Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology

ISSN No:-2456-2165

IOT Based Automatic Water

Container Filler Using Arduino
1
Ashish Mishra, 2Sarvgya Yadav, 3Shweta Singh, 4Vineet Pandey, 5Vishal Dwivedi, 6Deepti Ojha
1,2,3,4,5
Student, Department of ECE, ITM, GIDA, Gkp, UP, India
6
Head of Department, Department of ECE, ITM, GIDA, Gkp, UP, India

Abstract:- The objective of our project is to design, mechanical and digital machines, objects, animals or people
develop and monitor “Automatic Water Container that are provided with sole identifiers (UIDs) and the ability
Filler using Arduino”. This work provides with a lot of to transfer data over a network without requiring human-to-
benefits like low power feeding, low functioning cost, human or human-to-computer communication. With this
less care, accuracy and many more. This project is concept , few more concept is also required for our Project
based on automation and is a vast application IOT i.e,
concept. A prototype has been developed to illustrate  The concept of I2C
the project. Feeding the container in hand to hand is the  How to govern DC motor through Arduino?
main task that is carried out by a machine and this  How to govern ultrasonic sensors through Arduino?
process is commonly used by many Robot.  What is the function of LDR sensor and how it works?
 What is the function of timer and how it works?
Keywords:- IOT, Automation, Sensors, Arduino, 555 Timer.
This Project is to feed the water filled container in
I. INTRODUCTION hand to hand or to the particular position with the help of
the above mention concept. This Project consists of –
In this paper, This Project is based on the concept of  Electronic System
IOT (Internet of Things). The cyberspace of things,  Software Controlled by Arduino UNO
or IOT, is a system of unified calculating devices,

II. BLOCK DIAGRAM M2 , M5 are connected to Master Arduino. Ultrasonic

Sensor US3 and Motor M1, M3, M4 are connected to Slave
There are two Arduino UNO board which are Arduino.
connected in series by using the concept of I2C and all the
control of the system id done through these two Arduino. After the measurement of water level and height of
Arduino 1 acts as Master Arduino and Arduino 2 acts as the container with the help of US1, US2, US5 message is
Slave. Ultrasonic Sensor US1, US2, US5, US4 and Motor send to Robot. If the container is empty of half filled, M1

IJISRT20JUN275 www.ijisrt.com 370

Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
comes into function and moves towards the container.
When it comes near the door M2 starts working and door
opens automatically and the distance between robot and
door is measured by US3 ,which is attached in the front of
the robot. Then Robot moves towards the container and
Robotic Arm M3, M4 comes into function and pick the
container and put it under the tap. When it comes under the
tap US4 continuously measure the water level and M5
starts ,which moves downwards with the help of rack
pinion and comes in between the LDR and Led , this makes
the tap to open due to trigger in 555 timer. When container
is filled completely Again Robot pick and place it at its
position.

III. THEORY
 LDR Sensor:
A. Arduino UNO An LDR or light dependent resistor is also known as
Arduino is an open-source microchip technology photo resistor, photocell, photoconductor. It is a one type of
platform based on easy-to-use hardware and software. The resistor whose resistance varies depending on the quantity
Arduino Uno is a microcontroller board based on the of light falling on its surface. When the light falls on the
ATmega328. It has 20 digital input/output pins (of which 6 resistor, then the resistance changes. These resistors are
can be used as PWM outputs and 6 can be used as analog often used in many circuits where it is required to sense the
inputs), a 16 MHz resonator, a USB connection, a power existence of light.
jack, an in-circuit system programming (ICSP) header, and
a reset button. It contains everything needed to support the
microcontroller; simply connect it to a computer with a
USB cable or power it with a AC-to-DC adapter or battery
to get started.

The Uno differs from all previous boards in that it

does not use the FTDI USB-to-serial driver chip. Instead, it
features an ATmega16U2 programmed as a USB-to-serial
converter. This auxiliary microcontroller has its own USB
bootloader, which allows forward-thinking users to
reprogram it.

C. 555 Timer
555 timer is used in almost every electronic circuit
today. For a 555 timer working as a flip flop or as a multi-
vibrator, it has a particular set of arrangements. It operates
from a wide range of power ranging from +5 Volts to +18
Volts supply voltage. Sinking or sourcing 200 mA of load
current. The external components should be selected
properly so that the timing breaks can be made into several
minutes along with the frequencies more than several
hundred kilohertz.

B. Sensors
 Ultrasonic Sensor:
Ultrasonic sensors calculate distance by using
ultrasonic waves. The sensor head emits an ultrasonic wave
and receives the wave reflected back from the target.
Ultrasonic Sensors measure the distance to the target by
measuring the time between the emission and reception.

IJISRT20JUN275 www.ijisrt.com 371

Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165

D. DC Geared Motor
The motor we have used is Center shaft 100 rpm dc
geared motors specifically designed for robotic applications
.It is very easy to use. It has Nut and threads on shaft to
easily connect and internal threaded shaft for easily IV. COMPLETE PROJECT SYSTEM
connecting it to wheel. Easy to use and mount, long
durability and very affordable considering the features. A. Mechanism
These motors open a wide choice for us in terms of rolls Firstly, Level of the Water and height of the container
and chassis. is measured. If the water level is less than half, then robot
will move towards the container. When robot comes near
These motors are simple DC Motors containing gears the container door open automatically and robotic arm pick
for the shaft for obtaining the optimal performance the container ant put it under the tap. Vertical level
characteristics. They are known as Center Shaft DC Geared indicator comes into function and tap opens automatically.
Motors because their shaft covers through the center of When water filled into container Robot and robotic arm
their gear box assembly. again pick it up and place it at its position.

E. L293D Motor Driver

L293D is a typical Motor driver or Motor Driver IC
which allows DC motor to drive on either direction. L293D
is a 16-pin IC which can control a set of two DC motors at
once in any direction. It means that you can control two DC B. Software Implementation
motor with a single L293D IC. It works on the concept of The software part programming done through Arduino
H-bridge. Uno software (IDE). It is easy to write code and upload it to
the board. C and C++ language are used for programming.
In this project, programming is done in two phase. Firstly,
program for Master Arduino had been written. Then after
program for Slave Arduino had written. And the link
between these two Arduino is done by using the concept of
I2C.

IJISRT20JUN275 www.ijisrt.com 372

Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165

C. Connection
The connection of Ultrasonic Sensor with Arduino are
as follows:
 Vcc to 5V Pin of the Arduino UNO board.
 Gnd to Gnd Pin of the Arduino UNO board.
 Trig to Digital Pin of the Arduino UNO board.
 Echo to Digital Pin of the Arduino UNO board.

The connection of DC Geared Motor using interface

of L293D with Arduino are as follows:
 Connect 5V and ground of the IC to 5V and ground of
Arduino.
 Connect the motor to pins 2 and 3 of the IC.
 Connect IN1 of the IC to pin 8 of Arduino.
 Connect IN2 of the IC to pin 9 of Arduino.
 Connect EN1 of IC to pin 2 of Arduino.
 Connect SENS A pin of IC to the ground.

IJISRT20JUN275 www.ijisrt.com 373

Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
B. Applications
 The model can be used in schools, colleges, hotels etc to
avoid trafficking.
 In stadiums where there is very large gatherings, this
will help a lot. The same thing is also possible in
marriage functions, ceremonies, events, parties etc..
 It will be time saving, where we can save a lot of time.
We won’t have to rely on anyone to fill the water bottle.
 It will also be revolution for the midgets. Midgets
always face difficulty in getting the water containers
from the two storey fridges but with this model they
will not face any difficulty in getting so.
 The use of cheap components makes this project very
cost effective. So if it comes in the market then it’s
availability will be high and affordable to all.
 This model can be used in beverages and soft drinks
industries. And using Arduino against PLCs makes it’s
chances go higher.

C. Future Scopes
This model can be widely used in schools, colleges,
malls, hotels, restaurants etc. where gathering of people is
commonly more. At these places, serving of water is the
best scope that looks to be something that can be
implemented. We are still not having system which serves
the water filled glasses to us. So with few implementations
in the flexes this can be made possible .

At the same time the use of robotic arms can also be

implemented further for water saving process. The amount
of water left can be put back by the arm and we can refilter
it for further uses. When glass is controlled by the robotic
arm then also this possibility becomes more as the arm is
being controlled through the programs and with such
implementation using water level indicator, this task can be
done.

VI. RELATED WORKS

There are lots of project present in today’s market

related to this topic but looking onto the present scenario,
V. SIGNIFICANCE AND SCOPE this project is very much feasible in the market because it is
very cheap, not complex, and can be understood easily.
A. Necessity
The idea/necessity seen for this project comes from a  Fully Automatic Water Tank Level Controller Magnetic
real incident. The project deals with a practical problem Sensors
which is very common in households i.e. water bottle re- Motor robotically switch off if no water in supply pipe
filing. or tank is full. Magnetic sensors for long life with No
corrosion, carbon and oxidation of sensors and no
Mother in houses are mostly worried for the same sanitation required for installation. Moisture resistant PTH
problem. The same incident took place on one of our group printed circuit board and water-resistant ABS plastic wall
member house too. Then the idea of automatic water bottle rising enclosure. Feather touch buttons and LED for water
re-filing strikes our mind. level indication and the sleek design gives your home
contemporary outlook Automatic and manual mode is
Another incident which motivated us was that a present.
relative of mine met an accident and the person was all
alone at the house. For drinking water the filing could not
be possible. With the help of our project we can tackle such
simple yet most common problems.

IJISRT20JUN275 www.ijisrt.com 374

Volume 5, Issue 6, June – 2020 International Journal of Innovative Science and Research Technology
ISSN No:-2456-2165
 The SGF2/100 rotary oral liquid filler & sealer is the
automatic liquid filling machine investigated as well as
produced by our company in the recent years for
flattering the source development using the electrical
and mechanical technique. Also this automatic liquid
filling machine is utilized to fill and seal the liquid
produced for health, products, machine, oral liquid
preparations and also chemical, food, & cosmetics.

VII. CONCLUSIONS

We here conclude that our project “Automatic water

Container Filler“ has been successfully completed under
our group and through mentor’s help.

Whatever we had mentioned in our abstract we have

done the same and used the procedure as mentioned earlier.
Also at the same time we are highly pleased our efforts and
the system is working very well.

Therefore with an automatic filling machine one can

ensure speed and easy filling processes to ensure efficient
filling of liquids or powders into bottles without wastage.

REFERENCES

[1]. "Getting Started: FOUNDATION >

Introduction". arduino.cc.
[2]. David Kushner (2011-10-26). "The Making of
Arduino". IEEE Spectrum.
[3]. Justin Lahart (27 November 2009). "Taking an Open-
Source Approach to Hardware". The Wall Street
Journal.
[4]. Hernando Barragán (2016-01-01). "The Untold
History of Arduino". arduinohistory.github.io.
[5]. "How many Arduinos are "in the wild?" About
300,000". Adafruit Industries.
[6]. "Arduino FAQ – With David Cuartielles". Malmö
University. April 5, 2013.
[7]. "The Foundation of Today's Digital World: The
Triumph of the MOS Transistor". Computer History
Museum.
[8]. Omura, Yasuhisa; Mallik, Abhijit; Matsuo, Naoto
(2017)”MOS Devices for Low-Voltage and Low-
Energy Applications”. John Wiley & Sons.
[9]. Vongsingthong, S.; Smanchat, S. (2014). "Internet of
Things: A review of applications &
technologies" (PDF). Suranaree Journal of Science
and Technology.
[10]. "The Enterprise Internet of Things Market". Business
Insider.

IJISRT20JUN275 www.ijisrt.com 375