Conmix LTD.: Ultimate Sparkling Finish..

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

CONMIX LTD.

DECORATIVE PLASTER - GLITTERLITE®


Ultimate sparkling finish...
Glitterlite is a dry pre mix, decorative finish for internal and external use, giving a sparkling effect due to incorporated
glass, silica sand and marble chips. These aggregates remain exposed on the surface by using a special application
technique. The ultimate decorative coat for an impressive appearance and high weather resistance. Available in various
colours and three exciting textures i.e. glass, silica, glass & silica.

TECHNICAL DATA APPLICATION METHOD

Composition : White Portland Cement graded marble chips, silica BACKGROUND

sand or glass chips, non- fading colour pigments & It is recommended that Decorative
Plaster Glitterlite be applied over a
chemical improving agents
Portland Cement based render
Binder : White Portland Cement mix type-II (BSEN 13914-1) which
is combed to provide a
Aggregate Size : 3 mm
rough/keyed background. Where
Appearance : Granular powder, available in various colours the render is to be applied over
dissimilar backgrounds i.e.
Mixing Ratio : 7.5 ltrs of water per 50 kg bag.
concrete and block work (prior to
Water/Powder Ratio = 0.15 the application of Glitterlite), it is
important that the substrates are
Approx. Yield/Coverage * : 31 ltrs per 50 kg bag; 4.5 m2 per 50 kg bag at 5 mm
sound, free of undue shrinkage,
thickness structural, tensile and thermal
movements. The rendered
Density * : Wet : 1.80 kg/ltr Dry: 1.75 kg/ltr
background should be cured with
Compressive Strength * : 7 N/mm2 @ 28 days water for a period of 2 days (3-4
times daily) and allowed to harden
Flexural Strength * : 1.5 N/mm2 @ 28 days for at least 7 days before applying
Pack Size : 50 kg paper bags Glitterlite.
Glitterlite Pre-application
Shelf Life : 12 months from date of production when stored
The background for application of
under dry conditions Glitterlite should be clean, free of
Working Time : Approx. 40 Minutes dust deposits, loose mortar,
chemical impurities (salts and
Curing : Minimum 48 hours by potable water mist spray sulphates) and other
contaminations, which may
Specification : BS5492, BSEN998-1, BSEN13914-1 &
adversely affect adhesion and
BSEN13914-2:2005 cause variation in colour of the
Glitterlite.
* Typical results under laboratory condition
Cont...

Application tools

31 PMP/Glitterlite/ Ver2/04/10
It is essential to neutralize the suction of the background before Glitterlite is applied. This is done by applying potable water evenly on
the background plaster. A short time should elapse to allow the free water to disperse before applying Glitterlite. On no account should
Glitterlite be applied over wet backgrounds as this will cause de-bonding and variation in colour of the finished product.

MIXING
Glitterlite supplied in 50 kg has to be mixed with potable water only, in a clean plastic bucket or clean non-corrosive, uncontaminated
metal tub. To ensure a homogeneous and uniform mix, an electric agitator must be used. The amount of water to be added is approx.
7.5 ltrs per 50 kg bag (i.e. approximately 15% by weight) and should be constant for every batch. Add Glitterlite to water, turn the contents
of the bag carefully adding small amounts at a time into the container. Stir frequently and mix each batch for the same period of time.
Once mixed, allow to stand for 5 minutes and mix again before applying. (To avoid segregation, the Glitterlite should not be allowed to
stand for more than 40 minutes). No further water should be added to the mix. Hard and set plaster should not be re-mixed or used.

APPLICATION
Apply a thin coat of Glitterlite to an approximate thickness of 5 mm onto the prepared surface with a steel trowel. To avoid grinning, double
back and fill out to a uniform thickness. Work from a wet unset edge to complete an entire unbroken panel area in one continuous
operation. Level off with a aluminum straight edge. Using a steel trowel in conjunction with a wood float, bring to a fine surface. As soon
as the Glitterlite begins to stiffen, the surface should be slightly dampened, then closed with a flat steel trowel. To avoid joints and
discoloration, the material should be uniformly, troweled, levelled, straight and plumb before starting the next operation. When the
troweled surface has become firm (indentations cannot be made by finger pressure), using a felt roller, dipped in potable water, carefully
work the surface in an all over direction from top to bottom giving equal attention to the entire area. This will remove the thin film of the
cement from the surface, leaving the partly exposed glass or aggregate chips revealed on the surface. Drying out period would depend
on ambient weather conditions. To achieve an extreme sparkling effect of the Glitterlite, the surface has to be washed once, after 24
hours, with diluted hydrochloric acid to remove the fine film of cement from the glass chips.

Conmix demonstration team will assist in these procedures upon request.

SPECIAL NOTES
Glitterlite has to be protected from direct wind, sunlight and rain during application. It is recommended to erect a screen over the entire
area where the Glitterlite is to be applied. Once Glitterlite has been applied, care should be taken to ensure that the combined water is
retained for a minimum period of 48 hours for the purpose of hydration of the cement. The applied Glitterlite has to be water cured for
at least 2 days (3-4 times daily) by applying a fine mist spray of potable water over the entire surface. Glitterlite must only be applied in
panels measuring no more than 10m2. Expansion, movement and control joints between panels can be formed by fixing wooden battens
approx. 5 mm in thickness, which should be removed when the plaster has sufficiently hardened. The expansion joints should be filled
with a suitable sealant. Alternately, PVC render beads (fixed back to back) or expansion beads can be used. The shape of the panels
will depend on the individual's own design or will be determined by the expected movements of the structure. Special attention must be
paid to ensure that moisture does not penetrate behind the Glitterlite or backing coat. No open edges are permitted. Sealed joints,
flashing or other architectural details should be provided.

STORAGE
Conmix Glitterlite must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected. In areas of
high pollution or other contaminations, the cleaning of the surface of Glitterlite can be made easy by the application of Conmix
MoyaShield SR.

PMP/Glitterlite/ Ver2/04/10 32
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the
product as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defect and are manufactured and sold to Conmix standard terms and conditions of sale.

You might also like