32 Service Manual - Packard Bell - Easynote Lj75 Lj77

www.SoporteTecnicoBsAs.com.
ar
Repuestos para tus equipos.

Al mejor precio.
Envios a Todo el Pais

Packard Bell EasyNote LJ75/LJ77
Service Guide
Service guide files and updates are available

on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
VI
Table of Contents
System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Your Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Keyboard Area (selected models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
TouchPad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Key Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
System Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
System Utilities 27
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Remove HDD/BIOS Password Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Machine Disassembly and Replacement 49
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Removing the SD dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the Primary HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Removing the Secondary HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the Media Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
VII
Table of Contents
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Removing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Removing the Media Board FFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Removing the LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Removing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Removing the Modem Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Removing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Removing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Removing the RJ-11 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Removing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . .101
Removing the Microphone Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Replacing the Antennas, Power Board, and MIC . . . . . . . . . . . . . . . . . . . . . . .106
Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Replacing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Replacing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Replacing the RJ-11 Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Replacing the USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Replacing the Modem Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Replacing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Replacing the LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Replacing the Media Board FFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Replacing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Replacing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Replacing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Replacing the Media Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Replacing the Hard Disk Drive Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Replacing the SD Dummy Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Troubleshooting 139
Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
VIII
Table of Contents
Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
TouchPad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Internal Microphone Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
USB (Right Side) Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Bluetooth Function Test Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Easy Button Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
Motherboard CMOS Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Post Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Chipset POST Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Sec: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
Memory: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
BDS & Specific action: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
Each PEIM entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
Each Driver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
Each SmmDriver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . .167
Jumper and Connector Locations 169
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
LS-5022P USB Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
LS-5024P Cap Sensor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
LS-5026P LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
LS-5027P SW Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
FRU (Field Replaceable Unit) List 177
Packard Bell EasyNote LJ75/LJ77 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . .178
Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178
Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
Packard Bell EasyNote LJ75/LJ77 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188
Model Definition and Configuration 190
Packard Bell EasyNote LJ75 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .190
Packard Bell EasyNote LJ77 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
Test Compatible Components 201
Microsoft® Windows® 7 Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
IX
Table of Contents
Online Support Information 207
Index 209
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many features:
NOTE: Specifications denoted with an asterisk (*) vary depending on the model.
Operating System
• Genuine Windows® 7 Home Premium 64-bit*
• Genuine Windows® 7 Home Basic 64-bit*
Platform
• Intel® Core™ i7-620M processor (4 MB L3 cache, 2.66 GHz with Turbo Boost up to 3.33 GHz,
DDR3 1066 MHz, 35 W), supporting Intel® 64 architecture, Intel® Smart Cache*
• Intel® Core™ i5-430M/i5-520M/i5-540M processor (3 MB L3 cache, 2.26/2.40/2.53 GHz with
Turbo Boost up to 2.53/2.93/3.06 GHz, DDR3 1066 MHz, 35 W), supporting Intel® 64 architecture,
Intel® Smart Cache*
• Intel® Core™ i3-330M/i3-350M processor (3 MB L3 cache, 2.13/2.26 GHz, DDR3 1066 MHz, 35
W), supporting Intel® 64 architecture, Intel® Smart Cache*
• Mobile Intel® HM55 Express Chipset
System Memory
• Dual-channel DDR3 SDRAM support:
• Up to 4 GB of DDR3 1066 MHz memory, upgradeable to 8 GB using two soDIMM modules*
Display
• 15.6" HD 1600 x 900 pixel resolution, high-brightness (220-nit) TFT LCD with Diamond View
Technology, supporting simultaneous multi-window viewing
• 16:9 aspect ratio
• 8 ms response time
Graphics*
• ATI Mobility Radeon™ HD 56506 with up to 4091 MB of HyperMemory™ (1024 MB of dedicated
DDR3 VRAM, up to 3067 MB of shared system memory), supporting Unified Video Decoder
(UVD), OpenEXR High Dynamic-Range (HDR) technology, Shader Model 5.0, Microsoft®
DirectX® 11, OpenGL® 3.1, OpenCL™ 1.1
• ATI Mobility Radeon™ HD 54706 with up to 3579 MB of HyperMemory™ (512 MB of dedicated
DDR3 VRAM, up to 3067 MB of shared system memory), supporting Unified Video Decoder
(UVD), OpenEXR High Dynamic-Range (HDR) technology, Shader Model 5.0, Microsoft®
DirectX® 11, OpenGL® 3.1, OpenCL™ 1.1
• Intel® Core i7-620M/i5-540M/i5-520M/i5-430M/i3-350M/ i3-330M processor with Intel® Graphics
Media Accelerator HD7 (Intel® GMA HD), 128 MB of dedicated system memory, Microsoft®
DirectX® 10
Chapter 1 1
• Dual independent display support
• 16.7 million colors
• External resolution / refresh rates*:
• VGA port up to 2048 x 1536: 85 Hz
• HDMI™ port up to 1920 x 1200: 60 Hz
• MPEG-2/DVD decodingVC-1 and H.264 (AVC) decodingMicrosoft® DirectX Video Acceleration
(DXVA) application interface (API)
• HDMI™(High-Definition Multimedia Interface) with HDCP (High-bandwidth Digital Content
Protection) support
Storage subsystem*
• One or two 160/250/320/500/640 GB or larger hard disk drives
• Multi-in-1 card reader, supporting:
• Secure Digital™ (SD) Card, MultiMediaCard (MMC), Memory Stick™ (MS), Memory Stick
PRO™ (MS PRO), xD-Picture Card™ (xD)
Optical Drive*
• 4X Blu-ray Disc™/DVD-Super Multi double-layer drive:
• Read: 24X CD-ROM, 24X CD-R, 24X CD-RW, 8X DVD-ROM, 8X DVD-R, 8X DVD+R, 8X
DVD-ROM DL, 6X DVD-R DL, 6X DVD+R DL, 8X DVD-RW, 8X DVD+RW, 5X DVD-RAM, 4X
BD-ROM, 4X BD-R, 2X BD-RE, 4X BD-ROM DL, 4X BD-R DL, 2X BD-RE DL
• Write: 24X CD-R, 16X CD-RW, 8X DVD-R, 8X DVD+R, 6X DVD-RW, 6X DVD+RW, 5X DVD-
RAM, 4X DVD+R DL, 4X DVD-R DL
• 8X DVD Super Multi double-layer drive:
• Read: 24X CD-ROM, 24X CD-R, 24X CD-RW, 8X DVD-ROM, 8X DVD-R, 8X DVD+R, 6X
DVD-ROM DL, 6X DVD-R DL, 6X DVD+R DL, 6X DVD-RW, 6X DVD+RW, 5X DVD-RAM
• Write: 24X CD-R, 16X CD-RW, 8X DVD-R, 8X DVD+R, 4X DVD-R DL, 4X DVD+R DL, 6X
DVD-RW, 8X DVD+RW, 5X DVD-RAM
Audio
• Two built-in stereo speakers
• High-definition audio support
• S/PDIF (Sony/Philips Digital Interface) support for digital speakers
• Built-in microphone
• MS-Sound compatible
Dimensions and Weight

• 372 (W) x 259 (D) x 26/37 (H) mm (14.66 x 10.19 x 1.02/1.46 inches)
• 2.65 kg (5.84 lbs.) with 6-cell battery
Communication
• Video conferencing solution, featuring:
• Webcam with 640 x 480 resolution
• WLAN*:
2 Chapter 1
• 802.11b/g/n Wi-Fi CERTIFIED™
• 802.11b/g Wi-Fi CERTIFIED™
• WPAN*: Bluetooth® 2.1+EDR
• LAN: Gigabit Ethernet, Wake-on-LAN ready
• Modem: 56K ITU V.92 with PTT approval*
Privacy control
• BIOS user, supervisor, HDD passwords
• Kensington lock slot
Power
• ACPI 3.0 CPU power management standard: supports Standby and Hibernation power-saving
modes
• 4400 mAh 6-cell Li-ion battery pack with integrated graphics:
• 3-hour 10-minute battery life*
• 3-pin 65 W AC adapter
• 4400 mAh 6-cell Li-ion battery pack with discrete graphics:
• 2-hour 50-minute battery life*
• 3-pin 90 W AC adapter
• ENERGY STAR®
Special Keys and Controls

• 99-/100-/103-key keyboard
• Multi-gesture touchpad, supporting two-finger scroll, pinch, rotate, flip
• Nine function keys, four cursor keys, Windows® key, international language support
• Capacitive-touch launch keys: programmable, backup, touchpad lock, WLAN, volume up/down/
mute
I/O Ports
• Multi-in-1 card reader
• Four USB 2.0 ports
• HDMI™ port with HDCP support*
• External display (VGA) port
• Headphone/speaker/line-out jacks with S/PDIF support
• Microphone-in jack
• Ethernet (RJ-45) port
• Modem (RJ-11) port*
• DC-in jack for AC adapter
Software*
• Packard Bell Customer Registration
• Packard Bell Identity Card
Chapter 1 3
• Packard Bell InfoCentre
• Packard Bell MyBackup Solution
• Packard Bell Recovery Management
• Packard Bell Updater
• Adobe® Flash® Player 9
• Adobe® Photoshop® Elements 7
• Adobe® Reader® 9
• CyberLink® Blu-ray Disc™ / DVD Solution™, featuring PowerDVD™eBay® desktop shortcut
• Google Toolbar™
• Metaboli linkMicrosoft® Works with Office Home and Student 2007 Trial
• Nero® 9 EssentialsNorton Internet Security™ 2009 Trial (60 days)
• Windows Live™ Essentials
Optional
• Bluetooth® 2.1 module1 GB / 2 GB / 4 GB DDR3 1066 MHz soDIMM module
• 4400 mAh 6-cell Li-ion battery pack
• 3-pin 90 W AC adapter (discrete)
• 3-pin 65 W AC adapter (integrated)
Environment
• Temperature:
• Operating: 5 °C to 35 °C
• Non-operating: -20 °C to 65 °C
• Humidity (non-condensing):
• Operating: 20% to 80%
• Non-operating: 20% to 80%
4 Chapter 1
System Block Diagram
Chapter 1 5
Your Notebook tour
NOTE: Port placement may vary depending on the model.
Front View
Component Icon Description
6 Chapter 1
Left View
1
7
2 3 4 5 6
No. Component Icon Description

1 Kensington™ Secure your notebook to an object by connecting a
lock slot Kensington cable lock to this slot.
2 Monitor port Plug an analog VGA monitor or projector into this port.
3 Ethernet jack Plug an Ethernet network cable into this jack. Plug the other
end of the cable into a cable modem, DSL modem, or an
Ethernet network jack.
4 HDMI out jack HDMI HDMI Plug an HDMI device, such as a high definition
television, into this optional jack.
5 Microphone jack Plug a microphone into this jack.
6 Headphone jack Plug amplified speakers or headphones into this jack. The
built-in speakers are turned off when speakers or
headphones are plugged into this jack.
• Headphone with SPDIF support
7 USB port Plug USB devices (such as a diskette drive, flash drive,
printer, scanner, camera, keyboard, or mouse) into these
ports.
Chapter 1 7
Right View
2
1 3
No. Component Icon Description

1 Blu-Ray Disc Insert CDs or DVDs into this drive.
Drive
2 USB ports (2) Plug a USB device (such as a diskette drive, flash drive,
printer, scanner, camera, keyboard, or mouse) into this
port.
3 Power button Press to turn the power on or off. You can also configure
the power button for Sleep/Resume mode.
Rear View

Ventilation fan Helps cool internal components.
Warning: Do not work with the notebook resting on your
lap. If the air vents are blocked, the notebook may become
hot enough to harm your skin.
Caution: Do not block or insert objects into these slots. If
these slots are blocked, your notebook may overheat
resulting in unexpected shutdown or permanent damage to
the notebook.
Caution: Provide adequate space around your notebook
so air vents are not obstructed. Do not use the notebook on
a bed, sofa, rug, or other similar surface.
8 Chapter 1
Bottom View

Battery Provides power when the notebook is not plugged into AC
power.
Battery lock Slide to unlock the battery.
Battery latch Slide to release the battery.
Memory bay Memory modules are located in this bay.
Hard drive bay The hard drive is located in this bay.
Ventilation slots Helps cool internal components.

and cooling fan Warning: Do not work with the notebook resting on your
lap. If the air vents are blocked, the notebook may become
hot enough to harm your skin.
Caution: Do not block or insert objects into these slots. If
these slots are blocked, your notebook may overheat
resulting in unexpected shutdown or permanent damage to
the notebook.
Caution: Provide adequate space around your notebook
so air vents are not obstructed. Do not use the notebook on
a bed, sofa, rug, or other similar surface.
Chapter 1 9
Keyboard Area (selected models)
No. Component Description

1 Capacitive touch Press to access capacitive touch key function.
keys
2 Touchpad Provides all the functionality of a mouse.
10 Chapter 1
LCD Panel
No. Component Description

1 Display 15.6" HD 1600 x 900 pixel resolution, high-brightness (220-
nit) TFT LCD with Diamond View Technology
2 Webcam Use to let others see who they are communicating with
when making VoIP calls.
Chapter 1 11
Status Indicators
Status indicators inform you when a drive is being used or when a button has been pressed that affects how
the keyboard is used. The status indicators are located below the screen.
Bluetooth Num lock Battery

HDD Caps lock Power
Indicator Icon Description
Bluetooth • LED on - Bluetooth communication is turned on
• LED off - Bluetooth communication is turned off
Hard drive or disk • LED blinking - The drive is being accessed
drive • LED off - The drive is not being accessed
Num lock • LED on - Num lock is turned on

• LED off - Num lock is turned off
Caps lock • LED on - Caps lock is turned on
• LED off - Caps lock is turned off
Battery charge • LED blue - Battery is fully charged
indicator • LED red - Battery is charging
Important: This LED only lights up when your notebook is
connected to AC power.
Power indicator • LED on - Notebook is on.
• LED blinking - Notebook is in Sleep or Hybrid Sleep mode.
• LED off - Notebook is off.
12 Chapter 1
TouchPad Basics
The following items show you how to use the TouchPad:
2 3
• Move your finger across the TouchPad (1) to move the cursor.
• Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the TouchPad is the same as clicking the left button.
Function Left Button (2) Right Button (3) Main TouchPad (1)
Execute Quickly click twice. Tap twice (at the same speed
as double-clicking a mouse
button).
Select Click once. Tap once.
Drag Click and hold, then use Tap twice (at the same speed
finger on the TouchPad to as double-clicking a mouse
drag the cursor. button); rest your finger on
the TouchPad on the second
tap and drag the cursor.
Access Click once.
context menu
NOTE: When using the TouchPad, keep it - and your fingers - dry and clean. The TouchPad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not
increase the TouchPad’s responsiveness.
Chapter 1 13
Using the Keyboard
Your notebook features a full-size keyboard that functions the same as a desktop computer keyboard. Many of
the keys have been assigned alternate functions, including shortcut keys for Windows, function keys for
specific system operations, and the Num Lock keys for the numeric keypad.
2 3 4 5 6
Key Types
The keyboard has several different types of keys. Some keys perform specific actions when pressed alone
and other actions when pressed in combination with another key.
No. Icon Key Type Description

Function keys Press these keys labeled F1 to F12 to perform actions in
programs. For example, pressing F1 may open help. Each
program uses different function keys for different purposes.
1 See the program documentation to find out more about the
function key actions.
System keys Press these colored keys in combination with the Fn key to
perform specific actions. See “System Keys” on page 16.
Fn key Press the Fn key in combination with a colored system key to
2
perform a specific action.
3 Windows key Press this key to open the Windows Start menu. This key
can also be used in combination with other keys to open
utilities. See “Windows Keys” on page 15.
4 Application key Press this key for quick access to shortcut menus and help
assistants in Windows.
5 Arrow keys Press these keys to move the cursor up, down, right, or left.
Navigation keys Press these keys to move the cursor to the beginning of a line,
6 to the end of a line, up the page, down the page, to the
beginning of a document, or to the end of a document.
14 Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
< >: Open or close the Start menu
< > + <D>: Display the desktop
< > + <E>: Open Windows Explore
< > + <F>: Search for a file or folder
< > + <G>: Cycle through Sidebar gadgets
< > + <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
< > + <M>: Minimizes all windows
< > + <R>: Open the Run dialog box
< > + <T>: Cycle through programs on the taskbar
< > + <U>: Open Ease of Access Center
< > + <X>: Open Windows Mobility Center
< > + <BREAK>: Display the System Properties dialog box
< > + <SHIFT+M>: Restore minimized windows to the desktop
< > + <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D
< > + <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
<CTRL> + < > + <F>: Search for computers (if you are on a network)
<CTRL> + < >
+ <TAB>: Use the arrow keys to cycle through programs on the
taskbar by using Windows Flip 3-D
Note: Depending on your edition of Windows 7, some shortcuts may not function as
described.
Chapter 1 15
System Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, Bluetooth and WiFi.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Function Key Description

Turn the capacitive touch key LEDs on or off.
Enter Sleep mode or Hybrid Sleep mode. Press the power button to leave Sleep
mode.
Toggle the notebook display in the following order: The LCD. An external monitor
or projector (a monitor or projector must be plugged into the monitor port or
HDMI port on your notebook). Both displays at the same time.
Turn the optional Bluetooth radio on or off. Warning: Radio frequency wireless
communication can interfere with equipment on commercial aircraft. Current
aviation regulations require wireless devices to be turned off while traveling in an
airplane. Bluetooth communication devices are examples of devices that provide
wireless communication. Important: The wireless network switch must be in the
ON position for this button to work.
Mute the sound. Press the key combination again to restore the sound.
Turns the display screen backlight off to save power. Press any key to return.
Play/ Pause—Plays or pauses the CD or DVD.
Stop—Stops playing the CD or DVD.
Previous—Skips back one CD track or DVD chapter.
Next—Skips ahead one CD track or DVD chapter.
16 Chapter 1
Hardware Specifications and Configurations
Processor
Item Specification
CPU Intel Mobile Calpella rPGA988A
Core Logic Intel Ibex Peak-M (HM55)
Power See table below
On-die Cache • A 32-KB instruction and 32-KB data first-level cache (L1) for each core
• A 256-KB shared instruction/data second-level cache (L2) for each core
• Up to 4-MB shared instruction/data third-level cache (L3), shared among all
cores
Front Side Bus See table below
Processor Specifications
CPU Bus Cache Core
Item Cores Package Acer P/N
Speed Speed Size Voltage
Ci3330M 2.13 GHz 2 330 M 3 MB PGA 35 W KC.33001.DMP
Ci5430M 2.26 GHz 2-4 430 M 3 MB PGA 35 W KC.43001.DMP
CPU Fan True Value Table)

(DIS)
CPU Temperature Fan Speed SPL Spec
Core 0 Core 1 Core 2 Core 3 (RPM) (dBA)
48 48 48 48 2400 28
60 60 60 60 2900 31
70 70 70 70 3100 34
85 85 85 85 3400 37
99 99 99 99 3700 40
104 104 104 104 3700 40
Throttling 50%: On= 99°C; OFF=88°C
OS shut down at 104°C; H/W shut down at 92°C
(UMA)
CPU Temperature
Fan Speed (RPM) SPL Spec (dBA)
Core 0 Core 1 Core 2 Core 3
48 48 48 48 2600 28
60 60 60 60 2800 31
70 70 70 70 3100 34
85 85 85 85 3400 37
99 99 99 99 3800 40
104 104 104 104 3800 40
Throttling 50%: On= 99°C; OFF=88°C
OS shut down at 104°C; H/W shut down at 92°C
Chapter 1 17
Northbridge
Item Specifications
Chipset Intel Ibex Peak-M (HM55)
Features • Dual-channel DDR3 1066 MHz memory support
• Serial ATA
• Hi-Speed USB 2.0 connectivity
BIOS
Item Specification
BIOS vendor Insyde H20
BIOS Version V0.07
BIOS ROM type Flash
Features • Flash ROM 1MB
• Support ISIPP
• Support Acer UI
• Support multi-boot
• Suspend to RAM (S3)/Disk (S4)
• Various hot-keys for system control
• Support SMBUS 2.0, PCI2.3
• ACPI 2.0 compliance with Intel Speed Step Support C1, C2,
C3, C4,C6 and S3, S4 for mobile CPU
• DMI utility for BIOS serial number configurable/asset tag
• Support PXE
• Support Y2K solution
• Support Win Flash Wake on LAN from S3
• Wake on LAN form S4 in AC mode
• System information
System Memory
Item Specification
Memory controller Intel HM55
Memory size 4 GB
DIMM socket number 2
Supports memory size per socket 4 GB (4 GB for 64-bit OS)
Supports maximum memory size 8 GB (8 GB for 64-bit OS)
Supports DIMM type DDRIII
Supports DIMM Speed 1066 MHz
Supports DIMM voltage 1.5V
Cache 3-4 MB L3
18 Chapter 1
Memory Combinations
Slot 1 Slot 2 Total Memory
0MB 512MB 512MB
0MB 1024MB 1024MB
0MB 2048MB 2048MB
512MB 512MB 1024MB
512MB 1024MB 1536MB
512MB 2048MB 2560MB
1024MB 0MB 1024MB
1024MB 512MB 1536MB
1024MB 1024MB 2048MB
1024MB 2048MB 3072MB
2048MB 0MB 2048MB
2048MB 512MB 2560MB
2048MB 1024MB 3072MB
2048MB 2048MB 4096MB
4096MB 4096MB 8192MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
Graphics Controller
Item Specification
VGA Chip ATI Mobility Radeon™ HD ATI Mobility Radeon™ HD Intel® Graphics Media
5650 5470 Accelerator HD7 (Intel®
GMA HD)
Graphics 1024 MB of dedicated 512 MB of dedicated DDR3 128 MB of dedicated
Memory DDR3 VRAM, up to 3067 VRAM, up to 3067 MB of system memory
MB of shared system shared system memory
memory
Supports • Unified Video Decoder • Unified Video Decoder • Microsoft® DirectX® 10
(UVD) (UVD)
• OpenEXR High • OpenEXR High Dynamic-
Dynamic-Range (HDR) Range (HDR) technology
technology • Shader Model 5.0
• Shader Model 5.0 • Microsoft® DirectX® 11
• Microsoft® DirectX® 11 • OpenGL ® 3.1
• OpenGL ® 3.1 • OpenCL™ 1.1
• OpenCL™ 1.1
Resolution External resolution / refresh rates:
• VGA port up to 2048 x 1536: 85 Hz
• HDMI™ port up to 1920 x 1200: 60 Hz
Features • Dual independent display support
• 16.7 million colors
• MPEG-2/DVD decoding
• VC-1 and H.264 (AVC) decoding
• Microsoft® DirectX Video Acceleration (DXVA) application interface (API)
• HDMI™ (High-Definition Multimedia Interface) with HDCP (High-bandwidth Digital
Content Protection) support
Chapter 1 19
LAN Interface
Item Specification
LAN Chipset Broadcom BCM57780
LAN connector type RJ45
LAN connector location Left side
Features Support for 10/100/1000*
*Check model number for specifications.

Wireless Module 802.11b/g
Item Specification
Manufacturer/Model • Realtek 8192SE
• Atheros HB93
Bluetooth
Item Specification
Model Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/
w:861
Hard Disk Drive Interface

Item Specification
Vendor Seagate
Capacity (MB) 250 500
Bytes per sector 512
Data heads 2/4

Drive Format
Disks 2 2
Spindle speed (RPM) 5,400
Performance Specifications
Buffer size 8 MB
Interface SATA
Internal transfer rate (Mbits/sec max) 830 1175
I/O data transfer rate (Mbytes/sec max) 300
DC Power Requirements
Voltage tolerance 5V(DC) +/- 5%
20 Chapter 1
Item Specifications
Vendor & Model Name Toshiba
Capacity 250GB
Data heads 4/2
Drive Format
Disks 2/1
Spindle speed (RPM) 5400
Buffer size 8MB
Interface SATA
Internal transfer rate (Mbits/sec, max) 363 ~ 952 typical
I/O data transfer rate 3Gbits/s
Voltage +5.0V ± 5%.
Item Specifications
Vendor & Model Name HGST
Capacity (MB) 500 320 250 160
Data heads 4 3 2 2
Drive Format
Disks 2 2 1 1
Buffer size 8MB
Interface SATA
Internal transfer rate 875 MB/s 845 MB/s
I/O data transfer rate 3 GB/s
Voltage +5.0V ± 5%
Item Specifications
Vendor & Model Name WD
Capacity (MB) 160 320 640
Data heads 2 3 4
Drive Format
Disks 1 2 2
Buffer size 8 MB
Interface SATA
Chapter 1 21
Item Specifications
Internal transfer rate (Mbits/
sec, max)
I/O data transfer rate 3 GB/s
Voltage +5.0V ± 5%
22 Chapter 1
Super-Multi Drive Module
Item Specification
Vendor & model name HLDS/GSA-T50, Toshiba Digi/TS-L633A
Performance Specification With CD Diskette With DVD Diskette
Transfer rate (MB/sec) Sustained: Sustained:
Max 3.5 Mbytes/sec Max 10 Mbytes/sec
Buffer Memory 2MB
Interface SATA
Applicable disc format Applicable media types:
Writing:
Confirms to DVD+R Version 1.2 and DVD+RW Version 1.3 / DVD+R DL
Version 1.0 /DVD-R Version 2.0 / DVD-RW Version 1.2 / DVD-R DL Version
3.0.
Reading:
DVD single/dual layer (PTP, OTP), DVD-R single/dual layer
DVD+R single/double layer
DVD-RW
DVD+RW
CD-DA
CD-ROM
CD-ROM/XA
Photo-CD, Multi-session, Video CD
CD-I FMV, CD Extra, CD Plus, CD-R, and CD-RW
Loading mechanism Drawer (Solenoid Open)
Tact SW (Open)
Emergency Release (draw open hole)
Power Requirement
Input Voltage DC 5 V +/- 5%
Item Specification
Vendor & model name SONY AD-7583S
3650 (max.) 10,993 (max.)
Buffer Memory 2 MB
Interface SATA
Applicable disc format Write:
DVD Data & Video
CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2,
CD-i, Video-
CD, CD-Text
Read:
DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-Video, DVD-Audio,
SACD (Hybrid), UDF DVD, DVD-R, DVD-R DL, DVD-R 3.95 GB, DVD-R
Authoring, DVD-R Multi-Border, DVD-RW, DVD+R, DVD+R DL, DVD+R Multi-
Session, DVD+RW, DVD-RAM V1.0, DVDRAM V2.0 & 2.1 & 2.2
CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2,
CD-i, CD-i Bridge, Video-CD (MPEG-1), Karaoke CD, Photo-CD, Enhanced
CD, CD Plus, CD Extra, itrax CD, CD-Text, UDF CD, CD-R, and CD-RW
Chapter 1 23
Item Specification
Loading mechanism Drawer (Solenoid Open)
Tact SW (Open)
Emergency Release (draw open hole)
Power Requirement
Blue-Ray Combo Drive Module
Item Specification
Vendor & model name Sony BC-5500S
Max 2.4 Mbytes/sec Max 11 Mbytes/sec
Buffer Memory 4.5 MB
Interface SATA
Applicable disc format Applicable media types:
BD-ROM (Single and Dual Layer)
BD-R (Single and Dual Layer)
BD-RE (Single and Dual Layer)
DVD-ROM (Single and Dual Layer)
DVD+R (Single and Double Layer)
DVD-R (Single and Dual Layer)
DVD+RW (Single Layer) and DVD-RW (Single Layer) discs
DVD-RAM (Ver.2)
CD-ROM
CD-R
CD-RW
Loading mechanism Drawer (Solenoid Open), Tact SW (Open), Emergency Release (draw
open hole)
Power Requirement
Item Specification
Vendor & model name PLDS BD Combo DS-4E1S
Performance Specification With CD Diskette With DVD Diskette Blueray
Transfer rate (KB/sec) Sustained: Sustained: Sustained:
3,500 (min.) 10,000 (min.) 18,000 (min.)
Buffer Memory 2 MB
Interface SATA
Applicable disc format CD-DA, CD-TEXT, CD ROM Mode-1, CD-ROM/XA Mode-2 Form-1
and Form-2, CD-I Ready, Video-CD (MPEG-1), Photo-CD, Enhance
CD, CD extra, I-Trax CD and UDF DVD-ROM, DVD-Video, DVD-Audio,
DVD-R single/multi border(s) DVD+R single/multi session(s) DVD-RW
DVD+RW DVD-RAM BD-ROM ver2.0, UDF2.5 BD-R ver1.0 and
ver2.0, UDF2.5 BD-RE ver2.0 and ver3.0, UDF2.5 BD-hybrid (only BD
part)
Loading mechanism Drawer (Solenoid Open), Tact SW (Open), Emergency Release (draw
open hole)
Power Requirement
24 Chapter 1
Audio Interface
Item Specification
Audio Realtek ALC272 Azalia Codec and Amplifier G1454
Controller
• Features • HD Audio
• SNR > 85,High-performance DACs with 95dB SNR (A-Weighting), ADCs with
85dB SNR (A-Weighting)
• Internal Digital Microphone
• Two speakers, max. 1W output for each
• Meets performance and function requirements for Microsoft WLP 3.10, and stricter
performance requirements for future WLP
• Two stereo DAC support 16/20/24-bit PCM for two independent playback (multiple
streaming)
• Two stereo ADC supports 16/20/24-bit PCM format for two independent recording
• All DACs support independent 44.1k/48k/96k/192kHz sample rate
• All ADCs support independent 44.1k/48k/96k/192kHz sample rate
• Two independent SPDIF outputs support 16/20/24-bit format and 44.1k/48k/88.2k/
96k/192kHz rate
• All analog jack ports except MONO, BEEP-IN and HP-OUT are stereo input and
output re-tasking
• Supports line level mono output
• Supports analog PCBEEP input, and features an integrated digital BEEP
generator
• Support two stereo digital microphone input for microphone array AEC/BF
application
• Each stereo digital microphone interface has its own clock output to support
independent sample rate
• Supports legacy analog mixer architecture
• Built-in five headphone amplifiers on port-A and port-D, port-E, port-F and port-I.
• Headphone amplifier on port-I (HP-OUT) is designed to drive output without
external DC blocking capacitors
• Software selectable 2.5V and 3.2V reference output for microphone bias
• Software selectable boost gain (+10/+20/+30dB) for analog microphone input
• Two jack detection pins; each supports detection of up to 4 jacks
• Supports two GPIO (General Purpose Input/Output) pins (pin sharing with digital
microphone interface)
• Supports EAPD (External Amplifier Power Down) control for external amplifier
• Supports anti-pop mode when analog power AVDD is on and digital power is off
• Supports 1.5V~3.3V scalable I/O for HD Audio link
• 48-pin LQFP ‘Green’ package
Power and Keyboard Controller

Item Specification
Controller KB926
Total number of keypads 99-/100-/103
Windows logo key Yes
Internal & external keyboard Yes
work simultaneously
Features Support Application keys for Windows XP version
Chapter 1 25
Battery
Specification
Item
6 Cell 8 Cell
Vendor & model name PANASONIC AS-2007B SANYO AS-2007B
SAMSUNG AS-2007B SIMPLO AS-2007B
SANYO AS-2007B SONY AS-2007B
Battery Type Li-ion Li-ion
Pack capacity 4400 mAh 4800 mAh
Normal Voltage 11.1V 14.8
Charge Voltage 12.6V 12.6V
Fast Charge Current 2.94~3.5A 3.1A
Package configuration 3S2P 4S2P
LCD 15.6”
Item Specification
Vendor/model name CMO/AUO/Samsung/LPL
Display resolution (pixels) 1600x900
Typical White Luminance (cd/m 2) 220
(also called Brightness)
Aspect Ratio 16:9
Electrical Interface LVDS
26 Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility

There are six menu options: Information, Main, Advanced, Security, Boot, and Exit.
Follow these instructions:
• To choose a menu, use the left and right arrow keys.
• To choose an item, use the up and down arrow keys.
• To change the value of a parameter, press F5 or F6.
• A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
• Press Esc while you are in any of the menu options to go to the Exit menu.
• In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
Chapter 2 27
Information
The Information screen displays a summary of your computer hardware information.
InsydeH20 Setup Utility Rev. 3.5

Information Main Advanced Security Power Boot Exit
CPU Type Intel® Core™ i7

CPU Speed 2.66GHz
HDD Model Name: Hitachi HTS545016B9A300

HDD Serial Number: 081211FB2203LNJHLVNA
HDD Model Name: None
HDD Serial Name:
ATAPI Model Name:
System BIOS Version: V0.07

VGA BIOS Version: Intel V1706
Serial Number:
Asset Tag Number:
Product Name: EasyNote LJ75/LJ77
Manufacturer Name: Packard Bell
UUID:
F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

ESC Exit Select Menu Enter Select SubMenu F10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ according to model.
The table below describes the parameters in this screen.
Parameter Description
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
HDD Model Name This field shows the model name of HDD installed on primary IDE
master.
HDD Serial Number This field displays the serial number of HDD installed on primary IDE
master.
ATAPI Model Name This field shows the model name of the Optical device installed in
the system.
System BIOS Version Displays system BIOS version.
VGA BIOS Version This field displays the VGA firmware version of the system.
Serial Number This field displays the serial number of this unit.
Asset Tag Number This field displays the asset tag number of the system.
Product Name This field shows product name of the system.
Manufacturer Name This field displays the manufacturer of this system.
UUID Universally Unique Identifier (UUID) is an identifier standard used in
software construction, standardized by the Open Software
Foundation (OSF) as part of the Distributed Computing Environment
(DCE).
28 Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.

Item Specific Help

System Time: [19:10:59]
System Date: [01/09/2009]
This is the help for the
Total Memory: 4095 MB hour field. Valid range
Video Memory: 512 MB is from 0 to 23.
INCREASE/REDUCE: F 5 / F 6
Quick Boot [Enabled]
Network Boot [Enabled]
F12 Boot Menu [Disabled]
D2D Recovery [Enabled]
SATA Mode [AHCI]

NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default
and suggested parameter settings.
Parameter Description Format/Option
System Time Sets the system time. The hours are displayed with 24- Format: HH:MM:SS
hour format. (hour:minute:second)
System Date Sets the system date. Format MM/DD/YYYY
(month/day/year)
Total Memory Displays the total memory available. N/A
Video Memory Displays the available memory for Video. N/A
Quick Boot Allows startup to skip certain tests while booting, Option: Enabled or
decreasing the time needed to boot the system. Disabled
Network Boot Enables, disables the system boot from LAN (remote Option: Enabled or
server). Disabled
F12 Boot Menu Enables, disables Boot Menu during POST. Option: Enabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The function Option: Enabled or
allows the user to create a hidden partition on hard disc Disabled
drive to store operation system and restore the system
to factory defaults.
SATA Mode Control the mode in which the SATA controller should Option: AHCI or IDE
operate.
Chapter 2 29
Advanced
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.

Item Specific Help

XBoot Configuration
XPeripheral Configuration
XIDE Configuration Configures Boot
XVideo Configuration Settings.
XUSB Configuration
XChipset Configuration
XACPI Table/Features Control
Express Card [Disabled]
XPCI Express Root Port 1
XASF Configuration

The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default
Parameter Description Submenu Items

Boot Configuration Enter the Boot Configuration menu. • Numlock
Peripheral Enter the Peripheral Configuration menu. • Serial Port A
Configuration • Infrared Port
• Azalia
• Lan
IDE Configuration Enter the IDE Configuration menu. • IDE Controller
• HDC Configure as
• AHCI Option ROM Support
• SATA Port 0, 1, 4, 5 HotPlug
• Channel 1 to 4 Master and Slave
30 Chapter 2
Video Enter the Video Configuration menu. • Render Standby
Configuration • IGD—Device2, Function1
• IGD—Pre-allocat Memory
• IGD—DVMT Size
• Clock Chip Initialize
• Enabled CK SSC
• IGD—Boot Type
• IGD—LCD Panel Type
• IGD—TV
• IGD—PAVP Mode
USB Configuration Enter the USB Configuration menu. • USB Legacy
• EHCI 1, 2
• UHCI 1 ~ 5
• Per-Port Control
• USB Port 0~11
Chipset Enter the Chipset Configuration menu. • Port 80h Cycles
Configuration • DMI Link ASPM Control
• Automatic ASPM
• PCI Latency Timer
• VT-d
• iTPM
ACPI Table/ Enter the ACPI Table/Features Control • FACP—C2 Latency Value
Features Control menu. • FACP—C3 Latency Value
• FACP—RTC S4 Wakeup
• APIC—IO APIC Mode
• HPET—HPET Support
• Base Address select
Express Card Disabled • N/A
PCI Express Root Enter the PCI Express Root Port Menu • PCI Express Root Port 1
Port 1 ~ 6 • VC1 Enable
• ASPM
• Automatic ASPM
• ASPML0s
• ASPM L1
• URR
• FER
• NFER
• CER
• CTO
• SEFE
• SENFE
• SECE
• PME Interrupt
• PMI SCI
• Hot Plug SCI
ASF Configuration Enter the ASF Configuration Menu • Mini WatchDog Timeout
• BIOS Boot Timeout
• OS Boot Timeout
• Power-on wait time
Chapter 2 31
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.

Item Specific Help

Supervisor Password Is: Clear
User Password Is: Clear
SATA Port0 Disk Status: Froze Install or Change the
password and the length
Set Supervisor Password of password must be less
Set User Password than eight words.
Set SATA Port0 HDD Password
Password on Boot [Disabled]

The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter Description Option
Supervisor Password Is Shows the setting of the Supervisor password Clear or Set
User Password Is Shows the setting of the user password. Clear or Set
SATA Port0 Disk Status Shows the status of the SATA Port0 disk. Froze or ?
Set Supervisor Password Press Enter to set the supervisor password. When set, N/A
this password protects the BIOS Setup Utility from
unauthorized access. The user can not either enter the
Setup menu nor change the value of parameters.
Set User Password Press Enter to set the user password. When user N/A
password is set, this password protects the BIOS Setup
Utility from unauthorized access. The user can enter
Setup menu only and does not have right to change the
value of parameters.
Set SATA Port0 HDD Enter HDD Password. N/A
Password
Password on Boot Defines whether a password is required or not while the Disabled or
events defined in this group happened. The following Enabled
sub-options are all requires the Supervisor password
for changes and should be grayed out if the user
password was used to enter setup.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
32 Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
Set Supervisor Password
Enter New Password [ ]

Confirm New Password [ ]
2. Type a password in the “Enter New Password” field. The password length can not exceed 8 alphanumeric
characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3. Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4. If desired, you can opt to enable the Password on boot parameter.
5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
Set Password box appears:
Enter Current Password [ ]

2. Type the current password in the Enter Current Password field and press Enter.
3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2 33
Changing a Password
Set Password box appears.
Enter Current Password [ ]

2. Type the current password in the Enter Current Password field and press Enter.
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4. Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5. If desired, you can enable the Password on boot parameter.
6. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
Setup Notice
Changes have been saved.
[Continue]
The password setting is complete after the user presses Enter.

If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
Setup Warning
Invalid Password.
[Continue]
If the new password and confirm new password strings do not match, the screen will display the following
message.
Setup Warning
Passwords do not match.

Re-enter password.
[Continue]
34 Chapter 2
Power
The Advanced screen allows the user to configure the various advanced BIOS options.
IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless
you have experience adjusting these items, we recommend that you leave these settings at the
default values. If making settings to items on these pages causes your system to malfunction or
prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to
boot up normally.

Item Specific Help

XAdvanced CPU Control
XPlatform Power Management
XBreak Event These items control
various CPU parameters.
ACPI S3: [Enabled]
Wake on PME [Enabled]
Wake on Modem Ring [Enabled]
Quickly S4 Resume [Disabled]
Auto wake on S5 [Disabled]

Chapter 2 35
The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default

Advanced CPU Enter the Advanced CPU Control menu. • P-States (IST)
Control • Boot performance mode
• Thermal Mode
• CMP Support
• Use XD capability
• VT Support
• SMRR Support
• C-States
• Enhanced C-States
• C-State Pop Up Mode
• C-State Pop Down Mode
• C4 Exit Timing Mode
• Deep C4
• Hard C4E
• Enable C6
• EMITM
• Bi-directional PROCHOT#
• Dynamic FSB Switching
• Turbmo Mode
• ACPI 3.0 T-States
• DTS
• DTS Calibration
• Thermal Trip Points Setting
Platform Power Enter the Platform Power Management • PCI Clock Run
Management menu.
Break Event Enter the Break Event menu • Storage Break Event
• PCIE Break Event
• PCI Break Event
• EHCI Break Event
• UHCI Break Event
• HDA Break Event
ACPI S3 Enable or Disable ACPI S1/S3 Sleep State. N/A
Wake on PME Disable or Enable wake up when the N/A
system power is off and a PCI Power
Management Enable wake up event occurs.
Wake on Modem Disable or Enable wake up when the N/A
Ring system power is off and a modem attached
to the serial port is ringing.
Quickly S4 Disable or Enable optional quick boot from N/A
Resume S4 Resume.
Auto wake on S5 Disable or Enable auto wake up by date N/A
and time or at a fixed time everyday.
36 Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Select Boot Devices to select specific devices to support boot.

Item Specific Help

Boot priority order:
1. IDE0 : WDC WD5000BEVT-22ZAT0 Use < > or < > to select

2. IDE2 : a device, then press
3. IDE1 : MATSHITADVD-RAM UJ880AS <F5> to move it down the
3. USB FDD : list, or <F6> to move
4. Network Boot : Atheros Boot Agent it up the list. Press
5. USB HDD : <Esc> to escape the menu
6. USB CDROM :

Chapter 2 37
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Item Specific Help

Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults Exit System Setup and
Discard Changes save your changes to
Save Changes CMOS.

The table below describes the parameters in this screen.

Parameter Description
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Exit utility without saving setup data to CMOS.
Changes
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
38 Chapter 2
BIOS Flash Utilities
The BIOS flash memory update is required for the following conditions:
• New versions of system programs
• New features or options
• Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1. Prepare a bootable diskette.
2. Copy the flash utilities to the bootable diskette.
3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2 39
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1. Press F2 during boot to enter the Setup Menu.
2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.

Item Specific Help

Boot priority order:
1. IDE0 : WDC WD5000BEVT-22ZAT0 Use < > or < > to select

2. IDE2 : a device, then press
3. IDE1 : MATSHITADVD-RAM UJ880AS <F5> to move it down the
3. USB FDD : list, or <F6> to move
4. Network Boot : Atheros Boot Agent it up the list. Press
5. USB HDD : <Esc> to escape the menu
6. USB CDROM :

3. Execute the FLASH.BAT batch file to update BIOS.

The flash process begins as shown.
40 Chapter 2
4. In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.
Chapter 2 41
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
1. Double-click the WinFlash executable.
2. Click OK to begin the update. A progress screen displays.
42 Chapter 2
Remove HDD/BIOS Password Utilities
This section provides you with details about removing HDD/BIOS password:
Remove HDD Password:
If you key in the wrong HDD password three times, an error is generated.
To reset the HDD password, perform the following steps:

1. After the error is displayed, select the Enter Unlock Password option on the screen.
2. An Encode key is generated for unlocking utilities. Note down this key.
3. Execute the UnlockHD.EXE file to create the unlock code in DOS Mode using the format UnlockHD
[Encode code] with the code noted in the previous step, as follows:
UnlockHD 76943488
4. The command generates a password which can be used for unlocking the HDD.
Password: 46548274
5. Key in the password from the previous step to unlock the HDD as shown.
Chapter 2 43
Removing BIOS Passwords:
To clear the User or Supervisor passwords, open the RAM door and use a metal instrument to short the
RTC_RST and ME _RST jumper.
Cleaning BIOS Passwords

To clean the User or Supervisor passwords, perform the following steps:
1. From a DOS prompt, execute clnpwd.exe
2. Press 1 or 2 to clean the desired password shown on the screen.
The onscreen message determines whether the function is successful or not.
44 Chapter 2
Using Boot Sequence Selector
The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot
Sequence Selector, perform the following steps:
1. Enter into DOS.
2. Execute BS.exe to display the usage screen.
3. Select the desired boot sequence by entering the corresponding sequence. For example, enter BS2 to
change the boot sequence to HDD | CD ROM | LAN | Floppy.
Chapter 2 45
Using DMITools
The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI
pool for hardware management.
When the BIOS displays Verifying DMI pool data it is checking that the table correlates with the hardware
before sending to the operating system (Windows, etc.).
To update the DMI Pool, perform the following steps:
1. Boot into DOS.
2. Execute dmitools. The following messages report to screen to confirm completion:
• dmitools /r ==> Read dmi string from bios
• dmitools /wm xxxx ==> Write manufacturer name to eeprom (max. 16 characters)
• dmitools /wp xxxx ==> Write product name to eeprom (max. 16 characters)
• dmitools /ws xxxx ==> Write serial number to eeprom (max. 22 characters)
• dmitools /wu xxxx ==> Write uuid to eeprom
• dmitools /wa xxxx ==> Write asset tag to eeprom (max. 32 characters)
The following examples show the commands and the corresponding output information.
Read DMI Information from Memory

Input:
dmitools /r
Output:
Manufacturer (Type1, Offset04h): Acer
Product Name (Type1, Offset05h): TravelMate xxxxx
Serial Number (Type1, Offset07h): 01234567890123456789
UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Asset Tag (Type3, Offset04h): Acet Asstag
Write Product Name to EEPROM

Input:
dmitools /wp Acer
Write Serial Number to EEPROM

Input:
dmitools /ws 01234567890123456789
4). Write UUID to EEPROM (Create UUID from Intel WFM20.pdf)

Input:
dmitools /wu
5). Write Asset Tag to EEPROM

Input:
dmitools /wa Acet Asstag
NOTE: When using any of the Write options, restart the system to make the new DMI data effective.
46 Chapter 2
Using the LAN Utility
Run the LAN utility in DOS mode by preforming the following steps:
1. Run the MAC.BAT file.
2. Run the NAYF0.BAT file.
3. The function is successful when “passed” displays onscreen.
Chapter 2 47
48 Chapter 2
Chapter 3
Machine Disassembly and Replacement

IMPORTANT:The outside housing and color may vary from the mass produced model.
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
• Wrist grounding strap and conductive mat for preventing electrostatic discharge
• Flat screwdriver
• Philips screwdriver
• Plastic flat screwdriver
• Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3 49
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.

4. Remove the battery pack.
Disassembly Process
IMPORTANT:The LCD Module cannot be disassembled outside of factory conditions. If any part of the LCD
Module is faulty, such as the camera, antenna or LCD panel, the whole module must be replaced.
The disassembly process is divided into the following stages:
• External module disassembly
• Main unit disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the mainboard, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List

Screw Quantity Part Number
M2.45D 8.0L K 5.5D 0.8T ZKNL 14 86.WBF02.001
M2.5D 5L K 5.5D ZK NL + CR3 23 86.WBF02.010
M2.46D 3.0L K 5.5D 0.8T ZKNL 3 86.WBF02.002
M1.98D 3.0L K 4.6D 0.8T ZKNL 20 86.WBF02.003
M3.0D 3.0L K 4.9D NI 8 86.WBF02.005
M2D 4.0L K 4.6D NI NL 2 86.WBF02.007
ASSY THML SPRING 4 86.WBF02.009
50 Chapter 3
External Module Disassembly Process
IMPORTANT:The outside housing and color may vary from the mass produced model.
External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the main
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Turn off system

and peripherals
power
Disconnect power
and signal cables
from system
Remove
Battery
Remove Remove
Dummy Cards Lower Covers
Remove Remove Remove Remove Remove

ODD DIMMs WLAN Primary HDD Secondary HDD
NOTE: Items enclosed with broken lines (— - - —) are optional and may not be present.
Screw List
Step Screw Quantity Part No.
WLAN Module M2*3 1 86.WBF02.003
ODD Module M2.5*5 1 86.WBF02.010
ODD Bracket M2*3 2 86.WBF02.003
Primary HDD Carrier M3*3 4 86.WBF02.005
Secondary HDD Carrier M3*3 4 86.WBF02.005
Chapter 3 51
Removing the Battery Pack
1. Turn computer over. Slide the battery lock in the direction shown.
2. Slide and hold the battery release latch to the release position (1), then lift out the battery pack from the main
unit (2).
52 Chapter 3
Removing the SD dummy card
1. Push the SD dummy card all the way in to eject it.
2. Pull the card out from the slot.
Chapter 3 53
Removing the Lower Covers
1. See “Removing the Battery Pack” on page 52.
2. Loosen the five captive screws in the memory and HDD covers.
HDD2, WLAN,
and Memory
Cover
HDD1
Cover
3. Remove the HDD1 Cover.
4. Remove the HDD2, WLAN, and Memory Cover as shown.
54 Chapter 3
Removing the Optical Drive Module
1. See “Removing the Lower Covers” on page 54.
2. Remove the screw securing the ODD module.
Step Size Quantity Screw Type

ODD Module M2.5*5 1
3. Insert a suitable tool into the access slot as shown. Gently lever the ODD module out of the chassis.
4. Pull the optical drive module out from the chassis.
Chapter 3 55
5. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive
module.

ODD Bracket M2*3 2
6. Remove the ODD bezel by rotating the top edge downward and pulling it clear of the module.
56 Chapter 3
Removing the DIMM Modules
2. Push out the release latches on both sides of the DIMM socket to release the DIMM module.
3. Remove the DIMM module.
4. Repeat steps for the second DIMM module if present.
Chapter 3 57
Removing the WLAN Module
2. Remove the adhesive tape securing the Antenna cables in place.
3. Disconnect the antenna cables from the WLAN Module.
NOTE: Cable placement is Black to the MAIN terminal (left) and White to the AUX terminal (right).
58 Chapter 3
4. Move the Antennas away and remove the two screws to release the WLAN Module.

WLAN Module M2*3 1
5. Detach the WLAN Module from the WLAN socket.
NOTE: When reattaching the antennas, ensure the cables are tucked into the chassis to prevent damage.
Chapter 3 59
Removing the Primary HDD Module
2. Using the pull-tab, slide the HDD Module in the direction of the arrow to disconnect the interface.
3. Lift the HDD Module clear of the HDD bay.

NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
4. Remove the four screws (two each side) securing the hard disk to the carrier.

HDD Carrier M3*3 4
60 Chapter 3
5. Remove the HDD from the carrier.
Chapter 3 61
Removing the Secondary HDD Module
NOTE: The Secondary HDD is optional and may not be present.
2. Using the pull-tab, slide the HDD Module in the direction of the arrow to disconnect the interface.
3. Lift the HDD Module clear of the HDD bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
62 Chapter 3
4. Remove the four screws (two each side) securing the hard disk to the carrier.

HDD Carrier M3*3 4
5. Remove the HDD from the carrier.
Chapter 3 63
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
Remove External
Modules before
proceeding
Remove
Switch Cover
Remove Remove
Keyboard Media Board
Remove
LCD Module
Remove
Upper Cover
Upper Lower
Cover Cover
Remove
Remove Remove Remove
TouchPad
Media Board FFC LED Board Speaker Module
Bracket

RTC Battery Modem Module USB Board
Remove
Mainboard
Remove Remove
RJ-11 Jack Thermal Module
Remove
CPU
Screw List
Switch Cover M2.5*5 3 86.WBF02.010
LCD Module M2.5*8 4 86.WBF02.001
M2.5*5 2 86.WBF02.010
Upper Cover M2.5*8 10 86.WBF02.001
M2.5*5 9 86.WBF02.010
M2.5*3 3 86.WBF02.002
TouchPad Bracket M2*3 1 86.WBF02.003
Speaker Module M2*3 4 86.WBF02.003
Modem Board M2*3 2 86.WBF02.003
USB Board M2.5*5 1 86.WBF02.010
Mainboard M2.5*5 1 86.WBF02.010
CPU Fan M2*3 3 86.WBF02.003
Thermal Module M2.5*6.5 4 86.WBF02.009
64 Chapter 3
Removing the Switch Cover
1. See “Removing the Battery Pack” on page 52.
2. Lift the Media Board FFC cover as shown to expose the FFC connector.
3. Open the FFC locking latch and disconnect the Media Board FFC.
4. Remove the three securing screws from the Lower Cover.

Switch Cover M2.5*5 3
Chapter 3 65
5. Open the computer lid to approximately 45° and push the Switch Cover from the underside of the computer to
release the locking latches securing the cover in place.
6. Turn the computer over and open the lid fully. Lift the left side of the Switch Cover as shown.
7. Working along the Switch Cover toward the right hinge, gently pry up the cover as shown.
66 Chapter 3
8. Rotate the Switch Cover toward the LCD panel and lift it away from the Upper Cover.
Chapter 3 67
Removing the Media Board
1. See “Removing the Switch Cover” on page 65.
2. Pry the Media Board away from the Switch Cover as shown.
NOTE: A very strong adhesive is used to secure the board in place.
3. Pry the board away from the Upper Cover and remove it completely.
68 Chapter 3
Removing the Keyboard
1. See “Removing the Switch Cover” on page 65.
2. Lift the keyboard from the centre as shown to release the securing clips on each side.
3. Turn the Keyboard over on the TouchPad to expose the FFC cable.
4. Open the locking latch on the FFC as shown.
Chapter 3 69
5. Disconnect the FFC cable from the mainboard.
6. Lift the keyboard clear of the chassis.
70 Chapter 3
Removing the LCD Module
1. See “Removing the Keyboard” on page 69.
2. Turn the computer over. Remove the two securing screws from the bottom of the chassis.

LCD Module M2.5*8 2
3. Open the computer lid and stand the chassis on its edge. Ensure the Antenna Cables are free from
obstructions as shown.
Chapter 3 71
4. Remove the adhesive tape securing the cables in place and pull the Antenna cables through the casing as
shown.
5. Remove the cables from the cable channel as shown. Ensure that the cables are completely free of the
retaining clips all the way to the hinge well.
72 Chapter 3
6. Disconnect the Power Board cable from the Mainboard.
7. Remove the cable from the cable channel as shown. Ensure that the cable is completely free of the retaining
clips all the way to the hinge well.
8. Disconnect the power cable from the Mainboard as shown. Ensure that the cable is completely free of the
Chapter 3 73
9. Disconnect the MIC cable from the Mainboard as shown. Ensure that the cable is completely free of the
10. Remove the four securing screws (two each side) from the LCD module.

LCD Module M2.5*8 2
(red callout)
LCD Module M2.5*5 2

(green callout)
74 Chapter 3
11. Carefully remove the LCD module from the chassis.
Chapter 3 75
Removing the Upper Cover
1. See “Removing the LCD Module” on page 71.
2. Turn the computer over. Remove the thirteen screws on the bottom panel.

Upper Cover M2.5*8 10
(red callout)

(green callout)

(blue callout)
76 Chapter 3
3. Turn the computer over. Remove the nine screws on the top panel.

(red callout)

(blue callout)
4. Remove the adhesive tape holding the cables in place.
Chapter 3 77
5. Disconnect the following cables from the Mainboard.
A
B
6. Disconnect A as shown. 7. Release the locking latch and remove B as shown.
8. Release the locking latch and remove C as shown. 9. Release the locking latch and remove D as shown.
NOTE: Avoid pulling on cables directly to prevent damage to the connectors. Use the pull-tabs on FFC cables
whenever available to prevent damage.
78 Chapter 3
10. Starting at the top-inside edges of the Upper Cover above the Battery Bay, lift the Upper Cover away from the
Lower Cover as shown.
11. Work along the top edge prying the casing apart as shown.
12. Pry apart the left and right sides of the casing and lift the Upper Cover away from the Lower Cover.
Chapter 3 79
Removing the TouchPad Bracket
1. See “Removing the Upper Cover” on page 76.
2. Release the FFC locking latch and disconnect the TouchPad FFC from the cover.
3. Remove the single screw securing the TouchPad Bracket to the Upper Cover.

TouchPad Bracket M2*3 1
4. Hold down the left side of the bracket as shown. Lift and pivot the right edge in the direction of the arrow to
release the locking latches on the front edge.
5. Remove the bracket from the Upper Cover.
80 Chapter 3
Removing the Media Board FFC
2. Lift the Media Board FFC as shown to release the adhesive securing it to the Upper Cover.
3. Pull the FFC through the Upper Cover as shown. Ensure that the cable passes through the casing completely.
4. Lift the FFC to remove it from the Upper Cover.
Chapter 3 81
Removing the LED Board
2. Lift the right edge of the LED Board to release the adhesive securing the board to the Upper Cover.
3. Lift the LED Board away from the Upper Cover as shown.
4. Remove the LED Board from the chassis and slide the FFC through the casing as shown.
82 Chapter 3
Removing the Speaker Module
2. Remove the four screws from the speaker modules.

Speaker Module M2*3 4
3. Remove the right side Speaker cable from the channel as shown.
4. Lift the mylar sheet away from the Upper Cover to expose the Speaker cable. Remove the cable from the
Upper Cover.
Chapter 3 83
5. Lift the entire Speaker assembly clear of the Upper Cover.
84 Chapter 3
Removing the RTC Battery
IMPORTANT:Follow local regulations for disposal of all batteries.
2. The RTC Battery is soldered to the Mainboard. To replace the battery, solder the new battery to the
connections shown.
Chapter 3 85
Removing the Modem Board
2. Remove the two securing screws from the Modem Board.

Modem Board M2*3 2
3. Remove the adhesive tape securing the Modem cable to the Mainboard.
86 Chapter 3
4. Lift the Modem Board away from the Mainboard, taking care not to damage the cable attached to the underside
of the board.
5. Disconnect the cable from the underside of the Modem Board and lift the board clear of the chassis.
Chapter 3 87
Removing the USB Board
2. Disconnect the USB Board cable from the Mainboard connector.
3. Lift the USB cable away from Lower Cover to detach the adhesive.
4. Remove the single screw securing the USB Board to the Lower Cover.

USB Board M2.5*5 1
88 Chapter 3
5. Lift the USB Board out of the Lower Cover as shown.
6. Remove the USB Board cable from the board connector.
Chapter 3 89
Removing the Mainboard
1. See “Removing the Modem Board” on page 86.
2. See “Removing the USB Board” on page 88.
3. Remove the single screw securing the Mainboard to the Lower Cover.

Mainboard M2.5*5 1
4. Lift the Mainboard from the Lower Cover right side first, and place it on a clean, dust-free surface.
90 Chapter 3
Removing the RJ-11 Jack
1. See “Removing the Mainboard” on page 90.
2. Remove the adhesive tape securing the RJ-11 cable to the Lower Cover.
3. Remove the RJ-11 cable from the cable channel. Ensure that the cable is free from all cable clips.
4. Lift the cable bundle away from the Lower Cover to detach the adhesive securing it in place.
Chapter 3 91
5. Lift the RJ-11 Jack away from the Lower Cover to detach the adhesive securing it in place.
92 Chapter 3
Removing the CPU Fan
2. Disconnect the CPU Fan power cable from the Mainboard.
3. Remove the three securing screws from the CPU Fan.

CPU Fan M2*3 3
4. Remove the CPU Fan from the Mainboard.
Chapter 3 93
Removing the Thermal Module
2. Remove the four screws securing the Thermal Module to the Mainboard in reverse numerical order from 4 to 1.
3 1
2 4

Thermal Module M2.5*6.5 4
3. Using both hands, lift the Thermal Module clear of the Mainboard.
94 Chapter 3
Removing the CPU
1. See “Removing the Thermal Module” on page 94.
2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° counter-clockwise as shown.
3. Lift the CPU clear of the socket as shown.
Chapter 3 95
LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Remove LCD
Panel from Main
Unit before
proceeding
Remove
LCD Bezel

Power Board LCD Panel Camera Module
Remove Remove Remove Remove

LCD FPC Cable LCD Brackets Antennas Microphone
Screw List
LCD Bezel M2.5*5 4 86.WBF02.010
M2*4 2 86.WBF02.007
LCD Panel M2.5*5 2 86.WBF02.010
Power Board M2*3 1 86.WBF02.003
LCD Brackets M2*3 6 86.WBF02.003
96 Chapter 3
Removing the LCD Bezel
1. See “Removing the LCD Module” on page 71.
2. Remove the four screw caps and six screws (four on the Bezel and two on the Hinge Covers).

LCD Bezel M2.5*5 4
(red callout)
LCD Bezel M2*4 2

(green callout)
3. Starting from the top centre of the bezel, pry the bezel upwards and away from the panel. Move along the top
edge and down each side until all sides of the bezel are removed.
NOTE: If necessary, use a pry to lift up the outside edges of the bezel.
Chapter 3 97
Removing the Camera Module
1. See “Removing the LCD Bezel” on page 97.
2. Disconnect the camera cable.
3. Remove the Camera from the module.
98 Chapter 3
Removing the LCD Panel
1. See “Removing the Camera Module” on page 98.
2. Remove the two securing screws from the LCD Panel.

LCD Panel M2.5*5 2
3. Lift the LCD Panel out of the module, rear edge first, as shown.
The LCD Module appears as follows when the LCD Panel is removed.
Chapter 3 99
Removing the Power Board
1. See “Removing the LCD Panel” on page 99.
2. Remove the single screw securing the Power Board Bracket to the LCD Module.

Power Board M2*3 1
3. Lift the Power Board Bracket from the LCD Panel as shown.
4. Remove the Power Board from the bracket as shown.
100 Chapter 3
Removing the LCD Brackets and FPC Cable
2. Turn the LCD panel over to expose the rear. Lift the cable as shown to disengage the adhesive strip securing it
in place.
3. Remove the adhesive tape and lift the adhesive protector securing the cable to the LCD Panel.
4. Disconnect the cable from the panel connector and lift the FPC cable from the panel.
Chapter 3 101
5. Remove the six securing screws (three on each side) from the LCD Panel brackets.

LCD Brackets M2*3 6
6. Remove the LCD Brackets by pulling away from the LCD Panel.
102 Chapter 3
Removing the Microphone Module
2. Remove the strips holding the microphone cable in place. Ensure the cable is free from obstructions.
3. Lift the Microphone Module clear of the module.
Chapter 3 103
Removing the Antennas
2. Starting from the right hinge, remove the white Antenna cable from the cable channel running along the bottom
edge of the LCD Module.
3. Remove the adhesive strips holding the left Antenna cable in place. Ensure the cable is free from obstructions.
104 Chapter 3
4. Remove the adhesive tape (green callout) and lift the left side Antenna from the LCD module as shown.
5. Remove the adhesive strips holding the right Antenna cable in place. Ensure the cable is free from
obstructions.
6. Remove the adhesive tape (green callout) and lift the right side Antenna from the LCD module as shown.
Chapter 3 105
LCD Module Reassembly Procedure
Replacing the Antennas, Power Board, and MIC
1. Replace the left and right antennas as shown. Ensure that the locating pin on each antenna is correctly
seated. Press down on the adhesive pads (green callout) to secure the antennas in place.
Locating Pin Locating Pin
2. Replace the left antenna cable (white) as shown. Ensure that the cable is inserted along the cable channel
and secured under each adhesive tab strip.
106 Chapter 3
3. Replace the right antenna cable (black) as shown. 4. Place the Power Board in to the bracket as shown.
Ensure that the cable is secured under each
adhesive tab strip.
5. Place the Power Board Bracket in the LCD Module 6. Replace the single screw to secure the bracket in
as shown. place.
7. Place the Microphone Module in the LCD Module, 8. Run the cable as shown and secure it using the
as shown, and press down to secure it in place. adhesive tabs.
Chapter 3 107
NOTE: The LCD Module appears as shown when the Antennas, Power Board, and MIC are replaced
correctly.
108 Chapter 3
Replacing the LCD Panel
1. Align the LCD brackets with the screw holes on the panel.
2. Starting with the top most screws (marked with ), replace the six screws in the brackets as shown.
3. Insert the LCD Panel cable into the LCD Panel 4. Replace the adhesive strip securing the connector
connector as shown. in place.
5. Replace the adhesive strip as shown.
Chapter 3 109
6. Replace the LCD cable as shown an press down along the cable’s length to secure the cable to the panel.
IMPORTANT:Ensure the cable is placed between the green callouts to avoid trapping when the panel is
replaced.
7. Place the LCD Panel in the back cover, bottom edge first, and lower it in to place as indicated.
IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped under the panel.
110 Chapter 3
8. Replace the two screws to secure the panel in the LCD Module.
Replacing the Camera Module

1. Align the Camera Board with the locating pins and 2. Connect the cable to the Camera Board.
place the camera in the LCD Module.
Chapter 3 111
Replacing the LCD Bezel
1. Locate the bezel bottom edge first and press down until there are no gaps between the bezel and the LCD
Module.
IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel.
112 Chapter 3
2. Press down around the entire perimeter of the bezel until there are no gaps between the bezel and the LCD
Module.
3. Replace the six screws as indicated.

NOTE: The Bezel securing screws differ in size: Red callout—M2.5*5, Green callout—M2*4.
Chapter 3 113
Main Module Reassembly Procedure
Replacing the CPU
IMPORTANT: The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU socket.
1. Place the CPU into the CPU socket as shown, taking note of the Pin1 locator.
Socket CPU
Pin1 Locator Pin1 Locator
2. Using a flat-bladed screw driver, rotate the CPU locking screw 180° clockwise to secure the CPU in place.
Replacing the Thermal Module

IMPORTANT:Apply a suitable thermal grease and ensure all heat pads are in place before replacing the
Thermal Module.
The following thermal grease types are approved for use:
• Silmore GP50
• Honeywell PCM45F-SP
• ShinEtsu 7762
The following thermal pads are approved for use:
Eapus XR-PE
1. Remove all traces of thermal grease from the CPU using a lint-free cloth or cotton swab and Isopropyl
Alcohol, Acetone, or other approved cleaning agent.
2. Apply a small amount of thermal grease to the centre of the CPU—there is no need to spread the grease
manually, the force used during the installation of the Thermal Module is sufficient.
114 Chapter 3
3. Align the four screw holes on the Thermal Module 4. Secure the four screws (in numerical order from
and Mainboard and lower the module into place. screw 1 to screw 4) in the Thermal Module as
Keep the module as level as possible to spread the shown.
thermal grease evenly.
3 1
2 4
Replacing the CPU Fan

1. Align the three screw holes on the CPU Fan and 2. Secure the three screws in the CPU Fan as shown.
Mainboard and lower the module into place.
3. Connect the CPU Fan power cable to the Mainboard connector as shown.
Chapter 3 115
Replacing the RJ-11 Jack
1. Place the RJ-11 Jack in the Lower Cover as 2. Replace the cable bundle and press down to
shown. secure the adhesive in place
3. Run the cable along the Lower Cover as shown, 4. Secure the cable in place with an adhesive strip.
using all available cable clips.
116 Chapter 3
Replacing the Mainboard
1. Ensure that the Mainboard is face up (the CPU is not visible). Place the Mainboard in the chassis, left side
first (1), then rotate it downward into position (2).
2. Ensure that the RJ-11 (Modem) cable is accessible when the Mainboard is replaced as shown.
(1)
(2)
3. Replace the single securing screw in the mainboard.
Chapter 3 117
Replacing the USB Board
1. Reconnect the USB Board cable to the USB 2. Align the locating holes and pins on the Lower
Board. Cover and replace the USB Board.
3. Replace the single screw securing the board to the 4. Replace the cable in the cable channel as shown
Lower Cover. and press down to secure it in place.
5. Reconnect the USB cable to the USB Board.
118 Chapter 3
Replacing the Modem Board
1. Reconnect the RJ-11 cable to the Modem Board. 2. Align the screw holes on the Modem and Lower
Cover and replace the board.
3. Secure the cable in place with adhesive tape. 4. Press down as indicated to connect the board-to-
board interface.
5. Secure the Modem Board to the Mainboard with two screws.
Chapter 3 119
Replacing the Speaker Module
1. Place the left Speaker Module in the chassis as 2. Lift the mylar sheet away from the Upper Cover and
shown, ensuring that the locating pins are seated run the Speaker cable along the Upper Cover using
correctly. all available cable clips.
3. Continue running the cable along the Upper Cover 4. Place the right Speaker Module in the chassis as
using all available cable clips. shown, ensuring that the locating pins are seated
correctly.
5. Replace the four securing screws.

NOTE: Ensure that the Speaker cable runs as shown in the image below to avoid trapping when the Upper
Cover is replaced.
120 Chapter 3
Replacing the LED Board
1. Pass the LED Board FFC through the Upper Cover 2. Place the LED Board in the Upper Cover and press
as shown. down as indicated to secure the board in place.
Replacing the Media Board FFC

1. Place the Media Board FFC on the Upper Cover as 2. Pass the upper end of the cable through the Upper
shown, and press down to secure the adhesive in Cover as shown.
place.
Chapter 3 121
Replacing the TouchPad Bracket
1. Replace the TouchPad Bracket bottom edge first to 2. Secure the bracket to the Upper Cover with a single
engage the securing clips (1). Rotate the bracket screw.
on to the Upper Cover and press down as
indicated (2).
(2)
(1)
3. Insert the TouchPad FFC in to the connector as 4. Close the FFC locking latch to secure the cable in
shown. place.
Replacing the Upper Cover

1. Place the upper cover on the lower cover front edge first and lower the cover into position.
122 Chapter 3
2. Press down around the front and sides to secure the Upper Cover in place.
NOTE: Ensure that there a no gaps between the Upper and Lower Covers.
3. Reconnect the following cables as shown.
A
B
Chapter 3 123
4. Connect A as shown. 5. Insert B as shown and close the locking latch.
6. Insert C as shown and close the locking latch. 7. Insert D as shown and close the locking latch.
8. Secure cables A and B in place using adhesive tape.
124 Chapter 3
9. Replace the nine screws in the upper cover as shown.
NOTE: The securing screws differ in size: Red callout—M2.5*5, Blue callout—M2.5*3.
10. Turn the computer over and replace the thirteen screws as shown.
NOTE: The securing screws differ in size: Red callout—M2.5*8, Green callout—M2.5*5, Blue callout—M2.5*3.
Chapter 3 125
Replacing the LCD Module
1. Turn the computer over. Align the LCD hinges with the lower cover and replace the LCD module.
2. Replace the four securing screws (two each side), starting with the left side hinge. Ensure that the LCD
cables are not trapped in the hinges.
NOTE: The securing screws differ in size: Red callout—M2.5*8, Green callout—M2.5*5.
3. Run the MIC cable along the cable channel as 4. Reconnect the MIC cable to the Mainboard as
shown, using all the available cable clips. shown.
126 Chapter 3
5. Run the LVDS cable along the cable channel as 6. Reconnect the LVDS cable to the Mainboard as
shown, using all the available cable clips. shown.
7. Run the Power Board cable along the cable channel 8. Connect the Power Board cable to the Mainboard
using all available cable clips. as shown.
9. Run the Antenna cables along the cable channel 10. Insert the Antenna cables through the chassis as
using all available cable clips. shown.
Chapter 3 127
11. Pull the Antennas completely through from the under side of the computer.
12. Secure the cables in place with adhesive tape.
13. Replace the two securing screws.
128 Chapter 3
Replacing the Keyboard
1. Place the Keyboard face down on the TouchPad 2. Close the FFC locking latch to secure the cable in
area.Reconnect the FFC as shown. place.
3. Turn the keyboard over and insert it front edge first 4. Press down as indicated to seat the Keyboard.
into the chassis.
NOTE: Ensure that the six locating tabs are correctly seated.
Chapter 3 129
Replacing the Media Board
1. Align the Media Board with the transparent pane 2. Press the Media Board down to secure it in place
on the Switch Cover. with adhesive.
130 Chapter 3
Replacing the Switch Cover
1. Place the Switch Cover rear edge first on to the Upper Cover. Rotate the Switch Cover downward on the
Keyboard.
2. Press down the edges of the cover to snap it into place, then press the centre down until it snaps in to place.
3. Turn the computer over and replace the three securing screws as shown.
Chapter 3 131
4. Lift the Media Board FFC cover as shown to 5. Connect the FFC to the Media Board as shown.
expose the FFC connector.
6. Close the FFC locking latch to secure the FFC in 7. Replace the Media Board FFC cover.
place.
132 Chapter 3
Replacing the Hard Disk Drive Modules
1. Place the HDD in the HDD carrier. 2. Replace the four screws (two each side) to secure
the carrier.
3. Insert the Secondary HDD, right side first, and 4. Slide the Secondary HDD to the right to connect
lower it into place. the interface.
5. Insert the Primary HDD, right side first, and lower it into place. Slide the Primary HDD to the right to connect
the interface.
Chapter 3 133
Replacing the WLAN Module
1. Insert the WLAN Module into the WLAN socket. 2. Replace the single screw to secure the module.
3. Connect the two antenna cables to the module. 4. After connecting the cables to the terminals,
secure the cables in place using adhesive tape.
NOTE: Cable placement is Black to the MAIN terminal (left) and White to the AUX terminal (right).
Replacing the DIMM Modules

1. Insert the DIMM Module in place. 2. Press down to lock the DIMM module in place.
134 Chapter 3
Replacing the ODD Module
1. Press the bezel into the tray, bottom edge first, to 2. Secure the ODD bracket with the two screws.
secure it to the ODD Module.
3. Push the ODD Module into the ODD bay until it is 4. Replace the single screw to secure the Module.
flush with the casing.
Replacing the Lower Covers

1. Replace the HDD2, WLAN, and Memory Cover back edge first as shown.
Chapter 3 135
2. Replace the HDD1 Cover as shown.
IMPORTANT:Press down around the perimeter of the covers to ensure that the all the securing tabs are
correctly located in the casing.
3. Secure the five captive screws to hold the covers in place.
HDD2, WLAN,
and Memory
Cover
HDD1
Cover
136 Chapter 3
Replacing the SD Dummy Card
1. Insert the SD Dummy Card into the slot and push until the card clicks into place and is flush with the casing.
Replacing the Battery

1. Slide and hold the battery release latch to the 2. Slide the battery lock in the direction shown to
release position (1), insert the battery pack and secure the battery in place.
press down (2).
Chapter 3 137
138 Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Go To
Power On Issue Page 140
No Display Issue Page 141
Random Loss of BIOS Settings Page 142
LCD Failure Page 143
Internal Keyboard Failure Page 143
TouchPad Failure Page 144
Internal Speaker Failure Page 145
Internal Microphone Failure Page 147
HDD Failure Page 148
ODD Failure Page 149
USB (Right side) Failure Page 153
WLAN Failure Page 154
Bluetooth Failure Page 155
Easy Button Failure Page 156
Thermal Unit Failure Page 157
External Mouse Failure Page 157
Other Functions Failure Page 158
Motherboard CMOS discharge Page 159
Intermittent Failures Page 159
Undermined Failures Page 159
4. If the Issue is still not resolved, see “Online Support Information” on page 207.
Chapter 4 139
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace non-defective FRUs:
Start
OK
Swap
Check AC/Battery
Check
AC/Batt only NG
AC/Batt only
power on
power on
OK OK
Check
Check
Power/B Swap Power
Power/BOK NG SW/B
Whether
Whether OK
Swap M/B
Computer Shuts down Intermittently

If the system powers off at intervals, perform the following actions one at a time to correct the problem.
1. Check the power cable is properly connected to the computer and the electrical outlet.
2. Remove any extension cables between the computer and the outlet.
3. Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4. Disconnect the power and open the casing to check the Thermal Unit (see “Thermal Unit Failure” on page
157) and fan airways are free of obstructions.
5. Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
6. Remove any recently installed software.
140 Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
START
Re pla ce CPU No CPU OK?

goto no p ower
Power On ? No trouble sho oting
step
Rep la ce L CD m odule Ext. DDRRAM

No Conn ec t
LC D pane l/ OK ? module well No
connected? it well
LC D cab le
Replac e
VGA BD Ext. DDRRAM
Con nec t it we ll module OK?
No E xt. DDR RAM
No OK ? m odule
o r Replac e VGA
Or Conn ect it w ell?
BD
Rep la ce C PU we ll
M /B No Conn ect it well
con nec te d?
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1. Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2. Make sure the computer has power by checking at least one of the following occurs:
• Fans start up
• Status LEDs light up
If there is no power, see “Power On Issue” on page 140.
3. Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4. Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 143.
5. Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6. Reseat the memory modules.
7. Remove the drives (see “Disassembly Process” on page 50).
Chapter 4 141
Abnormal Video Display
If video displays abnormally, perform the following actions one at a time to correct the problem.
1. Reboot the computer.
2. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 50.
3. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 50.
4. Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 50.
5. Check the display resolution is correctly configured:
a. Minimize or close all Windows.
b. If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c. If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d. Click and drag the Resolution slider to the desired resolution.
e. Click Apply and check the display. Readjust if necessary.
6. Roll back the video driver to the previous version if updated.
7. Remove and reinstall the video driver.
8. Check the Device Manager to determine that:
• The device is properly installed. There are no red Xs or yellow exclamation marks.
• There are no device conflicts.
• No hardware is listed under Other Devices.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
Random Loss of BIOS Settings

If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1. If the computer is more than one year old, replace the CMOS battery.
2. Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3. If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
4. If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5. Replace the Motherboard.
142 Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace non-
defective FRUs:
Start
OK
Check LCD Swap LCD panel/

NG
Module LCD cable
ok
Swap M/B
Built-In Keyboard Failure

If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
START
Keyboard FPC Connect

No
well connected? it well
Replace
Keyboard OK? No
keyboard
Replace M/B
Chapter 4 143
TouchPad Failure
If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not
Start
OK
Re-assemble
Check M/B the T/P FFC to
NG M/B
T/P FFC
OK OK
Swap/
Check Reassemble
Logic Upper NG the T/P board
or T/P FFC
Swap M/B
144 Chapter 4
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
Start
OK
Re-assemble
Check M/B
NG the speaker cable
Speaker cable
to M/B
ok
OK
Check
NG Swap speaker
speaker
Swap M/B
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1. Reboot the computer.
2. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
• The device is properly installed.
• There are no red Xs or yellow exclamation marks.
3. Roll back the audio driver to the previous version, if updated recently.
4. Remove and reinstall the audio driver.
5. Ensure that all volume controls are set mid range:
a. Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b. Click Mixer to verify that other audio applications are set to 50 and not muted.
6. Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7. Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
Chapter 4 145
8. Remove and recently installed hardware or software.
9. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
146 Chapter 4
Internal Microphone Failure
If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not
Start
OK
Re-assemble
Check M/B the MIC cable
NG to M/B
Mic cable
OK OK
Check MIC Swap MIC wire

wire of LCD NG of LCD module
module
Swap M/B
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1. Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2. Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3. The microphone appears on the Recording tab.
4. Right-click on the microphone and select Enable.
5. Select the microphone then click Properties. Select the Levels tab.
6. Increase the volume to the maximum setting and click OK.
7. Test the microphone hardware:
a. Select the microphone and click Configure.
b. Select Set up microphone.
c. Select the microphone type from the list and click Next.
d. Follow the onscreen prompts to complete the test.
Chapter 4 147
HDD Not Operating Correctly
If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1. Disconnect all external devices.
2. Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3. Run the Windows 7 Startup Repair Utility:
a. insert the Windows 7 Operating System DVD in the ODD and restart the computer.
b. When prompted, press any key to start to the operating system DVD.
c. The Install Windows screen displays. Click Next.
d. Select Repair your computer.
e. The System Recovery Options screen displays. Click Next.
f. Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g. Select Startup Repair.
h. Startup Repair attempts to locate and resolve issues with the computer.
i. When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4. Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5. Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6. Ensure all cables and jumpers on the HDD and ODD are set correctly.
7. Remove any recently added hardware and associated software.
8. Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9. Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
11. Replace the HDD. See “Disassembly Process” on page 50.
148 Chapter 4
ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace non-
defective FRUs:
S TA R T
DV D /
C D -R OM d rive r No Insta ll it
installe d?
DV D /
C D- R OM m o dule No S e at it w e ll
w ell sea te d?
DV D / R e plac e
C D -R O M d isc No D VD /C D- R OM
OK ? d isc
DV D / R e plac e
C D- R OM m o dule No D VD /C D- R OM
OK ? m o dule
R e plac e M /B
ODD Not Operating Correctly

If the ODD exhibits any of the following symptoms it may be faulty:
• Audio CDs do not play when loaded
• DVDs do not play when loaded
• Blank discs do not burn correctly
• DVD or CD play breaks up or jumps
• Optical drive not found or not active:
• Not shown in My Computer or the BIOS setup
Chapter 4 149
• LED does not flash when the computer starts up
• The tray does not eject
• Access failure screen displays
• The ODD is noisy
Perform the following general solutions one at a time to correct the problem.
1. Reboot the computer and retry the operation.
2. Try an alternate disc.
3. Navigate to Start´ Computer. Check that the ODD device is displayed in the Devices with Removable
Storage panel.
4. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
a. Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device
and click Enable.
b. Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and
click Enable.
c. Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If
a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
d. Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a
device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.
e. If the exclamation marker is not removed from the item in the lists, try removing any recently installed
software and retrying the operation.
Discs Do Not Play
If discs do not play when inserted in the drive, perform the following actions one at a time to correct the
problem.
1. Check that the disc is correctly seated in the drive tray and that the label on the disc is visible.
2. Check that the media is clean and scratch free.
3. Try an alternate disc in the drive.
4. Ensure that AutoPlay is enabled:
a. Navigate to Start´ Control Panel´ Hardware and Sound´ AutoPlay.
b. Select Use AutoPlay for all media and devices.
c. In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.
5. Check that the Regional Code is correct for the selected media:
IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero,
the region cannot be changed even Windows is reinstalled or the drive is moved to another computer.
a. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b. Double-click DVD/CD-ROM drives.
c. Right-click DVD drive and click Properties, then click the DVD Region tab.
d. Select the region suitable for the media inserted in the drive.
Discs Do Not Burn Properly

If discs can not be burned, perform the following actions one at a time to correct the problem.
1. Ensure that the default drive is record enabled:
a. Navigate to Start´ Computer and right-click the writable ODD icon. Click Properties.
b. Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the
drop down list.
150 Chapter 4
c. Click OK.
2. Ensure that the software used for burning discs is the factory default. If using different software, refer to
the software's user manual.
Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem.
1. Check that system resources are not running low:
a. Try closing some applications.
b. Reboot and try the operation again.
2. Check that the ODD controller transfer mode is set to DMA:
a. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager.
b. Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0.
c. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is
checked and click OK.
d. Repeat for the other ATA Devices shown if applicable.
Drive Not Detected

If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.
1. Restart the computer and press F2 to enter the BIOS Utility.
2. Check that the drive is detected in the ATAPI Model Name field on the Information page.
NOTE: Check that the entry is identical to one of the ODDs specified in “Hardware Specifications and
Configurations” on page 17.
3. Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 50.
a. Check for broken connectors on the drive, motherboard, and cables.
b. Check for bent or broken pins on the drive, motherboard, and cable connections.
c. Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4. Reseat the drive ensuring and all cables are connected correctly.
5. Replace the ODD. See “Disassembly Process” on page 50.
Drive Read Failure

If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the
problem.
1. Remove and clean the failed disc.
2. Retry reading the CD or DVD.
d. Test the drive using other discs.
e. Play a DVD movie
f. Listen to a music CD
If the ODD works properly with alternate discs, the original disc is probably defective and should be
replaced.
3. Turn off the power and remove the cover to inspect the connections to the ODD. See “Disassembly
Process” on page 50.
a. Check for broken connectors on the drive, motherboard, and cables.
b. Check for bent or broken pins on the drive, motherboard, and cable connections.
Chapter 4 151
c. Try an alternate cable, if available. If the drive works with the new cable, the original cable should be
replaced.
4. Replace the ODD. See “Disassembly Process” on page 50.
152 Chapter 4
USB (Right Side) Failure
If the right-side USB fails, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
Start
OK
Re-assemble
Check the USB/B
NG cable to M/B
USB/B to
M/B cable
OK OK
Check Swap USB/B

USB/B NG Module
module
Swap M/B
Chapter 4 153
Wireless Function Failure
If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace non-
defective FRUs:
Start
OK
Re-assemble the
Check antenna to
NG
antenna to WL /
WL /WiMax card WiMax card
ok OK
Check antenna NG Swap the antenna
ok OK
Check WL/ Swap WL/WiMax

NG
WiMax card card
ok OK
Check
function /B NG Swap function/B
Swap M/B
154 Chapter 4
Bluetooth Function Test Failure
If the Bluetooth function test fails, perform the following actions one at a time to correct the problem. Do not
Start
OK
Check BT cable
NG
Re-assemble BT
well connect Cable
ok OK
Check BT cable NG Swap BT cable
ok OK
Check BT NG Swap BT
ok OK
Check
NG Swap Function/B
Function/B
Swap M/B
Chapter 4 155
Easy Button Failure
If the Easy Button fails, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
Start
OK
Check Re-assemble
NG the function/B
function/B
to M/B FFC FFC to M/B
OK OK
Check Swap The

function/B NG function/B
and FFC
Swap M/B
156 Chapter 4
Thermal Unit Failure
If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
START
Fan power
wire well No Connect it well
connected?
Replace thermal
Fan OK? No
module
CPU
heatsink well No Seat it well
seated?
Replace
CPU OK? No
CPU
Replace M/B
External Mouse Failure

If an external Mouse fails, perform the following actions one at a time to correct the problem.
1. Try an alternative mouse.
2. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See
the mouse user manual.
3. If the mouse uses a USB connection, try an alternate USB port.
4. Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure.
Chapter 4 157
5. Restart the computer.
6. Remove any recently added hardware and associated software.
7. Remove any recently added software and reboot.
9. Run the Event Viewer to check the events log for errors. For more information see Windows Help and
Support.
10. Roll back the mouse driver to the previous version if updated recently.
11. Remove and reinstall the mouse driver.
12. Check the Device Manager to determine that:
• The device is properly installed. There are no red Xs or yellow exclamation marks.
Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or
Volume Wheel fail, perform the following general steps to correct the problem. Do not replace non-defective
FRUs:
1. Check Drive whether is OK.
2. Check Test Fixture is ok.
3. Swap M/B to Try.
158 Chapter 4
Motherboard CMOS Discharge
If any problems such as incorrect CMOS settings, the CMOS data can be cleared by short-circuiting the
CMOS CLRP2 jumpers. Open the memory bay door and short-circuit the jumpers near the DDR socket, using
a metal conductivity tool.
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 140.):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
• Non-Acer devices
• Printer, mouse, and other external devices
• Battery pack
• Hard disk drive
• DIMM
• CD-ROM/Diskette drive Module
• PC Cards
Chapter 4 159
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
• System board
• LCD assembly
160 Chapter 4
Post Codes
These tables describe the POST codes and descriptions during the POST.
Chipset POST Codes

The following table details the chipset POST codes and functions used in the POST.
Sec:
NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc)
Code Description
0xC2 MTRR setup
0xC3 Enable cache
0xC4 Establish cache tags
0xC5 Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0.
0xCF Cache Init Finished
Memory:
DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC)
Code Description
0xA0 First memory check point
0x01 Enable MCHBAR
0x02 Check for DRAM initialization interrupt and reset fail
0x03 Verify all DIMMs are DDR or DDR2 and unbuffered
0x04 Detect an improper warm reset and handle
0x05 Detect if ECC SO-DIMMs are present in the system
0x06 Verify all DIMMs are single or double sided and not asymmetric
0x07 Verify all DIMMs are x8 or x16 width
0x08 Find a common CAS latency between the DIMMS and the MCH
0x09 Determine the memory frequency and CAS latency to program
0x10 Determine the smallest common TRAS for all DIMMs
0x11 Determine the smallest common TRP for all DIMMs
0x12 Determine the smallest common TRCD for all DIMMs
0x13 Determine the smallest refresh period for all DIMMs
0x14 Verify burst length of 8 is supported by all DIMMs
0x15 Determine the smallest tWR supported by all DIMMs
0x16 Determine DIMM size parameters
0x17 Program the correct system memory frequency
0x18 Determine and set the mode of operation for the memory channels
0x19 Program clock crossing registers
0x20 Disable Fast Dispatch
0x21 Program the DRAM Row Attributes and DRAM Row Boundary registers
0x22 Program the DRAM Bank Architecture register
0x23 Program the DRAM Timing & and DRAM Control registers
Chapter 4 161
Code Description
0x24 Program ODT
0x25 Perform steps required before memory init
0x26 Program the receive enable reference timing control register
Program the DLL Timing Control Registers, RCOMP settings
0x27 Enable DRAM Channel I/O Buffers
0x28 Enable all clocks on populated rows
0x29 Perform JEDEC memory initialization for all memory rows
0x30 Perform steps required after memory init
0x31 Program DRAM throttling and throttling event registers
0x32 Setup DRAM control register for normal operation and enable
0x33 Enable RCOMP
0x34 Clear DRAM initialization bit in the SB
0x35 Initialization Sequence Completed, program graphic clocks
0x43 Program Thermal Throttling
BDS & Specific action:

Code Description
0x00 Report the legacy boot is happening
0x12 Wake up the Aps
0x13 Initialize SMM Private Data and relocate BSP SMBASE
0x21 PC init begin at the stage1
0x27 Report every memory range do the hard ware ECC init
0x28 Report status code of every memory range
0x50 Get the root bridge handle
0x51 Notify pci bus driver starts to program the resource
0x58 Reset the host controller
0x5A IdeBus begin initialization
0x79 Report that the remote terminal is being disabled
0x7A Report that the remote terminal is being enabled
0x90 Keyboard reset
0x91 USB Keyboard disable
0x92 Keyboard detection
0x93 Report that the usb keyboard is being enabled
0x94 Clear the keyboard buffer
0x95 Init Keyboard
0x98 Mouse reset
0x99 Mouse disable
0x9A Detect PS2 mouse
0x9B Report that the mouse is being enabled
0xB8 Peripheral removable media reset (ex: IsaFloppy, USB device)
0xB9 Peripheral removable media disable
0xBB Peripheral removable media enable
0xE4 Report Status Code here for DXE_ENTRY_POINT once it is available
162 Chapter 4
Code Description
0xF8 Report that ExitBootServices () has been called
0xF9 Runtime driver set virtual address map
Chapter 4 163
Each PEIM entry point used in 80_PORT
Code Description
0x00
0x01 PEI_EVENT_LOG
0xA1 PEI_OEM_SERVICE
0xA2 PEI_SIO_INIT
0xA3 PEI_MONO_STATUS_CODE
0xA4 PEI_CPU_IO_PCI_CFG
0x06 PEI_CPU_IO
0x07 PEI_PCI_CFG
0xA5 PEI_CPU_PEIM
0xA6 PEI_PLATFORM_STAGE1
0xA7 PEI_VARIABLE
0xA8 PEI_SB_INIT
0x0C PEI_CAPSULE
0xAA PEI_PLATFORM_STAGE2
0xAC PEI_SB_SMBUS_ARP_DISABLED
0x0F PEI_HOST_TO_SYSTEM
0x40 PEI_MEMORY_INIT
0x41 PEI_S3_RESUME
0xAD PEI_CLOCK_GEN
0xAB PEI_OP_PRESENCE
0xAE PEI_FIND_FV
0x16 PEI_H2O_DEBUG_IO
0x17 PEI_H2O_DEBUG_COMM
0x16~0x1F PEI_RESERVED
0x20~0x2E PEI_OEM_DEFINED
0xAF PEI_DXE_IPL
Each Driver entry point used in 80_PORT

Code Description
0x30 RESERVED
0xB6 DXE_CRC32_SECTION_EXTRACT
0xB8 SCRIPT_SAVE
0xB9 ACPI_S3_SAVE
0xBA SMART_TIMER
0xBB JPEG_DECODER
0xBC PCX_DECODER
0xBE HT_CPU / MP_CPU
0xBF LEGACY_METRONOME
0xC0 FTWLITE
0xC1 RUN_RIME
0xC2 MONOTONIC_COUNTER
0xC3 WATCH_DOG_TIMER
164 Chapter 4
Code Description
0xC4 SECURITY_STUB
0xC5 DXE_CPU_IO
0xC6 CF9_RESET
0xC7 PC_RTC
0xC8 STATUS_CODE
0xC9 VARIABLE
EMU_VARIABLE
0xD9 DXE_CHIPSET_INIT
0x45 DXE_ALERT_FORMAT
0xD6 PCI_HOST_BRIDGE
0xD7 PCI_EXPRESS
0xD5 DXE_SB_INIT
0xDA IDE_CONTROLLER
0xDB SATA_CONTROLLER
0xDD SB_SM_BUS
0xE7 ISA_ACPI_DRIVER
0xE8 ISA_BUS
0xE9 ISA_SERIAL
0xED BUS_PCI_UNDI
0xEC PCI_BUS
0xF6 BOOT_PRIORITY
0xF7 FVB_SERVICE
0xF8 ACPI_PLATFORM
0xFB PCI_HOT_PLUG
0xFC DXE_PLATFORM
0xFD PLATFORM_IDE
0x97 SMBIOS
0x98 MEMORY_SUB_CLASS
0x99 MISC_SUB_CLASS
0x82 CON_PLATFORM
0x83 SAVE_MEMORY_CONFIG
0x84 ACPI_SUPPORT
0x85 CON_SPLITTER_UGA_VGA / CON_SPLITTER
0x88 VGA_CLASS
0x89 DATA_HUB
0x60 DISK_IO
0x8B MEMORY_TEST
0x62 CRISIS_RECOVERY
0x8D LEGACY_8259
0x8E LEGACY_REGION
0x8F LEGACY_INTERRUPT
0x70 BIOS_KEYBOARD
0x71 BIOS_VEDIO
Chapter 4 165
Code Description
0x72 MONITER_KEY
0x73 LEGACY_BIOS
0x75 LEGACY_BIOS_PLATFORM
0x76 PCI_PLATFORM
0x6C ISA_FLOOPY
0x6D PS2_MOUSE
0x6E USB_BOT
0x6F USB_CBI0
0x74 USB_MOUSE
0xFA SETUP_UTILITY
0x90 FW_BLOCK_SERVICE
0x78 SMM_USB_LEGACY
0x86 GRAPHICS_CONSOLE
0x87 TERMINAL
0x8A DATA_HUB_STD_ERR
0x7C FAT
0x7D PARTITION
0x7E ENGLISH
0x7F FRENCH
0x9E HII_DATABASE
0x9F OEM_SETUP_BROWSER
0x8C OEM_BADGING_SUPPORT
0xF9 SETUP_MOUSE
0x72 MONITOR_KEY
0xBD PLATFORM_BDS
0x8D RESERVED
0x8E RESERVED
0x8F RESERVED
0xA0 DXE_H2O_DEBUG_IO
0xB3 DXE_TPM_TCG
0xB4 DXE_TPM_PHYSICAL_PRESENCE
0xB7 DXE_OEM_SERVICE
0x9B DXE_ SECURITY_HDD_PASSWORD_SERVICE
0xA9 DXE_LAN_IDER_CONTROLLER
0x9C DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE
0x9D DXE_ SECURITY_ PASSWORD_CONSOLE
0xCB DXE_ DATA_HUB_RECORD_POLICY
0xB5 DXE_TPM_DRIVER
0x11 CHINESE
0xB0 JAPANESE
0xB1 DXE_UNICODE_COLLACTION
166 Chapter 4
Each SmmDriver entry point used in 80_PORT
Code Description
0xD4 SMM_ACCESS
0xDE SMM_CONTROL
0xCC SMM_BASE
0xD2 SMM_RUNTIME
0xDF SB_SMM_DISPATCH
0xD0 SMM_THUNK
0xCA SMM_ACPI_SW_CHILD
0xFE SMM_PLATFORM
0xD8 SMM_GMCH_MBI
0x90 SMM_FW_BLOCK_SERVICE
0x91 SMM_VARIABLE
0x92 SMM_IHISI
0x93 SMM_INT15_MICROCODE
0x94 SMM_PNP
0x95 SMM_INIT_PPM
0xD3 SMM_OEM_SERVICE
Chapter 4 167
168 Chapter 4
Chapter 5
Jumper and Connector Locations

Top View
Item Description
JLVDS1 LCD Connector
JP1 Internal MIC
JP3 Power board Connector
JKB1 Internal Keyboard Connector
JMDC1 Internal MDC Connector
JUSB2 USB Board connector
JBT1 B/T connector
JP7 Cap sensor board CONN
JTP1 T/P Connector
JREAD1 Card Reader Socket
JP5 Speaker CONN
JP4 LED Board CONN
Chapter 5 169
Bottom View
Item Description
PJP2 Battery Connector
JMINI1 WLAN Connector
JODD1 ODD Connector
JHDD1 HDD Connector
JDIMMI/2 RAM Connector
JCPU1 CPU Socket
JHDD2 2nd HDD Connector
JFAN1 FAN Connector
JUSB1 USB Connector
JHP1 Head-Phone Jack
JMIC1 MIC-In Jack
JUSB4 USB Connector
JHDMI1 HDMI Connector
JCRT1 CRT Connector
JRJ45 RJ45 Connector
JRJ45 RJ45 Connector
PJP1 AC-IN Jack
170 Chapter 5
LS-5022P USB Board
Item Description
JUSB1/JUSB2 USB Connector
JP1 USB Board CONN
LS-5024P Cap Sensor Board
Item Description
LED1 Power saving
LED2 Backup key
LED3 WLAN
LED4 TP Luck
LED5 Mute
LED6 VOL DOWN
LED7 VOL UP
LS-5026P LED Board
Item Description
LED1 B/T LED
Chapter 5 171
Item Description
LED2 Num LED
LED3 Cap LED
LED4 Media LED
LS-5027P SW Board
Item Description
SW1 Power S/W
172 Chapter 5
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for
Packard Bell EasyNote LJ75/LJ77. Packard Bell EasyNote LJ75/LJ77 provides one Hardware Open Gap on
main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
Clearing Password Check

Hardware Open Gap Description is as follows:
Item Mark Description Location

R588 RTC_RST Clear CMOS Jumper Memory bay (near DDR socket)
R589 ME_RST
Steps for Clearing BIOS Password Check

If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
1. Power Off the system, and remove HDD, AC and Battery from the machine.
2. Open the back cover of the machine.
3. Disconnect the RTC Battery cable and locate the G1 jumper.
Chapter 5 173
4. Use an electric conductivity tool to short the two points of the HW Gap.
5. Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the system till
BIOS POST finish. Then remove the tool from the HW Gap.
6. Restart system. Press F2 key to enter BIOS Setup menu.
7. If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and try
again.
NOTE: These steps are only for clearing BIOS Password (Supervisor Password and User Password).
174 Chapter 5
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:

BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:

The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery by USB flash crisis disk:

Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk
program in another system with Windows XP OS.
Follow the steps below:
1. Plug in the USB disk.
2. Launch the wincris.exe program to create a USB Crisis Disk. Click Start to initiate the process.
3. Select the Quick Format option to format the disk and click Start. Follow the instructions on the screen to
create the disk.
4. Copy the KAYF0X64.fd BIOS file into USB flash disk root directory.
NOTE: Do not place any other *.fd file in the USB flash disk root directory.
To use the Crisis USB key, do the following:
1. Plug USB storage into USB port.
2. Press Fn + ESC button then plug in AC power.
The Power button flashes orange once.
3. Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS.
4. Update the latest version BIOS for this machine by regular BIOS flashing process.
Chapter 5 175
176 Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Packard Bell EasyNote LJ75/
LJ77. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 177
Packard Bell EasyNote LJ75/LJ77 Exploded Diagrams
Main Assembly
No. Description Acer P/N

1 LCD Assy 6M.BGB02.003
2 Middle Cover 60.WBV02.001
3 Keyboard KB.I170G.111
4 Upper Cover 60.BE202.002
5 Mainboard MB.WHH02.001
6 Lower Assy 60.WBF02.003
178 Chapter 6
Base Assembly
1 3
No. Description Acer P/N

1 Touchpad Bracket 33.WBF02.002
2 Speaker 23.WBF02.002
3 Touchpad FCC 50.WBF02.002
4 Upper Cover 60.BE202.002
Chapter 6 179
LCD Assembly
3 7
4
6
9
10
No. Description Acer P/N No. Description Acer P/N

1 LCD Bezel 60.WBF02.008 6 Antenna (L) 50.WBF02.007
2 LCD Panel LK.17305.001 7 Bracket (R) 33.WBF02.004
3 LVDS Cable 50.WBF02.008 8 Antenna (R) 50.WBF02.006
4 Bracket (L) 33.WBF02.004 9 Microphone Set 23.WBF02.001
5 Camera 57.WBF02.001 10 LCD Cover 60.B5602.001
180 Chapter 6
Packard Bell EasyNote LJ75/LJ77 FRU List
CATEGORY Description Part No.
ADAPTER
Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH AP.06501.026
DB A, LV5 LED LF
Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA- AP.06503.024
1650-22AC LV5 LED LF
Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP- AP.0650A.012
A0652R3B 1LF, LV5 LED LF
Adapter DELTA 90W 19V 1.7x5.5x11 Blue ADP-90CD AP.09001.027
DB A, LV5 LED LF
Adapter LITE-ON 90W 19V 1.7x5.5x11 Blue PA-1900- AP.09003.021
34AR, LV5 LED LF
BATTERY
Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell BT.00603.042
4400mAh Main COMMON Normal Type
Battery SONY AS-2007B Li-Ion 3S2P SONY 6 cell BT.00604.025
Battery PANASONIC AS-2007B Li-Ion 3S2P BT.00605.021
PANASONIC 6 cell 4400mAh Main COMMON PSS
Battery SIMPLO AS-2007B Li-Ion 3S2P SAMSUNG 6 BT.00606.001
cell 4400mAh Main COMMON SDI 2.2F
Battery SIMPLO AS-2007B Li-Ion 3S2P PANASONIC 6 BT.00607.016
cell 4400mAh Main COMMON PSS
Battery SANYO AS-2007B Li-Ion 4S2P SANYO 8 cell BT.00803.024
4800mAh Main COMMON
Battery SONY AS-2007B Li-Ion 4S2P SONY 8 cell BT.00804.020
4800mAh Main COMMON
Battery SIMPLO AS-2007B Li-Ion 4S2P PANASONIC 8 BT.00807.015
BOARD
Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/ BH.21100.004
w:861
Lite-On Conexant -Unizion 1.5_3.3v AUS RD02-D330 FX.22500.021
MEDIA BOARD 55.BGB02.001
LED BOARD W/FFC 55.BGB02.002
USB BOARD 55.BGB02.003
POWER BOARD W/CABLE 55.BGB02.004
Chapter 6 181
Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) NI.23600.046
Liteon Wireless LAN Atheris HB93 1x2 BGN (HM) NI.23600.051
WN6602AH
Liteon Wireless LAN Realtek 8192SE BGN NI.23600.055
WN6603LH(2x2)
Lan Intel WLAN 112BN.HMWG MM#903341 KI.CPH01.001
CABLE
BLUE TOOTH CABLE 50.WBF02.001
T/P FFC 50.WBF02.002
MEDIA BOARD FFC 50.WBF02.003
USB CABLE 50.WBF02.004
RJ11 CABLE 50.WBF02.005
POWER CORD US 3 PIN 27.TAVV5.001

POWER CORD EU 3 PIN 27.TAVV5.002
POWER CORD AUS 3 PIN 27.TAVV5.003
POWER CORD UK 3 PIN 27.TAVV5.004
POWER CORD CHINA 3 PIN 27.TAVV5.005
POWER CORD SWISS 3 PIN 27.TAVV5.006
POWER CORD ITALIAN 3 PIN 27.TAVV5.007
POWER CORD DENMARK 3 PIN 27.TAVV5.008
POWER CORD JP 3 PIN 27.TAVV5.009
POWER CORD SOUTH AFRICA 3 PIN 27.TAVV5.010
POWER CORD KOERA 3 PIN 27.TAVV5.011
POWER CORD ISRAEL 3 PIN 27.TAVV5.012
POWER CORD INDIA 3 PIN 27.TAVV5.013
POWER CORD TWN 3 PIN 27.TAVV5.014
POWER CORD ARGENTINA 3 PIN 27.APV02.001
CASE/COVER/BRACKET ASSEMBLY
UPPER CASE ASSY-PB For WIN7, INCL. TP/TP 60.BE202.002
MYLAR
LOWER CASE DIS W/RJ11 F 60.WBF02.003

LOWER CASE DIS W/O RJ11 F 60.WBF02.004
LOWER CASE UMA W/RJ11 F 60.WBJ02.001
LOWER CASE UMA W/O RJ11 F 60.WBJ02.002
182 Chapter 6
MIDDLE COVER - For WIN 7 60.WBV02.001
POWER BOARD BRACKET 33.WBF02.005
TP BRACKET 33.WBF02.002
MAIN HDD DOOR W/ RUBBER FOOT 42.WBF02.001
HDD CARRIER 33.WBF02.001
HDD DOOR FOR NB W/ 2 HDD 42.WBF02.002
CPU/PROCESSOR
CPU Intel Core i3 330M PGA 2.13G 35W Arrandale, KC.33001.DMP
TJ90, VT, 3M L3
CPU Intel Core i5 430M PGA 2.26G ARD, up to SC KC.43001.DMP
2.53G, 3M L3
CPU Intel Core i5 520M 2.4G 3M KC.52001.DMP
CPU Intel Core i5 540M 2.53G 3M KC.54001.DMP
HDD/HARD DISK DRIVER
HDD SEAGATE 2.5" 5400rpm 160GB ST9160314AS KH.16001.042
Wyatt SATA LF F/W:0001SDM1
HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 KH.16007.024
Panther B SATA LF F/W:C60F
HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX KH.16004.006
Libra SATA LF F/W: FG011J
HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO KH.16008.022
ML160 SATA LF F/W:11.01A11
Panther B SATA LF F/W:C60F Disk imbalance criteria =
0.014g-cm
Libra SATA LF F/W:FG001J
Chapter 6 183
HDD WD 2.5" 5400rpm 250GB WD2500BEVT-22ZCT0 KH.25008.021
Panther B SATA LF F/W: C60F
HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 KH.32008.013
HDD WD 2.5" 5400rpm 500GB WD5000BEVT-22ZAT0 KH.50008.013
MEMORY
Memory SAMSUNG SO-DIMM DDRIII 1066 1GB KN.1GB0B.028
M471B2873EH1-CF8 LF 64*16 0.055um
Memory MICRON SO-DIMM DDRIII 1066 1GB KN.1GB04.015
MT8JSF12864HZ-1G1F1 LF 128*8 0.065um
Memory NANYA SO-DIMM DDRIII 1066 1GB KN.1GB03.031
NT1GC64BH8A1PS-BE LF 64*16 0.07um
Memory ELPIDA SO-DIMM DDRIII 1066 1GB KN.1GB09.012
EBJ10UE8BDS0-AE-F LF 128*8 0.065um
Memory HYNIX SO-DIMM DDRIII 1066 1GB KN.1GB0G.025
HMT112S6BFR6C-G7 N0 LF 64*16 0.055um
Memory SAMSUNG SO-DIMM DDRIII 1066 2GB KN.2GB0B.012
M471B5673EH1-CF8 LF 128*8 0.055um
Memory ELPIDA SO-DIMM DDRIII 1066 2GB KN.2GB09.006
Memory HYNIX SO-DIMM DDRIII 1066 2GB KN.2GB0G.014
HMT125S6BFR8C-G7 N0 LF 128*8 0.055um
KEYBOARD
Keyboard GATEWAY GP-7T Black SJV70 Internal 17 KB.I170G.111
Standard 103KS Black US International
Standard 103KS Black Greek
Standard 103KS Black Arabic
Standard 103KS Black Russian
Standard 103KS Black Thailand
Standard 103KS Black UK
Standard 103KS Black German
184 Chapter 6
Standard 103KS Black Swiss/G
Standard 103KS Black CZ/SK
Standard 103KS Black Belgium
Standard 103KS Black Danish
Standard 103KS Black Italian
Standard 103KS Black French
Standard 103KS Black Hungarian
Standard 103KS Black Norwegian
Standard 103KS Black Portuguese
Standard 103KS Black Spanish
Standard 103KS Black Turkish
Standard 103KS Black Sweden
Standard 103KS Black SLO/CRO
Standard 103KS Black Nordic
Standard 103KS Black Japanese
DVD-RW DRIVE
ODD SUPER-MULTI DRIVE MODULE 6M.BGB02.001
ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL KU.00801.035
8X TS-L633C LF W/O bezel SATA (HF + Windows 7)
ODD PANASONIC Super-Multi DRIVE 12.7mm Tray KU.00807.070
DL 8X UJ890A LF W/O bezel SATA (HF + Windows 7)
ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X KU.0080D.048
GT30N LF W/O bezel SATA (HF + Windows 7)
ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X KU.0080E.027
AD-7585H LF W/O bezel SATA (HF + Windows 7)
ODD BEZEL-SUPER MULTI 42.WBF02.004
ODD BRACKET 33.WBF02.003
Chapter 6 185
BD COMBO MODULE
ODD BD COMBO MODULE 6M.BGB02.002
ODD PLDS BD COMBO 12.7mm Tray DL 4X DS-4E1S KO.0040F.003
LF W/O bezel SATA (Windows 7)
ODD BEZEL-BD COMBO 42.WBF02.005
ODD BRACKET 33.WBF02.003
LCD
ASSY LEC LCD MODULE 17.3" WXGA GLARE W/ 6M.BGB02.003
ANTENNA *2, CAMERA, IMR, BLACK - PB
ASSY LEC LCD MODULE 17.3" WXGA GLARE W/ 6M.BGC02.001
ANTENNA *2, CAMERA, IMR, RED - PB
ASSY LEC LCD MODULE 17.3" WXGA GLARE W/ 6M.BH302.001
ANTENNA *3, CAMERA, IMR, BLACK - PB
ANTENNA *3, CAMERA, IMR, RED - PB
ASSY LEC LCD MODULE 17.3" WXGA GLARE W/ 6M.BGB02.004
ANTENNA *2, IMR, W/O CCD, BLACK - PB
ASSY LEC LCD MODULE 17.3" WXGA GLARE W/ 6M.BGC02.002
ANTENNA *2, IMR, W/O CCD, RED - PB
ANTENNA *3, IMR, W/O CCD, BLACK - PB
ANTENNA *3, IMR, W/O CCD, RED - PB
LED LCD AUO 17.3" WXGA+ Glare B173RW01-V0 LF LK.17305.001
220nit 8ms 600:1
LED LCD SAMSUNG 17.3" WXGA+ Glare LK.17306.001
LTN173KT01-A01 LF 220nit 8ms 600:1
LED LCD LPL 17.3" WXGA+ Glare LP173WD1-TLA1 LK.17308.001
LF 220nit 8ms 600:1
LED LCD CMO 17.3" WXGA+ Glare N173O6-L02 LF LK.1730D.001
220nit 8ms 600:1
LED LCD AUO 17.3" WXGA+ Glare B173RW01-V3 LF LK.17305.002
220nit 8ms 500:1
LCD COVER IMR-PB BLACK 60.B5602.001
LCD COVER IMR-PB RED 60.BE202.001
LCD COVER IMR-PB BLACK 60.B5602.001
ANTENNA MAIN (R -1X2) 50.WBF02.006
186 Chapter 6
ANTENNA AUX (L) 50.WBF02.007
LCD BEZEL 60.WBF02.008
LVDS CABLE 50.WBF02.008
LCD BRACKET R+L 33.WBF02.004
CAMERA 0.3M 57.WBF02.001
MAINBOARD
Mainboard NV79/ENLJ75/ENLJ77 UMA Intel HM55 LF MB.WHH02.001
Mainboard NV79/ENLJ75/ENLJ77 Park XT 512MB MB.WHH02.003
VRAM Intel HM55 LF
Mainboard NV79/ENLJ75/ENLJ77 Madison Pro 1GB MB.WHH02.002
VRAM Intel HM55 LF
HEATSINK
VGA THERMAL MODULE-PARK 60.BH302.001
VGA THERMAL MODULE-MADISON 60.BG902.001
CPU THERMAL MODULE 60.BGB02.001
FAN-UMA 23.BGB02.001
SPEAKER
MIC SET 23.WBF02.001
SPEAKER 23.WBF02.002
MISCELLANEOUS
BATTERY MYLAR 42.WBF02.003
RUBBER FOOT 47.WBF02.002
NAME PLATE-ENLJ77 40.BGC02.001
Chapter 6 187
NAME PLATE-ENLJ75 40.BH302.001
LCD SCREW RUBBER 47.WBF02.001
PVC MYLAR FOR LCD COVER-LEFT 47.WBU02.001
Screw List
SCREW
SCREW M2.45D 8.0L K 5.5D 0.8T ZKNL 86.WBF02.001
SCREW M2.5D 5L K 5.5D ZK NL + CR3 86.WBF02.010
SCREW M2.5D 4.15L K 5.5D ZK NL CR3 86.WBF02.004
SCREW M3.0D 3.0L K 4.9D NI 86.WBF02.005
SCREW M2.5D 3.2L K 6D NI 86.WBF02.006
SCREW M2D 4.0L K 4.6D NI NL 86.WBF02.007
SCREW M2.0D 3L K 5D NI 86.WBF02.008
SCREW ASSY THML SPRING 86.WBF02.009
188 Chapter 6
Chapter 6 189
Appendix A
Model Definition and Configuration
Packard Bell EasyNote LJ75 Series

Model Acer Part No RO Country Description
ENLJ75- LX.BG902.005 EMEA Spain ENLJ75-334G64Mn W7HP64BTES1
334G64Mn MADISON_PRO1GBCkk_V3 2*2G/640/6L2.2/
5R/CB_GN_0.3D_GEk_ESA2
EASYNOTE_LJ75-JN-332SP
434G50Mn MADISON_PRO1GBCkk_V3 2*2G/500_L/
6L2.2/5R/CB_GN_0.3D_GEk_ESA2
EASYNOTE_LJ75-JO-431SP
ENLJ75- LX.BG902.014 EMEA Germany ENLJ75-436G50Bn W7HP64BTDE1
436G50Bn MADISON_PRO1GBCkk_V3 2G+4G/500_L/
6L2.2/5R/CB_bgn_0.3D_GEk_DE43
EASYNOTE_LJ75-JO-075GE
ENLJ75- LX.BG902.001 EMEA France ENLJ75-434G1TMn W7HP64BTFR1
434G1TMn MADISON_PRO1GBCkk_V3 2*2G/
500_L+500_L/6L2.2/5R/
CB_GN_0.3D_GEk_FR51 EASYNOTE_LJ75-
JO-230FR
ENLJ75- LX.BG902.008 EMEA France ENLJ75-434G1TBn W7HP64BTFR1
434G1TBn MADISON_PRO1GBCkk_V3 2*2G/
500_L+500_L/6L2.2/5R/
JO-257FR
ENLJ75- LX.BG902.013 EMEA Greece ENLJ75-436G64Mn W7HP64BTGR1
436G64Mn MADISON_PRO1GBCkk_V3 2G+4G/640/BT/
6L2.2/5R/CB_GN_0.3D_GEk_EL43
EASYNOTE_LJ75-JO-201GR
ENLJ75- LX.BG902.012 EMEA Greece ENLJ75-434G50Mn W7HP64BTGR1
434G50Mn MADISON_PRO1GBCkk_V3 2*2G/500_L/BT/
6L2.2/5R/CB_GN_0.3D_GEk_EL43
EASYNOTE_LJ75-JO-110GR
ENLJ75- S2.BG902.001 WW WW ENLJ75-544G50Mn W7HP64BWW2
544G50Mn MADISON_PRO1GBCkk_V3 2*2G/500_L/BT/
6L2.2/5R/CB_GN_0.3D_GEk_EN11
ENLJ75- LX.BG902.011 EMEA Nordic ENLJ75-434G64Mn W7HP64BTND1
5R/CB_GN_0.3D_GEk_ENU3
EASYNOTE_LJ75-JO-250NC
ENLJ75- LX.BG902.010 EMEA France ENLJ75-334G64Mn W7HP64BTFR1
5R/CB_GN_0.3D_GEk_FR51
EASYNOTE_LJ75-JN-255FR
ENLJ75- LX.BG902.002 EMEA Portugal ENLJ75-334G50Mn W7HP64BTPT1
6L2.2/5R/CB_GN_0.3D_GEk_PT43
EASYNOTE_LJ75-JN-332PT
Appendix A 190
ENLJ75- LX.BG902.009 EMEA Italy ENLJ75-434G32Mn W7HP64BTIT1
5R/CB_GN_0.3D_GEk_IT71
EASYNOTE_LJ75-JO-110IT
6L2.2/5R/CB_GN_0.3D_GEk_FR51
EASYNOTE_LJ75-JO-256FR
6L2.2/5R/CB_GN_0.3D_GEk_FR51
EASYNOTE_LJ75-JP-258FR
5R/CB_GN_0.3D_GEk_ESA2
EASYNOTE_LJ75-JO-432SP
ENLJ75- S2.BG902.002 WW WW ENLJ75-524G50Mi W7HP64BWW2
524G50Mi MADISON_PRO1GBCkk_V3 2*2G/500_L/BT/
8L2.4/5R/CB_abgn_0.3D_GEk_EN11
ENLJ75- LX.BH302.010 EMEA France ENLJ75-434G82Mn W7HP64BTFR1
434G82Mn PARK_XT512Ckk_V3 2*2G/500_L+320/6L2.2/
5R/CB_bgn_0.3D_GEk_FR51
EASYNOTE_LJ75-JO-264FR
ENLJ75- LX.BH302.005 EMEA Switzerland ENLJ75-338G50Mn W7HP64BTCH1
338G50Mn PARK_XT512Ckk_V3 2*4G/500_L/6L2.2/5R/
CB_bgn_0.3D_GEk_SW23
EASYNOTE_LJ75-JN-335CH
ENLJ75- LX.BH302.009 EMEA Italy ENLJ75-436G50Mn W7HP64BTIT1
436G50Mn PARK_XT512Ckk_V3 2G+4G/500_L/6L2.2/
5R/CB_bgn_0.3D_GEk_IT71
EASYNOTE_LJ75-JO-111IT
ENLJ75- LX.BH302.008 EMEA Spain ENLJ75-434G64Mn W7HP64BTES1
434G64Mn PARK_XT512Ckk_V3 2*2G/640/6L2.2/5R/
CB_bgn_0.3D_GEk_ESA2 EASYNOTE_LJ75-
JO-433SP
ENLJ75- LX.BH302.004 EMEA Switzerland ENLJ75-434G50Mn W7HP64BTCH1
CB_GN_0.3D_GEk_SW23 EASYNOTE_LJ75-
JO-545CH
ENLJ75- LX.BH302.007 EMEA Russia ENLJ75-333G32Mi W7HP64RUBTRU2
333G32Mi PARK_XT512Ckk_V3 1G+2G/320/BT/6L2.2/
5R/CB_bg_0.3D_GEk_RU41
EASYNOTE_LJ75-JN-101RU
ENLJ75- LX.BH302.006 EMEA Germany ENLJ75-434G32Bn W7HP64BTDE1
434G32Bn PARK_XT512Ckk_V3 2*2G/320/6L2.2/5R/
CB_bgn_0.3D_GEk_DE43 EASYNOTE_LJ75-
JO-076GE
ENLJ75- LX.BH302.003 EMEA UK ENLJ75-434G50Mn W7HP64BTGB1
CB_GN_0.3D_GEk_EN13 EASYNOTE_LJ75-
JO-080UK
191 Appendix A
ENLJ75- LX.BH302.002 EMEA France ENLJ75-334G50Mn W7HP64BTFR1
JN-253FR
ENLJ75- LX.BH302.001 EMEA Germany ENLJ75-434G32Mn W7HP64BTDE1
434G32Mn PARK_XT512Ckk_V3 2*2G/320/BT/6L2.2/5R/
CB_GN_0.3D_GEk_DE43 EASYNOTE_LJ75-
JO-070GE
ENLJ75- S2.BH302.001 WW WW ENLJ75-544G32Mi W7HP64BWW2
544G32Mi PARK_XT512Ckk_V3 2*2G/320/BT/6L2.2/5R/
CB_abgn_0.3D_GEk_EN11
ENLJ75- LX.BGB02.005 EMEA UK ENLJ75-334G32Mn W7HP64BTGB1 UMACkk
334G32Mn 2*2G/320/6L2.2/5R/CB_bgn_0.3D_GEk_EN13
EASYNOTE_LJ75-GN-020UK
ENLJ75- LX.BGB02.004 EMEA Germany ENLJ75-334G32Mn W7HP64BTDE1 UMACkk
334G32Mn 2*2G/320/6L2.2/5R/CB_GN_0.3D_GEk_DE43
EASYNOTE_LJ75-GN-071GE
ENLJ75- LX.BGB02.001 EMEA UK ENLJ75-334G50Mn W7HP64BTGB1 UMACkk
334G50Mn 2*2G/500_L/6L2.2/5R/
CB_GN_0.3D_GEk_EN13
ENLJ75- LX.BGB02.002 EMEA France ENLJ75-334G50Mn W7HP64BTFR1 UMACkk
334G50Mn 2*2G/500_L/6L2.2/5R/
GN-250FR
ENLJ75- LX.BGB02.003 EMEA Spain ENLJ75-334G32Mn W7HP64BTES1 UMACkk
334G32Mn 2*2G/320/6L2.2/5R/CB_GN_0.3D_GEk_ESA2
EASYNOTE_LJ75-GN-330SP
ENLJ75- S2.BGB02.001 WW WW ENLJ75-544G32Bi W7HP64BWW2 UMACkk
544G32Bi 2*2G/320/BT/6L2.2/5R/
Model Acer Part No CPU LCD VGA Chip VRAM 1

ENLJ75- LX.BG902.005 Ci3330M NLED17.3W MADISON_PRO 1G-DDR3 (64*16*8)
334G64Mn XGA+G
434G50Mn XGA+G
436G50Bn XGA+G
434G1TMn XGA+G
434G1TBn XGA+G
436G64Mn XGA+G
434G50Mn XGA+G
ENLJ75- S2.BG902.001 Ci5540M NLED17.3W MADISON_PRO 1G-DDR3 (64*16*8)
544G50Mn XGA+G
434G64Mn XGA+G
Appendix A 192
Model Acer Part No CPU LCD VGA Chip VRAM 1
334G64Mn XGA+G
334G50Mn XGA+G
434G32Mn XGA+G
434G50Mn XGA+G
624G50Mn XGA+G
434G64Mn XGA+G
ENLJ75- S2.BG902.002 Ci5520M NLED17.3W MADISON_PRO 1G-DDR3 (64*16*8)
524G50Mi XGA+G
ENLJ75- LX.BH302.010 Ci5430M NLED17.3W PARK_XT 512M-DDR3
434G82Mn XGA+G (64*16*4)
338G50Mn XGA+G (64*16*4)
436G50Mn XGA+G (64*16*4)
434G64Mn XGA+G (64*16*4)
434G50Mn XGA+G (64*16*4)
333G32Mi XGA+G (64*16*4)
434G32Bn XGA+G (64*16*4)
434G50Mn XGA+G (64*16*4)
334G50Mn XGA+G (64*16*4)
434G32Mn XGA+G (64*16*4)
ENLJ75- S2.BH302.001 Ci5540M NLED17.3W PARK_XT 512M-DDR3
544G32Mi XGA+G (64*16*4)
ENLJ75- LX.BGB02.005 Ci3330M NLED17.3W UMA N
334G32Mn XGA+G
334G32Mn XGA+G
334G50Mn XGA+G
334G50Mn XGA+G
334G32Mn XGA+G
ENLJ75- S2.BGB02.001 Ci5540M NLED17.3W UMA N
544G32Bi XGA+G
193 Appendix A
Memory Memory
Model Acer Part No Memory 1 Memory 2 HDD 1(GB)
3 4
ENLJ75- LX.BG902.005 SO2GBIII10 SO2GBIII10 N N N640GB5.4KS
334G64Mn
434G50Mn
436G50Bn
434G1TMn
434G1TBn
436G64Mn
434G50Mn
ENLJ75- S2.BG902.001 SO2GBIII10 SO2GBIII10 N N N500GB5.4KS
544G50Mn
434G64Mn
334G64Mn
334G50Mn
434G32Mn
434G50Mn
624G50Mn
434G64Mn
ENLJ75- S2.BG902.002 SO2GBIII10 SO2GBIII10 N N N500GB5.4KS
524G50Mi
ENLJ75- LX.BH302.010 SO2GBIII10 SO2GBIII10 N N N500GB5.4KS
434G82Mn
338G50Mn
436G50Mn
434G64Mn
434G50Mn
333G32Mi
434G32Bn
434G50Mn
Appendix A 194
Memory Memory
Model Acer Part No Memory 1 Memory 2 HDD 1(GB)
3 4
334G50Mn
434G32Mn
ENLJ75- S2.BH302.001 SO2GBIII10 SO2GBIII10 N N N320GB5.4KS
544G32Mi
ENLJ75- LX.BGB02.005 SO2GBIII10 SO2GBIII10 N N N320GB5.4KS
334G32Mn
334G32Mn
334G50Mn
334G50Mn
334G32Mn
ENLJ75- S2.BGB02.001 SO2GBIII10 SO2GBIII10 N N N320GB5.4KS
544G32Bi
Media Extra Card

Model Acer Part No HDD 2(GB) ODD
Processor SW1 Reader
ENLJ75- LX.BG902.005 N NSM8XS N NIS 5 in 1-
334G64Mn Build in
434G50Mn Build in
ENLJ75- LX.BG902.014 N NBDCB4XS N NIS 5 in 1-
436G50Bn Build in
ENLJ75- LX.BG902.001 N500GB5.4KS NSM8XS N NIS 5 in 1-
434G1TMn Build in
ENLJ75- LX.BG902.008 N500GB5.4KS NBDCB4XS N NIS 5 in 1-
434G1TBn Build in
436G64Mn Build in
434G50Mn Build in
ENLJ75- S2.BG902.001 N NSM8XS N NIS 5 in 1-
544G50Mn Build in
434G64Mn Build in
334G64Mn Build in
334G50Mn Build in
434G32Mn Build in
434G50Mn Build in
195 Appendix A
Media Extra Card
Model Acer Part No HDD 2(GB) ODD
Processor SW1 Reader
624G50Mn Build in
434G64Mn Build in
ENLJ75- S2.BG902.002 N NSM8XS N NIS 5 in 1-
524G50Mi Build in
ENLJ75- LX.BH302.010 N320GB5.4KS NSM8XS N NIS 5 in 1-
434G82Mn Build in
ENLJ75- LX.BH302.005 N NSM8XS N NIS 5 in 1-
338G50Mn Build in
436G50Mn Build in
434G64Mn Build in
434G50Mn Build in
333G32Mi Build in
ENLJ75- LX.BH302.006 N NBDCB4XS N NIS 5 in 1-
434G32Bn Build in
434G50Mn Build in
334G50Mn Build in
434G32Mn Build in
ENLJ75- S2.BH302.001 N NSM8XS N NIS 5 in 1-
544G32Mi Build in
ENLJ75- LX.BGB02.005 N NSM8XS N NIS 5 in 1-
334G32Mn Build in
334G32Mn Build in
334G50Mn Build in
334G50Mn Build in
334G32Mn Build in
ENLJ75- S2.BGB02.001 N NBDCB4XS N NIS 5 in 1-
544G32Bi Build in
Wireless VOIP Finger NB

Model Acer Part No Bluetooth
LAN1 Phone Print Chipset
ENLJ75- LX.BG902.005 3rd WiFi 2x2 N N N HM55
334G64Mn BGN
434G50Mn BGN
Appendix A 196
436G50Bn BGN
434G1TMn BGN
434G1TBn BGN
ENLJ75- LX.BG902.013 3rd WiFi 2x2 BT 2.1 N N HM55
436G64Mn BGN
ENLJ75- LX.BG902.012 3rd WiFi 2x2 BT 2.1 N N HM55
434G50Mn BGN
ENLJ75- S2.BG902.001 3rd WiFi 2x2 BT 2.1 N N HM55
544G50Mn BGN
434G64Mn BGN
334G64Mn BGN
334G50Mn BGN
434G32Mn BGN
434G50Mn BGN
624G50Mn BGN
434G64Mn BGN
ENLJ75- S2.BG902.002 INT6200H BT 2.1 N N HM55
524G50Mi
ENLJ75- LX.BH302.010 3rd WiFi 2x2 N N N HM55
434G82Mn BGN
338G50Mn BGN
436G50Mn BGN
434G64Mn BGN
434G50Mn BGN
ENLJ75- LX.BH302.007 3rd WiFi BG BT 2.1 N N HM55
333G32Mi
434G32Bn BGN
434G50Mn BGN
334G50Mn BGN
ENLJ75- LX.BH302.001 3rd WiFi 2x2 BT 2.1 N N HM55
434G32Mn BGN
197 Appendix A
ENLJ75- S2.BH302.001 INT6200H BT 2.1 N N HM55
544G32Mi
ENLJ75- LX.BGB02.005 3rd WiFi 2x2 N N N HM55
334G32Mn BGN
334G32Mn BGN
334G50Mn BGN
334G50Mn BGN
334G32Mn BGN
ENLJ75- S2.BGB02.001 INT6300H BT 2.1 N N HM55
544G32Bi
Appendix A 198
Packard Bell EasyNote LJ77 Series
ENLJ77- S2.BGA02.001 WW WW ENLJ77-543G50Mn W7HP64BWW2
543G50Mn MADISON_PRO1GBCrk_V3 2G+1G/500_L/BT/
6L2.2/5R/CB_GN_0.3D_GEr_EN11
ENLJ77- S2.BH402.001 WW WW ENLJ77-544G50Mi W7HP64BWW2
544G50Mi PARK_XT512Crk_V3 2*2G/500_L/BT/6L2.2/5R/
ENLJ77- S2.BGC02.00 WW WW ENLJ77-543G32Bn W7HP64BWW2 UMACrk
543G32Bn 1 2G+1G/320/BT/6L2.2/5R/
CB_GN_0.3D_GEr_EN11
ENLJ77- LX.BGC02.00 EMEA France ENLJ77-334G50Mn W7HP64BTFR1 UMACrk
334G50Mn 1 2*2G/500_L/6L2.2/5R/CB_GN_0.3D_GEr_FR51
EASYNOTE_LJ77-GN-251FR
Model Acer Part No CPU LCD VGA Chip VRAM 1 Memory 1

ENLJ77- S2.BGA02.001 Ci5540M NLED17.3 MADISON 1G-DDR3 SO2GBIII10
543G50Mn WXGA+G _PRO (64*16*8)
ENLJ77- S2.BH402.001 Ci5540M NLED17.3 PARK_XT 512M-DDR3 SO2GBIII10
544G50Mi WXGA+G (64*16*4)
ENLJ77- S2.BGC02.001 Ci5540M NLED17.3 UMA N SO2GBIII10
543G32Bn WXGA+G
ENLJ77- LX.BGC02.001 Ci3330M NLED17.3 UMA N SO2GBIII10
334G50Mn WXGA+G
Memory Memory HDD

Model Acer Part No Memory 2 HDD 1(GB)
3 4 2(GB)
ENLJ77- S2.BGA02.001 SO1GBIII10 N N N500GB5.4KS N
543G50Mn
ENLJ77- S2.BH402.001 SO2GBIII10 N N N500GB5.4KS N
544G50Mi
ENLJ77- S2.BGC02.001 SO1GBIII10 N N N320GB5.4KS N
543G32Bn
ENLJ77- LX.BGC02.001 SO2GBIII10 N N N500GB5.4KS N
334G50Mn
Media
Model Acer Part No ODD Extra SW1 Card Reader
Processor
ENLJ77-543G50Mn S2.BGA02.001 NSM8XS N NIS 5 in 1-Build in
ENLJ77-544G50Mi S2.BH402.001 NSM8XS N NIS 5 in 1-Build in
ENLJ77-543G32Bn S2.BGC02.001 NBDCB4XS N NIS 5 in 1-Build in
ENLJ77-334G50Mn LX.BGC02.001 NSM8XS N NIS 5 in 1-Build in
199 Appendix A
VOIP Finger
Model Acer Part No Wireless LAN1 Bluetooth NB Chipset
Phone Print
ENLJ77- S2.BGA02.001 3rd WiFi 2x2 BGN BT 2.1 N N HM55
543G50
Mn
ENLJ77- S2.BH402.001 INT6200H BT 2.1 N N HM55
544G50
Mi
ENLJ77- S2.BGC02.001 3rd WiFi 2x2 BGN BT 2.1 N N HM55
543G32B
n
ENLJ77- LX.BGC02.001 3rd WiFi 2x2 BGN N N N HM55
334G50
Mn
Appendix A 200
Appendix B
Test Compatible Components

This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® 7 environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Packard Bell EasyNote LJ75/
LJ77 Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B 201
Microsoft® Windows® 7 Environment Test
Vendor Type Description

2nd HDD
HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300
SEAGATE N250GB5.4KS HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS
TOSHIBA N250GB5.4KS HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX
WD N160GB5.4KS HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO
WD N320GB5.4KS HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0
WD N640GB5.4KS HDD WD 2.5" 5400rpm 640GB WD6400BEVT-
22A0RT0, ML320 SATA 8MB LF F/W:01.01A01
Adapter
HIPRO 65W Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-
A0652R3B 1LF, LV5 LED LF
LITE-ON 65W Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650-
22AC LV5 LED LF
LITE-ON 90W Adapter LITE-ON 90W 19V 1.7x5.5x11 Blue PA-1900-
34AR, LV5 LED LF
Audio Codec
Realtek ALC272X Realtek Audio Codec ALC272X
Battery
PANASONIC 6CELL2.2 Battery PANASONIC AS-2007B Li-Ion 3S2P
PANASONIC 6 cell 4400mAh Main COMMON PSS
SAMSUNG 6CELL2.2 Battery SAMSUNG AS-2007B Li-Ion 3S2P SAMSUNG 6
cell 4400mAh Main COMMON SDI 2.2F
SANYO 6CELL2.2 Battery SANYO AS-2007B Li-Ion 3S2P SANYO 6 cell
SANYO 8CELL2.4 Battery SANYO AS-2007B Li-Ion 4S2P SANYO 8 cell
4800mAh Main COMMON
SIMPLO 6CELL2.2 Battery SIMPLO AS-2007B Li-Ion 3S2P PANASONIC 6
SIMPLO 8CELL2.4 Battery SIMPLO AS-2007B Li-Ion 4S2P PANASONIC 8
SONY 6CELL2.2 Battery SONY AS-2007B Li-Ion 3S2P SONY 6 cell
202 Appendix B
SONY 8CELL2.4 Battery SONY AS-2007B Li-Ion 4S2P SONY 8 cell
4800mAh Main COMMON
Bluetooth
Foxconn BT 2.1 Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/
w:861
Camera
Chicony 0.3M DV Chicony 0.3M DV Calla_2G
Suyin 0.3M DV Suyin 0.3M DV Camellia_2G
Card Reader
5 in 1-Build in 5 in 1-Build in MS, MS Pro, SD, SC, XD
CPU
INTEL Ci3330M CPU Intel Core i3 330M PGA 2.13G 35W Arrandale,
TJ90, VT, 3M L3
INTEL Ci3350M CPU Intel Core i3 350M PGA 2.26G 35W Arrandale,
TJ90, VT, 3M L3
INTEL Ci5430M CPU Intel Core i5 430M PGA 2.26G ARD, up to SC
2.53G, 3M L3
INTEL Ci5520M CPU Intel Core i5 520M 2.4G 3M
INTEL Ci5540M CPU Intel Core i5 540M 2.53G 3M
INTEL Ci7620M CPU Intel Core i7 620M PGA 2.66G 4M
HDD
TOSHIBA N250GB5.4KS HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX
WD N160GB5.4KS HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO
WD N320GB5.4KS HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0
WD N640GB5.4KS HDD WD 2.5" 5400rpm 640GB WD6400BEVT-
22A0RT0, ML320 SATA 8MB LF F/W:01.01A01
LAN
Broadcom BCM57780 Broadcom BCM57780
LCD
AUO NLED17.3WXGA+G LED LCD AUO 17.3" WXGA+ Glare B173RW01-V0 LF
220nit 8ms 600:1
AUO NLED17.3WXGA+G LED LCD AUO 17.3" WXGA+ Glare B173RW01-V0 LF
220nit 8ms 600:1
Appendix B 203
CMO NLED17.3WXGA+G LED LCD CMO 17.3" WXGA+ Glare N173O6-L02 LF
220nit 8ms 600:1
LPL NLED17.3WXGA+G LED LCD LPL 17.3" WXGA+ Glare LP173WD1-TLA1
LF 220nit 8ms 600:1
SAMSUNG NLED17.3WXGA+G LED LCD SAMSUNG 17.3" WXGA+ Glare
LTN173KT01-A01 LF 220nit 8ms 600:1
MEM
A-DATA SO2GBIII10 Memory A-DATA SO-DIMM DDRIII 1066 2GB
HY7YG1B1674ZM LF 128*8 0.065um
ELPIDA SO1GBIII10 Memory ELPIDA SO-DIMM DDRIII 1066 1GB
ELPIDA SO2GBIII10 Memory ELPIDA SO-DIMM DDRIII 1066 2GB
HYNIX SO1GBIII10 Memory HYNIX SO-DIMM DDRIII 1066 1GB
HMT112S6BFR6C-G7 N0 LF 64*16 0.055um
HYNIX SO2GBIII10 Memory HYNIX SO-DIMM DDRIII 1066 2GB
HMT125S6BFR8C-G7 N0 LF 128*8 0.055um
MICRON SO1GBIII10 Memory MICRON SO-DIMM DDRIII 1066 1GB
MT8JSF12864HZ-1G1F1 LF 128*8 0.065um
MICRON SO2GBIII10 Memory MICRON SO-DIMM DDRIII 1066 2GB
MT16JSF25664HZ-1G1F1 LF 128*8 0.065um
NONE SO4GBIII10 Memory NONE SO-DIMM DDRIII 1066 4GB dummy P/
N LF
SAMSUNG SO1GBIII10 Memory SAMSUNG SO-DIMM DDRIII 1066 1GB
M471B2873EH1-CF8 LF 64*16 0.055um
SAMSUNG SO2GBIII10 Memory SAMSUNG SO-DIMM DDRIII 1066 2GB
M471B5673EH1-CF8 LF 128*8 0.055um
Modem
Lite-On Lite+Con MC4Z Lite-On Conexant -Unizion 1.5_3.3v AUS RD02-D330
1.5_3.3V Aus
NB Chipset
INTEL HM55 NB Chipset Intel CS BD82HM55
ODD
HLDS NBDCB4XS ODD HLDS BD COMBO 12.7mm Tray DL 4X CT21N LF
W/O bezel 1.00 SATA (HF + Windows 7)
HLDS NSM8XS ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X
GT30N LF W/O bezel SATA (HF + Windows 7)
PANASONIC NSM8XS ODD PANASONIC Super-Multi DRIVE 12.7mm Tray DL
8X UJ890A LF W/O bezel SATA (HF + Windows 7)
PLDS NBDCB4XS ODD PLDS BD COMBO 12.7mm Tray DL 4X DS-4E1S
LF W/O bezel SATA (Windows 7)
PLDS NSM8XS ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X DS-
8A4SH LF W/O bezel SATA (HF + Windows 7)
SONY NBDCB4XS ODD SONY BD COMBO 12.7mm Tray DL 4X BC-
5500H LF W/O bezel SATA (HF + Windows 7)
SONY NSM8XS ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X
AD-7585H LF W/O bezel SATA (HF + Windows 7)
TOSHIBA NSM8XS ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL 8X
TS-L633C LF W/O bezel SATA (HF + Windows 7)
204 Appendix B
VGA Chip
AMD MADISON_PRO AMD MADISON_PRO 40nm 29mm*29mm M2 package
AMD PARK_XT AMD PARK_XT 40nm 29mm*29mm M2 package
None UMA UMA (Intel)
VRAM
1G-DDR3 (64*16*8) 1G-DDR3 64*16*8
512M-DDR3 512M-DDR3 64*16*4
(64*16*4)
WiFi Antenna
WNC PIFA PIFA
Wireless LAN
Foxconn 3rd WiFi 2x2 BGN Foxconn Wireless LAN Atheros HB93 2x2 BGN (HM)
INTEL INT1000H Lan Intel WLAN 112BN.HMWG MM#903341
INTEL INT6200H Lan Intel WLAN 622AN.HMWG
Liteon 3rd WiFi 2x2 BGN Liteon Wireless LAN Atheris HB93 2x2 BGN (HM)
WN6602AH
Liteon 3rd WiFi 2x2 BGN Liteon Wireless LAN Atheris HB93 2x2 BGN (HM)
WN6602AH
Appendix B 205
206 Appendix B
Appendix C
Online Support Information

This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
• Service guides for all models
• User's manuals
• Bios updates
• Software utilities
• Spare parts lists
• TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
• Detailed information on Acer's International Traveler's Warranty (ITW)
• Returned material authorization procedures
• An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C 207
208 Appendix C
Index
A EasyTouch Failure 157

External Module Disassembly
AFLASH Utility 39
Flowchart 51
Antennas
Removing 104 F
B Features 1
Battery Pack
Flash Utility 39
Removing 52 FPC Cable
Replacing 137 Removing 101
Replacing 109
BIOS
ROM type 18 FRU (Field Replaceable Unit) List 177
vendor 18
Version 18
H
BIOS Utility27–39 Hard Disk Drive Modules
Advanced 30 Replacing 133
Boot 37 HDD1
Exit 38
Removing 60
Navigating 27
Replacing 133
Onboard Device Configuration 33
Power 35 HDD2
Save and Exit 38 Removing 62
Security 32 Replacing 133
System Security 38 HDTV Switch Failure 157
Board Layout
Hot Keys 14
Top View 169
I
C
Indicators 12
Camera Module
Intermittent Problems 159
Removing 98
Replacing 111 Internal Microphone Failure 147
Common Problems 140 Internal Speaker Failure 145
CPU
J
Removing 95
Replacing 114 Jumper and Connector Locations 169
CPU Fan
Removing 93
K
Replacing 115 Keyboard
D Removing 69
Replacing 129
DIMM Modules Keyboard Failure 143
Removing 57
Replacing 134 L
Display 5 LCD Bezel
E Removing 97
209
Replacing 112 N
LCD Brackets
Removing 101 No Display Issue 141
Replacing 109
O
LCD Failure 143
LCD Module ODD Failure 149
Removing 71 ODD Module
LCD Module Disassembly Replacing 135
Flowchart 96 Online Support Information 207
LCD Module Reassembly Procedure 106 P
LCD Panel
Removing 99 Panel 6
Replacing 109 Bottom 9
LED Board left 6
Removing 82 PC Card 12
Replacing 121 Power Board
Lower Covers Removing 100
Removing 54 Replacing 106
Replacing 135 Power On Failure 140
M Primary HDD
Removing 60
Main Module Reassembly Procedure 114 Replacing 133
Main Unit Disassembly
R
Flowchart 64
Mainboard RJ-11 Jack
Removing 90 Removing 91
Replacing 117 Replacing 116
Media Board RTC Battery
Removing 68 Removing 85
Replacing 130
Media Board FFC
S
Removing 81 SD Dummy Card
Memory Check 140 Replacing 137
MIC Board Secondary HDD
Replacing 133
Microphone Module
Speaker Module
Removing 103
Removing 83
Model Definition 190
Replacing 120
Modem Board
Switch Cover
Removing 86
Removing 65
Replacing 119 Replacing 131
Modem Cable System
Removing 91 Block Diagram 5
Replacing 116
210
T
Test Compatible Components 201
Thermal Grease 114
Thermal Module
Removing 94
Replacing 114
Thermal Unit Failure 157
TouchPad Bracket
Removing 80
Replacing 122
TouchPad Failure 144
Troubleshooting
Built-in KB Failure 143
EasyTouch Buttons 157
HDTV Switch 157
Internal Microphone 147
Internal Speakers 145
LCD Failure 143
No Display 141
ODD 149
Other Failures 158
Power On 140
Thermal Unit 157
TouchPad 144
WLAN 154
U
Undetermined Problems 159
Upper Cover
Removing 76
Replacing 122
USB Board
Removing 88
Replacing 118
utility
BIOS 27–39
W
Windows 2000 Environment Test 202
Wireless Function Failure 154
WLAN Module
Removing 58
Replacing 134
211
212

32 Service Manual - Packard Bell - Easynote Lj75 Lj77

Uploaded by

Copyright:

Available Formats

32 Service Manual - Packard Bell - Easynote Lj75 Lj77

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

32 Service Manual - Packard Bell - Easynote Lj75 Lj77

Uploaded by

Copyright:

Available Formats

www.SoporteTecnicoBsAs.com.

Repuestos para tus equipos.

Envios a Todo el Pais

Service guide files and updates are available

Dimensions and Weight

Special Keys and Controls

Component Icon Description

No. Component Icon Description

No. Component Icon Description

Component Icon Description

Component Icon Description

Battery latch Slide to release the battery.

Memory bay Memory modules are located in this bay.

Hard drive bay The hard drive is located in this bay.

Ventilation slots Helps cool internal components.

No. Component Description

No. Component Description

Bluetooth Num lock Battery

Num lock • LED on - Num lock is turned on

No. Icon Key Type Description

Function Key Description

Play/ Pause—Plays or pauses the CD or DVD.

Stop—Stops playing the CD or DVD.

Previous—Skips back one CD track or DVD chapter.

Next—Skips ahead one CD track or DVD chapter.

CPU Fan True Value Table)

*Check model number for specifications.

Hard Disk Drive Interface

Data heads 2/4

Power and Keyboard Controller

BIOS Setup Utility

Navigating the BIOS Utility

InsydeH20 Setup Utility Rev. 3.5

CPU Type Intel® Core™ i7

HDD Model Name: Hitachi HTS545016B9A300

System BIOS Version: V0.07

F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

InsydeH20 Setup Utility Rev. 3.5

Item Specific Help

F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

InsydeH20 Setup Utility Rev. 3.5

Item Specific Help

F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

Parameter Description Submenu Items

InsydeH20 Setup Utility Rev. 3.5

Item Specific Help

F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

Set Supervisor Password

Enter New Password [ ]

Set Supervisor Password

Enter Current Password [ ]

Set Supervisor Password

Enter Current Password [ ]

Changes have been saved.

The password setting is complete after the user presses Enter.

Passwords do not match.

InsydeH20 Setup Utility Rev. 3.5

Item Specific Help

F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default