Scribd
Upload
43 views5 pages

LAB 6 Report: Course Title: Control Systems

The document is a lab report submitted by Tajdar Haider for their Control Systems course. It contains 3 tasks: 1) Find the pole location, rise time, and settling time for systems G(s)=1/(s+1) and G(s)=5/(s+2) 2) Find the output voltage equation, pole location, rise time, and settling time for an RC circuit with R=50Ω and C=5mF 3) Vary the pole location parameter α from 1 to 5 for systems with K=1 and K=5, and observe the effects on step response.

Uploaded by

Tajdar Haider
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
43 views5 pages

LAB 6 Report: Course Title: Control Systems

The document is a lab report submitted by Tajdar Haider for their Control Systems course. It contains 3 tasks: 1) Find the pole location, rise time, and settling time for systems G(s)=1/(s+1) and G(s)=5/(s+2) 2) Find the output voltage equation, pole location, rise time, and settling time for an RC circuit with R=50Ω and C=5mF 3) Vary the pole location parameter α from 1 to 5 for systems with K=1 and K=5, and observe the effects on step response.

Uploaded by

Tajdar Haider
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Page |1

LAB 6 REPORT

COURSE TITLE: CONTROL SYSTEMS

SUBMITTED BY: TAJDAR HAIDER

REG. NO: FA16-EPE-057

SUBMITTED TO: SIR DR. SHAHID MUSTAFA

SUBMISSION DATE: MAY 06, 2019

COMSATS UNIVERSITY ISLAMABAD,


ABBOTTABAD CAMPUS
TASK 1:
Page |2

Find the pole location, rise time and settling time of the following system.
A. G(s)=1/(s+1)
B. G(s)=5/(s+2)
(A)CODE:

num=[1]
den=[1 1];
sys=tf(num,den)
pole(sys)
zero(sys)
pzmap(sys);
legend('pole zero map for system 1/s+1')
figure
step(sys);
grid on
legend('step response for system 1/s+1')
stepinfo(sys)
output
RiseTime: 2.1983
SettlingTime: 3.9124
SettlingMin: 0.9028
SettlingMax: 1.0000
Overshoot: 0
Undershoot: 0
Peak: 1.0000
PeakTime: 10.4907

(B)CODE:
Page |3

clc
clear all;
close all;
num=[5]
den=[1 2];
sys=tf(num,den)
pole(sys)
zero(sys)
pzmap(sys);
legend('pole zero map for system 5/s+2')
figure
step(sys);
grid on
legend('step response for system 5/s+2')
stepinfo(sys)
output
RiseTime: 1.0991
SettlingTime: 1.9562
SettlingMin: 2.2571
SettlingMax: 2.4999
Overshoot: 0
Undershoot: 0
Peak: 2.4999
PeakTime: 5.2453

TASK 2:
Page |4

For the RC circuit given below, find equation for output voltage, pole location, rise time and
settling time when the applied voltage is Vi (t) = step voltage, For the circuit R = 50Ω and C =
5mF.

CODE:

clc
clear all;
close all;
num=[1]
den=[0.25 1];
sys=tf(num,den)
pole(sys)
zero(sys)
pzmap(sys);
legend('pole zero map for system 1/0.25s+1')
figure
step(sys);
grid on
legend('step response for system 1/0.25s+1')
stepinfo(sys)

OUTPUT:

RiseTime: 0.5496
SettlingTime: 0.9781
SettlingMin: 0.9028
SettlingMax: 1.0000
Overshoot: 0
Undershoot: 0
Peak: 1.0000
PeakTime: 2.622

TASK 3:
Page |5

In this task students will study changes occur in angular velocity when location of pole is varied,
where location of pole is dependent on different parameters of the system. Take K=1 and vary α
from 1 to 5 and study the variation in response then take K=5, vary α from 1 to 5 and study the
effect. Use step input and write your observations.

Code:
clc
clear all
close all
k=1;
a=1;
num=[1]
den=[1 1];
sys=tf(num,den)
pole(sys)
zero(sys)
pzmap(sys);
legend('pole zero map for system 1/1s+1')
figure
step(sys);
grid on
legend('step response for system 1/1s+1')
stepinfo(sys)

OUTPUT
RiseTime: 2.1983
SettlingTime: 3.9124
SettlingMin: 4.5141
SettlingMax: 4.9999
Overshoot: 0
Undershoot: 0
Peak: 4.9999
PeakTime: 10.4907

You might also like