Scribd Logo
Upload

Welcome to Scribd!

  • 41 views

    Product Instructions Calibration Procedure For Delta4310/4110

    Uploaded by

    Marco C. Puma
    This document provides instructions for calibrating the Delta4310/4110 product in 3 steps. Step A calibrates just the control unit using a calibration box. Step B connects the control unit and HV unit to calibrate at higher voltages. Step C takes final readings from the capacitor standard to verify the calibration. The process requires specialized equipment and takes approximately 30 minutes per unit. Proper grounding and safety precautions should be followed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Product Instructions Calibration Procedure For Delta4310/4110

    Uploaded by

    Marco C. Puma
    41 views2 pages
    This document provides instructions for calibrating the Delta4310/4110 product in 3 steps. Step A calibrates just the control unit using a calibration box. Step B connects the control unit and HV unit to calibrate at higher voltages. Step C takes final readings from the capacitor standard to verify the calibration. The process requires specialized equipment and takes approximately 30 minutes per unit. Proper grounding and safety precautions should be followed.

    Original Title

    DELTA4xxxCalibrationProcedure(r1)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for calibrating the Delta4310/4110 product in 3 steps. Step A calibrates just the control unit using a calibration box. Step B connects the control unit and HV unit to calibrate at higher voltages. Step C takes final readings from the capacitor standard to verify the calibration. The process requires specialized equipment and takes approximately 30 minutes per unit. Proper grounding and safety precautions should be followed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    41 views2 pages

    Product Instructions Calibration Procedure For Delta4310/4110

    Uploaded by

    Marco C. Puma
    This document provides instructions for calibrating the Delta4310/4110 product in 3 steps. Step A calibrates just the control unit using a calibration box. Step B connects the control unit and HV unit to calibrate at higher voltages. Step C takes final readings from the capacitor standard to verify the calibration. The process requires specialized equipment and takes approximately 30 minutes per unit. Proper grounding and safety precautions should be followed.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    June 27, 2012

    Product Instructions
    Calibration Procedure for Delta4310/4110

    Required Equipment and recommendations

    • Calibrated Precision Multi-Meter.


    • Calibrated CAL4000 calibration box.
    • A Computer with all Software loaded from the supplied CD.
    • Field Calibrator Standard p/n 670500-1 or equivalent.
    • Process takes approximately 25~30 minutes per Control Unit.
    • Make sure Firmware and Software are up to date and are installed prior to Calibration and Test.
    • Make sure that all HV precautions are observed.

    Step A) -Calibration – Control Unit only


    (In this step, only the control unit is connected the calibration Box)
     Connect the instrument Test Ground Cable to the building ground
     Connect the instrument Mains Connector to a grounded outlet
     Connect the two instrument Interlock Cheater Plugs
     Connect the Red Measurement Cable to the instrument (make that this cable is not coiled)
     Connect the unit to the PC using a USB cable (calibration can only be performed via USB)
     Connect the CAL4000 Calibration Box to the Control Unit using the HV Power Cable (p/n:
    2002-132) and HV Control Cable (p/n: 2002-133)
    o Turn on Control Unit
    o Start MIX software, then select Maintenance Tab.
    o You will need to re-start MIX software if you have just used it to program firmware.
    o Press CTL-ALT-SHIFT-S on keyboard to enter “MAINTENANCE (SERVICE) MODE”.
    o Under Calibration Menu pull-down check all tests except last 2 boxes (The last 2 tests (D190 and D200) will
    require the HV unit in Step B)
    o Click START CALIBRATION button
    o Follow on-screen instructions for setup connections  Enter DVM voltage measurements (in DC volts) as
    required
    Note: First shunt in calibration process, 10Ω, may possibly give an error message indicating Inverter has
    tripped. Click the Retry button to go again. Now, the program should continue process.
    Some of the steps may take several minutes.
    o Click “Save Calibration Results” button when prompted.

    http://www.megger.com
    Valley Forge Corporate Center
    2621 Van Buren Ave
    Norristown, PA 19403-2329 USA Page 1 of 2
    1-800-723-2861 PN: 82412 Rev. 1
    June 27, 2012
    Product Instructions
    Calibration Procedure for Delta4310/4110

    Step B)-HV Unit Calibration

    (In this step, the Control Unit and the HV are inter-connected, and the HV voltage is connected to 100PF
    standard)
    o Turn on Control Unit
    o Start MIX software, then select Maintenance tab.
    o You will need to re-start MIX software if you have just used it to program firmware.
    o Press CTL-ALT-SHIFT-S on keyboard to enter “MAINTENANCE (SERVICE) MODE”.
    o choose Calibration tab, and in Calibration Tasks window select only D190 and D200 ( All others must be
    deselected).
    Note: Before commencing calibration, ensure that the Delta4000 is setup correctly as follows: Low
    Voltage Red cables is and HV cable are connected from the Delta4000 units to the certified 100 pF
    standard, the two Interlocks are installed, short ground wire is installed between the two unit’s wing
    nut grounds, Main Test Ground cable connected between earth ground and Test ground connector on
    Control Unit, Connect HV Power and HV Control cables between the two Units, and supplied USB from
    PC to Control Unit.
    o Click “Start Calibration” button .
    o Follow instructions on the computer (Mix software).
    o Select save to instrument at the end of procedure.
    o End of Procedure

    Step C)-Final Test the unit to verify the calibration process :

    Use PowerDB or the Delta control software to take multiple readings in different modes of the Capacitor
    Standard used to verify the unit accuracy.

    http://www.megger.com
    Valley Forge Corporate Center
    2621 Van Buren Ave
    Norristown, PA 19403-2329 USA Page 2 of 2
    1-800-723-2861 PN: 82412 Rev. 1

    You might also like