Sensor selection guide

Global competition and pressure on corporate performance makes productivity a primary concern for any business.
Machinery vibration monitoring programs are effective in reducing overall operating costs of industrial plants.
Vibration signals produced by industrial machinery are effective indicators of machinery health. Monitoring vibration
levels over time records the machine’s vibration history, allowing plant engineers to predict problems before serious
damage or failure occurs. Machinery damage and costly production delays caused by machinery failure can be
prevented – when problems are discovered early, there is an opportunity to schedule maintenance and thereby
reduce downtime in a cost-effective manner. Vibration analysis is used as a tool to determine machine condition and
the specific cause and location of machinery problems. This expedites repair and minimizes cost.

This technical note will cover the important factors to consider when choosing a vibration sensor. These include
environmental conditions in the plant, the type of machinery being monitored, and the types of vibration sensors.
Sensor specifications and their relevance to industrial applications are discussed.

Common vibration sensors

Critical to vibration monitoring and analysis is the machine-mounted

sensor. Three parameters representing motion detected by vibration
monitors are displacement (in inches), velocity (in inches per second,
or ips), and acceleration (in g’s). These parameters are mathematically
related and can be derived from multiple types of motion sensors.
Selection of a sensor proportional to displacement, velocity or
acceleration depends on the frequencies of interest and the signal
levels involved. Figure 1 shows the relationship between velocity and
displacement versus constant acceleration. Proper sensor selection
and installation is crucial to accurately diagnosing machine condition.

Displacement sensors

Displacement sensors are used to measure shaft motion and internal clearances. Monitors have used non-contact
proximity sensors, such as eddy probes, to sense shaft vibration relative to bearings or other support structures.
These sensors are best suited to measuring low frequency and low amplitude displacements typically found in
sleeve bearing machine designs. Piezoelectric displacement transducers (doubly integrated accelerometers) have
been developed to overcome problems associated with mounting non-contact probes, and are more suitable for
rolling element bearing machine designs. Piezoelectric sensors yield an output proportional to the absolute motion
of a structure, rather than relative motion between the proximity sensor mounting point and the target surface.

8435 Progress Drive Tel: +1 (301) 330 8811 wilcoxon.com Wilcoxon Sensing Technologies
Frederick, MD 21701 [email protected] buy.wilcoxon.com
Velocity sensors

Table 1: Coil and magnet vs. piezoelectric velocity sensors

Velocity sensors are used for low to medium frequency
measurements. They are useful for vibration monitoring Coil and magnet Piezoelectric

and balancing operations on rotating machinery. As Flat frequency response

20 - 1,500 Hz Yes Yes
compared to accelerometers, velocity sensors have lower 2 - 5,000 Hz No Yes
sensitivity to high frequency vibrations, making them Phase fidelity
less susceptible to amplifier overloads. Overloads can 2 - 5,000 Hz Poor Excellent

compromise the fidelity of low amplitude, low frequency Low off-axis sensitivity No Yes

signals. Traditional velocity sensors use an electromagnetic Reduced noise at high No Yes
frequencies
(coil and magnet) system to generate the velocity signal.
Linearity Good Good
Now, hardier piezoelectric velocity sensors (internally
Mounting in any orientation No Yes
integrated accelerometers) are gaining in popularity due
Operation to 120°C Yes Yes
to their improved capabilities. A comparison between the
EMI resistance Poor Excellent
traditional coil and magnet velocity sensor and the modern
Mechanical durability Fair Excellent
piezoelectric velocity sensor is shown in Table 1.

Accelerometers

Accelerometers are the preferred motion sensors for most vibration monitoring applications. They are useful for
measuring low to very high frequencies and are available in a wide variety of general purpose and application-
specific designs. The piezoelectric accelerometer is unmatched for frequency and amplitude range. Accelerometers
are versatile, reliable and the most popular type of vibration sensor for industrial machinery monitoring.

Piezoelectric sensors

The rugged, solid-state construction of industrial piezoelectric sensors enables them to operate under most harsh
environmental conditions. They are unaffected by dirt, oil and most chemical atmospheres. They perform well over a
wide temperature range and resist damage due to severe shocks and vibrations. Most piezoelectric sensors used in
vibration monitoring today contain internal amplifiers.

The piezoelectric element in the sensor produces a signal proportional to acceleration. This small acceleration
signal can be amplified for acceleration measurements or electronically integrated within the sensor into a velocity
or displacement signal. The piezoelectric velocity sensor is more rugged than a coil and magnet sensor, has a wider
frequency range, and can perform accurate phase measurements.

Piezoelectric materials

The two basic piezoelectric materials used in vibration sensors today are piezoelectric ceramics and quartz. While
both are adequate for successful sensor design, differences in their properties allow for design flexibility. For
example, quartz has lower charge sensitivity and exhibits a higher noise floor than modern piezoceramic materials.
Most vibration sensor manufacturers now use piezoceramics developed specifically for sensor applications. Special
formulations yield optimized characteristics to provide accurate data in extreme operating environments. The
exceptionally high output sensitivity of piezoceramics allows for the design of sensors with increased frequency
response when compared to quartz.

Page 2
Much has been said of the thermal response of quartz versus piezoceramics. Both materials exhibit an output during
a temperature change (known as the pyroelectric effect) when the material is not mounted within a sensor housing.
Although this effect is much lower in quartz, when properly mounted within the sensor housing the elements are
isolated from fast thermal transients. The difference in materials then becomes insignificant. The dominant thermal
signals are caused by metal case expansion strains reaching the base of the crystal. These erroneous signals are
then a function of the mechanical design, rather than of the sensing material. Proper sensor designs isolate strains
and minimize thermally induced signals. (See the section “Temperature range” on page 5.)

High quality piezoceramic sensors undergo artificial aging during the production process. This ensures stable and
repeatable output characteristics for long term vibration monitoring programs. Theoretical stability advantages of
quartz over ceramic designs are eliminated as a practical concern.

The development of advanced piezoceramics with higher sensitivities and capability to operate at higher
temperatures is anticipated.

Choosing an industrial sensor

When selecting a piezoelectric industrial vibration sensor (acceleration, velocity or displacement), many factors
should be considered to make sure the selection is the best one for the application. The user who addresses
application-specific questions will become more familiar with sensor requirements.

Typical questions include:

• What is the vibration level?
• What is the frequency range of interest?
• What is the temperature range required?
• Are any corrosive chemicals present?
• Is the atmosphere combustible?
• Are intense acoustic or electromagnetic fields present?
• Is there significant ESD present in the area?
• Is the machinery grounded?
• Are there sensor size and weight constraints?

Related questions concerning the connectors, cables and associated electronics:

• What cable lengths are required?
• Is armored cable required?
• To what temperatures will the cable be exposed?
• Does the sensor require a splash-proof connector?
• What are the power supply requirements?

Primary sensor considerations

Two of the main parameters of a piezoelectric sensor are the sensitivity and the frequency range. In general, most
high frequency sensors have low sensitivities and, conversely, most high sensitivity sensors have low frequency
ranges. It is therefore necessary to compromise between the sensitivity and the frequency response.

Page 3
The sensitivity range

The sensitivity of industrial accelerometers typically ranges between 10 and 100 mV/g; higher and lower sensitivities
are also available. To choose the correct sensitivity for an application, it is necessary to understand the range of
vibration amplitude levels to which the sensor will be exposed during measurements.

As a rule of thumb, if the machine produces high amplitude vibrations (greater than 10 g rms) at the measurement
point, a low sensitivity (10 mV/g) sensor is preferable. If the vibration is less than 10 g rms, a 100 mV/g sensor
should generally be used. In no case should the peak g level exceed the acceleration range of the sensor. This
would result in amplifier overload and signal distortion, generating erroneous data. Higher sensitivity accelerometers
are available for special applications such as low frequency/low amplitude measurements. In general, higher
sensitivity accelerometers have limited high frequency operating ranges. One of the excellent properties of the
piezoelectric sensor is its wide operating range. It is important that anticipated amplitudes of vibration fall reasonably
within the operating range of the sensor. Velocity sensors with sensitivities from 20 to 500 mV/ips are available. For
most applications, a sensitivity of 100 mV/ips is satisfactory.

The frequency range

In order to select a sensor with the appropriate frequency range, it is necessary to determine the frequency
requirements of the application. This range is often already known from vibration data collected from similar systems
or applications. The plant engineer may have enough information on the machinery to calculate the frequencies of
interest. Sometimes the best method to determine the frequency content of a machine is to place a test sensor at
various locations on the machine and evaluate the data collected.

The high frequency range of the sensor is constrained by its

increase in sensitivity as it approaches resonance. The low
frequency range is constrained by the amplifier roll-off filter, as
shown in Figure 2. Many sensor amplifiers also filter the high end of
the frequency range in order to attenuate the resonance amplitude.
This extends the operating range and reduces electronic distortion.

Most vibrations of industrial machinery contain frequencies below

1,000 Hz (60,000 CPM), but signal components of interest often
exist at higher frequencies. For example, if the running speed of a
rotating shaft is known, the highest frequency of interest may be
a harmonic of the product of the running speed and the number of bearings supporting the shaft. The user should
determine the high frequency requirement of the application and choose a sensor with an adequate frequency
range, while also meeting sensitivity and amplitude range requirements. (Note that sensors with lower frequency
ranges tend to have lower electronic noise floors. Lower noise floors increase the sensor’s dynamic range and may
be more important to the application than the high frequency measurements.)

High amplitude vibration signals

The sensor operating environment must be evaluated to ensure that the sensor’s signal range not only covers the
vibration amplitude of interest, but also the highest vibration levels that are present at that measurement point.
Exceeding the sensor’s amplitude range can cause signal distortion throughout the entire operating frequency range
of the sensor.

Page 4
Temperature range

Sensors must be able to survive temperature extremes of the application environment. The sensitivity variation
versus temperature must be acceptable to the measurement requirement. Temperature transients (hot air or oil
splash) can cause metal case expansion, resulting in erroneous output during low frequency (<5Hz) measurments.
A thermal isolating sleeve should be used to eliminate these errors.

Humidity

All vibration sensors are sealed to prevent the entry of high humidity and moisture. In addition, cable connectors and
jackets are available to withstand high humidity or wet environments.

Hazardous areas

Vibration sensors certified as being intrinsically safe should be used in areas subjected to hazardous concentrations
of flammable gas, vapor, mist, or combustible dust in suspension. Intrinsic safety requirements for electrical
equipment limit the electrical and thermal energy to levels that are insufficient to ignite an explosive atmosphere
under normal or abnormal conditions. Even if the fuel-to-air mixture in a hazardous environment is in its most volatile
concentration, intrinsically safe sensors are incapable of causing ignition; this greatly reduces the risk of explosions.

Electrical powering requirements

Most internally amplified vibration sensors require a constant current DC power

source. Generally, the power supply contains an 18 to 30 V source with a 2
to 10 mA constant current diode (CCD) (see Figure 3). When other powering
schemes are used, consultation with the sensor manufacturer is recommended.
A more thorough discussion of powering requirements follows.

AC coupling and the DC bias voltage

The sensor output is an AC signal proportional to the vibration of the structure

at the mounting point of the sensor. This AC signal is superimposed on a DC bias voltage (also referred to as bias
output voltage (BOV) or rest voltage). The DC component of the signal is blocked by a capacitor. This capacitor,
however, passes the AC output signal to the monitor. Most monitors and sensor power supply units contain an
internal blocking capacitor for AC coupling. If not included, a blocking capacitor must be field installed.

Amplitude range and supply voltage

The sensor manufacturer usually sets the bias voltage halfway

between the lower and upper cutoff voltages (typically 2 V above
ground and 2 V below the minimum supply voltage). The difference
between the bias and cutoff voltages determines the voltage swing
available at the output of the sensor. The output voltage swing
determines the peak vibration amplitude range (see Figure 4). Thus,
an accelerometer with a sensitivity of 100 mV/g and a peak output
swing of 5 V will have an amplitude range of 50 g peak.

Page 5
If a higher supply voltage is used (22 to 30 VDC), the amplitude range can be extended to 100 g peak. If a voltage
source lower than 18 V is used, the amplitude range will be lowered accordingly. Custom bias voltages are available
for lower or higher voltage supply applications.

Constant current diodes

Constant current diodes (CCDs) are required for two-wire internally amplified sensors. In most cases, they are
included in the companion power unit or monitor supplied. Generally, battery powered supplies contain a 2 mA CCD
to ensure long battery life. Line powered supplies (where power consumption is not a concern) should contain a 6 to
10 mA CCD when driving long cables. For operation above 100°C, where amplifier heat dissipation is a factor, limit
the current to less than 6 mA.

If the power supply does not contain a CCD for sensor powering, one should be placed in series with the voltage
output of the supply. It is important to ensure that proper diode polarity is observed.

High temperature piezoelectric vibration sensors

High temperature industrial sensors are available for applications up to 1400°F. Currently, high temperature sensors
are not internally amplified above 170°C (350°F). Above this temperature, sensors are unamplified (charge mode).
Charge mode sensors usually require a charge amplifier. The sensitivity of unamplified sensors should be chosen
to match the amplitude range of the amplifier selected. The unit of sensitivity for charge mode accelerometers is
expressed in picoCoulombs/g (pC/g). It is necessary to use special low noise, high temperature cables with charge
mode sensors to avoid picking up triboelectric noise–erroneous signals caused by cable motion.

It is recommended that a custom thermal isolation mount be used with amplified sensors for applications where the
frequency of interest is less than 5 kHz and the temperature is below 170°C.

Triaxial sensors

Many industrial customers use triaxial vibration sensors for multi-

directional machine monitoring and balancing. These devices contain
three mutually perpendicular sensors which give the user more
information about machine health than conventional single-axis units.
A triaxial sensor is also easier to mount than three separate single-axis
sensors.

Handprobes

Handprobes are handheld vibration sensors used to measure

vibration. Requiring no mounting, they are quick, easy to use,
and provide a good introduction to machine health monitoring.
Though their frequency response is limited compared to stud
mounted sensors, the information they provide can be very useful.
In conjunction with portable data loggers, handprobes are versatile
instruments for basic vibration analysis and trend monitoring.

Page 6
Summary

Vibration sensors are the initial source of information about machine condition, upon which productivity, product
quality and personnel safety decisions are based. It is crucial that sensors be properly selected and installed to
ensure reliable signal information. This technical note outlined some of the critical parameters that should guide
the selection of industrial vibration sensors. Following this process will increase the effectiveness of your vibration
monitoring program and improve productivity of plant personnel and equipment. The attached checklist may be used
to aid in the process of sensor selection.

Once the correct sensors have been chosen, they must be mounted on plant machinery. With a firm understanding
of the sensor requirements, capabilities, and limitations, the vibration analyst should have evaluated and determined
the mounting location of each sensor based upon the specific machine and vibration source to be monitored, as well
as the cabling requirements. Refer to Wilcoxon’s technical notes “Mounting considerations,” “Installation of vibration
sensors” and “Vibration sensor wiring and cabling” for more information on these topics.

Page 7
Sensor selection checklist

For assistance in selecting a vibration sensor, specific application and measurement requirements should be provided to
the application engineer. Completing the checklist below will help ensure that the proper sensor is chosen.

I) Describe the vibration measurement application (check all that apply):

 Pulp and paper  Automotive

 Petrochemical  Laboratory research
 Power plant  Microelectronics
 Oil exploration  Civil engineering
 Mining  Military
 Other _________

II) Please describe the dynamic measurement requirements of the application:

What is the approximate vibration amplitude level to be measured?

_________g peak, ______in/sec peak, ______mil peak
What is the maximum vibration amplitude level expected to be present?
_________g peak, ______in/sec peak, ______mil peak
What is the minimum vibration amplitude level of interest?
_________g peak, ______in/sec peak, ______mil peak
What is the maximum frequency of interest?
___________Hz, _________RPM
What is the minimum frequency of interest?
___________ Hz, _________RPM

III) Mechanical and chemical environment of the application:

What is the continuous temperature range? (min. to max.)

__________ to _________ ºC, __________ to _________ ºF
What is the intermittent temperature range? (min. to max.)
_________ to _________ ºC, __________ to _________ ºF
What is the expected humidity level? ________ % relative
What fluids contact the accelerometer? ______________________________________________
If submerged, what fluid pressure will be present? _________ psi
What high amplitude mechanical signals present? (i.e. steam valve release, gear chatter, impacts) __________________
_________________________________________________________________________________________________
What is the highest shock level expected to be present? ______________ g peak

What chemicals or gases contact the accelerometer or cable? (Check all that apply)

 Water (i.e. salt water, heavy water, steam) Describe: _________________________________________

 Halogens (i.e. chlorine, fluorine, halogenated compounds) Describe: ____________________________
 Gases (i.e. ozone, chemical fumes) Describe: _____________________________________________
 Acids (i.e. hydrochloric, sulfuric, nitric) Describe: ____________________________________________
 Bases (i.e. ammonia, caustic soda) Describe: ______________________________________________
 Solvents (i.e. MEK, Freon, Alcohol) Describe: ______________________________________________
 Fuels (i.e. gasoline, kerosene) Describe: __________________________________________________
 Oil (i.e. lubricating, crude) Describe: ______________________________________________________
 Other chemicals Describe: _____________________________________________________________

Page 8
IV) Electrical requirements and electrical environment of the sensor:

Is Intrinsically Safe operation required? (i.e. explosive environments) ____ yes (or) ____ no
What Power supply will be used? (18 - 30 Volt, 2 - 10 mA is usually recommended):
Manufacturer ____________________________
Model # ____________________________
Voltage Source ____________________________
Constant Current Source ____________________________(mA)
Is the machine grounded? ____ yes (or) ____ no
Is the sensor located near areas with electrostatic discharges? ____ yes (or) ____ no
Physical parameters and features of the sensor:
Sensor output: __ Acceleration __ Velocity __ Displacement
Physical design: __ Single axis __ Triaxial __ Ring shear mode
__ Handprobe
Special features: __ Temperature output __ Calibration circuit
Other:_______________________
Housing material: __ 316 stainless steel __ Titanium
__ Other_______________________
Desired characteristics:
Axial sensitivity ______________________mV/g
Frequency range to ______________________Hz
Resonance frequency ______________________kHz
Internal filtering requirements______________________________________________________
Maximum weight ______________________grams
Size limitation: h ______________ , l ______________ , w ______________

VI) Cabling requirements:

What cable lengths will be driven?

Cable length ________ft
Cable capacitance ________ pF/ft
Will the cable be near electromagnetic interference sources? (i.e. AC power lines, radio equipment, motors, and genera-
tors) ____ no (or) yes, describe:__________________________
Electrical connection: __ Connector __ Splash-proof __ Integral cable
Electrical connection location: __ Axial/top exit __ Radial/side exit
Cable type: __ Coaxial __ Two-conductor __ Dual shielded
Other_______________________
Other cable requirements:________________________________________________________
Reinforced cable:
Cable pull strength _____ lbs
Cable shielding _____ %
Other______________

VII) Mounting requirements (check request):

Mounting type: __ Detachable stud __ Integral stud __ Captive bolt

__ Adhesive __ Magnetic base
Thread size: __ 10-32 UNF __ 1/4-28 UNF
__ Other_______________________

VIII) Other specific requests or requirements: ____________________________________________________________

_________________________________________________________________________________________________
_________________________________________________________________________________________________
_________________________________________________________________________________________________

Page 9