STATUS INDICATION LAMPS

Lamp.
The lights situated at the bottom of the display show the state of the relay.
Table of relay Outputs with tYPE= 1-2-3-4-13 (Variable speed control)
Output relay N° Relay
HP54 SL 3.1
HEAT 0 1 2 3 4 4 step ventilation + thermoreg.
HEAT 1 0 0 0 0 0 5 Handbook
VENT 1 0 0 1 0 0 0 1
VENT 2 0 0 0 1 0 0 2 MAIN SETTINGS (Run Mode)
VENT 3 0 0 0 0 1 0 3
HEAT TEMPERATURE SETTING.
VENT 4 0 0 0 0 0 1 4
Press HEAT:
This message will be displayed instead of the
Table of relay Outputs with tYPE = 14 (On-Off regulation type)
°Set Heat temperature value .
Lamp. Output relays with tYPE = 14 (see COSt) N° Relay Press + or - to modify, press HEAT to exit.
HEAT 0 1 2 3 4
VENTILATION TEMPERATURE SETTING.
HEAT 1 0 0 0 0 0 5 Press VENT:
VENT 1 0 0 1 0 0 0 1 This message will be displayed instead of the
VENT 2 0 0 1 1 0 0 2 °Set Ventilation temperature value (start first step).
VENT 3 0 0 1 1 1 0 3 Press + or - to modify, press VENT to confirm.
VENT 4 0 0 1 1 1 1 4 At this point: this message will be displayed instead of the
Minimum Ventilation Step (*).
INSTALLATION Press + or - to modify, press VENT to confirm.
How to connect the line At this point: this message will be displayed instead of the
Connect 230V line on terminals L-N. Maximum Ventilation Step.
Protect supply with adequate fuse.
How to connect the sensors HP54 Press + or - to modify, press VENT to confirm.
COOL
Connect the provided sensor as shown in the
diagram. For remote connections use a COMMON (*) If the minimum speed is set to 0, this message appears
standard 0.5-square millimeter two-pole wire HEAT instead of the Set Shutter Running Time (seconds).
, taking great care over the connections, by Press + or - to modify, press VENT to confirm.
insulating and sealing the joins carefully. -O.C.-
is displayed when the temperature sensor wiring At this point: this message will be displayed instead of the
is open, -S.C.- is displayed when the
Shutter Dwell Time (seconds.).
temperature sensor wiring is short circuit.
Press + or - to modify, press VENT to confirm.
How to connect the contacts
SX TEMPER.
230V LINE *

Output contacts are N.O. (Normally At this point: this message will be displayed instead of the
COMMON

Opened free of voltage) on wich is apliable

Shut Speed Number.
PROBE
STEP 1
STEP 2
STEP 3
STEP 4

a 4AMP AC1 maximum load.

3-4= Step 1 contact Press + or - to modify, press VENT to exit.
3-5= Step 2 contact
3-6= Step 3 contact ALARM PARAMETER SETTING.
3-7= Step 4 contact Press ALARM:
11-12= Heat contact * Other power voltage if you required This message will be displayed instead of the
12-13= Cool contact
°Set Minimum Alarm temperature value .
Alarm and Cooling are available only with
HPAL optional slot. Press + or - to modify, press ALARM to confirm.
At this point: this message will be displayed instead of the
12.02.13

As it company policy to continually improve the products the Manufacturers

reserve the right to make any modifications thereto without prior notice. They
°Set Maximum Alarm temperature value .
cannot be held liable for any damage due to malfunction. Press + or - to modify, press ALARM to exit.
VIEWING TEMPERATURE RECORDING MANUAL MODE
Press + : will be displayed followed by In some start-up conditions may be useful to work in "manual" mode:
°Maximum Temperature Recording. Power off the processor, press + key and keep it pressed giving power on: HAnd
Press - : will be displayed followed by message will be displayed (release now + key).
°Minimum Temperature Recording. Push + until is displayed number required to be handed (see table State
Values recorder are memory permanent stored: for memory clear keep pushed + keys for more than indication lamps ) and push ALARM for activing relay.
3 seconds: CLEA message will be composed on display before clearing operation. Pushing again + for increase relay number previous relay is disactivated.
You can press ALARM key for a least two seconds to escape and return to the Run Mode.
COSt PROGRAMMING (System constants)
These settings refer to the operation mode of the system and must be made on initial
OPERATIVE DIAGRAMS
startup. Press - / + at the same time for at least one second: the message C.O.S.t. will be
displayed. Press than repeatedly ALARM until the message regarding the chosen variable
is displayed (see table below): variable’s value and message will be displayed.
Press + or - to set a new value and then press ALARM to confirm. d.FAn
The next system constant will then appear. V 4 ON

You can press ALARM for at least 2 seconds to exit and return to the Run Mode. If Minimum speed is programmed to 0
CONDIZIONATED

d.FAn V4 BY SP. - -

Mess. Valore Meaning Note (SP._ _=0), when the ventilation is off it is
d.HEA 0.2 ° °HEAT differential *1 possible to insert a cyclical operation of
minimum speed, composed of a turn-on V3 With tYPE = 13 :
rEL.1 0.0 ° ° Temperature set of step 1 referred to the vEnt set *1 time fans (t.on), by a switch-off time fans d.FAn
1.0 ° ° Temperature set of step 2 referred to the Step 1 start *1 V0 V4
rEL.2 (t.oF), and the selected speed during
rEL.3 1.0 ° ° Temperature set of step 3 referred to the Step 1 start *1 an’s shuttering operation (SP- -). V1 V3
V2
rEL.4 1.0 ° ° Temperature set of step 4 referred to the Step 1 start *1
d.FAn V2 V2
d.FAn 0.2 ° ° Ventilation differential *1 V3 V1
V1 V4 V0
r.COL 6.0 ° ° COOL setting shift referring to vEnt set *1 Heater mode ventilation
d.COL 0.2 ° ° COOL differential *1
tEnP =1 Temperature unit (=1: °C, =2: °F) t.on t.oF t.on t.of rEL.2 rEL.3 rEL.4

Ad.tE 0.0 ° ° Temperature sensor adjustment (+ or -) *2 rEL.1

tYPE 1 Start ventilation actioning mode *3

Step from 0 to 1 speed become according d.COL
*1) For more details see Operative Diagrams to chosed COSt function tYPE. COOL ON

*2) You can correct the readings on the sensor (+ or -).

*3) Different mode of ventilator initial start-up optionally settable (step from 0 to 1 speed). COOL
tYPE= 1 : 0 to 1 step become in normal mode.
COOL OFF
tYPE= 2 : 0 to 1 step become with a momentary 10 seconds at speed 2.
tYPE= 3 : 0 to 1 step become with a momentary 5 seconds at speed 3. r.COL
tYPE= 4 : 0 to 1 step become with a momentary 5 seconds at speed 4.
tYPE=13 : Heating mode ventilation. vEnt
tYPE=14 : Progressive ventilation contacts (On-Off regulation type).
Options 2, 3 , 4 permits to make an easy opening of shutter models ventilators. AMB. TEMP.

Option 13 permits Heater mode ventilation (low temperature = higt speed; in other options high d.HEA 0.2° 0.2°
temperature= high speed). HEAT ON MIN ON MAX ON
Option 14 permits On-Off regulation mode (in other condition regulation is for variable speed control).

MIN MAX
PRESET PROGRAMS (bootstrap) HEAT ALARM ALARM
This processor is already programmed with the following (variable) settings.
To return to these settings at any time you may:
HEAT OFF MIN OFF MAX OFF
Power off the processor, press MAX VENT key and keep it pressed giving power on: boot
message will be displayed (release now MAX VENT key).
HEAt AL._ _ AL.- -
HEAt = 20.0° vEnt = 25.0° SP._ _= 0 SP.- - = 4 AL._ _= 10.0° AL.- - = 40.0° AMB. TEMP. AMB. TEMP. AMB. TEMP.
t.on = 10" t.oF = 60" SP.-- = 0 The COSt values are shown in COSt Promagramming.