Wuerz elektronik

Im Burgfeld 4; D-35781 Weilburg

Tel.: ++49 6471 629 884; Fax:++49 6471 629 885
Mail: [email protected]
http://www.wuerz-elektronik.com

ec5554 Microcontroller Module

Product Information

Status: May 2006

 TPU , QSPI , RS232 x 2, TouCAN x 3, I/O

Three CAN Transceiver

sync.
Burst- Burst
MPC5554 SRAM Flash-
120 MHz 256 /512 Kb/
40 Channel AD-Converter

EPROM
1 M x 32-bit 1Mx
2 M x 32 bit 32bit

JTAG 14 pin

Two RS232 Driver

Burst- sync.
SRAM Burst
256 /512 Kb/ Flash-
1 M x 32-bit EPROM
2 M x 32-bit 1Mx
32 bit

32-bit expansion System-Bus for external devices (8, 16, 32 bit)

Microcontroller Module with Motorola Processor MPC5554.

The module “ec5554“ made by Wuerz elektronik is a credit-card sized module with the Motorola processor
MPC5554. The MPC5554 is a RISC MCU with a 32 bit PowerPC architecture The processor operates at
132MHz. The processor provides:
Enhanced 64-channels direct memory access (eDMA) controller
On-chip FLASH, 2 Mbytes (MPC5554) burst Flash memory 256K × 64 bit configuration
On-chip 96 kilobyte internal static RAM (SRAM)
Enhanced modular I/O system (eMIOS)
24 orthogonal channels with double action, PWM, and modulus counter functionality
4 (MPC5554) or 3 (MPC5553) deserial serial peripheral interface modules (DSPI)
SPI 2 enhanced serial communication interface (eSCI) modules
UART mode provides NRZ format and half or full duplex interface, eSCI bit rate up to 1 Mbps
3 (MPC5554) FlexCANs
Nexus development interface (NDI)
MPC5554 has two eTPU engines, 32 channels per engine
Enhanced queued analog/digital converter (eQADC), 40 single-ended inputs channels with 12-bit A/D
resolution , common mode conversion range of 0–5V

The design intention of the module, sized 79 x 60 mm, was a stand-alone solution for embedded ap-
plications. The module can have up to 16 M Byte external Burst-Flash-EPROM (2 M*32 bit), up to 16
M Byte synchronous Burst SRAM , two RS232 drivers and three CAN interfaces. The module is “CAN-
Ready” for transfer rates up to 1 Mbps. A 14 pin JTAG debug interface can be used to program the
internal and the external flash-EPROM via debug software. All processor signals are accessible on
three SMD connectors. Pins spacing 0,8 mm. The module is available for an expanded temperature
range .Single 5 Volt Power Supply.
An Evaluationboard, with a100 base ETHERNET controller and a NEXUS degug interace , for
the development of applications is available. A Power Supply in the wide input range from +6V
up to +45V can be used.
 Top-View

Burst SRAM

JTAG-Interface
Burst SRAM

Bottom-View

Systembus J1
MAX232A

A/D Converter
J3 CAN1
CAN2
CAN3

3 x 82C250

I/O Bus J2
Two sync. Burst Flash-EPROMs
32 bits wide each
Bus configuration of the ec5554 Module
BUS J1-141 BUS J2-141

J1-A J1-B J2-A J2-B

+5V 1 +5V ETPUA31 1 ETPUB31

+5V 2 +5V ETPUA30 2 ETPUB30

GND 3 GND ETPUA29 3 ETPUB29

GND 4 GND ETPUA28 4 ETPUB28

GND 5 GND ETPUA27 5 ETPUB27

+3.3V 6 +3.3V ETPUA26 6 ETPUB26

MD0 7 EVTO ETPUA25 7 ETPUB25

MD1 8 EVTI ETPUA24 8 ETPUB24

MD2 9 MSEO0 ETPUA23 9 ETPUB23

MD3 10 MSEO1 ETPUA22 10 ETPUB22

MD4 11 RDY ETPUA21 11 ETPUB21

MD5 12 TEST ETPUA20 12 ETPUB20

MD6 13 JOOMP ETPUA19 13 ETPUB19

MD7 14 TMS ETPUA18 14 ETPUB18

MD8 15 TDO ETPUA17 15 ETPUB17

MD9 16 TDI ETPUA16 16 ETPUB16

MD10 17 TCK ETPUA15 17 ETPUB15

MD11 18 RD/*WR ETPUA14 18 ETPUB14

MCK0 19 WE1 ETPUA13 19 ETPUB13

OE 20 WE3 ETPUA12 20 ETPUB12

WEO 21 TSIZ1 ETPUA11 21 ETPUB11

WE2 22 TS ETPUA10 22 ETPUB10

TSIZ0 23 IRQ5_PLLCFG1 ETPUA09 23 ETPUB09

BDIP 24 BOOTCFG0_IRQ2 ETPUA08 24 ETPUB08

NC 25 TCRCLKA_IRQ7_GPIO113 ETPUA07 25 ETPUB07

TA 26 CLKOUT ETPUA06 26 ETPUB06

TEA 27 ENGCLK ETPUA05 27 ETPUB05

IRQ4_PLLCFG0 28 CS1 ETPUA04 28 ETPUB04

BOOTCFG1_IRQ3 29 CS3 ETPUA03 29 ETPUB03

RESET 30 CS0 ETPUA02 30 ETPUB02

PCSB5 31 CS2 ETPUA01 31 ETPUB01

PCSB4 32 RSTOUT ETPUA00 32 ETPUB00

PCSB2 33 PCSB4 EMIOS00 33 EMIOS01

PCSB0 34 PCSB3 EMIOS02 34 EMIOS03

SINB 35 PCSB1 EMIOS04 35 EMIOS05

PCSA5 36 SOUTB EMIOS06 36 EMIOS07

PCSA3 37 SCKB EMIOS08 37 EMIOS09

PCSA1 38 PCSA4 EMIOS10 38 EMIOS11

SOUTA 39 PCSA2 EMIOS12 39 EMIOS13

SCKA 40 PCSA0 EMIOS14 40 EMIOS15

B8 41 SINA EMIOS16 41 EMIOS17

BG 42 BR EMIOS18 42 EMIOS19

A30 43 A31 EMIOS20 43 EMIOS21

A28 44 A29 EMIOS22 44 EMIOS23

A26 45 A27 GPIO207 45 GPIO206

A24 46 A25 GPIO205 46 GPIO204_EMIOS15

A22 47 A23 GPIO203_EMIOS14 47 CFG0

A20 48 A21 PLL0 48 CFG1

A18 49 A19 PLL1 49 RTSCONF/GPIO210

A16 50 A17 NC 50 WKPCFG

A14 51 A15 RESIN 51 TCRCLKB

A12 52 A13 VSTBY 52 NC

A10 53 A11 NC 53 NC

A08 54 A09 NC 54 NC

D30 55 D31 NC 55 WP_EXTFL

D28 56 D29 UBAT_IN 56 UBAT

D26 57 D27 TXD_A 57 RXD_A

D24 58 D25 TXD_B 58 RXD_B

D22 59 D23 TXD1-RS232 59 RXD1-RS232

D20 60 D21 TXD2-RS232 60 RXD2-RS232

D18 61 D19 GND 61 GND

D16 62 D17 CNTX_C 62 CNRX_C

D14 63 D15 CNTX_B 63 CNRX_B

D12 64 D13 CNTX_A 64 CNRX_A

D10 65 D11 GND 65 GND

D08 66 D09 CAN_H3 66 CAN_L3

D06 67 D07 CAN_H2 67 CAN_L2

D04 68 D05 CAN_H1 68 CAN_L1

D02 69 D03 GND 69 GND

D00 70 D01 NC 70 NC
Configuration AD converter

ADconverter J3

J3-A J3-B
VDAA 1 VSSA
VRH 2 VRL
ETRIG1 3 ETRIG0
AN00 4 ANO1
AN02 5 AN03
GND 6 AN05
AN04 7 AN07
AN06 8 AN09
AN08 9 AN11
AN10 10 AN13
AN12 11 AN15
AN14 12 GND
GND 13 AN17
AN16 14 AN19
AN18 15 AN21
VDDA 16 GND
VSSA 17 AN23
AN20 18 AN25
AN22 19 GND
AN24 20 AN27
AN26 21 AN29
GND 22 AN31
AN28 23 GND
AN30 24 AN33
AN32 25 AN35
AN34 26 GND
AN36 27 AN37
GND 28 AN39
AN38 29 GND
VSSA 30 VDDA
Technical Specifications
Board Multilayer 79 x 60 mm, height 9 mm, weight 30 gram

Main Processor MPC5554 /MPC5553

Motorola e500 Core
High-performance 50–150 MHz 32-bit PowerPC Architecture
Memory management unit (MMU) with 24-entry fully associativ
translation lookaside buffer (TLB)
Enhanced queued analog-to-digital converter (eQADC)
Four deserial serial peripheral interfac (DSPI) modules
Three controller area network (FlexCAN) modules
Two enhanced serial communication interface (eSCI) modules
Eighty-eight channels of timed I/O
Two enhanced time processor units (eTPUs)

Static RAM two 32-bit organized synchronous Burst SRAMs up to 16 MByte

(256K x 32-bit), (512K x 32-bit), (1 M x 32 bit) or (2 M x 32 bit)

Flash-Memory two 32-bit organized Burst Mode, Dual Boot, Flash devices,
512k (32 Megabit) or 1M Types (64 Megabit), 2.5 Volt types

Utilities Triple Supervisory Circuit

Serial Interface The Processor has two SCI (Serial Communication Interfaces)
each SCI Channel consists of one RXD and one TXD. The two
SCI Channels are driven by one MAX232A -RS232 Transceiver
(116kbit/s).

CAN Interface Three CAN-Interfaces. Each CAN-Interface has its own

PCA82C250T Transceiver.
The physically interface is according to ISO/DIS 11898

PCB-Layer 8 Layers

Operating Temp. -40°C to +85°C

Connectors Three connectors AMP 0,8 mm spacing, number of pins: 340

Power Supply Single 5 Volt, 700 mA

ROM Monitor included

The ROM Monitor supports programming of the internal and
external Flash. Downloading of S-Records and binary Data files
 Evaluationboard for the ec5554 module

Size 144 x 155 mm

Power supply 6V to 40 V input

JTAG 14 pin
All signals are available on male headers spacing 2,54mm /100mil

MICTOR 38-pin NEXUS debug

ec5554 module

CAN-3 CAN2/CAN1 Rs232 1/2 100base ETHERNET