IDTQS3VH16233

2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

QUICKSWITCH® PRODUCTS IDTQS3VH16233

2.5V / 3.3V 32:16 MUX/DEMUX
HIGH BANDWIDTH BUS SWITCH

FEATURES: DESCRIPTION:
• N channel FET switches with no parasitic diode to Vcc The QS3VH16233 HotSwitch is a 32-bit to 16-bit high bandwidth bus
− Isolation under power-off conditions switch, which can multiplex or demultiplex data. The QS3VH16233 has
− No DC path to Vcc or GND very low ON resistance, resulting in under 250ps propagation delay
− 5V tolerant in OFF and ON state through the switch. This device can be used as two 16-bit to 8-bit
• 5V tolerant I/Os multiplexers or as one 32-bit to 16-bit multiplexer. SELx inputs control the
• Low RON - 4Ω Ω typical data flow. TESTx inputs control either one or two ports connection. In the
• Flat RON characteristics over operating range OFF and ON states, the switches are 5V-tolerant. In the OFF state, the
• Rail-to-rail switching 0 - 5V switches offer very high impedance at the terminals.
• Bidirectional dataflow with near-zero delay: no added ground The combination of near-zero propagation delay, high OFF impedance,
bounce and over-voltage tolerance also makes the QS3VH16233 ideal for high
• Excellent RON matching between channels performance communications applications.
• Vcc operation: 2.3V to 3.6V The QS3VH16233 is characterized for operation from -40°C to +85°C.
• High bandwidth - up to 500 MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in TSSOP package

APPLICATIONS:
• Hot-swapping
• 10/100 Base-T, Ethernet LAN switch
• Low distortion analog switch
• Replaces mechanical relay
• ATM 25/155 switching

FUNCTIONAL BLOCK DIAGRAM

TEST1 TEST2

SEL1 x = 1 through 8 SEL2 x = 9 through 16

xB2 xB2
xA xA
xB1 xB1
ONE OF EIGHT CHANNELS ONE OF EIGHT CHANNELS

The IDT logo is a registered trademark of Integrated Device Technology, Inc.

INDUSTRIAL TEMPERATURE RANGE FEBRUARY 2013

1
c 2013 Integrated Device Technology, Inc. DSC-5882/9
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS(1)

Symbol Description Max. Unit
1A 1 56 1B1 VTERM(2) Supply Voltage to Ground – 0.5 to 4.6 V

2B1 2 55 1B2
VTERM(3) DC Switch Voltage VS – 0.5 to 5.5 V
VTERM(3) DC Input Voltage VIN – 0.5 to 5.5 V
2B2 3 54 2A
VAC AC Input Voltage (pulse width ≤20ns) –3 V
3A 4 53 3B1
IOUT DC Output Current (max. current/pin) 120 mA
4B1 5 52 3B2
TSTG Storage Temperature -65 to +150 °C
4B2 6 51 4A NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
5A 7 50 5B1 cause permanent damage to the device. This is a stress rating only and functional
6B1 8 49 5B2 operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
6B2 9 48 6A maximum rating conditions for extended periods may affect reliability.
2. VCC terminals.
7A 10 47 7B1 3. All terminals except VCC.
8B1 11 46 7B2

8B2 12 45 8A

GND 13 44 GND CAPACITANCE o

(TA = +25 C, f = 1MHz, VIN = 0V, VOUT = 0V)
Symbol Parameter(1) Typ. Max. Unit
Vcc 14 43 Vcc
CIN Control Inputs 3 5 pF
9A 15 42 9B1
CI/O Quickswitch Channels Mux 8 12 pF
10B1 16 41 9B2
(Switch OFF) Demux 4 6
10B2 17 40 10A
CI/O Quickswitch Channels Mux 16 24 pF
11A 18 39 11B1
(Switch ON) Demux 8 12
12B1 19 38 11B2 NOTE:
12B2 20 37 12A
1. This parameter is guaranteed but not production tested.

13A 21 36 13B1

14B1 22 35 13B2

PIN DESCRIPTION
14B2 23 34 14A

15A 24 33 15B1
Pin Names I/O Description
16B1 25 32 15B2
xA I/O Bus A
16B2 26 31 16A xBx I/O Bus B
TEST1 27 30 SEL1 SELx I Data Select
TEST2 28 29 SEL2 TESTx I Port Select

TSSOP
TOP VIEW FUNCTION TABLE(1)
SELx TESTx xA Function
L L xB 1 xA to xB1
H L xB 2 xA to xB2
X H xB1, xB2 xA to xB1 and xB2
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care

2
 IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE(1)

Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 3.3V ± 0.3V
Symbol Parameter Test Conditions Min. Typ.(1) Max. Unit
VIH Input HIGH Voltage Guaranteed Logic HIGH VCC = 2.3V to 2.7V 1.7 — — V
for Control Inputs VCC = 2.7V to 3.6V 2 — —
VIL Input LOW Voltage Guaranteed Logic HIGH VCC = 2.3V to 2.7V — — 0.7 V
for Control Inputs VCC = 2.7V to 3.6V — — 0.8
IIN Input Leakage Current (Control Inputs) 0V ≤ VIN≤ VCC — — ±1 μA
I OZ Off-State Current (Hi-Z) 0V ≤ VOUT ≤ 5V, Switches OFF — — ±1 μA
IOFF Data Input/Output Power Off Leakage VIN or VOUT 0V to 5V, VCC = 0V — — ±1 μA
VCC = 2.3V VIN = 0V ION = 30mA — 6 8
RON Switch ON Resistance (Typ. at VCC = 2.5V) VIN = 1.7V ION = 15mA — 7 9 Ω
VCC = 3V VIN = 0V ION = 30mA — 4 6
VIN = 2.4V ION = 15mA — 5 8
NOTE:
1. Typical values are at VCC = 3.3V and TA = 25°C, unless otherwise noted.

TYPICAL ON RESISTANCE vs VIN AT VCC = 3.3V

16

R ON 14
(ohms) 12
10
8
6
4
2
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0

V IN
(Volts)

3
 IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

POWER SUPPLY CHARACTERISTICS

Symbol Parameter Test Conditions(1) Min. Typ. Max. Unit
ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or VCC, f = 0 — 1.5 3 mA
ΔICC Power Supply Current (2,3)
per Input HIGH VCC = Max., VIN = 3V, f = 0 per Control Input — — 30 μA
ICCD Dynamic Power Supply Current(4) VCC = 3.3V, A and B Pins Open, Control Inputs See Typical ICCD vs Enable Frequency graph below
Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. A and B pins do not contribute to ΔIcc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and B inputs do not contribute to the Dynamic Power Supply
Current. This parameter is guaranteed but not production tested.

TYPICAL ICCD vs ENABLE FREQUENCY CURVE AT VCC = 3.3V

20

18

16

14

12
ICCD (mA)

10

0
0 2 4 6 8 10 12 14 16 18 20

ENABLE FREQUENCY (MHz)

4
 IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

SWITCHING CHARACTERISTICS OVER OPERATING RANGE

TA = -40°C to +85°C
VCC = 2.5 ± 0.2V (1) VCC = 3.3 ± 0.3V (1)
Symbol Parameter Min. (4) Max. Min. (4) Max. Unit
tPLH Data Propagation Delay(2,3) ⎯ 0.2 ⎯ 0.2 ns
tPHL A to B or B to A
tBX Switch Multiplex Delay 1.5 9 1.5 7.5 ns
SEL to xA
tPZH Switch Turn-On Delay 1.5 9 1.5 8 ns
tPZL SEL to xBx
tPHZ Switch Turn-Off Delay 1.5 7.5 1.5 7.5 ns
tPLZ SEL to xBx
tPZH Switch Turn-On Delay 1.5 8.5 1.5 9 ns
tPZL TEST to xBx
tPHZ Switch Turn-Off Delay 1.5 8.5 1.5 8.5 ns
tPLZ TEST to xBx
fSx Operating Frequency - Enable (2,5) ⎯ 7.5 ⎯ 15 MHz
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.2ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4. Minimums are guaranteed but not production tested.
5. Maximum toggle frequency for Sx control input (pass voltage > VCC, VIN = 5V, RLOAD > 1MΩ, no CLOAD).

5
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

SOME APPLICATIONS FOR HOTSWITCH PRODUCTS

NFET
0 to +5V 0 to +5V

Vcc = 3.3V CHARGE PUMP +6.5V

OE DRIVER

SINGLE HOT
SWITCH

Rail-to-Rail Switching

PHY

3VH
4.5VPP SWITCH

LOGIC 10Mbps to 100Mbps Z = 100 W LOGIC

Z = 100 W
SIDE >100m SIDE
4.5VPP TWISTED PAIR 2VPP

Fast Ethernet Data Switching (LAN Switch)

PLUGGABLE CARD/ LIVE SYSTEM ZERO DOWN TIME SYSTEM

CONNECTOR

QS3VHXXX

ON CARD
CARD I/O CPU
LOGIC
CONNECTOR

QS3VHXXX

ON CARD
CARD I/O RAM
LOGIC

Hot Swapping BUS

6
 IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

TEST CIRCUITS AND WAVEFORMS

TEST CONDITIONS
VIH
Symbol VCC(1)= 3.3V ± 0.3V VCC(2)= 2.5V ± 0.2V Unit SAME PHASE VT
VLOAD 6 2 x Vcc V INPUT TRANSITION 0V
tPLH tPHL
VIH 3 Vcc V OUTPUT VOH
VT
VT 1.5 VCC/2 V VOL
VLZ 300 150 mV tPLH tPHL
OPPOSITE PHASE VIH
VHZ 300 150 mV INPUT TRANSITION VT
0V
CL 50 30 pF
Propagation Delay

VLOAD
VCC ENABLE DISABLE
Open VIH
CONTROL VT
500Ω GND INPUT
tPZL 0V
VIN tPLZ
(1, 2) VOUT
Pulse VLOAD/2
D.U.T. OUTPUT VLOAD/2
Generator SWITCH
NORMALLY CLOSED VT VOL + VLZ
500Ω LOW VOL
RT tPZH tPHZ
CL
OUTPUT SWITCH VOH
NORMALLY VT VOH -VHZ
OPEN
Test Circuits for All Outputs HIGH 0V 0V
NOTE:
DEFINITIONS: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
Enable and Disable Times
NOTES:
1. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2ns; tR ≤ 2ns.

SWITCH POSITION
Test Switch
tPLZ/tPZL VLOAD
tPHZ/tPZH GND
tPD Open

7
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE

ORDERING INFORMATION
QS XXXXX XX X
Device Type Package

Blank Tube or Tray

8 Tape and Reel

PAG Thin Shrink Small Outline Package - TSSOP Green

3VH16233 2.5V / 3.3V 32:16 Mux / Demux High Bandwidth Switch

Datasheet Document History

02/15/13 Pg. 1, 8 Updated the Ordering Information by removing non green package version, the “IDT” notation and
Adding Tape and Reel information.

CORPORATE HEADQUARTERS for SALES: for Tech Support:

6024 Silver Creek Valley Road 800-345-7015 or 408-284-8200 [email protected]
San Jose, CA 95138 fax: 408-284-2775
www.idt.com