Scribd
Upload
32 views

Stress-Corrosion Cracking (SCC) : Theory

Stress-corrosion cracking (SCC) is the cracking of a material caused by the combined effect of applied or residual stress and a corrosive environment. SCC can occur in certain alloy-environment-stress combinations and is difficult to detect due to the fine cracks involved. It often results in catastrophic failure with minimal material loss. Effective prevention of SCC includes using appropriate materials, reducing stresses, controlling the environment, and avoiding areas where chemicals can concentrate.

Uploaded by

kitt poung
Copyright
© Public Domain
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
32 views

Stress-Corrosion Cracking (SCC) : Theory

Stress-corrosion cracking (SCC) is the cracking of a material caused by the combined effect of applied or residual stress and a corrosive environment. SCC can occur in certain alloy-environment-stress combinations and is difficult to detect due to the fine cracks involved. It often results in catastrophic failure with minimal material loss. Effective prevention of SCC includes using appropriate materials, reducing stresses, controlling the environment, and avoiding areas where chemicals can concentrate.

Uploaded by

kitt poung
Copyright
© Public Domain
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Yep I wanna test

Stress-Corrosion cracking (SCC)

Theory
SCC is the cracking induced from the combined influence of
tensile stress and a corrosive environment. The impact of SCC on a
material usually falls between dry cracking and the fatigue
threshold of that material. The required tensile stresses may be in the
form of directly applied stresses or in the form of residual stresses, see
an example of SCC of an aircraft component. The problem itself can be
quite complex. The situation with buried pipelines is a good example of
such complexity. The impact is most commonly catastrophic but rarely
as it was for the historical failure of the UK Flixborough chemical reactor
in 1974.

Cold deformation and forming, welding, heat treatment, machining


and grinding can introduce residual stresses. The magnitude and
importance of such stresses is often underestimated. The residual
stresses set up as a result of welding operations tend to approach the
yield strength. The build-up of corrosion products in confined spaces can
also generate significant stresses and should not be overlooked. SCC
usually occurs in certain specific alloy-
environment-stress combinations.

Usually, most of the surface remains


unattacked, but with fine cracks
penetrating into the material. In the microstructure, these cracks can
have an intergranular or a transgranular morphology. Macroscopically,
SCC fractures have a brittle appearance. SCC is classified as a
catastrophic form of corrosion, as the detection of such fine cracks can
be very difficult and the damage not easily predicted. Experimental SCC
data is notorious for a wide range of scatter. A disastrous failure may
occur unexpectedly, with minimal overall material loss.

The micrograph on the right (X500) illustrates intergranular SCC of an


Inconel heat exchanger tube with the crack following the grain
boundaries. (photo courtesy of Metallurgical Technologies)

The micrograph on the left (X300)


illustrates SCC in a 316 stainless steel
chemical processing piping system.Chloride
stress corrosion cracking in austenitic
stainless steel is characterized by the
multi-branched "lightning bolt"
transgranular crack pattern. (photo courtesy
of Metallurgical Technologies)
The most effective means of preventing SCC are: 1) properly with the
right materials; 2) reduce stresses; 3) remove critical environmental
species such as hydroxides, chlorides, and oxygen; 4) and avoid stagnant
areas and crevices in heat exchangers where chloride and hydroxide
might become concentrated. Low alloy steels are less susceptible than
high alloy steels, but they are subject to SCC in water containing chloride
ions.

Chloride SCC

One of the most important forms of stress corrosion that concerns the
nuclear industry is chloride stress corrosion. Chloride stress corrosion is a
type of intergranular corrosion and occurs in austenitic stainless steel
under tensile stress in the presence of oxygen, chloride ions, and high
temperature. It is thought to start with chromium carbide deposits along
grain boundaries that leave the metal open to corrosion. This form of
corrosion is controlled by maintaining low chloride ion and oxygen
content in the environment and use of low carbon steels.

Caustic SCC
Despite the extensive qualification of Inconel for specific applications, a
number of corrosion problems have arisen with Inconel tubing. Improved
resistance to caustic stress corrosion cracking can be given to Inconel by
o o
heat treating it at 620 C to 705 C, depending upon prior solution treating
temperature. Other problems that have been observed with Inconel
include wastage, tube denting, pitting, and intergranular attack.
Prevention
 Avoid the chemical species that causes SCC.
 Control of hardness and stress level (residual or load).
 Introduce compressive stress by shot-peening for example.
 Use of materials known not to crack in the specified environment.
 Control operating temperature and/or the electrochemical
potential of the alloy.

You might also like