Operating Instructions CP600

Control Panels

CP620-x, CP620-WEB-x
CP630-x, CP630-WEB-x
CP635-x, CP635-WEB-x


Content
Introduction ........................................................................................................................ 2

Before You Start ................................................................................................................ 3

Safety Notices........................................................................................................................... 3

Markups .................................................................................................................................... 3

Product Overview .............................................................................................................. 4

Standards and Approvals ................................................................................................. 5

Product Identification............................................................................................................... 5

Technical Specifications .......................................................................................................... 6

Environmental Conditions ....................................................................................................... 6

Technical Data ................................................................................................................... 9

Dimensions ............................................................................................................................. 10

Installation Environment ........................................................................................................ 11

Applying the Gasket ............................................................................................................. 11

Installation Procedure ............................................................................................................ 12

Connections ..................................................................................................................... 14

Serial Port ............................................................................................................................... 15

Ethernet Port .......................................................................................................................... 15

Power Supply, Grounding and Shielding ...................................................................... 16

Battery .............................................................................................................................. 17

Cleaning Faceplates ........................................................................................................ 18

Getting Started ................................................................................................................. 19

System Settings ............................................................................................................... 20

Dedicated LED Indicators ............................................................................................... 22

Unpacking and Packing Instructions ............................................................................. 23

Operating Instructions 1 CP600/Issue: 12.2011

Introduction
The operational guidelines described below is information which relates to the device, place of employ-
ment, transportation, storage, assembly, use and maintenance.
The products have been designed for use in an industrial environment in compliance with the
2004/108/CE directive.
The products have been designed in compliance with:
 EN 61000-6-4
 EN 55011 Class A
 EN 61000-6-2
 EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6
The installation of these devices into the residential, commercial and light-industrial environments is al-
lowed only in the case that special measures are taken in order to get the conformity to IEC-61000-6.3.
The products are in compliance with the restrictions on Certain Hazardous Substances (RoHS) Directive
2002/95/EC.
This Operating Instruction describes the main features of the CP600 Control Panels. The Operating In-
structions refers to the following models:

Picture Type Description

CP620-x, CP620-WEB-x Operator interface with TFT color 4.3” display

touchscreen

CP630-x, CP630-WEB-x Operator interface with TFT color 5.7” display

touchscreen

CP635-x, CP635-WEB-x Operator interface with TFT color 7” widescreen

display touchscreen

Operating Instructions 2 CP600/Issue: 12.2011

Before You Start

Safety Notices
Indicates an imminent risk. It will lead to death or serious injury if not avoided.

DANGER!

Indicates a possible risk. It may lead to death or serious injury if not avoided.

WARNING!

Indicates a possible risk. It may lead to light or slight injury or material damage if not
avoided.
CAUTION!

Markups
 Enumeration.
 Precondition for an operation instruction or a description.
 Operation instruction with one step.
1. Operation instruction with several steps.
 Result of an operation.

Helpful information with background information or an emphasized notice.

NOTE

Application tips or other useful information and suggestions.

TIP

Operating Instructions 3 CP600/Issue: 12.2011

Product Overview
The Control Panels combine state-of-the-art features and top performance with an oustanding design.
They are the ideal choice for all demanding HMI applications including factory and building automation.
These Control Panels have been designed to run the PB610 Panel Builder 600 software.
 PB610 Panel Builder 600 Runtime included. Full compatibility with PB610 Panel Builder 600.
 Full vector graphic support. Native support of SVG graphic objects. Transparency and alpha blend-
ing.
 Full object dynamics: Control visibility and transparency, move, resize, rotate any object on screen.
Change properties of basic and complex objects.
 Truetype fonts.
 Multilanguage applications. Easily create and manage your applications in multiple languages to
meet global requirements. Far East languages are supported. Tools available in PB610 Panel Builder
600 support easy third-party translations and help reducing development and maintenance costs of
the application.
 Data display in numerical, text, bargraph, analog gauges and graphic image formats.
 Rich set of state-of-the-art HMI features: Data acquisition, alarm handling, scheduler and timed ac-
tions (daily and weekly schedulers, exception dates), recipes, users and passwords, e-mail and RSS
feeds, rotating menus.
 Includes support for a wide range of communication drivers.
 Multiple drivers communication capability.
 Remote monitoring and control. Client-Server functionality. Mobile clients supported.
 Offline and online Simulation with PB610 Panel Builder 600.
 Powerful scripting language for automating HMI applications. Script debugging improves efficiency in
application development.
 Rich gallery of vector symbols and objects.
 Project templates.
 Optional plug-in modules for fieldbus systems, I/O and controllers.

Operating Instructions 4 CP600/Issue: 12.2011

Standards and Approvals
The Control Panels have been designed for installation and use in an industrial environment in com-
pliance with the 2004/108/EC EMC Directive and with the following harmonized standards:
 EN 61000-6-4
 EN 61000-6-2
In compliance with the above regulations the products are CE marked.
The installation of these devices into the residential, commercial and light-industrial environments is al-
lowed only in the case that special measures are taken in order to get the conformity to EN 61000-6-3.

Product Identification
The Control Panel products are identified by a product label. The label reports several information, includ-
ing the model name, the part number, the power supply, the date of production (in the following format:
ywwy) and two barcodes. The first code is the version code, the second one the serial number (S.N.).

Example of product label

Information on type plate (example) Description

CP620 Product type

1SAP520200R0001 Product part number

1231 ywwy – week and year of production

09994971497 Serial number

040100A01000140 Version number of the product

WEB 1.5.15.117 Version number of the MicroBrowser (only valid for CP6xx-WEB)

Operating Instructions 5 CP600/Issue: 12.2011

Technical Specifications
Parameter Value

Touchscreen technology Resistive

Back-up battery 3V 50mAh Lithium, rechargeable, not user-replaceable, model VL2330

Fuse Automatic

Serial Port RS-232, RS-485, RS-422 software configurable

User memory Flash 128 MB

Recipe memory Flash

Hardware clock Clock/calendar with back-up battery

Accuracy RTC < 100 ppm

(at 25 °C operating)

Environmental Conditions
Parameter Value According to

Operating temperature 0 °C … +50 °C EN 60068-2-14

Storage temperature -20 °C … +70 °C EN 60068-2-14

Operating and storage humidity 5 % … 85 % RH not-condensing EN 60068-2-30

Vibrations 5 Hz … 9 Hz, 7 mm p-p EN 60068-2-6

9 Hz … 150 Hz, 1 g

Shock ± 50 g, 11 ms, 3 pulses per axis EN 60068-2-27

Protection class IP66 front panel * EN 60529

Touchscreen technology Resistive -

Touchscreen reliability > 1 million operations -

*) The front face of the Control Panel unit, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the table above. Even though the Control Panel unit’s level of resis-
tance is equivalent to these standards, oils that should have no effect on the Control Panel can possibly
harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cut-
ting oil are allowed to adhere to the unit for long periods of time. If the Control Panel’s front face protec-
tion sheet becomes peeled off, these conditions can lead to the ingress of oil into the Control Panel and
separate protection measures are suggested.
Also, if non-approved oils are present, it may cause deformation or corrosion of the front face. Therefore,
prior to installing the Control Panel be sure to confirm the type of conditions that will be present in the
Control Panel’s operating environment.
If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the
panel, the original level of the protection cannot be guaranteed. To maintain the original protection level,
be sure to replace the installation gasket regularly.

Operating Instructions 6 CP600/Issue: 12.2011

Electromagnetic Compatibility (EMC)
Test executed on the 230 V AC side of the Power Supply (EN 61000-4-11).

Parameter Value According to

Radiated disturbance test Class A EN 55011

Electrostatic discharge im- 8 kV (air electrostatic discharge) EN 61000-4-2

munity test 4 kV (contact electrostatic discharge)

Radiated, radio-frequency, 80 MHz … 1 GHz, 10 V/m EN 61000-4-3

electromagnetic field immuni- 1.4 GHz … 2 GHz, 3 V/m
ty test 2 GHz … 2.7 GHz, 1 V/m

Burst immunity test ± 2 kV DC power port EN 61000-4-4

± 1 kV signal line

Surge immunity test ± 0.5 kV DC power port (line to earth) EN 61000-4-5

± 0.5 kV DC power port (line to line)
± 1 kV signal line (line to earth)

Immunity to conducted dis- 0.15 … 80 MHz, 10 V EN 61000-4-6

turbances inducted by radio-
frequency field

Voltage dips, short interrup- Port: AC mains. Level:

tions and voltage variations 100 % / duration: 1 cycle and 250 cycles (50 Hz);
immunity test 40 % / duration: 10 cycles (50 Hz);
70 % / duration: 25 cycles (50 Hz);
Phase: 0°-180°

Operating Instructions 7 CP600/Issue: 12.2011

Durability Information
Parameter Value

Backlight service life (LED type) MTBF value: 40,000 hrs

(time of continuos operation until the brightness of the backlight
reaches 50 % of the rated value when the sorrounding temperature
1
reach 25 °C), see

Backlight service life (CCFL type) MTBF value: 50,000 hrs or more
(time of continuos operation until the brightness of the backlight
reaches 50 % of the rated value when the sorrounding temperature is
1
25 °C), see

Battery lifetime 10 years if the surrounding temperature is 25 °C

5 years if the surrounding temperature is 40 °C
1
1 year if the surrounding temperature is 50 °C, see

Front foil (without directly expose 10 years if the surrounding temperature is 25 °C

to sunlight or UV ray)

UV Resistance Indoor applications: After 300 hrs cycled humidity in QUV accelerated
weathering, some yellowing and brittleness may be present.
2
Touch panel 1,000,000 or more of activations, see
(resistive film, analog)

Touchscreen reliability > 1 million operations

1
Extended use in environments where the surrounding air temperature is 40 °C or higher may degrade
backlight quality/reliability/durability.
2
Solvent resistance:
Contact for ½ hour at 21 °C, no visible effect: Acetone, Butyl Cellosolve, Cyclohexanone, Ethyl Acetate,
Hexane, Isopropyl Alcohol, MEK, Methylene Chloride, Toluene, Xylene
Contact for 24 hours at 49 °C, no visible effect: Clorox, Coffee, Downy, Fantastik, Formula 409, Ketchup,
Lemon Juice, Mr. Clean, Mustard (slight yellow stain), Spray ‘N Wash, Tea, Tomato Juice, Top Job, Wisk

Operating Instructions 8 CP600/Issue: 12.2011

Technical Data

Model CP620(-WEB)-x CP630(-WEB)-x CP635(-WEB)-x

Display/Backlight TFT Color / LED TFT Color / LED TFT Color / LED

Colors 64 K 64 K 64 K

Resolution 480 x 272 320 x 240 800 x 480

Diagonal (inches) 4.3” 5.7“ 7“ widescreen

Dimming Yes Yes Yes

Touchscreen Yes Yes Yes

User memory flash 128 MB 128 MB 128 MB

SC card slot Yes Yes Yes

Recipe memory Yes. Flash memory Yes. Flash memory Yes. Flash memory
storage limited only by storage limited only by storage limited only by
available memory available memory available memory

Serial Port RS-232, RS-485, RS-232, RS-485, RS-232, RS-485,

RS-422, software RS-422, software RS-422, software
configurable configurable configurable

Ethernet port 2 x 10/100 Mbit/s with 2 x 10/100 Mbit/s with 2 x 10/100 Mbit/s with
integrated switch integrated switch integrated switch

USB port 1 x host interface, 2 x host interface, 2 x host interface,

version 2.0 version 2.0 version 2.0

Expansion slot 1 x optional plugin 2 x optional plugin 2 x optional plugin

Battery Rechargeable Rechargeable Rechargeable

Real-time clock Yes Yes Yes

Voltage 18-30 V DC 18-30 V DC 18-30 V DC

Current rating (at 24 V DC) 0.4 A 0.65 A 0.7 A

Weight 1 kg 1 kg 1 kg

Operating Instructions 9 CP600/Issue: 12.2011

Dimensions

Model A B C H L

mm inches mm inches mm inches mm inches mm inches

CP620(-WEB)-x 136 5.35” 96 3.78” 52 2.04” 107 4.21” 147 5.78”

CP630(-WEB)-x 176 6.90” 136 5.35” 45 1.77” 147 5.79” 187 7.36”

CP635(-WEB)-x 176 6.90” 136 5.35” 47 1.85” 147 5.79” 187 7.36”

Model CSD: Minimum compass safe dis- CSD2: Minimum compass safe distance
tance of standard compass of steering compass, standby steering
compass and emergency compass

mm inches mm inches

CP620(-WEB)-x 350 13.78 200 7.87

CP630(-WEB)-x 350 13.78 200 7.87

CP635(-WEB)-x 450 17.74 250 9.84

Operating Instructions 10 CP600/Issue: 12.2011

Installation Environment
The equipment is not intended for continuous exposure to direct sunlight. This might accelerate the aging
process of the front panel film.
The equipment is not intended for installation in contact with corrosive chemical compounds. Check the
resistance of the front panel film to a specific compound before installation.
Do not use tools of any kind (screwdrivers etc.) to operate the touchscreen of the panel.
In order to meet the front panel protection classifications, proper installation procedure must be followed:
 The borders of the cutout must be flat.
 The cutout for the panel must be of the dimensions indicated in this manual.
 Screw up each fixing screw until the plastic bezel corner get in contact with the panel.
The IP66 is guaranteed only if:
 Maximum deviation from the plane surface to the cut-out: Ø 0.5 mm
 Thickness of the plate the equiment is mounted: 1.5 mm to 6 mm
 Maximum surface roughness where the gasket is applied: Ø 120 µm

Applying the Gasket

 Apply the gasket on the rear of the frame.

A Gasket B Installation cut-out

Operating Instructions 11 CP600/Issue: 12.2011

Installation Procedure
 Place the fixing brackets.

Screw each fixing screw until the bezel corner gets in contact with the panel.

CAUTION!

Operating Instructions 12 CP600/Issue: 12.2011

Communication Cable
The communication cable must be chosen for the type of device being connected.

Connection to an AC-500 with the TK681 CP600-AC500 RS232 communication cable

Connection to an AC-500(-eCo) with the TK682 CP600-AC500-eCo RS485 communication cable

*) all resistors: 0.25 W

1 Shield 2 SubD9 male

Operating Instructions 13 CP600/Issue: 12.2011

Connections

1 USB port 3 Serial port 5 Expansion slot for plugin module

2 Power 4 Ethernet port 6 SD card slot

Operating Instructions 14 CP600/Issue: 12.2011

Serial Port
The serial port is used to communicate with the PLC or with another type of controller.
Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422,
RS-485.

It is always necessary to use the correct cable type to connect on the PLC.
If the proper cable is not used, communication with the PLC will not be possible.
NOTE

The serial port is software programmable. Make sure you select the appropriate interface in the pro-
gramming software.

Serial port.

RS-232 RS-422, RS-485

Pin Description Pin Description

1 GND 1 GND

2 2

3 TX 3 CHA-

4 RX 4 CHB-

5 5

6 +5 V output 6 +5 V output

7 CTS 7 CHB+

8 RTS 8 CHA+

9 9

The communication cable must be chosen for the type of device being connected.

Ethernet Port
The Ethernet port has two status indicators.

Ethernet Port

A OFF: No activity B ON: Valid link hast NOT been detected

BLINKING: Activity OFF: Valid link has been detected

Operating Instructions 15 CP600/Issue: 12.2011

Power Supply, Grounding and Shielding

DC Power Connector, Female - R/C Terminal Blocks (XCFR2), manufactured by Weidmüller Inc.,
Cat. No. BLZ 5.08, torque 4.5 lb-in

Ensure that the power supply has enough power capacity for the operation of the equipment.

NOTE

The unit must always be grounded to earth. Grounding helps limit the effects of noise due to electromag-
netic interference on the control system.
1. Do the earth connection using either the screw or the faston terminal located near the power supply
terminal block. A label helps identify the ground connection.
2. Connect to ground the terminal 3 on the power supply terminal block.
3. The power supply circuit may be floating or grounded. In the latter case, connect to ground the power
source common as shown in the figure below with a dashed line.
When using the floating power scheme, note that the panes internally connects the power common to
ground with a 1 MΩ resistor in parallel with a 4,7 nF capacitor.
The power supply must have double or reinforced insulation.

Suggested wiring for the power supply.

All the electronic devices in the control system must be properly grounded. Grounding must be performed
according to applicable regulations.

Operating Instructions 16 CP600/Issue: 12.2011

Battery
The Control Panels are equipped with a rechargeable lithium battery, not user-replaceable.
The battery maintains the hardware real-time clock (date and time).

Charging the Battery

 At first installation recharge the battery for 48 hours.

 When the battery  is charged, it assures a period of 3 month of data back-up at 25 °C.

Recycling and Disposal

The battery must not be disposed as unsorted domestic waste.

 Dispose the battery according to the local regulations.

Operating Instructions 17 CP600/Issue: 12.2011

Cleaning Faceplates
The equipment must be cleaned only with a soft cloth and neutral soap product. Do not use solvents.

Operating Instructions 18 CP600/Issue: 12.2011

Getting Started
The Control Panels must be programmed with the programming package PB610 Panel Builder 600.
The Control Panels are programmed via the Ethernet interface.
 The Control Panel must be in configuration mode to be programmed.
 To program a Control Panel connect the Control Panel to a PC running PB610 Panel Builder 600
software package.
TM
The software package PB610 Panel Builder 600 is a Windows application and must be properly in-
TM
stalled. The Windows environment is not included in the software package PB610 Panel Builder 600
and must already be installed on the PC.
PB610 Panel Builder 600 uses the PC Ethernet interface to communicate with the target device.
 Make sure that the proper firewall policy is configured in order to allow PB610 Panel Builder 600 to
access the network.
The version of the Panel Builder used must be compatible with the PB610 Panel Builder 600 Runtime
version installed on the Control Panel to be programmed. Check with technical support for more informa-
tion on compatibility between firmware and programming software.

Operating Instructions 19 CP600/Issue: 12.2011

System Settings
The Control Panels have a system settings tool to allow basic and preliminary settings to the unit.

System settings tool

The system settings tool is a rotating menu.

 Use the navigation buttons Next and Back to scroll between the available options.
 On the left side the selected component and function are highlighted.

 On the right side, on the “Info” pane, the information about the selected option is shown.
For example the version of the Main OS component.

The system settings tool has two operating modes: User Mode and System Mode. The difference be-
tween them is the number of available options.
System settings in User Mode is activated from the contextual menu, accessible by clicking and holding
any unused area on the touchscreen for a few seconds. Default holding time is 2 sec. This is a runtime
parameter that could have been changed.
System settings in System Mode can be activated with the so-called emergency system access proce-
dure. This procedure consist in tapping in the middle of the touchscreen with a finger at a high frequency
while the systemis powering up. The emergency procedure can only be accessed at powerup.

User Mode
User Mode is the simplest possible interface where a generic user can get access to the basic settings of
the panel:
 Calibrate Touch: allows to calibrate the touchscreen interface
 Network: allows to change the options of the panel on-board network card
 Time: allows to change the panel RTC options, including time zone and DST
 Display settings: automatic backlight turnoff and brightness adjustment
 BSP settings: allows to check the BSP (Board Support Package) version (example 2.37), check the
operating hours timers for the unit and separately for the backlight, enable/disable the buzzer, ena-
ble/disable the use of the “low battery” front LED indicator

Operating Instructions 20 CP600/Issue: 12.2011

System Mode
 System Mode is the complete interface of the system settings tool where all options are available.
Additionally to the options of the User Mode the following options are available:
 Format Flash: allows to format the internal panel flash disk
 Resize Image Area: allows to resize the flash portion reserved to store the splash screen image dis-
played by the unit at power up; default settings are normally ok for all the units
 Download Configuration OS: allows to check current version and upgrade the back-up operating sys-
tem, see below in the next chapter for additional details
 Download Main OS: allows to check current version and upgrade the main operating system, see be-
low in the next chapter for additional details
 Download Splash Image: allows changing the splash screen image displayed by the unit at power
up; the image should be provide in a specific format. We suggest to update Splash Screen Image di-
rectly from Studio software which supports this feature starting from V 1. 50
 Download Bootloader: allows to check current version of the system boot loader and to upgrade it,
see below for additional details
 Download Main FPGA: allows to check current version and upgrade the main FPGA firmware, see
below for additional details
 Download Safe FPGA: allows to check current version and upgrade the back-up (safe) copy of the
FPGA Firmware, see below for additional details
 Download System Supervisor: allows to check current version and upgrade the system supervisor
firmware responsible for RTC and power supply handling, see below for additional details

Operating Instructions 21 CP600/Issue: 12.2011

Dedicated LED Indicators
There is one LED in the upper left part of the front below the red stripe. The meaning of the LED indicator
is explained in the following table:

LED color Status Meaning

Red Blinking Battery low or alarm requires acknowledgment

On Hardware fault

Green Blinking Communication error

On Normal operation

Operating Instructions 22 CP600/Issue: 12.2011

Unpacking and Packing Instructions

 To repack the unit follow the instructions backwards.

Operating Instructions 23 CP600/Issue: 12.2011

 Manual No. 2CDC159005M0202


ABB Automation Products GmbH
Wallstadter Str. 59
68526 Ladenburg, Germany
Telephone +49 (0 ) 6221 701-1444
Telefax +49 (0 ) 6221 701-1382
E-Mail [email protected]
Internet http://www.abb.com/PLC