A Simple Guide To

Download as doc, pdf, or txt
Download as doc, pdf, or txt
You are on page 1of 2

A simple guide to crack WPA

You must be running the latest Backtrack 5 R2 download from http://www.backtrack-


linux.org/downloads/ choose GNOME 32 bit, this Backtrack version already have many new command
like wash and reaver install and it is ready to be use, but for my customer who already have the
backtrack dvd than you save a lot of time downloading it. But make sure u unzip the backtrack to a
folder u remember and open with vmware

You must have a wireless card capable of raw injection, My recommended wireless for more stable
connection and injection is Alfa AWUS036H or Alfa AWUS036NHR, the good about AWUS036NHR( will
detect in backtrack as rtl8192, is it can detect N signal perfectly as well as G Signal while AWUS036H is
perfect for G signal

Once Back Track is downloaded, you have 2 choice

1) Boot from DVD rom to run it


2) Run it from windows using vmware if you know it and where to download it, there is plenty of
place to download vmware with google search whice I don’t need to guide you, The best for
using VMware is you can running backtrack with your windows together

When Running VMware,, remember, Make sure your wireless card is plug in to your usb port.
Vmware will detect the card, But many have forget of donno that they must active the wifi card in
vmware, to do this, look at the right bottom of your vmware,there is a wificard icon, click on it and
you will have an option to connect or disconnected from host, connect it.

Backtrack tips:

When backtrack is started in a console screen, it may ask for login and password ( depend on
backtrack version) the login is root and password is toor

After this, wait for a moment until backtrack loading is stop lie this

rootbt:

Type startx…..

rootbt: startx

then just click enter and the basic following command is ( press enter on each)

1) airmon-ng
2) airmon-ng start wlan0
this is call monitor mode for your wifi card
You must put your wireless card into monitor mode. This is most easily done using airmon-ng from
the aircrack-ng tool suite.

Basic Usage

First, make sure your wireless card is in monitor mode:

root@bt:~# airmon-ng start wlan0

root@bt:~#wash -i mon0 (to scan for valid Wifis.) copy the bssid and paste in reaver

The best is close the wash console and open up a new console in backtrack interface than….

To run Reaver, you must specify the BSSID of the target AP and the name of the monitor mode
interface (usually 'mon0', not 'wlan0', although this will vary based on your wireless card/drivers):

root@bt:~# reaver -i mon0 -b bssid -vv

You will probably also want to use -vv to get verbose info about Reaver's progress:

root@bt:~# reaver -i mon0 -b 00:01:02:03:04:05 –vv

To make u more understand, I will link you to a youtube website for more information

http://www.youtube.com/watch?v=cxXfCX4HIUE

ok to not wasting time and bored skip this video up to 2:9 minutes than you learn from there which I
already teach you, is ok to keep watch and watch because the more you watch, the more you
understand, the reason I ask you to skip the beginning is because you don’t need to learn how to
install reaver because reaver is already build it in the backtrack 5 R2 you download.

Once reaver is running, just wait and let reaver do the job till 100% sometimes if you are lucky you
will get the wpa password in 10 minutes, but if you are unlucky it may take days for reaver to reach
100% running, successful rate is 99%, just leave reaver running and it is just the matter of time when
the password will be show up.

You might also like