Scribd Logo
Upload

Welcome to Scribd!

  • 122 views

    Tips Hyper Works

    Uploaded by

    mahdirahmanifacebook
    Beginning with OptiStruct 7.0, a non-linear solution sequence is available for modeling contact problems. Gap elements (CGAP) are defined node-to-node and require a property card and an orientation vector to be assigned to them. Gap element behavior is defined through the PGAP property card.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Tips Hyper Works

    Uploaded by

    mahdirahmanifacebook
    122 views2 pages
    Beginning with OptiStruct 7.0, a non-linear solution sequence is available for modeling contact problems. Gap elements (CGAP) are defined node-to-node and require a property card and an orientation vector to be assigned to them. Gap element behavior is defined through the PGAP property card.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Beginning with OptiStruct 7.0, a non-linear solution sequence is available for modeling contact problems. Gap elements (CGAP) are defined node-to-node and require a property card and an orientation vector to be assigned to them. Gap element behavior is defined through the PGAP property card.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    122 views2 pages

    Tips Hyper Works

    Uploaded by

    mahdirahmanifacebook
    Beginning with OptiStruct 7.0, a non-linear solution sequence is available for modeling contact problems. Gap elements (CGAP) are defined node-to-node and require a property card and an orientation vector to be assigned to them. Gap element behavior is defined through the PGAP property card.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    HyperWorks Tip/Trick 652

    Applications:
    OptiStruct

    Application version:
    OptiStruct 7.0 or higher

    Computer hardware:
    All supported

    Computer operating systems:


    All supported

    Categories: Subcategories
    Analysis: Setup and Theory

    Topic:
    Nonlinear (iterative) solutions using gap elements

    Topic details:
    Beginning with OptiStruct 7.0, a non-linear solution sequence is available for modeling contact problems.
    Any model with non-linear CGAP (gap) elements uses the non-linear solution sequence. The element can
    be used for both static analysis and optimization; however, the assumptions of small displacement and
    small strain still apply.

    Figure 1: Model with gap elements

    Altair Engineering © 2005 Page 1

    Proprietary Information of Altair Engineering.


    Gap elements (CGAP) are defined node-to-node and require a property card and an orientation vector to
    be assigned to them. Gap element behavior is defined through the PGAP property card. Before creating a
    gap element, it is recommended that you create the PGAP property card. You can assign the property to
    the gap elements when you create them through the gaps panel (or other panels) in HyperMesh. Most of
    the panels that create 1-D elements (for example linear 1-D) can also be used to create gap elements by
    changing element configurations.
    On the PGAP card, the initial gap opening is defined by U0. The gap element offers very low stiffness
    until the gap is closed. Friction can also be specified, and gets activated once the gap is closed. For more
    details on U0 and PGAP, please see the OptiStruct online help for PGAP. (You can go to the Index tab
    of the online help and type in PGAP).

    Orientation vector for the gap element


    Similar to BAR, BEAM, and other 1-D elements, an element coordinate system has to be defined for
    CGAP elements. Gap element coordinate systems can be established by defining either a coordinate
    system or an orientation vector. For more details, please consult the online help for CGAP.

    Note: Gap elements can also be created with the no vector option (in HyperMesh) in which no
    orientation is specified for the gap element. In such a case, the line joining the first node and the
    second node will be taken as the element X-axis. Again, consult the online help for details.

    Activating nonlinear solution (NLPARM)


    OptiStruct uses its linear solution sequence by default even if gap elements are present. A non-linear
    solution is activated for a subcase by including the NLPARM parameter. If NLPARM is not present in the
    subcase definition, the gap element has linear behavior. In this situation, the gap status is determined
    once at the beginning of the solution, and does not change as the solution progresses.
    In HyperMesh, the NLPARM parameter can be defined by creating a load collector with card image
    “NLPARM.” The NINC parameter on this card represents the number of equal subdivisions that the total
    load in a given subcase will be divided into. If NINC is blank, the entire load for a given subcase is applied
    at once. In most cases, this is the only parameter that needs to be defined. This NLPARM load collector
    needs to be included for the subcase along with static loads and SPCs. Please refer to the Nonlinear
    Gap Analysis section of the online help for details (go to the Index tab of the online help and type in
    nonlinear).

    Author:
    Altair HyperWorks Technical Support Group (MHS)

    Date this entry was last reviewed:


    April 2005

    Altair Engineering © 2005 Page 2

    Proprietary Information of Altair Engineering.

    You might also like