This document describes a dual operational amplifier and voltage reference integrated circuit. It contains one independent op-amp and a second op-amp whose non-inverting input is wired to a 2.5V voltage reference. Key specifications of the op-amps include low input offset voltage of 0.5mV, low supply current of 350uA, medium bandwidth of 0.9MHz, and large output voltage swing from 0V to VCC - 1.5V. The voltage reference provides a fixed 2.5V output with ±0.4% or ±0.7% precision and can source/sink currents from 1mA to 100mA. The device offers space and cost savings for power supply management and data acquisition applications
This document describes a dual operational amplifier and voltage reference integrated circuit. It contains one independent op-amp and a second op-amp whose non-inverting input is wired to a 2.5V voltage reference. Key specifications of the op-amps include low input offset voltage of 0.5mV, low supply current of 350uA, medium bandwidth of 0.9MHz, and large output voltage swing from 0V to VCC - 1.5V. The voltage reference provides a fixed 2.5V output with ±0.4% or ±0.7% precision and can source/sink currents from 1mA to 100mA. The device offers space and cost savings for power supply management and data acquisition applications
This document describes a dual operational amplifier and voltage reference integrated circuit. It contains one independent op-amp and a second op-amp whose non-inverting input is wired to a 2.5V voltage reference. Key specifications of the op-amps include low input offset voltage of 0.5mV, low supply current of 350uA, medium bandwidth of 0.9MHz, and large output voltage swing from 0V to VCC - 1.5V. The voltage reference provides a fixed 2.5V output with ±0.4% or ±0.7% precision and can source/sink currents from 1mA to 100mA. The device offers space and cost savings for power supply management and data acquisition applications
This document describes a dual operational amplifier and voltage reference integrated circuit. It contains one independent op-amp and a second op-amp whose non-inverting input is wired to a 2.5V voltage reference. Key specifications of the op-amps include low input offset voltage of 0.5mV, low supply current of 350uA, medium bandwidth of 0.9MHz, and large output voltage swing from 0V to VCC - 1.5V. The voltage reference provides a fixed 2.5V output with ±0.4% or ±0.7% precision and can source/sink currents from 1mA to 100mA. The device offers space and cost savings for power supply management and data acquisition applications
OPERATIONAL AMPLIFIER ■ LOW INPUT OFFSET VOLTAGE : 0.5mV typ. ■ LOW SUPPLY CURRENT : 350µA/op. (@ VCC = 5V) ■ MEDIUM BANDWIDTH (unity gain) : 0.9MHz ■ LARGE OUTPUT VOLTAGE SWING : 0V to (VCC - 1.5V) D ■ INPUT COMMON MODE VOLTAGE RANGE SO-8 INCLUDES GROUND (Plastic Micropackage) ■ WIDE POWER SUPPLY RANGE : 3 to 32V ±1.5 TO ±16V ■ 1.5kV ESD PROTECTION ■ VOLTAGE REFERENCE ■ FIXED OUTPUT VOLTAGE REFERENCE PIN CONNECTIONS (top view) 2.5V ■ ±0.4% OR ±0.7% VOLTAGE PRECISION ■ SINK CURRENT CAPABILITY : 1 to 100mA ■ TYPICAL OUTPUT IMPEDANCE : 0.2Ω
DESCRIPTION The TSM103W is a monolithic IC that includes Output 1 1 8 VCC+ OP1 one independent op-amp and another op-amp for OP2 Inverting Input 1 2 7 Output 2 which the non-inverting input is wired to a 2.5V Non-inverting Input 1 3 - + 6 Inverting Input 2 fixed Voltage Reference. This device offers both V - 4 + - space and cost savings in many applications such CC VRef 5 Non-inverting Input 2
as power supply management or data acquisition
systems.
ORDER CODE Temperature Part Number Package Packaging Range TSM103WID Tube TSM103WIDT Tape & Ree -40, +105°C SO-8 TSM103WAID Tube TSM103WAIDT Tape & Reel
April 2004 Revision 3 1/7
TSM103W ABSOLUTE MAXIMUM RATINGS
1 ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit VCC Supply Voltage 36 V Vid Differential Input Voltage Vcc + 0.6 V Vi Input VoltageL -0.3 to Vcc + 0.3V V Tstg Storage temperature range -65 to + 150 °C Ik Continuous cathode current range -100 to 150 mA Tj Maximum Junction Temperature 150 °C Rthja Thermal Resistance Junction to Ambient (SO package) 175 °C/W Tl Maximum Lead Temperature (10 seconds maximum) 260 °C ESD Electrostatic Discharge Protection 1.5 kV
OPERATING CONDITIONS Symbol Parameter Value Unit Vcc DC Supply Conditions 3 to 32 V Ik Vref Cathode Current 1 to 100 mA Toper Operating Free-air Temperature Range -40°C, +105°C °C
2/7 ELECTRICAL CHARACTERISTICS TSM103W
2 ELECTRICAL CHARACTERISTICS Symbol Parameter Min. Typ. Max. Unit Total Supply Current, excluding Current in the Voltage Reference Vcc+ = 5V, no load 0.7 1.2 ICC Tmin. < Tamb < Tmax. mA Vcc+ = 30V, no load 2 Tmin. < Tamb < Tmax
OPERATOR 2 (independent op-amp)
VCC+ = +5V, VCC = Ground, Vo = 1.4V,Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit Input Offset Voltage Vicm = 0V 2 mV TSM103WA, Tamb = 25° 0.5 3 Vio Tmin. ≤ Tamb ≤ Tmax. TSM103W, Tamb = 25° 1 4 Tmin. ≤ Tamb ≤ Tmax. 5 DVio Input Offset Voltage Drift 7 µV/°C Input Offset Current 75 Iio 2 nA Tmin. ≤ Tamb ≤ Tmax. 150 Input Bias Current 20 150 Iib nA Tmin. ≤ Tamb ≤ Tmax 200 Large Signal Voltage Gain Avd VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V 50 100 V/mV Tmin. ≤ Tamb ≤ Tmax. 25 Supply Voltage Rejection Ratio SVR VCC = 5V to 30V 65 100 dB Input Common Mode Voltage Range Vicm VCC = +30V - see note 1 0 (VCC+) -1.5 V Tmin. ≤ Tamb ≤ Tmax. 0 (VCC+) -2 Common Mode Rejection Ratio 70 85 CMR dB Tmin. ≤ Tamb ≤ Tmax. 60 Output Current Source Isource VCC = +15V, Vo = 2V, Vid = +1V 20 40 mA Short Circuit to Ground Io VCC = +15V 40 60 mA Output Current Sink Vid = -1V, Isink VCC = +15V, Vo = 2V 10 20 mA VCC = +15V, Vo = 0.2V 12 50 µA High Level Output Voltage VCC+ = 30V Tamb = 25°C, RL = 2k 26 27 VOH Tmin. ≤ Tamb ≤ Tmax 26 V Tamb = 25°C, RL = 10k 27 28 Tmin. ≤ Tamb ≤ Tmax. 27 Low Level Output Voltage VOL RL = 10k 5 20 mV Tmin. ≤ Tamb ≤ Tmax. 20 Slew Rate at Unity Gain SR Vi = 0.5 to 3V, VCC = 15V 0.2 0.4 V/µs RL = 2k, CL = 100pF, unity gain
3/7 TSM103W ELECTRICAL CHARACTERISTICS
Symbol Parameter Min. Typ. Max. Unit
Gain Bandwidth Product GBP VCC = 30V,RL = 2k, CL = 100pF 0.5 0.9 MHz f = 100kHz, Vin = 10mV Total Harmonic Distortion f = 1kHz THD AV = 20dB,RL = 2k, VCC = 30V 0.02 % CL = 100pF, Vo = 2Vpp Equivalent Input Noise Voltage en f = 1kHz, Rs = 100Ω 50 nV/√Hz Vcc = 30V 1) The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. Both inputs can go to Vcc+ 0.3V without damage.
OPERATOR 1 (op-amp with non-inverting input connected to the internal Vref)
VCC+ = +5V, VCC- = Ground, Tamb = 25°C (unless otherwise specified) Symbol Parameter Min. Typ. Max. Unit Input Offset Voltage Vicm = 0V TSM103WA, Tamb = 25° 2 Vio 0.5 Tmin. ≤ Tamb ≤ Tmax. 3 mV TSM103W, Tamb = 25° 4 1 Tmin. ≤ Tamb ≤ Tmax. 5 DVio Input Offset Voltage Drift 7 µV/°C Input Bias Current Iib negative input 20 nA Large Signal Voltage Gain Avd VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V Tmin. ≤ Tamb ≤ Tmax 100 V/mV Supply Voltage Rejection Ratio SVR Vicm = 0V VCC+ = 5V to 30V 65 100 dB Output Current Source Isource Vo = 2V VCC = +15V, Vid = +1V 20 40 mA Short Circuit to Ground Io VCC = +15V 40 60 mA Output Current Sink Vid = -1V, Isink VCC = +15V, Vo = 2V 10 20 mA VCC = +15V, Vo = 0.2V 12 50 µA High Level Output Voltage VCC+ = 30V Tamb = 25°C, RL = 2k 26 27 VOH Tmin. ≤ Tamb ≤ Tmax. 26 V Tamb = 25°C, RL = 10k 27 Tmin. ≤ Tamb ≤ Tmax. 27 28 Low Level Output Voltage VOL RL = 10k 5 20 mV Tmin. ≤ Tamb ≤ Tmax. 20 Slew Rate at Unity Gain SR Vi = 0.5 to 2V, VCC = 15V 0.2 0.4 V/µs RL = 2k, CL = 100pF, unity gain
4/7 ELECTRICAL CHARACTERISTICS TSM103W
Symbol Parameter Min. Typ. Max. Unit
Gain Bandwidth Product GBP VCC = 30V,RL = 2k, CL = 100pF 0.5 0.9 MHz f = 100kHz, Vin = 10mV Total Harmonic Distortion f = 1kHz THD AV = 20dB,RL = 2k, VCC = 30V 0.02 % CL = 100pF, Vo = 2Vpp
VOLTAGE REFERENCE Symbol Parameter Min. Typ. Max. Unit Reference Input Voltage, Ik=10mA TSM103WA ±0.4% Tamb = 25°C 2.49 2.5 2.51 Vref Tmin. ≤ Tamb ≤ Tmax. 2.48 2.52 V TSM103W ±0.7% Tamb = 25°C 2.482 2.500 2.518 Tmin. ≤ Tamb ≤ Tmax. 2.465 2.535 Reference Input Voltage Deviation Over Temperature Range ∆Vref VKA = Vref; Ik = 10mA Tmin. ≤ Tamb ≤ Tmax. 7 30 mV Minimum Cathode Current for Regulation Imin VKA = Vref 0.5 1 mA Dynamic Impedance - note 1 |ZKA| 0.2 0.5 Ω VKA = Vref, ∆IK = 1 to 100mA, f < 1kHz 1) The dynamic impedance is defined as [ZKA| = ∆VKA/∆IK
5/7 TSM103W ELECTRICAL CHARACTERISTICS
PACKAGE MECHANICAL DATA
SO-8 MECHANICAL DATA
mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX.
A 1.35 1.75 0.053 0.069
A1 0.10 0.25 0.04 0.010
A2 1.10 1.65 0.043 0.065
B 0.33 0.51 0.013 0.020
C 0.19 0.25 0.007 0.010
D 4.80 5.00 0.189 0.197
E 3.80 4.00 0.150 0.157
e 1.27 0.050
H 5.80 6.20 0.228 0.244
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
k 8˚ (max.)
ddd 0.1 0.04
0016023/C
6/7 SUMMARY OF CHANGES TSM103W
3 SUMMARY OF CHANGES Date Revision Description of Changes
1-2 First Release
1 - Vid=Vcc+0.6 modified on AMR table - page 2 2 - Add Ik parameter on AMR table - page 2 02-April-2004 3 3 - Avd test condition equal on both tables Operator 1 & Operator 2 - pages 3 & 4
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
Australia - Belgium - Brazil - Canada - China - Czech Repubic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com
