20' AUTOLOC SPREADER (N31000C-1PA)

Cage Code: 65059 | Drawing No: SN31000C-1PA | Revision: -- | Sheet: 1 of 2

2" MASTER RING UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
INSIDE DIMENSIONS
14.00 X 7.00
SEE ELECTRONIC PARTS LIST FOR BILL OF MATERIALS
LOCATED 136.5" ABOVE DO NOT SCALE DRAWING
SPREADER CORNER FITTINGS

INDICATOR FLAGS LOCATED AT

EACH CORNER PROVIDE
POSITIVE VISUAL CUE OF LOCKED
OR UNLOCKED SPREADER. FLAGS
ATTACHED DIRECTLY TO BAYONETS

CELL GUIDE WHEELS

FOR EACH CORNER
ARE STANDARD

DETAIL A

TWISTLOCK BAYONET
(SHOWN LOCKED)
DESIGNED FOR TOP
APERATURE IN STANDARD
ISO 1161 CORNER FITTING

NOTES:
1. PART NO.: N31000C-1PA, 20’ AUTOLOC SPREADER
2. SWL 70,528 LB. SEE DETAIL A
3. PROOF TESTED TO 125% (88,160 LB.) AND CERTIFIED
4. STANDARD SPECIFICATION # EAD2100A APPLIES
5. SPREADER MEETS OR EXCEEDS AISC FATIGUE LIFE OF 600,000 CYCLES
6. AUTO ACTUATED SPREADER UNLOCKS WHEN SPREADER IS FIRST LIFTED
THEN LOCKS WHEN LOWERED AND LIFTED AGAIN, ALTERNATING WITH
EACH CYCLE. SHOWN IN LOCKED POSITION
7. FINISH: SANDBLAST, PRIME AND PAINT SAFETY YELLOW
8. CALCULATED WEIGHT: 3,200 LB. SPREADER, SLINGS AND FLIPPER GUIDES
9. DETAILED INFORMATION ON LISTED OPTIONS IS AVAILABLE UPON REQUEST

To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit)
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer,decompile, or take any other action to reproduce or replicate this document or the information
contained herein. © Copyright 2012 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Email: [email protected] • www.tandemloc.com Tandemloc designs, manufactures and tests lifting, securing and mobilizing components for all
824 Highway 101 • Havelock, NC 28532 industries. See our website for details and important safety information.
TEL: 1.800.258.7324 (252.447.7155) Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
FAX: 1.800.892.3273 (252.447.5502)
 20' AUTOLOC SPREADER (N31000C-1PA)
Cage Code: 65059 | Drawing No: SN31000C-1PA | Revision: -- | Sheet: 2 of 2
UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
SEE ELECTRONIC PARTS LIST FOR BILL OF MATERIALS
236.94 FRAME OVERALL DO NOT SCALE DRAWING

NOTES:
1. PART NO.: N31000C-1PA, 20’ AUTOLOC SPREADER
95.47 2. OUTSIDE DIMENSIONS OF SPREADER (LENGTH AND WIDTH)
FRAME ARE LESS THAN OUTSIDE DIMENSIONS OF LIFTED CONTAINER
OVERALL

FLIPPER GUIDE SHOWN

IN RETRACTED POSITION

28.81
FLIPPER GUIDE
FRAME OVERALL
SHOWN IN USE POSITION

AUTOLOC VINYL
BOTH SIDES
60.83

WLL 70,528 LB
5” RED VINYL 5” BLACK VINYL
BOTH SIDES BOTH SIDES

88.97
BAYONET CENTER
38.03 TO BAYONET CENTER
17.95
230.44 BAYONET CENTER TO BAYONET CENTER
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit)
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer,decompile, or take any other action to reproduce or replicate this document or the information
contained herein. © Copyright 2012 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Email: [email protected] • www.tandemloc.com Tandemloc designs, manufactures and tests lifting, securing and mobilizing components for all
824 Highway 101 • Havelock, NC 28532 industries. See our website for details and important safety information.
TEL: 1.800.258.7324 (252.447.7155) Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
FAX: 1.800.892.3273 (252.447.5502)
 REVISIONS
REV DESCRIPTION DATE APPROVED ®
A REMOVED “OPTIONAL” FROM FLIPPER GUIDE NOTES 1/27/10 DAH 40' AUTOLOC SPREADER (N3100AA-2PA)
Cage Code: 65059 | Drawing No: SN3100AA-2PA | Revision: A | Sheet: 1 of 2
UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
2" MASTER RING SEE ELECTRONIC PARTS LIST FOR BILL OF MATERIALS
INSIDE DIMENSIONS 14.00 [356 MM] X 7.00 [178 MM] DO NOT SCALE DRAWING
LOCATED 256.5" [6515 MM]
INDICATOR FLAGS LOCATED AT
ABOVE SPREADER CORNER FITTINGS
EACH CORNER PROVIDE
POSITIVE VISUAL CUE OF LOCKED CELL GUIDE WHEELS
OR UNLOCKED SPREADER. FLAGS FOR EACH CORNER
ATTACHED DIRECTLY TO BAYONETS ARE STANDARD

FLIPPER GUIDE
TYPICAL 4 PLACES

AUTOLOC® GEAR BOX ACTIVATES

DRIVE LINKAGE & ROTATES TWISTLOCK
BAYONETS. ALTERNATES BETWEEN
LOCKED & UNLOCKED EACH TIME THE
SLING IS SLACKENED FROM A FULLY DETAIL A
TENSIONED POSITION

TWISTLOCK BAYONET
(SHOWN LOCKED)
DESIGNED FOR TOP
APERATURE IN STANDARD
ISO 1161 CORNER FITTING

NOTES:
1. PART NO.: SN3100AA-2PA, 40' AUTOLOC® SPREADER
2. SWL 67,200 LB SEE DETAIL A
3. PROOF TESTED TO 125% (84,000 LB) AND CERTIFIED
4. STANDARD SPECIFICATION #EAD2100A APPLIES
5. SPREADER MEETS OR EXCEEDS AISC FATIGUE LIFE OF 600,000 CYCLES
6. AUTO ACTUATED SPREADER UNLOCKS WHEN SPREADER IS FIRST LIFTED THEN
LOCKS WHEN LOWERED AND LIFTED AGAIN, ALTERNATING WITH EACH CYCLE. SHOWN
IN LOCKED POSITION.
7. FINISH: SANDBLAST, THERMAL ZINC, PRIME AND PAINT SAFETY YELLOW
8. CALCULATED WEIGHT: 4,000 LBS
9. DETAILED INFORMATION ON LISTED OPTIONS IS AVAILABLE UPON REQUEST
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit)
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer,decompile, or take any other action to reproduce or replicate this document or the information
contained herein. © Copyright 2012 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Email: [email protected] • www.tandemloc.com Tandemloc designs, manufactures and tests lifting, securing and mobilizing components for all
824 Highway 101 • Havelock, NC 28532 industries. See our website for details and important safety information.
TEL: 1.800.258.7324 (252.447.7155) Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
FAX: 1.800.892.3273 (252.447.5502)
 NOTES: ®
1. PART NO.: SN3100AA-2PA, 40' AUTOLOC® SPREADER 40' AUTOLOC SPREADER (N3100AA-2PA)
2. OUTSIDE DIMENSIONS OF SPREADER (LENGTH AND WIDTH)
ARE LESS THAN OUTSIDE DIMENSIONS OF LIFTED CONTAINER
Cage Code: 65059 | Drawing No: SN3100AA-2PA | Revision: A | Sheet: 1 of 2
UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
SEE ELECTRONIC PARTS LIST FOR BILL OF MATERIALS
478.38 [12,151mm] FRAME OVERALL DO NOT SCALE DRAWING

21.37
26.36 [543mm]
83.76 103.81 103.23 103.81 83.76
[670mm] [2,128mm] [2,637mm] [2,622mm] [2,637mm] [2,128mm]

95.47 2.60 [66mm] TYP

81.97 [2,082mm]
[2425mm]
FRAME
OVERALL
6.00 [152mm]

26.36
[670mm] 48.88 [1,242mm] 48.88 [1,242mm]

6.00 [152mm]
21.38
[543mm] REVISIONS
REV DESCRIPTION DATE APPROVED
FLIPPER GUIDE A REMOVED “OPTIONAL” FROM FLIPPER GUIDE NOTES 1/27/10 DAH
SHOWN IN USE POSITION

28.81 [731.8mm]
FRAME OVERALL
60.83
[1545mm] FLIPPER GUIDE SHOWN 11.78 [299mm]
IN RETRACTED POSITION
38.05
[966.3mm]

10.00
[254mm] 17.95
[456mm] 7.03
[179mm]
88.97 [2260mm]
BAYONET CENTER
TO BAYONET CENTER
471.88 [11986mm] BAYONET CENTER TO BAYONET CENTER
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit)
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not, and shall not encourage, assist, or authorize another party to copy, distribute, publically display, modify, reverse engineer,decompile, or take any other action to reproduce or replicate this document or the information
contained herein. © Copyright 2012 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Email: [email protected] • www.tandemloc.com Tandemloc designs, manufactures and tests lifting, securing and mobilizing components for all
824 Highway 101 • Havelock, NC 28532 industries. See our website for details and important safety information.
TEL: 1.800.258.7324 (252.447.7155) Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
FAX: 1.800.892.3273 (252.447.5502)