed Lamp according to the time displayed on the hour
This lamp lights when the meter.
travel speed switch is set to
2nd (high speed). 13. Water Temperature Gauge
C4B014
This gauge indicates the
temperature of the engine
10. Slow Speed Slew Lamp coolant water.
This lamp lights when slow L3B020
The needle should be within
speed slew switch pressed, the green range during machine operation.
the slew speed decreases. The red range indicates overheating.
L3B017
14. Fuel Gauge

11. Power Mode Lamp This gauge indicates the
These lamps indicates the amount of fuel in the tank.
engine speed. Be sure to top off the tank
L3B021
L FC H before running out of fuel.
L3B018
47
CONTROLS
Switches
Starter Switch Battery Switch
OFF IMPORTANT: Never set this switch to the

ON OFF (O) position while the engine is
START
running.
Doing so might cause damage to the
electrical system.
L3B043
IMPORTANT: Do not repeatedly switch

the key from OFF to ON and ON to OFF
over a short period. Doing so will cause
engine breakdown.
L3C004
OFF ........ Position for stopping the engine

and inserting or removing the key. OFF (O) .. Switches off the electrical circuit.
ON .......... Position in which the engine is Be sure to set this switch to the
running. At this position, all the OFF (O) position when storing the
electrical equipment is functional. machine for a long period, or
When the coolant temperature is when performing maintenance of
low, the air heater is energized the electrical system.
and automatic preheating is ON ( I ) .... Connects the electrical system.
done. Check that this switch is in the
START .... Position for starting the engine. ON ( I ) position before starting
When the key is released, the the engine.
switch automatically returns to the
ON position. Supplement: Setting this switch to the
OFF (O) position will shut down all of the
electrical circuits and the memory of the radio
preset tuning buttons will be deleted.
48
CONTROLS
Switches
Horn Button Selector Button (2-Piece boom)
WARNING
Pressing (switching ON or OFF) the
selector button while the boom swing
pedal is depressed is dangerous, since
the attachment will move unexpectedly.
Always set the boom swing pedal back
L3B046
to the neutral position before operating
the selector button.
Press the button on the right operating lever
to blow the horn.
Decel. Button
WARNING
Set the operating and travel levers to L3L020
neutral before operating the decel. button.
The machine’s operating speed will This button changes from the boom swing
change abruptly if the button is operated operation to the intermediate boom
while the levers are engaged. operation.
Press this button to change over to operation
of the intermediate boom . The intermediate
boom operation indicator lamp will light. One
L FC H more press of this button will result in a return
to boom swing operation. Actual operation
is performed with the boom swing pedal.
L3B0471
Press the button on the right operating lever

to lower the engine speed to low idling.
Press the button again to return to the engine
speed set with the throttle or power mode
buttons.
Note: The one-touch decelerator is a device
for lowering the engine speed and reducing
fuel consumption when little engine output
is required, for example when the operating
and travel levers are in neutral.
49
CONTROLS
Switches
Intermediate Boom Operation First Auxiliary Hydraulic Switches

Indicator Lamp (2-Piece boom)
Slider Switch
(Proportional control)
Proportional control allows for slow-to-fast
movement of auxiliary functions.
Example: If you move the slider switch half
way, the auxiliary function will move at
approximately one-half speed.
L3L017
A
This lamp illuminates when the intermediate B
boom operation is chosen by the selector
button.
Travel Speed Switch L3L021
Move this switch to control the flow of the oil

WARNING in the first auxiliary hydraulic lines.
When a load greater than a set value is
applied during 2nd speed (high speed) Auxiliary Hydraulic Buttons
A
becomes lighter, the speed will increase B
L3L035
Press those buttons to control the flow of the

oil in the first auxiliary hydraulic lines.
¡ Proportional control of the auxiliary
hydraulic circuit is not possible.
(A) .... Hydraulic oil flows to left auxiliary

line(a)
(B) .... Hydraulic oil flows to right auxiliary
Press this switch to set the travel speed to line(b)
2nd speed (high speed). Press again to
return to 1st speed (low speed).
50
CONTROLS
Switches
Power Mode Buttons Throttle Buttons
L3B025 L3B026
The engine speed can be changed at the The engine speed increases and decreases
touch of a button. When one of these buttons continuously while these buttons are
is pressed, the engine is set to the set speed pressed. When the button is released, the
and the power mode indicator lights. engine speed is set to the speed at the time
the button is released.
: Engine speed increases
: Engine speed decreases
When the throttle buttons are operated and
L FC H the engine speed is at a point between the
different modes, the lamps on both sides
light. When the speed is changing, only the
lamp for the nearest engine speed lights.
L3D005
L: This mode is always set when the

engine is started.
Use it for light and very light operations.
FC: Use this mode for light operations and
leveling operations which do not require
speed. Using this mode reduces fuel
consumption and noise.
H: Use this mode for general digging and
loading operations requiring power and
speed.
51
CONTROLS
Switches
Slew Speed Switch Light Switch
L3B027 L3B028
Pressing this switch shifts rotation into Slow When this switch is turned while the starter
speed, bringing its speed down to the switch is at ON, the lights turn on as follows:
minimum. Slow speed is useful for O ...... Off
performing tasks that require precision I ....... Meter light, front light, side lights, tail
handling even at the cost of speed or lights and boom light turn on.
efficiency.
Slow speed
Wiper Switch
The lamps on the switch and instrument
panel will light up. Used for low speed slew. IMPORTANT: If no washer fluid is
The maximum set speed in slow speed can discharged, do not operate the washer.
be adjustable. Doing so may damage the pump.
Upon shipment, it is set to 7.6 min –1 (7.6 rpm). IMPORTANT: Operating the wiper with no
Contact a Takeuchi sales or service outlet moisture on the windshield will scratch
for change. the glass. Apply water or washer fluid
when operating the wiper.
Normal speed IMPORTANT: In cold seasons, the wiper
The lamps will go out and slew will return to blade may freeze to the glass. Operating
its normal speed. the wiper forcibly may damage the wiper
Supplement: As a safety precaution, the motor.
machine is designed so that you cannot
switch to normal speed while slewing in slow
speed. You must instead bring the rotation
to a temporary halt and then press the slew
speed switch to return to normal speed.
PUSH
L3B0291
O ............ Off
I ............. Wiper INT
II ............ Wiper
PUSH ..... Washer
52
CONTROLS
Levers and Pedals
Safety Lock Lever Boom Lock Valve (2-Piece boom)
WARNING
¡ Before leaving the operator’s seat,
raise the safety lock lever to engage
the lock and stop the engine.
If any controls should be touched
accidentally when the safety lock lever
is lowered, the machine will move L3L023
suddenly, and cause serious injury or
death. Serial No. 17510003 ~ 17512503
¡ Note that the dozer blade control is not This valve blocks the hydraulic oil flow to
locked, even when the safety lock lever prevent the boom from lowering.
is set to the lock position. Do not touch Lower the lever to engage the boom lock.
this control accidentally. Raise the lever to disengage the boom lock.
¡ Be careful not to touch the operating
levers when raising and lowering the
safety lock lever. Operating Levers
WARNING
¡ Be careful to check which pattern of
lever control arrangement you are
operating with before beginning
operations.
¡ The explanations in this manual are for
L3B030 the ISO pattern.
This device is for locking the hoe attachment,

auxiliary hydraulic control, slewing and
traveling.
When the lever is raised, the lever stand
springs up and the lever is locked.
L3B048
Use these levers to operate the boom, arm,

bucket and upperstructure (slew).
Refer to page 68 “Lever Pattern”.
Refer to page 75 “Operating the Working
Equipment”.
53
CONTROLS
Levers and Pedals
Blade Lever Boom Swing Pedal
B
A
B
L3B049 L3B052
Use this lever to operate the dozer blade. Use this pedal to operate the boom swing.
(A) .... Blade up Operation switches to the intermediate boom
(B) .... Blade down when the selector button is pressed.
Refer to page 76 “Operating the Dozer (A) .... Boom swing left/Intermediate boom
Blade”. raise
(B) .... Boom swing right/Intermediate boom
lower
Refer to page 76 “Operating the Boom
Travel Levers
Swing” or “Operating the Intermediate
Boom”.
WARNING
Before operating the travel levers, check Pedal Lock
to make sure that the dozer blade is to
the front of the operator’s seat. BE
WARNING
AWARE that when the dozer blade is to When not using the pedal, set the pedal
the rear of the operator’s seat, the travel lock to the locked position. Stepping on
levers operate in the opposite direction a pedal accidentally when it is not locked
to when the dozer blade is in the front. may lead to unexpected accidents.
L3B050
L3B051
Use these levers to move forward and This device is for locking the swing pedal.
backward and to change directions. Set the pedal lock over the pedal to lock it.
Refer to page 72 “Operating the Travel
Levers”.
54
CONTROLS
Accessories
Outlets
Heater
WARNING 1
¡ Always be sure to allow sufficient
ventilation.
¡ Do not place combustible or explosive
objects near the air outlets.
L3B039
Fan Switch
Move knob (1) up and down or left and right
to adjust the direction of the air.
OFF
Supplement: Use the heater with care in
warm seasons. Coolant circulates in the
heater even when the heater switch is turned
off.
When the heater is no longer needed, stop
L3B037 coolant circulation as follows:
OFF .. Off
o ...... Heater fan rotates at low speed. IMPORTANT: Use the valve (1) either fully
O ...... Heater fan rotates at high speed. open or fully closed.
Cooling water could leak when the valve
Heater / Defroster / Ventilation / is set at a halfway position.
Circulation Switch
L3C003
L3B038 1. Park on a flat surface and stop the engine.

Use this switch to heat the cab and to defrost 2. Open the maintenance cover.
the windshield. 3. Turn the valve (1) clockwise until it stops
..... Heater to close it.
..... Windshield defroster
.... Full ventilation
.... Half ventilation
...... Internal circulation
55
CONTROLS
Accessories
b. With the engine running at low idle

First Auxiliary Hydraulic Lines
operate the auxiliary hydraulic switches
repeatedly (approx. 10 times) to purge
WARNING air from the hydraulic lines.
c. Stop the engine and wait for more than
Oil may spurt out if caps or filters are removed 5 minutes until bubbles escape from the
or pipes disconnected before releasing the hydraulic oil in the tank.
pressure in the hydraulic system.
¡ When disconnecting hoses, release the IMPORTANT: Follow the procedures for
internal pressure before removing. purging air as instructed by the attachment
manufacturer if specified to do so.
These lines deliver the hydraulic oil
necessary for operating a hydraulic breaker, 6. Check for leaks.
crusher or other attachments.
Disconnecting the hydraulic circuits
S O 1. Release the pressure remaining in the
lines then close the stop valve.
Refer to “Releasing the residual pressure”.
2. Disconnect the lines from ports (a) and (b).
3. Install the plugs.
b
a Releasing the residual pressure
L3C0012 After using the auxilliary hydraulic circuits,
pressure remains in the circuits. This is called
Stop valve ..... S : Closed O : Open
the residual pressure. Release this residual
pressure before disconnecting the lines.
Connecting the Hydraulic Circuits
To connect the attachment hydraulic lines,
use the following procedures: A
1. Release the pressure remaining in the
lines then close the stop valve. B
2. Remove the plugs.
3. Connect the attachment hydraulic lines to
ports (a) and (b). L3L035
When fitted with a hydraulic breaker, 1. Start the engine and press the auxiliary
connect the return circuit to port (b) and hydraulic button (B).
the supply circuit to port (a). (The residual pressure is released from
4. Open the stop valves. the (a) port line, and pressure is generated
When fitted with a hydraulic breaker, open in the (b) port line.)
the selector valve (1). 2. Stop the engine and open the selector
Refer to page 57 “Selector Valve”. valve (1) on the machine body.
5. When connecting is complete, purge air (The residual pressure is released from
from the hydraulic lines. the (b) port line.)
a. Start and run the engine at low idle with When equipped with accumulator (option):
no load for 10 minutes. Refer to page 199 “Accumulator”.
56
CONTROLS
Accessories
Selector valve Use these sockets as an external power

supply. When using this socket, be careful
not to exceed 24V/5A.
To use, raise the cap (1).

Open ............ When using a hydraulic

breaker (1-way flow)
Closed .......... When using a reversible
attachment (2-way flow)
Change the direction of the hydraulic oil flow
by opening or closing the selector valve on
the machine body.
External Power Sockets (for EU) Interior Light

IMPORTANT: The battery capacity will
WARNING
decrease if the interior light is left on for
Only use applicable electric products with long periods of time the engine stopped.
these sockets. Turn the lamp off when leaving the
machine.
N0B031
for Beacon OFF ........ Lamp is turned off all the time,
with no regard for the door being
opened or closed.
Neutral .... Lamp is turned on when the door
1 is opened, and it turned off when
the door is closed.
ON .......... Lamp is turned on all the time,
with no regard for the door being
opened or closed.
N0C008
57
CONTROLS
Accessories
Cigarette Lighter Ashtray
WARNING WARNING
¡ Do not leave the cigarette lighter’s ¡ Be sure to extinguish cigarettes and
knob pressed in. Doing so heats up the matches completely before putting
lighter, and could be dangerous. them in the ashtray, and always close
¡ If the knob does not pop out after 30 the ashtray afterwards.
seconds, it may be broken. Pull it out ¡ Do not overfill the ashtray with
by hand. cigarette butts or put in paper or other
¡ Do not use other cigarette lighters, as easily burnable objects. Doing so could
they may get stuck. lead to fire.
¡ Only use applicable electric products
with this socket.
¡ Do not touch metal parts of the lighter. 1
Doing so could cause burns.
This is the cigarette lighter and internal power

supply socket.
When using this socket, be careful not to
exceed 24V/5A. L3B042
Pull the ashtray out towards you to use it.

To clean, press the ash discharge button (1)
and pull out the ashtray.
L3B041
1. Press the lighter in.

2. Release the lighter and wait for it to pop
out. The lighter pops out automatically
when the heater becomes red.
3. Once the lighter pops out, pull it out.
58
CONTROLS
Accessories
Radio
Operating precautions
¡ To ensure safe operation of the machine, always be sure to keep the volume of the radio
down to a level where you can easily hear sounds from outside the machine.
¡ Do not keep the radio playing for long periods of time with the engine stopped. Doing so
will drain the battery of its charge and make it difficult or impossible to restart the engine.
¡ Be careful not to allow water or other liquids to come into contact with the radio. Doing so
may result in it being rendered inoperable.
¡ Be careful not to insert cassette tapes backward. Doing so may damage the cassette
player. Insert tapes with the head of the tape facing to the right.
¡ Always remove the cassette from the player when not in use.
Names of components
16 3 15 6 7 8
BASS TRE
KRH–M867
DC12V/24V
AUTO REVERSE CASSETTE STEREO RECEIVER
PS/AS LOUD DISP

VOL
MTL LOUD ST 1 2 3
M
FM1
FM2
SEEK SEEK H AM
BAND DN UP 4 5 6
METAL
1 2 12 11 10 9 5 4 13 14
L2C001
(1) (2) Power switch / volume control knob (3) Tone control
Turn this knob clockwise. The “click” sound ¡ Bass control knob
indicates that the power supply is turned on. ¡ Treble control knob
Further turning increases the speaker
volume. If a tape is loaded in the radio, eject
the tape to switch to the radio.
59
CONTROLS
Accessories
(4) Program indicators (8) Fast-forward / rewind / program

Indicates tape direction. When s lamp is on. changeover button
Upper side of a tape is playback, t indicates
playback of lower side. Fast-forward
(5) Display
MTL LOUD ST
G D F E G FM1
FM2
AM
MTL LOUD ST
A FM1
FM2
C
AM
L2C003
B Fast-rewind / Stop
L2C002
(A) Band
(B) Time/Frequency MTL LOUD ST
(C) Memory channel(1–6) FM1
FM2
(D) Metal AM
(E) FM Stereo
(F) Loudness
(G) Tape direction
L2C004
(6) Eject button To fast-forward the tape, push the button

Push this button to eject the cassette tape. matching the direction of program indication
¡ To change over to radio while listening to and to rewind, push the other button. To stop
a cassette tape, press the EJECT button fast-forwarding or rewinding, lightly press the
to stop the tape and the system will button which is not locked to cancel the
automatically change over to radio. operation. The system will then start playing
the tape again normally.
(7) Cassette door
Insert the cassette tape with the exposed
magnetic tape side facing to the right.
¡ Simply insert a tape to change over to the
cassette tape mode while listening to the
radio.
60
CONTROLS
Accessories
(12) Band select switch

KRH–M867 Pressing the “BAND” button changes over
DC12V/24V
AUTO REVERSE CASSETTE STEREO RECEIVER between FM1, FM2 and AM (MW) bands.
The display indicates the receiving band
MTL LOUD ST 1 2 3
M
FM1
name and frequency.
FM2
H
AM
4 5 6
METAL
(13) Metal switch
L2C005 Press the “MTL” (5) button before playing a
metal or CrO2 tape.
To change the program, press the fast- The “MTL” indication appears on the display.
forward and rewind buttons simultaneously.
The direction of tape feed will reverse. (14) Preset switch keys
One station each in the FM1, FM2 and
¡ When the tape ends in one direction, the AM(MW) bands, respectively, can be preset
system automatically reverses the tape for each of these preset keys.
and plays the other side. When listening to a preset station, select
¡ To stop fast-forwarding or rewinding, lightly either of the AM, FM1,FM2 bands using the
touch the unlocked key. This frees the band select switch, then simply press the
locked key and normal playing resumes. number key corresponding to the preset
selected station.
(9) Tuner switch (Manual tuning) The system can memorize 6 stations in AM
Pressing the shaped TUNER button raises band and 12 stations in FM bands (FM1: 6
the receiving frequency. Pressing the stations and FM2: 6 stations).
shaped TUNER button lowers the receiving
frequency similarly. Pressing either of these Manual Memory
buttons continuously shifts the receiving Use manual tuning button or seek tuning
frequency continuously. button to choose a radio station if a
broadcasting station is wanted to be
(10) SEEK switch recorded. For 2 seconds press 1–6 preset
Pressing the “SEEK” button shifts the key when the indication of frequency has
receiving frequency in the higher or lower already shown and the frequency is
frequency direction before automatically recorded. Flash stops and channel starts
stopping at a position where a station is functioning.
picked up.
¡ If the main power supply is interrupted,
(11) LOUD switch such as when exchanging machine
This button is used to operate the system at battery, all presettings will be erased.
a lower sound volume but with enhanced Repeat the presetting procedure in
bass and treble sound. (“LOUD” indication such case.
appears on the display.)
61
CONTROLS
Accessories
(15) DISP(Time/Frequency) button ¡ Set the time

This system is equipped with a clock which
TRE BASS TRE
can show the accurate time. Even if the radio
is off, the clock still shows the time.
(16) PS/AS switch AS LOUD DISP

VOL
M
PS/AS LOUD DISP
Push this button 2 sec below will

automatically operates to show the ND
SEEK
DN
SEEK
UP
H
BAND
SEEK
DN
SEEK
UP
H
memorized station from 1 to 6. The signal

L2C006
scaning start by pushing this button
momentarily. When a station is received the After pressing DISP button, press tuner
scaning automatically stops there for 5 button or to correct the time. Press tuner
seconds FLASHLY and then resumes button to set the “hour” and tuner button
scaning. As soon as the desired station is for setting the “minute”. Set the time when
found, press the this button again. the time is shown.
If you will auto memory push this button over

5 sec so initiates a scan of the band. Station
frequencies are either stored in order of low
of frequency for FM, or in sequence for AM,
starting from preset channel 1. If all of the
preset channels have not been filled up after
one scan, the remaining preset channels are
left unchanged, and channel 1 is recalled.
Channel 8 flashes during A.
62
OPERATION
Before Starting Operation ......................... 64
Starting and Stopping the Engine ............. 65
Machine Operation ..................................... 68
Operating Procedures ............................... 78
Parking the Machine .................................. 86
Handling in Cold Weather .......................... 87
Handling Rubber Crawlers ........................ 88
63
OPERATION
Before Starting Operation
Mounting and Dismounting Walk-Around Inspection

Perform the walk-around inspections before
WARNING
starting the engine the first time that day.
¡ Do not jump on or off the machine. Perform the inspections as described under
Never attempt to mount or dismount a “Maintenance - Walk-Around Inspection”
moving machine. (pages 105 and 106).
¡ When mounting and dismounting the
cab, first open the door fully to the
locked position and check that it does
not move.
Daily Inspection
Perform the daily inspections once a day
before starting the engine the first time that
day.
Perform the inspections as described under
N0D001
“Maintenance - Daily Inspection” (pages
107 to 111).
N0D002
¡ Always face the access system and

maintain a three point contact with the
recommended handrails and steps
while getting on and off the machine.
Keep steps and platform clean.
¡ Never use the safety lock lever or
control levers as hand holds.
64
OPERATION
Starting and Stopping the Engine
Before Starting the Engine

L FC H
1. Adjust the seat for a comfortable operating

position. 4
2. Fasten the seat belt.
2
L3D002
IMPORTANT: Do not start the engine

before the power mode lamp (L) lights.
¡ Check that the power mode lamp (L) is
lit.
¡ All the warning lamps flash and an
L3B030 alarm is sounded for 2 seconds. The
3. Check that the safety lock lever is in the meters also start functioning. After 2
locked position. seconds, only the battery charge
warning lamp (4) and engine oil
pressure / coolant level warning lamp
(2) flash, and the other lamps turn off.
¡ Turn the light switch to check that the
boom light, front light, side lights, tail
lights and meter light turn on.
¡ Check the fuel level.
If a lamp does not light or the alarm is not

sounded, the bulb may be burnt out or a wire
may be damaged. Contact a Takeuchi sales
C4D006
or service outlet for repairs.
4. Check that all the levers and pedals are
in the neutral position.
OFF
ON
START
L3D001
5. Insert the key into the starter switch, turn

it to the ON position, then perform the
following inspection:
65
OPERATION
Starting in Cold Weather

Starting the Engine
WARNING
¡ Clear the area of all persons.
¡ Sound horn to alert everyone around
the machine.
8
IMPORTANT: Do not run the starter motor L3D004
for more than 15 consecutive seconds. If
the engine fails to start, wait for 30 1. Make sure that the glow lamp (8) is lit.
seconds to protect the battery, and then (The glow lamp lights for 15 seconds when
try again to start the engine. coolant temperature is at –10°C (14F°).
Normal Starting
OFF
ON
OFF
ON START
START
L3D003
L3D003 2. After the glow lamp (8) turns off, then turn
1. Turn the key to the START position and the key to the START position and start
start the engine. the engine.
2. Once the engine starts, release the key. 3. Once the engine starts, release the key.
The key automatically returns to the ON The key automatically returns to the ON
position. position.
3. Check that the warning lamps are off. 4. Check that the warning lamps are off.
4. Warm up the engine. 5. Warm up the engine.
Refer to page 67 “Warming Up the Refer to page 67 “Warming Up the
Engine”. Engine”.
66
OPERATION
Warming Up the Engine Stopping the Engine

IMPORTANT: Avoid racing the engine IMPORTANT: Do not stop the engine
until it is warmed up. suddenly when operating with heavy
Do not warm up the engine for long loads or at maximum speed. Doing so
periods of time (20 minutes or more). may cause the engine to overheat or
seize. Never bring the engine to a sudden
stop except in the case of emergency.
L FC H L FC H
L3D005
L3B0471
1. Make sure that the power mode lamp (L)
ligts, then idle the engine and run it for 1. Press the decel. button.
about 5 minutes with no load. 2. Idle the engine for about 5 minutes to
gradually let it cool.
OFF
ON
START
L3D007
3. Turn the key to the OFF position to stop

the engine.
67
OPERATION
Machine Operation
Lever Pattern (ISO Pattern)
WARNING
¡ Be careful to check which pattern of lever control arrangement you are operating
with before beginning operations.
¡ The explanations in this manual are for the ISO pattern.
〈ISO〉〉
C4D006
Left Crawler Forward Right Crawler Forward
Left Crawler Reverse Right Crawler Reverse
Arm Out Boom Lower
Arm In Boom Raise
Upperstructure Slew Left Bucket Load
Upperstructure Slew Right Bucket Dump
Boom Swing Left Dozer Blade Lower

Intermediate Boom Raise
Boom Swing Right Dozer Blade Raise
Intermediate Boom Lower
68
OPERATION
Machine Operation
Lever Pattern (JCB Pattern)
WARNING
¡ Be careful to check which pattern of lever control arrangement you are operating
¡ The explanations in this manual are for the ISO pattern.
〈JCB〉〉
C4D013
Left Crawler Forward Right Crawler Forward
Left Crawler Reverse Right Crawler Reverse
Boom Lower Arm Out
Boom Raise Arm In
Upperstructure Slew Left Bucket Load
Upperstructure Slew Right Bucket Dump
Boom Swing Left Dozer Blade Lower

Intermediate Boom Raise
Boom Swing Right Dozer Blade Raise
Intermediate Boom Lower
69
OPERATION
Machine Operation
Warming Up the Machine

(Hydraulic Oil)
WARNING
Operating the working equipment without
warming up the machine (hydraulic oil)
is dangerous, as response will be slow L3D009
and the equipment may move in
2. Fully lower the safety lock lever to
unexpected ways and safety devices may
disengage the lock and lift the bucket from
not operate properly. Be sure to
the ground.
sufficiently warm up the machine.
IMPORTANT: Do not operate the levers

suddenly when the hydraulic oil
temperature is below 20°C (68°F). The
proper hydraulic oil temperature during
operation is 50 to 80°C (122 to 176°F), but
if operations must be performed at lower
temperatures, heat up the hydraulic oil
to at least 20°C (68°F). G4D005
3. Extend and retract each of the cylinders

Normal Warm-up
several times with no load.
L FC H
L3D008
1. Run the engine at medium speed (FC

mode) for about 5 minutes with no load.
4. Slew slowly left and right several times.
70
OPERATION
Machine Operation
Inspection After Warm-up

After warming up the engine and hydraulic
oil, perform the checks and inspections
described below, and repair if there is a
problem.
L FC H
5. Travel slowly forward and backward

several times.
Warming Up in Cold Weather

1. Perform the normal warm-up procedure.
L3D010
1. Check that the warning lamps and meters

are as follows:
¡ Are all the warning lamps off?
¡ Is the water temperature gauge’s
needle within the green range?
2. Check that there are no irregularities in
E4D011 the exhaust color, sound and vibrations.
2. Set the bucket cylinder at the stroke end
and keep it there.
Do not do this for more than 30 seconds.
3. Repeat step 2 until the bucket operating
speed is normal.
L3B030
3. Raise the safety lock lever to engage the

lock and check that the boom swing pedal,
operating and travel levers are locked.
71
OPERATION
Machine Operation
Operating the Travel Levers
WARNING
¡ Never allow anyone to enter the
slewing (swing) radius and machine
path.
¡ Signal your intention to move by L3D009
sounding the horn. 2. Fully lower the safety lock lever to

¡ There are blind spots to the rear of the disengage the lock.
machine.
If necessary, swing the cab around
before backing up to check that the
area is safe and clear.
30~40cm
E4D014
3. Fold the hoe attachment and lower it to

30 to 40 cm(12 to 16 in.) above the ground.
4. Lift the dozer blade.
¡ Before operating the travel levers, 5. Operate the left and right travel levers as
check to make sure that the dozer blade described below.
is to the front of the operator’s seat.
BE AWARE that when the dozer blade
is to the rear of the operator’s seat, the
travel levers operate in the opposite
Neutral Neutral
direction to when the dozer blade is in
the front.
¡ Remove any obstacles in the
machine’s path.
E4D015
Traveling Forward and Backward
When the dozer blade is in front of the
operator’s seat:
a To move forward:
L FC H Tilt the levers forward.
e To move backward:
Tilt the levers backward.
L3D011
1. Increase the engine speed.

72
OPERATION
Machine Operation
Pivot Turn
Neutral Neutral WARNING

Note that when the bucket is operated
while making a right pivot turn (i.e., when
only the left crawler is turning), the speed
of the pivot turn may suddenly increase.
E4D016
When the dozer blade is behind the

operator’s seat:
a To move forward:
Tilt the levers backward. Neutral
e To move backward:
Tilt the levers forward.
Traveling in 2nd (High) Speed

E4D017
WARNING Turning to the left when stopped:

a To turn forward to the left:
When a load greater than a set value is Tilt the right lever forward.
applied during 2nd speed (high speed) e To turn backward to the left:
travel, the speed will automatically slow Tilt the right lever backward.
down by switching to 1st speed (low To turn to the right, operate the left lever in
speed). Thereafter, when the load the same way.
Neutral
E4D018
Turning to the left while traveling:

a To turn left while traveling forward:
Set the left lever to neutral.
e To turn left while traveling backward:
Press the travel speed switch on the right Set the left lever to neutral.
travel lever to switch to 2nd (high) speed, To turn to the right while traveling, operate
and press it again to return to 1st speed (low the right lever in the same way.
speed).
73
OPERATION
Machine Operation
Spin Turn Stopping Travel
WARNING
Neutral
¡ Park the machine on firm, level ground
and apply the parking device. If you
must park on a slope or incline, block
the machine securely to prevent
movement.
E4D019 ¡ If any controls should be touched
a To spin left: accidentally when the safety lock lever
Tilt the left lever backward and the right is lowered, the machine will move
lever forward. suddenly, and cause serious injury or
e To spin right: death.
Tilt the right lever backward and the left ¡ Note that the dozer blade control is not
lever forward. locked, even when the safety lock lever
is set to the lock position. Do not touch
this control accidentally.
CAUTION
Never bring the machine to a sudden stop
except in the case of a true emergency.
Stop as gently as possible.
Neutral Neutral
E4D020
1. Slowly set the left and right travel levers

to the neutral position. The machine stops.
74
OPERATION
Machine Operation
Operating the Working Slewing

Equipment
WARNING
WARNING Check the surrounding area for safety
before slewing.
¡ Be careful to check which pattern of
lever control arrangement you are
operating with before beginning
operations.
¡ The explanations in this manual are for
the ISO pattern.
E4D021
a To slew left:
Tilt the left operating lever to the left.
e To slew right:
Tilt the left operating lever to the right.
C4D006 Operating the Boom

Use the right operating lever to operate the
boom and bucket.
Use the left operating lever to operate the
arm and for slewing.
Return the operating levers to the neutral
position to stop the hoe attachments.
1. Set the safety lock lever to the released E4D022
position.
a To lower the boom:
2. Set the pedal lock to the released position.
Tilt the right operating lever forward.
e To raise the boom:
Tilt the right operating lever backward.
75
OPERATION
Machine Operation
Operating the Arm Operating the Boom Swing
E4D023 C4D008
a To contract the arm: a To swing left:

Tilt the left operating lever backward. Press the left side of the pedal.
e To extend the arm: e To swing right:
Tilt the left operating lever forward. Press the right side of the pedal.
Operating the Bucket Operating the Dozer Blade
E4D024 E4D026
a To dig: a To lower the dozer blade:

Tilt the right operating lever to the left. Tilt the lever forward.
e To dump: e To raise the dozer blade:
Tilt the right operating lever to the right. Tilt the lever backward.
Operating the Intermediate Boom
L3D012
a To lower the intermediate boom:

Press the selector button and step on the
right side of the pedal.
e To raise the intermediate boom:
Press the selector button and step on the
left side of the pedal.
76
OPERATION
Machine Operation
Operating the First Auxiliary Operating With the Auxiliary Hydraulic

Buttons
Hydraulics
Use this to operate a breaker, crusher or
other attachment. A
Two methods of operation are permitted: B
operation with the auxiliary hydraulic buttons
and operation with the slider switch
(proportional control).
L3L035
S O a To deliver hydraulic oil to port (a):

Press (A).
e To deliver hydraulic oil to port (b):
Press (B).
b
a
L3C0012
Operating With the Slider Switch

(Proportional Control)
A
B
L3L021
a To deliver hydraulic oil to port (a):

Move the switch to the left (A).
e To deliver hydraulic oil to port (b):
Move the switch to the right (B).
77
OPERATION
Operating Procedures
Be Gentle on the Hydraulic Cylinders

Prohibited Operations
WARNING
¡ Do not operate on base rock (hard or
soft).
¡ Do not slew (swing) while traveling. If
you must operate the hoe attachment
while traveling, operate at speeds slow E4D031
enough so you have complete control
at all times. Do not extend the hydraulic cylinders to the
stroke ends. Operate them with leeway.
Do not perform breaking or leveling
operations using slew force
E4D029 Do not support the machine body with the

Do not break down walls or level ground hoe attachment as it is lowering with the arm
using slew force. Also, do not dig the bucket cylinder fully extended. Doing so
teeth into the ground during slewing. Doing concentrates the load on the arm cylinder
so will damage the hoe attachment. and could damage the arm cylinder.
Do not Dig while Traveling Do not Drive Piles with the Bucket or
Dig with it Using Shock Force
E4D030
E4D032
Do not dig the bucket into the ground and

use the traveling force to dig. Doing so will shorten the service life of the
hoe attachment. Use hydraulic force to dig.
78
OPERATION
Do not Perform Operations Using the Caution on Exposing the Dozer Blade to
Machine’s Dropping Force Shocks
E4D040
Hitting the dozer blade against rocks, etc.,

could damage the dozer blade or the blade
cylinder.
Caution on Folding the Hoe Attachment
E4D033
Putting excessive strain on the machine will

shorten its service life. Use the hydraulic
force of the cylinders and always dig with
shallow, long strokes.
E4D041
Digging Base Rock Be careful not to hit the bucket or dozer blade
when folding the hoe attachment.
Do not use the Dozer Blade as an Outrigger
E4D034
For hard base rock, break the rock up into

small pieces with a breaker, etc., before
digging. This prevents damage to the N0D009
machine and is thus more economical in the

end.
79
OPERATION
Pay Attention to the Dozer Blade when

Cautions on Operating
Digging
Cautions on Traveling
E4D0431
When digging deeply with the dozer blade E4A040
positioned at the front, be careful that the Traveling over obstacles (rocks, stumps, etc.)
boom cylinder and bucket do not hit the dozer may subject the body to strong shocks and
blade. result in damage. Avoid traveling over
Operate with the dozer blade at the rear obstacles whenever possible. If you must do
whenever possible. so, keep the hoe attachment near the ground,
travel at low speed, and go over the obstacle
Caution on Digging Down with the Dozer at the center of the crawler.
Blade
Cautions on Traveling in 2nd (High)
Speed
E4D044
This dozer blade is designed for simple earth

pushing. Do not dig down deeply with the E4D037
dozer blade. Doing so could damage the ¡ On uneven ground, travel at low speed
dozer blade and lower body. and avoid accelerating, stopping or
changing directions abruptly.
¡ When a load greater than a set value is
applied during 2nd speed (high speed)
¡ When traveling in 2nd speed, do so with
the dozer blade at the front.
80
OPERATION
Cautions on Use in Water

Cautions on Traveling on Slopes
WARNING
¡ Never exceed the machine’s stability
capabilities (maximum gradeability -
35°, lateral tipping angle - 15°). Also
note that when actual working area
E4D038 conditions are poor the machine’s
stability capabilities may be lower.
If you leave water at a sharp angle, the rear ¡ When traveling on slopes or grades,
of the machine may be submerged, exposing lower the bucket to a height of 20 to 30
the radiator fan to water and damaging them. cm (8 to 12 in.) off the ground. In
Do not let the rear of the machine get emergencies, lower the bucket to the
submerged. ground and stop the machine.
¡ When traveling on slopes or grades,
move slowly in first gear (low speed).
1 ¡ Do not travel down slopes in reverse.
E4D039
¡ Allowable water depth.

In water, only use the machine up to a
depth at which the water comes up to the
middle of the carrier roller (1). ¡ Do not change directions or cross
¡ When greasing places used under water slopes sideways. First return to a flat
for long periods of time, apply enough surface then redirect the machine.
grease so that the old grease is expelled. ¡ On grass, dead leaves, wet metal or
¡ Never submerge the slew bearing or main frozen surfaces, the machine may slide
body in water or sand. If the slew bearing sideways even on very gentle slopes.
or main body should get submerged, Make sure the machine never faces
contact a Takeuchi sales or service outlet sideways with respect to the slope.
for inspection.
81
OPERATION
Traveling Posture Braking when traveling down slopes

Traveling up slopes
Braking
E4D045E
When traveling down slopes, the brakes are

When traveling up slopes at an angle of 15° applied automatically when the travel levers
or greater, travel in the posture shown in the are returned to the neutral position.
diagram above.
If the crawlers slip
Traveling down slopes
Climbing
E4D046
If the crawlers slip while traveling up a slope,

When traveling down slopes at an angle of use the pulling force of the arm to climb the
15° or greater, lower the engine speed and slope.
travel in the posture shown in the diagram
above. If the engine stops
Descending
E4D047E
If the engine stops when traveling down a

slope, set the travel levers to the neutral
position, stop the machine, then start the
engine.
82
OPERATION
Do not open the door while traveling on

Getting Out of Mud
slopes
If the machine gets stuck in mud, use the
procedure below to get it out.
If one crawler is stuck
E4D048
Opening the door while traveling on slopes

is dangerous, as the force required to open
and close the door changes abruptly. Always
keep the door closed when traveling on
slopes. 1. Slew the bucket to the side which is stuck.
2. Set the arm and boom to an angle of 90
to 110°.
3. Press the bottom of the bucket (not the
teeth) against the ground.
4. Place a plank, etc., under the lifted crawler.
5. Lift the bucket and slowly move out of the
mud.
If both crawlers are stuck

1. Perform steps 1 to 4 above for both
crawlers.
2. Dig the bucket into the ground in front of
the machine.
3. Pull with the arm and travel forward
simultaneously to slowly move out of the
mud.
83
OPERATION
Operations Possible with this Digging Side Ditches

Machine
Excavating
80 ~120
C4D015
Use the boom swing function to dig side

ditches as shown in the diagram.
E4D0501
1. Set the dozer blade on the side opposite Loading

the side you want to dig on.
2. Use the arm and bucket and dig with
shallow, long strokes. The digging force
is strongest when the boom and arm angle
is 80 to 120°. Use this angle for effective
digging.
Digging Ditches
When loading dirt in a truck, starting from

the back of the truck’s bed makes for easier
loading and increases the amount of dirt that
can be loaded.
Also, use a small slewing angle for greater
efficiency.
E4D051
Mount a bucket suited for digging ditches and

set the crawlers parallel to the ditch to be
dug for greater efficiency.
When digging wide ditches, dig the sides first,
the center later.
84
OPERATION
Leveling
E4D053
1. Bring the hoe attachment close to the

body.
2. Gradually remove the dirt from the side of
the mound.
3. Once the mound is low, remove the dirt
from the top. If the load on the body is too
heavy, adjust by raising or lowering the
dozer blade.
85
OPERATION
Parking the Machine
Parking Inspection and Checks After

Stopping the Engine
WARNING 1. Check for oil and water leakage and
inspect the working equipment, covers
and lower body. If any irregularities are
found, repair.
2. Fill the fuel tank.
Refer to page 109 “Inspecting the Fuel
Level”.
3. Remove any paper scraps or dirt from the
engine room.
E3A4901
4. Remove any mud from the lower body.
¡ Park the machine on firm, level ground
and apply the parking device. Locking
¡ Before leaving the operator’s seat, Be sure to lock the following places:
raise the safety lock lever to engage
the lock and stop the engine. If any
controls should be touched
accidentally when the safety lock lever
is lowered, the machine will move
suddenly, and cause serious injury or
death.
1. Set the left and right travel levers to the

neutral position. ¡ Cab door
2. Press the decel. button and idle the engine ¡ Fuel filler cap
at low speed. ¡ Covers
3. Lower the bucket and dozer blade to the
ground.
4. Raise the safety lock lever to engage the
lock.
5. Stop the engine and remove the key.
Refer to page 67 “Stopping the Engine”.
When equipped with accumulator (option):

Refer to page 199 “Accumulator”.
86
OPERATION
Handling in Cold Weather
Preparing for Cold Weather Cautions after Completing

Operations
In cold weather, it may be difficult to start the
engine and the coolant may freeze. Make Heed the following in order to prevent dirt,
the preparations described below. water, or other objects stuck on the machine
as well as the lower body from freezing:
Changing the Fuel and Lubricant ¡ Remove any dirt or water from the body.
Change the fuel, hydraulic oil and engine oil In particular, water droplets on the
to types suited for cold conditions. hydraulic cylinder rod surfaces could
Refer to page 98 “Fuel and Lubricant Chart”. freeze, and if dirt enters into the seals
along with this, the seals could break.
¡ Park the machine on a dry, hard surface.
Engine Coolant If no appropriate place can be found, put
boards down and park the machine on
WARNING them.
¡ Drain any water from the fuel tank to
The coolant is combustible. Keep flames prevent freezing.
away. Refer to page 118 “Draining the Fuel
Tank”.
Use long-life coolant (antifreeze) and tap ¡ To prevent decreased battery
water for the engine coolant. performance, place a cover over the
Supplement: New machines are delivered battery or remove it from the machine and
with JIS Type 2 long-life coolant (antifreeze) store it in a warm place.
at a concentration of 50%. Also add battery fluid before starting the
Refer to page 98 “Fuel and Lubricant Chart”. next morning. If battery fluid is added after
completing operations, the distilled water
Battery may not mix, resulting in freezing.
As the temperature drops, the battery
performance decreases.
Inspect the battery. If the charge is low,
contact a Takeuchi sales or service outlet to After Cold Weather is Over
have the battery charged. Perform the following after cold weather is
Refer to page 117 “Inspecting the Battery over:
Fluid Level and Replenishing”. ¡ Change the fuel and the oils for the
different devices with those specified on
the Fuel and Lubricant Chart.
Refer to page 98 “Fuel and Lubricant
Chart”.
¡ When using one-season type antifreeze
coolant, completely drain the antifreeze
coolant, carefully clean the inside of the
coolant system, then add tap water.
Refer to page 124 “Cleaning the Engine
Cooling System”.
87
OPERATION
Handling Rubber Crawlers
Rubber crawlers have an inherent weakness

due to their use of rubber. Be sure to heed
the prohibitions and cautions below so as to
prevent damage to the crawlers and crawler
slippage.
Prohibited Actions
E4D057
Do not travel or operate the machine in the

¡ Do not let fuel, oil, salt or chemical solvents
following places:
get on the crawlers. These substances
may corrode the couplings of the crawlers’
metal cores, resulting in rust or peeling. If
these substances should get on the
crawlers, wipe them off immediately using
water.
E4D056
¡ Traveling or slewing on broken stone,

jagged base rock, iron rods, iron scraps
or the edges of iron sheets may damage
or cut the crawlers.
E4D058
¡ Traveling on roads directly after asphalting

or on hot surfaces such as over fires or
on iron sheets under strong sunlight may
result in irregular wear or damage of the
lugs.
¡ Do not move earth in places where the
rubber crawlers may slip. Doing so may
E4D055 speed up lug wear.
¡ Traveling on riverbeds or places with many
soft rocks may cause the crawlers to slip
off or be damaged due to rocks getting
stuck in them.
¡ Do not use on the seashore. The salt may
corrode the metal cores.
88
OPERATION
¡ Use rubber crawler belts at temperatures

Cautions
between –25°C to +55°C (–14°F to
Heed the following cautions when operating 131°F).
the machine: ¡ When storing the rubber crawlers for long
periods of time (3 months or more), do so
indoors in a place not exposed to direct
sunlight or rain.
L4D013
¡ Do not turn the undercarriage with the front

of the machine body lifted using the hoe
attachment and the upperstructure left in
this posture. Doing so will twist the crawler ¡ Rubber crawler belts are not as stable as
with the load concentrated on a single steel crawler belts since the entire lug is
point on the crawler belt, rapidly leading rubber. Be very careful when slewing and
to damage. swinging sideways.
¡ Avoid changing course abruptly and
spinning on concrete surfaces whenever Preventing the Rubber Crawlers from
possible. Slipping Off
Doing so may wear or damage the rubber Heed the following in order to prevent the
crawlers. rubber crawlers from slipping off:
¡ Avoid drops that may expose the rubber ¡ Always keep the crawlers at the proper
crawlers to strong shocks. tension.
¡ Salt, potassium chloride, ammonium
sulfate, potassium sulfate, and triple
superphosphate of lime can damage the
crawler belts. If any of these substances
should get on the crawler belts, wash them
off thoroughly with water.
¡ Do not let the sides of the rubber crawlers
rub against concrete or walls.
¡ Do not damage the rubber crawlers by
hitting the bucket against them.
¡ Be especially careful in the winter on ¡ When traveling up large cobblestone or
snowy or frozen surfaces as the crawler rock steps (20 cm (8 in.) or greater), climb
belts tend to slip. up the step at a direct angle and do not
change course on top of the step.
89
OPERATION
¡ When climbing in reverse, do not change

course at the point where the slope starts.
¡ Do not change directions when the crawler

belts are slack as shown in the diagram.
¡ Avoid traveling with one crawler on a slope

or projecting object and the other crawler
on a flat surface (with the machine at a tilt
of 10° or greater). Travel with both crawlers
on flat surfaces.
90
TRANSPORT
Loading and Unloading ............................. 92
Hoisting the Machine ................................. 93
Securing the Machine ................................ 94
Cautions on Transporting .......................... 94
91
TRANSPORT
Loading and Unloading
1. Apply the truck’s parking brake and place

WARNING
stoppers against its tires.
The machine may roll or tip over or fall 2. Fasten the ramps securely to the truck bed
while loading or unloading it. Take the so that they will not come off. Set the
following precautions: ramps to an angle of 15° or less.
¡ Select a firm, level surface and keep 3. Line up the center of the truck bed with
sufficient distance from road the center of the machine and the center
shoulders. of the ramps with the center of the
¡ Use loading ramps of adequate crawlers.
strength and size. Maintain the slope 4. Make sure the dozer blade does not hit
of loading ramps within 15 degrees. the ramps.
¡ Keep the truck bed and loading ramps 5. Lower the hoe attachment as much as
clean of oil, clay, ice, snow, and other possible, making sure it will not hit the
materials which can become slippery. truck.
Clean the tracks. 6. Lower the engine speed.
¡ Never change course on the ramp.
¡ Do not slew (swing) on ramps. The
machine may tip over.
¡ When slewing (swinging) on the truck
bed, do so slowly as the footing can
be unstable.
When loading or unloading the machine, be

sure to use ramps and following the
procedure below.
Fasten to the suspension fitting
Ramp
Stopper
15° or less
Distance between ramps E4F001
7. Determine the direction on the ramps, then

slowly travel up or down the ramps in 1st
speed (low speed), following the signals
of a flagman.
8. Load the machine properly at the
prescribed position on the bed.
Refer to page 94 “Transporting Posture”.
92
TRANSPORT
Hoisting the Machine
Hoisting
WARNING
1. Slew the upper structure so that the dozer
¡ Know and use correct crane signals. blade is positioned to the rear of the body
¡ Inspect the hoisting equipment daily (so that the crawler frame and upper
for damaged or missing parts. structure are parallel).
¡ When hoisting, use a wire rope with 2. Raise the dozer blade fully.
sufficient strength with respect to the 3. Fully extend the bucket and arm cylinders
machine’s weight. and fully raise the boom.
¡ Do not hoist with the machine in a
4. If the boom is swung to either the left or
posture other than the one described
in the procedure below. Doing so is right side, set it so that it is straight ahead.
dangerous as it may result in the 5. Raise the safety lock lever to engage the
machine losing its balance. lock.
¡ Do not hoist the machine with an 6. Stop the engine and remove the starter
operator (s) on it. key and get off the machine.
¡ When hoisting, hoist slowly so that the 7. Install the sling as shown on the diagram
machine does not tip. below.
¡ Keep all other persons out of the area Suspend in such a way that the sling and
when hoisting. Do not move the Lifting tool do not touch the body.
machine over the heads of the persons.
8. Hoist slowly until the machine just leaves
IMPORTANT: This hoisting method applles the ground.
to machines with standard specifications. 9. Stop hoisting until the machine is stable
The center of gravity differs according to and hoist slowly.
the attachments and options that are
mounted.
Consult a Takeuchi sales or service outlet.
Hoisting posture
4000mm(157.5 in.)
34 4000mm(157.5 in.)
26 13
3300mm(130 in.)
L3F001
93
TRANSPORT TRANSPORT
Securing the Machine Cautions on Transporting
After loading the machine in the designated

position, secure it as described below.
Transporting Posture
Wire rope Padding
E4F002
1. Lower the dozer blade.

WARNING
2. Fully extend the bucket and arm cylinders,
then lower the boom. ¡ Know and follow the safety rules,
3. Stop the engine and remove the starter vehicle code and traffic laws when
key. transporting the machine.
4. Raise the safety lock lever to engage the ¡ Consider the length, width, height and
lock. weight of the truck with the machine
5. Set stoppers in front and behind the loaded on it when determining the best
crawlers. route.
6. Put a chain or wire rope over the lower
frame and fasten it securely to prevent
sideways slippage.
7. Secure the bucket with a chain or wire
rope.
IMPORTANT: Place a wooden block

under the bucket so that it is not damaged
by hitting the floor.
94
MAINTENANCE
General ....................................................... 96
Service Data ............................................... 98
Important Parts ........................................ 102
Maintenance Chart ................................... 103
Walk-Around Inspection .......................... 105
Daily Inspection (Every 10 Hours) ........... 107
After First 50 Hours
(New Machines Only) ...................... 112
Every 50 Hours ......................................... 115
After First 250 Hours
(New Machines Only) ...................... 119
Every 250 Hours ....................................... 120
Every 500 Hours ....................................... 122
Every 1000 Hours ..................................... 124
Every 2000 Hours ..................................... 127
When Required ........................................ 130
Long-term Storage ................................... 140
95
MAINTENANCE
General
Maintenance Description Cautions on Maintenance

For long-term use of the machine under good Do not perform inspection and maintenance
conditions, perform the inspection and procedures not prescribed in this manual.
maintenance procedures properly and safely Have inspection and maintenance
as recommended in this manual. procedures not prescribed in this manual
performed by a Takeuchi sales or service
The inspection and maintenance items are outlet.
divided according to the machine’s total
operating time (inspection and maintenance Always keep the machine clean.
to be performed every 10 hours (walk-around ¡ Always keep the machine clean, and wash
and daily inspection), every 50 hours, every it before performing inspection and
250 hours, etc.). Refer to the hour meter to maintenance.
determine when it is time to perform ¡ When washing the machine with water,
inspection and maintenance. Items for which stop the engine and cover the electrical
it is not possible to determine the inspection system with plastic to protect it from water.
and maintenance interval are included under Exposing the electrical system to water is
“When Required”. dangerous and could result in short-
circuits or malfunction. Do not wash the
When operating the machine in extremely battery, sensors, connectors or the inside
harsh environments (with high dust levels or of the cab with water or steam.
high temperatures), inspection and
maintenance should be performed earlier Fuel, lubricant and grease
than the times indicated on the Maintenance ¡ For fuels, lubricant and grease, follow the
Chart. instructions on the “Fuel and Lubricant
Chart”.
¡ Use pure fuels, lubricants and greases
which do not contain water, and be careful
to keep dirt out when changing or
replenishing fuel, lubricant or grease.
¡ Store fuels, lubricants and greases in the
prescribed places and in such a way that
no water or dirt can get in them.
Cautions on fueling
¡ If the port includes a strainer, do not
remove the strainer when fueling.
¡ After fueling, be sure to securely tighten
the cap, etc.
¡ Do not add more than the prescribed
amount of fuel.
96
MAINTENANCE
General
Do not clean parts with fuel. Disposing of wastes

Do not use fuel to clean parts. Use a non- ¡ Collect spent fluids from the machine in
combustible cleaning agent. containers. Disposing of wastes
irresponsibly damages the environment.
Keep dirt out. ¡ Dispose of oil, fuel, cooling water, coolant,
When mounting and removing parts, do so filters, batteries and other harmful
in a place where there is no dust, clean the substances as prescribed by law.
working area and the part, and keep dirt out.
Check after maintenance
Clean mounting surfaces. ¡ Gradually increase the engine speed from
When mounting and removing parts, be sure a low idle to maximum speed and check
that the surfaces of contact of the parts are that there is no oil or water leaking from
clean. If the sealing grooves of the surface serviced parts.
of contact are damaged, consult a Takeuchi ¡ Operate all the operating levers and check
sales or service outlet. that the machine is operating properly.
Seals and split pins Cautions on handling of battery cables

¡ Replace removed seals and split pins with ¡ Disconnect the battery cables (+,-) before
new ones. working on the electrical system or doing
¡ When mounting, be careful not to damage any welding.
or twist the seal. Remove the negative (-) battery cable first.
When reconnecting the battery, connect
Sealing tape the negative (-) battery cable last.
¡ Do not disconnect the battery cables while
Sealing tape the engine is running. Doing so could
damage the electronic circuitry of the
alternator and other parts.
Leave 1 or 2 threads free

E4G001
¡ When wrapping sealing tape around

plugs, etc., remove any old sealing tape
from the threads and clean the threads.
¡ Wrap the sealing tape tight, leaving 1 or 2
threads at the tip free.
97
MAINTENANCE
Service Data
Fuel and Lubricant Chart

Use different fuels, lubricants and greases according to the temperature, referring to the
chart below.
¡ Change the lubricant earlier than as shown in the table if it is extremely dirty or its
performance has deteriorated severely.
¡ Whenever possible, use the same brand of lubricant as before. If changing with a different
brand, replace the entire quantity – do not mix different brands.
Type by temperature
Replacement Capacity
Part Type -22 -4 14 32 50 68 86 104°F
-30 -20 -10 0 10 20 30 40 °C interval Lit. (US. qt.)
Upper limit:
Diesel SAE 5W-20
Engine
engine oil After first 50 hrs. 10.2 (10.8)
SAE 10W-30
oil pan Every 250 hrs. Lower limit:
API-CD SAE 15W-40
5.7 (6)
Antiwear System:
hydraulic oil ISO VG32 132
Hydraulic (34.9 US.gal.)
(Option: ISO VG46 Every 2000 hrs.
tank
Biodegradable ISO VG68 Tank:
oil) 68 (18 US.gal.)
Use a clean, Quality fuel for good performance and optimum engine life.
¡To prevent fuel flow problems in cold weather, use diesel fuel with a pour point of 120
Fuel tank Diesel fuel at least -12°C (10°F) below the lowest expected ambient temperature.
¡Minimum cetane number is 45. Low temperature or high altitude operation may (31.7 US.gal.)
require the use of fuel with a higher cetane number.
Engine Coolant
50% coolant mixture
cooling (water + Every 1000 hrs. 9.5 (10)
system coolant)** 30% coolant mixture 11.2 (11.8)***
Travel
reduction Gear oil After first 250 hrs.* 1.5 (1.6)
SAE 90
gear API-GL-4 Every 1000 hrs.
Slew
Lithium Every 50 hrs.
bearing
based
Working grease Daily or every As
equipment EP-2 10 hrs. required
Levers NLGI No. 2 When required
* : If the percentage of the traveling time within the total operating time is high, replace the
gear oil earlier than the specified time.
** : For water, use tap water (soft). Do not use well or river water.
When the ambient temperature drops below 0°C, supply coolant (antifreeze). Follow the
coolant manufacturer’s instructions to determine the mixture ratio.
*** : Serial No. 17514412 ~
98
MAINTENANCE
Service Data
Replace the hydraulic oil regularly!

When using a hydraulic breaker, the oil ¡ Clean the suction strainer when changing
deteriorates quicker than during normal the return filter element.
digging. Be sure to replace the hydraulic oil
and return filter element. Replacement Interval (Hours)
¡ Failure to replace these in time can lead
to damage to the machine and breaker’s Item Hydraulic Oil Filter Element
hydraulic systems. In order to improve the 1st time 25
service life of the hydraulic systems, be 2nd time 100
sure to replace the hydraulic oil and return
Periodically 600 200
filter element according to the following
chart of the replacement interval. When the breaker operating ratio is 100%
Refer to page 193 “Hydraulic Breaker”.
Expendables
Replace expendables such as filters and elements periodically, referring to the table below.
Item Part name Part No. Replacement interval
Hydraulic oil return Element 15511-02600 After first 50 hrs.

filter Every 500 hrs.
Fuel filter Cartridge 119802-55800

Every 500 hrs.
Water separator filter Cartridge 129901-55850
Engine oil filter Cartridge 129150-35152 After first 50 hrs.

Every 250 hrs.
Air cleaner Outer Element 129062-12560 Every 1000 hrs. or

after 6 cleanings
(whichever comes
first)
Inner Element 119005-12571 Every 1000 hrs. or

after 3 cleanings of
the outer element
(whichever comes
first)
Air breather filter Element 15520-00902 Every 1000 hrs.
99
MAINTENANCE
Service Data
Tools
No. Part name Part No. Remarks No. Part name Part No. Remarks
1 Spanner 19100-47081 10-12 13 Spanner 16901-00041 41
2 Spanner 19100-47082 14-17 14 Hex. wrench 16906-00250 2.5mm
3 Screwdriver 19100-06112 (+) (–) 15 Hex. wrench 16906-00500 5mm
4 Filter wrench 19100-65081 16 Hex. wrench 16906-00600 6mm

5 Hammer 16903-00330 3/4 17 Hex. wrench 16906-00800 8mm
6 Monkey wrench 16904-00250 250mm 18 Hex. wrench 16906-01000 10mm
7 Pliers 16905-00200 200mm 19 Hex. wrench 16906-01200 12mm

8 Spanner 16900-01013 10-13 20 Tool case 16914-00001
9 Spanner 16900-01922 19-22 21 Case 16919-00001
10 Spanner 16900-02427 24-27 22 Grease gun 16910-60600 600cc

11 Spanner 16900-02730 27-30 23 Drain connector 15545-12601
12 Spanner 16900-03236 32-36
100
MAINTENANCE
Service Data
Tightening Torques
Nuts and Bolts (for ISO strength category 10.9)
Tighten nuts and bolts at the torques shown on the table below, unless otherwise specified in
the text.
¡ Tightening torques when mounting plastic covers differ from the values on the table below.
Consult a Takeuchi sales or service outlet. Tightening too strongly will break the cover.
¡ When replacing nuts and bolts, replace them with nuts and bolts of the same size and
standards.
¡ Tighten nuts and bolts alternately (top, bottom, left then right) or in 2 or 3 times so that they
are tightened uniformly.
3 6
5 4
2 E4G003
Head width Torque

Size (a) X Pitch
Thread (b) General Connection Points
mm mm N·m ft-lb
10 M6 X 1.0 9.8 ± 0.5 7.2 ± 0.4
12, 13 M8 X 1.25 22.6 ± 1.1 16.6 ± 0.8
14, 17 M10 X 1.5 47.1 ± 2.4 34.7 ± 1.7
Coarse 17, 19 M12 X 1.75 83.4 ± 4.1 61.5 ± 3.0
19, 22 M14 X 2.0 134.4 ± 6.7 99.1 ± 4.9
22, 24 M16 X 2.0 207.9 ± 10.4 153.3 ± 7.7
27, 30 M20 X 2.5 410.9 ± 20.5 303.1 ± 15.1
12, 13 M8 X 1.0 24.5 ± 1.2 18.1 ± 0.9
14, 17 M10 X 1.25 50 ± 2.5 36.9 ± 1.8
17, 19 M12 X 1.5 87.3 ± 4.3 64.4 ± 3.2
Fine
19, 22 M14 X 1.5 135.3 ± 6.8 99.8 ± 5.0
22, 24 M16 X 1.5 220.6 ± 11 162.7 ± 8.1
27, 30 M20 X 1.5 452.1 ± 22.6 333.4 ± 16.6
101
MAINTENANCE
Important Parts
For safe use, the machine must be serviced periodically. To increase safety, periodically
replace the parts listed in the following table of important parts.
Serious injury or a fire could result if they deteriorate or are damaged.
Table of Important Parts
Unit Important parts to be replaced periodically Replacement Interval
Fuel system Fuel hoses
Packing in fuel filler cap
Engine connection Engine oil filter hoses
Heater hoses
Heater & AC systems
Air conditioner hoses
Hydraulic hoses ( Pump - delivery )
Machine Hydraulic hoses ( Pump - suction )
body Hydraulic hoses ( Slew motor )
Hydraulic hoses ( Travel motor )
Hydraulic hoses ( Boom cylinder lines ) Every 2 years
Hydraulic Hydraulic hoses ( Boom adjustment cylinder lines )
system Hydraulic hoses ( Arm cylinder lines)
Hydraulic hoses ( Bucket cylinder lines )
Working
Hydraulic hoses ( Swing cylinder )
equipment
Hydraulic hoses ( Blade cylinder )
Hydraulic hoses ( Tension cylinder )
Hydraulic hoses ( Pilot valve )
Hydraulic hoses ( Auxiliary lines )
Seat belt Every 3 years
Above important parts are vulnerable to aging and wear or deterioration and it is difficult to
determine the degree to which they have deteriorated on the occasion of periodic service. To
maintain their proper function at all times, therefore, replace them with new ones after using
them for a specific period of time even if no abnormality is found with the parts. If you find
abnormalities in these parts before their scheduled replacement time is reached, repair or
replace them immediately. If a hose clamp is deformed or cracked, replace it immediately.
When replacing the important parts, please contact a Takeuchi sales or service outlet.
Also check the hydraulic hoses other than the above important parts. If any abnormality is
found in them, retighten them or replace them immediately.
When replacing the hydraulic hoses, replace the O-rings and seals at the same time.
Check the fuel and hydraulic hoses according to the periodic schedule described below.
Refer to “Maintenance”.
Type of inspection Inspection item
Daily inspection Leakages from joints, hydraulic or fuel hoses.
Monthly inspection Leakages from joints, hydraulic or fuel hoses.
Damaged hydraulic or fuel hoses(cracks, wear and tear).
Annual inspection Leakages from joints, hydraulic or fuel hoses.
Deteriorated, twisted, damaged hydraulic or fuel hoses (cracks, wear
and tear) or hoses in contact with other parts of the machine.
102
MAINTENANCE
Maintenance Chart
Maintenance Items See page

Walk-Around Inspection
Inspecting by opening the engine hood and covers 105
Inspecting by walking around the machine 106
Inspecting while sitting in the operator’s seat 106
Daily Inspection (Every 10 Hours)
Inspecting and replenishing the coolant 107
Inspecting and replenishing the engine oil 108
Inspecting the water separator 108
Inspecting the fuel level 109
Inspecting the hydraulic oil level and replenishing 109
Lubricating the working equipment 111
After First 50 Hours (New Machines Only)
Replacing the hydraulic oil return filter 112
Replacing the engine oil and oil filter 113
Inspecting and adjusting the fan belt 114
Every 50 Hours
Inspecting the crawler tension 115
Lubricating the slew bearing 116
Inspecting the battery fluid level and replenishing 117
Draining the fuel tank 118
Replacing the travel motor gear oil* 119
Every 250 Hours
Replacing the engine oil and oil filter 120
Inspecting and adjusting the fan belt 120
Cleaning the air cleaner 120
Cleaning the radiator fins and oil cooler fins 121
* If the percentage of the traveling time within the total operating time is high, replace the
gear oil earlier than the specified time.
103
MAINTENANCE
Maintenance Chart
Maintenance Items See page

Every 500 Hours
Replacing the hydraulic oil return filter 122
Replacing the fuel filter 122
Replacing the water separator filter 123
Every 1000 Hours
Cleaning the engine cooling system 124
Replacing the air cleaner elements 125
Replacing the travel motor gear oil 126
Replacing the air breather filter 126
Inspecting and adjusting the engine valve clearance 126
Retightening the engine cylinder head bolts 126
Inspecting the engine fuel injection pressure and spray condition 126
Every 2000 Hours
Replacing the hydraulic oil and cleaning the suction strainer 127
Inspecting the engine fuel injection timing 129
Inspecting the engine fuel injection valve 129
When Required
Replacing the bucket teeth and the side cutters 130
Adjusting the gap between the bucket and arm 132
Inspecting and replenishing the windshield washer fluid 133
Draining the water separator 133
Replacing the bucket 134
Lubricating the levers 136
Inspecting the rubber crawlers 137
Replacing the rubber crawlers 138
104
MAINTENANCE
Perform the following inspections once every day before starting the engine the first time.
WARNING
¡ Before operating, perform the walk-around inspections and make repairs
immediately should any irregularities be found.
¡ Be sure to secure the engine hood or cover when opening it. Do not open the engine
Before starting the engine, look around the machine and lower body, clean any combustible
materials off high temperature parts of the engine, and inspect for such irregularities as oil
leakage, water leakage and looseness of nuts and bolts.
15 11 12
2 1
3 8 5
13
4
14
10
7 6
L3G003
Inspecting by Opening the

Engine Hood and Covers
1. Check for any twigs, leaves, oil or other 3. Check for oil leakage from the hydraulic
combustible materials around the engine tank, hydraulic devices, hoses and
and battery. connections.
2. Check for oil or engine coolant water
leakage around the engine.
105
MAINTENANCE
Inspecting by Walking Around Inspecting While Sitting in the

the Machine Operator’s Seat
4. Check lights for dirt, damage and burnt 13. Check the windshield for dirt or damage.
out bulbs. 14. Check the seat and seat belt for dirt or
5. Check attachments and hoses for damage.
damage. Check the operator’s seat for dirt, oil or
6. Check the bucket, bucket teeth and side other combustible materials.
cutter for wear, damage and looseness. 15. Check the monitor, instruments and
7. Check the hook, slip stopper and hook switches for dirt or damage.
mount of buckets with hooks for damage.
(Option)
8. Check the handrail and step for damage
and loose bolts.
9. Check the crawler, carrier roller, track
roller, idler and sprocket for damage, wear
and loose bolts.
10. Check for oil leakage from the travel
motor.
11. Check the canopy, cab and guard for
damage and loose nuts and bolts.
Check the rear view mirror and room
mirror for dirt, damage, and angle
adjustment.
12. Check the labels for dirt and damage.
106
MAINTENANCE
Perform the following inspections once every day before starting the engine the first time.
WARNING
¡ Before operating, perform the Daily inspections and make repairs immediately should
any irregularities be found.
¡ Be sure to secure the engine hood or cover when opening it. Do not open the engine
Inspecting and Replenishing the Replenishing

Coolant 1. Remove the reserve tank’s cap (2).
2. Supply coolant up to the upper limit (H) of
WARNING the reserve tank (1).
If the reserve tank is empty, inspect for
Do not remove the radiator cap or drain fluid leakage, then inspect the radiator (3)
plugs when the coolant is hot. Stop the coolant level. If it is low, supply water to
engine, let the engine and radiator cool the radiator (3) first, then to the reserve
and loosen the radiator cap or drain plugs tank.
slowly. 3. Install the cap (2).
Inspection
3 2
FULL
1
LOW
H
L
L3G004
1. Open the engine hood and left side cover.

2. Inspect the quantity of coolant in the
reserve tank (1).
The level should be between the upper
limit (H) and lower limit (L).
If it is below the lower limit (L), replenish.
107
MAINTENANCE
Inspecting and Replenishing the Inspecting the Water Separator

Engine Oil
WARNING
6
¡ Stop the engine and allow the machine
to cool down before performing
maintenance.
L3G027
support your body at three points with 1. Turn the starter switch to the ON position.
your hands and feet. 2. Inspect the water separator warning lamp
(6).
Inspection 3. If an alarm is sounded or a warning lamp
starts flashing, drain the water.
2 L H 1 Refer to page 133 “Draining the Water
Separator”.
L3G005
1. Open the engine hood.

2. Pull out the dipstick (1) and wipe off the
oil with a rag.
3. Fully reinsert the dipstick (1), then pull it
back out.
4. Check the oil on the dipstick (1).
The level should be between the upper
limit (H) and lower limit (L).
Replenishing
1. Remove the oil supply cap (2).
2. Supply oil up to the upper limit (H) of the
dipstick (1).
Problems could arise if the oil level is either
too low or too high.
3. Tighten the oil supply cap (2).
4. Start the engine, run it at low idle for about
3 minutes, then stop it.
5. After about 10 minutes, inspect the oil
level.
108
MAINTENANCE
Inspecting the Fuel Level Inspecting the Hydraulic Oil Level

and Replenishing
WARNING
WARNING
steps and handrails when climbing on ¡ Never jump off the machine. Use the
and off the machine, and always steps and handrails when climbing on
support your body at three points with and off the machine, and always
your hands and feet. support your body at three points with
¡ Do not smoke or permit open flames your hands and feet.
while fueling or near fueling ¡ Oil may spurt out if caps or filters are
operations. removed or pipes disconnected before
¡ Stop the engine in a well-ventilated releasing the pressure in the hydraulic
place when supplying fuel. system.
¡ Clean up spilled fuel immediately. • Gradually press the air breather
¡ Do not fill the fuel tank to capacity. button to relieve tank pressure.
Allow room for expansion.
¡ Tighten the fuel filler cap securely. Inspection
The oil level changes according to the oil
temperature. Inspect the oil level in the
2 1 hydraulic oil level inspection posture shown
in the diagram.
¡Hydraulic oil level inspection posture
6 H
3
L3G006 L
1. Check the fuel level using the fuel gauge
(1).
F: full
L3G007
E: empty
2. If the level is low, supply fuel from the fuel 1. Start the engine and run it at low speed.
port (2) while watching the fuel gauge (1). 2. Fully retract the arm and bucket cylinders
Refer to page 42 “Fuel Filler Cap”. and ground the bucket.
3. Ground the dozer blade, then stop the
engine.
4. Inspect the oil level using the sight gauge
(6).
¡When the oil temperature is about 20°C
(68°F):
The level should be halfway between the
upper limit (H) and lower limit (L).
109
MAINTENANCE
¡ When the oil temperature is about 50 to

80°C (122 to 176°F):
The level should be near the upper limit
(H).
Replenishing
4 2
10
5 3
8
1
9
7
L3G008
1. Remove cap nut (2).

2. Press button (3) and bleed the air from
the tank.
3. Tighten securely by hand with cap nut (2).
4. Remove the plug (10).
5. Supply hydraulic oil up to the middle of
the sight gauge (6).
6. Tighten the plug (10).
110
MAINTENANCE
Lubricating the Working Equipment
1. Set the machine to the lubrication posture shown in the diagram above, ground the working
equipment, then stop the engine.
2. Use the grease gun to lubricate the grease nipples.
3. Wipe off the expelled grease.
111
MAINTENANCE
Replacing the Hydraulic Oil 4 2

Return Filter
10
5 3
WARNING 8
1
¡ Stop the engine and allow the machine 9
maintenance.
• The engine, hydraulic lines and many
other parts of the machine are hot 6
directly after the engine is stopped.
Touching these parts will cause
burns.
• The hydraulic fluid is also hot and
under high pressure. 7
Be careful when loosening caps and L3G008
plugs. Working on the machine under 1. Remove cap nut (2).

these conditions could result in 2. Press button (3) and bleed the air from
burns or injuries due to the hot oil the tank.
spurting out. 3. Tighten securely by hand with cap nut (2).
¡ Never jump off the machine. Use the 4. Loosen the bolts, and remove the flange
steps and handrails when climbing on (4).
and off the machine, and always 5. Remove the return filter (5).
support your body at three points with 6. Install the new return filter.
your hands and feet. 7. Install the flange (4).
¡ Oil may spurt out if caps or filters are 8. Inspect the level with the sight gauge (6),
removed or pipes disconnected before and replenish if the level is low.
releasing the pressure in the hydraulic Refer to page 109 “Inspecting the
system. Hydraulic Oil Level and Replenishing”.
• Gradually press the air breather
button to relieve tank pressure.
• When removing plugs or screws or
disconnecting hoses, stand to the
side and loosen slowly to gradually
release the internal pressure before
removing.
112
MAINTENANCE
Replacing the Engine Oil and Oil 2. Loosen the bolts and remove the under
cover.
Filter
3. Place a pan for catching the spent oil
under the drain plug (3).
WARNING
4. Remove cap (A), install connector (B) and
¡ Stop the engine and allow the machine drain the oil. (The oil comes out when the
to cool down before performing screw is tightened.)
maintenance. 5. Remove connector (B) and install cap (A).
• The engine, muffler, radiator and
many other parts of the machine are IMPORTANT: Check the spent oil. If it
hot directly after the engine is contains large amounts of metal powder,
stopped. Touching these parts will consult a Takeuchi sales or service outlet.
cause burns.
• The engine oil is also hot. 6. Install the under cover.
Be careful when loosening caps and
plugs. Working on the machine under
these conditions could result in
burns.
4
your hands and feet. L3G030
7. Open the maintenance cover.

2 L H 1 8. Using a filter wrench, turn the filter (4)
counterclockwise and remove it.
9. Clean the surface of installation of the filter
stand.
10. Apply a thin layer of oil to the packing of
the new filter.
11. Install the new filter by hand.
L3G005
12. Tighten 3/4 more turn with the filter
1. Open the engine hood and remove the oil wrench after the filter packing comes in
supply cap (2). contact with the surface of installation.
13. Supply oil up to the upper limit (H) of the
dipstick (1). Problems could arise if the
oil level is either too low or too high.
14. Tighten the oil supply cap (2).
15. Start the engine, run it at low idle for about
3 minutes, then stop it.
B A 16. After about 10 minutes, inspect the oil
level.
3
L3G025
113
MAINTENANCE
Inspecting and Adjusting the Fan Adjustment

Belt
WARNING
Stop the engine and allow the machine
inspection and maintenance.
¡ The engine, muffler, radiator, hydraulic
lines, sliding parts and many other
parts of the machine are hot directly 1. Loosen the locking nut (6).
after the engine is stopped. Touching 2. Turn the adjustment bolt (5) and adjust the
these parts will cause burns. fan belt (4).
• Tighten: Clockwise
Inspection • Loosen: Counterclockwise
1. Open the engine hood. 3. Tighten the locking nut (6).
2. Press at the center of the fan pulley (2)

and alternator pulley (3) and check the
tension (about 98 N or 22 lbs.).
The slack (A) should be about 7 to 10 mm
(0.28 to 0.4 in.).
3. Inspect the fan belt (4) and replace it if:
• there are cuts or cracks.
• the belt is worn and touches the bottom
of the V groove in the pulley.
• the belt stretches and cannot be
adjusted.
114
MAINTENANCE
Every 50 Hours
Inspecting the Crawler Tension A B
WARNING
If you must work beneath the raised
machine or equipment, always use wood
blocks, jack-stands or other rigid and
stable supports. Never get under the E4G0201
machine or working equipment if they are 2. Use the operating devices to lift the body.
not sufficiently supported. This Operate the levers slowly.
procedure is especially important when
working on hydraulic cylinders.
Inspection
A B
3. Inspect the gap (A or B) between the

E4G0192 bottom surface of the frame at the center
of the crawler frame and the top surface
1. For rubber crawlers, move the machine of the crawler.
so that the “M” or “∞” mark at the coupling The gap (A or B) should be within the
is at the top center of the crawler frame. following range:
(A) Rubber crawler:
160 to 180 mm (6.3 to 7.1 in.)
(B) Steel crawler:
260 to 280 mm (10.2 to 11.0 in.)
(B) Segment rubber crawler:
245 to 265 mm (9.6 to 10.5 in.)
Adjustment
This machine uses a hydraulic cylinder to
adjust the tension of the crawler belts. Note
that it is not necessary to regularly perform
adjustments of the tension of the belt itself.
115
MAINTENANCE
Every 50 Hours
5. Repeat steps 2 to 4 above three times.

Lubricating the Slew Bearing
6. Wipe off the grease expelled from the slew
bearing and grease nipple.
WARNING
Do not slew while lubricating. Doing so
is dangerous, as you may get caught in
the machine.
L3G011
1. Stop the engine with the machine in the

posture shown on the diagram above.
1
L3G012
2. Use the grease gun to supply grease to

the grease nipple (1).
E4G026
3. Start the engine, lift the bucket and slew

clockwise 90°.
4. Ground the bucket and stop the engine.
116
MAINTENANCE
Every 50 Hours
Inspecting the Battery Fluid Level

and Replenishing
DANGER
¡ Do not use the battery when the fluid
level is below the lower level. Doing so
will hasten the deterioration of the
internal portions of the battery and
2. Inspect the indicator (1).
shorten the battery life, and can also
• Blue: Good
cause rupturing (or an explosion).
• White: Charging needed
¡ Batteries generate flammable and
• Red: Insufficient battery fluid
explosive gases. Keep arcs, sparks,
3. Inspect the fluid level.
flames and lighted tobacco away.
The fluid level should be between the lines
¡ Use a dampened cloth to clean the area
indicating the upper level (H) and lower
of the fluid level lines and check the
level (L). If not, add distilled water up to
fluid level. Note that if this area is
line (H).
cleaned with a dry cloth, static
¡ If the fluid level can not be checked by
electricity could cause ignition or
fluid level lines.
explosion.
WARNING
¡ Do not fill the battery above the upper
level. Doing so could cause the fluid
to leak, contact and damage the skin,
or cause parts to corrode.
¡ Batteries contain sulfuric acid which
will damage eyes or skin on contact.
• If acid contacts eyes, flush Remove the caps (2) and look into the fluid
immediately with clean water and get supply holes to check the fluid level. If the
prompt medical attention. fluid is below the sleeve (3), be sure to add
• If acid is accidentally swallowed, distilled water up to the bottom edge of the
drink large quantities of water or milk sleeve (3).
and call a physician immediately. Proper amount .... (A)
• If acid contacts skin or clothing, wash The fluid reaches up to the bottom edge
off immediately with clean water. of the sleeve (3), so the surface tension
causes the fluid to swell and the plate
Inspection appears distorted.
IMPORTANT: Check the fluid level of all Level too low ....... (B)
cells, even when the fluid level can be The fluid does not reach up to the bottom
checked by indicator. edge of the sleeve (3), so the plate
appears laminar, not distorted.
1. Open the left side cover. 4. Also check the terminals for looseness and
dirt.
117
MAINTENANCE
Every 50 Hours
Replenishing
Draining the Fuel Tank
When adding distilled water, do so before
starting operations in order to prevent
freezing. WARNING
1. Remove the caps (2), and add distilled ¡ Never jump off the machine. Use the
water until the upper level (H). steps and handrails when climbing on
2. Inspect the indicator (1) then it turns blue. and off the machine, and always
3. Clean the cap’s exhaust hole, then tighten support your body at three points with
the caps (2) securely. your hands and feet.
while handling fuel or working on the
fuel system.
¡ Stop the engine in a well-ventilated
place and allow it to cool down before
performing maintenance.
Do this before operating the machine.
2 1
3
L3G006
1. Remove the fuel filler cap (2).

2. Place a pan under the drain cock (3).
3. Open the drain cock (3) and drain the water
and sediment from the bottom of the tank.
4. Close the drain cock (3).
5. While watching the fuel gauge (1), supply
fuel.
6. Tighten the fuel filler cap (2) supply lock it
with the key.
7. Bleed the air.
Bleeding the air from the fuel system

Refer to page 145 “Bleeding the Air from the
Fuel System”.
Supplement: Air in the fuel system can
make it difficult to start the engine and cause
engine problems. Also bleed the air when
the fuel tank is emptied.
118
MAINTENANCE
Replacing the Travel Motor Gear

Oil 3
WARNING 2
to cool down before performing 1
maintenance. L3G015
• The travel motors are hot directly
1. Set the travel motor so that plug (1) is at
after the engine is stopped. Touching
the very bottom.
them will cause burns.
• The gear oil is also hot and under
under plug (1).
high pressure.
3. Remove plugs (1), (2) and (3) and drain
Be careful when loosening plugs.
the oil.
Working on the machine under these
4. Wrap new sealing tape around the plugs.
conditions could result in burns or
5. Tighten plug (1).
injuries.
6. Supply oil through the hole for plug (3) until
¡ The pressure in the travel motor
oil flows out of the hole of plug (2).
reduction gears case may cause oil or
7. Tighten plugs (2) and (3).
the plug to fly out. Loosen the plug
slowly to release the pressure.
IMPORTANT: If the percentage of the

traveling time within the total operating
time is high, replace the gear oil earlier
than the specified time.
119
MAINTENANCE
Every 250 Hours
Replacing the Engine Oil and Oil 1. Open the left side cover.
Filter
Refer to page 113 “Replacing the Engine Oil 4 3
and Oil Filter”.
1
Inspecting and Adjusting the Fan 2
Belt 5
L3G016
Refer to page 114 “Inspecting and Adjusting
the Fan Belt”. 2. Loosen the clamps (1) and remove the
dust cup (2).
3. Clean the inside of the dust cup (2).
Cleaning the Air Cleaner 4. Remove the outer element (3).
Do not remove and clean the inner
element (5).
WARNING
5. Clean the inside of the body (4).
maintenance.
• The engine, muffler, radiator and
many other parts of the machine are
hot directly after the engine is
stopped. Touching these parts will
cause burns.
¡ Wear required appropriate equipment E4G033
such as safety glasses and filter mask
when using compressed air, as metal 6. Clean the outer element (3) with dried
fragments or other objects can fly and compressed air {294 to 490 kPa (43 to 71
cause serious personal injury. psi)}.
First blow the air from the inside of the
IMPORTANT: Be careful not to scratch element along the flutes, then blow the air
the element. Do not use an element if it is from the outside, and finally from the inside
damaged. again.
IMPORTANT: When operating the
machine in very dusty places, inspection
and maintenance should be performed
every day.
120
MAINTENANCE
Every 250 Hours
Cleaning the Radiator Fins and

Oil Cooler Fins
WARNING
Wear required appropriate equipment
such as safety glasses and filter mask
E4G034 when using compressed air, as metal
7. Light up the inside of the outer element fragments or other objects can fly and
(3) with a bulb, inspect it, and replace it if cause serious personal injury.
there are small holes or thin spots.
8. Install the outer element (3). IMPORTANT: Be careful not to damage
9. Install the dust cup (2) with the “TOP” mark the radiator fins and oil cooler fins when
at the top, then fasten it with the clamps cleaning them.
(1). ¡ When using compressed air or
pressurized water, make sure the
pressure is no higher than 200kPa (28
psi) and hold the nozzle sufficiently
away from the fins.
IMPORTANT: When using water, cover
the electrical system to prevent water
from getting in.
IMPORTANT: When operating the
machine in very dusty places, inspection
and maintenance should be performed
every day.
L3G017
1. Open the left side cover and the engine

hood.
2. Blow compressed air on the radiator fins
and oil cooler fins to remove mud and dirt
stuck on them.
121
MAINTENANCE
Every 500 Hours
Replacing the Hydraulic Oil Replacing the Fuel Filter

Return Filter
Refer to page 112 “Replacing the Hydraulic WARNING
Oil Return Filter”. ¡ Do not smoke or permit open flames
fuel system.
1
L3G031
1. Open the right side cover.

2. Using a filter wrench, turn the filter (1)
counterclockwise and remove it.
stand.
the new filter.
6. Tighten 2/3 more turn with the filter wrench
after the filter packing comes in contact
with the surface of installation.
7. Bleed the air.
Refer to page 145 “Bleeding the Air from
the Fuel System”.
122
MAINTENANCE
Every 500 Hours
Replacing the Water Separator

Filter
WARNING
fuel system.
3
2
1
L3G032
1. Open the right side cover.

2. Place a pan under the drain hose.
3. Open the drain cock (1) and drain the fuel.
4. Remove the sensor (2).
5. Remove and discard the filter (3).
6. Install the sensor (2) on the new filter.
stand.
the new filter.
10. Tighten 2/3 more turn with the filter
wrench after the filter packing comes in
contact with the surface of installation.
11. Bleed the air.
Refer to page 145 “Bleeding the Air from
the Fuel System”.
123
MAINTENANCE
Every 1000 Hours
Cleaning the Engine Cooling 1. Open the left side cover and the engine
hood.
System
WARNING 3 2
to cool down before performing FULL
maintenance. LOW
H
• The engine, muffler, radiator and L
many other parts of the machine are
hot directly after the engine is L3G004
stopped. Touching these parts will
cause burns. 2. Gradually loosen the radiator cap (3) to
• The engine coolant is also hot and release the internal pressure, then
under high pressure. Be careful remove.
when loosening caps and plugs.
Working on the machine under these
conditions could result in burns or
injuries due to the hot coolant 4
spurting out.
¡ If maintenance must be performed with
the engine running, always work as a
two person team with one person
sitting in the operator’s seat while the L3G020
other works on the machine.
• When performing maintenance, be 3. Place a pan for catching the spent coolant
sure to keep your body and clothing under the drain plug (4), then loosen the
away from moving parts. drain plug (4) and drain the coolant.
¡ Standing at the back of the machine 4. Tighten the drain plug (4).
while the engine is running is extremely 5. Add tap water through the radiator’s
dangerous, as the machine could move coolant supply port up to the top of the
suddenly. Never stand at the back of port. Take your time doing this, adding the
the machine while the engine is water slowly to avoid any air from entering
running. the radiator.
¡ Do not remove the radiator cap or drain 6. Close the radiator cap (3).
plugs when the coolant is hot. Stop the 7. Start the engine and run it at a speed
engine, let the engine and radiator cool slightly above low idling. Raise the water
and loosen the radiator cap or drain temperature to at least 90°C, then run the
plugs slowly. engine for about 10 minutes with the
thermostat open.
When cleaning, if the temperature of the 8. Stop the engine, let the water’s
coolant is low, the thermostat will be closed temperature lower, then loosen the drain
and the coolant will not circulate in the plug (4) and drain the water.
radiator. Heat the coolant water to at least
90°C before cleaning.
124
MAINTENANCE
Every 1000 Hours
9. After draining the water, clean using Replacing the Air Cleaner
cleaning agent. Clean following the
Elements
instructions included with the cleaning
agent you are using.
WARNING
10. Repeat steps 4 to 8 to rinse the cooling
system. Stop the engine and allow the machine
11. Tighten the drain plug (4). to cool down before performing
12. Slowly add the new coolant (mixture of maintenance.
antifreeze and tap water) through the ¡ The engine, muffler, radiator and many
radiator’s coolant supply port up to the other parts of the machine are hot
top of the port. Take your time doing this. directly after the engine is stopped.
13. Close the radiator cap (3). Touching these parts will cause burns.
14. Warm up the engine. Use the meters to
check that there are no irregularities in IMPORTANT: Do not use an element if its
the cooling system at this time. flutes, gaskets or seals are damaged.
15. Raise the water temperature to at least
90°C, then run the engine as such for 1. Open the left side cover.
about 10 minutes.
16. Stop the engine, let the water’s
temperature lower, then check the level 4 3
of coolant in the radiator, and replenish
up to the top of the coolant supply port.
17. Close the radiator cap (3).
18. Clean the interior of the reserve tank (1), 1
2
then add coolant to the upper limit (H). 5
19. After replacing the coolant, inspect the
L3G016
coolant level once again after operating
the machine. 2. Loosen the clamps (1) and remove the
The coolant permeates the entire system dust cup (2).
during operation, so the level decreases. 3. Clean the inside of the dust cup (2).
Replenish by the amount the level has 4. Remove the outer element (3).
decreased. Do not yet remove inner element (5).
5. Clean the inside of the body (4).
6. Remove the inner element (5).
7. Install the new elements.
8. Install the dust cup (2) with the “TOP” mark
at the top, then fasten it with the clamps
(1).
125
MAINTENANCE
Every 1000 Hours
Replacing the Travel Motor Gear Inspecting and Adjusting the

Oil Engine Valve Clearance
Refer to page 119 “Replacing the Travel This operation requires experience. Have it
Motor Gear Oil”. performed by a Takeuchi sales or service
outlet.
Replacing the Air Breather Filter

Retightening the Engine Cylinder
WARNING Head Bolts
This operation requires experience. Have it
steps and handrails when climbing on outlet.
Inspecting the Engine Fuel
¡ Oil may spurt out if caps or filters are
removed or pipes disconnected before Injection Pressure and Spray
releasing the pressure in the hydraulic Condition
system. This operation requires experience. Have it
• Gradually press the air breather performed by a Takeuchi sales or service
button to relieve tank pressure. outlet.
N A
W
T
G
B
W
H L2G023
1. Remove cap nut (N) on the air breather.

2. Press botton (T) and bleed the air from
the tank.
3. Remove seal washers (W) and nut (G).
4. Remove cover (H).
5. Replace filter (A), making sure it is in the
proper direction.
6. Line up the cut section of body (B) and
cover (H) and install.
7. Install seal washers (W) and nut (G).
8. Tighten securely by hand with cap nut (N).
126
MAINTENANCE
Every 2000 Hours
Replacing the Hydraulic Oil and 4 2

Cleaning the Suction Strainer
10
5 3
WARNING 8
1
maintenance.
• The engine, hydraulic lines and many
other parts of the machine are hot 6
directly after the engine is stopped.
Touching these parts will cause
burns.
• The hydraulic fluid is also hot and
under high pressure. 7
Be careful when loosening caps and L3G008
plugs. Working on the machine under

2. Remove cap nut (2).
these conditions could result in
3. Press button (3) and release the pressure
burns or injuries due to the hot oil
in the tank.
spurting out.
4. Replace the air breather filter (A).
Refer to page 126 “Replacing the Air
Breather filter”.
6. Loosen the bolts, and remove the flange (4).
7. Remove the return filter (5).
¡ Oil may spurt out if caps or filters are
removed or pipes disconnected before
under the drain plug (7).
releasing the pressure in the hydraulic
9. Loosen the drain plug (7) and drain the
system.
hydraulic oil.
• Gradually press the air breather
10. Loosen the bolts, and remove the flange
button to relieve tank pressure.
(8).
• When removing plugs or screws or
11. Remove the suction strainer (9) and
disconnecting hoses, stand to the
clean it.
side and loosen slowly to gradually
12. Clean the inside of the hydraulic tank.
release the internal pressure before
13. Install the new return filter and suction
removing.
strainer (9).
14. Install the flanges (4) and (8).
1. Slew 45° clockwise and set the machine
15. Tighten the drain plug (7).
to the hydraulic oil level inspection posture.
16. Supply hydraulic oil up to the middle of
Refer to page 109 “Inspecting the
the sight gauge (6) from the hole of plug
Hydraulic Oil Level and Replenishing”.
(10).
17. Tighten the plug (10).
127
MAINTENANCE
Every 2000 Hours
18. Follow the procedure next “Bleeding the ¡ Slew motor

air” to bleed the air from the hydraulic oil
circuit.
19. Set the machine to the hydraulic oil level
inspection posture and inspect the level
once the temperature of the oil has
dropped.
Refer to page 109 “Inspecting the
Hydraulic Oil Level and Replenishing”.
2
Bleeding the air

1
IMPORTANT: After replacing the
hydraulic oil, bleed the air from the
hydraulic circuit and hydraulic devices.
Failure to do so may damage the
L3G0261
hydraulic devices.
1. Loosen the bolts and remove the center
¡ Hydraulic pump cover (1).
1 2 3. Once hydraulic oil overflows from the plug
hole, tighten the plug (2).
4. Install the center cover (1).
¡ Cylinders
1. Start the engine and run it at low idle for
10 minutes.
L3G021
2. Set the engine to a low idle, then extend
1. Open the engine hood. and contract all the cylinders 4 or 5 times,
2. Disconnect the drain hose (1) from the without going to the stroke end.
hydraulic pump. 3. Run the engine at high speed, then extend
3. Once hydraulic oil overflows from the and contract all the cylinders 4 or 5 times,
elbow (2), connect the drain hose (1). without going to the stroke end.
4. Set the engine back to a low idle, then
extend and contract all the cylinders 4 or
5 times to the stroke ends.
128
MAINTENANCE
Every 2000 Hours

Injection Timing
outlet.

Injection Valve
outlet.
129
MAINTENANCE
When Required
Replacing the Bucket Teeth and 3. Remove the key, then check that the
bucket is stable.
the Side Cutters
Replace the bucket teeth and the side cutters
when the tooth points or the side cutters are 3
worn, before the adapter or the bucket is
damaged.
WARNING
2
¡ Before performing maintenance or 1 4 E4G043
repairs under the machine, set all
working equipment against the ground 4. Remove locking pin (1) and remove point
or in the lowermost position. (2).
¡ To prevent unexpected movement, 5. Take out rubber pin lock (3) and check
securely block the working elements whether it is still usable.
when repairing or replacing the bucket
teeth and the side cutters.
E
¡ Wear required appropriate equipment
such as safety glasses when using
hammers, as metal fragments or other
objects can fly and cause serious
personal injury. F
¡ Do not allow unauthorized personnel
in the work area.
E4G044
¡ Bucket tooth E ....... When these are cracks in the rubber

Removal and it seems like the roller is about
1. Clean the bucket and park the machine in to come off.
a flat, safe place where the ground is hard. F ....... When the roller becomes dented
when pressed with a finger.
E4G042
2. Set the bottom surface of the bucket flat

and lower it on a block so that the locking
pin can be knocked out.
130
MAINTENANCE
When Required
Installation ¡ Side cutter

Installation
4
3
E4G045
G4G026
1. Push rubber pin lock (3) into welding
adaptor (4). 1. Insert the bolts from the inner of the bucket
and tighten the nuts.
Do not let the rubber pin lock stick out past Tightening torque: 241 N·m (178 ft-lb)
the welding adapter surface. 2. Caulk the bolts with a punch at three spots
along the periphery of the screw to prevent
the nuts from coming loose.
Improper Proper 4 Proper
2
E4G046
2. Install point (2) onto welding adaptor (4).

• Insert the point so that the surface
behind the point’s pin hole is flush or
deeper than the surface behind the
welding adapter’s pin hole.
E4G047
3. Drive in locking pin (1).
After driving in the locking pin, use a pin with

the same surface as the point surface. Do
not use worn locking pins.
131
MAINTENANCE
When Required
Adjusting the Gap Between the

Bucket and Arm
WARNING
¡ Before performing maintenance or 4
repairs under the machine, set all 3
working equipment against the ground 2 E4G050
or in the lowermost position.

4. Remove the three bolts (2), the end plate
¡ To prevent unexpected movement,
(3) and flange (4).
securely block the working equipment
when adjusting.
1
5
A
5
4
3
2 E4G051
E4G048 5. Extract adjustment shim (5) from between

flange (4) and the bucket body according
1. Ground the bucket as shown on the
to gap (A).
diagram above in a stable position.
Adjustment shim thickness : 0.5 mm (0.02
2. Check that the bucket dose not move, then
in.)
set the safety lock lever to the locked
Be careful that the gap is no less than 0.5
position and stop the engine.
mm (0.02 in.) after adjustment.
Supplement
1 A Example (for a gap of 2 mm or 0.08 in.):
2 mm – 0.5 mm (standard value)
= 1.5 mm (0.06 in)
In the above example, three shims (5) should
be removed.
6. Insert adjustment shim (5) removed in step

E4G049 5 above between end plate (3) and flange
(4) and fasten it in place with the three
3. Slide the O-ring (1) to bring the gap (A)
bolts (2).
into view and measure the width of the
• Tightening torque for bolts (2)
gap (A).
54.9 N·m (40.5 ft-lb.)
The gap (A) should be 0.5 mm (0.02 in.)
Swing the buckte slightly to the left and
7. Return the O-ring (1) to their original
lightly press the arm point to the left side
position.
of the bucket (the side without an adjuster).
132
MAINTENANCE
When Required
Inspecting and Replenishing the Draining the Water Separator

Windshield Washer Fluid
Use a windshield washer fluid designed WARNING
specifically for motor vehicles. Follow the ¡ Do not smoke or permit open flames
instructions including with the washer fluid. while handling fuel or working on the
fuel system.
2 place and allow it to cool down before
1
G4G030
3
Inspection
1. Open the cab door. 2
2. Inspect the washer tank (1) and add 1
washer fluid if the level is low.
L3G032
Replenishment 1. Open the right side cover.

1. Mix the washer fluid to the prescribed 2. Place a pan under the drain hose.
concentration. 3. Open the drain cock (1) and drain the
2. Remove the cap (2) and add washer fluid. water.
3. Reinstall the cap (2). 4. Close the drain cock (1).
Bleeding the air from the fuel system

Refer to page 145 “Bleeding the Air from the
Fuel System”.
Supplement: Air in the fuel system can
make it difficult to start the engine and cause
engine problems. Also bleed the air when
the fuel tank is emptied.
133
MAINTENANCE
When Required
2. Set the safety lock lever to the locked

Replacing the Bucket
position and stop the engine.
WARNING
¡ Before performing maintenance or
repairs under the machine, set all
working equipment against the ground
or in the lowermost position. 5
¡ If maintenance must be performed with 2
the engine running, always work as a 4 3 1
two person team with one person E4G052
sitting in the operator’s seat while the

other works on the machine. 3. Remove the bolt (1).
• When performing maintenance, be 4. Hammer pin (2) out of the bucket.
sure to keep your body and clothing 5. Remove the bucket.
away from moving parts. Inspect the pin seal (3) and replace it if it
¡ Wear required appropriate equipment is deformed or damaged. (See next
such as safety glasses and filter mask page.)
when using hammers, as metal
fragments or other objects can fly and Installation
cause serious personal injury.
4
¡ When lining up the pin holes, always
do so by sight. Your finger may be cut
off if you stick it into the hole.
Removal
E4G053
1. Set the bucket’s O-ring (4) as shown on

the diagram.
5
E4G048
1. Ground the bucket as shown on the 6

diagram above in a stable position. A B
Supplement: When removing pins, set the
bucket so that it is just gently against the
ground. If it is strongly against the ground, E4G054
the resistance will be great and it will be

difficult to remove the pin. 2. Line up pin hole (A) in the bucket with the
pin hole in the arm (5), and install the pin
(2).
134
MAINTENANCE
When Required
3. Operate the cylinder, line up pin hole (B) Replacing the pin seal
in the bucket with the pin hole in the link
arm (6), and install the pin (2).
3 E4G057
1. Set the pin seal (3) in the direction shown

0.5~1mm on the diagram above.
E4G055
2. Use a mallet to slowly press the pin seal
4. Line up the turn prevention holes, install in. Be careful not to damage the seal.
the bolt (1), and the nuts.
Be sure to leave a gap of about 0.5 ~ 1
mm (0.02 ~ 0.04 in.) between the nut and
bucket bush, or the nut will come loose.
E4G056
5. Adjust the gap between the bucket and

the arm. Refer to page 132.
6. Slide the O-ring (4).
135
MAINTENANCE
When Required
Boom swing pedal

Lubricating the Levers
WARNING
Set the machine to the parking posture,
stop the engine, remove the starter key
and store it. Failure to do so may result
in the machine moving abruptly, leading
to serious injury or death.
If the levers or pedals no longer move 1. Remove the lower mount section of the
smoothly, supply grease. boot (1) and turn it upwards.
2. Wipe off the old grease.
Operating levers 3. Supply grease to points (A) and (B).
4. Set the boot (1) back as it was.
A 1
E4G058
1. Remove the lower mount section of the

boot (1) and turn it upwards.
3. Supply grease to points (A) and (B).
Travel levers
B A B
1 L3G022
1. Remove the lower mount section of the

boot (1) and turn it upwards.
3. Supply grease to points (A) and (B).
136
MAINTENANCE
When Required
(3) Metal core

Inspecting the Rubber Crawlers
Repair or replace the rubber crawlers if their
conditions are as described below. Consult
a Takeuchi sales or service outlet about
repairs or replacement.
Rubber crawler
Replace the crawler if the entire crawler is 3 E4G064
stretched and cannot be adjusted.
Replace if even one metal core is off.
(1) Lug
(4) Rubber
4 3 60 mm or greater
A
1 2 E4G062
E4G065
Replace if the height of (A) is 5 mm (0.2 in.)
or below. Repair if there are cracks of 60 mm (2.4 in.)
or greater in length.
(2) Steel cord If the steel cord is visible, repair as soon as
possible, regardless of the length of the
crack.
2
E4G063
Replace if the steel cord is exposed over 2

or more links.
Replace if half or more of the steel cords on
one side are cut.
137
MAINTENANCE
When Required
Removal
Replacing the Rubber Crawlers
WARNING
¡ If you must work beneath the raised
machine or equipment, always use
wood blocks, jack-stands or other rigid
and stable supports. Never get under
the machine or working equipment if
they are not sufficiently supported.
This procedure is especially important 1. Start the engine and raise the machine
when working on hydraulic cylinders. body with the hoe attachment and dozer
¡ If maintenance must be performed with blade.
the engine running, always work as a 2. Stop the engine.
two person team with one person
sitting in the operator’s seat while the
other works on the machine.
• When performing maintenance, be
sure to keep your body and clothing
away from moving parts.
This machine uses a hydraulic cylinder to

adjust the tension of the crawler belts. Note
that it is not necessary to regularly perform
adjustments of the tension of the belt itself. 3. Remove the valve covers (1) at the center
of the left and right crawler frames.
IMPORTANT: During the replacement
procedure, only start the engine when
raising and lowering the machine body.
Otherwise, always keep the engine off.
IMPORTANT: When the travel speed
switch is set to the 2nd speed side while
the engine is running, the tensioning
cylinder rods extend and the crawlers are
tightened.
4. Loosen the lock plate (2) counterclockwise.
5. Turn the valve handle (3) counterclockwise
to loosen the tension of the crawler.
6. Once the crawler is completely loose,
tighten the valve handle (3).
7. Tighten the lock plate (2).
8. Do the same for the other side.
138
MAINTENANCE
When Required
Installation
1. Engage the crawlers with the left and right
sprockets.
2. Set the left and right crawlers on the idlers.
3. Start the engine.
4. Press the travel speed switch once and
set it to the 2nd speed side. The left and
right crawlers are tightened
simultaneously.
9. Slowly lower the dozer blade side of the
machine body, by the dozer blade lever.
(Do not start the engine.)
10. Ground the crawlers and lower the
machine body so that the crawler slack
is maximum.
11. When the crawlers come away from the
idlers, slide the crawlers to the outside
and remove them.
12. Disengage the crawlers and sprockets,
then remove the crawlers from the 5. Check that the crawlers are properly
crawler frames. tightened. Standard value (A).
Refer to page 115 “Inspecting the Crawler
Tension”.
139
MAINTENANCE
Long-term Storage
Procedures for storage During storage

If the machine is to be stored for 30 days or
more, store it indoors. If it must be stored WARNING
outdoors, stop it on wood laid out on a flat
surface and place a waterproof cover over it ¡ Do not operate the engine in an
so that it stays dry. enclosed area without adequate
1. Clean the machine. ventilation.
2. Inspect for oil leakage, water leakage and ¡ If natural ventilation is poor, install
loose nuts and bolts. ventilators, fans, exhaust extension
3. Add fuel and replace the hydraulic oil and pipes or other artificial venting devices.
oil.
4. To prevent rusting and freezing, replace 1. To prevent rusting, operate the machine
the engine coolant with long-life coolant once a month so that the oil is fully
(LLC). circulated.
Refer to page 124 “Cleaning the Engine 2. Inspect the battery and recharge it if
Cooling System”. necessary.
5. Use the grease gun to supply grease to Have the battery charged by a Takeuchi
the grease nipples. sales or service outlet.
6. Fully contract the bucket and arm cylinders
and ground the bucket and dozer blade. Starting the machine after storage
7. Apply rust-prevention oil to the hydraulic
cylinder rods. IMPORTANT: If the “Procedures for
8. Disconnect the cable from the battery’s storage” have not been performed and
“–” terminal and cover the battery to the machine has been stored for a long
prevent freezing. period of time, consult a Takeuchi sales
or service outlet before reusing the
machine.
1. Wipe off the rust-prevention oil that was

applied to the hydraulic oil cylinders’ piston
rods.
2. Add fuel, oil and grease to all parts.
140
TROUBLESHOOTING
Symptoms that are not Malfunctions ...... 142
If the Engine Overheats ........................... 143
If the Battery Goes Dead .......................... 144
After the Fuel Runs Out ........................... 145
If a Fuse Blows ......................................... 146
If a Warning Lamp Flashes ...................... 148
Other Symptoms ...................................... 150
To Lower the Boom .................................. 152
Towing ...................................................... 153
141
TROUBLESHOOTING
Symptoms that are not Malfunctions
The following symptoms are not ¡ When the bucket is operated while making
malfunctions: a right pivot turn (i.e., when only the left
crawler is turning), the speed of the pivot
turn may suddenly increase.
¡ Performance decreases when an

attachment weighing more than a
standard arm or bucket is mounted.
E4J001
¡ When the arm reaches the vertical position

while contracting it while the engine is
running at low speed, the contracting
speed slows down momentarily.
E4J002
¡ When the bucket teeth reach the

horizontal position while the engine is
running at low speed, the speed of bucket
movement slows down momentarily.
¡ The slew motor produces noise at the

beginning and end of the slewing
operation.
¡ The travel motor produces noise when

stopped suddenly during high speed
travel.
¡ The control valve produces noise if

excessive force is applied to the working
equipment and when the stroke end is
reached.
142
TROUBLESHOOTING
If the Engine Overheats
Procedure
WARNING
1. Park the machine in a safe place.
¡ Do not open the engine hood when 2. Inspect whether the engine oil pressure/
there is steam coming from the engine coolant level warning lamp is flashing or if
room. The steam or hot water may there is steam coming out when the
spurt out, resulting in burns. engine hood is closed.
¡ Do not remove the radiator cap or drain 3. If there is steam, stop the engine
plugs when the coolant is hot. Stop the immediately and contact a Takeuchi sales
engine, let the engine and radiator cool or service outlet for repairs.
and loosen the radiator cap or drain If the engine oil pressure/coolant level
plugs slowly. warning lamp is off, run the engine at low
¡ Stop the engine and allow the machine idle and let the water temperature
to cool down before performing decrease.
inspection and maintenance. 4. Once the water temperature gauge drops
to the green zone, stop the engine.
The following symptoms indicate 5. Once the engine is cool, perform the
overheating: following inspections and procedures:
¡ Fan belt slack ......................... Adjust.
Refer to page 114.
¡ Coolant level .............................. Add.
Refer to page 107.
¡ Water leakage ........................ Repair.
¡ Radiator fins ............................ Clean.
Refer to page 121.
¡ Sediment in cooling system ..... Clean.
Refer to page 124.
L3J001 If the problem persists after the above
¡ An alarm is sounded and the coolant procedures are taken, contact a Takeuchi
temperature warning lamp, engine sales or service outlet for repairs.
emergency lamp flashes.
When the engine oil pressure/coolant level
warning lamp is flashing simultaneously,
the coolant level is low.
¡ The water temperature gauge is in the red
zone.
¡ The engine slows down and the force
decreases.
¡ Steam comes from the engine room.
143
TROUBLESHOOTING
If the Battery Goes Dead
The following symptoms indicate that the Connecting the jumper cables
battery is dead:
¡ The starter motor does not turn or turns IMPORTANT: Set the starter keys of both
weakly, and the engine does not start. the rescue vehicle and problem vehicle
¡ The horn is weak. to the OFF position.
Procedure Rescue vehicle battery Problem vehicle battery

Use jumper cables and start the engine using
2 1
the rescue vehicle’s battery. R
WARNING
¡ Use jumper cables only in the 3 To engine block
B
recommended manner. Improper use 4
E4J005
of jumper cables can result in battery
explosion or unexpected machine 1. Connect the clip of jumper cable (R) to
motion. the problem vehicle’s “+” terminal.
• Do not let the problem vehicle and 2. Connect the other clip of jumper cable (R)
rescue vehicle touch each other. to the rescue vehicle’s “+” terminal.
• Do not let the “+” and “–” clips of the 3. Connect the clip of jumper cable (B) to
jumper cables touch each other. the rescue vehicle’s “–” terminal.
• Connect the jumper cables to the “+” 4. Connect the other clip of jumper cable (B)
terminals first, and disconnect them to the problem vehicle’s engine block.
from the “–” terminals (ground) first. Connect the clip as far from the battery as
• Connect the final clip of the jumper possible.
cable to a point as far away from the
battery as possible. Starting the engine
¡ Use safety glasses when using jumper 1. Check that the clips are securely
cables to start the machine. connected to the terminals.
2. Start the rescue vehicle’s engine and run
IMPORTANT: Use jumper cables and it at high speed.
clips of a size suited to the battery’s 3. Start the problem vehicle’s engine.
capacity. Do not used damaged or
corroded jumper cables and clips.
IMPORTANT: The rescue vehicle’s
battery must have the same capacity as
the problem vehicle’s battery.
IMPORTANT: Connect the clips securely.
144
TROUBLESHOOTING TROUBLESHOOTING
If the Battery Goes Dead After the Fuel Runs Out
Disconnecting the jumper cables Bleeding the Air from the Fuel
Once the engine starts, disconnect the
System
jumper cables following the connection
procedure in reverse order. 1. Supply fuel.
Rescue vehicle battery Problem vehicle battery

3 4 OFF
R ON
START
2 From engine block

B
1
E4J006
L3D001
1. Disconnect the clip of jumper cable (B) 2. Turn the starter key to the ON position and
from the problem vehicle’s engine block. hold it there for about 20 seconds.
2. Disconnect the other clip of jumper cable The automatic air bleeder bleeds the air
(B) from the rescue vehicle’s “–” terminal. from the fuel system.
3. Disconnect the clip of jumper cable (R)
from the rescue vehicle’s “+” terminal. Supplement: Air in the fuel system can
4. Disconnect the other clip of jumper cable make it difficult to start the engine and cause
(R) from the problem vehicle’s “+” terminal. engine problems. Also bleed the air when
the fuel tank is emptied or air in the fuel
Recharging system.
Have a Takeuchi sales or service outlet
recharge batteries that have gone dead.
145
TROUBLESHOOTING
If a Fuse Blows
If a light does not turn on or the electric Fuse Layout and Circuits Protected
system does not operate, a fuse may be
Capacity Protected circuit Capacity Protected circuit
blown. Inspect the fuses.
15A Horn, 3A Throttle controller
Inspecting and Replacing the Interior Light (B)
10A Proportional control 1A Stop solenoid hold
Fuse
solenoid
20A Lights 10A External power socket
WARNING
If the fuse blows as soon as it is replaced, 20A Wiper 10A Cigarette lighter
there is a problem with the electric
system. Continued use may lead to fire. 5A Radio 10A Lever lock
Consult a Takeuchi sales or service
outlet. 5A Heater 10A Automatic-glow
1. Turn the starter key to the OFF position 30A Air conditioner 20A Throttle controller
and stop the engine. (option) (ACC)
20A Instrument cluster, 20A Feed pump,
Lift alarm (option) Stop solenoid timer
10
10
20
10
10
20
10
20
10
5
10
5
20
20
10
20
1
L3J002
2. Open the fuse box cover (1).

3. Inspect for any blown fuses.
Blown Normal
E4J007
4. If a fuse is blown, replace it with a spare

fuse of the same capacity.
146
TROUBLESHOOTING
If a Fuse Blows
Inspecting the Fusible Link
L3J0031
If the power is not switched on after turning

the starter switch to the ON position, the
cartridge type fusible links (1) might be blown
open. Open the left side cover and inspect.
If the fusible link is blown, please contact your
dealer.
Supplement: A fusible link is a large piece
of fuse wiring which is mounted in a circuit
which carries a large electrical current. Link
a regular fuse, the fusible link protects the
electrical parts and wiring from damage due
to abnormally large currents.
147
TROUBLESHOOTING
If a Warning Lamp Flashes
If an alarm is sounded or a warning lamp starts flashing during operation, park the machine
in a safe place and perform the procedures described below.
Warning lamp Lamp name Procedure
Engine A problem has occurred in the engine lubrication system

emergency or cooling system.
lamp ¡ When there is a problem in the engine lubrication
system or coolant level, the engine oil pressure/coolant
level warning lamp flashes simultaneously.
¡ When the coolant water temperature has risen
G4B009 irregularly, the coolant temperature warning lamp
flashes simultaneously.
For the procedures, refer to the respective warning
lamps below.
Engine oil Inspect the engine oil level or coolant level. If the lamp
pressure/ is flashing even though the level is normal or if it
coolant level continues flashing after oil or coolant are supplied,
warning lamp consult a Takeuchi sales or service outlet.
L3J004 Refer to page 107 or 108 “Inspecting and replenishing
the coolant” or “Inspecting and Replenishing the
Engine Oil”.
Coolant The coolant temperature has risen irregularly and the

temperature engine is overheating.
warning lamp Refer to page 143 “If the Engine Overheats”.
C
C4B012
Battery charge There is a problem with the fan belt or charger.

warning lamp Inspect the fan belt for slack or breakage and adjust as
necessary. If the lamp continues flashing after
maintenance, there is a problem with the charger.
Consult a Takeuchi sales or service outlet.
OSOB080 Refer to page 114 “Inspecting and Adjusting the Fan
Belt”.
Air cleaner The air cleaner filter is clogged.

warning lamp Refer to page 120 “Cleaning the Air Cleaner”.
G4B010
148
TROUBLESHOOTING
If a Warning Lamp Flashes
Warning lamp Lamp name Procedure
Water Water has accumulated in the water separator. Drain

separator the water.
warning lamp Refer to page 133 “Draining the Water Separator”.
L3J005
Fuel level The fuel level is low. Supply fuel.

warning lamp Refer to page 42 “Fuel Filler Cap”.
L3J006
149
TROUBLESHOOTING
Other Symptoms
For symptoms not included on the table below or if the problem persists after the proper
procedures have been taken, consult a Takeuchi sales or service outlet.
Symptom Main cause Procedure

Left and right operating ¡ Insufficient grease on left ¡ Supply grease.
levers do not move and right operating levers Refer to page 136.
smoothly
Travel levers and boom ¡ Insufficient grease on travel ¡ Supply grease.
swing pedal do not levers and boom swing Refer to page 136.
move smoothly pedal
Hoe attachment, ¡ Safety lock lever is raised ¡Lower the safety lock lever.
auxiliary hydraulics, Refer to page 53.
slewing or traveling ¡ Fuse is blown ¡ Replace the fuse.
operation not possible Refer to page 146.
Digging force is ¡Insufficient hydraulic oil level ¡ Replenish to the prescribed
insufficient level.
Refer to page 109.
¡Hydraulic oil is not heated ¡ Perform the warm-up
procedure.
Refer to page 70.
¡Air cleaner is clogged ¡ Clean the air cleaner.
Refer to page 120.
¡Hydraulic oil is not of ¡ Replace the hydraulic oil.
suitable type Refer to page 127.
Traveling is not possible ¡Stones or foreign objects ¡ Remove the foreign object.
or not smooth are stuck
Machine does not travel ¡ Stones or foreign objects ¡ Remove the foreign object.
straight forward are stuck
Slew speed cannot be ¡ Fuse is blown ¡ Replace the fuse.
shifted Refer to page 146.
Travel speed cannot be ¡ Fuse is blown ¡ Replace the fuse.
changed Refer to page 146.
150
TROUBLESHOOTING
Other Symptoms
Symptom Main cause Procedure

Slewing is not possible ¡Insufficient grease on slew ¡ Supply grease.
or not smooth bearing Refer to page 116.
Hydraulic oil ¡ Insufficient hydraulic oil ¡ Replenish to the prescribed
temperature is too high level.
Refer to page 109.
Starter motor turns but ¡Insufficient fuel ¡ Supply fuel.
engine does not start Refer to page 109.
¡Air in fuel system ¡ Bleed the air.
Refer to page 145.
¡Water in fuel system ¡ Drain the water.
Refer to page 133.
Crawlers slip off ¡ Crawlers are too loose ¡ Increase the tension.
Tensioning cylinder valve Refer to page 138.
are too loose
Engine exhaust is white ¡ Excessive engine oil ¡ Adjust to the prescribed
or bluish level.
Refer to page 108.
¡ Poor fuel ¡ Replace the fuel.
Engine exhaust is ¡ Air cleaner is clogged ¡ Clean the air cleaner.
occasionally black Refer to page 120.
Irregular noise is ¡ Low quality fuel is being ¡ Replace the fuel.
produced from the used ¡ If the Engine Overheats
engine (combustion or ¡ Engine is overheating Refer to page 143.
mechanical noise) ¡ Replace the muffler.
¡ Damage in muffler (Request at a sales or
service outlet.)
151
TROUBLESHOOTING
To Lower the Boom
If the hoe attachment must be lowered to 1. Loosen the bolts and remove cover (1).
the ground while the engine is stopped, use
the following procedure to do so.
This operation is dangerous and requires 3
experience. Have it performed by a Takeuchi
sales or service outlet. M 4
When equipped with accumulator (option):

2
Refer to page 199 “Accumulator”.
Procedure J1J004
2. Put mark (M) on the plug of the port relief

WARNING
valve (2) and set screw (3).
¡ Never jump off the machine. Use the 3. Gripping the set screw (3) with a
steps and handrails when climbing on hexagonal wrench so that it does not turn
and off the machine, and always together with the lock nut (4), loosen the
support your body at three points with lock nut (4).
your hands and feet. 4. Turn the set screw (3) slowly one turn to
¡ Do not approach in the area of the lower the boom.
ground where the hoe attachment is to 5. Check for safety and machine stability.
be lowered. You may be hit by dirt 6. Turn the set screw (3) back to its original
falling out of the bucket or the hoe position.
attachment as it drops. 7. Gripping the set screw (3) with a
¡ Turn the port relief valve’s set screw hexagonal wrench so that it does not turn
slowly so that the boom lowers slowly. together with the lock nut (4), tighten the
Do not turn the screw more than the lock nut (4).
specified amount.
Tightening torque:
27 to 31 N·m (20 to 23 ft-lb.)
8. Reinstall the cover (1).
L3J007
152
TROUBLESHOOTING
Towing
Using the light load towing hole

WARNING
When towing, selecting the wrong wire IMPORTANT: Be sure to follow all the
rope, inspecting improperly, or towing in steps below closely when using the light
the wrong way could lead to accidents load towing hole to tow. Failure to heed
resulting in serious injury or death. even one of the steps may cause damage
¡ The wire rope breaking or coming to the light load towing hole or other parts
detached could be extremely of the frame.
dangerous. Use a wire rope suited for
the required towing force.
¡ Do not use a wire rope that is kinked, 2 1
twisted or otherwise damaged.
¡ Do not apply strong loads abruptly to
the wire rope.
¡ Use safety gloves when handling the
wire rope.
¡ Make sure there is an operator on the N0J003
machine being towed as well as on the
machine that is towing. ¡ Maximum pulling force:
¡ Never tow on slopes. 43200 N (9700 lb) or less
¡ Do not let anyone near the wire rope
while towing. 1. Attach the wire rope to the shackle (1).
2. Fasten the shackle (1) to the light load
Towing the Machine towing hole (2).
Use the procedure described below to tow 3. Attach the wire rope to the object to be
heavy objects or the machine itself if it should towed.
get stuck in the mud and not be able to get 4. Make the wire rope horizontal and line up
out on its own. straight with the travel frame.
5. Move the machine to tauten the wire rope.
6. Move the machine slowly and tow.
N0A006
1. Fasten the wire rope to the frame.

2. Place splints or other objects between the
wire rope and frame to prevent the
machine and wire rope from getting
damaged.
3. Move the machine to tauten the wire rope.
4. Move the machine slowly and tow.
153
154
SPECIFICATIONS
Main Specifications ................................. 156
Machine Dimensions ............................... 158
Operating Range ...................................... 162
Lifting Capacities ..................................... 167
155
SPECIFICATIONS
Main Specifications
TYPE Mono-Boom 2-Piece Boom

MASS
Machine mass kg (lb.) Rubber crawlers 7280 (16045) 7940 (17505)
(not including operator) Steel crawlers 7405 (16330) 8145 (17955)
PERFORMANCE
Bucket capacity m3 (cu.ft.) Heaped 0.245 (8.65)
(standard bucket) Struck 0.185 (6.53)
Slow speed 7.6 (7.6) / 4.1 to 7.6 (4.1 to 7.6)*
Slew speed min–1 (rpm)
Normal speed 10.7 (10.7)
Rubber 1st 2.9 (1.8)

crawlers 2nd 5.5 (3.42)
Travel speed km/h (mph)
Steel 1st 2.8 (1.74)
crawlers 2nd 5.3 (3.29)
Gradeability (degrees) 35
Ground pressure Rubber crawlers 32.9 (4.77) 35.9 (5.21)
kPa (psi) Steel crawlers 33.9 (4.91) 36.9 (5.35)
Sound-power level LWA 100 / LWA 98 **
Noise level dB(A)
Sound-pressure level LpA 75
ENGINE
Manufacturer and model Yanmar 4TNV98-VTBZ
Rated output kW / min–1 (hp / rpm) 42.8 / 2100 (57.4 / 2100)
Displacement mI (cu.in.) 3319 (202.5)
Starter V – kW 24 – 3.5
Alternator V – kW 24 – 0.96
Battery V – A·h 12 – 64 x 2
* : The maximum set speed in slow speed can be adjustable. Upon shipment, it is set to 7.6
min–1 (7.6 rpm).
** : Serial No. 17514412 ~
156
MEMO
157
SPECIFICATIONS
Machine Dimensions
Mono-Boom
V
M
Q L
R
P N
W
D
S E
K F
J G
H T U
A
L3K001
158
SPECIFICATIONS
Machine Dimensions
Mono-Boom Units: mm (inches)

Standard Arm Middle Arm Long Arm Telescopic Arm*
Rubber Crawlers Steel Crawlers Rubber Crawlers Rubber Crawlers Rubber Crawlers
A 6555 (258.1) ← 6590 (259.4) ← ←
B 2245 (88.4) ← ← ← ←
C 2570 (101.2) / 2615 (103)** 2565 (101) / 2610 (102.8)** 2570 (101.2) / 2615 (103)** ← ←
D 1720 (67.8) ← ← ← ←
E 785 (30.9) 760 (29.9) 785 (30.9) ← ←
F 2210 (87) 2180 (85.8) 2210 (87) ← ←
G 2855 (112.4) 2830 (111.3) 2855 (112.4) ← ←
H 2150 (84.6) ← ← ← ←
J 450 (17.7) ← ← ← ←
K 385 (15.1) 360 (14.2) 385 (15.1) ← ←
L 2180 (85.8) ← 2285 (90.0) 2430 (95.7) 2320 (91.3)
M 1635 (64.3) ← 1745 (68.7) 1870 (73.6) 1735 (68.3)
N 2060 (81) ← 2170 (85.5) 2310 (91) 2180 (85.9)
P 695 (27.3) ← ← ← ←
Q 735 (28.9) ← ← ← ←
R 2150 (84.6) ← ← ← ←
S 500 (19.7) ← ← ← ←
T 4840 (190.6) 4845 (190.7) 4875 (191.9) 4975 (195.9) 4925 (193.9)
U 2000 (78.7) 1995 (78.6) 2000 (78.7) ← ←
V 80° ← ← ← ←
W 50° ← ← ← ←
* : Telescopic arm fully retracted.

** : When equipped with Roof guard.
159
SPECIFICATIONS
Machine Dimensions
2-Piece Boom
V
M
Q L
R
P N
W
D
S E
K F
J G
H T U
A
L3K001
160
SPECIFICATIONS
Machine Dimensions
2-Piece Boom Units: mm (inches)

Rubber Crawlers
A 6560 (258.3)
B 2245 (88.4)
C 2570 (101.2) / 2615 (103)*
D 1720 (67.8)
E 785 (30.9)
F 2210 (87)
G 2855 (112.4)
H 2150 (84.6)
J 450 (17.7)
K 385 (15.1)
L 2505 (98.6)
M 1955 (77)
N 2385 (93.8)
P 690 (27.1)
Q 730 (28.8)
R 2150 (84.6)
S 500 (19.7)
T 4845 (190.8)
U 2000 (78.7)
V 80°
W 50°
* : When equipped with Roof guard.
161
SPECIFICATIONS
Operating Range
Mono-Boom
G
J
K
D
C
H
B
A
L3K0021
162
SPECIFICATIONS
Operating Range

Standard Arm Long Arm
Item
Rubber Crawlers Steel Crawlers Rubber Crawlers Steel Crawlers
A Max. digging radius 7055 (277.7) ← 7385 (290.8) ←
B Max. ground digging radius 6905 (271.8) 6910 (272) 7245 (285.2) 7250 (285.4)
C Max. digging depth 4240 (166.9) 4260 (167.8) 4590 (180.6) 4610 (181.5)
D Max. vertical digging depth 3475 (136.9) 3500 (137.8) 3830 (150.8) 3855 (151.8)
E Max. digging height 7025 (276.7) 7005 (275.7) 7290 (287) 7270(286.2)
F Max. dumping height 4995 (196.6) 4970 (195.6) 5255 (206.9) 5230 (205.9)
G Min. dumping height 1935 (76.3) 1915 (75.3) 1630 (64.3) 1610 (63.4)
H Max. vertical digging radius 4630 (182.3) ← 4700 (185) ←
J Max. raising height 525 (20.7) 505 (19.8) 525 (20.7) 505 (19.8)
K Max. lowering depth 410 (16.1) 435 (17) 410 (16.1) 435 (17)

Middle Arm Telescopic Arm
Item Rubber Crawlers
–– Arm Fully Retracted Arm Fully Extended
A Max. digging radius 7225 (284.4) 7065 (278.1) 8125 (319.8)
B Max. ground digging radius 7080 (278.7) 6915 (272.2) 7995 (314.8)
C Max. digging depth 4420 (173.9) 4245 (167) 5445 (214.4)
D Max. vertical digging depth 3655 (143.9) 3155 (124.3) 4365 (171.9)
E Max. digging height 7160 (281.9) 7025 (276.5) 7715 (303.8)
F Max. dumping height 5125 (201.9) 5005 (197.1) 5695 (224.3)
G Min. dumping height 1775 (69.1) 1935 (76.2) ––
H Max. vertical digging radius 4655 (183.3) 5075 (199.8) 5235 (206.1)
J Max. raising height 525 (20.7) ← ←
K Max. lowering depth 410 (16.1) ← ←
163
SPECIFICATIONS
Operating Range
2-Piece Boom
G
J
C D
H
B
A
L3L032
164
SPECIFICATIONS
Operating Range
2-Piece Boom Units: mm (inches)

A Max. digging radius 7650 (301.2)
B Max. ground digging radius 7510 (295.7)
C Max. digging depth 4440 (174.8)
D Max. vertical digging depth 3955 (155.7)
E Max. digging height 7970 (313.8)
F Max. dumping height 6000 (236.2)
G Min. dumping height 2310 (90.9)
H Max. vertical digging radius 4360 (171.6)
J Max. raising height 525 (20.7)
K Max. lowering depth 410 (16.1)
165
MEMO
166
SPECIFICATIONS
Lifting Capacities
Rated lift capacity chart

¡ The loads in the charts do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
¡ Rated lift capacities limited by rated hydraulic lift capacity are identified by an asterisk(*)
¡ The mass of slings and any auxiliary lifting devices shall be deducted from the rated load
to determine the net load that may be lifted.
¡ The load point is the bucket hinge pin, and the bucket posture is with the standard bucket
completely retracted under the arm.
¡ Units: kg (lbs.) or daN (lbs.)
Load hooking system

A load hooking system with all of the following capacities must be provided and used.
1. A system which can withstand a weight of two times the rated lift capacity no matter at
what position the load is applied.
2. A system in which there is no risk of the lifted load falling from the hooking device, for
example one equipped with a hook slippage prevention device.
3. A system in which there is no risk of the hooking system slipping from the hoe attachment.
Load safety device

In addition, the following load safety devices must be installed. (For details, contact a designated
service outlet.)
(1) An overload warning device.
(2) A boom lowering control device.
WARNING
¡ DO NOT attempt to lift or hold any load that is greater than these rated values at
their specified load radii and height.
¡ All rated lift capacities are based on the machine being level and on a firm supporting
surface. For safe working loads, the user is expected to make due allowance for the
particular job conditions such as soft or uneven ground, non-level condition, side
loads, hazardous conditions, experience of personnel, etc. The operator and other
personnel should fully acquaint themselves with the operator’s manual furnished
by the manufacturer before operating this machine, and rules for safe operation of
equipment shall be adhered to at all times.
167
Over Front ; Dozer Blade Up
1774* m ft.
(3911*)

6.0 (19.7)
5.0 (16.4)
SPECIFICATIONS
1454*
(3206*)
Lifting Capacities
1224 1479* 4.0 (13.1)

(2698) (3261*)
Equipped with Standard Arm
1211 1786 2223*

3.0 (9.8)
(2670) (3937) (4901*)
1176 1700 2714

2.0 (6.6)
(2593) (3748) (5983)
168
830
(1830)
834 2522
1.0 (3.3)
1135 1615
(1839) (2502) (3560) (5560)
1105
0 (0)
1562 2471
(2436) (3444) (5448)
2475 2994*
–1.0(–3.3)
1094 1545
(2412) (3406) (5456) (6601*)
–2.0(–6.6)
1561 2513 5065*
(3441) (5540) (11166*)
2318*
(5110*) –3.0(–9.8)
m 6.0 5.0 4.0 3.0 2.0 1.0 0

ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K0031
Over Rear Over Side
1774* m ft. 1774* m ft.

(3911*) (3911*)
6.0 (19.7)

6.0 (19.7)
5.0 (16.4) 5.0 (16.4)

SPECIFICATIONS
1454* 1454*
(3206*) (3206*)
Lifting Capacities
1385 1479* 4.0 (13.1) 982 1474

4.0 (13.1)
(3053) (3261*) (2165) (3250)
Equipped with Standard Arm
1373 3.0 (9.8) 970 1428 3.0 (9.8)

1800* 2223* 2223*
(3027) (3968*) (4901*) (2138) (3148) (4901*)
1913 2.0 (6.6) 936 1348

2.0 (6.6)
1338 3022 2091
(2950) (4217) (6662) (2064) (2972) (4610)
169
960 653
(2116) (1440)
1.0 (3.3) 1268
1.0 (3.3)
965 1298 1828 2671* 656 898 1918
(2127) (2862) (4030) (5889*) (1446) (1980) (2795) (4228)
0 (0) 0 (0)
1268 1776 2782 869 1219 1872
(2795) (3915) (6133) (1916) (2687) 4127)
–1.0(–3.3) –1.0(–3.3)
1256 1759 2787 2994* 859 1203 1876 2994*
(2769) (3878) (6144) (6601*) (1894) (2652) (4136) (6601*)
–2.0(–6.6) –2.0(–6.6)
1775 2824 5065* 1218 1910 3927
(3913) (6226) (11166*) (2685) (4211) (8658)
2318* 1987
(5110*) (4381)
–3.0(–9.8) –3.0(–9.8)
m 6.0 5.0 4.0 3.0 2.0 1.0 0 m 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K004
m ft.
7.0 (23.0)
1551*
(3419*)

6.0 (19.7)
5.0 (16.4)
SPECIFICATIONS
1187*
(2617*)
Equipped with Long Arm
Lifting Capacities
1241
4.0 (13.1)
1243*
(2736) (2740*)
1754*
(3867*)
3.0 (9.8)
866 1220 1565*
(1909) (2690) (3450*)
2.0 (6.6)
851 1178 1714 2779
(1876) (2597) (3779) (6127)
170
749
(1651)
830 1131 1618 2554
1.0 (3.3)
(1830) (2493) (3567) (5631)
812 0 (0)
1093 1551 2459
(1790) (2410) (3419) (5421)
1074 1523 2441 2596* 2219* –1.0(–3.3)

(2368) (3358) (5381) (5723*) (4892*)
1080 1527 2464 4261* 3410* –2.0(–6.6)

(2381) (3366) (5432) (9394*) (7518*)
1573 2529 –3.0(–9.8)

4621*
(3468) (5575) (10188*)
–4.0(–13.1)
m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K0051
Over Rear Over Side
m ft. m ft.
7.0 (23.0) 7.0 (23.0)
1551* 1551*
(3419*) (3419*)

6.0 (19.7) 6.0 (19.7)
5.0 (16.4) 5.0 (16.4)

SPECIFICATIONS
1187* 1187*
(2617*) (2617*)
Equipped with Long Arm
Lifting Capacities
1321* 1243*
4.0 (13.1) 4.0 (13.1)
998 1243*
(2912*) (2740*) (2200) (2740*)
1754* 1754*
(3867*) (3867*)
3.0 (9.8) 3.0 (9.8)
996 1382 1565* 685 978 1444
(2196) (3047) (3450*) (1510) (2156) (3183)
982 2.0 (6.6) 2.0 (6.6)

1340 1926 3018* 672 938 1359 2147
(2165) (2954) (4246) (6654*) (1482) (2068) (2996) (4733)
171
872 586
(1922) (1292)
961 1293 1831 2864
1.0 (3.3) 651 893
1.0 (3.3)
1270 1945
(2119) (2851) (4037) (6314) (1435) (1969) (2800) (4288)
943 1256 1765 2771 0 (0) 1208 1860

0 (0)
634 857
(2079) (2769) (3891) (6109) (1398) (1889) (2663) (4101)
1237 1737 2753 2596* 2219* –1.0(–3.3) 839 1181 1844 2596* 2219* –1.0(–3.3)
(2727) (3829) (6069) (5723*) (4892*) (1850) (2604) (4065) (5723*) (4892*)
1243 1741 2776 4261* 3410*

–2.0(–6.6) 845 1185 1864 3838 3410*
–2.0(–6.6)
(2740) (3838) (6120) (9394*) (7518*) (1863) (2612) (4109) (8461) (7518*)
1787 1228
(3940) (2707)
2840 –3.0(–9.8) 1923 –3.0(–9.8)
4621* 3958
(6261) (10188*) (4239) (8726)
–4.0(–13.1) –4.0(–13.1)
m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft. (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K006
m ft.
823* 7.0 (23.0)
(1814*)

6.0 (19.7)
SPECIFICATIONS
798* 5.0 (16.4)

(1759*)
Lifting Capacities
932 816* 4.0 (13.1)

(2055) (1799*)
915 971* 3.0 (9.8)

(2017) (2141*) 1628*
(3589*)
636 883 1225* 1374* 2.0 (6.6)
574* (1402) (1947) (2701*) (3029*)
(1265*)
172
618 843 1176 1727 2817 1582* 1.0 (3.3)
(1362) (1858) (2593) (3807) (6210) (3488*)
806 1110 1607 2583 1556* 959*

0 (0)
(1777) (2447) (3543) (5695) (3430*) (2114*)
782 1066 1536 2485 2238* 1627* –1.0(–3.3)

(1724) (2350) (3386) (5478) (4934*) (3587*)
Equipped with Telescopic Arm (Arm Fully Extended)
778 1049 1511 2468 3150* 2379*

–2.0(–6.6)
(1715) (2313) (3331) (5441) (6945*) (5245*)
1066 1528 4361* –3.0(–9.8)

2505
(2350) (3369) (5523) (9614*) 3253*
(7172*)
2447* –4.0(–13.1)
(5395*) 4242*
(9352*)
–5.0(–16.4)
m 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (26.2) (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K0071
Over Rear Over Side
m ft. m ft.
823* 7.0 (23.0) 823* 7.0 (23.0)
(1814*) (1814*)

6.0 (19.7) 6.0 (19.7)
798* 5.0 (16.4) 798* 5.0 (16.4)

SPECIFICATIONS
(1759*) (1759*)
943* 816* 4.0 (13.1) 746 816* 4.0 (13.1)

Lifting Capacities
(2079*) (1799*) (1645) (1799*)
1006* 971* 3.0 (9.8) 730 971* 3.0 (9.8)

(2218*) (2141*) 1628* (1609) (2141*) 1628*
(3589*) (3589*)
663* 1022 1225* 1374*
2.0 (6.6) 491 699 1002 1374* 2.0 (6.6)
(1462*) (2253) (2701*) (3029*) (1082) (1541) (2209) (3029*)
574* 463
(1265*) (1021)
1.0 (3.3) 1.0 (3.3)
173
735 983 1349 1952* 2993* 1582* 474 661 933 1367 2175 1582*
(1620) (2167) (2974) (4303*) (6598*) (3488*) (1045) (1457) (2057) (3014) (4795) (3488*)
0 (0) 0 (0)
947 1284 1836 2916 1556* 959* 626 870 1256 1965 1556* 959*
(2088) (2831) (4048) (6429) (3430*) (2114*) (1380) (1918) (2769) (4332) (3430*) (2114*)
–1.0(–3.3) 1189 1877 1627*

–1.0(–3.3)
922 1240 1765 2819 2238* 1627* 603 828 2238*
(2033) (2734) (3891) (6215) (4934*) (3587*) (1329) (1825) (2621) (4138) (4934*) (3587*)
Equipped with Telescopic Arm (Arm Fully Extended)
–2.0(–6.6) –2.0(–6.6)
919 1223 1741 2802 3150* 2379* 599 812 1166 1861 3150* 2379*
(2026) (2696) (3838) (6177) (6945*) (5245*) (1321) (1790) (2571) (4103) (6945*) (5245*)
–3.0(–9.8) –3.0(–9.8)
1240 1757 2839 4361* 828 1182 1895 3963
(2734) (3874) (6259) (9614*) 3253* (1825) (2606) (4178) (8737) 3253*
(7172*) (7172*)
2447* –4.0(–13.1) 1986 –4.0(–13.1)
(5395*) (4378)
4242* 4144
(9352*) (9136)
–5.0(–16.4) –5.0(–16.4)
m 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 m 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (26.2) (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft. (26.2) (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K008
1714* m ft.
(3779*)
6.0 (19.7)

1354* 5.0 (16.4)
SPECIFICATIONS
(2985*)
1247 1366* 4.0 (13.1)

Lifting Capacities
(2749) (3012*)
1220 1651* 2057* 3.0 (9.8)

(2690) (3640*) (4535*)
826 1165 1706 2737

2.0 (6.6)
(1821) (2568) (3761) (6034)
801
(1766)
174
806 1107 1587 2487 1.0 (3.3)
(1777) (2441) (3499) (5483)
2429
0 (0)
1068 1520
(2355) (3351) (5355)
–1.0(–3.3)
1058 1505 2443 2942*
Equipped with Telescopic Arm (Arm Fully Retracted)
(2332) (3318) (5386) (6486*)
–2.0(–6.6)
1536 2503 5033*
(3386) (5518) (11096*)
–3.0(–9.8)
2072*
(4568*)
–4.0(–13.1)
m 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K0091
Over Rear Over Side
1714* m ft. 1714* m ft.

(3779*) (3779*)
6.0 (19.7) 6.0 (19.7)

1354* 5.0 (16.4) 1354* 5.0 (16.4)
SPECIFICATIONS
(2985*) (2985*)
1380* 1366* 4.0 (13.1) 999 1366* 4.0 (13.1)

Lifting Capacities
(3042*) (3012*) (2202) (3012*)
1393 1651* 2057* 3.0 (9.8) 974 1466 2057* 3.0 (9.8)
(3071) (3640*) (4535*) (2147) (3232) (4535*)
967 1338 1933 3067 2.0 (6.6) 645 921 1347 2103 2.0 (6.6)
(2132) (2950) (4262) (6762) (1422) (2030) (2970) (4636)
940 623
(2072) (1373)
175
946 1281 1816 2654* 1.0 (3.3) 625 867 1237 1879 1.0 (3.3)
(2086) (2824) (4004) (5851*) (1378) (1911) (2727) (4142)
1242 1749 2764 0 (0) 1826

0 (0)
830 1174
(2738) (3856) (6094) (1830) (2588) (4026)
1233 1734 2778 –1.0(–3.3) 821 1160 1839

–1.0(–3.3)
2942* 2942*
Equipped with Telescopic Arm (Arm Fully Retracted)
(2718) (3823) (6124) (6486*) (1810) (2557) (4054) (6486*)
–2.0(–6.6) –2.0(–6.6)
1765 2837 5033* 1189 1893 3990
(3891) (6255) (11096*) (2621) (4173) (8796)
–3.0(–9.8) –3.0(–9.8)
2072* 2011
(4568*) (4433)
–4.0(–13.1) –4.0(–13.1)
m 6.0 5.0 4.0 3.0 2.0 1.0 0 m 6.0 5.0 4.0 3.0 2.0 1.0 0
ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft. (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : kg (lbs.)
L3K010
Over Front; Dozer Blade Up
m ft
8.0 (26.2)
5095*
(11453)
7.0 (23.0)
2-Piece Boom

6.0 (19.7)
1973 2181*
(4435) (4903*)
SPECIFICATIONS
5.0 (16.4)
1338 1771*
(3008) (3981*)
Lifting Capacities
4.0 (13.1)
1352 1845*
(3040) (4148*)
3.0 (9.8)
935 1319 1957 1934*
(2102) (2966) (4400) (4348*)
2.0 (6.8)
914 1263 1835
176
743 (2055) (2840) (4124)
(1671)
1.0 (3.3)
888 1205 1715
(1995) (2708) (3855)
0
868 1162 1641
(1952) (2612) (3689) 1696*
(3814*)
-1.0 (–3.3)
869 1145 1618 2598
(1953) (2574) (3637) (5839)
-2.0 (–6.6)
1162 1636 2646 3452*
(2611) (3679) (5948) (7760*)
-3.0 (–9.8)
978*
(2198*)
-4.0(–13.1)
7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
(23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : daN (lbs.)
L3L0331
Over Rear Over Side
m ft m ft
8.0 (26.2) 8.0 (26.2)
5095* 5095*
(11453) (11453)
7.0 (23.0) 7.0 (23.0)
2-Piece Boom

6.0 (19.7) 6.0 (19.7)
2012* 2181* 1564 2181*
(4524*) (4903*) (3516) (4903*)
SPECIFICATIONS
5.0 (16.4) 5.0 (16.4)

1490 1771* 1062 1637
(3349) (3981*) (2388) (3681)
Lifting Capacities
4.0 (13.1) 4.0 (13.1)

1504 1845* 1075 1622
(3380) (4148*) (2417) (3647)
3.0 (9.8) 3.0 (9.8)
1058 1471 2117* 1934* 730 1044 1549 1934*
(2379) (3307*) (4760*) (4348*) (1641) (2347) (3483) (4348*)
2.0 (6.8) 2.0 (6.8)
1038 1416 2033 710 991 1435
177
853 (2333) (3182) (4571) 568 (1596) (2228) (3226)
(1918) (1276)
1.0 (3.3) 1.0 (3.3)
1011 1357 1914 684 935 1323
(2273) (3051) (4303) (1538) (2102) (2975)
0 0
992 1315 1842 666 895 1255
(2229) (2956) (4140) 1696* (1496) (2011) (2821) 1696*
(3814*) (3814*)
-1.0 (–3.3) -1.0 (–3.3)
992 1298 1819 2888 666 879 1233 1930
(2230) (2918) (4088) (6493) (1497) (1976) (2772) (4339)
-2.0 (–6.6) -2.0 (–6.6)
1315 1837 2666* 3452* 894 1250 1973 3452*
(2955) (4129) (5994*) (7760*) (2011) (2811) (4436) (7760*)
-3.0 (–9.8) -3.0 (–9.8)
978* 978*
(2198*) (2198*)
-4.0(–13.1) -4.0(–13.1)
m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft (23.0) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units : daN (lbs.)
L3L034
m ft
7.0 (23.0)
1679*
(3774*)
6.0 (19.7)

5.0 (16.4)
1335*
SPECIFICATIONS
(3001*)
4.0 (13.1)
1298 1381*
Lifting Capacities
Equipped with Middle Arm
(2917) (3105*) 2018*

(4537*) 3.0 (9.8)
1280 1707*
(2876) (3838*)
2.0 (6.6)
895 1238 1794 2855
813 (2013) (2783) (4033) (6485)
(1828)
178
1.0 (3.3)
876 1191 1697 2660
(1970) (2678) (3814) (5980)
0
861 1155 1633 2581
(1935) (2597) (3672) (5803)
-1.0 (-3.3)
1139 1610 2575 2825*
(2561) (3619) (5789) (6350*)
-2.0 (-6.6)
1154 1621 2609 4702*
(2594) (3644) (5865) (10571*)
-3.0 (-9.8)
2646* 4157*
(5948*) (9345*)
-4.0 (-13.1)
m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft (23) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units: daN (lbs.)

Over Rear Over Side
m ft m ft
7.0 (23.0) 7.0 (23.0)
1679* 1679*
(3774*) (3774*)
6.0 (19.7) 6.0 (19.7)

5.0 (16.4) 5.0 (16.4)
1335* 1335*
SPECIFICATIONS
(3001*) (3001*)
4.0 (13.1) 4.0 (13.1)
1429* 1381* 1040 1381*
Lifting Capacities
Equipped with Middle Arm
(3213*) (3105*) 2018* (2340) (3105*) 2018*

(4537*) 3.0 (9.8) (4537*) 3.0 (9.8)
1438 1707* 1023 1508
(3232) (3838*) (2301) (3391)
2.0 (6.6) 2.0 (6.6)
1024 1397 2001 3183 705 984 1420 2222
934 (2301) (3140) (4499) (7157) 637 (1586) (2213) (3192) (4994)
(2101) (1432)
179
1.0 (3.3) 1.0 (3.3)
1005 1350 1905 2963 687 940 1329 2020
(2259) (3036) (4283) (6660) (1544) (2113) (2988) (4541)
0 0
989 1315 1842 2885 672 906 1270 1949
(2224) (2955) (4142) (6486) (1511) (2036) (2856) (4381)
-1.0 (-3.3) -1.0 (-3.3)
1299 1819 2879 2825* 890 1248 1944 2825*
(2920) (4089) (6473) (6350*) (2002) (2806) (4369) (6350*)
-2.0 (-6.6) -2.0 (-6.6)
1313 1830 2912 4702* 904 1259 1974 4058
(2952) (4115) (6547) (10571*) (2033) (2830) (4438) (9122)
-3.0 (-9.8) -3.0 (-9.8)
2646* 4157* 2047 4157*
(5948*) (9345*) (4603) (9345*)
-4.0 (-13.1) -4.0 (-13.1)
m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 m 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0
ft (23) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3) ft (23) (19.7) (16.4) (13.1) (9.8) (6.6) (3.3)
Units: daN (lbs.)

180
OPTIONS
General Precautions ................................ 182
Safety Signs (Decals) ............................... 184
Biodegradable Oil .................................... 186
Switching the Lever Pattern .................... 187
Attachment Combination Table ............... 188
Telescopic Arm ........................................ 189
Hydraulic Breaker .................................... 192
3-Hole Bucket ........................................... 194
Travel Alarm ............................................. 195
Load Safety Device .................................. 196
Fuel Supply Pump .................................... 198
Accumulator ............................................. 199
Second Auxiliary Hydraulics ................... 200
Third Auxiliary Hydraulics ....................... 202
Fourth Auxiliary Hydraulics ..................... 204
Air Conditioner ......................................... 206
Throttle Lever ........................................... 215
Immobilizer System ................................. 216
181
OPTIONS
General Precautions
Precautions on Safety
WARNING
Heed the following when removing or installing an attachment or option:
¡ Consult with a Takeuchi dealer before installing optional attachments.
¡ Do not use attachments that have not been approved by Takeuchi or a Takeuchi
dealer. Doing so may compromise safety or adversely affect the machine’s operation
or service life.
¡ Takeuchi will not be held responsible for any injuries, accidents or damage to
products caused by the use of a non-approved attachment.
¡ Choose a flat, hard surface to perform the operations. Also make sure there is enough
light and good ventilation.
¡ Clean the area, remove any articles that may get in the way or be dangerous, and
remove any spilt oil or grease.
¡ When performing lifting operations, determine a person to lead the operations and
always follow that person’s instructions.
• Follow the leader’s instructions on operating methods and procedures.
• Determine a signal leader and heed this person’s signals.
¡ When removing or installing the hoe attachment, place it in a stable position so that
it does not tip over.
¡ Due to the risk of loads falling and/or hitting people, do not allow unauthorized
personnel in the work area.
¡ Use the crane to carry heavy objects (25 kg (55 lb.) or greater).
¡ When removing heavy parts, be sure to prop them up before removing them. When
lifting them with a crane, be careful to balance them properly.
¡ Operating with loads suspended with the crane is dangerous. Place loads on a
stand and check for safety.
¡ When attaching the boom or arm, failure to follow proper procedures could result in
serious damage. Consult with a Takeuchi dealer beforehand.
Precautions on Installing Attachments

After replacing optional attachments or other special attachments, test-run them, then inspect
the hydraulic oil level and add oil if necessary.
In addition, consult with a Takeuchi dealer for details of removal and installation procedures.
182
OPTIONS
General Precautions
Precautions on Operating Attachments
WARNING
Long attachments reduce machine stability. When traveling down steep slopes or
slewing on slopes, the machine may loose its balance and tip over.
The following operations are particularly dangerous. Do not perform them.
¡ Traveling down slopes ¡ Traveling across slopes ¡ Slewing on slopes
with the attachment lifted
OE3A2531 OE3A271 OE3A331
¡ When heavy attachments are installed, the overslew (the distance from where the
operation to stop slewing is performed until slewing stops completely) increases
and mistakes in judgment may result in the attachment hitting surrounding objects.
Allow for plenty of room between the attachment and obstacles.
In addition, the natural drop (the gradual dropping of the attachment under its own
weight when it is stopped in midair) also increases when heavy attachments are
installed.
¡ The machine can tip over more easily in the lateral direction than in the longitudinal
direction.
• Do not slew (swing) sideways with excessive weight at the front. In particular do
not slew sideways on slopes.
• The front is heavier for machines equipped with breakers, crushers or telescopic
arms than for machines equipped with the standard bucket. Do not operate such
machines sideways, especially with the digging arm (boom) downhill.
¡ When a long arm or a telescopic arm is installed, the operating range suddenly
increases and mistakes in judgment may result in the attachment hitting surrounding
objects. Allow for plenty of room between the attachment and obstacles.
183
OPTIONS
Keep all safety signs clean and legible.

Replace all missing, illegible or damaged safety and warning signs.
There are other safety signs in addition to the ones listed here. Treat them in the same way.
L3L0121
184
OPTIONS
1. No.03593-32200 2. No.03593-32300
G A
(ISO)
WARNING
Check what type of lever control
arrangement you are operating
03593-32300
03593-32200
3. No.05693-38100
185
OPTIONS
Biodegradable Oil
Biodegradable oil
Biodegradable oil is a new type of hydraulic oil that is decomposed into carbon dioxide and
water by microorganisms in the soil and water. It is highly safe for living organisms and offers
advantages in terms of environmental protection.
¡ Recommended biodegradable oil: Mobile EAL Envirosyn 46H (an ester synthetic oil).
When replacing the hydraulic oil with biodegradable oil, use the above or an equivalent oil.
Note that other oils, even other brands of ester synthetic oils, may damage O-rings, packings
and seals. Takeuchi products shipped with the optional biodegradable oil are shipped with
the above brand of oil.
¡ When switching from a mineral oil to a biodegradable oil, the parking brake torque decreases
by about 30%.
Replacing the hydraulic oil with biodegradable oil

Mixing mineral oil with biodegradable oil will result in a decrease of the hydraulic oil’s
performance as well as a decrease in biodegradability and safety. The hydraulic oil system
must be flushed as described below before supplying the biodegradable oil. This operation is
dangerous and requires experience. Have it performed by a Takeuchi sales or service outlet.
Flushing
¡ To be performed by a Takeuchi sales or service outlet
1. Drain the hydraulic oil (mineral oil) from the hydraulic tank and clean the inside of the tank
and suction strainer. (Refer to the section on replacing the hydraulic oil and cleaning the
suction strainer.)
2. Remove the cylinder hoses and drain the hydraulic oil (mineral oil) from inside the cylinders.
3. Supply new biodegradable oil to the hydraulic tank.
4. Bleed the air from the hydraulic pump, control valve, slew motor and cylinders.
5. Operate the hydraulic devices for 30 minutes.
6. Drain the biodegradable oil from the tank and cylinders.
7. Replace the hydraulic oil return filter with a new filter.
8. Repeat steps 3 and 4.
9. Operate the hydraulic devices for 30 minutes.
12. Operate the hydraulic devices for 1 hour.
14. Replace the return filter with a new filter.
16. Operate the hydraulic devices, then check for oil leakage.
¡ There is no need to flush the hydraulic oil system when switching from biodegradable to
mineral hydraulic oil.
186
OPTIONS
Switching the Lever Pattern
The operating pattern of the left and right operating levers can be changed.
WARNING
Before starting the engine, check the selector to see which operating pattern the left
and right operating levers are set for.
A
ISO
G
JCB
C4L004
Switching the Lever Pattern
1. Park the machine in a safe place and turn

2 3 1
off the engine.
2. Fully open the cab door and fix it in place.
3. Lift up the floor mat at the cab entrance.
4. Open the cover (1).
A G 5. Loosen the wing bolt (2).
6. Turn the selector valve lever (3) and switch
L3L0021 the pattern.
7. Tighten the wing bolt (2) and fasten the
(A) : ISO pattern
lever (3) in place.
(G) : JCB pattern
8. Close the cover (1) and set the floor mat
back in place.
9. Check the lever pattern.
187
OPTIONS
Attachment Combination Table
Below is the bucket combination table for when standard arm, long arm and telescopic arm
are installed.
Heed this table.
WARNING
¡ Add an extra weight when using a telescopic arm.
¡ Add an extra weight or replace with wide steel crawler belts when using a long arm.
¡ Install a swing stopper when a bucket wider than the standard bucket or a telescopic
arm is installed.
√ : Usable
∆ : Usable for light operations (digging and loading operations with dry, loose or mud)
– : Not usable
Total bucket weight = Weight of bucket + Weight of full bucket load (specific gravity : 1.8)
Bucket Standard Telescopic

Rated cutting Arm Middle Arm Long Arm Arm
Bucket Capacity width 1780 mm 1960 mm 2130 mm 1780 to 2990 mm
m3 (cu.yd.) mm (inch) (70 in.) (77 in.) (84 in.) (70 to 118 in.)
430W (without
Side cutter ) 0.14 (0.18) 430 (16.9) √ √ √ √
500W 0.14 (0.18) 500 (19.7) √ √ √ √
650W 0.20 (0.26) 650 (25.6) √ √ √ √
750W (S.T.D.) 0.25 (0.33) 750 (29.5) √ √ √ —
3-hole Bucket
(without Side cutter)
0.26 (0.34) 610 (24.0) √ — — —
Total bucket weight = Within 530kg Within 750
√ √ √ √
for Telescopic Arm (1168 lb.) (29.5)
Total bucket weight = Within 657kg Within 750
√ — — —
(1448 lb.) (29.5)
Hydraulic Breaker (TKB 401) √ — — —
188
OPTIONS
Telescopic Arm
Extending and Retracting the Caution on Using the Arm

Arm
Use the auxiliary hydraulics controls to
extend and retract the telescopic arm.
A
B
OE3A331
¡ The machine may loose balance and tip

over when slewing or operating the
L3L035 attachment on slopes. It is particularly
dangerous to slew with the arm extended
on the bucket full. Never do so.
B A
OL1L040
(A) Retract
(B) Extend
OL1L060
WARNING ¡ NEVER slew suddenly or stop slewing

suddenly with the arm extended. Doing
¡ Excavator must be equipped with
so may damage the arm.
boom swing stopper.
¡ Use caution when operating.
Telescopic arm reduces craning
capacity and bucket may come into
contact with excavator. Excavator may
become unstable when operating over
the side or with boom swing.
¡ SAE heaped capacity of bucket
installed on telescopic arm must not
exceed 0.201 m3 (7.1 cu.ft.).
¡ Do not install hydraulic breaker,
compactor or similar attachment on
telescopic arm.
189
OPTIONS
Telescopic Arm
OL1L070 OL1L100
¡ Do not operate on base rock or hard soils,

as doing so may shorten the arm’s service
life.
OL1L110
¡ Do not put the arm under water. Also avoid

moisture when storing.
OL1L080
¡ Do not change directions with machine

lifted by pressing the bucket pressed
against the ground. Doing so may damage
the arm.
OL1L120
¡ The arm pressing speed is slow when

pressing the arm while simultaneously
extending it, but the arm pressing speed
suddenly comes faster when the arm
extending operation is stopped or the
OL1L090
cylinder end is reached. Be careful not to
¡ When dumping soil from the bucket or hit surrounding objects.
shaking the bucket to remove the
remaining soil, do so with the arm retracted
to protect the arm extension/retraction
section.
190
OPTIONS
Telescopic Arm
Inspection and Maintenance

Greasing
¡ Every day or every 10 hours
¡ Type of grease ..... Lithium-based multi-
purpose grease No. 2
¡ Greasing points
OL1L130
1. Fully extend the bucket and arm cylinders,

lower the boom and on top of block the
bucket.
2. Lower the dozer blade and stop the
engine.
3. Clean the grease nipple.
4. Add grease to the grease nipple using a
grease gun.
5. Wipe off the grease that has been
squeezed out and any extra grease.
Looseness in the telescopic arm

When the telescopic arm is used for long
periods of time, wear may cause the gap
between the outside arm and inside arm to
increase to above the set value, resulting in
looseness.
Other parts may be damaged if the telescopic
arm is used with such looseness. Contact a
Takeuchi dealer for maintenance.
Note that no maintenance is necessary other
than the greasing described above.
191
OPTIONS
Hydraulic Breaker
For handling of the breaker, read the

hydraulic breaker’s manual, provided
separately.
IMPORTANT: When mounting devices,

select devices suited for this machine.
For advice on selecting device, contact a
Takeuchi sales or service outlet.
¡ Do not pry with the chisel, and do not pry

while pounding.
¡ Do not move the chisel while pounding.
¡ Do not pound continuously for over 30
seconds on the same surface.
Precautions on Operating
L FC H
¡ Do not pound with the cylinder fully

L3D008
extended or contracted (at the stroke end).
¡ Run the engine with 75% the maximum Leave a margin of at least 5 cm.
speed.
Pressing force
¡ Do not pound with the arm perpendicular

¡ Pound with the chisel perpendicular to the to the ground surface.
surface you are pounding.
¡ When pounding, press the chisel properly
against the object to be broken so as to
avoid pounding the air.
192
OPTIONS
Hydraulic Breaker
Replace the hydraulic oil

regularly!
When using a hydraulic breaker, the oil
deteriorates quicker than during normal
digging. Be sure to replace the hydraulic oil
and return filter element.
¡ Failure to replace these in time can lead
to damage to the machine and breaker’s
¡ Do not drop the breaker itself on the object hydraulic systems. In order to improve the
to be broken in order to break it. service life of the hydraulic systems, be
¡ Do not move objects to be broken or rocks sure to replace the hydraulic oil and return
with the breaker itself. filter element after the number of hours
¡ Slew occasionally to cool the engine. shown on the diagram below.
¡ If a hydraulic hose is vibrating abnormally, ¡ Clean the suction strainer when changing
nitrogen gas may be leaking from the the return filter element.
accumulator. Have an inspection as soon
as possible.
Replacement Interval (Hours)
Item Hydraulic Oil Filter Element

1st time 25
2nd time 100
Periodically 600 200
When the breaker operating ratio is 100%
2000
Replacement interval
for hydraulic oil
1500
Replacement interval (H)
1000
Replacement
500 interval for filter element
0 20 40 60 80 100
Breaker operating ratio (%)
N0G036
193
OPTIONS
3-Holes Bucket
A B
OL1L170
OL1L180
The digging capacity increases when the

bucket’s link arm installation position is
switched from (A) to (B). However, this
shortens the bucket stroke.
• Struck capacity (SAE):
0.210 m3 (0.275 cu. yd.)
• Rated capacity (SAE):
0.261 m3 (0.341 cu. yd.)
Changing the Link Arm

Installation Position
Refer to page 134 “Replacing the Bucket” in
the manual.
194
OPTIONS
Travel Alarm
Factory option Fuse Layout and Circuits Protected

An alarm is sounded when the machine
travels and stops when traveling is stopped.
If the alarm does not sound when the 15A Horn, 3A Throttle controller
machine travels, the fuse may be blown. Interior Light (B)
Inspect the fuse. 10A Proportional control 1A Stop solenoid hold
solenoid
WARNING 20A Lights 10A External power socket,
Travel alarm
If the fuse which has just been replaced 20A Wiper 10A Cigarette lighter
should blow again, there is a problem in
the electrical system. This could cause 5A Radio 10A Lever lock
fires. Contact a Takeuchi dealer.
5A Heater 10A Automatic-glow
30A Air conditioner 20A Throttle controller

10
10
20
(option) (ACC)
10
20
10
10
20A Instrument cluster, 20A Feed pump,
20
5
10
10
Lift alarm (option) Stop solenoid timer
5
20
20
10
20
1
L3J002
Blown Normal
E4J007
1. Park the machine in a safe place.

2. Set the starter switch to OFF.
3. Open the fuse box cover (1).
4. Inspect for blown fuse.
5. If a fuse is blown, replace it with a spare
fuse of the same capacity.
195
OPTIONS
Load Safety Device
The load safety devices include an Intermediate Boom / Type B

emergency shut-off valve and an overload
warning device. The emergency shut-off
valve stops the boom or arm part way
through a fall. The overload warning device
sounds an alarm when an excessive load is
applied.
Emergency shut-off valve

When the hose of the boom or arm cylinders Arm / Type B
are ruptured and the boom or arm falls, the
emergency shut-off valve is activated and 2
stops the boom or arm part way through the
fall.
WARNING
If the boom or arm drops and the
N0L003
emergency shut-off valves are activated,
immediately move away from the If the emergency shut-off valves (1) or (2)
suspended object. are activated, immediately set the operating
lever to the neutral position. Do not move
Mono-Boom / Type A or B the operating lever to the boom or arm
lowering side. Contact a Takeuchi dealer for
maintenance.
Type A
3 4
2-Piece Boom / Type B
1 L3L014
1. Check for safety in the working area and

for stability of the machine and lifted load.
2. Loosen the emergency shut-off valve’s
lock nut (3) and stem (4) to lower the
boom.
3. Check for stability of the hoe attachment
and load.
196
OPTIONS
Load Safety Device
4. Tighten the stem (4) secure it with the lock

Overload Warning Device
nut (3).
Tightening torque: If a weight greater than the machine is
• Stem (4) 1.0 to 1.5 N·m (0.7 to 1.1 ft-lb.) designed to lift is lifted, the overload warning
• Lock nut (3) 3.2 N·m (2.4 ft-lb.) device is activated and a horn is sounded
(when the overload warning switch is turned
Type B on).
If the engine can be started, the boom or
arm can be lowered with the operating lever. WARNING
Check for safety, then slowly lower the boom
or arm. Continuing to apply the load after the
If the engine cannot be started, the boom or overload warning horn sounds could
arm can be lowered using the procedure result in the machine tipping over or the
described below. emergency shut-off valve being activated.
If the horn sounds, stop operating the
machine and lighten the load.
2 4 5 3
N0L0061
2
1. Check for safety in the working area and L3L0061
for stability of the machine and lifted load.
2. Remove the cap (3). Overload warning switch (2)
3. Loosen the lock nut (4). O position .... OFF
4. Tighten the stem (5) to lower the boom or I position .... ON When the emergency
arm. shut-off valve is activated, the overload
5. Check for stability of the hoe attachment warning horn stops. (This is because the
and load. pressure sensor can no longer detect
6. Loosen the stem (5) secure it with the lock hydraulic pressure.)
nut (4).
197
OPTIONS
Fuel Supply Pump
This device automatically supplies fuel to the

fuel tank and stops automatically when the
fuel tank is full.
DANGER
Do not use the fuel supply pump for
gasoline or hydraulic oil. Doing so could
result in explosion or damage. Only use
the fuel supply pump for diesel fuel.
1
2
L3L013
1. Open the front cover.

2. Insert the pump’s nozzle (1) in the fuel
supply tank.
3. Press the switch (2).
The pump stops automatically once the
fuel tank is full.
198
OPTIONS
Accumulator
Operating the Machine with

Accumulator
On machines equipped with an accumulator,
the residual pressure in the auxiliary
hydraulic circuits and the working equipment
can be released within a specific amount of
time (within 10 minutes) after the engine is
stopped.
7. Move or press the second / fourth auxiliary
Releasing the residual pressure hydraulic switches (C / G) and (D / H)
After using the machine, pressure remains several times to release the residual
in the hydraulic circuits. This is called the pressure in the circuitry.
residual pressure. Use the procedure below When equipped with fourth auxiliary
to release the residual pressure as hydraulics.
necessary. a. Press the selector button (2nd or 4th
Aux.) to change over to operation of the
Perform the operation to release the residual second auxiliary hydraulics.
pressure within 10 minutes after stopping the b. Move or press the second / fourth
engine. auxiliary hydraulic switches to the right
and left several times.
1. Press the decel. button and idle the engine 8. Move all the control levers and pedals
at low speed. several times in all directions to release
2. Lower the bucket and dozer blade to the the pressure from the working equipment
ground. circuitry.
3. Check that the safety lock lever is in the 9. Raise the safety lock lever to engage the
released position. lock.
4. Stop the engine.
5. Turn the starter switch to the ON position. Lowering the boom when the engine has
stopped.
Perform this operation within 10 minutes after
stopping the engine.
A 1. Check that the safety lock lever is in the
released position.
B
2. Check that the starter switch is in the ON
position.
3. Push the operating lever slowly forward
to lower the boom.
L3L035
6. Press both the first auxiliary hydraulic

buttons (A) and (B) several times to
release the residual pressure in the
circuitry.
199
OPTIONS
Second Auxiliary Hydraulics

Second Auxiliary Hydraulic Lines
WARNING air from the hydraulic lines.
Oil may spurt out if caps or filters are c. Stop the engine and wait for more than
removed or pipes disconnected before 5 minutes until bubbles escape from the
releasing the pressure in the hydraulic hydraulic oil in the tank.
system.
¡ When disconnecting hoses, release the IMPORTANT: Follow the procedures for
internal pressure before removing. purging air as instructed by the
attachment manufacturer if specified to
These lines deliver the hydraulic oil do so.
necessary for operating a hydraulic
attachment. 6. Check for leaks.
S O
d
c
L3L036
Stop valve ..... S : Closed O : Open

use the following procedures:
When equipped with accumulator:
Refer to page 201 “Releasing the residual
pressure”.
ports (c) and (d).
4. Open the stop valves.
5. When connecting is complete, purge air
from the hydraulic lines.
a. Start and run the engine at low idle with
no load for 10 minutes.
200
OPTIONS
Second Auxiliary Hydraulics
Second Auxiliary Hydraulic 4. Within 10 minutes after the engine comes

to a complete stop, move or press the
Switches
second auxiliary hydraulic switches to the
Slider switch (Proportional control) and right and left several times.
Buttons 5. Raise the safety lock lever to engage the
lock.
Move or press those switches to control the

flow of the oil in the second auxiliary hydraulic
lines.
(C) ..... Hydraulic oil flows to left auxiliary
line(c)
(D) ..... Hydraulic oil flows to right auxiliary
line(d)
¡ When the safety lock lever is set to the

lock position, this control is locked.

When equipped with accumulator:
Refer to “Releasing the residual pressure.”
2. Disconnect the lines from ports (c) and (d).
When equipped with accumulator

Releasing the residual pressure
After using the auxilliary hydraulic circuits,
1. Stop the engine.
2. Turn the starter switch to the ON position.
3. Fully lower the safety lock lever.
201
OPTIONS
Third Auxiliary Hydraulics
IMPORTANT: Follow the procedures for

Third Auxiliary Hydraulic Lines
purging air as instructed by the
attachment manufacturer if specified to
WARNING do so.
Oil may spurt out if caps or filters are
removed or pipes disconnected before 5. Check for leaks.
releasing the pressure in the hydraulic
system.
¡ When disconnecting hoses, release the
internal pressure before removing.

necessary for operating a quick attachment.

use the following procedures:
lines.
ports (e) and (f).
air from the hydraulic lines.
5 minutes until bubbles escape from the
hydraulic oil in the tank.
202
OPTIONS
Third Auxiliary Hydraulics
Third Auxiliary Hydraulic Switch Third Auxiliary Hydraulics

and Button Warning Lamp
L3L029 L3L030
Press those switch and button to control the This lamp illuminates and an alarm sounds
flow of the oil in the third auxiliary hydraulic when the third auxiliary hydraulic pressure
lines. drops abnormally while the engine is running.
When the safety lock lever is released after
the engine is started, hydraulic oil constantly
flows in pipe (e). When button (1) and switch
(2) are pressed simultaneously, the oil flow
switches to pipe (f). When this happens, the
pressure of pipe (e) drops, an alarm is
sounded and the warning lamp lights. For
safety, only operates when both button (1)
and switch (2) are pressed.

lines.
2. Disconnect the lines from ports (e) and
(f).
Releasing the residual pressure

After using the auxilliary hydraulic circuits,
1. Stop the engine.
(The residual pressure is released from
the (e) port line.)
203
OPTIONS
Fourth Auxiliary Hydraulics

Fourth Auxiliary Hydraulic Lines
5 minutes until bubbles escape from the
hydraulic oil in the tank.
WARNING
Oil may spurt out if caps or filters are IMPORTANT: Follow the procedures for
removed or pipes disconnected before purging air as instructed by the
releasing the pressure in the hydraulic attachment manufacturer if specified to
system. do so.
¡ When disconnecting hoses, release the
internal pressure before removing. 5. Check for leaks.

necessary for operating a hydraulic
attachment. Selector Button (2nd or 4th Aux.)
Connecting the Hydraulic Circuits This button changes from the fourth auxiliary
To connect the attachment hydraulic lines, hydraulics operation to the second auxiliary
use the following procedures : hydraulics operation.
1. Release the pressure remaining in the Press this button to change over to operation
lines. of the second auxiliary hydraulics. The
When equipped with accumulator: second auxiliary hydraulics operation
Refer to page 199 “Releasing the residual indicator lamp will light. One more press of
pressure”. this button will result in a return to fourth
2. Remove the plugs. auxiliary hydraulics operation. Actual
3. Connect the attachment hydraulic lines to operation is performed with the second /
ports (g) and (h). fourth auxiliary hydraulic switches.
air from the hydraulic lines.
204
OPTIONS
Fourth Auxiliary Hydraulics
Second / Fourth Auxiliary Selector Button (2-Piece boom)

Hydraulic Switches
Slider switch (Proportional control) and WARNING
Buttons Pressing (switching ON or OFF) the
selector button while the boom swing
pedal is depressed is dangerous, since
the attachment will move unexpectedly.
Always set the boom swing pedal back
to the neutral position before operating
the selector button.
Move or press those switches to control the

flow of the oil in the fourth auxiliary hydraulic
lines.
(G) ..... Hydraulic oil flows to left auxiliary

line(g)
(H) ..... Hydraulic oil flows to right auxiliary
line(h) This button changes from the boom swing
operation to the intermediate boom
¡ When the safety lock lever is set to the operation.
lock position, this control is locked. Press this button to change over to operation
of the intermediate boom . The intermediate
Disconnecting the hydraulic circuits boom operation indicator lamp will light. One
1. Release the pressure remaining in the more press of this button will result in a return
lines. to boom swing operation. Actual operation
When equipped with accumulator : is performed with the boom swing pedal.
Refer to page 199 “Releasing the residual Operation of the first auxiliary hydraulic
pressure”. switch push button: left side (A) only.
2. Disconnect the lines from ports (g) and
(h).
205
OPTIONS
Air Conditioner
CAUTIONS ON USE Do not overcool

For health purposes, the air inside the cab
Ventilate periodically
should be kept at a temperature at which you
¡ When using the air conditioner over an feel a little cool when entering the cab from
extended period of time, open the outside (a difference of 5 to 6°C (9 to 11°F)).
windows about once each hour to let in Be careful to adjust the temperature properly.
fresh air.
¡ Your eyes may become irritated if you
smoke while using the air conditioner. If Do not turn the air conditioner on
this happens, open the windows to let in until the engine is started
fresh air. Cigarette smoke particularly
To avoid placing an excessive load on the
irritates the eyes when using the air
compressor, wait until the engine is started
conditioner because the humidity in the
and is running smoothly before turning on
cabin drops and the eyes’ membranes
the air conditioner.
tend to become dry.
¡ If the outside air is dirty, set the air
conditioner to the recirculation mode.
Let hot air out first
If the excavator has been parked in the sun,
Always maintain good visibility open the windows or door to let the hot air
out of the cab before using the air conditioner.
Working with the windows dirty or fogged
restricts visibility and is dangerous. Always
clean dirt and moisture off the windows
before working. Caution on refrigerant (gas)
¡ The windows tends to get foggy when the
humidity is high. If this happens, turn on Exposure of the eyes or hands to the cooler’s
the air conditioner and use outside air and refrigerant could result in blindness or
the defroster to get rid of the fog. frostbite. Never touch the refrigerant or
¡ If the air conditioner is set to high when loosen the parts of the cooling circuit.
using the defroster, the difference between Should the refrigerant gas leak, keep flames
the external and internal temperatures away.
increases, and fog may form on the
outside of the windows. If this happens,
either turn the air conditioner off or turn
the temperature control dial clockwise to
increase the internal temperature.
¡ Mist may blow out of the air outlets. This
is not a malfunction. When moist air
passes through the air conditioner unit’s
evaporator, water particles in the air freeze
and are emitted as mist.
206
OPTIONS
Air Conditioner
NAMES OF COMPONENTS
5 5
6
1
7
2
3 10
8
4
L3T001
1. Defroster Control Panel

2. Condenser
3. Receiver drier
4. Foot outlets
5. Back outlets
6. Control panel
7. Compressor
8. Air conditioner unit
9. External air duct 11 12 13 14
L3T0021
10. Filter
11. Air conditioner switch
12. Temperature control dial
13. Fan switch
14. Airflow mode control dial
207
OPTIONS
Air Conditioner
Air Conditioner Switch Temperature Control Dial

IMPORTANT: To avoid placing an
excessive load on the compressor, wait
until the engine is started and is running
smoothly before turning on the air
conditioner.
COOL WARM
L3T005
Use this dial to adjust the air temperature.

COOL ..... To lower the temperature
WARM .... To increase the temperature
Supplement: No warm air is emitted if the
L3T006
temperature of the engine coolant is low.
Use this switch to turn the air conditioner ON
and OFF. When this switch is pressed while
the engine is running and the fan switch is
Fan Switch
ON, the air conditioner turns on. Press the
switch again or turn the fan switch OFF to
stop the air conditioner.
O ...... OFF
I ....... ON
Supplement: To prevent leakage of coolant
gas from the compressor’s seal, operate the
air conditioner at least once a week,
regardless of the season.
L3T003
Supplement: The air conditioner will not
function if the temperature in the cab is low Use this switch to adjust the fan speed in
(about 3°C (38°F) or lower). three steps. At the OFF position, the air
conditioner is also OFF.
OFF ........ Fan and air conditioner off
............. Low
............. Medium
............ High
208
OPTIONS
Air Conditioner
Airflow Mode Control Dial OPERATION
Heating and Dehumidifying

(in cold weather or when the
humidity is high)
L3T004
Use this dial to select recirculation or fresh

air intake.
............... Recirculation
L3T008
• To cool or heat the cab quickly
• When external air is dirty After starting the engine, turn the air
CENTER .... 50% fresh air intake conditioner ON and adjust the switches as
• To let in fresh air shown in the diagram above.
• To ventilate while cooling or heating the The outflow slot of foot area and the outflow
cab slowly slots of the defroster can be directed at the
............. Fresh air intake front window.
• To let in fresh air Warm, dehumidified air blows on the front
• To remove fog from the windows window, preventing fogging.
• To ventilate while cooling or heating the Set the temperature control dial and fan
cab switch to the desired positions.
Outlets Cooling
CAUTION
¡ When the air conditioner is set to the
recirculation mode, the air in the cab
gradually becomes dirty, so switch to
external air to ventilate once a
comfortable temperature is reached.
L3T007 ¡ Excessive cooling can be harmful to
your health. It is best to keep the air
Move the louvers up and down or left and inside the cab only about 5 to 6°C (9 to
right to adjust the air flow direction and 11°F) cooler than the outside air.
amount. ¡ If the excavator has been parked in the
sun, open the windows or door to let
the hot air out of the cab before using
the air conditioner.
209
OPTIONS
Air Conditioner
Defogging the Windows
CAUTION
If the air conditioner is set to high when
using the defroster, the difference
between the external and internal
L3T009 temperatures increases, and fog may
After starting the engine, turn the air form on the outside of the windows. If
conditioner ON and adjust the switches as this happens, either turn the air
shown in the diagram above. conditioner OFF or turn the temperature
Set the temperature control dial and fan control dial clockwise (WARM).
switch to the desired positions.
Quick cooling
L3T009
After starting the engine, turn the air

L3T010 conditioner ON and adjust the switches as
To cool the cab quickly, set the airflow mode shown in the diagram above.
control dial to the recirculation position and The outflow slot of foot area and the outflow
the fan switch to High, as shown on the slots of the defroster can be directed at the
diagram above. front window.
210
OPTIONS
Air Conditioner
Inspection
INSPECTION AND MAINTENANCE
1. Open the engine hood.
Inspection and maintenance interval 2. Press on the center of the belt (1) with a
............................ Every 250 hours finger. The belt’s tension is normal if it
bends about 8 mm (0.3 in.) when pressed
Inspecting and Adjusting the Air with a force of about 98N (22 lbs).
Conditioner Belt
Adjustment
Inspection and maintenance interval If the belt’s tension is not normal, adjust it
... After first 50 hours (New machines only) with the adjust bolt (3).
IMPORTANT: Do not let any oil or grease 1. Loosen the nut (4).
get on the belt, as it will cause the belt to 2. Tighten the bolt (3) to decrease the tension.
slip, shortening its service life and Loosen the bolt (3) to increase the tension.
reducing the air conditioner’s cooling 3. After adjusting is completed, tighten the
capacity. nut (4).
If the belt is slack, it will slip and vibrate,
shortening its service life and reducing the Replace
air conditioner’s cooling capacity. The belt Replace the belt in the following cases:
should also not be too tense. Adjust the belt ¡ If it stretches and its tension cannot be
tension to the standard value (approximately adjusted.
8 mm or 0.3 in.). ¡ If it is cut or cracked.
¡ If the fan belt is worn and the pulley is
touching the bottom of the V groove.
3
4
L3T016
1
L3T012
211
OPTIONS
Air Conditioner
Removing the filters

Cleaning the Condenser
CAUTION
Cleaning the condenser with high 1
pressured water may damage it. Clean the
condenser gently. 3
1 2
2 4
L3T018
1. Move the seat all the way forward, then

L3T011 fold down the seat back toward the front.
If the condenser is dirty, heat will not 2. Loosen the bolts and remove the cover (1).
discharge properly. Wash dirt off the 3. Loosen the knob and remove the filter
condenser with water. stopper (2).
1. Remove the cover (1) on the right side of 4. Lift the filter (3) upwards and off.
the cab. 5. Remove the filter (4).
2. Clean the condenser (2). 6. Use compressed air or water to clean the
filters, depending on how dirty it is.
Cleaning
CAUTION
Wear safety glasses when using
compressed air.
1. Blow dry, compressed air (138 KPa or 20

Cleaning the Filters psi or less) directly on the filters from the
inside, moving up and down along the
Clean the filters sooner when operating in creases.
dusty places. Be sure to keep the nozzle at an adequate
If the filters are clogged, the air becomes distance from the filters.
weak and a muted booming sound is heard 2. For tough dirt, wash the filter (4) with
from the air conditioner unit. neutral detergent and water. Dry the filter
(4) completely after washing it.
212
OPTIONS
Air Conditioner
Inspecting the Refrigerant (gas) CAUTION

Level
The high pressure pipe becomes hot (80
WARNING to 120°C (176 to 248°F)), so be careful not
to burn yourself when inspecting the
Exposure of the eyes or hands to the refrigerant level.
cooler’s refrigerant could result in
blindness or frostbite. Never touch the
refrigerant or loosen the parts of the 2
cooling circuit.
Should the refrigerant gas leak, keep
flames away.
The cooling capacity will decrease if the

amount of refrigerant is insufficient. 1 L3T017
2 3 4. Also check the temperature of the

compressor’s high pressure pipe (1) and
low pressure pipe (2). Refer to page 214
“Condition of the refrigerant.”
1
L3T014
Off-Season Inspection
Inspect the refrigerant level using the sight
glass (2) on the top of the receiver drier (1). Even off season, run the cooler for 3 to 5
1. Remove the center cover(3). minutes at least once a week to maintain oil
2. Inspect under the following conditions: in the various parts of the compressor.
¡ Cab door ........... Fully open
¡ Temperature control dial
......................... Fully to the COOL side
¡ Air strength ....... High
¡ Airflow mode control dial
......................... Recirculation position
¡ Engine speed .... 1500 rpm
¡ Air conditioner ... On
3. Inspect by watching the flow of air bubbles
in the refrigerant through the sight glass
(2). Refer to page 214 “Condition of the
refrigerant”.
213
OPTIONS
Air Conditioner
Condition of the refrigerant
Sight glass (refrigerant) High/low pressure pipe Pipe connection

temperature
Normal Almost transparent, with High pressure pipe (1) hot No irregularities.
some bubbles, but fully (80 to 120°C (176 to 248°F)),
transparent when the engine low pressure pipe (2) cold
speed is increased or (8 to 15°C (46 to 59°F)).
decreased. Clear difference in
temperature between the
pipes.
Refrigerant Flow of bubbles can be seen High pressure pipe warm, Some oily
low constantly. Refrigerant is low pressure pipe somewhat places.
sometimes transparent or cool. No great difference in
has white bubbles. temperature between the
Refrigerant may be leaking. pipes.
Almost no Some mist-like refrigerant Almost no difference in Some heavily

refrigerant can be barely seen flowing. temperature between the oily places.
Refrigerant has leaked, and high and low pressure pipes.
almost none is left.
Excess No bubbles can be seen, High pressure pipe is hot, No irregularities.

refrigerant even when the fan is set to low pressure pipe is
high and the engine is idling. somewhat cool.
There is a difference in
temperature between the
pipes.
If the air conditioner does not function

If the air conditioner does not cool or heat the air, set the fan switch to OFF and contact a
service outlet for inspection and/or repairs.
IMPORTANT: Continued use of the air conditioner when it is not functioning properly
may damage its various parts.
IMPORTANT: Using the air conditioner when there is no refrigerant will damage the
compressor. Be particularly careful not to do this.
IMPORTANT: Always have a service outlet add or replace the refrigerant. Be sure to
use R134a refrigerant (800g or 1.76 lb).
214
OPTIONS
Throttle Lever
Throttle Lever Decel. Lamp
This controls the engine speed. This lamp lights when decel. button pressed,
(A) .... Low idling the engine speed decreases.
(B) .... Maximum speed
Air Conditioner Outlets Fuse Layout

Fuse Layout and Circuits Protected
15A Horn 10A Deceleration
10A Proportional control 1A Stop solenoid hold

solenoid
20A Lights 10A External power socket
Move the louvers up and down or left and 20A Wiper 10A Cigarette lighter
right to adjust the air flow direction and
amount. 5A Radio 10A Lever lock
5A Heater 10A Automatic-glow
30A Air conditioner 20A Throttle controller

(option) (ACC)
20A Instrument cluster 20A Feed pump
215
OPTIONS
Immobilizer System
Keys
The machine comes with two immobilizer
keys and one registration key. The keys are
used for the immobilizer system (theft
prevention device).
N0B035
Immobilizer key Registration key
The immobilizer system is a device that
protects the machine from theft through the
use of falsified keys, etc. Signals are
exchanged between the machine and the
key, and the engine cannot be started unless
the key is one of the included immobilizer
N0B026E
keys or the registration key. If an attempt is
made to force the engine to start using a ¡ Immobilizer key (key grip: black)
falsified key, an alarm device is activated. The immobilizer key is used not only to
start and stop the engine, but also to lock
Stopping the alarm and unlock the following places:
• Fuel filler cap
• Cab door
• Covers
¡ Registration key (key grip: gray)
The registration key is used for key re-
registration (rewriting the ID code). It can
also be used in the same was as the
immobilizer keys. If an immobilizer key is
N0B036
lost are a new immobilizer key is
Using one of the included immobilizer keys purchased, re-register the keys.
or the registration key, turn the starter switch Refer to page 218 “Re-Registration of the
from OFF (O) to ON ( | ). When the signal is key”.
identified, the alarm stops.
Immobilizer keys can be ordered individually.
If the registration key is lost, however, the
immobilizer system must be replaced. Be
particularly careful not to lose the registration
key, and store it separately from the
immobilizer keys.
216
OPTIONS
Immobilizer System
IMPORTANT: If a key from a different

immobilizer system or a metal object is
brought near or into contact with the
starter switch or key section, the system
may no longer be able to identify the keys’
ID codes, in which case it is no longer
possible to start the engine.
N0B033
• Do not place keys for another

immobilizer system together with your
machine’s keys.
N0B034
• Do not use metal key holders.
217
OPTIONS
Immobilizer System
Registration Procedure
Re-Registration of the Keys
Re-register the keys in the following cases: Immobilizer key Registration key
¡ If one of the immobilizer keys is lost, re-
register the remaining keys so as to
prevent theft.
¡ If you purchase new immobilizer keys,
they must be registered before they can
be used with the machine’s immobilizer N0B026E
system.
¡ The ID code is changed each time a key 1. Prepare the immobilizer keys you wish to
is registered, so any keys you already register (key grip: black/maximum of 5
have must also be re-register. keys) and the registration key (key grip:
Refer to page 216 “Immobilizer System”. gray).
2. Check whether or not the engine starts
IMPORTANT: Please read and understand with the registration key.
the registration procedure before starting. If the engine does not start, it is possible
If you stop in the middle, you may have to that the registration key belongs to another
start over from the beginning. product.
Do not turn the key to the START ( ) This matter must be checked again.
position while performing the steps 3 to
12.
Registration key
N0B029E
3. Insert the registration key into the starter

switch and turn it from the OFF (O) position
to the ON ( I ) position.
4. Hold for about 10 seconds.
218
OPTIONS
Immobilizer System
Registration key Registration key
N0B030E N0B029E
5. Return to the OFF (O) position from the 10. Within 10 seconds after registering the
ON ( I ) position and remove the immobilizer keys, insert the registration
registration key. key into the starter switch and turn it from
the OFF (O) position to the ON ( I )
position.
Immobilizer key 11. Hold for about 10 seconds.
Registration key
N0B027E
6. Within 10 seconds, insert the immobilizer

key into the starter switch and turn it from N0B030E
the OFF (O) position to the ON ( I )
position. 12. Return to the OFF (O) position from the
7. Hold for about 10 seconds. ON ( I ) position and remove the
registration key.
This completes the registration procedure.
Immobilizer key 13. Check that the engine starts using all the
registered keys (registration key and
immobilizer keys).
If the engine does not start, re-register
the keys.
If the engine still does not start, consult a
Takeuchi sales or service outlet.
N0B028E
8. Return to the OFF (O) position from the

ON ( I ) position and remove the
immobilizer key.
9. Perform steps (6) to (8) for all immobilizer
keys (maximum of 5 keys) that you wish
to register.
219
220
INDEX
221
INDEX
A~D
A Boom Lock Valve (2-Piece boom) .............................. 53

Boom Swing Pedal ..................................................... 54
Accessories ................................................................ 54
Accumulator ............................................................. 199
Adjusting the Gap Between the Bucket and Arm ..... 132 C
After Cold Weather is Over ........................................ 87
Cab Door .................................................................... 38
After First 250 Hours (New Machines Only) ............ 119
Caution on refrigerant (gas) ..................................... 204
After First 50 Hours (New Machines Only) .............. 112
Caution on Using the Arm ........................................ 189
After starting the engine ............................................. 15
Cautions ..................................................................... 89
After the Fuel Runs Out ........................................... 145
Cautions after Completing Operations ....................... 87
Air Conditioner ......................................................... 206
Cautions on Maintenance .......................................... 96
Air Conditioner Outlets ............................................. 215
Cautions on Operating ............................................... 80
Air Conditioner Switch .............................................. 208
Cautions on Towing .................................................... 22
Airflow Mode Control Dial ........................................ 209
Cautions on Transporting ........................................... 94
Alway keep the machine clean .................................. 12
Cautions on traveling on slopes ................................. 18
Always clean the machine ......................................... 26
Cautions on Traveling on Slopes ............................... 81
Always maintain good visibility ................................. 206
Cautions on working on the machine ......................... 27
Anti-explosive lighting ................................................ 25
Changing the Link Arm Installation Position ............. 194
Ashtray ....................................................................... 58
Check for safety in the surrounding area before
Attach a “DO NOT OPERATE” tag ............................ 25
starting ................................................................... 16
Attachment Combination Table ................................ 188
Check the position of the undercarriage (tracks)
Avoid battery hazards ................................................ 30
before traveling ...................................................... 17
Avoid fire and explosion hazards ............................... 10
Checks after maintenance ......................................... 31
Cigarette Lighter ........................................................ 58
B Cleaning the air cleaner ........................................... 120
Cleaning the Condenser .......................................... 212
Battery Switch ............................................................ 48 Cleaning the engine cooling system ........................ 124
Be careful not to get crushed or cut ........................... 11 Cleaning the Filters .................................................. 212
Be careful with fluids under pressure ......................... 29 Cleaning the Radiator Fins and Oil Cooler Fins ....... 121
Be careful with hot and pressurized components ...... 28 Clear the area of other persons before starting the
Be careful with hot cooling systems ........................... 28 machine ................................................................. 14
Be sure to lock the safety lock lever before leaving Condition of the refrigerant ...................................... 214
the operator’s seat ................................................. 10 Controls ...................................................................... 35
Before Starting Operation .......................................... 64 Cooling ..................................................................... 209
Before Starting the Engine ......................................... 65
Biodegradable Oil .................................................... 186
Blade Lever ................................................................ 54 D
Bleeding the Air from the Fuel System ..................... 145
222
INDEX
D~I
Daily Inspection .......................................................... 64 First Auxiliary Hydraulic Switches .............................. 50

Daily Inspection (Every 10 Hours) ........................... 107 Fourth Auxiliary Hydraulic Lines ............................... 205
Danger of flying objects ............................................. 22 Fourth Auxiliary Hydraulics ...................................... 204
Decel. Button ............................................................. 49 Front Cover (Tool Box) ............................................... 40
Decel. Lamp ............................................................. 215 Front Window ............................................................. 38
Defogging the Windows ........................................... 210 Fuel and Lubricant Chart ........................................... 98
Disconnect the battery ............................................... 30 Fuel Filler Cap ............................................................ 42
Disposing of wastes ................................................... 31 Fuel Supply Pump .................................................... 198
Do not allow unauthorized personnel in the work area .... 25 Fuse Layout ............................................................. 215
Do not overcool ........................................................ 206
Do not permit riders on the machine .......................... 16
Do not turn the air conditioner on until the engine is G
started ................................................................. 206 General ...................................................................... 96
Doors and Covers ...................................................... 38 General precautions ..................................................... 8
Draining the fuel tank ............................................... 118 General Precautions ................................................ 182
Draining the water separator .................................... 133 Getting Out of Mud ..................................................... 83
E H
Emergency shut-off valve ........................................ 196 Handling asbestos dust .............................................. 11
Engine Hood .............................................................. 41 Handling in Cold Weather .......................................... 87
Ensure good visibility ................................................. 16 Handling of hoses ...................................................... 28
Every 1000 Hours .................................................... 124 Handling of the Accumulator ...................................... 29
Every 2000 Hours .................................................... 127 Handling Rubber Crawlers ......................................... 88
Every 250 Hours ...................................................... 120 Have a Takeuchi service agent repair welding
Every 50 Hours ........................................................ 115 cracks or other damage ......................................... 31
Every 500 Hours ...................................................... 122 Heater ........................................................................ 55
Excavators are not designed for lifting loads ............. 21 Heating and Dehumidifying
Exhaust fumes from the engine can kill ..................... 11 (in cold weather or when the humidity is high) ..... 209
Expendables .............................................................. 99 Horn Button ................................................................ 49
Extending and Retracting the Arm ........................... 189 Hoist the machine safely ............................................ 24
External Power Sockets (for EU) ............................... 57 Hoisting the machine ................................................. 93
Hydraulic Breaker .................................................... 192
Fan Switch ............................................................... 208 I

First Auxiliary Hydraulic Lines .................................... 56 If a Fuse Blows ........................................................ 146
223
INDEX
I~M
If a Warning Lamp Flashes ...................................... 148 Interior Light ............................................................... 57

If the Battery Goes Dead ......................................... 144 Intermediate Boom Operation Indicator Lamp
If the Engine Overheats ........................................... 143 (2-Piece boom) ...................................................... 50
Immobilizer System .................................................. 216 Introduction .................................................................. 2
Important Parts ........................................................ 102
In cold weather ........................................................... 15
Index ........................................................................ 221 K
Indicators ................................................................... 47 Keep a safe distance from electrical power lines ....... 19
Inspecting and Adjusting the Air Conditioner Belt .... 211 Keys ......................................................................... 216
Inspecting and adjusting the engine valve clearance .... 126 Know the working area .............................................. 12
Inspecting and adjusting the fan belt ....................... 114
Inspecting and adjusting the fan belt ....................... 120
Inspecting and Replacing the Fuse .......................... 146 L
Inspecting and replenishing the coolant ................... 107
Let hot air out first .................................................... 206
Inspecting and replenishing the engine oil ............... 108
Lever Pattern (ISO Pattern) ....................................... 68
Inspecting and replenishing the windshield washer
Lever Pattern (JCB Pattern) ....................................... 69
fluid ...................................................................... 133
Levers and Pedals ..................................................... 52
Inspecting by opening the engine hood and covers ...... 105
Lifting Capacities ...................................................... 167
Inspecting by walking around the machine .............. 106
Light Switch ................................................................ 52
Inspecting the battery fluid level and replenishing ... 117
Load and unload the machine safely ......................... 24
Inspecting the crawler tension ................................. 115
Load Safety Device .................................................. 196
Inspecting the engine fuel injection pressure and
Loading and Unloading .............................................. 92
spray condition ..................................................... 126
Long-term Storage ................................................... 140
Inspecting the engine fuel injection timing ............... 129
Lower Front Window .................................................. 39
Inspecting the engine fuel injection valve ................ 129
Lubricating the levers ............................................... 136
Inspecting the fuel level ........................................... 109
Lubricating the slew bearing .................................... 116
Inspecting the Fusible Link ...................................... 147
Lubricating the working equipment ........................... 111
Inspecting the hydraulic oil level and replenishing ... 109
Inspecting the Refrigerant (gas) Level ..................... 213
Inspecting the rubber crawlers ................................. 137 M
Inspecting the water separator ................................. 108
Inspecting while sitting in the operator’s seat .......... 106 Machine Description .................................................... 3
Inspection After Warm-up .......................................... 71 Machine Dimensions ................................................ 158
Inspection and Checks After Stopping the Engine ..... 86 Machine Operation ..................................................... 68
Inspection and Maintenance .................................... 191 Main Specifications .................................................. 156
Instrument cluster ...................................................... 46 Maintain three point contact when mounting and
Insure driver safety before loading trucks .................. 19 dismounting ........................................................... 14
224
INDEX
M~R
Maintenance .............................................................. 95 P
Maintenance Chart ................................................... 103
Maintenance Cover .................................................... 41 Park safely ................................................................. 23
Maintenance Description ........................................... 96 Parking ....................................................................... 86
Maintenance precautions ........................................... 25 Parking the Machine .................................................. 86
Meters ........................................................................ 47 Perform inspection and maintenance daily ................ 13
Mounting and Dismounting ........................................ 64 Place heavy objects in a stable position .................... 27
Power Mode Buttons .................................................. 51
Precautions on Installing Attachments ..................... 182
N Precautions on Operating ........................................ 192
Precautions on Operating Attachments ................... 183
Names of Components .............................................. 36
Precautions on Safety .............................................. 182
Never modify the machine ......................................... 11
Prepare the work area ............................................... 26
Never remove safety equipment .................................. 9
Preparing for Cold Weather ....................................... 87
Never slew (swing) sideways with excessive weights ..... 21
Preparing precautions ................................................ 12
Prohibited Actions ...................................................... 88
O Prohibited Operations ................................................ 78
Provide a fire extinguisher and first aid kit ................... 9
Observe all safety rules ............................................... 8
Off-Season Inspection ............................................. 213
Operate on snow or ice with extra care .................... 18 R
Operating Levers ....................................................... 53
Radio .......................................................................... 59
Operating on slopes is dangerous ............................. 20
Release all pressure before working on the hydraulic
Operating precautions ................................................ 16
system ................................................................... 29
Operating Procedures ................................................ 78
Replace important safety parts periodically ............... 25
Operating Range ...................................................... 162
Replace the hydraulic oil regularly! ............................ 99
Operating the First Auxiliary Hydraulics ..................... 77
Replace the hydraulic oil regularly! .......................... 193
Operating the Machine with Accumulator ................ 199
Replacing the air breather filter ................................ 126
Operating the Travel Levers ....................................... 72
Replacing the air cleaner elements .......................... 125
Operating the Working Equipment ............................. 75
Replacing the bucket ............................................... 134
Operation ................................................................... 63
Replacing the bucket teeth and the side cutters ...... 130
Operations Possible with this Machine ...................... 84
Replacing the engine oil and oil filter ....................... 113
Options ..................................................................... 181
Replacing the engine oil and oil filter ....................... 120
Other Symptoms ...................................................... 150
Replacing the fuel filter ............................................ 122
Outlets ...................................................................... 209
Replacing the hydraulic oil and cleaning the suction
Overload Warning Device ........................................ 197
strainer ................................................................ 127
Replacing the hydraulic oil return filter ..................... 112
225
INDEX
R~T
Replacing the hydraulic oil return filter ..................... 122 Starter Switch ............................................................. 48
Replacing the hydraulic oil with biodegradable oil ... 186 Starting and Stopping the Engine .............................. 65
Replacing the rubber crawlers ................................. 138 Starting precautions ................................................... 14
Replacing the travel motor gear oil .......................... 119 Starting the Engine .................................................... 66
Replacing the travel motor gear oil .......................... 126 Starting with jumper cables ........................................ 15
Replacing the water separator filter ......................... 123 Stay clear of moving parts ......................................... 26
Re-Registration of the Keys ..................................... 218 Stop the engine before performing maintenance ....... 26
Retightening the engine cylinder head bolts ............ 126 Stopping precautions ................................................. 23
Stopping the Engine ................................................... 67
Switches ..................................................................... 48
S Switching the Lever Pattern ..................................... 187
Safety ........................................................................... 7 Switching the Lever Pattern ..................................... 187
Safety Lock Lever ...................................................... 53 Symptoms that are not Malfunctions ........................ 142
Safety signs (Decals) ................................................. 32
Safety Signs (Decals) .............................................. 184
T
Seat ............................................................................ 43
Seat and Seat Belt ..................................................... 43 Telescopic Arm ......................................................... 189
Seat Belt .................................................................... 45 Temperature Control Dial ......................................... 208
Second Auxiliary Hydraulic Lines ............................. 200 Third Auxiliary Hydraulic Lines ................................. 202
Second Auxiliary Hydraulic Switches ....................... 201 Third Auxiliary Hydraulic Switch and Button ............ 203
Second Auxiliary Hydraulics ..................................... 200 Third Auxiliary Hydraulics ......................................... 202
Second / Fourth Auxiliary Hydraulic Switches .......... 205 Third Auxiliary Hydraulics Warning Lamp ................ 203
Secure the engine hood or cover when opened ........ 27 3-Hole Bucket .......................................................... 194
Securely block the machine or any component that Throttle Buttons .......................................................... 51
may fall ................................................................... 27 Throttle Lever ........................................................... 215
Securely block the working equipment ...................... 27 Tightening Torques ................................................... 101
Securing the Machine ................................................ 94 To Lower the Boom .................................................. 152
Selector Button (2-Piece boom) ................................. 49 Tools ......................................................................... 100
Selector Button (2-Piece boom) ............................... 205 Towing ...................................................................... 153
Selector Button (2nd or 4th Aux.) ............................. 204 Transport .................................................................... 91
Service Data .............................................................. 98 Transport the machine safely ..................................... 24
Side Covers ............................................................... 40 Transporting precautions ........................................... 24
Side Window .............................................................. 40 Travel Alarm ............................................................. 195
Slew Speed Switch .................................................... 52 Travel Levers ............................................................. 54
Specifications ........................................................... 155 Travel safety .............................................................. 17
Start the engine from the operator’s seat .................. 14 Travel Speed Switch .................................................. 50
Starter Key ................................................................. 38 Troubleshooting ....................................................... 141
226
INDEX
U~W
Use a signal person and flagman ................................ 9

Use caution when fueling ........................................... 28
Use the correct tools .................................................. 25
Using optional products ............................................. 11
Ventilate periodically ................................................ 206

Vibrations to which the operator is subjected ............ 31
Walk-Around Inspection ............................................. 64

Walk-Around Inspection ........................................... 105
Warming Up the Engine ............................................. 67
Warming Up the Machine (Hydraulic Oil) ................... 70
Warning Lamps .......................................................... 46
Watch boom clearance .............................................. 21
Watch out for hazardous working conditions ............. 20
Wear appropriate clothing and personal protective
equipment ................................................................ 8
When Required ........................................................ 130
Wiper Switch .............................................................. 52
227
First Published May 2000 No. 24129
Seventeenth Published March 2007
OPERATOR’S MANUAL
TB175 Hydraulic Excavator
Edited and issued by TAKEUCHI MFG. CO., LTD.
Printed in Japan by STATION M Co., Ltd.

Takeuchi TB175 Operator's Manual PDF

Uploaded by

Copyright:

Available Formats

Takeuchi TB175 Operator's Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Takeuchi TB175 Operator's Manual PDF

Uploaded by

Copyright:

Available Formats

TB175

Serial No. 17512105~

OPERA TOR’S MANUAL

■ It is the owner or employer’s responsibility to fully instruct each operator in the

Improper operation, inspection and maintenance of this

Downloaded from www.dlmanuals.com

Downloaded from www.dlmanuals.com

DANGER WARNING CAUTION

IMPORTANT: The word “IMPORTANT” is used to alert against operators and

■ EXPLANATION OF GRAPHICAL SYMBOLS

■ Manual storage compartment ■ Serial numbers

1. Open the cover behind the seat. N0A002

■ Front, rear, Ieft and right

Troubleshooting .......................... 141

Specifications .............................. 155

Options ........................................ 181

Index ............................................ 221

Observe all safety rules Wear appropriate clothing and

Provide a fire extinguisher and Use a signal person and flagman

Know and use the hand signals required for

Never remove safety equipment

¡ Know how to use the safety lock lever, seat

Keep flames away from fuel, hydraulic fluid,

Exhaust fumes from the engine Be careful not to get crushed or

Handling asbestos dust Using optional products

Know the working area Alway keep the machine clean

Perform inspection and

Failure to notice or repair machine

Maintain three point contact Clear the area of other persons

Start the engine from the

¡ Fasten the seat belt.

Starting with jumper cables In cold weather

Use jumper cables only in the recommended ¡ Be careful of slippery conditions on

After starting the engine

Ensure good visibility Check for safety in the

¡ Understand the machine limitations.

¡ Do not allow anyone to ride on any part of

¡ Avoid crossing over obstacles whenever

Cautions on traveling on slopes

¡ When traveling on slopes or grades, lower Operate on snow or ice with

Insure driver safety before ¡ Maintain the maximum possible distance

Keep a safe distance from

¡ Be especially careful of buried high voltage

Never approach power lines with any part of

¡ Level off the work area.

¡ Keep machine well back from the edge of

¡ Avoid swinging the loaded bucket in a

¡ Do not approach unstable surfaces (cliffs,

Danger of flying objects Cautions on Towing

When towing, selecting the wrong wire rope,

¡ Park the machine on firm, level ground and

¡ Before leaving the machine, do the

Load and unload the machine Hoist the machine safely

Attach a “DO NOT OPERATE” tag Anti-explosive lighting

Use anti-explosive electrical fixtures and

Do not use damaged or weakened tools or

Replace important safety parts

Prepare the work area Stop the engine before

Always clean the machine Stay clear of moving parts