Top 15 Mechanical Testing - Cswip 3.1 Course Questions and Answers

6/3/2020 TOP 15 MECHANICAL TESTING - CSWIP 3.
1 COURSE QUESTIONS AND ANSWERS
Welding Search Engine
TOP 15 MECHANICAL TESTING – CSWIP 3.1 COURSE

QUESTIONS AND ANSWERS
Weldingsearchengine 2 years ago
TOP 15 MECHANICAL TESTING - CSWIP 3.1 COURSE QUESTIONS AND ANSWERS
TOP 15 MECHANICAL TESTING – CSWIP 3.1 COURSE

QUESTIONS AND ANSWERS
Here you can follow Top 15 Mechanical Testing – Cswip
3.1 Course Questions And Answers:
1. Q: – What unit of measurement is used for chirpy impact testing?
1. Joules =-O
2. Nmm2
3. KJ/mm
4. VPN
https://www.weldingsearchengine.com/top-15-mechanical-testing/amp/ 1/5
6/3/2020 TOP 15 MECHANICAL TESTING - CSWIP 3.1 COURSE QUESTIONS AND ANSWERS
2. Q: – During a transverse tensile test, the rst stage the specimen goes
through is known?
1. Plastic stage
2. Elastic stage =-O
3. Deformed stage
4. UTS stage
3. Q: – Which one of these tests would most probably be used for welder
quali cation on a plate butt weld using 13mm low carbon steel?
1. E ective for revealing any lack of sidewall fusion

2. Nick break test =-O
3. Fracture llet test
4. IZOD
4. Q: – Which one of these tests is classed as qualitative?
1. Hardness test
2. Tensile
3. Macro test =-O
4. Toughness tests
5. Q: – A transverse tensile test was carried out on a welding procedure.

The cross-sectional area of the specimen was 30 mm wide and 15 mm
thick. The maximum load applied was 170 KN. What is the ultimate
tensile strength value?
1. 377N/mm2 =-O
2. 450 N/mm2
3. 300N/mm2
4. 600N/mm2
6. Q: – The same tensile test was 120 mm long before testing and after
testing the length was 135 mm long. What is the percentage of
elongation?
1. 20%
2. 15%
3. 11%
4. 5% =-O
7. Q: – In a welding procedure transverse joint tensile test the following

observations were made. The specimen CSA was recorded as 30 mm X
20mmand the maximum load applied was recorded as 200KN .what is
the UTS?
1. 33kN/mm2
2. 333N/mm2
3. 3333N/mm2
4. 33N/mm2
8. Q: – Chirpy impact tests showing a rough torn surface after the

completed test would indicate which type of failure?
1. Fatigue
2. Ductile
3. Fatigue to ductile
4. Brittle
9. Q: – Which of the following is NOT a quantitative test?
1. Root bend
2. Macro hardness
3. Chirpy
4. Tensile
10. Q: – When transverse tensile testy ng a welded joint excess weld

metal is often removed. This action is done to:
1. Allow the test piece to t accurately into the equipment

2. Reduce stress concentrations to the weld toes
3. Allow strain gauges to be placed over the weld face area
4. Allow weld metal ductility to be measured.
11. Q:- In an all weld tensile test, the original specimen gauge length was
50 mm and after the test, the increased gauge length was 65 mm. What is
the elongation percentage?
1. % A is 40
2. % A is 60
3. % A is 30
4. % A is 36
12. Q: – In welder quali cation testing of 10 mm plates,2 root and 2 face

bends were tested .1 root bend failed what course of action would you
follow?
1. Accept them as 75% were acceptable, you are allowed one failure
2. 2 more root bends should be prepared and tested
3. 2 more root and 2 more face bends should be prepared and tested
4. Retest the welder.
13. Q: – An STRA test is carried out to determine which of the following?
1. A quick indication of the weld quality for welder quali cation tests
2. The test results can be used to verify that the material has not been adversely
mechanically damaged by the heat during welding
3. An indication of the material’s elongation properties.
4. An indication of the through-thickness ductility (in the Z direction)
14. Q: – Chirpy impact test shows a 50% rough torn surface and a 50%
at crystalline surface after the completed test, this would indicate
which type of failure.
1. Fatigue and brittle

2. Ductile and brittle
3. Ductile with gross yielding
4. Fatigue and ductile
15. Q: – Which of the following defects are unlikely to be detected by

normal radiographic techniques?
1. Intergranular corrosion cracking

2. Porosity
3. Slag
4. Lack of penetration
Click Here see latest CSWIP 3.1 Training Course Questions and Answers
If you want to Get Welding jobs in Your area than you can register here
If you want to hire welding professional you can feel free to post your requirements
here
Categories: CSWIP 3.1 Course Questions and Answers
Tags: astm standards for tensile testing of steel, cswip 3.1 course notes, cswip 3.1 exam pattern, cswip 3.1
macro test questions, cswip 3.1 practical exam pdf, cswip 3.1 question and answer 2018 model, cswip 3.1
questions and answers pdf 2018, cswip 3.2 questions and answers pdf, mechanical testing of materials pdf,
shimadzu universal testing machine manual, steel testing standards, tensile test pdf, tensile test specimen
dimensions astm, tensile test specimen dimensions iso, tensile test specimen specifications, TOP 15
MECHANICAL TESTING, welding inspector questions and answers
Welding Search Engine

Powered by WordPress Back to top

Top 15 Mechanical Testing - Cswip 3.1 Course Questions and Answers

Uploaded by

Copyright:

Available Formats

Top 15 Mechanical Testing - Cswip 3.1 Course Questions and Answers

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Top 15 Mechanical Testing - Cswip 3.1 Course Questions and Answers

Uploaded by

Copyright:

Available Formats

6/3/2020 TOP 15 MECHANICAL TESTING - CSWIP 3.

1 COURSE QUESTIONS AND ANSWERS

Welding Search Engine

TOP 15 MECHANICAL TESTING – CSWIP 3.1 COURSE

TOP 15 MECHANICAL TESTING - CSWIP 3.1 COURSE QUESTIONS AND ANSWERS

TOP 15 MECHANICAL TESTING – CSWIP 3.1 COURSE

1. E ective for revealing any lack of sidewall fusion

4. Q: – Which one of these tests is classed as qualitative?

5. Q: – A transverse tensile test was carried out on a welding procedure.

7. Q: – In a welding procedure transverse joint tensile test the following

8. Q: – Chirpy impact tests showing a rough torn surface after the

9. Q: – Which of the following is NOT a quantitative test?

10. Q: – When transverse tensile testy ng a welded joint excess weld

1. Allow the test piece to t accurately into the equipment

12. Q: – In welder quali cation testing of 10 mm plates,2 root and 2 face

13. Q: – An STRA test is carried out to determine which of the following?

1. Fatigue and brittle

15. Q: – Which of the following defects are unlikely to be detected by

1. Intergranular corrosion cracking

Categories: CSWIP 3.1 Course Questions and Answers

Welding Search Engine

You might also like