Scribd
Upload
113 views1 page

STD.22 Parameters Details

This document is a gyro service form used to record measurement values during gyro maintenance. It lists nominal and acceptable range values for various gyro components including power voltages, currents, temperatures, and software versions. Service technicians would use this form to check that components are functioning properly and record any values outside of normal ranges.

Uploaded by

Jay Sanchaniya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
113 views1 page

STD.22 Parameters Details

This document is a gyro service form used to record measurement values during gyro maintenance. It lists nominal and acceptable range values for various gyro components including power voltages, currents, temperatures, and software versions. Service technicians would use this form to check that components are functioning properly and record any values outside of normal ranges.

Uploaded by

Jay Sanchaniya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Gyro STD.

22 Service Form
Vessel Name: Date:
Gyro Sphere No: Last Gyro Service Date:
Last Gyro Sphere Changed Date:

Value At Value At Value At Value At Value At


Display Function Nominal Value
Reading measured data of
GYro
the gyro
Enco Encoder value
ALEr Alignment error 0.00
SEC SEC value 0.00
24 V ships mains after input
Pbor 18.0 to 36.0V
filter 12-32 V
14 V for 60 V inverter on
Co14 14.0 to 16.0V
power pcb
P-En 15 V for Encoder supply 14.5 to 15.5V
60 V stabilized /ferrite
P-60 58.0 to 62.0V
transformer bridge

Co19 19 V from ferrite transformer 18.0 to 22.0V

Current of ferrite 0.05 to 4.0A


IndA
transformer bridge (Typical 2.0A)
Co31 Voltage for heating circuit 27.0 to 32.0V
C°-U Voltage on heater element 0 to 23.5V
Supporting liquid
-C°- 49.4 to 50.1°C
temperature
2.0 - 1.6 = Level OK
Li-U Supporting liquid level
0.1 - 0.0 = Level too Low

Co73 73 V from ferrite transformer <65.0 to 79.0V

78 V stabilized for gyro Ac


78-U 77.0 to 79.5VDC
converter
At Start-up 45 to 60V
GY-U Gyro supply voltage
At operation 53 to 58V
At Start-up 150 to 400mA
GY-A Gyro supply current
At operation 120 to 350mA

Co15 15 V from ferrite transformer <15.5V

P-15 15 V stabilized 14.5 to 15.5 VDC


24 V / 50 Hz for pump AC
P-24 23 to 35 VDC
converter
24 V / 50 Hz AC pump
U-Pu 23.5 to 24.5V
voltage
A-Pu Pump current 140 to 180mA
Ab9r Follow up voltage W1 / W2 <5mV

Pr-S Software sensor pcb 1.0.1


Pr-P Software power pcb 2.0.0
Software MC1 outer sphere
Pr61 3.0.0
pcb
Software MC2 outer sphere
Pr62 4.0.0
pcb
runY Operating years
Runh Operating hours
7 Future purpose
8 Future purpose

Engineer's Name:

You might also like