Scribd Logo
Upload

Welcome to Scribd!

  • 45 views

    Octopre Le Optional Codec Installation Guide: Top Cover Removal

    Uploaded by

    taatu
    The 3 sentence summary is: This document provides installation instructions for an optional digital codec card, including unpacking the kit contents, connecting cables between the codec card and main circuit board, securing the codec card with screws and nuts, and replacing covers when complete. Key steps include locating fixing holes, connecting ribbon and link cables observing polarity, and securing BNC connectors before testing the installed digital option.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Octopre Le Optional Codec Installation Guide: Top Cover Removal

    Uploaded by

    taatu
    45 views1 page
    The 3 sentence summary is: This document provides installation instructions for an optional digital codec card, including unpacking the kit contents, connecting cables between the codec card and main circuit board, securing the codec card with screws and nuts, and replacing covers when complete. Key steps include locating fixing holes, connecting ribbon and link cables observing polarity, and securing BNC connectors before testing the installed digital option.

    Original Description:

    octop

    Original Title

    octopreleoptionalcodecinstall1

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The 3 sentence summary is: This document provides installation instructions for an optional digital codec card, including unpacking the kit contents, connecting cables between the codec card and main circuit board, securing the codec card with screws and nuts, and replacing covers when complete. Key steps include locating fixing holes, connecting ribbon and link cables observing polarity, and securing BNC connectors before testing the installed digital option.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    45 views1 page

    Octopre Le Optional Codec Installation Guide: Top Cover Removal

    Uploaded by

    taatu
    The 3 sentence summary is: This document provides installation instructions for an optional digital codec card, including unpacking the kit contents, connecting cables between the codec card and main circuit board, securing the codec card with screws and nuts, and replacing covers when complete. Key steps include locating fixing holes, connecting ribbon and link cables observing polarity, and securing BNC connectors before testing the installed digital option.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    OctoPre LE Optional Codec Installation Guide

    The kit should contain: - 1. From the bottom of the chassis, locate the two fixing holes and push
    Qty Description the M3x25mm pan-head screws through the holes into the unit.
    1 Digital card
    2. Place the unit onto a flat surface and fit the two M3 pillars
    2 M3x25mm pozi pan-head screws
    over the screws.
    2 Large nuts and shakeproof washers
    (for BNC connectors) 3. Connect the 34-way ribbon cable CN5 (on the CODEC) to the CN5
    2 M3 Nylok nuts connector on the main circuit board. Observe the polarity bump on the
    2 M3x16mm pillars cable connector for correct attachment.

    4. Disconnect the multi-coloured 10-way link cable from the ‘To ADC’
    Tools required: -
    connector on the main OctoPre LE circuit board, and disconnect the
    No. 1 crosshead screwdriver
    equivalent multi-coloured cable on the CODEC board from the ‘To Main’
    M3 nut driver/spanner
    connector (J12B). Connect the cable from the CODEC board (J11B) to
    16mm socket
    the ‘To ADC’ connector on the OctoPre LE main circuit board, and the
    cable from the OctoPre LE main circuit board to the ‘To Main’ connector
    WARNING!
    on the CODEC (J12B) as shown on the diagram.
    THE MODULE SHOULD BE DISCONNECTED FROM THE AC POWER
    BEFORE ATTEMPTING TO CARRY OUT THE FOLLOWING INSTRUCTIONS. 5. Lower the CODEC board into position as shown in the diagram above,
    ALLOW THE MODULE TO COOL BEFORE STARTING INSTALLATION OF pushing the CODEC BNC connectors into place on the rear panel and
    THE DIGITAL OPTION. ANTI-STATIC PRECAUTIONS SHOULD BE TAKEN align the M3x25 screws to the fixing holes.
    WHEN HANDLING THE CARD OUTSIDE OF ITS ANTI-STATIC BAG; ONLY
    6. Secure the BNC connectors on the rear panel using the two shakeproof
    HANDLE THE CARD BY GRIPPING THE CARD BY ITS EDGES AND AVOID
    washers and two large nuts.
    TOUCHING ANY OF THE COMPONENT PARTS OTHER THAN THE CABLE
    AND CONNECTORS. PLACE THE UNIT ON A CLEAN, FLAT SURFACE. 7. Secure using the two Nylok nuts (do not overtighten).

    8. Connect the black 2-way link cable from the jumper on the CODEC
    that it’s soldered to (J18B) to jumper J18A on the OctoPre LE board as
    Top Cover Removal
    shown in the diagram above.
    1. Remove the 10 crosshead screws securing the top cover.
    2. Remove the top cover. The installed card should look like this:

    Digital Option Cover Removal

    The rear panel digital connector is accessed by removing the small rear
    cover plate. To remove the cover plate push the 2 Richco snap rivet inserts
    from inside the unit, then pull out the rivet body from the rear panel.

    Installing Digital Card


    Replacing the Top Cover
    The top cover should now be replaced, using the 10 crosshead screws,
    to secure it firmly to the chassis. The installation is now complete and
    the unit can be reconnected to the AC power.

    If you experience any difficulties installing this digital option please


    contact Focusrite technical support at [email protected].

    FA0162-02

    You might also like