ORDER NO.

VED1110409CE
D10

LCD Projector

Model No. PT-AR100U

PT-AH1000E
PT-AR100EA
PT-AR100EH

© Panasonic Corporation 2011. Unauthorized

copying and distribution is a violation of law.
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this service manual.

WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It dose not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.

WARNING : Use UV Radiation eye and skin protection during servicing

CAUTION
Lithium Battery
Risk of explosion if battery is replaced by an incorrect type,
Replace only with the same of equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.

Precaution
If using of this projector at high altitudes (above 1,400m), set HIGHT ALTITUDE MODE to “ON”.
(Refer to “PROJECTOR SETUP menu” in Operating Instructions.)
Failure to observe this may cause malfunctions. Never use this projector at an altitude of 2,700m or higher.
Using this projector at high altitude, consult your dealer or Authorized Service Center about preparations.

About lead free solder (PbF)

This projector is using the P.C.Board which applies lead free solder.
Use lead free solder in servicing from the standpoint of antipollution for the global environment.
Notes:
・ Lead free solder: Sn-Ag-Cu (tin, silver and copper) has a higher melting point (approx. 217°C) than standard solder. Typically the melting point
・ is 30~40 °C higher. When servicing, use a high temperature soldering iron with temperature limitation function and set it to 370 ± 10 °C.
・ Be precautious about lead free solder. Sn-Ag-Cu (tin, silver and copper) will tend to splash when heated too high (approx. 600°C or higher).
・ Use lead free solder for the P.C.Board (specified on it as “PbF”) which uses lead free solder. (When you unavoidably use lead solder, use lead
・ solder after removing lead free solder. Or be sure to heat the lead free solder until it melts completely, before applying lead solder.)
・ After soldering to double layered P.C.Boards, check the component side for excess solder which may flow onto the opposite side.

About the identification of the lead free solder P.C.Board.

For the P.C.Board which applies lead free solder, the symbol as shown in the figure below is printed or stamped on the surface
or the back of P.C.Board.

or
For US
IMPORTANT SAFETY NOTICE
There are special parts used in Panasonic LCD Projectors which are important for safety. These parts are shaded on the schematic
diagram. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire, or other
hazards. Do not modify the original design without permission of PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY.

WARNING:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, The user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

CAUTION : Any unauthorized changes or modifications to this equipment will void the users authority to operate.

2
TABLE OF CONTENTS

■ COVER PAGE
1. Safety Precautions
2. Specifications

■ SECTION 1 <Service Information>

1. The name of each part
2. OSD Menu Navigation
3. Extend mode (EXT OPTION menu)
4. External Control
5. Notification for service operation
6. Troubleshooting

■ SECTION 2 <Disassembly Procedures>

1. Parts Location
2. Disassembly Instructions

■ SECTION 3 <Adjustment>
1. Adjustment items and procedure
2. Microprocessor update procedure

■ SECTION 4 <Schematic Diagrams>

1. Block Diagram
2. Interconnection Block Diagram
3. Schematic Diagram
4. Circuit Boards Diagram

■ SECTION 5 <Exploded Views & Replacement Parts List>

1. Exploded Views
2. Replacement Parts List

3
1. Safety Precautions
1.1. General Guidelines
- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper
case removed and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated
or damaged by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation
R-C combinations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.

1.2. Leakage Current Check

1. Prepare the measuring circuit as shown in Fig.1.
Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75mA or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer
because of a possibility of an electric shock.

Fig. 1 Fig. 2

Table. 2

1.3. UV Precaution and UHM Lamp Precautions

- Be sure to unplug the power cord from the power outlet when replacing the lamp.
- Because the lamp reaches a very high temperature during its operation, wait until it cools completely when replacing
the Lamp Unit.
- The lamp emits small amounts of UV-radiation, avoid direct-eye contact with the light.
- The lamp unit has high internal pressure. If improperly handled, explosion might result.
- Because the high pressure lamp involves a risk of failure, never touch the lamp wire lead during the service.

Fig. 3

4
2. Specifications

*1 : Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*2 : For details of video signals that can be projected using this projector, refer to “List of compatible signals” of
Operating Instructions.

5
*1 : HD/SYNC, and VD terminals do not accept tri-level sync signals.
*2 : Average value. Weight varies for each product.

6
SECTION 1

< Service Information >

Model No. PT-AR100U / AR100EA / AR100EH
PT-AH1000E

CONTENTS

1. The name of each part　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-2

1.1. Projector body
1.2. Control panel
1.3. Rear terminals
1.4. Remote control
2. OSD Menu Navigation　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-4
3.Extend mode (EXT OPTION menu) ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-5
3. 1. Procedure to open / close "EXT OPTION" menu
3. 2. EXT OPTION Menu and Functions
4. External control　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-7
4. 1. Connecting exsample
4. 2. Pin assignment and signal
4. 3. Communication condition
4. 4. Specification of cable communication
4. 5. Basic format
4. 6. Control commands
4. 7. Inquiry commands
5. Notification for service operation　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ INF-10
5. 1. Before service operation
5. 2. Service
5. 3. Replacement of consumable parts
6. Troubleshooting　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 　 INF-14
6. 1. Shutdown system
6. 2. Troubleshooting flow
1. Name and function
　1.1. Projector body

INF - 2
　1.2. Control Panel

　1.3. Rear terminals

　1.4. Remote control

INF - 3
2. OSD Menu Navigation
 MENU MENU

Note : The default settings may be different depending on the picture menu

INF - 4
3. Extend mode (EXT OPTION menu)
This projector has extend mode "EXT OPTION" menu in addition to standard on-screen menus.
 This mode has Self-Check function, Test Pattern and other functions for Service.

　3. 1. Procedure to open / close "EXT OPTION" menu.

1. When the projector is power ON, press "POWER" button on the main unit or remote control unit to display
"POWER OFF" confirmation screen.
2. Press the "  " button to select "CANCEL" in the "POWER OFF" confirmation screen.
3. On the main unit or remote control unit, press the buttons in order of " ▲ ", " ▼ ", " ▲ ", " ▼ " and "ENTER".
4. When "MENU" button is pressed at the "EXT OPTION" mode, Extend-mode is closed.

　3. 2. EXT OPTION Menu and Functions

1.FAN FULLMODE
EXT OPTION ・Setting the cooling fan motor rotation speed.
Switching ON "FAN FULLMODE", the rotation level of the
1. FAN FULL MODE OFF fan becomes high-speed rotation (fixed). Moreover, when
2. AUTO SETUP NORMAL "FAN FULLMODE" is ON, changing "HIGH ALTITUDE
3. SELF CHECK MODE" in OPTION menu becomes impossible (setting
4. STATUS FAN FULLMODE is given priority more than HIGH
5. FLICKER ADJUST ALTITUDE MODE).
2.AUTO SETUP
・Setting AUTO SETUP mode.
- NORMAL: Dot clock is adjusted strictly.
- SPECIAL: Dot clock is adjusted roughly.
* Do not usually change initial setting (NORMAL).

3.SELF CHECK
・The content of self checking are displayed.
(13) (1) - Software Version (MM : Main microprocessor, F:FPGA )
(1) (14) * FPGA (Field Programmable Gate Array)
(2) (2) - Input signal Display
(3) (15) ( [NO-SYNC] is displayed when there is no input signal).
(3) - Input Horizontal/Vertical signal frequency
(4) (For the RGB/YPBPR Input only)
(5) (16) (4) - The temperature abnormality check
("NG" is displayed for any abnormality)
(6)
(5) - Temperature around the air intake port/exhaust port and

(17) Filter sensor 　(deg C/A/D conversion value)

(7)
(6) - Filter sensor Difference Correction (A/D conversion) Value
(7) - Rotation check of Intake fan / Lamp fan / Iris fan
(8)
(Displays "NG" when Fan is abnormal condition)
(9) (18) (8) - Iris condition check (Abnormal condition = "NG")
(10) (9) - Lamp condition check (Abnormal condition = "NG")
(11) (19) (10) - Lamp cover installation check (Abnormal condition="NG")
(11) - Displays the projector cumulative usage time
(12) (20)
(12) - Cumulative usage time (actual time) and Number of
LAMP ON times
"OK" display becomes red characters when shutting "Current number : Last reset : Reset of last but one"
down because abnormality happened time.
(13)- Displays the serial number of the projector.
(14)- Software Version (SM : Sub microprocessor, IM : IRIS control microcomputer)
(15)- Gamma and Color Unevenness correction data check (Whether data are stored in the flash ROM)
(16)- Thermo sensor (Intake Air / Exhaust Air / Filter Air) measurement value when thermal shutdown
(deg C/A/D conversion value)

INF - 5
 (17)- Rotation check of Exhaust fan and Power fan (Displays "NG" when Fan is abnormal condition)
* When detected abnormal temperature around the air intake port / air exhaust port / LCD block,
TEMP indicator turned on. If arriving at the critical temperature, the power supply will shut down
automatically (thermal shutdown) and the indicator will flash.

(18)- Judgment for Replacement Time of Lamp (Cumulative Usage more than 2000H is "NG")
* Warning of the lamp cumulative usage time and shutdown use the conversion time for LAMP POWER "NOMAL".
(19)- The number of times that carried out reset of "LAMP RUNTIME"
(20)- Cumulative usage time (conversion for LAMP POWER "NOMAL" time) and Number of LAMP ON times
"Current number : Last reset : Reset of last but one"

4.STATUS
・Display version of each software and each data.

5.FLICKER ADJUST
・To enter the flicker adjustment mode.
Note: If replacing the optical parts (Optical block) or A-P.C.Board, adjust to flicker is minimum according to the
"SECTION 3 Flicker adjustment".

INF - 6
4. External Controls of SERIAL Connection
The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification,
so that the projector can be controlled by a personal computer which is connected to this connecter.

4. 1. Connecting exsample
Interface at the rear side
Personal computer

D-Sub 9p (Male)

Note
Interface cable is not a standard accessory. Please purchase locally.

4. 2. Pin assignment and signal

Pin Name Signal

D-sub 9pin(Female) ① - NC
Outside view ② TXD Transmitting data
③ RXD Receiving data
④ - ＮＣ
⑤ GND Ground
⑥ -
Connented each other
⑦ CTS
inside
⑧ RTS
⑨ - NC

4. 3. Communication condition
Signal level RS-232C standard
Synchronization Asynchronous
Baud rate 9 600 bps
Parity None
Character length 8 bit
Stop bit 1 bit
X Parameter None
S Parameter None

4. 4. Specification of cable communication

In case of connecting to PC
1 NC NC 1
2 2
3 3
4 NC NC 4
Personal Computer side
Projector side 5 5
(DTE spec)
6 DSR NC 6
7 7
8 8
9 NC NC 9

INF - 7
4. 5. Basic format
The transmission from Personal Computer starts with STX, Command, Parameter and EXT are sent in order.
Parameters can be added as necessary.

STX Command ： Parameter ETX

Start byte(02h) 3 bytes 1 byte 1byte - 4 bytes End (03h)

・The projector can not receive any command for 10 seconds after the lamp is switched on. Wait 10 seconds before
sending the command.
・If sending multiple commands, check that a response has been received from the projector for one command
before sending the next command.
・When a command which does not require parameters to be sent, the colon (:) is not required.
・If an incorrect command is sent from the personal computer, the ER401 command will be sent from the projector
to the personal computer.

4. 6. Control commands
Refer to Operating Instructions of PT-AR100 / PT-AH1000.

INF - 8
4. 7. Inquiry commands
Refer to Operating Instructions of PT-AR100 / PT-AH1000.

INF - 9
5. Notification for service operation
5. 1. Before service operation
5. 1. 1. LCD panel
1. The display unit of this projector comprises three LCD panels. Although an LCD panel is a product of high precision
technology, some of the pixels on the projected image may be missing or constantly lit.
Please note that this is not a malfunction.
2. Displaying a still image for a longer time may result in an after-image on the LCD panels.
If this happens, display the all white screen in the test pattern for an hour or more.

5. 1. 2. Lamp unit
* Lamp unit as an optional accessories, distribution through commercial channel.

Replacement lamp unit : ET-LAA110

* Do not use any other lamp unit than indicated above.

1. Be careful for handling the lamp because it is made of glass and might be
exploded by hitting hard object or fall in down.
2. Philips driver is required for replacing the lamp.
3. When replacing the lamp, make sure to grasp the handle portion of the lamp unit.
4. The lamp might be exploded. Be careful for the case that the blown glasses are scattered around.
The replacement operation should be done with the highest care.
When the projector is set on the ceiling, make sure not to work just under the lamp unit or not to be closer to the lamp.
5. When throwing the lamp away, consult local municipalities about the way to do.
[Attention]
* Please read carefully the page 'CAUTIONS FOR THE SAFETY', 'BEFORE USING', 'CHECK AND REPLACEMENT OF
PARTS' on the instruction book to know about lamp unit, how to use lamp and how to replace the lamp unit.

5. 1. 3. Air filter unit

* Clean the Air filter after every 100 hours of usage.
* A replacement air filter kit (TXFKN01RYNZP) is provided with a replacement lamp unit, ET-LAA110.

Air Filter Kit

(TXFKN01RYNZP)

1. If the air filter is excessively dirty, the internal temperature of the projector increases and may cause malfunction.
2. Do not use the projector without attaching the air filter.
3. The air filter should be replaced when cleaning is ineffective and when replacing the lamp unit.

5. 1. 4. Repair operation
1. When electrifying the projector for the check and adjustment with top case taken off, the strong light emits from
the lighting cover and its around.
Wear the anti -ultraviolet rays glasses and shade.
2. While the fan is working, do not pull the plug out nor disconnect the breaker.
* When the monitor of power supply lamp turns red and the fan stops, disconnecting can be done.
3. Repair should be done with the power supply off.
* When replacing the print board, the internal electrical parts can be broken by the static electricity of clothes or
human body. Be careful of static electricity and wear the anti-static electricity globes.
4. After finishing the repair, check whether it works properly or not.
5. Check the image with 10 steps or gray scales that can show the gradation and perform self-check.

INF - 10
 5. 2. Service
5. 2. 1. Supporting Methods
The basic service policy is shown below.
Service method Applied parts
・ Analyses block (* Specified components are replaced)
・ Optical Block (with projection lens)
Block replacement *Projection lens can not be separated from optical block.
P.C.Board replacement ・ K1/K2-P.C.Board (*Specified components are replaced)
・ P-P.C.Board ・ B-P.C.Board
・ H-P.C.Board ・ M1/M2/M3-P.C.Board
Individual parts supply.
 Other electrical parts / Other mechanical parts
Individual parts replacement on
5. 2. 2. When change a A-P.C.Board
If replacing A-P.C.Board (assembly), read the ROM data from the old P.C.Board and write it in the new one according to
the section 3. "Adjustment".
* Down load the adjustment software from our Projector service web site.
* At this time, if the readout from the old P.C.Board does not succeed, remove IC1301 and IC1305 from the old P.C.Board
and install them on the new one.
After replacing A-P.C.Board (assembly), perform each adjustment in reference to SECTION 3 "Adjustments".

5. 2. 3. Identification for type A and type B of Optical block Flexible cable of LCD panel (G)
Please confirm described No. on flexible cable of LCD panel (G).
- L3C07U-86G13 → Select "Type A" of optical block.
- L3C07U-85G13 → Select "Type B" of optical block.

　5. 3. Replacement of consumable parts

[Attention]  When replacing the consumable parts, please make sure that the main power is OFF and power cable is
disconnected.
5. 3. 1. Replacement timing for lamp unit
1. Confirm the lamp usage hours with "LAMP RUNTIME" of "OPTION menu", and replace it periodically.
2. The replacement guideline is every 2000 hours, but it may turn off before 2000 hours depending on lamp's individual
characteristic, usage condition, environment and etc. Earlier replacement is recommended.
3. When the lamp is kept using after 2000 hours without replacement, it automatically turns off after 10 minutes for
avoiding failure.
Lamp time On screen " REPLACE LAMP " LAMP indicator
The message is displayed for 30 seconds. If you press any button
Over 1800 hours
within the 30seconds, the message disappears. Illuminates red, including when
in standby mode.
Over 2000 hours The message is displayed until you press any button.

* 2000 hours of use is a rough guideline, but this is not a guarantee.

5. 3. 2. Replacement procedure for lamp unit

1. Confirm that the lamp unit is cooled down completely.
(More than 1 hour has passed after main power is off.)
2. Open the top cover in the direction of the arrow. Top cover
3. Lamp cover fixing screw is loosened all the way and
remove "Lamp cover".

Lamp cover
lamp cover fixing screws

INF - 11
 4. Use a Phillips screwdriver to unscrew the lamp unit fixing screws (2 screws) until loose.
5. Hold the handle of the lamp unit and with the lamp unit lock held in the direction of the red arrow,
carefully pull it out of the projector unit in a vertical motion.
Lamp unit fixing screws

Handle

Lamp unit lock

6. Insert the new lamp unit in correct direction. Tighten the two lamp unit fixing screws securely with a Phillips screwdriver.
* Press down on the A part firmly when inserting the lamp unit.
7. Attach the lamp cover, and tighten the two lamp cover fixing screws securely with Phillips screwdriver.
8. Close the top cover of the projector.

5. 3. 3. Reset procedure of the lamp use time

1. Insert the power plug into a power outlet, and press the <ON> side of the <MAIN POWER> switch to turn on the power.
2. Press the <MENU> button to display the menu screen, and select [OPTION] with the ▲▼ buttons.
3. Press the <ENTER> button, and select [LAMP RUNTIME] with the ▲▼ buttons.
4. Hold the <ENTER> button down for 3 seconds.
5. Select [OK] with the t u buttons and then press the <ENTER> button.
* LAMP RUNTIME is reset to “0” and the projector prepares to power off.
After a short while, the projector enters power off (standby) mode.

5. 3. 4. Air filter unit maintenance

1. If too much dust accumulates in the air filter the internal temperature of the projector cannot be maintained
at the normal level.
2. Confirmation message is displayed on the screen, and at the same time <TEMP> illuminates red.
The power is cut off automatically after a while.

5. 3. 5. Cleaning procedure for Air filter unit

1. Using a Phillips screwdriver to turn the fixing screw of the air filter cover until loose and remove the cover.

Air filter cover fixing screws

Air filter cover

2. Hold the grips on the air filter unit, and remove the unit towards arrow.

Air filter unit

Grips

INF - 12
 3. Vacuum the dirt and dust, from the air filter unit.
* Do not wash the air filter unit.

5. 3. 6. Replacement procedure for Air filter kit

1. Press the protrusions of air filter unit removed from the projector in the direction of the arrow and remove
the air filter frame.

Air filter frame

Protrusions
2. Replace the Air filter kit (air filter/electrostatic filter).
* Ensure you attach the electrostatic filter and air filter in the correct order.

Air filter frame

Air filter (black)

Electrostatic filter (white)

Air filter case

5. 3. 7. Caution for the inorganic polarizing plate ( IN(B) /OUT(B) /OUT(G) )

Inorganic parts have been introducing for the elongation of the parts life.
However scrupulous attention is needed on the handling of the parts for the inorganic polarizing plate and panel.

Polarizing plate/IN (B)

Polarizing plate/OUT (B)

Polarizing plate/OUT (G)

* Do not touch the surface of polarizing plate and panel directly by the hand.
- Must use a tweezers, fingerstall or clean gloves.
- Must catch the edge of polarizing plate and LCD panel.
* Do not clean/rub the surface of them with a cloth or a swab.
- Clean by an air blow.

INF - 13
6. Troubleshooting
6. 1. Summary of shut down system
When the abnormality of the lamp and the abnormality of the fan occurred, possess a shut down function to make a
standby state for safety promptly.
Monitor LED indication Shut down Detection Presumed Factor OSD Warning Indication

Power fuse Blown out of the fuse

－
=> 8A 250V (with some reason)

Thermal fuse Blown out of the fuse

－
=> More than 105 degrees C (with some reason)

IIC bus
Communication line is disconnection
=>FPGA initialized error －
in A-P.C.Board.
=>Communication error
No flashing or blinking

Connector is disconnected
No FAN sense signal －
Fan abnormal

Each FAN sense signal:

=> Rotation speed is slower
Fan speed abnormal －
than 50% of target for
more than 10 seconds.

IRIS sense signal

Iris unit abnormal
=> Unresponsiveness is more －
Iris drive circuit abnormal
than 1 minute

Interlock SW
All indicator Illuminating Lamp unit cover is not installed. －
=> Abnormal :OFF

Intake air temperature sensor: Connection problem with Intake air

temperature sensor. －
=> Under -36 degrees C
Faulty temperature sensor.

Exhaust air temperature Connection problem with Exhausting air

sensor: temperature sensor. －
=> Under -36 degrees C Faulty temperature sensor.

More than 41 degrees C

TEMP indicator Intake air temperature sensor: Intake air temperature error =>“TEMPERATURE WARNING"
High temperature of environment
Flashing red => More than 43 degrees C lower than 39 degrees C
Intake air window is closed
=> Warring cancel
More than 77 degrees C
Exhaust air temperature Exhausting air temperature error: =>“TEMPERATURE WARNING"
sensor: Closed ventilator
lower than 75 degrees C
=> More than 79 degrees C High altitude mode is not on.
=> Warring cancel
Filter air temperature
Filter clogging
sensor:
Closed Intake "Air filter cleaning"
=> More than threshold
High altitude mode is not on
** degrees C

Lamp status Failed lamp ON,

LAMP indicator lamp abnormal condition
=> Lamp is off during the status －
Flashing red Ballast block faulty,
other than normal one Hot restart
Lamp hours
=> Over 2000 hours Over 1800 hours
LAMP LED Lights Lamp usage hour is over the guideline.
(Shouts down after 10 => “Replace lamp"
minutes.)
Value "**" is changed by "Lamp mode", or "Fan mode" and "Setting attitude"

INF - 14
SECTION 2

<Disassembly Procedures>
Model No. PT-AR100U / AR100EA / AR100EH
PT-AH1000E

CONTENTS

1. Parts Location　　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIS-2

1. 1. Electrical Parts Location (P.C.Board)
1. 2. Electrical Parts Location (Fan)

2. Disassembly Instructions　　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIS-3

2. 1. Flowchart for Disassembly
2. 2. Removal of Top Cover
2. 3. Removal of A-P.C.Board
2. 4. Removal of Optical Block / Analysis Block
2. 5. Removal of M3 P.C.Board
2. 6. Removal of PBS Array / Iris Unit
2. 7. Removal of P-P.C.Board / B-P.C.Board
2. 8. Removal of K1-P.C.board / K2-P.C.Board
2. 9. Remonal of M2-P.C.Board
1. Parts Location
　1. 1. Electrical Parts Location (P.C.Board）
H

B
P
A

K1
V
K2
M2 M1

S
M3

Board Name 　Function summary Board Name 　Function summary

Image processing system
A M3 Temp sensor (Air flow)
/ Microcomputer
S Control Panel B Ballast power / Ballast control

V Indicator LED P Power supply (DC-DC)

H Iris posistion sensor K1 AC Inlet

M1 Temp sensor (Intake) K2 Line Filter

M2 Temp sensor (Exhaust)

1. 2. Electrical Parts Location (Fan)

Power Fan

Lamp Fan

Intake Fan

Exhaust Fan

Iris Fan

DIS-2
2. Disassembly Instructions
2. 1. Flowchart for Disassembly
* Before Disassembly the projector, turn off the POWER switch and disconnect the power plug from the wall outlet.
* To assemble, reverse the disassembly procedures.
* When tore off sticky tapes, please use a new thing without reusing it on the occasion of assembling.
* Description of the illustration may be different from the real.

Completed Product

2. 2. Removal of Top Cover

2. 3. Removal of A-P.C.Board

Removal of Optical Block

2. 4.
/ Analysis Block

2. 5. Removal of M3 P.C.Board

Removal of
2. 6.
PBS Array / Iris Unit

Removal of K1-P.C.board
2. 8.
/ K2-P.C.Board

Removal of P-P.C.Board
2. 7.
/ B-P.C.Board

2. 9. Remonal of M1-P.C.Board

DIS-3
2. 2. Removal of Top Cover
1. Remove the Top panel.
Top panel
1) Hold the top cover as shown in the diagram.
2) While pushing the arm in the direction of the arrow
(inside projector), pull out from the groove.

* Attaching the top panel

1) Hold the top cover as shown in the diagram.
2) Align the hinge with the support.
3) while pushing the arm in the direction of the arrow
(inside projector) push it into the groove.

2. Unscrew the 9 screws on the top side and 1 screw on the rear side.

Top cover

2. 3. Removal of A-P.C.Board
1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover".
2. Unscrew the 5 screws and remove the A-P.C.Board block.

A-P.C.Board block

3. Unscrew the 2 screws and remove the Terminal cover and Shading sheet.

Shading sheet
Terminal cover

A-P.C.Board

DIS-4
2. 4. Removal of Optical Block / Analysis Block
1. Remove the A-P.C.Board block according to the steps 1 through 2 in the section 2.3. "Removal of A-P.C.Board".
2. Loosen the 2 screws and remove the Lamp unit.
3. Unscrew the 1 screw and remove the V-P.C.Board.
4. Unscrew the 3 screws and remove the Front cover.

Front cover

V-P.C.Board

5. 1) Unscrew the 1 screw and remove the earth cable.

2) Unscrew the 2 screws and remove the Optical block.

Earth cable
Optical Block (with a lens unit)

* There is not enough space between

the Analysis block and Optical block.
Be careful not to damage nor dirty
precision components (LCD panel,
incidence polarizer, etc.) when
removing.

6. Unscrew the 4 screws and remove the Analysis block.

Analysis block

* The incidence polarizer is installed in

the Analysis block.
Be careful not to shift the installation
position nor damage it.

DIS-5
2. 5. Removal of M3 P.C.Board
1. Remove the Analysis block according to the section 2.4. "Removal of Optical Block / Analysis Block".
2. Unscrew the 1 screw and remove the A-P.C.Board earth metal.
3. Unscrew the 3 screws and remove the Intake duct.

A-P.C.Board
earth metal

Intake duct

Intake duct fixing metal

4. Unscrew the 1 screw and remove the M3-P.C.Board.

M3-P.C.Board

2. 6. Removal of PBS Array / Iris Unit

1. Remove the Analysis block according to the section 2.4. "Removal of Optical Block / Analysis Block".
2. Unscrew the 5 screws and remove the Analysis case (upper).
* Can be removal of PBS Array.

* The incidence polarizer is installed in

the Analysis case (upper).
Be careful not to shift the installation
position nor damage it.

Analysis case (upper)

3. Unscrew the 1 screw and remove the Integrator hold spring.

Integrator hold spring

PBS array

DIS-6
 4. Unscrew the 2 screws and remove the Iris unit.

Iris unit

2. 7. Removal of P-P.C.Board / B-P.C.Board

1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover".
2. Loosen the 2 screws and remove the Lamp unit.
3. Unscrew the 3 screws and remove the Lamp house.

Lamp house

4. Unscrew the 1 screw and remove the Lamp socket.

Lamp socket

5. Unscrew the 5 screws and remove the Ballast block.

* Remove the P2 connector.

Ballast block

DIS-7
6. Unscrew the 2 screws and remove the P-P.C.Board.

P-P.C.Board

7. Unscrew the 1 screw and remove the Power duct.

Ballast block

Power duct

8. Unscrew the 2 screws and while pressing to shut each hook of the 2 resinous stands, remove the B-P.C.Board.

B-P.C.Board

B-P.C.B

Resinous stands

Power-Fan

Note:
1) Be careful the installation direction of Power-Fan.
2) Roll the Fan cable one turn on core.

DIS-8
2. 8. Removal of K1-P.C.board / K2-P.C.Board
1. Remove the A-P.C.Board earth metal according to the steps 1 through 5 in the section
2.4. "Removal of Optical Block / Analysis Block".
2. Unscrew the 4 screws and remove the Optical Block and Analysis Block.

Optical Block + Analysis Block

3. Unscrew the 3 screws and remove the Lamp house.

Lamp house

4. Unscrew the 2 screws and remove the Lamp duct base.

Lamp duct base

5. Unscrew the 2 screws and remove the K-P.C.Board block.

K1-P.C.Board

K-P.C.Board block

K2-P.C.Board

DIS-9
2. 9. Remonal of M1-P.C.Board
1. Remove the Top Cover according to the section 2.2 "Removal of Top Cover".
2. Unscrew the 1 screw and remove the V-P.C.Board.
Front cover
3. Unscrew the 3 screws and remove the Front cover.

V-P.C.Board

4. While pressing to shut each hook of the Adjuster leg, remove the Adjuster leg (lens side).

Adjuster leg

5. Remove the Bottom cover (R).

Bottom cover (R)

6. Unscrew the 1 screw and remove the M1-P.C.Board.

DIS-10
SECTION 3

< Adjustments >

Model No. PT-AR100U / AR100EA / AR100EH
PT-AH1000E

CONTENTS

1. Adjustment items and procedure　　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-2

1. 1. Flicker Adjustment
1. 2. Data Transfer
1. 3. Model Information Setup
1. 4. Model Information Setup
1. 5. Clog Sensor calibration

2. Microprocessor update procedure　　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ADJ-7

2. 1. Update by serial Terminal Cnnection
1. Adjustment item and a procedure
When the following components in this projector are replaced, adjustments are required. Adjust each item according
to the table below.
Adjustment Items Replaced parts Remarks

1. 1. Flicker Adjustment OPTICAL BLOCK / A-P.C.Board

Save data to a PC before A-P.C.B exchange and
1. 2. Data Transfer A-P.C.Board
write it into a new A-P.C.B.
1. 3. Model Information Setup A-P.C.Board

1. 4. Serial Number Setup A-P.C.Board

1. 5. Clog Sensor Calibration A-P.C.Board / M3-P.C.board

1. 1. Flicker Adjustment
1. 1. 1.Adjustment Procedure
1. Select "FLICKER ADJUST" on "EXT OPTION" menu and press "ENTER" button on the main unit or remote control unit.
2. "DESK setting (blue)" is displayed when entering the adjustment mode.
3. Setting value is increased and decreased with the right-arrow "  " and left-arrow "  " buttons.
- Adjust the setting value to minimize the flicker on the screen.
4. The pattern (adjustment display) is switched with the up-arrow " ▲ " and down-arrow " ▼ " buttons.
- There are 6 patterns of "DESK setting (blue)", "DESK setting (red)", "DESK setting (green)", "CEILING setting (blue)",
"CEILING setting (red)" and "CEILING setting (green)".
5. Press "MENU" button on the main unit or remote control unit.
- When "MENU" button is pressed, the setting value at that time is saved into this projector and the adjustment
mode is canceled.

1. 2. Data Transfer
1. 2. 1. Required equipments
1. PC : Use to transfer the backup data.
2. Communication cable : D-sub 9pin (male/emale RS-232C straight)
3. Software : ［Service ORCA10.exe］Adjustment software is downloaded from the projector service homepage.

Computer Projector
1. 2. 2. Preparation
1. Connect the RS-232C termanal of projector
and PC with a RS-232C cable.

RS-232C cable (Streight)

1. 2. 3. Backup the Data (It is before A-P.C.Board exchange)

1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
2. Start up service software ［Service ORCA10.exe］ with a computer.
3. Select language and click the [ OK ] button.

4. 1) Select the Serial Port of the computer.

2) Select a model number.
(Case of AH1000, select the AR100.) ②
①
3) Click the [ Data ] button.
③

ADJ - 2
 5. 1) Click the [ Reception ] button of Micom Data.
2) Select the save place and click the [ Save ] button.
3) When the progress bar reaches the right-side end, the save of data is completion.
4) Save the Gamma Data, Uniformity Data and the Color Management Data in the same procedure of 1-3.

1. 2. 4. Restore the Backup EEPROM Data (After A-P.C.Board exchange)

1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
2. Start up service software ［Service ORCA10.exe］ with a computer.
3. Select language and click the [ OK ] button.
4. 1) Select the Serial Port of the computer.
2) Select a model number.
(Case of AH1000, select the AR100.) ②
①
3) Click the [ Data ] button.
③

5. 1) Click the [ Transmission ] button of Micom Data.

2) Select the file and click the [ OPEN ] button.
3) When the progress bar reaches the right-side end, the transmission of data is completion.
4) Restore the Gamma Data, Uniformity Data and the Color Management Data in the same procedure of 1-3.

6. If the restoration of data is completed, turn the MAIN POWER off then MAIN POWER on.

ADJ - 3
1. 3. Model Information Setup
1. 3. 1. Required equipments
1. PC : Use it as adjustment use.
2. Communication cable : D-sub 9pin (male/emale RS-232C straight)
3. Software : ［Service ORCA10.exe］Adjustment software is downloaded from the projector service homepage.

1. 3. 2. Preparation
1. Connect the RS-232C termanal of projector Computer Projector
and PC with a RS-232C cable.

RS-232C cable (Streight)

1. 3. 3. Setting method
1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
2. Start up service software ［Service ORCA10.exe］ with a computer.
3. Select language and click the [ OK ] button.
4. 1) Select the Serial Port of the computer.
2) Select a model number.
(Case of AH1000, select the AR100.)
3) Click the [ Adjustment ] button.
① ②

5. Click the [ Model Info Setup ] button.

6. Put a checkmark in an applicable model, and click the [OK] button.

ADJ - 4
1. 4. Serial Number Setup
1. 4. 1. Required equipments
1. PC : Use it as adjustment use.
2. Communication cable : D-sub 9pin (male/emale RS-232C straight)
3. Software : ［Service ORCA10.exe］Adjustment software is downloaded from the projector service homepage.

1. 4. 2. Preparation
1. Connect the RS-232C termanal of projector Computer Projector
and PC with a RS-232C cable.

RS-232C cable (Streight)

1. 4. 3. Setting method
1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
2. Start up service software ［Service ORCA10.exe］ with a computer.
* Please close another software before using the "Service software".
3. Select language and click the [ OK ] button.
4. 1) Select the Serial Port of the computer.
2) Select a model number.
(Case of AH1000, select the AR100.)
3) Click the [ Data ] button.
②
①

5. Click the [ Set up ] button of Serial Number.

6. Input the product serial number, and click the [ Send ] button.

ADJ - 5
1. 5. Clog Sensor Calibration
Clog sensor circuit is calibrated.
* This operation should be done with the main body is completely assembled and set on the floor and the adjuster
legs are set in the main body. (A state of Disassembly, cannot correct it.)
* Confirm that there is no heating equipments, flow out of air conditioner, obstacles for air intake and exhausting
for the projector.
* Please carry it out after “Data Transfer” of Micom Data.
1. 5. 1. Required equipments
1. PC : Use it as adjustment use.
2. Communication cable : D-sub 9pin (male/emale RS-232C straight)
3. Software : ［Service ORCA10.exe］Adjustment software is downloaded from the projector service homepage.
1. 5. 2. Preparation Projector
Computer
1. Please clean the air filter before starting the steps.
The air filter should be replaced when cleaning is ineffective.
(If the filter is dirty and clogged, the correction may not be
completed properly.)
2. Connect the RS-232C termanal of projector
and PC with a RS-232C cable. RS-232C cable (Streight)
1. 5. 3. Setting method
1.Push the power button of the projector and let a lamp turn on. (The signal input is unnecessary.)
* Push the INPUT SELECT button, and please stop "Auto-signal search".
2. Start up service software ［Service ORCA10.exe］ with a computer.
* Please close another software before using the "Service software".
3. Select language and click the [ OK ] button.
4. 1) Select the Serial Port of the computer.
2) Select a model number.
① ②
(Case of AH1000, select the AR100.)
3) Click the [ Adjustment ] button.

5. Click the [ FLTR Sensor ] button.

6. Select the sea level height of the work place and click the [ Do Now ] button.

Progress window

* When error message is displayed,

1)Turn off the main power supply,
and please turn on the main power
supply again.
2)Please carry it out from 1 procedure
once again.
7. In approx. 15 minutes, the "Sensor correction" window closes automatically and completes the correction.
* Turn off the main power supply, and please turn on the main power supply again.

ADJ - 6
2. Microprocessor update procedure
* The update is done by SERIAL terminal connection.
* During update, prevent PC from going into stand-by or shut down.

2. 1. Update by the SERIAL terminal connection

2. 1. 1. Equipment to be used
1. Computer : Use it for the transfer of update data.
2. Communication cable : D-sub 9pin (male/female RS-232C straight)
3. Service Software : [PgSendORCA10.exe] Service software is downloaded from the projector service homepage.
4. Microprocessor Software: Please download the file from the projector service homepage to the PC.

2. 1. 2. Preparation
Computer Projector
1. Connect the RS-232C termanal of projector
and PC with a RS-232C cable.

RS-232C cable (Streight)

2. 1. 3. Update procedure
1. Switch the projector to "Standby" mode (POWER indicator is Lighting in red).
2. Start up service software [ PgSendORCA10.exe ] with a computer.
3. Select language and click the [ OK ] button.

4. 1) Select the Serial Port of the computer.

2) Select a model number.
(Case of AH1000, select the AR100.)
3) Select a microcomputer to update.
4) Click the [ PROGRAM LOAD ] button.
① ②

5. Appoint the microcomputer software that took in a computer beforehand, and click the [ Open ] button.

ADJ - 7
6. Click the [ SOFT UPDATE ] button.

7. Click the [OK] button and start update.

8. Click the [ OK ] button after completion message is displayed.

* Reboot Projector, and please confirm whether the version of the Microprocessor Software is updated definitely,
with sub menu " SELF CHECK " of the main menu " EXT OPTION " .

ADJ - 8
SECTION 4

< Schematic Diagram >

Important Safety Notice
Components identified by the intemational symbol have special characteristics important for safety.
When replacing any of these components, use only the manufacturer's specified ones.

Model No. PT-AR100U / AR100EA / AR100EH ■Notes

1. Resistor
PT-AH1000E All the resistors are carbon 1/4W resistors, unless marked as follows.
The unit of resistance is an OHM [Ω] (K=1 000 M=1 000000).
: Nonflammable : Metal Oxide
: Solid : Metal Film
: Wire Wound : Fuse
2. Capacitor
CONTENTS : Temperature Compensation : Electrolytic
: Polyester : Bipolar
: Metalized Polyester : Dipped Tantalum
1. BLOCK DIAGRAM　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIA-2 : Polypropylene : Z-Type
1.1. Signal Processing 3. Coil
The unit of inductance is a H, unless otherwise noted.
2. INTERCONNECTION BLOCK DIAGRAM　　・・・・・・・・・・・・・・ DIA-3 4. Test Point
: Test Point
3. SCHEMATIC DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ DIA-4 5. HOT and COLD indications
3.1. A -P.C.Board The power circuit board contains a circuit area using a separate power supply to isolate the ground connection.
3.2. S / V -P.C.Board The circuit is defined by HOT and COLD indications in the schematic diagram. Take the precautions below:
6. This schematic diagram is the latest at the time of printing and the subject to change without notice.
4. CIRCUIT BOARDS DIAGRAM　　・・・・・・・・・・・・・・・・・・・・・・・・ DIA-6
4.1. A -P.C.Board (Component Side) ■Precautions
4.2. A -P.C.Board (Foil Side) 1. NEVER touch the HOT part or the HOT and COLD parts at the same time, or you may get an electric shock.
4.3. S / V -P.C.Board 2. NEVER short-circuit the HOT and COLD circuits, or the fuse may blow and the parts may break.
3. NEVER connect an instrument such oscilloscope to the HOT and COLD circuit simultaneously, or the fuse may blow.
Connect the ground of instruments to the ground of the circuit being measured.
4. MAKE SURE to unplug the power cord from the power outlet before removing the chassis.
5. When ordering parts, please check the part number of the "Replacement Parts List".
 AR100

1. BLOCK DIAGRAM
1. 1. Signal Processing

IC1001 IC1300 IC1500 IC1600

E COMPUTER IN
R,G,B

IC1013
X1301
35.455MHz
A1
HD

VD
R
IC1014

INHIBIT_RGB LCD (R)

LVDS LVDS A2
PIHS

LCD (G)
FPGA LCD PANEL
PIVS
Y,PB/CB,PR/CR PICLK CONTROLLER G
COMPONENT IN
3-ch ADC, 35.455MHz
DYNAMIC γ
HDMI RxD LENS CONTROL COLOR UNEVENNESS

RESIZE A3 LCD (B)

F
HDMI1 24.576MHz SD/HD IP CONVERSION
HDMI-1 IN SCL/SDA VIDEO DECORDER
BITMAP OSD
MPEG-NR B
HDMI2 SCL1/SDA1 3DNR
HDMI-2 IN SCL/SDA DETAIL CLARITY２
WAVEFORM MONITOR2

IC1007 MICRO PROCESSOR

Y/C
S-VIDEO IN X1300
VIDEO LPF 27MHz VCXO
A9 V1 IR RECEIVER
VIDEO IN
REM_IM RM2101

D SCL0/SDA0
IC1301 STB_LED

128M POW_LED
IC1008 IC1203 EEPROM LAMP_LED
R1 IN RxD RxD_MAIN

R
TEMP_LED INDICATOR
RS-232C
SERIAL T1 OUT DRIVER TxD
SELECTOR TxD_MAIN IC1305
IC1902 Q1900-Q1902 ! V-P.C.B
64M
RxD_SUB TxD_SUB BUFFER
FLASH IRIS CONTROL
IC1200 ROM MICRO PROCESSOR
A8 S1
GEN_RxD P_KEY_DET
SUB POWER SW
GEN_TxD IC1310, IC1311
IC1002/Q1001 MICRO PROCESSOR KEY1
TRIGGER_1 512M KEY2
BUFFER IC1903 IC1901
TRIGGET 1/2 DDR2 SWITCES
TRIGGER_2 KEY3
VIERA Link SDRAM MOTOR
BUFFER X1200
ANGLE
EDID X2 CONTROL
IC1003/Q1000 10MHz
SENSOR ! S-P.C.B
C
DRIVER DRIVER

EXHAUST AIR
IC1204 IC1202 A11 M2 TEMP
19.943MHz CF2402
THERMO1
RESET EEPROM
SCL2/SDA2

KEYSCAN、SENSOR、MAIN/SUB
! M2-P.C.B

INTAKE AIR
A12 M1 TEMP
CF2401
THERMO2

ECO/NORMAL

UART_TXD/RXD

BLST_ON
IC1800

THERMO3
MAIN_STBY
CFILTER1

FAN14V
CFILTER2

FAN CONTROL
! M1-P.C.B

B IC1801 Q1818 Q1800 Q1817,1802

FAN SENSE3
PWM CONT3

PWM CONT1 PWM CONT4 INTERLOCK

MOTOR SW SW SW SW
IC1900
FAN SENSE1 PWM CONT2 PWM CONT5 FAN SENSE4
DRIVER
FAN SENSE2 FAN SENSE5

A14 A15 A16 A17 A18 A19 A10 A5 A4 A13

FILTER DRIVE
MOTOR P-P.C.Board B-P.C.Board
H1 M3
VHOUT+
VHOUT-
M+

HDRV-
M-

HDRV+

! ! ! ! ! CF2403

FILTER AIR
TEMP
POWER EXHAUST INTAKE LAMP IRIS
FAN FAN FAN FAN FAN H2

! M3-P.C.B
A
O+
I-
I+
O-
IRIS M
HE2201

! H-P.C.B

1 2 3 4 5 6 7 8 9

DIA-2
2. INTERCONNECTION BLOCK DIAGRAM

JK1001 JK1002 JK1003 JK1004 JK1005 JK1006

S-VIDEO/VIDEO_IN TRIGGER YPbPr-IN RGB1-IN RS232C I/F HDMI-IN2 HDMI-IN1
C-G 21

19

17

15

13

11
19

17

15

13

11

1
R

1
B5

B4

B3

B2

B1

A5

A4

A3

A2

A1
C 23

2
C

18

16

14

12

10
B10

2
B9

B8

B7

B6

18

16

14

12

10
22 B

B15

B14

B13

B12

B11
Y

CLKG
DDCG

N.C.

CLK+
SCL
DDC DATA
CLKG

D2G
+5V

D1G
DDCG

N.C.

D1-
CLK+

HPDT

D1+

D2+
SCL
DDC DATA

CEC
D2G

D0G

D2-
+5V

D0+
D1G

D0-
CLK-
D1-
HPDT

D1+

D2+
A9

A8

A7

A6

CEC

D0G

D2-
D0+
D0-
CLK-
Y 1
Y-G
3 G
G
G G

GND

GND

GND

GND

GND
SDA
SCL

+5V

Gin

Rin
NC

HD

Bin

NC
VD
2

H2 A10
H1
E

H-P.C.B
SIDE
1 1
M+ M+
GND

TO IRIS MOTOR
1 2 2
M-
M-

VCOM_OUT
2 3 3

RGBSEL1

RGBSEL2
M- GND

XRESET
GND

LCCOM

LCCOM
SDATA
TEST1

LV10N

LV11N
LV10P

LV11P

Vref10

Vref11
Vref12

Vref13
Vref14

Vref15
Vref16

Vref17
Vref18
VDDH

VDDH

VDDY
VSSH

VSSH
CLKN

VSSY
LVSN

CLKP

SCLK
LVSP

LV0N

LV1N

LV2N

LV3N

LV4N

LV5N

LV6N

LV7N

LV8N

LV9N
LV0P

LV1P

LV2P

LV3P

LV4P

LV5P

LV6P

LV7P

LV8P

LV9P
Vref1
Vref2

Vref3
Vref4

Vref5
Vref6

Vref7
Vref8

Vref9
3 4

VDD

VDD

SCS
VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS

VSS
4
A1

NC

NC

NC

NC

NC
HDRV-
HDRV-

4 5 5

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

46

48

50

52

54

56

58

60

62

64

66

68

70

72

74

76

78

80

82

84
SIDE
HDRV+

8
M+ HDRV+

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

41

43

45

47

49

51

53

55

57

59

61

63

65

67

69

71

73

75

77

79

81

83
1

9
5 6 6
VHOUT+ VHOUT+
TERM
GND
6 7

TERM
7 VHOUT-
VHOUT-
A2

!
8 8 SIDE
GND
GND

LCCOM
VDDY 1
2
NC
VSSY 3

A-P.C.B
4

!
VSSH
NC 5
6
VDDH
VCOM_OUT 7
8
V1 A9 Vref18

F
Vref17 9
10
RM2101 VOUT Vref16
1 1 Vref15 11
STB3.3V STB3.3V
IR RECEIVER 12
GND Vref14
2 2 Vref13 13
REMOCON1 REMOCON1
V-P.C.B

14
VCC Vref12
3 3 Vref11 15
DGND DGND
16
Vref10
4 4 RGBSEL2 17
POWER LED R POWER LED R
18
SN001 D2102 RGBSEL1
5 5 SCLK 19
POWER LED G POWER LED G
LAMP 20
DLV SDATA

LCD (R)
6 6 SCS 21
LAMP LED LAMP LED
1 6 22
Vdd SDA VDD
7 7 NC 23
D2101 TEMP LED TEMP LED
24
B

TEMP VSS
2 5 8 8 LV11N 25
SCL3 SCL3
NC NC
R

26
LV11P
G

9 9 VSS 27
SDA3 SDA3
28
IR

3 4
!

GND SCL D2103 LV10N

10 10 LV10P 29
NC NC
POWER 30
G

VSS
11 11 LV9N 31
3.3V 3.3V
32
LV9P
VSS 33
34
LV8N

D
LV8P 35
36

LCD (G)
VSS
LV7N 37
38
LV7P
VSS 39
INTERLOCK SW
40

OPTICAL BLOCK
LV6N
ZA2001
! SW1800
LV6P 41 !
SW2005 SW2008 SW2011
S1 A8 VSS
42
CLKN 43
44
S-P.C.B

POWER LEFT DOWN 1 1 CLKP

STB3.3V STB3.3V
VSS 45
46
2 2 ON/OFF
LV5N
ON/OFF LV5P 47
48
SW2006 SW2009 SW2012 KEY1
3 3 VSS
KEY1
LV4N 49
50
INPUT RIGHT ENTER 4 4 LV4P
KEY2 KEY2
VSS 51
52
KEY3
5 5 LV3N
KEY3 53
LV3P
54
6 6 VSS
SW2007 SW2010 SW2013 DGND DGND
LV2N 55
56
MENU UP BACK LV2P
VSS 57
58
!

LV1N
LV1P 59
60

LCD (B)
VSS

C
LV0N 61
62
LV0P
VSS 63
64
LVSN
LVSP 65
66

K1- K2-
VSS

! !
NC
68
67

VDD

P.C.B
XRESET 69

P.C.B
70
THERMAL
!
TEST1
FUSE 105℃
P3 A5 Vref9 71
JK9101 K3 FUSE K4 P1 72

!
Vref8
F9101 Vref7 73
K1 1 1
LIVE:Brown 1 1 1 3.3V 74
LIVE

! AC CODE NO
HOLDER 2 2
Vref6
Vref5 75
3.3V 76
GND

Vref4
77
NEUTRAL

K2 3 3 Vref3
NUTRAL:Blue 3 3 3 3.3V 78
3

Vref2
SW9101 Vref1 79
4 4
DGND 80
! VDDH
P-P.C.B

81
5 5 NC
DGND 82
VSSH
LCCOM 83
6 6

TERM
DGND 84

7 7
+U5V

B LAMP
8 8
AGND
TERM

11

13

15

17

19

21

23

25

27

29

31

33

35

37

39

41

43

45

47

49

51

53

55

57

59

61

63

65

67

69

71

73

75

77

79

81

83
SIDE

9
9 9
FAN13V

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

40

42

44

46

48

50

52

54

56

58

60

62

64

66

68

70

72

74

76

78

80

82

84
2

8
10 10

VCOM_OUT
LCCOM
B-P.C.B

RGBSEL1

LCCOM
VDDH

VDDH
VDDY

XRESET
VSSH
FANGND

NC

NC
VSSY

CLKN
RGBSEL2

SCLK

VDD

CLKP

VDD
SDATA
SCS

VSS

VSS

VSS
LV9N

VSS

LV8N

VSS
LV7N

VSS

LV6N

VSS

VSS

LV5N

VSS
LV4N

VSS

VSS
LV2N

VSS

LV1N

VSS
LV0N

VSS

VSS

VSSH
NC

LV8P

LV7P

LV6P

LV5P

LV2P

LV1P

LV0P

NC

NC
LVSN

TEST1
LV11N

LV10N

LVSP
LV11P

LV10P

LV3N
A3

LV9P

LV4P

LV3P
Vref18
Vref17

Vref16
Vref15

Vref14
Vref13

Vref12
Vref11

Vref10

Vref9

Vref8
Vref7

Vref6
Vref5

Vref4
Vref3

Vref2
Vref1
CN3 ! CN1 P2 11 11
LCD17V
!

1 1 1 12 12

TEMP2

TEMP1
Lamp(+) DGND

TEMP4
DGND

DGND
DC380V

GND
13 13
NC NC STB3.3V

A12 A11 A13

BLST ON/OFF

3
NC GND
3 3 14 14
UART RXD
UART TXD

MAIN/STB

4 4 15 15
DGND

4 DC AUX ECO/NOLMAL
Lamp(-)
3.3V

CN2 M1 M2 M3

2
BLST ON/OFF
1

FAN SENSE

FAN SENSE

FAN SENSE

FAN SENSE

FAN SENSE
PWM CONT

PWM CONT

PWM CONT

PWM CONT
UART RXD

PWM CONT
UART TXD

FAN GND
FAN GND

FAN GND

FAN GND

FAN GND
FAN 14V

FAN 14V

FAN 14V

FAN 14V
SHIFT+

FAN 14V
INTAKE AIR EXHAUST AIR FILTER AIR
SHIFT-
DGND

GND
3.3V

TEMP TEMP TEMP

CF2401 CF2402 CF2403

A4 A14 A15 A16 A17 A18 A19

1

5
A
! ! !
M1-P.C.B M2-P.C.B M3-P.C.B
CINEMA FILTER
DRIVE
! ! ! ! !
POWER EXHAUST INTAKE LAMP IRIS
FAN FAN FAN FAN FAN

1 2 3 4 5 6 7 8 9

DIA-3
 +5V +5V +5V +5V
+5V
+13V +13V +13V
+3.3V_STB +3.3V_STB +3.3V_STB +3.3V_STB
+3.3V_STB +3.3V_STB

3. SCHEMATIC DIAGRAM JS1006

+3.3V_REG +3.3V_REG
+3.3V

3.3V-REG
+3.3V
+3.3V_REG +3.3V_REG
+3.3V

+3.3V_A1_REG
+3.3V
+3.3V_REG
+3.3V

+3.3V_REG

3. 1. A-P.C.Board
0
IC1008
C1026 C1041 *Q1904
16V JS1007
16V +3.3V B1CHRC000024
0.1u C1039
0.1u 0
C1366 C1378 C1383
C1514 *R15030
IC1502 R

C0ZBZ0001867
16V
16V
0.1u *IC1016 C1363 C1364
0.01u
16V
10u 10u
C1384
IC1503 0.01u C0DBGFG00005
C1062
C0DBGHC00002 non use *C1953 *C1955
*C1954
10u
10V
10u
10V
10V 10V
6.3V
0.47u
10u 0.1u
*R1965
JS1008 Q1030 *C1137 10V 16V 0.22u *C1527
16V

+
IC1012 *C1135 47k

Thermal Pad

50V
AA_HDMI1_HPGDET
IC1005
16V C1361 4.7u

10
4

5
16V 0.1u 0.1u A31 C1374 C1505

3
C1506
0
ADV7471BBCZ-5 16V A30 C1376 C1509

+
10u

Thermal Pad
C1564 4V100u

C1125
50V

0.1u

+
1u VOUT VIN 10V C1388 C1394 0.1u C1375 10u 0.1u C1504 10u C1508 *R1504
C1370 C1562 100u C1694 C1613

16V
C1066 3.3V_NT C1558 50V
33p 22u 22u 16V 16V C1507 1000p

+
10V 4V 6.3V

C1612
100u 6.3V 10u C1561 100u 47k 10V AI_RLV0N AI_GLV0N

EZJZ1V330GA
50V 0.1u 0.1u

EZJZ1V330GA
16V GND C1385 6.3V 6.3V 4V 4V *Q1500 10u C1676 C1691 IC1600 AA1 LVOR0N IC1600 AF15 LVOG0N
*R1966 *Q1905

R1234 100
10u 6.3V 1000p C1500 C1501 16V

X1_1.2V
NC CONTROL 68p 16V

Thermal Pad

Thermal Pad
0.1u B1GBCFLL0039 B1CHRC000024 AI_GLV0P
C1560 6.3V 6.3V AI_RLV0P 16V

+
50V C1557 C1693

1
AA_HDMI1_PDET IC1600 AA2 LVOR0P IC1600 AE15 LVOG0P

AA_TRIGGER_IN_1
AA_TRIGGER_IN_2
2.2k C1389

AA_HDMI_CEC

AA_KEY3
AA_KEY2
AA_KEY1
*R1964

+
D1006

D1010
JS1009 AA_NT_ON 0.1u 10u 10u 1000p C1697
IC1303
C1692
5V
22u 6.3V
IC1602
C1203
C1AB00003048

10V
50V AI_GLV1N

2.2u
6.3V C1565 C1525 0.1u 1000p AI_RLV1N
10u *R1566 IC1600 Y1 LVOR1N IC1600 AF14 LVOG1N
0
IC1302

FPGA_1.2V
C1055 C1067 C1083 10k C1365 R1330 C1424 100u 0.01u 16V 0.1u
*C1956 22p C0DBAYH00009 470p C1563 16V *R1505 (FIN) 50V
Thermal Pad

SIDE
DGND A1 IC1001 IC1001 B1 TVDD DGND K13 IC1001 IC1001 P10 DVDD DGND P3 IC1001 AGND A9 IC1001 IC1001 B12 VAVDD 16V B-E 22k 0 4V C1556 AI_GLV1P

Q1005 Q1007 C1040 C1027 C1048 C1050 C1117 C1118 C1120 C1121 C1122 DGND A6 IC1001
16V 0.1u
IC1001 B6 TVDD DGND K14 IC1001
16V 0.1u
IC1001 P11 DVDD DGND P7 IC1001 AGND A16 IC1001
16V 0.1u
IC1001 B13 VAVDD
0.1u 0.01u
16V
C1357 C1358 C1359 C1369 50V
C0DBAYY00893
50V 0.01u
16V 16V 0 100
100u 16V
4V
AI_RLV1P
IC1600 Y2 LVOR1P IC1600 AE14 LVOG1P A1
AA_TXD
16V 10V
0.1u 10u C1144
16V 10V
0.1u 10u
C1045
0.1u
16V
10V
10u
0.1u
16V
10V
10u
100u
6.3V
DGND AA7 IC1001 C1056 IC1001 C2 TVDD DGND K15 IC1001 IC1001 P12 DVDD DGND P8 IC1001 AGND A23 IC1001 C1084 IC1001 B14 VAVDD
AA_9VREG
*L1906
J0JYC0000024
*L1907
J0JJC0000022
2V 50V
100u 1000p
4V
220u X1_1.2V
22u
6.3V X1_1.8V 0.01u

3.3V
AI_RLV2N AI_GLV2N
IC1600 AF13 LVOG2N TERM

AA_SDA3

AA_SCL3

AA_MUTE
100u
AA_HPLUG_1_OFF
470p 6.3V
DGND AA12 IC1001
16V 0.1u
IC1001 C6 TVDD DGND K16 IC1001 C1068 IC1001 P13 DVDD DGND P9 IC1001 AGND B9 IC1001
16V 0.1u
IC1001 C10 VAVDD IC1001 AA15 NC C1209
C1368
Thermal Pad AA_FPGA_ON C1646 AI_RLV2P
IC1600 W2 LVOR2P
AI_GLV2P
IC1600 AE13 LVOG2P
*Q1501 1000p

+
C1119 5600p

C1022
AA_RXD 50V IC1001 D3 TVDD DGND K17 IC1001 IC1001 P14 DVDD DGND R3 IC1001 AGND B15 IC1001 IC1001 C11 VAVDD IC1001 AA19 NC IC1300 Y4 ANTHREFIN
3.3V

16V
1.2V 50V

0.1u
50V 22u R1318 B1GBCFLM0003 AI_GLV3N
470p 16V 0.1u C1696 AI_RLV3N
DGND AB1 IC1001 C1057 IC1001 D6 TVDD DGND L3 IC1001 DGND R7 IC1001 AGND B16 IC1001 C1085 IC1001 C12 VAVDD IC1001 AA20 NC C1367 6.3V 510k IC1600 W3 LVOR3N IC1600 AD13 LVOG3N
R1121 0 50V IC1300 AH6 RTCXTALIO 10u 10V
C1211 22u C1526 C1645 C1624 1u

+
1%
DGND AB7 IC1001 DGND L9 IC1001 IC1001 P16 DVDD DGND R8 IC1001 AGND C9 IC1001 IC1001 C14 VAVDD IC1001 AA21 NC C1524 C1523 AI_GLV3P
IC1201
AI_RLV3P
C1210
3.3V 6.3V 6.3V 25V

3.3V_PHY
AA_HDMI1_HOTPLUG 16V 0.1u C1069 16V 0.1u C1360 C1387 6.3V 100u IC1600 W4 LVOR3P IC1600 AC13 LVOG3P
16V 16V C1698 C1648

3.3V_WL
DGND AB12 IC1001 IC1001 H1 TVDD DGND L10 IC1001 IC1001 P17 DVDD DGND R9 IC1001 AGND C16 IC1001 IC1001 D10 VAVDD IC1001 C7 NC 10V IC1300 AK6 RTCXTALIN 16V C1430 10u C1695 4V

16V 0.1u

AA_RESET
0.1u

AJ_VREFCOM

AI_RLVCLKN
AI_RLVCLKP
HDMI1_5V_DET 0.1u 0.1u 0.1u AI_RLV4N AI_GLV4N 0.1u 25V
1u 330p
IC1009
C1716

AJ_VREF18
AJ_VREF17
AJ_VREF16
AJ_VREF15
AJ_VREF14
AJ_VREF13
AJ_VREF12
AJ_VREF11
AJ_VREF10

AA_SDATA2

AI_RLV10N
AI_RLV10P
0.1u 33u 1000p

AI_RLV11N
AI_RLV11P

AI_RLV9N
DGND AB17 IC1001 IC1001 H2 TVDD DGND L11 IC1001 IC1001 R10 DVDD DGND T3 IC1001 AGND C17 IC1001 IC1001 D14 VAVDD IC1001 C8 NC C1667 IC1600 V1 LVOR4N IC1600 AF12 LVOG4N

AI_RDXOUT
16V C1644

C1309
C1058 16V 0.1u C1086 16V

AJ_VCOMR

AI_RLV9P

AI_RLV8N

AI_RLV8P

AI_RLV7N
AI_RLV7P

AI_RLV6N

AI_RLV6P

AI_RLV5N

AI_RLV5P

AI_RLV4N
AI_RLV4P

AI_RLV3N
AI_RLV3P

AI_RLV2N
AI_RLV2P

AI_RLV1N
AI_RLV1P

AI_RLV0N
AI_RLV0P
+
RB751V-40TE-17
50V

AJ_LCOMR

AI_RENY2
AI_RENY1
C1310
25V

AA_SCLK2

AI_MSELR
IC1300 J1 VRLAD[0] 50V

AA_SCS2
C1312 0.1u
0.1u

AA_SOG1_IN

AA_B1_IN

AA_G1_IN

AA_R1_IN

ADC1_HD_IN

ADC1_VD_IN
10u

16V 0.1u

AI_FRPR
*D1200

AI_RDY
R1130 DGND AC1 IC1001 DGND L12 IC1001 IC1001 R11 DVDD DGND T7 IC1001 AGND C18 IC1001 IC1001 G9 VAVDD IC1001 D7 NC AI_RLV4P AI_GLV4P

16V
B0JCAE000001
D1051 16V 10V 1u
47k IC1600 V2 LVOR4P IC1600 AE12 LVOG4P

10V

C1502
16V 0.1u 16V 0.1u

10V 10u
DZ2J056M0L
RS232C I/F

C1503
C1103 DGND AC7 IC1001 DGND L13 IC1001 C1070 IC1001 R12 DVDD IC1001 G10 VAVDD IC1001 D8 NC IC1300 M1 VRLAD[1] AM_FPGAVS
IC1600 D25 VSYNC AM_DCLK AI_RLV5N AI_GLV5N 25V

10V
FL1000

AJ_VREF9
AJ_VREF8
AJ_VREF7
AJ_VREF6
AJ_VREF5
AJ_VREF4
AJ_VREF3
AJ_VREF2
AJ_VREF1
2.2u DGND AC12 IC1001 IC1001 N2 TVDD DGND L14 IC1001 IC1001 R13 DVDD DGND T9 IC1001 AGND C20 IC1001 IC1001 G11 VAVDD IC1001 K4 NC AA_ANSYIN FA_B0 IC1600 H26 DCLK C1622 IC1600 U1 LVOR5N IC1600 AF11 LVOG5N C1649 33u

AUDIOOUT-R

AUDIOOUT-L
C1059 C1087 C1670 C1681

C1437
J0HAYY000046 IC1300 R1 VRLAD[2] IC1300 M2 ANSYIN IC1300 F22 PI1D[0] AM_FPGAHS

10V
C1623
16V 0.1u

10u
Thermal Pad
C1518

0.1u
10V DGND AC17 IC1001 IC1001 N3 TVDD DGND L15 IC1001 IC1001 R14 DVDD AGND D9 IC1001 IC1001 G12 VAVDD IC1001 N4 NC AA_TXD_STB C1519 C1520 IC1600 D26 HSYNC IC1600 AA23 VDD10 IC1600 AB2 VDDA33 AI_RLV5P AI_GLV5P
C1790
HDMI1_SDA C1313 AA_ANSCIN FA_B1 220u 10u 0.1u 1u IC1600 AE11 LVOG5P

B0ZBZ0000156

B0ZBZ0000156
16V 0.1u 16V 0.1u 22p
*IC1015

10u
C1434 0.1u16V 0.1u16V

E
DGND AC23 IC1001 IC1001 U3 TVDD IC1001 R15 DVDD DGND T11 IC1001 AGND D16 IC1001 IC1001 G13 VAVDD AA_RXD_STB 16V IC1300 R2 ANSCIN IC1300 C21 PI1D[1] 10V 16V
10V IC1300 D24 TESTH2[0] 4V 50V IC1600 AB3 VDD10 IC1600 AB24 VDDA33 10V AI_RLV6N AI_GLV6N

C1620
AA_DDCSDA1 AA_RESET

G
10

D1043
0.01u
DGND C1 IC1001 IC1001 V2 TVDD
R
DGND L17 IC1001 IC1001 R16 DVDD DGND T12 IC1001 AGND D17 IC1001 IC1001 Y3 NC AA_HDMI1_PDET IC1600 R1 LVOR6N IC1600 AF9 LVOG6N
L

D1039
AA_ANMPIN FA_B2
C1060 C1071 C1AB00002428 10u C1671 C1604

16V
HDMI1_SCL IC1300 J2 ANMPIN IC1300 D21 PI1D[2]

HDMI-IN2
5

4
IN4 OUT4
non use

AJ_VREFCOM
DGND C3 IC1001 IC1001 V3 TVDD DGND M4 IC1001 IC1001 R17 DVDD DGND T13 IC1001 AGND D18 IC1001 IC1001 Y4 NC IC1300 F25 TESTH2[1] IC1600 AB4 VDD10 IC1600 AC3 VDDA33 AI_GLV6P

AI_RENY2

AI_RENY1

AA_SCS2

AI_RDXOUT
AI_RLV6P

AJ_VREFCOM

AJ_VREF18
AJ_VREF17

AJ_VREF16

AJ_VREF15
AJ_VREF14
AJ_VREF13
AJ_VREF12

AJ_VREF11
AJ_VREF10
AJ_VREF9

AJ_VREF8
AJ_VREF7
AJ_VREF6
AJ_VREF5
AJ_VREF4

AJ_VREF3

AJ_VREF2
AJ_VREF1

AI_FRPR
AI_MSELR

AI_RDY
AA_DDCSCL1 FA_B3 AM_A1R0 AM_A2R0 16V IC1600 R2 LVOR6P IC1600 AE9 LVOG6P

AJ_VREF3

AJ_VREF5

AJ_VREF7

AJ_VREF9

AJ_VREF10

AJ_VREF12

AJ_VREF14

AJ_VREF16
C1030 C1042 16V 0.1u 16V 0.1u *C1130 GUARD_CLK JS1012 JS1014 0.1u16V 0.1u16V

AJ_VREF1

AJ_VREF2
DGND C4 IC1001 DGND M9 IC1001 AGND D19 IC1001 IC1001 Y5 NC 14 0V AA_HPLUG_1_OFF JS1016 IC1600 B10 R1IN0 IC1600 B22 R2IN0

AJ_VREF18
1 JS1018

AJ_VREF4

AJ_VREF6

AJ_VREF8

AJ_VREF11

AJ_VREF13

AJ_VREF15

AJ_VREF17
IN3 OUT3 C1628
AA_HDMI_CEC 0.1u 10V
C1049 C1051 C1046 V+ GND
K1KB80A00141 *L1908
+5V_REG IC1300 V3 VCXOCLKIN IC1300 B3 TESTB[0] POCLK B23 IC1300
GRAPHICS AND VIDEO INPUT BUS IC1600 AB23 VDD10 IC1600 AC18 VDDA33 AI_RLV7N AI_GLV7N

C1371
DGND C5 IC1001 DGND M10 IC1001 DGND T15 IC1001 AGND D20 IC1001 IC1001 Y15 NC AA_HPLUG_2_OFF AM_A1R1 AM_A2R1 IC1600 AD9 LVOG7N

50V 22p
16V 10u 100u C1088 10V10u 2 13 FA_B4 C1600 C1682
HDMI1_CKN C1044 0.1u 10V OUTb OUTa J0JYC0000021 AA_VCXO_PWM IC1300 J4 ANRIN IC1300 F21 PI1D[4] 0 0 IC1600 A10 R1IN1 IC1600 AA4 VDDB33

2
IN2 OUT2 6.3V DGND D4 IC1001 DGND M11 IC1001 DGND T16 IC1001 AGND G14 IC1001 IC1001 C21 AAVDD IC1001 Y18 NC AA_TRIGGER_2 IC1300 H1 VRHAD[0] IC1300 C23 TESTB[1] IPCLK B16 IC1300 IC1600 AC5 VDD10

56p
IC1600 AC20 VDDA33 AI_GLV7P

50V

C1372
470p 10u 3 12 *C1133 C1440 0.1u AI_RLV7P
16V N.C. N.C. FA_B5 AM_A1R2 AM_A2R2 IC1600 R4 LVOR7P IC1600 AC9 LVOG7P
16V 0.1u *C1129 10V 1u0V 10u 0.1u16V 0.1u16V
50V DGND D5 IC1001 DGND M12 IC1001 DGND T17 IC1001 AGND G15 IC1001 IC1001 D21 AAVDD *C1127
*R1217 4 11 AA_TRIGGER_1 IC1300 M4 ANGIN IC1600 B11 R1IN2 IC1600 B23 R2IN2 IC1600 AA25 VDDB33

1
IN1 OUT1 C1435

1u

1u
D1015 HDMI1_CKP CAPb CAPa 80 IC1300 F24 TESTB[2] MCLKSEL[0] F23 IC1300 IC1600 AC16 VDD10 IC1600 AD2 VDDA33 C1611 AI_GLV8N

1u

1u
1u
1u

1u
1u

1u
1u
1u
1u
1u

1u
1u
1u
1u

1u

1u
1u
1u
1u

1u
1u

1u

1u
1u
1u
1u
10V 1u 22 *R1221 *C1131 10V C1436 10V AI_RLV8N

0.1u 16V
IC1011 DGND M13 IC1001 DGND U7 IC1001 AGND H7 IC1001 IC1001 E21 AAVDD IC1001 Y20 NC 10V 2.2u 5 10 AA_STB_LED 40 FA_B6 AM_A1R3 AM_A2R3 IC1600 P1 LVOR8N IC1600 AF8 LVOG8N

10V

C1373
D4ED1270A008 C1061 C1072 C1089 10V JS1013 JS1015 C1672 C1641 16V
HDMI1_0N INb INa 79 10u IC1300 G2 VRADLS IC1300 R4 ANBIN IC1300 F20 PI1D[6] JS1017 IC1600 A11 R1IN3 IC1600 A23 R2IN3 IC1600 AC8 VDDB33

9G
G
220p

C1438
K1FY119E0025

16V

16V
16V
16V

16V

16V
16V
16V

16V
16V
16V
16V
16V

16V
16V
16V
16V

16V
16V
16V

16V
16V

16V
16V

16V

16V
16V
16V
16V
DGND E4 IC1001 DGND M14 IC1001 IC1001 AA16 DVDDIO DGND U8 IC1001 AGND H8 IC1001 IC1001 F20 AAVDD IC1001 Y21 NC 6 9 10V 1u AA_POW_LED 39 10u IC1300 P1 VRHAD[2] IC1300 E6 IFMD[0] MCLKSEL[1] C22 IC1300 IC1600 AC17 VDD10 0.1u AI_RLV8P AI_GLV8P
22 50V
ADR Vref 78

ANAROG & DIGITAL INPUT PORT

16V 0.1u 16V 0.1u 16V 0.1u C1399 FA_B7 C1920 C1923 AM_A1R4 AM_A2R4 IC1600 P2 LVOR8P IC1600 AE8 LVOG8P
DGND F3 IC1001 IC1001 J8 CVDD DGND M15 IC1001 IC1001 U9 DVDDIO DGND U17 IC1001 AGND H9 IC1001 IC1001 F21 AAVDD IC1001 Y22 NC C1213 38 IC1300 E1 VRHADLS IC1300 M3 ANYIN IC1300 C19 PI1D[7] C1915 C1911 C1919 D1904 IC1600 B12 R1IN4 IC1600 B24 R2IN4 0.1u16V IC1600 AC14 VDDB33

C1217
C1683

NT
D1016 7 8 C1200 10V C1916 0

50V

10u
*C1134 16V 16V

27p
50V

C1759
C1760
C1761

C1762
C1763

C1699

C1718
C1719
C1720

C1764
C1765
C1766
C1767

C1768
HDMI1_0P SDA SCL 77 AA_WLGIO4 IC1300 C5 IFMD[1] MCLKSEL[2] D22 IC1300 16V 220p IC1600 AC21 VDD10 220p AI_GLV9N

C1700

C1701
C1702
C1703
C1704

C1705

C1707
C1708
C1709

C1710

C1713
C1714
C1715
C1717
16V AI_RLV9N

JK1005
C1090

C1706
1u 16V B0JCPE000048 16V
D4ED1270A008 DGND M16 IC1001 IC1001 U10 DVDDIO DGND U22 IC1001 AGND H10 IC1001 IC1001 G16 AAVDD IC1001 Y23 NC *R1215 10V 10u AA_NT_ON 37 FA_B8 1u 1u 50V 1u 0.22u AM_A1R5 AM_A2R5 C1601 50V C1605 IC1600 N1 LVOR9N IC1600 AF7 LVOG9N
HDMI1_1N 9p 76 AA_WLPWRBTN IC1300 G1 VRLADLS IC1300 R3 ANUIN IC1300 D19 PI1D[8] 1u IC1600 A24 R2IN5 IC1600 AC15 VDDB33

+
C1113 22 0.1u
DGND J10 IC1001 DGND M17 IC1001 IC1001 U11 DVDDIO DGND V1 IC1001 IC1001 G20 AAVDD IC1001 G17 NC 36 IC1600 AC22 VDD10 IC1600 AE16 VDDA33 AI_GLV9P
2.2u
10V DGND J11 IC1001
C1063
IC1001 K8 CVDD DGND N1 IC1001
C1073
IC1001 U12 DVDDIO DGND W20 IC1001 AGND H12 IC1001
16V 0.1u
IC1001 G21 AAVDD IC1001 H15 NC
DGND *R1222
WP_PHY25MHZ 35
75 16V
IC1300 C1 VRH IC1300 J3 ANVIN
FA_B9
IC1300 E19 PI1D[9] to FPGA AM_A1R6
IC1600 B13 R1IN6
AM_A2R6
IC1600 C25 R2IN6 0.1u16V 0.1u16V
0.1u
C1614 IC1600 AD11 VDDB33
AI_RLV9P
IC1600 N2 LVOR9P IC1600 AE7 LVOG9P

1u

1u

1u

1u

1u
+
2.5V
D1017
3.3V RESIZE -> FPGA FPGA -> IC1600
C1091
1.2V
22 25V 25V 25V 25V 25V
HDMI1_1P 16V 0.1u 16V 0.1u *R1219 *R1220 *C1132 74 WP_MDIO IC1300 E24 SYSCLKSELX
RGB OUTPUT PORT IC1600 AD5 VDD10 IC1600 AE20 VDDA33 AI_RLV10N AI_GLV10N

C1661

C1662

C1663

C1664

C1660
D4ED1270A008 DGND J12 IC1001 IC1001 K9 CVDD DGND N7 IC1001 IC1001 U13 DVDDIO DGND W21 IC1001 AGND H13 IC1001 IC1001 H21 AAVDD IC1001 H16 NC TP1015 10p 34 AM_A1R7 AM_A2R7 16V IC1600 M1 LVOR10N IC1600 AF6 LVOG10N
100 100 10V 10u C1673 C1684
HDMI1_2N 16V 0.1u
*IC1200 73 WP_MDC IC1300 V5 DAC_AVD1 IC1300 C2 VRL IC1300 W5 VDHSIN AM_POCLK IC1600 A13 R1IN7 IC1600 C26 R2IN7 IC1600 AE5 VDDB33 0.1u 0.1u 0.1u 0.1u 0.1u

*R1218
IC1001 L7 CVDD DGND N8 IC1001 IC1001 U14 DVDDIO DGND W22 IC1001 AGND H14 IC1001 IC1001 H17 NC AA_DDCSDA1 WP_RXD0 33 IC1300 A19 SYSCLK POCLKO AH30 IC1300 IC1600 D5 VDD10 IC1600 D7 VDDA33 AI_GLV10P

C1218
0.1u AI_RLV10P

50V
27p
72 WP_PD AM_A1R8 AM_A2R8 IC1600 M2 LVOR10P IC1600 AE6 LVOG10P

47k

R1372
*R1214 *R1216 C1214 0.1u16V 0.1u16V
C1052 C1047 DGND J14 IC1001 IC1001 L8 CVDD IC1001 U15 DVDDIO DGND W23 IC1001 AGND H20 IC1001 IC1001 J22 AAVDD *C1128 AA_DDCSCL1 C1207 WP_RXD1 32 IC1300 L5 AVD1_0 IC1300 V6 DAC_AVD1 IC1300 W4 VDVSIN
VDD_CORE IC1600 C10 R1IN8 IC1600 C22 R2IN8 C1618 IC1600 L2 VDDB33

0
C1064 C1074 C1092 1u C1913 C1668 C1669 C1686 C1687 C1688
RGB1-IN

HDMI1_2P C1114 C1112 100 100 50V 71 WP_TXC C1396 39p IC1600 D21 VDD10 IC1600 D9 VDDA33 AI_GLV11N
IC1013 100u *D1054 C1391 AI_RLV11N
10V 10V 16V

16V

16V

16V

16V

16V
16V
HD 33u 2.2u DGND J15 IC1001 IC1001 M7 CVDD DGND N10 IC1001 IC1001 U16 DVDDIO DGND Y7 IC1001 AGND J20 IC1001 IC1001 J23 AAVDD WP_RXD2 31 FA_G0 C1390 50V AM_A1R9 AM_A2R9 C1674 C1685 IC1600 M3 LVOR11N IC1600 AD6 LVOG11N C1616

50V
FAN <-> SUBMAIKON
50V

*R1213
70 WP_RXC IC1300 H6 AVD0_0 IC1300 L6 AVD1_0 IC1300 V9 DAC_AVD1 IC1300 K1 VIM[0] IC1300 W3 VDSOGIN IC1300 F19 PI1D[10] 0.47u IC1600 C23 R2IN9

C1308
6.3V DZ2J056M0L IC1600 C11 R1IN9 IC1600 L23 VDDB33

47k
10u 16V 0.1u 16V 0.1u 16V 0.1u 10V 10u C1204 C1380 C1335 0.1u
+STB3.3V

10p

C1615
10V 10V DGND J16 IC1001 IC1001 M8 CVDD DGND N11 IC1001 IC1001 Y16 DVDDIO DGND Y12 IC1001 AGND K20 IC1001 AA_DDCSDA2 WP_RXD3 30 C1450 10p 0.1u AI_RLV11P AI_GLV11P
1u 16V C1639 0.1u
RGB1-SDA 69 WP_CRS FA_G1 C1301 IC1300 J15 VDDI AM_A1R10 AM_A2R10 IC1600 M4 LVOR11P IC1600 AC6 LVOG11P
TP1012 DGND J17 IC1001 DGND N12 IC1001 DGND Y17 IC1001 AGND K21 IC1001 AA_DDCSCL2 29 IC1300 M9 AVD0_0 IC1300 P5 AVD2_0 IC1300 N1 VIM[1] 10u IC1300 W2 VDSOYIN AM_PWM IC1600 C12 R1IN10 IC1600 D24 R2IN10 0.1u16V 0.1u16V IC1600 M23 VDDB33 C1640
*D1053 10V 0.1u 0.1u 8p C1627
C1316

0.1u 16V
68 WP_COL POFLD AG28 IC1300 IC1600 E4 VDD10 IC1600 D13 VDDA33

10V
16V 16V 10V 50V 16V 16V
DGND K3 IC1001 DGND N13 IC1001 DZ2J056M0L AA_GEN_RXD AA_MUTE WP_TXD0 28 FA_G2 0.1u IC1300 J16 VDDI AM_ACT R1524 1k AM_A1R11 AM_A2R11 C1677 C1606 25V

C1439

C1300
0.1u
HD
67

NT-->SCX1
IC1300 K3 AVD0_1 IC1300 N3 AVD1_1 C1398 IC1300 T1 VIM[2] IC1300 AF21 LVDSEATIN IC1300 D18 PI1D[12] IC1300 A17 XTALIN 16V
VDD_IO C1392
IC1902
*C1864 IC1600 C13 R1IN11 IC1600 E24 R2IN11 IC1600 P4 VDDB33 AI_RLVCLKN
A2

10V
DGND K10 IC1001 AGND L20 IC1001 AA_GEN_TXD AA_9VREG WP_TXD1 27 POACTB AF30 IC1300 AM_LCDVS IC1600 E23 VDD10 IC1600 D15 VDDA33 IC1600 T1 LVOCLRN AI_GLVCLKN

2.2u
C1093 0.1u 25V 0.1u

IC1001 66 WP_RXER IC1300 J22 VDDI 0.1u 10u

*C1136 FA_G3
35.455MHz +13V

B0ZBZ0000156

10u
*L1834 0.1u16V 0.1u16V

D1030
B0ZBZ0000156
D1033
B0ZBZ0000156
D1035
B0ZBZ0000156
D1037
B0ZBZ0000156
D1041
B0ZBZ0000156
D1045
B0ZBZ0000156
D1047
B0ZBZ0000156
D1049
DGND K11 IC1001 DGND N15 IC1001 AGND L21 IC1001 IC1001 G7 PVDD AA_COOL_H WP_TXD2 26 IC1300 N4 AVD1_1 IC1300 T9 AVD2_0 IC1300 E22 TESTH IC1300 E18 PI1D[13] IC1300 C17 XTALIO AM_LCDHS 16V 16V C1629 IC1600 R24 VDDB33
C1BB00000888

10V 10u
C1333 C1395 0.1u AI_RLVCLKP

*C1138
DDC_5V 16V *C1139 65 WP_TXEN C1317 POVSB AG30 IC1300 IC1300 W26 MVREF[0] AM_POCLK AM_DCLK IC1600 K4 VDD10 IC1600 D17 VDDA33 C1619 IC1600 T2 LVOCLRP AI_GLVCLKP
D4ED11200005 DGND K12 IC1001 DGND N16 IC1001 AGND L22 IC1001
16V 0.1u
IC1001 G8 PVDD B1ADCE000013 B1ADCE000013
*R1225
0.1u 0.1u AA_COOL_L WP_TXD3 25
from NT 16V
C1341 FA_G4 CRYSTAL C1303 0.1u IC1300 K15 VDDI IC1300 J11 VDDE IC1300 E26 SSTL18_VDDE IC1500 A6 - IC1500 B5 - IC1500 A8 - IC1500 P9 - AM_A1G0 AM_A2G0 C1602 C1607 IC1600 AE10 LVOCLGP

16V 16V

16V 16V
D1011 C1094 *Q1010 1.5k 64 WP_RXDV IC1300 N9 AVD0_1 IC1300 R9 AVD1_1 IC1300 U9 AVD2_1 IC1300 E2 ADC_AVD IC1300 F18 PI1D[14] C1546 C1534 IC1600 B6 G1IN0 IC1600 B18 G2IN0 IC1600 U3 VDDB33
C1AB00003048
16V

16V
*Q1011 *Q1012 16V 0.1u 0.1u C1400 0.1u 10p C1326 C1354 C1393 C1531 16V
DGND N17 IC1001 AGND L23 IC1001 *Q1009 AA_FANEN3 24 IC1300 H4 BC[0] PLL_VD1 A22 IC1300 POHSB AG29 IC1300 0.1u 0.1u C1553 C1552 J0JJC0000022 *C1858 IC1600 D19 VDDA33 FL1600
B1ABCF000098 63 WP_PHYRST 16V 16V C1302 50V 0.1u IC1300 J12 VDDE 0.1u IC1300 E29 SSTL18_VDDE 0.1u IC1500 D13 - 0.1u IC1500 A11 - IC1500 B12 - AM_A1G1 AM_A2G1 16V
C1116 16V 0.1u 16V FA_G5 C1567 4.7u 0.1u FL1604
PLL
C1339 56p 47p 0.1u16V 0.1u16V J0HAAB000046
VD
F
B1ABCF000098 AA_FANEN2 23 IC1300 T3 AVD2_1 IC1300 L9 ADC_AVD IC1300 D17 PI1D[15] 16V 16V 16V C1545 C1533 *C1863 IC1600 A6 G1IN1 IC1600 A18 G2IN1 IC1600 V23 VDDB33
C1397 0.1u 50V
VD 0.1u 62 0.1u IC1300 L4 BC[1] PLL_VD2 A21 IC1300 0.1u 0.1u
10p 50V 50V *C1865 10u IC1600 L12 VDD10 IC1600 D22 VDDA33 J0HAAB000046
IC1014

G
16V 10p 50V *R1876 C1675
AA_HDMI2_PDET AA_FANEN 22 16V C1340 FA_G6 IC1300 L25 VDDI IC1300 J19 VDDE IC1300 E30 SSTL18_VDDE IC1500 E5 - IC1500 F1 - IC1500 F7 - 10u AM_A1G2 AM_A2G2 AI_RENY2

G
16V C1550 16V C1678 C1608
61 IC1300 T4 AVD2_1 IC1300 E4 DAC_AVD IC1600 B7 G1IN2 IC1600 B19 G2IN2 IC1600 IC1600 J1 ENBY2R AI_GENY1

16V
C1401 C1625
IC1605
0.1u

16V

16V
C1318 C1355 16V

*R1858
TRIGGER
IC1603
TP1013 C1530 4

*R1223
AA_LAMP_LED AA_WLRST 21 0.1u IC1300 P4 BC[2] PLL_VD3 A20 IC1300 LVDSO1[0] AK22 IC1300 TP1307 C1544 C1532 1000p 47k IC1600 L15 VDD10 IC1600 E25 VDDA33 IC1600 AE18 ENBY1G
LCDVS

*R1859
C1334 C1914 *Q1814

*R1224
2.7k

220
D4ED11200005 16V 0.1u16V 4

K2HC204B0002
RGB1-SCL *Q1013 60 FA_G7 0.1u IC1300 L26 VDDI IC1300 J20 VDDE 0.1u IC1300 F26 SSTL18_VDDE 0.1u IC1500 E12 - 0.1u IC1500 F16 - 0.1u IC1500 F10 - 50V *Q1816 AM_A1G3 AM_A2G3 AI_RENY1 25V1u

2.7k

220
16V

C1918 16V 1u

C1917 16V1u
D1012 AA_TEMP_LED 20 IC1300 F17 PI1D[17] 0.1u B1CHQD000008 IC1600 A7 G1IN3 IC1600 A19 G2IN3 0.1u16V 0.1u16V AI_GENY2
0.1u 16V 16V
3.3V

10V
B1CHQD000008

1u
B1GBCFLM0003 59 IC1300 H3 BR[0] PLL_VD3_1 B20 IC1300 LVDSO1[1] AH22 IC1300 16V IC1600 M11 VDD10 IC1600 G4 VDDA33 3 IC1600 AF18 ENBY2G C1650

C1922 16V
JK1002
*R1002 0 19 16V IC1300 N25 VDDI IC1300 K11 VDDE C1348 IC1300 H25 SSTL18_VDDE IC1300 M27 MOCDRES IC1300 J26 MVREF[1] IC1500 M5 - IC1500 L1 - IC1500 E15 - AM_A1G4 AM_A2G4 AI_RDY 3 C1712
LCDHS

C1202
FA_G8
24.576MHz

AI_GLVCLKN
AI_GLVCLKP
C1679 C1609

16V 16V

16V 16V
1W 1W

*R1863

+
C1208 C1319 C1327

0.22u

AJ_VREFCOM
0.1u 25V

22k
58 IC1300 C16 PI1D[18] C1547 C1535 IC1600 B8 G1IN4 IC1600 B20 G2IN4 IC1600 H2 DYOUTR AI_GDY

AI_GLV11N
AI_GLV11P

AI_GLV10N
AI_GLV10P

AI_GDXOUT
AJ_LCOMG
16V
22

AA_SDATA2
C1426 + R1529

AJ_VREF18
AJ_VREF17
AJ_VREF16
AJ_VREF15
AJ_VREF14

AJ_VREF13
AJ_VREF12
AJ_VREF11
AJ_VREF10
C1901

AA_SCS3
0.1u 0.1u C1529 2

AI_GENY2
AI_GENY1
AA_SCLK2

AI_GLV9N
AI_GLV9P

AI_GLV8N
AI_GLV8P

AI_GLV7N
AI_GLV7P

AI_GLV6N
AI_GLV6P

AI_GLV5N
AI_GLV5P

AI_GLV4N
AI_GLV4P

AI_GLV3N

AI_GLV3P

AI_GLV2N
AI_GLV2P

AI_GLV1N
AI_GLV1P

AI_GLV0N
AI_GLV0P

AI_MSELG
AA_WLEN 18 IC1300 L3 BR[1] PLL_VD4 A24 IC1300 LVDSO1[2] AK21 IC1300 AM_R_OD2 IC1600 M16 VDD10 IC1600 H3 VDDA33 IC1600 AF19 DYOUTG
SCX1 FRONT 16V C1336 0.1u 0.1u AM_FPGAHS *R1875 1u

AJ_VCOMG
*R1003 1u
Q1031 0 0.1u C1900 25V

AI_FRPG
57 FA_G9 16V IC1300 N26 VDDI 16V IC1300 K12 VDDE TP1306 C1906 IC1500 M12 - 0.1u IC1500 L16 - IC1500 G11 - IC1500 R2 - IC1500 N5 - IC1500 G16 - *Q1815 AM_A1G5 AM_A2G5 AI_RDXOUT 2
*IC1801

AI_GDY
10V 10u

10V 10u
AA_HDMI2_HPGDET 0.1u
*IC1802 0.1u16V 0.1u16V

C1428

C1425
AnalogInput HDMI IN HDMI Sound OUT 10V 17 IC1300 D16 PI1D[19] 16V 0.1u 6.3V 33u C1548 C1536 22k IC1600 A8 G1IN5 IC1600 G2 DXOUTR AI_GDXOUT
Digital Video OUT HDMI Sound IN PWM OUT 56 AA_ADV1_ARST AA_RESET AA_RXD_MAIN AN_D0 IC1300 P3 BR[2] PLL_VD5 A18 IC1300 LVDSO1[3] AH21 IC1300 16V 16V 47u 0.1u 0.1u AM_R_OD3
R1530 22
AM_FPGAVS IC1600 R11 VDD10 1 IC1600 AE19 DXOUTG

*R1862
B1GBCFLM0003 25V

OUT
1

10k
16 IC1300 AB5 GIO[0] IC1300 AF1 GIO[20] IC1300 E7 GIO[40] IC1300 B27 SI0 IC1300 AH7 DB[0] IC1300 AK10 ADL[0] IC1300 P21 VDDI IC1300 K19 VDDE IC1300 J25 SSTL18_VDDE IC1500 N4 - IC1500 T6 - IC1500 K11 - IC1500 R1 - IC1500 M6 - IC1500 G15 - AM_A1G6 AM_A2G6

AJ_VREF9
AJ_VREF8
AJ_VREF7
C1680 C1610 0.1u

C1126
D1905

0.1u

IN
*R1004 0 C1320

OUT
GUARD_CLK 16V

AJ_VREF6
AJ_VREF5

AJ_VREF4
AJ_VREF3
AJ_VREF2
AJ_VREF1
55 IC1600 B9 G1IN6 IC1600 B21 G2IN6 C1651 33u

22k

G
16V

16V
R1531 22
C0DBGYY02198

16V

16V

IN
C1115 AA_SOG1_IN 15 AA_ADV1_VRST AA_SDATA2 AA_HDMI1_HPGDET AA_TXD_MAIN AN_D1 AN_A1 IC1300 V1 DAOUTS CLK245_1 PLL_VD6 Y1 IC1300 0.1u C1349 LVDSO1[4] AK20 IC1300 C1402 C1429 C1413 C1427 C1549 C1528 C1537 AM_R_OD4 R1539 56 IC1600 R16 VDD10 IC1600 J4 VDDA33 25V

*R1854
C1031

G
0.1u 1000p 22 0.47u
R1185 B0JCPE000048
JK1004 AGND 16V 50V
IC1001 A15 SYNC2 IC1001 B5 IC1001 AB2 P0 SCLK/DST_CLK Y9 IC1001 IC1001 P20 BCLK0/SPDIF_IN2
PWM1A R23 IC1001 *R1005 0 14
54 IC1300 AB6 GIO[1] IC1300 D7 GIO[41] IC1300 A29 SO0 IC1300 AG7 DB[1] IC1300 AJ10 ADL[1] IC1300 AE15 SDCSB 16V IC1300 P22 VDDI
C1328
IC1300 K20 VDDE 0.1u
16V
IC1300 K21 SSTL18_VDDE 0.1u 0.1u 0.1u IC1500 N13 - 0.1u 0.1u IC1500 M15 - IC1500 P2 - IC1500 N6 - IC1500 R4 - 10.5V
*C1850 *C1851 C0GBG0000053 AM_A1G7
IC1600 A9 G1IN7
AM_A2G7
IC1600 A21 G2IN7 0.1u16V 0.1u16V
IC1600 FL1601 FL1605
AA_G1_IN C1032 16V
Filter 22
53 AA_FPGA_ON AA_SCLK2 AA_HDMI2_HPGDET AA_GEN_RXD AN_D2 AN_A2 IC1300 V4 DAOUTBIN C1433 0.1u LVDSO1[5] AH20 IC1300
16V
0.9V 0.1u16V 16V 0.1u
16V AM_R_OD5
R1532 22
*R1864 10u 10u IC1600 T12 VDD10 J0HAAB000046 J0HAAB000046

10
10V
1u
IC1001 A14 AIN4 IC1001 A5 IC1001 AC2 P1 LRCLK/DSD2B/DST_FS Y8 IC1001 IC1001 P21 LRCLK0/SPDIF_IN1 R1186 13