Scribd
Upload
456 views3 pages

Pdms Setup Mds - Pdms Macro

1. To set up MDS in PDMS, open a project, create MDS and MDU teams, and include specific MDS and MDU databases from those projects. 2. Copy required files from the MDS project folder to the defaults project folder. 3. Go to Paragon and activate the necessary MDS supports, then create zones in Design with the purpose of SUPP.

Uploaded by

SameerChauhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
456 views3 pages

Pdms Setup Mds - Pdms Macro

1. To set up MDS in PDMS, open a project, create MDS and MDU teams, and include specific MDS and MDU databases from those projects. 2. Copy required files from the MDS project folder to the defaults project folder. 3. Go to Paragon and activate the necessary MDS supports, then create zones in Design with the purpose of SUPP.

Uploaded by

SameerChauhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

01/07/2020 How to Setup MDS?

| PDMS Macro

PDMS Macro

PDMS LEARNING AND MACRO DOWNLOAD

How to Setup MDS?

08 MAY
1. Open PDMS, select the project (example SAM) and go to Admin module.
2. Create 2 teams namely MDS and MDU, put the SYSTEM user to MDS and MDU team.
3. Include following databases (as a minimum) from MDS project (use username SYSTEM, password
XXXXXX)
a. MDS/CATA
b. MDS/DESITMPL-AISC
c. MDS/DESITMPL-GRI
d. MDS/DRAFT
e. MDS/MDSAPPDEFAULTS
f. MDS/PROP
g. MDS/WELDS
4. Include the following database from MDU project
a. MDU/CATA
5. Include the databases mentioned earlier to desired MDB.
6. Copy following file from MDSDFLTS folder (the folder under MDS project directory) to defaults
project folder (SAMDFLTS, under the SAM project directory). Forget to copy these files and you’ll
get errors.
a. DES-SUPP-NAMES
b. DRA-SUPP-DEFS
c. MDS-REPORT-DEFS
d. MdsUserData.pmldat
7. Go to Paragon and activate required MDS supports.
8. Go to Design and create Zones with purpose SUPP

6 Comments
Posted by pdmsmacro on May 8, 2014 in PDMS Training and Knowledge

Tags: How to setup MDS, MDS Administration, MDS setup

6 responses to “How to Setup MDS?”

mehdi

July 15, 2014 at 5:43 am

https://pdmsmacro.wordpress.com/2014/05/08/how-to-setup-mds/ 1/3
01/07/2020 How to Setup MDS? | PDMS Macro

it was very good. it solved my problem.


thanks.

Reply

Raalingeswara Reddy

March 15, 2015 at 12:41 pm

Hi How to Activate From PARAGON Module.

Reply

tifatul sembiring

March 14, 2015 at 7:36 am

Hi Pak,

what are the possible reasons why I can’t identify tube of datum pipe when trying to create datum
pipe for MDS support?

Thanks.

Reply

pdmsmacro

March 16, 2015 at 4:25 am

have you added MDS Tee in the specificatio?

Reply

Ramalingeswara reddy

March 16, 2015 at 4:03 am

Hi How to Activate MDS From PARAGON

Reply

pdmsmacro

March 16, 2015 at 4:27 am

you can read the MDS manual.

Reply

Blog at WordPress.com.

Entries (RSS) and Comments (RSS)

https://pdmsmacro.wordpress.com/2014/05/08/how-to-setup-mds/ 2/3
01/07/2020 How to Setup MDS? | PDMS Macro

https://pdmsmacro.wordpress.com/2014/05/08/how-to-setup-mds/ 3/3

You might also like