Scribd
Upload
80 views2 pages

Inspection & Testing Plan For Polymer Modified Binders: INF-AP-QUA-ITP-03 Rev 0 Date:19.03.2018

This document outlines the inspection and testing plan for polymer modified binders. It lists the test parameters, applicable standards, specification limits, testing frequency, and responsibilities. Key tests include rotational viscosity, dynamic shear, solubility, rolling thin film oven residue properties, pressure aging vessel residue properties, creep stiffness, and direct tension failure strain. Testing will be performed on samples from each material source once every 450 tons of asphalt binder and when visible changes occur in the material.

Uploaded by

jerin sam kurian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
80 views2 pages

Inspection & Testing Plan For Polymer Modified Binders: INF-AP-QUA-ITP-03 Rev 0 Date:19.03.2018

This document outlines the inspection and testing plan for polymer modified binders. It lists the test parameters, applicable standards, specification limits, testing frequency, and responsibilities. Key tests include rotational viscosity, dynamic shear, solubility, rolling thin film oven residue properties, pressure aging vessel residue properties, creep stiffness, and direct tension failure strain. Testing will be performed on samples from each material source once every 450 tons of asphalt binder and when visible changes occur in the material.

Uploaded by

jerin sam kurian
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 2

INF-AP-QUA-ITP-03 Rev 0

Inspection & Testing Plan for Polymer Modified Binders Date:19.03.2018

Inspection & Test Details


Parameter Standard Specification Limits Testing
Frequency INF AP LAB TPL

Temperature, oC - As per Supplier Specifications Daily a

Average 7 Days Maximum Pavement Design Temperature, oC - <76 a

Minimum Pavement Design Temperature, oC - >-10 a

Flash Point, Cleaveland Open Cup, oC ASTM D92 230 a


Each Source, Visible changes in
Rotational Viscosity, Maximum 3 Pa.s, Test Temerature, oC ASTM D4402 135 Material, 1 test per 450 ton of a
Asphalt Binder
Dynamic Shear, G*/sin, Minimum, 1.00kPa, Test Temperature( oC)
ASTM D7175 76 a
at 10rad/s

Solubility, min% ASTM D5546 99 a

Separation Test:Absolute Difference between G*@76oC and 10


ASTM D7173 20 a
rad/s of Top & Bottom Specimens, Maximum, %
Requirements of the Rolling Thin Film Oven Residue (ASTM D2872)

Mass Loss, Maximum, % ASTM D2872 1 a

Dynamic Shear, G*/sin, Minimum, 1.00kPa, Test Temperature( oC) ASTM D7175 76
at 10rad/s a

Pressure Aging Vessel Residue (ASTM D6521)


Each Source, Visible changes in
PAV Aging Temperature, oC ASTM D6521 110 Material, 1 test per 450 ton of a
Asphalt Binder
Dynamic Shear, G*/sin, Minimum, 1.00kPa, Test Temperature( oC)
at 10rad/s ASTM D7175 37 a

Creep Stiffness, S, Maximum 300MPa and m-value, minimum


ASTM D6648 0 a
0.300 at 60 secs, test temperature, oC
Direct tension, failure Strain, Minimum, 1.0% (loading rate of 1.0
mm/min), test temperature oC ASTM D6723 0 a

ITP Name Position Date


Prepared By Jerin Sam Kurian QA/QC Inspector
Reviewed By Alfredo Marques QA/QC Manager

INF-AP-QUA-SF-ITP-03-01 Rev. 0 Date 19.03.2018


Approved By Alfredo Marques QA/QC Manager

INF-AP-QUA-SF-ITP-03-01 Rev. 0 Date 19.03.2018

You might also like