Smart Toll Collection System Based On Arduino UNO Controller & ESP8266 Node MCU
Uploaded by
IJRASETPublicationsSmart Toll Collection System Based On Arduino UNO Controller & ESP8266 Node MCU
Uploaded by
IJRASETPublications8 VII July 2020
https://doi.org/10.22214/ijraset.2020.30330
International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.429
Volume 8 Issue VII July 2020- Available at www.ijraset.com
Smart Toll Collection System based on Arduino
UNO Controller & ESP8266 Node MCU
Sahana Patil1, Dr. Baswaraj Gadgay2
1
PG StudentDept. Of VLSI Design & Embedded Systems VTU Centre for PG studies,Kalaburagi, Karnataka, India
2
PG Co-ordinator /Regional Director VTU Centre for PG Studies,Kalaburagi, Karnataka, India
Abstract: the rapid growth in the population has result ns more number of vehicles on the road. The proposed system eliminates
the long of queues of vehicles at the toll plaza by making the collection of toll tax collection automatic. The proposed system is
capable of providing single RFID card for every vehicle and every driver has to swipe the RFID card In front of the RFID reader
present at the toll plaza and automatic deduction of amount will be done from the user available balance. The driver’s total
amount available and deduction amount information will be also sent to registered mobile number and over web server with the
help of GSM and Node MCU ESP8266 module.
Key words: RFID, toll plaza, web server, GSM, Node MCU
I. INTRODUCTION
Fig.1 Toll Plaza
The growing interest of automobile vehicles that assist one to fulfil their day to day activities is emerged out to be new market. The
proposed system in this paper eliminates the long queues of the vehicles at toll plaza by making it fully automatic by utilizing
Arduino UNO controller which is the heart of project, GSM (Global System for Mobile communication) for sending messages,
RFID card and reader modules, servo motor, Buzzer, 16X2 LCD display, LED, Buzzer, Node MCU ESP8266 Wi-Fi module and
L293D motor driver IC. The proposed system provides automation is toll collection system by providing Rechargeable RFID cards
that acts as unique cards for every driver, whenever the driver arrives at the toll plaza he/she has to swipe the respected RFID card in
front of the RFID reader and the required amount at the toll plaza will be automatically deducted by the Arduino UNO processor.
The message of deduction amount and the available amount in the drivers account will be sent over web server with the help of
ESP8266 Node MCU module and to the registered mobile number with the help of GSM module. The proposed system also
incorporates 16X2 LCD, buzzer and on board power supply circuitry.
©IJRASET: All Rights are Reserved 718
International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.429
Volume 8 Issue VII July 2020- Available at www.ijraset.com
II. LITERATURE SURVEY
In [1] the paper provides “Automated Toll Collection System” that provides automation in the collection of toll money with the help
of RFID communication technology and Arduino UNO processor. The proposed system in this paper also consists of android phone
to update the processing information through GSM in the form of message. The proposed system create the opportunity to reduction
improve management and create market for effective intelligence.
In [2] the paper provides “Automatic toll collecting system based on RFID”. The proposed system is prepared with AT89552
microcontroller, RFID tag, RFID reader, 16X2 LCD display, 4X4 keypad, motor driver & DC motor. The proposed system provides
efficient and automatic toll collection system to eliminate the long of queues at the toll plaza.
In [3] the paper provides “Arm7 and Node MCU based Automatic toll collecting system.” The proposed system consists of ARM7
processor and ESP8266 Node MCU Wi-Fi module to provide automation in the collecting processor of toll amount at the toll plaza.
III. PROPOSED DESIGN METHODOLOGY
A. Block Diagram
Fig. 2 Block diagram of proposed system
IV. HARDWARE IMPLEMENTATION
A. The Followings Are The List Of Hardware Components Utilized In The Proposed System
1) Arduino UNO: the Arduino UNO microcontroller board support Atmega328P processor that processes various signals.
2) RFID Module: RFID module consists of RFID reader and RFID tags whose communication can be established with the help of
radio frequencies.
3) Node MCU: The ESP8266 Node MCU module provides IOT platform to various applications.
4) GSM: The proposed system utilizes GSM SIM808 module for sending messages.
5) 16X2 LCD: these acts as small screen to various applications.
6) Buzzer: The electronic sensor which is responsible for generating sound.
7) Servo Motor: The servo motor for converting electrical energy to mechanical energy.
B. The Followings Are The List Of Software Utilized For Designing Proposed System
1) Arduino IDE: The Arduino IDE compiler software is utilized for writing and uploading code to the board.
2) Proteus 8 Professional: This software is utilized for designing of the proposed system.
©IJRASET: All Rights are Reserved 719
International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.429
Volume 8 Issue VII July 2020- Available at www.ijraset.com
V. EXPERIMENTAL SETUP AND RESULT
The following figure provides the experimental setup of the system which is proposed in this paper. The proposed system utilizes
two RFID card i.e. one is valid card and another one is Invalid card. The toll gate will be open when valid card is swiped & it will
remains in closed state upon swiping invalid card. The proposed system in this paper eliminates the long queues of the vehicles at
toll plaza by making it fully automatic by utilizing Arduino UNO controller which is the heart of project, GSM (Global System for
Mobile communication) for sending messages, RFID card and reader modules, servo motor, Buzzer, 16X2 LCD display, LED,
Buzzer, Node MCU ESP8266 Wi-Fi module and L293D motor driver IC. The proposed system provides automation is toll
collection system by providing Rechargeable RFID cards that acts as unique cards for every driver, whenever the driver arrives at
the toll plaza he/she has to swipe the respected RFID card in front of the RFID reader and the required amount at the toll plaza will
be automatically deducted by the Arduino UNO processor. The message of deduction amount and the available amount in the
drivers account will be sent over web server with the help of ESP8266 Node MCU module and to the registered mobile number with
the help of GSM module. The proposed system also incorporates 16X2 LCD, buzzer and on board power supply circuitry.
Fig. 3 Experimental setup of Smart Toll Tax System
The following figures represent the LCD displaying LCD displaying the working of the proposed system
Fig. 4 LCD display Toll TAX Fig. 5 LCD display valid card
©IJRASET: All Rights are Reserved 720
International Journal for Research in Applied Science & Engineering Technology (IJRASET)
ISSN: 2321-9653; IC Value: 45.98; SJ Impact Factor: 7.429
Volume 8 Issue VII July 2020- Available at www.ijraset.com
Fig. 6 LCD display invalid card Fig. 7 LCD display valid card no balance
VI. CONCLUSION
The proposed system totally automated the existing toll system by utilizing the growing technology and also the overall systems
information can also be reported over web server effectively thus eliminates the long queue waiting of vehicles at toll plaza. . The
proposed system provides automation is toll collection system by providing Rechargeable RFID cards that acts as unique cards for
every driver, whenever the driver arrives at the toll plaza he/she has to swipe the respected RFID card in front of the RFID reader
and the required amount at the toll plaza will be automatically deducted by the Arduino UNO processor. The message of deduction
amount and the available amount in the drivers account will be sent over web server with the help of ESP8266 Node MCU module
and to the registered mobile number with the help of GSM module.
REFERENCES
[1] RFID based toll collection system 2011 IEEE third international Conference
[2] ActiveWaveInc. http://www.activewaveinc.com
[3] Smart key Access Control System http://www.smartkey-rfid.com
[4] D. M. Grimes and T. O. Jones, ―Automotive radar: A brief review, Proc. IEEE, vol. 62, no. 6, pp. 804–822, Jun. 1974.
[5] D. M. Grimes and T. O. Jones, ―Automotive radar: A brief review, Proc. IEEE, vol. 62, no. 6, pp. 804–822, Jun. 1974.
[6] Liu Bin, Lu Xiaobo and Gao Chaohui. Comparing and testing of ETC modes in Chinese freeway. ǁ Journal of Transportation Engineering and Information,
5(2), 2007, pp.31-35.
[7] A Novel Chipless RFID System Based on Planar Multiresonators for Barcode Replacement Stevan Preradovic, Isaac Balbin, Nemai C. Karmakar and Gerry
Swiegers2008.
