PSCS 10-3,6V

EN
OPERATING MANUAL
CORDLESS BATON
SCREWDRIVER
TRT-BA-TRT-BA-PSCS10-3,6V-TC-001-EN
table of contents Follow the manual
Information marked with this symbol indicates that the
Notes regarding the operating manual................................. 1 operating manual must be observed.

Safety ..................................................................................... 2 Wear safety glasses

Information marked with this symbol indicates that you
Information about the device................................................ 6 should wear eye protection.
Transport and storage........................................................... 8 Wear a protective mask
Start-up.................................................................................. 9 Information marked with this symbol indicates that you
should wear a protective mask.
Operation ............................................................................. 11
Wear Ear Protection
Available accessories.......................................................... 13 Information marked with this symbol indicates that you
should wear hearing protection.
Errors and faults.................................................................. 13
The current version of the operating manual can be found at:
Maintenance ........................................................................ 14
Disposal ............................................................................... 14
PSCS 10-3,6V

Notes regarding the operating manual

Symbols http://download.trotec.com/?sku=4410000005&id=1

Warning of electrical voltage Legal notice

This symbol indicates dangers to the life and health of
This release replaces all previous versions. No part of this
persons due to electrical voltage.
publication may be reproduced without written permission from
Warning of explosive substances Trotec GmbH & Co. KG. The same applies for electronically
This symbol indicates dangers to the life and health of processing, duplicating or spreading the publication. Subject to
persons due to potentially explosive substances. technical changes. All rights reserved. Trademarks are used
without guarantee that they may be used freely and primarily
Warning! following the spelling of the manufacturer. Product names are
This signal word indicates a hazard with an average registered.
risk level which, if not avoided, can result in serious Changes to construction in the interests of constant
injury or death. improvements to the product, as well as changes to the shape
Caution! and colour are reserved.
This signal word indicates a hazard with a low risk The scope of delivery may vary from product images. This
level which, if not avoided, can result in minor or document was created with all due care. Trotec GmbH & Co. KG
moderate injury. accepts no liability whatsoever for possible mistakes or
omissions.
Note
© Trotec GmbH & Co. KG
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.

1 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

Warranty and liability Safety
The device complies with the fundamental health and safety
Read this manual carefully before starting or using the
requirements of the applicable EU regulations and was tested at
the factory for perfect functionality multiple times. device. Always store the manual in the immediate vicinity
of the device or its site of use!
However, if faults in the functionality occur and cannot be
remedied with the measures in the chapter Errors and faults, Warning
please get in touch with your dealer or distributor. Read all safety warnings and all instructions.
When making a warranty claim, supply the device number (see Failure to follow the warnings and instructions may
the side of the device). result in electric shock, fire and/or serious injury.
When manufacturer's instructions or legal regulations have not Save all warnings and instructions for future
been followed, or after unauthorised changes to the device are reference.
made, the manufacturer is not responsible for the resulting This appliance can be used by children aged from 8
damages. Changes to the device or unauthorised replacement years and above and persons with reduced physical,
of individual parts can drastically impact the electrical safety of sensory or mental capabilities or lack of experience
this product and will result in the loss of the warranty. Liability and knowledge if they have been given supervision or
does not extend to damages to people or property caused by the instruction concerning use of the appliance in a safe
device being used other than as described in the instructions in way and understand the hazards involved.
this operating manual. Subject to changes to technical design Children shall not play with the appliance. Cleaning and
and model changes as part of constant development and user maintenance shall not be made by children
product improvement without prior notice. without supervision.
No liability is accepted for damages resulting from improper General Power Tool Safety Warnings – Work area
use. In such a case, any warranty claims will be voided also. safety

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.
• Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
• Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 2

 General Safety Warnings – Electrical safety General Power Tool Safety Warnings – Personal
safety

• Power tool or power adapter plugs must match the • Stay alert, watch what you are doing and use common
outlet. Never modify the plug in any way. Do not use sense when operating a power tool. Do not use a
any adapter plugs with earthed (grounded) power power tool while you are tired or under the influence of
tools. Unmodified plugs and matching outlets will reduce drugs, alcohol or medication. A moment of inattention
risk of electric shock. while operating power tools may result in serious personal
• Avoid body contact with earthed or grounded surfaces, injury.
such as pipes, radiators, ranges and refrigerators. Use personal protective equipment. Always wear
There is an increased risk of electric shock if your body is eye protection. Protective equipment such as dust
earthed or grounded. mask, non-skid safety shoes, hard hat, or hearing
• Do not expose power tools to rain or wet conditions. protection used for appropriate conditions will reduce
Water entering a power tool will increase the risk of personal injuries.
electric shock. • Prevent unintentional starting. Ensure the switch is in
• Do not abuse the cord. Never use the cord for carrying, the off-position before connecting to power source
pulling or unplugging the power tool. Keep cord away and/or battery pack, picking up or carrying the tool.
from heat, oil, sharp edges or moving parts. Damaged Carrying power tools with your finger on the switch or
or entangled cords increase the risk of electric shock. energising power tools that have the switch on invites
• When operating a power tool outdoors, use an accidents.
extension cord suitable for outdoor use. Use of a cord • Remove any adjusting key or wrench before turning
suitable for outdoor use reduces the risk of electric shock. the power tool on. A wrench or a key left attached to a
• If operating a power tool in a damp location is rotating part of the power tool may result in personal
unavoidable, use a residual current device (RCD) injury.
protected supply. Use of an RCD reduces the risk of • Do not overreach. Keep proper footing and balance at
electric shock. all times. This enables better control of the power tool in
• Hold power tool by insulated gripping surfaces when unexpected situations.
performing an operation where the cutting accessory • Dress properly. Do not wear loose clothing or
may contact hidden wiring or its own cord. Cutting jewellery. Keep your hair, clothing and gloves away
accessory contacting a "live" wire may make exposed from moving parts. Loose clothes, jewellery or long hair
metal parts of the power tool "live" and could give the can be caught in moving parts.
operator an electric shock. • If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.

3 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

 General Power Tool Safety Warnings – Power tool General Battery Pack / Charger Safety Warnings
use and care

• Do not force the power tool. Use the correct power tool • Use power tools only with specifically designated
for your application. The correct power tool will do the battery packs. Use of any other battery packs may create
job better and safer at the rate for which it was designed. a risk of injury and fire.
• Do not use the power tool if the switch does not turn it • When battery pack is not in use, keep it away from
on and off. Any power tool that cannot be controlled with other metal objects, like paper clips, coins, keys, nails,
the switch is dangerous and must be repaired. screws or other small metal objects, that can make a
• Disconnect the plug from the power source and / or connection from one terminal to another. Shorting the
the battery pack from the power tool before making battery terminals together may cause burns or a fire.
any adjustments, changing accessories, or storing • Recharge only with the charger specified by the
power tools. Such preventive safety measures reduce the manufacturer. A charger that is suitable for one type of
risk of starting the power tool accidentally. battery pack may create a risk of fire when used with
• Store idle power tools out of the reach of children and another battery pack.
do not allow persons unfamiliar with the power tool or • Do not charge other battery packs. The charger is only
these instructions to operate the power tool. Power suitable for use with the supplied battery pack and with
tools are dangerous in the hands of untrained users. the voltages specified in the technical data. Otherwise,
• Maintain power tools. Check for misalignment or there is a risk of fire and explosion.
binding of moving parts, breakage of parts and any • Under abusive conditions, liquid may be ejected from
other condition that may affect the power tool’s the battery; avoid contact. If contact accidentally occurs,
operation. If damaged, have the power tool repaired flush with water. If liquid contacts eyes, additionally seek
before use. Many accidents are caused by poorly medical help. Liquid ejected from the battery may cause
maintained power tools. irritation or burns.
• Keep cutting tools sharp and clean. Properly maintained • In case of damage and improper use of the battery,
cutting tools with sharp cutting edges are less likely to vapours may be emitted. Provide for fresh air and seek
bind and are easier to control. medical help in case of complaints. The vapours can
• Use the power tool, accessories and tool bits etc. in irritate the respiratory system.
accordance with these instructions, taking into • Do not open the battery. There is danger of a short
account the working conditions and the work to be circuit.
performed. Use of the power tool for operations different • Do not short-circuit the battery. There is danger of
from those intended could result in a hazardous situation. explosion.
General Power Tool Safety Warnings – Service • Batteries must not be exposed to mechanical impacts.
• Protect electrical parts against moisture. To prevent an
electric shock, never immerse them in water or other
• Have your power tool serviced by a qualified repair liquids during cleaning or operation. Never hold the
person using only identical replacement parts. This will charger under running water. Please observe the
ensure that the safety of the power tool is maintained. instructions for cleaning and maintenance.
• The charger is only suited for indoor use.
• Keep the charger clean. Contamination entails a risk of
electric shock.

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 4

• Do not operate the charger on highly combustible ground Warning of electrical voltage
(e.g. paper, textiles etc.) or in an inflammable environment. There is a risk of a short-circuit due to liquids
The heat generated by the charger during charging entails penetrating the housing!
a risk of fire. Do not immerse the device and the accessories in
• Only use the charger for charging the battery. The charger water. Make sure that no water or other liquids can
must not be used as power supply for the power tool. enter the housing.
Warning of electrical voltage
Device-specific safety warnings for cordless
Work on the electrical components must only be
screwdrivers
carried out by an authorised specialist company!
Wear eye and mouth protection when processing Warning of explosive substances
materials that may contain harmful substances (e.g.
Do not expose the battery to temperatures above 45
asbestos).
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
• Secure the workpiece with tensioning devices or a vice. risk of explosion!
• Hold the power tool firmly. When tightening or loosening Warning!
screws, high reaction torques can occur temporarily. Toxic dusts!
• Immediately switch off the power tool if the insertion tool The harmful / toxic dusts produced during operation
blocks. Beware of high reaction torques causing a pose of risk to the health of the operator and persons
kickback. in the vicinity.
• Hold power tool by insulated gripping surfaces when Wear eye protection and a protective mask!
performing an operation where the cutting accessory Warning!
may contact hidden wiring. Cutting accessory contacting Do not process materials containing asbestos.
a "live" wire may make exposed metal parts of the power Asbestos is considered carcinogenic.
tool "live" and could give the operator an electric shock.
• For any work on the device, as well as during transport or Warning!
storage, set the switch for the rotational direction to centre Make sure not to hit power, gas or water lines when
position (locked). This prevents unintentional starting of the working with a power tool.
power tool. If necessary, use a pipe detector to check the wall you
want to drill in or slit open.
Residual risks – cordless drill drivers
Warning!
Warning of electrical voltage Risk of injuries caused by flying parts or bursting tool
Electric shock from insufficient insulation. heads.
Check the device for damages and proper functioning
before each use. Warning!
If you notice damages, no longer use the device. Dangers can occur at the device when it is used by
Do not use the device when the device or your hands untrained people in an unprofessional or improper way!
are damp or wet! Observe the personnel qualifications!

Warning of electrical voltage Warning!

Before any work on the device, remove the mains plug Do not leave the packaging lying around. Children may
from the mains socket and the battery from the device! use it as a dangerous toy.
Hold onto the mains plug while pulling the power cable Warning!
out of the mains socket. The device is not a toy and does not belong in the
hands of children.

5 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

 Caution! The tool holder with locking mechanism further enables an easy
Vibration emissions can cause a health hazard if the and tool-free exchange of the insertion tools.
device is used for an extended period of time or if it is The integrated LED work lamp offers an improved illumination of
not properly handled and maintained. the workpiece or working surface.
Caution! Device depiction
Keep a sufficient distance from heat sources.
1 2 3
Caution!
While the battery is charging, the handle may become 4
slightly warm. This is normal.
Note
5
To avoid damaging the gear, only change the rotational
direction when the device is at a standstill. 6
13
Note
Set the torque and rotational direction according to the 12
operating mode. A wrong selection may damage the 7
device.
Note 8
If you store or transport the device improperly, the
device may be damaged.
9
Note the information regarding transport and storage of
the device.
10
Intended use
Only use the device PSCS 10-3.6V:
• for screwing in and loosening screws,
• for drilling in wood, plastic, ceramic and metal, 11
whilst adhering to the technical data.

Improper use
The device is not intended for drilling in concrete or natural
stone.

Personnel qualifications No. Designation

1 Tool holder with locking mechanism
People who use this device must:
• have read and understood the operating manual, especially 2 Torque selection
the Safety chapter. 3 3-stage battery level indication
4 Handle position switch
5 Clockwise / counter-clockwise rotation, lock
Information about the device
6 Handle
Device description 7 Charger connection
The cordless baton screwdriver has an adjustable handle that 8 25 mm bit
can be positioned horizontally or vertically to the screw bit. 9 50 mm bit
10 Magnetic bit holder
The integrated torque selection, including one drilling setting,
allows you to use the optimum power for every application, 11 Charger
adapted to the material and screw size. 12 On / off switch
13 LED work lamp

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 6

Scope of delivery Information on noise and vibration:
• 1x Cordless baton screwdriver • The vibration level specified in these instructions was
determined by means of a measuring method standardized
• 1x Charger
in EN 60745 and can be used for a device comparison. The
• 24x Bits 25 mm specified vibration emission value may also be used for a
• 2x Bits 50 mm preliminary assessment of the exposure.
• 1x Magnetic bit holder
Caution!
• 1x Transport case Vibration emissions can cause a health hazard if the
• 1x Manual device is used for an extended period of time or if it is
not properly handled and maintained.
Technical data • The vibration level will change depending on the
Parameter Value application of the power tool and may in some cases differ
Model PSCS 10-3.6V from the value specified in these instructions. The vibration
Nominal voltage 3.6 V load may be underestimated if the power tool is used
Idle speed 200 rpm regularly in such a way. For a precise estimation of the
Torque settings 6 +1 vibration load during a certain work period, it is also
Tool holder Hexagon tool holder with locking
important to consider the periods during which the device
mechanism is switched off, or is running but not actually employed.
Max. drilling diameter This can reduce the vibration load over the entire work
Wood 6 mm period significantly.
Metal 4 mm
Max. torque 4 Nm
Weight 380 g
Battery (integrated)
Type Li-ion
Nominal voltage 3.6 V
Capacity 1500 mAh
Charger PSCS 10-3.6V AC
Input
Nominal voltage 100 - 240 V ~ 50 - 60 Hz
Power input 8W
Output
Nominal voltage 5V
Charging current 600 mA
Charging time 3h
Protection class II /
Sound values according to EN 60745
Sound pressure level 63 dB(A)
Sound power level 74.1 dB(A)
Uncertainty K 3 dB(A)
Vibration information according to EN 60745
Vibration emission value drilling in 0.216 m/s2
metal / screwing ah=in
Uncertainty K 1.5 m/s2

7 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

Transport and storage Storage
Before storing the device, proceed as follows:
Note • Set the switch for clockwise / counter-clockwise rotation
If you store or transport the device improperly, the to centre position (lock).
device may be damaged. • Clean the device as described in the Maintenance chapter.
Note the information regarding transport and storage of
• For storing the device, use the transport case included in
the device.
the scope of delivery in order to protect the device from
Transport external influences.
For transporting the device, use the transport case included in • Do not store Li-ion batteries which are completely
the scope of delivery in order to protect the device from external discharged. Storing discharged batteries can lead to a
influences. deep discharge and thus damage the battery.
Before transporting the device, proceed as follows: When the device is not being used, observe the following
• Switch off the device by setting the switch for clockwise / storage conditions:
counter-clockwise rotation to centre position (lock). • dry and protected from frost and heat
• Allow the device to cool down. • ambient temperature below 40 °C
The supplied Li-ion batteries are subjects to the requirements of • protected from dust and direct sunlight inside the transport
dangerous goods legislation. case
Observe the following when transporting or shipping Li-ion
batteries:
• The user may transport the batteries by road without any
additional requirements.
• If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.
– Only ship batteries if their housing is undamaged.
– Please also observe any other national regulations.

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 8

Start-up 2. Insert the mains plug of the charger (11) into a properly
fused mains socket.
Unpacking the device ð Charging requires approx. 3 hours.
• Take the transport case out of the packaging.
Warning of electrical voltage
Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
• Check the contents of the transport case for completeness
and look for damages.
Warning!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
• Dispose of the packaging material according to the
national regulations.
Charging the battery
Caution!
While the battery is charging, the handle may become
slightly warm. This is normal. 3. Wait until the 3 LEDs of the battery level indication (3) are
illuminated.
Note ð The battery is fully charged.
The battery can be damaged in case of improper 4. Unplug the charger (11) from the mains socket.
charging. 5. Pull the barrel plug (14) out of the device.
Never charge the battery at ambient temperatures
below 10 °C or above 40 °C. ð The device and the charger (11) may have become
warm during charging.
The battery is partially charged upon delivery to avoid damage Allow the device to cool down to room temperature.
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red Info
LED in the battery level indication (3) is illuminated), the battery The device cannot be started when the charger is
should be charged. To do so, please proceed as follows: connected.
1. Insert the barrel plug (14) of the charger into the charger The on / off switch (12) can be pressed, but the motor
connection (7). will not start. The LED work lamp (13) and the battery
level indication (3) light up.
Checking the battery status
The battery status is displayed as follows by the three LEDs of
the battery level indication (3):

3h LED colour Meaning

Green – Orange – Red maximum charge / power
Orange – Red medium charge / power
7 Red weak charge – Recharge the battery.

14 1. Press the on / off switch (12).

ð You can read the battery status from the battery level
indication (3).

9 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

Changing tools Torque selection / drilling setting
The device is equipped with a tool holder with locking Using the torque selection, you can choose the desired, optimal
mechanism for hexagon (drill) bits. Please proceed as follows to torque setting.
remove or insert tools:
1. Set the switch for clockwise / counter-clockwise rotation (5)
to centre position (lock).
2. Pull the locking mechanism at the tool holder (1) back and
hold it in place.
3. If necessary, take the (drill) bit out of the tool holder (1).

• Select a low torque for smooth-running screws or soft

materials.
• Select a high torque for tight screws and hard materials as
well as for unscrewing.
• For drilling, select the drilling setting indicated by the
4. Insert the appropriate (drill) bit into the tool holder (1). symbol .

Info
5. Let go of the locking mechanism at the tool holder (1). When unscrewing, note the setting of the rotational
direction! On the clockwise / counter-clockwise
rotation direction indicator (5) you can see in which
direction the screws will be screwed.
Do not use the drilling setting for screwing!

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 10

Operation Selecting the rotational direction

Tips and notes on handling the cordless screwdriver Note

To avoid damaging the gear, only change the rotational
General information:
direction when the device is at a standstill.
• Check the tool in the bit holder for correct fit before every
application. The motor's rotational direction can be changed by means of
the switch for clockwise / counter-clockwise rotation (5).
• The centre position of the clockwise / counter-clockwise
1. Press in the switch for clockwise / counter-clockwise
rotation switch (lock) is suited for work breaks or (drill) bit
rotation (5) on the side to which the motor shall rotate.
exchange.
Screws: I. II.
• In case of soft wood, screws can be screwed in without
pre-drilling.
• In case of hard wood or large screws, it is recommended
to use a drill for pre-drilling. 5
• When using countersunk screws, the drill hole should be
countersunk beforehand.
• Especially smaller screws and bits may be damaged when
selecting an excessive torque and / or speed at the tool.
Drilling in general:
• Take short breaks regularly during drilling. When doing so,
I. Screwing in II. Unscrewing
take the drill bit out of the drill hole so that the drill bit can
cool down. 2. Carry out a short test run to see whether the rotational
• Secure the workpiece in a tensioning device or vice. direction matches the intended application. A wrong
• Use a suitable aid to mark the intended location of the drill rotational direction may damage the tool and / or
hole. workpiece.
Drilling in metal: 3. If required, set the switch for clockwise / counter-clockwise
• Use suitable metal drill bits (e.g. drill bits made of high- rotation (5) to centre position (lock) to block the on / off
speed steel (HSS)). switch (12).
• For larger drilling diameters, use a smaller drill bit for pre-
drilling.
• Metal drill bits may also be used for drilling in plastic.
Drilling in wood:
• Use drill bits suitable for wood.
• Place a block of wood under the workpiece or drill in from
both sides so that the wood cannot break off when it is
being drilled through.
• Use a wood drill bit with centring tip. For deep drill holes,
use an auger bit; for large drilling diameters, use a
Forstner bit.

11 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

Handle position Switching the device on and off
The handle position can be adjusted to either vertical or 1. Check whether the tool and the selected torque setting are
horizontal in order to reach poorly accessible locations more suitable for the intended application.
easily. 2. Check whether the workpiece is secured and the worktop
1. Set the switch for clockwise / counter-clockwise rotation (5) prepared correspondingly.
to centre position (lock). 3. Press and hold the on / off switch (12) during screwing or
2. Press and hold the handle position switch (4). drilling.
ð The device operates with the previously selected
4 12
settings.
ð The LED work lamp (13) is illuminated.

13

12

6
12

3. Carefully turn the handle (6) clockwise around the rotation

axis until it reaches the horizontal position and locks in
place. 4. Let go of the on / off switch (12) to stop the device.
4. Let go of the handle position switch (4). ð The LED work lamp (13) turns off.
4 12 6 Info
The motor has an integrated brake that quickly stops
the motor once you let go of the on / off switch (12).
Shutdown
1. Set the switch for clockwise / counter-clockwise rotation (5)
to centre position (lock).
2. If required, allow the device to cool down.
3. Remove the tool from the device (see Start-up chapter).
4. Clean the device according to the Maintenance chapter.
5. Store the device according to the Storage chapter.
5. Check whether the handle (6) is firmly seated in the new
position.
Info
When the handle is in horizontal position, the rotational
direction must be selected contrary to the description
in the chapter Selecting the rotational direction. Note
the direction of the arrow on the clockwise / counter-
clockwise rotation switch (5).

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 12

Available accessories The device does not start:
• The battery power might be too low. Recharge the battery.
Warning! • Check the position of the clockwise / counter-clockwise
Only use accessories and additional equipment rotation switch. The switch must be pressed in all the way.
specified in the operating manual. If the clockwise / counter-clockwise rotation switch is in
Using insertion tools or accessories other than those centre position (lock), the on / off switch is blocked.
specified in the operating manual may cause a risk of • Check whether the charger is connected. If the charger is
injury. connected, the device will not start.
Accessories Article number Info
Screw bit set, 32-piece 6.200.001.001
Wait for at least 10 minutes before switching the
device back on.
Errors and faults The drill bit does not penetrate / hardly penetrates the
The device has been checked for proper functioning several material:
times during production. If malfunctions occur nonetheless, • Check whether the correct torque setting is selected. The
check the device according to the following list. drilling setting should be selected.
Troubleshooting tasks which require the housing to be opened • Check whether the device is set to counter-clockwise
must only be carried out by a specialist dealer or by Trotec. rotation. For drilling, it is necessary to switch over to
Slight smoke or odour are emitted during first use: clockwise rotation.
• This is not a fault. These phenomena disappear after a • Check whether the characteristics of the material require
brief runtime. the use of a hammer drill or impact drill.
The battery does not charge: The on / off switch cannot be pressed:
• Check whether the device is correctly connected to the • Check whether the clockwise / counter-clockwise rotation
charger and whether the charger is correctly connected to switch is in centre position (lock). Set the desired rotational
the power supply. direction to unlock the tool.
• Check the power connection. Note
• Check the power cable and mains plug for damages. Wait for at least 3 minutes after maintenance and
• Check the fuse (home). repair work. Only then switch the device back on.
• Check the charger for damages. Should the charger be Your device still does not operate correctly after these
damaged, stop using it. Contact the Trotec customer checks?
service. Please contact the customer service. If necessary, bring the
• Check the charger connection for dirt. Remove any dirt. device to an authorized specialist electrical company or to
• The battery might be defective. Contact the Trotec Trotec for repair.
customer service.

13 Operating manual – cordless baton screwdriver PSCS 10-3,6V EN

Maintenance Disposal
Activities required before starting maintenance
Warning of electrical voltage In the European Union, electronic equipment must not be
Do not touch the mains plug or the battery with wet or treated as domestic waste, but must be disposed of
damp hands. professionally in accordance with Directive 2002/96/EC of the
• Switch off the device. European Parliament and of the Council of 27 January 2003 on
• Hold onto the mains plug while pulling the power cable out waste electrical and electronic equipment (WEEE). At the end of
of the mains socket. its life, please dispose of this device according to the valid legal
requirements.
• Allow the device to cool down completely.
Warning of electrical voltage
Li-Ion
Maintenance tasks which require the housing to be
opened must only be carried out by authorised In the European Union, batteries and accumulators must not be
specialist companies or by Trotec. treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
Notes on maintenance European Parliament and of the Council of 6 September 2006
Inside the device, there are no parts that need to be maintained on batteries and accumulators. Please dispose of batteries and
or lubricated by the user. accumulators according to the relevant legal requirements.
Cleaning
The device should be cleaned before and after each use.
Info
The device does not have to be lubricated after
cleaning.
Warning of electrical voltage
There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.
• Clean the device with a soft, damp and lint-free cloth.
Ensure that no moisture enters the housing. Protect
electrical components from moisture. Do not use any
aggressive cleaning agents such as cleaning sprays,
solvents, alcohol-based or abrasive cleaners to dampen
the cloth.
• Dry the device and the bits with a soft cloth, lint-free cloth.
• Remove any drilling dust and, if applicable, wood chips
from the tool holder.
• Keep the connecting terminals on the device and charger
clean.
• Keep the ventilation openings free from dust deposits to
prevent overheating of the motor.

EN Operating manual – cordless baton screwdriver PSCS 10-3,6V 14

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
[email protected]
www.trotec.com