PIPING DESIGN &

ARRANGEMENT
24 - 26 April 2018 | 29 - 31 October 2018
Block M4, IBD UTM Kuala Lumpur, MALAYSIA

Institute of
Bioproduct Development Steinbeis
Chemical Engineering
Pilot Plant
MS ISO/IEC 17025
TESTING
Malaysia Foundation
UNIVERSITI TEKNOLOGI MALAYSIA SAMM NO. 433

COURSE INTRODUCTION COURSE CONTENT

The course will review the basic requirements of Piping Arrangement & Pipe Support
Design with emphasis on pipe routing design practices and requirements on compres-
Day 1 : Piping Material
sor , pump , heat exchanger , air cooler, vessel, flare system piping layout. A general 1. General Piping Material .
overview of piping material , pipe flexibility and pipe stress requirements will be included 2. Piping Standard , & Introduction to ASME B31.3.
in this course. Application of these concepts include practical case studies on offshore 3. Pipes Fittings & Components
piping layout, piping material selection, MTO review , pipe stress studies, and general 4. Flange Design & Selection
Piping Fit For Life (FFS ) Study as per ASME B31.3 requirements. 5. Piping Class & Piping Material Specification
6. Pipe Thickness Calculation
7. Valves- Concept, Selection & Data Sheet
COURSE OBJECTIVES 8. Piping MTO.
This course provides the necessary knowledge for those who are responsible for design-
ing and constructing a new piping system, particularly on offshore environment, and 9. Piping System – Fit For Services
those who oversee and ensure the integrity of existing piping system. 10. Case Studies

The objectives of this course are to enable participants to: Day 2 : Piping Equipment Layout & Arrangement
1. Understand Pipe Routing & Arrangement Design Concepts & Requirements.
1. PFD, P& ID considerations in Piping Design
2. Understand Pipe Support Design Concept, and Pipe Span Requirements.
2. Piping Design & Arrangement Requirement
3. Understand P&ID & PFD for Piping Arrangement Design.
4. Understand Piping Stress Isometric for Pipe Support Design . 3. Standard & Special Pipe Support
5. Understand General Pipe Flexibility and Pipe Stress Requirements. 4. Piping Equipment Layout & Arrangement:
6. Understand General Piping Material Requirements. Compressor Piping; Pump Piping; Heat Exchanger
Piping; Air Cooler Piping; Vertical & Horizontal Vessel
After completing this subject the participants should be able to: Piping
1. Perform piping arrangement and layout design as normal engineering 5. Piping Interfaces : Process/ Structure/ Mechanical
practices & piping code requirements. /Electrical
2. Perform pipe support design. 6. Piping Drawings Piping GA, Pipe Support Location Plan,
3. Generate, review and check of piping isometric drawings. Isometric, etc.
4. Generate & review piping & valve specifications, piping materials & valve
data sheets , piping material take off (MTO).
5. Review & perform general piping material selection. Day 3 : Pipe Stress Analysis
6. Perform simple pipe flexibility studies and review pipe stress analysis 1. Fundamental Theory & Concept of Pipe Stress Analysis
report. 2. Pipe Flexibilities & Calculation
3. Piping Force & Moment, Friction, Stress Intensification
Factor, Elbow Flexibilities
WHO SHOULD ATTEND 4. Pipe Expansion Loop
Engineer,
5. Pipe Failure Theory & Code Requirements
Senior Piping Designer,
6. Load Cases- Sustain, Operation, Thermal, Occasional
Piping Designer,
7. Spring Design & Selection
Plant Supervisors & Operator,
8. Stress Isometric Interpretation
Piping inspectors and party with involvement on process piping working in Oil &
9. Stress Analysis Inputs Parameters & Stress Analysis
Gas ,
Report
Chemical Plant,
Interpretation :
Power industries, etc.
Code Compliance; Restraint Summary; Load
Interpretation
10. Case Studies
COURSE TUTOR

MR. SAM WEI YEOW

Mr. Sam Wei Yeow is a ASME B31.3 Code Review Committee Member, and a registered
professional engineer with BEM ( Board of Engineer) Malaysia. He has 17 years of piping
design and project management experiences, and has extensively involved in piping
design & construction in many offshore and power plant projects with emphasis on piping
equipment layout, piping arrangement & pipe support design and pipe stress analysis.

He had also conducted numerous technical talks at Institute of Engineer ( IEM) , Malaysia
and Offshore Technical Conference, and public course on engineering topics related to
Piping Design. Mr. Sam also has a great passion in using 3D modeling in engineering
design, supporting site construction, plant operation and maintenance activities.

Piping Design & Arrangement COURSE FEE We can offer courses

Fee is inclusive of lunch, refreshments and course in-house at your company
materials. Accommodation is not included.
Please tick ( ) where appropriate Staff from more than 700 local and
[ ] 24 - 26 April 2018 [ ] 29 - 31 October 2018 Local Participant
RM3710 | International Participant
EURO1950
overseas companies have attended
our life-long learning programmes
YES! I would like to register the following participants
Name 1
Method of Payment Some of these companies are :
Please kindly complete and return the PETRONAS, SHELL, BP, SAUDI ARABIA BASIC
reply form 3 weeks before the IND. CORP. (SABIC), QATAR LNG, ALMARAI
Job Title commencement date together with : (SAUDI ARABIA), IDEMITSU, EASTMAN
CHEMICALS, BASF PETRONAS, KUWAIT
Name 2 Local Participant
INSTITUTE OF SCIENTIFIC RESEARCH,
Cheque / Bank Draft which are made payable KHARTOUM REFINERY, LOADSTAR (Sri Lanka)
Job Title to PHYTO BIZNET SDN. BHD. etc.
COMPANY INFORMATION
International Participant
Company Direct Transfer/Bank Draft :
IBD Bank details : For more information, please contact
Address
CIMB Bank Berhad, INSTITUTE OF BIOPRODUCT DEVELOPMENT
Town Universiti Teknologi Malaysia UNIVERSITI TEKNOLOGI MALAYSIA
81310 UTM Johor Bahru, Johor, Malaysia 81310 UTM Johor Bahru, Johor
State
tel +607.553 6486
Please instruct your bank to remit us the full amount, net of
Tel Fax bank charges fax+607.553 6464
Mrs Asrin | [email protected]
Account No : 0118 - 0004178 - 05 - 7
Email IBD UTM Jalan Sultan Yahya Petra
Swift Code CIBBMYKL 54100 Kuala Lumpur
Authorised Signatory (*This registration is invalid without signature
from an authorised officer)
Cancellation & Substitutions tel +603.2615 4406
A full refund will be promptly made for all written fax+603.2693 7921
Name Mrs Yatie | [email protected]
cancellations 2 weeks before the course. 50%
Job Title refund will be made for written cancellations received
7 days before the course. A substitute may be made www.ibd.utm.my
Tel Fax at any time.
Note
Email A) The organiser has the right to make any amend-
UTM Kuala Lumpur is situated about 10
minutes drive from the famous Kuala Lumpur
ments that they deem to be in the best interest of the
landmark, the PETRONAS TWIN TOWER and
course and to cancel the course if insufficient
KLCC, the prime shopping centre. It is easily
registrations are received a week before course
accessible by road and major hotelsare
Signature commencements date.
located nearby.
B) CERTIFICATE OF ATTENDANCE will be awarded at
the end of the course.