DATASHEET

NI 9205
16 AI Differential/32 AI Single-Ended, ±200 mV to ±10 V, 16 Bit,
250 kS/s Aggregate

• DSUB or spring-terminal connectivity

• 250 Vrms, CAT II, channel-to-earth
isolation (spring terminal); 60 VDC,
CAT I, channel-to-earth isolation
(DSUB)

The NI 9205 is a C Series module for use with any CompactDAQ or CompactRIO system.
Each channel has programmable input ranges of ±200 mV, ±1 V, ±5 V, and ±10 V. To protect
against signal transients, the NI 9205 includes ±30 V of overvoltage protection between input
channels and common (COM). In addition, the NI 9205 also includes a channel-to-earth-
ground double isolation barrier for safety, noise immunity, and high common-mode voltage
range. The NI 9205 is rated for 1,000 Vrms transient overvoltage protection.
 • NI 9205
Kit Contents
• NI 9205 Getting Started Guide

Screw-Terminal
• NI 9940 Backshell Kit (779567-01)

DSUB
Accessories
Front-Mount
• NI 9923 Screw-Terminal Block (780179-01)
Cable
• DSUB Cable, 1 m (778621-01)

C SERIES ANALOG INPUT MODULE COMPARISON

Product Signal Sample

Channels Simultaneous Resolution Connectivity
Name Levels Rate
Screw-Terminal,
NI 9201 ±10 V 8 Single-Ended 500 kS/s No 12-Bit Spring-Terminal,
DSUB
±200 mV, ±1 V, 32 Single-Ended, Spring-Terminal,
NI 9205 250 kS/s No 16-Bit
±5 V, ±10 V 16 differential DSUB

±200 mV, ±1 V, 32 Single-Ended,

NI 9206 250 kS/s No 16-Bit Spring-Terminal
±5 V, ±10 V 16 Differential

NI 9207 ±10 V 8 Differential 500 S/s No 24-Bit DSUB

32 Single-Ended,
NI 9209 ±10 V 500 S/s No 24-Bit DSUB
16 Differential

Screw-Terminal,
NI 9215 ±10 V 4 Differential 100 kS/s/ch Yes 16-Bit Spring-Terminal,
BNC
Spring-Terminal,
NI 9220 ±10 V 16 Differential 100 kS/s/ch Yes 16-Bit
DSUB

Screw-Terminal,
NI 9221 ±60 V 8 Single-Ended 800 kS/s No 12-Bit Spring-Terminal,
DSUB
Screw-Terminal,
NI 9222 ±10 V 4 Differential 500 kS/s/ch Yes 16-Bit
BNC

Screw-Terminal,
NI 9223 ±10 V 4 Differential 1 MS/s/ch Yes 16-Bit
BNC

2 | ni.com | NI 9205 Datasheet

NI C Series Overview

NI provides more than 100 C Series modules for measurement, control, and communication
applications. C Series modules can connect to any sensor or bus and allow for high-accuracy
measurements that meet the demands of advanced data acquisition and control applications.
• Measurement-specific signal conditioning that connects to an array of sensors and signals
• Isolation options such as bank-to-bank, channel-to-channel, and channel-to-earth ground
• -40 °C to 70 °C temperature range to meet a variety of application and environmental
needs
• Hot-swappable
The majority of C Series modules are supported in both CompactRIO and CompactDAQ
platforms and you can move modules from one platform to the other with no modification.

CompactRIO
CompactRIO combines an open-embedded architecture
with small size, extreme ruggedness, and C Series
modules in a platform powered by the NI LabVIEW
reconfigurable I/O (RIO) architecture. Each system
contains an FPGA for custom timing, triggering, and
processing with a wide array of available modular I/O to
meet any embedded application requirement.

CompactDAQ
CompactDAQ is a portable, rugged data acquisition platform
that integrates connectivity, data acquisition, and signal
conditioning into modular I/O for directly interfacing to any
sensor or signal. Using CompactDAQ with LabVIEW, you
can easily customize how you acquire, analyze, visualize,
and manage your measurement data.

NI 9205 Datasheet | © National Instruments | 3

Software
LabVIEW Professional Development System for Windows

• Use advanced software tools for large project development

• Generate code automatically using DAQ Assistant and Instrument
I/O Assistant
• Use advanced measurement analysis and digital signal processing
• Take advantage of open connectivity with DLLs, ActiveX,
and .NET objects
• Build DLLs, executables, and MSI installers

NI LabVIEW FPGA Module

• Design FPGA applications for NI RIO hardware

• Program with the same graphical environment used for desktop and
real-time applications
• Execute control algorithms with loop rates up to 300 MHz
• Implement custom timing and triggering logic, digital protocols, and
DSP algorithms
• Incorporate existing HDL code and third-party IP including Xilinx IP
generator functions
• Purchase as part of the LabVIEW Embedded Control and Monitoring
Suite

NI LabVIEW Real-Time Module

• Design deterministic real-time applications with LabVIEW

graphical programming
• Download to dedicated NI or third-party hardware for reliable
execution and a wide selection of I/O
• Take advantage of built-in PID control, signal processing, and
analysis functions
• Automatically take advantage of multicore CPUs or set
processor affinity manually
• Take advantage of real-time OS, development and debugging
support, and board support
• Purchase individually or as part of a LabVIEW suite

Input Circuitry
The NI 9205 channels share a common ground that is isolated from other modules in the
system. All channels share a programmable gain instrumentation amplifier and are multiplexed
to an ADC. Each channel also has ±30 V overvoltage protection.

4 | ni.com | NI 9205 Datasheet

 Figure 1. Input Circuitry for One Analog Input Channel on the NI 9205

Trig
AI+ Trigger

AI– MUX PGIA ADC

AISENSE 16-bit
Filtered Isolated
COM Differential ADC
Amplifier
NI 9205

NI 9205 Specifications
The following specifications are typical for the range -40 °C to 70 °C unless otherwise noted.
All voltages are relative to COM unless otherwise noted.

Caution Do not operate the NI 9205 in a manner not specified in this document.
Product misuse can result in a hazard. You can compromise the safety protection
built into the product if the product is damaged in any way. If the product is
damaged, return it to NI for repair.

MTBF 775,832 hours at 25 °C; Bellcore Issue 6,

Method 1, Case 3, Limited Part Stress Method

Analog Input Characteristics

Number of channels 16 differential/32 single-ended channels
ADC resolution 16 bits
DNL No missing codes guaranteed
Conversion time (maximum sampling rate)
CompactRIO & CompactDAQ chassis 4.00 μs (250 kS/s)
R Series Expansion chassis 4.50 μs (222 kS/s)
Input coupling DC
Nominal input ranges ±10 V, ±5 V, ±1 V, ±0.2 V
Minimum overrange, ±10 V range 4%
Maximum working voltage for analog inputs Each channel must remain within ±10.4 V of
(signal + common mode) COM
Input impedance (AI-to-COM)
Powered on >10 GΩ in parallel with 100 pF
Powered off/overload 4.7 kΩ minimum
Input bias current ±100 pA

NI 9205 Datasheet | © National Instruments | 5

Crosstalk, at 100 kHz
Adjacent channels -65 dB
Non-adjacent channels -70 dB
Analog bandwidth 370 kHz
Overvoltage protection
AI channel, 0 to 31 ±30 V, one channel only
AISENSE ±30 V
Settling time for multichannel measurements, accuracy, all ranges
±120 ppm of full-scale step, ±8 LSB 4 μs convert interval
±30 ppm of full-scale step, ±2 LSB 8 μs convert interval
Analog triggers
Number of triggers 1
Resolution 10 bits, 1 in 1,024
Bandwidth, -3 dB 370 kHz
Accuracy ±1% of full scale
Scaling coefficients
±10 V range 328 μV/LSB
±5 V range 164.2 μV/LSB
±1 V range 32.8 μV/LSB
±0.2 V range 6.57 μV/LSB
CMRR, DC to 60 Hz 100 dB

Figure 2. CMRR, AI+ to AI-

AI <0...31> CMRR
140

120

100
CMRR (dB)

80

60

40

60 100 1k 10 k 100 k
Frequency (Hz)

6 | ni.com | NI 9205 Datasheet

Analog Input Absolute Accuracy
The following values are based on calibrated scaling coefficients, which are stored in the
onboard EEPROM.

Absolute accuracy
±10 V range
Accuracy at full scale1 6,230 μV
Random noise, σ 240 μVrms
Sensitivity2 96.0 μV
±5 V range
Accuracy at full scale1 3,230 μV
Random noise, σ 116 μVrms
Sensitivity2 46.4 μV
±1 V range
Accuracy at full scale1 690 μV
Random noise, σ 26 μVrms
Sensitivity2 10.4 μV
±0.2 V range
Accuracy at full scale1 174 μV
Random noise, σ 10 μVrms
Sensitivity2 4.0 μV
Residual gain error
±10 V range 115 ppm of reading
±5 V range 135 ppm of reading
±1 V range 155 ppm of reading
±0.2 V range 215 ppm of reading
Gain tempco 11 ppm/°C
Reference tempco 5

1 Absolute accuracy values at full scale on the analog input channels assume the device is operating
within 70 °C of the last external calibration and are valid for averaging 100 samples immediately
following self-calibration.
2 Sensitivity is a function of noise and indicates the smallest voltage change that can be detected.

NI 9205 Datasheet | © National Instruments | 7

Residual offset error
±10 V range 20 ppm of range
±5 V range 20 ppm of range
±1 V range 25 ppm of range
±0.2 V range 40 ppm of range
Offset tempco
±10 V range 44 ppm of range/°C
±5 V range 47 ppm of range/°C
±1 V range 66 ppm of range/°C
±0.2 V range 162 ppm of range/°C
INL error 76 ppm of range

Analog Input Accuracy Formulas

Absolute Accuracy = Reading * Gain Error + Range * Offset Error + Noise Uncertainty
where
Gain Error = Residual Gain Error + Gain Tempco * Temp Change from Last Internal Cal
+ Reference Tempco * Temp Change from Last External Cal
Offset Error = Residual Offset Error + Offset Tempco * Temp Change from Last Internal
Cal + INL Error
Noise Uncertainty = (Random Noise * 3) / √100 for a coverage factor of 3 σ and
averaging 100 points

Absolute accuracy at full scale on the analog input channels is determined using the following
assumptions:
Temp Change from Last External Cal = 70 °C
Temp Change from Last Internal Cal = 1 °C
Number of Readings = 100
Coverage Factor = 3 σ

For example, on the ±10 V range, the absolute accuracy at full scale is as follows:
Gain Error = 115 ppm + 11 ppm * 1 + 5 ppm * 70
Gain Error = 476 ppm
Offset Error = 20 ppm + 44 ppm * 1 + 76 ppm
Offset Error = 140 ppm
Noise Uncertainty = (240 μV * 3) / √100
Noise Uncertainty = 72 μV
Absolute Accuracy = 10 V * 476 ppm + 10 V * 140 ppm + 72 μV
Absolute Accuracy = 6,232 μV, rounds to 6,230 μV

8 | ni.com | NI 9205 Datasheet

Digital Characteristics
Number of channels 1 digital input channel, 1 digital output
channel3
Overvoltage protection ±30 V
Digital logic levels
Input high, VIH
Minimum 2.0 V
Maximum 3.3 V
Input low, VIL
Minimum 0V
Maximum 0.34 V
Output high, VOH, sourcing 75 μA
Minimum 2.1 V
Maximum 3.3 V
Output low, VOH, sinking 250 μA
Minimum 0V
Maximum 0.4 V
External digital triggers
Source PFI0
Delay 100 ns maximum

Power Requirements
Power consumption from chassis
Active mode 625 mW maximum
Sleep mode 15 mW
Thermal dissipation (at 70 °C)
Active mode 625 mW maximum
Sleep mode 15 mW

3 The digital input and digital output channel are supported only in FPGA Interface mode in
software.

NI 9205 Datasheet | © National Instruments | 9

Physical Characteristics
If you need to clean the module, wipe it with a dry towel.

Tip For two-dimensional drawings and three-dimensional models of the C Series

module and connectors, visit ni.com/dimensions and search by module number.

Spring-terminal wiring
Gauge 0.8 mm2 to 1.0 mm2 (28 AWG to 18 AWG)
copper conductor wire
Wire strip length 7 mm (0.276 in.) of insulation stripped from
the end
Temperature rating 90 °C minimum
Wires per spring terminal One wire per spring terminal
Connector securement
Securement type Screw flanges provided
Torque for screw flanges 0.2 N · m (1.80 lb · in.)
Weight
NI 9205 with spring terminal 158 g (5.8 oz)
NI 9205 with DSUB 148 g (5.3 oz)

Safety Voltages
Connect only voltages that are within the following limits:

Maximum voltage4
Channel-to-COM ±30 VDC

NI 9205 with Spring Terminal Isolation Voltages

Channel-to-channel None
Channel-to-earth ground5
Continuous 250 Vrms, Measurement Category II
Withstand 2,300 Vrms, verified by a 5 s dielectric
withstand test

Measurement Category II is for measurements performed on circuits directly connected to the

electrical distribution system. This category refers to local-level electrical distribution, such as
that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe.

4 The maximum voltage that can be applied or output between AI and COM without creating a safety
hazard.
5 This specification is valid only up to 2,000 m.

10 | ni.com | NI 9205 Datasheet

 Caution Do not connect the NI 9205 to signals or use for measurements within
Measurement Categories III or IV.

NI 9205 with DSUB Isolation Voltages

Channel-to-channel None
Channel-to-earth ground
Continuous 60 VDC, Measurement Category I
Withstand
up to 2,000 m 1,000 Vrms, verified by a 5 s dielectric
withstand test
up to 5,000 m 500 Vrms, verified by a 5 s dielectric
withstand test

Measurement Category I is for measurements performed on circuits not directly connected to

the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This category is for measurements of voltages
from specially protected secondary circuits. Such voltage measurements include signal levels,
special equipment, limited-energy parts of equipment, circuits powered by regulated low-
voltage sources, and electronics.

Caution Do not connect the NI 9205 to signals or use for measurements within
Measurement Categories II, III, or IV.

Hazardous Locations
U.S. (UL) Class I, Division 2, Groups A, B, C, D, T4;
Class I, Zone 2, AEx nA IIC T4
Canada (C-UL) Class I, Division 2, Groups A, B, C, D, T4;
Class I, Zone 2, Ex nA IIC T4
Europe (ATEX) and International (IECEx) Ex nA IIC T4 Gc

Safety and Hazardous Locations Standards

This product is designed to meet the requirements of the following electrical equipment safety
standards for measurement, control, and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
• EN 60079-0:2012, EN 60079-15:2010
• IEC 60079-0: Ed 6, IEC 60079-15; Ed 4

NI 9205 Datasheet | © National Instruments | 11

• UL 60079-0; Ed 5, UL 60079-15; Ed 3
• CSA 60079-0:2011, CSA 60079-15:2012

Note For UL and other safety certifications, refer to the product label or the Online
Product Certification section.

Electromagnetic Compatibility
This product is designed to meet the requirements of the following standards of EMC for
electrical equipment for measurement, control, and laboratory use:
• EN 61326 EMC requirements; Industrial Immunity
• EN 55011 Emissions; Group 1, Class A
• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
Note For EMC compliance, operate this device with shielded cabling.

CE Compliance
This product meets the essential requirements of applicable European Directives, as follows:
• 2014/35/EU; Low-Voltage Directive (safety)
• 2014/30/EU; Electromagnetic Compatibility Directive (EMC)
• 94/9/EC; Potentially Explosive Atmospheres (ATEX)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance
information. To obtain product certifications and the DoC for this product, visit ni.com/
certification, search by model number or product line, and click the appropriate link in the
Certification column.

Shock and Vibration

To meet these specifications, you must panel mount the system.

Operating vibration
Random (IEC 60068-2-64) 5 grms, 10 Hz to 500 Hz
Sinusoidal (IEC 60068-2-6) 5 g, 10 Hz to 500 Hz
Operating shock (IEC 60068-2-27) 30 g, 11 ms half sine; 50 g, 3 ms half sine;
18 shocks at 6 orientations

12 | ni.com | NI 9205 Datasheet

Environmental
Refer to the manual for the chassis you are using for more information about meeting these
specifications.

Operating temperature -40 °C to 70 °C

(IEC 60068-2-1, IEC 60068-2-2)
Storage temperature -40 °C to 85 °C
(IEC 60068-2-1, IEC 60068-2-2)
Ingress protection IP40
Operating humidity (IEC 60068-2-78) 10% RH to 90% RH, noncondensing
Storage humidity (IEC 60068-2-78) 5% RH to 95% RH, noncondensing
Pollution Degree 2
Maximum altitude 5,000 m

Indoor use only.

Environmental Management
NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.
For additional environmental information, refer to the Minimize Our Environmental Impact
web page at ni.com/environment. This page contains the environmental regulations and
directives with which NI complies, as well as other environmental information not included in
this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all NI products must be
disposed of according to local laws and regulations. For more information about
how to recycle NI products in your region, visit ni.com/environment/weee.

电子信息产品污染控制管理办法（中国 RoHS）
中国客户 National Instruments 符合中国电子信息产品中限制使用某些有害物
质指令(RoHS)。关于 National Instruments 中国 RoHS 合规性信息，请登录
ni.com/environment/rohs_china。(For information about China RoHS
compliance, go to ni.com/environment/rohs_china.)

NI 9205 Datasheet | © National Instruments | 13

Calibration
You can obtain the calibration certificate and information about calibration services for the
NI 9205 at ni.com/calibration.
Calibration interval 2 years

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and
company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI
products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the
National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs)
and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/
legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other
import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION
CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data contained in
this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth
in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

© 2015 National Instruments. All rights reserved.

374188A-02 Oct15