Republic of the Philippines

Department of Education
Region IX, Zamboanga Peninsula
Division of Zamboanga Sibugay
Kabasalan National High School
F.L. Peña Sr., Kabasalan, Zamboanga Sibugay

Automotive Servicing
(Detailed Lesson Plan)

Student Teacher: Jestoni O. Ceniza BTTE IV-AT Date: January 10, 2020
Critic Teacher: Mr. Jonathan Magbanua Duration: 60 minutes
Grade/Section: Grade 9- Automotive
Subject: Automotive Shop

I. OBJECTIVES: At the end of the session the students are expected to;
a. Describe the ignition wiring installation process
b. Perform ignition wiring installation
c. Value the importance of ignition wiring installation process.
II. SUBJECT MATTER:
A. TOPIC: PERFORMING IGNITION WIRING INSTALLATION
B. TOOLS AND EQUIPMENT:
 Electrical pliers
 Set of screwdriver
 Wire stripper
 Soldering iron
 Engine mock-up
 Vehicle
C. Supplies and materials:
 Soldering leads
 Automotive wires
 Wire terminals
 Electrical tape
D. INSTRUCTIONAL MATERIAL:
 Visual aids
E. REFERENCE:
 Automotive Mechanics, 10th edition By: Crouse/ Anglin
 Modern Automotive Technology By: James E. Duffy
 Manufacturer’s Manual Toyota Corporation
III. PROCEDURE
TEACHER’S ACTIVITY STUDENTS ACTIVITY
A. Preliminary Activities
 Prayer
Please all stand for a prayer.
Mr. /Ms. ______lead the prayer. Dear God………….Amen

 Greeting
Good morning class. Good morning sir!
How are you today? Were fine sir.
Are you ready to learn new lesson today? Yes! Sir.
  Checking of Attendance None sir.
Ok class beadle me I know who is absent for
today?
Ok very good, for that give yourself a Clap3x…….Step3x…….Very good3x
Dionesia clap.

 Collecting Of Assignments None Sir.

Do you have an assignment class? Yes Sir, there is.
How about the agreement? Sir your instruction is to read in advance
And what is our agreement? about ignition wiring installation.
Yes Sir.
Ok, did you? Thank you sir.
Ok very good.

B. Review: Sir the topic that we discussed last

What did we discuss last meeting? meeting is all about the safety
measures in adjusting contact point.

Ok, did you still remember those safety measure in Yes Sir.
adjusting contact point?
Sir when testing a vehicle, never short
So what are those safety measure in adjusting plug lead to the dipstick, cam/rocker
contact point? Give me one. arm cover, battery or other components,
which may not be directly earthed. This
can cause an explosion of oil fumes or
hydrogen.

Beware of the danger from rotating

What else anyone? components of ignition system.

3. Never bend movable point arm with

Next. your hand.

4. Do not use the car, if the contact

Next. breaker point is not exactly adjusted to
the manufacturer specifications.

5. Do not install local contact point to

Next. the car of your customers and
replacement of part be checked
thoroughly, to avoid any trouble?

6. Use the proper screw driver for right

Next. head of bolt screw.

7. In replacing contact points do the

And the last one? same with the condenser or capacitor
used the required capacitance or farad.

And what else? Did you still remember the videos Yes Sir.
that I presented?
Thank you Sir.
Ok very good. Yes Sir.
I think you are all prepared now for the next topic.
DRILL
Motivation Yes Sir.
C. Presentation of the lesson:
So today you are going to perform “The Ignition
Wiring Installation Process”.

The reason why I ask you if you remember the

video presentation I have presented last meeting
because it has something to do of your performance Yes Sir.
for today.
OBJECTIVES: At the end of the
Are you ready to learn? session the students are expected to;
d. Describe the ignition wiring
Let us read first our objective for today’s lesson. installation process
e. Perform ignition wiring installation
f. Value the importance of ignition
wiring installation process.

D. Discussion
Unlocking the Difficulties

PROCEDURES IN CHECKING
IGNITION COMPONENTS WITH THE
The first thing to do before we perform wiring USE OF OHMETER:
installation is to check all the parts of ignition 1. Prepare the supplies, materials,
system if it is functional or not. tools and equipment needed.
2. Disconnect negative terminal of
Today we check the functionality of the components battery.
by using the ohmmeter. 3. Check Ignition switch by the use
of ohmmeter, RX1 one prod to
What are the procedures in checking the ignition AM while other prod to Ignition.
system components? Hand will move from infinity to
zero in two pull position of
ignition key – it’s okay.
4. Test auto wire from Ignition of
switch to positive terminal of coil,
RX1, hand move to infinity to
near zero – then it’s in proper.
5. Test auto wire from negative
terminal of coil to ground part of
distributor assembly open the
cap see the position of contact
point, RX1, if the contact point
open the hand remain infinity –
then it’s proper if hand will move
to zero the condition is grounded
contact point. If breaker points
close the hand will move near to
zero – then it’s proper.
 6. Test/check condenser, used
ohmmeter, RX1, connect one
prod to the eye tail of condenser,
and the other prod to the body
ground parts, the hand of meter
will move little bit abrupt to zero
side then, back to infinity side of
tester it’s proper – if does not
move or remain at infinity it is
defective, condenser is to be
replaced.
7. Test/check high tension wire
individually used ohmmeter RX
25Ω. Both prods of the meter will
be connected at both ends. See
the reading must be on the
specified ohms at all cords.
8. Check the adjustment of spark
plug gap by the used of feeler
gauge follow the gap
specification in the manual.
GAP ADJUSTMENT: Check the
plug gap with plug gap gauge. If not
to specified value, adjust by bending
the ground (outer) electrode. Plug
gap 0.8 mm (0.031 in) 1.0 mm
(0.039 in for USA).

E. Demonstration Prepare the supplies, materials, tools

Alright we can now check the ignition system and equipment needed.
components.
As I check the components of ignition Disconnect negative terminal of battery.
system, please read for me the procedures.

Okay let’s start. Read the first procedure.

We already prepared what we need. Next Check Ignition switch by the use of
procedure please. ohmmeter, RX1 one prod to AM while
other prod to Ignition. Hand will move
Done. Next procedure please. from infinity to zero in two pull position
of ignition key – it’s okay.

Alright. Another procedure. Reminder class Test auto wire from Ignition of switch to
that you really need to use the proper tool so positive terminal of coil, RX1, hand
it would fit the part. move to infinity to near zero – then it’s
in proper.
Next procedure.
Test/check condenser, used ohmmeter,
RX1, connect one prod to the eye tail of
 condenser, and the other prod to the
body ground parts, the hand of meter
Next procedure please. will move little bit abrupt to zero side
then, back to infinity side of tester it’s
proper – if does not move or remain at
infinity it is defective, condenser is to be
Next please. replaced.
Test/check high tension wire individually
used ohmmeter RX 25Ω. Both prods of
the meter will be connected at both
ends. See the reading must be on the
specified ohms at all cords.

Check the adjustment of spark plug gap

Another procedure. by the used of feeler gauge follow the
gap specification in the manual.

GAP ADJUSTMENT: Check the plug

gap with plug gap gauge. If not to
specified value, adjust by bending the
Last procedure. ground (outer) electrode. Plug gap 0.8
mm (0.031 in) 1.0 mm (0.039 in for
USA).

Thank you. After we check the components (re-demonstrate)

of ignition system we can now perform
ignition wiring installation.

F. Redemonstration

In this juncture, I need a student to re-demonstrate what I

did in front.
Let us help him by reading the procedures.

Very good, he really had done it nicely. Let us give him a

round of applause. Now I will group you into 2 groups. In
the right side is the group 1 while in the other side is the
group 2.

Direction: check components and perform ignition wiring

installation. Each group will choose a leader to present
their work and to ensure everyone will cooperate.

Rubric:
3 2 1
Accuracy If the If the If the
adjustme adjustme adjustme
nt is nt is nt is
accurate accurate wrong.
and and
procedur procedur
es are es are
 followed. not
followed.
Proper If they If the tool If they
handling used the used is used
& usage right tool correct incorrect (present their work)
of tools and but didn’t tools.
handled handled
it it
properly. properly.
Group 1:
Group 2:

Now the group leaders will come in front and present their
work.

Very good, I Guess you learned something from our

lesson for today. Let us give a hand to everyone.

IV. EVALUATION:
1) What tool we are going to use when measuring the clearance of the
contact point?
a. Feeler gauge b. Socket wrench c. Screw drivers
2) What device are we going to use when reading resistance?
a. Feeler gauge b. ohmmeter c. Screw drivers
3) What do you call the tool that loosen and tighten screws?
a. Feeler gauge b. Socket wrench c. Screw drivers
4) What do you call the tool that tighten and loosen nuts and bolts?
a. Feeler gauge b. Socket wrench c. Screw drivers
5) What is the specified spark plug gap of U.S.A.?
a. 1cm b. 1mm c.1dm
V. ASSIGNMENT:
Research the ignition wiring connection of ignition system.