BARCODE LABEL SCALE

SALES OPERATION
MANUAL
MODEL: LS2R15，LS2R30

LS2C15，LS2C30

LS2N15，LS2N30

Pinnacle Technology Corp.

 STATEMENT
Please refer to PC software management manual in attached CD

about the PLU editing, hotkey downloading, label editing and

parameter setting etc.

 CONTENT

1 SUMMARIZATION .......................................................................................................................................... 1
2 SPECIFICATION .............................................................................................................................................. 2
3 APPEARANCE ................................................................................................................................................. 4
4 INSTALLATION ............................................................................................................................................... 6
4.1 Install display pole ............................................................................................................................. 6
4.2 Power on/off ...................................................................................................................................... 7
4.3 Paper Installation ............................................................................................................................... 8
4.3.1 Label Paper Installation .......................................................................................................... 8
4.3.2 Receipt Paper Installation ......................................................................................................11
4.3.3 Linerless Paper Installation .................................................................................................. 13
5 PRINTER REPLACEMENT........................................................................................................................... 14
6 SALES OPERATION ...................................................................................................................................... 17
6.1 Weight Unit Selection ...................................................................................................................... 17
6.2 Calculate by Weight ......................................................................................................................... 17
6.3 Tare Operation ................................................................................................................................. 19
6.4 Calculate by Piece............................................................................................................................ 19
6.5 Discount ........................................................................................................................................... 21
6.6 Change Price .................................................................................................................................... 21
6.6.1 Permanently Change Price.................................................................................................... 21
6.6.2 Temporarily Change Price .................................................................................................... 22
7 SOME SIMPLE OPERATION ........................................................................................................................ 24
7.1 Copy price label ............................................................................................................................... 24
7.2 Print receipt...................................................................................................................................... 24
7.3 Normal Package ............................................................................................................................... 24
7.4 Package by Fixed weight ................................................................................................................. 24
7.5 Package by Fixed Price .................................................................................................................... 25
7.6 Piece Together Usage....................................................................................................................... 25
8 FUNCTION SET ............................................................................................................................................. 27
8.1 PLU Set............................................................................................................................................ 27
8.2 System Set ....................................................................................................................................... 28
8.3 Function Lock .................................................................................................................................. 29
8.4 Lock Scale ....................................................................................................................................... 29
9 COMMUNICATION SETUP .......................................................................................................................... 30
9.1 Handshaking Flowchart of Label Scale and Background ................................................................ 31
9.2 Making procedure of connector ....................................................................................................... 33
10 TROUBLESHOOTING .......................................................................................................................... 34
11 APPENDIX ............................................................................................................................................. 37
11.1 Appendix 1: Barcode Coding List ................................................................................................... 37
11.2 Appendix2: Main difference between LB scale and LP scale: ........................................................ 39
11.3 Main difference between label scale and receipt scale .................................................................... 39
 1 SUMMARIZATION
 Simple and easy to operate
1. You can use single key to sell PLU quickly. Clerk can operate this scale without training.
2. This scale has 112 direct keys (224 hotkeys can be set) and can set hotkeys for most of the common goods.

 Advanced function and endurance

1. Firmware program can be updated through PC in order to keep advanced and up to date.
2. FlashRom protection function assures the security of program and source.
3. Keyboard can be cleaned. It resists dirty with great validity.
4. Printer is designed elaborately and not easily subject to paper jam.
5. Barcode rotation can prolong the life of printer head. Printer core can be adjusted according to label paper.
6. Printer can load 1000 pieces of label paper while other printer can only load 800 pieces of label paper.
7. There are several package methods (fixed weight, and fixed price). Barcode printer is specially designed.
8. Piece together function, which can gather several kinds of commodity as required, such as fruit basket.
9. 12000 pieces of PLU can meet all kinds of demand.
10. Every piece of PLU can be set to use multiple labels.
11. Every piece of PLU can use single barcode format, which resolves the coding problems during selling.
12. Every piece of PLU can use single metric unit.
13. Numeric unit can be defined by user such as block, package and entries.
14. Sufficient PLU message includes barcode format, live commodity Code and package type and so on.
15. Label can be printed in rotated position.
16. Support 8 code, Ean-13 code, and 18 code and resolve the coding problem of live commodity.
17. Special barcode type for the convenience of live commodity lot management.

 Convenient, flexible and powerful software support

1. What you see in label designing is what you get. Label size can be selected. Volume of smallest area can be created
according to user. Thus we can decrease cost greatly.
2. International design and supporting worldwide language make it unnecessary to add any accessory.
3. We can adjust the popular commodity at any time and improve the foregrounding working efficiency greatly.
4. Downloading data can be executed in scheduled time.
5. Background discounts fixedly.
6. Discount in different period of time. Ten discount modes can be defined and each mode has five periods of time using
different discount rate.
7. It supports broadcast downloading.
8. With the function of FTP and TCP/IP. The software supports Unix system and Internet.
9. We can set POS program parameters on PC.
10. Its management is separated into machine, commodity, and hotkey, which make usage of the scale optimum.
11. We can edit and print keyboard sheet quickly with this software.
12. Locking the POS function key can control its operation such as locking discount key and PLU edit key. Also it offers
function to unlock password.
13. It is managed by multi-user and records login information automatically in order to supervision.
14. It offers dynamic link library for the convenience of user‟s second development.

1
2 SPECIFICATION

Resolve segment
Power: AC 100V~240V 50/60Hz 1A
Working temperature: 0℃-40℃
Precision grade: Ⅲ
A/D resolving rate: 30000
Verification scale interval: LS2615: 0kg~6kg e=2g
6kg~15kg e=5g
LS215: 0kg~15kg e=5g
LS21530: 0kg~15kg e=5g
15kg~30kg e=10g
Number of verification scale interval: 3000

Printer:
Printer driver: 24V
Number of dots/line: 448dots/per line
Dot spacing: 0.125mm

LCD:
Message/weight: 24×110 dots
Price: 8×110 dots
Total price: 7×110 dots
Dimension:

344.9mm
(13.6

478.3mm
(18.8
263.4mm
(10.4

158.2mm
(6.2

( 1 4 .3 (16.9 (4.9
364.0m m 429.1mm 124.0mm

[LS2R]

2
[LS2C]

[LS2N]

3
3 APPEARANCE

LS2R:
Display

Power switch

Tray

Printer
Hotkey Function key

Numerical key

LS2C:

Display

Power switch

Tray

Printer
Hotkey Function key

Numerical key

4
 LS2N:

Operator Display
Power switch

Tray

Printer
Hotkey Function key

Numerical key

Clearing pen

Note: If the printer head is dirty, clean

hot sensor head softly with the cleaning
pen attached. The cleaning pen is an
alcohol pen; please cover it immediately
after you wipe the dirty off.
Gradienter

Note: As for cleaning the thermal printer head, please refer to Chapter 10.

5
4 INSTALLATION
4.1 Install display pole

o o
2. Open the LCD cover 3 ~5 ，
1. Take out the fix set
and Mount the display pole.

3. Cover the LCD, then put on fix set 4. Put on fix set .Connect the line, and
like the picture shows. fix the 4 screws.

6
 Gradienter, which is Circumvolve the 4 feet to adjust the level of
under the tray scale, and make the air bladder into the red
circle.

4.2 Power on/off

At the first ten seconds after you turn on the scale, the LCD displays from “9” to “0” to enter self-testing.
Please wait and do not press any key, system initialization is going on.
“On/Off” key is used to turn on or turn off the scale softly. Press this key and hold it for 2 seconds to turn off
the scale, and so as how to turn down it. (Note: this key takes effect by the condition that the plug has
connected and the power switch under the scale is turned on.)
We suggest that you should use On/Off key to turn On/Off the scale, and do not pull out the power plug
directly if it hasn‟t been softly turned down, especially if the scale is under the conditions of connecting with
network or downloading data.

7
4.3 Paper Installation
4.3.1Label Paper Installation
Notice: please take the conveying protection bolt down, when you load the paper for the first time.

Conveying protection bolt

(1) Open the side cover (2) Take out the printer, and open the turnable
printing assembly

(3) Rip off the first several labels. (4) Insert the release paper to the rewinder

paper-fixing-block

(5) Roll the release paper in the rewinder axis, and

adjust the paper-fixing-block to fix the roll paper.

8
 (6) Close the turnable printing assembly. (7) Close the side cover

1 4

1. Turn the bar out wards, open the turnable printing assembly in the direction shown as the
arrowhead ○ 1

2. Please rip off the first several labels, load paper in the direction shown as the arrowhead ○ 2 , roll the

release paper in the rewinder axis as the direction of arrowhead ○ 3 shows.

3. Push the turnable printing assembly to the right position in the direction shown as the arrowhead
○4 .
4. When every five-paper roll is used up, or the labels print unclearly, please clean the printing head by
using cotton dipping cleaning oil or alcohol.

9
 Press this key for 2 seconds; the scale will adjust the paper‟s
position automatically; you yourself can also press it to adjust
the paper minitrimly.

Note: if the paper‟s position is inaccurate after pressing the “FEED” key for the first time, pleas press this key
again to relocate the paper‟s position.

 Label Paper
We have two types of label paper: no-gap paper and gap paper

No-gap paper Gap paper（2mm）

The label paper we produced is very suitable for label scale. It is a kind of environment protecting material has
suitable thickness, high sensitivity and low price. We can produce any kind of specification label paper to match
your request. Order easily, dial 86-592-5710087 or log on our company website www.aclas.com

10
4.3.2 Receipt Paper Installation
1. Install the receipt paper-cutter.

2. Open the turnable printing assembly.

3. Load the paper like the map shows (directly lead the thermal paper to the paper outlet).

11
4. Pay attention to adjust the paper-fixing-block until the paper roll is fixed.

Paper-fixing-block

5. Close the turnable printing assembly.

6. Close the side cover.

NOTE: If you use thermal paper instead of label, you should choose „RECEIPT‟ in „System Set‟. Please
refer to Chapter 7.2 „Print receipt‟.

12
 4.3.3 Linerless Paper Installation
Note: The linerless paper printing module is different from the receipt and label printing module. If
customers bought was the receipt or label printing module, but now want to replace it to the linerless paper
module, please contact the service department.
Please pre-set the related items when you print linerless paper.
1) Press “System set” for seconds to enter the related setting, and then press key “ ”“ ” till the
LCD display “Gap paper” and choose “Yes”, and then press the key “Print/Enter” to confirm.
2) Press “System set” for seconds to enter the related setting, and then press key “ ”“ ” till the
LCD display “paper type”, please choose “black label”, and then press the key “Print/Enter” to confirm.

1. Open the side cover and rotatable printing assembly. 2. Load the paper like the map shows (directly
lead the thermal paper to the paper outlet).

13
 3 Close the rotatable printing assembly 4 Close the side cover

5 PRINTER REPLACEMENT
If the printer is damaged, you can follow the steps below to replace a new one.

Precaution:
 Before you do the following operations, please cut the power supply first.
 Do not disassemble, assemble or adjust the printer if it is operating satisfactorily. In particular, do not
carelessly loosen the screws holding various parts in place.
 When servicing, be sure not to leave used parts or screws, etc.

1. Demount the damaged printer

Open the printer cover.

Pull out the printer

14
Use a screwdriver to push the latch to the left side.

Lift up the printer

15
 Pull out the cable

2. Install a new one

Install new printer by following the demount procedure in reverse order.

16
6 SALES OPERATION
6.1 Weight Unit Selection
Operation step for price unit selection

DISPLAY
OPERATION STEP KEY REMARK
Unit
Weight Total
price
1 Press UNIT key without
releasing, or release the
After step, the unit will be display
key after two seconds. Unit 0.000kg 0.00 0.00
circularly.
Repress the key when hear
a sound.
2 Select unit. For example,
select PCS (g) as the unit. 0g 0.00 0.00

6.2 Calculate by Weight

There are three kinds of operation. If PLU data is downloaded by background server PC or pre-edited in the
scale, operation follows method 1 or method 2. Otherwise the operation follows method 3.

Picture 1 can help you understand the operation.

Name Fix Weight Fix Price

Zero ◄
Tare Art.NO.
Auto ◄

0.000kg 0.00 0.00

Weight Price Lock Unit Price Total

Notes:
1. AUTO state: On the condition that the weight and the unit are nonzero and after the weight is steady, a
label will be printed. When power on, “AUTO” signal is lighted, which means the scale is in “AUTO” state.
Press “AUTO” key to switch off the state. Suggest making “AUTO” state as default state.
2. ZERO state: There is nothing on the pan. Press “ZERO” key to let the weight zero and the “ZERO” signal
will be on.
3. Usage of Print key: All of the following operations including Calculate by Weight, Tare Operation, and
Calculate by Piece, Discount, and Change Price are in the “Auto” state. If the default state is not “Auto”
state, the Auto arrow on the LCD won‟t be lightening, you must press Print key in order to print the label.

17
 METHOD 1: HOTKEY OPERATION

Trade example: Some onions weighing 2.000kg are sold . Its hotkey is 01, and price is 0.500$/kg.

ARROW DISPLAY
OPERATION STEP KEY Unit REMARK
Zero Auto Weight Total
price
1. Press “ZERO” key to let the Ignore this step if the
Zero 0.000kg 0.00 0.00
scale return to zero scale is in “ZERO” status.
2. Put the onions 2.000kg on the
2.000kg 0.00 0.00
pan.
3. Input the hotkey 01 of the
01 2.000kg 0.50 1.00
onions through PLU keyboard
This step is optional. If
*4. Cancel “AUTO” state Auto 2.000kg 0.50 1.00 you want to switch off the
“Auto” state, do this step.
Only after you take the
above step 4 and want to
*5. Set “AUTO” state Auto 2.000kg 0.50 1.00
set “Auto” state, take this
step.

NOTES:
1) There are 224 hotkey. These hotkeys can be changed randomly and be printed in a sheet quickly by
the background PC.
2) The above opreation is for the hotkeys from 1 to112. As to hotkeys from 113 to 224, the above
operation step 3 should be changed as follows: Press “PLU” key and press the hotkey no. of the
commodity. Other steps are the same.

METHOD 2: General operation step

Trade example: Some onions weighing 2.000kg are sold. Their LFCODE is 10, unit price is 1.500$/kg.

ARROW DISPLAY
OPERATION STEP KEY Unit REMARK
Zero Auto Weight Total
price
Ignore this step if the
1. Press “ZERO” key to make the
ZERO 0.000kg 0.00 0.00 scale is in “ZERO”
scale return to zero.
status.
2. Put the onions weighing
2.000kg 0.00 0.00
2.000kg on the pan.
LLFCODE?
3. Press “PLU” key PLU
(1-6)
4. Input LFCODE 10 of the LLFCODE?
10 10.00
onions through small keyboard. (1-6)
Ignore this step if the
5. Press PLU key. PLU 2.000kg 1.50 3.00
LFCODE has 6 digits.

18
 METHOD 3: operation for PLU without settings.
ARROW DISPLAY
OPERATION SETP KEY Unit REMARK
Zero Auto Weight Total
price
Ignore this step if
1. Press “ZERO” key to make the
Zero 0.000kg 0.00 0.00 the scale is in
scale return to zero state.
“ZERO” status.
2. Press “UNIT” key without
releasing to select a correct price Unit 0.000kg 0.00 0.00
unit such as kg.
3. Input unit price 2.00 through the
2 0 0 0.000kg 2.00 0.00
small keyboard.
4. Put on the commodity weighing
1.000kg 2.00 2.00
1.0kg.

6.3 Tare Operation

It is only applicable to the commodity packed in package or container such as eggs, beans or fruit and so on.

MOTHOD: Operation for commodity separated from container or package.

Trade example: A package of apples is sold. The hotkey of apples is 05, the net weight is 2.000kg and unit price
is 6.000$/kg.
ARROW DISPLAY
OPERATION KEY Unit REMARK
Zero Auto Tare Weight Total
price
1. Put the container or
package weighing 1.000kg 0.00 0.00
1.000 kg on the pan.
The “TARE” signal flashing
2. Press “TARE” key. Tare 0.000kg 0.00 0.00 means the scale is in the
weight-deducting state.
3. Put a page of
apples weighing 2.000kg 0.00 0.00
2.000kg on the pan.

4. Key in the hotkey

05 of apple through 05 2.000kg 6.00 12.00
PLU keyboard.
5. Take away the
container and the This step is to leave the
apples on the tray, Tare 0.000kg 0.00 0.00 weight-deducting state. The
then press “TARE‟ arrow of “tare” disappears.
key.

6.4 Calculate by Piece

There are three kinds of operation methods. The following operation of method 1 and method 2 is suitable for
PLU already downloaded by background sever or pre-edited on the scale. And method 3 is for PLU not pre-edited.

Note: Before you taking these two operations, please make sure the PLU is pre-edited with piece
calculation.

19
 METHOD 1: Hotkey operation step
Trade example: Ten pieces of cake are sold. The hotkey of cake is 05.
ARROW DISPLAY
OPERATION KEY Unit REMARK
Zero Auto Weight Total
price
1. Input the number of the
commodity through small 1 0 0.000kg 0.10 0.00
keyboard. For example 10.
The LCD returns to
2. Press “UNIT” key. Unit 0.000kg 0.00 0.00 initial state after “unit”
key is pressed.
3. Press the corresponding hotkey
05 of the cake through PLU 05 0.000kg 3.00 30.00
keyboard.
METHOD 2: general operation step
Trade example: Ten pieces of cakes are sold and the LFCODE of the cake is 12.
ARROW DISPLAY
OPERATION KEY Unit REMARK
Zero Auto Weight Total
price

1. Input the number of the cake 10

1 0 0.000kg 0.10 0.10
through small keyboard.

2. Long press “UNIT” key and KG

Unit 0.00 0.00
select a unit such as PCS (Kg). 0.000kg

LLFCOD?
3. Press “PLU” key. PLU
(1-6)

4. Input LFCODE of the cake

1 2 LLFCODE? 12
12 through small keyboard.
(1-6)
Ignore this step if
5. Press “PLU” key PLU 0.000Kg 3.00 30.00 the LFCODE has 6
digits.
METHOD 3: operation for PLU without pre-edited.

ARROW DISPLAY
OPREATION KEY Unit REMARK
Zero Auto weight Total
price

1.Press “Unit” key without

releasing to select the correct unit Unit 0.000Kg 0.00 0.00
price such as PCS (Kg)
2. Input the number of the
commodity through numeric 1 0 0.000Kg 0.10 0.10
keyboard. For example 10.

3. Press “unit” key. Unit 0.000Kg 0.00 0.00

4. Input unit price through the

2 0 0 0.000Kg 2.00 20.00
numeric keyboard. For example 2.0.

20
6.5 Discount
Discount function can be locked by password which is set and can be randomly changed by background sever PC.

METHOD: operation for proportional discount.

Trade example: some peaches give a discount of 95. Its unit is 8.0$/kg and hotkey is 12.
ARROW DISPLAY REMARK
OPERATION KEY Unit
Zero Auto weight Total
price
1. Input discount proportion
of the commodity 9 5 9 5 0.000kg 0.95 0.00
through numeric keyboard.
The LCD returns to
initial state after
2. Press Discount key. Discount 0.000kg 0.00 0.00
DISCOUNT key is
pressed.
3. Put the commodity
1.000kg 0.00 0.00
weighing 1.000kg on the pan.

4. Key in the corresponding

12 1.000kg 8.00 7.60
hotkey of the peaches e.g. 12.

Notes:
As for step 3 and 4, please refer to the operation of „calculate by weight‟. You can choose other kinds of
operation such as normal operation or operation for pre-edited PLU to proceed with the above operation.

6.6 Change Price

Change the unit price of a commodity. There are two methods to change the unit price of a commodity, they are
permanently change price and temporarily change price.

6.6.1 Permanently Change Price

METHOD 1:
Trade example: The unit price of the apples 4.000$/kg. After changing price, its unit price is 3.000$/kg and the
hotkey is 05.

ARROW DISPLAY
OPERATION KEY Unit
Zero Auto Weight Total
price

1. Key the hotkey 05 of the apples via PLU keyboard. 05 0.000kg 4.00 4.00

2. Press Change price key. Change Price ? PRICE? 0.00 4.00

3. Key in the new price 3.000$/kg. 300 ? PRICE? 3.00 4.00

4. Press Enter key. Enter 0.000kg 3.00 0.00

5. Proceed with the normal operation of weighing or
granular price calculating.

METHOD 2:
Trade example: Some apples are sold. The unit price of the apple is 4.000$/kg, and LFCODE is 900001. After
change the unit price, the unit price of the apple is 3.000$/kg.

21
 ARROW DISAPLY
OPERATION KEY Unit
Zero Auto Weight Total
price
LLFCODE?
1. Press Change price key. Change Price
(1-6)
2. Key in the LFCODE 900001 of the
900001 ? PRICE? 0.00
apples through small keyboard.
4. Key in the price changed 3.000. 300 ? PRICE? 3.00

5. Press Enter key. Enter 0.000kg 3.00 0.00

6. Proceed with the normal operation of
„calculate by weight‟ or „calculate by
piece‟.

6.6.2 Temporarily Change Price

METHOD 1: temporarily change the price of cherry（its original price is 24.0$/PCS(g)）。

Trade Example：Sell 10 cases of the cherry, temporarily change the price as 30.0$/PCS(g), and its hotkey is 11.
When finish this dealing, it will recover to the original price 24.0$/PCS(g).

ARROW DISAPLY
OPERATION KEY REMARK
Zero Auto Weight Unit price Total

1. Key in 10 (10 cases)

1 0 0.000kg 0.10 0.00
via the numeric key.
Display is
2. Press Unit key. Unit 0.000kg 0.00 0.00 back to the
initial status.
Begin with
this step if
3. key in the new price
3 000 0.000kg 30.00 0.00 sell the
30$/PCS(g)
commodity
by unit.

4.Press Comm. Test key Comm. Test 0.000kg 0.00 0.00

5. Key the hotkey 11 of

the cherry via PLU 1 1 0.000kg 30.00 300.00
keyboard.
METHOD 2:
Trade Example： The unit price of the cheese is 4.000$/ PCS (g), and LFCODE is 15. Change the unit price of
the cheese as 3.000$/kg. When finish this dealing, it will recover to the original price 4.000$/PCS (g).
ARROW DISAPLY
OPERATION KEY REMARK
Zero Auto Weight Unit price Total
1. Key in the LFCODE
15 of the cheese via 1 5 0.000kg 15 0.00
small keyboard.
2. Press Change price Change
? PRICE? 0.00 0.00
key. Price
3. Key in the new price
3 0 0 ? PRICE? 3.00 0.00
3.0 $/PCS (g).

4. Press Print key. Print 0.000kg 3.00 3.00

22
METHOD 3: Temporarily change the PLU whose initial unit price is 0$/kg.
1. Trade Example 1：Suppose the initial price of the cherry is 0$/kg, and now temporarily change it as 30.0$/kg,
and its hotkey is 11. When finish this dealing, it will recover to the initial price 0$/kg.

ARROW DISAPLY
OPERATION KEY Unit REMARK
Zero Auto Weight Total
price
1. Put the cherry
weighted 1kg onto the 1.000kg 0.00 0.00
scale.
2. key in the new price
3000 1.000kg 30.00 30.00
30$/kg
3. Key the hotkey 11 PLU with its unit
of the cherry via PLU 11 1.000kg 30.00 30.00 price as 0 cannot be
keyboard. sold directly.
2. Trade Example 1：The original unit price of PLU is 0$/kg, sell with LF-code.
Suppose the initial price of the cherry is 0$/kg, and now temporarily change it as 30.0$/kg, and its LF-code is 13.
When finish this dealing, it will recover to the initial price 0$/kg.
ARROW DISAPLY
OPERATION KEY Unit REMARK
Zero Auto Weight Total
price
1. Put the cherry
weighted 1kg onto 1.000kg 0.00 0.00
the scale.
PLU with unit
2. Key in LF-code 13
price 0$/kg
via the numeric 1 3 1.000kg 0.13 0.00
can‟t be sell
keypad. directly.

3. Press key PLU PLU ? PRICE? 0.00 30.00

4. key in the new

3 0 0 0 ? PRICE? 30.00 30.00
price 30$/kg
Ignore this
step if the
5. Press Print key. Print 1.000kg 30.00 30.00
LFCODE has
6 digits.
METHOD 4: Temporarily change the price of the PLU, which is needed to be weighted.
Trade Example：The unit price of the cabbages is1$/kg, and it should be change price as 2$/PCS in the evening to
promote it. When finish this dealing, it will recover to its initial price 1$/kg.
Suppose a cabbage is 3kg, and its hotkey is 13.
ARROW DISAPLY
OPERATION KEY Unit REMARK
Zero Auto Weight Total
price
1. Put the cabbage
3.000kg 0.00 0.00 Sell by PCS now.
onto the scale.
2. Key in the new
200 3.000kg 2.00 6.00
price 2$/PCS.
3．Press Comm. Test
Comm. Test 3.000kg 0.00 0.00
key
4. Key the hotkey 13
of the cabbage via 13 3.000kg 2.00 2.00
PLU keyboard.

23
 7 SOME SIMPLE OPERATION
7.1 Copy price label
1. Call PLU or input unit price in normal state and print a piece of label.
2. Press “Copy” key and input a number between 1 and 9, then the corresponding number pieces of label is
printed.
3. Press Copy key and 0 key to print 1000 pieces of label continuously.

7.2 Print receipt

1. Reloaded the rolling paper and extend its head out of the outlet. Make sure not roll the paper head in the
rewinder. Please refer to Chapter 4.3.2 Receipt Paper Installation.
2. Use key [→] or [←] to select the paper type as „RECEIPT‟.
3. Press Enter key to confirm.
Note:
If you want to use label paper again, you should enter this function to select the paper type as „LABEL‟, and
after setting you must restart the scale by press the on-off on the scale‟s bottom (switch to „RECEIPT‟ no
need restart the scale).
7.3 Normal Package
This is suitable to quickly pack a same commodity (or different commodity with the same unit price) with
different weight. (The Package Type is set as „Normal‟ on the scale software „PLU manager‟.
1. Start up the function of “Auto” and “Price lock” (these two indicator light are lighting)
2. Select PLU or input the unit price.
3. Put the commodity (to be packed) on the pan and the label will be printed automatically.
1. Put commodity 1 on the pan
2. After the label is printed automatically put commodity 2 on the
pan at the same time, take away commodity 1.
3. Take away the label and stick it on commodity 1. The label of
Note: the operation of the right is the commodity 2 will be printed out.
suggested if you want to operate quickly. 4. Put commodity 3 on the pan and take away commodity 2.
5. Take away the label and stick it on commodity 2, the next label
will be printed.
6. Repeat as the above steps to overlap the time of waiting for
printing label and sticking label.

7.4 Package by Fixed weight

Fix weight package, this function is available by setting on PC software first. Please refer to the related
chapter “package by fixed weight” on “LS2X scale PC software management” in attached CD..
For example: pack fish by the fixed weight 0.255kg, and the corresponding hotkey is 38.
Note: Before operate on the scale, please press key Price Lock first, and the indicator light for „price lock‟
will be lighting.

24
 ARROW Display
OPERATION KEY Fix Unit Remark
Zero Auto Weight Total
Weight Price
1. Put the fish on
0.255kg 0.00 0.00
the pan.
2. Press the hotkey
38 of the fish via 38 0.255kg 70.00 17.85
PLU keyboard.

Attention: The commodity can be sold at the condition that its weight is between the weight tolerance
+5%kg while it is in Fixed Weight package mode.

7.5 Package by Fixed Price

Fix price package, this function is available by setting on PC software first. (As for the PC software operation,
please refer to Chapter “Package by Fixed Weight” in attached CD. And choose the item „Fixed Price‟ in the
column „Package Type‟, input the fixed price in the column „Unit Price‟, and input the weight value for the
commodity‟s fixed price in the column „Package Weight‟
Note：1. after download the setting data to the scale, the indicator light for „Fixed Price‟ will be lighting;
2. before operate on the scale, please press key Price Lock first, and the indicator light for „price lock‟
will be lighting.

ARROW DISPLAY
OPERATION KEY Unit REMARK
Zero Auto Fix Price Weight Total
Price
1. Put the fish on
0.505kg 0.00 0.00
the pan.
2. Press the hotkey
38 of the fish via 38 0.505kg 0.00 35.35
PLU keyboard.

Attention: The commodity can be sold at the condition that its total price is between the package tolerance
$+5% while it is in Fixed Price package mode.
7.6 Piece Together Usage
Piece together function is usually used in the aspect, such as pack gift-box and fruit-dish.
This function is available by setting a hotkey „piece together‟ on PC software first. As for the PC software
operation, please refer to Chapter “Piece together usage” in attached CD.
Note：1. After download the setting data to the scale, the indicator light for „Fixed Weight‟ and „Fixed Price‟
will be lighting;
2. Before operate on the scale, please press key Price Lock first, and the indicator light for „price lock‟ will
be lighting.

For example：Package a fruit-dish (apple, grape, and orange)

PLU name：apple weight unit：kg unit price：10.00 $/kg hotkey 06
PLU name：orange weight unit：kg unit price：4.00 $/kg hotkey 07
PLU name：grape weight unit：kg unit price：20.00 $/kg hotkey 08

Suppose each of the three fruits is 1.000kg.

25
 ARROW DISPLAY
OPERATION KEY Fix weight Unit REMARK
Zero Auto Weight Total
Fix price Price
1. Press hotkey 01
0.000kg 0.00 0.00

2. Put the apple on

the pan, and 06 1.000kg 0.00 0.00
press hotkey 06
3. Put the orange on
the pan, and 07 2.000kg 0.00 0.00
press hotkey 07
4. Put the grape on
the pan, and 08 3.000kg 0.00 0.00
press hotkey 08

5. Press hotkey 01 01 3.000kg .34.00 34.00

26
8 FUNCTION SET
8.1 PLU Set
Notes: This operation can be locked by password that is set in background PC changed randomly.

 PLU Input
1.Press PLU key for 2 seconds. The display shows “PLU EDIT”, it means the system is in the state of editing
PLU.
2. Key in LFCODE when the display prompt “LLFCODE?”, and press Enter to confirm. Then the display shows
“NAME” and enter editing items: N/L/C/P/U/F/T/B/D/W/Y/M/G/I/R/S, you can use key ← and → to choose
the item you want to edit, then press Enter.
3. Press Enter key. Input the corresponding data by sequence. Refer to the following notes.
4. Press S or Enter to save the above operation.

NOTES: the following is the sequence of PLU data input. When one item is input, press Enter to confirm. The
system will shift to another item, and press Enter again to enter it. If no contents are inputted, press ESC to exit.

1) N---PLU NAME: Input PLU name not exceeding 36 characters directly through keyboard. And through the
numeric keyboard input the code of the input characters. The code is in the word stock table.
2) L---LFCODE: Input Life and Fresh Code within 6 digits.
3) C---PLU CODE: Input PLU code within 10 digits.
4) P---UNIT PRICE: Input PLU price.
5) U---UNIT: Select price unit from g, 10g, 100g, kg, Lb and Oz or PCS (g), PCS (kg), PCS (Lb) and PCS (Oz).
6) F---SHELF: Input the shelf-time of PLU: period from 0 to 365---means its unit is „day‟; period from 1000 to
9999---means its unit is „hour‟. e.g. input 60, which stands for its shelf-time is 60-day; input 1006, which
means its shelf-time is 6-hour.
7) T---TARE: Input tare (not exceeding the maximum weight).
8) B---BAR CODE: Select barcode type from 1 to 99.
9) D---DEPARTMENT: Input department code from o to 99.
10) W---PACKING WEIGHT: Input the package weight.
11) Y---Packing Type: Use key “←”“→”to select (Normal; fixed weight; fixed price; both) weight and price.
12) M---MESSAGE1: Input the selected message No. (0~12000). 0-no use this message
13) G---MESSAGE2: reserved
14) I---LABEL SELECT (Set label of corresponding PLU) Use key “←”“→”to select (DEF, D0, D1,D0D1).
15) R---Set PLU discount (-10~125).
16) S---Save PLU revision.

 PLU Data Revise

1. Press PLU key for two seconds. The display shows “PLU EDIT”, it means the system is in the state of editing
PLU.
2. Key in LFCODE when the display prompt “LLFCODE?”, and press Enter to confirm. Then the display shows
“NAME” and enter editing items: N/L/C/P/U/F/T/B/D/W/Y/M/G/I/R/S, you can use key ← and → to choose
the item you want to edit, then press Enter.
3. Key in the corresponding letter of the item to be modified, refer to the above notes, for example, key in N to
modify name and P to modify price.
4. Input the new information.
5. Press S key to save the above results. Else they are abandoned.

27
8.2 System Set
Note: This operation can be locked by password set in background PC server and is changeable as will.

1. Press the System Set for two seconds to enter the system setting state.
2. Use “←” “→” to select the desired items as follows: T/A/L//S/N/J/X/W/K/Y/D/E/F/Y/G/Q/N/W/;/@/V
Refer to the following notes.
3. Press Enter key to confirm.

Notes:
1. T---DATE: input date and time, use key “←” “→”to switch the two options. (Before you do it, you need to set
the date format)
2. A---ALIGN: Use arrow key to select one of the 17(-8~+8) values to adjust the label to the most suitable
printing state.
3. L---LABEL SELECT: Choose label type D0 or D1. (We only have such two label types presently.)
4. S---Paper: Using arrow to select paper type: label, receipt or no recycle.
5. N---DATE FORMAT: Set date format.
6. PRINT WEIGHT UNIT: This function is to set whether print the weight unit in the label.
7. PRINT PRICE UNIT: This function is to set whether print the price unit in the label.
8. J---PRICE FORMAT: Set decimal position for unit price in the label.
9. X---AMOUNT FORMAT: Set decimal position for total price in the label.
10. BARCODE SET: set barcode type; refer to Chapter 12.2 Appendix 2 for the barcode list details.
11. W---Print Time: This is to set whether print time in the label or not.
12. K---ROUND: set rounding; input a digit among 1 ~ 10, round off the last digit.
1: 0 off 1 up
2~4: Reserved
5: 4 off 5 up
6: 5 off 6 up
7: 6 off 7 up
8: 7 off 8 up
9: 8 off 9 up
10: All round off
E.g.: if you input 5, then 2.45 will be rounded to 2.5, while 2.44 will be rounded to 2.4.
13. Y---YEAR FORMAT: Set year format, use key “←” “→”to select 2 digits or 4 digits.
14. D---DENSITY: Select printing density from “0” to “5” with arrow. This scale supports print density class 0 to
5. „0‟ is the lightest one of all, and „5‟ is the thickest of all.
15. Q---PRINT DELMARK: This function is to set whether print delete mark in the label or not.
16. G---SOURCE PRICE: This function is to set whether use the original price before discount as the sale price.
17. PRINT ITEM IN WEIGHT ITEM: Two items can be printed in the „weight column‟: Weight and PCS. This
function is to set whether print Weight or PCS in the „weight column‟.
18. E---MESSAGE 1: This is to set the message no. of MESSAGE 1. Input a number among 0~250. Each number
represents different message content.
19. F---MESSAGE 2: This is to set the message no. of MESSAGE 2. Input a number among 0~250. Each number
represents different message content.
20. Set „BARCODE LINE WIDTH‟: only effective in 18-code barcode. Use arrow key to select width or narrow.
21. ;---ANTI WIND: Select anti-wind state.
22. @---IP: Input the scale IP address directly.
Note: The scale IP and PC IP should be in the same network segment, namely, the first three fields of
scale IP should be accord with PC IP. E.g. my computer‟s IP is „192.168.1.151‟, therefore, in the next
step, I should set the first three fields of scale IP to match with PC IP, namely, the first three fields of
scale IP should be „192.168.1.‟ and I set scale IP as „192.168.1.101‟.
23. V---SPEED: Set print speed. Select print speed from “0” to “7” with arrow. „0‟ is the fastest one of all, and „7‟
is the slowest of all.
24. Rebate to 23 department: Whether to set the initial 2-digit department numbers of the discount PLU barcode
as 23.
25. R---HOST IP: Input the host IP address directly, and press key [ENTER].
26. stat. mode: Whether to set the system in stat. mode. Use arrow key to select “YES” or “NO”.
28
 If you choose “YES”, the system will be in stat. mode, when you use the hotkey, the sale subtotal of this key
will be printed on label. And if you choose “NO”, you can do hotkey operation as normal.
27. stat Warnning? : Whether to set the stat. Warnning. Use arrow key to select “YES” or “NO”.
28. prn Tubtot: Press [Enter] to print the total label.
29. Prn ALL stat. plu: This operation can print stat. data of each hotkey.
30. clr stat.: Press [Enter] to clear stat..
31. Z---LABEL SELECT: This is to choose the label paper type. There are two types of label paper, one is
No-gap paper, and the other is gap paper. User key “←” “→” to select „YES‟ or „NO‟. „YES‟ for No-gap
paper, and „NO‟ for gap paper. Gap paper is the default label paper type. Only when you install the No-gap
paper into the scale, you need to set this item to „YES‟.

8.3 Function Lock

PLU edit, Discount Program and tare functions can be locked by password and password of each function is
independent and changeable. Password is set by background PC server and downloaded to every scale.
Operation on the label scale is as followings:
Note: Once you turn on the locked function, this function will be valid until the scale is warmly closed.

1. Turn on the scale.

2. Select the desired function key.
Press Discount key two seconds to enter discount function, the system prompts to input
password, then input the safe password which is set by background PC server.
Press PLU key for two second to enter PLU editing state, the system prompts to input
Turn on the
locked password, then input the safe password which is set by background PC server.
function Press System Set key for one second to enter program setting state, the system prompts to
input password, then input the safe password which is set by background PC server.
Press Tare key for one second to enter tare state, the system prompts to input password, then
input the safe password which is set by background PC server.
Press Change Price key for one second to enter change price state, the system prompts to
input password, then input the safe password which is set by background PC server.
Lock these 1. Press On/Off key for two seconds to warmly close the scale.
functions
again. 2. Press On/Off key to open the scale.

8.4 Lock Scale

You can lock the scale by password, so that other people can‟t do any operation on the scale.
Lock scale as the following method:
1. Press Password key until the word “PASSW” appears on the LCD display.
Lock the scale 2. Input the eight-digit password by numeric keyboard.
3. Press Password key and after hearing a “beep” sound to show the password has been set.
1. Turn on the scale.
Turn on the
lock casually 2. The LCD display “PASSW”.
3. Input the eight-digit password, then press Password key to turn on the lock.
1. Turn on the scale.
Turn on the 2. Press C key.
lock 3. Press Password key for two seconds until the word “PASSW” appears on the LCD display.
timelessly
4. Input the eight-digit password, then press Password key to turn on the lock.

29
9 COMMUNICATION SETUP

TO PC

NETWARE
WINDOWS NT
UNIX
POS SERVER

PC MANAGER
POS1 POS2

Note: If the HUB/SWITHCH can‟t identify the Crossover Cable when you use HUB/SWITCH to connect the
scale, please use A Straight through Cable to replace the Crossover one.

30
9.1 Handshaking Flowchart of Label Scale and Background

Link32 gathers
Sale account
from the scale

Link32 run starting

Command (201)

Is there PLU N Background is there N

Change in requires sale Link32 sends end
Background? uploading sale account i command (220)
account (120)
Y Y

Background transfers one Link32 transfers Link32 download

PLU to Link32 (110) one account to PLU change date
background (210) to label scale

LINK32 sends ACK

Command (202)
Background sends
ACK command (102)

31
Record package format:
One record package includes three aspects:
1. Package length 4Byte
2. Command 4Byte
3. Record uncertain length
Example:
Starting command: 00080201
Package length: 0008
Command: 0201
Record: no
ACK command: 00220102100000010000
Package length: 022
Command: 0102
Source: 02100000010000
From command list we can see responding command includes three aspects:
Command: 0210 which means responding to command 0210
LFCode: 000001
Error code: 0000 which means no error
Command list:
Link32->background
Code Description Type Length Remark
0201 Starting command Number 4
0202 ACK command Number 4
Command code Number 4
LFCode Number 6
Error code Number 4
0210 Link32 sends sale records command Number 4
Scale number Number 8
User ID Number 6
LFCode Number 6
Unit price Number 8 No decimal fraction mode
Weighing unit Number 1 Hexadecimal system
Total price Number 10 No decimal fraction mode
Weight Number 6 Within 15kg after logic conversion
Sell time Number 14 YYYYMMDDHH (24) NNSS
Discount Number 1 0:common, 1:change unit price, 2:change total
price
Last connect time Number 14 YYYYMMDDHH (24) NNSS
0220 Sales records sending over Number 4

32
9.2 Making procedure of connector

(1) Select a connector wire (8 pin) by length of L.

(2) Put A end of the connector wire at the edge of blade of pliers
horizontally (note: point against the baffle to ensure 12mm
peeling length), press the pliers and pull out the wire and the
peeling length is about 12mm.

1.Connection order:
green/white, green, orange/white, blue, blue/white
orange, brown/white, white.
2. line Connection order:
orange/white, orange, green/white, blue, blue/white,
green, brown/white, white.

Protruding strip Edge of cut blade

Edge of peeling blade

(3) Plug peeling end (A) into 8 PIN PHONE connector as

either Connection order above.
Make sure to plug to the end.

(4) Plug wire connector with 8 pin into the position with logo 8P
of pliers gently, then press the pliers forcefully.

(5) When process end B of connecting wire, don‟t twist

wire and keep the wire with same color in the same position.

33
 10 TROUBLESHOOTING
The scale breaks down:
1. There is no sound and no display but backlight when power is on.
Reason: Electric sparkle caused by power plugging in and pulling out destroys the ROM program in the main
board.
Treatment: Change main board, reset sequence number and download all records.
2. There is no sound and displaying „UPDATE‟ when power is on.
Reason: The same as the above.
Treatment: Download POS program to the scale again.
3. Buzzer sounds continuously and the displaying characters bounce.
Reason: The same as the above.
Treatment: The same as the above.

Question about print:

1. Paper location is normal but the printed out label is blank.
Reason: Label type sets error. It is required label type printed out by the scale should be consistent with which
downloaded from PC. Otherwise the label printed out will be blank.
Treatment: a. Adjust the scale according to the following sequence.

Enter system Enter label type Select label type

function set selection as D0 by arrow
System set L → Enter

b. Also we can adjust the software with PC. Open Link 32, input serial number of the scale, run
command function set and download this function set to the scale.
2. Printer spits out half paper or one and a half papers and paper locates abnormally.
Reason: a. Paper type sensor set error
b. Printer back photoelectric group is in wrong direction or covered by dust.
c. Photoelectric board is bad.
d. Photoelectric group of back photoelectric is bad.
Treatment: a. According to the following sequence, adjust the scale.

Enter system Enter paper Select paper type as

Set function sensor selection „Label‟ with arrow
System set S → Enter
We can also make software adjustment on computer. Open „Link32‟, set paper type as „Label‟ in function
set; download the set to the scale.
b. Check whether the back photoelectric group is gradient or covered by dust.
c. If it can‟t be resolved yet it is necessary to exchange back photoelectric group, which had better be
handled by the professional of our company.
3. Label out of printer is obscure and not dark enough.
Reason: a. Printer header is not put well.
b. Hot sensor head is dirty.
c. It is necessary to carry on voltage learning.
Treatment: a. Place printer header in suitable position
b. Clean the thermal printer with the cleaning pen attached.
4. Label printed out is half clear and half blur even blank.
Reason: a. Printer header is not put well.
b. Hot sensor header is dirty.
c. Printer header is distorted.
Treatment: a. Place printer header in suitable position.
b. Clean the thermal printer with the cleaning pen attached. The cleaning pen is an alcohol pen; please
cover it immediately after you wipe the dirty off.（Please refer to the demonstration below.）
c. If this problem can‟t be resolved yet it is necessary to change the printer. The bad printer had better
to be handled by professional of our company.

34
 Demonstration for cleaning the thermal printer head:

Clean the thermal

printer head.

① Open the thermal printer head ② Clean the thermal printer head.

[Note]：The alcohol cleaning pen is with the scale when it leave factory. Please take it out as the picture
shows below.

5. There is strange letter on the label.

Reason: LFZK has not been downloaded.
Treatment: Download LFZK again.

Questions about keyboard:

1. Display is normal but keyboard sounds continuously.

Reason: There is a short circuit in keyboard.
Treatment: change keyboard circuit.
2. Key doesn‟t sound.
Reason: a. Key wire is not inserted well.
b. Electric rubber of key press circuit board is not installed well.
c. The replaced kit is bad.
Treatment: a. Check key wire and insert it again.
b. Remove the electric rubber of key press and another location with rubber strip install again.
c. If the problem can‟t be resolved yet, the selected kit is bad.

Questions about weighing:

1. The scale can‟t weigh correctly.

Reason: a. Rubber pad, which sustains the scale pan, touched the shell (upper cover).
35
 b. Humidity or component aging or area difference makes the scale weigh incorrectly.
c. Sensor is damaged by over loading.
Treatment: a. Check whether the upper covers are buckled well. If they still knock each other, install sensor
sustainer again.
b. Study zero weight and full weight again. If it is still no use, change main board, OP board or even
the sensor.
c. Change sensor and sustainer.
Note: OP board and sensor should be returned to our company in principal if they can‟t be used.

2. Zero state is not stable.

Reason: a. It is affected by environment such as vibration, or magnetic field interference, or wind.
b. Weighing circuit is affected with damp.
Treatment: a. Remove interference.
b. Change main board.
c. If the problem can‟t be resolved. Return the whole scale to our company to repair.

3. The scale can‟t weigh.

Reason: Main board or OP board or sensor is bad.
Treatment: a. Change main board.
b. Check whether OP board is abnormal. Return the whole scale to our company.

Questions about communication:

1. The scale can‟t communicate.
Reason: a. Communication port set error.
b. Serial number of the scale has not been set.
c. Connecting head is not used correctly or Netware wire is obstructed.
d. There is some wrong with power board or main board.
Treatment: a. Confirm the correct communication port.
b. Confirm number set in Link32 is consistent with the number in the scale.
c. Confirm the Netware wire is smooth and communication connecting header is used correctly. There
are two types of communication port RS-232 which uses 9-pin or 25-pin connecting port attached
with the scale and RS-422 which uses RST-11A connecting head.
d. If the above are right, detect whether main board or power board is wrong and change the wrong
main board or power board.
2. Downloading is stopped at 1/N (n represents some number) and computer shows message
“communicate error!”
Reason: Main board is error, which may be caused by chip damage.
Treatment: Change main board or chip (ROM).

Question about display:

Display can‟t show all characters or even a character.
Reason: a. Display pole has not been installed well, which causes the display and the machine in bad contact.
b. Water flows into the base seat of display pole which makes link board short-circuit or rotten.
c. Display is damaged.
Treatment: a. Install display pole and fix the bolt.
b. Change link board or display pole.
c. Change display pole.

Other question:
Roll paper can‟t be driven by print.
Reason: maybe roll paper doesn‟t get well along with rotating axis. Or there is some matter with rotating axis.
Reason: Maybe roll paper doesn‟t get well along with rotating axis. Or there is some matter with rotating axis.
Treatment: Install the printer again which had better be processed by our company.

36
11 APPENDIX
11.1 Appendix 1: Barcode Coding List
Barcode type Department Commodity Total price Weight Checksum
number
00~09: Ean13 code, the front two codes represent department code:
00 DD (2) IIIIIIIIII (10) X X C
01 DD (2) IIIIII (6) PPPP (4) X C
02 DD (2) IIIII (5) PPPPP (5) X C
03 DD (2) IIII (4) PPPPPP (6) X C
04 DD (2) III (3) PPPPPPP (7) X C
05 DD (2) IIIIII (6) X Q.QQQ (4) C
06 DD (2) IIIIII (6) X QQ.QQ (4) C
07 DD (2) IIIII (5) X QQ.QQQ (5) C
08 DD (2) IIIII (5) X QQQQ.Q (5) C
09 DD (2) IIIII (5) X QQQQQ (5) C
10~19: Ean13code, the front two codes represent fixed code:
10 20(2) IIIIIIIIII (10) X X C
11 21(2) IIIIII (6) PPPP (4) X C
12 22(2) IIIII (5) PPPPP (5) X C
13 23(2) IIII (4) PPPPPP (6) X C
14 24(2) III (3) PPPPPPP (7) X C
15 25(2) IIIIII (6) X Q.QQQ (4) C
16 26(2) IIIIII (6) X QQ.QQ (4) C
17 27(2) IIIII (5) X QQ.QQQ (5) C
18 28(2) IIIII (5) X QQQQ.Q (5) C
19 29(2) IIIII (5) X QQQQQ (5) C
20: no print barcode
21~29: Ean13 code, the front one code represents department code:
21 D (1) IIIIIII (7) PPPP (4) X C
22 D (1) IIIIII (6) PPPPP (5) X C
23 D (1) IIIII (5) PPPPPP (6) X C
24 D (1) IIII (4) PPPPPPP (7) X C
25 D (1) IIIIIII (7) X Q.QQQ (4) C
26 D (1) IIIIIII (7) X QQ.QQ (4) C
27 D (1) IIIIII (6) X QQ.QQQ (5) C
28 D (1) IIIIII (6) X QQQQ.Q (5) C
29 D (1) IIIIII (6) X QQQQQ (5) C
30~35,40~45: 18code, the front one code represents department code
30&33 D (1) IIIIII (6) PPPPP (5) QQ.QQQ (5) C
31&34 D (1) IIIIII (6) PPPPP (5) QQQQ.Q (5) C
32&35 D (1) IIIIII (6) PPPPP (5) QQQQQ (5) C
50~52: 8 code
50 X IIIIIII (7) X X C
51 D (1) IIIIII (6) X X C
52 DD (2) IIIII (5) X X C
53 X IIIIIIII(8) X X X
54 D(1) IIIIIII(7) X X X
55 DD(2) IIIIII(6) X X X
37
36-38: 18code, the front one code represents department code, which is particular for the
batch management of live commodity.
36 D (1) LLLLLL (6) IIII (4) RR (2) QQ.QQQ (5)
37 D (1) LLLLLL (6) IIII (4) RR (2) QQQQ.Q (5)
38 D (1) LLLLLL (6) IIII (4) RR (2) QQQQQ (5)

Bar code type Department Art. No Quantity/weight Total/Unit price Check sum
79~85，87：18 code
79 DD IIIIII(6) WW.WWW PPP.PP X
80 D IIIIII(6) WW.WWW PPP.PP C
81 D IIIIII(6) WWWW.W PPP.PP C
82 D IIIIII(6) WWWWW PPP.PP C
83 D IIIIII(6) WW.WWW UUU.UU C
84 D IIIIII(6) WWWW.W UUU.UU C
85 D IIIIII(6) WWWWW UUU.UU C
87 DD IIIII(5) WW.WWW PPP.PP C

Bar code type Department Art. No Total price Quantity/weight Unit price Check sum
90~95: 18 code, the former two codes print department code
90 DD(2) IIIIII(6) WW.WWW UU.UU(4) C
91 DD(2) IIIIII(6) WWWW.W UU.UU(4) C
92 DD(2) IIIIII(6) WWWWW UU.UU(4) C
93 D(1) IIIIII(6) PPP.PP(5) UUU.UU(5) C
94 DD(2) IIIII(5) PPP.PP(5) WW.WWW C
95 DD(2) IIIIII(6) WWWWW UU.UU(4) C

Meaning of characters in the above list:

C: CHECKSUM D: Department code 2: Fixed number I: commodity number L: Live code
P: price R: discount Q: weight X: no this item
Notes:
1. Ean 13= DEPMENT+CODE+[TOTAL PRICE]+[WEIGHT]+C
Items with [] mean no this item in some coding system.
2. Usually Ean13 adopts 2 or 22 as its price barcode type while 7 or 77 as its weight barcode type.
3. CHECKSUM is calculated by the scale automatically and it is not necessary for user to input in PLU
manager.
4. The difference between 30-32 and 33-35 is the method to calculate checksum.
5. The difference between 40-45 and 30-35 is that the price in 30-35 is total price while in 40-45 is unit price.
6. 36-38 is barcode type, which can be accessed by live batch management. Commodity batch number takes up
commodity number column and commodity number takes up live code column.

38
11.2 Appendix2: Main difference between LB scale and LP scale:
Main difference between scale with pole and scale without pole:

LB serial Scale (with pole) LP Serial scale (without pole)

System set option： System set option：
R/T/D/B/P/A/L/H/O/M/S/I/J/X/K/E/F/C/Y/G/Q/N/U/V/W/Z/,/./ R/T/D/B/P/A/L/H/O/M/S/I/J/X/K/E/F/C
Two select key ← (hotkey 11), → (hotkey 10). Only one select key → (47key)
Switch key between Chinese character and English character (73) Switch hotkey between Chinese character and
English character (5)
Label editing key (key between on/off and change Press change for one minute

Confirmation key Enter (hotkey 10) Confirmation key Enter (hotkey 48)

11.3 Main difference between label scale and receipt scale

Main difference between label scale and receipt scale is that they use different sensitive paper. Their other
functions are approximately same.
Refer to chapter 4.4 for the different installing paper between table scale and receipt scale and chapter 5.13
for selecting different paper type.

39
DPSB01002EV-LS2X-09