Scribd Logo
Upload

Welcome to Scribd!

  • 66 views

    Arcadiator Build Doc v1B Updated

    Uploaded by

    Edward Jones
    The document provides a bill of materials for building the Arcadiator effect pedal. It lists the required capacitors, resistors, integrated circuits, switches, pots, and diodes. It also provides some Arcadiator-specific build info, noting that the LFO LED can be switched or always on, the threshold trimmer sets the LFO trigger, and many switches and pots require careful placement in the enclosure before soldering.

    Copyright:

    © All Rights Reserved
    Download as ODG, PDF, TXT or read online from Scribd

    Arcadiator Build Doc v1B Updated

    Uploaded by

    Edward Jones
    66 views1 page
    The document provides a bill of materials for building the Arcadiator effect pedal. It lists the required capacitors, resistors, integrated circuits, switches, pots, and diodes. It also provides some Arcadiator-specific build info, noting that the LFO LED can be switched or always on, the threshold trimmer sets the LFO trigger, and many switches and pots require careful placement in the enclosure before soldering.

    Original Description:

    Arcadiator Build Doc v1B updated

    Original Title

    Arcadiator Build Doc v1B updated

    Copyright

    © © All Rights Reserved

    Available Formats

    ODG, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides a bill of materials for building the Arcadiator effect pedal. It lists the required capacitors, resistors, integrated circuits, switches, pots, and diodes. It also provides some Arcadiator-specific build info, noting that the LFO LED can be switched or always on, the threshold trimmer sets the LFO trigger, and many switches and pots require careful placement in the enclosure before soldering.

    Copyright:

    © All Rights Reserved
    Download as ODG, PDF, TXT or read online from Scribd
    Download as odg, pdf, or txt
    66 views1 page

    Arcadiator Build Doc v1B Updated

    Uploaded by

    Edward Jones
    The document provides a bill of materials for building the Arcadiator effect pedal. It lists the required capacitors, resistors, integrated circuits, switches, pots, and diodes. It also provides some Arcadiator-specific build info, noting that the LFO LED can be switched or always on, the threshold trimmer sets the LFO trigger, and many switches and pots require careful placement in the enclosure before soldering.

    Copyright:

    © All Rights Reserved
    Download as ODG, PDF, TXT or read online from Scribd
    Download as odg, pdf, or txt
    of 1

    Arcadiator BOM

    Capacitors Resistors IC
    C1 100n R1 1M IC1 CD4069
    C2 2n2 R2 1M IC2 CD4024
    C3 2u2 R3 10k IC3 CD4070
    C4 1uF R4 1M Switch
    C5 1uF R5 10k LFO_SW SPDT
    C6 10nF R6 27k MODE_SW SPDT
    C7 100nF R7 5k-10k CLR PWM/OctUP SPDT
    Diodes R8 100k OCT_SW DPDT
    D1-D4 1n4148 R9 100k Pots
    D5 1n5817 R10 100k RATE 200kB
    R11 10k VOLUME 100kA
    R12 100k BLEND 500kB
    R13 100k PWM/OCT_UP 500kC
    R14 100k THRESH 100k trim
    R15 10k
    R16 47k
    R17 100k
    R18 100k
    R19 100k

    Arcadiator-Specific Build Info:


    to light all the time, put a drop of solder on this. If you would rather have the LFO
    LED on only when engaged, solder a wire from the pad named “TO_SW” to a switched
    ground on your stomp. You can mount the LED right from the PCB if you wish by
    using the drill template.
     The threshold trimmer is used to set the trigger for the LFO threshold
     There are a LOT of switches and pots on this PCB. Be sure to place them in the PCB
    without soldering first, THEN place them in your drilled enclosure. Gently tighten the
    nuts to the enclosure, then solder LAST. Otherwise, it will be really hard to get this in
    an enclosure. This PCB is designed for mounting in a 1590BB in the vertical
    orientation.

    Arcadiator – Fuzz- v1B – Build Document Page 2 of 6

    You might also like