VR723_SpecSheet.

qxd 8/5/04 8:47 AM Page 1

VR-723 Material Handler

Powerful and Productive

With exceptional break-out force, speed and versatility, this material
handler loads, digs, grades and places material. Plus, it allows the
operator to easily change out attachments without leaving the cab.
Ingersoll-Rand machines carry more weight throughout their load
zones than competitive models, while offering more responsive
handling and greater agility moving around the jobsite. Stability,
capacity, reach and strength — by every measure, these
machines excel.
VR723_SpecSheet.qxd 8/5/04 8:47 AM Page 2

VR-723 Material Handler

Specifications

METERS

FEET
C 8
25
61˚
7 D

A
50˚ C

B
6 20 B

C
40˚ 7000 A
LBS

D
B 5
15
30˚
4000 6000
4

LIFT HEIGHT
LBS LBS

20˚

MODEL VR-723 3 10
3000
LBS
5000
LBS
2 10˚
5

SIZE / DIMENSIONS 1
0˚

Overall Length (less forks) in (cm) A 201 (510) 0 0

-9˚ A
B
Overall Width in (cm) B 87.2 (222) -1 -3
D C

18 15 10 5 0 FEET
Overall Height in (cm) C 90 (230)
5 4 3 2 1 0 METERS
Wheelbase in (cm) D 112 (285) FORWARD REACH 13409396

REACH
Drive Axle to Carriage Front in (cm) E 58 (146) RATED LOAD CAPACITY
Ground Clearance in (cm) F 17 (42) Boom Retracted @ Max Angle lb (kg) 7,000 (3182)
Tread Width in (cm) G 72 (182)
Boom Extended @ Max Angle lb (kg) 7,000 (3182)
Side Leveling + / - 6°
Boom Extended @ Max Reach lb (kg) 3,000 (1364)
Shipping Weight lb (kg) 15,950 (7250)
TURNING RADIUS OPERATING SPECIFICATIONS
Inside in (cm) 54 (137) Max Lift Capacity lb (kg) 7,000 (3182)
Outside in (cm) 154 (390) Max Lift Height ft (cm) 23' 4" (712)
ENGINE Max Forward Reach ft (cm)
Make / Model Perkins / 1104C-44T turbocharged diesel From Front of Tires to 24" Load Center 13' 4" (406)
Horsepower hp (kW) 100 (74.5) @ 2,200 rpm Practical Placement Height ft (cm) 21' (640)
Torque ft-lb (Nm) 304 (412) @ 1,400 rpm Max Reach Practical Placement Height ft (cm) 7' 2" (219)
TRANSMISSION Max Vertical Reach Below Grade in (cm) 15" (37)
Type Hydrostatic Max Reach @ Max Height ft (cm)
Two Driving Modes Working / travel From Front of Tires to 24" Load Center 4' 6" (137)
Working Speed (fwd & rev) mph (km/h) 0 – 4.6 (0 – 7.39) Break-out Force lb (kN) 11,885 (53)
Travel Speed (fwd & rev) 0 – 15.4 (0 – 25) Drawbar Pull lb (kN) 10,341 (46)
DRIVE AXLES BOOM
Front & Rear All-wheel drive
Boom Type 2-Stage
Type Planetary steering
Boom Angles Up: 62° Down: -9°
BRAKES Extend Speed 6.9 seconds
Service Internal wet disc
Parking Internal — spring applied, hydraulic release Retract Speed 5.6 seconds
Boom Lift Speed 7.5 seconds
TIRES
Make / Model Titan / Lift Rigger II Boom Lower Speed 4.6 seconds
Front & Rear 400 / 70 x 20 — 166A2 Carriage Rotation 154°
Ballast Not required Note: Capacities are to ASME B56.6-2002

STEERING OPTIONS / ACCESSORIES

Three Modes 2-wheel, 4-wheel or crab ■ Air-conditioned cab
ELECTRICAL ■ Rotating beacon
Negative Ground 12V
Alternator 100A
Battery 900A
Back-up Alarm 102 dBA
Product improvement is a continuing goal at Ingersoll-Rand.
Designs and specifications are subject to change without notice or obligation.

www.irco.com
(877) IR BRAND © 2004 Ingersoll-Rand Co. Form 07-0032
Printed in USA 05-04