CMP PRODUCTS CABLE GLAND CATALOGUE

E
F
CMP EXPLOSIVE ATMOSPHERES PRODUCTS

D B C
A

TECHNICAL DATA
Design Specification BS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classification* Impact = Level 8, Cable Anchorage = Class D

T3CDS
Enclosure Protection IK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classification* Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX Certificate SIRA13ATEX1073X, SIRA13ATEX4079X
^ II 2G,II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da,
Triton CDS (T3CDS) Globally Approved, Code of Protection
^ II 3G Ex nR IIC Gc, ^ I M2, Ex d I Mb, Ex e I Mb
Explosive Atmosphere Cable Gland Compliance Standards EN60079-0,1,7,15,31
IECEx Certificate IECEx SIR 13.0028X, IECEx SIM 14.0007X
Code of Protection Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
For all types of Armoured Cables
Compliance Standards IEC 60079-0,1,7,15,31
cCSAus Certificate (20S16 - 90) 1310517
• Fully sequential, three step installation procedure
Class I, Div 2, Groups A,B,C and D, Class II, Div 2, Groups E,F and G, Class III, Enclosure
• Reduces installation times, cost & risk CSAus Code of Protection Type 3, 4 and 4X,
Class I, Zone 1, AEx e II, AEx nR II
• Direct & remote installation Class I, Div 2, Groups A,B,C and D, Class II, Div 2, Groups E,F and G, Class III, Enclosure
cCSA Code of Protection Type 3, 4 and 4X,
• Unique compensating displacement seal system (CDS) Ex d IIC, Ex e IIC, Ex nR II
• Metal-to-metal installation every time regardless of cable diameter CAN/CSA-C22.2 No 0, 18, 25, 30, 94, 174, CAN/CSA-E60079-0, 1, 7,
Compliance Standards
ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079-0, 1, 7
• Designed to reduce the effects of Coldflow UL Certificate (20S16 - 90) E200163
• Integral protected deluge seal Code of Protection Class I, Zone 1, AEx e II
Compliance Standards UL514B
• Controlled outer ‘load retention’ seal
• Unique OSTG prevents overtightening EAC Certificate TC RU C-GBȽȻ%

• -60˚C to +130˚C (standard), -20˚C to 200˚C (ThermEx option) UkrSEPRO UA.TR.047.C.0644-15

NEPSI Certificate GYJ13.1141X / GYJ13.1283X
• Globally marked, IECEx, ATEX, UL & cCSAus
CCOE / PESO (India) Certificate P333688
• Superior EMC performance INMETRO Certificate TUV 11.0374X
RETIE Certificate 03866
Marine Certificates LRS: 01/00172 (E3), DNV: E-13848, ABS: 14-LD234401A-4-PDA, BV: 43180/A1
Ingress Protection Rating** IP66, IP67 & IP68***
Deluge Protection Compliance DTS01 : 91
Cable Gland Material Brass, Electroless Nickel Plated Brass, Aluminium, Stainless Steel
Seal Material CMP SOLO LSF Halogen Free Thermoset Elastomer
† Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour
(STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA), Single Wire Armour (SWA), Aluminium Wire Armour (AWA), Pliable Wire Armour (PWA),
Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the
Stepped Cone (W). Cable Type(s) Steel Tape Armour (STA), Aluminium Strip Armour (ASA), Screened Flexible (EMC) Wire
Braid (e.g CY/SY), Wire Braid Armour (e.g SWB)
Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a double wire
strand of braid armour cables. Tapes can also be doubled over. For cables that have only a single layer of Armour Clamping Reversible Armour Cone & AnyWay Universal Clamping Ring
armour such as SWA the clamping range should be used as shown in the table below.
Inner Bedding Sealing Ring: Compensating Displacement Seal (CDS), Outer Sheath
Sealing Technique
Stepped (W) Cone is suitable for Single Wire Armour (SWA), or Aluminium Wire Armour (AWA) cables. Sealing Ring : Load Retention Seal (LRS)
Sealing Area(s) Cable Inner Bedding & Outer Cable Sheath
* Mechanical & Electrical Classifications applied as per IEC 62444 & EN 62444
** When CMP installation accessories are used. Refer to page 7 or www.cmp-products.com for further information.
*** IP68 tested to a minimum depth of 30 metres for 12 hours, alternate depths / durations can be provided upon request
Cable Gland Selection Table Dimensions listed below are for metric cable glands only
Refer to illustration at the top of the page. Dimensions for alternative threads may vary, please see supplementary technical data sheet
Available Entry Threads “C” Cable Overall Armour Range † Across Across Combined Ordering
(Alternate Metric Thread Lengths Available) Bedding Cable
Grooved Stepped Flats Corners Reference Cable
Cable Diameter Diameter Protrusion
Standard Option Cone (X) Cone (W) “D” “D” (*Brass Metric) Gland
Gland “A” “B” Length Shroud
Weight
Size Thread “F”
Thread Length Ordering (Kgs)
Metric NPT Length (NPT) NPT Min Max Min Max Min Max Min Max Max Max Size Type
(Metric) “E” Suffix
“E”
16 M16 15.0 - - - 3.1 8.6 6.1 13.1 0.3 1.0 0.8 1.25 24.0 26.4 78.7 16 T3CDS 1RA PVC36 0.18
20S16 M20 15.0 ½” 19.9 ¾" 3.1 8.6 6.1 13.1 0.3 1.0 0.8 1.25 24.0 26.4 78.7 20S16 T3CDS 1RA PVC36 0.20
20S M20 15.0 ½” 19.9 ¾" 6.1 11.6 9.5 15.9 0.3 1.0 0.8 1.25 24.0 26.4 78.7 20S T3CDS 1RA PVC36 0.20
20 M20 15.0 ½” 19.9 ¾" 6.5 13.9 12.5 20.9 0.4 1.0 0.8 1.25 30.5 33.6 76.2 20 T3CDS 1RA PVC06 0.28
25S M25 15.0 ¾” 20.2 1" 11.1 19.9 14.0 22.0 0.4 1.2 1.25 1.6 37.5 41.3 88.8 25S T3CDS 1RA PVC09 0.44
25 M25 15.0 ¾” 20.2 1" 11.1 19.9 18.2 26.2 0.4 1.2 1.25 1.6 37.5 41.3 88.7 25 T3CDS 1RA PVC09 0.44
32 M32 15.0 1” 25.0 1 ¼" 17.0 26.2 23.7 33.9 0.4 1.2 1.6 2.0 46.0 50.6 90.7 32 T3CDS 1RA PVC11 0.63
40 M40 15.0 1 ¼” 25.6 1 ½" 22.0 32.1 27.9 40.4 0.4 1.6 1.6 2.0 55.0 60.5 93.2 40 T3CDS 1RA PVC15 0.91
50S M50 15.0 1 ½” 26.1 2" 29.5 38.1 35.2 46.7 0.4 1.6 2.0 2.5 60.0 66.0 100.7 50S T3CDS 1RA PVC18 1.12
50 M50 15.0 2” 26.9 2 ½" 35.6 44.0 40.4 53.0 0.6 1.6 2.0 2.5 70.1 77.1 105.8 50 T3CDS 1RA PVC21 1.60
63S M63 15.0 2” 26.9 2 ½" 40.1 49.9 45.6 59.4 0.6 1.6 2.0 2.5 75.0 82.5 102.5 63S T3CDS 1RA PVC23 1.73
63 M63 15.0 2 ½” 39.9 3" 47.2 55.9 54.6 65.8 0.6 1.6 2.0 2.5 80.0 88.0 105.4 63 T3CDS 1RA PVC25 1.78
75S M75 15.0 2 ½” 39.9 3" 52.8 61.9 59.0 72.0 0.6 1.6 2.0 2.5 90.0 99.0 110.6 75S T3CDS 1RA PVC28 2.57
75 M75 15.0 3” 41.5 3 ½" 59.1 67.9 66.7 78.4 0.6 1.6 2.5 3.0 100.0 110.0 120.3 75 T3CDS 1RA PVC30 3.33
90 M90 24.0 3 ½” 42.8 4" 66.6 78.6 76.2 90.3 0.8 1.6 3.15 4.0 115.0 126.5 138.9 90 T3CDS 1RA PVC32 4.87
100 M100 24.0 3 ½” 42.8 4" 76.0 90.9 86.1 101.4 0.8 1.6 3.15 4.0 127.0 139.7 128.2 100 T3CDS 1RA LSF33 4.97
115 M115 24.0 4" 44.0 5" 86.0 97.9 101.5 110.2 0.8 1.6 3.15 4.0 138.0 151.8 161.3 115 T3CDS 1RA LSF34 7.72
130 M130 24.0 5" 46.8 - 97.0 114.9 110.2 123.2 0.8 1.6 3.15 4.0 157.0 172.7 173.3 130 T3CDS 1RA LSF35 9.78
*For material options add the following suffix to the Ordering Reference; Brass (no suffix required); Nickel Plated Brass ‘5’; 316 Grade Stainless Steel ‘4’; Copper Free Aluminium ‘1’
For NPT options add the following digits to the material suffix; ½” = 31; ¾” = 32; 1” = 33; 1 ¼” = 34; 1 ½” = 35; 2” = 36; 2 ½” = 37; 3” = 38; 3 ½” = 39; 4” = 310 (Brass requires prefix ‘0’)
Examples: 32T3CDS1RA534 = Nickel Plated Brass 1¼” NPT, 50ST3CDS1RA035 = Brass 1½” NPT, 25T3CDS1RA432 = Stainless Steel ¾” NPT, 20T3CDS1RA5 = Nickel Plated Brass M20
Dimensions are displayed in millimetres unless otherwise stated

56 www.cmp-products.com