Section : 4S11

Type : RC Slab Design

Design Code : BS8110:2000
Prepared By : Date : 7/4/2020
Project : Checked By : MPA Job ID : ST03
Two-Way Slab Design (Based on BS8110:2000-Part1)
***********************************
Slab Marking = 4S11 _4th Story Edge 1
DESIGN INFORMATION
Material Data

Edge 2
Lx
Concrete Strength, fcu = 30 N/mm2

Edge
Steel Strength of Bent-up Bars, fyb = 460 N/mm2
Ly
Steel Strength of Stirrups, fys = 460 N/mm2
Concrete Desity, = 24 kN/m3
Aggregate Size, hagg = 20 mm
Edge 3
Slab Data
Short Span Length, Lx = 5.8 m
Long Span Length, Ly = 6.5 m
Span Ratio, Ly/Lx = 1.20 <= 2.0 Slab Data
Hence, the Slab is Two-way. Edge 1= D
Slab Thickness, h = 200 mm Edge 2= C
Top Cover = 25 mm Edge 3= D
Bottom Cover = 25 mm Edge 4= D
Main Span Length, L = 5.8 m
Loading Analysis
Self Weight of Slab = 4.8 kN/m2 P
Finishing+Ceiling+M&E = 1.5 kN/m2
Brick Wall = 0.0 kN/m2
Column Point Load PDL = 0.0 kN
= 0.0 kN/m2 L
Total Dead Load, DLT = 6.3 kN/m2
Imposed Live Load, LL = 1.5 kN/m2
Column Point Load PLL = 0.0 kN
= 0.0 kN/m2
Total Live Load LLT = 1.5 kN/m2
Total Factored Load, n=1.4 DLT+1.6LLT = 11.2 kN/m2
Nd= 3
MAIN STEEL Flexural Design Short Long Edge 1 Edge 2 Edge 3 Edge 4 ϒ= 0.223
Parameter Span,x Span,y Discont' Cont' Discont' Discont'
β 0.056 0.044 0.000 0.058 0.000 0.000 (BS8110:Table 3.14)
M (kNm) 21.06 16.42 0.00 21.89 0.00 0.00
d (mm) 170.0 160.0 170.0 160.0 170.0 160.0
k' 0.156 0.156 0.156 0.156 0.156 0.156
k 0.024 0.021 0.000 0.029 0.000 0.000
Z (mm) 161.5 152.0 161.5 152.0 161.5 152.0
As,req (mm2/m) 325.8 269.9 0.0 359.9 0.0 0.0
As,min(mm2/m) 260.0 260.0 260.0 260.0 260.0 260.0
Ø (mm) 10 10 10 10 10 10
Layer B1 B2 T1 T2 T1 T2
Spacing (mm) @ 150 150 150 150 150 150
As,prov(mm2/m) 524 524 524 524 524 524 [OK] (Main Bar Steel)
100As,prov/bd (%) 0.308 0.327 0.308 0.327 0.308 0.327
As',prov(mm2/m) 0 0 0 0 0 0 (If Comp. Steel provd')
Smax (mm) 520 490 520 490 520 490 [OK] (Max. Spacing)
fs (N/mm2) 191 158 0 211 0 0
 Section : 4S11
Type : RC Slab Design
Design Code : BS8110:2000
Prepared By : Date : 7/4/2020
Project : Checked By : MPA Job ID : ST03
CHECK SHEAR
Shear Design Edge 1 Edge 2 Edge 3 Edge 4 Sum βvx = 0.664
Parameter Discont' Cont' Discont' Discont' Sum βvy = 0.75
βv 0.332 0.450 0.332 0.300 (BS8110:Table 3.15)
V (kN/m) 21.61 29.28 21.61 19.52
v (N/mm2) 0.13 0.18 0.13 0.12 ≤ 0.8√fcu = 4.382 kN/m2 [OK]
vc (N/mm2) 0.56 0.58 0.56 0.58 > v [OK]
Shear Reinforcement is not required.
CHECK DEFLECTION
Moment Distribution Factor, βb = 1.0
M/bd^2 = 0.73
2
Modification Factor, M.Ftension = 0.55+(477-fs)/(120(0.9+M/bd ))
= 2.01 > 2.0
100As'prov'd/bd = 0.000 (For Compression Steel)
Modification Factor, M.FComp = 1+(100As'prov'd/bd)/(3+100 As'prov'd/bd)
= 1.00 < 1.5
Allowable Span-Effective Depth ratio, L/d = 40.00
Actual L/d = 34.12 < Allow. L/d [OK]