This document provides details on the one way slab design for a continuous beam and slab structure. It includes:
- Diagrams showing the slab reinforcement layout with main bars and temperature bars.
- Calculations of the factored moments along interior and edge spans based on span lengths and load intensities.
- Distribution of the calculated moments to column, middle, and beam strips using code provided coefficients.
- Determination of required steel areas to resist the calculated moments at various locations along the slab.
The summary provides the key aspects of the one way slab design process including load calculations, moment distribution, and steel reinforcement sizing.
This document provides details on the one way slab design for a continuous beam and slab structure. It includes:
- Diagrams showing the slab reinforcement layout with main bars and temperature bars.
- Calculations of the factored moments along interior and edge spans based on span lengths and load intensities.
- Distribution of the calculated moments to column, middle, and beam strips using code provided coefficients.
- Determination of required steel areas to resist the calculated moments at various locations along the slab.
The summary provides the key aspects of the one way slab design process including load calculations, moment distribution, and steel reinforcement sizing.
This document provides details on the one way slab design for a continuous beam and slab structure. It includes:
- Diagrams showing the slab reinforcement layout with main bars and temperature bars.
- Calculations of the factored moments along interior and edge spans based on span lengths and load intensities.
- Distribution of the calculated moments to column, middle, and beam strips using code provided coefficients.
- Determination of required steel areas to resist the calculated moments at various locations along the slab.
The summary provides the key aspects of the one way slab design process including load calculations, moment distribution, and steel reinforcement sizing.
This document provides details on the one way slab design for a continuous beam and slab structure. It includes:
- Diagrams showing the slab reinforcement layout with main bars and temperature bars.
- Calculations of the factored moments along interior and edge spans based on span lengths and load intensities.
- Distribution of the calculated moments to column, middle, and beam strips using code provided coefficients.
- Determination of required steel areas to resist the calculated moments at various locations along the slab.
The summary provides the key aspects of the one way slab design process including load calculations, moment distribution, and steel reinforcement sizing.
6 SLAB-1 3 f'c = 21 MPa fy = 276 MPa Rebar dia. = 12 mm Slab T = 115 mm cc = 20 mm Ab = 113.10 mm2 rmin = 0.00507 rmax = 0.01883 f = 0.9
SLAB-1 12 mm@ 250 mm O.C. 12 mm@ 490 mm O.C.
Discontinuos Continuos Mid edge edge Mu - 4.42 7.07 b - 1000 1000 d - 89 89 Ru - 0.6199 0.9919 r - 0.00229 0.00370 Use r - 0.00507 0.00507 3m As - 451.45 451.45 N - 4 4 Main Bars s - 250 250 Use s - 250 250 Temperature Bars As - 230 230 s - 490 490 SLAB DESIGN BY DIRECT DESIGN METHOD (Short Span) DL = 1.3 kPa LL = 1.9 kPa Use h = 115 mm Floor weight= gconc x slab T Floor weight= 2.71 kPa Total DL = 4.01 kPa wu = 1.2 DL + 1.6 LL wu = 7.8568 kPa
Using 12 mm diameter bars
d = slab T-.5*bar dia.-cc cc = 20 mm d = 89 mm
Check the depth for shear:
* Beams with a1L2/L1>=1 shall be proportioned to resist shear caused by factored loads on tributary areas bounded by 45 degress lines drawn from the corners of the panels and the center-lines of the adjacent panels parallel to the long sides
a1L2/L1 2.90 >1 check w.b. shear
x = 1.836 m b = 1m Vu = wu * Ashaded Vu = 14.43 kN Vc = 1/6*f'c^.5*b*d x Vc = 67.97 kN 1 L1= 6m f = 0.85 d m strip fVc = 57.78 kN fVc > Vu O.K.
L2= 4.2 m c.s. for wide beam shear
Moment along the short span:
(Note: This is an interior span) Mo = (wuL2)*Ln^2/8 L1= Length of span in direction that moments are being determined measured center to center of supports Ln= Length of clear span in direction that moments are being determined L2= Length of span transverse to L1, measured center to center of supports L1= 4.2 Ln= 3.85 m L1= 4.2 L2= 6m Mo = 87.34 kN-m Negative factored moment= 0.65 x 87.34 Ln Negative factored moment= -56.77 kN-m L2= 6 Positive factored moment= 0.35 x 87.34 Positive factored moment= 30.57 kN-m Distributing these moment to beam and column strips:(Table 10.4) L2/L1 = 1.42857143 a1 = ac = 3.46 a1(L2/L1) = 4.94 (See table 10.4) ===>Interpolated values From Table 10.4 % of Interior negative moment= 69 % Table 10.4 Interior Negative Moment= -39.17 kN-m ===>(Column Strip) According to Section 5.13.6.5 85% will be resisted by beam = -33.29736 kN-m 15% will be resisted by slab = -5.876005 kN-m The remaining is alloted to middle strip = -17.60 kN-m ===>(Middle Strip) (Negative Factored Moment-Interior Negative Moment) % of positive moment= 69 % Table 10.7 Positive Moment= 21.09 kN-m ===>(Column Strip) According to Section 5.13.6.5 85% will be resisted by beam = 17.93 kN-m 15% will be resisted by slab = 3.16 kN-m The remaining is alloted to middle strip = 9.48 kN-m ===>(Middle Strip) (Negative Factored Moment-Interior Negative Moment) Moment along the short span (along edge beam): L1= 5 L2 = 3.175 m Ln = 3.85 m Mo = (wuL2)*Ln^2/8 Mo = 46.22 kN-m Negative factored moment= 0.65 x 46.22 Negative factored moment= -30.04 kN-m Positive factored moment= 0.35 x 46.22 Positive factored moment= 16.18 kN-m For this case, Table 10.5 will be used for distribution of negative moments bt = EcbC 2EcsIs 350 Ecb=Ecs=Ec 150 C = ∑ (1-0.63*x/y)*x^3*y/3 500 Cbeam = 3994520833 Cslab = 287437500 350 C = 4281958333 mm^4 x= 350 x= 150 Is = 843750000 mm^4 y= 500 y= 350 bt = 2.537 L2/L1 = 1.42857143 a1 = aa (for edge beam) a1 = 6.05 a1(L2/L1) = 8.64
SLAB DESIGN BY DIRECT DESIGN METHOD (Long Span) DL = 1.3 kPa LL = 1.9 kPa Use h = 115 mm Floor weight= gconc x slab T Floor weight= 2.71 kPa Total DL = 4.01 kPa wu = 1.2 DL + 1.6 LL wu = 7.8568 kPa
Using 12 mm diameter bars
d = slab T-.5*bar dia.-cc cc = 20 mm d = 89 mm
Check the depth for shear:
* Beams with a1L2/L1>=1 shall be proportioned to resist shear caused by factored loads on tributary areas bounded by 45 degress lines drawn from the corners of the panels and the center-lines of the adjacent panels parallel to the long sides
a1L2/L1 2.90 >1 check w.b. shear
x = 1.836 m b = 1m Vu = wu * Ashaded Vu = 14.43 kN Vc = 1/6*f'c^.5*b*d x Vc = 67.97 kN 1 L1= 6m f = 0.85 d m strip fVc = 57.78 kN fVc > Vu O.K.
L2= 4.2 m c.s. for wide beam shear
Moment along the short span:
(Note: This is an interior span) Mo = (wuL2)*Ln^2/8 L1= Length of span in direction that moments are being determined measured center to center of supports Ln= Length of clear span in direction that moments are being determined L2= Length of span transverse to L1, measured center to center of supports L1= 6 Ln= 5.65 m L2= 4.2 L2= 4.2 m Mo = 131.67 kN-m Int. Negative factored moment= 0.7 x 131.7 Ln Int. Negative factored moment= -92.1722 kN-m L1= 6 Positive factored moment= 0.57 x 131.7 Positive factored moment= 75.05 kN-m Ext. Negative factored moment= 0.16 x 131.7 Ext. Negative factored moment= -21.0679 kN-m
Distributing these moment to beam and column strips:(Table 10.4)
L2/L1 = 0.70 a1 = ab = 4.15 a1(L2/L1) = 2.90 (See table 10.4) ===>Interpolated values From Table 10.4 % of Interior negative moment= 84 % (Table 10.4) (interpolate !) Interior Negative Moment= -77.4 kN-m (Column Strip) According to Section 5.13.6.5 85% will be resisted by beam = -65.8109 kN-m 15% will be resisted by slab = -11.6137 kN-m ===>(Column Strip) The remaining is alloted to middle strip = -14.7476 kN-m ===>(Middle Strip) (Negative Factored Moment-Interior Negative Moment) % of Interior negative moment= 80 % (Table 10.4) Exterior Negative Moment= -16.9 kN-m (Column Strip) According to Section 5.13.6.5 85% will be resisted by beam = -14.3262 kN-m 15% will be resisted by slab = -2.52815 kN-m ===>(Column Strip) The remaining is alloted to middle strip = -4.2 kN-m ===>(Middle Strip) (Negative Factored Moment-Interior Negative Moment) % of positive moment= 84 % (Table 10.7) Positive Moment= 63 kN-m (Column Strip) According to Section 5.13.6.5 85% will be resisted by beam = 53.59 kN-m 15% will be resisted by slab = 9.46 kN-m ===>(Column Strip) The remaining is alloted to middle strip = 12.01 kN-m ===>(Middle Strip)
-1.26 -1.26 -4.2 -1.26 -1.26
4.73 4.73 12.01 4.73 4.73
-5.81 -5.81 -14.75 -5.81 -5.81
SLAB DESIGN BY DIRECT DESIGN METHOD
f'c = 21 MPa fy = 276 MPa Rebar dia. = 12 mm Slab T = 115 mm cc = 20 mm Ab = 113.10 mm2 rmin = 0.00507 rmax = 0.01883 f = 0.9
Column Strip-Left&Right Side Middle Strip
Long Direction Long Direction Discontinuos Continuos Discontinuos Continuos Mid Mid edge edge edge edge Mu 1.26 4.73 5.81 Mu 4.21 12.01 14.75 b 1000 1000 1000 b 1000 1000 1000 d 89 89 89 d 89 89 89 Ru 0.1773 0.6633 0.8146 Ru 0.5911 1.6845 2.0687 r 0.00065 0.00245 0.00302 r 0.00218 0.00642 0.00799 Use r 0.00507 0.00507 0.00507 Use r 0.00507 0.00642 0.00799 As 451.45 451.45 451.45 As 451.45 571.57 710.99 N 4 4 4 N 4 6 7 s 250 250 250 s 250 190 150 Use s 250 250 250 Use s 250 190 150
Short Direction Short Direction Short Direction Discontinuos Continuos Continuos Discontinuos Continuos Continuos Mid Mid Mid edge edge edge edge edge edge Mu 2.80 5.01 - Mu 2.94 1.58 - Mu 20.17 9.75 - b 1000 1000 - b 1000 1000 - b 1000 1000 - d 89 89 - d 89 89 - d 89 89 - Ru 0.3928 0.7034 - Ru 0.4121 0.2219 - Ru 2.8297 1.3681 - r 0.00144 0.00260 - r 0.00151 0.00081 - r 0.01123 0.00516 - Use r 0.00507 0.00507 - Use r 0.00507 0.00507 - Use r 0.01123 0.00516 - As 451.45 451.45 - As 451.45 451.45 - As 999.22 459.51 - N 4 4 - N 4 4 - N 9 5 - s 250 250 - s 250 250 - s 110 240 - Use s 250 250 - Use s 250 250 - Use s 110 240 -
110 mm O.C. L/4
L/4
110 mm O.C.
150 mm O.C.
TOP BAR CONFIGURATION-BOTHWAYS
190 mm O.C. 190 mm O.C.
BOTTOM BAR CONFIGURATION-BOTHWAYS
GRADE BEAM DESIGN GB GB GB GB
GB GB GB GB GB
GB GB GB GB GB
GB
GB GB GB GB
GROUND FLOOR
Design Code: NSCP 2010
ACI318-11 Material & Constants: f'c = 27.6 MPa f = 0.9 fy = 414 MPa fys = 276 MPa ccbot = 40 mm Østirrup = 10 mm b1 = 0.85
At At Moment supports midspan Design Top Bottom Moment 197.113 189.738 Øtop 20 20 Øbottom 20 20 nrebar 5 5 b 300 300 H h 500 500 d 440 440 a 92.40 92.40 300 rmin,1 0.0034 0.0034 rmin,2 0.0136 0.0131 B rmin 0.0034 0.0034 rmax 0.0214 0.0214 ractual 0.0119 0.0119 D/C Ratio 0.86 0.82 Bottom Top nrebar 3 3 Shear Design Vu 283.39 kN at supports at midspan f 0.75 nlegs 4 fVc 88.42 kN Av,min,1 0.35 mm2 Av,min,2 0.38 mm2 Av,min 0.35 mm2 smax 220 mm sreq 887.34 mm s,rest @ 220 mm s@2h 150 mm fVs 254.34 kN 1@50 f(Vc+Vs) 342.76 kN 4 Legs 7 10mmθ @ 150 mm O.C. fVn 342.76 kN 4 Legs Rest @ 200 mm O.C. D/C Ratio 0.827 2F BEAM DESIGN
2FB 2FB 2FB 2FB
2FB 2FB 2FB 2FB 2FB 2FB 2FB 2FB 2FB
2FB 2FB 2FB 2FB 2FB 2FB 2FB 2FB 2FB
2FB 2FB 2FB 2FB
2FB 2FB
2FB 2FB 2FB 2FB
2ND FLOOR FRAME
Design Code: NSCP 2010
ACI318-11 Material & Constants: f'c = 27.6 MPa f = 0.9 fy = 414 MPa fys = 276 MPa ccbot = 40 mm Østirrup = 10 mm b1 = 0.85
At At Moment supports midspan Design Top Bottom Moment 172.109 157.753 Øtop 20 20 Øbottom 20 20 nrebar 5 4 b 300 300 H h 500 500 d 440 440 a 92.40 73.92 300 rmin,1 0.0034 0.0034 rmin,2 0.0118 0.0106 B rmin 0.0034 0.0034 rmax 0.0214 0.0214 ractual 0.0119 0.0095 D/C Ratio 0.75 0.84 Bottom Top nrebar 3 2 Shear Design Vu 271.54 kN at supports at midspan f 0.75 nlegs 4 fVc 88.42 kN Av,min,1 0.35 mm2 Av,min,2 0.38 mm2 Av,min 0.35 mm2 smax 220 mm sreq 887.34 mm s,rest @ 220 mm s@2h 150 mm fVs 254.34 kN 1@50 f(Vc+Vs) 342.76 kN 4 Legs 7 10mmθ @ 150 mm O.C. fVn 342.76 kN 4 Legs Rest @ 200 mm O.C. D/C Ratio 0.792 3F - ROOF BEAM DESIGN
Design Code: NSCP 2010
ACI318-11 Material & Constants: f'c = 27.6 MPa f = 0.9 fy = 414 MPa fys = 276 MPa ccbot = 40 mm Østirrup = 10 mm b1 = 0.85
At At Moment supports midspan Design Top Bottom Moment 142.879 108.883 Øtop 20 20 Øbottom 20 20 nrebar 5 4 b 300 300 H h 500 500 d 440 440 a 92.40 73.92 300 rmin,1 0.0034 0.0034 rmin,2 0.0098 0.0073 B rmin 0.0034 0.0034 rmax 0.0214 0.0214 ractual 0.0119 0.0095 D/C Ratio 0.62 0.58 Bottom Top nrebar 3 2 Shear Design Vu 160.11 kN at supports at midspan f 0.75 nlegs 2 fVc 88.42 kN Av,min,1 0.35 mm2 Av,min,2 0.38 mm2 Av,min 0.35 mm2 smax 220 mm sreq 443.67 mm s,rest @ 220 mm s@2h 150 mm fVs 127.17 kN 1@50 f(Vc+Vs) 215.59 kN 4 Legs 7 10mmθ @ 150 mm O.C. fVn 215.59 kN 4 Legs Rest @ 200 mm O.C. D/C Ratio 0.743
