INTERNATIONAL ISO

STANDARD 725

Second edition
2009-04-15

ISO inch screw threads — Basic

dimensions
Filetages ISO en inches — Dimensions de base

Reference number
ISO 725:2009(E)

--`,,```,,,,````-`-`,,`,,`,`,,`---

Copyright International Organization for Standardization © ISO 2009

Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT

© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
--`,,```,,,,````-`-`,,`,,`,`,,`---

ISO copyright office

Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Contents Page

Foreword............................................................................................................................................................ iv
1 Scope ..................................................................................................................................................... 1
2 Symbols ................................................................................................................................................. 1
3 Basic dimensions ................................................................................................................................. 2
Bibliography ..................................................................................................................................................... 14

--`,,```,,,,````-`-`,,`,,`,`,,`---

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization iii
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 725 was prepared by Technical Committee ISO/TC 1, Screw threads.

This second edition results from the reinstatement of ISO 725:1978, which was withdrawn in 2000 and with
which it is technically identical.

--`,,```,,,,````-`-`,,`,,`,`,,`---

iv
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 INTERNATIONAL STANDARD ISO 725:2009(E)

ISO inch screw threads — Basic dimensions

1 Scope
This International Standard specifies the basic dimensions, in inches, of ISO inch screw threads in
accordance with ISO 263. The values refer to the basic profile in accordance with ISO 68-2.

2 Symbols
D basic major diameter of internal thread (nominal diameter)

d basic major diameter of external thread (nominal diameter)

D2 basic pitch diameter of internal thread

d2 basic pitch diameter of external thread

D1 basic minor diameter of internal thread

d1 basic minor diameter of external thread

H height of fundamental triangle

n number of threads per inch (25,4 mm)

--`,,```,,,,````-`-`,,`,,`,`,,`---

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 1
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

3 Basic dimensions

Dimensions shall be in accordance with Figure 1 and given in Table 1.

The values of D2, d2, D1 and d1 have been calculated from the following equations and rounded, in Table 1, to
the fourth decimal place:

3 0,649 519
D2 = D − 2 × H = D−

--`,,```,,,,````-`-`,,`,,`,`,,`---
8 n

3 0,649 519
d2 = d − 2× H =d−
8 n

5 1,082 532
D1 = D − 2 × H = D−
8 n

5 1,082 532
d1 = d − 2 × H =d−
8 n

where

H = 0,866 025 40 n

a Pitch, P = 1/n.

Figure 1 — Basic dimensions

2
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 — Basic dimensions

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
No. 0 0,060 0 80 UNF 0,051 9 0,046 5
64 UNC 0,062 9 0,056 1
No. 1 0,073 0
72 UNF 0,064 0 0,058 0
56 UNC 0,074 4 0,066 7
No. 2 0,086 0
64 UNF 0,075 9 0,069 1
48 UNC 0,085 5 0,076 4
No. 3 0,099 0
56 UNF 0,087 4 0,079 7
40 UNC 0,095 8 0,084 9
No. 4 0,112 0
48 UNF 0,098 5 0,089 4
40 UNC 0,108 8 0,097 9
No. 5 0,125 0
44 UNF 0,110 2 0,100 4
32 UNC 0,117 7 0,104 2
No. 6 0,138 0
40 UNF 0,121 8 0,110 9
32 UNC 0,143 7 0,130 2

--`,,```,,,,````-`-`,,`,,`,`,,`---
No. 8 0,164 0
36 UNF 0,146 0 0,133 9
24 UNC 0,162 9 0,144 9
No. 10 0,190 0
32 UNF 0,169 7 0,156 2
24 UNC 0,188 9 0,170 9
No. 12 0,216 0 28 UNF 0,192 8 0,177 3
32 UNEF 0,195 7 0,182 2
20 UNC 0,217 5 0,195 9
1/4 0,250 0 28 UNF 0,226 8 0,211 3
32 UNEF 0,229 7 0,216 2
18 UNC 0,276 4 0,252 4
20 UN 0,280 0 0,258 4
5/16 0,312 5 24 UNF 0,285 4 0,267 4
28 UN 0,289 3 0,273 8
32 UNEF 0,292 2 0,278 7
16 UNC 0,334 4 0,307 3
20 UN 0,342 5 0,320 9
3/8 0,375 0 24 UNF 0,347 9 0,329 9
28 UN 0,351 8 0,336 3
32 UNEF 0,354 7 0,341 2

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 3
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
14 UNC 0,391 1 0,360 2
16 UN 0,396 9 0,369 8
7/16 0,437 5 20 UNF 0,405 0 0,383 4
28 UNEF 0,414 3 0,398 8
32 UN 0,417 2 0,403 7
13 UNC 0,450 0 0,416 7
--`,,```,,,,````-`-`,,`,,`,`,,`---

16 UN 0,459 4 0,432 3
1/2 0,500 0 20 UNF 0,467 5 0,445 9
28 UNEF 0,476 8 0,461 3
32 UN 0,479 7 0,466 2
12 UNC 0,508 4 0,472 3
16 UN 0,521 9 0,494 8
18 UNF 0,526 4 0,502 4
9/16 0,562 5 20 UN 0,530 0 0,508 4
24 UNEF 0,535 4 0,517 4
28 UN 0,539 3 0,523 8
32 UN 0,542 2 0,528 7
11 UNC 0,566 0 0,526 6
12 UN 0,570 9 0,534 8
16 UN 0,584 4 0,557 3
18 UNF 0,588 9 0,564 9
5/8 0,625 0
20 UN 0,592 5 0,570 9
24 UNEF 0,597 9 0,579 9
28 UN 0,601 8 0,586 3
32 UN 0,604 7 0,591 2
12 UN 0,633 4 0,597 3
16 UN 0,646 9 0,619 8
20 UN 0,655 0 0,633 4
11/16 0,687 5
24 UNEF 0,660 4 0,642 4
28 UN 0,664 3 0,648 8
32 UN 0,667 2 0,653 7

4
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
10 UNC 0,685 0 0,641 7
12 UN 0,695 9 0,659 8
16 UNF 0,709 4 0,682 3
3/4 0,750 0
20 UNEF 0,717 5 0,695 9
28 UN 0,726 8 0,711 3
32 UN 0,729 7 0,716 2
12 UN 0,758 4 0,722 3
16 UN 0,771 9 0,744 8
13/16 0,812 5 20 UNEF 0,780 0 0,758 4
28 UN 0,789 3 0,773 8
32 UN 0,792 2 0,778 7
9 UNC 0,802 8 0,754 7
12 UN 0,820 9 0,784 8
14 UNF 0,828 6 0,797 7
7/8 0,875 0 16 UN 0,834 4 0,807 3
20 UNEF 0,842 5 0,820 9
28 UN 0,851 8 0,836 3
32 UN 0,854 7 0,841 2
12 UN 0,883 4 0,847 3
16 UN 0,896 9 0,869 8
15/16 0,937 5 20 UNEF 0,905 0 0,883 4
28 UN 0,914 3 0,898 8
32 UN 0,917 2 0,903 7
--`,,```,,,,````-`-`,,`,,`,`,,`---

8 UNC 0,918 8 0,864 7

12 UNF 0,945 9 0,909 8
16 UN 0,959 4 0,932 3
1 1,000 0
20 UNEF 0,967 5 0,945 9
28 UN 0,976 8 0,961 3
32 UN 0,979 7 0,966 2
8 UN 0,981 3 0,927 2
12 UN 1,008 4 0,972 3
16 UN 1,021 9 0,994 8
1 1/16 1,062 5
18 UNEF 1,026 4 1,002 4
20 UN 1,030 0 1,008 4
28 UN 1,039 3 1,023 8

Copyright International Organization for Standardization © ISO 2009 – All rights reserved 5
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
Size inch
D, d n D2, d2 D1, d1
in in in
7 UNC 1,032 2 0,970 4
8 UN 1,043 8 0,989 7
12 UNF 1,070 9 1,034 8
1 1/8 1,125 0 16 UN 1,084 4 1,057 3
18 UNEF 1,088 9 1,064 9
20 UN 1,092 5 1,070 9
28 UN 1,101 8 1,086 3
8 UN 1,106 3 1,052 2
12 UN 1,133 4 1,097 3
16 UN 1,146 9 1,119 8
1 3/16 1,187 5
18 UNEF 1,151 4 1,127 4
20 UN 1,155 0 1,133 4
28 UN 1,164 3 1,148 8
7 UNC 1,157 2 1,095 4
8 UN 1,168 8 1,114 7
12 UNF 1,195 9 1,159 8
1 1/4 1,250 0 16 UN 1,209 4 1,182 3
18 UNEF 1,213 9 1,189 9
20 UN 1,217 5 1,195 9
28 UN 1,226 8 1,211 3
8 UN 1,231 3 1,177 2
12 UN 1,258 4 1,222 3
16 UN 1,271 9 1,244 8
1 5/16 1,312 5
18 UNEF 1,276 4 1,252 4
20 UN 1,280 0 1,258 4
28 UN 1,289 3 1,273 8
6 UNC 1,266 7 1,194 6
8 UN 1,293 8 1,239 7
12 UNF 1,320 9 1,284 8
1 3/8 1,375 0 16 UN 1,334 4 1,307 3
18 UNEF 1,338 9 1,314 9
20 UN 1,342 5 1,320 9
28 UN 1,351 8 1,336 3

--`,,```,,,,````-`-`,,`,,`,`,,`---

6
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
6 UN 1,329 2 1,257 1
8 UN 1,356 3 1,302 2
12 UN 1,383 4 1,347 3

--`,,```,,,,````-`-`,,`,,`,`,,`---
1 7/16 1,437 5 16 UN 1,396 9 1,369 8
18 UNEF 1,401 4 1,377 4
20 UN 1,405 0 1,383 4
28 UN 1,414 3 1,398 8
6 UNC 1,391 7 1,319 6
8 UN 1,418 8 1,364 7
12 UNF 1,445 9 1,409 8
1 1/2 1,500 0 16 UN 1,459 4 1,432 3
18 UNEF 1,463 9 1,439 9
20 UN 1,467 5 1,445 9
28 UN 1,476 8 1,461 3
6 UN 1,454 2 1,382 1
8 UN 1,481 3 1,427 2
12 UN 1,508 4 1,472 3
1 9/16 1,562 5
16 UN 1,521 9 1,494 8
18 UNEF 1,526 4 1,502 4
20 UN 1,530 0 1,508 4
6 UN 1,516 7 1,444 6
8 UN 1,543 8 1,489 7
12 UN 1,570 9 1,534 8
1 5/8 1,625 0
16 UN 1,584 4 1,557 3
18 UNEF 1,588 9 1,564 9
20 UN 1,592 5 1,570 9
6 UN 1,579 2 1,507 1
8 UN 1,606 3 1,552 2
12 UN 1,633 4 1,597 3
1 11/16 1,687 5
16 UN 1,646 9 1,619 8
18 UNEF 1,651 4 1,627 4
20 UN 1,655 0 1,633 4

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 7
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
5 UNC 1,620 1 1,533 5
6 UN 1,641 7 1,569 6
8 UN 1,668 8 1,614 7
1 3/4 1,750 0
12 UN 1,695 9 1,659 8
16 UN 1,709 4 1,682 3
20 UN 1,717 5 1,695 9
6 UN 1,704 2 1,632 1
8 UN 1,731 3 1,677 2
1 13/16 1,812 5 12 UN 1,758 4 1,722 3
16 UN 1,771 9 1,744 8
20 UN 1,780 0 1,758 4
6 UN 1,766 7 1,694 6
8 UN 1,793 8 1,739 7
1 7/8 1,875 0 12 UN 1,820 9 1,784 8
16 UN 1,834 4 1,807 3
20 UN 1,842 5 1,820 9
6 UN 1,829 2 1,757 1
8 UN 1,856 3 1,802 2

--`,,```,,,,````-`-`,,`,,`,`,,`---
1 15/16 1,937 5 12 UN 1,883 4 1,847 3
16 UN 1,896 9 1,869 8
20 UN 1,905 0 1,883 4
4 1/2 UNC 1,855 7 1,759 4
6 UN 1,891 7 1,819 6
8 UN 1,918 8 1,864 7
2 2,000 0
12 UN 1,945 9 1,909 8
16 UN 1,959 4 1,932 3
20 UN 1,967 5 1,945 9
6 UN 2,016 7 1,944 6
8 UN 2,043 8 1,989 7
2 1/8 2,125 0 12 UN 2,070 9 2,034 8
16 UN 2,084 4 2,057 3
20 UN 2,092 5 2,070 9

8
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
4 1/2 UNC 2,105 7 2,0094
6 UN 2,141 7 2,0696
8 UN 2,168 8 2,1147
2 1/4 2,250 0
12 UN 2,195 9 2,1598
16 UN 2,209 4 2,1823
20 UN 2,217 5 2,1959
6 UN 2,266 7 2,1946
8 UN 2,293 8 2,2397
2 3/8 2,375 0 12 UN 2,320 9 2,2848
16 UN 2,334 4 2,3073

--`,,```,,,,````-`-`,,`,,`,`,,`---
20 UN 2,342 5 2,3209
4 UNC 2,337 6 2,229 4
6 UN 2,391 7 2,319 6
8 UN 2,418 8 2,364 7
2 1/2 2,500 0
12 UN 2,445 9 2,409 8
16 UN 2,459 4 2,432 3
20 UN 2,467 5 2,445 9
4 UN 2,462 6 2,354 4
6 UN 2,516 7 2,444 6
8 UN 2,543 8 2,489 7
2 5/8 2,625 0
12 UN 2,570 9 2,534 8
16 UN 2,584 4 2,557 3
20 UN 2,592 5 2,570 9
4 UNC 2,587 6 2,479 4
6 UN 2,641 7 2,569 6
8 UN 2,668 8 2,614 7
2 3/4 2,750 0
12 UN 2,695 9 2,659 8
16 UN 2,709 4 2,682 3
20 UN 2,717 5 2,695 9
4 UN 2,712 6 2,604 4
6 UN 2,766 7 2,694 6
8 UN 2,793 8 2,739 7
2 7/8 2,875 0
12 UN 2,820 9 2,784 8
16 UN 2,834 4 2,807 3
20 UN 2,842 5 2,820 9

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 9
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
Size inch
D, d n D2, d2 D1, d1
in in in
4 UNC 2,837 6 2,729 4
6 UN 2,891 7 2,819 6
8 UN 2,918 8 2,864 7
3 3,000 0
12 UN 2,945 9 2,909 8
16 UN 2,959 4 2,932 3
20 UN 2,967 5 2,945 9
4 UN 2,962 6 2,854 4
6 UN 3,016 7 2,944 6
3 1/8 3,125 0 8 UN 3,043 8 2,989 7
12 UN 3,070 9 3,034 8
16 UN 3,084 4 3,057 3
4 UNC 3,087 6 2,979 4
6 UN 3,141 7 3,069 6
3 1/4 3,250 0 8 UN 3,168 8 3,114 7
12 UN 3,195 9 3,159 8
16 UN 3,209 4 3,182 3
4 UN 3,212 6 3,104 4
6 UN 3,266 7 3,194 6
3 3/8 3,375 0 8 UN 3,293 8 3,239 7
12 UN 3,320 9 3,284 8
16 UN 3,334 4 3,307 3
--`,,```,,,,````-`-`,,`,,`,`,,`---

4 UNC 3,337 6 3,229 4

6 UN 3,391 7 3,319 6
3 1/2 3,500 0 8 UN 3,418 8 3,364 7
12 UN 3,445 9 3,409 8
16 UN 3,459 4 3,432 3
4 UN 3,462 6 3,354 4
6 UN 3,516 7 3,444 6
3 5/8 3,625 0 8 UN 3,543 8 3,489 7
12 UN 3,570 9 3,534 8
16 UN 3,584 4 3,557 3
4 UNC 3,587 6 3,479 4
6 UN 3,641 7 3,569 6
3 3/4 3,750 0 8 UN 3,668 8 3,614 7
12 UN 3,695 9 3,659 8
16 UN 3,709 4 3,682 3

10
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
4 UN 3,712 6 3,604 4
6 UN 3,766 7 3,694 6
3 7/8 3,875 0 8 UN 3,793 8 3,739 7
12 UN 3,820 9 3,784 8
16 UN 3,834 4 3,807 3
4 UNC 3,837 6 3,729 4
6 UN 3,891 7 3,819 6
4 4,000 0 8 UN 3,918 8 3,864 7
12 UN 3,945 9 3,909 8
16 UN 3,959 4 3,932 3
4 UN 3,962 6 3,854 4
6 UN 4,016 7 3,944 6
4 1/8 4,125 0 8 UN 4,043 8 3,989 7
12 UN 4,070 9 4,034 8
16 UN 4,084 4 4,057 3
4 UN 4,087 6 3,979 4
6 UN 4,141 7 4,069 6
4 1/4 4,250 0 8 UN 4,168 8 4,114 7
12 UN 4,195 9 4,159 8
16 UN 4,209 4 4,182 3
4 UN 4,212 6 4,104 4
6 UN 4,266 7 4,194 6
4 3/8 4,375 0 8 UN 4,293 8 4,239 7
12 UN 4,320 9 4,284 8
16 UN 4,334 4 4,307 3
4 UN 4,337 6 4,229 4
6 UN 4,391 7 4,319 6
4 1/2 4,500 0 8 UN 4,418 8 4,364 7
12 UN 4,445 9 4,409 8
16 UN 4,459 4 4,432 3
4 UN 4,462 6 4,354 4
6 UN 4,516 7 4,444 6
4 5/8 4,625 0 8 UN 4,543 8 4,489 7
12 UN 4,570 9 4,534 8
16 UN 4,584 4 4,557 3
--`,,```,,,,````-`-`,,`,,

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 11
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
4 UN 4,587 6 4,479 4
6 UN 4,641 7 4,569 6
4 3/4 4,750 0 8 UN 4,668 8 4,614 7
12 UN 4,695 9 4,659 8
16 UN 4,709 4 4,682 3
4 UN 4,712 6 4,604 4
6 UN 4,766 7 4,694 6
4 7/8 4,875 0 8 UN 4,793 8 4,739 7
12 UN 4,820 9 4,784 8
16 UN 4,834 4 4,807 3
4 UN 4,837 6 4,729 4
6 UN 4,891 7 4,819 6
5 5,000 0 8 UN 4,918 8 4,864 7
12 UN 4,945 9 4,909 8
16 UN 4,959 4 4,932 3
--`,,```,,,,````-`-`,,`,,`,`,,`---

4 UN 4,962 6 4,854 4
6 UN 5,016 7 4,944 6
5 1/8 5,125 0 8 UN 5,043 8 4,989 7
12 UN 5,070 9 5,034 8
16 UN 5,084 4 5,057 3
4 UN 5,087 6 4,979 4
6 UN 5,141 7 5,069 6
5 1/4 5,250 0 8 UN 5,168 8 5,114 7
12 UN 5,195 9 5,159 8
16 UN 5,209 4 5,182 3
4 UN 5,212 6 5,104 4
6 UN 5,266 7 5,194 6
5 3/8 5,375 0 8 UN 5,293 8 5,239 7
12 UN 5,320 9 5,284 8
16 UN 5,334 4 5,307 3
4 UN 5,337 6 5,229 4
6 UN 5,391 7 5,319 6
5 1/2 5,500 0 8 UN 5,418 8 5,364 7
12 UN 5,445 9 5,409 8
16 UN 5,459 4 5,432 3

12
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Table 1 (continued)

Number of
Major Thread Pitch Minor
threads per
diameter series diameter diameter
inch
Size
D, d n D2, d2 D1, d1
in in in
4 UN 5,462 6 5,354 4
6 UN 5,516 7 5,444 6
5 5/8 5,625 0 8 UN 5,543 8 5,489 7
12 UN 5,570 9 5,534 8
16 UN 5,584 4 5,557 3
4 UN 5,587 6 5,479 4
6 UN 5,641 7 5,569 6

--`,,```,,,,````-`-`,,`,,`,`,,`---
5 3/4 5,750 0 8 UN 5,668 8 5,614 7
12 UN 5,695 9 5,659 8
16 UN 5,709 4 5,682 3
4 UN 5,712 6 5,604 4
6 UN 5,766 7 5,694 6
5 7/8 5,875 0 8 UN 5,793 8 5,739 7
12 UN 5,820 9 5,784 8
16 UN 5,834 4 5,807 3
4 UN 5,837 6 5,729 4
6 UN 5,891 7 5,819 6
6 6,000 0 8 UN 5,918 8 5,864 7
12 UN 5,945 9 5,909 8
16 UN 5,959 4 5,932 3

© ISO 2009 – All rights reserved

Copyright International Organization for Standardization 13
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

Bibliography

[1] ISO 68-2, ISO general-purpose screw threads — Basic profile — Part 2: Inch screw threads

[2] ISO 263, ISO inch screw threads — General plan and selection for screws, bolts and nuts — Diameter
range 0.06 to 6 in

[3] ISO 5408, Screw threads — Vocabulary

--`,,```,,,,````-`-`,,`,,`,`,,`---

14
Copyright International Organization for Standardization © ISO 2009 – All rights reserved
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 --`,,```,,,,````-`-`,,`,,`,`,,`---

Copyright International Organization for Standardization

Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale
 ISO 725:2009(E)

ICS 21.040.20
Price based on 14 pages

--`,,```,,,,````-`-`,,`,,`,`,,`---

© ISO 2009
Copyright International – Allforrights
Organization reserved
Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS Not for Resale