ACC ELERAT ED M ACHI NI NG

General Catalog
2018 / 2019
In an accelerated world, a quick response to market needs is
necessary. As a pioneer in innovation, Tungaloy leads the market
in developing unique and powerful grades and geometries for this
new era. TUNGFORCE, our newest line of products is designed for
accelerated machining, bringing you the newest and greatest
solutions for your machining needs.
 2018 / 2019
f ull p ro duc t l i ne

www.tungaloyamerica.com
Grade A
C o ate d G rade CV D A002
C o ate d G rade P V D A003
Ce ramic A005
C e r m et A005
CBN ( T- CBN) A006
PCD ( T-DIA) A007
Uncoated Cemented Ca rbide A007

Tur nLine B
Inse r t B002
E x te rnal Toolholder B182
Inte rnal Toolholder B280
Miniature Machining B348
T hre ading B410

G roove Line C
Pa r ting, Grooving, and Groove -Turn system C 002

MillLine D
High-Fe e d Milling D002
Shoulde r Milling D032
Fac e Milling D096
Slot Milling D126
Prof ile Milling D140
Multi-Functional Milling D168
Milling Inse r t D212

D rillLine E
2 Ef fe c ti ve D r ill E004
Indexa ble D r ill E066
De e p Hole D r ill E096

ToolLine F
Tooling S yste m F002

Use r´s Guide G

Pa r ts for Tool G002
Te chnic al Refe re nce G029
A lphanumeric Index G084

Tungaloy
 I n t r o d u c t io n
■ Icons along the right/left side of the page

Turning Grooving, turning, and parting-off

Ext. toolholder Int. toolholder Miniature tool Threading tool Grooving, Ext. grooving Int. grooving Face grooving Parting-off
turning, and
parting-off tool

Milling

High-feed milling Shoulder milling Face milling Slot milling Profile milling Multi-functional
milling

Drilling Tooling system

2-effective drill Indexable drill Deep hole drill Tooling system

■ Icons in the chart section for each product

Threading

Ext. threading Int. threading

Grooving

Ext. grooving Ext. grooving Ext. grooving Ext. grooving Forming Int. grooving Int. grooving Int. grooving and Int. grooving Parting-off
and turning (full R) and turning and turning turning (full R) (full R)
(full R)

Face grooving Face grooving Int. face Int. face grooving Face grooving
and turning grooving and turning for shaft

Milling

R R R
Shoulder milling Deep shoulder Shoulder milling Face milling Slotting Slotting (with Side slotting Side milling Pocketing Ramping
milling (with radius) radius)

Profiling Plunging Hole enlarging Holemaking Counterboring Hole chamfering Chamfering Cutting-off

Drilling
KITS

Drilling Small-diameter Deep-hole Hole chamfering Tool kit Oil hole Oil hole for high-
drilling drilling pressure

www.tungaloyamerica.com
 I n t r o d u c t io n
■ Note in using this catalog:
★ This catalog provides the information of Tungaloy’s cutting tools as of September 2017.
★ The specifications are subject to change without prior notice for product improvements. Also, the products may
  be discontinued in the future due to the development of new products.
★ The dimensions of all products are shown in inch (in) and millimeters (mm) where applicable.
★ For indexable tools, such as toolholders, cutters, drill bodies, applicable inserts or heads need to be ordered
  separately.
■ How to find a tool:
★ The catalog classifies the cutting tools into 5 lines – TurnLine (turning tools), GrooveLine (grooving tools),
  MillLine (milling tools), DrillLine (drilling tools), and ToolLine (tooling systems). The tools in each line are
  categorized by the applications.

Product photo Page number

MillLine - High-Fe ed Milling
Inch Metric

D004
EXH
High-feed endmills
ø0.394" - ø0.625" (ø10 - ø16 mm)
20° max. ap 0.031" (0.8 mm)

D008
Super high-feed milling cutters with 4-cornered double-sided inserts
ø0.625" - ø6.000"
15° max. ap 0.059" Tool’s feature and specification
D 016
Super high-feed cutters for profile milling with rigid clamping
ø1.000" - ø2.000"
20° max. ap 0.157"

D 021
Super high-feed cutters for face milling with 8-cornered double-sided inserts
ø2.000" - ø6.000"
13° max. ap 0.079"

D 024
Super high-feed milling cutters for large depths of cut

14° ø2.500" - ø6.000"

max. ap 0.098"

TXP
D 02 6
High-feed milling cutters with single-sided inserts
10°-20° ø0.750" - ø6.000"
max. ap 0.118"

D002 www.tungaloyamerica.com

Example: Contents of the cutters for high-feed milling in MillLine

★ Alphanumeric index in User’s Guide helps you search a specific product.

■ How to read the list for the standard items:

★ Designations for indexable tools – toolholders, cutters, drill bodies, etc.
· Orders are to be received for the tools with the designations in the catalog.
· For the tool with right- and left-hand options, the designation includes **R/L** as shown below.
Ex. 1: Designation: A12-SCLCR/L3-D16
You can order both right- and left-hand tools. A12-SCLCR3-D16 (a right-hand tool) and
A12-SCLCL3-D16 (a left-hand tool) will be available.
Ex. 2: Designation: E10-SCLCR3-D14
You can order only right-hand tools. Please contact us when you need left-hand tools.
★ Line-up for inserts and solid tools
Blank : Please contact us regarding the product.

Tungaloy
 Grade

www.tungaloyamerica.com
GR ADE

Coated Grade CV D A0 02

C oate d G rade P V D A0 03

Ceramic A0 05

Cer met A0 05

CBN ( T-CBN) A0 0 6

PCD ( T-DI A) A0 07

Uncoated Cemented Ca r bide A0 07

Tungaloy A001
Grade
CVD - Coated Grade
Coating

Grooving
Turning

Drilling
Milling
Grade Main Thickness Application Feature
composition / μm

T9105 - Good wear resistance

P01 - P10 TiCN-Al2O3 16
- Excellent performance in high-speed cutting
K10 - K20

T9115 - Well-balanced between wear and chipping resistance

P10 - P20 TiCN-Al2O3 16
- Suitable for a wide range of turning applications
K15 - K30

T9125 TiCN-Al2O3 16
- High chipping resistance in light to medium interrupted cutting
P20 - P30 - First choice for machining steel

T9135 TiCN-Al2O3 16 - Excellent fracture resistance in heavy interrupted cutting

P30 - P40

T6120
P10 - P20 TiCN 6 - Good wear resistance in continuous cutting at high speed
M10 - M20

T6130 - High wear resistance in cutting at medium to high speed

P15 - P30 TiCN 6
- First choice for machining stainless steel
M15 - M30

T515 TiCN-Al2O3 16
- Good wear resistance even in high-speed machining
K10 - K20 - First choice for roughing cast iron

T5105 TiCN-Al2O3 16 - High resistance to wear and plastic deformation in continuous cutting at high speed
K05 - K15

T5115 TiCN-Al2O3 16
- Stable machining in a wide range of applications from continuous to interrupted
K10 - K20 cutting

T5125 TiCN-Al2O3 16
- Strong resistance to sudden fracture
K15 - K30 - Ideal for heavy interrupted machining

T313V TiCN-Al2O3 3 Threading

- Good resistance to plastic deformation
- - Designed for threading

T3225 - High chipping and fracture resistance

P20 - P35 TiCN-Al2O3 10
- Suitable for machining steel and stainless steel
M20 - M35

T3130 - Good balance between wear and chipping resistance

P20 - P40 TiCN-Al2O3 6
- Ideal for machining steel and stainless steel
M20 - M40

T1215 TiCN-Al2O3 10
- Good balance between wear and chipping resistance
K10 - K25 - Designed for machining cast iron

T1115 TiCN-Al2O3 11
- High wear resistance
K10 - K25 - Ideal for machining cast iron

A002 www.tungaloyamerica.com
PVD - Coated Grade

Grade
Coating

Grooving
Turning

Drilling
Milling
Grade Main Thickness Application Feature
composition / μm

AH110
P05 - P15
- High wear resistance
M05 - M15 (Ti, Al)N 3
- Suitable for finishing steel, cast iron, and high-hardened material
K10 - K25
S05 - S15

AH120
P15 - P25 - Good balance between wear and fracture resistance
M15 - M25 (Ti, Al)N 3 - Suitable for machining steel, stainless steel, cast iron, and super alloys under general
K15 - K30 cutting conditions
S10 - S25

AH130 - High chipping and fracture resistance

P25 - P40 (Ti, Al)N 3
- Designed for machining austenitic stainless steel under general cutting conditions
M25 - M40

AH140 (Ti, Al)N 3

- High fracture resistance
M30 - M45 - Suitable for machining stainless steel

AH170
P20 - P35 - High wear resistance
(Ti, Al)N 3
M20 - M35 - Suitable for steel and cast iron drilling
K15 - K30

AH180
P20 - P35 - High wear resistance
(Ti, Al)N 3
M20 - M35 - Suitable for steel, cast iron and stainless drilling
K15 - K30

AH330 (Ti, Al)N 3 - Excellent wear resistance

P15 - P30

AH630 - Good resistance to wear and fracture in machining stainless steel at low to medium
P15 - P30 (Ti, Al)N 5
cutting speed
M15 - M30

AH645
P30 - P40 (Ti, Al)N 5 - High fracture resistance in machining stainless steel
M30 - M40

AH710
P05 - P15 - High wear resistance
(Ti, Al)N 3
K05 - K15 - Ideal for finishing steel, cast iron and high-hardened material
H05 - H15

AH725
P15 - P30
- Good balance between wear and chipping resistance
M15 - M30 (Ti, Al)N 2
- Suitable for machining steel and stainless steel under general cutting conditions
K25 - K30
S15 - S25

AH7025
P20 - P30 - Excellent wear resistance and high rigidity
(Ti, Al)N 3.5
M20 - M30 - First choice for grooving of various materials
S15 - S25

AH730 (Ti, Al)N 3 - Well-balanced between wear and fracture resistance

P15 - P30

AH740 (Ti, Al)N 3 - Excellent chipping resistance in machining steel

P25 - P40

AH750 (Ti, Al)N 3

- High wear resistance
H15 - H30 - Suitable for hard material machining

AH8005 - Good balance between wear and fracture resistance

M01 - M10 (Al,Ti)N 3.5
- First choice for machining heat-resistant alloys under general cutting conditions
S01 - S10

AH8015
M10 - M20 (Al,Ti)N 3.5 - Strong resistance to wear and built-up edge
S10 - S20

AH905 (Al, Ti)N 1.5 - Strong resistance to wear and built-up edge
S01 - S10

Tungaloy A003
Grade
PVD - Coated Grade
Coating

Grooving
Turning

Drilling
Milling
Grade Main Thickness Application Feature
composition / μm

AH3035 - Good balance between wear and chipping resistance

P20 - P45 (Ti, Al)N 5
- Suitable for machining high-hardened material at high feed
H20 - H30

AH3135 - High fracture resistance

P30 - P40 (Ti, Al)N 4
- Ideal for machining steel and stainless steel under general cutting conditions
M30 - M40

AH4035 (Ti, Al)N 5

- Good balance for wear and fracture resistance
M30 - M45 - Suitable for difficult stainless steel machining

AH6030 - High fracture resistance

M25 - M35 (Ti, Al)N 5 - Ideal for drilling stainless steel and heat-resistant alloys under general cutting
S15 - S30 conditions

AH9030 - High wear resistance

P15 - 35 (Ti, Al)N 5
- Designed for drilling steel and cast iron at high speed
K10 - 25

SH725 - Excellent wear resistance

P20 - P30 (Ti, Al)N 2
- Suitable for machining steel and stainless steel
M20 - M30

SH730
P20 - P35 - High wear resistance
(Ti, Al)N 1
M20 - M35 - Suitable for machining steel, stainless steel, and difficult-to-cut materials
S05 - S15

GH110
K10 - K25 Ti(C, N, O) 3 - Good wear resistance
N05 - N15

GH130
P25 - P40 - High chipping and fracture resistance
Ti(C, N, O) 3
M25 - M40 - Suitable for machining steel, stainless steel and cast iron
K25 - K40

GH330
P15 - P30 - Strong resistance to wear and fracture
Ti(C, N, O) 3
M15 - M30 - Suitable for continuous to medium interrupted cutting
K05 - K30

GH730
P20 - P35 - High wear resistance
Ti(C, N, O) 3
M20 - M35 - Ideal for turning and grooving at low speed
K20 - K30

J740 For small

TiN 1 - Ultra-fine-grain cemented carbide coated with TiN-based compound
- lathes

YH170 - Strong resistance to wear and fracture

P20 - P35 Ti(C, N) 1.5
- Suitable for steel and stainless drilling
M20 - M35

YH180 - High wear resistance

P20 - P35 Ti(C, N) 1.5
- Suitable for steel and stainless drilling
M20 - M35

JM10 - High wear resistance

P20 - P35 TiN 1
- Suitable for steel and stainless drilling
M20 - M35

DS1100 DLC coating

Thin - High wear resistance
N05 - N20 layer - Designed for finishing aluminum

DS1200 DLC coating

Thin - Good balance between wear and chipping resistance
N10 - N25 layer - Ideal for semi-finishing to finishing of aluminum

A004 www.tungaloyamerica.com
Cer a mic

Grade
Grooving
Hard-

Turning
Specific T.R.S.

Drilling
Milling
Grade ness Application Feature
gravity (GPa)
(HRA)

- Alumina base
LX11 4.35 94.0 0.9
- Suitable for continuous cutting of high-hardened materials

- Alumina base
LX21 4.24 94.0 0.8
- Excellent chipping resistance in continuous cutting of cast iron

- Silicon nitride base

FX105 3.24 93.0 1.3
- Suitable for high-speed machining of cast iron

- Silicon nitride base

CX710 3.20 92.9 1.1
- Excellent performance in high-speed machining of cast iron

Cer met
Coating

Grooving
Turning

Drilling
Milling
Grade Main Thickness Application Feature
composition / μm

- High wear resistance

GT9530 Ti(C, N, O) 3
- Ideal for finishing with high surface quality

For small
J9530 TiN 1 - Suitable for small-part machining
lathes

- High fracture resistance

NS9530 Uncoated -
- Suitable for finishing to medium cutting of steel

- Good resistance to fracture and thermal crack

NS740 Uncoated -
- Ideal for milling operations that require high rigidity

NS520 Uncoated - - Good wear resistance

GT720 Ti(C, N, O) 3 - Good wear resistance in high speed machining

X407 Uncoated - - Good wear resistance for finish on dry machining

N308 Uncoated - - Good wear resistance

Tungaloy A005
Grade
CBN ( T- CBN)

Grooving
Turning
Hardness T.R.S.

Drilling
Milling
Grade Application Feature
(Hv) (GPa)

BXA20 3300 ~ 3500 1.30 ~ 1.50 - Excellent performance in machining hardened steel

BXM10 2700 ~ 2900 0.80 ~ 0.90 - Suitable for machining hardened steel with continuous cutting at high speed

BXM20 3500 ~ 3700 1.35 ~ 1.50 - First choice for machining hardened steel in a wide range of applications

BXC50 3500 ~ 3700 1.15 ~ 1.30 - High fracture resistance in continuous to interrupted machining

- Good wear resistance

BX310 2700 ~ 2900 0.80 ~ 0.90
- Designed for continuous cutting of hardened steel at high speed

- Excellent sharpness
BX330 2800 ~ 3000 0.85 ~ 0.95
- Designed for finishing hardened steel

BX360 3200 ~ 3400 1.00 ~ 1.10 - Suitable for general-purpose machining of hardened steel

- High fracture resistance

BX380 3500 ~ 3700 1.15 ~ 1.30
- Suitable for heavy interrupted cutting of hardened steel

BX530 2800 ~ 3000 0.85 ~ 0.95 - Suitable for finishing hardened steel with high surface quality

BXC90
3900 ~ 4100 1.80 ~ 1.90 - Suitable for machining cast iron at high speed
(BX90S)

- Excellent wear resistance in high-speed machining

BX910 2600 ~ 2800 0.80 ~ 0.90
- Ideal for machining centrifugally cast iron

BX930 3000 ~ 3200 0.95 ~ 1.20 -Designed for machining ductile cast iron

- High fracture resistance

BX950 3900 ~ 4100 1.80 ~ 1.90
- Good performance in high-speed machining

BX850 3300 ~ 3500 0.75 ~ 0.85 - Suitable for hardened steel ball end milling

- High wear resistance

BX870 3000 ~ 3200 0.95 ~ 1.20
- Suitable for machining cylinder liners made of cast iron

Sintered - Excellent sharpness

BX470 4100 ~ 4300 1.90 ~ 2.10
- Suitable for machining ferrous sintered metal
metal

Sintered - Hardest grade of all T-CBN grades

BX480 4100 ~ 4300 1.90 ~ 2.10
- Suitable for machining ferrous sintered metal
metal

- High wear resistance and thermostability

M714B 3000 ~ 3200 1.00 ~ 1.10
- Good performance in high-speed machining of Inconel

A006 www.tungaloyamerica.com
PCD ( T- DIA )

Grade
Grooving
Grain Hard-

Turning

Drilling
T.R.S.

Milling
Grades size ness Application Feature
(GPa)
(μm) (Hv)

- Excellent sharpness for high surface quality

DX110 <1 8500 1.8
- Suitable for finishing non-ferrous metal and nonmetal

DX120 4.5 9000 1.8 - Suitable for precision machining of non-ferrous metal and nonmetal

- High wear resistance

DX140 12.5 10000 1.7
- Suitable for machining non-ferrous metal and nonmetal

DX160 28 11000 1.6 - Designed for machining ceramic, cemented carbide, and nonmetal

- High wear resistance

DX180 45 12000 1.5
- Designed for ceramic, cemented carbide, and nonmetal

Uncoate d Cemente d Ca r bide

Grooving

Grooving
Hard- Hard-
Turning

Turning
Specific T.R.S. Specific T.R.S.
Drilling

Drilling
Milling

Milling
Grades ness Application Grades ness Application
gravity (GPa) gravity (GPa)
(HRA) (HRA)

UX30 UM
P30 12.6 91.1 2.3 K10 - K25 13.9 90.9 3.5
M30 N10 - N25

TH10 G2
P10 K10 - K25 15 90.8 2.7
M10 14.7 92.0 2.4 N10 - N25
K10
N10 G1F
P10 - P25 15.1 92 2.6
KS05F K10 - K25
K05
15.0 93.0 2.9 MD10
S05
P10 - P25 15 92.8 3.4
N05
M10 - M25
KS15F 14.4 91.5 3.0 MD20
N15 P20 - P35 14.4 91.5 3.9
M20 - M35
KS20
K20
14.5 90.8 2.8
N20
S20

TH03
P05
M05 13.8 93.8 1.9
K05
N05

F 14.9 93.4 2.5

EM10
P10 - P25 14 91.5 3.4
K10 - K25

Tungaloy A007
 TurnLine

www.tungaloyamerica.com
TURNING

Inser t B 0 02

E x ter nal Toolholder B182

Inter nal Toolholder B280

Miniature Machining B348

T hreading B410

Tungaloy B001
Tur nLine - Inse r t
Inch Metric

Negative type B 0 52
Coated grades CVD/PVD, Cermet, Uncoated cemented carbides, Ceramic

Posivite type B10 6

Coated grades CVD/PVD, Cermet, Uncoated cemented carbides, Ceramic

CBN/PCD Insert B16 0

CBN (T-CBN), PCD (T-DIA)

B002 www.tungaloyamerica.com
Tungaloy B003
Insert Tur n L i n e - S y m bolization of Inserts

B004 www.tungaloyamerica.com
ANSI Designation

Insert
B007.

Tungaloy B005
Insert Tur n L i n e - D e s i gnation system for Inse r t
 Conforms to “Indexable Inserts for Cutting Tools - Designation” (JIS B4120-1998, and ISO 1832 / AM1-1998)
Nose angle Symbol Tolerance (mm)
Symbol Shape (degree) Figure
(class) Corner height (m) Thickness (s) I. C. dia. (ød)
H Hexagonal 120°
Octagonal A ±0.005 ±0.025 ±0.025
O 135°
F ±0.005 ±0.025 ±0.013
P Pentagonal 108° Symbol Relief angle
C ±0.013 ±0.025 ±0.025
S Square 90° A 3°
H ±0.013 ±0.025 ±0.013
T Triangular 60° B 5°
E ±0.025 ±0.025 ±0.025
C 80° C 7°
G ±0.025 ±0.13 ±0.025
D 55° D 15°
±0.005 ~
E Rhombic 75° E 20° J ±0.005 ±0.025
±0.13
F 50° F 25° ±0.05 ~
K ±0.013 ±0.025
G G-shape (Tungaloy’s symbol) 70° G 30° ±0.13
M 86° N 0° ±0.05 ~
L ±0.025 ±0.025
Rhombic ±0.13
V 35° P 11°
Y-shape (Tungaloy’s symbol) ±0.08 ~ ±0.05 ~
Y 25° O Others M ±0.13
±0.18 ±0.13
W Trigon 80° X Special
±0.08 ~ ±0.05 ~
L Rectangular 90° N ±0.025
±0.18 ±0.13
A 85° ±0.13 ~ ±0.08 ~
U ±0.13
B Parallelogram 82° ±0.38 ±0.25
K 55° 2 Relief angle 3 Accuracy

R Round - 1 2 3 4 5
1 Shape
Notes : With respect to the nose
angles of rhombic and
parallelogram shaped
inserts, use the smaller
angle respectively.
[Example]

[Example]
T N M G 16
C C G T 09
1 2 3 4 5

4 Groove and hole 5 Cutting edge length

Symbol Hole Shape of hole Chip-
breaker Shape * I. C.dia.
(mm)
N Without Symbol Length Symbol Length Symbol Length Symbol Length Symbol Length Symbol Length Symbol Length Symbol Length

Single- 03 3.97 03 4.0 06 6.9 04 4.8 3.97

R Without - sided
Double- 04 4.76 04 4.8 08 8.2 05 5.8 08 8.3 4.76
F sided
*05 5 - - - - - - - - - - - - - - 5
A Without
05 5.56 05 5.6 03 3.8 09 9.6 06 6.8 5.56
Cylindrical Single- -
M sided
*06 6 - - - - - - - - - - - - - 6
hole
Double- 06 6.35 06 6.5 04 4.3 11 11 07 7.8 11 11.2 6.35
G sided
07 7.94 08 8.1 05 5.4 13 13.8 09 9.7 7.94
W Partly cylindrical
hole, single-side
Without
*08 8 - - - - - - - - - - - - - - 8
40° ~ 60° Single-
T Counter sink sided 09 9.525 09 9.525 09 9.7 06 6.5 16 16.5 11 11.6 16 16.6 16 19.7 9.525
*10 10 - - - - - - - - - - - - - - 10
Q With Partly cylindrical
hole, double-side
Without
40° ~ 60° *12 12 - - - - - - - - - - - - - - 12
Double-
U Counter sink sided 12 12.7 12 12.7 12 12.9 08 8.7 22 22 15 15.5 22 22.1 12.7
B Partly cylindrical
hole, single-side
Without 15 15.875 15 15.875 16 16.1 10 10.9 27 27.5 19 19.4 15.875
70° ~ 90° Single- *16 16 - - - - - - - - - - - - - - 16
H Counter sink sided
19 19.05 19 19.05 19 19.3 13 13 33 33 23 23.3 19.05
Partly cylindrical
C hole, double-side
Without
*20 20 - - - - - - - - - - - - - - 20
70° ~ 90° Double-
J Counter sink sided 22 22.225 22 22.6 38 38.5 27 27.1 22.225
*25 25 - - - - - - - - - - - - - - 25
X - - -
25 25.4 25 25.4 25 25.8 44 44 31 31 25.4
31 31.75 31 31.75 32 32.2 55 55 38 38.8 31.75
*32 32 - - - - - - - - - - - - - - 32
When M0 is included in Designation, the inscribed-circle diameter is metric size.
B006 www.tungaloyamerica.com *
ISO Designation

Insert
 Detailed accuracy for J,K,L,M,N and U classes Note on insert thickness Negative insert
With regard to the insert
For inserts with nose corner angles larger than 55˚ Unit: mm thickness for chipbreaker
Tolerance on inscribed circle dia.

s
(ød)
Tolerance on corner height (m) inserts, the thickness (s)
Inscribed Insert shapes applied
circle drawn in the outlined insert
J,K,L,M,N (class) U (class) J,K,L,M,N (class) U (class) Pojitive insert
shapes on pages XX to XX is
6.35 defined as “s” (height from

s
±0.05 ±0.08 ±0.08 ±0.13 H W the bottom face to the cutting
9.525 edge) shown in the figure at
O R right. Thickness
12.7 ±0.08 ±0.13 ±0.13 ±0.2 Symbol
(mm)
15.875 P
Inscribed circle (ød) X1 1.39
±0.1 ±0.18 ±0.15 ±0.27 S
19.05 Corner height (m) 01 1.59
25.4 ±0.13 ±0.25 ±0.18 ±0.38 T T1 1.98(1.79)
31.75 C,E,M 02 2.38
±0.15 ±0.25 ±0.2 ±0.38 T2 2.78
32
03 3.18

m
For M-type inserts with nose corner angles of 55˚ (Shape: D),

ød
35˚ (Shape: V), 25˚ (Shape: Y) Unit: mm T3 3.97
Inscribed Tolerance on inscribed circle dia. Tolerance on corner height (m) Insert shapes applied
circle (ød) 04 4.76
6.35 D 05 5.56
±0.05 ±0.11

m
9.525 06 6.35

ød
12.7 ±0.08 ±0.15 07 7.94
15.875 09 9.52
±0.1 ±0.18
19.05
Thickness
6.35 V
±0.05 ±0.16
9.525 Y 6 Thickness
[Example]
6 7 10

04 08 - TM
T3 04 F N - JS
6 7 8 9 10
(Supplementary symbol)
(Optional symbol) (Optional symbol)
7 Corner radius 8 Symbols of major cutting edge 9 Hand of insert 10 Chipbreakers
Condition of
Symbol Applications Symbol Applications
Symbol cutting Shape Symbol Hand
edge 01(TF) Precision finishing (Basic selection) CB Medium cutting
rε R Right TS Finishing (Basic selection) CM Medium cutting of cast irons
Sharp TSF Finishing (Basic selection) All-
Corner radius rε F round Medium cutting
Symbol (mm) edge L Left
TM Medium cutting (Basic selection) A Finishing (Right and left hand)
00 0.03 N Neutral THS Medium to heavy cutting
(Basic selection) B Finishing (Right and left hand)
Honed
02 0.2 E rounded TRS Medium to heavy cutting C Finishing (Right and left hand)
TUS Heavy cutting D Finishing (Right and left hand)
04 0.4 edge N
DM Medium cutting P Finishing of Aluminium alloys

08 0.8 Honed HRF Finishing W Finishing (Angular type)

W.T chamfered HRM Finishing to medium cutting PSF Finishing (Positive type)
12 1.2 edge Finishing to light cutting
HMM Medium cutting PSS (Positive insert)
16 1.6 R SF Finishing of stainless steels PS Finishing to medium cutting
(Positive type Basic selection)
Combination
20 2.0 S SS Finishing of stainless and mild steels PM Medium cutting (Positive type)
honed edge Finishing to medium cutting of
SM Medium cutting of stainless steels AL aluminium alloys
24 2.4 S Medium cutting of stainless steels RS Medium cutting (For round inserts)
Medium to heavy cutting of stainless W Finishing (Angular type)
28 2.8 SH steels
For heat-resisting alloys and stainless H Finishing (Parallel)
L SA steels
32 3.2
ZF Finishing and copying 11 Finishing
Finishing to medium cutting and Small depth of cut and high feed
ZM copying 61 (For round inserts)
NS Finishing and copying S1 Finishing (For KNMX type)
Finish to medium cutting and
NM copying J08,J10 For small lathes
AS Small depth of cut and high feed JS For small lathes
AM Small depth of cut and high feed JRP For small lathes
FW Finishing (Wiper type) JPP For small lathes
Finishing to medium cutting
SW (Wiper type) JSP For small lathes
Small depth of cut and high feed
AFW (Wiper type Inserts)
Small depth of cut and high feed
ASW (Wiper type Inserts)

Tungaloy B007
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Steel
Chipbreaker System for Turning (Negative Inserts)
0.433
T9105 T9105 T9115
0.394 T9115
GT9530 T9115 T9125
0.354 T9125
Depth of cut: ap (in)

NS9530 T9125
0.315
T9135
TH 12 T9135 THS 25
0.276 TSF
0.236
0.197 NS9530
0.157 T9105 T9115 T9115
T9115 T9125 T9125
0.118 T9125
0.079 TF TM T9135 THS 16 THS 19
0.039
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028 0.032 0.036 0.040 0.044
Feed: f (ipr)
CVD coated grades Coated cermets / Cermets
1640 1640
T9105
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

1300 1300

980 980
GT9530
T9115

650 650 NS9530

T9125

330 330
T9135

0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032

Feed: f (ipr) Feed: f (ipr)
Chipbreaker Appearance Features Chipbreaker Appearance Features
The sharp cutting edge and raised General purpose chipbreaker used for
projection near corner contribute to medium cutting.
excellent chip control at very small depths Unique chipbreaker geometry with sharp
TF of cut and low feeds. TM edges and large rake angle assures free
Economical M-class tolerance and low cutting action in a wide range of cutting
cost. conditions.
First choice chipbreaker for finishing steels. Double-sided 3-dimensional chipbreaker
The dimple structure decreases the contact with a wide land and broad groove used
area between the insert surface and chips, for medium to heavy cutting including
TSF resulting in significant reduction of heat
TH interruption and unfavorable surface
occurrence. conditions.
Also performs well in high feed machining.
Excellent chip control in a broad range of
depth of cut.
Strong cutting edge being suitable for
THS interrupted and high feed operations.

STA N DA R D C U T T I N G C O N D I T I O N S
Cutting speed: Vc (sfm)
Chip- Depth of cut Feed Low carbon Medium High carbon
ISO Operation Work condition Grade
breaker ap (in) f (ipr) steels, carbon steels, steels,
Alloy steels Alloy steels Alloy steels
Precision finishing Continuous to light
interrupted TF NS9530 0.002 - 0.020 0.001 - 0.006 500 - 820 330 - 820 330 - 660
Continuous to light TSF GT9530 0.008 - 0.060 0.003 - 0.016 500 - 980 260 - 820 260 - 660
interrupted
Finishing
Heavy interrupted TSF T9125 0.008 - 0.060 0.003 - 0.016 400 - 820 260 - 660 260 - 500
TM T9105 0.040 - 0.200 0.008 - 0.020 590 - 1150 590 - 1150 590 - 980

Medium Continuous to TM T9115 0.040 - 0.200 0.008 - 0.020 500 - 980 500 - 980 400 - 820
cutting heavy interrupted TM T9125 0.040 - 0.200 0.008 - 0.020 400 - 820 260 - 660 260 - 500
TM T9135 0.040 - 0.200 0.008 - 0.020 160 - 590 160 - 500 160 - 400
TH T9105 0.120 - 0.240 0.012 - 0.024 590 - 1150 590 - 1150 590 - 980
Medium TH T9115 0.120 - 0.240 0.012 - 0.024 500 - 980 500 - 980 400 - 820
Continuous to
to heavy
heavy interrupted TH T9125 0.120 - 0.240 0.012 - 0.024 400 - 820 260 - 660 260 - 500
cutting
TH T9135 0.120 - 0.240 0.012 - 0.024 160 - 590 160 - 500 160 - 400
Low carbon steels, Alloy steels: 1018, 1020, etc. Medium carbon steels, Alloy steels: 1045, 4140, etc. High carbon steels, Alloy steels: 8620, etc.

B008 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Steel

Continuous Light interrupted Heavy interrupted

Basic Basic
Fracture
TSF
GT9530
Precision finishing
[ ap = ~ 0.020 in ]

Wear 01
GT9530

TF TF
NS9530 NS9530

Basic Basic Basic

TSF TSF
[ ap = 0.012 ~ 0.060 in ]

Fracture Fracture
T9115 T9135
Finishing

TSF Chip ZF TSF TSF

GT9530 control GT9530 GT9530 T9125

Basic Basic Basic

TM DM
[ ap = 0.039 ~ 0.157 in ]

Fracture Fracture
T9135 T9135
Medium cutting

Wear
TM Wear TM
T9105 T9115

TM Chip ZM TM TM
T9115 control T9115 T9125 T9135
Medium to heavy cutting

Basic Basic Basic

TH TUS
[ ap = 0.118 ~ 0.236 in ]

Fracture Fracture
T9135 T9135

Wear
TH Wear
TH
T9105 T9115

TH Chip TM TH TH
T9115 control T9115 T9125 T9135

Tungaloy B009
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Stainless Steel
Chipbreaker System for Turning
0.276
T6120
0.236 T6120 T6130
Depth of cut: ap (in)

T6130 AH630
0.197 AH630 SM AH645 SH
SF T6130
0.157 AH630
AH645
0.118

0.079

0.039

0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Austenitic stainless steel Ferritic / martensite stainless steel Precipitation hardened stainless steel
980 980 980
T6120 T6130
T6130 T6120
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

820 820 AH630 820
AH630
650 650 650
T6120
500 500 500 T6130

330 330 330

160 160 160

AH645 AH645
AH630
0 0 0
Light cutting Heavy cutting Light cutting Heavy cutting Light cutting Heavy cutting
Light interrupted Heavy interrupted Light interrupted Heavy interrupted Light interrupted Heavy interrupted

Chipbreaker Appearance Features Chipbreaker Appearance Features

Exellent chip control when finish Applicable to a wide range of
cutting. cutting condition with sharp edge.
SF Outstanding chip control when high SM Recommended chipbreaker for
feed turning at small depth of cut. stainless steel turning.

Suitable for roughing operations

and interrupted machining with
SH tough cutting edges.

STA N DA RD CUT T ING CONDIT IO N S

ISO Operation Work condition Chipbreaker Grade Depth of cut Feed Cutting speed
ap (in) f (ipr) Vc (sfm)
Continuous SF T6120 0.020 - 0.098 0.003 - 0.018 460 - 790
Finishing Continuous to light interrupted SF T6130 0.020 - 0.098 0.003 - 0.018 330 - 660
Heavy interrupted SF AH630 0.020 - 0.098 0.003 - 0.018 300 - 620
Continuous SM T6120 0.040 - 0.160 0.008 - 0.020 460 - 790
Continuous to light interrupted SM T6130 0.040 - 0.160 0.008 - 0.020 330 - 660
Medium cutting
Light interrupted SM AH630 0.040 - 0.160 0.008 - 0.020 300 - 620
Heavy interrupted SM AH645 0.040 - 0.160 0.008 - 0.020 230 - 500
Continuous to light interrupted SH T6130 0.080 - 0.240 0.012 - 0.024 330 - 660
Medium to
Light interrupted SH AH630 0.080 - 0.240 0.012 - 0.024 300 - 620
heavy cutting
Heavy interrupted SH AH645 0.080 - 0.240 0.012 - 0.024 230 - 500
Stainless steels: 304SS, 316SS, etc.

B010 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Stainless Steel

Continuous Light interrupted Heavy interrupted

Basic Basic Basic

SF SF SF
[ ap = 0.020 ~ 0.060 in ]

Basic Fracture Basic Fracture Basic Fracture

T6130 AH630 AH645
Finishing

Wear SF Wear SF
T6120 T6130

SF SF SF
T6120 T6130 AH630

Basic Basic Basic

Fracture SM SH
[ ap = 0.039 ~ 0.157 in ]

Basic Basic Basic Fracture

AH645 AH645
Medium cutting

Wear SM Wear SM
T6120 T6130
SM Chip
SM SM
T6130 control SF AH630 AH645
T6130

Basic Basic Basic

Medium to heavy cutting

SH SH
[ ap = 0.079 ~ 0.236 in ]

Fracture Fracture
AH630 AH645

Wear SH Wear SH Wear SH

T6120 T6130 AH630

SH SH SH
Chip SM
T6130 control
T6130 AH630 AH645

Tungaloy B011
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Cast Iron
Chipbreaker System for Turning (Negative Inserts)
0.276
All-round T515
T5105 T5105 T515
0.236
T5115 T5115 T5105
Depth of cut: ap (in)

T5125
0.197 CF CH
T5115
T5125
0.157 BX930
BX950
0.118
T-CBN
0.079 T515
T5105
0.039 CM T5115
T5125
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)
Grey cast irons Ductile cast irons High speed cutting: for grey cast irons

2300 1970
T5105 T515
1970 4920
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

1640

1640
1300
T5105 BX930
1300 T5125 3300
980 T515, T5115
BX950, BXC90
980 FX105
650 T5125
650 1640
T515
330 330
T5115
0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032
Feed: f (ipr) Feed: f (ipr) Feed: f (ipr)
Chip- Chip-
breaker Appearance Features breaker Appearance Features
T-CBN inserts. First choice chipbreaker for cast iron.
No Performs well in high speed finishing An all around chipbreaker, which is applicable
chip- for a wide range of cutting conditions from
breaker of cast iron. CM continuous to interrupted machining with the
positive land and wide chip pocket
(T-CBN)
Chipbreaker with reinforced cutting-edge for
Low cutting force chipbreaker for cast iron. cast iron.
Combined with an arc-shaped concave and Utilizing the land support and negative land
CF a high rake (substantially 20° rake angle),
allows drastically reducing cutting forces
CH design, features stable insert seating and
high cutting edge strength even in heavy
and suppressing the deformation of thin cutting.
walled components and burr occurrence.
Highly reliable chipbreaker for medium cutting
under a wide range of conditions from continuous
All-round to interrupted cutting.

STA N DA R D C U T T I N G C O N D I T I O N S
Chip- Depth of cut Feed Cutting speed: Vc (sfm)
ISO Operation Work condition Grade ap (in) f (ipr)
breaker Grey cast irons Ductile cast irons
Continuous Without BX930 0.002 - 0.020 0.002 - 0.008 984 - 3937 328 - 1640
High speed
Light interrupted Without BX950 0.002 - 0.020 0.002 - 0.012 984 - 3281 328 - 984
cutting
Continuous Without BXC90 0.003 - 0.118 0.002 - 0.016 984 - 3281 328 - 984
Continuous CF T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
Finishing Light interrupted CF T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
Continuous CM T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
Continuous AR T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
Medium
Light interrupted CM T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
cutting
Continuous CH T515 0.118 - 0.236 0.008 - 0.024 150 - 2297 459 - 1214
Continuous CH T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
Heavy
Light interrupted CH T515 0.039 - 0.197 0.004 - 0.020 150 - 2297 459 - 1214
cutting
Continuous CH T515 0.118 - 0.236 0.008 - 0.024 150 - 2297 459 - 1214
Grey cast irons: Class 25, etc. Ductile cast irons: 65-45-12, etc.

B012 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Cast Iron

Continuous Light interrupted Heavy interrupted

Basic Basic Basic

All-round All-round CH
[ ap = 0.020 ~ 0.079 in ]

Wear Wear Wear

T5105 T5105 T5105
Finishing

Fracture CH Fracture CH
T515 T5125

All-round All-round CH
Burr CF Burr CF Burr All-round
T515 occurrence
T5105 T515 occurrence
T5115 T515 occurrence
T515

Basic Basic Basic

All-round All-round CH
[ ap = 0.039 ~ 0.197 in ]

Wear Wear Wear

T5105 T5105 T5105
Medium cutting

Fracture CH Fracture CH
T515 T5125

All-round All-round CH
Burr CF Burr CF Burr All-round
T515 occurrence
T5105 T515 occurrence
T5115 T515 occurrence
T515

Basic Basic Basic

All-round All-round CH
Medium to heavy cutting
[ ap = 0.118 ~ 0.236 in ]

Wear Wear Wear

T5105 T5105 T5105

Fracture CH Fracture CH
T515 T5125

All-round All-round CH
Burr CF Burr CF Burr All-round
T515 occurrence
T5105 T515 occurrence
T5115 T515 occurrence
T515

Tungaloy B013
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Non-ferrous Metal
Chipbreaker System for Turning (Negative Inserts)
0.276

0.236
Depth of cut: ap (in)

0.197 T-DIA
0.157

0.118
P
DX140 DX120
0.079 TH10

0.039

0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Aluminum alloys (Si < 12%) Aluminum alloys (Si * 12%) Copper alloys
9840 3300 6560
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

8200
2630

6560
DX140 1970
4920 DX140 3300
DX140
1300
3300 DX120 KS05F
TH10 650 TH10
1640

DX120
0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032
Feed: f (ipr) Feed: f (ipr) Feed: f (ipr)
Chip- Chip-
breaker Appearance Features breaker Appearance Features
No Performs well in high speed With The wide chipbreaker width
chip- finishing of non-ferrous materials. chip- contributes to excellent chip
breaker breaker control.
(T-DIA) (T-DIA)

Excels in sharpness of cutting

edges and effectively used for
P machining non-ferrous metals
such as aluminum alloys and
copper alloys.

STA N DA R D C U T T I N G C O N D I T I O N S
Cutting speed: Vc (sfm)
Work Chip- Depth of cut Feed Aluminum alloys Aluminum alloys Copper
ISO Operation Grade
condition breaker ap (in) f (ipr) (Si < 12%) (Si > 12%) alloys

Continuous With DX120 0.002 - 0.040 0.002 - 0.006 1640 - 8200 1310 - 2630 1640 - 4920
Precision
finishing Light
Without DX140 0.002 - 0.040 0.002 - 0.008 980 - 8200 - 1640 - 4920
interrupted

Continuous Without DX140 0.002 - 0.040 0.002 - 0.006 1640 - 8200 1310 - 2630 1640 - 4920

Finishing Light interrupted Without DX140 0.002 - 0.040 0.002 - 0.006 980 - 5900 1310 - 1970 1310 - 3940

Heavy
P TH10 0.020 - 0.160 0.008 - 0.020 330 - 1640 330 - 660 330 - 660
interrupted

Continuous P TH10 0.020 - 0.160 0.008 - 0.020 330 - 3280 330 - 980 330 - 980

Medium
Light interrupted P TH10 0.020 - 0.160 0.008 - 0.020 330 - 2630 330 - 660 330 - 660
cutting

Heavy interrupted P TH10 0.020 - 0.160 0.008 - 0.020 330 - 1640 330 - 660 330 - 660

B014 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Non-ferrous Metal

Continuous Light interrupted Heavy interrupted

Basic Basic With

Surface chipbreaker T-DIA
DX120
Precision finishing
[ ap = ~ 0.020 in ]

Wear T-DIA Wear

T-DIA
DX140 DX160
With
chipbreaker T-DIA
DX120 DX140

Basic With Basic Basic

Surface chipbreaker T-DIA Fracture P
[ ap = 0.020 ~ 0.079 in ]

DX120 TH10
Finishing

Wear
T-DIA Wear T-DIA
DX160 DX160

T-DIA T-DIA P
DX140 DX140 TH10

Basic Basic Basic

[ ap = 0.039 ~ 0.157 in ]
Medium cutting

Wear T-DIA Wear T-DIA

DX140 DX140

P P P
TH10 TH10 TH10

Tungaloy B015
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Superalloys and titanium

Chipbreaker System for Turning (Negative Inserts)
0.276
AH8015 AH8015
0.236 HRF AH8005 AH8005
Depth of cut: ap (in)

0.197

0.157 HRM
BX950
0.118 BX480

0.079

0.039
T-CBN
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Titanium alloys Ni-base alloys

1300 1300
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

980 980

650 650
BX950 BX950
BX480 M714B
330 AH8005 330
AH8005
AH8015 AH8015

0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032

Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

Suitable for finishing operation of T-CBN inserts.
superalloys. Special protrusion provides No Performs well in finishing of heat-resistant
excellent chip control in lower depth of chip- or titanium alloys.
HRF cut. breaker
(T-CBN)

The 1st recommended chipbreaker for

supperalloy turning. Optimized geometry
provides stable chip control in various
HRM depth of cut.

STA N DA R D C U T T I N G C O N D I T I O N S
Chip- Depth of cut Feed Cutting speed: Vc (sfm)
ISO Operation Work condition Grade
breaker ap (in) f (ipr) Titanium alloys Ni-base alloys
Without BX950 0.004 - 0.020 0.002 - 0.008 330 - 660 230 - 980
Continuous
Precision Without M714B 0.004 - 0.020 0.002 - 0.008 - 230 - 1310
finishing
Light interrupted Without BX480 0.004 - 0.020 0.002 - 0.008 330 - 660 -

Continuous HRF AH8005 0.020 - 0.060 0.002 - 0.010 66 - 330 66 - 330

Finishing Light interrupted HRF AH8015 0.020 - 0.060 0.002 - 0.010 66 - 260 66 - 160

Heavy interrupted HRF AH8015 0.020 - 0.060 0.002 - 0.010 33 - 200 33 - 130

Continuous HRM AH8005 0.020 - 0.160 0.004 - 0.016 66 - 330 66 - 330

Finishing to Light interrupted HRM AH8015 0.020 - 0.160 0.004 - 0.016 66 - 260 66 - 160
medium cutting
Heavy interrupted HRM AH8015 0.020 - 0.160 0.004 - 0.016 33 - 200 33 - 130

Ni-base alloys: INCONEL718, etc.

Titanium alloys: Ti-6Al-4V, etc

B016 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Superalloys and titanium

Continuous Light interrupted Heavy interrupted

Basic Basic
Fracture
No chipbreaker
TH10
Precision finishing
[ ap = ~ 0.020 in ]

T-CBN T-CBN
BX950 BX950

Basic Basic Basic

HRF HRM HRM
[ ap = 0.020 ~ 0.060 in ]

Wear Fracture Fracture

AH8005 AH8015 AH8015
Finishing

Wear HRF Wear HRF

AH8005 AH8005

HRF HRF HRF

AH8015 AH8015 AH8015

Basic Basic Basic

SM SM
[ ap = 0.020 ~ 0.157 in ]

Fracture Fracture
AH630 AH630
Medium cutting

Wear HRM Wear HRM Wear HRF

AH8005 AH8005 AH8005

HRM Chip HRF HRM HRM

AH8015 control AH8015 AH8015 AH8015

Tungaloy B017
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: NEG AT I V E I N S E R TS

Hard Materials
Chipbreaker System for Turning (Negative Inserts)
0.276

0.236
Depth of cut: ap (in)

0.197

0.157

0.118 BXM10 BX310

BXM20 BX330
0.079 BXA20 BX360
BX380
0.039 T-CBN
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Coated T-CBN T-CBN

Coated T-CBN T-CBN

980 980
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

BX310
BXM10 BXM20
650 650

BX360 BX380
330 330
BXA20
BX330

Continuous Light Medium Heavy Continuous Light Medium Heavy

interrupted interrupted interrupted interrupted interrupted interrupted

Chipbreaker Appearance Features Chipbreaker Appearance Features

No Performs well in finishing of When used in removing a
chip- hardened steel. carburized layer, excels in chip
breaker
(T-CBN)
HF control at small depth of cut.

When used in removing a

carburized layer, excels in chip
HM control at large depth of cut.

STA N DA RD CUT T ING CONDIT IO N S

Work Depth of cut Feed Cutting speed
ISO Operation Chipbreaker Grade
condition ap (in) f (ipr) Vc (sfm)
Continuous to BXM10
Precision finishing Without 0.002 - 0.008 0.001 - 0.007 500 - 1150
light interrupted BXA20
BXM10
Continuous to
Finishing Without BXM20 0.002 - 0.020 0.002 - 0.010 230 - 720
heavy interrupted
BXA20

Continuous HF BXM20 0.008 - 0.030 0.002 - 0.008 230 - 660

Removing of
carburized layer BXM20
Continuous HM 0.020 - 0.040 0.002 - 0.008 230 - 660
BXA20
Hardened steels, Pre-hardened steels: D2, H13, etc.

B018 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : NEG AT IV E I N S E R TS

Hard Materials

Continuous Light interrupted Heavy interrupted

Basic Basic
Fracture
-H
BXM20
Precision finishing
[ ap = ~ 0.008 in ]

T-CBN T-CBN For high T-CBN

BXM10 BXA20 speed
Wear BXM10

Basic Basic Basic

Fracture
-H Fracture
-H
BXM20 BXM20
[ ap = ~ 0.020 in ]
Finishing

T-CBN T-CBN For high T-CBN T-CBN

speed
BXM10 BXA20 Wear BXM10 BXM20

Tungaloy B019
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Steel
Chipbreaker System for Turning (Positive Inserts)
0.276 GT9530
NS9530
0.236 AH725
Depth of cut: ap (in)

T9115 GT9530
0.197 GT9530
NS9530 T9125 NS9530
PSF T9115
NS9530
0.157 T9115
T9125
PS PM T9125
0.118
01 GT9530
0.079 NS9530
AH725
0.039 T9115
PSS T9125
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)
CVD / PVD coated grades Coated cermets / Cermets
980 1640
T9115
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

1300

650
980
GT9530
T9125
650
330 NS9530

AH725 330

0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032

Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

The sharp cutting edge and raised 3-dimensional chipbreaker designed to
projection near corner contribute to have excellent chip control capability and
low cutting force in finishing to medium
01 excellent chip control at very small depth PS cutting. Low cost, M-class positive insert
of cut and low feed. used for high efficiency boring in a wide
range of applications.
Developed chipbreaker for finishing at low Developed chipbreaker for medium
cutting depths. Optimal chip control due cutting. Excellent chip control due to
PSF to pre-positioned chipbreaker element. PM wide, positive chip flow zone.

3-dimensional chipbreaker designed to

have excellent chip control capability and
low cutting force in finishing to medium
PSS cutting. Low cost, M-class positive insert
used for high efficiency boring in a wide
range of applications.

STA N DA R D C U T T I N G C O N D I T I O N S
Cutting speed: Vc (sfm)
Chip- Depth of cut Feed Low carbon Medium car- High carbon
ISO Operation Work condition Grade
breaker ap (in) f (ipr) steels, bon steels, steels,
Alloy steels Alloy steels Alloy steels
Precision Continuous 01 NS9530 0.002 - 0.020 0.001 - 0.006 500 - 820 260 - 720 260 - 590
finishing Light interrupted 01 NS9530 0.002 - 0.020 0.001 - 0.006 500 - 820 260 - 720 260 - 590
Continuous PSS NS9530 0.004 - 0.020 0.002 - 0.012 500 - 820 260 - 720 260 - 590
Finishing Light interrupted PSS NS9530 0.004 - 0.020 0.002 - 0.012 500 - 820 260 - 720 260 - 590
Heavy interrupted PSS NS9530 0.004 - 0.020 0.002 - 0.012 500 - 820 260 - 720 260 - 590
Continuous PS NS9530 0.012 - 0.079 0.003 - 0.012 500 - 820 260 - 720 260 - 590
Finishing to light
Light interrupted PS NS9530 0.012 - 0.079 0.003 - 0.012 500 - 820 260 - 720 260 - 590
cutting
Heavy interrupted PS NS9530 0.012 - 0.079 0.003 - 0.012 500 - 820 260 - 720 260 - 590
Finishing to Continuous to PS T9115 0.020 - 0.098 0.003 - 0.012 500 - 980 330 - 660 260 - 590
Medium cutting Heavy interrupted PS T9125 0.020 - 0.098 0.003 - 0.012 400 - 820 260 - 590 260 - 400
Continuous to PM T9115 0.040 - 0.120 0.006 - 0.012 500 - 980 330 - 660 260 - 590
Medium cutting
Heavy interrupted PM T9125 0.040 - 0.120 0.006 - 0.012 400 - 820 260 - 590 260 - 400
Low carbon steels, Alloy steels: 1018, 1020, etc. Medium carbon steels, Alloy steels: 1045, 4140, etc. Hi carbon steels, Alloy steels: 8620, etc.

B020 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Steel

Continuous Light interrupted Heavy interrupted

Basic Basic
Fracture
PSF
NS9530
Precision finishing
[ ap = ~ 0.020 in ]

01 01
NS9530 NS9530

Basic PSS Basic PSS Basic PSS

Wear Wear Wear
[ ap = 0.004 ~ 0.020 in ]

GT9530 GT9530 GT9530

Finishing

Fracture
PS Fracture
PS Fracture
PS
NS9530 NS9530 NS9530

PSS Chip PSF PSS Chip PSF PSS Chip PSF

NS9530 control NS9530 NS9530 control NS9530 NS9530 control NS9530
Finishing to Medium cutting

Basic Basic Basic

PS PS PM
[ ap = 0.020 ~ 0.098 in ]

Fracture Fracture Fracture

T9125 T9125 T9125

Wear
PS Wear
PS
NS9530 NS9530

PS PS PS
T9115 T9115 T9125

Basic PM Basic Basic

Wear
PM
[ ap = 0.039 ~ 0.118 in ]

Fracture
NS9530 T9125
Medium cutting

PM PM PM
T9115 T9115 T9125

Tungaloy B021
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Stainless Steel
Chipbreaker System for Turning (Positive Inserts)
0.276
T6120 T6120
0.236 GH330 T6130
AH725 T6130
Depth of cut: ap (in)

AH630 AH630
0.197 AH645 AH645
W PSF
0.157 PM
PS T6120
0.118 T6130
AH630
0.079 AH645
AH725
0.039
PSS
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)
CVD coated grades PVD coated grades
820 820
T6120 AH630
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

650 650 GH330

500 500

330 330

160 160
T6130
AH645
AH725
0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032
Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

Designed to control the direction of chip 3-dimensional chipbreaker designed to
flow and used for precision finish boring. have excellent chip control capability and
Provides excellent chip evacuation which low cutting force in finishing to medium
W is important to attain a highly accurate PSS cutting. Low cost, M-class positive insert
bore. used for high efficiency boring in a wide
range of applications.
Developed chipbreaker for finishing at low 3-dimensional chipbreaker designed to
cutting depths. Optimal chip control due have excellent chip control capability and
to pre-positioned chipbreaker element. low cutting force in finishing to medium
PSF PS cutting. Low cost, M-class positive insert
used for high efficiency boring in a wide
range of applications.
D e v e l o p e d c h i p b re a k e r f o r m e d i u m
cutting. Excellent chip control due to
PM wide, positive chip flow zone.

STA N DA R D C U T T I N G C O N D I T I O N S
ISO Operation Work condition Chipbreaker Grade Depth of cut Feed Cutting speed
ap (in) f (ipr) Vc (sfm)
Precision finishing Continuous W GH330 0.002 - 0.079 0.001 - 0.008 330 - 500
Continuous PSF AH725 0.004 - 0.020 0.002 - 0.012 160 - 500
Finishing Light interrupted PSF AH725 0.004 - 0.020 0.002 - 0.012 160 - 500
Heavy interrupted PSF AH725 0.004 - 0.020 0.002 - 0.012 160 - 400
Continuous PSS AH630 0.012 - 0.079 0.003 - 0.012 300 - 620
Finishing to
Light interrupted PSS AH630 0.012 - 0.079 0.003 - 0.012 300 - 620
light cutting
Heavy interrupted PSS AH630 0.012 - 0.079 0.003 - 0.012 300 - 620
Continuous PS T6130 0.020 - 0.098 0.003 - 0.012 330 - 660
Finishing to
Light interrupted PS AH630 0.020 - 0.098 0.003 - 0.012 300 - 620
medium cutting
Heavy interrupted PS AH630 0.020 - 0.098 0.003 - 0.012 300 - 620
Continuous PM T6130 0.040 - 0.120* 0.006 - 0.012 330 - 660
Medium cutting Light interrupted PM AH630 0.040 - 0.120* 0.006 - 0.012 300 - 620
Heavy interrupted PM AH630 0.040 - 0.120* 0.006 - 0.012 300 - 620
* For CCMT0602 and DCMT0702 type inserts, a p = 0.020 - 0.098
Stainless steels: 304SS, 316SS, etc.

B022 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Stainless Steel

Continuous Light interrupted Heavy interrupted

Basic Basic
Precision finishing
[ ap = ~ 0.020 in ]

W W
GH330 GH330

Basic Basic Basic

PSS PSS PSS
[ ap = 0.012 ~ 0.060 in ]

Wear Fracture Fracture

T6130 AH630 AH630
Finishing

PSS
Wear
T6130

PSF PSF PSF

AH725 AH725 AH725
Finishing to Medium cutting

Basic Basic Basic

PS PM PM
[ ap = 0.020 ~ 0.098 in ]

Wear Fracture Fracture

T6130 AH645 AH645

PS PS
Wear Wear
T6130 T6130

PSS PS PS
AH630 AH630 AH630

Basic Basic Basic

PM PM
[ ap = 0.039 ~ 0.118 in ]

Fracture Fracture
AH645 AH645
Medium cutting

Wear
PM
T6130

PM PM PM
AH6130 AH630 AH630

Tungaloy B023
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Cast Iron
Chipbreaker System for Turning (Positive Inserts)
0.157
BX930 T515
BX950 T5115
Depth of cut: ap (in)

0.118
T-CBN CM
0.079
T5115

0.039
No chipbreaker

0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)
Grey cast irons Ductile cast irons
1970

BX930
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

3300 1640
BX930
1300

BX950
980
1640
650
T515, T5115 T5115, T515
330

0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032

Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

Performs well in high speed All-around chipbreaker for
No finishing of cast iron. general purpose cutting,
chip-
breaker CM provides low cutting forces
(T-CBN) and excellent performance in
finishing to medium cutting.
Can cover a wide range of
No applications from finishing to
chip- roughing of cast irons.
breaker Excels in cutting edge strength.

STA N DA RD CUT T ING CONDIT IO N S

Chip- Depth of cut Feed Cutting speed: Vc (sfm)
ISO Operation Work condition Grade
breaker ap (in) f (ipr) Grey cast irons Ductile cast irons
Continuous Without BX930 0.002 - 0.020 0.002 - 0.008 980 - 3940 330 - 1640

Precision
Without BX950 0.002 - 0.020 0.002 - 0.008 980 - 2630 330 - 980
finishing
Light interrupted
Without BX470 0.002 - 0.020 0.002 - 0.008 980 - 2630 330 - 980

Continuous CM T515 0.002 - 0.079 0.002 - 0.012 500 - 2300 500 - 980
Finishing
Heavy interrupted CM T515 0.002 - 0.079 0.002 - 0.012 330 - 660 330 - 660

Medium
Light interrupted CM T515 0.002 - 0.079 0.002 - 0.012 330 - 980 330 - 820
cutting
Grey cast irons: Class 25, etc.
Ductile cast irons: 65-45-12, etc.

B024 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Cast Iron

Continuous Light interrupted Heavy interrupted

Finishing to Medium cutting

Basic Basic Basic

[ ap = 0.020 ~ 0.118 in ]

Wear T-CBN
BX930

CM CM CM
T515 T515 T515

Tungaloy B025
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Non-ferrous Metal
Chipbreaker System for Turning (Positive Inserts)
0.276

0.236 DX140 DX120

Depth of cut: ap (in)

0.197
T-DIA
0.157

0.118 KS05F
0.079
AL
0.039

0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)
Aluminum alloys (Si < 12%) Aluminum alloys (Si * 12%) Copper alloys
9840 3300 6560
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

8200 2630

6560
DX140 1970
4920 DX140 3300
DX140
1300
3300 DX120 KS05F
KS05F 650 KS05F
1640

DX120
0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032
Feed: f (ipr) Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

Performs well in high speed The wide chipbreaker width
No finishing of non-ferrous materials. With contributes to excellent chip
chip- chip- control.
breaker breaker
(T-DIA) (T-DIA)

Extremely sharp cutting edge.

Polished surface. Excellent chip
AL forming at high cutting feeds. Low
power consumption.

STA N DA RD CUT T ING CONDIT IO N S

Cutting speed: Vc (sfm)
Work Chip- Depth of cut Feed Aluminum alloys Aluminum alloys Copper
ISO Operation Grade
condition breaker ap (in) f (ipr) (Si < 12%) (Si > 12%) alloys
Continuous With DX120 0.002 - 0.040 0.002 - 0.006 1640 - 8200 1310 - 2630 1640 - 4920
Precision
finishing
Light interrupted Without DX140 0.002 - 0.040 0.002 - 0.008 980 - 8200 - 1640 - 4920

Continuous Without DX140 0.002 - 0.040 0.002 - 0.006 1640 - 8200 1310 - 2630 1640 - 4920

Finishing Light interrupted Without DX140 0.002 - 0.040 0.002 - 0.006 980 - 5900 1310 - 1970 1310 - 3940

Heavy interrupted AL KS05F 0.020 - 0.197 0.004 - 0.020 330 - 1970 330 - 660 -

Continuous AL KS05F 0.020 - 0.197 0.004 - 0.020 330 - 3940 330 - 980 330 - 980
Medium
Light interrupted AL KS05F 0.020 - 0.197 0.004 - 0.020 330 - 2950 330 - 660 330 - 660
cutting
Heavy interrupted AL KS05F 0.020 - 0.197 0.004 - 0.020 330 - 1970 330 - 660 -

B026 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Non-ferrous Metal

Continuous Light interrupted Heavy interrupted

Basic Basic
Precision finishing
[ ap = ~ 0.020 in ]

Wear T-DIA Wear T-DIA

DX140 DX140
With With
chipbreaker chipbreaker
DX120 DX120

Basic Basic Basic

AL
[ ap = 0.020 ~ 0.079 in ]

Fracture
KS05F
Finishing

Wear T-DIA Wear T-DIA

DX160 DX160

T-DIA Chip
Withchipbreaker
With chipbreaker
T-DIA
T-DIA AL
T-DIA
DX140 control DX120 DX140 KS05F

Basic Basic Basic

[ ap = 0.039 ~ 0.197 in ]
Medium cutting

With chipbreaker
Wear T-DIA Wear
T-DIA
DX120 DX140

AL AL AL
KS05F KS05F KS05F

Tungaloy B027
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Superalloys and titanium

Chipbreaker System for Turning (Positive Inserts)
0.157
PS
AH8005
Depth of cut: ap (in)

0.118 AH8015

0.079
PSS
AH8005
AH8015
0.039
PSF
AH8005
AH8015
0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Titanium alloys Ni-base alloys

1300 1300
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

980 980

650 650
AH8005
AH8015 AH8005
AH8015
330 330

0 0.008 0.016 0.024 0.032 0 0.008 0.016 0.024 0.032

Feed: f (ipr) Feed: f (ipr)

Chipbreaker Appearance Features Chipbreaker Appearance Features

3-dimensional chipbreaker designed to Developed chipbreaker for finishing at low
have excellent chip control capability and cutting depths. Optimal chip control due
low cutting force in finishing to medium
PS cutting. Low cost, M-class positive insert PSF to pre-positioned chipbreaker element.
used for high efficiency boring in a wide
range of applications.
3-dimensional chipbreaker designed to
have excellent chip control capability and
low cutting force in finishing to medium
PSS cutting. Low cost, M-class positive insert
used for high efficiency boring in a wide
range of applications.

STA N DA RD CUT T ING CONDIT IO N S

Chip- Depth of cut Feed Cutting speed: Vc (sfm)
ISO Operation Work condition Grade
breaker ap (in) f (ipr) Titanium alloys Ni-base alloys
Continuous PSS AH8015 0.012 - 0.079 0.001 - 0.012 66 - 500 66 - 330
Finishing
Light interrupted PSS AH8015 0.012 - 0.079 0.001 - 0.012 66 - 500 66 - 330

Continuous PS AH8015 0.020 - 0.098 0.001 - 0.012 66 - 500 66 - 330

Finishing to
medium cutting
Light interrupted PS AH8015 0.020 - 0.098 0.001 - 0.012 66 - 500 66 - 330

Ni-base alloys: INCONEL718 etc.

Titanium alloys: Ti - 6Al - 4V etc.

B028 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Superalloys and titanium

Continuous Light interrupted Heavy interrupted

Basic Basic
[ ap = 0.012 ~ 0.079 in ]
Finishing

Wear PSS Wear PSS

AH8005 AH8005

PSS PSS PS
Fracture
AH8015 AH8015 AH8015
Finishing to medium cutting

Basic Basic All-round Basic All-round

PSS
[ ap = 0.020 ~ 0.098 in ]

Wear Fracture Fracture

AH8005 AH8015 AH8015

PS PS PS
AH8015 AH8015 AH8015

Tungaloy B029
Insert Tur n L i n e - C h i p breaker Guide
B A S I C C HIP BREA K ERS: P OSIT I V E I N S E R TS

Hard Materials
Chipbreaker System for Turning (Positive Inserts)
0.157
Depth of cut: ap (in)

0.118 BXA20 BX310

BXM10 BX330
BXM20 BX360
0.079
T-CBN
0.039

0
0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Coated T-CBN T-CBN

Coated T-CBN
980 980
Cutting speed: Vc (sfm)

Cutting speed: Vc (sfm)

T-CBN

BX310
650 BXM10 650

BXM20
BX360
330 330
BXA20 BX330

Continuous Light Medium Heavy Continuous Light Medium Heavy

interrupted interrupted interrupted interrupted interrupted interrupted

Chipbreaker Appearance Features

No Performs well in finishing of

chip- hardened steel.
breaker
(T-CBN)

STA N DA RD CUT T ING CONDIT IO N S

Work Depth of cut Feed Cutting speed
ISO Operation Chipbreaker Grade
condition ap (in) f (ipr) Vc (sfm)
No chipbreaker
Continuous BXM10 0.002 - 0.012 0.001 - 0.006 500 - 1150
(T-CBN)
Precision finishing
No chipbreaker BXM20
Light interrupted 0.002 - 0.012 0.001 - 0.006 230 - 720
(T-CBN) BXA20

Continuous No chipbreaker BXM20

Finishing 0.003 - 0.020 0.002 - 0.012 230 - 720
~ interrupted (T-CBN) BXA20

Hardened steels, Pre-hardened steels: D2, H13, etc.

B030 www.tungaloyamerica.com
Tur n L i ne - S e l e c t ion System

Insert
S E LE CTI ON SYST EM : P OSIT IV E IN S E R TS

Hard Materials

Continuous Light interrupted Heavy interrupted

Basic Basic
Fracture
T-CBN
BXA20
Precision finishing
[ ap = ~ 0.012 in ]

T-CBN T-CBN For high

speed
T-CBN
BXM10 BXM20 Wear BXM10

Basic Basic Basic

T-CBN Fracture
T-CBN
Fracture
BXA20 BXA20
[ ap = ~ 0.020 in ]
Finishing

T-CBN T-CBN For high

speed
T-CBN T-CBN
BXM10 BXM20 Wear BXM10 BXM20

Tungaloy B031
Insert Tur n L i n e - C h i p breaker Overview
Application C D S T V W Y
Negative type
with hole
80° 55° 90° 60° 35° 80° 25°
0.200

TF 0.160
ap (in)

0.120

0.080

0.040
12º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B063 B073 B082 B093 B097
0.200

01 0.160
ap (in)

0.120

0.080
Precision finishing

0.040
12º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B063 B073 B082 B093 B097
0.200

A~D 0.160
ap (in)

0.120
0.006
0.15 0.080
14º

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B073 B082, B083
0.200

W 0.160
ap (in)

0.120

0.080

0.040
14º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B083
0.200

TSF 0.160
Finishing

ap (in)

0.120

0.080

0.040
13º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B063 B073 B083 B093 B097
0.200

FW 0.160
ap (in)

0.120

0.080
Finishing (Wiper)

0.040
12º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B063 B083 B097
0.200

AFW 0.160
ap (in)

0.120

0.080

0.040
12º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B052 B097
0.200

ZF 0.160
Finishing

ap (in)

0.120

0.080
0.008
0.2
0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B053 B063 B083 B093 B097 B104

The page number for the product details is shown in red.

B032 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D S T V W Y
Application

Negative type
with hole
80° 55° 90° 60° 35° 80° 25°
0.200

11
0.160
Finishing

ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B053 B064 B074 B084 B093 B098
Finishing of mild steels

0.200

17 0.160
ap (in)

0.120

0.080

0.040
18º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B053 B064 B074 B084 B098
0.200

SF 0.160
ap (in)

0.120

0.080

0.040
18º

0
0.004 0.008 0.012 0.016 0.020 B053 B064 B074 B084 B093 B098
f (ipr)
0.200

CF 0.160
ap (in)

0.120

0.080
0.002
0.06
0.040
20º
Finishing

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B053 B064 B074 B084 B094 B098
0.200

HRF 0.160
ap (in)

0.120

0.080

0.040
20º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B053 B064 B074 B084 B094 B098
0.200

TS 0.160
ap (in)

0.120

0.080

0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B054 B065 B075 B085 B094 B098
0.394

SW 0.315
Finishing to medium cutting (Wiper)

ap (in)

0.236

0.157
0.008
0.2
0.078
10º

0
0.008 0.016 0.024 0.032 0.040
f (ipr)
B054 B065 B085 B099
0.394

ASW 0.315
ap (in)

0.236

0.157
0.008
0.2
0.078
18º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B054 B099

The page number for the product details is shown in red.

Tungaloy B033
Insert Tur n L i n e - C h i p breaker Overview
Application C D S T V W Y
Negative type
with hole
80° 55° 90° 60° 35° 80° 25°
High feed, small depth

0.394

AS 0.315
ap (in)

0.236
of cut

0.157
0.008
0.2
0.078
18º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B054 B065 B075 B085 B099
0.200

CB 0.160
(Double sided)

ap (in)

0.120
Boring

0.080

0.040
31º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B054 B065 B085 B099
0.200

NS 0.160
ap (in)

0.120

0.080

0.040
16º

0
Finishing

0.004 0.008 0.012 0.016 0.020

f (ipr) B055 B065 B075 B085 B099
0.200

0.160

SS
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B055 B066 B075 B086 B094 B099
0.394
Medium cutting

TM 0.315
ap (in)

0.236

0.157
0.008
0.2 0.078
6º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B055 B066 B075 B086 B094 B100
0.394

0.315

AM
ap (in)

0.236

0.157

0.010
0.25 0.078
8º

0
Finishing to medium cutting

0.008 0.016 0.024 0.032 0.040

f (ipr) B055 B066 B086 B100
0.200

NM 0.160
ap (in)

0.120

0.080

0.040
12º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B055 B066 B086 B100
0.200

TQ 0.160
ap (in)

0.120

0.080

0.040
17º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B056 B067 B086 B095 B100

The page number for the product details is shown in red.

B034 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D S T V W Y
Application

Negative type
with hole
80° 55° 90° 60° 35° 80° 25°
0.200
Finishing to medium

ZM 0.160
ap (in)

0.120
cutting

0.080

0.040
7º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B056 B067 B076 B087 B095 B100 B104
0.394

DM 0.315
ap (in)

0.236

0.25
0.010 0.157
Medium cutting

0.078
15º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B056 B067 B076 B087 B095 B101
0.394

0.315

All-round
ap (in)

0.236

0.157
0.008
0.2
0.078
15º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B056 B067 B076 B087 B095 B101
0.200
Finishing to medium

27 0.160
ap (in)

0.120
cutting

0.080

0.040
6º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B057 B067 B076 B087 B101
0.200

28 0.160
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B057 B068 B088 B095
0.200

32 0.160
ap (in)

0.120

0.012 0.080
Medium cutting

0.040

0
0.004 0.008 0.012 0.016 0.020
B088
f (ipr)
0.200

0.160

33
ap (in)

0.120

0.080

0.2
0.008 0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B057 B068 B088 B095 B101
0.200

37 0.160
ap (in)

0.120

0.080
0.008
0.2 0.040

0
30º

0.004 0.008 0.012 0.016 0.020

f (ipr) B057 B068 B077 B088 B101

The page number for the product details is shown in red.

Tungaloy B035
Insert Tur n L i n e - C h i p breaker Overview
Application C D R S T V W
Negative type
with hole
80° 55° 90° 60° 35° 80°
0.200
Medium cutting

0.160

38
ap (in)

0.120

0.080
0.008
0.2 0.040
10 º

0
0.004 0.008 0.012 0.016 0.020
B057 B068 B088
f (ipr)
0.394

61
0.315
Heavy cutting
(Single sided)

ap (in)

0.236
25,31
0.157
0.15
0.006 15,19
0.078 09,12
15º

0
0.016 0.032 0.048 0.064 0.080
B072
f (ipr)
0.200

Parallel 0.160
ap (in)

0.120

0.15
0.006 0.080

0.040
14º

0
0.004 0.008 0.012 0.016 0.020 B068
f (ipr)
0.394

SM 0.315
ap (in)

0.236

0.157
0.010
0.25
0.078
Medium cutting

10º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B058 B068 B077 B088 B096 B102
0.394

CM 0.315
ap (in)

0.236

0.157
0.010
0.25
0.078
15º

0
0.008 0.016 0.024 0.032 0.040
B058 B069 B077 B088 B096 B102
f (ipr)
0.394

P 0.315
ap (in)

0.236

0.157
30º

0.078

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B058 B069 B077 B089 B093
0.200
Finishing to medium

0.160

HRM
ap (in)

0.120
cutting

0.080
0.010
0.25 0.040
15º

0
0.004 0.008 0.012 0.016 0.020 B058 B069 B077 B089 B096 B102
f (ipr)
0.200
Medium cutting

0.160

HMM
ap (in)

0.120

0.080
0.010
0.25 0.040
15º

0
0.004 0.008 0.012 0.016 0.020 B058 B069 B078 B089 B096 B102
f (ipr)

The page number for the product details is shown in red.

B036 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D R S T V W
Application

Negative type
with hole
80° 55° 90° 60° 35° 80°
0.200

SA 0.160
ap (in)

0.120

0.080
Medium cutting

0.040
18º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B059 B069 B078 B089 B102
0.200

S
0.160
ap (in)

0.120

0.080
0.15
0.006
0.040
15º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B059 B069 B078 B090
0.394

0.315

TH
ap (in)

0.236
Medium to heavy cutting

0.157
0.3
0.012
0.078
20º

0
0.008 0.016 0.024 0.032 0.040 B059 B070 B078 B090 B103
f (ipr)
0.600

THS 0.480
25
ap (in)

0.360
19
0.4
0.016 0.240
12,16
0.120
20º

0
0.012 0.024 0.036 0.048 0.060 B059 B070 B078 B090 B103
f (ipr)
cutting (Single sided)

0.394
Medium to heavy

TRS 0.315
ap (in)

0.236

0.012
0.3 0.157 19,25
24º

0.078 12,16
0
0.008 0.016 0.024 0.032 0.040 B060 B079
f (ipr)
1.200

TU 0.960
ap (in)

0.720
Heavy cutting (Single sided)

0.014
0.35 0.480 = 25

0.240
=19
0
20º

0.016 0.032 0.048 0.064 0.080

f (ipr)
B060 B079
0.600

TUS 0.480
ap (in)

0.360
0.018
0.45 25
0.240

0.120
19
0
20º

0.012 0.024 0.036 0.048 0.060

f (ipr)
B060 B079

0.394
Medium to heavy

SH 0.315
ap (in)

0.236
cutting

0.157
0.4
0.016
0.078
20º

0
0.008 0.016 0.024 0.032 0.040
B060 B070 B079 B103
f (ipr)

The page number for the product details is shown in red.

Tungaloy B037
Insert Tur n L i n e - C h i p breaker Overview
Application C D R S T V W
Negative type
with hole
80° 55° 90° 60° 35° 80°
0.394
Medium to heavy

0.315

CH
ap (in)

0.236
cutting

0.157
0.4
0.016
0.078
15º

0
0.008 0.016 0.024 0.032 0.040
f (ipr) B060 B070 B079 B090 B103
0.200

- 0.160
ap (in)

0.120
Finishing to medium cutting

M,G-class 0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B061 B070 B072 B080 B091 B096 B103
0.200

8
Wiper 0.160
ap (in)

0.120
M-class 4
0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B061

C D KNMX LNGN R S T
Application

Negative type
without hole
80° 55° 55° 90° 90° 60°
0.200

S1 0.160
Finishing

ap (in)

0.120

0.080
0.35
0.014
0.040
13º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B105

The page number for the product details is shown in red.

B038 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D H R S T V
Application

Negative type
without hole
80° 55° 120° 90° 60° 35°
0.394

- 0.315
Finishing to medium cutting

ap (in)

0.236

G-class 0.157

0.078

0
0.008 0.016 0.024 0.032 0.040 B062 B071 B105 B081 B096
f (ipr)
0.200

- 0.160
ap (in)

0.120

M,G-class 0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B062 B071 B072 B081 B092
Finishing to roughing

0.200

- 0.160
ap (in)

0.120
M,G-class 0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
B071 B081
f (ipr)

The page number for the product details is shown in red.

Tungaloy B039
Insert Tur n L i n e - C h i p breaker Overview
Application C D R S T V Y
Positive 7°
with hole
80° 55° 90° 60° 35° 25°
0.200
Precision finishing

01 0.160
ap (in)

0.120

0.080
10º

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B106 B116 B133
0.200

PSF 0.160
ap (in)

0.120

0.080
0.12
0.005
0.040
20º
Finishing

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B106 B116 B133 B149
0.200

PF 0.160
ap (in)

0.120

0.008
0.2 0.080
10º

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B106 B116 B149
0.200

PSS 0.160
light cutting
Finishing to

ap (in)

0.120

0.080
0.006
0.15
0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B107 B117 B133 B149
0.200

PS 0.160
ap (in)

0.120

0.080
10º

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B107 B117 B129 B134 B149
0.200

ZF 0.160
Finishing to medium cutting

ap (in)

0.120

0.080 R0.008
R0.031
0.008
0.2 0.040
R0.016
8º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B155
0.200

ZM 0.160
ap (in)

0.120
R0.016
0.080 R0.031
0.040
7º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B155
0.200

23 0.160
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B107 B117 B129 B134

The page number for the product details is shown in red.

B040 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D R S T V Y
Application

Positive 7°
with hole
80° 55° 90° 60° 35° 25°
0.100
Finishing to medium

SW 0.080
cutting Wiper

ap (in)

0.060

0.040
0.008
0.2
0.020
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B107
0.200

24
Medium cutting

0.160
ap (in)

0.120
0.2
0.008 0.080
6º

0.040

0
0.004 0.008 0.012 0.016 0.020 B107 B117 B129 B134 B150
f (ipr)
0.200

W** 0.160
Finishing

ap (in)

0.120

0.1
0.004 0.080

0.040
14º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B108, B109 B118 B134
0.200
Finishing to medium

0.160

RS
ap (in)

0.120
cutting

0.080

0.2
0.008
5º

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B126
0.394

61 0.315
Heavy cutting

ap (in)

0.236

0.157
0.15
0.006 16,20,25
0.078
10,12
20º

0
0.016 0.032 0.048 0.064 0.080
f (ipr) B127
0.200

PM
Medium cutting

0.160
ap (in)

0.120

0.15
0.006 0.080

0.040
8º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B109 B118 B129 B135
0.200

CM 0.160
Finishing to medium cutting

ap (in)

0.120

0.080
0.010
0.25 0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B109 B118 B126 B129 B135 B150
0.200

SS 0.160
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B135

The page number for the product details is shown in red.

Tungaloy B041
Insert Tur n L i n e - C h i p breaker Overview
Application C D R S T V Y
Positive 7°
with hole
80° 55° 90° 60° 35° 25°
0.394

AL 0.315
ap (in)

0.236

0.008
0.2 0.157

0.078

0
º
20

0.008 0.016 0.024 0.032 0.040

f (ipr) B110 B119 B126 B135 B150
0.200

0.160
Finishing to medium cutting

All-round
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B110 B119 B150
0.200

0.160

Angular
ap (in)

0.120

0.080

0.040
23º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B110 B119
0.200

- 0.160
ap (in)

0.120
M,G-class 0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B110 B119
0.200

- 0.160
Finishing

ap (in)

0.120

(with hand) 0.080

0.040
23º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B136
small lathes (Sharp edge) small lathes (Sharp edge) small lathes (Sharp edge)

0.200
For external turning on

JS 0.160
9
ap (in)

0.120
9
0.080
9
0.040
10º

9
0
0.002 0.004 0.006 0.008 0.010
f (ipr)
B111 B120 B136
0.040
For internal turning on

JS 0.032
R0.004
ap (in)

0.024 R0.008
0.016
R0.016
0.008
10º

0
0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B111
0.040
For external turning on

9 9
0.032

JPP 9
ap (in)

0.024
9
0.016

0.008
10º

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B120

The page number for the product details is shown in red.

B042 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C D R S T V Y
Application

Positive 7°
with hole
80° 55° 90° 60° 35° 25°
0.040
9 9
0.032

JRP 9
ap (in)

0.024
9
0.016
For external turning on small lathes (Sharp edge)

0.008
10º

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B121

0.040
9 9
0.032

JSP 9
ap (in)

0.024
9
0.016

0.008
10º

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B121

0.394

J**
0.315
ap (in)

0.236

0.157

0.078
30º

0
0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B112 B121 B136, B137

0.160
Low cutting force

6RS 0.120
ap (in)

0.080
5º

0.25
0.010 0.040

0
0.008 0.016 0.024 0.032 0.040 0.048
f (ipr) B270

0.160

6RM
General use

0.120
ap (in)

0.080

0.17
0.007 0.040

0
15º

0.008 0.016 0.024 0.032 0.040 0.048

f (ipr) B270

The page number for the product details is shown in red.

Tungaloy B043
Insert Tur n L i n e - C h i p breaker Overview
Application C E S T V
Positive 11°
with hole
80° 75° 90° 60° 35°
0.200
Precision finishing

01 0.160
ap (in)

0.120

0.080

0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B138
0.200

PSF 0.160
ap (in)

0.120

0.080
0.005
0.12
0.040
20º
Finishing

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B113 B138
0.200

PF 0.160
ap (in)

0.120

0.080
0.008
0.2
10º

0.040

0
0.004 0.008 0.012 0.016 0.020
B113 B138
f (ipr)
0.200
Finishing to light

0.160

PSS
ap (in)

0.120
cutting

0.080

0.006
0.15 0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B113 B139
0.200

PS
0.160
ap (in)

0.120
Finishing to medium cutting

0.080

0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B113 B130 B139
0.200

0.160

23
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B130 B139
0.200
Medium cutting

0.160

24
ap (in)

0.120

0.080
0.2
0.008
0.040
6º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B114 B130 B140
0.200

W** 0.160
Finishing

ap (in)

0.120

0.1
0.004 0.080

0.040
14º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B114 B124 B130 B140, B141

The page number for the product details is shown in red.

B044 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
C E S T V
Application

Positive 11°
with hole
80° 75° 90° 60° 35°
0.200
Medium cutting

PM 0.160
ap (in)

0.120

0.080
0.15
0.006
0.040
8º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B115 B142
0.200

0.160

CM
ap (in)

0.120

0.080

0.010
0.25 0.040
10º

0
Finishing to medium cutting

0.004 0.008 0.012 0.016 0.020

f (ipr) B115 B131 B142
0.200

SS 0.160
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
B142
f (ipr)
0.200

H** 0.160
ap (in)

0.120

0.080

0.040
4.5º

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B143
0.200
Medium cutting

0.160
All-round
ap (in)

0.120

0.080
0.010
0.25
0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B115
0.200

- 0.160
ap (in)

0.120

M,G-class 0.080

0.040
Finishing to medium cutting

0
0.004 0.008 0.012 0.016 0.020
f (ipr)
B115 B131 B143, B144
0.200

- 0.160
ap (in)

0.120

(with hand) 0.080

0.040 Former Tungaloy-

standard hole
23º

0 Not ISO
0.004 0.008 0.012 0.016 0.020
f (ipr) B131
0.200

0.160

-
ap (in)

0.120
(with hand) 0.080

0.004
0.1 0.040 Former Tungaloy-
standard hole
Not ISO
14º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B143

The page number for the product details is shown in red.

Tungaloy B045
Insert Tur n L i n e - C h i p breaker Overview
Application C E S T V
Positive 11°
with hole
80° 75° 90° 60° 35°
For internal turning on

0.040

0.032

JS R0.004
small lathes

ap (in)

0.024 R0.008
0.016
R0.016
0.008
10º

0
0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B125 B144
0.040
9 9
0.032

JPP 9
ap (in)

0.024
9
0.016

0.008
10º
For external turning on small lathes

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B151
0.040
9 9
0.032
(Sharp edge)

JRP 9
ap (in)

0.024
9
0.016

0.008
10º

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B151
0.040
9 9
0.032

JSP 9
ap (in)

0.024
9
0.016

0.008
10º

0
0.0012 0.0024 0.0036 0.0048 0.0060
f (ipr) B151
0.100

0.080

J08
Finishing

ap (in)

0.060

0.040

0.020

0
15º

0.002 0.004 0.006 0.008 0.010

f (ipr) B125

W
Application

Positive 11°
with hole
80°
0.394

0.315

ML
Heavy cutting

ap (in)

0.236

0.157

0.078

0
0.020 0.040 0.060 0.080 0.100
10º

f (ipr) B152

The page number for the product details is shown in red.

B046 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
V W V W
Application

Application
Positive 5° Positive 5°
with hole with hole
35° 80° 35° 80°
0.200 0.200

0.160 0.160

Medium cutting
PSF 24
ap (in)

ap (in)
0.120 0.120

0.080 0.080
0.2
0.008
0.005
0.12 0.040 0.040

6º
20º

0 0
0.004 0.008 0.012 0.016 0.020 0.004 0.008 0.012 0.016 0.020
Finishing

f (ipr) f (ipr)
B147 B147
0.200 0.200

Finishing to medium
0.160 0.160

PF CM
ap (in)

ap (in)
0.120 0.120

cutting
0.080 0.080

0.008
0.2 0.040 0.040
10º

0 0.010
0.25 0
0.004 0.008 0.012 0.016 0.020 0.004 0.008 0.012 0.016 0.020

10º
f (ipr) f (ipr)
B147 B147
0.200 0.200

small lathes (Sharp edge)

Finishing to light cutting

0.160 For external turning on 0.160

PSS JS 9
ap (in)

ap (in)
0.120 0.120
9
0.080 0.080
9
0.006 0.040 0.040
0.15 9

10º
0 0
10º

0.004 0.008 0.012 0.016 0.020 0.002 0.004 0.006 0.008 0.010
f (ipr) f (ipr)
B147 B148
0.200 0.040
For internal turning on
Finishing to medium

0.160 0.032

PS JS R0.004
small lathes
ap (in)

ap (in)

0.120 0.024 R0.008

cutting

0.080 0.016
R0.016
0.040 0.008
10º

0 0
10º

0.004 0.008 0.012 0.016 0.020 0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B147 f (ipr)
B153
0.100 0.394
small lathes (Honed edge) small lathes (Sharp edge)
For external turning on

0.080 0.315

W08
ap (in)

ap (in)

0.060 0.236

0.040

0.020
J10 0.157

0.078
15º

0 0
30º

0.002 0.004 0.006 0.008 0.010 0.0016 0.0032 0.0048 0.0064 0.0080
Finishing

f (ipr) f (ipr)
B153 B148
0.200 0.394
For external turning on

0.160 0.315

W11
ap (in)

ap (in)

0.120 0.236

0.080

0.040
J10 0.157

0.078
15º

0 0
30º

0.004 0.008 0.012 0.016 0.020 0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) f (ipr)
B153 B148

The page number for the product details is shown in red.

Tungaloy B047
Insert Tur n L i n e - C h i p breaker Overview
Application JXF J10E

Application
Positive Positive
with hole with hole

0.394 0.394
Front-turning Insert

Back-turning Insert
0.315 0.315
ap (in)

ap (in)
0.236 0.236

- 0.157

0.078
- 0.157

0.078

0 0
0.0016 0.0032 0.0048 0.0064 0.0080 0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B156 f (ipr) B157, B158

JXB JXR
Application

Application
Positive Positive
with hole with hole

0.394

Reverse-turning Insert
0.394
Back-turning Insert

0.315 0.315
ap (in)

0.236

ap (in)
0.236

- 0.157

0.078
- 0.157

0.078
0 0
0.0016 0.0032 0.0048 0.0064 0.0080 0.0016 0.0032 0.0048 0.0064 0.0080
f (ipr) B156 f (ipr) B156

JTB RT
Application

Application

Positive Positive
with hole without hole
Special round
insert
0.200 0.394
Back-turning Insert

0.160 0.315
Medium cutting
ap (in)

0.120
ap (in)

0.236

- 0.080

0.040
- 0.157

0.078

0 0
0.0016 0.0032 0.0048 0.0064 0.0080 0.008 0.016 0.024 0.032 0.040
f (ipr) B157 f (ipr) B127

The page number for the product details is shown in red.

B048 www.tungaloyamerica.com
Tur n L i ne - C h i p b reaker Overview

Insert
S T
Application

Positive 11°
without hole
90° 60°
0.200

0.160

PS
Finishing to medium cutting

ap (in)

0.120

0.080

0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B145
0.200

0.160

23
ap (in)

0.120

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B132 B145
0.200
Medium cutting

24 0.160
ap (in)

0.120

0.080
0.2
0.008
0.040
6º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B145
0.200

0.160

CM
ap (in)

0.120

0.080

0.040
0.010
0.25
0
Finishing to medium cutting

0.004 0.008 0.012 0.016 0.020

10º

f (ipr) B132 B145

0.200

- 0.160
ap (in)

0.120
(with hand)
0.080

0.040
23º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B132 B146
0.200

- 0.160
ap (in)

0.120
M,G-class 0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B132 B146

The page number for the product details is shown in red.

Tungaloy B049
Insert Tur n L i n e - C h i p breaker Overview
Application D V W
Chipbreaker
Positive, double-sided
55° 35° 80°
0.200
(Low cutting force)

SS
ap (in) 0.160

0.120
Finishing

0.080

0.040
30º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B123 B154
0.200

TSW 0.160
ap (in)

0.120
Finishing
(Wiper)

0.080
0.1
0.004
0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B154
0.200

TS 0.160
medium cutting
Finishing to

ap (in)

0.120

0.080
0.1
0.004
0.040
10º

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B123 B154
0.100
Finishing (Low cutting
force) (sharp edge)

0.080

JSS
ap (in)

0.060

0.040

0.020

0
30º

0.002 0.004 0.006 0.008 0.010

f (ipr) B122, B123 B154
0.100
cutting (sharp edge)
Finishing to medium

0.080

JTS
ap (in)

0.060

0.040

0.1
0.004 0.020
10º

0
0.002 0.004 0.006 0.008 0.010
f (ipr) B122 B154
0.100

0.080

JRP
(sharp edge)

ap (in)

0.060
Finishing

0.040

0.020
23º

0
0.002 0.004 0.006 0.008 0.010
f (ipr) B122 B152

RCGX
Application

Chipbreaker
Positive, without hole
Special round
insert
0.200
Medium cutting

0.160

- 0.120
ap (in)

0.080

0.040

0
0.004 0.008 0.012 0.016 0.020
f (ipr) B128 The page number for the product details is shown in red.

B050 www.tungaloyamerica.com
JRP / JPP / JSP High Tolerance Inserts

Insert
Ground chipbreakers (Sharp edge)

JRP type JPP type JSP type

Lead (Ramp) type Parallel type Neutral (symmetric) type
chipbreaker chipbreaker chipbreaker
For excellent chip control Good chip evacuation
For profiling

Tolerance of inserts
Tolerance of Height of cutting edge:
corner radius:0 - -0.02 mm (0.0008") ±0.025 mm (0.001")
(Minus tolerance)
0
rε -0.02 mm
(0.0008")

±0.025 mm (0.001")

JS 3 dimensional chipbreaker

Excellent cutting performance for superalloys

Dynamic inclination
- Improved chip control
- Low cutting force prevents
dimensional changes
Steep protrusion
- Improved chip coiling for profile turning

Tungaloy B051
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H H C CL C CL CL CL C
M Stainless L C CL C C
K Cast iron CL CL C CL C CL CL CL C
Rhombic, 80° N Non-ferrous C
with hole S Superalloys C CL C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

NS520
AH120
GH110
AH110
T9105

T9135
T9125

T6130
T9115

TH10
Inch Metric
TF CNMG 431 TF CNMG120404-TF 0.016" 䖃 䖃

CNMG 432 TF CNMG120408-TF 0.031" 䖃

01 CNGG 320.5-01 CNGG090302-01 0.008" 䖃

Precision finishing

CNGG 321-01 CNGG090304-01 0.016" 䖃

CNGG 322-01 CNGG090308-01 0.031" 䖃

CNGG 430-01 CNGG120401-01 0.004" 䖃

CNGG 430.5-01 CNGG120402-01 0.008" 䖃 䖃 䖃 䖃

CNGG 431-01 CNGG120404-01 0.016" 䖃 䖃 䖃 䖃

CNGG 432-01 CNGG120408-01 0.031" 䖃 䖃 䖃 䖃

C CNGG 431 R-C CNGG120404R-C 0.016" 䖃 䖃

CNGG 431 L-C CNGG120404L-C 0.016" 䖃

CNGG 432 R-C CNGG120408R-C 0.031" 䖃

CNGG 432 L-C CNGG120408L-C 0.031" 䖃

TSF CNMG 331E TSF CNMG090404E-TSF 0.016" 䖃 䖃 䖃 䖃

C
CNMG 332E TSF CNMG090408E-TSF 0.031" 䖃 䖃 䖃 䖃
Finishing

CNMG 431 TSF CNMG120404-TSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 TSF CNMG120408-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 TSF CNMG120412-TSF 0.047" 䖃 䖃 䖃 䖃

FW CNMG331E-FW CNMG090404E-FW 0.016" 䖃 䖃 䖃 䖃 䖃

CNMG332E-FW CNMG090408E-FW 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG431-FW CNMG120404-FW 0.016" 䖃 䖃 䖃

Finishing (Wiper)

CNMG432-FW CNMG120408-FW 0.031" 䖃 䖃 䖃 䖃 䖃

AFW CNMG 431 AFW CNMG120404-AFW 0.016" 䖃 䖃 䖃 䖃

CNMG 432 AFW CNMG120408-AFW 0.031" 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

B052 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL LH H L H LH CL CL CL C

Insert
M Stainless C L L C L C
K Cast iron CL C L CL CL CL C
Rhombic, 80° N Non-ferrous C
with hole S Superalloys C L
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
AH8005
AH8015
Chipbreaker Designation

NS9530
GT9530
AH630

GT720
T9135
T9125

T6130
T6120

T5105
T5115
T9115

TH10
Inch Metric
ZF CNMG331E-ZF CNMG090404E-ZF 0.016" 䖃 䖃
CNMG 431 ZF CNMG120404-ZF 0.016" 䖃 䖃 䖃 䖃

CNMG 432 ZF CNMG120408-ZF 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG 433 ZF CNMG120412-ZF 0.047" 䖃

Finishing

11 CNMG 431 11 CNMG120404-11 0.016" 䖃 䖃 䖃

CNMG 432 11 CNMG120408-11 0.031" 䖃 䖃 䖃 䖃

17
Finishing of mild steels

CNMG 431 TN17 CNMG120404-17 0.016" 䖃

CNMG 432 TN17 CNMG120408-17 0.031" 䖃

SF CNMG 321 SF CNMG090304-SF 0.016" 䖃 䖃 䖃

CNMG 322 SF CNMG090308-SF 0.031" 䖃 䖃 䖃

CNMG 431 SF CNMG120404-SF 0.016" 䖃 䖃 䖃

C
CNMG 432 SF CNMG120408-SF 0.031" 䖃 䖃 䖃

CNMG 433 SF CNMG120412-SF 0.047" 䖃 䖃 䖃

CF CNMG 431 CF CNMG120404-CF 0.016" 䖃 䖃

Finishing

CNMG 432 CF CNMG120408-CF 0.031" 䖃 䖃

CNMG 433 CF CNMG120412-CF 0.047" 䖃 䖃

HRF CNMG 431 HRF CNMG120404-HRF 0.016" 䖃 䖃

CNMG 432 HRF CNMG120408-HRF 0.031" 䖃 䖃

CNMG 433 HRF CNMG120412-HRF 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

Tungaloy B053
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H H CL CL CL
M Stainless L
K Cast iron CL CL CL L CL CL CL
Rhombic, 80° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

NS520
T9105

T9135
T9125

T6130
T9115

T5115
T515
Inch Metric
TS CNMG 431 TS CNMG120404-TS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 TS CNMG120408-TS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

CNMG 433 TS CNMG120412-TS 0.047" 䖃 䖃 䖃

SW CNMG332E-SW CNMG090408E-SW 0.031" 䖃 䖃 䖃 䖃

Finishing to medium cutting (Wiper)

CNMG333E-SW CNMG090412E-SW 0.047" 䖃 䖃 䖃 䖃

CNMG432-SW CNMG120408-SW 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG433-SW CNMG120412-SW 0.047" 䖃 䖃 䖃 䖃 䖃

ASW CNMG 432 ASW CNMG120408-ASW 0.031" 䖃 䖃 䖃 䖃

CNMG 433 ASW CNMG120412-ASW 0.047" 䖃 䖃 䖃

AS CNMG 431 AS CNMG120404-AS 0.016" 䖃 䖃 䖃 䖃

small depth of cut

CNMG 432 AS CNMG120408-AS 0.031" 䖃 䖃 䖃 䖃 䖃

High feed,

CNMG 433 AS CNMG120412-AS 0.047" 䖃 䖃 䖃

C

CB CNMG 321 CB CNMG090304-CB 0.016" 䖃

(Double sided)

CNMG 322 CB CNMG090308-CB 0.031" 䖃

Boring

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

B054 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H L H LH H C CL L CL CL

Insert
M Stainless C L L H C CL L L CL
K Cast iron CL CL CL C CL L CL CL
Rhombic, 80° N Non-ferrous
with hole S Superalloys C CL C L
H Hard materials
Coated Cermet
Application

Corner
radius

Negative
NS9530
AH8015
Chipbreaker Designation

GH330
AH630
AH645

AH725
AH120
AH110
T9105

T9135
T9125

T6130
T6120
T9115

T515
Inch Metric
NS CNMG 431 NS CNMG120404-NS 0.016" 䖃

CNMG 432 NS CNMG120408-NS 0.031" 䖃 䖃 䖃

Finishing

SS CNMG 331E SS CNMG090404E-SS 0.016" 䖃 䖃

CNMG 332E SS CNMG090408E-SS 0.031" 䖃 䖃

CNMG 431 SS CNMG120404-SS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 SS CNMG120408-SS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 SS CNMG120412-SS 0.047" 䖃 䖃 䖃 䖃 䖃

TM CNMG 321 TM CNMG090304-TM 0.016" 䖃 䖃

CNMG 322 TM CNMG090308-TM 0.031" 䖃 䖃 䖃

CNMG 331E TM CNMG090404E-TM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 332E TM CNMG090408E-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 333E TM CNMG090412E-TM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

CNMG 431 TM CNMG120404-TM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 TM CNMG120408-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
CNMG 433 TM CNMG120412-TM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 434 TM CNMG120416-TM 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 543 TM CNMG160612-TM 0.047" 䖃 䖃 䖃 䖃 䖃

CNMG 642 TM CNMG190608-TM 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG 643 TM CNMG190612-TM 0.047" 䖃 䖃 䖃 䖃 䖃

AM CNMG 432 AM CNMG120408-AM 0.031" 䖃 䖃

Finishing to medium cutting

CNMG 433 AM CNMG120412-AM 0.047" 䖃 䖃

CNMG 434 AM CNMG120416-AM 0.063" 䖃 䖃

NM CNMG 432 NM CNMG120408-NM 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG 433 NM CNMG120412-NM 0.047" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

Tungaloy B055
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H C CL CL CL CL CL C
M Stainless C CL C
K Cast iron CL CL CL C L H C CL CL CL CL CL C
Rhombic, 80° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

NS520
AH120

GT720
AH110
T9105

T9135
T9125

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
TQ CNMG 431 TQ CNMG120404-TQ 0.016" 䖃 䖃
Finishing to medium cutting

CNMG 432 TQ CNMG120408-TQ 0.031" 䖃 䖃

ZM CNMG 332E-ZM CNMG090408E-ZM 0.031" 䖃 䖃

CNMG 432 ZM CNMG120408-ZM 0.031" 䖃 䖃 䖃 䖃 䖃

CNMG 433 ZM CNMG120412-ZM 0.047" 䖃 䖃 䖃 䖃

CNMG 434 ZM CNMG120416-ZM 0.063" 䖃 䖃

DM CNMG 431 DM CNMG120404-DM 0.016" 䖃 䖃

CNMG 432 DM CNMG120408-DM 0.031" 䖃 䖃 䖃 䖃

CNMG 433 DM CNMG120412-DM 0.047" 䖃 䖃 䖃 䖃

CNMG 543 DM CNMG160612-DM 0.047" 䖃

All-round CNMG 321 CNMG090304 0.016" 䖃 䖃 䖃

CNMG 322 CNMG090308 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

CNMG 431 CNMG120404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
CNMG 432 CNMG120408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 CNMG120412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 434 CNMG120416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 542 CNMG160608 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 543 CNMG160612 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 544 CNMG160616 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 642 CNMG190608 0.031" 䖃 䖃 䖃

CNMG 643 CNMG190612 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 644 CNMG190616 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

B056 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL LH H C CL L CL CL CL CL C

Insert
M Stainless C CL L CL CL C
K Cast iron CL C CL L CL CL CL CL C
Rhombic, 80° N Non-ferrous C
with hole S Superalloys C CL C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
Chipbreaker Designation

GH330
AH905
AH725
AH120

GT720
AH110
T9135
T9125
T9115

TH10
Inch Metric
27 CNMG 431 TN27 CNMG120404-27 0.016" 䖃 䖃 䖃 䖃
Finishing to medium

CNMG 432 TN27 CNMG120408-27 0.031" 䖃 䖃 䖃 䖃 䖃

cutting

CNMG 433 TN27 CNMG120412-27 0.047" 䖃

28 CNGP 430-28 CNGP120401-28 0.004" 䖃 䖃 䖃

CNGP 430.5-28 CNGP120402-28 0.008" 䖃 䖃 䖃

CNGP 431-28 CNGP120404-28 0.016" 䖃 䖃 䖃

CNGP 432-28 CNGP120408-28 0.031" 䖃 䖃 䖃

CNMG 431 TN28 CNMG120404-28 0.016" 䖃 䖃 䖃

CNMG 432 TN28 CNMG120408-28 0.031" 䖃 䖃 䖃

CNMG 433 TN28 CNMG120412-28 0.047" 䖃

33 CNMG 432 TN33 CNMG120408-33 0.031" 䖃 䖃

Medium cutting

CNMG 434 TN33 CNMG120416-33 0.063" 䖃

CNMG 543 TN33 CNMG160612-33 0.047" 䖃

CNMG 643 TN33 CNMG190612-33 0.047" 䖃

C

37 CNMG 431 TN37 CNMG120404-37 0.016" 䖃 䖃

CNMG 432 TN37 CNMG120408-37 0.031" 䖃 䖃 䖃 䖃

CNMG 433 TN37 CNMG120412-37 0.047" 䖃

38 CNMG 431 TN38 CNMG120404-38 0.016" 䖃 䖃 䖃 䖃

CNMG 432 TN38 CNMG120408-38 0.031" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B208 - Internal toolholders → B321 -
J series toolholders → B376 TungCap → B223 -, F006 -

Tungaloy B057
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel L H LH H L C CL C
M Stainless C L L H L C L C C
K Cast iron CL C L H L C CL C C
Rhombic, 80° N Non-ferrous C C
with hole S Superalloys C C L L C C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius
Negative

AH8005

NS9530
AH8015
Chipbreaker Designation

AH905
AH630
AH645

KS05F
AH725

GH110
T6130
T6120

T5105

T5125
T5115

TH10
T515
Inch Metric
SM CNMG 331E-SM CNMG090404E-SM 0.016" 䖃 䖃 䖃
CNMG 332E-SM CNMG090408E-SM 0.031" 䖃 䖃 䖃
CNMG 333E-SM CNMG090412E-SM 0.047" 䖃 䖃 䖃
CNMG 431 SM CNMG120404-SM 0.016" 䖃 䖃 䖃 䖃 䖃

CNMG 432 SM CNMG120408-SM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 SM CNMG120412-SM 0.047" 䖃 䖃 䖃 䖃 䖃

Medium cutting

CM CNMG 431 CM CNMG120404-CM 0.016" 䖃 䖃 䖃

CNMG 432 CM CNMG120408-CM 0.031" 䖃 䖃 䖃 䖃

CNMG 433 CM CNMG120412-CM 0.047" 䖃 䖃 䖃 䖃

CNMG 542 CM CNMG160608-CM 0.031" 䖃 䖃 䖃

CNMG 543 CM CNMG160612-CM 0.047" 䖃 䖃 䖃

P CNGG 431 R-P CNGG120404R-P 0.016" 䖃 䖃 䖃

CNGG 431 L-P CNGG120404L-P 0.016" 䖃 䖃 䖃

CNGG 432 R-P CNGG120408R-P 0.031" 䖃 䖃

CNGG 432 L-P CNGG120408L-P 0.031" 䖃 䖃

C
Finishing to medium cutting

HRM CNMG 431 HRM CNMG120404-HRM 0.016" 䖃 䖃

CNMG 432 HRM CNMG120408-HRM 0.031" 䖃 䖃

CNMG 433 HRM CNMG120412-HRM 0.047" 䖃 䖃

CNMG 542 HRM CNMG160608-HRM 0.031" 䖃 䖃

CNMG 543 HRM CNMG160612-HRM 0.047" 䖃 䖃

CNMG 643 HRM CNMG190612-HRM 0.047" 䖃 䖃

CNMG 644 HRM CNMG190616-HRM 0.063" 䖃 䖃

HMM CNMG 431 HMM CNMG120404-HMM 0.016" 䖃

CNMG 432 HMM CNMG120408-HMM 0.031" 䖃 䖃

Medium cutting

CNMG 433 HMM CNMG120412-HMM 0.047" 䖃

CNMG 542 HMM CNMG160608-HMM 0.031" 䖃

CNMG 543 HMM CNMG160612-HMM 0.047" 䖃

CNMG 544 HMM CNMG160616-HMM 0.063" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B294 -
J series toolholders → B376 TungCap → B223 -, F006 -

B058 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H L H LH H C CL CL CL CL

Insert
M Stainless C L L H C CL CL
K Cast iron CL CL C CL CL CL CL LH
Rhombic, 80° N Non-ferrous LH
with hole S Superalloys C CL LH
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
Chipbreaker Designation

GH330
AH630
AH645

AH120

GT720
AH110
T9105

T9135
T9125

T6130
T6120
T9115

KS20
Inch Metric
SA CNMG 431 SA CNMG120404-SA 0.016" 䖃 䖃 䖃 䖃 䖃

CNMG 432 SA CNMG120408-SA 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 SA CNMG120412-SA 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 643 SA CNMG190612-SA 0.047" 䖃 䖃

Medium cutting

CNMG 644 SA CNMG190616-SA 0.063" 䖃 䖃

S CNMG 431 R-S CNMG120404R-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 431 L-S CNMG120404L-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 R-S CNMG120408R-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 432 L-S CNMG120408L-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TH CNMG 432 TH CNMG120408-TH 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 433 TH CNMG120412-TH 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

CNMG 434 TH CNMG120416-TH 0.063" 䖃 䖃 䖃 䖃

CNMG 543 TH CNMG160612-TH 0.047" 䖃 䖃 䖃 䖃 䖃

CNMG 544 TH CNMG160616-TH 0.063" 䖃 䖃 䖃 䖃 䖃

CNMG 643 TH CNMG190612-TH 0.047" 䖃 䖃 䖃 䖃 䖃

Medium to heavy cutting

CNMG 644 TH CNMG190616-TH 0.063" 䖃 䖃 䖃 䖃 䖃

C

THS CNMG 432 THS CNMG120408-THS 0.031" 䖃 䖃 䖃 䖃

CNMG 433 THS CNMG120412-THS 0.047" 䖃 䖃 䖃 䖃

CNMG 434 THS CNMG120416-THS 0.063" 䖃 䖃 䖃 䖃

CNMG 543 THS CNMG160612-THS 0.047" 䖃 䖃 䖃 䖃

CNMG 544 THS CNMG160616-THS 0.063" 䖃 䖃 䖃 䖃

CNMG 643 THS CNMG190612-THS 0.047" 䖃 䖃 䖃

CNMG 644 THS CNMG190616-THS 0.063" 䖃 䖃 䖃

CNMG 646 THS CNMG190624-THS 0.094" 䖃 䖃 䖃

CNMG 866 THS CNMG250924-THS 0.094" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B208 - Internal toolholders → B321 -
J series toolholders → B376 TungCap → B223 -, F006 -

Tungaloy B059
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL LH H H LH H
M Stainless L L H
K Cast iron CL CL C L H
Rhombic, 80° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated
Application

Corner
radius
Negative

Chipbreaker Designation

AH630
AH645
T9135
T9125

T6130

T5105

T5125
T9115

T5115
T515
Inch Metric
TRS CNMM 432 TRS CNMM120408-TRS 0.031" 䖃 䖃 䖃
Medium to heavy cutting

CNMM 433 TRS CNMM120412-TRS 0.047" 䖃 䖃 䖃

CNMM160612-TRS 0.047" 䖃 䖃 䖃
(Single sided)

CNMM 543 TRS

CNMM 544 TRS CNMM160616-TRS 0.063" 䖃 䖃 䖃
CNMM 644 TRS CNMM190616-TRS 0.063" 䖃 䖃 䖃
CNMM 646 TRS CNMM190624-TRS 0.094" 䖃 䖃 䖃
CNMM 866 TRS CNMM250924-TRS 0.094" 䖃 䖃 䖃

TU CNMM 643 TU CNMM190612-TU 0.047" 䖃 䖃

CNMM 644 TU CNMM190616-TU 0.063" 䖃 䖃

CNMM 646 TU CNMM190624-TU 0.094" 䖃 䖃 䖃

Heavy cutting (Single sided)

CNMM 866 TU CNMM250924-TU 0.094" 䖃 䖃

TUS CNMM 642 TUS CNMM190608-TUS 0.031" 䖃 䖃

CNMM 643 TUS CNMM190612-TUS 0.047" 䖃 䖃 䖃
CNMM 644 TUS CNMM190616-TUS 0.063" 䖃 䖃 䖃
CNMM 646 TUS CNMM190624-TUS 0.094" 䖃 䖃 䖃
CNMM 648 TUS CNMM190632-TUS 0.125" 䖃 䖃
C CNMM 864 TUS CNMM250916-TUS 0.063" 䖃 䖃 䖃
CNMM 866 TUS CNMM250924-TUS 0.094" 䖃 䖃 䖃
CNMM 868 TUS CNMM250932-TUS 0.125" 䖃 䖃

SH CNMG 432 SH CNMG120408-SH 0.031" 䖃 䖃 䖃

CNMG 433 SH CNMG120412-SH 0.047" 䖃 䖃 䖃

CNMG 434 SH CNMG120416-SH 0.063" 䖃 䖃 䖃

CNMG 543 SH CNMG160612-SH 0.047" 䖃 䖃 䖃

CNMG 544 SH CNMG160616-SH 0.063" 䖃 䖃 䖃

Medium to heavy cutting

CNMG 643 SH CNMG190612-SH 0.047" 䖃 䖃 䖃

CNMG 644 SH CNMG190616-SH 0.063" 䖃 䖃 䖃

CH CNMG 431 CH CNMG120404-CH 0.016" 䖃 䖃 䖃

CNMG 432 CH CNMG120408-CH 0.031" 䖃 䖃 䖃 䖃

CNMG 433 CH CNMG120412-CH 0.047" 䖃 䖃 䖃 䖃

CNMG 543 CH CNMG160612-CH 0.047" 䖃 䖃 䖃

CNMG 544 CH CNMG160616-CH 0.063" 䖃 䖃 䖃

CNMG 643 CH CNMG190612-CH 0.047" 䖃 䖃 䖃

CNMG 644 CH CNMG190616-CH 0.063" 䖃 䖃 䖃

Reference pages
䖃㻌: Line up
External toolholders → B208 - Internal toolholders → B321 -
J series toolholders → B376 TungCap → B223 -, F006 -

B060 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL C

Insert
M Stainless C
K Cast iron CL CL C L H CL C CL C
Rhombic, 80° N Non-ferrous C
with hole S Superalloys
H Hard materials C
Coated Cermet Uncoated Ceramics
Application

Corner
radius

Negative
Chipbreaker Designation

NS520

FX105
T9105

T5105

T5125
T5115

LX21
TH10

LX11
T515
Inch Metric
- CNMA 431 CNMA120404 0.016" 䖃 䖃 䖃 䖃

CNMA 432 CNMA120408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMA 433 CNMA120412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CNMA 434 CNMA120416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃

CNMA 542 CNMA160608 0.031" 䖃 䖃 䖃

CNMA 543 CNMA160612 0.047" 䖃 䖃 䖃 䖃

CNMA 544 CNMA160616 0.063" 䖃 䖃 䖃 䖃

Finishing to medium cutting

CNMA 643 CNMA190612 0.047" 䖃 䖃 䖃 䖃

CNMA 644 CNMA190616 0.063" 䖃 䖃 䖃 䖃

Wiper CNMA 432 W CNMA120408W 0.031" 䖃

CNMA 433 W CNMA120412W 0.047" 䖃

CNMA 434 W CNMA120416W 0.063" 䖃

- CNGA 431 CNGA120404 0.016" 䖃 䖃

CNGA 432 CNGA120408 0.031" 䖃 䖃 䖃 䖃

CNGA 433 CNGA120412 0.047" 䖃 䖃 䖃

C
CNGA 434 CNGA120416 0.063" 䖃 䖃

CNGA 435 CNGA120420 0.078" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B208 - Internal toolholders → B321 -
TungCap → B223 -, F006 -

Tungaloy B061
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel
M Stainless
K Cast iron CL C CL
Rhombic, 80° N Non-ferrous
without hole S Superalloys
H Hard materials C
Ceramics
Application

Corner
radius
Negative

Chipbreaker Designation

CX710
FX105
LX21
LX11
Inch Metric
- CNGD 453 CNGD120712 0.047" 䖃

CNGD 454 CNGD120716 0.063" 䖃

- CNMN 432 CNMN120408 0.031" 䖃

Finishing to medium cutting

CNMN 433 CNMN120412 0.047" 䖃

- CNGN 431 CNGN120404 0.016" 䖃

CNGN 432 CNGN120408 0.031" 䖃 䖃

CNGN 433 CNGN120412 0.047" 䖃 䖃

CNGN 434 CNGN120416 0.063" 䖃 䖃 䖃

CNGN 435 CNGN120420 0.078" 䖃

CNGN 452 CNGN120708 0.031" 䖃 䖃

CNGN 453 CNGN120712 0.047" 䖃 䖃

CNGN 454 CNGN120716 0.063" 䖃 䖃

C
CNGN 455 CNGN120720 0.078" 䖃

䖃㻌: Line up

Reference pages
CNGD... : External toolholders → B271
CNMN..., CNGN... : External toolholders → B246, Internal toolholders → B341

B062 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H CL C CL CL CL CL C

Insert
M Stainless CL C C
K Cast iron CL CL CL C CL CL CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys CL C
H Hard materials
Coated Coated cermet Cermet Uncoated
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
AH120

GT720
GH110
T9105

T9135
T9125
T9115

TH10
Inch Metric
TF DNMG 431 TF DNMG150404-TF 0.016" 䖃 䖃 䖃

DNMG 432 TF DNMG150408-TF 0.031" 䖃

Precision finishing

01 DNGG 330.5-01 DNGG110402-01 0.008" 䖃

DNGG 331-01 DNGG110404-01 0.016" 䖃 䖃

DNGG 332-01 DNGG110408-01 0.031" 䖃 䖃

DNGG 430.5-01 DNGG150402-01 0.008" 䖃 䖃 䖃

DNGG 431-01 DNGG150404-01 0.016" 䖃 䖃 䖃 䖃

DNGG 432-01 DNGG150408-01 0.031" 䖃 䖃 䖃 䖃

TSF DNMG 331E-TSF DNMG110404E-TSF 0.016" 䖃 䖃 䖃 䖃

DNGG 332E-TSF DNMG110408E-TSF 0.031" 䖃 䖃 䖃 䖃

DNGG 333E-TSF DNMG110412E-TSF 0.047" 䖃 䖃 䖃 䖃

DNMG 431 TSF DNMG150404-TSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

DNMG 432 TSF DNMG150408-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 433 TSF DNMG150412-TSF 0.047" 䖃 䖃 䖃 䖃 䖃

DNMG 441 TSF DNMG150604-TSF 0.016" 䖃 䖃 䖃 䖃

DNMG 442 TSF DNMG150608-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 D

DNMG 443 TSF DNMG150612-TSF 0.047" 䖃 䖃 䖃 䖃

FW DNMG 331E-FW DNMG110404E-FW 0.016" 䖃

Finishing (Wiper)

DNMG 332E-FW DNMG110408E-FW 0.031" 䖃

DNMG 431 FW DNMG150404-FW 0.016" 䖃

DNMG 432 FW DNMG150408-FW 0.031" 䖃

DNMG 441 FW DNMG150604-FW 0.016" 䖃

DNMG 442 FW DNMG150608-FW 0.031" 䖃

ZF DNMG331E-ZF DNMG110404E-ZF 0.016" 䖃 䖃

DNMG 431 ZF DNMG150404-ZF 0.016" 䖃 䖃 䖃 䖃 䖃

DNMG 432 ZF DNMG150408-ZF 0.031" 䖃 䖃 䖃 䖃 䖃

Finishing

DNMG 433 ZF DNMG150412-ZF 0.047" 䖃 䖃 䖃

DNMG 441 ZF DNMG150604-ZF 0.016" 䖃 䖃

DNMG 442 ZF DNMG150608-ZF 0.031" 䖃 䖃 䖃

DNMG 443 ZF DNMG150612-ZF 0.047" 䖃 䖃

䖃㻌: Line up
Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223 -, F008 -

Tungaloy B063
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL L H LH CL CL C
M Stainless C L L C L CL C
K Cast iron CL C L CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys C L
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius
Negative

AH8005

NS9530
AH8015
Chipbreaker Designation

GH330
AH630
T6130
T6120

T5105
T9115

T5115

TH10
Inch Metric
11 DNMG 331 TN11 DNMG110404-11 0.016" 䖃

DNMG 332 TN11 DNMG110408-11 0.031" 䖃

Finishing

DNMG 431 TN11 DNMG150404-11 0.016" 䖃 䖃 䖃

DNMG 432 TN11 DNMG150408-11 0.031" 䖃 䖃

17 DNMG 431 TN17 DNMG150404-17 0.016" 䖃

Finishing of mild

DNMG 432 TN17 DNMG150408-17 0.031" 䖃

steels

SF DNMG 431 SF DNMG150404-SF 0.016" 䖃 䖃 䖃

DNMG 432 SF DNMG150408-SF 0.031" 䖃 䖃 䖃

DNMG 441 SF DNMG150604-SF 0.016" 䖃 䖃 䖃

DNMG 442 SF DNMG150608-SF 0.031" 䖃 䖃 䖃

CF DNMG 431 CF DNMG150404-CF 0.016" 䖃 䖃

DNMG 432 CF DNMG150408-CF 0.031" 䖃 䖃

Finishing

DNMG 433 CF DNMG150412-CF 0.047" 䖃 䖃

DNMG 441 CF DNMG150604-CF 0.016" 䖃 䖃

D DNMG 442 CF DNMG150608-CF 0.031" 䖃 䖃

DNMG 443 CF DNMG150612-CF 0.047" 䖃 䖃

HRF DNMG 431 HRF DNMG150404-HRF 0.016" 䖃 䖃

DNMG 432 HRF DNMG150408-HRF 0.031" 䖃 䖃

DNMG 441 HRF DNMG150604-HRF 0.016" 䖃 䖃

DNMG 442 HRF DNMG150608-HRF 0.031" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223 -, F008 -

B064 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H CL CL CL

Insert
M Stainless
K Cast iron CL CL CL CL CL
Rhombic, 55° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
T9105

T9135
T9125
T9115
Inch Metric
TS DNMG 332 TS DNMG110408-TS 0.031" 䖃

DNMG 431 TS DNMG150404-TS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing

DNMG 432 TS DNMG150408-TS

DNMG 433 TS DNMG150412-TS 0.047" 䖃 䖃 䖃 䖃

DNMG 441 TS DNMG150604-TS 0.016" 䖃 䖃 䖃

DNMG 442 TS DNMG150608-TS 0.031" 䖃 䖃 䖃 䖃 䖃

DNMG 443 TS DNMG150612-TS 0.047" 䖃 䖃

SW DNMG 332E-SW DNMG110408E-SW 0.031" 䖃

Finishing to medium cutting

DNMG 333E-SW DNMG110412E-SW 0.047" 䖃

DNMG 432 SW DNMG150408-SW 0.031" 䖃

(Wiper)

DNMG 433 SW DNMG150412-SW 0.047" 䖃

DNMG 442 SW DNMG150608-SW 0.031" 䖃

DNMG 443 SW DNMG150612-SW 0.047" 䖃

High feed, small depth of cut

AS DNMG 431 AS DNMG150404-AS 0.016" 䖃 䖃 䖃

DNMG 432 AS DNMG150408-AS 0.031" 䖃 䖃 䖃 䖃

DNMG 433 AS DNMG150412-AS 0.047" 䖃 䖃 䖃 䖃

DNMG 441 AS DNMG150604-AS 0.016" 䖃

DNMG 442 AS DNMG150608-AS 0.031" 䖃 䖃

DNMG 443 AS DNMG150612-AS 0.047" 䖃 D

CB DNMG 331 CB DNMG110404-CB 0.016" 䖃 䖃 䖃

(Double sided)

DNMG 332 CB DNMG110408-CB 0.031" 䖃 䖃 䖃

Boring

NS DNMG 431 NS DNMG150404-NS 0.016" 䖃 䖃

Finishing

DNMG 432 NS DNMG150408-NS 0.031" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223, F008 -

Tungaloy B065
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H L H LH H C CL CL CL CL
M Stainless C L L H C CL CL
K Cast iron CL CL C CL CL CL CL LH
Rhombic, 55° N Non-ferrous LH
with hole S Superalloys C CL LH
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

GH330
AH630
AH645

AH120
AH110
T9105

T9135
T9125

T6130
T6120
T9115

KS20
Inch Metric
SS DNMG 331E SS DNMG110404E-SS 0.016" 䖃 䖃

DNMG 332E SS DNMG110408E-SS 0.031" 䖃 䖃

DNMG 431 SS DNMG150404-SS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 432 SS DNMG150408-SS 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

0.031"

DNMG 433 SS DNMG150412-SS 0.047" 䖃 䖃 䖃 䖃 䖃

DNMG 441 SS DNMG150604-SS 0.016" 䖃 䖃 䖃 䖃 䖃

DNMG 442 SS DNMG150608-SS 0.031" 䖃 䖃 䖃 䖃 䖃

DNMG 443 SS DNMG150612-SS 0.047" 䖃 䖃 䖃 䖃

TM DNMG 331E TM DNMG110404E-TM 0.016" 䖃 䖃

DNMG 332E TM DNMG110408E-TM 0.031" 䖃 䖃

DNMG 333E TM DNMG110412E-TM 0.047" 䖃 䖃

DNMG 331 TM DNMG110404-TM 0.016" 䖃 䖃 䖃

DNMG 332 TM DNMG110408-TM 0.031" 䖃 䖃 䖃

Medium cutting

DNMG 431 TM DNMG150404-TM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 432 TM DNMG150408-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 433 TM DNMG150412-TM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 434 TM DNMG150416-TM 0.063" 䖃 䖃

DNMG 441 TM DNMG150604-TM 0.016" 䖃 䖃 䖃 䖃 䖃

D DNMG 442 TM DNMG150608-TM 0.031" 䖃 䖃 䖃 䖃 䖃

DNMG 443 TM DNMG150612-TM 0.047" 䖃 䖃 䖃 䖃 䖃

DNMG 444 TM DNMG150616-TM 0.063" 䖃 䖃 䖃 䖃

AM DNMG 432 AM DNMG150408-AM 0.031" 䖃 䖃

DNMG 433 AM DNMG150412-AM 0.047" 䖃 䖃

Finishing to medium cutting

DNMG 434 AM DNMG150416-AM 0.063" 䖃 䖃

DNMG 442 AM DNMG150608-AM 0.031" 䖃 䖃

DNMG 443 AM DNMG150612-AM 0.047" 䖃 䖃

DNMG 444 AM DNMG150616-AM 0.063" 䖃 䖃

NM DNMG 432 NM DNMG150408-NM 0.031" 䖃 䖃 䖃 䖃 䖃

DNMG 433 NM DNMG150412-NM 0.047" 䖃 䖃 䖃

DNMG 442 NM DNMG150608-NM 0.031" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223, F008 -

B066 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H C CL CL CL CL C

Insert
M Stainless C CL C
K Cast iron CL CL CL C L H C CL CL CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
AH120
AH110
T9105

T9135
T9125

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
TQ DNMG 431 TQ DNMG150404-TQ 0.016" 䖃 䖃

DNMG 432 TQ DNMG150408-TQ 0.031" 䖃 䖃

Finishing to medium cutting

ZM DNMG 332E-ZM DNMG110408E-ZM 0.031" 䖃 䖃

DNMG 432 ZM DNMG150408-ZM 0.031" 䖃 䖃 䖃 䖃 䖃

DNMG 433 ZM DNMG150412-ZM 0.047" 䖃 䖃 䖃

DNMG 442 ZM DNMG150608-ZM 0.031" 䖃 䖃 䖃

DNMG 443 ZM DNMG150612-ZM 0.047" 䖃 䖃

DM DNMG 432 DM DNMG150408-DM 0.031" 䖃 䖃 䖃

DNMG 433 DM DNMG150412-DM 0.047" 䖃 䖃 䖃 䖃

DNMG 441 DM DNMG150604-DM 0.016" 䖃

DNMG 442 DM DNMG150608-DM 0.031" 䖃 䖃 䖃

DNMG 443 DM DNMG150612-DM 0.047" 䖃 䖃 䖃 䖃

DNMG 444 DM DNMG150616-DM 0.063" 䖃

Medium cutting

All-round DNMG 331 DNMG110404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 332 DNMG110408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 D

DNMG 431 DNMG150404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 432 DNMG150408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 433 DNMG150412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 434 DNMG150416 0.063" 䖃 䖃 䖃 䖃 䖃

DNMG 441 DNMG150604 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 442 DNMG150608 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 443 DNMG150612 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 444 DNMG150616 0.063" 䖃 䖃

䖃 䖃
Finishing to medium

27 DNMG 431 27 DNMG150404-27 0.016"

DNMG 432 27 DNMG150408-27 0.031" 䖃 䖃 䖃

cutting

DNMG 433 27 DNMG150412-27 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223, F008 -

Tungaloy B067
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL L H LH H C CL CL CL CL C
M Stainless C L L H C CL CL C
K Cast iron CL C CL CL CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

GH330
AH630
AH645

AH120
AH110
T6130
T6120
T9115

TH10
Inch Metric
28 DNMG 431 TN28 DNMG150404-28 0.016" 䖃 䖃

DNMG 432 TN28 DNMG150408-28 0.031" 䖃 䖃

33 DNMG 431 33 DNMG150404-33 0.016" 䖃

DNMG 432 33 DNMG150408-33 0.031" 䖃 䖃

37 DNMG 431 37 DNMG150404-37 0.016" 䖃

DNMG 432 37 DNMG150408-37 0.031" 䖃 䖃

Medium cutting

38 DNMG 433 38 DNMG150412-38 0.047" 䖃

D
Parallel DNGG 431 R DNGG150404R 0.016" 䖃 䖃

DNGG 431 L DNGG150404L 0.016" 䖃 䖃

DNGG 432 R DNGG150408R 0.031" 䖃

DNGG 432 L DNGG150408L 0.031" 䖃

SM DNMG 331E SM DNMG110404E-SM 0.016" 䖃 䖃 䖃

DNMG 332E SM DNMG110408E-SM 0.031" 䖃 䖃 䖃

DNMG 431 SM DNMG150404-SM 0.016" 䖃 䖃 䖃 䖃

DNMG 432 SM DNMG150408-SM 0.031" 䖃 䖃 䖃 䖃

DNMG 433 SM DNMG150412-SM 0.047" 䖃 䖃 䖃 䖃

DNMG 441 SM DNMG150604-SM 0.016" 䖃 䖃 䖃 䖃

DNMG 442 SM DNMG150608-SM 0.031" 䖃 䖃 䖃 䖃

DNMG 443 SM DNMG150612-SM 0.047" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B204 - Internal toolholders → B296 -
J series toolholders → B376 TungCap → B223, F008 -

B068 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel LH H H LH H C CL C CL CL C

Insert
M Stainless L L H C CL C L C CL C
K Cast iron CL C L H C CL C CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys C CL C L L C
H Hard materials
Coated Un-
Cermet coated
Application

Corner
radius

Negative
AH8005

NS9530
AH8015
Chipbreaker Designation

AH630
AH645

GH330
AH905
AH120

GH110
T9125
T9135
T6130

AH110
T5105

T5125
T5115

TH10
T515
Inch Metric
CM DNMG 431 CM DNMG150404-CM 0.016" 䖃 䖃 䖃
DNMG 432 CM DNMG150408-CM 0.031" 䖃 䖃 䖃 䖃

DNMG 433 CM DNMG150412-CM 0.047" 䖃 䖃 䖃 䖃

DNMG 441 CM DNMG150604-CM 0.016" 䖃 䖃 䖃

DNMG 442 CM DNMG150608-CM 0.031" 䖃 䖃 䖃
Medium cutting

DNMG 443 CM DNMG150612-CM 0.047" 䖃 䖃 䖃

P DNGG 430.5 FRP DNGG150402R-P 0.008" 䖃 䖃

DNGG 430.5 FLP DNGG150402L-P 0.008" 䖃 䖃
DNGG 431 FRP DNGG150404R-P 0.016" 䖃 䖃
DNGG 431 FLP DNGG150404L-P 0.016" 䖃 䖃
DNGG 432 FRP DNGG150408R-P 0.031" 䖃
DNGG 432 FLP DNGG150408L-P 0.031" 䖃

HRM DNMG 431 HRM DNMG150404-HRM 0.016" 䖃 䖃

Finishing to medium

DNMG 432 HRM DNMG150408-HRM 0.031" 䖃 䖃

DNMG 433 HRM DNMG150412-HRM 0.047" 䖃 䖃

cutting

DNMG 441 HRM DNMG150604-HRM 0.016" 䖃 䖃

DNMG 442 HRM DNMG150608-HRM 0.031" 䖃 䖃

DNMG 443 HRM DNMG150612-HRM 0.047" 䖃 䖃

D
HMM DNMG 431 HMM DNMG150404-HMM 0.016" 䖃

DNMG 432 HMM DNMG150408-HMM 0.031" 䖃

DNMG 433 HMM DNMG150412-HMM 0.047" 䖃

SA DNMG 431 SA DNMG150404-SA 0.016" 䖃 䖃

DNMG 432 SA DNMG150408-SA 0.031" 䖃 䖃

DNMG 441 SA DNMG150604-SA 0.016" 䖃

Medium cutting

DNMG 442 SA DNMG150608-SA 0.031" 䖃

S DNMG 431 R-S DNMG150404R-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMG 431 L-S DNMG150404L-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃
DNMG 432 R-S DNMG150408R-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃
DNMG 432 L-S DNMG150408L-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃
DNMG 441 R-S DNMG150604R-S 0.016" 䖃 䖃 䖃 䖃 䖃
DNMG 441 L-S DNMG150604L-S 0.016" 䖃 䖃 䖃 䖃 䖃
DNMG 442 R-S DNMG150608R-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃
DNMG 442 L-S DNMG150608L-S 0.031" 䖃 䖃 䖃 䖃 䖃

Reference pages
䖃㻌: Line up
External toolholders → B210 - Internal toolholders → B324 -
J series toolholders → B376 TungCap → B223, F008 -

Tungaloy B069
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL LH H H LH H CL CL CL C
M Stainless L L H CL C
K Cast iron CL CL C L H CL CL CL C CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys CL
H Hard materials C
Coated Coated Cermet Un- Ceramics
cermet coated
Application

Corner
radius
Negative

Chipbreaker Designation

AH630
AH645

NS520
AH120
GT720

FX105
T9135
T9125

T6130

T5105

T5125
T9115

T5115

LX21
TH10

LX11
T515
Inch Metric
TH DNMG 432 TH DNMG150408-TH 0.031" 䖃 䖃 䖃 䖃
DNMG 433 TH DNMG150412-TH 0.047" 䖃 䖃 䖃 䖃
DNMG 434 TH DNMG150416-TH 0.063" 䖃 䖃
DNMG 442 TH DNMG150608-TH 0.031" 䖃 䖃 䖃 䖃
DNMG 443 TH DNMG150612-TH 0.047" 䖃 䖃 䖃 䖃
DNMG 444 TH DNMG150616-TH 0.063" 䖃 䖃 䖃

THS DNMG 432 THS DNMG150408-THS 0.031" 䖃 䖃 䖃

DNMG 433 THS DNMG150412-THS 0.047" 䖃 䖃 䖃
DNMG 434 THS DNMG150416-THS 0.063" 䖃 䖃
Medium to heavy cutting

DNMG 442 THS DNMG150608-THS 0.031" 䖃 䖃 䖃

DNMG 443 THS DNMG150612-THS 0.047" 䖃 䖃 䖃
DNMG 444 THS DNMG150616-THS 0.063" 䖃 䖃

SH DNMG 432 SH DNMG150408-SH 0.031" 䖃 䖃 䖃

DNMG 433 SH DNMG150412-SH 0.047" 䖃 䖃 䖃
DNMG 434 SH DNMG150416-SH 0.063" 䖃 䖃 䖃
DNMG 442 SH DNMG150608-SH 0.031" 䖃 䖃 䖃
DNMG 443 SH DNMG150612-SH 0.047" 䖃 䖃 䖃

D CH DNMG 431 CH DNMG150404-CH 0.016" 䖃 䖃 䖃

DNMG 432 CH DNMG150408-CH 0.031" 䖃 䖃 䖃 䖃
DNMG 433 CH DNMG150412-CH 0.047" 䖃 䖃 䖃 䖃
DNMG 441 CH DNMG150604-CH 0.016" 䖃 䖃 䖃
DNMG 442 CH DNMG150608-CH 0.031" 䖃 䖃 䖃
DNMG 443 CH DNMG150612-CH 0.047" 䖃 䖃 䖃

- DNMA 431 DNMA150404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DNMA 432 DNMA150408 0.031" 䖃 䖃 䖃 䖃 䖃
DNMA 433 DNMA150412 0.047" 䖃 䖃 䖃
DNMA 441 DNMA150604 0.016" 䖃 䖃 䖃 䖃
Finishing to medium cutting

DNMA 442 DNMA150608 0.031" 䖃 䖃 䖃 䖃

DNMA 443 DNMA150612 0.047" 䖃 䖃 䖃

- DNGA 431 DNGA150404 0.016" 䖃 䖃 䖃 䖃

DNGA 432 DNGA150408 0.031" 䖃 䖃 䖃 䖃 䖃
DNGA 433 DNGA150412 0.047" 䖃 䖃 䖃
DNGA 434 DNGA150416 0.063" 䖃
DNGA 442 DNGA150608 0.031" 䖃
DNGA 443 DNGA150612 0.047" 䖃
DNGA 444 DNGA150616 0.063" 䖃
DNGA 445 DNGA150620 0.078" 䖃

䖃㻌: Line up

B070 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel

Insert
M Stainless
K Cast iron CL
Rhombic, 55° N Non-ferrous
without hole S Superalloys
H Hard materials C
Ceramics
Application

Corner
radius

Negative
Chipbreaker Designation

FX105
LX11
Inch Metric
- DNGD 452 DNGD150708 0.031" 䖃

DNGD 453 DNGD150712 0.047" 䖃

DNGD 454 DNGD150716 0.063" 䖃

Finishing to medium cutting

- DNGN 431 DNGN150404 0.016" 䖃

DNGN 432 DNGN150408 0.031" 䖃

DNGN 433 DNGN150412 0.047" 䖃 䖃

DNGN 434 DNGN150416 0.063" 䖃

DNGN 452 DNGN150708 0.031" 䖃

DNGN 453 DNGN150712 0.047" 䖃

DNGN 454 DNGN150716 0.063" 䖃

- DNMX 454 DNMX150716 0.063" 䖃

䖃㻌: Line up
D

Reference pages
External toolholders → B210 - Internal toolholders → B324 -
J series toolholders → B376 TungCap → B223, F008 -
DNGD... : External toolholders → B271 -
DNGN... : External toolholders → B247

Tungaloy B071
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H CL C
M Stainless CL C
K Cast iron CL CL CL C
Round, N Non-ferrous C
with hole S Superalloys CL
H Hard materials C
Coated Uncoated Ceramics
Application

Corner
radius
Negative

Chipbreaker Designation

AH120
T9105
T9115
T9125
T9135

TH10

LX11
Inch Metric
61 RNMG 32 TN61 RNMG090300-61 - 䖃 䖃
Heavy cutting

RNMG 43 TN61 RNMG120400-61 - 䖃 䖃 䖃 䖃 䖃 䖃

RNMG 54 TN61 RNMG150600-61 - 䖃 䖃

RNMG 64 TN61 RNMG190600-61 - 䖃 䖃 䖃

RNMG 86 TN61 RNMG250900-61 - 䖃 䖃

- RNGA 43 RNGA120400 - 䖃
medium cutting
Finishing to

P Steel
M Stainless
K Cast iron CL
Round, N Non-ferrous
without hole S Superalloys C C
H Hard materials C
Ceramics
Application

Corner
radius

Chipbreaker Designation
M101S
FX105

TW43
LX11

R Inch Metric
- RNGN 43 RNGN120400 - 䖃 䖃 䖃
medium cutting
Finishing to

RNGN 45 RNGN120700 - 䖃 䖃 䖃

RNGN 43 T0420 - 䖃

RNGN 43 T6 - 䖃

䖃㻌: Line up

Reference pages
RNMG..., RNGA... : External toolholders → B217 -

B072 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL LH CL CL CL C

Insert
M Stainless
K Cast iron CL CL CL CL C
Square, 90° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
T9125
T9115

X407
Inch Metric
TF SNMG 431 TF SNMG120404-TF 0.016" 䖃

SNMG 432 TF SNMG120408-TF 0.031" 䖃

01 SNGG 320.5-01 SNGG090302-01 0.008" 䖃 䖃

SNGG 321-01 SNGG090304-01 0.016" 䖃

SNGG 322-01 SNGG090308-01 0.031" 䖃 䖃

SNGG 430.5-01 SNGG120402-01 0.008" 䖃

Precision finishing

SNGG 431-01 SNGG120404-01 0.016" 䖃

SNGG 432-01 SNGG120408-01 0.031" 䖃 䖃

B~D SNGG 321 R-B SNGG090304R-B 0.016" 䖃 䖃 䖃

SNGG 321 L-B SNGG090304L-B 0.016" 䖃 䖃 䖃

SNGG 322 R-B SNGG090308R-B 0.031" 䖃 䖃

SNGG 322 L-B SNGG090308L-B 0.031" 䖃 䖃

SNGG 431 R-C SNGG120404R-C 0.016" 䖃 䖃

SNGG 431 L-C SNGG120404L-C 0.016" 䖃 䖃 䖃

SNGG 432 R-C SNGG120408R-C 0.031" 䖃

SNGG 432 L-C SNGG120408L-C 0.031" 䖃 䖃

SNGG 432 R-D SNGG120408R-D 0.031" 䖃

SNGG 432 L-D SNGG120408L-D 0.031" 䖃

TSF SNMG 431 TSF SNMG120404-TSF 0.016" 䖃 䖃 䖃 䖃

S
0.031" 䖃 䖃 䖃 䖃
Finishing

SNMG 432 TSF SNMG120408-TSF

SNMG 433 TSF SNMG120412-TSF 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

Tungaloy B073
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel L H LH CL C
M Stainless C L L C L C
K Cast iron C L CL C
Square, 90° N Non-ferrous C
with hole S Superalloys C L
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius
Negative

AH8005

NS9530
AH8015
Chipbreaker Designation

AH630
T6130
T6120

T5105
T5115

TH10
Inch Metric
11 SNMG 431 TN11 SNMG120404-11 0.016" 䖃

䖃 䖃
Finishing

SNMG 432 TN11 SNMG120408-11 0.031"

17 SNMG 432 TN17 SNMG120408-17 0.031" 䖃

Finishing of mild
steels

SF SNMG 431 SF SNMG120404-SF 0.016" 䖃 䖃 䖃

SNMG 432 SF SNMG120408-SF 0.031" 䖃 䖃 䖃

CF SNMG 432 CF SNMG120408-CF 0.031" 䖃 䖃

Finishing

SNMG 433 CF SNMG120412-CF 0.047" 䖃 䖃

HRF SNMG 432 HRF SNMG120408-HRF 0.031" 䖃 䖃

SNMG 433 HRF SNMG120412-HRF 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

B074 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H L H LH H CL CL CL CL

Insert
M Stainless C L L H CL CL
K Cast iron CL CL CL CL CL CL
Square, 90° N Non-ferrous
with hole S Superalloys CL
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

GH330
AH630
AH645
AH120
T9105

T9135
T9125

T6130
T6120
T9115
Inch Metric
TS SNMG 431 TS SNMG120404-TS 0.016" 䖃 䖃 䖃 䖃

0.031" 䖃 䖃 䖃 䖃 䖃 䖃
Finishing

SNMG 432 TS SNMG120408-TS

SNMG 433 TS SNMG120412-TS 0.047" 䖃 䖃 䖃

AS SNMG 431 AS SNMG120404-AS 0.016" 䖃

small depth of cut

SNMG 432 AS SNMG120408-AS 0.031" 䖃 䖃 䖃

High feed,

NS SNMG 432 NS SNMG120408-NS 0.031" 䖃 䖃

Finishing

SS SNMG 431 SS SNMG120404-SS 0.016" 䖃 䖃 䖃 䖃 䖃

SNMG 432 SS SNMG120408-SS 0.031" 䖃 䖃 䖃 䖃 䖃

SNMG 433 SS SNMG120412-SS 0.047" 䖃 䖃 䖃 䖃

TM SNMG 321 TM SNMG090304-TM 0.016" 䖃 䖃 䖃

SNMG 322 TM SNMG090308-TM 0.031" 䖃 䖃 䖃

SNMG 431 TM SNMG120404-TM 0.016" 䖃 䖃 䖃

SNMG 432 TM SNMG120408-TM 0.031" 䖃 䖃 䖃 䖃 䖃

S
Medium cutting

SNMG 433 TM SNMG120412-TM 0.047" 䖃 䖃 䖃 䖃 䖃

SNMG 434 TM SNMG120416-TM 0.063" 䖃 䖃 䖃

SNMG 542 TM SNMG150608-TM 0.031" 䖃

SNMG 543 TM SNMG150612-TM 0.047" 䖃 䖃

SNMG 642 TM SNMG190608-TM 0.031" 䖃 䖃

SNMG 643 TM SNMG190612-TM 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

Tungaloy B075
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H H C CL CL CL CL C
M Stainless L C CL C
K Cast iron CL CL CL C L H C CL CL CL CL C
Square, 90° N Non-ferrous C
with hole S Superalloys C CL L
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
Chipbreaker Designation

NS520
AH120
AH905
GT720
AH110
T9105

T9135
T9125

T6130

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
Finishing to medium

ZM SNMG 432 ZM SNMG120408-ZM 0.031" 䖃 䖃 䖃

SNMG 433 ZM SNMG120412-ZM 0.047" 䖃 䖃 䖃

cutting

DM SNMG 432 DM SNMG120408-DM 0.031" 䖃 䖃

SNMG 433 DM SNMG120412-DM 0.047" 䖃 䖃 䖃

All-round SNMG 321 SNMG090304 0.016" 䖃 䖃 䖃 䖃

SNMG 322 SNMG090308 0.031" 䖃 䖃 䖃 䖃 䖃

Medium cutting

SNMG 431 SNMG120404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 432 SNMG120408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 433 SNMG120412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 434 SNMG120416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 435 SNMG120420 0.078" 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 543 SNMG150612 0.047" 䖃 䖃 䖃 䖃 䖃

SNMG 544 SNMG150616 0.063" 䖃 䖃 䖃

SNMG 643 SNMG190612 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 644 SNMG190616 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 856 SNMG250724 0.094" 䖃 䖃 䖃

SNMG 866 SNMG250924 0.094" 䖃 䖃 䖃 䖃 䖃

S
Finishing to medium

27 SNMG 432 TN27 SNMG120408-27 0.031" 䖃 䖃

SNMG 433 TN27 SNMG120412-27 0.047" 䖃

cutting

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

B076 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL LH H L H LH H L C CL CL C

Insert
M Stainless C L L H L C L C CL C
K Cast iron CL C L H L C CL CL C
Square, 90° N Non-ferrous C
with hole S Superalloys C C L C
H Hard materials
Coated Un-
Cermet coated
Application

Corner
radius

Negative
AH8005

NS9530
AH8015
Chipbreaker Designation

GH330
AH630
AH645

AH725

GH110
T9135
T9125

T6130
T6120

T5105

T5125
T9115

T5115

TH10
Inch Metric
37 SNMG 432 TN37 SNMG120408-37 0.031" 䖃 䖃 䖃 䖃

SM SNMG 432 SM SNMG120408-SM 0.031" 䖃 䖃 䖃 䖃 䖃

SNMG 433 SM SNMG120412-SM 0.047" 䖃 䖃 䖃 䖃

SNMG 866 SM SNMG250924-SM 0.094" 䖃 䖃 䖃 䖃

Medium cutting

CM SNMG 432 CM SNMG120408-CM 0.031" 䖃 䖃 䖃

SNMG 433 CM SNMG120412-CM 0.047" 䖃 䖃 䖃

P SNGG 321 FRP SNGG090304R-P 0.016" 䖃 䖃

SNGG 321 FLP SNGG090304L-P 0.016" 䖃 䖃

SNGG 322 FRP SNGG090308R-P 0.031" 䖃 䖃 䖃

SNGG 322 FLP SNGG090308L-P 0.031" 䖃

SNGG 431 FRP SNGG120404R-P 0.016" 䖃 䖃

SNGG 431 FLP SNGG120404L-P 0.016" 䖃 䖃

SNGG 432 FRP SNGG120408R-P 0.031" 䖃 䖃

SNGG 432 FLP SNGG120408L-P 0.031" 䖃 䖃

S
HRM SNMG 432 HRM SNMG120408-HRM 0.031" 䖃 䖃
Finishing to medium

SNMG 433 HRM SNMG120412-HRM 0.047" 䖃 䖃

SNMG 542 HRM SNMG150608-HRM 0.031" 䖃 䖃

cutting

SNMG 543 HRM SNMG150612-HRM 0.047" 䖃 䖃

SNMG 643 HRM SNMG190612-HRM 0.047" 䖃 䖃

SNMG 644 HRM SNMG190616-HRM 0.063" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

Tungaloy B077
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H L H LH H CL CL CL
M Stainless C L L H CL CL
K Cast iron CL CL CL CL CL LH
Square, 90° N Non-ferrous LH
with hole S Superalloys CL L LH
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius
Negative

NS9530
Chipbreaker Designation

GH330
AH905
AH630
AH645
AH120
T9105

T9135
T9125

T6130
T6120
T9115

KS20
Inch Metric
HMM SNMG 432 HMM SNMG120408-HMM 0.031" 䖃

SNMG 433 HMM SNMG120412-HMM 0.047" 䖃

SA SNMG 431 SA SNMG120404-SA 0.016" 䖃 䖃 䖃 䖃 䖃

Medium cutting

SNMG 432 SA SNMG120408-SA 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 433 SA SNMG120412-SA 0.047" 䖃 䖃 䖃 䖃 䖃

SNMG 643 SA SNMG190612-SA 0.047" 䖃 䖃

SNMG 644 SA SNMG190616-SA 0.063" 䖃

S SNMG 431 R-S SNMG120404R-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 431 L-S SNMG120404L-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 432 R-S SNMG120408R-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMG 432 L-S SNMG120408L-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TH SNMG 432 TH SNMG120408-TH 0.031" 䖃 䖃 䖃 䖃 䖃

SNMG 433 TH SNMG120412-TH 0.047" 䖃 䖃 䖃 䖃

SNMG 543 TH SNMG150612-TH 0.047" 䖃 䖃 䖃 䖃

SNMG 544 TH SNMG150616-TH 0.063" 䖃 䖃 䖃 䖃

SNMG 643 TH SNMG190612-TH 0.047" 䖃 䖃 䖃 䖃 䖃

SNMG 644 TH SNMG190616-TH 0.063" 䖃 䖃 䖃 䖃 䖃

Medium to heavy cutting

S THS SNMG 432 THS SNMG120408-THS 0.031" 䖃 䖃 䖃

SNMG 433 THS SNMG120412-THS 0.047" 䖃 䖃 䖃

SNMG 543 THS SNMG150612-THS 0.047" 䖃 䖃

SNMG 544 THS SNMG150616-THS 0.063" 䖃 䖃

SNMG 642 THS SNMG190608-THS 0.031" 䖃 䖃 䖃

SNMG 643 THS SNMG190612-THS 0.047" 䖃 䖃 䖃

SNMG 644 THS SNMG190616-THS 0.063" 䖃 䖃 䖃

SNMG 646 THS SNMG190624-THS 0.094" 䖃 䖃 䖃

SNMG 854 THS SNMG250716-THS 0.063" 䖃 䖃 䖃

SNMG 856 THS SNMG250724-THS 0.094" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

B078 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL LH H H LH H

Insert
M Stainless L L H
K Cast iron CL C L H
Square, 90° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated
Application

Corner
radius

Negative
Chipbreaker Designation

AH630
AH645
T9135
T9125

T6130

T5105

T5125
T9115

T5115
Inch Metric
cutting (Single sided)

TRS SNMM 543 TRS SNMM150612-TRS 0.047" 䖃 䖃 䖃

Medium to heavy

SNMM 544 TRS SNMM150616-TRS 0.063" 䖃 䖃 䖃

SNMM 644 TRS SNMM190616-TRS 0.063" 䖃 䖃 䖃
SNMM 646 TRS SNMM190624-TRS 0.094" 䖃 䖃 䖃
SNMM 866 TRS SNMM250924-TRS 0.094" 䖃 䖃 䖃

TU SNMM 644 TU SNMM190616-TU 0.063" 䖃

SNMM 646 TU SNMM190624-TU 0.094" 䖃 䖃

SNMM 856 TU SNMM250724-TU 0.094" 䖃 䖃

Heavy cutting (Single sided)

SNMM 866 TU SNMM250924-TU 0.094" 䖃 䖃

TUS SNMM 643 TUS SNMM190612-TUS 0.047" 䖃 䖃 䖃

SNMM 644 TUS SNMM190616-TUS 0.063" 䖃 䖃 䖃

SNMM 646 TUS SNMM190624-TUS 0.094" 䖃 䖃 䖃
SNMM 856 TUS SNMM250724-TUS 0.094" 䖃 䖃 䖃
SNMM 858 TUS SNMM250732-TUS 0.125" 䖃 䖃
SNMM 866 TUS SNMM250924-TUS 0.094" 䖃 䖃 䖃
SNMM 868 TUS SNMM250932-TUS 0.125" 䖃 䖃

SH SNMG 432 SH SNMG120408-SH 0.031" 䖃 䖃 䖃

SNMG 433 SH SNMG120412-SH 0.047" 䖃 䖃 䖃

SNMG 543 SH SNMG150612-SH 0.047" 䖃 䖃 䖃

Medium to heavy cutting

SNMG 544 SH SNMG150616-SH 0.063" 䖃 䖃 䖃

SNMG 643 SH SNMG190612-SH 0.047" 䖃 䖃 䖃

S
SNMG 644 SH SNMG190616-SH 0.063" 䖃 䖃 䖃

CH SNMG 432 CH SNMG120408-CH 0.031" 䖃 䖃 䖃

SNMG 433 CH SNMG120412-CH 0.047" 䖃 䖃 䖃

SNMG 434 CH SNMG120416-CH 0.063" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

Tungaloy B079
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL CL C
M Stainless C
K Cast iron CL C L H CL CL C CL C
Square, 90° N Non-ferrous C
with hole S Superalloys
H Hard materials C
Coated Coated Cermet Uncoated Ceramics
cermet
Application

Corner
radius
Negative

Chipbreaker Designation

NS520
GT720

FX105
T5105

T5125
T5115

TH10

LX21
LX11
T515
Inch Metric
- SNMA 322 SNMA090308 0.031" 䖃 䖃 䖃 䖃

SNMA 323 SNMA090312 0.047" 䖃 䖃

SNMA 431 SNMA120404 0.016" 䖃 䖃 䖃 䖃

SNMA 432 SNMA120408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

SNMA 433 SNMA120412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SNMA 434 SNMA120416 0.063" 䖃 䖃 䖃

SNMA 543 SNMA150612 0.047" 䖃 䖃 䖃

SNMA 643 SNMA190612 0.047" 䖃 䖃 䖃

- SNGA 321 SNGA090304 0.016" 䖃

SNGA 431 SNGA120404 0.016" 䖃 䖃 䖃

SNGA 432 SNGA120408 0.031" 䖃 䖃 䖃 䖃

SNGA 433 SNGA120412 0.047" 䖃 䖃 䖃 䖃

SNGA 434 SNGA120416 0.063" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B213 -  Internal toolholders → B322 -

B080 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL C

Insert
M Stainless CL C
K Cast iron CL C CL C
Square, 90° N Non-ferrous C
without hole S Superalloys CL
H Hard materials C
Coated Uncoated Ceramics
Application

Corner
radius

Negative
Chipbreaker Designation

AH120

FX105
LX21
TH10

LX11
Inch Metric
- SNGD 453 SNGD120712 0.047" 䖃

SNGD 545 SNGD120716 0.063" 䖃

- SNGN 322 SNGN090308 0.031" 䖃 䖃

SNGN 421 SNGN120304 0.016" 䖃

SNGN 423 SNGN120312 0.047" 䖃

SNGN 431 SNGN120404 0.016" 䖃

SNGN 432 SNGN120408 0.031" 䖃 䖃 䖃 䖃

SNGN 433 SNGN120412 0.047" 䖃 䖃 䖃

SNGN 434 SNGN120416 0.063" 䖃 䖃 䖃

SNGN 435 SNGN120420 0.078" 䖃 䖃

SNGN 436 SNGN120424 0.094" 䖃

Finishing to medium cutting

SNGN 452 SNGN120708 0.031" 䖃

SNGN 453 SNGN120712 0.047" 䖃 䖃

SNGN 454 SNGN120716 0.063" 䖃 䖃

SNGN 455 SNGN120720 0.078" 䖃

- SNMN 432 SNMN120408 0.031" 䖃

SNMN 433 SNMN-120412 0.047" 䖃

*SNMN 434 SNMN120416 0.063" 䖃

S
- **SNMN 432 TN SNMN120408TN 0.031" 䖃

**SNMN 433 TN SNMN120412TN 0.047" 䖃

**SNMN 434 TN SNMN120416TN 0.063" 䖃

**SNMN 435 TN SNMN120420TN 0.078" 䖃

**SNMN 436 TN SNMN120424TN 0.094" 䖃

**SNMN 634 TN SNMN190416TN 0.063" 䖃

- SNGX 545 SNGX120716 䖃

* Chamfer hone 0.008" wide, -25° angle.

** Chamfer hone 0.005" wide, -25° angle.
Note: Carbide grades have a radius hone.
䖃㻌: Line up

Reference pages
SNGD... : External toolholders → B273
SNGN..., SNMN... : External toolholders → B256 -, Internal toolholders → B342 -

Tungaloy B081
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL CL CL CL CL CL C C
M Stainless C CL CL C
K Cast iron C CL CL CL CL CL C C
Triangular, 60° N Non-ferrous C
with hole S Superalloys C
H Hard materials
Coated Coated cermet Cermet Uncoated
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

GH330

NS520
SH725

GT720
GH110

TH10
X407
Inch Metric
TF TNMG 331 TF TNMG160404-TF 0.016" 䖃 䖃 䖃

TNMG 332 TF TNMG160408-TF 0.031" 䖃 䖃

Precision finishing

01 TNGG 220.5-01 TNGG110302-01 0.008" 䖃

TNGG 221-01 TNGG110304-01 0.016" 䖃

TNGG 222-01 TNGG110308-01 0.031" 䖃 䖃

TNGG 330.5-01 TNGG160402-01 0.008" 䖃 䖃 䖃 䖃

TNGG 331-01 TNGG160404-01 0.016" 䖃 䖃 䖃 䖃

TNGG 332-01 TNGG160408-01 0.031" 䖃 䖃 䖃

TNGG 333-01 TNGG160412-01 0.047" 䖃 䖃

01 TNGG330.5F-01 TNGG160402F-01 0.008" 䖃

Precision finishing
(Sharp edge)

TNGG331F-01 TNGG160404F-01 0.016" 䖃

TNGG332F-01 TNGG160408F-01 0.031" 䖃

A~C TNGG 221 R-A TNGG110304R-A 0.016" 䖃 䖃

TNGG 221 L-A TNGG110304L-A 0.016" 䖃 䖃

TNGG 222 R-A TNGG110308R-A 0.031" 䖃 䖃

TNGG 222 L-A TNGG110308L-A 0.031" 䖃 䖃

TNGG 321 R-C TNGG160304R-C 0.016" 䖃 䖃

TNGG 321 L-C TNGG160304L-C 0.016" 䖃

Precision finishing

TNGG 322 R-C TNGG160308R-C 0.031" 䖃

T
TNGG 322 L-C TNGG160308L-C 0.031" 䖃

TNGG 33V R-C TNGG160400R-C 0.0012" 䖃

TNGG 33V L-C TNGG160400L-C 0.0012" 䖃

TNGG 330.5 R-C TNGG160402R-C 0.008" 䖃 䖃 䖃 䖃

TNGG 330.5 L-C TNGG160402L-C 0.008" 䖃 䖃

TNGG 331 R-C TNGG160404R-C 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNGG 331 L-C TNGG160404L-C 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TNGG 332 R-C TNGG160408R-C 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNGG 332 L-C TNGG160408L-C 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

B082 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H CL CL CL CL C C

Insert
M Stainless CL CL C
K Cast iron CL CL CL CL CL C
Triangular, 60° N Non-ferrous C
with hole S Superalloys CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

SH725
AH120
T9105

T9135
T9125
T9115

TH10
X407
Inch Metric
D TNGG 431 R-D TNGG220404R-D 0.016" 䖃 䖃

TNGG 431 L-D TNGG220404L-D 0.016" 䖃

TNGG 432 R-D TNGG220408R-D 0.031" 䖃 䖃

Precision finishing

TNGG 432 L-D TNGG220408L-D 0.031" 䖃

W TNGG 331 R-W TNGG160404R-W 0.016" 䖃 䖃

TNGG 331 L-W TNGG160404L-W 0.016" 䖃 䖃

TNGG 332 R-W TNGG160408R-W 0.031" 䖃

TNGG 332 L-W TNGG160408L-W 0.031" 䖃

W TNGG 330.5FR-W TNGG160402FR-W 0.008" 䖃

Precision finishing

TNGG 330.5FL-W TNGG160402FL-W 0.008" 䖃

(Sharp edge)

TNGG 331FR-W TNGG160404FR-W 0.016" 䖃

TNGG 331FL-W TNGG160404FL-W 0.016" 䖃

TNGG332FR-W TNGG160408FR-W 0.031" 䖃

TNGG 332FL-W TNGG160408FL-W 0.031" 䖃

TSF TNMG 231E-TSF TNMG110404E-TSF 0.016" 䖃 䖃 䖃 䖃

TNMG 232E-TSF TNMG110408E-TSF 0.031" 䖃 䖃 䖃 䖃

TNMG 330.5 TSF TNMG160402-TSF 䖃 䖃 䖃

Finishing

0.008"

TNMG 331 TSF TNMG160404-TSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 332 TSF TNMG160408-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 333 TSF TNMG160412-TSF 0.047" 䖃 䖃 䖃 䖃

Finishing (Wiper)

FW TNMG 231E-FW TNMG110404E-FW 0.016" 䖃

T
TNMG 232E-FW TNMG110408E-FW 0.031" 䖃

TNMG 332-FW TNMG160404-FW 0.016" 䖃

TNMG 333-FW TNMG160408-FW 0.031" 䖃

ZF TNMG 331 ZF TNMG160404-ZF 0.016" 䖃 䖃 䖃 䖃 䖃

䖃 䖃 䖃 䖃 䖃
Finishing

TNMG 332 ZF TNMG160408-ZF 0.031"

TNMG 333 ZF TNMG160412-ZF 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B206 - Internal toolholders → B296 -
J series toolholders → B377 -

Tungaloy B083
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel LH L H LH CL CL C
M Stainless C L L C L CL C
K Cast iron C L CL CL C
Triangular, 60° N Non-ferrous C
with hole S Superalloys C L
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius
Negative

AH8005

NS9530
AH8015
Chipbreaker Designation

GH330
AH630
T9125

T6130
T6120

T5105
T5115

TH10
Inch Metric
11 TNMG 221 TN11 TNMG110304-11 0.016" 䖃

TNMG 222 TN11 TNMG110308-11 0.031" 䖃

TNMG 330.5 TN11 TNMG160402-11 0.008" 䖃

Finishing

TNMG 331 TN11 TNMG160404-11 0.016" 䖃 䖃 䖃

TNMG 332 TN11 TNMG160408-11 0.031" 䖃

TNMG 431 TN11 TNMG220404-11 0.016" 䖃

TNMG 432 TN11 TNMG220408-11 0.031" 䖃

17 TNMG 331 TN17 TNMG160404-17 0.016" 䖃 䖃 䖃

Finishing of mild

TNMG 332 TN17 TNMG160408-17 0.031" 䖃 䖃

steels

SF TNMG 331 SF TNMG160404-SF 0.016" 䖃 䖃 䖃

TNMG 332 SF TNMG160408-SF 0.031" 䖃 䖃 䖃

TNMG 333 SF TNMG160412-SF 0.047" 䖃 䖃 䖃

CF TNMG 331 CF TNMG160404-CF 0.016" 䖃 䖃

䖃 䖃
Finishing

TNMG 332 CF TNMG160408-CF 0.031"

HRF TNMG 331 HRF TNMG160404-HRF 0.016" 䖃 䖃

TNMG 332 HRF TNMG160408-HRF 0.031" 䖃 䖃

T

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

B084 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H CL CL CL

Insert
M Stainless
K Cast iron CL CL CL CL CL
Triangular, 60° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
T9105

T9135
T9125
T9115
Inch Metric
TS TNMG 331 TS TNMG160404-TS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing

TNMG 332 TS TNMG160408-TS

TNMG 333 TS TNMG160412-TS 0.047" 䖃 䖃 䖃 䖃
Finishing to medium

SW TNMG 232E-SW TNMG110408E-SW 0.031" 䖃

cutting (Wiper)

TNMG 233E-SW TNMG110412E-SW 0.047" 䖃

TNMG 332-SW TNMG160408-SW 0.031" 䖃

TNMG 333-SW TNMG160412-SW 0.047" 䖃

AS TNMG 331 AS TNMG160404-AS 0.016" 䖃 䖃 䖃

small depth of cut

TNMG 332 AS TNMG160408-AS 0.031" 䖃 䖃 䖃 䖃 䖃

High feed,

TNMG 333 AS TNMG160412-AS 0.047" 䖃 䖃 䖃

CB TNMG 221 CB TNMG110304-CB 0.016" 䖃 䖃

(Double sided)

TNMG 222 CB TNMG110308-CB 0.031" 䖃 䖃

Boring

NS TNMG 331 NS TNMG160404-NS 0.016" 䖃 䖃 䖃

Finishing

TNMG 332 NS TNMG160408-NS 0.031" 䖃 䖃 䖃 䖃

T
䖃㻌: Line up

Reference pages
External toolholders → B206 - Internal toolholders → B296 -
J series toolholders → B377 -

Tungaloy B085
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H L H LH H C CL L CL CL CL
M Stainless C L L H C CL L CL
K Cast iron CL CL C CL L CL CL CL LH
Triangular, 60° N Non-ferrous LH
with hole S Superalloys C CL C LH
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

GH330
AH630
AH645

AH725
AH120
AH110
T9105

T9135
T9125

T6130
T6120
T9115

KS20
Inch Metric
SS TNMG 231E SS TNMG110404E-SS 0.016" 䖃 䖃

TNMG 232E SS TNMG110408E-SS 0.031" 䖃 䖃

TNMG 331 SS TNMG160404-SS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

䖃 䖃 䖃 䖃 䖃 䖃
Finishing

TNMG 332 SS TNMG160408-SS 0.031"

TNMG 333 SS TNMG160412-SS 0.047" 䖃 䖃 䖃 䖃 䖃

TNMG 431 SS TNMG220404-SS 0.016" 䖃 䖃 䖃 䖃 䖃

TNMG 432 SS TNMG220408-SS 0.031" 䖃 䖃 䖃 䖃 䖃

TNMG 433 SS TNMG220412-SS 0.047" 䖃 䖃 䖃 䖃

TM TNMG 221 TM TNMG110304-TM 0.016" 䖃 䖃 䖃

TNMG 222 TM TNMG110308-TM 0.031" 䖃 䖃 䖃

TNMG 231E TM TNMG110404E-TM 0.016" 䖃 䖃

TNMG 232E TM TNMG110408E-TM 0.031" 䖃 䖃

TNMG 233E TM TNMG110412E-TM 0.047" 䖃 䖃

Medium cutting

TNMG 321 TM TNMG160304-TM 0.016" 䖃 䖃 䖃

TNMG 322 TM TNMG160308-TM 0.031" 䖃 䖃

TNMG 331 TM TNMG160404-TM 0.016" 䖃 䖃 䖃 䖃 䖃

TNMG 332 TM TNMG160408-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 333 TM TNMG160412-TM 0.047" 䖃 䖃 䖃 䖃

TNMG 431 TM TNMG220404-TM 0.016" 䖃 䖃 䖃

TNMG 432 TM TNMG220408-TM 0.031" 䖃 䖃 䖃 䖃 䖃

TNMG 433 TM TNMG220412-TM 0.047" 䖃 䖃 䖃 䖃

TNMG 434 TM TNMG220416-TM 0.063" 䖃 䖃

AM TNMG 332 AM TNMG160408-AM 0.031" 䖃 䖃

TNMG 333 AM TNMG160412-AM 0.047" 䖃 䖃

T
Finishing to medium cutting

NM TNMG 332 NM TNMG160408-NM 0.031" 䖃

TNMG 333 NM TNMG160412-NM 0.047" 䖃 䖃

TQ TNMG 331 TQ TNMG160404-TQ 0.016" 䖃 䖃

TNMG 332 TQ TNMG160408-TQ 0.031" 䖃 䖃

Reference pages
䖃㻌: Line up
External toolholders → B206 - Internal toolholders → B296 -
J series toolholders → B377 -

B086 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H LH C CL CL CL CL CL C

Insert
M Stainless L C CL C
K Cast iron CL CL CL C L H C CL CL CL CL CL C
Triangular, 60° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Un-
cermet coated
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

AH630

NS520
AH120

GT720
AH110
T9105

T9135
T9125

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
ZM TNMG 331 ZM TNMG160404-ZM 䖃 䖃 䖃 䖃 䖃
Finishing to medium

0.016"

TNMG 332 ZM TNMG160408-ZM 0.031" 䖃 䖃 䖃 䖃 䖃

cutting

TNMG 333 ZM TNMG160412-ZM 0.047" 䖃 䖃 䖃

TNMG 432 ZM TNMG220408-ZM 0.031" 䖃

TNMG 433 ZM TNMG220412-ZM 0.047" 䖃

DM TNMG 332 DM TNMG160408-DM 0.031" 䖃 䖃 䖃 䖃

TNMG 333 DM TNMG160412-DM 0.047" 䖃 䖃

TNMG 434 DM TNMG220416-DM 0.063" 䖃

All-round TNMG 221 TNMG110304 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 222 TNMG110308 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 321 TNMG160304 0.016" 䖃

䖃
Medium cutting

TNMG 322 TNMG160308 0.031"

TNMG 331 TNMG160404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 332 TNMG160408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 333 TNMG160412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 334 TNMG160416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 335 TNMG160420 0.078" 䖃 䖃 䖃

TNMG 432 TNMG220408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 433 TNMG220412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 434 TNMG220416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 542 TNMG270608 0.031" 䖃 䖃

TNMG 543 TNMG270612 0.047" 䖃 䖃

T
TNMG 544 TNMG270616 0.063" 䖃

27 TNMG 322 TN27 TNMG160308-27 0.031" 䖃

Finishing to medium cutting

TNMG 331 TN27 TNMG160404-27 0.016" 䖃 䖃

TNMG 332 TN27 TNMG160408-27 0.031" 䖃 䖃 䖃

TNMG 333 TN27 TNMG160412-27 0.047" 䖃 䖃

TNMG 431 TN27 TNMG220404-27 0.016" 䖃

TNMG 432 TN27 TNMG220408-27 0.031" 䖃 䖃

TNMG 433 TN27 TNMG220412-27 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

Tungaloy B087
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CLLH H L H LH H C CL L CL CL CL C
M Stainless C L L H C CL L CL C
K Cast iron CL CL C L H C CL L CL CL CL C
Triangular, 60° N Non-ferrous C
with hole S Superalloys C CL C
H Hard materials
Coated Coated Cermet Un-
cermet coated
Application

Corner
radius
Negative

NS9530
Chipbreaker Designation

GH330
AH630
AH645

AH725
AH120

GT720
AH110
T9135
T9125

T6130
T6120

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
28 TNMG 331 TN28 TNMG160404-28 0.016" 䖃 䖃
TNMG 332 TN28 TNMG160408-28 0.031" 䖃 䖃
TNMG 431 TN28 TNMG220404-28 0.016" 䖃 䖃
TNMG 432 TN28 TNMG220408-28 0.031" 䖃 䖃

32 TNMG 666 TN32 TNMG330924-32 0.094" 䖃 䖃

33 TNMG 331 TN33 TNMG160404-33 0.016" 䖃

TNMG 332 TN33 TNMG160408-33 0.031" 䖃
TNMG 334 TN33 TNMG160416-33 0.063" 䖃
TNMG 431 TN33 TNMG220404-33 0.016" 䖃 䖃
TNMG 433 TN33 TNMG220412-33 0.047" 䖃
TNMG 434 TN33 TNMG220416-33 0.063" 䖃

37 TNMG 331 TN37 TNMG160404-37 0.016" 䖃 䖃 䖃

TNMG 332 TN37 TNMG160408-37 0.031" 䖃 䖃 䖃
Medium cutting

38 TNMG 331 TN38 TNMG160404-38 0.016" 䖃

TNMG 332 TN38 TNMG160408-38 0.031" 䖃

SM TNMG 231E-SM TNMG110404E-SM 0.016" 䖃 䖃 䖃

T TNMG 232E-SM TNMG110408E-SM 0.031" 䖃 䖃 䖃
TNMG 331 SM TNMG160404-SM 0.016" 䖃 䖃 䖃 䖃 䖃
TNMG 332 SM TNMG160408-SM 0.031" 䖃 䖃 䖃 䖃 䖃
TNMG 333 SM TNMG160412-SM 0.047" 䖃 䖃 䖃 䖃
TNMG 432 SM TNMG220408-SM 0.031" 䖃 䖃 䖃 䖃
TNMG 433 SM TNMG220412-SM 0.047" 䖃 䖃 䖃 䖃
TNMG 666 SM TNMG330924-SM 0.094" 䖃 䖃

CM TNMG 331 CM TNMG160404-CM 0.016" 䖃 䖃 䖃 䖃

TNMG 332 CM TNMG160408-CM 0.031" 䖃 䖃 䖃 䖃
TNMG 333 CM TNMG160412-CM 0.047" 䖃 䖃 䖃 䖃
TNMG 432 CM TNMG220408-CM 0.031" 䖃 䖃 䖃
TNMG 433 CM TNMG220412-CM 0.047" 䖃 䖃 䖃

Reference pages
䖃㻌: Line up
External toolholders → B206 - Internal toolholders → B296 -
J series toolholders → B377 -

B088 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel L H LH H CL C CL CL CL C

Insert
M Stainless C L L H CL C L C CL CL C
K Cast iron CL C CL CL C LH
Triangular, 60° N Non-ferrous C LH
with hole S Superalloys CL C L L C LH
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

Negative
AH8005

NS9530
AH8015
Chipbreaker Designation

GH330
AH905
AH630
AH645

SH725
AH120

GH110
T6130
T6120

KS20
TH10
Inch Metric
P TNGG 330.5 R-P TNGG160402R-P 0.008" 䖃 䖃 䖃 䖃

TNGG 330.5 L-P TNGG160402L-P 䖃 䖃 䖃 䖃

Medium cutting

0.008"

TNGG 331 R-P TNGG160404R-P 0.016" 䖃 䖃 䖃 䖃

TNGG 331 L-P TNGG160404L-P 0.016" 䖃 䖃 䖃 䖃

TNGG 332 R-P TNGG160408R-P 0.031" 䖃 䖃 䖃 䖃

TNGG 332 L-P TNGG160408L-P 0.031" 䖃 䖃 䖃 䖃

P TNGG 330.5FR-P TNGG160402FR-P 0.008" 䖃

TNGG 330.5FL-P TNGG160402FL-P 0.008" 䖃

Medium cutting
(Sharp edge)

TNGG 331FR-P TNGG160404FR-P 0.016" 䖃

TNGG 331FL-P TNGG160404FL-P 0.016" 䖃

TNGG 332FR-P TNGG160408FR-P 0.031" 䖃

TNGG 332FL-P TNGG160408FL-P 0.031" 䖃

HRM TNMG 331 HRM TNMG160404-HRM 0.016" 䖃 䖃

medium cutting
Finishing to

TNMG 332 HRM TNMG160408-HRM 0.031" 䖃 䖃

TNMG 333 HRM TNMG160412-HRM 0.047" 䖃 䖃

HMM TNMG 331 HMM TNMG160404-HMM 0.016" 䖃

TNMG 332 HMM TNMG160408-HMM 0.031" 䖃

TNMG 333 HMM TNMG160412-HMM 0.047" 䖃

Medium cutting

SA TNMG 331 SA TNMG160404-SA 0.016" 䖃 䖃 䖃 䖃 䖃

䖃
T
TNMG 332 SA TNMG160408-SA 0.031" 䖃 䖃 䖃 䖃 䖃

TNMG 333 SA TNMG160412-SA 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 432 SA TNMG220408-SA 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 433 SA TNMG220412-SA 0.047" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

Tungaloy B089
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H H LH H CL L CL CL
M Stainless L L H CL L CL
K Cast iron CL CL CL C L H CL L CL CL
Triangular, 60° N Non-ferrous
with hole S Superalloys CL C
H Hard materials
Coated Cermet
Application

Corner
radius
Negative

NS9530
Chipbreaker Designation

GH330
AH630
AH645

AH120
AH725
T9105

T9135
T9125

T6130

T5105

T5125
T9115

T5115
T515
Inch Metric
S TNMG 331 R-S TNMG160404R-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 331 L-S TNMG160404L-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 332 R-S TNMG160408R-S 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

0.031"

TNMG 332 L-S TNMG160408L-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 431 R-S TNMG220404R-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 431 L-S TNMG220404L-S 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 432 R-S TNMG220408R-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMG 432 L-S TNMG220408L-S 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TH TNMG 432 TH TNMG220408-TH 0.031" 䖃 䖃 䖃 䖃 䖃

TNMG 433 TH TNMG220412-TH 0.047" 䖃 䖃 䖃 䖃

Medium to heavy cutting

THS TNMG 432 THS TNMG220408-THS 0.031" 䖃 䖃 䖃

TNMG 433 THS TNMG220412-THS 0.047" 䖃 䖃 䖃

CH TNMG 331 CH TNMG160404-CH 0.016" 䖃 䖃 䖃 䖃

TNMG 332 CH TNMG160408-CH 0.031" 䖃 䖃 䖃 䖃

TNMG 333 CH TNMG160412-CH 0.047" 䖃 䖃 䖃 䖃

TNMG 432 CH TNMG220408-CH 0.031" 䖃 䖃 䖃

TNMG 433 CH TNMG220412-CH 0.047" 䖃 䖃 䖃

TNMG 434 CH TNMG220416-CH 0.063" 䖃 䖃 䖃

T

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

B090 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL CL C C

Insert
M Stainless C C C
K Cast iron CL C L H C CL CL C C CL C
Triangular, 60° N Non-ferrous C C
with hole S Superalloys C
H Hard materials C
Coated Coated Cermet Uncoated Ceramics
cermet
Application

Corner
radius

Negative
Chipbreaker Designation

NS520
GT720
GH110

FX105
T5105

T5125
T5115

TH03

LX21
TH10

LX11
T515
Inch Metric
- TNMA 331 TNMA160404 0.016" 䖃 䖃 䖃 䖃 䖃

TNMA 332 TNMA160408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNMA 333 TNMA160412 0.047" 䖃 䖃 䖃 䖃 䖃

TNMA 334 TNMA160416 0.063" 䖃 䖃 䖃

TNMA 335 TNMA160420 0.078" 䖃 䖃 䖃

TNMA 431 TNMA220404 0.016" 䖃 䖃 䖃

TNMA 432 TNMA220408 0.031" 䖃 䖃 䖃

Finishing to medium cutting

TNMA 433 TNMA220412 0.047" 䖃 䖃 䖃

TNMA 434 TNMA220416 0.063" 䖃 䖃 䖃

- TNGA 221 TNGA110304 0.016" 䖃

TNGA 222 TNGA110308 0.031" 䖃

TNGA 321 TNGA160304 0.016" 䖃

TNGA 322 TNGA160308 0.031" 䖃

TNGA 3305 TNGA160402 0.008" 䖃

TNGA 331 TNGA160404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TNGA 332 TNGA160408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TNGA 333 TNGA160412 0.047" 䖃 䖃 䖃 䖃 䖃

TNGA 334 TNGA160416 0.063" 䖃 䖃 䖃

TNGA 432 TNGA220408 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B323 -
J series toolholders → B377 -

Tungaloy B091
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C
M Stainless C
K Cast iron C CL C
Triangular, 60° N Non-ferrous C
without hole S Superalloys
H Hard materials C
Uncoated Ceramics
Application

Corner
radius
Negative

Chipbreaker Designation

FX105
TH10

LX21
LX11
Inch Metric
䖃 䖃
Finishing to medium cutting

- TNGN 331 TNGN160404 0.016"

TNGN 332 TNGN160408 0.031" 䖃 䖃 䖃

TNGN 333 TNGN160412 0.047" 䖃 䖃 䖃 䖃

TNGN 334 TNGN160416 0.063" 䖃 䖃

TNGN 335 TNGN160420 0.078" 䖃

TNGN 352 TNGN160708 0.031" 䖃

䖃㻌: Line up

Reference pages
TNGN...: External toolholders → B248 -, B256, B258,
Internal toolholders → B342

B092 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H L H LH CL C CL CL CL CL CL C

Insert
M Stainless C L L CL C CL C
K Cast iron CL CL CL C CL CL CL CL CL C
Rhombic, 35° N Non-ferrous C
with hole S Superalloys CL C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

GH330
AH630

NS520
AH120

GT720
GH110
T9105

T9135
T9125

T6130
T6120
T9115

TH10
Inch Metric
TF VNMG 331 TF VNMG160404-TF 0.016" 䖃

VNMG 332 TF VNMG160408-TF 0.031" 䖃 䖃

Precision finishing

01 VNGG 330.5-01 VNGG160402-01 0.008" 䖃 䖃 䖃 䖃

VNGG 331-01 VNGG160404-01 0.016" 䖃 䖃 䖃

VNGG 332-01 VNGG160408-01 0.031" 䖃 䖃

P VNGG 331 FRP VNGG160404R-P 0.016" 䖃

medium cutting
Finishing to

VNGG 332 FRP VNGG160408R-P 0.031" 䖃

TSF VNMG 2.330.5E-TSF VNMG120402E-TSF 0.008" 䖃 䖃 䖃 䖃

VNMG 2.331E-TSF VNMG120404E-TSF 0.016" 䖃 䖃 䖃 䖃

VNMG 2.332E-TSF VNMG120408E-TSF 0.031" 䖃 䖃 䖃 䖃

VNMG 330.5 TSF VNMG160402-TSF 0.008" 䖃 䖃 䖃

VNMG 331 TSF VNMG160404-TSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 332 TSF VNMG160408-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 333 TSF VNMG160412-TSF 0.047" 䖃 䖃 䖃 䖃

ZF VNMG 331 ZF VNMG160404-ZF 0.016" 䖃 䖃 䖃 䖃 䖃

VNMG 332 ZF VNMG160408-ZF 0.031" 䖃 䖃 䖃 䖃 䖃

VNMG 333 ZF VNMG160412-ZF 0.047" 䖃 䖃 䖃

Finishing

11 VNMG 331 TN11 VNMG160404-11 0.016" 䖃 䖃 䖃 V

VNMG 332 TN11 VNMG160408-11 0.031" 䖃

VNMG 333 TN11 VNMG160412-11 0.047" 䖃 䖃

SF VNMG 331 SF VNMG160404-SF 0.016" 䖃 䖃 䖃

VNMG 332 SF VNMG160408-SF 0.031" 䖃 䖃 䖃

Reference pages
䖃㻌: Line up
External toolholders → B207 - Internal toolholders → B298, B325, B328
TungCap → B224

Tungaloy B093
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H L H LH H C CL CL CL CL CL
M Stainless C L L H C CL C L CL
K Cast iron CL CL C L C CL CL CL CL CL
Rhombic, 35° N Non-ferrous
with hole S Superalloys C CL C L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius
Negative

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

GH330
AH630
AH645

NS520
AH120
AH110
T9105

T9135
T9125

T6130
T6120

T5105
T9115

T5115
Inch Metric
CF VNMG 331 CF VNMG160404-CF 0.016" 䖃 䖃

VNMG 332 CF VNMG160408-CF 0.031" 䖃 䖃

HRF VNMG 331 HRF VNMG160404-HRF 0.016" 䖃 䖃

VNMG 332 HRF VNMG160408-HRF 0.031" 䖃 䖃

Finishing

TS VNMG 331 TS VNMG160404-TS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 332 TS VNMG160408-TS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 333 TS VNMG160412-TS 0.047" 䖃 䖃 䖃

SS VNMG 2.331E-SS VNMG120404E-SS 0.016" 䖃 䖃 䖃 䖃

VNMG 2.332E-SS VNMG120408E-SS 0.031" 䖃 䖃 䖃 䖃

VNMG 331 SS VNMG160404-SS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 332 SS VNMG160408-SS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 333 SS VNMG160412-SS 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

TM VNMG 2.331E-TM VNMG120404E-TM 0.016" 䖃 䖃

VNMG 2.332E-TM VNMG120408E-TM 0.031" 䖃 䖃

Medium cutting

VNMG 331 TM VNMG160404-TM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 332 TM VNMG160408-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 333 TM VNMG160412-TM 0.047" 䖃 䖃 䖃 䖃 䖃

V

䖃㻌: Line up

Reference pages
External toolholders → B207 - Internal toolholders → B298, B325, B328
TungCap → B224

B094 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H C CL CL CL C

Insert
M Stainless C CL C
K Cast iron CL CL CL C L H C CL CL CL C
Rhombic, 35° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

AH120
AH110
T9105

T9135
T9125

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
TQ VNMG 331 TQ VNMG160404-TQ 0.016" 䖃 䖃
Finishing to medium cutting

VNMG 332 TQ VNMG160408-TQ 0.031" 䖃 䖃

ZM VNMG 332 ZM VNMG160408-ZM 0.031" 䖃 䖃 䖃

VNMG 333 ZM VNMG160412-ZM 0.047" 䖃 䖃 䖃

DM VNMG 332 DM VNMG160408-DM 0.031" 䖃 䖃 䖃 䖃

VNMG 333 DM VNMG160412-DM 0.047" 䖃 䖃 䖃

All-round VNMG 331 VNMG160404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 332 VNMG160408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VNMG 333 VNMG160412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

28 VNMG 331 TN28 VNMG160404-28 0.016" 䖃

VNMG 332 TN28 VNMG160408-28 0.031" 䖃

33 VNMG 331 TN33 VNMG160404-33 0.016" 䖃 䖃 䖃

VNMG 332 TN33 VNMG160408-33 0.031" 䖃 䖃 䖃

V

䖃㻌: Line up

Reference pages
External toolholders → B211 - Internal toolholders → B325, B328
TungCap → B224

Tungaloy B095
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel L H LH H CL C
M Stainless C L L H C L C
K Cast iron C L H CL C
Rhombic, 35° N Non-ferrous C
with hole S Superalloys C L L
H Hard materials C
Coated Cermet Uncoated Ceramics
Application

Corner
radius
Negative

AH8005
AH8015
Chipbreaker Designation

AH905
AH630
AH645

NS520
T6130
T6120

T5105

T5125
T5115

TH10

LX11
Inch Metric
SM VNMG 2.331E-SM VNMG120404E-SM 0.016" 䖃 䖃 䖃 䖃
VNMG 2.332E-SM VNMG120408E-SM 0.031" 䖃 䖃 䖃 䖃
Medium cutting

VNMG 331 SM VNMG160404-SM 0.016" 䖃 䖃 䖃 䖃

VNMG 332 SM VNMG160408-SM 0.031" 䖃 䖃 䖃 䖃
VNMG 333 SM VNMG160412-SM 0.047" 䖃 䖃 䖃 䖃
CM VNMG 332 CM VNMG160408-CM 0.031" 䖃 䖃 䖃
VNMG 333 CM VNMG160412-CM 0.047" 䖃 䖃 䖃

HRM VNMG 331 HRM VNMG160404-HRM 0.016" 䖃 䖃

medium cutting Medium cutting medium cutting
Finishing to

VNMG 332 HRM VNMG160408-HRM 0.031" 䖃 䖃

VNMG 333 HRM VNMG160412-HRM 0.047" 䖃 䖃

HMM VNMG 331 HMM VNMG160404-HMM 0.016" 䖃

VNMG 332 HMM VNMG160408-HMM 0.031" 䖃
VNMG 333 HMM VNMG160412-HMM 0.047" 䖃

- VNMA 330.5 VNMA160402 0.008" 䖃

Finishing to

VNMA 331 VNMA160404 0.016" 䖃 䖃 䖃 䖃 䖃

VNMA 332 VNMA160408 0.031" 䖃 䖃 䖃 䖃 䖃
VNGA 331 VNGA160404 0.016" 䖃
VNGA 332 VNGA160408 0.031" 䖃

P Steel
M Stainless
K Cast iron CL
Rhombic, 35° N Non-ferrous
without hole S Superalloys
V H Hard materials
Ceramics
Application

Corner
radius

Chipbreaker Designation
FX105

Inch Metric
medium cutting

- VNGD 353 VNGD160712 0.047" 䖃

Finishing to

Reference pages 䖃㻌: Line up

External toolholders → B207 - Internal toolholders → B298, B325, B328

TungCap → B224
VNGD...: External toolholders → B272

B096 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H CL CL CL CL CL

Insert
M Stainless CL
K Cast iron CL CL L CL CL CL CL CL
Trigon, 80° N Non-ferrous
with hole S Superalloys CL
H Hard materials
Coated Coated cermet Cermet
Application

Corner
radius

Negative
NS9530
GT9530
Chipbreaker Designation

NS520
AH120

GT720
T9105

T9135
T9125
T9115

T5115
Inch Metric
TF WNMG 431 TF WNMG080404-TF 0.016" 䖃

WNMG 432 TF WNMG080408-TF 0.031" 䖃

Precision finishing

01 WNGG 430.5-01 WNGG080402-01 0.008" 䖃 䖃

WNGG 431-01 WNGG080404-01 0.016" 䖃 䖃 䖃

WNGG 432-01 WNGG080408-01 0.031" 䖃 䖃

TSF WNMG 331E-TSF WNMG060404E-TSF 0.016" 䖃 䖃 䖃 䖃

WNMG 332E-TSF WNMG060408E-TSF 0.031" 䖃 䖃 䖃 䖃

WNMG 333E-TSF WNMG060412E-TSF 0.047" 䖃 䖃 䖃 䖃

Finishing

WNMG 331 TSF WNMG060404-TSF 0.016" 䖃 䖃

WNMG 332 TSF WNMG060408-TSF 0.031" 䖃 䖃 䖃

WNMG 431 TSF WNMG080404-TSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 432 TSF WNMG080408-TSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 TSF WNMG080412-TSF 0.047" 䖃 䖃 䖃 䖃 䖃

FW WNMG 331E-FW WNMG060404E-FW 0.016" 䖃 䖃 䖃 䖃 䖃

WNMG 332E-FW WNMG060408E-FW 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 431 FW WNMG080404-FW 0.016" 䖃 䖃 䖃 䖃

Finishing (Wiper)

WNMG 432 FW WNMG080408-FW 0.031" 䖃 䖃 䖃 䖃 䖃

AFW WNMG 331 AFW WNMG060404-AFW 0.016" 䖃 䖃 䖃

WNMG 332 AFW WNMG060408-AFW 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 431 AFW WNMG080404-AFW 0.016" 䖃 䖃 䖃

WNMG 432 AFW WNMG080408-AFW 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

W
ZF WNMG 331E-ZF WNMG060404E-ZF 0.016" 䖃 䖃

WNMG 331 ZF WNMG060404-ZF 0.016" 䖃 䖃

Finishing

WNMG 332 ZF WNMG060408-ZF 0.031" 䖃 䖃

WNMG 431 ZF WNMG080404-ZF 0.016" 䖃 䖃 䖃 䖃 䖃

WNMG 432 ZF WNMG080408-ZF 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 433 ZF WNMG080412-ZF 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

Tungaloy B097
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel CL LH H L H LH CL CL CL
M Stainless C L L C L
K Cast iron CL C L CL CL CL
Trigon, 80° N Non-ferrous
with hole S Superalloys C L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius
Negative

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

AH630

NS520
T9135
T9125

T6130
T6120

T5105
T9115

T5115
Inch Metric
11 WNMG 431 TN11 WNMG080404-11 0.016" 䖃

WNMG 432 TN11 WNMG080408-11 䖃

Finishing

0.031"

17 WNMG 431 TN17 WNMG080404-17 0.016" 䖃

Finishing of mild

WNMG 432 TN17 WNMG080408-17 0.031" 䖃

steels

SF WNMG 331 SF WNMG060404-SF 0.016" 䖃 䖃 䖃

WNMG 332 SF WNMG060408-SF 0.031" 䖃 䖃 䖃

WNMG 431 SF WNMG080404-SF 0.016" 䖃 䖃 䖃

WNMG 432 SF WNMG080408-SF 0.031" 䖃 䖃 䖃

CF WNMG 431 CF WNMG080404-CF 0.016" 䖃 䖃

WNMG 432 CF WNMG080408-CF 0.031" 䖃 䖃

WNMG 433 CF WNMG080412-CF 0.047" 䖃 䖃

Finishing

HRF WNMG 431 HRF WNMG080404-HRF 0.016" 䖃 䖃

WNMG 432 HRF WNMG080408-HRF 0.031" 䖃 䖃

TS WNMG 431 TS WNMG080404-TS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 432 TS WNMG080408-TS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 TS WNMG080412-TS 0.047" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

B098 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H L H CL LH H CL CL

Insert
M Stainless C L CL L H CL
K Cast iron CL CL CL CL L CL CL
Trigon, 80° N Non-ferrous
with hole S Superalloys CL
H Hard materials
Coated Cermet
Application

Corner
radius

Negative
NS9530
Chipbreaker Designation

GH330
AH630
AH645
AH120
T9105

T9135
T9125

T6130
T6120
T9115

T5115
T515
Inch Metric
SW WNMG 332E-SW WNMG060408E-SW 0.031" 䖃 䖃 䖃 䖃
Finishing to medium cutting (Wiper)

WNMG 333E-SW WNMG060412E-SW 0.047" 䖃 䖃 䖃 䖃

WNMG 432 SW WNMG080408-SW 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 433 SW WNMG080412-SW 0.047" 䖃 䖃 䖃 䖃

ASW WNMG 332 ASW WNMG060408-ASW 0.031" 䖃 䖃 䖃

WNMG 333 ASW WNMG060412-ASW 0.047" 䖃 䖃 䖃 䖃
WNMG 432 ASW WNMG080408-ASW 0.031" 䖃 䖃 䖃 䖃
WNMG 433 ASW WNMG080412-ASW 0.047" 䖃 䖃 䖃 䖃

AS WNMG 431 AS WNMG080404-AS 0.016" 䖃 䖃

small depth of cut

WNMG 432 AS WNMG080408-AS 0.031" 䖃 䖃 䖃 䖃 䖃

High feed,

WNMG 433 AS WNMG080412-AS 0.047" 䖃 䖃 䖃 䖃

CB WNMG 331 CB WNMG060404-CB 0.016" 䖃 䖃

(Double sided)

WNMG 332 CB WNMG060408-CB 0.031" 䖃 䖃

Boring

NS WNMG 431 NS WNMG080404-NS 0.016" 䖃 䖃 䖃

WNMG 432 NS WNMG080408-NS 0.031" 䖃 䖃 䖃

Finishing

SS WNMG 331E-SS WNMG060404E-SS 0.016" 䖃 䖃

WNMG 332E-SS WNMG060408E-SS 0.031" 䖃 䖃

WNMG 333E-SS WNMG060412E-SS 0.047" 䖃 䖃

WNMG 431 SS WNMG080404-SS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

W
WNMG 432 SS WNMG080408-SS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 SS WNMG080412-SS 0.047" 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

Tungaloy B099
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel C CL LH H C CL L CL CL
M Stainless C CL L
K Cast iron CL CL C CL L CL CL
Trigon, 80° N Non-ferrous
with hole S Superalloys C CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

AH725
AH120
AH110
T9105

T9135
T9125
T9115
Inch Metric
TM WNMG 331E-TM WNMG060404E-TM 0.016" 䖃 䖃

WNMG 332E-TM WNMG060408E-TM 0.031" 䖃 䖃

WNMG 333E-TM WNMG060412E-TM 0.047" 䖃 䖃

Medium cutting

WNMG 331 TM WNMG060404-TM 0.016" 䖃 䖃 䖃

WNMG 332 TM WNMG060408-TM 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 431 TM WNMG080404-TM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 432 TM WNMG080408-TM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 TM WNMG080412-TM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 434 TM WNMG080416-TM 0.063" 䖃 䖃 䖃 䖃

AM WNMG 432 AM WNMG080408-AM 0.031" 䖃 䖃

WNMG 433 AM WNMG080412-AM 0.047" 䖃 䖃

WNMG 434 AM WNMG080416-AM 0.063" 䖃 䖃

NM WNMG 333E-NM WNMG060412E-NM 0.047" 䖃

WNMG 432 NM WNMG080408-NM 0.031" 䖃 䖃 䖃

Finishing to medium cutting

WNMG 433 NM WNMG080412-NM 0.047" 䖃 䖃 䖃 䖃

TQ WNMG 431 TQ WNMG080404-TQ 0.016" 䖃 䖃

WNMG 432 TQ WNMG080408-TQ 0.031" 䖃 䖃

ZM WNMG 332E-ZM WNMG060408E-ZM 0.031" 䖃 䖃

WNMG 332 ZM WNMG060408-ZM 0.031" 䖃 䖃 䖃

WNMG 333 ZM WNMG060412-ZM 0.047" 䖃 䖃 䖃

WNMG 432 ZM WNMG080408-ZM 0.031" 䖃 䖃 䖃 䖃 䖃

W
WNMG 433 ZM WNMG080412-ZM 0.047" 䖃 䖃 䖃

WNMG 434 ZM WNMG080416-ZM 0.063" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

B100 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H C CL CL CL CL CL C

Insert
M Stainless C CL CL C
K Cast iron CL CL CL C L H C CL CL CL CL CL C
Trigon, 80° N Non-ferrous C
with hole S Superalloys C CL
H Hard materials
Coated Coated Cermet Un-
cermet coated
Application

Corner
radius

Negative
NS9530
Chipbreaker Designation

GH330

NS520
AH120

GT720
AH110
T9105

T9135
T9125

T5105

T5125
T9115

T5115

TH10
T515
Inch Metric
DM WNMG 432 DM WNMG080408-DM 0.031" 䖃 䖃 䖃 䖃
WNMG 433 DM WNMG080412-DM 0.047" 䖃 䖃 䖃 䖃
Medium cutting

All-round WNMG 331 WNMG060404 0.016" 䖃 䖃 䖃 䖃 䖃

WNMG 332 WNMG060408 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 431 WNMG080404 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 432 WNMG080408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 WNMG080412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 434 WNMG080416 0.063" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

27 WNMG 432 TN27 WNMG080408-27 0.031" 䖃 䖃

medium cutting
Finishing to

33 WNMG 431 TN33 WNMG080404-33 0.016" 䖃

WNMG 432 TN33 WNMG080408-33 0.031" 䖃 䖃

WNMG 433 TN33 WNMG080412-33 0.047" 䖃

Medium cutting

37 WNMG 431 TN37 WNMG080404-37 0.016" 䖃

WNMG 432 TN37 WNMG080408-37 0.031" 䖃 䖃 䖃

䖃㻌: Line up
W

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

Tungaloy B101
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel L H LH H C CL L
M Stainless C L L H C CL L C L
K Cast iron CL C L H C CL L CH
Trigon, 80° N Non-ferrous CH
with hole S Superalloys C CL C C L L CH
H Hard materials
Coated Uncoated
Application

Corner
radius
Negative

AH8005
AH8015
Chipbreaker Designation

AH905
AH630
AH645

AH725
AH120
AH110
T6130
T6120

T5105

T5125
T5115

KS20
T515
Inch Metric
SM WNMG 331E-SM WNMG060404E-SM 0.016" 䖃 䖃 䖃
WNMG 332E-SM WNMG060408E-SM 0.031" 䖃 䖃 䖃
WNMG 333E-SM WNMG060412E-SM 0.047" 䖃 䖃 䖃
WNMG 332 SM WNMG060408-SM 0.031" 䖃

WNMG 431 SM WNMG080404-SM 0.016" 䖃 䖃 䖃 䖃

Medium cutting

WNMG 432 SM WNMG080408-SM 0.031" 䖃 䖃 䖃 䖃 䖃

WNMG 433 SM WNMG080412-SM 0.047" 䖃 䖃 䖃 䖃 䖃

CM WNMG 431 CM WNMG080404-CM 0.016" 䖃

WNMG 432 CM WNMG080408-CM 0.031" 䖃 䖃 䖃 䖃

WNMG 433 CM WNMG080412-CM 0.047" 䖃 䖃 䖃 䖃

HRM WNMG 431 HRM WNMG080404-HRM 0.016" 䖃 䖃

medium cutting
Finishing to

WNMG 432 HRM WNMG080408-HRM 0.031" 䖃 䖃

WNMG 433 HRM WNMG080412-HRM 0.047" 䖃 䖃

HMM WNMG 431 HMM WNMG080404-HMM 0.016" 䖃

WNMG 432 HMM WNMG080408-HMM 0.031" 䖃

WNMG 433 HMM WNMG080412-HMM 0.047" 䖃

Medium cutting

SA WNMG 432 SA WNMG080408-SA 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 SA WNMG080412-SA 0.047" 䖃 䖃 䖃 䖃 䖃

W 䖃㻌: Line up

Reference pages
External toolholders → B202 - Internal toolholders → B295 -
TungCap → B224, F009 -

B102 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel C CL LH H H LH H CL CL C

Insert
M Stainless L L H CL C
K Cast iron CL CL CL C L H CL CL CL C
Trigon, 80° N Non-ferrous C
with hole S Superalloys CL
H Hard materials C
Coated Un- Ceramics
Cermet coated
Application

Corner
radius

Negative
Chipbreaker Designation

AH630
AH645

NS520
AH120

FX105
T9105

T9135
T9125

T6130

T5105

T5125
T9115

T5115

TH10

LX11
T515
Inch Metric
TH WNMG 432 TH WNMG080408-TH 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

WNMG 433 TH WNMG080412-TH 0.047" 䖃 䖃 䖃 䖃 䖃

WNMG 434 TH WNMG080416-TH 0.063" 䖃 䖃 䖃

WNMG 543 TH WNMG100612-TH 0.047" 䖃 䖃 䖃

WNMG 544 TH WNMG100616-TH 0.063" 䖃 䖃

THS WNMG 432 THS WNMG080408-THS 0.031" 䖃 䖃 䖃 䖃

WNMG 433 THS WNMG080412-THS 0.047" 䖃 䖃 䖃 䖃
Medium to heavy cutting

WNMG 434 THS WNMG080416-THS 0.063" 䖃 䖃

WNMG 543 THS WNMG100612-THS 0.047" 䖃 䖃 䖃 䖃

WNMG 544 THS WNMG100616-THS 0.063" 䖃 䖃 䖃

SH WNMG 432 SH WNMG080408-SH 0.031" 䖃 䖃 䖃

WNMG 433 SH WNMG080412-SH 0.047" 䖃 䖃 䖃

CH WNMG 432 CH WNMG080408-CH 0.031" 䖃 䖃 䖃

WNMG 433 CH WNMG080412-CH 0.047" 䖃 䖃 䖃

- WNMA 431 WNMA080404 0.016" 䖃 䖃 䖃 䖃

Finishing to medium

WNMA 432 WNMA080408 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

WNMA 433 WNMA080412 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

cutting

WNMA 434 WNMA080416 0.063" 䖃 䖃 䖃 䖃

WNGA 431 WNGA080404 0.016" 䖃

WNGA 432 WNGA080408 0.031" 䖃

WNGA 433 WNGA080412 0.047" 䖃

W
䖃㻌: Line up

Reference pages
External toolholders → B210 - Internal toolholders → B322 -
TungCap → B224, F009 -

Tungaloy B103
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert N E G AT I V E T Y P E P Steel LH H CL CL
M Stainless
K Cast iron CL CL
Rhombic, 25° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated Coated cermet Cermet
Application

Corner
radius
Negative

NS9530
GT9530
Chipbreaker Designation

T9125
T9135
Inch Metric
ZF YNMG 331 ZF YNMG160404-ZF 0.016" 䖃 䖃 䖃 䖃

YNMG 332 ZF YNMG160408-ZF 0.031" 䖃 䖃 䖃 䖃

Finishing

ZM YNMG 331 ZM YNMG160404-ZM 0.016" 䖃 䖃 䖃 䖃

medium cutting
Finishing to

YNMG 332 ZM YNMG160408-ZM 0.031" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
YNMG... : External toolholders → B211 -, B217, Internal toolholders → B325, B328
TungCap → B224

B104 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

N E G AT I V E T Y P E P Steel CL

Insert
M Stainless CL
K Cast iron CL
Parallelogram, 55° N Non-ferrous
without hole S Superalloys
H Hard materials
Coated
Application

Corner
radius

Negative
Chipbreaker Designation

GH330
Inch Metric
S1 KNMX160405R-S1 0.020" 䖃
Finishing

KNMX160405L-S1 0.020" 䖃

P Steel
M Stainless
K Cast iron CL
Hexagon, 120° N Non-ferrous
without hole S Superalloys
H Hard materials
Ceramics
Application

Corner
radius

Chipbreaker Designation
FX105

Inch Metric
- HNGD 453 HNGD050712 0.047" 䖃
medium cutting
Finishing to

HNGD 454 HNGD050716 0.063" 䖃

䖃㻌: Line up

OTHERS

Reference pages
KNMX... : External toolholders → B256
HNGD... : External toolholders → B273

Tungaloy B105
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L H C CL L L CL CL CL CL
M Stainless C L C CL L C L L CL CL
Rhombic, 80° K Cast iron CL C CL L L CL CL
with hole N Non-ferrous
Positive 7° S Superalloys C CL C C L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

GH730
AH725

SH725
AH120
AH110
T9125

T6130
T6120
T9115

J740
Inch Metric
01 CCGT 21.50.5-01 CCGT060202-01 0.008" 䖃

CCGT 32.50.5-01 CCGT09T302-01 0.008" 䖃

Precision
Positive

finishing
Precision finishing

01 CCGT 21.50.5 F-01 CCGT060202F-01 0.008" 䖃

(Sharp edge)

CCGT 21.51 F-01 CCGT060204F-01 0.016" 䖃

CCGT 32.50.5 F-01 CCGT09T302F-01 0.008" 䖃

PSF CCMT 21.50.5 PSF CCMT060202-PSF 0.008" 䖃 䖃 䖃

CCMT 21.51 PSF CCMT060204-PSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.50.5 PSF CCMT09T302-PSF 0.008" 䖃 䖃

CCMT 32.51 PSF CCMT09T304-PSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.52 PSF CCMT09T308-PSF 0.031" 䖃 䖃 䖃 䖃 䖃

Finishing

PF CCMT 21.50.5 PF CCMT060202-PF 0.008" 䖃 䖃 䖃 䖃

CCMT 21.51 PF CCMT060204-PF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
CCMT 21.52 PF CCMT060208-PF 0.031" 䖃 䖃 䖃 䖃

CCMT 32.50.5 PF CCMT09T302-PF 0.008" 䖃 䖃 䖃

CCMT 32.51 PF CCMT09T304-PF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.52 PF CCMT09T308-PF 0.031" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

B106 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L L CL CL

Insert
M Stainless C L L H CL L C L L
Rhombic, 80° K Cast iron CL CL L L CL CL
with hole N Non-ferrous
Positive 7° S Superalloys CL C C L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

GH730
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115
Inch Metric
PSS CCMT 21.51 PSS CCMT060204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing to light cutting

CCMT 21.52 PSS CCMT060208-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive
CCMT 32.51 PSS CCMT09T304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.52 PSS CCMT09T308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 431 PSS CCMT120404-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 432 PSS CCMT120408-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 433 PSS CCMT120412-PSS 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

PS CCMT 21.50.5 PS CCMT060202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 21.51 PS CCMT060204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 21.52 PS CCMT060208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.50.5 PS CCMT09T302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

CCMT 32.51 PS CCMT09T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.52 PS CCMT09T308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 431 PS CCMT120404-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 432 PS CCMT120408-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 433 PS CCMT120412-PS 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
23 CCMT 21.50.5-23 CCMT060202-23 0.008" 䖃 䖃

CCMT 21.51-23 CCMT060204-23 0.016" 䖃 䖃

CCMT 21.52-23 CCMT060208-23 0.031" 䖃

CCMT 32.51-23 CCMT09T304-23 0.016" 䖃 䖃

CCMT 32.52-23 CCMT09T308-23 0.031" 䖃 䖃

SW CCMT 21.51-SW CCMT060204-SW 0.016" 䖃 䖃 䖃

Finishing to medium
cutting Wiper

CCMT 21.52-SW CCMT060208-SW 0.031" 䖃 䖃 䖃

CCMT 32.51-SW CCMT09T304-SW 0.016" 䖃 䖃 䖃

CCMT 32.52-SW CCMT09T308-SW 0.031" 䖃 䖃 䖃

24 CCMT 21.50.5-24 CCMT060202-24 0.008" 䖃 䖃

CCMT 21.51-24 CCMT060204-24 0.016" 䖃 䖃 䖃 䖃 䖃

Medium cutting

CCMT 21.52-24 CCMT060208-24 0.031" 䖃 䖃 䖃 䖃 䖃

CCMT 32.50.5-24 CCMT09T302-24 0.008" 䖃 䖃

CCMT 32.51-24 CCMT09T304-24 0.016" 䖃 䖃 䖃 䖃 䖃

CCMT 32.52-24 CCMT09T308-24 0.031" 䖃 䖃 䖃 䖃 䖃

CCMT 432-24 CCMT120408-24 0.031" 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up
Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

Tungaloy B107
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL CL C
M Stainless CL CL C
Rhombic, 80° K Cast iron C
with hole N Non-ferrous C
Positive 7° S Superalloys CL
H Hard materials
Coated Uncoated
Application

Corner
radius
Chipbreaker Designation

SH730
SH725

TH10
Inch Metric
W08 CCGT 4.51.8V R-W08 CCGT03X100R-W08 0.0012" 䖃 䖃

CCGT 4.51.8V L-W08 CCGT03X100L-W08 0.0012" 䖃 䖃

Positive

CCGT 4.51.80 R-W08 CCGT03X101R-W08 0.004" 䖃 䖃

CCGT 4.51.80 L-W08 CCGT03X101L-W08 0.004" 䖃 䖃

CCGT 4.51.80.5 R-W08 CCGT03X102R-W08 0.008" 䖃 䖃

CCGT 4.51.80.5 L-W08 CCGT03X102L-W08 0.008" 䖃 䖃

CCGT 4.51.81 R-W08 CCGT03X104R-W08 0.016" 䖃 䖃

䖃 䖃
Finishing

CCGT 4.51.81 L-W08 CCGT03X104L-W08 0.016"

CCGT 5.52.2V R-W08 CCGT04T100R-W08 0.0012" 䖃 䖃

CCGT 5.52.2V L-W08 CCGT04T100L-W08 0.0012" 䖃 䖃

CCGT 5.52.20 R-W08 CCGT04T101R-W08 0.004" 䖃 䖃

CCGT 5.52.20 L-W08 CCGT04T101L-W08 0.004" 䖃 䖃

CCGT 5.52.20.5 R-W08 CCGT04T102R-W08 0.008" 䖃 䖃

CCGT 5.52.20.5 L-W08 CCGT04T102L-W08 0.008" 䖃 䖃

CCGT 5.52.21 R-W08 CCGT04T104R-W08 0.016" 䖃 䖃

CCGT 5.52.21 L-W08 CCGT04T104L-W08 0.016" 䖃 䖃

W08 CCGT 4.51.8V FL-W08 CCGT03X100FL-W08 0.0012" 䖃

C
CCGT 4.51.8V FR-W08 CCGT03X100FR-W08 0.0012" 䖃

CCGT 4.51.80 FL-W08 CCGT03X101FL-W08 0.004" 䖃

CCGT 4.51.80 FR-W08 CCGT03X101FR-W08 0.004" 䖃

CCGT 4.51.80.5 FL-W08 CCGT03X102FL-W08 0.008" 䖃

Finishing (Sharp edge)

CCGT 4.51.80.5 FR-W08 CCGT03X102FR-W08 0.008" 䖃

CCGT 4.51.81 FL-W08 CCGT03X104FL-W08 0.016" 䖃

CCGT 4.51.81 FR-W08 CCGT03X104FR-W08 0.016" 䖃

CCGT 5.52.2V FL-W08 CCGT04T100FL-W08 0.0012" 䖃

CCGT 5.52.2V FR-W08 CCGT04T100FR-W08 0.0012" 䖃

CCGT 5.52.20 FL-W08 CCGT04T101FL-W08 0.004" 䖃

CCGT 5.52.20 FR-W08 CCGT04T101FR-W08 0.004" 䖃

CCGT 5.52.20.5 FL-W08 CCGT04T102FL-W08 0.008" 䖃

CCGT 5.52.20.5 FR-W08 CCGT04T102FR-W08 0.008" 䖃

CCGT 5.52.21 FL-W08 CCGT04T104FL-W08 0.016" 䖃

CCGT 5.52.21 FR-W08 CCGT04T104FR-W08 0.016" 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B299 -

B108 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H C CL L C CL L CL CL C L

Insert
M Stainless C L L H C CL L C CL L C L
Rhombic, 80° K Cast iron CL CL L C CL L C CL L CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C CL C C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH330
GH730
AH630
AH645

AH725
AH120

GH110
AH110
T9125

T6130
T6120
T9115

T5115

UX30
TH10
T515
Inch Metric
W15 CCGT 21.5VR-W15 CCGT060200R-W15 0.0012" 䖃

CCGT 21.5VL-W15 CCGT060200L-W15 0.0012" 䖃 䖃

Positive
CCGT 21.50.5R-W15 CCGT060202R-W15 0.008" 䖃 䖃

CCGT 21.50.5L-W15 CCGT060202L-W15 0.008" 䖃 䖃 䖃

CCGT 21.51R-W15 CCGT060204R-W15 0.016" 䖃 䖃 䖃

CCGT 21.51L-W15 CCGT060204L-W15 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

W20 CCGT32.50.5R-W20 CCGT09T302R-W20 0.008" 䖃 䖃

CCGT32.50.5L-W20 CCGT09T302L-W20 0.008" 䖃 䖃 䖃

CCGT32.51R-W20 CCGT09T304R-W20 0.016" 䖃

CCGT32.51L-W20 CCGT09T304L-W20 0.016" 䖃 䖃 䖃 䖃 䖃

CCGT32.52R-W20 CCGT09T308R-W20 0.031" 䖃

CCGT32.52L-W20 CCGT09T308L-W20 0.031" 䖃 䖃

PM CCMT 21.51 PM CCMT060204-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 21.52 PM CCMT060208-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

CCMT 32.51 PM CCMT09T304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 32.52 PM CCMT09T308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
CCMT 32.53 PM CCMT09T312-PM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CCMT 432 PM CCMT120408-PM 0.031" 䖃 䖃 䖃 䖃 䖃

CCMT 433 PM CCMT120412-PM 0.047" 䖃 䖃 䖃 䖃 䖃

CM CCMT 21.51 CM CCMT060204-CM 䖃 䖃

Finishing to medium cutting

0.016"

CCMT 21.52 CM CCMT060208-CM 0.031" 䖃 䖃

CCMT 32.51 CM CCMT09T304-CM 0.016" 䖃 䖃

CCMT 32.52 CM CCMT09T308-CM 0.031" 䖃 䖃

CCMT 32.53 CM CCMT09T312-CM 0.047" 䖃

CCMT 431 CM CCMT120404-CM 0.016" 䖃

CCMT 432 CM CCMT120408-CM 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

Tungaloy B109
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel C CL CL C
M Stainless C CL C
Rhombic, 80° K Cast iron L C CL C C
with hole N Non-ferrous C C
Positive 7° S Superalloys C C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

KS05F
SH725
GH110
T5115

TH10
Inch Metric
AL CCGT 21.50 AL CCGT060201-AL 0.004" 䖃 䖃

CCGT 21.50.5 AL CCGT060202-AL 0.008" 䖃 䖃

Positive

CCGT 21.51 AL CCGT060204-AL 0.016" 䖃

CCGT 32.50 AL CCGT09T301-AL 0.004" 䖃

CCGT 32.50.5 AL CCGT09T302-AL 0.008" 䖃 䖃

CCGT 32.51 AL CCGT09T304-AL 0.016" 䖃 䖃

CCGT 32.52 AL CCGT09T308-AL 0.031" 䖃

CCGT 430.5 AL CCGT120402-AL 0.008" 䖃

CCGT 431 AL CCGT120404-AL 0.016" 䖃

CCGT 432 AL CCGT120408-AL 0.031" 䖃

All-round CCGT 21.50.5 CCGT060202 0.008" 䖃

CCGT 21.51 CCGT060204 0.016" 䖃

CCGT 32.50.5 CCGT09T302 0.008" 䖃

Finishing to medium cutting

CCGT 32.51 CCGT09T304 0.016" 䖃

CCGT 32.52 CCGT09T308 0.031" 䖃

Angular CCGT 21.5 R CCGT060200R 0.0012" 䖃

C
CCGT 21.50.5 R CCGT060202R 0.008" 䖃

CCGT 21.50.5 L CCGT060202L 0.008" 䖃

CCGT 21.51 L CCGT060204L 0.016" 䖃

CCGT 32.50.5 R CCGT09T302R 0.008" 䖃

CCGT 32.50.5 L CCGT09T302L 0.008" 䖃

CCGT 32.51 R CCGT09T304R 0.016" 䖃

CCGT 32.51 L CCGT09T304L 0.016" 䖃

- CCMW 21.51 CCMW060204 0.016" 䖃

CCMW 21.52 CCMW060208 0.031" 䖃

CCMW 32.51 CCMW09T304 0.016" 䖃

CCMW 32.52 CCMW09T308 0.031" 䖃

- CCGW 21.50.5 CCGW060202 0.008" 䖃

CCGW 21.51 CCGW060204 0.016" 䖃

CCGW 32.51 CCGW09T304 0.016" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

B110 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel L CL CL

Insert
M Stainless L CL CL
Rhombic, 80° K Cast iron L
with hole N Non-ferrous
Positive 7° S Superalloys C CL
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

AH725

SH730
SH725
Inch Metric
JS CCGT 4.51.80 JS CCGT03X101-JS 0.004" 䖃 㻌
For internal turning

CCGT 4.51.80.5 JS CCGT03X102-JS 0.008" 䖃

Positive
on small lathes

CCGT 4.51.81 JS CCGT03X104-JS 0.016" 䖃

CCGT 5.52.20 JS CCGT04T101-JS 0.004" 䖃

CCGT 5.52.20.5 JS CCGT04T102-JS 0.008" 䖃

CCGT 5.52.21 JS CCGT04T104-JS 0.016" 䖃

JS CCGT 4.51.80 F-JS CCGT03X101F-JS 䖃

small lathes (Sharp edge)

0.004"
For internal turning on

CCGT 4.51.80.5 F-JS CCGT03X102F-JS 0.008" 䖃

CCGT 4.51.81 F-JS CCGT03X104F-JS 0.016" 䖃

CCGT 5.52.20 F-JS CCGT04T101F-JS 0.004" 䖃

CCGT 5.52.20.5 F-JS CCGT04T102F-JS 0.008" 䖃

CCGT 5.52.21 F-JS CCGT04T104F-JS 0.016" 䖃

JS CCGT 21.50 N-JS CCGT060201N-JS 0.004" 䖃

For external turning

CCGT 21.50.5 N-JS CCGT060202N-JS 0.008" 䖃

on small lathes

CCGT 21.51 N-JS CCGT060204N-JS 0.016" 䖃

CCGT 32.50 N-JS CCGT09T301N-JS 0.004" 䖃

C
CCGT 32.50.5 N-JS CCGT09T302N-JS 0.008" 䖃

CCGT 32.51 N-JS CCGT09T304N-JS 0.016" 䖃

JS CCGT 21.5 VFN-JS CCGT060200FN-JS 0.0012" 䖃 䖃

For external turning on small

CCGT 21.50 FN-JS CCGT060201FN-JS 0.004" 䖃 䖃

lathes (Sharp edge)

CCGT 21.50.5 FN-JS CCGT060202FN-JS 0.008" 䖃 䖃

CCGT 21.51 FN-JS CCGT060204FN-JS 0.016" 䖃 䖃

CCGT 32.5 VFN-JS CCGT09T300FN-JS 0.0012" 䖃 䖃

CCGT 32.50 FN-JS CCGT09T301FN-JS 0.004" 䖃 䖃

CCGT 32.50.5 FN-JS CCGT09T302FN-JS 0.008" 䖃 䖃

CCGT 32.51 FN-JS CCGT09T304FN-JS 0.016" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

Tungaloy B111
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL CL CL C
M Stainless CL CL C
Rhombic, 80° K Cast iron CL C
with hole N Non-ferrous C
Positive 7° S Superalloys
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

SH725

TH10
J740
Inch Metric
J10 CCGT 21.5V FR-J10 CCGT060200FR-J10 0.0012" 䖃 䖃 䖃

CCGT 21.5V FL-J10 CCGT060200FL-J10 0.0012" 䖃 䖃 䖃

Positive

For external turning on small lathes

CCGT 21.50 FR-J10 CCGT060201FR-J10 0.004" 䖃 䖃 䖃 䖃

CCGT 21.50 FL-J10 CCGT060201FL-J10 0.004" 䖃 䖃 䖃

CCGT 21.50.5 FR-J10 CCGT060202FR-J10 0.008" 䖃 䖃 䖃 䖃

CCGT 21.50.5 FL-J10 CCGT060202FL-J10 0.008" 䖃 䖃 䖃 䖃

(Sharp edge)

CCGT 32.5V FR-J10 CCGT09T300FR-J10 0.0012" 䖃 䖃 䖃

CCGT 32.5V FL-J10 CCGT09T300FL-J10 0.0012" 䖃 䖃 䖃

CCGT 32.50 FR-J10 CCGT09T301FR-J10 0.004" 䖃 䖃 䖃

CCGT 32.50 FL-J10 CCGT09T301FL-J10 0.004" 䖃 䖃 䖃

CCGT 32.50.5 FR-J10 CCGT09T302FR-J10 0.008" 䖃 䖃 䖃

CCGT 32.50.5 FL-J10 CCGT09T302FL-J10 0.008" 䖃 䖃 䖃

CCGT 32.51 FR-J10 CCGT09T304FR-J10 0.016" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B261 Internal toolholders → B299 -, B330
J series toolholders → B362 - B365

B112 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L L CL CL

Insert
M Stainless C L L H CL L L
Rhombic, 80° K Cast iron CL CL L L CL CL
with hole N Non-ferrous
Positive 11° S Superalloys CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH730
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115
Inch Metric
PSF CPMT21.50.5 PSF CPMT060202-PSF 0.008" 䖃

CPMT 21.51 PSF CPMT060204-PSF 0.016" 䖃 䖃 䖃

Positive
CPMT 2.51.50.5 PSF CPMT080202-PSF 0.008" 䖃

CPMT 2.51.51 PSF CPMT080204-PSF 0.016" 䖃 䖃 䖃

CPMT 321 PSF CPMT090302-PSF 0.008" 䖃 䖃 䖃

CPMT 322 PSF CPMT090304-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

Finishing

CPMT 32.50.5 PSF CPMT09T302-PSF 0.008" 䖃

CPMT 32.51 PSF CPMT09T304-PSF 0.016" 䖃 䖃 䖃

PF CPMT 320.5 PF CPMT090302-PF 0.008" 䖃 䖃

CPMT 321 PF CPMT090304-PF 0.016" 䖃 䖃

PSS CPMT 21.51 PSS CPMT060204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃

Finishing to light cutting

CPMT 2.51.51 PSS CPMT080204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 2.51.52 PSS CPMT080208-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 321 PSS CPMT090304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

C
CPMT 322 PSS CPMT090308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 32.51 PSS CPMT09T304-PSS 0.016" 䖃 䖃 䖃

CPMT 32.52 PSS CPMT09T308-PSS 0.031" 䖃 䖃 䖃

PS CPMT 21.50.5 PS CPMT060202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 21.51 PS CPMT060204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

CPMT 2.51.50.5 PS CPMT080202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 2.51.51 PS CPMT080204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 2.51.52 PS CPMT080208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 321 PS CPMT090304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 322 PS CPMT090308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 32.50.5 PS CPMT09T302-PS 0.008" 䖃 䖃 䖃 䖃

CPMT 32.51 PS CPMT09T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃

CPMT 32.52 PS CPMT09T308-PS 0.031" 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B303 -, B330

Tungaloy B113
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel LH CL C
M Stainless C
Rhombic, 80° K Cast iron CL C
with hole N Non-ferrous C
Positive 11° S Superalloys
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

T9125

TH10
Inch Metric
24 CPMT 432-24 CPMT120408-24 0.031" 䖃
Medium cutting

CPMT 53.52-24 CPMT160508-24 0.031" 䖃 䖃

Positive

CPMT 53.53-24 CPMT160512-24 0.047" 䖃

W15 CPGT 730.5FL-W15 CPGT050202L-W15 0.008" 䖃

CPGT 731FL-W15 CPGT050204L-W15 0.016" 䖃

CPGT 2.51.50.5FR-W15 CPGT080202R-W15 0.008" 䖃

CPGT 2.51.50.5FL-W15 CPGT080202L-W15 0.008" 䖃 䖃

CPGT 2.51.51FR-W15 CPGT080204R-W15 0.016" 䖃

Finishing

CPGT 2.51.51FL-W15 CPGT080204L-W15 0.016" 䖃 䖃

W20 CPMW 320.5R W20 CPGT090302R-W20 0.008" 䖃 䖃

CPMW 320.5L W20 CPGT090302L-W20 0.008" 䖃 䖃

CPMW 321R W20 CPGT090304R-W20 0.016" 䖃 䖃

CPMW 321L W20 CPGT090304L-W20 0.016" 䖃 䖃

C
䖃㻌: Line up

Reference pages
Internal toolholders → B303 -, B330

B114 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel C L H LH H L CL

Insert
M Stainless C L L H L C L
Rhombic, 80° K Cast iron CL CL C L L CL
with hole N Non-ferrous
Positive 11° S Superalloys C C L L
H Hard materials
Coated Cermet
Application

Corner
radius

AH8005

NS9530
AH8015
Chipbreaker Designation

AH905
AH630
AH645

AH725
T9105
T9125

T6130
T6120

T5115
T515
Inch Metric
PM CPMT 21.51 PM CPMT060204-PM 0.016" 䖃 䖃 䖃 䖃 䖃
Medium cutting

CPMT 21.52 PM CPMT060208-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

Positive
CPMT 321 PM CPMT090304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CPMT 322 PM CPMT090308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CM CPMT 21.51 CM CPMT060204-CM 0.016" 䖃

CPMT 21.52 CM CPMT060208-CM 0.031" 䖃

Finishing to medium cutting

CPMT 2.51.51 CM CPMT080204-CM 0.016" 䖃

CPMT 2.51.52 CM CPMT080208-CM 0.031" 䖃

CPMT 321 CM CPMT090304-CM 0.016" 䖃 䖃

CPMT 322 CM CPMT090308-CM 0.031" 䖃 䖃

CPMT 32.51 CM CPMT09T304-CM 0.016" 䖃 䖃

CPMT 32.52 CM CPMT09T308-CM 0.031" 䖃 䖃

CPMT 32.53 CM CPMT09T312-CM 0.047" 䖃

CPMT 432 CM CPMT120408-CM 0.031" 䖃

CPMT 433 CM CPMT120412-CM 0.047" 䖃

All-round CPMT 432 CPMT120408 0.031" 䖃 䖃 䖃

C
Medium cutting

- CPMW 2.51.51 CPMW080204 0.016" 䖃

CPMW 2.51.52 CPMW080208 0.031" 䖃

CPMW 321 CPMW090304 0.016" 䖃 䖃

CPMW 322 CPMW090308 0.031" 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B303 -, B330

Tungaloy B115
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L L CL CL CL CL CL
M Stainless L C L L CL CL
Rhombic, 55° K Cast iron CL L L CL CL CL
with hole N Non-ferrous
Positive 7° S Superalloys C C L L
H Hard materials
Coated Coated cermet Cermet
Application

Corner
radius

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

GH730
AH905
AH725

SH725

J9530
T9125
T9115

J740
Inch Metric
01 DCGT 21.50.5-01 DCGT070202-01 0.008" 䖃 䖃

DCGT 32.50.5-01 DCGT11T302-01 0.008" 䖃

Positive

Precision
finishing
Precision finishing

01 DCGT 21.50.5 F-01 DCGT070202F-01 0.008" 䖃

(Sharp edge)

DCGT 32.50.5 F-01 DCGT11T302F-01 0.008" 䖃

PSF DCMT 21.50.5 PSF DCMT070202-PSF 0.008" 䖃 䖃 䖃

DCMT 21.51 PSF DCMT070204-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

DCMT 32.50.5 PSF DCMT11T302-PSF 0.008" 䖃 䖃 䖃

DCMT 32.51 PSF DCMT11T304-PSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.52 PSF DCMT11T308-PSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

PF DCMT 21.50.5 PF DCMT070202-PF 0.008" 䖃 䖃 䖃

DCMT 21.51 PF DCMT070204-PF 0.016" 䖃 䖃 䖃

DCMT 21.52 PF DCMT070208-PF 0.031" 䖃 䖃

D DCMT 32.50.5 PF DCMT11T302-PF 0.008" 䖃 䖃 䖃

DCMT 32.51 PF DCMT11T304-PF 0.016" 䖃 䖃 䖃

DCMT 32.52 PF DCMT11T308-PF 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B313 -
J series toolholders → B365 - B369

B116 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L L CL CL

Insert
M Stainless C L L H CL L C L L
Rhombic, 55° K Cast iron CL CL L L CL CL
with hole N Non-ferrous
Positive 7° S Superalloys CL C C L L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

GH730
AH905
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115
Inch Metric
PSS DCMT 21.51 PSS DCMT070204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing to light

DCMT 21.52 PSS DCMT070208-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive
cutting

DCMT 32.51 PSS DCMT11T304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.52 PSS DCMT11T308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.53 PSS DCMT11T312-PSS 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

PS DCMT 21.50.5 PS DCMT070202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 21.51 PS DCMT070204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 21.52 PS DCMT070208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

DCMT 32.50.5 PS DCMT11T302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.51 PS DCMT11T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.52 PS DCMT11T308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.53 PS DCMT11T312-PS 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

23 DCMT 21.51-23 DCMT070204-23 0.016" 䖃

DCMT 32.51 23 DCMT11T304-23 0.016" 䖃

DCMT 32.52-23 DCMT11T308-23 0.031" 䖃

24 DCMT 21.50.5-24 DCMT070202-24 0.008" 䖃 D

DCMT 21.51-24 DCMT070204-24 0.016" 䖃 䖃 䖃 䖃
Medium cutting

DCMT 21.52-24 DCMT070208-24 0.031" 䖃 䖃 䖃

DCMT 32.50.5-24 DCMT11T302-24 0.008" 䖃 䖃 䖃

DCMT 32.51-24 DCMT11T304-24 0.016" 䖃 䖃 䖃 䖃

DCMT 32.52-24 DCMT11T308-24 0.031" 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B313 -
J series toolholders → B365 - B369

Tungaloy B117
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L H LH H CL L CL L CL CL C
M Stainless C L L H CL L CL L C
Rhombic, 55° K Cast iron CL CL L CL L CL L CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys CL C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH330
GH730
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115

T5115

TH10
T515
Inch Metric
W10 DCGT 21.5VR-W10 DCGT070200R-W10 0.0012" 䖃

DCGT 21.5VL-W10 DCGT070200L-W10 0.0012" 䖃

Positive

DCGT 21.50.5R-W10 DCGT070202R-W10 0.008" 䖃 䖃

DCGT21.50.5L-W10 DCGT070202L-W10 0.008" 䖃 䖃

DCGT 21.51R-W10 DCGT070204R-W10 0.016" 䖃 䖃 䖃

DCGT 21.51L-W10 DCGT070204L-W10 0.016" 䖃 䖃 䖃 䖃

Finishing

W15 DCGT 32.50.5R-W15 DCGT11T302R-W15 0.008" 䖃 䖃

DCGT 32.50.5L-W15 DCGT11T302L-W15 0.008" 䖃 䖃

DCGT 32.51R-W15 DCGT11T304R-W15 0.016" 䖃

DCGT 32.51L-W15 DCGT11T304L-W15 0.016" 䖃 䖃 䖃 䖃

DCGT 32.52R-W15 DCGT11T308R-W15 0.031" 䖃 䖃

DCGT 32.52L-W15 DCGT11T308L-W15 0.031" 䖃 䖃

PM DCMT 21.51 PM DCMT070204-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

DCMT 21.52 PM DCMT070208-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.51 PM DCMT11T304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.52 PM DCMT11T308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

DCMT 32.53 PM DCMT11T312-PM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

D
CM DCMT 21.51 CM DCMT070204-CM 0.016" 䖃
Finishing to medium

DCMT 21.52 CM DCMT070208-CM 0.031" 䖃

cutting

DCMT 32.51 CM DCMT11T304-CM 0.016" 䖃 䖃

DCMT 32.52 CM DCMT11T308-CM 0.031" 䖃 䖃

DCMT 32.53 CM DCMT11T312-CM 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B313 -
J series toolholders → B365 - B369

B118 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel C C CL C

Insert
M Stainless C C
Rhombic, 55° K Cast iron CL L C CL C C
with hole N Non-ferrous C C
Positive 7° S Superalloys C C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

KS05F
GH110
T9105
T5115

TH10
Inch Metric
AL DCGT 21.50.5 AL DCGT070202-AL 0.008" C
DCGT 21.51 AL DCGT070204-AL 0.016" C

Positive
DCGT 32.50.5 AL DCGT11T302-AL 0.008" C
DCGT 32.51 AL DCGT11T304-AL 0.016" C
DCGT 32.52 AL DCGT11T308-AL 0.031" C

All-round DCGT 21.50.5 DCGT070202 0.008" 䖃

Finishing to medium cutting

DCGT 21.51 DCGT070204 0.016" 䖃

DCGT 32.50.5 DCGT11T302 0.008" 䖃

DCGT 32.51 DCGT11T304 0.016" 䖃

DCGT 32.52 DCGT11T308 0.031" 䖃

Angular DCGT 21.50.5 R DCGT070202R 0.008" 䖃

DCGT 21.50.5 L DCGT070202L 0.008" 䖃

DCGT 21.51 R DCGT070204R 0.016" 䖃

DCGT 21.51 L DCGT070204L 0.016" 䖃

DCGT 32.50.5 R DCGT11T302R 0.008" 䖃

DCGT 32.50.5 L DCGT11T302L 0.008" 䖃

DCGT 32.51 R DCGT11T304R 0.016" 䖃

DCGT 32.51 L DCGT11T304L 0.016" 䖃 D

- DCMW 21.51 DCMW070204 0.016" 䖃 䖃

DCMW 21.52 DCMW070208 0.031" 䖃

DCMW 32.51 DCMW11T304 0.016" 䖃 䖃

Medium cutting

DCMW 32.52 DCMW11T308 0.031" 䖃

- DCGW 21.50.5 DCGW070202 0.008" 䖃

DCGW 21.51 DCGW070204 0.016" 䖃 䖃

DCGW 32.51 DCGW11T304 0.016" 䖃

DCGW 32.52 DCGW11T308 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B313 -
J series toolholders → B365 - B369

Tungaloy B119
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel L CL CL
M Stainless L CL CL
Rhombic, 55° K Cast iron L
with hole N Non-ferrous
Positive 7° S Superalloys C CL
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

AH725

SH730
SH725
Inch Metric
JS DCGT 21.5 VFN-JS DCGT070200FN-JS 0.0012" 䖃 䖃
For external turning on small

DCGT 21.50 FN-JS DCGT070201FN-JS 0.004" 䖃 䖃

Positive

lathes (Sharp edge)

DCGT 21.50.5 FN-JS DCGT070202FN-JS 0.008" 䖃 䖃

DCGT 32.5 VFN-JS DCGT11T300FN-JS 0.0012" 䖃 䖃

DCGT 32.50 FN-JS DCGT11T301FN-JS 0.004" 䖃 䖃

DCGT 32.50.5 FN-JS DCGT11T302FN-JS 0.008" 䖃 䖃

DCGT 32.51 FN-JS DCGT11T304FN-JS 0.016" 䖃 䖃

JS DCGT 21.50 N-JS DCGT070201N-JS 0.004" 䖃

For external turning
on small lathes

DCGT 21.50.5 N-JS DCGT070202N-JS 0.008" 䖃

DCGT 32.50 N-JS DCGT11T301N-JS 0.004" 䖃

DCGT 32.50.5 N-JS DCGT11T302N-JS 0.008" 䖃

DCGT 32.51 N-JS DCGT11T304N-JS 0.016" 䖃

JPP DCET 21.5U MFR JPP DCET0702008MFR-JPP <0.0031"* 䖃 䖃

DCET 21.5U MFL JPP DCET0702008MFL-JPP <0.0031"* 䖃 䖃

For external turning on small lathes (Sharp edge)

DCET 21.50 MFR JPP DCET070201MFR-JPP <0.004"* 䖃 䖃

DCET 21.50 MFL JPP DCET070201MFL-JPP <0.004"* 䖃 䖃

DCET 21.50.4 MFR JPP DCET0702018MFR-JPP <0.007"* 䖃 䖃

D DCET 21.50.4 MFL JPP DCET0702018MFL-JPP <0.007"* 䖃 䖃

DCET 21.50.5 MFR JPP DCET070202MFR-JPP <0.008"* 䖃 䖃

DCET 21.50.5 MFL JPP DCET070202MFL-JPP <0.008"* 䖃 䖃

DCET 32.5U MFR JPP DCET11T3008MFR-JPP <0.0031"* 䖃 䖃

DCET 32.5U MFL JPP DCET11T3008MFL-JPP <0.0031"* 䖃 䖃

DCET 32.50 MFR JPP DCET11T301MFR-JPP <0.004"* 䖃 䖃

DCET 32.50 MFL JPP DCET11T301MFL-JPP <0.004"* 䖃 䖃

DCET 32.50.4 MFR JPP DCET11T3018MFR-JPP <0.007"* 䖃 䖃

DCET 32.50.4 MFL JPP DCET11T3018MFL-JPP <0.007"* 䖃 䖃

DCET 32.50.5 MFR JPP DCET11T302MFR-JPP <0.008"* 䖃 䖃

DCET 32.50.5 MFL JPP DCET11T302MFL-JPP <0.008"* 䖃 䖃

* Corner radius has minus tolerance.

Note: See page B051 for chipbreaker descriptions. 䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B312 -
J series toolholders → B365 - B369

B120 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL CL CL CL C

Insert
M Stainless CL CL CL C
Rhombic, 55° K Cast iron CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
Chipbreaker Designation

SH730
SH725

J9530

TH10
J740
Inch Metric
JRP DCET 21.5U MFR JRP DCET0702008MFR-JRP <0.0031"* 䖃 䖃
DCET 21.5U MFL JRP DCET0702008MFL-JRP <0.0031"* 䖃 䖃

Positive
DCET 21.50 MFR JRP DCET070201MFR-JRP <0.004"* 䖃 䖃
DCET 21.50 MFL JRP DCET070201MFL-JRP <0.004"* 䖃 䖃
DCET 21.50.4 MFR JRP DCET0702018MFR-JRP <0.007"* 䖃 䖃
DCET 21.50.4 MFL JRP DCET0702018MFL-JRP <0.007"* 䖃 䖃
DCET 21.50.5 MFR JRP DCET070202MFR-JRP <0.008"* 䖃 䖃
DCET 21.50.5 MFL JRP DCET070202MFL-JRP <0.008"* 䖃 䖃
DCET 32.5U MFR JRP DCET11T3008MFR-JRP <0.0031"* 䖃 䖃
DCET 32.5U MFL JRP DCET11T3008MFL-JRP <0.0031"* 䖃 䖃
DCET 32.50 MFR JRP DCET11T301MFR-JRP <0.004"* 䖃 䖃
DCET 32.50 MFL JRP DCET11T301MFL-JRP <0.004"* 䖃 䖃
DCET 32.50.4 MFR JRP DCET11T3018MFR-JRP <0.007"* 䖃 䖃
For external turning on small lathes (Sharp edge)

DCET 32.50.4 MFL JRP DCET11T3018MFL-JRP <0.007"* 䖃 䖃

DCET 32.50.5 MFR JRP DCET11T302MFR-JRP <0.008"* 䖃 䖃
DCET 32.50.5 MFL JRP DCET11T302MFL-JRP <0.008"* 䖃 䖃

JSP DCET 21.5U MFN-JSP DCET0702008MFN-JSP <0.0031"* 䖃 䖃

DCET 21.50 MFN-JSP DCET070201MFN-JSP <0.004"* 䖃 䖃
DCET 21.50.4 MFN-JSP DCET0702018MFN-JSP <0.007"* 䖃 䖃
DCET 21.50.5 MFN-JSP DCET070202MFN-JSP <0.008"* 䖃 䖃
DCET 32.50.4 MFN-JSP DCET11T3008MFN-JSP <0.0031"* 䖃 䖃
DCET 32.50 MFN-JSP DCET11T301MFN-JSP <0.004"* 䖃 䖃 D
DCET 32.50.4 MFN-JSP DCET11T3018MFN-JSP <0.007"* 䖃 䖃
DCET 32.50.5 MFN-JSP DCET11T302MFN-JSP <0.008"* 䖃 䖃

J10 DCGT 21.5VFR J10 DCGT070200FR-J10 0.0012" 䖃 䖃 䖃

DCGT 21.5VFL J10 DCGT070200FL-J10 0.0012" 䖃 䖃 䖃
DCGT 21.50FR J10 DCGT070201FR-J10 0.004" 䖃 䖃 䖃 䖃
DCGT 21.50FL J10 DCGT070201FL-J10 0.004" 䖃 䖃 䖃 䖃
DCGT 21.50.5FR J10 DCGT070202FR-J10 0.008" 䖃 䖃 䖃 䖃
DCGT 21.50.5FL J10 DCGT070202FL-J10 0.008" 䖃 䖃 䖃 䖃
DCGT 21.51 FR J10 DCGT070204FR-J10 0.016" 䖃
DCGT 21.51 FL J10 DCGT070204FL-J10 0.016" 䖃
DCGT 32.5VFR J10 DCGT11T300FR-J10 0.0012" 䖃 䖃 䖃
DCGT 32.5VFL J10 DCGT11T300FL-J10 0.0012" 䖃 䖃 䖃
DCGT 32.50FR J10 DCGT11T301FR-J10 0.004" 䖃 䖃 䖃 䖃
DCGT 32.50FL J10 DCGT11T301FL-J10 0.004" 䖃 䖃 䖃 䖃
DCGT 32.50.5FR J10 DCGT11T302FR-J10 0.008" 䖃 䖃 䖃 䖃
DCGT 32.50.5FL J10 DCGT11T302FL-J10 0.008" 䖃 䖃 䖃 䖃
On small lathes

J10 DCGT 21.50.5R J10 DCGT070202R-J10 0.008" 䖃

(Honed edge)

DCGT 32.50.5R J10 DCGT11T302R-J10 0.008" 䖃

* Corner radius has minus tolerance. 䖃㻌: Line up

Note: See page B051 for chipbreaker descriptions.
Tungaloy B121
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel L CL
D O U B LE -SI D ED M Stainless L CL
K Cast iron L
Rhombic, 55° N Non-ferrous
with hole S Superalloys C
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

AH725
SH725
Inch Metric
JRP DXGU 220-MFRE-JRP DXGU070301MFRE-JRP <0.004"* 䖃
(Sharp edge)

DXGU 220-MFLE-JRP DXGU070301MFLE-JRP <0.004"* 䖃

Positive

Finishing

DXGU 220.5-MFRE-JRP DXGU070302MFRE-JRP <0.008"* 䖃

DXGU 220.5-MFLE-JRP DXGU070302MFLE-JRP <0.008"* 䖃

䖃
Finishing (Low cutting Finishing to medium Finishing to medium
cutting (Sharp edge)

JTS DXGU 220-MFR-JTS DXGU070301MFR-JTS <0.004"*

DXGU 220-MFL-JTS DXGU070301MFL-JTS <0.004"* 䖃

DXGU 220.5-MFR-JTS DXGU070302MFR-JTS <0.008"* 䖃

DXGU 220.5-MFL-JTS DXGU070302MFL-JTS <0.008"* 䖃

JTS DXGU 220-MR-JTS DXGU070301MR-JTS <0.004"* 䖃

DXGU 220-ML-JTS DXGU070301ML-JTS <0.004"* 䖃
cutting

DXGU 220.5-MR-JTS DXGU070302MR-JTS <0.008"* 䖃

DXGU 220.5-ML-JTS DXGU070302ML-JTS <0.008"* 䖃

JSS DXGU 220-MFR-JSS DXGU070301MFR-JSS <0.004"* 䖃

force) (Sharp edge)

DXGU 220-MFL-JSS DXGU070301MFL-JSS <0.004"* 䖃

DXGU 220.5-MFR-JSS DXGU070302MFR-JSS <0.008"* 䖃

DXGU 220.5-MFL-JSS DXGU070302MFL-JSS <0.008"* 䖃

D
* Corner radius has minus tolerance.
䖃㻌: Line up

Reference pages
External toolholders → B192 -
Internal toolholders → B288, B289

B122 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel L CL CL

Insert
DOU B LE-S I D ED M Stainless L
K Cast iron L CL CL C
Rhombic, 55° N Non-ferrous C
with hole S Superalloys C C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
Inch Metric
(Low cutting force)

JSS DXGU 220 MR-JSS DXGU070301MR-JSS <0.004"* 䖃

DXGU 220 ML-JSS DXGU070301ML-JSS <0.004"* 䖃

Positive
Finishing

DXGU 220.5 MR-JSS DXGU070302MR-JSS <0.008"* 䖃

DXGU 220.5 ML-JSS DXGU070302ML-JSS <0.008"* 䖃

TS DXGU 220.5 R-TS DXGU070302R-TS 0.008" 䖃 䖃 䖃 䖃

Finishing to medium

DXGU 220.5 L-TS DXGU070302L-TS 0.008" 䖃 䖃 䖃 䖃

DXGU 221 R-TS DXGU070304R-TS 0.016" 䖃 䖃 䖃 䖃

cutting

DXGU 221 L-TS DXGU070304L-TS 0.016" 䖃 䖃 䖃 䖃

DXGU 222 R-TS DXGU070308R-TS 0.031" 䖃 䖃 䖃 䖃

DXGU 222 L-TS DXGU070308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force)

SS DXGU 220.5 R-SS DXGU070302R-SS 0.008" 䖃 䖃 䖃 䖃

DXGU 220.5 L-SS DXGU070302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

DXGU 221 R-SS DXGU070304R-SS 0.016" 䖃 䖃 䖃 䖃

DXGU 221 L-SS DXGU070304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

Reference pages
External toolholders → B192 -
Internal toolholders → B288, B289

Tungaloy B123
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel C CL CL CL CL C L
M Stainless C CL CL C L
Rhombic, 75° K Cast iron C CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

SH730
SH725
GH110

UX30
TH10
Inch Metric
W08 EPGT 4.51.8 R-W08 EPGT03X100R-W08 0.0012" 䖃 䖃

EPGT 4.51.8 L-W08 EPGT03X100L-W08 0.0012" 䖃 䖃

Positive

EPGT 4.51.80 R-W08 EPGT03X101R-W08 0.004" 䖃 䖃

EPGT 4.51.80 L-W08 EPGT03X101L-W08 0.004" 䖃 䖃

EPGT 4.51.80.5 R-W08 EPGT03X102R-W08 0.008" 䖃 䖃

EPGT 4.51.80.5 L-W08 EPGT03X102L-W08 0.008" 䖃 䖃

EPGT 4.51.81 R-W08 EPGT03X104R-W08 0.016" 䖃 䖃

EPGT 4.51.81 L-W08 EPGT03X104L-W08 0.016" 䖃 䖃

Finishing

EPGT 52 R-W08 EPGT040100R-W08 0.0012" 䖃 䖃

EPGT 52 L-W08 EPGT040100L-W08 0.0012" 䖃 䖃 䖃 䖃

EPGT 520 R-W08 EPGT040101R-W08 0.004" 䖃 䖃

EPGT 520 L-W08 EPGT040101L-W08 0.004" 䖃 䖃

EPGT 520.5 R-W08 EPGT040102R-W08 0.008" 䖃 䖃 䖃 䖃

EPGT 520.5 L-W08 EPGT040102L-W08 0.008" 䖃 䖃 䖃 䖃 䖃 䖃

EPGT 521 R-W08 EPGT040104R-W08 0.016" 䖃 䖃 䖃 䖃

EPGT 521 L-W08 EPGT040104L-W08 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

W08 EPGT 4.51.8 FR-W08 EPGT03X100FL-W08 0.0012" 䖃

EPGT 4.51.8 FL-W08 EPGT03X100FR-W08 0.0012" 䖃

EPGT 4.51.80 FR-W08 EPGT03X101FL-W08 0.004" 䖃

EPGT 4.51.80 FL-W08 EPGT03X101FR-W08 0.004" 䖃

E EPGT 4.51.80.5 FR-W08 EPGT03X102FL-W08 0.008" 䖃

EPGT 4.51.80.5 FL-W08 EPGT03X102FR-W08 0.008" 䖃

Finishing (Sharp edge)

EPGT 4.51.81 FR-W08 EPGT03X104FL-W08 0.016" 䖃

EPGT 4.51.81 FL-W08 EPGT03X104FR-W08 0.016" 䖃

EPGT 52 FR-W08 EPGT040100FL-W08 0.0012" 䖃

EPGT 52 FL-W08 EPGT040100FR-W08 0.0012" 䖃

EPGT 520 FR-W08 EPGT040101FL-W08 0.004" 䖃

EPGT 520 FL-W08 EPGT040101FR-W08 0.004" 䖃

EPGT 520.5 FR-W08 EPGT040102FL-W08 0.008" 䖃

EPGT 520.5 FL-W08 EPGT040102FR-W08 0.008" 䖃

EPGT 521 FR-W08 EPGT040104FL-W08 0.016" 䖃

EPGT 521 FL-W08 EPGT040104FR-W08 0.016" 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B302 -

B124 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL CL

Insert
M Stainless CL CL CL
Rhombic, 75° K Cast iron
with hole N Non-ferrous
Positive 11° S Superalloys CL
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

SH730
SH725

J740
Inch Metric
JS EPGT 4.51.80 JS EPGT03X101-JS 0.004" 䖃
For internal turning

EPGT 4.51.80.5 JS EPGT03X102-JS 0.008" 䖃

Positive
on small lathes

EPGT 4.51.81 JS EPGT03X104-JS 0.016" 䖃

EPGT 520 JS EPGT040101-JS 0.004" 䖃

EPGT 520.5 JS EPGT040102-JS 0.008" 䖃

EPGT 521 JS EPGT040104-JS 0.016" 䖃

JS EPGT 4.51.80 F-JS EPGT03X101F-JS 0.004" 䖃

small lathes (Sharp edge)
For internal turning on

EPGT 4.51.80.5 F-JS EPGT03X102F-JS 0.008" 䖃

EPGT 4.51.81 F-JS EPGT03X104F-JS 0.016" 䖃

EPGT 520 F-JS EPGT040101F-JS 0.004" 䖃

EPGT 520.5 F-JS EPGT040102F-JS 0.008" 䖃

EPGT 521 F-JS EPGT040104F-JS 0.016" 䖃

J08 EPGT 52 L-J08 EPGT040100L-J08 0.0012" 䖃 䖃

EPGT 520.5 L-J08 EPGT040102L-J08 䖃 䖃

Finishing

0.008"

EPGT 521 L-J08 EPGT040104L-J08 0.016" 䖃 䖃

J08 EPGT 52 FL-J08 EPGT040100FL-J08 0.0012" 䖃

(Sharp edge)

EPGT 520.5 FL-J08 EPGT040102FL-J08 0.008" 䖃

Finishing

EPGT 521 FL-J08 EPGT040104FL-J08 0.016" 䖃 E

䖃㻌: Line up

Reference pages
Internal toolholders → B302 -

Tungaloy B125
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH CL
M Stainless CL C L
Round, K Cast iron CL L CL C
with hole N Non-ferrous C
Positive 7° S Superalloys CL C L L C
H Hard materials
Coated Uncoated
Application

Corner
radius

AH8005
AH8015
Chipbreaker Designation

KS05F
AH120

AH905
T9125
T9115

T5115
Inch Metric
RS - RCMT10T3M0-RS - 䖃 䖃 䖃 䖃 䖃

- RCMT1204M0-RS - 䖃 䖃 䖃 䖃 䖃 䖃
Positive

- RCMT1606M0-RS - 䖃 䖃 䖃

- RCMT2006M0-RS - 䖃
Finishing to medium cutting

- RCMT2507M0-RS - 䖃

CM - RCMT0502M0-CM - 䖃

- RCMT0602M0-CM - 䖃

- RCMT0803M0-CM - 䖃

AL - RCGT0602M0-AL - 䖃

- RCGT0803M0-AL - 䖃

- RCGT1003M0-AL - 䖃

䖃㻌: Line up

Reference pages
External toolholders → B245 -

B126 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH CL C

Insert
M Stainless C L C
Round, K Cast iron CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C L L
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

AH8005

NS9530
AH8015
Chipbreaker Designation

AH905
T9125
T9115

TH10
Inch Metric
61 - RCMT0502M0-61 - 䖃 䖃 䖃 䖃

- RCMT0602M0-61 - 䖃 䖃 䖃 䖃

Positive
- RCMT0803M0-61 - 䖃 䖃 䖃 䖃
Heavy cutting

61 - RCMM1003M0-61 - 䖃 䖃 䖃 䖃 䖃 䖃 䖃

- RCMM1204M0-61 - 䖃 䖃 䖃 䖃 䖃 䖃 䖃

- RCMM1606M0-61 - 䖃 䖃 䖃

- RCMM2006M0-61 - 䖃 䖃

- RCMM2507M0-61 - 䖃

Designation 0502M0 0602M0 0803M0 1003M0 10T3M0 1204M0 1606M0 2006M0 2507M0
ød1 (in)

RC*T 0.098 0.110 0.134 0.173 0.173 0.173 0.217 0.256 0.299
RCMM - - - 0.142 - 0.165 0.205 0.256 0.283

P Steel C
M Stainless C R
Special Round K Cast iron C LH
Insert N Non-ferrous C LH
S Superalloys LH
H Hard materials
Uncoated
Application

Corner
radius

Chipbreaker Designation
KS20
TH10

Inch Metric
- - RT05 - 䖃
Medium cutting

- RT06 - 䖃 䖃

- RT08 - 䖃

䖃㻌: Line up
Reference pages
RC... : External toolholders → B245 -
RT... : External toolholders → B268

Tungaloy B127
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel
M Stainless
Round, K Cast iron
without hole N Non-ferrous
S Superalloys
Positive 7°
H Hard materials C
Ceramics
Application

Corner
radius
Chipbreaker Designation

LX11
Inch Metric
- - RCGX090800 - 䖃
Medium cutting

- RCGX120800 - 䖃
Positive

䖃㻌: Line up

B128 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L CL CL

Insert
M Stainless C L L H CL L
Square, 90° K Cast iron CL CL L CL L CL CL
with hole N Non-ferrous
Positive 7° S Superalloys CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115

T5115
T515
Inch Metric
PS SCMT 32.51 PS SCMT09T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing to medium cutting

SCMT 32.52 PS SCMT09T308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive
SCMT 431 PS SCMT120404-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SCMT 432 PS SCMT120408-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

23 SCMT 32.50.5-23 SCMT09T302-23 0.008" 䖃

SCMT 32.52-23 SCMT09T308-23 0.031" 䖃 䖃

SCMT 432-23 SCMT120408-23 0.031" 䖃 䖃 䖃

24 SCMT 2.51.51-24 SCMT070204-24 0.016" 䖃 䖃

SCMT 32.50.5-24 SCMT09T302-24 0.008" 䖃

SCMT 32.51-24 SCMT09T304-24 0.016" 䖃 䖃

SCMT 32.52-24 SCMT09T308-24 0.031" 䖃 䖃 䖃 䖃

Medium cutting

SCMT 431-24 SCMT120404-24 0.016" 䖃 䖃

SCMT 432-24 SCMT120408-24 0.031" 䖃 䖃 䖃 䖃

PM SCMT 32.51 PM SCMT09T304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SCMT 32.52 PM SCMT09T308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SCMT 432 PM SCMT120408-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SCMT 433 PM SCMT120412-PM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CM SCMT 32.51 CM SCMT09T304-CM 0.016" 䖃 䖃

Finishing to medium

SCMT 32.52 CM SCMT09T308-CM 0.031" 䖃 䖃

cutting

SCMT 32.53 CM SCMT09T312-CM 0.047" 䖃

S
SCMT 431 CM SCMT120404-CM 0.016" 䖃 䖃

SCMT 432 CM SCMT120408-CM 0.031" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B266

Tungaloy B129
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L H LH H CL L CL CL C
M Stainless C L L H CL L C
Square, 90° K Cast iron CL CL L CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys CL C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115

TH10
Inch Metric
PS SPMT321 PS SPMT090304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Finishing to medium cutting

SPMT322 PS SPMT090308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive

SPMT431 PS SPMT120404-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

SPMT432 PS SPMT120408-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

23 SPMT321-23 SPMT090304-23 0.016" 䖃 䖃

SPMT322-23 SPMT090308-23 0.031" 䖃 䖃

Medium cutting

24 SPMT 321-24 SPMT090304-24 0.016" 䖃 䖃

SPMT 322-24 SPMT090308-24 0.031" 䖃 䖃 䖃

SPMT 431-24 SPMT120404-24 0.016" 䖃

SPMT 432-24 SPMT120408-24 0.031" 䖃 䖃

W15 SPGT 320.5L W15 SPGT090302L-W15 0.008" 䖃

SPGT 321L W15 SPGT090304L-W15 0.016" 䖃 䖃

SPGT 322R W15 SPGT090308R-W15 0.031" 䖃

SPGT 322L W15 SPGT090308L-W15 0.031" 䖃 䖃

Finishing

W20 SPGT431L W20 SPGT120404L-W20 0.016" 䖃

S
䖃㻌: Line up

Reference pages
External toolholders → B258 - Internal toolholders → B307, B335

B130 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL C

Insert
M Stainless C
Square, 90° K Cast iron CL L CL C
with hole N Non-ferrous C
Positive 11° S Superalloys
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

T5115

TH10
T515
Inch Metric
CM SPMT 321 CM SPMT090304-CM 0.016" 䖃

SPMT 322 CM SPMT090308-CM 0.031" 䖃

Positive
SPMT 431 CM SPMT120404-CM 0.016" 䖃 䖃

SPMT 432 CM SPMT120408-CM 0.031" 䖃 䖃

- SPGM 321L SPGM090304L 0.016" 䖃

(Tungaloy's SPGM 421L SPGM120304L 0.016" 䖃
standard hole)
SPGM 422 L SPGM120308L 0.031" 䖃
Finishing to medium cutting

- SPMW 321 SPMW090304 0.016" 䖃

SPMW 322 SPMW090308 0.031" 䖃

SPMW 431 SPMW120404 0.016" 䖃

SPMW 432 SPMW120408 0.031" 䖃

- SPGW 320.5 SPGW090302 0.008" 䖃

SPGW 321 SPGW090304 0.016" 䖃

SPGW 431 SPGW120404 0.016" 䖃

- SPGA 321 SPGA090304 0.016" 䖃

(Tungaloy's
standard hole)

S
䖃㻌: Line up

Reference pages
External toolholders → B258 - Internal toolholders → B307, B335

Tungaloy B131
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel LH CL CL CL CL L C C
M Stainless CL CL CL C C
Square, 90° K Cast iron L CL CL CL CL L C
without hole N Non-ferrous C
Positive 11° S Superalloys CL
H Hard materials C
Coated Cermet Uncoated Ceramics
Application

Corner
radius

NS9530
Chipbreaker Designation

AH330
AH120

NS740
T9125

T3130
T5115

UX30
TH10

LX11
Inch Metric
23 SPMR 321-23 SPMR090304-23 0.016" 䖃

SPMR 322-23 SPMR090308-23 0.031" 䖃 䖃

Positive

SPMR 421-23 SPMR120304-23 0.016" 䖃 䖃

SPMR 422-23 SPMR120308-23 0.031" 䖃 䖃

CM SPMR 321 CM SPMR090304-CM 0.016" 䖃

SPMR 322 CM SPMR090308-CM 0.031" 䖃

SPMR 421 CM SPMR120304-CM 0.016" 䖃

SPMR 422 CM SPMR120308-CM 0.031" 䖃

SPMR 423 CM SPMR120312-CM 0.047" 䖃

- SPGR 321L SPGR090304L 0.016" 䖃

Finishing to medium cutting

- SPG 321 SPGN090304 0.016" 䖃 䖃

SPG 322 SPGN090308 0.031" 䖃 䖃

SPG 421 SPGN120304 0.016" 䖃 䖃

SPG 422 SPGN120308 0.031" 䖃 䖃 䖃

SPG 423 SPGN120312 0.047" 䖃 䖃 䖃

SPG 432 SPGN120408 0.031" 䖃 䖃

- SPU 321 SPMN090304 0.016" 䖃

SPU 322 SPMN090308 0.031" 䖃 䖃

S
SPU 421 SPMN120304 0.016" 䖃

SPU 422 SPMN120308 0.031" 䖃 䖃 䖃 䖃

SPU 423 SPMN120312 0.047" 䖃 䖃 䖃 䖃

SPU 432 SPMN120408 0.031" 䖃 䖃 䖃 䖃 䖃

SPU 433 SPMN120412 0.047" 䖃 䖃

SPU 643 SPMN190412 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B258 - Internal toolholders → B307, B335

B132 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L CL CL CL CL CL C

Insert
M Stainless L CL CL C
Triangular, 60° K Cast iron CL L CL CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

NS520
AH725
SH725
T9125
T9115

TH10
J740
Inch Metric
01 TCGT731-01 TCGT090204-01 0.016" 䖃 䖃
Precision finishing

TCGT21.50.5-01 TCGT110202-01 0.008" 䖃

Positive
TCGT21.51-01 TCGT110204-01 0.016" 䖃 䖃 䖃 䖃

TCGT21.52-01 TCGT110208-01 0.031" 䖃

TCGT32.51-01 TCGT16T304-01 0.016" 䖃

TCGT32.52-01 TCGT16T308-01 0.031" 䖃 䖃

Precision finishing

01 TCGT 21.50.5 F-01 TCGT110202F-01 0.008" 䖃

(Sharp edge)

PSF TCMT 730.5 PSF TCMT090202-PSF 0.008" 䖃

TCMT 731 PSF TCMT090204-PSF 0.016" 䖃 䖃 䖃

TCMT 21.50.5 PSF TCMT110202-PSF 0.008" 䖃

Finishing

TCMT 21.51 PSF TCMT110204-PSF 0.016" 䖃 䖃 䖃

TCMT 220.5 PSF TCMT110302-PSF 0.008" 䖃

TCMT 221 PSF TCMT110304-PSF 0.016" 䖃 䖃 䖃

TCMT 32.51 PSF TCMT16T304-PSF 0.016" 䖃 䖃 䖃

PSS TCMT 731 PSS TCMT090204-PSS 0.016" 䖃 䖃 䖃

TCMT 732 PSS TCMT090208-PSS 0.031" 䖃 䖃 䖃

Finishing to light cutting

TCMT 21.51 PSS TCMT110204-PSS 0.016" 䖃 䖃 䖃

TCMT 21.52 PSS TCMT110208-PSS 0.031" 䖃 䖃 䖃

TCMT 221 PSS TCMT110304-PSS 0.016" 䖃 䖃 䖃

TCMT 222 PSS TCMT110308-PSS 0.031" 䖃 䖃 䖃

TCMT 32.51 PSS TCMT16T304-PSS 0.016" 䖃 䖃 䖃

T
TCMT 32.52 PSS TCMT16T308-PSS 0.031" 䖃 䖃 䖃

TCMT 32.53 PSS TCMT16T312-PSS 0.047" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B262 Internal toolholders → B308
J series toolholders → B370

Tungaloy B133
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L H LH H L L CL CL C
M Stainless C L L H L L C
Triangular, 60° K Cast iron CL L L CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH730
AH630
AH645
AH725
T9125

T6130
T6120
T9115

TH10
Inch Metric
PS TCMT 731 PS TCMT090204-PS 0.016" 䖃

TCMT 732 PS TCMT090208-PS 0.031" 䖃

Positive

TCMT 21.50.5 PS TCMT110202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 21.51 PS TCMT110204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 21.52 PS TCMT110208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

TCMT 220.5 PS TCMT110302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 221 PS TCMT110304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 222 PS TCMT110308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 32.50 PS TCMT16T302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 32.51 PS TCMT16T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 32.52 PS TCMT16T308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

23 TCMT 731-23 TCMT090204-23 0.016" 䖃 䖃

TCMT 21.51-23 TCMT110204-23 0.016" 䖃

TCMT 32.51-23 TCMT16T304-23 0.016" 䖃

TCMT 32.52-23 TCMT16T308-23 0.031" 䖃

24 TCMT 730.5-24 TCMT090202-24 0.008" 䖃

TCMT 731-24 TCMT090204-24 0.016" 䖃 䖃 䖃

Medium cutting

TCMT 21.50.5-24 TCMT110202-24 0.008" 䖃

TCMT 21.51-24 TCMT110204-24 0.016" 䖃 䖃 䖃

TCMT 21.52-24 TCMT110208-24 0.031" 䖃

TCMT 32.51-24 TCMT16T304-24 0.016" 䖃 䖃 䖃

TCMT 32.52-24 TCMT16T308-24 0.031" 䖃 䖃 䖃

W15 TCGT 32.50.5L W15 TCGT16T302L-W15 0.008" 䖃

TCGT 32.51L W15 TCGT16T304L-W15 0.016" 䖃 䖃

Finishing

T
TCGT 32.52L W15 TCGT16T308L-W15 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B263 Internal toolholders → B308
J series toolholders → B370

B134 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H L CL

Insert
M Stainless C L L H L
Triangular, 60° K Cast iron CL CL L L CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

AH630
AH645

KS05F
AH725
T9125

T6130
T6120
T9115

T5115
T515
Inch Metric
PM TCMT 21.50.5 PM TCMT110202-PM 0.008" 䖃 䖃 䖃 䖃 䖃

TCMT 21.51 PM TCMT110204-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive
TCMT 21.52 PM TCMT110208-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
Medium cutting

TCMT 220.5 PM TCMT110302-PM 0.008" 䖃 䖃 䖃 䖃

TCMT 221 PM TCMT110304-PM 0.016" 䖃 䖃 䖃 䖃

TCMT 222 PM TCMT110308-PM 0.031" 䖃 䖃 䖃 䖃

TCMT 32.51 PM TCMT16T304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 32.52 PM TCMT16T308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TCMT 32.53 PM TCMT16T312-PM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

CM TCMT 731 CM TCMT090204-CM 0.016" 䖃

TCMT 732 CM TCMT090208-CM 0.031" 䖃

TCMT 21.51 CM TCMT110204-CM 0.016" 䖃

TCMT 21.52 CM TCMT110208-CM 0.031" 䖃

TCMT 221 CM TCMT110304-CM 0.016" 䖃

TCMT 222 CM TCMT110308-CM 0.031" 䖃

TCM T32.51 CM TCMT16T304-CM 0.016" 䖃 䖃

Finishing to medium cutting

TCMT 32.52 CM TCMT16T308-CM 0.031" 䖃 䖃

TCMT 32.53 CM TCMT16T312-CM 0.047" 䖃 䖃

SS TCGT 21.50.5 SS TCGT110202-SS 0.008" 䖃

TCGT 21.51 SS TCGT110204-SS 0.016" 䖃

TCGT 21.52 SS TCGT110208-SS 0.031" 䖃

TCGT 32.51 SS TCGT16T304-SS 0.016" 䖃

AL TCGT 21.50.5 AL TCGT110202-AL 0.008" 䖃

T
TCGT 21.51 AL TCGT110204-AL 0.016" 䖃

TCGT 32.50.5 AL TCGT16T302-AL 0.008" 䖃

TCGT 32.51 AL TCGT16T304-AL 0.016" 䖃

TCGT 32.52 AL TCGT16T308-AL 0.031" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B263 Internal toolholders → B308
J series toolholders → B370

Tungaloy B135
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel L CL CL CL CL C
M Stainless L CL CL CL C
Triangular, 60° K Cast iron L CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C CL
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

AH725

SH730
SH725

TH10
J740
Inch Metric
- TCGT 630 R TCGT080102R 0.008" 䖃 䖃
Finishing
Positive

JS TCGT 21.50.VFN JS TCGT110200FN-JS 0.0012" 䖃 䖃

For external turning
on small lathes

TCGT 21.50FN JS TCGT110201FN-JS 0.004" 䖃 䖃

(Sharp edge)

TCGT 21.50.5FN JS TCGT110202FN-JS 0.008" 䖃 䖃

TCGT 21.51FN JS TCGT110204FN-JS 0.016" 䖃 䖃

JS TCGT 21.50N JS TCGT110201N-JS 0.004" 䖃

On small lathes
(Honed edge)

TCGT 21.50.5N JS TCGT110202N-JS 0.008" 䖃

TCGT 21.51N JS TCGT110204N-JS 0.016" 䖃

J08 TCGT 63V FR-J08 TCGT080200FR-J08 0.0012" 䖃 䖃 䖃

For external turning on small

TCGT 63V FL-J08 TCGT080200FL-J08 0.0012" 䖃 䖃 䖃

lathes (Sharp edge)

TCGT 63.50FR-J08 TCGT080201FR-J08 0.004" 䖃 䖃 䖃

TCGT 63.50FL-J08 TCGT080201FL-J08 0.004" 䖃 䖃 䖃

TCGT 630.5FR-J08 TCGT080202FR-J08 0.008" 䖃 䖃 䖃

TCGT 630.5FR-J08 TCGT080202FL-J08 0.008" 䖃 䖃 䖃

TCGT 631FR-J08 TCGT080204FR-J08 0.016" 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B308
J series toolholders → B370

B136 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL CL CL C

Insert
M Stainless CL CL C
Triangular, 60° K Cast iron CL CL C
with hole N Non-ferrous C
Positive 7° S Superalloys
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
Chipbreaker Designation

SH725

J9530

TH10
J740
Inch Metric
J10 TCGT 21.5 VFR-J10 TCGT110200FR-J10 0.0012" 䖃 䖃 䖃

TCGT 21.5 VFL-J10 TCGT110200FL-J10 0.0012" 䖃 䖃 䖃

Positive
For external turning on small lathes

TCGT 21.50 FR-J10 TCGT110201FR-J10 0.004" 䖃 䖃 䖃

TCGT 21.50 FL-J10 TCGT110201FL-J10 0.004" 䖃 䖃 䖃

TCGT 21.50.5 FR-J10 TCGT110202FR-J10 0.008" 䖃 䖃 䖃 䖃

(Sharp edge)

TCGT 21.50.5 FL-J10 TCGT110202FL-J10 0.008" 䖃 䖃 䖃 䖃

TCGT 21.51 FR-J10 TCGT110204FR-J10 0.016" 䖃

TCGT 22 VFR-J10 TCGT110300FR-J10 0.0012" 䖃 䖃 䖃

TCGT 22 VFL-J10 TCGT110300FL-J10 0.0012" 䖃 䖃 䖃

TCGT 220 FR-J10 TCGT110301FR-J10 0.004" 䖃 䖃 䖃

TCGT 220 FL-J10 TCGT110301FL-J10 0.004" 䖃 䖃 䖃

TCGT 220.5 FR-J10 TCGT110302FR-J10 0.008" 䖃 䖃 䖃 䖃

TCGT 220.5 FL-J10 TCGT110302FL-J10 0.008" 䖃 䖃 䖃 䖃

J10 TCGT 220.5 R-J10 TCGT110302R-J10 0.008" 䖃

On small lathes
(Honed edge)

TCGT 220.5 L-J10 TCGT110302L-J10 0.008" 䖃

䖃㻌: Line up

Reference pages
Internal toolholders → B308
J series toolholders → B370

Tungaloy B137
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L L CL CL CL CL C
M Stainless L L C
Triangular, 60° K Cast iron CL L L CL CL CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys C
H Hard materials
Coated Coated cermet Cermet Uncoated
Application

Corner
radius

GT9530

NS9530
Chipbreaker Designation

GH730
AH725

GT720

NS520
T9115
T9125

TH10
Inch Metric
01 TPGT 730.5-01 TPGT090202-01 0.008" 䖃 䖃

TPGT 731-01 TPGT090204-01 0.016" 䖃 䖃 䖃 䖃

Positive

TPGT21.50.5-01 TPGT110202-01 0.008" 䖃 䖃

Precision finishing

TPGT 21.51-01 TPGT110204-01 0.016" 䖃 䖃 䖃 䖃

TPGT 21.52-01 TPGT110208-01 0.031" 䖃

TPGT 2.520.5-01 TPGT130302-01 0.008" 䖃 䖃

TPGT 2.521-01 TPGT130304-01 0.016" 䖃 䖃 䖃 䖃

TPGT 2.522-01 TPGT130308-01 0.031" 䖃 䖃

TPGT 32.51-01 TPGT16T304-01 0.016" 䖃 䖃 䖃 䖃

TPGT 32.52-01 TPGT16T308-01 0.031" 䖃 䖃 䖃

PSF TPMT 730.5 PSF TPMT090202-PSF 0.008" 䖃 䖃

TPMT 731 PSF TPMT090204-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

TPMT21.50.5 PSF TPMT110202-PSF 0.008" 䖃 䖃 䖃

TPMT 21.51 PSF TPMT110204-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

TPMT 220.5 PSF TPMT110302-PSF 0.008" 䖃 䖃

TPMT 221 PSF TPMT110304-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

TPMT 2.521 PSF TPMT130304-PSF 0.016" 䖃 䖃 䖃

TPMT 32.51 PSF TPMT16T304-PSF 0.016" 䖃 䖃 䖃 䖃

Finishing

PF TPMT 21.51 PF TPMT110204-PF 0.016" 䖃 䖃 䖃

TPMT 21.52 PF TPMT110208-PF 0.031" 䖃 䖃

TPMT 220.5 PF TPMT110302-PF 0.008" 䖃 䖃

TPMT 221 PF TPMT110304-PF 0.016" 䖃 䖃 䖃

TPMT 2.521 PF TPMT130304-PF 0.016" 䖃 䖃

TPMT 2.522 PF TPMT130308-PF 0.031" 䖃

TPMT 32.51 PF TPMT16T304-PF 0.016" 䖃 䖃

T

䖃㻌: Line up

Reference pages
Mounting hole specifications → B143
External toolholders → B258 - B260 Internal toolholders → B309 -

B138 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L L CL CL

Insert
M Stainless C L L H CL L L
Triangular, 60° K Cast iron CL CL L L CL CL
with hole N Non-ferrous
Positive 11° S Superalloys CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH730
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115
Inch Metric
PSS TPMT 731 PSS TPMT090204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 732 PSS TPMT090208-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Positive
Finishing to light cutting

TPMT 21.51 PSS TPMT110204-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 21.52 PSS TPMT110208-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 221 PSS TPMT110304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 222 PSS TPMT110308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.521 PSS TPMT130304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.522 PSS TPMT130308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.51 PSS TPMT16T304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.52 PSS TPMT16T308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

PS TPMT 730.5 PS TPMT090202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 731 PS TPMT090204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 732 PS TPMT090208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 21.50.5 PS TPMT110202-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 21.51 PS TPMT110204-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 21.52 PS TPMT110208-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 221 PS TPMT110304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

TPMT 222 PS TPMT110308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.520.5 PS TPMT130302-PS 0.008" 䖃 䖃 䖃 䖃 䖃

TPMT 2.521 PS TPMT130304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.522 PS TPMT130308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.51 PS TPMT16T304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.52 PS TPMT16T308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

23 TPMT 730.5-23 TPMT090202-23 0.008" 䖃

TPMT 731-23 TPMT090204-23 0.016" 䖃 䖃

T
TPMT 21.51-23 TPMT110204-23 0.016" 䖃 䖃

TPMT 2.521-23 TPMT130304-23 0.016" 䖃 䖃

TPMT 2.522-23 TPMT130308-23 0.031" 䖃 䖃

TPMT 32.51-23 TPMT16T304-23 0.016" 䖃

TPMT 32.52-23 TPMT16T308-23 0.031" 䖃 䖃

䖃㻌: Line up

Reference pages
Mounting hole specifications → B143
External toolholders → B258 - B260 Internal toolholders → B309 -

Tungaloy B139
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel LH C CL CL CL CL CL C L
M Stainless C CL CL CL C L
Triangular, 60° K Cast iron C CL CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys C CL CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

SH730
SH725

AH120
GH110
T9125

UX30
TH10
Inch Metric
24 TPMT 731-24 TPMT090204-24 0.016" 䖃 䖃

TPMT 21.51-24 TPMT110204-24 0.016" 䖃 䖃

Positive

Medium cutting

TPMT 21.52-24 TPMT110208-24 0.031" 䖃 䖃 䖃

TPMT 2.521-24 TPMT130304-24 0.016" 䖃 䖃

TPMT 2.522-24 TPMT130308-24 0.031" 䖃 䖃

TPMT 32.51-24 TPMT16T304-24 0.016" 䖃 䖃

TPMT 32.52-24 TPMT16T308-24 0.031" 䖃 䖃

W08 TPGT 5.52 R-W08 TPGT070100R-W08 0.0012" 䖃 䖃

TPGT 5.52 L-W08 TPGT070100L-W08 0.0012" 䖃 䖃

TPGT 5.520 R-W08 TPGT070101R-W08 0.004" 䖃 䖃

TPGT 5.520 L-W08 TPGT070101L-W08 0.004" 䖃 䖃

TPGT 5.520.5 R-W08 TPGT070102R-W08 0.008" 䖃 䖃

Finishing

TPGT 5.520.5 L-W08 TPGT070102L-W08 0.008" 䖃 䖃

TPGT 5.521 R-W08 TPGT070104R-W08 0.016" 䖃 䖃

TPGT 5.521 L-W08 TPGT070104L-W08 0.016" 䖃 䖃

TPGT 63VL-W08 TPGT080200L-W08 0.0012" 䖃 䖃

TPGT 630.5L-W08 TPGT080202L-W08 0.008" 䖃 䖃 䖃 䖃 䖃

TPGT 631L-W08 TPGT080204L-W08 0.016" 䖃 䖃 䖃 䖃 䖃

W08 TPGT 5.52 FL-W08 TPGT070100FL-W08 0.0012" 䖃

TPGT 5.52 FR-W08 TPGT070100FR-W08 0.0012" 䖃

Finishing (Sharp edge)

TPGT 5.520 FL-W08 TPGT070101FL-W08 0.004" 䖃

TPGT 5.520 FR-W08 TPGT070101FR-W08 0.004" 䖃

TPGT 5.520.5 FL-W08 TPGT070102FL-W08 0.008" 䖃

TPGT 5.520.5 FR-W08 TPGT070102FR-W08 0.008" 䖃

TPGT 5.521 FL-W08 TPGT070104FL-W08 0.016" 䖃

T
TPGT 5.521 FR-W08 TPGT070104FR-W08 0.016" 䖃

䖃㻌: Line up

Reference pages
Mounting hole specifications → B143
External toolholders → B258 - B260 Internal toolholders → B309 -

B140 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel C CL CL CL C L

Insert
M Stainless C CL C L
Triangular, 60° K Cast iron C CL CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH330
GH110

UX30
TH10
Inch Metric
W10 TPGH 630.5L W10 TPGH080202L-W10 0.008" 䖃 䖃

TPGH 631 L W10 TPGH080204L-W10 0.016" 䖃 䖃

Positive
TPGH 731 L W10 TPGH090204L-W10 0.016" 䖃 䖃

W13 TPGH 21.51L W13 TPGH110204L-W13 0.016" 䖃 䖃

TPGH 220.5L W13 TPGH110302L-W13 0.008" 䖃 䖃

TPGH 221.5L W13 TPGH110304L-W13 0.016" 䖃 䖃

W15 TPGT 730.5R W15 TPGT090202R-W15 0.008" 䖃

TPGT730.5L W15 TPGT090202L-W15 0.008" 䖃 䖃 䖃

TPGT 731R W15 TPGT090204R-W15 0.016" 䖃

TPGT 731L W15 TPGT090204L-W15 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TPGT 21.50.5R W15 TPGT110202R-W15 0.008" 䖃

TPGT 21.50.5L W15 TPGT110202L-W15 0.008" 䖃 䖃 䖃

Finishing

TPGT 21.51L-W15 TPGT110204L-W15 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TPGT 21.52R-W15 TPGT110208R-W15 0.031" 䖃

TPGT 21.52L-W15 TPGT110208L-W15 0.031" 䖃

TPGT 220.5R-W15 TPGT110302L-W15 0.008" 䖃

TPGT 221L-W15 TPGT110304R-W15 0.016" 䖃

TPGT 221L-W15 TPGT110304L-W15 0.016" 䖃

TPGT 222L-W15 TPGT110308L-W15 0.031" 䖃

TPGT 2.520.5R W15 TPGT130302R-W15 0.008" 䖃

TPGT 2.520.5L W15 TPGT130302L-W15 0.008" 䖃 䖃 䖃

TPGT 2.521R W15 TPGT130304R-W15 0.016" 䖃 䖃

TPGT 2.521L W15 TPGT130304L-W15 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

T
TPGT 2.522L W15 TPGT130308L-W15 0.031" 䖃 䖃

TPGT 32.50.5R W15 TPGT16T302R-W15 0.008" 䖃

TPGT 32.50.5L W15 TPGT16T302L-W15 0.008" 䖃 䖃 䖃

TPGT 32.51R W15 TPGT16T304R-W15 0.016" 䖃 䖃

TPGT 32.51L W15 TPGT16T304L-W15 0.016" 䖃 䖃 䖃 䖃 䖃 䖃

TPGT 32.52L W15 TPGT16T308L-W15 0.031" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
Mounting hole specifications → B143
External toolholders → B258 - B260 Internal toolholders → B309 -

Tungaloy B141
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH L H LH H CL L CL L CL CL
M Stainless C L L H CL L CL L
Triangular, 60° K Cast iron CL CL L CL L CL L CL CL
with hole N Non-ferrous
Positive 11° S Superalloys CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

GH330
GH730
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115

T5115
T515
Inch Metric
PM TPMT 731 PM TPMT090204-PM 0.016" 䖃 䖃 䖃 䖃 䖃

TPMT 732 PM TPMT090208-PM 0.031" 䖃 䖃 䖃 䖃 䖃

Positive

TPMT 21.51 PM TPMT110204-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 21.52 PM TPMT110208-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Medium cutting

TPMT 221 PM TPMT110304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 222 PM TPMT110308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.521 PM TPMT130304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 2.522 PM TPMT130308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.51 PM TPMT16T304-PM 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.52 PM TPMT16T308-PM 0.031" 䖃 䖃 䖃 䖃 䖃 䖃

TPMT 32.53 PM TPMT16T312-PM 0.047" 䖃 䖃 䖃 䖃 䖃 䖃

CM TPMT 731 CM TPMT090204-CM 0.016" 䖃

TPMT 732 CM TPMT090208-CM 0.031" 䖃

TPMT 21.51 CM TPMT110204-CM 0.016" 䖃

TPMT 21.52 CM TPMT110208-CM 0.031" 䖃

TPMT 221 CM TPMT110304-CM 0.016" 䖃

TPMT 222 CM TPMT110308-CM 0.031" 䖃

Finishing to medium cutting

TPMT 2.521 CM TPMT130304-CM 0.016" 䖃

TPMT 2.522 CM TPMT130308-CM 0.031" 䖃

TPMT 32.51 CM TPMT16T304-CM 0.016" 䖃 䖃

TPMT 32.52 CM TPMT16T308-CM 0.031" 䖃 䖃

TPMT 32.53 CM TPMT16T312-CM 0.047" 䖃 䖃

SS TPGT 21.50.5 SS TPGT110202-SS 0.008" 䖃

TPGT 21.51 SS TPGT110204-SS 0.016" 䖃 䖃

TPGT 21.52.5 SS TPGT130302-SS 0.008" 䖃

T
TPGT 2.520.5 SS TPGT130304-SS 0.016" 䖃 䖃

TPGT 32.51 SS TPGT16T304-SS 0.016" 䖃 䖃

䖃㻌: Line up

Reference pages
Mounting hole specifications → B143
External toolholders → B258 - B260 Internal toolholders → B309 -

B142 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL C L

Insert
M Stainless C L
Triangular, 60° K Cast iron L CL CL C
with hole N Non-ferrous C
Positive 11° S Superalloys
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

T5115

UX30
TH10
Inch Metric
H11 TPGH 220.5L H11 TPGH110302L-H11 0.008" 䖃 䖃

TPGH 221L H11 TPGH110304L-H11 0.016" 䖃 䖃

Positive
- TPGM 5.520.5 R TPGM070102R 0.008" 䖃

TPGM 5.520.5 L TPGM070102L 0.008" 䖃 䖃

TPGM 5.521 R TPGM070104R 0.016" 䖃

TPGM 5.521 L TPGM070104L 0.016" 䖃 䖃

TPGM 730.5R TPGM090202R 0.008" 䖃

TPGM 730.5L TPGM090202L 0.008" 䖃

TPGM 731L TPGM090204L 0.016" 䖃

TPGM 21.50.5R TPGM110202R 0.008" 䖃

TPGM 21.50.5L TPGM110202L 0.008" 䖃 䖃

Finishing to medium cutting

Tungaloy-
standard hole TPGM 21.51R TPGM110204R 0.016" 䖃
Not ISO TPGM 21.51L TPGM110204L 0.016" 䖃 䖃

TPGM 220.5R TPGM110302R 0.008" 䖃

TPGM 220.5L TPGM110302L 0.008" 䖃

TPGM...R/L TPGM 220.5L-2 TPGM110302L-2 0.008" 䖃

TPGM 221R TPGM110304R 0.016" 䖃

TPGM 221L TPGM110304L 0.016" 䖃 䖃

TPGM 221L-2 TPGM110304L-2 0.016" 䖃

TPGM 320.5L TPGM160302L 0.008" 䖃

TPGM 32.51R TPGM160304R 0.016" 䖃

TPGM 32.51L TPGM160304L 0.016" 䖃 䖃

TPGM 32.51L-2 TPGM160304L-2 0.016" 䖃

- TPMW 21.51 TPMW110204 0.016" 䖃 T

TPMW 21.52 TPMW110208 0.031" 䖃

TPMW 2.521 TPMW130304 0.016" 䖃

TPMW 2.522 TPMW130308 0.031" 䖃

TPMW 32.51 TPMW16T304 0.016" 䖃

TPMW 32.52 TPMW16T308 0.031" 䖃

䖃㻌: Line up

TP*T TPGM0701 TPGM (A) 0902~1603 TPGH 0701** 0802** 0902** 1102** 1103** 1303** 1603** 16T3**
Mounting hole
specifications

60° 60° 80° 81°

TP*T(W) - 0.091 0.098 0.110 0.134 0.134 - 0.173
ød1 (in)

TPGM(A) 0.106 - 0.126 0.118 0.118 - 0.157 -

ød1 ød1 ød1 ød1 TPGH - 0.091 0.118 0.134 0.134 - 0.177 -

Reference pages
External toolholders → B258 - B260 Internal toolholders → B309 -

Tungaloy B143
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel C CL CL CL C
M Stainless C CL CL C
Triangular, 60° K Cast iron C CL C
with hole N Non-ferrous C
Positive 11° S Superalloys C CL
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

SH730
SH725
GH110

TH10
Inch Metric
- TPGA 731 TPGA090204 0.016" 䖃

TPGA 21.50.5 TPGA110202 0.008" 䖃 䖃

Positive

TPGA 21.51 TPGA110204 0.016" 䖃

TPGA 220.5 TPGA110302 0.008" 䖃 䖃

TPGA 221 TPGA110304 0.016" 䖃

Finishing to medium cutting

TPGA 321 TPGA160304 0.016" 䖃 䖃

TPGA 322 TPGA160308 0.031" 䖃

- TPGW 730.5 TPGW090202 0.008" 䖃

TPGW 731 TPGW090204 0.016" 䖃

TPGW 21.50.5 TPGW110202 0.008" 䖃

TPGW 21.51 TPGW110204 0.016" 䖃 䖃

TPGW 221 TPGW110304 0.016" 䖃

TPGW 2.521 TPGW130304 0.016" 䖃

TPGW 32.51 TPGW16T304 0.016" 䖃 䖃

TPGW 32.52 TPGW16T308 0.031" 䖃

For internal turning

JS TPGT 5.520 JS TPGT070101-JS 0.004" 䖃

on small lathes

TPGT 5.520.5 JS TPGT070102-JS 0.008" 䖃

TPGT 5.521 JS TPGT070104-JS 0.016" 䖃

JS TPGT 5.520 F-JS TPGT070101F-JS 䖃

For internal turning on

0.004"
䖃
(Sharp edge)

TPGT 5.520.5 F-JS TPGT070102F-JS 0.008"

small lathes

TPGT 5.521 F-JS TPGT070104F-JS 0.016" 䖃

T
䖃㻌: Line up

Reference pages
External toolholders → B258 - B260 Internal toolholders → B309 -

B144 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L CL C

Insert
M Stainless L C
Triangular, 60° K Cast iron CL L L CL C
without hole N Non-ferrous C
Positive 11° S Superalloys C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

AH725
T9125
T9115

T5115

TH10
Inch Metric
PS TPMR 221 PS TPMR110304-PS 0.016" 䖃
Finishing to medium cutting

TPMR 222 PS TPMR110308-PS 0.031" 䖃

Positive
TPMR 331 PS TPMR160304-PS 0.016" 䖃

TPMR 332 PS TPMR160308-PS 0.031" 䖃

23 TPMR 221 TN23 TPMR110304-23 0.016" 䖃 䖃 䖃

TPMR 222 TN23 TPMR110308-23 0.031" 䖃 䖃 䖃

TPMR 321 TN23 TPMR160304-23 0.016" 䖃 䖃 䖃 䖃

TPMR 322 TN23 TPMR160308-23 0.031" 䖃 䖃

24 TPMR 221-24 TPMR110304-24 0.016" 䖃 䖃

Medium cutting

TPMR 222-24 TPMR110308-24 0.031" 䖃 䖃

TPMR 321-24 TPMR160304-24 0.016" 䖃 䖃 䖃 䖃

TPMR 322-24 TPMR160308-24 0.031" 䖃 䖃 䖃

CM TPMR 221 CM TPMR110304-CM 0.016" 䖃

Finishing to medium

TPMR 222 CM TPMR110308-CM 0.031" 䖃

cutting

TPMR 321 CM TPMR160304-CM 0.016" 䖃

TPMR 322 CM TPMR160308-CM 0.031" 䖃

TPMR 323 CM TPMR160312-CM 0.047" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B258 - B260 Internal toolholders → B335

Tungaloy B145
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel C CL CL CL L C L
M Stainless C CL CL C L
Triangular, 60° K Cast iron L C CL CL CL L C C
without hole N Non-ferrous C
Positive 11° S Superalloys C CL
H Hard materials C
Coated Cermet Uncoated Ceramics
Application

Corner
radius

NS9530
Chipbreaker Designation

AH120
GH110

NS740
T3130
T5115

UX30

LX21
TH10

LX11
Inch Metric
- TPGR 220.5L TPGR110302L 0.008" 䖃

TPGR 221L TPGR110304L 0.016" 䖃

Positive

TPGR 321R TPGR160304R 0.016" 䖃

TPGR 321L TPGR160304L 0.016" 䖃

TPGR 322L TPGR160308L 0.031" 䖃

- TPU 221 TPMN110304 0.016" 䖃 䖃 䖃

TPU 222 TPMN110308 0.031" 䖃 䖃 䖃

TPU 321 TPMN160304 0.016" 䖃 䖃 䖃 䖃 䖃

Finishing to medium cutting

TPU 322 TPMN160308 0.031" 䖃 䖃 䖃 䖃 䖃

TPU 323 TPMN160312 0.047" 䖃

TPU 431 TPMN220404 0.016" 䖃

TPU 432 TPMN220408 0.031" 䖃 䖃 䖃

TPU 433 TPMN220412 0.047" 䖃

- TPG 220.5 TPGN110302 0.008" 䖃

TPG 221 TPGN110304 0.016" 䖃 䖃 䖃 䖃 䖃

TPG 222 TPGN110308 0.031" 䖃 䖃 䖃

TPG 320.5 TPGN160302 0.008" 䖃

TPG 321 TPGN160304 0.016" 䖃 䖃 䖃 䖃 䖃

TPG 322 TPGN160308 0.031" 䖃 䖃 䖃 䖃 䖃

TPG 323 TPGN160312 0.047" 䖃 䖃

TPG 431 TPGN220404 0.016" 䖃 䖃

TPG 432 TPGN220408 0.031" 䖃 䖃

TPG 433 TPGN220412 0.047" 䖃

䖃㻌: Line up
T

Reference pages
External toolholders → B258 - B260 Internal toolholders → B335

B146 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L CL CL

Insert
M Stainless C L L H CL L
Rhombic, 35° K Cast iron CL CL L CL L CL CL
with hole N Non-ferrous
Positive 5° S Superalloys CL C
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115

T5115
T515
Inch Metric
PSF VBMT 220.5 PSF VBMT110302-PSF 0.008" 䖃 䖃 䖃

VBMT 221 PSF VBMT110304-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

Positive
VBMT 330.5 PSF VBMT160402-PSF 0.008" 䖃 䖃 䖃

VBMT 331 PSF VBMT160404-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

Finishing

PF VBMT 220.5 PF VBMT110302-PF 0.008" 䖃 䖃

VBMT 221 PF VBMT110304-PF 0.016" 䖃 䖃

VBMT 222 PF VBMT110308-PF 0.031" 䖃 䖃

VBMT 331 PF VBMT160404-PF 0.016" 䖃 䖃

VBMT 332 PF VBMT160408-PF 0.031" 䖃 䖃 䖃

PSS VBMT 221 PSS VBMT110304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to light

VBMT 222 PSS VBMT110308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

cutting

VBMT 331 PSS VBMT160404-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VBMT 332 PSS VBMT160408-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VBMT 333 PSS VBMT160412-PSS 0.047" 䖃 䖃 䖃

PS VBMT 220.5 PS VBMT110302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium

VBMT 221 PS VBMT110304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VBMT 222 PS VBMT110308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

cutting

VBMT 330.5 PS VBMT160402-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VBMT 331 PS VBMT160404-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VBMT 332 PS VBMT160408-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

24 0.016" 䖃 䖃 䖃
Medium cutting

VBMT 331-24 VBMT160404-24

VBMT 332-24 VBMT160408-24 0.031" 䖃 䖃 䖃

V
䖃
Finishing to medium

CM VBMT 221 CM VBMT110304-CM 0.016"

VBMT 222 CM VBMT110308-CM 0.031" 䖃

cutting

VBMT 331 CM VBMT160404-CM 0.016" 䖃 䖃

VBMT 332 CM VBMT160408-CM 0.031" 䖃 䖃

VBMT 333 CM VBMT160412-CM 0.047" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B229 Internal toolholders → B306 -
J series toolholders → B371 - B374

Tungaloy B147
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel L CL CL CL CL CL C
M Stainless L CL CL CL C
Rhombic, 35° K Cast iron L CL CL C
with hole N Non-ferrous C
Positive 5° S Superalloys C CL
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
Chipbreaker Designation

AH725

SH730
SH725

J9530

TH10
J740
Inch Metric
JS 䖃 䖃
small lathes (Sharp edge)

VBGT 22 FN JS VBGT110300FN-JS 0.0012"

For external turning on

VBGT 220 FN JS VBGT110301FN-JS 0.004" 䖃 䖃

Positive

VBGT 220.5 FN JS VBGT110302FN-JS 0.008" 䖃 䖃

VBGT 221 FN JS VBGT110304FN-JS 0.016" 䖃 䖃

For external turning on small lathes For external turning

JS VBGT 220 N JS VBGT110301N-JS 0.004" 䖃

on small lathes

VBGT 220.5 N JS VBGT110302N-JS 0.008" 䖃

VBGT 221 N JS VBGT110304N-JS 0.016" 䖃

J10 VBGT 22 FR J10 VBGT110300FR-J10 0.0012" 䖃 䖃 䖃

VBGT 22 FL J10 VBGT110300FL-J10 0.0012" 䖃 䖃 䖃

VBGT 220 FR J10 VBGT110301FR-J10 0.004" 䖃 䖃 䖃 䖃

(Sharp edge)

VBGT 220 FL J10 VBGT110301FL-J10 0.004" 䖃 䖃 䖃 䖃

VBGT 220.5 FR J10 VBGT110302FR-J10 0.008" 䖃 䖃 䖃 䖃

VBGT 220.5 FL J10 VBGT110302FL-J10 0.008" 䖃 䖃 䖃 䖃

VBGT 221 FR J10 VBGT110304FR-J10 0.016" 䖃 䖃 䖃 䖃

VBGT 221 FL J10 VBGT110304FL-J10 0.016" 䖃 䖃 䖃 䖃

J10 VBGT 220.5R J10 VBGT110302R-J10 0.008" 䖃

On small lathes
(Honed edge)

VBGT 220.5L J10 VBGT110302L-J10 0.008" 䖃

VBGT 221R J10 VBGT110304R-J10 0.016" 䖃

VBGT 221L J10 VBGT110304L-J10 0.016" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B229 Internal toolholders → B306 -
J series toolholders → B371 - B374

B148 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL LH L H LH H CL L CL CL

Insert
M Stainless C L L H CL L C L
Rhombic, 35° K Cast iron CL CL L CL CL
with hole N Non-ferrous
Positive 7° S Superalloys CL C C L L
H Hard materials
Coated Coated Cermet
cermet
Application

Corner
radius

AH8005

NS9530
AH8015

GT9530
Chipbreaker Designation

AH905
AH630
AH645

AH725
AH120
T9125

T6130
T6120
T9115
Inch Metric
PSF VCMT 630.5 PSF VCMT080202-PSF 0.008" 䖃 䖃 䖃

VCMT 631 PSF VCMT080204-PSF 0.016" 䖃 䖃 䖃 䖃 䖃

Positive
VCMT 220.5 PSF VCMT110302-PSF 0.008" 䖃

VCMT 221 PSF VCMT110304-PSF 0.016" 䖃 䖃 䖃

VCMT 331 PSF VCMT160404-PSF 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing

VCMT 332 PSF VCMT160408-PSF 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

PF VCMT 630.5 PF VCMT080202-PF 0.008" 䖃 䖃

VCMT 631 PF VCMT080204-PF 0.016" 䖃 䖃

VCMT 331 PF VCMT160404-PF 0.016" 䖃 䖃

VCMT 332 PF VCMT160408-PF 0.031" 䖃 䖃

PSS VCMT 221 PSS VCMT110304-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to light

VCMT 222 PSS VCMT110308-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

cutting

VCMT 331 PSS VCMT160404-PSS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VCMT 332 PSS VCMT160408-PSS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

PS VCMT 220.5 PS VCMT110302-PS 0.008" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

Finishing to medium

VCMT 221 PS VCMT110304-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

cutting

VCMT 222 PS VCMT110308-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VCMT 331 PS VCMT160404-PS 0.016" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

VCMT 332 PS VCMT160408-PS 0.031" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B262 - Internal toolholders → B306 -
TungCap → F011

Tungaloy B149
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL LH CL
M Stainless C L
Rhombic, 35° K Cast iron CL CL L CL C
with hole N Non-ferrous C
Positive 7° S Superalloys C L L C
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

AH8005

NS9530
AH8015
Chipbreaker Designation

AH905

KS05F
T9125
T9115

T5115
T515
Inch Metric
24 VCMT 331-24 VCMT160404-24 0.016" 䖃 䖃 䖃
Finishing to medium cutting

VCMT 332-24 VCMT160408-24 0.031" 䖃 䖃 䖃

Positive

CM VCMT 631 CM VCMT080204-CM 0.016" 䖃

VCMT 331 CM VCMT160404-CM 0.016" 䖃 䖃

VCMT 332 CM VCMT160408-CM 0.031" 䖃 䖃

VCMT 333 CM VCMT160412-CM 0.047" 䖃

All-round VCMT 331 VCMT160404 䖃 䖃 䖃

Finishing to medium Medium cutting

0.016"

VCMT 332 VCMT160408 0.031" 䖃 䖃 䖃

VCMT 333 VCMT160412 0.047" 䖃 䖃 䖃

AL VCGT 331 AL VCGT160404-AL 0.016" 䖃

VCGT 332 AL VCGT160408-AL 0.031" 䖃

cutting

VCGT 333 AL VCGT160412-AL 0.047" 䖃

VCGT 43.56 AL VCGT220520-AL 0.079" 䖃

VCGT 43.58 AL VCGT220530-AL 0.118" 䖃

䖃㻌: Line up

Reference pages
VC*T... : External toolholders → B262 -, Internal toolholders → B306 -
VPET... : J series toolholders → B375

B150 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL

Insert
M Stainless CL CL
Rhombic, 35° K Cast iron
with hole N Non-ferrous
Positive 11° S Superalloys CL
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

SH730
SH725
Inch Metric
JPP VPET 63X MFR-JPP VPET0802008MFR-JPP <0.0031"* 䖃 䖃
VPET 63X MFL-JPP VPET0802008MFL-JPP <0.0031"* 䖃 䖃

Positive
VPET 630.2 MFR-JPP VPET080201MFR-JPP <0.004"* 䖃 䖃

VPET 630.2 MFL-JPP VPET080201MFL-JPP <0.004"* 䖃 䖃

VPET 630.4 MFR-JPP VPET0802018MFR-JPP <0.007"* 䖃 䖃

VPET 630.4 MFL-JPP VPET0802018MFL-JPP <0.007"* 䖃 䖃
VPET 630.5 MFR-JPP VPET080202MFR-JPP <0.008"* 䖃 䖃

VPET 630.5 MFL-JPP VPET080202MFL-JPP <0.008"* 䖃 䖃

VPET 22X MFR-JPP VPET1103008MFR-JPP <0.0031"* 䖃 䖃

For external turning on small lathes (Sharp edge)

VPET 22X MFL-JPP VPET1103008MFL-JPP <0.0031"* 䖃 䖃

VPET 220.2 MFR-JPP VPET110301MFR-JPP <0.004"* 䖃 䖃

VPET 220.2 MFL-JPP VPET110301MFL-JPP <0.004"* 䖃 䖃

VPET 220.4 MFR-JPP VPET1103018MFR-JPP <0.007"* 䖃 䖃

VPET 220.4 MFL-JPP VPET1103018MFL-JPP <0.007"* 䖃 䖃

VPET 220.5 MFR-JPP VPET110302MFR-JPP <0.008"* 䖃 䖃

VPET 220.5 MFL-JPP VPET110302MFL-JPP <0.008"* 䖃 䖃

JRP VPET 63X MFR-JRP VPET0802008MFR-JRP <0.0031"* 䖃 䖃

VPET 63X MFL-JRP VPET0802008MFL-JRP <0.0031"* 䖃 䖃
VPET 630.2 MFR-JRP VPET080201MFR-JRP <0.004"* 䖃 䖃

VPET 630.2 MFL-JRP VPET080201MFL-JRP <0.004"* 䖃 䖃

VPET 630.4 MFR-JRP VPET0802018MFR-JRP <0.007"* 䖃 䖃

VPET 630.4 MFL-JRP VPET0802018MFL-JRP <0.007"* 䖃 䖃
VPET 630.5 MFR-JRP VPET080202MFR-JRP <0.008"* 䖃 䖃

VPET 630.5 MFL-JRP VPET080202MFL-JRP <0.008"* 䖃 䖃

VPET 22X MFR-JRP VPET1103008MFR-JRP <0.0031"* 䖃 䖃

VPET 22X MFL-JRP VPET1103008MFL-JRP <0.0031"* 䖃 䖃
VPET 220.2 MFR-JRP VPET110301MFR-JRP <0.004"* 䖃 䖃

VPET 220.2 MFL-JRP VPET110301MFL-JRP <0.004"* 䖃 䖃

VPET 220.4 MFR-JRP VPET1103018MFR-JRP <0.007"* 䖃 䖃 V

VPET 220.4 MFL-JRP VPET1103018MFL-JRP <0.007"* 䖃 䖃

VPET 220.5 MFR-JRP VPET110302MFR-JRP <0.008"* 䖃 䖃

VPET 220.5 MFL-JRP VPET110302MFL-JRP <0.008"* 䖃 䖃

JSP VPET 63X MFN-JSP VPET0802008MFN-JSP <0.0031"* 䖃 䖃

small lathes (Sharp edge)
For external turning on

VPET 630.2 MFN-JSP VPET080201MFN-JSP <0.004"* 䖃 䖃

VPET 630.4 MFN-JSP VPET0802018MFN-JSP <0.007"* 䖃 䖃

VPET 630.5 MFN-JSP VPET080202MFN-JSP <0.008"* 䖃 䖃

VPET 22X MFN-JSP VPET1103008MFN-JSP <0.0031"* 䖃 䖃

VPET 220.2 MFN-JSP VPET110301MFN-JSP <0.004"* 䖃 䖃

VPET 220.4 MFN-JSP VPET1103018MFN-JSP <0.007"* 䖃 䖃

VPET 220.5 MFN-JSP VPET110302MFN-JSP <0.008"* 䖃 䖃

* Corner radius has minus tolerance. 䖃㻌: Line up

Note: See page B051 for chipbreaker descriptions.

Tungaloy B151
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL
D OU B LE-S I DED M Stainless CL
K Cast iron
Rhombic, 35° N Non-ferrous
with hole S Superalloys
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

SH725
Inch Metric
JRP VXGU 73.50 MFRE-JRP VXGU09T201MFRE-JRP <0.004"* 䖃
(Sharp edge)

VXGU 73.50 MFLE-JRP VXGU09T201MFLE-JRP <0.004"* 䖃

Positive

Finishing

VXGU 73.50.5 MFRE-JRP VXGU09T202MFRE-JRP <0.008"* 䖃

VXGU 73.50.5 MFLE-JRP VXGU09T202MFLE-JRP <0.008"* 䖃

* Corner radius has minus tolerance. 䖃㻌: Line up

POSITIVE TYPE P Steel CL LH CL

M Stainless CL
Trigon, 80° K Cast iron CL CL
with hole N Non-ferrous
Positive 11° S Superalloys CL
H Hard materials
Coated
Application

Corner
radius

Chipbreaker Designation
AH120
T9125
T9115

Inch Metric
ML - WPMT090725ZPR-ML 0.098" 䖃 䖃 䖃
Heavy cutting

- WPMT090725ZPL-ML 0.098" 䖃 䖃 䖃

䖃㻌: Line up

Reference pages
VXGU... : External toolholders → B194 - B197, B228
WPMT... : External toolholders → B275

B152 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel C CL CL CL C L

Insert
M Stainless C CL CL C L
Trigon, 80° K Cast iron C CL C
with hole N Non-ferrous C
Positive 5° S Superalloys C CL
H Hard materials
Coated Cermet Uncoated
Application

Corner
radius

NS9530
Chipbreaker Designation

SH730
SH725
GH110

UX30
TH10
Inch Metric
W08 WBGT 72V-R W08 WBGT030100R-W08 0.0012" 䖃

WBGT 72V-L W08 WBGT030100L-W08 0.0012" 䖃 䖃 䖃 䖃

Positive
WBGT 72.50-R W08 WBGT030101R-W08 0.004" 䖃

䖃 䖃
Finishing

WBGT 72.50-L W08 WBGT030101L-W08 0.004"

WBGT 720.5-R W08 WBGT030102R-W08 0.008" 䖃

WBGT 720.5-L W08 WBGT030102L-W08 0.008" 䖃 䖃 䖃 䖃 䖃

WBGT 72.51-R W08 WBGT030104R-W08 0.016" 䖃

WBGT 72.51-L W08 WBGT030104L-W08 0.016" 䖃 䖃 䖃 䖃 䖃

W08 WBGT 52 FL-W08 WBGT030100FL-W08 0.0012" 䖃

WBGT 52 FR-W08 WBGT030100FR-W08 0.0012" 䖃

WBGT 520 FL-W08 WBGT030101FL-W08 0.004" 䖃

WBGT 520 FR-W08 WBGT030101FR-W08 0.004" 䖃

WBGT 520.5 FL-W08 WBGT030102FL-W08 0.008" 䖃

Finishing (Sharp edge)

WBGT 520.5 FR-W08 WBGT030102FR-W08 0.008" 䖃

WBGT 521 FL-W08 WBGT030104FL-W08 0.016" 䖃

WBGT 521 FR-W08 WBGT030104FR-W08 0.016" 䖃

W11 WBGT 310.5L W11 WBGT060102L-W11 0.008" 䖃 䖃

WBGT 31.51L W11 WBGT060104L-W11 0.016" 䖃

WBGT 410.5L W11 WBGT080202L-W11 0.008" 䖃

WBGT 41.51L W11 WBGT080204L-W11 0.016" 䖃

JS WBGT 52.50R JS WBGT030101R-JS 0.004" 䖃

For internal turning

WBGT 52.50L JS WBGT030101L-JS 0.004" 䖃

on small lathes

WBGT 520.5R JS WBGT030102R-JS 0.008" 䖃

WBGT 520.5L JS WBGT030102L-JS 0.008" 䖃

WBGT 521R JS WBGT030104R-JS 0.016" 䖃

WBGT 521L JS WBGT030104L-JS 0.016" 䖃

W
JS WBGT 520 FL-JS WBGT030101FL-JS 0.004" 䖃
small lathes (Sharp edge)
For internal turning on

WBGT 520 FR-JS WBGT030101FR-JS 0.004" 䖃

WBGT 520.5 FL-JS WBGT030102FL-JS 0.008" 䖃

WBGT 520.5 FR-JS WBGT030102FR-JS 0.008" 䖃

WBGT 521 FL-JS WBGT030104FL-JS 0.016" 䖃

WBGT 521 FR-JS WBGT030104FR-JS 0.016" 䖃

Reference pages 䖃㻌: Line up

Internal toolholders → B312

Tungaloy B153
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel L CL CL CL
D O U B LE -SI D ED M Stainless L CL
K Cast iron L CL CL C
Trigon, 80° N Non-ferrous C
with hole S Superalloys C C
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
SH725
Inch Metric
(Low cutting force) force) (Sharp edge) medium cutting cutting (Sharp edge)
Finishing to medium

JTS WXGU 220 MFR-JTS WXGU040301MFR-JTS <0.004"* 䖃

WXGU 220 MFL-JTS WXGU040301MFL-JTS <0.004"* 䖃

Positive

WXGU 220.5 MFR-JTS WXGU040302MFR-JTS <0.008"* 䖃

WXGU 220.5 MFL-JTS WXGU040302MFL-JTS <0.008"* 䖃

JTS WXGU 220 MR-JTS WXGU040301MR-JTS <0.004"* 䖃

Finishing to

WXGU 220 ML-JTS WXGU040301ML-JTS <0.004"* 䖃

WXGU 220.5 MR-JTS WXGU040302MR-JTS <0.008"* 䖃

WXGU 220.5 ML-JTS WXGU040302ML-JTS <0.008"* 䖃
Finishing (Low cutting

JSS WXGU 220 MFR-JSS WXGU040301MFR-JSS <0.004"* 䖃

WXGU 220 MFL-JSS WXGU040301MFL-JSS <0.004"* 䖃

WXGU 220.5 MFR-JSS WXGU040302MFR-JSS <0.008"* 䖃

WXGU 220.5 MFL-JSS WXGU040302MFL-JSS <0.008"* 䖃

JSS WXGU 220 MR-JSS WXGU040301MR-JSS <0.004"* 䖃

WXGU 220 ML-JSS WXGU040301ML-JSS <0.004"* 䖃
Finishing

WXGU 220.5 MR-JSS WXGU040302MR-JSS <0.008"* 䖃

WXGU 220.5 ML-JSS WXGU040302ML-JSS <0.008"* 䖃

TS WXGU 220.5 R TS WXGU040302R-TS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L TS WXGU040302L-TS 0.008" 䖃 䖃 䖃 䖃

medium cutting
Finishing to

WXGU 221 R TS WXGU040304R-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L TS WXGU040304L-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 222 R TS WXGU040308R-TS 0.031" 䖃 䖃 䖃 䖃

WXGU 222 L TS WXGU040308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force) Finishing (Wiper)

TSW WXGU 221 R TSW WXGU040304R-TSW 0.016" 䖃 䖃 䖃

WXGU 221 L TSW WXGU040304L-TSW 0.016" 䖃 䖃 䖃

WXGU 222 R TSW WXGU040308R-TSW 0.031" 䖃 䖃 䖃

W WXGU 222 L TSW WXGU040308L-TSW 0.031" 䖃 䖃 䖃

SS WXGU 220.5 R SS WXGU040302R-SS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L SS WXGU040302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

WXGU 221 R SS WXGU040304R-SS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L SS WXGU040304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

䖃㻌: Line up
Reference pages
External toolholders → B190, B191, B227
Internal toolholders → B288

B154 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel LH CL

Insert
M Stainless
Rhombic, 25° K Cast iron CL
with hole N Non-ferrous
Positive 7° S Superalloys
H Hard materials
Coated Coated
cermet
Application

Corner
radius

GT9530
Chipbreaker Designation

T9125
Inch Metric
ZF - YWMT11T202-ZF 0.008" 䖃 䖃

- YWMT11T204-ZF 0.016" 䖃 䖃

Positive
Finishing to medium cutting

- YWMT16T302-ZF 0.008" 䖃 䖃

- YWMT16T304-ZF 0.016" 䖃 䖃

- YWMT16T308-ZF 0.031" 䖃 䖃

ZM - YWMT11T204-ZM 0.016" 䖃 䖃

- YWMT16T304-ZM 0.016" 䖃 䖃

- YWMT16T308-ZM 0.031" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B231 -
Internal toolholders → B329

Tungaloy B155
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel CL C
M Stainless CL C
K Cast iron C
Front turning N Non-ferrous C
Insert S Superalloys
H Hard materials
Coated Uncoated
Application

Corner
radius
Chipbreaker Designation

TH10
J740
Inch Metric
- - JXFR8000F 0.0012" 䖃 䖃
Front turning

- JXFR8010F 0.004" 䖃 䖃
Positive

P Steel CL C
M Stainless CL C
Reverse turning K Cast iron C
Insert N Non-ferrous C
S Superalloys
H Hard materials
Coated Uncoated
Application

Corner
radius

Chipbreaker Designation

TH10
J740

Inch Metric
- - JXRR8000F 0.0012" 䖃 䖃
Reverse

0.004" 䖃 䖃
turning

- JXRR8010F

P Steel CL C
M Stainless CL C
Back turning K Cast iron C
Insert N Non-ferrous C
S Superalloys
H Hard materials
Coated Uncoated
Application

Corner
radius

Chipbreaker Designation
TH10
J740

Inch Metric
- - JXBR8000F 0.0012" 䖃 䖃
- JXBL8000F 0.0012" 䖃 䖃
- JXBR8005F 0.002" 䖃 䖃
- JXBL8005F 0.002" 䖃 䖃
- JXBR8005 0.002" 䖃
Back turning

- JXBL8005 0.002" 䖃
- JXBR8010F 0.004" 䖃 䖃
OTHERS
- JXBL8010F 0.004" 䖃 䖃
- JXBR8010 0.004" 䖃
- JXBL8010 0.004" 䖃
- JXBR8015F 0.006" 䖃 䖃
- JXBL8015F 0.006" 䖃 䖃
- JXBR8015 0.006" 䖃
- JXBL8015 0.006" 䖃

䖃㻌: Line up

B156 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting

POSITIVE TYPE P Steel CL CL CL CL C

Insert
M Stainless CL CL C
K Cast iron CL CL C
Back turning N Non-ferrous C
Insert S Superalloys
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
Chipbreaker Designation

SH725

J9530

TH10
J740
Inch Metric
- - JTBR3000F 0.0012" 䖃 䖃 䖃

- JTBL3000F 0.0012" 䖃 䖃 䖃

Positive
- JTBR3005F 0.002" 䖃 䖃 䖃

- JTBL3005F 0.002" 䖃 䖃 䖃

- JTBR3005 0.002" 䖃 䖃
Back turning

- JTBL3005 0.002" 䖃

- JTBR3010F 0.004" 䖃 䖃 䖃 䖃

- JTBL3010F 0.004" 䖃 䖃 䖃 䖃

- JTBR3010 0.004" 䖃 䖃

- JTBL3010 0.004" 䖃

- JTBR3015F 0.006" 䖃 䖃

- JTBL3015F 0.006" 䖃

P Steel CL CL CL CL C
M Stainless CL CL C
Back turning K Cast iron CL CL C
Insert N Non-ferrous C
S Superalloys
H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530

Chipbreaker Designation
SH725

J9530

TH10
J740

Inch Metric
- - J10ER005BF 0.002" 䖃 䖃 䖃 䖃

- J10EL005BF 0.002" 䖃 䖃 䖃

- J10ER005B 0.002" 䖃 䖃

- J10EL005B 0.002" 䖃
Back turning

- J10ER010BF 0.004" 䖃 䖃 䖃 䖃

- J10EL010BF 0.004" 䖃 䖃 䖃

- J10ER010B 0.004" 䖃 䖃

- J10EL010B 0.004" 䖃

- J10EL015BF 0.006" 䖃

- J10ER015BF 0.006" 䖃 䖃
OTHERS

Reference pages 䖃㻌: Line up

JXF..., JXR... : J series toolholders → B379

JXB... : J series toolholders → B380
JTB... : J series toolholders → B381
J10E... : J series toolholders → B383

Tungaloy B157
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - Inse r t H : Heavy interrupted cutting
Insert POSITIVE TYPE P Steel C
M Stainless C
K Cast iron C
Back turning N Non-ferrous C
Insert S Superalloys
H Hard materials
Uncoated
Application

Corner
radius
Chipbreaker Designation

TH10
Inch Metric
- - 10ER100B 0.0012" 䖃

- 10EL100B 0.0012" 䖃
Positive

Back turning

- 10ER150B 0.0012" 䖃

- 10EL150B 0.0012" 䖃

- 10ER300 - 䖃

- 10EL300 - 䖃

䖃㻌: Line up

OTHERS

Reference pages
J series toolholders → B383

B158 www.tungaloyamerica.com
 Insert
MEMO

Positive

Tungaloy B159
 Tur nL in e - Designation System for T- CBN (PCBN) Inser ts
Multi-Corner type
Insert

1
2 QP - CNGA120404 -L
2 3 4

1 Number of corners 2 Type 3 ISO symbol

4 Special feature & chipbreaker
CBN
QP Inserts
ISO symbol
Without Standard honing
Light honing angle
-L Wear resistance priority
Heavy honing angle
-H Impact resistance priority
-W Wiper type insert

-W Round wiper type insert

-F Sharp edge
-HF With chipbreaker
PCD / CBN

-HM With chipbreaker

Multi-Corner type (10 inserts packing)

1
T 2 QP- CNGA120408
1 “T” shows 10 inserts packing.

For general turning

TNGA160402 - QBN
1 2

1 ISO symbol 2 CBN inserts

T-CBN (PCBN tipped) grooving Inserts

XG R 63 10 S - QBN
1 2 3 4 5

For grooving tool 2 Insert

Hand of 3 Groove width 4
Corner radius: 5 CBN inserts
1 (mm) rε (mm)
GX-type
L Left 10 1.0 S 0.2
R Right 15 1.5

For

1
S 2
G 3
N 200 - 020 4 5

1 Number of edge 2 Application 3 For use 4 Groove width Corner radius:

5 r (mm)
(mm) ε
S Single corner G Grooving N Non breaker 200 2.0 020 0.2

B160 www.tungaloyamerica.com
Tur nL in e - Designation System for T-DIA (PCD) Inser ts
Inserts for turning

Insert
1
TPGW110204 - DIA 2

1 ISO symbol 2 PCD inserts

ISO symbol T-DIA inserts

Tur nL in e - T- CBN Inser ts GNG A t ype

PCD / CBN
GNGA

Negative relief angle, G class, rhombic insert

with 70° corner angle .

New shape CBN insert for general turning

- 70° corner angle makes large clearance between
insert and workpiece.

- Large clearance reduces the cutting force and 70°

wear on edge, and provides smooth chip flow to
prevent scratches on machined surface by chips.

High versatility
- Standard toolholder for ISO CN**43* insert is
available.

- No need offsets compared to CN**43* insert,

due to same geometry of cutting edge position.

- Double sided insert with 2 cutting edges. 80°

- 4 types of CBN grades are available for 70°

machining of a wide range of materials.

Tungaloy B161
 T-CBN series for machining hardened steels and hard materials
Insert

 Application area Necessity of PCBN grades  Features of CBN grades for

The condition machining hardened steel and
necessary to cut Material is:
Workpiece hardness (HRC)
the work Hardness of tool * Hardness of tool X 3 other hard materials
65
 Hardened steel (60HRC) → 700 Hv  Cemented carbide → 1600 Hv
 PCBN (BX360) → 3300 Hv Impact
60 resistance

Increasing
Effects of grain size of CBN on surface roughness and cutting speed
55 T-CBN [Fine-grained CBN] [Rough-grained CBN]
Ceramic
Wear
50 resistance
45 Coated / Cermet
100
1-2μm 4-8μm CBN content
Continuous Light Heavy Fine grained PCBN provided with Rough grained PCBN. CBN particles Fewer CBN content e Increasing wear resistance
interrupted interrupted sharp cutting edge. are hold firmly.
Cutting mode Good surface roughness Allows high speed machining Much CBN content e Increasing impact resistance

Basic selection of T-CBN grades in machining of hardened steel and hard material
 Coated T-CBN grades  Uncoated T-CBN grades
BXM10 BX310 For high speeds / Priority on wear resistance in continuous cutting
PCD / CBN

For high speeds cutting

For general purpose,
BXM20 more than Vc = 591 sfm BX330 For medium speeds / Priority on surface quality
For general purpose, For low to medium speeds / General purpose grade, excels in
BXA20 less than Vc = 591 sfm
BX360 impact resistance
BX380 For low to medium speeds / Priority on impact
resistance in heavily interrupted cutting

 Application area of coated T-CBN grades

 Continuous cutting  Interrupted cutting
980 980
Cutting speed Vc (sfm)

BXM10
Cutting speed Vc (sfm)

BXM10 Lightly
interrupted
660 BXM20 Continuous 660 BXM20
cutting

BXA20
330 330 BXA20
Interrupted

0 0
0 0.006 0.012 Light Interrupted Heavy
Feed rate (ipr)

Effects of Coated T-CBN grades

 Protect CBN from oxidation wear
Since the coating layer intercepts air, oxidation wear of
Coated on hard CBN CBN can be prevented. Improved resistance
Hardness:  Peeling of coating layer can be protected to flank wear
CBN > Coating layer Hard and deformation resistant CBN is excellent substrate
material.

Effects of coolant in machining of hardened steel

 Continuous cutting Interrupted cutting
Dry Wet 19  In continuous cutting, wet
Cutting conditions
0.004 cutting is superior to dry
Flank wear width VB (in)

 Workpiece material: Chromium

15 molybdenum steel Heavy
Continuous 14 cutting in tool life for wear.
Tool life (min)

0.003 (JIS SCM415), 60 HRC interrupted

cutting

Cutting conditions
 Cutting speed: Vc = 330 sfm
 Depth of cut: ap = 0.010 in
 In interrupted cutting, dry
0.002 10
 Workpiece material: Chromium 10  Feed: f = 0.006 ipr cutting is superior to wet
molybdenum steel
0.001 (JIS SCM415), 60 HRC
5.5
cutting in tool life for
 Cutting speed: Vc = 500 sfm 5
0.0008  Depth of cut: ap = 0.010 in 4 fracture.
BX330  Feed: f = 0.004 ipr BX360 2.5
0 0
10 20 30
Dry Wet
Time in cut (min)

B162 www.tungaloyamerica.com
 T-CBN series for machining sintered metals

Insert
 Application area  Valve seat  Valve seat BX470
 Ferrous Sintered metal (Plunge cutting) (Traverse cutting) Priority on burr prevention and
980 400 400 surface finish

Cutting speed Vc (sfm)

Cutting speed Vc (sfm)

Cutting speed Vc (sfm)

330 330
BX480
BX470 Priority on wear resistance and
BX480 BX470 versatility
BX330
500 BX470
165 165

SMF40X0 series material (JPMA standard)

0 0 0
55 60 65 300 300
Hardness of workpiece material (HRC) Hardness of workpiece material (Hv) Hardness of workpiece material (Hv)

Machining of Sintered metal including hard particles Features of BX470 and BX480
Features of
BX470 and BX480 Conventional grade BX470 / BX480 CBN content: 95 vol%
Hv = 4100 ~ 4300

PCD / CBN
Hard particle Binder CBN grain
The world highest CBN content as a
Binder phase are selectively worn away by hard particles. By increasing CBN content, wear of binder layer is suppressed. commercially available material.
e Wear proceeds with falling-out of CBN grains, e Improved wear resistance

 BX480 (Facing of gears)  BX470/BX480 Tool failure after machining Sintered metal  BX470 (Tool life criterion: Burr occurrence)
300 600
Vc =
Number of machined parts

820 sfm
250

Number of passes
200 400
150 Vc = 400 sfm

100 Conventional BX480 200

PCBN grade
After machining After machining
50 300 pcs.
150 pcs.
0
0 Competitor A Competitor B
Conventional grade BX480 BX470 BX480
Cutting conditions Cutting conditions Cutting conditions
 Workpiece material: Sintered metal (> HRA60)  Workpiece material: Sintered metal (> HRA60), Nitriding,  Workpiece material: Ferrous Sintered metal
 Insert: DCMW11T308 Hard particles included  Cutting speed: Vc = 330 sfm
 Depth of cut: ap = 0.008 ~ 0.020 in  Cutting speed: Vc = 360 sfm  Depth of cut: ap = 0.006 in  Depth of cut: ap = 0.006 ~ 0.012 in
 Feed : f = 0.003 ipr  Feed: f = 0.004 ipr  Coolant : Water soluble type  Feed: f = 0.003 ~ 0.009 ipr
 Coolant : Water soluble type  Interrupted cutting  Dry and interrupted cutting
 Interrupted cutting

T-CBN series for machining grey and ductile cast irons

 Application area  Solid coated T-CBN grades

5000
FC and FCA (JIS) FCD (JIS) BX930 Area for
finishing
Area for roughing
· General purpose, first choice
Cutting speed Vc (sfm)

Cutting speed Vc (sfm)

grade.
· Dedicated grade for machining 5000 Ceramic grades
3300
BX930 ductile Cast iron BXC90 (FX105)
BXC90
· One-piece solid
BX950
BX950 3300
Conventional
structure
1650 · Suitable for interrupted PCBN · Applicable for small
machining to large depths of cut
BX930 · Excels in impact resistance 1650
grades

T5100 series (Coated carbide)

Continuous Interrupted FCD400 FCD700 0 0.040 0.080 0.120 0.160
Depth of cut (in)

 Machining of cylinder liners (Machining example of BX910)  Tool life comparison in machining of disc brakes
Wear width after machining Tool failure after machining 120 pcs. 2000
Number of machine parts (pcs.)

120 pcs.
BXC90
0.020 1600
Ceramic
Max. flank wear width

0.016 BX910 Competitor

1200
Cutting conditions
VBmax (in)

0.012 Cutting conditions

800  Workpiece material: Disc rotor
0.008  Workpiece material: (No.250B)
Cylinder liner (Spin casting)  Insert: SNGN 120412 BXC90
400  Depth of cut: ap = 0.028 in
Machining type: Finish boring
0.004  Feed: f = 0.014 ipr
 Cutting speed: Vc = 3200 sfm  Coolant: Dry
0
0  Machine: Special purpose machine 980 1650 2625 3300  Tool life criterion:
 Coolant: Wet Cutting speed: Vc (sfm) Conditions of finished surface
BX910 Competitor

BX910 For machining cylinder liners

Tungaloy B163
 Tur nL in e - T- CBN Se r ie s
H oni ng sp ec i f i cat i o ns
Insert

 T-CBN inserts with special honing specifications are made to order. Refer to the following description.

Designation system for honing

Example: Honing width W
Honing width: 0.006 in
Honing angle: -30°
With R-honing Rake face

S 0 1 5 3 0 Honing angle α
R-honing

Shape Honing width (W) Honing angle (α) Relief face

T … Chamfered honing Q Symbol
S … Chamfered + R-honing QHoning specification can be selected in combination
Amount of α Honing angle
E … R-honing alone W
honing (in) of items described here.
F … Sharp edge 10° -10°
QInserts with “R” honing alone are available.
005 0.002 15° -15°
PCD / CBN

010 0.004 20° -20°

013 0.005 25° -25° Honing specifications for machining hardened
30° -30° steels and other hard materials
015 0.006
Standard honing: -25° + R-honing
020 0.008 35° -35° “-L” honing : -15° + R-honing
40° -40° “-H” honing : -35° + R-honing

 Relationship between honing angle and tool life in continuous turning  Relationship between honing angle and tool life in interrupted turning
150 300
Cutting conditions Cutting conditions
Time in cut: T (min)

Workpiece material: Workpiece material:

125 Chromium molybdenum steel Chromium molybdenum steel
Tool life (%)

(JIS SCM415), 60 HRC 200 (JIS SCM415), 60 HRC

Insert: TNGN160404 BX360 Insert: TNGN160404 BX360
100
Cutting speed: Vc = 330 sfm Cutting speed: Vc = 330 sfm
Feed: f = 0.006 ipr 100 Feed: f = 0.006 ipr
75
Depth of cut: ap = 0.010 in Depth of cut: ap = 0.010 in
Coolant: Dry Coolant: Dry
50 0
−15º −20º −25º −30º −35º −40º Tool life criterion: VBmax = 0.006 in −15º −20º −25º −30º −35º −40º Tool life criterion: Fracture
Honing angle Honing angle
Honing: -°+ R-honing Honing: -°+ R-honing

 General rule
• For continuous cutting, small honing angle is favorable to minimize wear in general.
• For interrupted cutting, large honing angle is favorable to minimize fracture in general.
 Standard honing specifications
Grades BXM10 BXM20 BXA20 BXC50 BX310 BX330 BX360 BX380 BX470 BX480 BX910 BX930 BX950
Negative insert S01325 S01325 S01325 S01325 S01325 S01325 S01325 S01325 T01315 S01325 S01315 S01315 S01325
Positive insert S01325 S01325 S01325 − S00515 S00515 S00515 − T01315 − S01315 S00515 S00515

W i p er i nser t Wiper edge geometry

 A finishing edge (wiper edge) is formed at the point of intersection

between corner radius and straight cutting edge.
 Effect of wiper edge
 Doubles the productivity J Reduced machining time
The wiper edge can double the feed rate and moreover does not deteriorate the
surface roughness. (Note: Feed rate: *f < 0.012 ipr)
 Superior surface roughness J By integrating roughing and finishing into one
process, productivity can be increased.
Wiper edge
Compared with conventional inserts only with corner radius, surface roughness
can be improved with the wiper edge.

 Profiles of surface roughness  Recommended toolholders for wiper-edged inserts

Sectional profile of surface machined
with conventional insert 2QP-CNGA43*WL 3QP-WNGA432WL 2QP-DNGA43*WJ 3QP-TNGA33*WG
Removed End cutting
angle 95° 93° 91°
ATGNR/L**3-A
ACLNR/L**4-A AWLNR/L**4-A ADJNR/L**4-A
External ATFNR/L**3-A
Sectional profile of toolholder
DTGNR/L**3
surface machined with DCLNR/L**4 DWLNR/L**4 DDJNR/L**4
wiper insert DTFNR/L**3
When machining When machining Internal A**-ACLNR/L4-D... A**-AWLNR/L4-D... A**-ADUNR/L4-D... A**-ATFNR/L3-D...
with conventional with wiper insert toolholder
insert

B164 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Negati ve i nser t · M ul t i - co rner t y p e

Insert
P Steel
M Stainless
K Cast iron CL H CL L
N Non-ferrous
S Superalloys C
H Hard materials C CL CL H C CL CL H
Sintered metal CL LH

Length
Corner

corner
radius

No. of

CBN

BXM20
BXM10

BXA20
BXC50

BX380
BX360
BX330

BX480
BX930
BX950
BX470
BX310
Specification Shape Designation

Inch Metric
2QP-CNGA 431-F 2QP-CNGA120404F 0.016" 2 0.091" 䖃
Sharp edge
2QP-CNGA 432-F 2QP-CNGA120408F 0.031" 2 0.087" 䖃
2QP-CNGA 431 2QP-CNGA120404 0.016" 2 0.091" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
General
2QP-CNGA 432 2QP-CNGA120408 0.031" 2 0.087" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose
2QP-CNGA 433 2QP-CNGA120412 0.047" 2 0.094" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
2QP-CNGA 431-L 2QP-CNGA120404-L 0.016" 2 0.091" 䖃 䖃 䖃
Light honing 2QP-CNGA 432-L 2QP-CNGA120408-L 0.031" 2 0.087" 䖃 䖃 䖃

PCD / CBN
2QP-CNGA 433-L 2QP-CNGA120412-L 0.047" 2 0.094" 䖃 䖃 䖃
2QP-CNGA 431-H 2QP-CNGA120404-H 0.016" 2 0.091" 䖃 䖃 䖃
Heavy honing 2QP-CNGA 432-H 2QP-CNGA120408-H 0.031" 2 0.087" 䖃 䖃 䖃 䖃
2QP-CNGA 433-H 2QP-CNGA120412-H 0.047" 2 0.094" 䖃 䖃 䖃
2QP-CNGA 431-WL 2QP-CNGA120404WL 0.016" 2 0.091" 䖃 䖃
2QP-CNGA 432-WL 2QP-CNGA120408WL 0.031" 2 0.087" 䖃 䖃 䖃
2QP-CNGA 433-WL 2QP-CNGA120412WL 0.047" 2 0.094" 䖃 䖃
2QP-CNGA 431-W 2QP-CNGA120404-W 0.016" 2 0.091" 䖃
Wiper edge
2QP-CNGA 432-W 2QP-CNGA120408-W 0.031" 2 0.087" 䖃
2QP-CNMA 431-W 2QP-CNMA120404W 0.016" 2 0.091" 䖃
2QP-CNMA 432-W 2QP-CNMA120408W 0.031" 2 0.087" 䖃
2QP-CNMA 433-W 2QP-CNMA120412W 0.047" 2 0.094" 䖃
General T2QP-CNGA 431 T2QP-CNGA120404 0.016" 2 0.091" 䖃
purpose T2QP-CNGA 432 T2QP-CNGA120408 0.031" 2 0.087" 䖃
4QP-CNGA 431 4QP-CNGA120404 0.016" 4 0.091" 䖃
General
4QP-CNGA 432 4QP-CNGA120408 0.031" 4 0.087" 䖃
purpose
4QP-CNGA 433 4QP-CNGA120412 0.047" 4 0.094" 䖃
4QP-CNMA 431-W 4QP-CNMA120404W 0.016" 4 0.091" 䖃
Wiper edge 4QP-CNMA 432-W 4QP-CNMA120408W 0.031" 4 0.087" 䖃
4QP-CNMA 433-W 4QP-CNMA120412W 0.047" 4 0.094" 䖃
General * 2QP-GNGA 431 * 2QP-GNGA120404 0.016" 2 0.091" 䖃 䖃 䖃
purpose * 2QP-GNGA 432 * 2QP-GNGA120408 0.031" 2 0.087" 䖃 䖃 䖃 䖃 䖃
Nose angle
70º * 2QP-GNGA 433 * 2QP-GNGA120412 0.047" 2 0.094" 䖃 䖃 䖃 䖃 䖃
2QP-DNGA 431 2QP-DNGA150404 0.016" 2 0.098" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
General
2QP-DNGA 432 2QP-DNGA150408 0.031" 2 0.083" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose
2QP-DNGA 433 2QP-DNGA150412 0.047" 2 0.079" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
2QP-DNGA 431-L 2QP-DNGA150404-L 0.016" 2 0.098" 䖃 䖃 䖃
Light honing 2QP-DNGA 432-L 2QP-DNGA150408-L 0.031" 2 0.083" 䖃 䖃 䖃
2QP-DNGA 433-L 2QP-DNGA150412-L 0.047" 2 0.079" 䖃 䖃
2QP-DNGA 431-H 2QP-DNGA150404-H 0.016" 2 0.098" 䖃 䖃 䖃
Heavy honing 2QP-DNGA 432-H 2QP-DNGA150408-H 0.031" 2 0.083" 䖃 䖃 䖃 䖃
2QP-DNGA 433-H 2QP-DNGA150412-H 0.047" 2 0.079" 䖃 䖃 䖃
2QP-DNGA 431-WJ 2QP-DNGA150404WJ 0.016" 2 0.098" 䖃 䖃 䖃
Wiper edge
2QP-DNGA 432-WJ 2QP-DNGA150408WJ 0.031" 2 0.083" 䖃 䖃 䖃
2QP-DNGA 441 2QP-DNGA150604 0.016" 2 0.098" 䖃 䖃
General
2QP-DNGA 442 2QP-DNGA150608 0.031" 2 0.083" 䖃 䖃 䖃
purpose
2QP-DNGA 443 2QP-DNGA150612 0.047" 2 0.079" 䖃 䖃 䖃
Note:
Letter “T” in the first position of designation shows that the standard packing quantity is 10 pieces.
Recommended toolholders for wiper inserts, W, WL, or WJ are shown on page B164. 䖃㻌: Line up
-W = Straight / Flat Wiper
-WL = Arched Wiper
* Tungaloy's original shape
Reference pages
External toolholders → B208 - Internal toolholders → B321 -
J series toolholders → B376 - TungCap → B223 -, F006 -
Tungaloy B165
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

N egat i ve i ns er t · M ul t i - co rner t y p e
Insert
P Steel
M Stainless
K Cast iron CL H C CL L
N Non-ferrous
S Superalloys C
H Hard materials C L L H C L L H
Sintered metal CL LH

Length
Corner

corner
radius

No. of

CBN

BXM20
BXM10

BXA20
BXC50

BX380
BX360
BX330

BX480

BX930
BX950
BX470

BX910
BX310
Specification Shape Designation

Inch Metric
4QP-DNGA 431 4QP-DNGA150404 0.016" 4 0.098" 䖃
General
4QP-DNGA 432 4QP-DNGA150408 0.031" 4 0.083" 䖃
purpose
4QP-DNGA 433 4QP-DNGA150412 0.047" 4 0.079" 䖃
2QP-SNGA 431 2QP-SNGA120404 0.016" 2 0.094" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
General
2QP-SNGA 432 2QP-SNGA120408 0.031" 2 0.094" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose
2QP-SNGA 433 2QP-SNGA120412 0.047" 2 0.094" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
PCD / CBN

2QP-SNGA 431-L 2QP-SNGA120404-L 0.016" 2 0.094" 䖃

Light honing 2QP-SNGA 432-L 2QP-SNGA120408-L 0.031" 2 0.094" 䖃 䖃
2QP-SNGA 433-L 2QP-SNGA120412-L 0.047" 2 0.094" 䖃 䖃
2QP-SNGA 431-H 2QP-SNGA120404-H 0.016" 2 0.094" 䖃 䖃
Heavy honing 2QP-SNGA 432-H 2QP-SNGA120408-H 0.031" 2 0.094" 䖃 䖃 䖃
2QP-SNGA 433-H 2QP-SNGA120412-H 0.047" 2 0.094" 䖃 䖃 䖃
4QP-SNGA 431 4QP-SNGA120404 0.016" 4 0.094" 䖃
General
4QP-SNGA 432 4QP-SNGA120408 0.031" 4 0.094" 䖃
purpose
4QP-SNGA 433 4QP-SNGA120412 0.047" 4 0.094" 䖃

2QP-SNGN 322 2QP-SNGN090308 0.031" 2 0.094" 䖃

General
purpose 2QP-SNGN 323 2QP-SNGN090312 0.047" 2 0.094" 䖃

3QP-TNGA 331-F 3QP-TNGA160404F 0.016" 3 0.087" 䖃

Sharp edge
3QP-TNGA 332-F 3QP-TNGA160408F 0.031" 3 0.075" 䖃
3QP-TNGA 331 3QP-TNGA160404 0.016" 3 0.087" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
General
3QP-TNGA 332 3QP-TNGA160408 0.031" 3 0.075" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose
3QP-TNGA 333 3QP-TNGA160412 0.047" 3 0.094" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
3QP-TNGA 331-L 3QP-TNGA160404-L 0.016" 3 0.087" 䖃 䖃 䖃
Light honing 3QP-TNGA 332-L 3QP-TNGA160408-L 0.031" 3 0.075" 䖃 䖃 䖃
3QP-TNGA 333-L 3QP-TNGA160412-L 0.047" 3 0.094" 䖃 䖃 䖃
3QP-TNGA 331-H 3QP-TNGA160404-H 0.016" 3 0.087" 䖃 䖃 䖃
Heavy honing 3QP-TNGA 332-H 3QP-TNGA160408-H 0.031" 3 0.075" 䖃 䖃 䖃 䖃
3QP-TNGA 333-H 3QP-TNGA160412-H 0.047" 3 0.094" 䖃 䖃 䖃 䖃
3QP-TNGA 331-WG 3QP-TNGA160404WG 0.016" 3 0.087" 䖃 䖃
Wiper edge
3QP-TNGA 332-WG 3QP-TNGA160408WG 0.031" 3 0.075" 䖃 䖃
General T3QP-TNGA 331 T3QP-TNGA160404 0.016" 3 0.087" 䖃
purpose T3QP-TNGA 332 T3QP-TNGA160408 0.031" 3 0.075" 䖃
6QP-TNGA 331 6QP-TNGA160404 0.016" 6 0.087" 䖃
General
6QP-TNGA 332 6QP-TNGA160408 0.031" 6 0.075" 䖃
purpose
6QP-TNGA 333 6QP-TNGA160412 0.047" 6 0.094" 䖃

Note:
Letter “T” in the first position of designation shows that the standard packing quantity is 10 pieces. 䖃 : Line up
Recommended toolholders for wiper inserts, WG are shown on page B164.

Reference pages
External toolholders → B210 - Internal toolholders → B322 -
J series toolholders → B377 - TungCap → B223 -, F006 -

B166 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Negati ve i nser t · M ul t i - co rner t y p e

Insert
P Steel
M Stainless
K Cast iron CL H CL L
N Non-ferrous
S Superalloys C
H Hard materials C CL CL H C CL CL H
Sintered metal CL LH

Length
Corner

corner
radius

No. of

CBN

BXM20
BXM10

BXA20
BXC50

BX380
BX360
BX330

BX480
BX930
BX950
BX470
BX310
Specification Shape Designation

Inch Metric
2QP-VNGA 331 2QP-VNGA160404 0.016" 2 0.122" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
General
2QP-VNGA 332 2QP-VNGA160408 0.031" 2 0.087" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose
2QP-VNGA 333 2QP-VNGA160412 0.047" 2 0.118" 䖃
2QP-VNGA 331-L 2QP-VNGA160404-L 0.016" 2 0.122" 䖃 䖃 䖃
Light honing
2QP-VNGA 332-L 2QP-VNGA160408-L 0.031" 2 0.087" 䖃 䖃 䖃
2QP-VNGA 331-H 2QP-VNGA160404-H 0.016" 2 0.122" 䖃 䖃 䖃 䖃
Heavy honing

PCD / CBN
2QP-VNGA 332-H 2QP-VNGA160408-H 0.031" 2 0.087" 䖃 䖃 䖃 䖃
General 4QP-VNGA 331 4QP-VNGA160404 0.016" 4 0.122" 䖃
purpose 4QP-VNGA 332 4QP-VNGA160408 0.031" 4 0.087" 䖃
General 3QP-WNGA 432 3QP-WNGA080408 0.031" 3 0.087" 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃
purpose 3QP-WNGA 433 3QP-WNGA080412 0.047" 3 0.106" 䖃

Wiper edge 3QP-WNGA 432-WL 3QP-WNGA080408WL 0.031" 3 0.087" 䖃 䖃

6QP-WNGA 431 6QP-WNGA080404 0.016" 6 0.122" 䖃

General
purpose
6QP-WNGA 432 6QP-WNGA080408 0.031" 6 0.087" 䖃

Note:
Recommended toolholders for wiper inserts, WL are shown on page B164. 䖃㻌: Line up
-WL = Arched Wiper

Negative insert
CBN Length Corner radius

Reference pages
External toolholders → B210 - Internal toolholders → B322 -
TungCap → B223 -, F006 -

Tungaloy B167
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

N egat i ve i ns er t · M ul t i - co rner t y p e H a rd B re a ke r
Insert
( T-C B N i nser t wi t h chi p b reaker) P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL CL

Length
Corner

corner
radius

No. of

CBN

BXM20
BXA20
Specification Shape Designation

Inch Metric
2QP-CNGM 432-HF 2QP-CNGM120408-HF 0.031" 2 0.087" 䖃
2QP-CNGM 433-HF 2QP-CNGM120412-HF 0.047" 2 0.094" 䖃
2QP-DNGM 432-HF 2QP-DNGM150408-HF 0.031" 2 0.083" 䖃
2QP-DNGM 433-HF 2QP-DNGM150412-HF 0.047" 2 0.079" 䖃
3QP-TNGM 332-HF 3QP-TNGM160408-HF 0.031" 3 0.075" 䖃
3QP-TNGM 333-HF 3QP-TNGM160412-HF 0.047" 3 0.094" 䖃

2QP-VNGM 332-HF 2QP-VNGM160408-HF 0.031" 2 0.087" 䖃

PCD / CBN

With
chipbreaker 2QP-CNGM 432-HM 2QP-CNGM120408-HM 0.031" 2 0.087" 䖃 䖃
2QP-CNGM 433-HM 2QP-CNGM120412-HM 0.047" 2 0.094" 䖃 䖃
2QP-DNGM 432-HM 2QP-DNGM150408-HM 0.031" 2 0.083" 䖃
2QP-DNGM 433-HM 2QP-DNGM150412-HM 0.047" 2 0.079" 䖃
3QP-TNGM 332-HM 3QP-TNGM160408-HM 0.031" 3 0.075" 䖃
3QP-TNGM 333-HM 3QP-TNGM160412-HM 0.047" 3 0.087" 䖃

2QP-VNGM 332-HM 2QP-VNGM160408-HM 0.031" 2 0.094" 䖃

䖃㻌: Line up

“Hard Breakers” for removing the carburized layer

Two types of chipbreaker provide excellent chip
control in a wide application range !

HF type For finishing

HF type
Example of chips
0.009 0.020 0.029 0.030

Single sided CBN insert provides

Depth of cut: ap (in)

higher stability in heavy machining.

Excellent chip control in small DoC
due to the high functional nose.
Delivers exceptional surface
finishes. 0.002 0.004 0.006 0.008
Feed: f (ipr)

HM type For medium cutting

HM type
Example of chips
0.009 0.020 0.029 0.030

Single sided CBN insert provides

Depth of cut: ap (in)

higher stability in heavy machining.

Providing ideal chip control in
large DoC by the well designed
chipbreaker. Suitable for medium
cutting or roughing. 0.002 0.004 0.006 0.008
Feed: f (ipr)

B168 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Negati ve i nser t · One- co rner t y p e

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL

Length
Corner

corner
radius

No. of

CBN

BX360
Specification Shape Designation

Inch Metric
CNGA 430.5 QBN CNGA120402-QBN 0.008" 1 0.161" 䖃
CNGA 431 QBN CNGA120404-QBN 0.016" 1 0.157" 䖃
CNGA 432 QBN CNGA120408-QBN 0.031" 1 0.154" 䖃
CNGA 433 QBN CNGA120412-QBN 0.047" 1 0.154" 䖃
DNGA 430.5 QBN DNGA150402-QBN 0.008" 1 0.169" 䖃
DNGA 431 QBN DNGA150404-QBN 0.016" 1 0.161" 䖃
DNGA 432 QBN DNGA150408-QBN 0.031" 1 0.150" 䖃

PCD / CBN
General DNGA 433 QBN DNGA150412-QBN 0.047" 1 0.134" 䖃
purpose SNGA 430.5 QBN SNGA120402-QBN 0.008" 1 0.161" 䖃
SNGA 431 QBN SNGA120404-QBN 0.016" 1 0.161" 䖃
SNGA 432 QBN SNGA120408-QBN 0.031" 1 0.161" 䖃
SNGA 433 QBN SNGA120412-QBN 0.047" 1 0.161" 䖃
TNGA 330.5 QBN TNGA160402-QBN 0.008" 1 0.173" 䖃
TNGA 331 QBN TNGA160404-QBN 0.016" 1 0.165" 䖃
TNGA 332 QBN TNGA160408-QBN 0.031" 1 0.157" 䖃
TNGA 333 QBN TNGA160412-QBN 0.047" 1 0.146" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B208 -  Internal toolholders → B321 -
J series toolholders → B376 -  TungCap → B223 -, F006 -

Tungaloy B169
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Posi t i ve i ns er t · M ul t i - co rner t y p e ( G c la ss)

Insert
P Steel
M Stainless
K Cast iron CL C
N Non-ferrous
S Superalloys
H Hard materials C CL CL
Sintered metal CL

Length
Corner

corner
radius

No. of

CBN

BXM20
BXM10

BXA20
BX470
BX910
Specification Shape Designation

Inch Metric
2QP-CCGW 21.50.5 2QP-CCGW060202 0.008" 2 0.091" 䖃 䖃
General 2QP-CCGW 21.51 2QP-CCGW060204 0.016" 2 0.091" 䖃 䖃 䖃 䖃
purpose 2QP-CCGW 32.51 2QP-CCGW09T304 0.016" 2 0.091" 䖃 䖃 䖃 䖃
2QP-CCGW 32.52 2QP-CCGW09T308 0.031" 2 0.087" 䖃 䖃 䖃 䖃
2QP-DCGW21.50 2QP-DCGW070202 0.008" 2 0.106" 䖃 䖃 䖃
General
2QP-DCGW21.51 2QP-DCGW070204 0.016" 2 0.098" 䖃 䖃 䖃 䖃
purpose
PCD / CBN

2QP-DCGW21.52 2QP-DCGW070208 0.031" 2 0.098" 䖃

2QP-DCGW32.50.5F 2QP-DCGW11T302F 0.008" 2 0.106" 䖃
Sharp edge
2QP-DCGW32.51F 2QP-DCGW11T304F 0.016" 2 0.098" 䖃
2QP-DCGW32.50.5 2QP-DCGW11T302 0.008" 2 0.106" 䖃 䖃
General
2QP-DCGW32.51 2QP-DCGW11T304 0.016" 2 0.098" 䖃 䖃 䖃
purpose
2QP-DCGW32.52 2QP-DCGW11T308 0.031" 2 0.083" 䖃 䖃 䖃 䖃
2QP-SPGW 32.52 2QP-SPGW09T308 0.031" 2 0.094" 䖃
2QP-SPGW 32.53 2QP-SPGW09T312 0.047" 2 0.094" 䖃
General
2QP-SPGW 432 2QP-SPGW120408 0.031" 2 0.094" 䖃
purpose
2QP-SPGW 433 2QP-SPGW120412 0.047" 2 0.094" 䖃
2QP-SPGW 434 2QP-SPGW120416 0.063" 2 0.094" 䖃

2QP-SPGN 322 2QP-SPGN090308 0.031" 2 0.094" 䖃

General
purpose 2QP-SPGN 323 2QP-SPGN090312 0.047" 2 0.094" 䖃

3QP-TPGW 631 3QP-TPGW080204 0.016" 3 0.087" 䖃 䖃

3QP-TPGW 730.5 3QP-TPGW090202 0.008" 3 0.091" 䖃
General 3QP-TPGW 731 3QP-TPGW090204 0.016" 3 0.087" 䖃 䖃
purpose 3QP-TPGW 21.50 3QP-TPGW110202 0.008" 3 0.091" 䖃
3QP-TPGW 21.51 3QP-TPGW110204 0.016" 3 0.087" 䖃 䖃 䖃
3QP-TPGW 21.52 3QP-TPGW110208 0.031" 3 0.087" 䖃
3QP-TPGW 221F 3QP-TPGW110304F 0.016" 3 0.087" 䖃
Sharp edge
3QP-TPGW 222F 3QP-TPGW110308F 0.031" 3 0.078" 䖃
3QP-TPGW 220 3QP-TPGW110302 0.008" 3 0.091" 䖃
3QP-TPGW 221 3QP-TPGW110304 0.016" 3 0.087" 䖃 䖃 䖃 䖃
3QP-TPGW 222 3QP-TPGW110308 0.031" 3 0.087" 䖃 䖃 䖃 䖃 䖃
General
3QP-TPGW 2.520.5 3QP-TPGW130302 0.008" 3 0.091" 䖃
purpose
3QP-TPGW 2.521 3QP-TPGW130304 0.016" 3 0.087" 䖃 䖃
3QP-TPGW 32.51 3QP-TPGW16T304 0.016" 3 0.087" 䖃 䖃
3QP-TPGW 32.52 3QP-TPGW16T308 0.031" 3 0.075" 䖃 䖃
General 3QP-TPGW 331 3QP-TPGW160404 0.016" 3 0.087" 䖃 䖃
purpose 3QP-TPGW 322 3QP-TPGW160408 0.031" 3 0.075" 䖃

3QP-TPGN 222 3QP-TPGN110308 0.031" 3 0.087" 䖃

General
purpose 3QP-TPGN 223 3QP-TPGN110312 0.047" 3 0.094" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B299 -
J series toolholders → B362 -

B170 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Posi ti ve i nser t · M ul t i - co rner t y p e (G c la ss)

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials C CL CL

Length
Corner

corner
radius

No. of

CBN

BXM20
BXM10

BXA20
Specification Shape Designation

Inch Metric
2QP-VBGW 221 2QP-VBGW110304 0.016" 2 0.122" 䖃 䖃 䖃
General 2QP-VBGW 222 2QP-VBGW110308 0.031" 2 0.087" 䖃 䖃 䖃
purpose 2QP-VBGW 331 2QP-VBGW160404 0.016" 2 0.122" 䖃 䖃 䖃
2QP-VBGW 332 2QP-VBGW160408 0.031" 2 0.087" 䖃 䖃 䖃
General
2QP-VCGW 331 2QP-VCGW160404 0.016" 2 0.122" 䖃 䖃
purpose

䖃㻌: Line up

PCD / CBN
Positive insert
CBN Length Corner radius

Reference pages
External toolholders → B229 - Internal toolholders → B306 -
J series toolholders → B371 - TungCap → F011 -

Tungaloy B171
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Posi t i ve i ns er t · M ul t i - co rner t y p e
Insert
P Steel
M Stainless
K Cast iron CL L
N Non-ferrous
S Superalloys C
H Hard materials C CL CL

Length
Corner

corner
radius

No. of

CBN

BX360
BX330

BX930
BX950
BX310
Specification Shape Designation

Inch Metric
2QP-CCMW 21.50.5 2QP-CCMW060202 0.008" 2 0.091" 䖃 䖃 䖃
General 2QP-CCMW 21.51 2QP-CCMW060204 0.016" 2 0.091" 䖃 䖃 䖃 䖃 䖃
purpose 2QP-CCMW 32.51 2QP-CCMW09T304 0.016" 2 0.091" 䖃 䖃 䖃 䖃 䖃
2QP-CCMW 32.52 2QP-CCMW09T308 0.031" 2 0.087" 䖃 䖃 䖃
2QP-DCMW 21.50.5 2QP-DCMW070202 0.008" 2 0.106" 䖃 䖃 䖃
2QP-DCMW 21.51 2QP-DCMW070204 0.016" 2 0.098" 䖃 䖃 䖃 䖃 䖃
General
2QP-DCMW 32.50.5 2QP-DCMW11T302 0.008" 2 0.106" 䖃 䖃 䖃
purpose
PCD / CBN

2QP-DCMW 32.51 2QP-DCMW11T304 0.016" 2 0.098" 䖃 䖃 䖃 䖃 䖃

2QP-DCMW 32.52 2QP-DCMW11T308 0.031" 2 0.083" 䖃 䖃 䖃

General 2QP-SPMN 321 2QP-SPMN090304 0.016" 2 0.094" 䖃 䖃 䖃

purpose 䖃 䖃 䖃
2QP-SPMN 322 2QP-SPMN090308 0.031" 2 0.094"

3QP-TPMW 631 3QP-TPMW080204 0.016" 3 0.087" 䖃 䖃 䖃 䖃

3QP-TPMW 730.5 3QP-TPMW090202 0.008" 3 0.091" 䖃 䖃 䖃
3QP-TPMW 731 3QP-TPMW090204 0.016" 3 0.087" 䖃 䖃 䖃 䖃
3QP-TPMW 21.50.5 3QP-TPMW110202 0.008" 3 0.091" 䖃 䖃 䖃 䖃
3QP-TPMW 21.51 3QP-TPMW110204 0.016" 3 0.087" 䖃 䖃 䖃 䖃
3QP-TPMW 220.5 3QP-TPMW110302 0.008" 3 0.095" 䖃 䖃 䖃 䖃 䖃
General 3QP-TPMW 221 3QP-TPMW110304 0.016" 3 0.087" 䖃 䖃 䖃 䖃 䖃
purpose 3QP-TPMW 222 3QP-TPMW110308 0.031" 3 0.075" 䖃 䖃 䖃 䖃 䖃
3QP-TPMW 2.520.5 3QP-TPMW130302 0.008" 3 0.095" 䖃 䖃 䖃 䖃 䖃
3QP-TPMW 2.521 3QP-TPMW130304 0.016" 3 0.087" 䖃 䖃 䖃 䖃 䖃
3QP-TPMW 32.51 3QP-TPMW16T304 0.016" 3 0.087" 䖃 䖃 䖃 䖃 䖃
3QP-TPMW 32.52 3QP-TPMW16T308 0.031" 3 0.075" 䖃
3QP-TPMW 331 3QP-TPMW160404 0.016" 3 0.087" 䖃 䖃 䖃 䖃
3QP-TPMW 332 3QP-TPMW160408 0.031" 3 0.075" 䖃 䖃 䖃 䖃
3QP-TPU 220.5 3QP-TPMN110302 0.008" 3 0.091" 䖃 䖃 䖃 䖃
3QP-TPU 221 3QP-TPMN110304 0.016" 3 0.087" 䖃 䖃 䖃 䖃
General
3QP-TPU 222 3QP-TPMN110308 0.031" 3 0.075" 䖃 䖃 䖃 䖃
purpose
3QP-TPU 321 3QP-TPMN160304 0.016" 3 0.087" 䖃 䖃 䖃 䖃
3QP-TPU 322 3QP-TPMN160308 0.031" 3 0.075" 䖃 䖃 䖃 䖃
2QP-VBMW221 2QP-VBMW110304 0.016" 2 0.122" 䖃 䖃 䖃 䖃
General 2QP-VBMW222 2QP-VBMW110308 0.031" 2 0.087" 䖃 䖃 䖃 䖃
purpose 2QP-VBMW331 2QP-VBMW160404 0.016" 2 0.122" 䖃 䖃 䖃
2QP-VBMW332 2QP-VBMW160408 0.031" 2 0.087" 䖃 䖃 䖃

General
2QP-VCMW331 2QP-VCMW160404 0.016" 2 0.122" 䖃 䖃 䖃
purpose

䖃㻌: Line up

Reference pages
External toolholders → B228 - Internal toolholders → B299 -
J series toolholders → B362 - TungCap → F011 -

B172 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Posi ti ve i nser t · One- co rner t y p e

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL

Length
Corner

corner
radius

No. of

CBN

BX330
Specification Shape Designation

Inch Metric

Q-CCMW 21.51 Q-CCMW060204 0.016" 1 0.098" 䖃

General
purpose Q-CCMW 32.51 Q-CCMW09T304 0.016" 1 0.098" 䖃

Q-DCMW 21.51 Q-DCMW070204 0.016" 1 0.083" 䖃

General
purpose Q-DCMW 32.51 Q-DCMW11T304 0.016" 1 0.083" 䖃

Q-SPGN 321 Q-SPGN090304 0.016" 1 0.110" 䖃

General

PCD / CBN
purpose Q-SPGN 322 Q-SPGN090308 0.031" 1 0.110" 䖃

Q-TPMW 631 Q-TPMW080204 0.016" 1 0.087" 䖃

Q-TPMW 730.5 Q-TPMW090202 0.008" 1 0.094" 䖃
Q-TPMW 731 Q-TPMW090204 0.016" 1 0.091" 䖃
Q-TPMW 21.50.5 Q-TPMW110202 0.008" 1 0.094" 䖃
Q-TPMW 21.51 Q-TPMW110204 0.016" 1 0.087" 䖃
General Q-TPMW 221 Q-TPMW110304 0.016" 1 0.091" 䖃
purpose Q-TPMW 222 Q-TPMW110308 0.031" 1 0.087" 䖃
Q-TPMW 2.520.5 Q-TPMW130302 0.008" 1 0.094" 䖃
Q-TPMW 2.521 Q-TPMW130304 0.016" 1 0.091" 䖃
Q-TPMW 32.51 Q-TPMW16T304 0.016" 1 0.091" 䖃
Q-TPMW 331 Q-TPMW160404 0.016" 1 0.091" 䖃
Q-TPMW 332 Q-TPMW160408 0.031" 1 0.075" 䖃
Q-TPGN221 Q-TPGN110304 0.016" 1 0.087" 䖃

General Q-TPGN 222 Q-TPGN110308 0.031" 1 0.087" 䖃

purpose Q-TPGN160304 Q-TPGN160304 0.016" 1 0.091" 䖃
Q-TPGN160308 Q-TPGN160308 0.031" 1 0.075" 䖃
Note: Packing Qty : 2 pcs.

Posi ti ve i nser t · M i ni P Steel

M Stainless
K Cast iron CL
N Non-ferrous
S Superalloys
H Hard materials C
Sintered metal CL
Length
Corner

corner
radius

No. of

CBN

BX470
BX310

Specification Shape Designation

Inch Metric
1QP-CCGW 4.51.80.5 1QP-CCGW03X102 0.008" 1 0.055" 䖃 䖃
General 1QP-CCGW 4.51.81 1QP-CCGW03X104 0.016" 1 0.051" 䖃 䖃
purpose 1QP-CCGW 5.52.20.5 1QP-CCGW04T102 0.008" 1 0.075" 䖃 䖃
1QP-CCGW 5.52.21 1QP-CCGW04T104 0.016" 1 0.071" 䖃 䖃
1QP-EPGW 4.51.80.5 1QP-EPGW03X102 0.008" 1 0.055" 䖃 䖃
General 1QP-EPGW 4.51.81 1QP-EPGW03X104 0.016" 1 0.051" 䖃 䖃
purpose 1QP-EPGW 520.5 1QP-EPGW040102 0.008" 1 0.067" 䖃 䖃
1QP-EPGW 521 1QP-EPGW040104 0.016" 1 0.063" 䖃 䖃

䖃㻌: Line up
Reference pages
External toolholders → B228 - Internal toolholders → B299 -
J series toolholders → B362 -

Tungaloy B173
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Posi t i ve i ns er t · One- co rner t y p e

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL

Length
Corner

corner
radius

No. of

CBN

BX360
Specification Shape Designation

Inch Metric
SPG 321 QBN SPGN090304-QBN 0.016" 1 0.161" 䖃
SPG 322 QBN SPGN090308-QBN 0.031" 1 0.161" 䖃
General
SPG 323 QBN SPGN090312-QBN 0.047" 1 0.161" 䖃
purpose
SPG 422 QBN SPGN120308-QBN 0.031" 1 0.161" 䖃
SPG 423 QBN SPGN120312-QBN 0.047" 1 0.161" 䖃
TPGW 730.5 QBN TPGW090202-QBN 0.008" 1 0.130" 䖃
TPGW 731 QBN TPGW090204-QBN 0.016" 1 0.126" 䖃
PCD / CBN

TPGW 21.50.5 QBN TPGW110202-QBN 0.008" 1 0.154" 䖃

TPGW 21.51 QBN TPGW110204-QBN 0.016" 1 0.146" 䖃
General
TPGW 2.520.5 QBN TPGW130302-QBN 0.008" 1 0.154" 䖃
purpose
TPGW 2.521 QBN TPGW130304-QBN 0.016" 1 0.146" 䖃
TPGW 32.50.5 QBN TPGW16T302-QBN 0.008" 1 0.173" 䖃
TPGW 32.51 QBN TPGW16T304-QBN 0.016" 1 0.165" 䖃
TPGW 32.52 QBN TPGW16T308-QBN 0.031" 1 0.157" 䖃
TPG 221 QBN TPGN110304-QBN 0.016" 1 0.146" 䖃
General TPG 222 QBN TPGN110308-QBN 0.031" 1 0.138" 䖃
purpose TPG 321 QBN TPGN160304-QBN 0.016" 1 0.165" 䖃
TPG 322 QBN TPGN160308-QBN 0.031" 1 0.157" 䖃

CPGA 31.51 QBN CPGA090204-QBN 0.016" 1 0.157" 䖃

General
purpose CPGA 31.52 QBN CPGA090208-QBN 0.031" 1 0.150" 䖃

TPGA 730.5 QBN TPGA090202-QBN 0.008" 1 0.122" 䖃

TPGA 731 QBN TPGA090204-QBN 0.016" 1 0.114" 䖃
TPGA 21.50.5 QBN TPGA110202-QBN 0.008" 1 0.154" 䖃
TPGA 21.51 QBN TPGA110204-QBN 0.016" 1 0.146" 䖃
General
TPGA 220.5 QBN TPGA110302-QBN 0.008" 1 0.154" 䖃
purpose
TPGA 221 QBN TPGA110304-QBN 0.016" 1 0.146" 䖃
TPGA 320.5 QBN TPGA160302-QBN 0.008" 1 0.173" 䖃
TPGA 321 QBN TPGA160304-QBN 0.016" 1 0.165" 䖃
TPGA 322 QBN TPGA160308-QBN 0.031" 1 0.157" 䖃

Posi t i ve i ns er t · Ful l - f ace t y p e P Steel

M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL
Length
Corner

corner
radius

No. of

CBN

BX360

Specification Shape Designation

Inch Metric

TBGN 521 QBN TBGN060104-15-QBN 0.016" 3 - 䖃

General
purpose TBGN 522 QBN TBGN060108-15-QBN 0.031" 3 - 䖃

䖃㻌: Line up

Reference pages
External toolholders → B258 - Internal toolholders → B306 -

B174 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

Coated Sol i d C BN (BXC90)

Insert
P Steel
M Stainless
K Cast iron CL
N Non-ferrous
S Superalloys
H Hard materials

Corner

corner
radius

No. of

BXC90
Specification Shape Designation

Inch Metric
S-CNGN 322 S-CNGN090308 0.031" 4 䖃
General S-CNGN 323 S-CNGN090312 0.047" 4 䖃
purpose S-CNGN 432 S-CNGN120408 0.031" 4 䖃
S-CNGN 433 S-CNGN120412 0.047" 4 䖃
S-RNGN 32 S-RNGN090300 - - 䖃
General
S-RNGN 43 S-RNGN120400 - - 䖃
purpose

PCD / CBN
S-SNGN 322 S-SNGN090308 0.031" 8 䖃
S-SNGN 323 S-SNGN090312 0.047" 8 䖃
General S-SNGN 422 S-SNGN120308 0.031" 8 䖃
purpose S-SNGN 423 S-SNGN120312 0.047" 8 䖃
S-SNGN 432 S-SNGN120408 0.031" 8 䖃
S-SNGN 433 S-SNGN120412 0.047" 8 䖃
S-TNGN 222 S-TNGN110308 0.031" 6 䖃
General S-TNGN 223 S-TNGN110312 0.047" 6 䖃
purpose S-TNGN 322 S-TNGN160408 0.031" 6 䖃
S-TNGN 333 S-TNGN160412 0.047" 6 䖃

䖃㻌: Line up

Tungaloy B175
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - CBN Inse r t H : Heavy interrupted cutting

T-C B N ( PC BN t i p p ed ) g ro o v i ng Ins e r t
Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL

Grooving

±0.002"
Corner

corner
radius

No. of

width

BX360
Specification Shape Designation

XGR6310S-QBN 0.008" 1 0.039"

XGR6315S-QBN 0.008" 1 0.059" 䖃
XGR6320S-QBN 0.008" 1 0.079" 䖃
XGR6325S-QBN 0.008" 1 0.098" 䖃
Grooving
XGR6330S-QBN 0.008" 1 0.118" 䖃
XGR6335S-QBN 0.008" 1 0.138" 䖃
XGR6340S-QBN 0.008" 1 0.157" 䖃
PCD / CBN

XGR6345S-QBN 0.008" 1 0.177" 䖃

TungC ut C B N i ns er t f o r hard ened s te e ls

P Steel
M Stainless
K Cast iron
N Non-ferrous
S Superalloys
H Hard materials CL
Grooving

±0.001"
Corner

corner
radius

No. of

width

Specification Shape Designation BX360

SGN200-020 0.008" 1 0.079" 䖃

SGN300-020 0.008" 1 0.118" 䖃
Grooving
SGN400-020 0.008" 1 0.157" 䖃

䖃㻌: Line up

Reference pages
XGR... : Toolholders → C036
SGN... : Toolholders → C060

B176 www.tungaloyamerica.com
 Tur nL in e - PCD grade, T-DIA series

Insert
Expanded product line allows T-DIA tools to be
applied to wider workpiece materials and cutting
conditions.

Features and applications (Physical and mechanical properties)

DX110 DX120 DX140 DX160 DX180

Grade

Super fine grained grade. Fine grained grade. High purity grade for Highly wear resistant grade
Property General purpose grade for special applications
Excels in surface finish. Excels in surface finish. hard materials
Approx.
grain size
of diamond <1 5 13 28 45
(μm)

PCD / CBN
Hardness
(Hv) 8500 12000
(Harder)
Wear
resistance Higher
Grindability
(Cutting
edge Better
sharpness)

Note: T-DIA grades are not suitable for ferrous materials (such as hardened steel, chilled Cast iron ), and Ni- or Co-base Superalloys.

Cutting performance (Wear resistance)

When machining aluminum alloy: Continuous external turning When machining FRP: Face milling
 Workpiece material:
Flank wear width: VB (in)

0.2  Workpiece material:

0.05
0.0020
10 % Si, aluminum alloy Competitor A
Fiber reinforced plastics (FRP)
Flank wear width: VB (in)

Competitor B
0.04
0.0016  Insert: SPGN120308-DIA Competitor C  Insert: SPCN42ZFR-DIA
0.03
0.0012  Toolholder: CSBPR2525M4 0.1 DX140
 Milling cutter: TPG4208R-A
0.02
 Cutting speed: vc = 1640 sfm  Cutting speed: vc = 3090 sfm
0.0008
 Feed: f = 0.004 ipr 0  Feed: f = 0.004 ipr
0.01
0.0004  Depth of cut: ap = 0.020 in 3 6 12
 Coolant: Dry cutting Time in cut (min)  Depth of cut: ap = 0.059 in
0
 Coolant: Dry cutting
DX120 DX140 DX160  Time in cut: 30 min

Grade selection guide

DX120
Excels in cutting-edge
DX110
Super fine grained
 For precision machining sharpness and impact
resistance. grade
DX140  When good surface finish is
required.
Basic selection
(General purpose grade)
 When interrupted cutting is
involved.
DX160 DX180
Superior wear Special purpose
 When machining hard materials resistance  When requiring higher wear grade
such as high silicon aluminum resistance than DX160 (such
alloys (Si > 12 %) as when machining high
 Simultaneous machining of silicon materials, cemented
aluminum alloy and Cast iron. carbides, semi-sintered
 When high wear resistance is required. ceramics, etc.)

STA N DA R D CUT T ING CONDIT IONS F O R T U R N I N G

Grade applicability
ISO Workpiece material Cutting speed Depth of cut Feed
DX110 DX120 DX140 DX160 DX180 vc (sfm) ap (in) f (ipr)
Aluminum alloys (Si < 12 %)   3300 - 8200 0.002 - 0.080 0.002 - 0.008
Aluminum alloys (Si > 12 %)  1300 - 2630 0.002 - 0.080 0.002 - 0.008
Copper, brass   1640 - 4920 0.002 - 0.080 0.002 - 0.008
Phosphor bronze   980 - 1640 0.002 - 0.080 0.002 - 0.008
Carbon, graphite 980 - 1640 0.002 - 0.080 0.002 - 0.008
FRP   1640 - 3300 0.002 - 0.020 0.001 - 0.004
Plastics   1640 - 3300 0.002 - 0.020 0.00039 - 0.002
Cemented carbides (D40 ~ D60)  30 - 65 0.002 - 0.008 0.00039 - 0.002
Semi-sintered ceramics  330 - 500 0.002 - 0.080 0.001 - 0.004

(Note) : First choice  : Second choice

Tungaloy B177
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - PCD Inse r t H : Heavy interrupted cutting

N egat i ve i ns er t (wi t h rake ang l e)

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous CL
S Superalloys
H Hard materials

Length
Corner

corner
radius

No. of

DIA

DX120
Specification Shape Designation

Inch Metric

CNMM 430.5 DIA CNMM120402-DIA 0.008" 1 0.138" 䖃

Low cutting
force CNMM 431 DIA CNMM120404-DIA 0.016" 1 0.138" 䖃

DNMM 430.5 DIA DNMM150402-DIA 0.008" 1 0.130" 䖃

Low cutting
force DNMM 431 DIA DNMM150404-DIA 0.016" 1 0.122" 䖃

TNMM 330.5 DIA TNMM160402-DIA 0.008" 1 0.130" 䖃

Low cutting
PCD / CBN

force TNMM 331 DIA TNMM160404-DIA 0.016" 1 0.126" 䖃

VNMM 330.5 DIA VNMM160402-DIA 0.008" 1 0.189" 䖃

Low cutting
VNMM 331 DIA VNMM160404-DIA 0.016" 1 0.173" 䖃
force
VNMM 332 DIA VNMM160408-DIA 0.031" 1 0.142" 䖃

N egat i ve i ns er t
P Steel
M Stainless
K Cast iron
N Non-ferrous CL CL
S Superalloys
H Hard materials
Length
Corner

corner
radius

No. of

DIA

DX140
Specification Shape Designation DX160
Inch Metric

CNGA 431 DIA CNGA120404-DIA 0.016" 1 0.138" 䖃

General
purpose CNGA 432 DIA CNGA120408-DIA 0.031" 1 0.110" 䖃

DNGA 431 DIA DNGA150404-DIA 0.016" 1 0.122" 䖃 䖃

General
purpose DNGA 432 DIA DNGA150408-DIA 0.031" 1 0.110" 䖃

General SNGA 431 DIA SNGA120404-DIA 0.016" 1 0.142" 䖃

purpose 0.142" 䖃
SNGA 432 DIA SNGA120408-DIA 0.031" 1

General
SNGN 432 DIA SNGN120408-DIA 0.031" 1 0.142" 䖃
purpose

TNGA 331 DIA TNGA160404-DIA 0.016" 1 0.126" 䖃 䖃

General
purpose TNGA 332 DIA TNGA160408-DIA 0.031" 1 0.114" 䖃 䖃

䖃㻌: Line up

Reference pages
External toolholders → B208 -  Internal toolholders → B321 -
J series toolholders → B376 -  TungCap → B223 -, F006 -

B178 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - PCD Inse r t H : Heavy interrupted cutting

Posi ti ve i nser t (wi t h rake ang l e)

Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous CL
S Superalloys
H Hard materials

Length
Corner

corner
radius

No. of

Relief
angle

DIA

DX120
Specification Shape Designation

Inch Metric
CCMT 21.50.5-DIA CCMT060202-DIA 0.008" 1 7° 0.094" 䖃
Low cutting CCMT 21.51-DIA CCMT060204-DIA 0.016" 1 7° 0.094" 䖃
force CCMT 32.50.5-DIA CCMT09T302-DIA 0.008" 1 7° 0.138" 䖃
CCMT 32.51-DIA CCMT09T304-DIA 0.016" 1 7° 0.138" 䖃
DCMT 21.50.5-DIA DCMT070202-DIA 0.008" 1 7° 0.091" 䖃
Low cutting DCMT 21.51-DIA DCMT070204-DIA 0.016" 1 7° 0.083" 䖃
force DCMT 32.50.5-DIA DCMT11T302-DIA 0.008" 1 7° 0.126" 䖃

PCD / CBN
DCMT 32.51-DIA DCMT11T304-DIA 0.016" 1 7° 0.118" 䖃
TCMT 630.5-DIA TCMT080202-DIA 0.008" 1 7° 0.094" 䖃
TCMT 631-DIA TCMT080204-DIA 0.016" 1 7° 0.091" 䖃
Low cutting TCMT 21.50.5-DIA TCMT110202-DIA 0.008" 1 7° 0.094" 䖃
force TCMT 21.51-DIA TCMT110204-DIA 0.016" 1 7° 0.087" 䖃
TCMT 220.5-DIA TCMT110302-DIA 0.008" 1 7° 0.094" 䖃
TCMT 221-DIA TCMT110304-DIA 0.016" 1 7° 0.087" 䖃
Low cutting VCMT 330.5-DIA VCMT160402-DIA 0.008" 1 7° 0.189" 䖃
force VCMT 331-DIA VCMT160404-DIA 0.016" 1 7° 0.173" 䖃

Posi ti ve i nser t
P Steel
M Stainless
K Cast iron
N Non-ferrous CL CL CL
S Superalloys
H Hard materials
Length
Corner

corner
radius

No. of

Relief
angle

DIA

DX160
DX120
DX140

Specification Shape Designation

Inch Metric
CCGW 21.5V-DIA CCGW060200-DIA 0.002" 1 7° 0.094" 䖃
CCGW 21.50.5-DIA CCGW060202-DIA 0.008" 1 7° 0.094" 䖃
General CCGW 21.51-DIA CCGW060204-DIA 0.016" 1 7° 0.094" 䖃
purpose CCGW 32.50.5-DIA CCGW09T302-DIA 0.008" 1 7° 0.138" 䖃
CCGW 32.51-DIA CCGW09T304-DIA 0.016" 1 7° 0.138" 䖃 䖃
CCGW 32.52-DIA CCGW09T308-DIA 0.031" 1 7° 0.134" 䖃
DCGW 21.5V-DIA DCGW070200-DIA 0.002" 1 7° 0.094" 䖃
DCGW 21.50.5-DIA DCGW070202-DIA 0.008" 1 7° 0.091" 䖃 䖃
General DCGW 21.51-DIA DCGW070204-DIA 0.016" 1 7° 0.083" 䖃
purpose DCGW 32.50.5-DIA DCGW11T302-DIA 0.008" 1 7° 0.126" 䖃
DCGW 32.51-DIA DCGW11T304-DIA 0.016" 1 7° 0.118" 䖃
DCGW 32.52-DIA DCGW11T308-DIA 0.031" 1 7° 0.106" 䖃
SPGN 322-DIA SPGN090308-DIA 0.031" 1 11° 0.142" 䖃
General SPGN 420.5-DIA SPGN120302-DIA 0.008" 1 11° 0.142" 䖃
purpose SPGN 421-DIA SPGN120304-DIA 0.016" 1 11° 0.142" 䖃
SPGN 422-DIA SPGN120308-DIA 0.031" 1 11° 0.142" 䖃 䖃

䖃㻌: Line up
Reference pages
External toolholders → B228 - Internal toolholders → B299 -
J series toolholders → B362 - TungCap → F011 -

Tungaloy B179
 C : Continuous cutting
L : Light interrupted cutting
Tur nL in e - PCD Inse r t H : Heavy interrupted cutting

Posi t i ve i ns er t
Insert
P Steel
M Stainless
K Cast iron
N Non-ferrous CL CL
S Superalloys
H Hard materials

Length
Corner

corner
radius

No. of

Relief
angle

DIA

DX120
DX140
Specification Shape Designation

Inch Metric

CPGA 31.50.5-DIA CPGA090202-DIA 0.008" 1 11° 0.094" 䖃

General
purpose CPGA 31.51-DIA CPGA090204-DIA 0.016" 1 11° 0.094" 䖃

EPGW 520.5-DIA EPGW040102-DIA 0.008" 1 11° 0.075" 䖃

General
purpose EPGW 521-DIA EPGW040104-DIA 0.016" 1 11° 0.075" 䖃

TPGA730.5-DIA TPGA090202-DIA 0.008" 1 11° 0.094" 䖃

䖃
PCD / CBN

TPGA731-DIA TPGA090204-DIA 0.016" 1 11° 0.087"

TPGA21.50.5-DIA TPGA110202-DIA 0.008" 1 11° 0.094" 䖃
TPGA21.51-DIA TPGA110204-DIA 0.016" 1 11° 0.087" 䖃
General TPGA220.5-DIA TPGA110302-DIA 0.008" 1 11° 0.094" 䖃
purpose TPGA221-DIA TPGA110304-DIA 0.016" 1 11° 0.087" 䖃
TPGA222-DIA TPGA110308-DIA 0.031" 1 11° 0.114" 䖃
TPGA320.5-DIA TPGA160302-DIA 0.008" 1 11° 0.130" 䖃
TPGA321-DIA TPGA160304-DIA 0.016" 1 11° 0.126" 䖃
TPGA322-DIA TPGA160308-DIA 0.031" 1 11° 0.114" 䖃
TPGN 731-DIA TPGN090204-DIA 0.016" 1 11° 0.087" 䖃
TPGN 221-DIA TPGN110304-DIA 0.016" 1 11° 0.126" 䖃 䖃
General TPGN 222-DIA TPGN110308-DIA 0.031" 1 11° 0.114" 䖃
purpose TPGN 320.5-DIA TPGN160302-DIA 0.008" 1 11° 0.130" 䖃
TPGN 321-DIA TPGN160304-DIA 0.016" 1 11° 0.126" 䖃 䖃
TPGN 322-DIA TPGN160308-DIA 0.031" 1 11° 0.114" 䖃
TPGW 630.5-DIA TPGW080202-DIA 0.008" 1 11° 0.094" 䖃
TPGW 631-DIA TPGW080204-DIA 0.016" 1 11° 0.091" 䖃
TPGW 730.5-DIA TPGW090202-DIA 0.008" 1 11° 0.094" 䖃 䖃
TPGW 731-DIA TPGW090204-DIA 0.016" 1 11° 0.087" 䖃
TPGW 21.50.5-DIA TPGW110202-DIA 0.008" 1 11° 0.094" 䖃 䖃
General
TPGW 21.51-DIA TPGW110204-DIA 0.016" 1 11° 0.087" 䖃
purpose
TPGW 2.520.5-DIA TPGW130302-DIA 0.008" 1 11° 0.130" 䖃 䖃
TPGW 2.521-DIA TPGW130304-DIA 0.016" 1 11° 0.126" 䖃
TPGW 32.50.5-DIA TPGW16T302-DIA 0.008" 1 11° 0.130" 䖃
TPGW 32.51-DIA TPGW16T304-DIA 0.016" 1 11° 0.126" 䖃
TPGW 32.52-DIA TPGW16T308-DIA 0.031" 1 11° 0.114" 䖃

General VCGW 330.5-DIA VCGW160402-DIA 0.008" 1 7° 0.189" 䖃

purpose VCGW 331-DIA VCGW160404-DIA 0.016" 1 7° 0.173" 䖃

䖃㻌: Line up

Reference pages
External toolholders → B258 - Internal toolholders → B302 -

B180 www.tungaloyamerica.com
 Insert
MEMO

PCD / CBN

Tungaloy B181
Tur nLine - E x te r na l Toolholde r
Inch Metric

B19 0
Economical double-sided inserts with excellent sharpness

B2 02
Small-sized “Eco” insert series for maximized profits

B2 0 8
Highly rigid clamping system with excellent repeatability

B218
Toolholders for high pressure coolant supply

B231
Inserts with 25° corner angle for profiling

ISO-Turn External B23 3

Toolholders for general external turning
D-type, H-type, M-type, P-type, S-type, T-type

B2 6 9
Highly productive round insert with 6 indexes

B271
Ceramic insert with dimple for highly efficient cast iron machining

B275
Tool series for high-feed cutting

B276
Inserts and toolholders for roughing large depths of cut with high productivity

B182 www.tungaloyamerica.com
I S O - Ec oTu r n

Tungaloy B183
 E x ternal Toolholder (Negative inser t) - Quick Guide
Ext. Toolholder
Tu r n i n g / Fa c i n g External profiling Tu r n i n g

L 95o J 93o N 63o V 72.5o P 62.5o A 91o G 91o

80 o CN†† 70 o GN†† 55 o DN†† 35 o VN†† 35 o VN†† 55 o DN†† 60 o TN††

Double clamping

ACLNR/L ACLNR/L ADJNR/L AVJNR/L AVVNN ADPNN ATGNR/L

Turning A

B202, B208 B208 B204, B210 B207, B211 B208, B212 B212 B213

80 o WN†† 60 o TN†† 25 o YNMG 25 o YNMG

AWLNR/L ATJNR/L AVJNR/L AVVNN
B202, B210 B211 B211 B212

80 o CN†† 70 o GN†† 55 o DN†† 60 o TN††

DCLNR/L DCLNR/L DDJNR/L DTGNR/L
One-Double

B233 B233 B234 B234

D

80 o WN††
DWLNR/L
B233
dimple ceramic insert

80 o CN†† 55 o DN†† 55 o DNGD 35 o VNGD

Double clamping for

CCLNR/L CDJNR/L CDNNN CVVNN

B271 B271 B272 B272
C

80 o CN†† 70 o GN†† 55 o DN†† 55 o DN†† 60 o TN††

PCLNR/L PCLNR/L PDJNR/L PDMNL PTGNR/L
B203, B218, B223, B203, B218, B223, B205, B219, B223, B226 B206, B220, B240
B238, B376 B238, B376 B239, B376

80 o CN†† 70 o GN†† 35 o VN†† 55 o DN††

Lever lock

PCMNN PCMNN PVJNR/L PDPNN

B225 B225 B221, B224 B240
P

80 o CN†† 70 o GN†† 25 o YNMG

PCL2NR PCL2NR PVJNR/L
B376 B376 B221, B224

80 o WN†† 60 o TN††
PWLNR/L PTL2NR/L
B204, B222, B224 B239, B378

80 o CN†† 70 o GN†† 35 o VN†† 55 o DN†† 35 o VN†† 55 o DN††

MCLNR/L MCLNR/L MVJNR/L MDJNR/L MVVNN MDPNN
B246 B246 B247 B247 B248 B249
Multi clamping

80 o CN†† 80 o WN†† 25 o YNMG 55 o DN†† 25 o YNMG 55 o DN††

M

MCLNR/L MWLNR/L MVJNR/L MDJNR/L MVVNN MDPNN

B246 B246 B247 B247 B248 B249

60 o TN†† 60 o TN††
MTJNR/L MTJNR/L
B248 B248

55 o 60 o
Clamp-

KNMX TN††
on
C

CKJNR/L CTGNR/L
B256 B256
Retract-
pin
H
clamping

60 o TN†† 60 o TN††
Back
JT

JTTLNR/L JTTANR/L
B377 B377

The page number for the product details is shown in red.

B184 www.tungaloyamerica.com
 Tu r n i n g c h a m f e r i n g Turning/Facing External

Ext. Toolholder
Tu r n i n g Fa c i n g Profiling
chamfering profiling
B.R 75o E 60o D 45o S 45o K 75o F 91o Q *1 . H*1 45o Special

90 o SN†† 90o SN†† 90o SN†† 90o SN†† 60o TN†† 55o DN†† 35o VN†† - RN††
ASBNR/L ASDNN ASSNR/L ASKNR/L ATFNR/L ADQNR/L AVQNR/L ARGNR/L
B213 B214 B214 B215 B215 B206, B216 B207, B217 B217

80 o CN†† 80 o CN†† 60o TN†† 25o YNMG

ACRNR/L ACKNR/L ATQNR/L AVQNR/L
B209 B209 B216 B217

90 o SN†† 90o SN†† 90o SN†† 90o SN†† 60o TN†† 55o DN†† - RN††
DSBNR/L DSDNN DSSNR/L DSKNR/L DTFNR/L DDQNR/L DRGNR/L
B235 B235 B235 B236 B236 B237 B237

90o SNGD
CSSNR/L
B273

90o HNGD
CHSNR/L
B273

90 o SN†† 90o SN†† 90o SN†† 90o SN†† 60o TN†† 55o DN†† - RNMG
PSBNR/L PSDNN PSSNR/L PSKNR/L PTFNR/L PDQNR/L PRGNR/L
B241 B242 B242 B243 B243 B244 B244

100o CN†† 80o CN†† 35o VN††

PCBNR/L PCFNR/L PVQNR/L
B241 B244 B221

25o YNMG
PVQNR/L
B221

60o TN†† 35o VN††

MTENN MVQNR/L
B249 B250

25o YNMG
MVQNR/L
B250

60o TN††
MTQNR/L
B250

90 o SN†† 90o SN†† 90o SN†† 90o SN†† 60o TN††

CSBNR/L CSDNN CSSNR/L CSKNR/L CTFNR/L
B256 B257 B257 B257 B258

90 o SNMM
HSRNR/L
B260

Note:*1 marked Q and H style are Tungaloy Standard.

Tungaloy B185
 E x ter nal Toolholder (Positive inser t) - Q uick Guide
Tu r n i n g Tu r n i n g
Ext. Toolholder
External profiling Tu r n i n g
Fa c i n g Fa c i n g
L 95o J 93o V 72.5o N 62.5o A 91o G 91o B.R 75o X 20o

screw-on/clamping

80o
clamping

WPMT
Double

XWXPR/L
X

B275

80 o WXGU 55 o DXGU 35 o VXGU

JPWL2XR/L JPDJ2XR/L JPVJ2XR/L
Lever lock

B190 B192 B194

P

60o 90o
Clamp-on

TP†† SP††
CTGPR/L CSBPR/L
C

B258 B258

80o CC†† 55o DC†† 55o DXGU 35o VB†† 55o DC†† 80o CC†† 80o CC††
JSCLCR/L JSDJCR/L JSDJXR JSVNBN JSDNCN JSCACL JSCGCR/L
B363 B367 B193 B374 B368 B364 B365
JSDJ2XR/L
B192, B193, B227

80o CC†† 55o DC†† 35o VXGU 55o DC†† 60o TC††
JSCL2CR/L*2 JSDJ2CR/L*2 JSVJXR JSDN3CR/L*3 JSTACR/L
B362 B228, B365, B367 B195 B368 B370
Screw-on

JSVJ2XR/L
B194, B195, B228
J

35o VP†† 35o VB†† 35o VB††

JSVL2PR/L JSVJBR/L JSVABR/L
B375 B371 B372

80o WXGU 35o VB††

JSWLXR JSVJ2BR/L
B191 B229, B371, B372
JSWL2XR/L
B190, B191, B227

80o CC†† 55o DC†† 35o VC†† 55o DC†† 60o TC††
SCLCR/L SDJCR/L SVVCN SDNCN STACR/L
B261 B261 B263 B262 B263

35o VC††
SVJCR/L
B262
Screw-on
S

25o YWMT
SYJBR/L
B231

80o CC†† 55o DC†† 60o TC††

clamping
Back
JT

JTCL2CR/L JTDJ2CR/L JTTACR/L

B362 B366 B370
Taper-lock
T

*2: L2 and J2: without offset *3

63°

The page number for the product details is shown in red.

B186 www.tungaloyamerica.com
 Tu r n i n g Turning / Facing

Ext. Toolholder
Fa c i n g Profiling
Chamfering Chamfering
D 45o S 45o F 91o C 90o Q*145o . H*117.5o H 100o I 76.5o P 117.5o

90o SP†† 90o SP†† 60o TP†† 60o TP††

CSDPN CSSPR/L CTFPR/L CTCPR/L
B259 B259 B259 B260

55o DC†† 35o VP††

JSDFCR/L JSVP2PR/L
B369 B375

90o SC†† 35o VC†† 25o YWMT 25o YWMT

SSDCN SVQCR/L SYHBR/L SYIBN
B266 B267 B232 B232

90o SP†† 55o DC††

SSDPN Tungaloy standard SDQCR/L
B266 B267

35o VCG†
SVHCR/L
B267

25o YWMT
SYQBR/L
B231

Note:*1 marked Q and H style are Tungaloy Standard.

Tungaloy B187
 E x ter nal Toolholder (Positive inser t) - Q uick Guide
External Back Fr o n t t u r n i n g /
Ext. Toolholder
profiling turning R e ve s e t u r n i n g
Special

screw-on/clamping
clamping
Double
X

- RCM†
PRGCR/L
B245
Lever lock
P

- RCM†
PRDCN
B245
Clamp-on
C

JXB JX††
JSXBR/L JSXGR/L
B380 B379, B396

55o DC††
JTB
JSK-SDUCL
JSTBR/L B369
Screw-on

B381
J

55o DXGU
JSK-TBL3
B381 JS-SDUXL
B196

J10E 35o VXGU

JSEGR/L JS-SVUXL
B383 B197

Note: Note:
- RCMT JSXBR /L t ype J S XG R / L t y p e i s a l s o
is also used for u s e d f o r J XG - t y p e
SRACR/L
J X T- t y p e grooving inser ts.
B264 threading
inserts.

- RCMT
SRGCR/L
B265, B269
Screw-on
S

- RCMT
SRDCN
B266, B269
clamping
Back
JT

- RT††
TRACN
Taper-lock

B268
T

- RT††
TRDCN
B268

The page number for the product details is shown in red.

B188 www.tungaloyamerica.com
 Ext. Toolholder
MEMO

Tungaloy B189
Ext. Toolholder JSW L2XR /L
S c re w - o n to o l h o l d e r w i t h o u t o f f s e t w i t h 9 5 ° a p p ro a c h a n g l e , f o r W XG U i n s e r t s

95° L1 Without offset

L2

b
95°

h1

h
Cutting edge style L2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSWL2XR/L062 0.375 0.375 4.750 0.500 0.375 0 0.008 WXGU22**L/R... 0.66
JSWL2XR/L082 0.500 0.500 4.750 0.500 0.500 0 0.008 WXGU22**L/R... 0.66
JSWL2XR/L102 0.625 0.625 4.750 0.500 0.625 0 0.008 WXGU22**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JSWL2XR/L1010X04 10 10 120 11 10 0 0.2 WXGU0403**L/R... 0.9
JSWL2XR/L1212F04 12 12 85 11 12 0 0.2 WXGU0403**L/R... 0.9
JSWL2XR/L1212X04 12 12 120 11 12 0 0.2 WXGU0403**L/R... 0.9
JSWL2XR/L1616X04 16 16 120 13 16 0 0.2 WXGU0403**L/R... 0.9
JSWL2XR/L2020H04 20 20 100 13 20 0 0.2 WXGU0403**L/R... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Wrench
JSWL2XR/L... SR34-514 T-7F

JP W L2X R /L
Le v e r l o c k to o l h o l d e r w i t h o u t o f f s e t w i t h 9 5 ° a p p ro a c h a n g l e , f o r W XG U i n s e r t s

95° L1 Without offset

L2
b
f

95°
h1

Cutting edge style L2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JPWL2XR/L062 0.375 0.375 4.750 0.500 0.375 0 0.008 WXGU22**L/R... 0.66
JPWL2XR/L082 0.500 0.500 4.750 0.500 0.500 0 0.008 WXGU22**L/R... 0.66
JPWL2XR/L102 0.625 0.625 4.750 0.500 0.625 0 0.008 WXGU22**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JPWL2XR/L1010X04 10 10 120 11 10 0 0.2 WXGU0403**L/R... 0.9
JPWL2XR/L1212F04 12 12 85 11 12 0 0.2 WXGU0403**L/R... 0.9
JPWL2XR/L1212X04 12 12 120 11 12 0 0.2 WXGU0403**L/R... 0.9
JPWL2XR/L1616X04 16 16 120 13 16 0 0.2 WXGU0403**L/R... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Lever Pin Clamping screw Wrench
JPWL2XR/L... SLLV-2 SL-PI-2 SR10400611 HW2.0/5RED

Reference pages
JSWL2XR/L, JPWL2XR/L: Inserts → B198 -, Standard cutting conditions → B201

B190 www.tungaloyamerica.com
J S W LXR -F

Ext. Toolholder
S c re w - o n s te p p e d - h e a d to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r W XG U i n s e r t s

L3
95°

f1
L2

b
f
95°
L1
L4

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSWLXR082-F10 0.500 0.625 4.750 0.500 1.125 0.750 0.500 0.625 1.000 0.008 WXGU22**L... 0.66
JSWLXR102-F10 0.625 0.750 4.750 0.500 1.125 0.750 0.625 0.625 1.000 0.008 WXGU22**L... 0.66

Metric h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSWLXR1016X04-F15 10 16 120 12 27 11 10 15 26 0.2 WXGU0403**L... 0.9
JSWLXR1216F04-F15 12 16 85 12 27 11 12 15 26 0.2 WXGU0403**L... 0.9
JSWLXR1216X04-F15 12 16 120 12 27 11 12 15 26 0.2 WXGU0403**L... 0.9
JSWLXR1620X04-F15 16 20 120 12 27 11 16 15 26 0.2 WXGU0403**L... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L).

SPARE PARTS
Designation Clamping screw Wrench
JSWLXR**-F... SR34-514 T-7F

J S W L2XR /L-C HP
Scre w -o n to o l h ol d er w i t ho ut o f f set w i t h 9 5 ° a p p roa c h a n gl e , f or W XG U i n s e r t s , w i t h c h a n n e l s f or h i gh
pre s s u re c o o l a n t

95° L1 Without offset

L2
f2
f

95°
h1

Cutting edge style L2 5/16”-24UNF

Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSWL2XR/L082-CHP 0.500 0.500 3.344 0.750 0.500 0 0.650 0.008 WXGU22**L/R... 0.66

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSWL2XR/L1212F04-CHP 12 12 85 18 12 0 16.5 0.2 WXGU0403**L/R... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSWL2XR/L**-CHP SR34-514 S-CU-CHP T-7F

Reference pages
JSWLXR-F, JSWL2XR/L-CHP: Inserts → B198, Standard cutting conditions → B201

Tungaloy B191
Ext. Toolholder JSD J2X R /L
S c re w - o n to o l h o l d e r w i t h o u t o f f s e t w i t h 9 3 ° a p p ro a c h a n g l e , f o r DXG U i n s e r t s

L1 Without offset
L2

b
30°
93°

h1

h
Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSDJ2XR/L062 0.375 0.375 4.750 0.625 0.375 0 0.008 DXGU22**L/R... 0.66
JSDJ2XR/L082 0.500 0.500 4.750 0.625 0.500 0 0.008 DXGU22**L/R... 0.66
JSDJ2XR/L102 0.625 0.625 4.750 0.625 0.625 0 0.008 DXGU22**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JSDJ2XR/L1010X07 10 10 120 14 10 0 0.2 DXGU0703**L/R... 0.9
JSDJ2XR/L1212F07 12 12 85 14 12 0 0.2 DXGU0703**L/R... 0.9
JSDJ2XR/L1212X07 12 12 120 14 12 0 0.2 DXGU0703**L/R... 0.9
JSDJ2XR/L1616X07 16 16 120 18 16 0 0.2 DXGU0703**L/R... 0.9
JSDJ2XR/L2020H07 20 20 100 18 20 0 0.2 DXGU0703**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Wrench
JSDJ2XR/L... SR34-514 T-7F

JP D J2XR /L
Le v e r l o c k to o l h o l d e r w i t h o u t o f f s e t w i t h 9 3 ° a p p ro a c h a n g l e , f o r DXG U i n s e r t s

L1 Without offset
L2
f

b
30°

93°
h1

Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JPDJ2XR/L062 0.375 0.375 4.750 0.625 0.375 0 0.008 DXGU22**L/R... 0.66
JPDJ2XR/L082 0.500 0.500 4.750 0.625 0.500 0 0.008 DXGU22**L/R... 0.66
JPDJ2XR/L102 0.625 0.625 4.750 0.625 0.625 0 0.008 DXGU22**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JPDJ2XR/L1010X07 10 10 120 14 10 0 0.2 DXGU0703**L/R... 0.9
JPDJ2XR/L1212F07 12 12 85 14 12 0 0.2 DXGU0703**L/R... 0.9
JPDJ2XR/L1212X07 12 12 120 14 12 0 0.2 DXGU0703**L/R... 0.9
JPDJ2XR/L1616X07 16 16 120 18 16 0 0.2 DXGU0703**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Lever Pin Clamping screw Wrench
JPDJ2XR/L... SLLV-2 SL-PI-2 SR10400611 HW2.0/5RED

Reference pages
JSDJ2XR/L, JPDJ2XR/L: Inserts → B199 -, Standard cutting conditions → B201

B192 www.tungaloyamerica.com
J S D JX R -F

Ext. Toolholder
S c re w - o n s te p p e d - h e a d to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r DXG U i n s e r t s

L3

f1
30°
L2

b
f
93°
L1
L4

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSDJXR082-F10 0.500 0.625 4.750 0.500 1.125 0.625 0.500 0.625 1.000 0.008 DXGU22**L... 0.66
JSDJXR102-F10 0.625 0.750 4.750 0.500 1.125 0.625 0.625 0.625 1.000 0.008 DXGU22**L... 0.66

Metric h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSDJXR1016X07-F15 10 16 120 12 27 14 10 15 26 0.2 DXGU0703**L... 0.9
JSDJXR1216F07-F15 12 16 85 12 27 14 12 15 26 0.2 DXGU0703**L... 0.9
JSDJXR1216X07-F15 12 16 120 12 27 14 12 15 26 0.2 DXGU0703**L... 0.9
JSDJXR1620X07-F15 16 20 120 12 27 14 16 15 26 0.2 DXGU0703**L... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L).

SPARE PARTS
Designation Clamping screw Wrench
JSDJXR**-F... SR34-514 T-7F

J S D J2X R /L-C H P
Scre w -o n to o l h ol d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e , f or DXG U i n s e r t s , w i t h c h a n n e l s f or h i gh
pre s s u re c o o l a n t

L1 Without offset
L2
f2
f

30°
93°
h1

Cutting edge style J2 5/16”-24UNF

Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2XR/L082-CHP 0.500 0.500 3.344 0.750 0.500 0 0.730 0.008 DXGU22**L/R... 0.66

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2XR/L1212F07-CHP 12 12 85 19 12 0 18.5 0.2 DXGU0703**L/R... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSDJ2XR/L**-CHP SR34-514 S-CU-CHP T-7F

Reference pages
JSDJXR-F, JSDJ2XR/L-CHP: Inserts → B199 -, Standard cutting conditions → B201

Tungaloy B193
Ext. Toolholder JSV J2XR /L
S c re w - o n to o l h o l d e r w i t h o u t o f f s e t w i t h 9 3 ° a p p ro a c h a n g l e , f o r V XG U i n s e r t s

Without offset

b
50°
L2
93° L1

h1

h
Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSVJ2XR/L067 0.375 0.375 4.750 0.669 0.375 0 0.008 VXGU73.5**L/R... 0.66
JSVJ2XR/L087 0.500 0.500 4.750 0.748 0.500 0 0.008 VXGU73.5**L/R... 0.66
JSVJ2XR/L107 0.625 0.625 4.750 0.748 0.625 0 0.008 VXGU73.5**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JSVJ2XR/L1010X09 10 10 120 17 10 0 0.2 VXGU09T2**L/R... 0.9
JSVJ2XR/L1212F09 12 12 85 19 12 0 0.2 VXGU09T2**L/R... 0.9
JSVJ2XR/L1212X09 12 12 120 19 12 0 0.2 VXGU09T2**L/R... 0.9
JSVJ2XR/L1616X09 16 16 120 19 16 0 0.2 VXGU09T2**L/R... 0.9
JSVJ2XR/L2020H09 20 20 100 19 20 0 0.2 VXGU09T2**L/R... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Wrench
JSVJ2XR/L... SR34-508 T-7F

JP VJ2X R /L
Le v e r l o c k to o l h o l d e r w i t h o u t o f f s e t w i t h 9 3 ° a p p ro a c h a n g l e , f o r V XG U i n s e r t s

Without offset
f

b
50°

L2
93° L1
h1

Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JPVJ2XR/L067 0.375 0.375 4.750 0.669 0.375 0 0.008 VXGU73.5**L/R... 0.66
JPVJ2XR/L087 0.500 0.500 4.750 0.748 0.500 0 0.008 VXGU73.5**L/R... 0.66
JPVJ2XR/L107 0.625 0.625 4.750 0.748 0.625 0 0.008 VXGU73.5**L/R... 0.66

Metric h b L1 L2 h1 f rε** Insert Torque*

JPVJ2XR/L1010X09 10 10 120 19 10 0 0.2 VXGU09T2**L/R... 0.9
JPVJ2XR/L1212F09 12 12 85 19 12 0 0.2 VXGU09T2**L/R... 0.9
JPVJ2XR/L1212X09 12 12 120 19 12 0 0.2 VXGU09T2**L/R... 0.9
JPVJ2XR/L1616X09 16 16 120 19 16 0 0.2 VXGU09T2**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Lever Pin Clamping screw Wrench
JPVJ2XR/L... SLLV-1 SL-PI-2 SR10400611 HW2.0/5RED

Reference pages
JSVJ2XR/L, JPVJ2XR/L: Inserts → B200, Standard cutting conditions → B201

B194 www.tungaloyamerica.com
J S V JXR -F

Ext. Toolholder
S c re w - o n s te p p e d - h e a d to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r V XG U i n s e r t s

L3

f1
50° L2

b
f
93°
L1
L4

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSVJXR087-F10 0.500 0.625 4.750 0.500 1.125 0.750 0.500 0.625 1.000 0.008 VXGU73.5**L... 0.66
JSVJXR107-F10 0.625 0.750 4.750 0.500 1.125 0.750 0.500 0.625 1.000 0.008 VXGU73.5**L... 0.66

Metric h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSVJXR1016X09-F15 10 16 120 12 27 19 10 15 26 0.2 VXGU09T2**L... 0.9
JSVJXR1216F09-F15 12 16 85 12 27 19 12 15 26 0.2 VXGU09T2**L... 0.9
JSVJXR1216X09-F15 12 16 120 12 27 19 12 15 26 0.2 VXGU09T2**L... 0.9
JSVJXR1620X09-F15 16 20 120 12 27 19 16 15 26 0.2 VXGU09T2**L... 0.9
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L).

SPARE PARTS
Designation Clamping screw Wrench
JSVJXR**-F... SR34-508 T-7F

J S V J2XR /L-C HP
Scre w -o n to o l h ol d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e , f or V XG U i n s e r t s , w i t h c ool a n t n oz l e f o r hig h
pre s s u re

L1 Without offset
L2
f2
f

50°
93°
h1

Cutting edge style J2 5/16”-24UNF

Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2XR/L087-CHP 0.500 0.500 4.750 0.748 0.500 0 0.531 0.008 VXGU73.5**L/R... 0.66

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2XR/L1212F09-CHP 12 12 85 20 12 0 13.5 0.2 VXGU09T2**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSVJ2XR/L**-CHP SR34-508 S-CU-CHP T-7F

Reference pages
JSVJXR-F, JSVJ2XR/L-CHP: Inserts → B200, Standard cutting conditions → B201

Tungaloy B195
Ext. Toolholder JS-S D U X L
S c re w - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r DXG U i n s e r t s

L1
25
20

s
øD
h

3.8
f
B
93°

b
Cutting edge style U Left hand (L) shown.

Inch øDs f L1 h b B rε** Insert Torque*

JS159F-SDUXL07 0.625 0.236 3.346 0.591 0.591 0.303 0.008 DXGU22**L... 0.66
JS19G-SDUXL07 0.750 0.236 3.543 0.709 0.709 0.366 0.008 DXGU22**L... 0.66
JS19X-SDUXL07 0.750 0.236 4.724 0.709 0.709 0.366 0.008 DXGU22**L... 0.66
JS254X-SDUXL07 1.000 0.394 4.724 0.945 0.945 0.492 0.008 DXGU22**L... 0.66

Metric øDs f L1 h b B rε** Insert Torque*

JS14H-SDUXL07 14 6 100 13 6.75 6.75 0.2 DXGU0703**L... 0.9
JS159F-SDUXL07 15.875 6 85 15 7.687 7.687 0.2 DXGU0703**L... 0.9
JS16F-SDUXL07 16 6 85 15 7.75 7.75 0.2 DXGU0703**L... 0.9
JS19G-SDUXL07 19.05 6 90 18 9.275 9.275 0.2 DXGU0703**L... 0.9
JS19X-SDUXL07 19.05 6 120 18 9.275 9.275 0.2 DXGU0703**L... 0.9
JS20G-SDUXL07 20 6 90 19 9.75 9.75 0.2 DXGU0703**L... 0.9
JS20X-SDUXL07 20 6 120 19 9.75 9.75 0.2 DXGU0703**L... 0.9
JS22X-SDUXL07 22 10 120 21 10.75 10.75 0.2 DXGU0703**L... 0.9
JS25H-SDUXL07 25 10 100 24 12.25 12.25 0.2 DXGU0703**L... 0.9
JS254X-SDUXL07 25.4 10 120 24 12.45 12.45 0.2 DXGU0703**L... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Left-hand toolholders (L) are used with left-hand inserts (L).

SPARE PARTS
Designation Clamping screw Wrench
JS**-SDUXL07 SR34-514 T-7F

Reference pages
JS-SDUXL: Inserts → B199 -, Standard cutting conditions → B201

B196 www.tungaloyamerica.com
J S-S VU XL

Ext. Toolholder
S c re w - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r V XG U i n s e r t s

L1
25
20

7.5

s
h

øD
f
B
93°

b
Cutting edge style U Left hand (L) shown.

Inch øDs f L1 h b B rε** Insert Torque*

JS159F-SVUXL09 0.625 0.394 3.346 0.591 0.591 0.303 0.008 VXGU73.5**L... 0.66
JS19G-SVUXL09 0.750 0.394 3.543 0.709 0.709 0.362 0.008 VXGU73.5**L... 0.66
JS19X-SVUXL09 0.750 0.394 4.724 0.709 0.709 0.362 0.008 VXGU73.5**L... 0.66
JS254X-SVUXL09 1.000 0.394 4.724 0.945 0.945 0.488 0.008 VXGU73.5**L... 0.66

Metric øDs f L1 h b B rε** Insert Torque*

JS159F-SVUXL09 15.875 10 85 15 7.7 7.7 0.2 VXGU09T2**L... 0.9
JS16F-SVUXL09 16 10 85 15 7.7 7.7 0.2 VXGU09T2**L... 0.9
JS19G-SVUXL09 19.05 10 90 18 9.2 9.2 0.2 VXGU09T2**L... 0.9
JS19X-SVUXL09 19.05 10 120 18 9.2 9.2 0.2 VXGU09T2**L... 0.9
JS20G-SVUXL09 20 10 90 19 9.7 9.7 0.2 VXGU09T2**L... 0.9
JS20X-SVUXL09 20 10 120 19 9.7 9.7 0.2 VXGU09T2**L... 0.9
JS22X-SVUXL09 22 10 120 21 10.7 10.7 0.2 VXGU09T2**L... 0.9
JS25H-SVUXL09 25 10 100 24 12.2 12.2 0.2 VXGU09T2**L... 0.9
JS254X-SVUXL09 25.4 10 120 24 12.4 12.4 0.2 VXGU09T2**L... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Left-hand toolholders (L) are used with left-hand inserts (L).

SPARE PARTS
Designation Clamping screw Wrench
JS**-SVUXL09 SR34-508 T-7F

Reference pages
JS-SVUXL: Inserts → B200, Standard cutting conditions → B201

Tungaloy B197
 C : Continuous cutting
L : Light interrupted cutting
Ext. Toolholder INSERT H : Heavy interrupted cutting
P Steel L CL CL CL
POSITIVE TYPE M Stainless L CL
D OU B LE-S I DED K Cast iron L CL CL C
N Non-ferrous C
Trigon, 80° S Superalloys C C
with hole H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
SH725
Inch Metric
(Low cutting force) force) (Sharp edge) medium cutting cutting (Sharp edge)
Finishing to medium

JTS WXGU 220 MFR-JTS WXGU040301MFR-JTS <0.004"* 䖃

WXGU 220 MFL-JTS WXGU040301MFL-JTS <0.004"* 䖃

WXGU 220.5 MFR-JTS WXGU040302MFR-JTS <0.008"* 䖃

WXGU 220.5 MFL-JTS WXGU040302MFL-JTS <0.008"* 䖃

JTS WXGU 220 MR-JTS WXGU040301MR-JTS <0.004"* 䖃

Finishing to

WXGU 220 ML-JTS WXGU040301ML-JTS <0.004"* 䖃

WXGU 220.5 MR-JTS WXGU040302MR-JTS <0.008"* 䖃

WXGU 220.5 ML-JTS WXGU040302ML-JTS <0.008"* 䖃
Finishing (Low cutting

JSS WXGU 220 MFR-JSS WXGU040301MFR-JSS <0.004"* 䖃

WXGU 220 MFL-JSS WXGU040301MFL-JSS <0.004"* 䖃

WXGU 220.5 MFR-JSS WXGU040302MFR-JSS <0.008"* 䖃

WXGU 220.5 MFL-JSS WXGU040302MFL-JSS <0.008"* 䖃

JSS WXGU 220 MR-JSS WXGU040301MR-JSS <0.004"* 䖃

WXGU 220 ML-JSS WXGU040301ML-JSS <0.004"* 䖃
Finishing

WXGU 220.5 MR-JSS WXGU040302MR-JSS <0.008"* 䖃

WXGU 220.5 ML-JSS WXGU040302ML-JSS <0.008"* 䖃

TS WXGU 220.5 R TS WXGU040302R-TS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L TS WXGU040302L-TS 0.008" 䖃 䖃 䖃 䖃

medium cutting
Finishing to

WXGU 221 R TS WXGU040304R-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L TS WXGU040304L-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 222 R TS WXGU040308R-TS 0.031" 䖃 䖃 䖃 䖃

WXGU 222 L TS WXGU040308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force) Finishing (Wiper)

TSW WXGU 221 R TSW WXGU040304R-TSW 0.016" 䖃 䖃 䖃

WXGU 221 L TSW WXGU040304L-TSW 0.016" 䖃 䖃 䖃

WXGU 222 R TSW WXGU040308R-TSW 0.031" 䖃 䖃 䖃

WXGU 222 L TSW WXGU040308L-TSW 0.031" 䖃 䖃 䖃

SS WXGU 220.5 R SS WXGU040302R-SS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L SS WXGU040302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

WXGU 221 R SS WXGU040304R-SS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L SS WXGU040304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

䖃㻌: Line up

B198 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
INSERT H : Heavy interrupted cutting

Ext. Toolholder
P Steel L CL
POSITIVE TYPE M Stainless L CL
DO U B LE-S I D ED K Cast iron L
Rhombic, 55° N Non-ferrous
with hole S Superalloys C
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

AH725
SH725
Inch Metric
JRP DXGU 220-MFRE-JRP DXGU070301MFRE-JRP <0.004"* 䖃
(Sharp edge)

DXGU 220-MFLE-JRP DXGU070301MFLE-JRP <0.004"* 䖃

Finishing

DXGU 220.5-MFRE-JRP DXGU070302MFRE-JRP <0.008"* 䖃

DXGU 220.5-MFLE-JRP DXGU070302MFLE-JRP <0.008"* 䖃

䖃
Finishing (Low cutting Finishing to medium Finishing to medium
cutting (Sharp edge)

JTS DXGU 220-MFR-JTS DXGU070301MFR-JTS <0.004"*

DXGU 220-MFL-JTS DXGU070301MFL-JTS <0.004"* 䖃

DXGU 220.5-MFR-JTS DXGU070302MFR-JTS <0.008"* 䖃

DXGU 220.5-MFL-JTS DXGU070302MFL-JTS <0.008"* 䖃

JTS DXGU 220-MR-JTS DXGU070301MR-JTS <0.004"* 䖃

DXGU 220-ML-JTS DXGU070301ML-JTS <0.004"* 䖃
cutting

DXGU 220.5-MR-JTS DXGU070302MR-JTS <0.008"* 䖃

DXGU 220.5-ML-JTS DXGU070302ML-JTS <0.008"* 䖃

JSS DXGU 220-MFR-JSS DXGU070301MFR-JSS <0.004"* 䖃

force) (Sharp edge)

DXGU 220-MFL-JSS DXGU070301MFL-JSS <0.004"* 䖃

DXGU 220.5-MFR-JSS DXGU070302MFR-JSS <0.008"* 䖃

DXGU 220.5-MFL-JSS DXGU070302MFL-JSS <0.008"* 䖃

* Corner radius has minus tolerance.

䖃㻌: Line up

Tungaloy B199
 C : Continuous cutting
L : Light interrupted cutting
Ext. Toolholder H : Heavy interrupted cutting

P Steel L CL CL
POSITIVE TYPE
M Stainless L
D OU B LE-S I DED
K Cast iron L CL CL C
N Non-ferrous C
Rhombic, 55° S Superalloys C C
with hole H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
Inch Metric
(Low cutting force)

JSS DXGU 220 MR-JSS DXGU070301MR-JSS <0.004"* 䖃

DXGU 220 ML-JSS DXGU070301ML-JSS <0.004"* 䖃
Finishing

DXGU 220.5 MR-JSS DXGU070302MR-JSS <0.008"* 䖃

DXGU 220.5 ML-JSS DXGU070302ML-JSS <0.008"* 䖃

TS DXGU 220.5 TS DXGU070302R-TS 0.008" 䖃 䖃 䖃 䖃

Finishing to medium

DXGU 220.5 TS DXGU070302L-TS 0.008" 䖃 䖃 䖃 䖃

DXGU 221 TS DXGU070304R-TS 0.016" 䖃 䖃 䖃 䖃

cutting

DXGU 221 TS DXGU070304L-TS 0.016" 䖃 䖃 䖃 䖃

DXGU 222 TS DXGU070308R-TS 0.031" 䖃 䖃 䖃 䖃

DXGU 222 TS DXGU070308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force)

SS DXGU 220.5 SS DXGU070302R-SS 0.008" 䖃 䖃 䖃 䖃

DXGU 220.5 SS DXGU070302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

DXGU 221 SS DXGU070304R-SS 0.016" 䖃 䖃 䖃 䖃

DXGU 221 SS DXGU070304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

P Steel CL
POSITIVE TYPE M Stainless CL
D OU B LE-S I DED K Cast iron
N Non-ferrous
Rhombic, 35° S Superalloys
with hole H Hard materials
Coated
Application

Corner
radius

Chipbreaker Designation
SH725

Inch Metric

JRP VXGU 73.50 MFRE-JRP VXGU09T201MFRE-JRP <0.004"* 䖃

(Sharp edge)

VXGU 73.50 MFLE-JRP VXGU09T201MFLE-JRP <0.004"* 䖃

Finishing

VXGU 73.50.5 MFRE-JRP VXGU09T202MFRE-JRP <0.008"* 䖃

VXGU 73.50.5 MFLE-JRP VXGU09T202MFLE-JRP <0.008"* 䖃

* Corner radius has minus tolerance. 䖃㻌: Line up

B200 www.tungaloyamerica.com
 STAN DAR D CUT T ING CONDIT IONS

Ext. Toolholder
F O R E X T E RNAL T U R N IN G

Cutting Depth of
Chip- Feed
Applications ISO Workpiece material Priority Grade speed cut
breaker f (ipr)
Vc (sfm) ap (in)

Low carbon steels With high

JSS SH725 160 - 590 0.004 - 0.060 0.001 - 0.004
Carbon steels (1045, etc.) sharpness
Low alloy steels
For swiss Alloy steels (4140, etc.) First choice JTS AH725 160 - 590 0.004 - 0.080 0.001 - 0.004
type
automatic Stainless steels (Austenitic)
lathes (304, etc.) First choice JSS SH725 160 - 590 0.004 - 0.060 0.001 - 0.004
Stainless steels (Martensitic and ferritic)
(430, etc.)
Stainless steels (Precipitation hardened) For impact
JTS AH725 160 - 590 0.004 - 0.080 0.001 - 0.004
(174, etc.) resistance

SS AH725 160 - 590 0.006 - 0.060 0.002 - 0.008

First choice
TS AH725 160 - 590 0.012 - 0.080 0.003 - 0.012
Low carbon steels
Carbon steels (1045, etc.) For improved SS NS9530 260 - 660 0.006 - 0.060 0.002 - 0.008
Low alloy steels surface finish TS NS9530 260 - 660 0.012 - 0.080 0.003 - 0.012
For small Alloy steels (4140, etc.)
For wear SS GT9530 260 - 820 0.006 - 0.060 0.002 - 0.008
size CNC
resistance TS GT9530 260 - 820 0.012 - 0.080 0.003 - 0.012
lathes
Stainless steels (Austenitic)
(304, etc.) First choice SS AH725 160 - 490 0.006 - 0.060 0.002 - 0.008
Stainless steels (Martensitic and ferritic)
(430, etc.)
Stainless steels (Precipitation hardened) For impact
TS AH725 160 - 490 0.012 - 0.080 0.003 - 0.012
(174, etc.) resistance

Tungaloy B201
Ext. Toolholder AC LN R /L-Eco
D o u b l e - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ACLNR/L1233-A 0.750 0.750 4.500 0.900 0.750 1.000 0.625 0.031 CN**33... 2.2
ACLNR/L1633-A 1.000 1.000 6.000 1.000 1.000 1.250 0.750 0.031 CN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ACLNR/L2020K0904-A 20 20 125 25 20 25 18 0.8 CN**0904... 3
ACLNR/L2525M0904-A 25 25 150 25 25 32 18 0.8 CN**0904... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ACLNR/L**-A ACP3S-E ACS-5W BP-7 SP-2.5 ASC322 CSTB-3.5 T-15F

AW LN R /L-E c o
D o u b l e - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i g o n i n s e r t s

95°

b
f

L2
f2

L1
95°
h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

AWLNR/L1233-A 0.750 0.750 4.500 1.125 0.750 1.000 0.625 0.031 WN**33... 2.2
AWLNR/L1633-A 1.000 1.000 6.000 1.125 1.000 1.250 0.875 0.031 WN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

AWLNR/L2020K0604-A 20 20 125 27 20 25 16 0.8 WN**0604... 3
AWLNR/L2525M0604-A 25 25 150 27 25 32 23 0.8 WN**0604... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AWLNR/L**-A ACP3S-E ACS-5W BP-7 SP-2.5 ASW322 CSTB-3.5 T-15F

Reference pages
ACLNR/L-Eco: Inserts → B052 -
AWLNR/L-Eco: Inserts → B097 -

B202 www.tungaloyamerica.com
P C LN R /L-Eco

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er w i t h 9 5 ° ap p ro ach a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s

95°

b
f
L2

f2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L1233 0.750 0.750 4.500 0.813 0.750 1.000 0.625 0.031 CN**33... 1.5
PCLNR/L1633 1.000 1.000 6.000 0.813 1.000 1.250 0.750 0.031 CN**33... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L2020K0904 20 20 125 20 20 25 15 0.8 CN**0904... 2
PCLNR/L2525M0904 25 25 150 25 25 32 18 0.8 CN**0904... 2

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PCLNR/L** LSC317 LCS3 P-2.5 LSP3 LCL33

PC LN R /L-C H P- Eco
Le v e r l o c k t y p e to o l ho l d er w i t h 9 5 ° ap p ro ach a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s w i t h c h a n n e l s fo r
h ig h p re s s u re c o o l ant
L1
95°
L2
f2

b
f

95°
h1

Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L1233-CHP 0.750 0.750 4.500 1.300 0.750 1.250 0.750 0.031 CN**33... 1.5
PCLNR/L1633-CHP 1.000 1.000 6.000 0.813 1.000 1.250 0.750 0.031 CN**33... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L2020K0904-CHP 20 20 125 33 20 32 18 0.8 CN**0904... 2
PCLNR/L2525M0904-CHP 25 25 150 33 25 32 18 0.8 CN**0904... 2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PCLNR/L**-CHP LSC317 LCS3 P-2.5 LSP3 LCL33

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PCLNR/L**-CHP CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2

Reference pages
PCLNR/L-Eco, PCLNR/L-CHP-Eco: Inserts → B052 -

Tungaloy B203
Ext. Toolholder P W LN R /L-E c o
Le v e r l o c k t y pe to o l ho l d er w i t h 9 5 ° ap p roa c h a n gl e , f or n e ga t i v e 80° t r i gon i n s e r t s

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PWLNR/L1233 0.750 0.750 4.500 0.625 0.750 1.000 0.688 0.031 WN**33... 1.5
PWLNR/L1633 1.000 1.000 6.000 0.719 1.000 1.250 0.750 0.031 WN**33... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PWLNR/L2020K0604 20 20 125 15 20 25 18 0.8 WN**0604... 2
PWLNR/L2525M0604 25 25 150 19 25 32 20 0.8 WN**0604... 2

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PWLNR/L.... LSW312 LCS3 P-2.5 LSP3 LCL3

A D JN R /L-Eco
D o u b l e - c l a m p to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

b
f

L2
f2

L1
30°

93°
h1

Cutting edge style J h Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ADJNR/L1233-A 0.750 0.750 4.500 1.250 0.750 1.000 0.625 0.031 DN**33... 2.2
ADJNR/L1633-A 1.000 1.000 6.000 1.250 1.000 1.250 0.900 0.031 DN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ADJNR/L2020K1104-A 20 20 125 30 20 25 16 0.8 DN**1104... 3
ADJNR/L2525M1104-A 25 25 150 30 25 32 19 0.8 DN**1104... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ADJNR/L**-A ACP3S-E ACS-5W BP-7 SP-2.5 ASD322 CSTB-3.5 T-15F

Reference pages
PWLNR/L-Eco: Inserts → B097 -
ADJNR/L-Eco: Inserts → B063 -

B204 www.tungaloyamerica.com
PD JN R /L-Eco

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er w i t h 9 3 ° ap p ro ach a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
f
f2
L2

30°
L1
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PDJNR/L1033 0.625 0.625 4.000 1.125 0.625 0.875 0.625 0.031 DN**33... 1.5
PDJNR/L1233 0.750 0.750 4.500 1.125 0.750 1.000 0.625 0.031 DN**33... 1.5
PDJNR/L1633 1.000 1.000 6.000 1.125 1.000 1.250 0.750 0.031 DN**33... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PDJNR/L1616H1104 16 16 100 27 16 20 16 0.8 DN**1104... 2
PDJNR/L2020K1104 20 20 125 27 20 25 16 0.8 DN**1104... 2
PDJNR/L2525M1104 25 25 150 27 25 32 19 0.8 DN**1104... 2

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PDJNR/L... ELSD32 LCS3 P-2.5 LSP3 LCL33L

PD JN R /L-C H P- Eco
Le v e r l o c k t y p e to o l ho l d er w i t h 9 3 ° ap p ro ach a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s , w i t h c h a n n e l s fo r
h ig h p re s s u re c oo l ant

L1
L2
b
f
30°

93°
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

PDJNR/L1233-CHP  0.750 0.750 4.500 1.420 0.750 1.250 0.031 DN**33... 1.5
PDJNR/L1633-CHP 1.000 1.000 6.000 1.125 1.000 1.250 0.031 DN**33... 1.5

Metric h b L1 L2 h1 f rε** Insert Torque*

PDJNR/L2020K1104-CHP 20 20 125 36 20 32 0.8 DN**1104... 2
PDJNR/L2525M1104-CHP 25 25 150 36 25 32 0.8 DN**1104... 2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PDJNR/L**-CHP ELSD32 LCS3 P-2.5 LSP3 LCL33L

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PDJNR/L**-CHP CU-D-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2

Reference pages
PDJNR/L-Eco, PDJNR/L-CHP-Eco: Inserts → B063 -

Tungaloy B205
Ext. Toolholder P TG N R /L-Eco
Le v e r l o c k t y p e to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
f2
L2
91° L1

h1

h
Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PTGNR/L1223 0.750 0.750 4.500 0.750 0.750 1.000 0.625 0.031 TN**23... 1.5
PTGNR/L1623 1.000 1.000 6.000 0.750 1.000 1.250 0.875 0.031 TN**23... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PTGNR/L2020K1104 20 20 125 20 20 25 15 0.8 TN**1104... 2
PTGNR/L2525M1104 25 25 150 20 25 32 22.5 0.8 TN**1104... 2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench Lever
PTGNR/L... LCS23A P-2.5 LCL23

A D Q N R /L-E c o
Do u b l e -c l a m p to o l ho l d er w i t h 1 0 7 .5 ° ap p roa c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
107.5°
f

L2
f2

L1
107.5°
h1

h
Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ADQNR/L1233-A 0.750 0.750 4.500 1.150 0.750 1.000 0.750 0.031 DN**33... 2.2
ADQNR/L1633-A 1.000 1.000 6.000 1.150 1.000 1.250 0.800 0.031 DN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ADQNR/L2020K1104-A 20 20 125 30 20 25 18 0.8 DN**1104... 3
ADQNR/L2525M1104-A 25 25 150 30 25 32 20 0.8 DN**1104... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ADQNR/L**-A ACP3S-E ACS-5W BP-7 SP-2.5 ASD322 CSTB-3.5 T-15F

Reference pages
PTGNR/L-Eco: Inserts → B082 -
ADQNR/L-Eco: Inserts → B063 -

B206 www.tungaloyamerica.com
AV JN R /L-E co

Ext. Toolholder
D o u b l e - c l a m p to o l h o l d e r s – 9 3 ° a p p ro a c h a n g l e . Fo r n e g a t i v e 3 5 ° r h o m b i c i n s e r t .

b
f
L2

50°
L1
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

AVJNR/L122.33-A 0.750 0.750 4.500 1.500 0.750 1.000 0.031 VN**2.33**E... 2.2
AVJNR/L162.33-A 1.000 1.000 6.000 1.500 1.000 1.250 0.031 VN**2.33**E... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVJNR/L2020K1204-A 20 20 125 37 20 25 0.8 VN**1204... 3
AVJNR/L2525M1204-A 25 25 150 37 25 32 0.8 VN**1204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVJNR/L**-A ACP3L-E ACS-5W BP-7 SP-2.5 ASV222 CSTB-3.0 T-15F

AV QN R /L-Eco
D o u b l e - c l a m p to o l h o l d e r s – 1 1 7 . 5 ° a p p ro a c h a n g l e . Fo r n e g a t i v e 3 5 ° r h o m b i c i n s e r t .

b
f

117.5°
L2
L1
117.5°
h1

Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

AVQNR/L122.33-A 0.750 0.750 4.500 1.250 0.750 1.000 0.031 VN**2.33**E... 2.2
AVQNR/L162.33-A 1.000 1.000 6.000 1.250 1.000 1.250 0.031 VN**2.33**E... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVQNR/L2020K1204-A 20 20 125 32 20 25 0.8 VN**1204... 3
AVQNR/L2525M1204-A 25 25 150 32 25 32 0.8 VN**1204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVQNR/L**-A ACP3L-E ACS-5W BP-7 SP-2.5 ASV222 CSTB-3.0 T-15F

Reference pages
AVJNR/L-Eco, AVQNR/L-Eco: Inserts → B093 -

Tungaloy B207
Ext. Toolholder AV VN N -E co
D o u b l e - c l a m p to o l h o l d e r s – 7 2 . 5 ° a p p ro a c h a n g l e . Fo r n e g a t i v e 3 5 ° r h o m b i c i n s e r t .

b
L2
L1
72.5°

h1

h
Cutting edge style V Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

AVVNN122.33-A 0.750 0.750 4.500 1.500 0.750 0.375 0.031 VN**2.33**E... 2.2
AVVNN162.33-A 1.000 1.000 6.000 1.500 1.000 0.500 0.031 VN**2.33**E... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVVNN2020K1204-A 20 20 125 38 20 10 0.8 VN**1204... 3
AVVNN2525K1204-A 25 25 150 38 25 13 0.8 VN**1204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVVNN**-A ACP3L-E ACS-5W BP-7 SP-2.5 ASV222 CSTB-3.0 T-15F

AC LN R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

95°

b
f
f2

L2
L1
95°
h1

Cutting edge style L h Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ACLNR/L1233-A 0.750 0.750 4.500 0.900 0.750 1.000 0.625 0.031 CN**33... 2.2
ACLNR/L1633-A 1.000 1.000 6.000 1.000 1.000 1.250 0.750 0.031 CN**33... 2.2
ACLNR/L124-A 0.750 0.750 4.500 1.000 0.750 1.000 0.750 0.031 CN**43... 2.2
ACLNR/L164-A 1.000 1.000 6.000 1.250 1.000 1.250 0.875 0.031 CN**43... 2.2
ACLNR/L205-A 1.250 1.250 7.000 1.500 1.250 1.500 1.000 0.047 CN**54... 4.7
ACLNR/L245-A 1.500 1.500 8.000 1.500 1.500 1.750 1.125 0.047 CN**54... 4.7
ACLNR/L206-A 1.250 1.250 7.000 1.500 1.250 1.500 1.000 0.047 CN**64... 4.7
ACLNR/L246-A 1.500 1.500 8.000 1.500 1.500 1.750 1.125 0.047 CN**64... 4.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ACLNR/L2020K12-A 20 20 125 26 20 25 19 0.8 CN**1204... 3
ACLNR/L2525M12-A 25 25 150 30 25 32 21 0.8 CN**1204... 3
ACLNR/L3225P12-A 32 25 170 30 32 32 21 0.8 CN**1204... 3
ACLNR/L2525M16-A 25 25 150 31 25 32 22 1.2 CN**1606... 6.4
ACLNR/L3225P16-A 32 25 170 31 32 32 22 1.2 CN**1606... 6.4
ACLNR/L3232P16-A 32 32 170 31 32 40 22 1.2 CN**1606... 6.4
ACLNR/L3232P19-A 32 32 170 40 32 40 25 1.2 CN**1906... 6.4
ACLNR/L4040S19-A 40 40 250 40 40 50 25 1.2 CN**1906... 6.4
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench 1 Wrench 2
ACLNR/L**33-A ACP3S-E ACS-5W BP-7 SP-2.5 ASC322 CSTB-3.5 T-15F -
ACLNR/L**4-A,
ACP4S ACS-5W BP-7 SP-2.5 ASC422 CSTB-3.5 T-15F -
ACLNR/L**12-A
ACLNR/L**5-A,
ACP5S ACS-6W BP-8.8 SP-2.5 ASC533 CSTB-5 - KEYV-T20
ACLNR/L**16-A
ACLNR/L**6-A,
ACP6S ACS-6W BP-8.8 SP-2.5 ASC634 CSTB-5 - KEYV-T20
ACLNR/L**19-A

B208 www.tungaloyamerica.com
AC R N R /L

Ext. Toolholder
D o u b l e - c l a m p to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

b
f
75° L2
L1

h1

h
Cutting edge style R Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

ACRNR/L164-A 1.000 1.000 6.000 1.25 1.000 1.25 0.032 CN**43... 2.2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench 1
ACRNR/L164-A ACP4S ACS-5W BP-7 SP-2.5 ASC422 CSTB-3.5 T-15F

AC K N R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

b
f

L2
L1
h1

95°

h
Cutting edge style K Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ACKNR/L164-A 1.000 1.000 6.000 1.375 1.000 1.312 0.875 0.032 CN**43... 2.2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench 1
ACKNR/L164-A ACP4S ACS-5W BP-7 SP-2.5 ASC422 CSTB-3.5 T-15F

Reference pages
AVVNN-Eco: Inserts → B093 -
ACLNR/L, ACRNR/L, ACKNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178

Tungaloy B209
Ext. Toolholder AW LN R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i g o n i n s e r t s

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

AWLNR/L1233-A 0.750 0.750 4.500 1.125 0.750 1.000 0.625 0.031 WN**33... 2.2
AWLNR/L123-A 0.750 0.750 4.500 1.125 0.750 1.000 0.625 0.031 WN**33... 2.2
AWLNR/L1633-A 1.000 1.000 6.000 1.125 1.000 1.250 0.875 0.031 WN**33... 2.2
AWLNR/L163-A 1.000 1.000 6.000 1.125 1.000 1.250 0.875 0.031 WN**33... 2.2
AWLNR/L124-A 0.750 0.750 4.500 1.250 0.750 1.000 0.764 0.031 WN**43... 2.2
AWLNR/L164-A 1.000 1.000 6.000 1.250 1.000 1.250 0.875 0.031 WN**43... 2.2
AWLNR/L204-A 1.250 1.250 7.000 1.250 1.250 1.500 1.000 0.031 WN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

AWLNR/L2020K06-A 20 20 125 27 20 25 16 0.8 WN**0604... 3
AWLNR/L2020K08-A 20 20 125 30 20 25 19 0.8 WN**0804... 3
AWLNR/L2525M06-A 25 25 150 27 25 32 23 0.8 WN**0604... 3
AWLNR/L2525M08-A 25 25 150 30 25 32 21 0.8 WN**0804... 3
AWLNR/L3225P08-A 32 25 170 30 32 32 21 0.8 WN**0804... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AWLNR/L**3-A, 06-A ACP3S ACS-5W BP-7 SP-2.5 ASW322 CSTB-3.5 T-15F
AWLNR/L**4-A, 08-A ACP4S ACS-5W BP-7 SP-2.5 ASW422 CSTB-3.5 T-15F

A D JN R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s
b
f
f2

L2
30°

L1
93°
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ADJNR/L1233-A 0.750 0.750 4.500 1.250 0.750 1.000 0.625 0.031 DN**33... 2.2
ADJNR/L124-A 0.750 0.750 4.500 1.500 0.750 1.000 0.750 0.031 DN**43... 2.2
ADJNR/L1633-A 1.000 1.000 6.000 1.250 1.000 1.250 0.900 0.031 DN**33... 2.2
ADJNR/L164-A 1.000 1.000 6.000 1.500 1.000 1.250 0.750 0.031 DN**43... 2.2
ADJNR/L204-A 1.250 1.250 7.000 1.500 1.250 1.500 1.000 0.031 DN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ADJNR/L2020K15-A 20 20 125 36 20 25 17 0.8 DN**1504... 3
ADJNR/L2020K1506-A 20 20 125 36 20 25 17 0.8 DN**1506... 3
ADJNR/L2525M15-A 25 25 150 36 25 32 18 0.8 DN**1504... 3
ADJNR/L2525M1506-A 25 25 150 36 25 32 18 0.8 DN**1506... 3
ADJNR/L3225P15-A 32 25 170 36 32 32 18 0.8 DN**1504... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ADJNR/L**3-A, 15-A ACP4S ACS-5W BP-7 SP-2.5 ASD432 CSTB-3.5 T-15F
ADJNR/L**4-A, 1506-A ACP4S ACS-5W BP-7 SP-2.5 ASD423 CSTB-3.5 T-15F

B210 www.tungaloyamerica.com
AV JN R /L

Ext. Toolholder
Do u b l e -c l a m p to o l ho l d er w i t h 9 3 ° ap p ro ach a n gl e , f or n e ga t i v e 35° a n d 25° r h om b i c i n s e r t s

b
f
50°
L2
93° L1

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

AVJNR/L123-A 0.750 0.750 4.500 1.750 0.750 1.000 0.031 V/YN**33... 2.2
AVJNR/L163-A 1.000 1.000 6.000 1.870 1.000 1.250 0.031 V/YN**33... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVJNR/L2020K16-A 20 20 125 43 20 25 0.8 V/YN**1604... 3
AVJNR/L2525M16-A 25 25 150 46 25 32 0.8 V/YN**1604... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVJNR/L**3-A, 16-A ACP3L ACS-5W BP-7 SP-2.5 ASV322 CSTB-3.5 T-15F

ATJN R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
f2

L2
L1
93°
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ATJNR/L123-A 0.750 0.750 4.500 0.875 0.750 1.000 0.875 0.031 TN**33... 2.2
ATJNR/L163-A 1.000 1.000 6.000 0.875 1.000 1.250 1.000 0.031 TN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ATJNR/L2020K16-A 20 20 125 22 20 25 23 0.8 TN**1604... 3
ATJNR/L2525M16-A 25 25 150 22 25 32 25 0.8 TN**1604... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ATJNR/L**3-A, 16-A ACP3S ACS-5W BP-7 SP-2.5 AST322 CSTB-3.5 T-15F

Reference pages
AWLNR/L: Inserts → B097 -, CBN → B167
ADJNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
AVJNR/L: Inserts → B093 -, B104, CBN → B167, PCD → B178
ATJNR/L: Inserts → B082 -, CBN → B166, PCD → B178

Tungaloy B211
Ext. Toolholder AV VN N
Do u b l e -c l a m p to o l ho l d er w i t h 7 2 .5 ° ap p ro a c h a n gl e , f or n e ga t i v e 35° a n d 25° r h om b i c i n s e r t s

b
f
L2
L1
72.5°

h1

h
Cutting edge style V
Inch h b L1 L2 h1 f rε** Insert Torque*
AVVNN123-A 0.750 0.750 4.500 1.870 0.750 0.375 0.031 V/YN**33... 2.2
AVVNN163-A 1.000 1.000 6.000 1.870 1.000 0.500 0.031 V/YN**33... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVVNN2020K16-A 20 20 125 46 20 10 0.8 V/YN**1604... 3
AVVNN2525M16-A 25 25 150 46 25 12.5 0.8 V/YN**1604... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVVNN**3-A, 16-A ACP3L ACS-5W BP-7 SP-2.5 ASV322 CSTB-3.5 T-15F

A D PN N
Do u b l e -c l a m p to o l ho l d er w i t h 6 2 .5 ° ap p ro a c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s
f

L2
L1 b
62.5°
h1

Cutting edge style P

Inch h b L1 L2 h1 f rε** Insert Torque*
ADPNN124-A 0.750 0.750 4.500 1.500 0.750 0.375 0.031 DN**43... 2.2
ADPNN164-A 1.000 1.000 6.000 1.500 1.000 0.500 0.031 DN**43... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

ADPNN2020K15-A 20 20 125 36 20 7.5 0.8 DN**1504... 3
ADPNN2525M15-A 25 25 150 36 25 12.5 0.8 DN**1504... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ADPNN**4-A, 15-A ACP4S ACS-5W BP-7 SP-2.5 ASD432 CSTB-3.5 T-15F

Reference pages
AVVNN: Inserts → B093 -, B104, CBN → B167 -, PCD → B178
ADPNN: Inserts → B063 -, CBN → B165 -, PCD → B178
ATGNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178
ASBNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178

B212 www.tungaloyamerica.com
ATG N R /L

Ext. Toolholder
D o u b l e - c l a m p to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f2
f
L2
L1
91°

h1

h
Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ATGNR/L123-A 0.750 0.750 4.500 0.875 0.750 1.000 0.875 0.031 TN**33... 2.2
ATGNR/L163-A 1.000 1.000 6.000 0.875 1.000 1.250 1.000 0.031 TN**33... 2.2
ATGNR/L164-A 1.000 1.000 6.000 1.000 1.000 1.250 1.000 0.031 TN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ATGNR/L2020K16-A 20 20 125 22 20 25 22 0.8 TN**1604... 3
ATGNR/L2525M16-A 25 25 150 22 25 32 25 0.8 TN**1604... 3
ATGNR/L2525M22-A 25 25 150 26 25 32 26 0.8 TN**2204... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ATGNR/L**3-A, 16-A ACP3S ACS-5W BP-7 SP-2.5 AST322 CSTB-3.5 T-15F
ATGNR/L**4-A, 22-A ACP4S ACS-5W BP-7 SP-2.5 AST422 CSTB-3.5 T-15F

AS B N R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s
f

b 30

5
L2 17+0.5
0
75° L1

2020-type
h1

Cutting edge style B Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

ASBNR/L124-A 0.750 0.750 4.500 1.180 0.750 0.625 0.031 SN**43... 2.2
ASBNR/L164-A 1.000 1.000 6.000 1.180 1.000 0.875 0.031 SN**43... 2.2
ASBNR/L205-A 1.250 1.250 7.000 1.500 1.250 1.100 0.031 SN**54... 4.7
ASBNR/L245-A 1.500 1.500 8.000 1.500 1.500 1.350 0.031 SN**54... 4.7
ASBNR/L206-A 1.250 1.250 7.000 1.625 1.250 1.100 0.031 SN**64... 4.7
ASBNR/L246-A 1.500 1.500 8.000 1.625 1.500 1.350 0.031 SN**64... 4.7

Metric h b L1 L2 h1 f rε** Insert Torque*

ASBNR/L2020K12-A 20 20 125 30 20 17 0.8 SN**1204... 3
ASBNR/L2525M12-A 25 25 150 30 25 22 0.8 SN**1204... 3
ASBNR/L2525M15-A 25 25 150 42.5 25 22 1.2 SN**1506... 6.4
ASBNR/L3232P15-A 32 32 170 42.5 32 27 1.2 SN**1506... 6.4
ASBNR/L3232P19-A 32 32 170 47.5 32 27 1.2 SN**1906... 6.4
ASBNR/L4040S19-A 40 40 250 47.5 40 35 1.2 SN**1906... 6.4
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench 1 Wrench 2
ASBNR/L**4-A, 12-A ACP4S ACS-5W BP-7 SP-2.5 ASS422 CSTB-3.5 T-15F -
ASBNR/L**5-A, 15-A ACP5S ACS-6W BP-8.8 SP-2.5 ASS533 CSTB-5 - KEYV-T20
ASBNR/L**6-A, 19-A ACP6S ACS-6W BP-8.8 SP-2.5 ASS634 CSTB-5 - KEYV-T20

Tungaloy B213
Ext. Toolholder ASD N N
D o u b l e - c l a m p to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
f
45° L2
L1

h1

h
Cutting edge style D
Inch h b L1 L2 h1 f rε** Insert Torque*
ASDNN124-A 0.750 0.750 4.500 1.380 0.750 0.375 0.031 SN**43... 2.2
ASDNN164-A 1.000 1.000 6.000 1.380 1.000 0.500 0.031 SN**43... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

ASDNN2020K12-A 20 20 125 35 20 10 0.8 SN**1204... 3
ASDNN2525M12-A 25 25 150 35 25 12.5 0.8 SN**1204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ASDNN**4-A, 12-A ACP4S ACS-5W BP-7 SP-2.5 ASS422 CSTB-3.5 T-15F

ASSN R /L
Do u b l e -c l a m p to o l ho l d er w i t h 4 5 ° ap p ro ac h a n gl e (S - s t y l e ), f or n e ga t i v e s q u a re i n s e r t s

45°

b
f

L2
f2

45°
L1
h1

Cutting edge style S Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ASSNR/L124-A 0.750 0.750 4.500 1.250 0.750 1.000 0.327 0.031 SN**43... 2.2
ASSNR/L164-A 1.000 1.000 6.000 1.250 1.000 1.250 0.327 0.031 SN**43... 2.2
ASSNR/L205-A 1.250 1.250 7.000 1.500 1.250 1.500 - 0.031 SN**54... 4.7
ASSNR/L245-A 1.500 1.500 8.000 1.500 1.500 1.750 - 0.031 SN**54... 4.7
ASSNR/L206-A 1.250 1.250 7.000 1.500 1.250 1.500 - 0.031 SN**64... 4.7
ASSNR/L246-A 1.500 1.500 8.000 1.500 1.500 1.750 - 0.031 SN**64... 4.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ASSNR/L2020K12-A 20 20 125 30 20 25 8.3 0.8 SN**1204... 3
ASSNR/L2525M12-A 25 25 150 30 25 32 8.3 0.8 SN**1204... 3
ASSNR/L2525M15-A 25 25 150 25 25 32 10.3 1.2 SN**1506... 6.4
ASSNR/L3232P15-A 32 32 170 25 32 40 10.3 1.2 SN**1506... 6.4
ASSNR/L3232P19-A 32 32 170 27.5 32 40 12.5 1.2 SN**1906... 6.4
ASSNR/L4040S19-A 40 40 250 27.5 40 50 12.5 1.2 SN**1906... 6.4

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench 1 Wrench 2
ASSNR/L**4-A, 12-A ACP4S ACS-5W BP-7 SP-2.5 ASS422 CSTB-3.5 T-15F -
ASSNR/L**5-A, 15-A ACP5S ACS-6W BP-8.8 SP-2.5 ASS533 CSTB-5 - KEYV-T20
ASSNR/L**6-A, 19-A ACP6S ACS-6W BP-8.8 SP-2.5 ASS634 CSTB-5 - KEYV-T20

B214 www.tungaloyamerica.com
AS K N R /L

Ext. Toolholder
D o u b l e - c l a m p to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

75°

b
f2
20

4.5
L2

+0.5
L1

0
25
17
2020-type

h1

h
Cutting edge style K Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ASKNR/L124-A 0.750 0.750 4.500 0.875 0.750 1.000 0.750 0.031 SN**43... 2.2
ASKNR/L164-A 1.000 1.000 6.000 1.000 1.000 1.250 0.875 0.031 SN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ASKNR/L2020K12-A 20 20 125 20 20 25 17 0.8 SN**1204... 3
ASKNR/L2525M12-A 25 25 150 22 25 32 21 0.8 SN**1204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ASKNR/L**4-A, 12-A ACP4S ACS-5W BP-7 SP-2.5 ASS422 CSTB-3.5 T-15F

ATFN R /L
Do u b l e -c l a m p to o l ho l d er f o r f aci ng w i t h 9 1 ° a p p roa c h a n gl e , n e ga t i v e t r i a n gl e i n s e r t s

b
f
f2

91°
L2
L1
h1

Cutting edge style F Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ATFNR/L123-A 0.750 0.750 4.500 1.000 0.750 1.000 0.718 0.032 TN**33... 2.2
ATFNR/L163-A 1.000 1.000 6.000 1.000 1.000 1.250 0.750 0.032 TN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ATFNR/L2020K16-A 20 20 125 25 20 25 18 0.8 TN**1604... 3
ATFNR/L2525M16-A 25 25 150 25 25 32 19 0.8 TN**1604... 3
ATFNR/L2525M22-A 25 25 150 29 25 32 23 0.8 TN**2204... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ATFNR/L**3-A, 16-A ACP3S ACS-5W BP-7 SP-2.5 AST322 CSTB-3.5 T-15F
ATFNR/L**22-A ACP4S ACS-5W BP-7 SP-2.5 AST422 CSTB-3.5 T-15F

Reference pages
ASDNN, ASSNR/L: Inserts → B073 -, CBN → B166, PCD → B178
ASKNR/L: Inserts → B073 -, CBN → B166, PCD → B178
ATFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B215
Ext. Toolholder AD QN R /L
Do u b l e -c l a m p to o l ho l d er w i t h 1 0 7 .5 ° ap p roa c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
107.5°

f
f2
L2 L1

107.5°

h1

h
Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ADQNR/L124-A 0.750 0.750 4.500 1.250 0.750 1.000 - 0.031 DN**43... 2.2
ADQNR/L164-A 1.000 1.000 6.000 1.500 1.000 1.250 - 0.031 DN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ADQNR/L2020K15-A 20 20 125 32 20 25 21 0.8 DN**1504... 3
ADQNR/L2020K1506-A 20 20 125 32 20 25 21 0.8 DN**1506... 3
ADQNR/L2525M15-A 25 25 150 36 25 32 23 0.8 DN**1504... 3
ADQNR/L2525M1506-A 25 25 150 36 25 32 23 0.8 DN**1506... 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ADQNR/L**4-A, 15-A ACP4S ACS-5W BP-7 SP-2.5 ASD432 CSTB-3.5 T-15F
ADQNR/L**1506-A ACP4S ACS-5W BP-7 SP-2.5 ASD423 CSTB-3.5 T-15F

ATQ N R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 1 0 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

105°
b
f
f2

L2
L1
105°
h1

Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ATQNR/L123-A 0.750 0.750 4.500 1.125 0.750 1.000 0.700 0.031 TN**33... 2.2
ATQNR/L163-A 1.000 1.000 6.000 1.125 1.000 1.250 0.750 0.031 TN**33... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ATQNR/L2020K16-A 20 20 125 28 20 25 18 0.8 TN**1604... 3
ATQNR/L2525M16-A 25 25 150 28 25 32 20 0.8 TN**1604... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ATQNR/L**3-A, 16-A ACP3S ACS-5W BP-7 SP-2.5 AST322 CSTB-3.5 T-15F

Reference pages
ADQNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
ATQNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

B216 www.tungaloyamerica.com
AV QN R /L

Ext. Toolholder
Do u b l e -c l a m p to o l ho l d er w i t h 1 1 7 .5 ° ap p ro a c h a n gl e , f or n e ga t i v e 35° or 25° r h om b i c i n s e r t s

35

b
f
117.5°
L2

33.5
L1

25 +0.5
0
117.5°

h1
2020-type

h
Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

AVQNR/L123-A 0.750 0.750 4.500 1.380 0.750 1.000 0.031 V/YN**33... 2.2
AVQNR/L163-A 1.000 1.000 6.000 1.380 1.000 1.250 0.031 V/YN**33... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

AVQNR/L2020K16-A 20 20 125 35 20 25 0.8 V/YN**1604... 3
AVQNR/L2525M16-A 25 25 150 35 25 32 0.8 V/YN**1604... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
AVQNR/L... ACP3L ACS-5W BP-7 SP-2.5 ASV322 CSTB-3.5 T-15F

AR G N R /L
D o u b l e - c l a m p to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e ro u n d i n s e r t s

45° b
f
f2

45°
L2 L1
h1

Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

ARGNR/L164-A 1.000 1.000 6.000 1.125 1.000 1.250 0.750 0.250 RN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

ARGNR/L2525M12-A 25 25 150 28 25 32 20 6.35 RN**120400 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
ARGNR/L... ACP4S ACS-5W BP-7 SP-2.5 ASR420 CSTB-3.5 T-15F

Reference pages
AVQNR/L: Inserts → B093 -, B104, CBN → B167 -, PCD → B178
ARGNR/L: Inserts → B072

Tungaloy B217
Ext. Toolholder PC LN R /L-C HP
Le v e r l o c k t y p e to o l ho l d er w i t h 9 5 ° ap p roa c h a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s , w i t h c h a n n els fo r
h i g h p re s s u re co o l ant

L1
95°
L2

f2

b
f
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L1233-CHP 0.750 0.750 4.500 1.300 0.750 1.250 0.750 0.031 CN**33... 1.5
PCLNR/L124-CHP 0.750 0.750 4.500 1.300 0.750 1.250 0.750 0.031 CN**43... 2.2
PCLNR/L1633-CHP 1.000 1.000 6.000 1.300 1.000 1.250 0.750 0.031 CN**33... 1.5
PCLNR/L164-CHP 1.000 1.000 6.000 1.300 1.000 1.250 0.750 0.031 CN**43... 2.2

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR/L2020K0904-CHP 20 20 125 33 20 32 18 0.8 CN**0904... 2
PCLNR/L2020K12-CHP 20 20 125 33 20 32 18 0.8 CN**1204... 3
PCLNR/L2525M0904-CHP 25 25 150 33 25 32 18 0.8 CN**0904... 2
PCLNR/L2525M12-CHP 25 25 150 33 25 32 18 0.8 CN**1204... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PCLNR/L**0904-CHP,
LSC317 LCS3 P-2.5 LSP3 LCL33
PCLNR/L**33-CHP
PCLNR/L**12-CHP,
LSC42 LCS4 P-3 LSP4 LCL4
PCLNR/L**4-CHP

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PCLNR/L**0904-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PCLNR/L**33-CHP
PCLNR/L**12-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PCLNR/L**4-CHP

Reference pages

PCLNR/L-CHP: Inserts → B052 -, CBN → B165 -, PCD → B178

B218 www.tungaloyamerica.com
P D JN R /L-C H P

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er w i t h 9 3 ° ap p ro ach a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s , w i t h c h a n n e l s fo r
hig h p re s s u re c oo l ant

L1
L2

b
f
30°
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

PDJNR/L1233-CHP  0.750 0.750 4.500 1.420 0.750 1.250 0.031 DN**33... 1.5
PDJNR/L124-CHP  0.750 0.750 4.500 1.420 0.750 1.250 0.031 DN**43... 2.2
PDJNR/L1633-CHP 1.000 1.000 6.000 1.420 1.000 1.250 0.031 DN**33... 1.5
PDJNR/L164-CHP 1.000 1.000 6.000 1.420 1.000 1.250 0.031 DN**43... 2.2

Metric h b L1 L2 h1 f rε** Insert Torque*

PDJNR/L2020K1104-CHP 20 20 125 36 20 32 0.8 DN**1104... 2
PDJNR/L2020K15-CHP 20 20 125 36 20 32 0.8 DN**1504... 3
PDJNR/L2525M1104-CHP 25 25 150 36 25 32 0.8 DN**1104... 2
PDJNR/L2525M15-CHP 25 25 150 36 25 32 0.8 DN**1504... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PDJNR/L**1104-CHP,
ELSD32 LCS3 P-2.5 LSP3 LCL33L
PDJNR/L**33-CHP
PDJNR/L**15-CHP,
LSD43A LCS4 P-3 LSP4 LCL4
PDJNR/L**4-CHP

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PDJNR/L**1104-CHP,
CU-D-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PDJNR/L**33-CHP
PDJNR/L**15-CHP,
CU-D-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PDJNR/L**4-CHP

Reference pages

PDJNR/L-CHP: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B219
Ext. Toolholder P TG N R /L-C HP
Le v e r l o c k t y p e to o l ho l d er s w i t h 9 1 ° ap p roa c h a n gl e . For n e ga t i v e t r i a n gl e i n s e r t . H i gh - p re s s u re co o lant
c a p a b i l i t y.

L1
L2

f2

b
f
91°

h1

h
Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PTGNR/L1223-CHP 0.750 0.750 4.500 1.500 0.750 1.250 0.813 0.031 TN**23... 1.5
PTGNR/L123-CHP  0.750 0.750 4.500 1.500 0.750 1.250 0.813 0.031 TN**33... 1.5
PTGNR/L1623-CHP  1.000 1.000 6.000 1.500 1.000 1.250 0.813 0.031 TN**23... 1.5
PTGNR/L163-CHP  1.000 1.000 6.000 1.500 1.000 1.250 0.813 0.031 TN**33... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PTGNR/L2020K1104-CHP 20 20 125 38 20 32 21 0.8 TN**1104... 2
PTGNR/L2020K16-CHP 20 20 125 38 20 32 21 0.8 TN**1604... 2
PTGNR/L2525M1104-CHP 25 25 150 38 25 32 21 0.8 TN**1104... 2
PTGNR/L2525M16-CHP 25 25 150 38 25 32 21 0.8 TN**1604... 2

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PTGNR/L**1104-CHP,
- LCS23A P-2.5 LSP3 LCL23
PTGNR/L**23-CHP
PTGNR/L**16-CHP,
LST317 LCS3 P-2.5 LSP3 LCL3
PTGNR/L**3-CHP

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PTGNR/L**1104-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PTGNR/L**23-CHP
PTGNR/L**16-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PTGNR/L**3-CHP

Reference pages
PTGNR/L-CHP: Inserts → B082 -, CBN → B166 -, PCD → B178

B220 www.tungaloyamerica.com
P VJN R /L-C H P

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er s w i t h 9 3 ° ap p ro ac h a n gl e . For n e ga t i v e 35° or 25° r h om b i c i n s e r t .
High -p re s s u re c oo l ant cap ab i l i t y.
L1
L2
50°

b
f
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

PVJNR/L122.33-CHP 0.750 0.750 4.500 2.000 0.750 1.250 0.031 VN**2.33**E... 1.5
PVJNR/L162.33-CHP 1.000 1.000 6.000 2.000 1.000 1.250 0.031 VN**2.33**E... 1.5
PVJNR/L123-CHP  0.750 0.750 4.500 1.344 0.750 1.250 0.031 V/YN**33... 1.5
PVJNR/L163-CHP  1.000 1.000 6.000 1.344 1.000 1.250 0.031 V/YN**33... 1.5

Metric h b L1 L2 h1 f rε** Insert Torque*

PVJNR/L2020K1204-CHP 20 20 125 50 25 32 0.8 VN**1204... 2
PVJNR/L2525M1204-CHP 25 25 150 50 25 32 0.8 VN**1204... 2
PVJNR/L2020K16-CHP 20 20 125 50 20 32 0.8 V/YN**1604... 2
PVJNR/L2525M16-CHP 25 25 150 50 25 32 0.8 V/YN**1604... 2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PVJNR/L**1204-CHP
LSV212 LCS3V P-2.5 LSP3 LCL3V
PVJNR/L**2.33-CHP
PVJNR/L**16-CHP
LSV317 LCS3V P-2.5 LSP3 LCL3V
PVJNR/L**3-CHP

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PVJNR/L**1204-CHP
CU-V-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PVJNR/L**2.33-CHP
PVJNR/L**16-CHP
CU-V-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PVJNR/L**3-CHP

P V Q N R /L-C H P
Le v e r l o c k t y p e to o l ho l d er s w i t h 1 1 7 .5 ° ap p roa c h a n gl e . For n e ga t i v e 35° or 25° r h om b i c i n s e r t .
High -p re s s u re c o o l ant cap ab i l i t y.
L1
L2
117.5°
b
f

117.5°
h1

Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

PVQNR/L123-CHP 0.750 0.750 4.500 1.344 0.750 1.250 0.031 V/YN**33... 1.5
PVQNR/L163-CHP  1.000 1.000 6.000 1.344 1.000 1.250 0.031 V/YN**33... 1.5

Metric h b L1 L2 h1 f rε** Insert Torque*

PVQNR/L2020K16-CHP 20 20 125 42.5 20 32 0.8 V/YN**1604... 2
PVQNR/L2525M16-CHP 25 25 150 42.5 25 32 0.8 V/YN**1604... 2
*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PVQNR/L**-CHP LSV317 LCS3V P-2.5 LSP3 LCL3V

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PVQNR/L**-CHP CU-V-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2

Reference pages
PVJNR/L-CHP, PVQNR/L-CHP: Inserts → B093 -, B104, CBN → B167 -, PCD → B178
Tungaloy B221
 P W LN R /L-C HP
Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er s w i t h 9 5 ° ap p roa c h a n gl e . For n e ga t i v e 80° t r i gon i n s e r t . H i gh - p re s s u re co o lant
c a p a b i l i t y.

95° L1
L2

f2

b
f
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

PWLNR/L1233-CHP  0.750 0.750 4.500 1.969 0.750 1.250 0.781 0.031 WN**33... 1.5
PWLNR/L124-CHP  0.750 0.750 4.500 1.969 0.750 1.250 0.781 0.031 WN**43... 1.5
PWLNR/L1633-CHP 1.000 1.000 6.000 1.969 1.000 1.250 0.781 0.031 WN**33... 1.5
PWLNR/L164-CHP  1.000 1.000 6.000 1.969 1.000 1.250 0.781 0.031 WN**43... 1.5

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PWLNR/L2020K0604-CHP 20 20 125 34 20 32 20 0.8 WN**0604... 2
PWLNR/L2020K08-CHP 20 20 125 34 20 32 20 0.8 WN**0804... 3
PWLNR/L2525M0604-CHP 25 25 150 34 25 32 20 0.8 WN**0604... 2
PWLNR/L2525M08-CHP 25 25 150 34 25 32 20 0.8 WN**0804... 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
PWLNR/L**0604-CHP,
LSW312 LCS3 P-2.5 LSP3 LCL3
PWLNR/L**33-CHP
PWLNR/L**08-CHP,
LSW42 LCS4 P-2.5 LSP4 LCL4
PWLNR/L**4-CHP

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring Coolant screw Wrench 3
PWLNR/L**0604-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PWLNR/L**33-CHP
PWLNR/L**08-CHP,
CU-CW-CHP SRM3 T-8F OR6.4X0.9N SRM4X4TL360 P-2
PWLNR/L**4-CHP

Reference pages
PWLNR/L-CHP: Inserts → B097 -, CBN → B167

B222 www.tungaloyamerica.com
C- PC LN -C H P

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er w i t h Tung Cap co n n e c t i on , f or n e ga t i v e i n s e r t s , C 80º r h om b i c w i t h c h a n nels fo r
h ig h p re s s u re c o o l ant

95° Min. ød1

øSS
95°

f
Min. ød2
L1 L2 Right hand (R) shown.
Cutting edge style L
Inch øSS L1 L2 f ød1 ød2 rε** Insert
C4PCLNR/L27050-0904CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 CN**33...
C4PCLNR/L27050-12CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 CN**43...
C5PCLNR/L35060-12CHP 1.969 2.362 1.260 1.378 6.496 4.331 0.031 CN**43...
C6PCLNR/L45065-0904CHP 2.480 2.559 1.614 1.772 7.480 4.921 0.031 CN**33...
C6PCLNR/L45065-12CHP 2.480 2.559 1.614 1.772 7.480 4.921 0.031 CN**43...

Metric øSS L1 L2 f ød1 ød2 rε** Insert

C4PCLNR/L27050-0904-CHP 40 50 25 27 140 110 0.8 CN**0904...
C4PCLNR/L27050-12-CHP 40 50 25 27 140 110 0.8 CN**1204...
C5PCLNR/L35060-12-CHP 50 60 32 35 165 110 0.8 CN**1204...
C6PCLNR/L45065-0904-CHP 63 65 41 45 190 125 0.8 CN**0904...
C6PCLNR/L45065-12-CHP 63 65 41 45 190 125 0.8 CN**1204...
**rε: Standard corner radius

C- PD JN -C H P
Le v e r l o c k t y p e to o l ho l d er w i t h Tung Cap co n n e c t i on , f or n e ga t i v e i n s e r t s , D 55º r h om b i c w i t h c h a n nels fo r
h ig h p re s s u re c o o l ant

Min. ød1
øSS
30°

93°
f

L1 L2 Min. ød2
Cutting edge style J Right hand (R) shown.

Inch øSS L1 L2 f ød1 ød2 rε** Insert

C4PDJNR/L27050-1104CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 DN**33...
C4PDJNR/L27050-15CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 DN**43...
C5PDJNR/L35060-15CHP 1.969 2.362 1.260 1.378 6.496 4.331 0.031 DN**43...
C6PDJNR/L45065-1104CHP 2.480 2.559 1.614 1.772 7.480 4.331 0.031 DN**33...
C6PDJNR/L45065-15CHP 2.480 2.559 1.614 1.772 7.480 4.331 0.031 DN**43...

Metric øSS L1 L2 f ød1 ød2 rε** Insert

C4PDJNR/L27050-1104-CHP 40 50 25 27 140 110 0.8 DN**1104...
C4PDJNR/L27050-15-CHP 40 50 25 27 140 110 0.8 DN**1504(06)...
C5PDJNR/L35060-15-CHP 50 60 32 35 165 110 0.8 DN**1504(06)...
C6PDJNR/L45065-1104-CHP 63 65 41 45 190 110 0.8 DN**1104...
C6PDJNR/L45065-15-CHP 63 65 41 45 190 110 0.8 DN**1504(06)...
**rε: Standard corner radius

SPARE PARTS
FOR P-TYPE COOLANT SET
Designation Shim Clamping Wrench 1 Spring pin Lever Designation Coolant unit Mounting Wrench 2 O-ring
screw screw
C*PCLNR/L**-12-CHP LSC42 LCS4 P-3 LSP4 LCL4 C*PCLNR/L**-CHP CU-CW-CHP SRM3 T-8F OR6.4X0.9N
C*PDJNR/L**-15-CHP LSD43A LCS4 P-3 LSP4 LCL4 C*PDJLNR/L**-CHP CU-D-CHP SRM3 T-8F OR6.4X0.9N
C*PCLNR/L**0904-CHP LSC317 LCS3 P-2.5 LSP3 LCL33
C*PDJNR/L**1104-CHP ELSD32 LCS3 P-2.5 LSP3 LCL33L

Reference pages
C-PCLN-CHP: Inserts → B052 -, CBN → B165 -, PCD → B178
C-PDJN-CHP: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B223
Ext. Toolholder C -P W LN -C HP
Le v e r l o c k t y p e to o l ho l d er w i t h Tung Cap c on n e c t i on , f or n e ga t i v e i n s e r t s , W 80º t r i gon w i t h c h a n nels fo r
h i g h p re s s u re co o l ant

95° Min. ød1

øSS
95°

f
Cutting edge style L L1 L2 Min. ød2
Right hand (R) shown.

Inch øSS L1 L2 f ød1 ød2 rε** Insert

C4PWLNR/L27050-0604CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 WN**33...
C4PWLNR/L27050-08CHP 1.575 1.969 0.984 1.063 5.512 4.331 0.031 WN**43...
C6PWLNR/L45065-08CHP 2.480 2.559 1.614 1.772 7.480 4.331 0.031 WN**43...

Metric øSS L1 L2 f ød1 ød2 rε** Insert

C4PWLNR/L27050-0604-CHP 40 50 25 27 140 110 0.8 WN**0604...
C4PWLNR/L27050-08-CHP 40 50 25 27 140 110 0.8 WN**0804...
C6PWLNR/L45065-08-CHP 63 65 41 45 190 110 0.8 WN**0804...
**rε: Standard corner radius
SPARE PARTS
FOR P-TYPE COOLANT SET
Designation Shim Clamping Wrench 1 Spring pin Lever Designation Coolant unit Mounting Wrench 2 O-ring
screw screw
C*PWLNR/L**-08-CHP LSW42BL LCS4 P-3 LSP4 LCL4 C*PWLNR/L**-CHP CU-CW-CHP SRM3 T-8F OR6.4X0.9N
C*PWLNR/L**0604-CHP LSW312 LCS3 P-2.5 LSP3 LCL3

C -P VJN R /L- CHP

Le v e r l o c k to ol ho l d er s w i t h Tung Cap co nn e c t i on – 93° a p p roa c h a n gl e . For n e ga t i v e 35° or 25° r ho mbic
i n s e r t . H i g h - p re s s u re c o o l a n t c a p a b i l i t y.

Min. ød1
øD

≤50°
f

93°

L1 L2 Min. ød2
Cutting edge style J Right hand (R) shown.

Inch øD L1 L2 f ød1 ød2 rε** Insert

C4PVJNR/L27060-1204-CHP 1.575 2.362 0.787 1.063 5.512 3.543 0.031 VN**2.33**E...
C4PVJNR/L27060-16-CHP 1.575 2.362 - 1.063 5.512 4.331 0.031 V/YN**33...
C6PVJNR/L45065-1204-CHP 2.480 2.559 1.240 1.772 7.480 3.189 0.031 VN**2.33**E...
C6PVJNR/L45065-16-CHP 2.480 2.559 - 1.772 7.480 3.189 0.031 V/YN**33...

Metric øD L1 L2 f ød1 ød2 rε** Insert

C4PVJNR/L27060-1204-CHP 40 60 20 27 140 90 0.8 VN**1204...
C4PVJNR/L27060-16-CHP 40 60 - 27 140 110 0.8 V/YN**1604...
C6PVJNR/L45065-1204-CHP 63 65 31.5 45 190 81 0.8 VN**1204...
C6PVJNR/L45065-16-CHP 63 65 - 45 190 81 0.8 V/YN**1604...
Applicable for 14 MPa pressure coolant. **rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Wrench 1 Spring pin Lever
C*PVJNR/L**-1204-CHP LSV212 LCS3V P-2.5 P-3 LSP3 LCL3V
C*PVJNR/L**-16-CHP LSV317 LCS3V P-2.5 - LSP3 LCL3V

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring
C*PVJNR/L**-CHP CU-V-CHP SRM3 T-8F OR6.4X0.9N

Reference pages
C-PWLN-CHP: Inserts → B097 -, CBN → B167
C-PVJNR/L-CHP: Inserts → B093 -, B104, CBN → B167 -, PCD → B178

B224 www.tungaloyamerica.com
C-P C M N N -C H P

Ext. Toolholder
Le v e r l o c k to o l h o l d er w i t h Tung Cap co nnect i on . For n e ga t i v e 80° r h om b i c i n s e r t . H i gh - p re s s u re c oo lant
c a p a b i l i t y.

95°

øD
95°
50°
L1
Cutting edge style M
Metric h b L1 L2 Insert
C6PCMNN00130-12-CHP 63 115 0 0.8 CN**1204...
Applicable for 14 MPa pressure coolant For external turning only.
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
C6PCMNN00130-12-CHP LSC42 LCS4 P-3 LSP4 LCL4

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring
C6PCMNN00130-12-CHP CU-CW-CHP SRM3 T-8F OR6.4X0.9N

Reference pages
C-PCMNN-CHP: Inserts → B052 -, CBN → B165 -, PCD → B178

Tungaloy B225
Ext. Toolholder C -PD M N L-C HP
Le v e r l o c k to o l ho l d er w i t h Tung Cap co nne c t i on . For n e ga t i v e 55° r h om b i c i n s e r t . H i gh - p re s s u re co o lant
c a p a b i l i t y.

77°

f
øD
47°

48°
L1
Cutting edge style M Left hand (L) shown.

Metric øD L1 f rε** Insert

C6PDMNL00130-1104-CHP 63 130 0 0.8 DN**1104...
Applicable for 14 MPa pressure coolant For external turning only.
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench 1 Spring pin Lever
C6PDMNL00130-1104-CHP ELSD32 LCS3 P-2.5 LSP3 LCL33L

SPARE PARTS
Designation Coolant unit Mounting screw Wrench 2 O-ring
C6PDMNL00130-1104-CHP CU-D-CHP SRM3 T-8F OR6.4X0.9N

Reference pages
C-PDMNL-CHP: Inserts → B063 -, CBN → B165 -, PCD → B178

B226 www.tungaloyamerica.com
J S D J2X R /L-C H P

Ext. Toolholder
Scre w -o n to o l h ol d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e , f or DXG U i n s e r t s , w i t h c h a n n e l s f or h i gh
pre s s u re c o o l a n t

L1 Without offset
L2

f2
f

b
30°
93°

h1

h
Cutting edge style J2 5/16”-24UNF
Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2XR/L082-CHP 0.500 0.500 3.344 0.750 0.500 0.500 0.730 0.008 DXGU22**L/R... 0.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2XR/L1212F07-CHP 12 12 85 19 12 0 18.5 0.2 DXGU0703**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSDJ2XR/L**-CHP SR34-514 S-CU-CHP T-7F

J SW L2XR /L-C HP
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 5 ° a p p roa c h a n gl e , f or W XG U i n s e r t s , w i t h c h a n n e l s f or h i g h
pres s u re c o o l a n t

L1 Without offset
95°
L2
f2
f

b
95°
h1

Cutting edge style L2 5/16”-24UNF

Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSWL2XR/L082-CHP 0.500 0.500 3.344 0.750 0.500 0.500 0.650 0.008 WXGU22**L/R... 0.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSWL2XR/L1212F04-CHP 12 12 85 18 12 0 16.5 0.2 WXGU0403**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSWL2XR/L**-CHP SR34-514 S-CU-CHP T-7F

Reference pages
JSDJ2XR/L-CHP: Inserts → B122 -
JSWL2XR/L-CHP: Inserts → B154

Tungaloy B227
Ext. Toolholder JS VJ2X R /L- CHP
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 93° a p p roa c h a n gl e , f or V XG U i n s e r t s , w i t h c ool a n t n oz l e fo r hig h
p re s s u re

L1 Without offset
L2

f2
f

b
50°
93°

h1

h
Cutting edge style J2 5/16”-24UNF
Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2XR/L087-CHP 0.500 0.500 3.344 0.689 0.500 0.500 0.531 0.008 VXGU73.5**L/R... 0.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2XR/L1212F09-CHP 12 12 85 20 12 0 13.5 0.2 VXGU09T2**L/R... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping **rε: Standard corner radius
Note: Right-hand toolholders (R) are used with left-hand inserts (L). Left-hand toolholders (L) are used with right-hand inserts (R).

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSVJ2XR/L**-CHP SR34-508 S-CU-CHP T-7F

JS D J2C R /L-CHP
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 93° a p p roa c h a n gl e , f or p os i t i v e 55° r h om b i c i n s e r t s , w i th chan-
n e l s f o r h i g h p ressure co o l ant

L1 Without offset
L2
30°
f2
f

b
93°
h1

Cutting edge style J2 5/16”-24UNF

Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L082-CHP 0.500 0.500 3.344 0.710 0.500 0.500 0.710 0.008 DC**21.5... 0.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L1212F07-CHP 12 12 85 18 12 0 18 0.2 DC**0702... 0.9
JSDJ2CR/L1212F11-CHP 12 12 85 19 12 0 20.5 0.2 DC**11T3... 0.9

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSDJ2CR/L082-CHP
CSTB-2.5 S-CU-CHP T-8F
JSDJ2CR/L1212F07-CHP
JSDJ2CR/L1212F11-CHP CSTB-4SD S-CU-CHP T-8F

Reference pages
JSVJ2XR/L-CHP: Inserts → B152
JSDJ2CR/L-CHP: Inserts → B116 -, CBN → B170 -, PCD → B179

B228 www.tungaloyamerica.com
J SV J2B R /L-C HP

Ext. Toolholder
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e , f or p os i t i v e 35° r h om b i c i n s e r t s , w i t h c han-
ne l s f o r h i g h p ressure co o l ant

L1 Without offset
L2

f2
f

b
50°
93°

h1

h
5/16”-24UNF
Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2BR/L082-CHP 0.500 0.500 3.344 0.930 0.500 0.500 0.610 0.008 VB**22... 0.9

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2BR/L1212F11-CHP 12 12 85 23.6 12 0 14.7 0.2 VB**1103... 1.2

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSVJ2BR/L**-CHP CSTB-2.5 S-CU-CHP T-8F

Reference pages
JSVJ2BR/L-CHP: Inserts → B147 -, CBN → B171 -

Tungaloy B229
 PARTS FOR COOLANT HOSE
Ext. Toolholder

Connecting hose
Fig. 1 Fig. 2

Th Th1 Th1
L Th
L

Max. pressure
Metric L Th Th1 Fig.
(Mpa)
CHP-HOSE-G1/8-7/16-200BS 200 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-G1/8-7/16-250BS 250 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-5/16-7/16-200BS 200 5/16”-24UNF 7/16"-20 UNF 20 1
CHP-HOSE-5/16-G1/8-200BS 200 5/16”-24UNF G1/8"-28 BSPP 20 1
CHP-HOSE-G1/8-G1/8-200BB 200 G1/8"-28 BSPP G1/8"-28 BSPP 26 2
CHP-HOSE-G1/8-G1/8-250BB 250 G1/8"-28 BSPP G1/8"-28 BSPP 26 2

Connector Seal washer

HEX9/16”
7/16”-20 UNF 1/8”-28 BSPP
4.0

ød
øD
13.8

37°
14 7.1 W
28.75

Metric Metric øD ød W
CHP-NIPPLE-G1/8-7/16UNF CHP-COPPER-SEAL1/8 15 10 1
CHP-COPPER-SEAL5/16 11 8 1
CHP-COPPER-SEAL5/16-2.5 11 8 2.5

Connector for small lathe

with seal washer

9 SW = 12
G1/8”-28 BSPP

6
11
4

25 ø13
5/16”-24 UNF

Metric
CHP-CONECTOR/5/16-G1/8

B230 www.tungaloyamerica.com
SYJB R /L

Ext. Toolholder
S c re w -o n c l a m p to o l ho l d er w i t h 9 3 ° ap p ro ac h a n gl e , f or p os i t i v e 25° r h om b i c i n s e r t s

b
f
60˚
93° L2
L1

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SYJBR/L123 0.750 0.750 4.500 1.350 0.750 1.000 0.031 YWMT16T3...
SYJBR/L163 1.000 1.000 6.000 1.500 1.000 1.250 0.031 YWMT16T3...

Metric h b L1 L2 h1 f rε** Insert

SYJBR/L2020K16 20 20 125 35 20 25 0.8 YWMT16T3...
SYJBR/L2525M16 25 25 150 40 25 32 0.8 YWMT16T3...
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
SYJBR/L... CSTB-2.5L080 T-8F

SYQ B R /L
S c re w -o n c l a m p to o l ho l d er w i t h 1 2 2 .5 ° ap p roa c h a n gl e , f or p os i t i v e 25° r h om b i c i n s e r t s

b
f

30˚
L2 L1
122.5°
h1

Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SYQBR/L123 0.750 0.750 4.500 1.350 0.750 1.000 0.031 YWMT16T3...
SYQBR/L163 1.000 1.000 6.000 1.500 1.000 1.250 0.031 YWMT16T3...

Metric h b L1 L2 h1 f rε** Insert

SYQBR/L2020K16 20 20 125 35 20 27 0.8 YWMT16T3...
SYQBR/L2525M16 25 25 150 35 25 32 0.8 YWMT16T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
SYQBR/L... CSTB-2.5L080 T-8F

Reference pages
SYJBR/L, SYQBR/L: Inserts → B155

Tungaloy B231
Ext. Toolholder SY H B R /L
Sc re w -o n c l a mp to o l ho l d er w i t h 1 0 0 ° ap p roa c h a n gl e , f or p os i t i v e 25° r h om b i c i n s e r t s

b
f
53°
L2
100° L1

h1

h
Cutting edge style H Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SYHBR/L123 0.750 0.750 4.500 1.350 0.750 1.000 0.031 YWMT16T3...
SYHBR/L163 1.000 1.000 6.000 1.500 1.000 1.250 0.031 YWMT16T3...

Metric h b L1 L2 h1 f rε** Insert

SYHBR/L2020K16 20 20 125 35 20 27 0.8 YWMT16T3...
SYHBR/L2525M16 25 25 150 40 25 32 0.8 YWMT16T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
SYHBR/L... CSTB-2.5L080 T-8F

SY I B N
Sc re w -o n c l a mp to o l ho l d er w i t h 7 7 .5 ° ap proa c h a n gl e , f or p os i t i v e 25° r h om b i c i n s e r t s

30°
f

L2
L1 b
77.5°
h1

Cutting edge style I

Inch h b L1 L2 h1 f rε** Insert
SYIBN123 0.750 0.750 4.500 1.250 0.750 0.375 0.031 YWMT16T3...
SYIBN163 1.000 1.000 6.000 1.500 1.000 0.500 0.031 YWMT16T3...

Metric h b L1 L2 h1 f rε** Insert

SYIBN2020K16 20 20 125 32 20 10 0.8 YWMT16T3...
SYIBN2525M16 25 25 150 40 25 12.5 0.8 YWMT16T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
SYIBN... CSTB-2.5L080 T-8F

Reference pages
SYHBR/L, SYIBN: Inserts → B155

B232 www.tungaloyamerica.com
DC LN R /L

Ext. Toolholder
" O n e -Do u b l e " to o l ho l d er w i t h 9 5 ° ap p ro ach a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s

45°
95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DCLNR/L2020K12 20 20 125 30 20 25 18 0.8 CN**1204...
DCLNR/L2525M12 25 25 150 30 25 32 18 0.8 CN**1204...
DCLNR/L3225P12 32 25 170 30 32 32 18 0.8 CN**1204...

Note: Except for 57-type chipbreaker inserts

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DCLNR/L... DCPM-43 DLCL43 DPIS43 DLCS43 LSC42 BP-10 LSP4 P-3 P-4

DW LN R /L
" O n e - D o u b l e " to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i g o n i n s e r t s

95°
95°

bb
ff

L22 L11
95°
95°
hh11

hh

Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

DWLNR/L2020K06 20 20 125 25.5 20 25 0.8 WN**0604...
DWLNR/L2020K08 20 20 125 31 20 25 0.8 WN**0804...
DWLNR/L2525M06 25 25 150 26 25 32 0.8 WN**0604...
DWLNR/L2525M08 25 25 150 31 25 32 0.8 WN**0804...
DWLNR/L3225P08 32 25 170 30 32 32 0.8 WN**0804...

Note: Except for 57-type chipbreaker inserts

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DWLNR/L**06 DCPM-33 LCL33 DPIS33 DLCS33 LSW312 BP-9 LSP3 P-2.5 P-3
DWLNR/L**08 DCPM-43 DLCL43 DPIS43 DLCS43 LSW42 BP-10 LSP4 P-3 P-4

Reference pages
DCLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178
DWLNR/L: Inserts → B097 -, CBN → B167

Tungaloy B233
Ext. Toolholder D D JN R /L
"O n e -Do u b l e " to o l ho l d er w i t h 9 3 ° ap p ro ac h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
f2
f
30°
L2
L1
93°

h1

h
Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DDJNR/L2020K15 20 20 125 38 20 25 19 0.8 DN**1504...
DDJNR/L2020K1506 20 20 125 38 20 25 19 0.8 DN**1506...
DDJNR/L2525M15 25 25 150 38 25 32 19 0.8 DN**1504...
DDJNR/L2525M1506 25 25 150 38 25 32 19 0.8 DN**1506...
DDJNR/L3225P15 32 25 170 38 32 32 19 0.8 DN**1504...
DDJNR/L3225P1506 32 25 170 38 32 32 19 0.8 DN**1506...

Note: Except for 57-type chipbreaker inserts

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DDJNR/L**15 DCPM-43 DLCL43 DPIS43 DLCS43 LSD42 BP-10 LSP4 P-3 P-4
DDJNR/L**1506 DCPM-43 DLCL43 DPIS44 DLCS43 LSD42 BP-10 LSP4 P-3 P-4

DTG N R /L
" O n e - D o u b l e " to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
f2

L2
L1
91°
h1

Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DTGNR/L2020K16 20 20 125 21 20 25 16 0.8 TN**1604...
DTGNR/L2525M16 25 25 150 21 25 32 21 0.8 TN**1604...
DTGNR/L2525M22 25 25 150 28 25 32 25 0.8 TN**2204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DTGNR/L**16 DCPM-33 LCL33 DPIS33 DLCS33 LST317 BP-9 LSP3 P-2.5 P-3
DTGNR/L**22 DCPM-43 DLCL43 DPIS43 DLCS43 LST42 BP-10 LSP4 P-3 P-4

Reference pages
DDJNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
DTGNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

B234 www.tungaloyamerica.com
DS B N R /L

Ext. Toolholder
" O n e - D o u b l e " to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
f
L2
75° L1

h1

h
Cutting edge style B Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

DSBNR/L2020K12 20 20 125 35 20 17 0.8 SN**1204...
DSBNR/L2525M12 25 25 150 35 25 22 0.8 SN**1204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DSBNR/L... DCPM-43 DLCL43 DPIS43 DLCS43 LSS42 BP-10 LSP4 P-3 P-4

DS D N N
" O n e - D o u b l e " to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
f
45° L2 L1
h1

h
Cutting edge style D
Metric h b L1 L2 h1 f rε** Insert
DSDNN2020K12 20 20 125 36 20 10 0.8 SN**1204...
DSDNN2525M12 25 25 150 36 25 12.5 0.8 SN**1204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DSDNN... DCPM-43 DLCL43 DPIS43 DLCS43 LSS42 BP-10 LSP4 P-3 P-4

DSSN R /L
" O n e -Do u b l e " to o l ho l d er w i t h 4 5 ° ap p ro ach a n gl e (S - s t y l e ), f or n e ga t i v e s q u a re i n s e r t s

45°
b
f
f2

45° L2
L1
h1

Cutting edge style S Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DSSNR/L2020K12 20 20 125 34.3 20 25 8.3 0.8 SN**1204...
DSSNR/L2525M12 25 25 150 34.3 25 32 8.3 0.8 SN**1204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DSSNR/L... DCPM-43 DLCL43 DPIS43 DLCS43 LSS42 BP-10 LSP4 P-3 P-4

Reference pages
DSBNR/L, DSDNN, DSSNR/L: Inserts → B073 -, CBN → B166, PCD → B178

Tungaloy B235
Ext. Toolholder D SK N R /L
" O n e - D o u b l e " to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

45˚
75°

b
f
f2
L1
L2

h1

h
Cutting edge style K Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DSKNR/L2020K12 20 20 125 31 20 25 17 0.8 SN**1204...
DSKNR/L2525M12 25 25 150 31 25 32 17 0.8 SN**1204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DSKNR/L... DCPM-43 DLCL43 DPIS43 DLCS43 LSS42 BP-10 LSP4 P-3 P-4

DTFN R /L
"O n e -Do u b l e " to o l ho l d er f o r f aci ng w i t h 91° a p p roa c h a n gl e , n e ga t i v e t r i a n gl e i n s e r t s

91° 30°

b
f2
f

L2 L1
h1

h
Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DTFNR/L2020K16 20 20 125 23 20 25 18.5 0.8 TN**1604...
DTFNR/L2525M16 25 25 150 23 25 32 20 0.8 TN**1604...
DTFNR/L2525M22 25 25 150 31 25 32 24 0.8 TN**2204...
Note: Except for 57-type chipbreaker inserts
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DTFNR/L**16 DCPM-33 LCL33 DPIS33 DLCS33 LST317 BP-9 LSP3 P-2.5 P-3
DTFNR/L**22 DCPM-43 DLCL43 DPIS43 DLCS43 LST42 BP-10 LSP4 P-3 P-4

Reference pages
DSKNR/L: Inserts → B073 -, CBN → B166, PCD → B178
DTFNR/L: Inserts → B082 -, CBN → B166, PCD → B178

B236 www.tungaloyamerica.com
DD Q N R /L

Ext. Toolholder
" On e -Do u b l e " to o l ho l d er w i t h 1 0 7 .5 ° ap p ro a c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
107.5°

f
L2
L1
107.5°

h1

h
Cutting edge style Q Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

DDQNR/L2020K15 20 20 125 35 20 25 0.8 DN**1504...
DDQNR/L2020K1506 20 20 125 35 20 25 0.8 DN**1506...
DDQNR/L2525M15 25 25 150 35 25 32 0.8 DN**1504...
DDQNR/L2525M1506 25 25 150 35 25 32 0.8 DN**1506...
DDQNR/L3225P15 32 25 170 35 32 32 0.8 DN**1504...
DDQNR/L3225P1506 32 25 170 35 32 32 0.8 DN**1506...

Note: Except for 57-type chipbreaker inserts

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DDQNR/L**15 DCPM-43 DLCL43 DPIS43 DLCS43 LSD42 BP-10 LSP4 P-3 P-4
DDQNR/L**1506 DCPM-43 DLCL43 DPIS44 DLCS43 LSD42 BP-10 LSP4 P-3 P-4

DR G N R /L
" O n e - D o u b l e " to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e ro u n d i n s e r t s

45°

b
f
f2

L2 L1
45°
h1

Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

DRGNR/L2525M12 25 25 150 28 25 32 18 6.35 RN**120400

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Lever Piston Clamp screw Shim Spring Spring pin Wrench 1 Wrench 2
DRGNR/L... DCPM-43 DLCL43 DPIS43 DLCS43 LSR42 BP-10 LSP4 P-3 P-4

Reference pages
DDQNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
DRGNR/L: Inserts → B072

Tungaloy B237
Ext. Toolholder P C LN R /L
Le v e r l o c k t y pe to o l ho l d er w i t h 9 5 ° ap p roa c h a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert

PCLNR/L1233 0.750 0.750 4.500 0.813 0.750 1.000 0.625 0.031 CN*33...
PCLNR/L1633 1.000 1.000 6.000 0.813 1.000 1.250 1.250 0.031 CN*33...

Metric h b L1 L2 h1 f f2 rε** Insert

PCLNR/L1616H09 16 16 100 20 16 20 15 0.8 CN**0903...
PCLNR/L2020K09 20 20 125 20 20 25 15 0.8 CN**0903...
PCLNR/L2525M09 25 25 150 20 25 32 15 0.8 CN**0903...
PCLNR/L1616 16 16 100 26 16 20 - 0.8 CN**1204...
PCLNR/L2020 20 20 125 28 20 25 18 0.8 CN**1204...
PCLNR/L2525M4 25 25 150 28 25 32 18 0.8 CN**1204...
PCLNR/L3225P4 32 25 170 28 32 32 18 0.8 CN**1204...
PCLNR/L3232 32 32 170 40 32 40 25 1.2 CN**1906...
PCLNR/L1616H12E 16 16 100 26 16 20 - 0.8 CN**1204...
PCLNR/L2020K12E 20 20 125 28 20 25 18 0.8 CN**1204...
PCLNR/L2525M12E 25 25 150 28 25 32 18 0.8 CN**1204...
PCLNR/L3225P12E 32 25 170 28 32 32 18 0.8 CN**1204...
PCLNR/L2525M16E 25 25 150 31 25 25 - 1.2 CN**1606...
PCLNR/L3225P16E 32 25 150 31 32 32 - 1.2 CN**1606...
PCLNR3232P16E 32 32 170 31 32 40 - 1.2 CN**1606...
PCLNR/L3232P19E 32 32 170 40 32 40 25 1.2 CN**1906...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PCLNR/L1233, 1633 LSC317 LCS3 P-2.5 LSP3 LCL33
PCLNR/L1616H09 ELSC32 LCS3 P-2.5 LSP3L LCL33
PCLNR/L2020K09 ELSC32 LCS3 P-2.5 LSP3L LCL33
PCLNR/L2525M09 ELSC32 LCS3 P-2.5 LSP3L LCL33
PCLNR/L1616 LSC42 LCS4CA P-3 LSP4 LCL4
PCLNR/L2020 LSC42 LCS4 P-3 LSP4 LCL4
PCLNR/L2525M4 LSC42 LCS4 P-3 LSP4 LCL4
PCLNR/L3225P4 LSC42 LCS4 P-3 LSP4 LCL4
PCLNR/L3232 LSC63 LCS6 P-4 LSP6 LCL6
PCLNR/L1616H12E ELSC42 LCS4CA P-3 LSP4 LCL4
PCLNR/L2020K12E ELSC42 LCS4 P-3 LSP4S LCL43M
PCLNR/L2525M12E ELSC42 LCS4 P-3 LSP4S LCL43M
PCLNR/L3225P12E ELSC42 LCS4 P-3 LSP4S LCL43M
PCLNR/L2525M16E ELSC53 LCS5 P-3 LSP6C LCL5
PCLNR/L3225P16E ELSC53 LCS5 P-3 LSP6C LCL5
PCLNR/L3232P16E ELSC53 LCS5 P-3 LSP6C LCL5
PCLNR/L3232P19E ELSC63 LCS6 P-4 LSP6 LCL6

Reference pages
PCLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178 -

B238 www.tungaloyamerica.com
PTL2N R /L

Ext. Toolholder
No -o f f s e t Le v e r- l o ck cl am p to o l ho l d er w i t h 95° a p p roa c h a p p roa c h a n gl e , f or n e ga t i v e 60° t r i a n gu l a r
inserts

45°

b
f
L2
L1
95°

h1

h
Cutting edge style L2 Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

PTL2NR/L2020H16 20 20 100 22 20 20 0.4 TN**1604... 2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PTL2NR/L... LST317 D30 LCS3 P-2.5 LSP3 LCL3

P D JN R /L
Le v e r l o c k t y p e to o l ho l d er w i t h 9 3 ° ap p ro ach a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
f
f2
30° L2
L1
93°
h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert

PDJNR/L1033 0.625 0.625 4.500 1.250 0.625 0.750 0.625 0.031 DN**33...
PDJNR/L1233 0.750 0.750 4.500 1.250 0.750 1.000 0.625 0.031 DN**33...
PDJNR/L1633 1.000 1.000 6.000 1.250 1.000 1.250 0.750 0.031 DN**33...

Metric h b L1 L2 h1 f f2 rε** Insert

PDJNR/L1616H11 16 16 100 27 16 20 16 0.8 DN**1104...
PDJNR/L2020K11 20 20 125 27 20 25 16 0.8 DN**1104...
PDJNR/L2020 20 20 125 34 20 25 19 0.8 DN**1504...
PDJNR2020K15E 20 20 125 36 20 25 - 0.8 DN**1506...
PDJNR/L2520 25 20 150 34 25 25 19 0.8 DN**1504...
PDJNR/L2525M11 25 25 150 27 25 32 19 0.8 DN**1104...
PDJNR/L2525 25 25 150 34 25 32 19 0.8 DN**1504...
PDJNR/L2525M15E 25 25 150 36 25 32 - 0.8 DN**1506...
PDJNR/L3225 32 25 170 32 32 32 19 0.8 DN**1504...
PDJNR3225P15E 32 25 170 36 32 34 - 0.8 DN**1506...
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PDJNR/L21033, 1023, 1633 ELSD32 LCS3 P-2.5 LSP3 LCL33
PDJNR/L1616H11, 2020K11 ELSD32 LCS3 P-2.5 LSP3 LCL33L
PDJNR/L2020 LSD42 LCS4 P-3 LSP4 LCL4
PDJNR2020K15E ELSD42 ELCS4 P-3 LSP4S LCL44
PDJNR/L2520 LSD42 LCS4 P-3 LSP4 LCL4
PDJNR/L2525 LSD42 LCS4 P-3 LSP4 LCL4
PDJNR/L2525M15E ELSD42 ELCS4 P-3 LSP4S LCL44
PDJNR/L3225 LSD42 LCS4 P-3 LSP4 LCL4
PDJNR3225P15E ELSD42 ELCS4 P-3 LSP4S LCL44

Reference pages
PTL2NR/L: Inserts → B082 -, CBN → B166, PCD → B178
PDJNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B239
Ext. Toolholder P D PN N
Le v e r l o c k t y pe to o l ho l d er w i t h 6 2 .5 ° ap p roa c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
L2
L1

10°
62.5°

h1

h
Cutting edge style P 10°

Metric h b L1 L2 h1 f rε** Insert

PDPNN2525 25 25 150 36 25 12.5 0.8 DN**1504...
PDPNN2525M15E 25 25 150 36 25 12.5 0.8 DN**1506...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PDPNN2525 LSD42 LCS4 P-3 LSP4 LCL4
PDPNN2525M15E ELSD42 ELCS4 P-3 LSP4S LCL44

P TG N R /L
Le v e r l o c k t y p e to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
f2

L2
91° L1
h1

h
Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert

PTGNR/L1223 0.750 0.750 4.500 0.750 0.750 1.000 0.625 0.031 TN**23...
PTGNR/L1623 1.000 1.000 6.000 0.750 1.000 1.250 0.875 0.031 TN**23...

Metric h b L1 L2 h1 f f2 rε** Insert

PTGNR/L1616 16 16 100 22 16 20 16 0.8 TN**1604...
PTGNR/L2020 20 20 125 22 20 25 16 0.8 TN**1604...
PTGNR/L2525M3 25 25 150 22 25 32 21 0.8 TN**1604...
PTGNR/L2525M4 25 25 150 28 25 32 24 0.8 TN**2204...
PTGNR3225P4 32 25 170 28 32 32 24 0.8 TN**2204...
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PTGNR/L1223, 1623 - LCS23A P-2.5 - LCL3
PTGNR/L1616, 2020 LST317 LCS3 P-2.5 LSP3 LCL3
PTGNR/L2525M3 LST317 LCS3 P-2.5 LSP3 LCL3
PTGNR/L2525M4 LST42 LCS4 P-3 LSP4 LCL4
PTGNR3225P4 LST42 LCS4 P-3 LSP4 LCL4

Reference pages
PDPNN: Inserts → B063 -, CBN → B165 -, PCD → B178
PTGNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

B240 www.tungaloyamerica.com
P C B N R /L

Ext. Toolholder
Le v e r l o c k t y p e to o l ho l d er w i t h 7 5 ° ap p ro ach a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s

b
100° L2
75°
L1

h1

h
Cutting edge style B Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

PCBNR/L2525 25 25 150 28 25 22 0.8 CN**1204...

Note: 100 corners are used

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PCBNR/L2525 LSC42 LCS4 P-3 LSP4 LCL4

P SB N R /L
Le v e r l o c k t y p e to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
f

L2
75° L1
h1

h
Cutting edge style B Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

PSBNR/L1616 16 16 100 22 16 13 0.8 SN**0903...
PSBNR/L2020 20 20 125 28 20 17 0.8 SN**1204...
PSBNR/L2525 25 25 150 24 25 22 0.8 SN**1204...
PSBNR/L3232 32 32 170 40 32 27 1.2 SN**1906...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PSBNR/L1616 LSS33 LCS3 P-2.5 LSP3L LCL3
PSBNR/L2*2* LSS42 LCS4 P-3 LSP4 LCL4
PSBNR/L3232 LSS63 LCS6 P-4 LSP6 LCL6

Reference pages
PCBNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178
PSBNR/L: Inserts → B073 -, CBN → B166, PCD → B178

Tungaloy B241
Ext. Toolholder PSDNN
Le v e r l o c k t y p e to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
f
45° L2
L1

h1

h
Cutting edge style D
Metric h b L1 L2 h1 f rε** Insert
PSDNN1616 16 16 100 22 16 8 0.8 SN**0903...
PSDNN2020 20 20 125 30 20 10.3 0.8 SN**1204...
PSDNN2525 25 25 150 30 25 12.8 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PSDNN1616 LSS33 LCS3 P-2.5 LSP3L LCL3
PSDNN2020 LSS42 LCS4 P-3 LSP4 LCL4
PSDNN2525 LSS42 LCS4 P-3 LSP4 LCL4

P S S N R /L
Le v e r l o c k t y pe to o l ho l d er w i t h 4 5 ° ap p roa c h a n gl e (S - s t y l e ), f or n e ga t i v e s q u a re i n s e r t s

45°

b
f
f2

45° L2 L1
h1

h
Cutting edge style S Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

PSSNR/L1616 16 16 94 16 16 20 6.1 0.8 SN**0903...
PSSNR/L2020 20 20 116 21 20 25 8.3 0.8 SN**1204...
PSSNR/L2525 25 25 141 21 25 32 8.3 0.8 SN**1204...
PSSNR3225 32 25 161 21 32 32 8.3 0.8 SN**1204...
PSSNR/L3232 32 32 157.5 27.5 32 40 12.5 1.2 SN**1906...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PSSNR/L1616 LSS33 LCS3 P-2.5 LSP3L LCL3
PSSNR/L2020 LSS42 LCS4 P-3 LSP4 LCL4
PSSNR/L**25 LSS42 LCS4 P-3 LSP4 LCL4
PSSNR/L3232 LSS63 LCS6 P-4 LSP6 LCL6

Reference pages
PSDNN, PSSNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178 -

B242 www.tungaloyamerica.com
P SK N R /L

Ext. Toolholder
Le v e r l o c k t y p e to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

45˚
75°

b
f
f2
L2 L1

h1

h
Cutting edge style K Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

PSKNR/L1616 16 16 100 17 16 25 15 0.8 SN**0903...
PSKNR/L2020 20 20 125 22 20 25 17 0.8 SN**1204...
PSKNR/L2525 25 25 150 22 25 32 17 0.8 SN**1204...
PSKNR3232 32 32 170 40 32 40 27 1.2 SN**1906...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PSKNR/L1616 LSS33 LCS3 P-2.5 LSP3L LCL3
PSKNR/L2*2* LSS42 LCS4 P-3 LSP4 LCL4
PSKNR3232 LSS63 LCS6 P-4 LSP6 LCL6

P TFN R /L
Le v e r l o c k t y p e to o l ho l d er f o r f aci ng w i t h 9 1° a p p roa c h a n gl e , n e ga t i v e t r i a n gl e i n s e r t s
30°

91°

b
f2
f

L2
L1
h1

h
Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

PTFNR/L1616 16 16 100 22 16 20 16 0.8 TN**1604...
PTFNR/L2020 20 20 125 22 20 25 16 0.8 TN**1604...
PTFNR/L2525M3 25 25 150 22 25 32 20 0.8 TN**1604...
PTFNR/L2525M4 25 25 150 28 25 32 24 0.8 TN**2204...
PTFNR/L3225P4 32 25 170 28 32 32 24 0.8 TN**2204...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PTFNR/L1616, 2020 LST317 LCS3 P-2.5 LSP3 LCL3
PTFNR/L2525M3 LST317 LCS3 P-2.5 LSP3 LCL3
PTFNR/L**25*4 LST42 LCS4 P-3 LSP4 LCL4

Reference pages
PSKNR/L: Inserts → B073 -, CBN → B166, PCD → B178
PTFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B243
Ext. Toolholder P C FN R /L
Le v e r l o c k t y pe to o l ho l d er f o r f aci ng w i t h 91° a p p roa c h a n gl e , n e ga t i v e 80° r h om b i c i n s e r t s

91°

b
f
f2
L2
L1

h1

h
Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert

PCFNR/L2020 20 20 125 28 20 25 18 0.8 CN**1204...
PCFNR/L2525 25 25 150 28 25 32 18 0.8 CN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PCFNR/L... LSC42 D30 LCS4 P-3 LSP4 LCL4

P D Q N R /L
Le v e r l o c k t y pe to o l ho l d er w i t h 1 0 7 .5 ° ap p roa c h a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
107.5°

f
L2 L1
h1

Cutting edge style Q h Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

PDQNR/L2525 25 25 150 32 25 32 0.8 DN**1504...

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PDQNR/L... LSD42 D30 LCS4 P-3 LSP4 LCL4

P R G N R /L
Le v e r l o c k t y p e to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e ro u n d i n s e r t s
45°
b
f

45° L2 L1
h1

Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

PRGNR/L2020 20 20 125 19 20 25 4.76 RNMG090300-61
PRGNR/L2525M4 25 25 150 25 25 32 6.35 RN**120400
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PRGNR/L2020 LSR32 LCS3 P-2.5 LSP3 LCL3
PRGNR/L2525M4 LSR42 LCS4 P-3 LSP4 LCL4

Reference pages
PCFNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178 -
PDQNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
PRGNR/L: Inserts → B072

B244 www.tungaloyamerica.com
P R G C R /L

Ext. Toolholder
Le v e r l o c k t y p e to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f
L1
30°

h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 h1 f Insert
PRGCR/L2020K10 20 20 125 20 25 RCMM1003...
PRGCR/L2525M12 25 25 150 25 32 RCM*1204...
PRGCR/L3225P16 32 25 170 32 32 RCM*1606...
PRGCR/L3232P20 32 32 170 32 40 RCM*2006...

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PRGCR/L2020K10 LSR32C LCS2 P-2 LSP3 LCL3C
PRGCR/L2525M12 LSR42C LCS3 P-2.5 LSP3 LCL4C
PRGCR/L3225P16 LSR53C LCS5 P-3 LSP4 LCL5C
PRGCR/L3232P20 LSR63C LCS5 P-3 LSP6C LCL6C

PRDCN
Le v e r l o c k t y p e to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f

L2
L1
h1

h
Cutting edge style D
Metric h b L1 L2 h1 f Insert
PRDCN2020K10 20 20 125 22 20 15 RCMM1003...
PRDCN2525M12 25 25 150 24 25 18.5 RCM*1204...
PRDCN3225P12 32 25 170 24 32 18.5 RCM*1204...
PRDCN3225P16 32 25 170 28 32 20.5 RCM*1606...
PRDCN3232P20 32 32 170 32 32 26 RCM*2006...
PRDCN4040R25 40 40 200 42 40 32.5 RCM*2507...

SPARE PARTS
Designation Shim Clamping screw Wrench Spring pin Lever
PRDCN2020K10 LSR32C LCS2 P-2 LSP3 LCL3C
PRDCN**25*12 LSR42C LCS3 P-2.5 LSP3 LCL4C
PRDCN3225P16 LSR53C LCS5 P-3 LSP4 LCL5C
PRDCN3232P20 LSR63C LCS5 P-3 LSP6C LCL6C
PRDCN4040R25 LSR84C LCS8C P-4 LSP6 LCL8C

Reference pages
PRGCR/L, PRDCN: Inserts → B126 -

Tungaloy B245
Ext. Toolholder M C LN R /L
M u l t i -c l a m p too l ho l d er w i t h 9 5 ° ap p ro ach a n gl e , f or n e ga t i v e 80° r h om b i c i n s e r t s

95° 45°

b
f
L2

f2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert

MCLNR/L 124B 0.750 0.750 4.500 1.250 0.750 1.000 0.708 0.031 CN**43...
MCLNR/L 164D 1.000 1.000 6.000 1.250 1.000 1.250 0.708 0.031 CN**43...
MCLNR/L 204D 1.250 1.250 6.000 1.250 1.250 1.500 0.708 0.031 CN**43...
MCLNR/L 165D 1.000 1.000 6.000 1.250 1.000 1.250 0.866 0.047 CN**54...
MCLNR/L 205D 1.250 1.250 6.000 1.250 1.250 1.500 0.866 0.047 CN**54...
MCLNR/L 206D 1.250 1.250 6.000 1.250 1.250 1.500 1.180 0.047 CN**64...
MCLNR/L 246D 1.500 1.500 6.000 1.250 1.500 2.000 1.180 0.047 CN**64...
MCLNR/L 866D 1.500 1.000 6.000 1.500 1.500 1.250 1.500 0.063 CN**64...

Metric h b L1 L2 h1 f f2 rε** Insert

MCLNR/L2525M12 25 25 150 32 25 32 18 0.8 CN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MCLNR/L 124B, 164D, 204D CK-20 KA54 STC20 ICSN433 P-3 P-2.5F
MCLNR/L 165D, 205D CK-12 KL58 STC4 ICSN533 P-4 P-3
MCLNR/L 206D, 246D, 866D CK-12 KL68 STC4 ICSN633 P-4 P-4
MCLNR/L2525M12 MCPM-21 MLP46 MCS625-3 MSC-432 P-3 P-2.5F

M W LN R /L
M u l t i - c l a m p to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i g o n i n s e r t s
25°
95°

b
f

L2 L1
95°
h1

Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

MWLNR/L 124B 0.750 0.750 4.500 1.130 0.750 1.000 0.031 WN**43...
MWLNR/L 164D 1.000 1.000 6.000 1.130 1.000 1.250 0.031 WN**43...
MWLNR/L 205D 1.250 1.250 6.000 1.130 1.250 1.500 0.031 WN**54...
MWLNR/L 205F 1.250 1.250 8.000 1.500 1.250 1.500 0.047 WN**54...
MWLNR/L 245X 1.500 1.500 10.00 1.500 1.500 1.750 0.047 WN**54...

Metric h b L1 L2 h1 f rε** Insert

MWLNR2020K08 20 20 125 25 20 25 0.8 WN**0804...
MWLNR/L2525M08 25 25 150. 25 25 32 0.8 WN**0804...
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench
MWLNR/L 124B CK-21 KL46 STC-20 P-2.5 P-2.5
MWLNR/L 164D CK-21 KL46 STC-4 P-2.5 P-2.5
MWLNR/L 205D, 245D CK-9 NL58 XNS-59 P-4 P-4
MWLNR2020K08,
MCPM-6 MLP46 MCS520-2.5 MSW-432 P-2.5
MWLNR/L2525M08

Reference pages
MCLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178
MWLNR/L: Inserts → B097 -, CBN → B167

B246 www.tungaloyamerica.com
MV JN R /L

Ext. Toolholder
Mu l t i -c l a m p to o l h o l d er w i t h 9 3 ° ap p ro ach an gl e , f or n e ga t i v e 35° or 25° r h om b i c i n s e r t s

b
f
L2
50° L1
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

MVJNR/L 123B 0.750 0.750 4.500 1.500 0.750 1.000 0.031 V/YN**33....
MVJNR/L 163D 1.000 1.000 6.000 1.500 1.000 1.250 0.031 V/YN**33....
MVJNR/L 203D 1.250 1.250 6.000 1.500 1.250 1.500 0.031 V/YN**33....

Metric h b L1 L2 h1 f rε** Insert

MVJNR/L2020K16 20 20 125 42 20 25 0.8 V/YN**1604...
MVJNR/L2525M16 25 25 150 42 25 32 0.8 V/YN**1604...
MVJNR/L3225P16 32 25 170 42 32 32 0.8 V/YN**1604...
MVJNR/L3232P16 32 32 170 42 32 40 0.8 V/YN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MVJNR/L 123B, 163D CK-43 KL-34L STC4 IVSN322 P-3 P-2F
MVJNR/L 203D CK-43 KL-34L STC4 IVSN322 P-4 P-2F
MVJNR/L**16 MCPM-22 MLP34L MCS625-3 MSV-322 P-3 P-2F

MD JN R
Mu l t i -c l a m p to o l h o l d er w i t h 9 3 ° ap p ro ach an gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

30°
b
f
f2

L2
30°

93°
L1
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert

MDJNR/L 124B 0.750 0.750 4.500 1.250 0.750 1.000 0.748 0.031 DN**43...
MDJNR/L 164D 1.000 1.000 6.000 1.250 1.000 1.250 0.748 0.031 DN**43...
MDJNR/L 204D 1.250 1.250 6.000 1.250 1.250 1.500 0.748 0.031 DN**43...
MDJNR/L 165D 1.000 1.000 6.000 1.500 1.000 1.250 0.866 0.047 DN**54...
MDJNR/L 205D 1.250 1.250 6.000 1.500 1.250 1.500 0.936 0.047 DN**54...
MDJNR/L 245D 1.500 1.500 6.000 1.500 1.500 2.000 0.936 0.047 DN**54...

Metric h b L1 L2 h1 f f2 rε** Insert

MDJNR2525M15 25 25 150 38 25 32 19 0.8 DN**15...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MDJNR/L 124B, 164D, 204D CK20 KL46L STC20 IDSN433 P-3 P-2.5F
MDJNR/L 165D, 205D CK12 KL58 STC4 IDSN533 P-4 P-2.5F
MDJNR2525M15 MCPM-22 MLP46L MCS625-3 MSD-432 P-3 P-2.5F

Reference pages
MVJNR/L: Inserts → B093 -, B104 -, CBN → B167 -, PCD → B178
MDJNR: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B247
Ext. Toolholder M TJN R /LS
M u l t i - c l a m p to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
25° L2 L1
93°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

MTJNR/LS 123 0.750 0.750 4.500 1.000 0.750 1.000 0.031 TN**33...
MTJNR/LS 163 1.000 1.000 6.000 1.000 1.000 1.250 0.031 TN**33...
MTJNR/LS 164 1.000 1.000 6.000 1.250 1.000 1.250 0.031 TN**43...
MTJNR/LS 204 1.250 1.250 6.000 1.250 1.250 1.500 0.031 TN**43...
MTJNR/LS 205 1.250 1.250 6.000 1.500 1.250 1.500 0.047 TN**54...

Metric h b L1 L2 h1 f rε** Insert

MTJNR2525M16 25 25 150 28 25 32 0.8 TN**16...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MTJNR/LS 123, 164 CK-6 KL34L STC5 ITSN323 P-3 P-2F
MTJNR/LS 164, 204 CK-9 KL46 STC4 ITSN433 P-4 P-2.5F
MTJNR/LS 205 CK-9 KL58 STC4 ITSN534 P-4 P-3
MTJNR2525M16 MCPM-21 MLP34L MCS625-3 MST-322 P-3 P-2F

M V VN N
M u l t i -c l a m p to o l ho l d er w i t h 7 2 .5 ° ap p ro ac h a n gl e , f or n e ga t i v e 35° or 25° r h om b i c i n s e r t s

b
f

L2
72.5° L1
h1

Cutting edge style V

Inch h b L1 L2 h1 f rε** Insert
MVVNN 123B 0.750 0.750 4.000 1.810 0.750 0.375 0.031 VN**33...
MVVNN 163D 1.000 1.000 6.000 1.810 1.000 0.500 0.031 VN**33...

Metric h b L1 L2 h1 f rε** Insert

MVVNN2020K16 20 20 125 48 20 10 0.8 V/YN**1604...
MVVNN2525M16 25 25 150 48 25 12.5 0.8 V/YN**1604...
MVVNN3225P16 32 25 170 48 32 12.5 0.8 V/YN**1604...
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MVVNN 123B, 163D CK-43 KL34L STC4 IVSN322 P-3 P-2F
MVVNN**16 MCPM-30 MLP34L MCS828-4 MSV-322 P-4 P-2F

Reference pages
MTJNR: Inserts → B082 -, CBN → B166 -, PCD → B178
MVVNN: Inserts → B093 -, B104, CBN → B167 -, PCD → B178

B248 www.tungaloyamerica.com
MD PN N

Ext. Toolholder
M u l t i -c l a m p to o l h o l d er w i t h 6 2 .5 ° ap p ro ach a n gl e , f or n e ga t i v e 55° r h om b i c i n s e r t s

b
f
L2
62.5º L1

h1

h
Cutting edge style P
Inch h b L1 L2 h1 f rε** Insert
MDPNN164D 1.000 1.000 6.000 1.630 0.500 0.500 0.031 DN**43...

Metric h b L1 L2 h1 f rε** Insert

MDPNN2525M15 25 25 150 42 25 12.5 0.8 DN**1504...
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MDPNN164D CK-20 KL46L STC-20 INSN433 P-3 P-2.5F
MDPNN2525M15 MCPM-22 MLP46L MCS625-3 MSD-432 P-3 P-2.5F

MTEN N S
M u l t i - c l a m p to o l h o l d e r w i t h 6 0 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f

L2 L1
60°
h1

h
Cutting edge style E
Inch h b L1 L2 h1 f rε** Insert
MTENNS 103 0.625 0.625 4.500 1.250 0.625 0.312 0.031 TN**32...
MTENNS 123 0.750 0.750 4.500 1.250 0.750 0.375 0.031 TN**32...
MTENNS 164 1.000 1.000 6.000 1.500 1.000 0.500 0.031 TN**43...
MTENNS 205 1.250 1.250 6.000 1.620 1.250 0.625 0.047 TN**54...

Metric h b L1 L2 h1 f rε** Insert

MTENN2525M16 25 25 150 35 25 12.5 0.8 TN**16...
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MTENNS 103, 123 CK-6 KL34L STC5 ITSN323 P-3 P-2F
MTENNS 164 CK-9 KL46 STC4 ITSN433 P-4 P-2.5F
MTENNS 205 CK-12 KL58L STC4 ITSN534 P-4 P-3F
MTENN2525M16 MCPM-21 MLP34L MCS625-3 MST-322 P-3 P-2F

Reference pages
MDPNN: Inserts → B063 -, CBN → B165 -, PCD → B178
MTENN: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B249
Ext. Toolholder M TQN R
M u l t i - c l a m p to o l h o l d e r w i t h 1 0 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
105°
L2
L1
105°

h1

h
Cutting edge style Q Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

MTQNR2020K16 20 20 125 26 20 25 0.8 TN**16...
MTQNR2525M16 25 25 150 26 25 32 0.8 TN**16...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MTQNR... MCPM-21 MLP34L MCS625-3 MST-322 P-3 P-2F

M VQN R /L
M u l t i -c l a m p too l ho l d er w i t h 1 1 7 .5 ° ap p ro a c h a n gl e , f or n e ga t i v e 35° or 25° r h om b i c i n s e r t s

b
f

117.5°

L2 L1
117.5°
h1

h
Cutting edge style Q Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

MVQNR/L2020K16 20 20 125 40 20 25 0.8 V/YN**1604...
MVQNR/L2525M16 25 25 150 40 25 32 0.8 V/YN**1604...
MVQNR/L3232P16 32 32 170 40 32 40 0.8 V/YN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Right-left screw Shim Wrench 1 Wrench 2
MVQNR/L... MCPM-22 MLP34L MCS625-3 MSV-322 P-3 P-2F

Reference pages
MTQNR: Inserts → B082 -, CBN → B166 -, PCD → B178
MVQNR/L: Inserts → B93 -, B104, CBN → B167 -, PCD → B178

B250 www.tungaloyamerica.com
Replacement Parts for M-type Toolholders
¡When using the inserts shown in the shaded cells, the optional parts shown in the shaded cells are needed. You may purchase them separately.

Ext. Toolholder
¡1) Used for 1616H16. ¡2) Used for MSDNN. ¡3) Used for MDJNR/L ¡4) Used for MVVNN

Clamping Chipbreaker Lock pin

Applicable inserts Shim Lock pin Shim screw Clamp screw piece Wrench Wrench
Toolholders

Shape
Designation Designation

MSDNN 103 SN32 KL34 - CBS-4M P-2.5F P-3

MSSNR/L 123 ISSN 322 CK-6 STC5 2)
SN32 - KAS3 CBS-4MN (P-2.5F) P-3

124 SN43 ISSN 433 - KAS4 CBS-4M

164 CK-9 STC4 P-2.5F P-3
2)
SN43 ISSN 433 KL46 - CBS-4MN

MTGNR/L 103 TN33 KL34L - 1) 1)

MTJNR/L 123 ITSN 323 CK-6 STC5 CBT-3M P-2F P-3
MTENN 163 TN33 - KAS3

TN32 KL34L - 2) 2)
ITSN 333 CK-6 STC5 CBT-3M P-2F P-3
TN32 - KAS3

164 TN43 ITSN 433 - KAS4 CK-9 STC4 CBT-3M (P-2F) P-3
204
2525M22 TN43 KL46 -
3225P22 ITSN 433 CK-9 STC4 CBT-4M P-2.5F P-4
3232P22 TN43 - KAS4

205
TN54 ITSN 534 KL58 -
KAS5 CK-9 STC4 - P-3 P-4

246 TN66 ITSN 636 KL68L -

KAS6 CK-12 STC4 - P-3 P-4

MCLNR/L 124 CN43 ICSN 433 - KAS4

164 CK-20 STC20 CBC-4MN P-2.5F P-3
204 CN43 ICSN 433 KL46L -

165
205 CN54 ICSN 533
KL58 - CK-12 STC4 - P-3 P-4

206 CN64 ICSN 633 KL68 - CK-12 STC4 - P-4 P-4

246
124 DN44 IDSN 433 -
3)

164 KL46L CBD-4MR/L

204 DN43 IDSN 443 - CK-20 STC20 P-2.5F P-3
CBD-4MN
MDJNR/L
MDPNN DN43 IDSN 443 - KAS54

3)
DN44 IDSN 433 - KAS54 CK-20 STC20 CBD-4MR/L
CBD-4MN P-2.5F P-3

Tungaloy B251
 Replacement Parts for M-type Toolholders
Ext. Toolholder
Clamping Chipbreaker Lock pin
Applicable inserts Shim Lock pin Shim screw Clamp screw piece Wrench Wrench
Toolholders

Shape
Designation Designation

MVJNR/L 123 CK-43 STC4 P-3

MVVNN 163 VN33 IVSN322 KL34L KAS3 - P-2F
4) 4) 4)
MVQNR/L 203 P-4

MRGNR/L 124B RN43 KL46 -

164D IRSN-43 CK-21 STC20 CBR-4MN P-2.5F P-3
RN43 - KAS4 STC4

RN45 IRSN-42 - KAS4 CK-21 STC20 CBR-4MN P-2.5F P-3

STC4
MWLNR/L 124
164 WN43 IWSN-433 KL46 - CK-21 STC20 - P-2.5 P-2.5
STC4

205
WN53 IWSN-533 NL58 - CK-9 XNS-59 - P-4 P-4

Note : The shims are made of Tungaloy grade D30, and the chipbreaker pieces are of TX30.

List of Chipbreaker Pieces

In addition to the standard chipbreaker pieces, optional chipbreaker pieces are available separately.
Select the proper one that is suitable for your cutting conditions.
Dimensions (in) Chipbreaker
width when
Shape Designation Inserts assembled
A T
(in)
T CBS-4S 0.457 0.059
SN43
CBS-4M 0.417 0.098 0.098
SN45
A

CBS-4L 0.358 0.157

T CBS-4SN 0.453 0.059
SN43
CBS-4MN 0.413 0.098 0.098
A

SN45
CBS-4LN 0.354 0.157
CBT-3S 0.476 0.059
TN33
T CBT-3M 0.437 0.098 0.098
TN35
CBT-3L 0.398 0.138
A

CBT-4S 0.665 0.059

CBT-4M TN43 0.626 0.098 0.098
CBT-4L 0.567 0.138

T CBC-4SN 0.453 0.059

CN43
CBC-4MN 0.413 0.098 0.098
CN45
A

CBC-4LN 0.374 0.138

T CBD-4SR/L DN43 0.453 0.059

CBD-4MR/L DN44 0.413 0.098 0.098
A

CBD-4LR/L DN45 0.374 0.138

T CBD-4SN 0.453 0.059
CBD-4MN DN44 0.413 0.098 0.098
A

CBD-4LN 0.374 0.138

T
CBR-4SN RN43 0.469 0.059
0.098
RN44
A

CBR-4MN 0.429 0.098

B252 www.tungaloyamerica.com
ETAN R

Ext. Toolholder
P i n l o c k to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

30°

b
f
91° L1

h1

h
Cutting edge style A Right hand (R) shown.

Metric h b L1 h1 f rε** Insert

ETANR1616H33 16 16 100 15.5 16 0.8 TN**1604...
ETANR2020K33 20 20 125 19.5 20 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Wrench
ETANR1616H33 ER3 P332US KY40
ETANR2020K33 ER3 P333US KY40

ETG N R /L
P i n l o c k to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f

L1
91°
h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 h1 f rε** Insert

ETGNR/L1212 12 12 80 11.5 16 0.4 TN**1103...
ETGNR/L1616H33 16 16 100 15.5 20 0.8 TN**1604...
ETGNR/L2020K33 20 20 125 19.5 25 0.8 TN**1604...
ETGNR/L2020K33W 20 20 125 19.5 25 0.8 TN**1604...
ETGNR2525M33 25 25 150 24.5 32 0.8 TN**1604...
ETGNR/L2525M33W 25 25 150 24.5 32 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Shim Wrench
ETGNR/L1212 ER2 P221US - KY25
ETGNR/L1616H33 ER3 P332US - KY40
ETGNR/L2020K33 ER3 P333US - KY40
ETGNR/L2020K33W ER3 P333WS EST32 KY40
ETGNR2525M33 ER3 P334US - KY40
ETGNR/L2525M33W ER3 P334WS EST32 KY40

Reference pages
ETANR, ETGNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B253
Ext. Toolholder E TEN N
P i n l o c k to o l h o l d e r w i t h 6 0 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f

30°
60° L1

h1

h
Cutting edge style E
Metric h b L1 h1 f rε** Insert
ETENN1212 12 12 80 11.5 6 0.4 TN**1103...
ETENN1616H33 16 16 100 15.5 8 0.8 TN**1604...
ETENN2020K33 20 20 125 19.5 10 0.8 TN**1604...
ETENN2020K33W 20 20 125 19.5 10 0.8 TN**1604...
ETENN2525M33W 25 25 150 24.5 12.5 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Shim Wrench
ETENN1212 ER2 P221US - KY25
ETENN1616H33 ER3 P332US - KY40
ETENN2020K33 ER3 P333US - KY40
ETENN2020K33W ER3 P333WS EST32 KY40
ETENN2525M33W ER3 P334WS EST32 KY40

E S D N R /L
P i n l o c k to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s
f

b
h1 L1
45°
h

Cutting edge style D Right hand (R) shown.

Metric h b L1 h1 f rε** Insert

ESDNR1212 12 12 80 11.5 6 0.8 SN**0903...
ESDNR1616H32 16 16 100 15.5 8 0.8 SN**0903...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Wrench
ESDNR1212 ER3 P321US KY40
ESDNR1616H32 ER3 P322US KY40

Reference pages
ETENN: Inserts → B082 -, CBN → B166 -, PCD → B178
ESDNR/L: Inserts →B073 -

B254 www.tungaloyamerica.com
ESSN R /L

Ext. Toolholder
P i n l o c k to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

45°

b
f
L1
h
45°
h1
Cutting edge style S Right hand (R) shown.

Metric h b L1 h1 f rε** Insert

ESSNR1616H32 16 16 100 15.5 20 0.8 SN**0903...
ESSNR2020W 20 20 125 19.5 25 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Shim Wrench
ESSNR1616H32 ER3 P322US - KY40
ESSNR2020W ER3 P433W ESS42 KY40

ETX N R /L
P i n l o c k to o l h o l d e r w i t h 1 0 0 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

25°
100°

b
f

L1
h

100°
h1
Cutting edge style X Right hand (R) shown.

Metric h b L1 h1 f rε** Insert

ETXNL1616H33 16 16 100 15.5 20 0.8 TN**1604...
ETXNR2020K33 20 20 125 19.5 25 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation E-ring Pin Wrench
ETXNL1616H33 ER3 P332US KY40
ETXNR2020K33 ER3 P333US KY40

Reference pages
ESSNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178
ETXNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B255
Ext. Toolholder C K JN R /L
C l a m p -o n to o l ho l d er w i t h 9 3 ° ap p ro ach an gl e , f or n e ga t i v e 55° p a ra l l e l ogra m i n s e r t s
32°

b
f
L2
95° 30° L1

h1

h
Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CKJNR/L2525 25 25 150 32 25 32 0.8 KNMX1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Clamping screw Shim screw Shim Spring Wrench
CKJNR2525 CPK5R BP-490 CTS-M6 SM3X0.5X10 CSK54R SP913 P-4
CKJNL2525 CPK5L BP-490 CTS-M6 SM3X0.5X10 CSK54L SP913 P-4

CTG N R /L
C l a m p - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

60°

b
f
L2 L1
91° h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CTGNR/L2020 20 20 125 28.5 20 25 0.8 TN**1604...
CTGNR/L2525 25 25 150 28.5 25 32 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CTGNR/L... NCT-2M NF-84A NDS-8A SM3X0.5X8 NAT-32 P-4

C S B N R /L
C l a m p - o n to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s
b
f

L2
L1
75°
h1

Cutting edge style B Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CSBNR2020 20 20 125 31 20 17 0.8 SN**1204...
CSBNR/L2525 25 25 150 31 25 22 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CSBNR/L... NCS-3M NF-84A NDS-8A SM3X0.5X8 NAS-42 P-4

Reference pages
CKJNR/L: Inserts → B105
CTGNR/L: Inserts → B092 -, CBN → B175
CSBNR/L: Inserts → B081, CBN → B175, PCD → B178

B256 www.tungaloyamerica.com
CSD N N

Ext. Toolholder
C l a m p - o n to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

b
L2
45°
L1

h1

h
Cutting edge style D
Metric h b L1 L2 h1 f rε** Insert
CSDNN2020 20 20 125 32 20 10 0.8 SN**1204...
CSDNN2525 25 25 150 32 25 12.5 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CSDNN... NCS-3MN NF-84A NDS-8A SM3X0.5X8 NAS-42 P-4

CSSN R /L
Cla m p -o n to o l h o l d er w i t h 4 5 ° ap p ro ach angl e (S - s t y l e ), f or n e ga t i v e s q u a re i n s e r t s

45°

b
f
h1

45° L2
L1
h

Cutting edge style S Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CSSNR/L2020 20 20 125 31 20 25 0.8 SN**1204...
CSSNR/L2525 25 25 150 31 25 32 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CSSNR/L... NCS-3M NF-84A NDS-8A SM3X0.5X8 NAS-42 P-4

CSK N R /L
C l a m p - o n to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s
15°
75°
b
f

L2
L1
h
h1

Cutting edge style K Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CSKNR/L2525 25 25 150 25 25 32 0.8 SN**1204...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CSKNR/L2525 NCS-3MN NF-84A NDS-8A SM3X0.5X8 NAS-42 P-4

Reference pages
CSDNN, CSSNR/L, CSKNR/L: Inserts → B081, CBN → B175, PCD → B178

Tungaloy B257
 CTFN R /L
C l a m p - o n to o l h o l d e r f o r f a c i n g w i t h 9 1 ° a p p ro a c h a n g l e , n e g a t i v e t r i a n g l e i n s e r t s
Ext. Toolholder
30°
91°

b
f
L2
L1

h11

h
Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CTFNR/L2020 20 20 125 22 20 25 0.8 TN**1604...
CTFNR/L2525 25 25 150 22 25 32 0.8 TN**1604...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp Clamping screw Shim screw Shim Wrench
CTFNR/L... NCT-2M NF-84A NDS-8A SM3X0.5X8 NAT-32 P-4

CTG PR /L
C l a m p - o n to o l h o l d e r w i t h 9 0 ° a p p ro a c h a n g l e , f o r p o s i t i v e t r i a n g l e i n s e r t s
5°

b
f
L2
L1
90°

h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CTGPR/L1616H3 16 16 100 23 16 20 0.8 TP**1603...
CTGPR/L2020K3 20 20 125 27 20 25 0.8 TP**1603...
CTGPR/L2525M3 25 25 150 27 25 32 0.8 TP**1603...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CTGPR/L1616H3 CBT-3M CSG-6L SM3X0.5X8 PAT-32 P-3
CTGPR/L2*2**3 CBT-3M CSG-8 SM3X0.5X8 PAT-32 P-4

C S B PR /L
C l a m p - o n to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e s q u a re i n s e r t s
b
f

L2 L1
75°
h1

Cutting edge style B Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CSBPR/L1616H3 16 16 100 25 16 13 0.4 SP**0903...
CSBPR/L2020K4 20 20 125 32 20 17 0.8 SP**1203...
CSBPR/L2525M4 25 25 150 32 25 22 0.8 SP**1203...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CSBPR/L1616H3 CBS-3M CSG-6L SM2.5X0.45X8 PAS-32 P-3
CSBPR/L2*2**4 CBS-4M CSG-8 SM3X0.5X8 PAS-42 P-4

Reference pages
CTFNR/L: Inserts → B092, CBN → B175
CTGPR/L: Inserts → B138 -, CBN → B172 -, PCD → B180
CSBPR/L: Inserts → B132, CBN → B170 -, PCD → B179

B258 www.tungaloyamerica.com
CSD P N
C l a m p - o n to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e s q u a re i n s e r t s

Ext. Toolholder
b
f
L2 L1
45°

5°
h1

h
Cutting edge style D
Metric h b L1 L2 h1 f rε** Insert
CSDPN1616H3 16 16 100 26 16 8 0.8 SP**0903...
CSDPN2020K4 20 20 125 34 20 10 0.8 SP**1203...
CSDPN2525M4 25 25 150 34 25 12.5 0.8 SP**1203...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CSDPN1616H3 CBS-3MN CSG-6L SM2.5X0.45X8 PAS-32 P-3
CSDPN2*2**4 CBS-4MN CSG-8 SM3X0.5X8 PAS-42 P-4

CSSP R
C l a m p - o n to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e s q u a re i n s e r t s

45°

b
f
h1 L2 L1
h
45°

Cutting edge style S Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CSSPR1616H3 16 16 105.5 23 16 20 0.8 SP**0903...
CSSPR2020K4 20 20 133 28 20 25 0.8 SP**1203...
CSSPR2525M4 25 25 158 28. 25 32 0.8 SP**1203...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CSSPR1616H3 CBS-3M CSG-6L SM2.5X0.45X8 PAS-32 P-3
CSSPR2*2**4 CBS-4M CSG-8 SM3X0.5X8 PAS-42 P-4

CT FP R /L
Cla m p -o n to o l h o l d er f o r f aci ng w i t h 9 1 ° ap p roa c h a n gl e , p os i t i v e t r i a n gl e i n s e r t s
b
11°

91°
f

5°
L2
h1 L1
h1

Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CTFPR/L1616H3 16 16 100 23 16 20 0.8 TP**1603...
CTFPR/L2020K3 20 20 125 26 20 25 0.8 TP**1603...
CTFPR/L2525M3 25 25 150 26 25 32 0.8 TP**1603...
**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CTFPR/L1616H3 CBT-3M CSG-6L SM3X0.5X8 PAT-32 P-3
CTFPR/L2*2**3 CBT-3M CSG-8 SM3X0.5X8 PAT-32 P-4

Reference pages
CSDPN, CSSPR: Inserts → B132, CBN → B170 -, PCD → B179
CTFPR/L: Inserts → B145 -, CBN → B172 -, PCD → B180

Tungaloy B259
Ext. Toolholder CTC P R /L
C l a m p -o n to o l ho l d er f o r f aci ng w i t h 9 0 ° a p p roa c h a n gl e , p os i t i v e t r i a n gl e i n s e r t s

b
f
L2 L1
30

h1

h
Cutting edge style C Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

CTCPR/L2525M3 25 25 150 32 25 32 0.8 TP**1603...

**rε: Standard corner radius

SPARE PARTS
Designation Chipbreaker piece Clamp set Shim screw Shim Wrench
CTCPR/L2525M3 CBT-3M CSW-2 SM3X0.5X8 PAT-32 P-4

W TJN R /L
We d g e - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e , f o r n e g a t i v e t r i a n g l e i n s e r t s

b
f
25° L2 L1
93° h1

h
Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

WTJNR2020 20 20 125 31 20 25 0.8 TN**1604...
WTJNR/L2525M3 25 25 150 31 25 32 0.8 TN**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp E-ring Nut Pin Clamping screw Shim Wrench
WTJNR2020 WCW3 5103-25 WCN3S WCP3S WCS3 WST33 P-3
WTJNR/L2525M3 WCW3 5103-25 WCN3 WCP3S WCS3 WST33 P-3

H S R N R /L
R e t ra c t - p i n c l a m p to o l h o l d e r w i t h 7 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s
b
f

L2 L1
75°
h1

Cutting edge style R Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

HSRNR/L4040R 40 40 200 50 40 43 1.6 SNMM3109...
HSRNR/L5050S 50 50 250 60 50 53 1.6 SNMM3109...

**rε: Standard corner radius

SPARE PARTS
Designation Pin Clamping screw Shim Wrench
HSRNR/L... SW99 LS-8 NAS-04 P-4

Reference pages
CTCPR/L: Inserts → B145 -, CBN → B172 -, PCD → B180
WTJNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

B260 www.tungaloyamerica.com
SC LC R /L

Ext. Toolholder
Scre w -o n c l a m p to o l ho l d er w i t h 9 5 ° ap p ro ac h a n gl e , f or p os i t i v e 80° r h om b i c i n s e r t s

95°
95°

bb
ff
L22
L11
95°
95°

hh11

hh
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SCLCR/L 103 0.625 0.625 4.000 0.625 0.625 0.750 0.031 CC**32.5...
SCLCR/L 123 0.750 0.750 4.500 0.625 0.750 0.750 0.031 CC**32.5...
SCLCR/L 163 1.000 1.000 6.000 0.625 1.000 0.750 0.031 CC**32.5...
SCLCR/L 124B 0.750 0.750 4.500 0.625 0.750 0.750 0.031 CC**43...
SCLCR/L 164D 1.000 1.000 6.000 0.750 1.000 0.750 0.031 CC**43...

Metric h b L1 L2 h1 f rε** Insert

SCLCR/L1616H09 16 16 100 16 16 20 0.8 CC**09T3...
SCLCR/L2020K12 20 20 125 20 20 25 0.8 CC**1204...
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SCLCR/L103, 123, 163
CSTB-3.5L DTS5-3.5 SSC32 P-3.5 T-15F
SCLCR/L1616H09
SCLCR/L124B, 164D
CSTB-4F DTS6-4 SSC4T3 P-4 T-15F
SCLCR/L2020K12

SD JC R /L
Scre w -o n c l a m p to o l ho l d er w i t h 9 3 ° ap p ro ac h a n gl e , f or p os i t i v e 55° r h om b i c i n s e r t s

b
f

L2
30° L1
93°
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SDJCR/L 062 0.375 0.375 2.500 0.625 0.375 0.500 0.016 DC**21.5...
SDJCR/L 082 0.500 0.500 3.500 0.625 0.500 0.625 0.016 DC**21.5...
SDJCR/L 083 0.500 0.500 3.500 - 0.500 0.625 0.016 DC**32.5...
SDJCR/L 103 0.625 0.625 4.000 - 0.625 0.750 0.031 DC**32.5...
SDJCR/L 123 0.750 0.750 4.500 - 0.750 1.000 0.031 DC**32.5...
SDJCR/L 163 1.000 1.000 6.000 - 1.000 1.250 0.031 DC**32.5...

Metric h b L1 L2 h1 f rε** Insert

SDJCR1616H11 16 16 100 20 16 20 0.8 DC**11T3...
SDJCR/L2020K11 20 20 125 20.5 20 25 0.8 DC**11T3...
SDJCR/L2525M11
**rε: Standard corner radius 25 25 150 21.5 25 32 0.8 DC**11T3...

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SDJCR/L 062, 082 CSTB-2.5 DTS5-3.5 SSD32 P-3.5 T-15F
SDJCR/L 083, 103,
123, 163
CSTB-3.5L DTS5-3.5 SSD32 P-3.5 T-15F
SDJCR/L1616..., 2020...,
2525...

Reference pages
SCLCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179
SDJCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B261
Ext. Toolholder SV JC R /L
Sc re w -o n c l a mp to o l ho l d er w i t h 9 3 ° ap p roa c h a n gl e , f or p os i t i v e 35° r h om b i c i n s e r t s

b
f
L2 L1
93° 50°

h1

h
Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SVJCR/L103 0.625 0.625 4.500 1.000 0.625 0.725 0.031 VC**33...
SVJCR/L123 0.750 0.750 4.500 1.250 0.750 0.955 0.031 VC**33...
SVJCR/L163 1.000 1.000 6.000 1.500 1.000 1.250 0.031 VC**33...

Metric h b L1 L2 h1 f rε** Insert

SVJCR/L1616H16 16 16 100 32 16 20 0.8 VC**1604...
SVJCR/L2020K16 20 20 125 32 20 25 0.8 VC**1604...
SVJCR/L2525M16 25 25 150 40 25 32 0.8 VC**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SVJCR/L... CSTB-3.5L DTS5-3.5 SSV32 P-3.5 T-15F

SD N C N
Sc re w -o n c l a mp to o l ho l d er w i t h 6 2 .5 ° ap p roa c h a n gl e , f or p os i t i v e 55° r h om b i c i n s e r t s

b
f

62.5° L2 L1
h1

Cutting edge style N

Metric h b L1 L2 h1 f rε** Insert
SDNCN1616H11 16 16 100 21 16 8 0.8 DC**11T3...
SDNCN2020K11 20 20 125 21 20 10 0.8 DC**11T3...
SDNCN2525M11 25 25 150 21 25 12.5 0.8 DC**11T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SDNCN... CSTB-3.5L DTS5-3.5 SSD32 P-3.5 T-15F

Reference pages
SVJCR/L: Inserts → B149 -, CBN → B171 -, PCD → B179 -
SDNCN: Inserts → B116 -, CBN → B170 -, PCD → B179

B262 www.tungaloyamerica.com
S VV C N

Ext. Toolholder
S c re w -o n c l a m p to o l ho l d er w i t h 7 2 .5 ° ap p ro a c h a n gl e , f or p os i t i v e 35° r h om b i c i n s e r t s

b
L1
72.5°

h1

h
Cutting edge style V
Metric h b L1 h1 f rε** Insert
SVVCN2020K16 20 20 125 20 10 0.8 VC**1604...
SVVCN2525M16 25 25 150 25 12.5 0.8 VC**1604...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SVVCN... CSTB-3.5L DTS5-3.5 SSV32 P-3.5 T-15F

STAC R /L
S c re w - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r p o s i t i v e t r i a n g l e i n s e r t s

b
f

L2
L1
91°
h

Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

STACR/L1616H16 16 16. 100 22.5 16 16 0.8 TC**16T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
STACR/L... CSTB-3.5L DTS5-3.5 SST32 P-3.5 T-15F

Reference pages
SVVCN: Inserts → B149 -, CBN → B171 -, PCD → B179 -
STACR/L: Inserts → B133 -

Tungaloy B263
Ext. Toolholder SR AC R /L
S c re w - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f
L2 L1

h1

h
Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f Insert
SRACR1010H05 10 10 100 10 10 10.3 RCMT0502...
SRACR/L1212H05 12 12 100 10 12 12.3 RCMT0502...
SRACR/L1212H06 12 12 100 12 12 12.4 RC*T0602...
SRACR1616H05 16 16 100 10 16 16.3 RCMT0502...
SRACR/L1616H06 16 16 100 12 16 16.4 RC*T0602...
SRACR/L1616H08 16 16 100 16 16 16.5 RC*T0803...
SRACR/L2020K05 20 20 125 10 20 20.3 RCMT0502...
SRACR/L2020K06 20 20 125 12 20 20.4 RC*T0602...
SRACR/L2020K08 20 20 125 16 20 20.5 RC*T0803...
SRACR/L2525M05 25 25 150 10 25 25.3 RCMT0502...
SRACR/L2525M06 25 25 150 12 25 25.4 RC*T0602...
SRACR/L2525M08 25 25 150 16 25 25.5 RC*T0803...

SPARE PARTS
Designation Clamping screw Wrench
SRACR/L1*1*H05 CSTB-2.2R T-7F
SRACR/L1212H06 CSTB-2.5 T-8F
SRACR1616H05 CSTB-2.2R T-7F
SRACR/L1616H06 CSTB-2.5 T-8F
SRACR/L1616H08 CSTB-3 T-9F
SRACR/L2020K05 CSTB-2.2R T-7F
SRACR/L2020K06 CSTB-2.5 T-8F
SRACR/L2020K08 CSTB-3 T-9F
SRACR/L2525M05 CSTB-2.2R T-7F
SRACR/L2525M06 CSTB-2.5 T-8F
SRACR/L2525M08 CSTB-3 T-9F

Reference pages
SRACR/L: Inserts → B126 -

B264 www.tungaloyamerica.com
S R G C R /L

Ext. Toolholder
S c re w - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f
L2
L1
30°

h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f Insert
SRGCR1212H05 12 12 100 9.5 12 16 RCMT0502...
SRGCR/L1212H06 12 12 100 10 12 16 RC*T0602...
SRGCR/L1616H05 16 16 100 9.5 16 20 RCMT0502...
SRGCR/L1616H06 16 16 100 10 16 20 RC*T0602...
SRGCR/L1616H08 16 16 100 11 16 20 RC*T0803...
SRGCR/L2020K05 20 20 125 11.2 20 25 RCMT0502...
SRGCR/L2020K06 20 20 125 12 20 25 RC*T0602...
SRGCR/L2020K08 20 20 125 12.7 20 25 RC*T0803...
SRGCR/L2020K10 20 20 125 14 25 25 RC*T1003...
SRGCR/L2525M05 25 25 150 14.7 25 32 RCMT0502...
SRGCR/L2525M06 25 25 150 15 25 32 RC*T0602...
SRGCR/L2525M08 25 25 150 16.2 25 32 RC*T0803...
SRGCR/L2525M10 25 25 150 17.5 25 32 RC*T1003...

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SRGCR1212H05 CSTB-2.2R - - - T-7F
SRGCR/L1212H06 CSTB-2.5 - - - T-8F
SRGCR/L1616H05 CSTB-2.2R - - - T-7F
SRGCR/L1616H06 CSTB-2.5 - - - T-8F
SRGCR/L1616H08 CSTB-3 - - - T-9F
SRGCR/L2020K05 CSTB-2.2R - - - T-7F
SRGCR/L2020K06 CSTB-2.5 - - - T-8F
SRGCR/L2020K08 CSTB-3 - - - T-9F
SRGCR/L2020K10 CSTB-3.5L DTS5-3.5 SSR32 P-3.5 T-15F
SRGCR/L2525M05 CSTB-2.2R - - - T-7F
SRGCR/L2525M06 CSTB-2.5 - - - T-8F
SRGCR/L2525M08 CSTB-3 - - - T-9F
SRGCR/L2525M10 CSTB-3.5L DTS5-3.5 SSR32 P-3.5 T-15F

Reference pages
SRGCR/L: Inserts → B126 -

Tungaloy B265
Ext. Toolholder SSD C /P N
S c re w - o n c l a m p to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e s q u a re i n s e r t s

b
f
45° 45° L2
L1

h1

h
Cutting edge style D
Metric h b L1 L2 h1 f rε** Insert
SSDCN1010K07 10 10 125 12 10 5 0.4 SC**0702...
SSDPN1010H 10 10 100 12 10 5 0.4 SP*P042...
SSDCN1212K09 12 12 125 15 12 6 0.8 SC**09T3...
SSDPN1212H 12 12 100 12 12 6 0.4 SP*P042...
SSDCN1616H09 16 16 100 15 16 8 0.8 SC**09T3...
SSDPN1616H 16 16 100 14 16 8 0.8 SP*M322...
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SSDCN1010K07 CSTB-3 - - - T-9F
SSDPN1010H CSTA-NO3 - - - T-9F
SSDCN1212K09 CSTB-4 - - - T-15F
SSDPN1212H CSTA-NO3 - - - T-9F
SSDCN1616H09 CSTB-3.5L DTS5-3.5 SSS32 P-3.5 T-15F
SSDPN1616H CSTA-NO5 - - - T-9F

SR D C N
S c re w - o n to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f

L2
L1
h1

Cutting edge style D

Metric h b L1 L2 h1 f Insert
SRDCN1212K08 12 12 125 16 12 10 RC*T0803...
SRDCN1212K10 12 12 125 20.3 12 11 RC*T1003...
SRDCN1616M08 16 16 150 16 16 12 RC*T0803...
SRDCN1616M10 16 16 150 20.3 16 13 RC*T1003...
SRDCN2020K06 20 20 125 12 20 13 RC*T0602...
SRDCN2020K08 20 20 125 16 20 14 RC*T0803...
SRDCN2020K10 20 20 125 20.3 25 15 RC*T1003...
SRDCN2525M06 25 25 150 12 25 15.5 RC*T0602...
SRDCN2525M08 25 25 150 16 25 16.5 RC*T0803...
SRDCN2525M10 25 25 150 20.3 25 17.5 RC*T1003...

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SRDCN**08 CSTB-3 - - - T-9F
SRDCN**10 CSTB-3.5L DTS5-3.5 SSR32 P-3.5 T-15F
SRDCN2**06 CSTB-2.5 - - - T-8F

Reference pages
SSDC/PN: Inserts → B129, E094
SRDCN: Inserts → B126 -

B266 www.tungaloyamerica.com
S D Q C R /L

Ext. Toolholder
S c re w -o n c l a m p to o l ho l d er w i t h 1 0 7 .5 ° ap p roa c h a n gl e , f or p os i t i v e 55° r h om b i c i n s e r t s

b
f
107.5°

L2 L1
107.5°

h1

h
Cutting edge style Q Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

SDQCR/L2020K11 20 20 125 20.5 20 25 0.8 DC**11T3...
SDQCR2525M11 25 25 150 21.5 25 32 0.8 DC**11T3...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SDQCR/L... CSTB-3.5L DTS5-3.5 SSD32 P-3.5 T-15F

S VQC R /L
S c re w -o n c l a m p to o l ho l d er w i t h 1 1 7 .5 ° ap p roa c h a n gl e , f or p os i t i v e 35° r h om b i c i n s e r t s

b
117.5°
f

L2 L1
117.5°
h1

h
Cutting edge style Q Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert

SVQCR/L163 1.00 1.00 6.00 1.50 1.00 1.25 0.031 VC**33...

Metric h b L1 L2 h1 f rε** Insert

SVQCR/L2020K16 20 20 125 35 20 27 0.8 VC**1604...
SVQCR/L2525M16 25 25 150 35 25 32 0.8 VC**1604...
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SVQCR/L... CSTB-3.5L DTS5-3.5 SSV32 P-3.5 T-15F

Reference pages
SDQCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179
SVQCR/L: Inserts → B149 -, CBN → B171 -, PCD → B179 -

Tungaloy B267
Ext. Toolholder SV H C R /L
Sc re w -o n c l a mp to o l ho l d er w i t h 1 0 7 .5 ° ap p roa c h a n gl e , f or p os i t i v e 35° r h om b i c i n s e r t s

b
f
50°
L2 L1
107.5°

h1

h
Cutting edge style H Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert

SVHCR/L2525M22 25 25 150 33.8 25 32 0.8 VCG*2205...

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Shim screw Shim Wrench 1 Wrench 2
SVHCR/L2525M22 CSTB-4.5L110P DTS6-4.5 SSV42 P-4.5 T-15F

TR AC N
Ta p e r-l o c k to ol ho l d er w i t h 9 1 ° ap p ro ach a n gl e , f or R T t y p e t a p e re d rou n d i n s e r t s

b
f

L2
L1
h1

h
Cutting edge style A
Metric h b L1 L2 h1 f Insert
TRACN2020K05 20 20 125 20 20 20.3 RT05
TRACN2020K06 20 20 125 22 20 20.4 RT06
TRACN2525M05 25 25 150 20 25 25.3 RT05
TRACN2525M06 25 25 150 22 25 25.4 RT06
TRACN2525M08 25 25 150 25 25 25.5 RT08

TR D C N
Ta p e r-l o c k to ol ho l d er w i t h 4 5 ° ap p ro ach a n gl e , f or R T t y p e t a p e re d rou n d i n s e r t s
b
f

L2
L1
h1

Cutting edge style D

Metric h b L1 L2 h1 f Insert
TRDCN2020K05 20 20 125 20 20 12.5 RT05
TRDCN2525M05 25 25 150 20 25 15 RT05
TRDCN2525M06 25 25 150 22 25 15.5 RT06

Reference pages
SVHCR/L: Inserts → B150
TRACN, TRDCN: Inserts → B127

B268 www.tungaloyamerica.com
S R G C R /L

Ext. Toolholder
S c re w - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s

b
f
L2
30° L1

h1

h
Cutting edge style G Right hand (R) shown.

Inch h b L1 L2 h1 f Insert Torque*

SRGCR/L164-6F  1.00 1.00 6.00 0.69 1.00 1.25 RCMT1204M0-6RS/-6RM 2.21

Metric h b L1 L2 h1 f Insert Torque*

SRGCR/L2525M12-6F 25 25 150 18.6 25 32 RCMT1204M0-6RS/-6RM 3
*Torque: Recommended torque (lbf·ft, N∙m) for clamping

SPARE PARTS
Designation Clamping screw Lubricant Wrench
SRGCR/L164-6F,
CSTB-4 M-1000 T-15F
SRGCR/L2525M12-6F

SRDCN
S c re w - o n to o l h o l d e r w i t h 4 5 ° a p p ro a c h a n g l e , f o r p o s i t i v e ro u n d i n s e r t s
f

b
L2
L1
h1

Cutting edge style D

Inch h b L1 L2 h1 f Insert Torque*
SRDCN164-6F  1.00 1.00 6.00 0.95 1.00 0.74 RCMT1204M0-6RS/-6RM 2.21

Metric h b L1 L2 h1 f Insert Torque*

SRDCN2525M12-6F 25 25 150 24.1 25 18.5 RCMT1204M0-6RS/-6RM 3

*Torque: Recommended torque (lbf·ft, N∙m) for clamping

SPARE PARTS
Designation Clamping screw Lubricant Wrench
SRDCN164-6F ,
CSTB-4 M-1000 T-15F
SRDCN2525M12-6F

Reference pages
SRGCR/L, SRDCN: Inserts → B270, Standard cutting conditions → B270

Tungaloy B269
 INSERT
Ext. Toolholder RCMT

6RS 6RM

Coated Cermet ød s ød1

Designation
T9115 T9125 NS9530 (in) (in) (in)
RCMT1204M0-6RS 䖃 䖃 䖃 0.472 0.187 0.203

RCMT1204M0-6RM 䖃 䖃 䖃 0.472 0.187 0.203

䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S

Chip- Cutting speed Depth of cut Feed

ISO Workpiece material breaker Grade
Vc (sfm) ap (in) f (ipr)

6RS T9115 492 - 984 0.020 - 0.079 0.020 - 0.039

6RS T9125 394 - 820 0.020 - 0.079 0.020 - 0.039

6RS NS9530 492 - 820 0.020 - 0.079 0.020 - 0.039

Steels
1045, etc.
6RM T9115 492 - 984 0.039 - 0.118 0.020 - 0.039

6RM T9125 394 - 820 0.039 - 0.118 0.020 - 0.039

6RM NS9530 492 - 820 0.039 - 0.118 0.020 - 0.039

B270 www.tungaloyamerica.com
CC LN R /L-R D

Ext. Toolholder
D o u b l e c l a m p too l ho l d er f o r ceram i c i nser t w i t h d i m p l e , 95° a p p roa c h a n gl e , f or n e ga t i v e 80° r h om bic
inserts

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

CCLNR/L16M45-RD 1.000 1.000 6.000 1.300 1.000 1.250 0.910 0.047 CNGD45... 3.0

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CCLNR/L**-RD CCP4-A CCS4-A CC44-A BH5-10-A BP-5-A P-3 P-4

CD JN R /L-R D
D o u b l e c l a m p too l ho l d er f o r ceram i c i nser t w i t h d i m p l e , 93° a p p roa c h a n gl e , f or n e ga t i v e 55° r h om bic
inserts

b
f

L2 L1
30°

93°
h1

Cutting edge style J Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

CDJNR/L16M45-RD 1.000 1.000 6.000 1.500 1.000 1.250 0.047 DNGD45... 3.0
*Torque: Recommended torque (lbf·ft) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CDJNR/L**-RD CCP4-A CCS4-A CD44-A BH5-10-A BP-5-A P-3 P-4

Reference pages
CCLNR/L-RD: Inserts → B062, Standard cutting conditions → B274
CDJNR/L-RD: Inserts → B071, Standard cutting conditions → B274

Tungaloy B271
Ext. Toolholder C D N N N -R D
Do u b l e c l a m p to o l ho l d er f o r ceram i c i nser t w i t h d i m p l e , 63° a p p roa c h a n gl e , f or n e ga t i v e 55° r h o mbic
inserts

b
f
L2 L1
63°

h1

h
Cutting edge style N
Inch h b L1 L2 h1 f rε** Insert Torque*
CDNNN16M45-RD 1.000 1.000 6.000 1.580 1.000 0.500 0.047 DNGD45... 3.0

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CDNNN16M45-RD CCP4-A CCS4-A CD44-A BH5-10-A BP-5-A P-3 P-4

C V VN N -R D
Do u b l e c l a m p to o l ho l d er f o r ceram i c i nser t w i t h d i m p l e , 72. 5° a p p roa c h a n gl e , f or n e ga t i v e 35° r ho mbic
inserts

b
f

L2 L1
72.5°
h1

Cutting edge style V

Inch h b L1 L2 h1 f rε** Insert Torque*
CVVNN16M35-RD 1.000 1.000 6.000 1.810 1.000 0.500 0.047 VNGD35... 3.0

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CVVNN16M35-RD CCP4-A CCS4-A CV34-A BH-4-10-A BP-5-A P-3 P-4

Reference pages
CDNNN-RD: Inserts → B071, Standard cutting conditions → B274
CVVNN-RD: Inserts → B096, Standard cutting conditions → B274

B272 www.tungaloyamerica.com
CS S N R /L-R D

Ext. Toolholder
D o u b l e c l a m p to o l h o l d e r f o r c e ra m i c i n s e r t w i t h d i m p l e , 4 5 ° a p p ro a c h a n g l e , f o r n e g a t i v e s q u a re i n s e r t s

45°

b
f
L2
L1
45°

h1

h
Cutting edge style S Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

CSSNR/L16M45-RD 1.000 1.000 6.000 1.260 1.000 1.250 0.047 SNGD45... 3.0

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CSSNR/L16M45-RD CCP4-A CCS4-A CS44-A BH5-10-A BP-5-A P-3 P-4

CH S N R -R D
D o u b l e c l a m p too l ho l d er f o r ceram i c i nser t w i t h d i m p l e , 45° a p p roa c h a n gl e , f or n e ga t i v e h ex a gon a l in-
serts

45°

b
f

L2
L1
45°
h1

Cutting edge style S Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

CHSNR16M45-RD 1.000 1.000 6.000 1.260 1.000 1.250 0.047 HNGD45... 3.0
*Torque: Recommended torque (lbf·ft) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Shim Shim screw Spring Wrench 1 Wrench 2
CHSNR16M45-RD CCP4-A CCS4-A CH44-A BH-40050-A BP-5-A P-3 P-4

Reference pages
CSSNR/L-RD: Inserts → B081, Standard cutting conditions → B274
CHSNR-RD: Inserts → B105, Standard cutting conditions → B274

Tungaloy B273
Ext. Toolholder Par ts f o r C- t y p e

Toolholders Designation Applicable Insert Designation Clamp Clamp screw Shim Shim screw Spring Wrench

CCLNR16M45-RD
CNGD45 CC44-A
CCLNL16M45-RD

CDJNR16M45-RD

CDJNL16M45-RD DNGD45 BH5-10-A CD44-A

CDNNN16M45-RD
P4,
CSSNR16M45-RD CCP4-A CCS4-A BP-5-A
P3
SNGD45 CS44-A
CSSNL16M45-RD

CVVNN16M35-RD VNGD35 BH-4-10-A CV34-A

CHSNR16M45-RD HNGD45 BH-40050-A CH44-A

STAN DARD CUT T ING CONDIT IO N S

Cutting speed Depth of cut Feed

ISO Workpiece material Grade
Vc (sfm) ap (in) f (ipr)

Grey cast irons FX105 2300 (1000 - 3300) 0.040 (0.002 - 0.120) 0.012 (0.002 - 0.024)

Ductile cast irons FX105 650 (330 - 1000) 0.040 (0.002 - 0.120) 0.008 (0.002 - 0.016)

B274 www.tungaloyamerica.com
X W X PR /L

Ext. Toolholder
D o u b l e c l a m p i n g to o l ho l d er w i t h 2 0 ° ap p ro ac h a n gl e f or rou gh i n g op e ra t i on w i t h p os i t i v e t r i gon i n s e r ts

b
f
20° L1

h
Cutting edge style X Right hand (R) shown.

Inch h b L1 f Insert
XWXPR/L16-09 1.000 1.000 6.000 1.250 WPMT090725ZPR/L-ML
XWXPR/L20-09 1.250 1.250 7.000 1.500 WPMT090725ZPR/L-ML
XWXPR/L24-09 1.500 1.500 7.000 2.000 WPMT090725ZPR/L-ML

Note: Care should be taken not to confuse the hand of inserts to be used.

SPARE PARTS
Designation Clamp set Clamping screw Wrench
XWXPR/L... CSY-20 CSPB-5 IP-20T

INSERT C : Continuous cutting

W P M T09-M L L : Light interrupted cutting
H : Heavy interrupted cutting
P Steel CL LH CL
Trigon, 80° M Stainless CL
with hole
K Cast iron CL CL
N Non-ferrous
Positive 11° S Superalloys CL
H Hard materials
Coated
Application

Corner
radius

Chipbreaker Designation
AH120
T9125
T9115

ML WPMT090725ZPR-ML 0.098 䖃 䖃 䖃
Heavy

WPMT090725ZPL-ML 0.098 䖃 䖃 䖃

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS

ISO Workpiece material Cutting speed: Depth of cut: Feed:

Grade Chipbreaker Vc (sfm) ap (in) f (ipr)
Mild and low carbon steels
T9125 ML 500 (330 - 830) 0.060 (0.020 - 0.100) 0.060 (0.020 - 0.100)
400SS, 1025, etc. < 180 HB

Carbon and alloy steels

T9115 ML 500 (330 - 830) 0.060 (0.020 - 0.100) 0.060 (0.020 - 0.100)
1049, 4142, etc. < 300HB

Stainless steels
T9125 ML 500 (330 - 830) 0.060 (0.020 - 0.100) 0.060 (0.020 - 0.100)
304, 316, etc. < 250 HB

Gray and ductile cast irons

AH120 ML 500 (330 - 830) 0.060 (0.020 - 0.100) 0.060 (0.020 - 0.100)
No35B, 60-40-18, etc.

Note: When the side cutting edge is used for facing, the maximum feed is limited to within 0.039 ipr.

Tungaloy B275
 TLAN R /L
Ext. Toolholder
Sc re w -o n c l a mp to o l ho l d er f o r ro ug hi ng o p e ra t i on w i t h 93° a p p roa c h a n gl e , f or n e ga t i v e t a n ge n tial inser ts

b
f
L2
L1
93° 1616-type
1616形

h1

h
Cutting edge style A Right hand (R) shown.

Inch h b L1 L2 h1 f Insert
TLANR/L10-12 0.625 0.625 4.000 0.790 0.625 0.750 LNMX1204**R/L...
TLANR/L12-12 0.750 0.750 4.500 0.790 0.750 1.000 LNMX1204**R/L...
TLANR/L12-16 0.750 0.750 4.500 1.000 0.750 1.000 LNMX1606**R/L...
TLANR/L16-12 1.000 1.000 6.000 0.790 1.000 1.250 LNMX1204**R/L...
TLANR/L16-16 1.000 1.000 6.000 1.000 1.000 1.180 LNMX1606**R/L...
TLANR/L20-16 1.250 1.250 6.000 1.380 1.250 1.460 LNMX1606**R/L...
TLANR/L20-24 1.250 1.250 6.000 1.380 1.250 1.500 LNMX2410**R/L...
TLANR/L24-16 1.500 1.500 7.000 1.380 1.500 1.700 LNMX1606**R/L...
TLANR/L24-24 1.500 1.500 7.000 1.380 1.500 1.700 LNMX2410**R/L...
TLANR/L32-24 2.000 2.000 8.000 1.380 2.000 2.275 LNMX2410**R/L...

SPARE PARTS
Designation Clamping screw Shim screw Shim Spring Wrench 1 Wrench 2
TLANR**-12 CSTB-3.5L115-S CSTF-2L055-S TSL12R - KEYV-T10 T-6F-S
TLANL**-12 CSTB-3.5L115-S CSTF-2L055-S TSL12L - KEYV-T10 T-6F-S
TLANR**-16 CSTB-4L115-S - TSL16R PSP-16 KEYV-T15 -
TLANL**-16 CSTB-4L115-S - TSL16L PSP-16 KEYV-T15 -
TLANR**-24 CSTB-5L163-S - TSL24R PSP-16 KEYV-T20 -
TLANL**-24 CSTB-5L163-S - TSL24L PSP-16 KEYV-T20 -

Reference pages
TLANR/L: Inserts → B278, Standard cutting conditions → B279

B276 www.tungaloyamerica.com
T LB N R /L

Ext. Toolholder
S c re w -o n c l a m p to o l ho l d er f o r ro ug hi ng o p e ra t i on w i t h 75° a p p roa c h a n gl e , f or n e ga t i v e t a n ge n t i a l inser ts

b
f
L2
L1
75°

h1

h
Cutting edge style B Right hand (R) shown.

Inch h b L1 L2 h1 f Insert
TLBNR/L24-24 1.500 1.500 8.000 1.380 1.500 1.380 LNMX2410**R/L...

SPARE PARTS
Designation Clamping screw Shim Spring pin Wrench
TLBNR24-24 CSTB-5L163-S TSL24R PSP-16 KEYV-T20
TLBNL24-24 CSTB-5L163-S TSL24L PSP-16 KEYV-T20

T LFN R /L
S c re w -o n c l a m p to o l ho l d er f o r ro ug hi ng o p e ra t i on w i t h 93° a p p roa c h a n gl e , f or n e ga t i v e t a n ge n t i a l inser ts

93°

b
f

L2
L1
93°
h1

h
Cutting edge style F Right hand (R) shown.

Inch h b L1 L2 h1 f Insert
TLFNR/L16-16 1.000 1.000 6.000 0.780 1.000 1.000 LNMX1606**L/R...
TLFNR/L20-16 1.250 1.300 6.000 0.780 1.250 1.000 LNMX1606**L/R...

Note: The right hand insert (R) is used for the left hand toolholders (TLFNL** type), and the left hand insert (L) is used for the right hand toolholders (TLFNR** type).

SPARE PARTS
Designation Clamping screw Shim Spring pin Wrench
TLFNR16-16 CSTB-4L115-S TSL16L PSP-16 KEYV-T15
TLFNL16-16 CSTB-4L115-S TSL16R PSP-16 KEYV-T15
TLFNR20-16 CSTB-4L115-S TSL16L PSP-16 KEYV-T15
TLFNL20-16 CSTB-4L115-S TSL16R PSP-16 KEYV-T15

Reference pages
TLBNR/L, TLFNR/L: Inserts → B278, Standard cutting conditions → B279

Tungaloy B277
Ext. Toolholder S-TLA N R /L
Sc re w -o n c l a mp to o l ho l d er f o r ro ug hi ng o p e ra t i on w i t h 91° a p p roa c h a n gl e , f or n e ga t i v e t a n ge n tial inser ts

øDm

øDs
91°

f
L2 h
L1

h1
Cutting edge style A Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h h1 Insert

S16-TLANR/L12-D34 Steel 2.090 1.000 0.670 12.000 1.500 0.920 0.460 LNMX1204**L/R...
S20-TLANR/L12-D34 Steel 2.090 1.250 0.870 14.000 1.750 1.140 0.570 LNMX1204**L/R...
S24-TLANR/L12-D34 Steel 2.090 1.500 1.060 16.000 2.000 1.340 0.670 LNMX1204**L/R...
S32-TLANR/L16-D54 Steel 3.350 2.000 1.460 16.000 2.360 1.810 0.905 LNMX1606**L/R...

Note: The right hand insert (R) is used for the left hand toolholders (TLANL** type), and the left hand insert (L) is used for the right hand toolholders (TLANR** type).

SPARE PARTS
Designation Clamping screw Shim screw Shim Spring pin Wrench 1 Wrench 2
S**-TLANR/L12-D34 CSTB-3.5L115-S CSTF-2L055-S TSL12L/RI - KEYV-T10 T-6F-S
S32-TLANR16-D54 CSTB-4L115-S - TSL16LI PSP-16 KEYV-T15 -
S32-TLANL16-D54 CSTB-4L115-S - TSL16RI PSP-16 KEYV-T15 -

INSERT
L N M X 1 2 / 1 6 /24
L rε
W

Coated
Designation rε T9115 T9125 AH725 W L h
R L R L R L
LNMX120408R/L-TDR 0.031 䖃 䖃 䖃 䖃 0.189 0.473 0.457

LNMX120412R/L-TDR 0.047 䖃 䖃 䖃 䖃 0.189 0.473 0.457

LNMX160608R/L-TDR 0.031 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX160612R/L-TDR 0.047 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX160616R/L-TDR 0.063 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX241016R/L-TDR 0.063 䖃 䖃 䖃 䖃 0.370 0.945 0.807

LNMX241024R/L-TDR 0.094 䖃 䖃 䖃 䖃 0.370 0.945 0.807

LNMX160608R/L-MDR 0.031 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX160612R/L-MDR 0.047 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX160608R/L-TWR 0.031 䖃 䖃 䖃 䖃 0.252 0.638 0.532

LNMX160612R/L-TWR 0.047 䖃 䖃 䖃 䖃 0.252 0.638 0.532

䖃 : Line up

Reference pages
Standard cutting conditions → B279

B278 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
L N M X 1204 * Values in red shows the condition for facing

Ext. Toolholder
Chip- Cutting speed Depth of cut: ap (in) Feed: f (ipr)
ISO Workpiece material Grade
breaker Vc (sfm) rε : 0.031 rε : 0.047 rε : 0.031 rε : 0.047
0.020 - 0.195 0.031 - 0.195
TDR T9115 390 - 820 0.006 - 0.024 0.010 - .031
0.020 - 0.086 0.031 - 0.086
Steels
1045, 4130, etc.
0.020 - 0.195 0.031 - 0.195
TDR T9125 260 - 590 0.006 - 0.024 0.010 - .031
0.020 - 0.086 0.031 - 0.086

0.020 - 0.195 0.031 - 0.195

TDR T9115 330 - 590 0.006 - 0.024 0.010 - .031
0.020 - .086 0.031 - 0.086
Stainless steels
304, 316, etc.
0.020 - 0.195 0.031 - 0.195
TDR T9125 260 - 590 0.006 - 0.024 0.010 - .031
0.020 - 0.086 0.031 - 0.086

L N M X 1606
Chip- Cutting speed Depth of cut: ap (in) Feed: f (ipr)
ISO Workpiece material Grade
breaker Vc (sfm) rε : 0.031 rε : 0.047 rε : 0.063 rε : 0.031 rε :0 .047 rε : 0.063
0.020 - 0.197 0.031 - 0.236 0.039 - 0.315
TDR T9115 390 - 820 0.006 - 0.024 0.010 - 0.031 0.012 - 0.039
0.020 - .126 .031 - .126 0.039 - 0.126

0.020 - 0.197 0.031 - 0.236 0.039 - 0.315

TDR T9125 260 - 590 0.006 - 0.024 0.010 - 0.031 0.012 - 0.039
Steels 0.020 - .126 .031 - .126 0.039 - 0.126
1045, 4130, etc. 0.020 - 0.197 0.031 - 0.236
TWR T9115 390 - 820 - 0.006 - 0.024 0.010 - 0.031 -
0.020 - 0.126 0.031 - 0.126

0.020 - 0.197 0.031 - 0.236

TWR T9125 260 - 590 - 0.006 - 0.024 0.010 - 0.031 -
0.020 - 0.126 0.031 - 0.126

0.020 - 0.197 0.031 - 0.236 0.039 - 0.315

TDR T9115 330 - 590 0.006 - 0.024 0.010 - 0.031 0.012 - 0.039
0.020 - 0.126 0.031 - 0.126 0.039 - 0.126

0.020 - 0.197 0.031 - 0.236 0.039 - 0.315

TDR T9125 260 - 590 0.006 - 0.024 0.010 - 0.031 0.012 - 0.039
0.020 - 0.126 0.031 - 0.126 0.039 - 0.126

0.059 - 0.236 0.059 - 0.276

MDR T9115 330 - 490 - 0.004 - 0.020 0.006 - 0.028 -
Stainless steels 0.020 - 0.126 0.031 - 0.126
304, 316, etc. 0.059 - 0.236 0.059 - 0.276
MDR AH725 160 - 490 - 0.004 - 0.020 0.006 - 0.028 -
0.020 - 0.126 0.031 - 0.126

0.020 - 0.197 0.031 - 0.236

TWR T9115 330 - 590 - 0.006 - 0.024 0.010 - 0.031 -
0.020 - 0.126 0.031 - 0.126

0.020 - 0.197 0.031 - 0.236

TWR T9125 260 - 590 - 0.006 - 0.024 0.010 - 0.031 -
0.020 - 0.126 0.031 - 0.126

L N M X 2410
Chip- Cutting speed Depth of cut: ap (in) Feed: f (ipr)
ISO Workpiece material Grade
breaker Vc (sfm) rε : 0.063 rε : 0.094 rε : 0.063 rε : 0.094

0.156 - 0.585 0.195 - 0.585

TDR T9115 390 - 820 0.012 - 0.039 0.012 - 0.043
0.039 - 0.176 0.039 - 0.176
Steels
1045, 4130, etc.
0.156 - 0.585 0.195 - 0.585
TDR T9125 260 - 490 0.012 - 0.039 0.012 - 0.043
0.039 - 0.176 0.039 - 0.176

0.156 - 0.585 0.195 - 0.585

TDR T9115 330 - 590 0.012 - 0.039 0.012 - 0.043
0.039 - 0.176 0.039 - 0.176
Stainless steels
304, 316, etc.
0.156 - 0.585 0.195 - 0.585
TDR T9125 260 - 490 0.012 - 0.039 0.012 - 0.043
0.039 - 0.176 0.039 - 0.176

Tungaloy B279
Tur nLine - Inte r na l Toolholde r
Inch Metric

B2 8 8
Economical double-sided inserts with excellent sharpness
Shank ø0.375 - 1.000"

B2 9 4
Small-sized “Eco” insert series for maximized profits
Shank ø1.000 - 1.250" (ø16 - 32 mm)

B2 9 9
Highly rigid toolholders providing good chip evacuation

Shank ø0.157 - 1.000" (ø4 - 50 mm)

B 32 6
Highly rigid clamping system with excellent repeatability

Shank ø1.000 - 2.000"

B 32 9
Inserts with 25° corner angle for profiling
Shank ø0.500 - 0.625" (ø12 - 16 mm)

ISO-Turn Internal B330

Toolholders for general internal turning

B280 www.tungaloyamerica.com
M i n i Fo rc e -Tu r n

Tungaloy B281
 Inter na l Toolholder - Q uick Guide
Positive type

ISO Insert
Inch
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r ( i n)

Y-Pro
Style Description & Application Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SEXPR/L ø0.157 -
Steel ø0.313 ø0.250
Boring & internal facing 䘟 B302
Insert type: EP †† Carbide ø0.157 - ø0.250
ø0.313
SCLCR/L ø0.375 -
Steel ø1.000 ø0.500 ø1.280 B299
Boring & internal facing 䘟
Int. Toolholder

Carbide ø0.375 - ø0.500 ø1.250

B301
Insert type: CC †† ø1.000
STUPR/L ø0.313 -
Steel ø1.000 ø0.438 ø1.250
Boring 䘟 B310
Insert type: TP †† Carbide ø0.313 - ø0.438 ø0.875
ø0.625
STFPR/L
Blind hole boring 䘟 Carbide ø0.375 - ø0.500 ø1.000 B309
Insert type: TP †† ø0.750

SCLPR/L ø0.375 -
Steel ø0.625 ø0.500 ø0.875
Boring & internal facing 䘟 B303
Insert type: CP †† Carbide ø0.375 - ø0.500 ø0.875
ø0.625
STFCR/L
Blind hole boring 䘟 Carbide ø0.375 - ø0.430 ø0.930 B308
Insert type: TC †† ø0.750

SDUCR/L ø0.375 -
Steel ø0.750 ø0.625 ø1.000
á Boring & internal profiling 䘟 B313
Insert type: DC †† Carbide ø0.375 - ø0.625 ø1.000
ø0.750
SVUCR/L
á
Boring & internal profiling 䘟 Steel ø0.625 - ø0.875 ø1.000 B315
Insert type: VC †† ø0.750

SVUBR/L
á
Boring & internal profiling 䘟 Steel ø0.750 ø1.000 B314
Insert type: VB ††

SDQCR/L
á Boring & internal profiling 䘟 Steel
ø0.375 -
ø0.625 ø0.875 B316
Insert type: DC †† ø0.625

SVQCR/L
Boring & internal profiling ø0.500 -
á 䘟 Steel ø0.625 ø0.688 ø1.000 B318
Insert type: VC ††

SVQBR/L
á Boring & internal profiling 䘟 Steel ø0.625 ø1.000 B317
Insert type: VB ††

B282 www.tungaloyamerica.com
 ISO Insert
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r ( i n)

Y-Pro
Style Description & Application Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SDZCR/L
á Internal retracting 䘟 Steel ø0.625 ø0.875 B319
Insert type: DC ††

SVZCR/L
Internal retracting ø0.500 -
䘟 Steel ø0.750 ø1.000 B320

Int. Toolholder
á
Insert type: VC †† ø0.750

SVZBR/L
Internal retracting 䘟 B320
á Steel ø0.750 ø1.000
Insert type: VB ††

SVJCR/L
Internal sphere cutting 䘟 Steel ø0.625 ø1.000 B306
Insert type: VC ††

SVJBR/L
Internal sphere cutting 䘟 Steel ø0.625 ø1.000 B306
Insert type: VB ††

SYQBR/L ø0.500 -
Steel ø0.625 ø0.750 ø0.875
á Internal undercut & profiling 䘟 B329
Insert type: YW †† Carbide ø0.500 - ø0.750 ø0.875
ø0.625
SYUBR/L Steel ø1.000
á ø0.625
Boring & internal profiling 䘟 B329
Insert type: YW †† Carbide ø0.500 - ø0.875 ø1.000
ø0.625

Tungaloy B283
 Inter na l Toolholder - Q uick Guide
Positive type

ISO Insert
Metric
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r (m m)

Y-Pro
Style Description & Application Ty p e Ø See
0 10 20 30 40 50 page
SEXPR/L
Steel ø4 - ø8 ø4.5 ø7 B302
Boring & internal facing 䘟 B305
Insert type: EP †† Carbide ø4 - ø8 ø4.5 ø7

Steel ø4 - ø25 ø5 ø27

SCLCR/L
Int. Toolholder

䘟 B300
Boring & internal facing Carbide ø4 - ø25 ø5 ø27
B330
Insert type: CC ††
Reinforced ø12 - ø25 ø16 ø32

SWUBR/L Steel ø5 - ø8 ø6 ø8
Boring 䘟 B312
Insert type: WB †† Carbide ø5 - ø8 ø6 ø8

Steel ø7 - ø32 ø8 ø34

STUPR/L
Boring 䘟 Carbide ø7 - ø25
B311
ø8 ø27
B331
Insert type: TP ††
Reinforced ø12 - ø25 ø14 ø31

STFPR/L Steel ø8 - ø25 ø10 ø27

Blind hole boring 䘟 B309
Insert type: TP †† Carbide ø8 - ø20 ø10 ø22

Steel ø8 - ø25 ø10 ø27

SCLPR/L
䘟 B304
Boring & internal facing Carbide ø8 - ø16 ø10 ø20
B330
Insert type: CP ††
Reinforced ø12 - ø25 ø14 ø32

STFCR/L Steel ø10 - ø16 ø12 ø18

Blind hole boring 䘟 B308
Insert type: TC †† Carbide ø10 - ø16 ø12 ø18

SSKPR
Through boring 䘟 Steel ø16 - ø25 ø20 ø31 B307
Insert type: SP ††

SDUCR/L Steel ø10 - ø25 ø13 ø32

á Boring & internal profiling 䘟 Carbide ø10 - ø20
B313
Insert type: DC †† ø13 ø27

Steel ø12 - ø25 ø16 ø32

á SVUCR/L
Boring & internal profiling 䘟 Carbide ø12 - ø25 ø18 ø32 B322
Insert type: VC †† Reinforced ø25 ø32

Steel ø16 - ø25 ø20 ø32

á SVUBR/L
Boring & internal profiling 䘟 Carbide ø16 - ø25 ø24.5 ø34 B332
Insert type: VB †† Reinforced ø20 ø25

Steel ø10 - ø25 ø13 ø30

SDQCR/L
á Boring & internal profiling 䘟 Carbide ø10 - ø20 B316
ø13 ø25 B333
Insert type: DC ††
Reinforced ø16 - ø25 ø20 ø32

Steel ø10 - ø16 ø13.5 ø21.5

SVQCR/L
á 䘟 Carbide ø10 - ø16
B318
Boring & internal profiling ø13.5 ø21.5 B334
Insert type: VC †† Reinforced ø25 ø32

Steel ø12 - ø25 ø17 ø30.5

SVQBR/L
á Boring & internal profiling 䘟 Carbide ø12 - ø25 ø17 ø30.5 B334
Insert type: VB ††
Reinforced ø20 ø25

B284 www.tungaloyamerica.com
 ISO Insert
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r (m m)

Y-Pro
Style Description & Application Ty p e Ø See
0 10 20 30 40 50 page
SDZCR/L Steel ø12 - ø25 ø14 ø25
á Internal retracting 䘟 B319
Insert type: DC †† Carbide ø12 - ø16 ø18 ø22

SVZCR/L
Internal retracting
䘟 Steel ø12 ø16 B320

Int. Toolholder
á
Insert type: VC ††

SVZBR/L
Internal retracting 䘟 Steel ø16 - ø32 ø20 ø40 B320
á
Insert type: VB ††

SEZPR/L Steel ø4 - ø5 ø5.5 ø6.5

Internal retracting 䘟 B321
Insert type: EP †† Carbide ø4 - ø5 ø5.5 ø6.5

SVJCR/L
Internal sphere cutting 䘟 Steel ø12 - ø16 ø16 ø20 B306
Insert type: VC ††

SVJBR/L
Internal sphere cutting 䘟 Steel ø20 - ø25 ø25 ø30 B306
Insert type: VB ††

SYQBR/L Steel ø12 - ø16 ø17 ø21.5

á Internal undercut & profiling 䘟 B329
Insert type: YW †† Carbide ø12 - ø16 ø17 ø21.5

SYUBR/L Steel ø16 ø20

á
Boring & internal profiling 䘟 B329
Insert type: YW †† Carbide ø12 - ø16 ø20 ø24.5

Clamp-on
Metric
Shank Shank
insert

M i n . b o r e d i a m e t e r (m m)
See
ISO

Style Description & Aplication Ty p e Ø

0 10 20 30 40 50 page
CTFPR/L
Steel ø12 - ø32 ø16 ø40
Blind hole boring 䘟 B335
Insert type: TP †† (Without hole) Carbide ø12 - ø16 ø16 ø20

CSKPR/L
Through boring 䘟 Steel ø16 - ø25 ø20 ø32 B335
Insert type: SP †† (Without hole)

Tungaloy B285
 Inter na l Toolholder - Q uick Guide
MiniForce-Turn - Double-sided insert with positive cutting edges

MiniForce
Inch
MiniForce-Turn Shank Shank

-Tu r n
M i n . b o r e d i a m e t e r ( i n)
Style Description & Application Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SWLXR/L ø0.375 -
Steel ø1.000 ø0.500 ø1.250
Boring & facing 䘟 B288
Insert type: WXGU Carbide ø0.375 - ø0.500 ø1.250
ø1.000
SDXXR/L ø0.375 -
Int. Toolholder

á Steel ø1.000 ø0.625 ø1.250

Internal profiling 䘟 B288
Insert type: DXGU Carbide ø0.375 - ø0.625 ø1.250
ø1.000
SDZXR/L
Internal retracting 䘟 Steel ø0.500 -
ø0.625 ø0.875 B289
á
Insert type: DXGU ø0.750

Negative type
Double-clamp
ISO-EcoTurn
ISO insert

Inch
Turning A Shank Shank M i n . b o r e d i a m e t e r ( i n)
Ty p e Ø See
Style Description & Application
0.750 1.125 1.500 2.000 2.500 3.000 page
ATFNR/L
Boring ø1.000-
䘟 Steel ø1.250 ø1.250 ø1.560 B327
Insert type: TN ††

ASKNR/L
ø1.000-
Boring 䘟 Steel ø1.250 ø1.250 ø1.560 B327
Insert type: SN ††

ADUNR/L
Boring & internal profiling ø1.000- B296
β 䘟 䘟 Steel ø1.500 ø1.250 ø2.000
B328
Insert type: DN ††

ACLNR/L
Boring & internal facing ø1.000- B294
䘟 䘟 Steel ø2.000 ø1.250 ø2.500
B326
Insert type: CN ††, GN ††

AWLNR/L
ø1.000- B295
Boring & internal facing 䘟 䘟 Steel ø2.000 ø1.250 ø2.500
B326
Insert type: WN ††

AVUNR/L
Boring & internal profiling ø1.250-
25° 䘟 Steel ø1.500 ø1.560 ø2.000 B328
Insert type: VN ††

Lever-lock
ISO-EcoTurn

Inch
ISO insert

StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r ( i n)

See
Style Description & Application Ty p e Ø
0.750 1.125 1.500 2.000 2.500 3.000 page
PVUNR/L
á ø1.250-
Boring & internal profiling 䘟 䘟 Steel ø1.650
ø1.000 ø1.250 B298
Insert type: VN ††

B286 www.tungaloyamerica.com
Lever-lock

ISO-EcoTurn
Metric

ISO insert
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r (m m)
Style Description & Application Ty p e Ø See
20 30 40 50 60 70 page
PTUNR/L B297
Boring Steel ø16 - ø32 ø20 ø40 B324
䘟 䘟 B339
Insert type: TN †† Reinforced ø16 - ø50 ø20 ø63
B340
PTFNR/L B296

Int. Toolholder
Boring 䘟 䘟 Steel ø25 - ø50 ø32 ø63 B323
Insert type: TN †† B338

PSKNR/L
Through boring B322
䘟 Steel ø32 - ø50 ø40 ø63
B337
Insert type: SN ††

B297
PDUNR/L B324
Internal profiling Steel ø20 - ø50 ø25 ø63
䘟 䘟 B338
Insert type: DN †† Reinforced ø32 - ø50 ø40 ø63 B339
B347
PCLNR/L B294
Steel ø16 - ø50 ø20 ø63 B321
Boring & internal facing 䘟 䘟 B336
Insert type: CN ††, GN †† Reinforced ø16 - ø50 ø20 ø63
B347
PWLNR/L B295
Boring & facing 䘟 䘟 Steel ø16 - ø40 ø20 ø50 B322
Insert type: WN †† B337
PVUNR/L
á
B298
Boring & internal profiling 䘟 䘟 Steel ø25 - ø40 ø32 ø50
B325
Insert type: VN ††

PDZNR/L
B325
Internal retracting 䘟 Steel ø32 - ø50 ø40 ø63
B340
Insert type: DN ††

Multi-clamp
Metric
Shank Shank
insert

M i n . b o r e d i a m e t e r (m m) See
ISO

Style Description & Application Ty p e Ø page

20 30 40 50 60 70
MTFNR/L
Boring 䘟 Steel ø25 ø32 B342
Insert type: TN ††

MSKNR/L
Through boring 䘟 Steel ø25 ø32 B342
Insert type: SN ††

MDUNR/L
Boring & internal profiling 䘟 Steel ø25 ø32 B343
Insert type: DN ††

MCLNR/L
Boring & internal facing 䘟 Steel ø25 ø32 B341
Insert type: CN ††, GN ††

MWLNR/L
Boring & internal facing 䘟 Steel ø25 - ø50 ø32 ø70 B341
Insert type: WN ††

Tungaloy B287
 A/E-S W LX R /L
Fo r t r i g o n i n s e r t w i t h 6 e d g e s

øDm h

f
95°
α° L2

øDs
L1

θ°
Int. Toolholder

Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A06-SWLXR/L2-D08 STEEL 0.500 0.375 0.281 5.000 0.750 0.350 -10 -14 0.016 WXGU22**L/R... 0.66
A08-SWLXR/L2-D11 STEEL 0.688 0.500 0.406 5.000 1.000 0.475 -10 -10 0.016 WXGU22**L/R... 0.66
A10-SWLXR/L2-D14 STEEL 0.875 0.625 0.531 7.000 1.250 0.600 -10 -8 0.016 WXGU22**L/R... 0.66
A12-SWLXR/L2-D16 STEEL 1.000 0.750 0.593 7.000 1.438 0.725 -10 -7 0.016 WXGU22**L/R... 0.66
A16-SWLXR/L2-D20 STEEL 1.250 1.000 0.625 7.000 1.438 0.938 -10 -7 0.016 WXGU22**L/R... 0.66
E06-SWLXR/L2-D08 CARBIDE 0.500 0.375 0.281 5.000 1.000 0.350 -10 -14 0.016 WXGU22**L/R... 0.66
E08-SWLXR/L2-D11 CARBIDE 0.688 0.500 0.406 5.000 1.063 0.475 -10 -10 0.016 WXGU22**L/R... 0.66
E10-SWLXR/L2-D14 CARBIDE 0.875 0.625 0.531 7.000 1.250 0.600 -10 -8 0.016 WXGU22**L/R... 0.66
E12-SWLXR/L2-D16 CARBIDE 1.000 0.750 0.593 7.000 1.438 0.725 -10 -7 0.016 WXGU22**L/R... 0.66
E16-SWLXR/L2-D20 CARBIDE 1.250 1.000 0.625 10.000 1.812 0.938 -10 -7 0.016 WXGU22**L/R... 0.66
*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius
Note: Right hand toolholders (R) are used with left hand inserts (L) Left hand toolholders (L) are used with right hand inserts (R)

SPARE PARTS
Designation Clamping screw Wrench
A/E**-SWLXR/L... SR34-514 T-7F

A/E-S DXXR /L
Fo r 5 5 ° r h o m b i c i n s e r t w i t h 4 e d g e s

øDm h
f

100°
15.5˚
øDs
α°
f2

L2
L1
θ°
Cutting edge style X Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A06-SDXXR/L2-D10 STEEL 0.625 0.375 0.406 5.000 0.750 0.350 0.213 -14 -12 0.016 DXGU22**L/R... 0.66
A08-SDXXR/L2-D11 STEEL 0.688 0.500 0.406 5.000 1.000 0.475 0.151 -13.5 -11 0.016 DXGU22**L/R... 0.66
A10-SDXXR/L2-D14 STEEL 0.875 0.625 0.531 7.000 1.250 0.600 0.213 -13 -9 0.016 DXGU22**L/R... 0.66
A12-SDXXR/L2-D16 STEEL 1.000 0.750 0.593 7.000 1.438 0.725 0.213 -13 -8 0.016 DXGU22**L/R... 0.66
A16-SDXXR/L2-D20 STEEL 1.250 1.000 0.625 7.000 1.438 0.938 0.120 -13 -8 0.016 DXGU22**L/R... 0.66
E06-SDXXR/L2-D10 CARBIDE 0.625 0.375 0.406 5.000 1.000 0.350 0.213 -14 -12 0.016 DXGU22**L/R... 0.66
E08-SDXXR/L2-D11 CARBIDE 0.688 0.500 0.406 5.000 1.063 0.475 0.151 -13.5 -11 0.016 DXGU22**L/R... 0.66
E10-SDXXR/L2-D14 CARBIDE 0.875 0.625 0.531 7.000 1.250 0.600 0.213 -13 -9 0.016 DXGU22**L/R... 0.66
E12-SDXXR/L2-D16 CARBIDE 1.000 0.750 0.593 7.000 1.438 0.725 0.213 -13 -8 0.016 DXGU22**L/R... 0.66
E16-SDXXR2-D20 CARBIDE 1.250 1.000 0.625 10.000 1.812 0.938 0.120 -13 -8 0.016 DXGU22**L/R... 0.66
*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius
Note: Right hand toolholders (R) are used with left hand inserts (L) Left hand toolholders (L) are used with right hand inserts (R)

SPARE PARTS
Designation Clamping screw Wrench
A/E**-SDXXR/L... SR34-514 T-7F

Reference pages
A/E-SWLXR/L: Inserts → B290, Standard cutting conditions → B293
A/E-SDXXR/L: Inserts → B291 -, Standard cutting conditions → B293

B288 www.tungaloyamerica.com
A-SDZXR /L
Fo r 5 5 ° r h o m b i c i n s e r t w i t h 4 e d g e s

øDm h
L2
93°

f
26˚
α°

øDs
L3

f2
L1
θ°

Int. Toolholder
Cutting edge style Z Right hand (R) shown.

Inch Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A08-SDZXR/L2-D10 STEEL 0.625 0.500 0.438 5.000 1.125 0.500 0.475 0.188 -10 -14 0.016 DXGU22**R/L... 0.66
A10-SDZXR/L2-D11 STEEL 0.688 0.625 0.500 7.000 1.250 0.500 0.600 0.188 -10 -12.5 0.016 DXGU22**R/L... 0.66
A12-SDZXR/L2-D14 STEEL 0.875 0.750 0.563 7.000 1.375 0.500 0.725 0.188 -10 -10.5 0.016 DXGU22**R/L... 0.66

*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius
Note: Right hand toolholders (R) are used with right hand inserts (R) Left hand toolholders (L) are used with left hand inserts (L)

SPARE PARTS
Designation Clamping screw Wrench
A**-SDZXR/L... SR34-514 T-7F

Reference pages
A/E-SDZXR/L: Inserts → B291 -, Standard cutting conditions → B293

Tungaloy B289
 C : Continuous cutting
L : Light interrupted cutting
INSERT H : Heavy interrupted cutting
P Steel L CL CL CL
POSITIVE TYPE M Stainless L CL
D O U B LE -SI D ED K Cast iron L CL CL C
N Non-ferrous C
Trigon, 80° S Superalloys C C
with hole H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
SH725
Int. Toolholder

Inch Metric
(Low cutting force) force) (Sharp edge) medium cutting cutting (Sharp edge)
Finishing to medium

JTS WXGU 220 MFR-JTS WXGU040301MFR-JTS <0.004"* 䖃

WXGU 220 MFL-JTS WXGU040301MFL-JTS <0.004"* 䖃

WXGU 220.5 MFR-JTS WXGU040302MFR-JTS <0.008"* 䖃

WXGU 220.5 MFL-JTS WXGU040302MFL-JTS <0.008"* 䖃

JTS WXGU 220 MR-JTS WXGU040301MR-JTS <0.004"* 䖃

Finishing to

WXGU 220 ML-JTS WXGU040301ML-JTS <0.004"* 䖃

WXGU 220.5 MR-JTS WXGU040302MR-JTS <0.008"* 䖃

WXGU 220.5 ML-JTS WXGU040302ML-JTS <0.008"* 䖃
Finishing (Low cutting

JSS WXGU 220 MFR-JSS WXGU040301MFR-JSS <0.004"* 䖃

WXGU 220 MFL-JSS WXGU040301MFL-JSS <0.004"* 䖃

WXGU 220.5 MFR-JSS WXGU040302MFR-JSS <0.008"* 䖃

WXGU 220.5 MFL-JSS WXGU040302MFL-JSS <0.008"* 䖃

JSS WXGU 220 MR-JSS WXGU040301MR-JSS <0.004"* 䖃

WXGU 220 ML-JSS WXGU040301ML-JSS <0.004"* 䖃
Finishing

WXGU 220.5 MR-JSS WXGU040302MR-JSS <0.008"* 䖃

WXGU 220.5 ML-JSS WXGU040302ML-JSS <0.008"* 䖃

TS WXGU 220.5 R TS WXGU040302R-TS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L TS WXGU040302L-TS 0.008" 䖃 䖃 䖃 䖃

medium cutting
Finishing to

WXGU 221 R TS WXGU040304R-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L TS WXGU040304L-TS 0.016" 䖃 䖃 䖃 䖃

WXGU 222 R TS WXGU040308R-TS 0.031" 䖃 䖃 䖃 䖃

WXGU 222 L TS WXGU040308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force) Finishing (Wiper)

TSW WXGU 221 R TSW WXGU040304R-TSW 0.016" 䖃 䖃 䖃

WXGU 221 L TSW WXGU040304L-TSW 0.016" 䖃 䖃 䖃

WXGU 222 R TSW WXGU040308R-TSW 0.031" 䖃 䖃 䖃

WXGU 222 L TSW WXGU040308L-TSW 0.031" 䖃 䖃 䖃

SS WXGU 220.5 R SS WXGU040302R-SS 0.008" 䖃 䖃 䖃 䖃

WXGU 220.5 L SS WXGU040302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

WXGU 221 R SS WXGU040304R-SS 0.016" 䖃 䖃 䖃 䖃

WXGU 221 L SS WXGU040304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

䖃㻌: Line up

B290 www.tungaloyamerica.com
 C : Continuous cutting
L : Light interrupted cutting
INSERT H : Heavy interrupted cutting
P Steel L CL
POSITIVE TYPE M Stainless L CL
DO U B LE-S I D ED K Cast iron L
Rhombic, 55° N Non-ferrous
with hole S Superalloys C
H Hard materials
Coated
Application

Corner
radius
Chipbreaker Designation

AH725
SH725

Int. Toolholder
Inch Metric
JRP DXGU 220-MFRE-JRP DXGU070301MFRE-JRP <0.004"* 䖃
(Sharp edge)

DXGU 220-MFLE-JRP DXGU070301MFLE-JRP <0.004"* 䖃

Finishing

DXGU 220.5-MFRE-JRP DXGU070302MFRE-JRP <0.008"* 䖃

DXGU 220.5-MFLE-JRP DXGU070302MFLE-JRP <0.008"* 䖃

䖃
Finishing (Low cutting Finishing to medium Finishing to medium
cutting (Sharp edge)

JTS DXGU 220-MFR-JTS DXGU070301MFR-JTS <0.004"*

DXGU 220-MFL-JTS DXGU070301MFL-JTS <0.004"* 䖃

DXGU 220.5-MFR-JTS DXGU070302MFR-JTS <0.008"* 䖃

DXGU 220.5-MFL-JTS DXGU070302MFL-JTS <0.008"* 䖃

JTS DXGU 220-MR-JTS DXGU070301MR-JTS <0.004"* 䖃

DXGU 220-ML-JTS DXGU070301ML-JTS <0.004"* 䖃
cutting

DXGU 220.5-MR-JTS DXGU070302MR-JTS <0.008"* 䖃

DXGU 220.5-ML-JTS DXGU070302ML-JTS <0.008"* 䖃

JSS DXGU 220-MFR-JSS DXGU070301MFR-JSS <0.004"* 䖃

force) (Sharp edge)

DXGU 220-MFL-JSS DXGU070301MFL-JSS <0.004"* 䖃

DXGU 220.5-MFR-JSS DXGU070302MFR-JSS <0.008"* 䖃

DXGU 220.5-MFL-JSS DXGU070302MFL-JSS <0.008"* 䖃

* Corner radius has minus tolerance.

䖃㻌: Line up

Tungaloy B291
 C : Continuous cutting
L : Light interrupted cutting
H : Heavy interrupted cutting

P Steel L CL CL
POSITIVE TYPE
M Stainless L
D O U B LE -SIDED
K Cast iron L CL CL C
N Non-ferrous C
Rhombic, 55° S Superalloys C C
with hole H Hard materials
Coated Coated Cermet Uncoated
cermet
Application

Corner
radius

NS9530
GT9530
Chipbreaker Designation

KS05F
AH725
Int. Toolholder

Inch Metric
(Low cutting force)

JSS DXGU 220 MR-JSS DXGU070301MR-JSS <0.004"* 䖃

DXGU 220 ML-JSS DXGU070301ML-JSS <0.004"* 䖃
Finishing

DXGU 220.5 MR-JSS DXGU070302MR-JSS <0.008"* 䖃

DXGU 220.5 ML-JSS DXGU070302ML-JSS <0.008"* 䖃

TS DXGU 220.5 TS DXGU070302R-TS 0.008" 䖃 䖃 䖃 䖃

Finishing to medium

DXGU 220.5 TS DXGU070302L-TS 0.008" 䖃 䖃 䖃 䖃

DXGU 221 TS DXGU070304R-TS 0.016" 䖃 䖃 䖃 䖃

cutting

DXGU 221 TS DXGU070304L-TS 0.016" 䖃 䖃 䖃 䖃

DXGU 222 TS DXGU070308R-TS 0.031" 䖃 䖃 䖃 䖃

DXGU 222 TS DXGU070308L-TS 0.031" 䖃 䖃 䖃 䖃

(Low cutting force)

SS DXGU 220.5 SS DXGU070302R-SS 0.008" 䖃 䖃 䖃 䖃

DXGU 220.5 SS DXGU070302L-SS 0.008" 䖃 䖃 䖃 䖃

Finishing

DXGU 221 SS DXGU070304R-SS 0.016" 䖃 䖃 䖃 䖃

DXGU 221 SS DXGU070304L-SS 0.016" 䖃 䖃 䖃 䖃

* Corner radius has minus tolerance.

P Steel CL
POSITIVE TYPE M Stainless CL
D O U B LE -SIDED K Cast iron
N Non-ferrous
Rhombic, 35° S Superalloys
with hole H Hard materials
Coated
Application

Corner
radius

Chipbreaker Designation
SH725

Inch Metric

JRP VXGU 73.50 MFRE-JRP VXGU09T201MFRE-JRP <0.004"* 䖃

(Sharp edge)

VXGU 73.50 MFLE-JRP VXGU09T201MFLE-JRP <0.004"* 䖃

Finishing

VXGU 73.50.5 MFRE-JRP VXGU09T202MFRE-JRP <0.008"* 䖃

VXGU 73.50.5 MFLE-JRP VXGU09T202MFLE-JRP <0.008"* 䖃

* Corner radius has minus tolerance. 䖃㻌: Line up

B292 www.tungaloyamerica.com
 STAN DAR D CUT T ING CONDIT IONS
F O R I N T E RN AL TU R N IN G
Grade
Cutting Depth of
For wear Feed
ISO Workpiece material For surface speed cut
First Choice resistance f (ipr)
finish Vc (sfm) ap (in)
(High speed)
AH725 - - 164 - 591 0.012 - 0.080 0.003 - 0.012
Low carbon steel
- NS9530 - 262 - 820 0.012 - 0.080 0.003 - 0.012
(1025, etc.)
- - GT9530 262 - 984 0.012 - 0.080 0.003 - 0.012

Int. Toolholder
AH725 - - 164 - 591 0.012 - 0.080 0.003 - 0.012
Carbon steel
- NS9530 - 262 - 820 0.012 - 0.080 0.003 - 0.012
(1045, 1055, etc.)
- - GT9530 262 - 984 0.012 - 0.080 0.003 - 0.012
AH725 - - 164 - 591 0.012 - 0.080 0.003 - 0.012
Low alloy steel
- NS9530 - 262 - 820 0.012 - 0.080 0.003 - 0.012
(4140, etc.)
- - GT9530 262 - 984 0.012 - 0.080 0.003 - 0.012
AH725 - - 164 - 591 0.012 - 0.080 0.003 - 0.012
Alloy steel
- NS9530 - 262 - 820 0.012 - 0.080 0.003 - 0.012
(5120, etc.)
- - GT9530 262 - 984 0.012 - 0.080 0.003 - 0.012

Stainless steel (Austenitic)

AH725 - - 164 - 492 0.012 - 0.080 0.003 - 0.012
(304, etc.)

Stainless steel (Martensitic and ferritic)

AH725 - - 164 - 492 0.012 - 0.080 0.003 - 0.012
(430, etc.)

Stainless steel (Precipitation hardening)

AH725 - - 164 - 492 0.012 - 0.080 0.003 - 0.012
(174, etc.)

AH725 - - 164 - 591 0.012 - 0.080 0.003 - 0.012

Grey cast iron
- NS9530 - 262 - 820 0.012 - 0.080 0.003 - 0.012
(No.250B, etc.)
- - GT9530 262 - 984 0.012 - 0.080 0.003 - 0.012
AH725 - - 164 - 394 0.012 - 0.080 0.003 - 0.012
Ductile cast iron
- NS9530 - 262 - 492 0.012 - 0.080 0.003 - 0.012
(80-55-60, etc.)
- - GT9530 262 - 591 0.012 - 0.080 0.003 - 0.012

Non ferrous Metal

KS05F - - 328 - 984 0.012 - 0.080 0.003 - 0.012
(Aluminum alloy, etc.)

Non ferrous Metal

KS05F - - 328 - 984 0.012 - 0.080 0.003 - 0.012
(Cu Alloy, etc.)

Tungaloy B293
 A-AC LN R /L-Eco
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h

f
95°
L2

øDs
f2
α° L1

θ°
Int. Toolholder

Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-ACLNR/L33-D20 STEEL 1.25 1.00 0.672 12 1.750 0.906 0.172 -6 -13 0.031 CN**33... 2.2
A20-ACLNR/L33-D25 STEEL 1.56 1.25 0.859 14 1.938 1.188 0.234 -6 -10 0.031 CN**33... 2.2

*Torque: Recommended torque (Ibf·ft) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ACLNR/L33... ACP3S-E ACS-5W BP-7 SP-2.5 ASC322 CSTB-3.5 T-15F

A-PC LN R /L-Eco
Le v e r c l a m p b o r i n g b a r s , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h
95°
f

L2

øDs
f2

α° L1
95°
θ°
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16M-PCLNR/L0904-D200 STEEL 20 16 11 150 32 15 3 -6 -16 0.8 CN**0904... 1.7
A20Q-PCLNR/L0904-D250 STEEL 25 20 13 180 36 18 3 -6 -12 0.8 CN**0904... 1.7

*Torque: Recommended torque (N·m) for clamping **rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Clamping screw Wrench Lever
(Optional parts) (Optional parts)
A16M-PCLNR/L0904-D200 LCS33 P-2F LCL33N - (SSHM3-4)
A20Q-PCLNR/L0904-D250 LCS33 P-2F LCL33N (EA20) (SSHM3-4)

Reference pages
A-ACLNR/L-Eco, A-PCLNR/L-Eco: Inserts → B052 -

B294 www.tungaloyamerica.com
A-AW LN R /L-Eco
Double-clamp boring bars, for negative trigon inserts

øDm h

f
95°
L2

f2

øDs
α° L1

θ°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-AWLNR/L33-D20 STEEL 1.25 1.00 0.672 12 1.750 0.906 0.172 -6 -13 0.031 WN**33... 2.2
A20-AWLNR/L33-D25 STEEL 1.56 1.25 0.859 14 1.938 1.188 0.234 -6 -10 0.031 WN**33... 2.2

*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-AWLNR/L33... ACP3S-E ACS-5W BP-7 SP-2.5 ASW322 CSTB-3.5 T-15F

A-P W LN R /L-E co
Le v e r c l a m p b o r i n g b a r s , f o r n e g a t i v e t r i g o n i n s e r t s

95°
øDm h
f

L2

øDs
f2

α° L1
95°
θ°
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16M-PWLNR/L0604-D200 STEEL 20 16 11 150 32 15 3 -8 -17 0.8 WN**0604... 1.7
A20Q-PWLNR/L0604-D250 STEEL 25 20 13 180 36 18 3 -6 -14 0.8 WN**0604... 1.7

*Torque: Recommended torque (N·m) for clamping **rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Clamping screw Wrench Lever
(Optional parts) (Optional parts)
A16M-PWLNR/L0604-D200 LCS33 P-2F LCL33N - (SSHM3-4)
A20Q-PWLNR/L0604-D250 LCS33 P-2F LCL33N (EA-20) (SSHM3-4)

Reference pages
A-AWLNR/L-Eco, A-PWLNR/L-Eco: Inserts → B097 -

Tungaloy B295
 A-PTFN R /L-Eco
Le v e r c l a m p b o r i n g b a r s , f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h

f
91°
L2

øDs
f2
α° L1

θ°
Int. Toolholder

Cutting edge style F Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A25R-PTFNR/L1104-D320 STEEL 32 25 17 200 45 23 1.31 -6 -12 0.8 TN**1104... 2
A32S-PTFNR/L1104-D400 STEEL 40 32 22 250 50 30 1.25 -6 -10 0.8 TN**1104... 2

*Torque: Recommended torque (N·m) for clamping **rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Clamping screw Wrench Lever
(Optional parts) (Optional parts)
A25R-PTFNR/L... LCS23A P-2.5 LCL23 (EA-25) (SSHM4-5)
A32S-PTFNR/L... LCS23A P-2.5 LCL23 (EA-32) (SSHM4-5)

A-AD U N R /L-Eco
Double-clamp boring bars, for negative 55° rhombic inserts

øDm h
f

93°
20°
L2

øDs
α°
f2

L1

θ°
Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-ADUNR/L33-D20 STEEL 1.25 1.00 0.672 12 1.750 0.906 0.172 -6 -13 0.031 DN**33... 2.2
A20-ADUNR/L33-D25 STEEL 1.56 1.25 0.859 14 1.938 1.188 0.234 -6 -11 0.031 DN**33... 2.2

*Torque: Recommended torque (lb·ft) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ADUNR/L... ACP3S-E ACS-5W BP-7 SP-2.5 ASD322 CSTB-3.5 T-15F

Reference pages
A-PTFNR/L-Eco: Inserts →B082 -
A-ADUNR/L-Eco: Inserts → B063 -

B296 www.tungaloyamerica.com
A-P D U N R /L-E c o
Le v e r c l a m p b o r i n g b a r s , f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h

f
93°

L2

øDs
f2
α° L1
θ°

Int. Toolholder
Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A20Q-PDUNR/L1104-D250 STEEL 25 20 13 180 36 18 3 -6 -14 0.8 DN**1104... 1.7

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (PDUNL ** type), and the left hand insert (L) is used for the right hand
toolholders (PDUNR ** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Clamping screw Wrench Lever
(Optional parts) (Optional parts)
A20Q-PDUNR/L1104-D250 LCS22A P-2F LCL33NL (EA-20) (SSHM2.5-3)

A-P TU N R /L-Eco
Le v e r c l a m p b o r i n g b a r s , f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h
f

93°

øDs
L2
f2

α° L1
θ°
Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A25R-PTUNR/L1104-D320 STEEL 32 25 17 200 45 23 1.22 -6 -12 0.8 TN**1104... 2
A32S-PTUNR/L1104-D400 STEEL 40 32 22 250 50 30 1.16 -6 -10 0.8 TN**1104... 2

*Torque: Recommended torque (N·m) for clamping **rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Clamping screw Wrench Lever
(Optional parts) (Optional parts)
A25R-PTUNR/L1104-D320 LCS23A P-2.5 LCL23 (EA-25) (SSHM4-5)
A32S-PTUNR/L1104-D400 LCS23A P-2.5 LCL23 (EA-32) (SSHM4-5)

Reference pages
A-PDUNR/L-Eco: Inserts → B063 -
A-PTUNR/L-Eco: Inserts →B082 -

Tungaloy B297
 A -P VU N R /L-Eco
Le v e r l o c k t y p e b o r i n g b a r s . Fo r n e g a t i v e 3 5 ° r h o m b i c i n s e r t .

øDs
øDm

f
93°
50˚

f2
L2 L1

α°
θ°
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-PVUNR/L2.33-D20 STEEL 1.250 1.000 0.672 12.000 1.750 0.906 0.197 -6 -13 0.031 VN**2.33**E... 2.2
A16-PVUNR/L2.33-D24 STEEL 1.500 1.000 0.859 12.000 1.750 0.906 0.315 -6 -10 0.031 VN**2.33**E... 2.2
A20-PVUNR/L2.33-D26 STEEL 1.650 1.250 0.859 14.000 2.000 1.188 0.217 -6 -10 0.031 VN**2.33**E... 2.2
*Torque: Recommended torque (lb·ft) for clamping **rε: Standard corner radius

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A25R-PVUNR/L1204-D320 STEEL 32 25 18 200 45 23 5.0 -5 -15 0.8 VN**1204... 3
A25R-PVUNR/L1204-D370 STEEL 37 25 22 200 45 23 8.0 -4 -15 0.8 VN**1204... 3
A32S-PVUNR/L1204-D400 STEEL 40 32 22 250 50 30 5.5 -6 -12 0.8 VN**1204... 3
*Torque: Recommended torque (N・m) for clamping **rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench Lever Shim Spring pin Oil supply attachment Coolant screw
A16-PVUNR/L2.33-D20
A16-PVUNR/L2.33-D24
LCS3V P-2.5 LCL3V LSV212 LSP3 EA-25 SSHM4-5
A25R-PVUNR/L1204-D320
A25R-PVUNR/L1204-D370
A20-PVUNR/L2.33-D26
LCS3V P-2.5 LCL3V LSV212 LSP3 EA-32 SSHM4-5
A32S-PVUNR/L1204-D400

Reference pages
A-PVUNR/L-Eco: Inserts →B093 -

B298 www.tungaloyamerica.com
A /E-S C LC R /L
S c re w -o n b o r i n g b ar s, f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h
95°

f
L2

øDs
α° L1
θ°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A06-SCLCR/L2-D08 STEEL 0.500 0.375 0.281 5.00 0.750 0.350 0 -9 0.016 CC**21.5... 0.9
A08-SCLCR/L2-D11 STEEL 0.687 0.500 0.406 5.00 1.000 0.475 0 -6 0.016 CC**21.5... 0.9
A10-SCLCR/L3-D14 STEEL 0.875 0.625 0.531 7.00 1.250 0.600 0 -7 0.016 CC**32.5... 2.2
A12-SCLCR/L3-D16 STEEL 1.000 0.750 0.594 7.00 1.438 0.725 0 -5 0.031 CC**32.5... 2.2
A16-SCLCR/L3-D20 STEEL 1.250 1.000 0.687 7.00 1.750 0.975 0 -4 0.031 CC**32.5... 2.2
E06-SCLCR/L2-D08 CARBIDE 0.500 0.375 0.281 5.00 0.750 0.350 0 -9 0.016 CC**21.5... 0.9
E08-SCLCR/L2-D11 CARBIDE 0.688 0.500 0.406 5.00 1.000 0.475 0 -6 0.016 CC**21.5... 0.9
E10-SCLCR/L2-D14 CARBIDE 0.875 0.625 0.531 7.00 1.250 0.600 0 -7 0.016 CC**21.5... 0.9
E10-SCLCR/L3-D14 CARBIDE 0.875 0.625 0.531 7.00 1.250 0.600 0 -7 0.016 CC**32.5... 2.2
E12-SCLCR/L3-D16 CARBIDE 1.000 0.750 0.594 7.00 1.438 0.725 0 -5 0.031 CC**32.5... 2.2
E16-SCLCR/L3-D20 CARBIDE 1.250 1.000 0.687 10.00 1.750 0.975 0 -4 0.031 CC**32.5... 2.2

*Torque: Recommended torque (lb·ft) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLCL** type), and the left hand insert (L) is used for the right
hand toolholders (SCLCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SCLCR/L2-D... CSTB-2.5S T-8F
A**-SCLCR/L3-D... CSTB-4S T-15F
E06-SCLCR/L2-D08 CSTB-2.5S T-8F
E**-SCLCR/L2-D... CSTB-2.5B T-8F
E**-SCLCR/L3-D... CSTB-4S T-15F

Reference pages
A/E-SCLCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179

Tungaloy B299
 A /E -SC LC R / L

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A04F-SCLCR/L03-D050 STEEL 5 4 2.5 80 8 3.8 0 -15 0.2 CC**03X1... 0.6
A05F-SCLCR/L03-D060 STEEL 6 5 3 80 9 4.8 0 -13 0.2 CC**03X1... 0.6
A06G-SCLCR/L04-D070 STEEL 7 6 3.5 90 11 5.75 0 -13 0.2 CC**04T1... 0.6
A07G-SCLCR/L04-D080 STEEL 8 7 4 90 12 6.75 0 -11 0.2 CC**04T1... 0.6
A08H-SCLCR/L06-D100 STEEL 10 8 5.5 100 16 7.5 0 -13 0.4 CC**0602... 1.2
A10F-SCLCR06-D120 STEEL 12 10 6 80 20 9 0 -10 0.4 CC**0602... 1.2
Int. Toolholder

A10K-SCLCR/L06-D120 STEEL 12 10 6 125 20 9 0 -10 0.4 CC**0602... 1.2

A12H-SCLCR06-D140 STEEL 14 12 7 100 24 11 0 -8 0.4 CC**0602... 1.2
A12M-SCLCR/L06-D140 STEEL 14 12 7 150 24 11 0 -8 0.4 CC**0602... 1.2
A12H-SCLCR06-D160 STEEL 16 12 9 100 24 11 0 -7 0.4 CC**0602... 1.2
A12M-SCLCR/L06-D160 STEEL 16 12 9 150 24 11 0 -7 0.4 CC**0602... 1.2
A16K-SCLCR09-D180 STEEL 18 16 9 125 32 15 0 -9 0.8 CC**09T3... 3
A16Q-SCLCR/L09-D180 STEEL 18 16 9 180 32 15 0 -10 0.8 CC**09T3... 3
A16K-SCLCR09-D200 STEEL 20 16 11 125 32 15 0 -9 0.8 CC**09T3... 3
A16Q-SCLCR/L09-D200 STEEL 20 16 11 180 32 15 0 -9 0.8 CC**09T3... 3
A20R-SCLCR/L09-D220 STEEL 22 20 11 200 32 18 0 -8 0.8 CC**09T3... 3
A25S-SCLCR/L09-D270 STEEL 27 25 13.5 250 45 23 0 -6 0.8 CC**09T3... 3
E04G-SCLCR/L03-D050 CARBIDE 5 4 2.5 90 9 3.8 0 -15 0.2 CC**03X1... 0.6
E05G-SCLCR/L03-D060 CARBIDE 6 5 3 90 10 4.8 0 -13 0.2 CC**03X1... 0.6
E06H-SCLCR/L04-D070 CARBIDE 7 6 3.5 100 12 5.75 0 -13 0.2 CC**04T1... 0.6
E07H-SCLCR/L04-D080 CARBIDE 8 7 4 100 14 6.75 0 -11 0.2 CC**04T1... 0.6
E08G-SCLCR06-D100 CARBIDE 10 8 5.5 90 22 7.5 0 -13 0.4 CC**0602... 1.2
E08K-SCLCR/L06-D100 CARBIDE 10 8 5.5 125 22 7.5 0 -13 0.4 CC**0602... 1.2
E10F-SCLCR06-D120 CARBIDE 12 10 6 80 25 9 0 -10 0.4 CC**0602... 1.2
E10H-SCLCR06-D120 CARBIDE 12 10 6 100 25 9 0 -10 0.4 CC**0602... 1.2
E10M-SCLCR/L06-D120 CARBIDE 12 10 6 150 25 9 0 -10 0.4 CC**0602... 1.2
E12G-SCLCR06-D140 CARBIDE 14 12 7 90 27 11 0 -8 0.4 CC**0602... 1.2
E12J-SCLCR06-D140 CARBIDE 14 12 7 110 27 11 0 -8 0.4 CC**0602... 1.2
E12Q-SCLCR/L06-D140 CARBIDE 14 12 7 180 27 11 0 -8 0.4 CC**0602... 1.2
E12G-SCLCR06-D160 CARBIDE 16 12 9 90 27 11 0 -7 0.4 CC**0602... 1.2
E12J-SCLCR06-D160 CARBIDE 16 12 9 110 27 11 0 -7 0.4 CC**0602... 1.2
E12Q-SCLCR/L06-D160 CARBIDE 16 12 9 180 27 11 0 -7 0.4 CC**0602... 1.2
E16H-SCLCR09-D180 CARBIDE 18 16 9 100 32 15 0 -10 0.8 CC**09T3... 3
E16L-SCLCR09-D180 CARBIDE 18 16 9 130 32 15 0 -10 0.8 CC**09T3... 3
E16R-SCLCR/L09-D180 CARBIDE 18 16 9 200 32 15 0 -10 0.8 CC**09T3... 3
E16H-SCLCR09-D200 CARBIDE 20 16 11 100 32 15 0 -9 0.8 CC**09T3... 3
E16L-SCLCR09-D200 CARBIDE 20 16 11 130 32 15 0 -9 0.8 CC**09T3... 3
E16R-SCLCR/L09-D200 CARBIDE 20 16 11 200 32 15 0 -9 0.8 CC**09T3... 3
E20S-SCLCR09-D220 CARBIDE 22 20 11 250 36 18 0 -8 0.8 CC**09T3... 3
E25T-SCLCR09-D270 CARBIDE 27 25 13.5 300 45 23 0 -6 0.8 CC**09T3... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLCL** type), and the left hand insert (L) is used for the right
hand toolholders (SCLCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SCLCR/L03-D... CSTA-1.6 T-6F
A**-SCLCR/L04-D... CSTB-2 T-6F
A**-SCLCR/L06-D... CSTB-2.5S T-8F
A**-SCLCR/L09-D... CSTB-4S T-15F
E**-SCLCR/L03-D... CSTA-1.6 T-6F
E**-SCLCR/L04-D... CSTB-2 T-6F
E**-SCLCR/L06-D... CSTB-2.5S T-8F
E16*-SCLCR/L09-D... CSTB-4L060 T-15F
E2**-SCLCR/L09-D... CSTB-4S T-15F

Reference pages
A/E-SCLCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179

B300 www.tungaloyamerica.com
S /A/C /E-S C LCR/L
S c re w -o n b o r i n g b ar s, f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h
95°

f
L2 L1
α°

øDs
θ°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° Insert

S06-SCLCR/L2 STEEL 0.500 0.375 0.250 5.00 0.980 0.335 0 12 CC**21.5...
S08-SCLCR/L2 STEEL 0.625 0.500 0.313 6.00 0.980 0.461 0 10 CC**21.5...
S10-SCLCR/L3 STEEL 0.813 0.625 0.406 7.00 1.180 0.547 0 10 CC**32.5...
S12-SCLCR/L3 STEEL 1.000 0.750 0.500 8.00 1.380 0.670 0 8 CC**32.5...
A05-SCLCR/L2 STEEL WITH HOLE 0.375 0.312 0.219 4.50 - 0.280 0 15 CC**21.5...
A06-SCLCR/L2 STEEL WITH HOLE 0.437 0.375 0.250 4.75 - 0.350 0 15 CC**21.5...
A08-SCLCR/L2 STEEL WITH HOLE 0.562 0.500 0.313 5.00 - 0.475 0 15 CC**21.5...
A08-SCLCR/L3 STEEL WITH HOLE 0.562 0.500 0.313 5.00 - 0.475 0 15 CC**32.5...
A10-SCLCR/L2 STEEL WITH HOLE 0.718 0.625 0.406 7.00 - 0.600 0 12 CC**21.5...
A10-SCLCR/L3 STEEL WITH HOLE 0.718 0.625 0.406 7.00 - 0.600 0 12 CC**32.5...
A12-SCLCR/L3 STEEL WITH HOLE 0.875 0.750 0.500 7.00 - 0.725 0 8 CC**32.5...
A16-SCLCR/L3 STEEL WITH HOLE 1.280 1.000 0.640 7.00 - 0.975 0 4 CC**32.5...
C06-SCLCR/L2 CARBIDE 0.470 0.375 0.245 5.00 - 0.350 0 15 CC**21.5...
C08-SCLCR/L2 CARBIDE 0.592 0.500 0.308 5.00 - 0.475 0 15 CC**21.5...
C10-SCLCR/L2 CARBIDE 0.760 0.625 0.401 7.00 - 0.600 0 12 CC**21.5...
C10-SCLCR/L3 CARBIDE 0.760 0.625 0.401 7.00 - 0.600 0 12 CC**32.5...
C12-SCLCR/L3 CARBIDE 0.920 0.750 0.495 7.00 - 0.725 0 8 CC**32.5...
C16-SCLCR/L3 CARBIDE 1.280 1.000 0.640 7.00 - - 0 - CC**32.5...
E06-SCLCR/L2 CARBIDE W/HOLE 0.470 0.375 0.245 5.00 - 0.350 0 15 CC**21.5...
E08-SCLCR/L2 CARBIDE W/HOLE 0.592 0.500 0.308 5.00 - 0.475 0 15 CC**21.5...
E10-SCLCR/L2 CARBIDE W/HOLE 0.760 0.625 0.401 7.00 - 0.600 0 12 CC**21.5...
E10-SCLCR/L3 CARBIDE W/HOLE 0.760 0.625 0.401 7.00 - 0.600 0 12 CC**32.5...
E12-SCLCR/L3 CARBIDE W/HOLE 0.920 0.750 0.495 7.00 - 0.725 0 8 CC**32.5...
E16-SCLCR/L3 CARBIDE W/HOLE 1.250 1.000 0.687 7.00 - 0.975 0 4 CC**32.5...

SPARE PARTS
Designation Clamping screw Wrench
S**-SCLCR/L2 CSTB-2.5 T-8F
S**-SCLCR/L3 CSTB-4S T-15F
A0*-SCLCR/L2 CSTB-2.5 T-8F
A08-SCLCR/L3 CSTB-4S T-15F
A10-SCLCR/L2 CSTB-2.5 T-8F
A1*-SCLCR/L3 CSTB-4S T-15F
C**-SCLCR/L2 CSTB-2.5 T-8F
C**-SCLCR/L3 CSTB-4S T-15F
E**-SCLCR/L2 CSTB-2.5 T-8F
E**-SCLCR/L3 CSTB-4S T-15F

Reference pages
S/A/C/E-SCLCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179

Tungaloy B301
 A /E -SEXP R / L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 7 5 ° r h o m b i c i n s e r t s

øDs
øDm h

100°

f
L2

f
α° L1 L1

øDs
θ° Straight shank
style
Int. Toolholder

Cutting edge style X Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A05-SEXPR/L04-D04 STEEL 0.250 0.313 0.125 5.000 0.812 0.287 0 -12 0.016 EPGT52... 0.44
E05-SEXPR04-D04 CARBIDE 0.250 0.313 0.125 5.000 1.562 0.287 0 -12 0.016 EPGT52... 0.44

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A04F-SEXPR/L03-D045 STEEL 4.5 4 2.3 80 8 3.8 0 -15 0.2 EP**03X1... 0.6
A04F-SEXPR/L03-D050 STEEL 5 4 2.5 80 8 3.8 0 -13 0.2 EP**03X1... 0.6
A05F-SEXPR/L04-D055 STEEL 5.5 5 2.75 80 9 4.8 0 -12 0.4 EP**0401... 0.6
A06G-SEXPR/L04-D070 STEEL 7 6 3.6 90 11 5.75 0 -12 0.4 EP**0401... 0.6
A08H-SEXPR/L04-D055 STEEL 5.5 8 2.75 100 16 7.5 0 -12 0.4 EP**0401... 0.6
A08H-SEXPR/L04-D070 STEEL 7 8 3.6 100 20 7.5 0 -12 0.4 EP**0401... 0.6
E04G-SEXPR/L03-D045 CARBIDE 4.5 4 2.3 90 9 3.8 0 -15 0.2 EP**03X1... 0.6
E04G-SEXPR/L03-D050 CARBIDE 5 4 2.5 90 9 3.8 0 -13 0.2 EP**03X1... 0.6
E05G-SEXPR/L04-D055 CARBIDE 5.5 5 2.75 90 10 4.8 0 -12 0.4 EP**0401... 0.6
E06H-SEXPR/L04-D070 CARBIDE 7 6 3.6 100 12 5.75 0 -12 0.4 EP**0401... 0.6
E08K-SEXPR/L04-D055 CARBIDE 5.5 8 2.75 125 28 7.5 0 -12 0.4 EP**0401... 0.6
E08K-SEXPR/L04-D070 CARBIDE 7 8 3.6 125 40 7.5 0 -12 0.4 EP**0401... 0.6

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SEXPL** type), and the left hand insert (L) is used for the right
hand toolholders (SEXPR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SEXPR/L03-D... CSTA-1.6 T-6F
A**-SEXPR/L04-D... CSTB-2 T-6F
E**-SEXPR/L03-D... CSTA-1.6 T-6F
E**-SEXPR/L04-D... CSTB-2 T-6F

Reference pages
A/E-SEXPR/L: Inserts → B124 -, CBN → B173, PCD → B180

B302 www.tungaloyamerica.com
A /E-S C LPR /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h
95°

L2

øDs
L1

f
α°

θ°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A06-SCLPR/L2-D08 STEEL 0.500 0.375 0.281 5.00 0.750 0.350 5 -5 0.016 CP**21.5... 0.9
A08-SCLPR/L2-D11 STEEL 0.687 0.500 0.406 5.00 1.000 0.475 5 -2 0.016 CP**21.5... 0.9
A10-SCLPR/L3-D14 STEEL 0.875 0.625 0.531 7.00 1.250 0.600 5 -2 0.016 CP**32.5... 2.2
E06-SCLPR/L2-D08 CARBIDE 0.500 0.375 0.281 5.00 0.750 0.350 0 -9 0.016 CP**21.5... 0.9
E08-SCLPR/L2-D11 CARBIDE 0.688 0.500 0.406 5.00 1.000 0.475 0 -6 0.016 CP**21.5... 0.9
E10-SCLPR/L3-D14 CARBIDE 0.875 0.625 0.531 7.00 1.250 0.600 0 -7 0.032 CP**32.5... 2.2

*Torque: Recommended torque (lb·ft) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLPL** type), and the left hand insert (L) is used for the right
hand toolholders (SCLPR** type).

SPARE PARTS
Designation Clamping screw Wrench
A06-SCLPR/L2-D08 CSTB-2.5L042 T-8F
A08-SCLPR/L2-D11 CSTB-2.5S T-8F
A10-SCLPR/L3-D14 CSTB-4L070 T-15F
E06-SCLPR/L2-D08 CSTB-2.5S T-8F
E08-SCLPR/L2-D11 CSTB-2.5B T-8F
E10-SCLPR/L3-D14 CSTB-4S T-15F

Reference pages
A/E-SCLPR/L: Inserts → B113 -

Tungaloy B303
 A /E -SC LP R / L

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A08H-SCLPR/L06-D100 STEEL 10 8 5.5 100 16 7.5 5 -8 0.4 CP**0602... 1.2
A10K-SCLPR/L06-D120 STEEL 12 10 6 125 20 9 5 -5 0.4 CP**0602... 1.2
A10K-SCLPR/L08-D120 STEEL 12 10 6 125 20 9 5 -5 0.4 CP**0802... 1.4
A12M-SCLPR/L06-D140 STEEL 14 12 7 150 24 11 5 -4 0.4 CP**0602... 1.2
A12M-SCLPR/L08-D140 STEEL 14 12 7 150 24 11 5 -4 0.4 CP**0802... 1.4
A12M-SCLPR/L08-D160 STEEL 16 12 9 150 24 11 5 -3 0.4 CP**0802... 1.4
Int. Toolholder

A16Q-SCLPR/L09-D180 STEEL 18 16 9 180 32 15 5 -3.5 0.8 CP**0903... 3

A16Q-SCLPR/L09-D200 STEEL 20 16 11 180 32 15 5 -3 0.8 CP**0903... 3
A20R-SCLPR/L09-D220 STEEL 22 20 11 200 36 18 5 -2 0.8 CP**0903... 3
A25S-SCLPR/L09-D270 STEEL 27 25 13.5 250 45 23 5 -1 0.8 CP**0903... 3
E08K-SCLPR/L06-D100 CARBIDE 10 8 5.5 125 22 7.5 5 -8 0.4 CP**0602... 1.2
E10M-SCLPR/L06-D120 CARBIDE 12 10 6 150 25 9 5 -5 0.4 CP**0602... 1.2
E10H-SCLPR08-D120 CARBIDE 12 10 6 100 25 9 5 -5 0.4 CP**0802... 1.4
E10M-SCLPR/L08-D120 CARBIDE 12 10 6 150 25 9 5 -5 0.4 CP**0802... 1.4
E12Q-SCLPR/L06-D140 CARBIDE 14 12 7 180 27 11 5 -4 0.4 CP**0602... 1.2
E12G-SCLPR08-D140 CARBIDE 14 12 7 90 27 11 5 -4 0.4 CP**0802... 1.4
E12J-SCLPR08-D140 CARBIDE 14 12 7 110 27 11 5 -4 0.4 CP**0802... 1.4
E12Q-SCLPR/L08-D140 CARBIDE 14 12 7 180 27 11 5 -4 0.4 CP**0802... 1.4
E12G-SCLPR08-D160 CARBIDE 16 12 9 90 27 11 5 -3 0.4 CP**0802... 1.4
E12J-SCLPR08-D160 CARBIDE 16 12 9 110 27 11 5 -3 0.4 CP**0802... 1.4
E12Q-SCLPR/L08-D160 CARBIDE 16 12 9 180 27 11 5 -3 0.4 CP**0802... 1.4
E16H-SCLPR09-D180 CARBIDE 18 16 9 100 32 15 5 -3.5 0.8 CP**0903... 3
E16L-SCLPR09-D180 CARBIDE 18 16 9 130 32 15 5 -3.5 0.8 CP**0903... 3
E16R-SCLPL09-D180 CARBIDE 18 16 9 200 32 15 5 -3.5 0.8 CP**0903... 3
E16H-SCLPR09-D200 CARBIDE 20 16 11 100 32 15 5 -3 0.8 CP**0903... 3
E16L-SCLPR09-D200 CARBIDE 20 16 11 130 32 15 5 -3 0.8 CP**0903... 3
E16R-SCLPL09-D200 CARBIDE 20 16 11 200 32 15 5 -3 0.8 CP**0903... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLPL** type), and the left hand insert (L) is used for the right
hand toolholders (SCLPR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SCLPR/L06-D... CSTB-2.5S T-8F
A10K-SCLPR/L08-D120 CSTB-3L042 T-9F
A12M-SCLPR/L08-D... CSTB-3L050 T-9F
A**-SCLPR/L09-D... CSTB-4L060 T-15F
E**-SCLPR/L06-D... CSTB-2.5S T-8F
E10*-SCLPR/L08-D... CSTB-3L042 T-9F
E12*-SCLPR/L08-D... CSTB-3L050 T-9F
E16*-SCLPR/L09-D... CSTB-4L060 T-15F

Reference pages
A/E-SCLPR/L: Inserts → B113 -

B304 www.tungaloyamerica.com
J S -S E X PR /L
S c re w - o n b o r i n g b a r, f o r p o s i t i v e 7 5 ° r h o m b i c i n s e r t s

h
100° øDm

øDs
f
L2
α° L1

Int. Toolholder
Cutting edge style X Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h α° rε** Insert Torque*

JS08H-SEXPR045 STEEL 5.5 8 2.7 100 16 7 12 0.4 EP**0401... 0.6
JS08H-SEXPR047 STEEL 7 8 3.6 100 20 7 12 0.4 EP**0401... 0.6

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SEXPL** type), and the left hand insert (L) is used for the right
hand toolholders (SEXPR** type).

SPARE PARTS
Designation Clamping screw Wrench
JS08H-SEXPR04... CSTB-2 T-6F

Reference pages
JS-SEXPR/L: Inserts → B124, CBN → B173, PCD → B180

Tungaloy B305
 A -SV JB R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h

f
142°
L2
α°

øDs
L1

θ°
Int. Toolholder

Cutting edge style J Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A10-SVJBR2-D16 STEEL 1.000 0.625 0.156 7.000 1.250 0.600 -5 -6 0.016 VB**22... 0.89

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A20R-SVJBR/L11-D250 STEEL 25 20 2 200 40 18 -5 -5 0.4 VB**1103... 1.2
A25S-SVJBR/L11-D300 STEEL 30 25 3.5 250 50 23 -5 -5 0.4 VB**1103... 1.2

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVJBL** type), and the left hand insert (L) is used for the right
hand toolholders (SVJBR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SVJB**-D... CSTB-2.5 T-8F

A -SV JC R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h
f

142°
α° L2

øDs
L1

θ°
Cutting edge style J Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A10-SVJCR2-D16 STEEL 1.000 0.625 0.156 7.000 1.750 0.600 -5 -6 0.016 VC**22.. 0.89

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A12M-SVJCR/L08-D160 STEEL 16 12 2 150 28 11 -5 -5 0.4 VC**0802... 0.6
A16Q-SVJCR/L08-D200 STEEL 20 16 2 180 35 15 -5 -5 0.4 VC**0802... 0.6

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVJCL** type), and the left hand insert (L) is used for the right
hand toolholders (SVJCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A10-SVJCR2-D16 CSTB-2.5 T-8F
A**-SVJC*08-D... CSTB-2L T-6F

Reference pages
A-SVJBR/L: Inserts → B147 -, CBN → B171 -
A-SVJCR/L: Inserts → B149 -

B306 www.tungaloyamerica.com
A -S S K P R
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e s q u a re i n s e r t s

øDm h

f
75°
L2

øDs
α° L1

θ°

Int. Toolholder
Cutting edge style K Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A16Q-SSKPR09-D200 STEEL 20 16 11 180 32 15 5 -6 0.8 SP**0903... 3
A20R-SSKPR09-D240 STEEL 24 20 13 200 36 18 5 -2 0.8 SP**0903... 3
A25S-SSKPR12-D310 STEEL 31 25 17 250 45 23 5 -2 0.8 SP**1204... 6

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SSKPL** type), and the left hand insert (L) is used for the right
hand toolholders (SSKPR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SSKPR09-D2*0 CSTB-4L060 T-15F
A25S-SSKPR12-D310 CSTB-5S T-20F

Reference pages
A-SSKPR: Inserts → B130 -, CBN → B170

Tungaloy B307
 A /E -STFC R / L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e t r i a n g l e i n s e r t s

øDm h

f
91°

f2

øDs
α° L2 L1

θ°
Int. Toolholder

Cutting edge style F Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

E06-STFCR/L2-D08 CARBIDE 0.500 0.375 0.281 5.000 1.000 0.350 - 0 -9 0.016 TC**21.5... 0.89
E08-STFCR2-D11 CARBIDE 0.688 0.500 0.406 5.000 1.062 0.475 - 0 -6 0.016 TC**21.5... 0.89
E10-STFCR2-D14 CARBIDE 0.875 0.625 0.531 7.000 1.250 0.600 - 0 -5 0.016 TC**21.5... 0.89
E12-STFCR3-D16 CARBIDE 1.000 0.750 0.594 7.000 1.438 0.750 - 0 -5 0.032 TC**32.5... 2.2

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10K-STFCR/L1103-D120 STEEL 12 10 6.5 125 20 9 0.6 0 -13 0.4 TC**1103... 1.2
A12M-STFCR/L1103-D140 STEEL 14 12 7 150 24 11 0.5 0 -10 0.4 TC**1103... 1.2
A16Q-STFCR/L1103-D180 STEEL 18 16 9 180 32 15 0.5 0 -7 0.4 TC**1103... 1.2
E10M-STFCR/L1103-D120 CARBIDE 12 10 6.5 150 25 9 0.7 0 -13 0.4 TC**1103... 1.2
E12Q-STFCR/L1103-D140 CARBIDE 14 12 7 180 27 11 0.5 0 -10 0.4 TC**1103... 1.2
E16R-STFCR/L1103-D180 CARBIDE 18 16 9 200 32 15 0.5 0 -7 0.4 TC**1103... 1.2
*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STFCL** type), and the left hand insert (L) is used for the right
hand toolholders (STFCR** type).

SPARE PARTS
Designation Clamping screw Wrench
E**-STFCR/L2-D... CSTB-2.5 T-8F
E12-STFCR3-D16 CSTB-4S T15-F
A**-STFCR/L1103-D... CSTB-2.5 T-8F
E**-STFCR/L1103-D... CSTB-2.5 T-8F

A -STFC R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e t r i a n g l e i n s e r t s

øDm h
f

91°
f2

øDs

α° L2 L1

θ°
Cutting edge style F Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A06-STFCR/L2 STEEL 0.430 0.375 0.256 6.000 0.625 0.340 - 0 11 0.016 TC**21.5... 0.89
A08-STFCR/L2 STEEL 0.600 0.500 0.312 8.000 0.748 0.460 - 0 9 0.016 TC**21.5... 0.89
A10-STFCR/L2 STEEL 0.770 0.625 0.400 10.000 1.250 0.575 - 0 7 0.016 TC**21.5... 0.89
A12-STFCR/L3 STEEL 0.930 0.750 0.500 10.000 1.870 0.700 - 0 6 0.032 TC**32.5... 2.2

*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STFCL** type), and the left hand insert (L) is used for the right
hand toolholders (STFCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-STFCR/L2 CSTB-2.5 T-8F
A12-STFCR/L3 CSTB-4S T15-F

Reference pages
A/E-STFCR/L: Inserts → B133 -, PCD → B179

B308 www.tungaloyamerica.com
A /E-STFP R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e t r i a n g l e i n s e r t s

øDm h

f
91°

øDs
f2
α° L2 L1
θ°

Int. Toolholder
Cutting edge style F Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

E06-STFPR2-D08 CARBIDE 0.500 0.375 0.281 5.000 1.000 0.350 - 0 -5 0.016 TP**21.5... 0.89
E08-STFPR2-D11 CARBIDE 0.688 0.500 0.406 5.000 1.062 0.475 - 0 -3 0.016 TP**21.5... 0.89
E10-STFPR2-D14 CARBIDE 0.875 0.625 0.531 7.000 1.250 0.605 - 0 -2 0.016 TP**21.5... 0.89
E12-STFPR/L3-D16 CARBIDE 1.000 0.750 0.594 7.000 1.438 0.725 - 0 -2 0.032 TP**32.5... 2.2

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A08H-STFPR/L09-D100 STEEL 10 8 5.5 100 16 7.5 0.7 5 -8 0.4 TP**0902... 0.9
A10K-STFPR/L1102-D120 STEEL 12 10 6.5 125 20 9 0.7 5 -6 0.4 TP**1102... 1.2
A12M-STFPR/L1102-D140 STEEL 14 12 7.0 150 24 11 0.6 5 -4 0.4 TP**1102... 1.2
A16Q-STFPR/L13-D180 STEEL 18 16 9 180 32 15 0.7 5 -2 0.4 TP**1303... 1.4
A20R-STFPR13-D220 STEEL 22 20 11 200 36 18 0.8 5 -2 0.4 TP**1303... 1.4
A25S-STFPR16-D270 STEEL 27 25 13.5 250 45 23 0.6 5 -1 0.4 TP**16T3... 3
E08K-STFPR/L09-D100 CARBIDE 10 8 5.5 125 22 7.5 0.7 5 -8 0.4 TP**0902... 0.9
E10M-STFPR/L1102-D120 CARBIDE 12 10 6.5 150 25 9 0.7 5 -6 0.4 TP**1102... 1.2
E12Q-STFPR/L1102-D140 CARBIDE 14 12 7 180 27 11 0.6 5 -4 0.4 TP**1102... 1.2
E16R-STFPR13-D180 CARBIDE 18 16 9 200 32 15 0.7 5 -2 0.4 TP**1303... 1.4
E20S-STFPR13-D220 CARBIDE 22 20 11 250 36 18 0.8 5 -2 0.4 TP**1303... 1.4

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STFPL ** type), and the left hand insert (L) is used for the right
hand toolholders (STFPR ** type).
(1) Inserts of TPGH, TPGM and TPGA are not applicable.

SPARE PARTS
Designation Clamping screw Wrench
E06-STFPR2-D08 CSTB-2.5B T-8F
E08/10-STFPR2-D... CSTB-2.5 T-8F
E12-STFPR/L3-D16 CSTB-4S T15-F
A08H-STFPR/L09-D100 CSTB-2.2S T-7F
A10K-STFPR/L1102-D120 CSTB-2.5B T-8F
A12M-STFPR/L1102-D140 CSTB-2.5 T-8F
A16Q-STFPR/L13-D180 CSTB-3S T-9F
A20R-STFPR13-D220 CSTB-3 T-9F
A25S-STFPR16-D270 CSTB-4M T-15F
E08K-STFPR/L09-D100 CSTB-2.2S T-7F
E10M-STFPR/L1102-D120 CSTB-2.5B T-8F
E12Q-STFPR/L1102-D140 CSTB-2.5 T-8F
E16R-STFPR13-D180 CSTB-3S T-9F
E20S-STFPR13-D220 CSTB-3 T-9F

Reference pages
A/E-STFPR/L: Inserts → B138 -, CBN → B170 -, PCD → B180

Tungaloy B309
 A /E -STU P R / L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e t r i a n g l e i n s e r t s

øDm h

f
95°

α°

f2

øDs
L2 L1
θ°
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A05-STUPR/L7-D07 STEEL 0.438 0.313 0.250 5.00 0.625 2.880 - 5 -7 0.016 TP**73... 0.66
A06-STUPR/L2-D08 STEEL 0.500 0.375 0.281 5.00 0.750 0.350 - 5 -5 0.016 TP**21.5... 0.89
A08-STUPR/L2-D11 STEEL 0.688 0.500 0.406 5.00 1.000 0.475 - 5 -3 0.016 TP**21.5... 0.89
A10-STUPR/L2-D14 STEEL 0.875 0.625 0.531 7.00 1.250 0.600 - 5 -2 0.016 TP**21.5... 1.0
A10-STUPR/L2.5-D14 STEEL 0.875 0.625 0.531 7.00 1.250 0.600 - 5 -2 0.016 TP**22... 1.0
A12-STUPR/L3-D16 STEEL 1.000 0.750 0.594 7.00 1.437 0.725 - 5 -2 0.032 TP**32.5... 1.0
A16-STUPR/L3-D20 STEEL 1.250 1.000 0.688 7.00 1.750 0.975 - 5 0 0.032 TP**32.5... 2.2
E05-STUPR7-D07 CARBIDE 0.438 0.313 0.250 5.00 0.625 2.880 - 5 -7 0.016 TP**73... 0.66
E06-STUPR2-D08 CARBIDE 0.500 0.375 0.281 5.00 0.750 0.350 - 5 -5 0.016 TP**21.5... 0.89
E08-STUPR2-D11 CARBIDE 0.688 0.500 0.406 5.00 1.000 0.475 - 5 -3 0.016 TP**21.5... 0.89
E10-STUPR2.5-D14 CARBIDE 0.875 0.625 0.531 7.00 1.250 0.600 - 5 -2 0.016 TP**22... 1.0

*Torque: Recommended torque (lbf·ft) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STUPL ** type), and the left hand insert (L) is used for the right
hand toolholders (STUPR ** type).

SPARE PARTS
Designation Clamping screw Wrench
A05-STUPR/L7-D07 CSTB-2.2S T-7F
A06-STUPR/L2-D08 CSTB-2.5S T-8F
A08-STUPR/L2-D11 CSTB-2.5B T-8F
A10-STUPR/L2-D14 CSTB-2.5 T-8F
A10-STUPR/L2.5-D14 CSTB-2.5 T-8F
A12-STUPR/L3-D16 CSTB-4M T-15F
A16-STUPR/L3-D20 CSTB-4M T-15F
E05-STUPR7-D07 CSTB-2.2S T-7F
E06-STUPR2-D08 CSTB-2.5S T-8F
E08-STUPR2-D11 CSTB-2.5B T-8F
E10-STUPR2.5-D14 CSTB-3 T-9F

Reference pages
A/E-STUPR/L: Inserts → B138 -, CBN → B170 -, PCD → B180

B310 www.tungaloyamerica.com
 Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*
A07G-STUPR/L07-D080 STEEL 8 7 4 90 12 6.75 0.4 5 -10 0.4 TP**0701... 0.9
A08H-STUPR/L07-D080 STEEL 8 8 4 100 19.5 7.5 0.5 5 -10 0.4 TP**0701... 0.9
A08H-STUPR/L09-D100 STEEL 10 8 5.5 100 16 7.5 0.6 5 -8 0.4 TP**0902...(1) 0.9
A10F-STUPR1102-D120 STEEL 12 10 6.5 80 20 9 1.4 5 -6 0.4 TP**1102...(1) 1.2
A10K-STUPR/L1102-D120 STEEL 12 10 6.5 125 20 9 0.7 5 -6 0.4 TP**1102...(1) 1.2
A10K-STUPR/L1103-D120 STEEL 12 10 6.5 125 20 9 0.6 5 -10 0.4 TP**1103...(1) 1.4
A12H-STUPR1102-D140 STEEL 14 12 7 100 24 11 0.9 5 -4 0.4 TP**1102...(1) 1.2
A12M-STUPR/L1102-D140 STEEL 14 12 7 150 24 11 0.7 5 -4 0.4 TP**1102...(1) 1.2
A12M-STUPR/L1103-D140 STEEL 14 12 7 150 24 11 0.6 5 -6 0.4 TP**1103...(1) 1.4
A12H-STUPR1102-D160 STEEL 16 12 9 100 24 11 0.6 5 -3 0.4 TP**1102...(1) 1.2

Int. Toolholder
A12M-STUPR/L1102-D160 STEEL 16 12 9 150 24 11 0.6 5 -3 0.4 TP**1102...(1) 1.2
A16K-STUPR13-D180 STEEL 18 16 9 125 32 15 0.9 5 -3 0.4 TP**1303...(1) 1.4
A16Q-STUPR/L1103-D180 STEEL 18 16 9 180 32 15 0.8 5 -4 0.4 TP**1103...(1) 1.4
A16Q-STUPR/L13-D180 STEEL 18 16 9 180 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
A16K-STUPR13-D200 STEEL 20 16 11 125 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
A16Q-STUPR/L13-D200 STEEL 20 16 11 180 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
A20R-STUPR/L1103-D220 STEEL 22 20 11 200 36 18 0.7 5 -2 0.4 TP**1103...(1) 1.4
A20R-STUPR/L13-D220 STEEL 22 20 11 200 36 18 0.7 5 -2 0.4 TP**1303...(1) 1.4
A25S-STUPR/L16-D270 STEEL 27 25 13.5 250 45 23 0.5 5 -1 0.8 TP**16T3...(1) 3
A32T-STUPR/L16-D340 STEEL 34 32 17 300 50 30 0.7 5 0 0.8 TP**16T3... 3
E07H-STUPR/L07-D080 CARBIDE 8 7 4 100 14 6.75 0.3 5 -10 0.4 TP**0701... 0.9
E08G-STUPR07-D080 CARBIDE 8 8 4 90 44.5 7.5 0.5 5 -10 0.4 TP**0701... 0.9
E08K-STUPR/L07-D080 CARBIDE 8 8 4 125 44.5 7.5 0.5 5 -10 0.4 TP**0701... 0.9
E08G-STUPR09-D100 CARBIDE 10 8 5.5 90 22 7 0.6 5 -8 0.4 TP**0902...(1) 0.9
E08K-STUPR/L09-D100 CARBIDE 10 8 5.5 125 22 7 0.6 5 -8 0.4 TP**0902...(1) 0.9
E10F-STUPR1102-D120 CARBIDE 12 10 6.5 80 25 9 0.5 5 -6 0.4 TP**1102...(1) 1.2
E10H-STUPR1102-D120 CARBIDE 12 10 6.5 100 25 9 0.6 5 -6 0.4 TP**1102...(1) 1.2
E10M-STUPR/L1102-D120 CARBIDE 12 10 6.5 150 25 9 0.6 5 -6 0.4 TP**1102...(1) 1.2
E10M-STUPR/L1103-D120 CARBIDE 12 10 6.5 150 25 9 0.7 5 -10 0.4 TP**1103...(1) 1.4
E12G-STUPR1102-D140 CARBIDE 14 12 7 90 27 11 0.9 5 -4 0.4 TP**1102...(1) 1.2
E12J-STUPR1102-D140 CARBIDE 14 12 7 110 27 11 0.6 5 -4 0.4 TP**1102...(1) 1.2
E12Q-STUPR/L1102-D140 CARBIDE 14 12 7 180 27 11 0.6 5 -4 0.4 TP**1102...(1) 1.2
E12Q-STUPR/L1103-D140 CARBIDE 14 12 7 180 27 11 0.7 5 -6 0.4 TP**1103...(1) 1.4
E12G-STUPR1102-D160 CARBIDE 16 12 9 90 27 11 0.6 5 -3 0.4 TP**1102...(1) 1.2
E12J-STUPR1102-D160 CARBIDE 16 12 9 110 27 11 0.6 5 -3 0.4 TP**1102...(1) 1.2
E12Q-STUPR/L1102-D160 CARBIDE 16 12 9 180 27 11 0.6 5 -3 0.4 TP**1102...(1) 1.2
E16H-STUPR13-D180 CARBIDE 18 16 9 100 32 15 0.9 5 -3 0.4 TP**1303...(1) 1.4
E16R-STUPR/L1103-D180 CARBIDE 18 16 9 200 32 15 0.8 5 -3 0.4 TP**1103...(1) 1.4
E16L-STUPR13-D180 CARBIDE 18 16 9 130 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
E16R-STUPR/L13-D180 CARBIDE 18 16 9 200 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
E16H-STUPR13-D200 CARBIDE 20 16 11 100 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
E16L-STUPR13-D200 CARBIDE 20 16 11 130 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
E16R-STUPL13-D200 CARBIDE 20 16 11 200 32 15 0.6 5 -3 0.4 TP**1303...(1) 1.4
E20S-STUPR1103-D220 CARBIDE 22 20 11 250 36 18 0.7 5 -2 0.4 TP**1103...(1) 1.4
E20S-STUPR13-D220 CARBIDE 22 20 11 250 36 18 0.6 5 -2 0.4 TP**1303...(1) 1.4
E25T-STUPR16-D270 CARBIDE 27 25 13.5 300 45 23 0.5 5 -1 0.8 TP**16T3... 3
*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STUPL ** type), and the left hand insert (L) is used for the right
hand toolholders (STUPR ** type).
(1) Inserts of TPGH, TPGM and TPGA are not applicable.

SPARE PARTS
Designation Clamping screw Wrench
A07/08-STUPR/L07/09-D... CSTB-2.2L038 T-7F
A10*-STUPR/L1102-D120 CSTB-2.5S T-8F
A12*-STUPR/L1102-D... CSTB-2.5B T-8F
A12M-STUPR/L1103-D140 CSTB-3L050 T-9F
A16*-STUPR/L13-D... CSTB-3S T-9F
A20R-STUPR/L13-D220 CSTB-3 T-9F
A**-STUPR/L16-D... CSTB-4M T-15F
E07/08-STUPR/L07/09-D... CSTB-2.2L038 T-7F
E10*-STUPR/L1102-D120 CSTB-2.5S T-8F
E12*-STUPR/L1102-D... CSTB-2.5B T-8F
E**-STUPR/L1103-D... CSTB-3L050 T-9F
E16*-STUPR/L13-D... CSTB-3S T-9F
E20S-STUPR13-D220 CSTB-3 T-9F
E25T-STUPR16-D270 CSTB-4M T-15F

Reference pages
A/E-STUPR/L: Inserts → B138 -, CBN → B170 -, PCD → B180

Tungaloy B311
 A/E-S W U B R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e t r i g o n i n s e r t s

øDs
øDm h
93°

f
L2

f
α° L1 L1

øDs
θ° Straight shank
style
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h θ° α° rε** Insert Torque*

A05F-SWUBR/L03-D060 STEEL 6 5 3 80 9 4.8 0 -13 0.4 WB**0301... 0.6
A06G-SWUBR/L03-D070 STEEL 7 6 3.5 90 11 5.75 0 -12 0.4 WB**0301... 0.6
A07G-SWUBR/L03-D080 STEEL 8 7 4 90 12 6.75 0 -11 0.4 WB**0301... 0.6
A08H-SWUBR03-D060 STEEL 6 8 3.1 100 18 7.5 0 -12 0.4 WB**0301... 0.6
A08H-SWUBR03-D070 STEEL 7 8 3.6 100 20 7.5 0 -12 0.4 WB**0301... 0.6
E05G-SWUBR/L03-D060 CARBIDE 6 5 3 90 10 4.8 0 -13 0.4 WB**0301... 0.6
E06H-SWUBR/L03-D070 CARBIDE 7 6 3.5 100 12 5.75 0 -12 0.4 WB**0301... 0.6
E07H-SWUBR/L03-D080 CARBIDE 8 7 4 100 14 6.75 0 -11 0.4 WB**0301... 0.6
E08K-SWUBR03-D060 CARBIDE 6 8 3.1 125 30 7.5 0 -12 0.4 WB**0301... 0.6
E08K-SWUBR03-D070 CARBIDE 7 8 3.6 125 40 7.5 0 -12 0.4 WB**0301... 0.6

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SWUBL** type), and the left hand insert (L) is used for the right
hand toolholders (SWUBR** type).

SPARE PARTS
Designation Clamping screw Wrench
A/E**-SWUBR/L... CSTB-2 T-6F

Reference pages
A/E-SWUBR/L: Inserts → B153

B312 www.tungaloyamerica.com
A/E -SD U C R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h
93°

f
30˚

f2
α°

øDs
L2 L1

θ°

Int. Toolholder
Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A06-SDUCR2-D10 STEEL 0.625 0.375 0.406 5.000 0.750 0.350 0.218 0 -8 0.016 DC**21.5... 0.89
A08-SDUCR/L2-D11 STEEL 0.688 0.500 0.406 5.000 1.000 0.475 0.156 0 -6 0.016 DC**21.5... 0.89
A10-SDUCR2-D14 STEEL 0.875 0.625 0.531 7.000 1.250 0.600 0.218 0 -4 0.016 DC**21.5... 0.89
A12-SDUCR/L3-D16 STEEL 1.000 0.750 0.594 10.000 1.500 0.700 0.218 0 -2 0.032 DC**32.5... 2.2
E06-SDUCR2-D10 CARBIDE 0.625 0.375 0.406 5.000 1.000 0.375 0.218 0 -7 0.016 DC**21.5... 0.89
E08-SDUCR2-D11 CARBIDE 0.688 0.500 0.406 5.000 1.062 0.475 0.156 0 -6 0.016 DC**21.5... 0.89
E10-SDUCR2-D14 CARBIDE 0.875 0.625 0.531 7.000 1.250 0.600 0.218 0 -4 0.016 DC**21.5... 0.89
E12-SDUCR/L3-D16 CARBIDE 1.000 0.750 0.594 7.000 1.438 0.750 0.218 0 -5 0.032 DC**32.5... 2.2

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10K-SDUCR/L07-D130 STEEL 13 10 7 125 20 9 2 0 -10 0.4 DC**0702... 1.2
A12M-SDUCR/L07-D160 STEEL 16 12 9.3 150 24 11 3.3 0 -6 0.4 DC**0702... 1.2
A16Q-SDUCR/L07-D200 STEEL 20 16 11.3 180 32 15 3.3 0 -5 0.4 DC**0702... 1.2
A20R-SDUCR/L11-D270 STEEL 27 20 16.1 200 36 18 6.1 0 -5 0.8 DC**11T3... 3
A25S-SDUCR/L11-D320 STEEL 32 25 18.6 250 45 23 6.1 0 -4 0.8 DC**11T3... 3
E10H-SDUCR07-D130 CARBIDE 13 10 7 100 25 9 1.9 5 -3.5 0.4 DC**0702... 1.2
E10M-SDUCR/L07-D130 CARBIDE 13 10 7 150 25 9 2 0 -10 0.4 DC**0702... 1.2
E12J-SDUCR07-D160 CARBIDE 16 12 9.3 110 27 11 3.2 0 -6 0.4 DC**0702... 1.2
E12Q-SDUCR/L07-D160 CARBIDE 16 12 9.3 180 27 11 3.3 0 -6 0.4 DC**0702... 1.2
E16L-SDUCR07-D200 CARBIDE 20 16 11.3 130 32 15 3.2 0 -5 0.4 DC**0702... 1.2
E16R-SDUCR/L07-D200 CARBIDE 20 16 11.3 200 32 15 3.3 0 -5 0.4 DC**0702... 1.2
E20S-SDUCR11-D270 CARBIDE 27 20 16.1 250 36 18 6.1 0 -5 0.8 DC**11T3... 3

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SDUCL** type), and the left hand insert (L) is used for the right
hand toolholders (SDUCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A06-SDUCR2-D10 CSTB-2.5 T-8F
A08-SDUCR/L2-D11 CSTB-2.5B T-8F
A10-SDUCR2-D14 CSTB-2.5 T-8F
A12-SDUCR/L3-D16 CSTB-3.5 T-15F
E06-SDUCR2-D10 CSTB-2.5 T-8F
E08-SDUCR2-D11 CSTB-2.5B T-8F
E10-SDUCR2-D14 CSTB-2.5 T-8F
E12-SDUCR/L3-D16 CSTB-4S T15-F
A1**-SDUCR/L07-D1*0 CSTB-2.5S T-8F
A16Q-SDUCR/L07-D200 CSTB-2.5 T-8F
A2**-SDUCR/L11-D**0 CSTB-4S T-15F
E1**-SDUCR/L07-D1*0 CSTB-2.5S T-8F
E16*-SDUCR/L07-D200 CSTB-2.5 T-8F
E20S-SDUCR11-D270 CSTB-4S T-15F

Reference pages
A/E-SDUCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B313
 A /E -SV U B R / L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDs
øDm h
L2
93°
50˚

f2

f2
L1

øDs
α° L1
θ° Carbide shank
style
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A12-SVUBR2-D16 STEEL 1.000 0.750 0.594 10.000 1.425 0.725 0.218 -0 -6 0.016 VB**22... 0.89

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16Q-SVUBR/L11-D200 STEEL 20 16 15.5 180 35 15 8 0 -8 0.4 VB**1103... 1.2
A20R-SVUBR/L11-D250 STEEL 25 20 17.5 200 40 19 8 0 -7 0.4 VB**1103... 1.2
A25S-SVUBR/L16-D320 STEEL 32 25 20.5 250 50 23 8.5 0 -6 0.8 VB**1604... 3
E16R-SVUBR/L11-D245 CARBIDE 24.5 16 16 200 - 15 8 0 -8 0.4 VB**1103... 1.2
E20S-SVUBR/L11-D285 CARBIDE 28.5 20 18 250 - 19 8 0 -7 0.4 VB**1103... 1.2
E25T-SVUBR/L16-D340 CARBIDE 34 25 21 300 - 23 8.5 0 -6 0.8 VB**1604... 3

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVUBL** type), and the left hand insert (L) is used for the right
hand toolholders (SVUBR** type).

SPARE PARTS
Designation Clamping screw Wrench
A12-SVUBR2-D16 CSTB-2.5 T-8F
A**-SVUBR/L11-D2*0 CSTB-2.5 T-8F
A25S-SVUBR/L16-D320 CSTB-3.5 T-15F
E**-SVUBR/L11-D2*5 CSTB-2.5 T-8F
E25T-SVUBR/L16-D340 CSTB-3.5 T-15F

Reference pages
A/E-SVUBR/L: Inserts → B147 -, CBN → B171 -

B314 www.tungaloyamerica.com
A /E-S VU C R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDs
øDm h
L2
93°
50˚

f2

f2
øDs
L1
α° L1
θ° Carbide shank
style

Int. Toolholder
Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10-SVUCR6-D14 STEEL 0.875 0.625 0.531 7.000 1.250 0.600 0.218 0 -5 0.016 VC**63... 0.44
A12-SVUCR2-D16 STEEL 1.000 0.750 0.594 10.000 1.420 0.725 0.218 0 -5 0.016 VC**22... 1.0

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A12M-SVUCR/L08-D160 STEEL 16 12 11 150 30 11 5.5 0 -8 0.4 VC**0802... 0.6
A25S-SVUCR/L16-D320 STEEL 32 25 19 250 45 23 6.5 0 -5 0.8 VC**1604... 3
E12Q-SVUCR/L08-D180 CARBIDE 18 12 11.5 180 - 11 5.5 0 -8 0.4 VC**0802... 0.6
E25T-SVUCR/L16-D320 CARBIDE 32 25 19 300 - 23 6.5 0 -5 0.8 VC**1604... 3
*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVUCL** type), and the left hand insert (L) is used for the right
hand toolholders (SVUCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A10-SVUCR6-D14 CSTB-2L T-6F
A12-SVUCR2-D16 CSTB-2.5 T-8F
A12M-SVUCR/L08-D160 CSTB-2L T-6F
A25S-SVUCR/L16-D320 CSTB-3.5 T-15F
E12Q-SVUCR/L08-D180 CSTB-2L T-6F
E25T-SVUCR/L16-D320 CSTB-3.5 T-15F

Reference pages
A/E-SVUCR/L: Inserts → B149 -, CBN → B171 -, PCD → B179 -

Tungaloy B315
 A /E -SD QC R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h

f
107.5°
15.5˚

f2
α°

øDs
L2 L1

θ°
Int. Toolholder

Cutting edge style Q Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A06-SDQCR2-D10 STEEL 0.625 0.375 0.406 5.000 0.750 0.350 - 0 -7 0.016 DC**21.5... 0.89
A08-SDQCR2-D11 STEEL 0.688 0.500 0.406 5.000 1.000 0.475 - 0 -6 0.016 DC**21.5... 0.89
A10-SDQCR2-D14 STEEL 0.875 0.625 0.531 7.000 1.250 0.600 - 0 -4 0.016 DC**21.5... 0.89

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10K-SDQCR/L07-D130 STEEL 13 10 7.6 125 20 9 2.6 0 -8 0.4 DC**0702... 1.2
A12M-SDQCR/L07-D160 STEEL 16 12 8.6 150 24 11 2.6 0 -6 0.4 DC**0702... 1.2
A16Q-SDQCR/L07-D200 STEEL 20 16 10.6 180 32 15 2.6 0 -5 0.4 DC**0702... 1.2
A20R-SDQCR/L11-D250 STEEL 25 20 13.7 200 36 18 3.7 0 -7 0.8 DC**11T3... 3
A25S-SDQCR/L11-D300 STEEL 30 25 16.2 250 45 23 3.7 0 -4 0.8 DC**11T3... 3
E10H-SDQCR07-D130 CARBIDE 13 10 7.6 100 25 9 2.5 0 -8 0.4 DC**0702... 1.2
E10M-SDQCR/L07-D130 CARBIDE 13 10 7.6 150 25 9 2.6 0 -8 0.4 DC**0702... 1.2
E12J-SDQCR07-D160 CARBIDE 16 12 8.6 110 27 11 2.5 0 -6 0.4 DC**0702... 1.2
E12Q-SDQCR/L07-D160 CARBIDE 16 12 8.6 180 27 11 2.6 0 -6 0.4 DC**0702... 1.2
E16L-SDQCR07-D200 CARBIDE 20 16 10.6 130 32 15 2.5 0 -5 0.4 DC**0702... 1.2
E16R-SDQCR/L07-D200 CARBIDE 20 16 10.6 200 32 15 2.6 0 -5 0.4 DC**0702... 1.2
E20S-SDQCR/L11-D250 CARBIDE 25 20 13.7 250 36 18 3.7 0 -7 0.8 DC**11T3... 3

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SDQCL** type), and the left hand insert (L) is used for the right
hand toolholders (SDQCR** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SDQCR2-D... CSTB-2.5B T-8F
A1**-SDQCR/L07-D**0 CSTB-2.5S T-8F
A2**-SDQCR/L11-D**0 CSTB-4S T-15F
E1**-SDQCR/L07-D**0 CSTB-2.5S T-8F
E20S-SDQCR/L11-D250 CSTB-4S T-15F

Reference pages
A/E-SDQCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

B316 www.tungaloyamerica.com
A/E -SV Q B R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h

117.5°

f
25.5˚

f2

øDs
α° L2 L1
θ°

Int. Toolholder
Cutting edge style Q Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10-SVQBR2-D16 STEEL 1.000 0.625 0.500 7.000 1.250 0.600 0.188 -5 -6 0.016 VB**22... 0.89

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A12M-SVQBR/L11-D170 STEEL 17 12 10.5 150 24 11 4.5 -5 -10 0.4 VB**1103... 1.2
A16Q-SVQBR/L11-D215 STEEL 21.5 16 13 180 30 15 5 -5 -8 0.4 VB**1103... 1.2
A20R-SVQBR/L11-D255 STEEL 25.5 20 15 200 36 18 5 -5 -6 0.4 VB**1103... 1.2
A25S-SVQBR/L16-D305 STEEL 30.5 25 17.5 250 45 23 5 -5 -8 0.8 VB**1604... 3
E12Q-SVQBR/L11-D170 CARBIDE 17 12 10.5 180 27 11 4.5 -5 -10 0.4 VB**1103... 1.2
E16R-SVQBR/L11-D215 CARBIDE 21.5 16 13 200 32 15 5 -5 -8 0.4 VB**1103... 1.2
E20S-SVQBR/L11-D255 CARBIDE 25.5 20 15 250 36 18 5 -5 -6 0.4 VB**1103... 1.2
E25T-SVQBR/L16-D305 CARBIDE 30.5 25 17.5 300 45 23 5 -5 -8 0.8 VB**1604... 3

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVQBL type), and the left hand insert (L) is used for the right
hand toolholders (SVQBR type).

SPARE PARTS
Designation Clamping screw Wrench
A10-SVQBR2-D16 CSTB-2.5 T-8F
A**-SVQBR/L11-D... CSTB-2.5 T-8F
A25S-SVQBR/L16-D305 CSTB-3.5 T-15F
E**-SVQBR/L11-D... CSTB-2.5 T-8F
E25T-SVQBR/L16-D305 CSTB-3.5 T-15F

Reference pages
A/E-SVQBR/L: Inserts → B147 -, CBN → B171 -

Tungaloy B317
 A /E -SV Q C R / L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h

117.5°

f
25.5˚

f2

øDs
α° L2 L1
θ°
Int. Toolholder

Cutting edge style Q Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A08-SVQCR6-D11 STEEL 0.688 0.500 0.375 5.000 1.000 0.475 0.125 -5 -6 0.016 VC**63... 0.44
A10-SVQCR2-D16 STEEL 1.000 0.625 0.500 10.000 1.250 0.600 0.188 -5 -4 0.016 VC**22... 0.89

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A10K-SVQCR/L08-D135 STEEL 13.5 10 8 125 20 9 3 -5 -8 0.4 VC**0802... 0.6
A16Q-SVQCR/L11-D215 STEEL 21.5 16 13 180 30 15 4.9 -5 -8 0.4 VC**1103... 1.2
E10M-SVQCR/L08-D135 CARBIDE 13.5 10 8 150 25 9 3 -5 -8 0.4 VC**0802... 0.6
E16R-SVQCR/L11-D215 CARBIDE 21.5 16 13 200 32 15 4.9 -5 -8 0.4 VC**1103... 1.2

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVQCL ** type), and the left hand insert (L) is used for the right
hand toolholders (SVQCR ** type).

SPARE PARTS
Designation Clamping screw Wrench
A08-SVQCR6-D11 CSTB-2L T-6F
A10-SVQCR2-D16 CSTB-2.5 T-8F
A10K-SVQCR/L08-D135 CSTB-2L T-6F
A16Q-SVQCR/L11-D215 CSTB-2.5 T-8F
E10M-SVQCR/L08-D135 CSTB-2L T-6F
E16R-SVQCR/L11-D215 CSTB-2.5 T-8F

Reference pages
A/E-SVQCR/L: Inserts → B149 -

B318 www.tungaloyamerica.com
A /E-S DZ C R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

øDm L2 h
93°

øDs
f
30˚

f
f2
L3 L1
α°

f2
L1
L3
θ° Carbide shank
style

Int. Toolholder
Cutting edge style Z Right hand (R) shown.

Inch Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A10-SDZCR2-D14 STEEL 0.875 0.625 0.531 7.000 1.250 - 0.600 0.218 - - 0.016 DC**21.5... 0.89

Metric Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A12M-SDZCR/L07-D140 STEEL 14 12 10.5 150 30 12.5 11 4.5 0 -9 0.4 DC**0702... 1.2
A16Q-SDZCR/L07-D160 STEEL 16 16 12.5 180 35 12.5 15 4.5 0 -8 0.4 DC**0702... 1.2
A20R-SDZCR/L11-D200 STEEL 20 20 15.5 200 40 15.0 18 5.5 0 -8 0.8 DC**11T3... 3
A25S-SDZCR/L11-D250 STEEL 25 25 18 250 50 15 23 5.5 0 -6 0.8 DC**11T3... 3
E12Q-SDZCR/L07-D180 CARBIDE 18 12 10.5 180 - 12.5 11 4.5 0 -8 0.4 DC**0702... 1.2
E16R-SDZCR/L07-D220 CARBIDE 22 16 12.5 200 - 12.5 15 4.5 0 -6 0.4 DC**0702... 1.2

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the right hand toolholders (SDZCR ** type), and the left hand insert (L) is used for the left
hand toolholders (SDZCL ** type).

SPARE PARTS
Designation Clamping screw Wrench
A10-SDZCR2-D14 CSTB-2.5 T-8F
A1**-SDZCR/L07-D1*0 CSTB-2.5 T-8F
A2**-SDZCR/L11-D2*0 CSTB-4S T-15F
E1**-SDZCR/L07-D**0 CSTB-2.5 T-8F

Reference pages
A/E-SDZCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B319
 A -SV Z B R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm L2 h
93°

f2
50˚

øDs
L3 L1
α°
θ°
Int. Toolholder

Cutting edge style Z Right hand (R) shown.

Inch Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A12-SVZBR2-D16 STEEL 1.000 0.750 0.594 10.000 1.430 - 0.725 0.218 0 -5 0.016 VB**22... 0.89

Metric Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A16Q-SVZBR/L11-D200 STEEL 20 16 15.5 180 35 12.5 15 8 0 -8 0.4 VB**1103... 1.2
A20R-SVZBR/L11-D250 STEEL 25 20 17.5 200 40 12.5 18 8 0 -7 0.4 VB**1103... 1.2
A25S-SVZBR/L16-D320 STEEL 32 25 24 250 50 17.5 23 12 0 -6 0.8 VB**1604... 3
A32T-SVZBR/L16-D400 STEEL 40 32 27.5 300 72 17.5 30 12 0 -5 0.8 VB**1604... 3

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the right hand toolholders (SVZBR type), and the left hand insert (L) is used for the left
hand toolholders (SVZBL type).

SPARE PARTS
Designation Clamping screw Wrench
A12-SVZBR2-D16 CSTB-2.5 T-8F
A**-SVZBR/L11-D** CSTB-2.5 T-8F
A25S-SVZBR/L16-D320 CSTB-3.5 T-15F
A32T-SVZBR/L16-D400 CSTB-3.5L T-15F

A -SV Z C R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm L2 h
93°
f

f2

50˚
øDs

L3 L1
α°
θ°
Right hand (R) shown.
Cutting edge style Z
Inch Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*
A08-SVZCR6-D12 STEEL 0.750 0.500 0.438 5.000 1.000 - 0.475 0.188 0 -6 0.016 VC**63... 0.44
A12-SVZCR2-D16 STEEL 1.000 0.750 0.593 10.000 1.425 - 0.725 0.218 0 -7 0.016 VC**22... 0.89

Metric Material øDm øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

A12M-SVZCR/L08-D160 STEEL 16 12 11 150 30 10 11 5.5 0 -8 0.4 VC**0802... 0.6

*Torque: Recommended torque (Ibf∙ft, N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the right hand toolholders (SVZCR ** type), and the left hand insert (L) is used for the left
hand toolholders (SVZCL ** type).

SPARE PARTS
Designation Clamping screw Wrench
A08-SVZCR6-D12 CSTB-2L T-6F
A12-SVZCR2-D16 CSTB-2.5 T-8F
A12M-SVZCR/L08-D160 CSTB-2L T-6F

Reference pages
A-SVZBR/L: Inserts → B147 -, CBN → B171 -
A-SVZCR/L: Inserts → B149 -

B320 www.tungaloyamerica.com
A /E-S E Z PR /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 7 5 ° r h o m b i c i n s e r t s

øDm h
95°

f
L2

øDs
f2
α° L1

θ°
Cutting edge style Z Right hand (R) shown.

Int. Toolholder
Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*
A04F-SEZPR/L03-D055 STEEL 5.5 4 3.2 80 4 3.8 1.2 0 -8 0.2 EP**03X1... 0.6
A05F-SEZPR/L03-D065 STEEL 6.5 5 3.7 80 5 4.8 1.2 0 -6 0.2 EP**03X1... 0.6
E04G-SEZPR/L03-D055 CARBIDE 5.5 4 3.2 90 5 3.8 1.2 0 -8 0.2 EP**03X1... 0.6
E05G-SEZPR/L03-D065 CARBIDE 6.5 5 3.7 90 6 4.8 1.2 0 -6 0.2 EP**03X1... 0.6

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the right hand toolholders (SEZPR ** type), and the left hand insert (L) is used for the left
hand toolholders (SEZPL ** type).

SPARE PARTS
Designation Clamping screw Wrench
A**-SEZPR/L03-D... CSTA-1.6 T-6F
E**-SEZPR/L03-D... CSTA-1.6 T-6F

A -PC LN R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDm h
95°
f

f2

L2

øDs
α° L1
95°
θ°
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16M-PCLNR/L09-D200 STEEL 20 16 11 150 32 15 3 -6 -14 0.8 CN**0903... 1.7
A20Q-PCLNR/L09-D250 STEEL 25 20 13 180 36 18 3 -6 -12 0.8 CN**0903... 1.7
A25R-PCLNR/L09-D320 STEEL 32 25 17 200 45 23 4.5 -6 -11 0.8 CN**0903... 1.7
A25R-PCLNR/L12-D320 STEEL 32 25 17 200 45 23 4.5 -6 -13 0.8 CN**1204... 2.7
A32S-PCLNR/L12-D400 STEEL 40 32 22 250 50 30 6 -6 -11 0.8 CN**1204... 4.8
A40T-PCLNR/L12-D500 STEEL 50 40 27 300 60 37 7 -6 -10 0.8 CN**1204... 4.8
A50U-PCLNR/L12-D630 STEEL 63 50 35 350 65 47 10 -6 -8 0.8 CN**1204... 4.8

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (PCLNL ** type), and the left hand insert (L) is used for the right
hand toolholders (PCLNR ** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
(Optional parts) (Optional parts)
A**-PCLNR/L09-D**0 - LCS22A - P-2F - - LCL32N (EA-25) (SSHM5-6)
A25R-PCLNR/L12-D320 - LCS43 - - P-2.5 - LCL43N (EA-32) (SSHM5-6)
A32S-PCLNR12-D400 LSC42BR - LCS4 - P-3 LSP4 LCL4 (EA-32) (SSHM5-6)
A32S-PCLNL12-D400 LSC42BL - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A40T-PCLNR12-D500 LSC42BR - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A40T-PCLNL12-D500 LSC42BL - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A50U-PCLNR12-D630 LSC42BR - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A50U-PCLNL12-D630 LSC42BL - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)

Reference pages
A/E-SEZPR/L: Inserts → B124 -, CBN → B173
A-PCLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178

Tungaloy B321
 A -P W LN R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e t r i g o n i n s e r t s

øDm h
95°

f
L2

øDs
f2
α° L1
95°
θ°
Int. Toolholder

Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16M-PWLNR/L06-D200 STEEL 20 16 11 150 32 15 3 -8 -17 0.8 WN**0604... 1.7
A20Q-PWLNR/L06-D250 STEEL 25 20 13 180 36 18 3 -6 -14 0.8 WN**0604... 1.7
A25R-PWLNR/L06-D320 STEEL 32 25 17 200 45 23 4.5 -6 -12 0.8 WN**0604... 2.7
A32S-PWLNR/L06-D400 STEEL 40 32 22 250 50 30 6 -6 -11 0.8 WN**0604... 2.7
A25R-PWLNR/L08-D320 STEEL 32 25 17 200 45 23 4.5 -6 -13 0.8 WN**0804... 2.7
A32S-PWLNR/L08-D400 STEEL 40 32 22 250 50 30 6 -6 -11 0.8 WN**0804... 4.8
A40T-PWLNR/L08-D500 STEEL 50 40 27 300 60 37 7 -6 -10 0.8 WN**0804... 4.8

*Torque: Recommended torque (N·m) for clamping

**rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
(Optional parts) (Optional parts)
A16M-PWLNR/L06-D200 - LCS33 - P-2F - - LCL33N - (SSHM3-4)
A20Q-PWLNR/L06-D250 - LCS33 - P-2F - - LCL33N (EA-20) (SSHM3-4)
A25R-PWLNR/L06-D320 LSW312BR/L - LCS3B - P-2.5 LSP3 LCL3 (EA-25) (SSHM4-5)
A32S-PWLNR/L06-D400 LSW312BR/L - LCS3 - P-2.5 LSP3 LCL3 (EA-32) (SSHM4-5)
A25R-PWLNR/L08-D320 - LCS43 - - P-2.5 - LCL43N (EA-25) (SSHM4-5)
A32S-PWLNR/L08-D400 LSW42BR/L - LCS4 - P-3 LSP4 LCL4 (EA-32) (SSHM4-5)
A40T-PWLNR/L08-D500 LSW42BR/L - LCS4 - P-3 LSP4 LCL4 - (SSHM4-5)

A -P S K N R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e s q u a re i n s e r t s

øDm h

75°
f

L2
f2

øDs

L1
α°
θ°
Cutting edge style K Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A32S-PSKNR/L12-D400 STEEL 40 32 22 250 50 30 6 -6 -10 0.8 SN**1204... 4.8
A40T-PSKNR/L12-D500 STEEL 50 40 27 300 60 37 7 -6 -10 0.8 SN**1204... 4.8
A50U-PSKNR/L12-D630 STEEL 63 50 35 350 65 47 10 -6 -8 0.8 SN**1204... 4.8

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (PSKNL ** type), and the left hand insert (L) is used for the right
hand toolholders (PSKNR ** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw Wrench Spring Lever
(Optional parts) (Optional parts)
A32S-PSKNR/L12-D400 LSS42BR/L LCS4 P-3 LSP4 LCL4 (EA-32) (SSHM4-5)
A40T-PSKNR/L12-D500 LSS42BR/L LCS4 P-3 LSP4 LCL4 - (SSHM6-6)
A50U-PSKNR/L12-D630 LSS42BR/L LCS4 P-3 LSP4 LCL4 - (SSHM6-6)

Reference pages
A-PWLNR/L: Inserts → B097 -, CBN → B167
A-PSKNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178

B322 www.tungaloyamerica.com
A -PTFN R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h

øDs
91°

f
L2

f2
L1
α°
θ°

Int. Toolholder
Cutting edge style F Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A25R-PTFNR/L16-D320 STEEL 32 25 17 200 45 23 1.2 -6 -12 0.8 TN**1604... 2.7
A32S-PTFNR/L16-D400 STEEL 40 32 22 250 50 30 1.1 -6 -10 0.8 TN**1604... 2.7
A40T-PTFNR/L16-D500 STEEL 50 40 27 300 60 37 1.1 -6 -10 0.8 TN**1604... 2.7
A50U-PTFNR/L16-D630 STEEL 63 50 35 350 65 47 1.1 -6 -8 0.8 TN**1604... 2.7

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (PTFNL ** type), and the left hand insert (L) is used for the right
hand toolholders (PTFNR ** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw Wrench Spring Lever
(Optional parts) (Optional parts)
A25R-PTFNR/L16-D320 ELST317BR/L LCS3 P-2.5 LSP3 LCL33 (EA-25) (SSHM4-5)
A32S-PTFNR/L16-D400 LST317BR/L LCS3 P-2.5 LSP3 LCL3 (EA-32) (SSHM4-5)
A40T-PTFNR/L16-D500 LST317BR/L LCS3 P-2.5 LSP3 LCL3 - (SSHM6-6)
A50U-PTFNR/L16-D630 LST317BR/L LCS3 P-2.5 LSP3 LCL3 - (SSHM6-6)

Reference pages
A-PTFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B323
 A -P D U N R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h

øDs
93°

f
L2

f2
α° L1
θ°
Cutting edge style U Right hand (R) shown.
Int. Toolholder

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A20Q-PDUNR/L11-D250 STEEL 25 20 13 180 36 18 3 -6 -14 0.8 DN**1104... 1.7
A25R-PDUNR/L11-D320 STEEL 32 25 17 200 45 23 4.5 -6 -12 0.8 DN**1104... 2.7
A32S-PDUNR/L15-D400 STEEL 40 32 22 250 50 30 6 -6 -13 0.8 DN**1504... 4.8
A40T-PDUNR/L15-D500 STEEL 50 40 27 300 60 37 7 -6 -10 0.8 DN**1504... 4.8
A50U-PDUNR/L15-D630 STEEL 63 50 35 350 65 47 10 -6 -8 0.8 DN**1504... 4.8
A32S-PDUNR/L1506-D400 STEEL 40 32 22 250 50 30 6 -6 -13 0.8 DN**1506... 4.8
A40T-PDUNR/L1506-D500 STEEL 50 40 27 300 60 37 7 -6 -11 0.8 DN**1506... 4.8
A50U-PDUNR/L1506-D630 STEEL 63 50 35 350 65 47 10 -6 -10 0.8 DN**1506... 4.8
*Torque: Recommended torque (N·m) for clamping
**rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
(Optional parts) (Optional parts)
A20Q-PDUNR/L11-D250 - LCS22A - P-2F - - LCL33NL (EA-20) (SSHM2.5-3)
A25R-PDUNR/L11-D320 ELSD317BR/L - LCS3 - P-2.5 LSP3 LCL33L (EA-25) (SSHM3-4)
A32S-PDUNR/L15-D400 LSD42BR/L - LCS4 - P-3 LSP4 LCL4 (EA-32) (SSHM5-6)
A40T-PDUNR/L15-D500 LSD42BR/L - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A50U-PDUNR/L15-D630 LSD42BR/L - LCS4 - P-3 LSP4 LCL4 - (SSHM6-6)
A32S-PDUNR/L1506-D400 ELSD42 - ELCS4 - P-3 LSP4S LCL44 (EA-20) (SSHM5-6)
A40T-PDUNR/L1506-D500 ELSD42 - ELCS4 - P-3 LSP4S LCL44 - (SSHM6-6)
A50U-PDUNR/L1506-D630 ELSD42 - ELCS4 - P-3 LSP4S LCL44 - (SSHM6-6)

A -P TU N R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h
øDs

95°
f

L2
f2

L1
α°
θ°
Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16M-PTUNR/L11-D200 STEEL 20 16 11 150 32 15 1 -6 -14 0.4 TN**1103... 1.7
A20Q-PTUNR/L11-D250 STEEL 25 20 13 180 36 18 1 -6 -12 0.4 TN**1103... 1.7
A25R-PTUNR/L16-D320 STEEL 32 25 17 200 45 23 1.4 -6 -12 0.8 TN**1604... 2.7
A32S-PTUNR/L16-D400 STEEL 40 32 22 250 50 30 1.3 -6 -10 0.8 TN**1604... 2.7

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The insert hole conforms to the ISO standard.
Tool holder length may be different to the ISO standard.
When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (PTUNL ** type), and the left hand insert (L) is used for the right hand
toolholders (PTUNR ** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw1 Clamping screw2 Wrench 1 Wrench 2 Spring Lever
(Optional parts) (Optional parts)
A16M-PTUNR/L11-D200 - LCS22A - P-2F - - LCL22N - (SSHM3-4)
A20Q-PTUNR/L11-D250 - LCS22A - P-2F - - LCL22N (EA-20) (SSHM3-4)
A25R-PTUNR/L16-D320 ELST317BR/L - LCS3 - P-2.5 LSP3 LCL33 (EA-25) (SSHM4-5)
A32S-PTUNR/L16-D400 LST317BR/L - LCS3 - P-2.5 LSP3 LCL3 (EA-32) (SSHM4-5)

B324 www.tungaloyamerica.com
A -PV U N R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h

øDs
93°
50˚

f
L2

f2
α° L1
θ°

Int. Toolholder
Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A25R-PVUNR/L16-D370 STEEL 37 25 22 200 45 23 9.5 -5 -14 0.8 V/YN**1604... 2.7
A32S-PVUNR/L16-D400 STEEL 40 32 22 250 50 30 6 -5 -12 0.8 V/YN**1604... 2.7
A40T-PVUNR/L16-D500 STEEL 50 40 27 300 60 37 7 -5 -10 0.8 V/YN**1604... 2.7

*Torque: Recommended torque (N·m) for clamping

**rε: Standard corner radius

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw Wrench Spring Lever
(Optional parts) (Optional parts)
A25R-PVUNR/L16-D370 LSV317BR/L LCS3V P-2.5 LSP3 LCL3V (EA-25) (SSHM4-5)
A32S-PVUNR/L16-D400 LSV317BR/L LCS3V P-2.5 LSP3 LCL3V (EA-32) (SSHM4-5)
A40T-PVUNR/L16-D500 LSV317BR/L LCS3V P-2.5 LSP3 LCL3V - (SSHM5-6)

A -PDZN R /L
Le v e r- l o c k b o r i n g b a r s , f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h
f2

93°

øDs
f

L2
α° L1
θ°
Cutting edge style Z Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A32S-PDZNR/L15-D400 STEEL 40 32 22 250 50 30 11.5 -6 -13 0.8 DN**1504... 4.8
A40T-PDZNR/L15-D500 STEEL 50 40 27 300 60 37 14.5 -6 -10 0.8 DN**1504... 4.8
A50U-PDZNR/L15-D630 STEEL 63 50 35 350 65 47 14.5 -6 -8 0.8 DN**1504... 4.8

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the right hand toolholders (PDZNR** type), and the left hand insert (L) is used for the left
hand toolholders (PDZNL** type).

SPARE PARTS
Oil supply attachment Screw for oil hole
Designation Shim Clamping screw Wrench Spring Lever
(Optional parts) (Optional parts)
A32S-PDZNR15-D400 LSZ42BR LCS4 P-3 LSP4 LCL4 (EA-32) (SSHM4-5)
A32S-PDZNL15-D400 LSZ42BL LCS4 P-3 LSP4 LCL4 (EA-32) (SSHM4-5)
A40T-PDZNR15-D500 LSZ42BR LCS4 P-3 LSP4 LCL4 - (SSHM5-6)
A40T-PDZNL15-D500 LSZ42BL LCS4 P-3 LSP4 LCL4 - (SSHM5-6)
A50U-PDZNR15-D630 LSZ42BR LCS4 P-3 LSP4 LCL4 - (SSHM6-6)
A50U-PDZNL15-D630 LSZ42BL LCS4 P-3 LSP4 LCL4 - (SSHM6-6)

Reference pages
A-PDUNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
A-PTUNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178
A-PVUNR/L: Inserts → B093 -, B104, CBN → B167 -, PCD → B178
A-PDZNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B325
 A -AC LN R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDm

95°

f2
α° L2

øDs
L1

θ°
Int. Toolholder

Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-ACLNR/L4-D20 STEEL 1.250 1.000 0.640 12.000 1.750 0.906 0.177 -6 -13 0.031 CN**43... 2.21
A20-ACLNR/L4-D25 STEEL 1.560 1.250 0.770 14.000 1.930 1.180 0.236 -6 -10 0.031 CN**43... 2.21
A24-ACLNR/L4-D32 STEEL 2.000 1.500 0.890 14.000 2.160 1.450 0.275 -6 -8 0.031 CN**43... 2.21
A32-ACLNR/L4-D40 STEEL 2.500 2.000 1.280 16.000 2.550 1.850 0.393 -6 -7 0.031 CN**43... 2.21

*NOTE: Dimension (h) is the distance between flats on the shank

*Torque: Recommended torque (lb·ft) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ACLNR/L4-D... ACP4S ACS-5W BP-7 SP-2.5 ASC422 CSTB-3.5 T-15F

A -AW LN R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e t r i g o n i n s e r t s

øDm

95°
f

L2
f2

α° L1

øDs
θ°
Cutting edge style L Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-AWLNR/L3-D20 STEEL 1.250 1.000 0.672 12.000 1.770 0.906 0.177 -6 -13 0.031 WN**33... 2.21
A20-AWLNR/L3-D25 STEEL 1.560 1.250 0.859 14.000 1.960 1.180 0.236 -6 -10 0.031 WN**33... 2.21
A16-AWLNR/L4-D20 STEEL 1.250 1.000 0.672 12.000 1.770 0.906 0.177 -6 -13 0.031 WN**43... 2.21
A20-AWLNR/L4-D25 STEEL 1.560 1.250 0.859 14.000 1.960 1.180 0.236 -6 -10 0.031 WN**43... 2.21
A24-AWLNR/L4-D32 STEEL 2.000 1.500 1.060 14.000 2.160 1.460 0.275 -6 -8 0.031 WN**43... 2.21
A32-AWLNR/L4-D40 STEEL 2.500 2.000 1.370 16.000 2.550 1.850 0.393 -6 -7 0.031 WN**43... 2.21

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-AWLNR/L3-D... ACP3S ACS-5W BP-7 SP-2.5 ASW322 CSTB-3.5 T-15F
A**-AWLNR/L4-D... ACP4S ACS-5W BP-7 SP-2.5 ASW422 CSTB-3.5 T-15F

Reference pages
A-ACLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178
A-AWLNR/L: Inserts → B097 -, CBN → B167

B326 www.tungaloyamerica.com
A -ASK N R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e s q u a re i n s e r t s

øDm
75°

f
L2

f2
α°

øDs
L1
θ°

Int. Toolholder
Cutting edge style K Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-ASKNR/L4-D20 STEEL 1.250 1.000 0.672 12.000 1.770 0.906 0.177 -6 -13 0.031 SN**43... 2.21
A20-ASKNR/L4-D25 STEEL 1.500 1.250 0.859 14.000 1.960 1.180 0.236 -6 -10 0.031 SN**43... 2.21

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ASKNR/L4-D... ACP4S ACS-5W BP-7 SP-2.5 ASS422 CSTB-3.5 T-15F

A -ATFN R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm
91°
f

L2
f2

øDs
L1
α°
θ°
Cutting edge style F Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16-ATFNR/L3-D20 STEEL 1.250 1.000 0.672 12.000 1.770 0.906 0.177 -6 -13 0.031 TN**33... 2.21
A20-ATFNR/L3-D25 STEEL 1.560 1.250 0.859 14.000 1.960 1.180 0.236 -6 -10 0.031 TN**33... 2.21

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ATFNR/L3-D... ACP3S ACS-5W BP-7 SP-2.5 AST322 CSTB-3.5 T-15F

Reference pages
A-ASKNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178
A-ATFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B327
 A -A D U N R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm
93°

f
β L2

f2

øDs
α° L1
θ°
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° β rε** Insert Torque*

A16-ADUNR/L4-D20 STEEL 1.250 1.000 0.672 12.000 1.770 0.906 0.177 -6 -13 30 0.031 DN**43... 2.21
A20-ADUNR/L4-D25 STEEL 1.500 1.250 0.859 14.000 1.960 1.180 0.236 -6 -11 20 0.031 DN**43... 2.21
A24-ADUNR/L4-D32 STEEL 2.000 1.500 1.063 14.000 2.160 1.450 0.275 -6 -8 15 0.031 DN**43... 2.21

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-ADUNR/L4-D... ACP4S ACS-5W BP-7 SP-2.5 ASD432 CSTB-3.5 T-15F

A -AV U N R /L
D o u b l e - c l a m p b o r i n g b a r, f o r n e g a t i v e 3 5 ° o r 2 5 ° r h o m b i c i n s e r t s

øDm
93°
f

25°
L2
f2

øDs
α° L1
θ°
Cutting edge style U Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A20-AVUNR/L3-D25 STEEL 1.560 1.250 0.859 14.000 1.960 1.180 0.236 -6 -10 0.031 V/YN**33... 2.21
A24-AVUNR/L3-D32 STEEL 2.000 1.500 1.060 14.000 2.160 1.440 0.275 -6 -8 0.031 V/YN**33... 2.21

*Torque: Recommended torque (lbf·ft) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamp screw Spring Spring pin Shim Shim screw Wrench
A**-AVUNR/L3-D... ACP3L ACS-5W BP-7 SP-2.5 ASV322 CSTB-3.5 T-15F

Reference pages
A-ADUNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
A-AVUNR/L: Inserts → B093 -, B104, CBN → B167 -, PCD → B178

B328 www.tungaloyamerica.com
A/E -SY U B R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 2 5 ° r h o m b i c i n s e r t s

øDm L2 h

øDs
93° 60˚

f2
L1
α°
θ°
Cutting edge style U Right hand (R) shown.

Int. Toolholder
Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*
A10-SYUBR/L2-D16 STEEL 1.000 0.625 0.625 7.000 1.250 0.600 0.312 0 -8 0.016 YW**11T2... 0.44
E08-SYUBR/L2-D14 CARBIDE 0.875 0.500 0.563 5.000 1.060 0.475 0.307 0 -8 0.016 YW**11T2... 0.44
E10-SYUBR/L2-D16 CARBIDE 1.000 0.625 0.625 7.000 1.250 0.600 0.307 0 -8 0.016 YW**11T2... 0.44

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A16Q-SYUBR/L11-D200 STEEL 20 16 15.5 180 35 15 8 0 -8 0.4 YW**11T2... 0.6
E12Q-SYUBR/L11-D200 CARBIDE 20 12 13.5 180 27 11 7.5 0 -8 0.4 YW**11T2... 0.6
E16R-SYUBR/L11-D245 CARBIDE 24.5 16 16 200 32 15 8 0 -8 0.4 YW**11T2... 0.6
*Torque: Recommended torque (lbf·ft,N·m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
A10-SYUBR/L2-D16 CSTB-2L T-6F
E**-SYUBR/L2-D... CSTB-2L T-6F
A16Q-SYUBR/L11-D200 CSTB-2L T-6F
E**-SYUBR/L11-D... CSTB-2L T-6F

A/E -SYQB R /L
S c re w - o n b o r i n g b a r s , f o r p o s i t i v e 2 5 ° r h o m b i c i n s e r t s

øDm h

øDs
122.5˚
f

30˚
L2
f2

α° L1
θ°

Cutting edge style Q Right hand (R) shown.

Inch Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A08-SYQBR/L2-D12 STEEL 0.750 0.500 0.438 5.000 1.000 0.475 0.188 0 -10 0.016 YW**11T2... 0.44
A10-SYQBR/L2-D14 STEEL 0.875 0.625 0.500 7.000 1.250 0.600 0.188 0 -8 0.016 YW**11T2... 0.44
E08-SYQBR/L2-D12 CARBIDE 0.750 0.500 0.438 5.000 1.000 0.475 0.188 0 -10 0.016 YW**11T2... 0.44
E10-SYQBR/L2-D14 CARBIDE 0.875 0.625 0.500 7.000 1.250 0.600 0.188 0 -8 0.016 YW**11T2... 0.44

Metric Material øDm øDs f L1 L2 h f2 θ° α° rε** Insert Torque*

A12M-SYQBR/L11-D170 STEEL 17 12 10.5 150 24 11 4.5 -5 -10 0.4 YW**11T2... 0.6
A16Q-SYQBR/L11-D215 STEEL 21.5 16 13 180 30 15 5 -5 -8 0.4 YW**11T2... 0.6
E12Q-SYQBR/L11-D170 CARBIDE 17 12 10.5 180 27 11 4.5 -5 -10 0.4 YW**11T2... 0.6
E16R-SYQBR/L11-D215 CARBIDE 21.5 16 13 200 32 15 5 -5 -8 0.4 YW**11T2... 0.6
*Torque: Recommended torque (lbf·ft,N·m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
A**-SYQBR/L2-D... CSTB-2L T-6F
E**-SYQBR/L2-D... CSTB-2L T-6F
A**-SYQBR/L11-D... CSTB-2L T-6F
E**-SYQBR/L11-D... CSTB-2L T-6F

Reference pages
A/E-SYUBR/L, A/E-SYQBR/L: Inserts → B155

Tungaloy B329
 T-SC LC R /L
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

øDs
øDm h
Carbide reinforcement
95°

b
f
L2 L3
L1
α°
θ°
Cutting edge style L Right hand (R) shown.
Int. Toolholder

Metric Material øDm Oil hole øDs f L1 L2 L3 h b α° θ° rε** Insert Torque*

T12M-SCLCR/L06 TSUPPARI 16 - 12 9 150 22 59 11 - -10 0 0.4 CC**0602... 1.2
T16Q-SCLCR/L09 TSUPPARI 20 - 16 11 180 27 59 15 - -10 0 0.8 CC**09T3... 3
T20R-SCLCR/L09C TSUPPARI 25 Rc1/4 20 13 200 35 49 18 - -8 0 0.8 CC**09T3... 3
T25S-SCLCR/L09C TSUPPARI 32 Rc1/4 25 17 250 40 64 23 - -6 0 0.8 CC**09T3... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The hole of inserts conforms to ISO standard.
When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLCL** type), and the left hand insert (L) is used for the right hand
toolholders (SCLCR** type).

SPARE PARTS
Designation Clamping screw Wrench
T12M-SCLCR/L06 CSTB-2.5 T-8F
T16Q-SCLCR/L09 CSTB-4S T-15F
T20R-SCLCR/L09C CSTB-4S T-15F
T25S-SCLCR/L09C CSTB-4S T-15F

T-SC LP R /L
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

øDs
øDm h
Carbide reinforcement
95°

b
f

L2 L3
L1
α°
θ°
Cutting edge style L Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h α° θ° rε** Insert Torque*

T12M-SCLPR08-D14 TSUPPARI 14 - 12 7 150 22 59 11 -4 5 0.4 CP**0802... 1.4
T12M-SCLPR/L08 TSUPPARI 16 - 12 9 150 25 59 11 -3 5 0.4 CP**0802... 1.4
T16Q-SCLPR09-D18 TSUPPARI 18 - 16 9 180 27 59 15 -3.5 5 0.8 CP**0903... 3
T16Q-SCLPR/L09 TSUPPARI 20 - 16 11 180 30 59 15 -4 5 0.8 CP**0903... 3
T20R-SCLPR09C-D22 TSUPPARI 22 Rc1/4 20 11 200 35 49 18 -2 5 0.8 CP**0903... 3
T20R-SCLPR/L09 TSUPPARI 25 - 20 13 200 35 49 18 -2 5 0.8 CP**0903... 3
T25S-SCLPR09C-D27 TSUPPARI 27 Rc1/4 25 13.5 250 40 64 23 -1 5 0.8 CP**0903... 3
T25S-SCLPR/L09 TSUPPARI 32 - 25 17 250 40 64 23 0 5 0.8 CP**0903... 3
*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SCLPL** type), and the left hand insert (L) is used for the right
hand toolholders (SCLPR** type).

SPARE PARTS
Designation Clamping screw Wrench
T12M-SCLPR/L08... CSTB-3L050 T-9F
T16Q-SCLPR09-D18 CSTB-4L060 T-15F
T16Q-SCLPR/L09 CSTB-4S T-15F
T20R-SCLPR09C-D22 CSTB-4L060 T-15F
T20R-SCLPR/L09 CSTB-4S T-15F
T25S-SCLPR09C-D27 CSTB-4L060 T-15F
T25S-SCLPR/L09 CSTB-4S T-15F

Reference pages
T-SCLCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179
T-SCLPR/L: Inserts → B113 -

B330 www.tungaloyamerica.com
T- STU P R /L
Ts u p p a r i - I c h i b a n b o r i n g b a r, f o r p o s i t i v e t r i a n g l e i n s e r t s

øDs
øDm Carbide reinforcement h
95°

b
f
L2 L1 L3
α°
θ°

Int. Toolholder
Cutting edge style U Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h θ° α° rε** Insert Torque*

T12M-STUPR11-D14 TSUPPARI 14 - 12 7 150 24 59 11 5 -4 0.4 TP**1102... 1.2
T12M-STUPR/L11 TSUPPARI 16 - 12 9 150 25 58 11 5 -4 0.4 TP**1102... 1.2
T16Q-STUPR13-D18 TSUPPARI 18 - 16 9 180 30 59 15 5 -3.5 0.4 TP**1303... 1.4
T16Q-STUPR/L13 TSUPPARI 20 - 16 11 180 30 59 15 5 -3 0.4 TP**1303... 1.4
T20R-STUPR13C-D22 TSUPPARI 22 Rc1/4 20 11 200 35 49 18 5 -2 0.4 TP**1303... 1.4
T20R-STUPR/L13 TSUPPARI 24 - 20 13 200 40 49 18 5 -2 0.4 TP**1303... 1.4
T25S-STUPR16C-D27 TSUPPARI 27 Rc1/4 25 13.5 250 40 64 23 5 -1 0.8 TP**16T3... 3
T25S-STUPR/L16 TSUPPARI 31 - 25 17 250 45 64 23 5 0 0.8 TP**16T3... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (STUPL** type), and the left hand insert (L) is used for the right
hand toolholders (STUPR** type).

SPARE PARTS
Designation Clamping screw Wrench
T12M-STUPR11-D14 CSTB-2.5B T-8F
T12M-STUPR/L11 CSTB-2.5 T-8F
T16Q-STUPR13-D18 CSTB-3S T-9F
T16Q-STUPR/L13 CSTB-3 T-9F
T20R-STUPR13C-D22 CSTB-3S T-9F
T20R-STUPR/L13 CSTB-3 T-9F
T25S-STUPR/L16... CSTB-4S T-15F

Reference pages
T-STUPR/L: Inserts → B138 -, CBN → B170 -, PCD → B180

Tungaloy B331
 T-SV U B R
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm h
Carbide reinforcement
93°

øDs
f
L2

f2
L4 L1 L3
α°
θ°
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 L4 h f2 θ° α° rε** Insert Torque*

T20R-SVUBR11C TSUPPARI 25 Rc1/4 20 14 200 30 59 121 18 4 0 -8 0.4 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (SVUBL** type), and the left hand insert (L) is used for the right
hand toolholders (SVUBR** type).

SPARE PARTS
Designation Clamping screw Wrench
T20R-SVUBR11C CSTB-2.5 T-8F

T-SV U C R
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm Carbide reinforcement

h

øDs
93°
f

L2 L3
f2

α° L1
θ°
Cutting edge style U Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

T25S-SVUCR16C TSUPPARI 32 Rc1/4 25 19 250 40 64 23 6.5 0 -5 0.8 VC**1604... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The hole of inserts conforms to ISO standard.
When using a right or left hand insert, the right hand insert (R) is used for left hand toolholders (L) and the left hand insert (L) is used for right hand toolholders (R).

SPARE PARTS
Designation Clamping screw Wrench
T25S-SVUCR16C CSTB-3.5L T-15F

Reference pages
T-SVUBR: Inserts → B147 -, CBN → B171 -
T-SVUCR: Inserts → B149 -, CBN → B171 -, PCD → B179 -

B332 www.tungaloyamerica.com
T- S D Q C R /L
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

øDm Carbide reinforcement h

107.5°

f
L2 L3

øDs
f2
L1
α°
θ°

Int. Toolholder
Cutting edge style Q Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

T16Q-SDQCR/L07 TSUPPARI 20 - 16 11 180 27 59 15 3 0 -6 0.4 DC**0702... 1.2
T20R-SDQCR/L11C TSUPPARI 25 Rc1/4 20 13 200 35 49 18 3 0 -6 0.8 DC**11T3... 3
T25S-SDQCR/L11C TSUPPARI 32 Rc1/4 25 17 250 40 64 23 4.5 0 -4 0.8 DC**11T3... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The hole of inserts conforms to ISO standard.
When using a right or left hand insert, the right hand insert (R) is used for left hand toolholders (L) and the left hand insert (L) is used for right hand toolholders (R).

SPARE PARTS
Designation Clamping screw Wrench
T16Q-SDQCR/L07 CSTB-2.5 T-8F
T20R-SDQCR/L11C CSTB-4M T-15F
T25S-SDQCR/L11C CSTB-4 T-15F

Reference pages
T-SDQCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B333
 T-SV Q B R
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm Carbide reinforcement h

117.5°

f2
L3

øDs
L2 L1
α°
θ°
Int. Toolholder

Cutting edge style Q Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

T20R-SVQBR11C TSUPPARI 25 Rc1/4 20 14 200 30 59 18 4 -5 -7 0.4 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The hole of inserts conforms to ISO standard. When using a right or left hand insert, the right hand instert (R) is used for the left hand toolholders (L), and the left
hand insert (L) is used for the right hand toolholders (R).

SPARE PARTS
Designation Clamping screw Wrench
T20R-SVQBR11C CSTB-2.5 T-8F

T-SV Q C R
Ts u p p a r i - I c h i b a n , S c re w - o n b o r i n g b a r, f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

øDm Carbide reinforcement h

117.5°
f

f2

L3

øDs
α° L2 L1
θ°
Cutting edge style Q Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h f2 θ° α° rε** Insert Torque*

T25S-SVQCR16C TSUPPARI 32 Rc1/4 25 17 250 40 64 23 8 0 -5 0.8 VC**1604... 3

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: The hole of inserts conforms to ISO standard. When using a right or left hand insert, the right hand instert (R) is used for the left hand toolholders (L), and the left
hand insert (L) is used for the right hand toolholders (R).

SPARE PARTS
Designation Clamping screw Wrench
T25S-SVQCR16C CSTB-3.5L T-15F

Reference pages
T-SVQBR: Inserts → B147 -, CBN → B171 -
T-SVQCR: Inserts → B149 -, CBN → B171 -, PCD → B179 -

B334 www.tungaloyamerica.com
S-C S K P R /L
C l a m p - o n b o r i n g b a r, f o r p o s i t i v e s q u a re i n s e r t s

øDs
øDm h

b
75°

f
L2
α° L1

5°

Int. Toolholder
Cutting edge style K Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S16Q-CSKPR09 STEEL 20 16 11 180 30 15 15 -4 0.8 SP**0903...
S20R-CSKPR/L09 STEEL 25 20 13 200 40 18 18.5 -2 0.8 SP**0903...
S25S-CSKPR12 STEEL 32 25 17 250 45 23 22.5 0 0.8 SP**1203...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert (R) is used for left hand toolholders (L) and the left hand insert (L) is used for right hand toolholders (R).

SPARE PARTS
Designation Clamp set Wrench
S16Q-CSKPR09 CSG-5S P-2.5
S20R-CSKPR/L09 CSG-5 P-2.5
S25S-CSKPR12 CSG-6 P-3

S/C -CTFP R /L
C l a m p - o n s t y l e b o r i n g b a r, f o r p o s i t i v e t r i a n g l e i n s e r t s

øDs
øDm h
91°

b
f

L2 L1
α°
5°

Cutting edge style F Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S12M-CTFPR/L11 STEEL 16 12 9 150 25 11 11.5 -6 0.4 TP**1103...
S16Q-CTFPR/L11 STEEL 20 16 11 180 30 15 15 -4 0.4 TP**1103...
S20R-CTFPR/L16 STEEL 25 20 13 200 40 18 18.5 -2 0.8 TP**1603...
S25S-CTFPR/L16 STEEL 32 25 17 250 45 23 22.5 0 0.8 TP**1603...
S32T-CTFPR/L16 STEEL 40 32 22 300 50 30 29.5 0 0.8 TP**1603...
C12Q-CTFPR/L11 CARBIDE 16 12 9 180 - 11 - -6 0.4 TP**1103...
C16R-CTFPR/L11 CARBIDE 20 16 11 200 - 15 - -4 0.4 TP**1103...

**rε: Standard corner radius

Note: The hole of inserts conforms to ISO standard.
When using a right or left hand insert, the right hand insert (R) is used for left hand toolholders (L) and the left hand insert (L) is used for right hand toolholders (R).

SPARE PARTS
Designation Clamp set 1 Clamp set 2 Wrench
S12M-CTFPR/L11 CSW-00 - P-2.5
S16Q-CTFPR/L11 - CSG-5S P-2.5
S20R-CTFPR/L16 - CSG-6S P-3
S**-CTFPR/L16 - CSG-6 P-3
C12Q-CTFPR/L11 CSW-00 - P-2.5
C16R-CTFPR/L11 - CSG-5S P-2.5

Reference pages
S-CSKPR/L: Inserts → B132, CBN → B170, PCD → B179
S/C-CTFPR/L: Inserts → B145 -, CBN → B170 -, PCD → B180

Tungaloy B335
 T-P C LN R
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDs
95° øDm Carbide reinforcement h

b
f
L2 L3
α° L1
95°

θ°
Int. Toolholder

Cutting edge style L Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h θ° α° rε** Insert Torque*

T16Q-PCLNR09 TSUPPARI 20 - 16 11 180 27 59 15 -6 -14 0.8 CN**0903... 1.7
T20R-PCLNR09C TSUPPARI 25 Rc1/4 20 13 200 35 49 18 -6 -12 0.8 CN**0903... 1.7
T25S-PCLNR09C TSUPPARI 32 Rc1/4 25 17 250 40 64 23 -6 -11 0.8 CN**0903... 1.7
T32U-PCLNR12C TSUPPARI 40 Rc1/2 32 22 350 50 103 30 -6 -11 0.8 CN**1204... 4.8
T40V-PCLNR12C TSUPPARI 50 Rc1/2 40 27 400 55 88 37 -6 -10 0.8 CN**1204... 4.8
T50W-PCLNR12C TSUPPARI 63 Rc1/2 50 35 450 65 63 47 -6 -8 0.8 CN**1204... 4.8

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
T**-PCLNR09... - LCS22A - P-2F - - LCL32N
T**-PCLNR12C LSC42BR - LCS4 - P-3 LSP4 LCL4

S-PC LN R /L
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

øDs
95° øDm h

b
f

L2 L1
α°
95°
θ°

Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b θ° α° rε** Insert Torque*

S16M-PCLNR/L09 STEEL 20 16 11 150 30 15 15.5 -6 -14 0.8 CN**0903... 1.7
S20Q-PCLNR/L09 STEEL 25 20 13 180 35 18 19 -6 -12 0.8 CN**0903... 1.7
S25R-PCLNR/L09 STEEL 32 25 17 200 40 23 24 -6 -11 0.8 CN**0903... 1.7
S32S-PCLNR/L12 STEEL 40 32 22 250 50 30 29.5 -6 -11 0.8 CN**1204... 4.8
S40T-PCLNR/L12 STEEL 50 40 27 300 55 37 37.5 -6 -10 0.8 CN**1204... 4.8
S50U-PCLNR/L12 STEEL 63 50 35 350 65 47 47.5 -6 -8 0.8 CN**1204... 4.8

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
S**-PCLNR/L09 - LCS22A - P-2F - - LCL32N
S32S-PCLNR/L12 LSC42BR/L - LCS4 - P-3 LSP4 LCL4
S40T-PCLNR/L12 LSC42BR/L - LCS4 - P-3 LSP4 LCL4
S50U-PCLNR/L12 LSC42BR/L - LCS4 - P-3 LSP4 LCL4

Reference pages
T-PCLNR, S-PCLNR/L: Inserts → B052 -, CBN → B165, PCD → B178

B336 www.tungaloyamerica.com
S-PW LN R /L
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e t r i g o n i n s e r t s

95° øDm h

øDs

b
f
L2 L1
95° α°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S16M-PWLNR/L06 STEEL 20 16 11 150 30 15 15.5 -17 0.8 WN**0604...
S20Q-PWLNR/L06 STEEL 25 20 13 180 35 18 19 -14 0.8 WN**0604...
S25R-PWLNR/L06 STEEL 32 25 17 200 40 23 24 -12 0.8 WN**0604...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
S**-PWLNR/L06 - LCS33 - P-2F - - LCL33N
S25R-PWLNR06 LSW312BR - LCS3B - P-2.5 LSP3 LCL3
S25R-PWLNL06 LSW312BL - LCS3B - P-2.5 LSP3 LCL3

S-PSK N R
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e s q u a re i n s e r t s

øDm h

øDs

b
75°
f

L2
L1
α°
6°

Cutting edge style K Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S32S-PSKNR12 STEEL 40 32 22 250 50 30 29.5 -10 0.8 SN**1204...
S40T-PSKNR12 STEEL 50 40 27 300 55 37 37.5 -10 0.8 SN**1204...
S50U-PSKNR12 STEEL 63 50 35 350 65 47 47.5 -8 0.8 SN**1204...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw Wrench Spring Lever
S**-PSKNR12 LSS42BR LCS4 P-3 LSP4 LCL4

Reference pages
S-PWLNR/L: Inserts → B097 -, CBN → B167
S-PSKNR: Inserts → B073 -, CBN → B166 -, PCD → B178

Tungaloy B337
 S-PTFN R /L
Le v e r l o c k t y p e b o r i n g b a r, f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h

øDs
91°

b
f
L2
L1
α°

6°
Int. Toolholder

Cutting edge style F Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert Torque*

S32S-PTFNR/L16 STEEL 40 32 22 250 50 30 29.5 -10 0.8 TN**1604... 2.7
S40T-PTFNR/L16 STEEL 50 40 27 300 55 37 37.5 -10 0.8 TN**1604... 2.7
S50U-PTFNR16 STEEL 63 50 35 350 65 47 47.5 -8 0.8 TN**1604... 2.7

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw Wrench Spring Lever
S32S-PTFNR16 LST317BR LCS3 P-2.5 LSP3 LCL3
S32S-PTFNL16 LST317BL LCS3 P-2.5 LSP3 LCL3
S40T-PTFNR16 LST317BR LCS3 P-2.5 LSP3 LCL3
S40T-PTFNL16 LST317BL LCS3 P-2.5 LSP3 LCL3
S50U-PTFNR16 LST317BR LCS3 P-2.5 LSP3 LCL3

T-P D U N R
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDs
øDm Carbide reinforcement h
93°

b
f

L2 L3
f2

α° L1
6°

Cutting edge style U Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h f2 α° rε** Insert

T32U-PDUNR15C TSUPPARI 40 Rc1/2 32 22 350 50 103 30 6 -13 0.8 DN**1504...
T40V-PDUNR15C TSUPPARI 50 Rc1/2 40 27 400 55 88 37 7 -10 0.8 DN**1504...
T50W-PDUNR15C TSUPPARI 63 Rc1/2 50 35 450 65 63 47 10 -8 0.8 DN**1504...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw Wrench Spring Lever
T**-PDUNR15C LSD42BR LCS4 P-3 LSP4 LCL4

Reference pages
S-PTFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178
T-PDUNR: Inserts → B063 -, CBN → B165 -, PCD → B178

B338 www.tungaloyamerica.com
S-PD U N R /L
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h

b
93°

øDs
L2

f
α° L1

6°
Cutting edge style U Right hand (R) shown.

Int. Toolholder
Metric Material øDm øDs f L1 L2 h b α° rε** Insert
S20Q-PDUNR/L11 STEEL 25 20 13 180 35 18 19 -14 0.8 DN**1104...
S25R-PDUNR/L11 STEEL 32 25 17 200 40 23 24 -12 0.8 DN**1104...
S32S-PDUNR/L15 STEEL 40 32 22 250 50 30 29.5 -13 0.8 DN**1504...
S40T-PDUNR/L15 STEEL 50 40 27 300 55 37 37.5 -10 0.8 DN**1504...
S50U-PDUNR/L15 STEEL 63 50 35 350 65 47 47.5 -8 0.8 DN**1504...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
S20Q-PDUNR/L11 - LCS22A - P-2F - - LCL33NL
S25R-PDUNR11 ELSD317BR - LCS3 - P-2.5 LSP3 LCL33L
S25R-PDUNL11 ELSD317BL - LCS3 - P-2.5 LSP3 LCL33L
S32S-PDUNR15 LSD42BR - LCS4 - P-3 LSP4 LCL4
S32S-PDUNL15 LSD42BL - LCS4 - P-3 LSP4 LCL4
S40T-PDUNR15 LSD42BR - LCS4 - P-3 LSP4 LCL4
S40T-PDUNL15 LSD42BL - LCS4 - P-3 LSP4 LCL4
S50U-PDUNR15 LSD42BR - LCS4 - P-3 LSP4 LCL4
S50U-PDUNL15 LSD42BL - LCS4 - P-3 LSP4 LCL4

T- PTU N R
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm Carbide reinforcement h

øDs
95°

b
f

L2 L1 L3

α°
6°

Cutting edge style U Right hand (R) shown.

Metric Material øDm Oil hole øDs f L1 L2 L3 h α° rε** Insert Torque*

T16Q-PTUNR11 TSUPPARI 20 - 16 11 180 27 59 15 -14 0.4 TN**1103... 1.7
T20R-PTUNR11C TSUPPARI 25 Rc1/4 20 13 200 35 49 18 -12 0.4 TN**1103... 1.7
T25S-PTUNR16C TSUPPARI 32 Rc1/4 25 17 250 40 64 23 -12 0.8 TN**1604... 2.7
T32U-PTUNR16C TSUPPARI 40 Rc1/2 32 22 350 50 103 30 -10 0.8 TN**1604... 2.7
T40V-PTUNR16C TSUPPARI 50 Rc1/2 40 27 400 55 88 37 -10 0.8 TN**1604... 2.7
T50W-PTUNR16C TSUPPARI 63 Rc1/2 50 35 450 65 63 47 -8 0.8 TN**1604... 2.7
*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: • The hole of inserts conforms to ISO standard.
• Toolholder lengths do not always conform to ISO.
• When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
T**-PTUNR11... - LCS22A - P-2F - - LCL22N
T25S-PTUNR16C ELST317BR - LCS3 - P-2.5 LSP3 LCL33
T**-PTUNR16C LST317BR - LCS3 - P-2.5 LSP3 LCL3

Reference pages
S-PDUNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178
T-PTUNR: Inserts → B082 -, CBN → B166 -, PCD → B178

Tungaloy B339
 A /S -P TU N R /L
Le v e r l o c k t y p e b o r i n g b a r, f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h
95°

b
L3

øDs
L2

f
L1
α°

6°
Int. Toolholder

Cutting edge style U Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert Torque*

S16M-PTUNR/L11 STEEL 20 16 11 150 30 15 15.5 -14 0.4 TN**1103... 1.7
S20Q-PTUNR/L11 STEEL 25 20 13 180 35 18 19 -12 0.4 TN**1103... 1.7
S25R-PTUNR/L16 STEEL 32 25 17 200 40 23 24 -12 0.8 TN**1604... 2.7
A32S-PTUNR/L16 STEEL 40 32 22 250 50 30 29.5 -12 0.8 TN**1604... 2.7

*Torque: Recommended torque (N∙m) for clamping **rε: Standard corner radius
Note: • The hole of inserts conforms to ISO standard.
• Toolholder lengths do not always conform to ISO.
• When using a right or left hand insert, the right hand insert is used for left hand toolholders and the left hand insert is used for right hand toolholders.

SPARE PARTS
Oil supply attachment
Designation Shim Clamping screw 1 Clamping screw 2 Wrench 1 Wrench 2 Spring Lever
(Optional parts)
S**-PTUNR/L11 - LCS22A - P-2F - - LCL22N -
S25R-PTUNR16 ELST317BR - LCS3 - P-2.5 LSP3 LCL33 -
S25R-PTUNL16 ELST317BL - LCS3 - P-2.5 LSP3 LCL33 -
A32S-PTUNR16 LST317BR - LCS3 - P-2.5 LSP3 LCL3 (EA-32)
A32S-PTUNL16 LST317BL - LCS3 - P-2.5 LSP3 LCL3 (EA-32)

S-PDZN R /L
Le v e r- l o c k b o r i n g b a r, f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h
93°

b
f

øDs
25
f2

α° L2 L1
6°

Cutting edge style Z Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h f2 b α° rε** Insert

S32S-PDZNR/L15 STEEL 40 32 22 275 55 30 6 29.5 -13 0.8 DN**1504...
S40T-PDZNR15 STEEL 50 40 27 325 60 37 7 37.5 -10 0.8 DN**1504...
S50U-PDZNR15 STEEL 60 50 35 375 65 47 10 47.5 -8 0.8 DN**1504...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert is used for right hand toolholders and the left hand insert is used for left hand toolholders.

SPARE PARTS
Designation Shim Clamping screw Wrench Spring Lever
S32S-PDZNR15 LSZ42BR LCS4 P-3 LSP4 LCL4
S32S-PDZNL15 LSZ42BL LCS4 P-3 LSP4 LCL4
S*0*-PDZNR15 LSZ42BR LCS4 P-3 LSP4 LCL4

Reference pages
A/S-PTUNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178
S-PDZNR/L: Inserts → B063 -, CBN → B165 -, PCD → B178

B340 www.tungaloyamerica.com
S-M C LN R /L
M u l t i - c l a m p b o r i n g b a r, f o r n e g a t i v e 8 0 ° r h o m b i c i n s e r t s

95° øDm

f
L2 L1

øDs
α°
95°

5°

Int. Toolholder
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S25R-MCLNR/L12 STEEL 32 25 17 200 40 23 22.5 -12 0.8 CN**1204...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (MCLNL** type), and the left hand insert (L) is used for the right
hand toolholders (MCLNR** type).

SPARE PARTS
Designation Clamp Pin Clamping screw Wrench 1 Wrench 2
S25R-MCLNR/L12 MCPM-21 MLP44 MCS620-3 P-3 P-2.5F

S-M W LN R /L
M u l t i - c l a m p b o r i n g b a r, f o r n e g a t i v e t r i g o n i n s e r t s

95° øDm h

øDs

b
f

L2 L1
α°
6°

95°
Cutting edge style L Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S25R-MWLNR/L08 STEEL 32 25 17 200 40 23 22.5 -12 0.8 WN**0804...
S32S-MWLNR/L08 STEEL 44 32 22 250 50 30 29.5 -10 0.8 WN**0804...
S40T-MWLNR/L08 STEEL 54 40 27 300 60 37 37.5 -10 0.8 WN**0804...
S50U-MWLNR/L08 STEEL 70 50 35 350 75 47 47.5 -10 0.8 WN**0804...

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Pin Clamping screw Shim Wrench 1 Wrench 2
S25R-MWLNR/L08 MCPM-6 MLP44 MCS520-2.5 - P-2.5 P-2.5F
S32S-MWLNR/L08 MCPM-6 MLP46 MCS520-2.5 MSW-432BR/L P-2.5 P-2.5F
S40T-MWLNR/L08 MCPM-6 MLP46 MCS520-2.5 MSW-432BR/L P-2.5 P-2.5F
S50U-MWLNR/L08 MCPM-6 MLP46 MCS520-2.5 MSW-432BR/L P-2.5 P-2.5F

Reference pages
S-MCLNR/L: Inserts → B052 -, CBN → B165 -, PCD → B178
S-MWLNR/L: Inserts → B097 -, CBN → B167

Tungaloy B341
 S-M SK N R /L
M u l t i - c l a m p b o r i n g b a r, f o r n e g a t i v e s q u a re i n s e r t s

øDm h
75°

øDs

b
f
L2 L1
α°
Int. Toolholder

Cutting edge style K Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S25R-MSKNR/L12 STEEL 32 25 17 200 40 23 22.5 -12 0.8 SN**1204...
**rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (MSKNL** type), and the left hand insert (L) is used for the right
hand toolholders (MSKNR** type).

SPARE PARTS
Designation Clamp Pin Clamping screw Wrench 1 Wrench 2
MCPM-21
S25R-MSKNR/L12 MLP44 MCS620-3 P-3 P-2.5F
MCL-6*

Note: * marked parts type No. in former type No.

S-M TFN R /L
M u l t i - c l a m p b o r i n g b a r, f o r n e g a t i v e t r i a n g l e i n s e r t s

øDm h

øDs

b
95°
f

L2 L1
α°
5°

Cutting edge style F Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S25R-MTFNR/L16 STEEL 32 25 17 200 40 23 22.5 -12 0.8 TN**1604...

**rε: Standard corner radius

Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (MTFNL** type), and the left hand insert (L) is used for the right
hand toolholders (MTFNR** type).

SPARE PARTS
Designation Clamp Pin Clamping screw Wrench1 Wrench 2
MCPM-6
S25R-MTFNR/L16 MLP33L MCS520-2.5 P-2.5 P-2F
MCL-5M*

Note: * marked parts type No. in former type No.

Reference pages
S-MSKNR/L: Inserts → B073 -, CBN → B166 -, PCD → B178
S-MTFNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178

B342 www.tungaloyamerica.com
S-M D U N R /L
M u l t i - c l a m p b o r i n g b a r, f o r n e g a t i v e 5 5 ° r h o m b i c i n s e r t s

øDm h

øDs

b
90°

f
L2
L1

5°

Int. Toolholder
Cutting edge style U α° Right hand (R) shown.

Metric Material øDm øDs f L1 L2 h b α° rε** Insert

S25R-MDUNR/L11 STEEL 32 25 17 200 40 23 22.5 -12 0.8 DN**1104...
**rε: Standard corner radius
Note: When using a right or left hand insert, the right hand insert (R) is used for the left hand toolholders (MDUNL** type), and the left hand insert (L) is used for the right
hand toolholders (MDUNR** type).

SPARE PARTS
Designation Clamp Pin Clamping screw Wrench 1 Wrench 2
MCPM-21
S25R-MDUNR/L11 MLP33L MCS620-3 P-3 P-2F
MCL-6*

Note: * marked parts type No. in former type No.

Reference pages
S-MDUNR/L: Inserts → B063 -

Tungaloy B343
 B LM sl eeves
Standard Sleeves for SJB-Mini series with round shank

h S2 S3
S1

øDn

øDs
ødi
A B C
10 L
Int. Toolholder

Metric øDs ødi øDn L h S1 S2 S3

BLM159-04 15.875 (0.625") 4 15 100 15 5 15 15
BLM159-05 15.875 (0.625") 5 15 100 15 5 15 15
BLM159-06 15.875 (0.625") 6 15 100 15 5 20 20
BLM159-07 15.875 (0.625") 7 15 100 15 5 20 20
BLM16-04 16 4 15 100 15 5 15 15
BLM16-05 16 5 15 100 15 5 15 15
BLM16-06 16 6 15 100 15 5 20 20
BLM16-07 16 7 15 100 15 5 20 20
BLM19-04 19.05 (0.750") 4 18 100 18 5 15 15
BLM19-05 19.05 (0.750") 5 18 100 18 5 15 15
BLM19-06 19.05 (0.750") 6 18 100 18 5 20 20
BLM19-07 19.05 (0.750") 7 18 100 18 5 20 20
BLM20-04 20 4 13 100 19 5 15 15
BLM20-05 20 5 14 100 19 5 15 15
BLM20-06 20 6 15 100 19 5 20 20
BLM20-07 20 7 16 100 19 5 20 20
BLM22-04 22 4 13 125 21 5 15 15
BLM22-05 22 5 14 125 21 5 15 15
BLM22-06 22 6 15 125 21 5 20 20
BLM22-07 22 7 16 125 21 5 20 20
BLM25-04 25 4 13 125 24 5 15 15
BLM25-05 25 5 14 125 24 5 15 15
BLM25-06 25 6 15 125 24 5 20 20
BLM25-07 25 7 16 125 24 5 20 20
BLM254-04 25.4 (1.000") 4 13 125 24 5 15 15
BLM254-05 25.4 (1.000") 5 14 125 24 5 15 15
BLM254-06 25.4 (1.000") 6 15 125 24 5 20 20
BLM254-07 25.4 (1.000") 7 16 125 24 5 20 20

SPARE PARTS
Seal cap
Designation Clamping screw A Clamping screw B, C Wrench
(Optional parts: inner screw)
BLM159, 16... SSHM4-4 SSHM4-4 P-2 CA-16(M6)
BLM19-04 SSHM4-4 SSHM4-6 P-2 CA-16(M6)
BLM19-05, 06, 07 SSHM4-4 SSHM4-4 P-2 CA-16(M6)
BLM20-04, 05 SSHM4-4 SSHM4-6 P-2 CA-16(M6)
BLM20-06, 07 SSHM4-4 SSHM4-4 P-2 CA-16(M6)
BLM22-... SSHM4-4 SSHM4-6 P-2 CA-16(M6)
BLM25-04, 05 SSHM4-4 SSHM4-8 P-2 CA-16(M6)
BLM25-06 SSHM4-4 SSHM4-8 P-2 CA-16(M6)
BLM25-07 SSHM4-4 SSHM4-6 P-2 CA-16(M6)
BLM254-04, 05, 06 SSHM4-4 SSHM4-8 P-2 CA-16(M6)
BLM254-07 SSHM4-4 SSHM4-6 P-2 CA-16(M6)

B344 www.tungaloyamerica.com
BLS sl eeves
Slee v e s f o r b o r i ng b ar s w i t h sq uare shank ( re gu l a r l e n gt h )

25
ø14 (10)
4-M6 (3-M6) b

ødi
45

16
h

Int. Toolholder
Metric ødi L h b
BLS16-08 8 125 28 12.5
BLS16-10 10 125 28 12.5
BLS16-12 12 125 28 12.5

SPARE PARTS
Designation Wrench
BLS16-... P-3

BLS-C sl eeves
S l e e v e s f o r b o r i n g b a r s w i t h s q u a re s h a n k ( s h o r t t y p e )

L
50
40 30
10
25

3-M6 b
ødi

16
h

R3/8

Metric ødi L h b
BLS16-08C 8 100 28 12.5
BLS16-10C 10 100 28 12.5
BLS16-12C 12 100 28 12.5

SPARE PARTS
Designation Wrench
BLS16-**C P-3

Tungaloy B345
 B LM sl eeves
Sl e e v e s f o r b o r i ng b ar s w i t h ro und shank

ødi 3-M5X0.8

øDs
b
h L
Int. Toolholder

Metric ødi øDs L h b

BLM19-08 8 19.05 100 18 18
BLM20-08 8 20 100 19 18
BLM22-08 8 22 125 21 21
BLM254-08 8 25.4 125 24 24
BLM25-08C 8 25 55 24 23
BLM25-10C 10 25 55 24 23
BLM25-12C 12 25 55 24 23

SPARE PARTS
Designation Wrench
BLM... P-2.5

B LC sl eeves
Standard Sleeves for boring bars with round shank

R2 R1 Flat
R2 R1
øDs

øDs
ødi

Metric ødi ℓ1 ℓ2 øDs

BLC40-8 8 73 13 40
BLC40-10 10 73 13 40
BLC40-12 12 73 13 40
BLC40-16 16 73 13 40
BLC32-8C 8 45 20 32
BLC32-10C 10 45 20 32
BLC32-12C 12 45 20 32
BLC40-8C 8 55 13 40
BLC40-10C 10 55 13 40
BLC40-12C 12 55 13 40
BLC40-16C 16 55 13 40

SPARE PARTS
Designation Wrench
BLC40-8 P-3
BLC40-1... P-4
BLC32-8C P-3
BLC32-1*C P-4
BLC40-8C P-3
BLC40-1*C P-4

B346 www.tungaloyamerica.com
C-PC LN L-C H P
Le v e r l o c k t y p e i nter nal to o l ho l d er w i t h Tung Ca p c on n e c t i on w i t h 95° a p p roa c h a n gl e . For n e ga t i v e 8 0 °
r h o m b i c i n s e r t . H i g h - p re s s u re c o o l a n t c a p a b i l i t y.

øD1
95° øDm

øD

f
0

f2
95° L2
L1

Int. Toolholder
Cutting edge style L
Metric øDm øD øD1 L1 L2 f f2 rε** Insert
C6PCLNL17100-12-CHP 32 63 25 100 67.5 17 4.5 0.8 CN**1204...
Applicable for 14 MPa pressure coolant
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Coolant unit Wrench Lever
C6PCLNL17100-12-CHP LCS43 S-CU-CHP P-2.5F LCL43N

C-PD U N L-C H P
Le v e r l o c k t y p e i nter nal to o l ho l d er w i t h Tung Ca p c on n e c t i on w i t h 93° a p p roa c h a n gl e . For n e ga t i v e 5 5 °
r h o m b i c i n s e r t . H i g h - p re s s u re c o o l a n t c a p a b i l i t y.

øD1
øDm
93°
øD

f
0
f2 L2
Cutting edge style U L1 Left hand (L) shown.

Metric øDm øD øD1 L1 L2 f f2 rε** Insert

C6PDUNL17100-1104-CHP 32 63 25 100 67.5 17 4.5 0.8 DN**1104...

Applicable for 14 MPa pressure coolant

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Coolant unit Wrench Spring pin Lever
C6PDUNL17100-1104-CHP ELSD317BL LCS43 S-CU-CHP P-2.5 LSP3 LCL33L

Reference pages
C-PCLNL-CHP: Inserts → B052 -, CBN → B165 -, PCD → B178
C-PDUNL-CHP: Inserts → B063 -, CBN → B165 -, PCD → B178

Tungaloy B347
 Tur nLine - Miniature Machining
Inch Metric

B19 0, B2 8 8
Economical double-sided inserts with excellent sharpness

B 3 62
Toolholders for small-part machining

I N I
B386
Solid boring bars for turning small diameters with high precision

Other Tool for Miniature B409

Machining

C009
Innovative clamping system for stable parting operations
W = 0.039 - 0.079"

C 0 47
4-cornered inserts with good clamping rigidity for highly precise grooving and parting
W = 0.02 - 0.125"

C055
Unique insert geometry for highly precise grooving
W = 0.013 - 0.118"

C 0 59
Multi-functional tool series for various grooving operations
W = 0.055 - 0.315"

C137
Highly rigid clamping system for wide grooving and profiling in one pass
W = 0.394 - 0.984"

B348 www.tungaloyamerica.com
Te tr a M i n i - C u t

Tungaloy B349
 Miniature E x ter nal Tur ning - Q uick Guide
Facing
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JSDFCR/L Screw-on clamping

91°
Cutting edge angle 91° 䘟 12 - 16 mm with offset B369
Insert type: DC ††

External Turning
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JTTACR/L
91° Cutting edge angle 91° 䘟 8 - 16 mm Back side clamping B370
without offset
Insert type: TC ††
Miniature Tool

JSTACR/L Screw-on clamping

91° Cutting edge angle 91° 䘟 8 - 16 mm
without offset
B370
Insert type: TC ††

JSCGCR/L Screw-on clamping

91° Cutting edge angle 91° 䘟 12 - 16 mm with offset B365
Insert type: CC ††

JSCACL Screw-on clamping

91° Cutting edge angle 91° 䘟 10 - 12 mm without offset B364
Insert type: CC ††

JTTANR/L Back side clamping

91° Cutting edge angle 91° 䘟 12 - 16 mm without offset B377
Insert type: TN ††

Back Turning
Inch
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JSTBR/L
Insert type: JTBR/L3 ††
䘟 0.375" - 0.625" Screw-on clamping B381

Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JSTBR/L
Insert type: JTBR/L3 ††
䘟 10 - 16 mm Screw-on clamping B381

JS-TBL3
Insert type: JTBR3 †† 䘟 ø19.05 - 25.4 mm Screw-on clamping B381

JSEGR/L
Insert type: J10ER/L ††
䘟 10 - 16 mm Screw-on clamping B383

JSXBR/L
Insert type: JXBR/L8 ††
䘟 10 - 25 mm Screw-on clamping B380

B350 www.tungaloyamerica.com
Front & Reverse Turning
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JSXGR/L
Insert type: JXFR/L8
䘟 10 - 25 mm Screw-on clamping B379
JXRR/L8

External Turning & Facing

Inch
Type of insert See
Style Description Positive Negative Shank Size Clamping style page
95°
JSCL2CR/L Screw-on clamping
Cutting edge angle 95° 䘟 0.375" - 0.625"
without offset
B362
5° Insert type: CC ††

Miniature Tool
JSVL2PR/L Screw-on clamping
Cutting edge angle 95° 䘟 0.500" - 0.625" without offset B375
95° Insert type: VP ††
95°
JPWL2XR/L Side clamping
Cutting edge angle 95° 䘟 0.375" - 0.625" without offset B190
5° Insert type: WXGU
95°
JSWL2XR/L Screw-on clamping
Cutting edge angle 95° 䘟 0.375" - 0.625"
without offset
B190
5° Insert type: WXGU
95°
JSWL2XR/L-CHP Screw-on clamping
Cutting edge angle 95° 䘟 0.500"
without offset
B191
5° Insert type: WXGU
95°
JSWLXR-F Screw-on clamping
Cutting edge angle 95° 䘟 0.500" - 0.625"
with offset
B191
Insert type: WXGU

Tungaloy B351
 Miniature E x ter nal Tur ning - Q uick Guide
External Turning & Facing
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page
95°
JTCL2CR/L
Cutting edge angle 95° 䘟 8 - 16 mm Back side clamping B362
without offset
5° Insert type: CC ††
95°
JSCL2CR/L Screw-on clamping
Cutting edge angle 95° 䘟 10 - 16 mm
without offset
B362
5° Insert type: CC ††

JSVL2PR/L Screw-on clamping

Cutting edge angle 95° 䘟 10 - 16 mm without offset B375
95° Insert type: VP ††
95°
JSCLCR/L Screw-on clamping
Cutting edge angle 95° 䘟 8 - 16 mm with offset B363
5° Insert type: CC ††
95°
Miniature Tool

JPWL2XR/L Side clamping

Cutting edge angle 95° 䘟 10 - 16 mm without offset B190
5° Insert type: WXGU
95°
JSWL2XR/L Screw-on clamping
Cutting edge angle 95° 䘟 10 - 20 mm
without offset
B190
5° Insert type: WXGU
95°
JSWL2XR/L-CHP Screw-on clamping
Cutting edge angle 95° 䘟 12 mm
without offset
B191
5° Insert type: WXGU
95°
JSWLXR-F Screw-on clamping
Cutting edge angle 95° 䘟 10 - 16 mm
with offset
B191
Insert type: WXGU
95°
PCLNR Lever-lock clamping
Cutting edge angle 95° 䘟 20 mm
with offset
B376
5° Insert type: CN ††
95°
PCL2NR Lever-lock clamping
Cutting edge angle 95° 䘟 20 mm
without offset
B376
Insert type: CN ††

JTTLNR/L Back side clamping

Cutting edge angle 95° 䘟 12 - 16 mm
without offset
B377
95°
Insert type: TN ††

PTL2NR/L Lever-lock clamping

Cutting edge angle 95° 䘟 20 mm
without offset
B378
95°
Insert type: TN ††

B352 www.tungaloyamerica.com
External Turning & Profiling
Inch
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

30° JPDJ2XR/L
93° Cutting edge angle 93° 䘟 0.375" - 0.625" Side clamping B192
without offset
Insert type: DXGU

30° JSDJ2XR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 0.375" - 0.625"
without offset
B192
Insert type: DXGU

30° JSDJ2XR/L-CHP Screw-on clamping

93° Cutting edge angle 93° 䘟 0.500"
without offset
B193
Insert type: DXGU

30° JSDJ2CR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 0.375" - 0.625" without offset B365
Insert type: DC ††

Miniature Tool
30° JSDJ2CR/L-CHP Screw-on clamping
93° Cutting edge angle 93° 䘟 0.500"
without offset
B367
Insert type: DC ††

JSDNCN Screw-on clamping

62.5° 62.5° Cutting edge angle 62.5° 䘟 0.375" - 0.625"
with offset
B368
Insert type: DC ††
30°
JSDJXR-F Screw-on clamping
93°
Cutting edge angle 93° 䘟 0.500" - 0.625"
with offset
B193
Insert type: DXGU
50°
JPVJ2XR/L Side clamping
93°
Cutting edge angle 93° 䘟 0.375" - 0.625"
without offset
B194
Insert type: VXGU
50°
JSVJ2XR/L-CHP Screw-on clamping
93°
Cutting edge angle 93° 䘟 0.500"
without offset
B195
Insert type: VXGU
50°
JSVJ2XR/L Screw-on clamping
93°
Cutting edge angle 93° 䘟 0.375" - 0.625"
without offset
B194
Insert type: VXGU

50° JSVJ2BR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 0.375" - 0.625"
without offset
B371
Insert type: VB ††

50° JSVJ2BR/L-CHP Screw-on clamping

93° Cutting edge angle 93° 䘟 0.500"
without offset
B372
Insert type: VB ††
50°
JSVJXR-F Screw-on clamping
93° Cutting edge angle 93° 䘟 0.500" - 0.625"
with offset
B195
Insert type: VXGU

JS-SDUXL
Cutting edge angle 93° 䘟 ø0.625" - 1.000" Screw-on clamping B196
with offset
93° Insert type: DXGU

JS-SVUXL Screw-on clamping

Cutting edge angle 93° 䘟 ø0.625" - 1.000"
with offset
B197
93° Insert type: VXGU

Tungaloy B353
 Miniature E x ter nal Tur ning - Q uick Guide
External Turning & Profiling
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

30° JPDJ2XR/L
93° Cutting edge angle 93° 䘟 10 - 16 mm Side clamping B192
without offset
Insert type: DXGU

30° JSDJ2XR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 10 - 20 mm
without offset
B192
Insert type: DXGU

30° JSDJ2XR/L-CHP Screw-on clamping

93° Cutting edge angle 93° 䘟 12 mm
without offset
B193
Insert type: DXGU

30° JTDJ2CR/L Back side clamping

93° Cutting edge angle 93° 䘟 10 - 16 mm without offset B366
Insert type: DC ††
Miniature Tool

30° JSDJ2CR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 8 - 16 mm without offset B365
Insert type: DC ††

30° JSDJ2CR/L-CHP Screw-on clamping

93° Cutting edge angle 93° 䘟 12 mm
without offset
B367
Insert type: DC ††

JSDJCR/L Screw-on clamping

30°
Cutting edge angle 93° 䘟 8 - 16 mm with offset B367
93°
Insert type: DC ††

JSDNCN Screw-on clamping

62.5° 62.5° Cutting edge angle 62.5° 䘟 10 - 16 mm
with offset
B368
Insert type: DC ††
62.5°
JSDN3CR/L Screw-on clamping
62.5°
Cutting edge angle 62.5° 䘟 12 - 16 mm
with offset
B368
Insert type: DC ††
30°
JSDJXR-F Screw-on clamping
93°
Cutting edge angle 93° 䘟 10 - 16 mm
with offset
B193
Insert type: DXGU
50°
JPVJ2XR/L Side clamping
93°
Cutting edge angle 93° 䘟 10 - 16 mm
without offset
B194
Insert type: VXGU
50°
JSVJ2XR/L-CHP Screw-on clamping
93°
Cutting edge angle 93° 䘟 12 mm
without offset
B195
Insert type: VXGU
50°
JSVJ2XR/L Screw-on clamping
93°
Cutting edge angle 93° 䘟 10 - 20 mm
without offset
B194
Insert type: VXGU

50° JSVJ2BR/L Screw-on clamping

93° Cutting edge angle 93° 䘟 10 - 16 mm
without offset
B371
Insert type: VB ††

50° JSVJ2BR/L-CHP Screw-on clamping

93° Cutting edge angle 93° 䘟 12 mm
without offset
B372
Insert type: VB ††
50° JSVABR/L Screw-on clamping
91° Cutting edge angle 91° 䘟 10 - 16 mm
without offset
B372
Insert type: VB ††

JSVP2PR/L Screw-on clamping

Cutting edge angle 117.5° 䘟 10 - 16 mm
without offset
B375
117.5°
Insert type: VP ††

B354 www.tungaloyamerica.com
External Turning & Profiling
Metric
Type of insert
See
Style Description Positive Negative Shank Size Clamping style page

JSVNBN Screw-on clamping

Cutting edge angle 72.5° 䘟 10 - 16 mm
with offset
B374
72.5°
Insert type: VB ††

JSVJBR/L Screw-on clamping

93° 50° Cutting edge angle 93° 䘟 10 - 16 mm
with offset
B371
Insert type: VB ††
50°
JSVJXR-F Screw-on clamping
93° Cutting edge angle 93° 䘟 10 - 16 mm
with offset
B195
Insert type: VXGU

JS-SDUCL Screw-on clamping

Cutting edge angle 93° 䘟 ø19.05 - 25.4 mm
with offset
B369
93° Insert type: DC ††

Miniature Tool
JS-SDUXL
Cutting edge angle 93° 䘟 ø14 - 25.4 mm Screw-on clamping B196
with offset
93° Insert type: DXGU

JS-SVUXL Screw-on clamping

Cutting edge angle 93° 䘟 ø15.875 - 25.4 mm
with offset
B197
93° Insert type: VXGU

PDJNR Lever-lock clamping

93° Cutting edge angle 93° 䘟 20 mm with offset B376
Insert type: DN ††

Tungaloy B355
 Miniature Inter nal Tur ning - Q uick Guide
Positive type

ISO Insert
Inch
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r ( i n)

Y-Pro
Style Description & Application Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SEXPR/L Steel ø0.313 ø0.250
Boring & Internal facing 䘟 B302
Insert type: EP †† Carbide ø0.313 ø0.250

SCLCR/L ø0.375 -
Steel ø1.000 ø0.500 ø1.250
Boring & internal facing 䘟 ø0.375 -
B299
Insert type: CC †† Carbide ø0.500 ø1.250
ø1.000
STUPR/L ø0.313 - ø0.438 ø1.250
Steel ø1.000
Boring 䘟 B310
Insert type: TP †† Carbide ø0.313 - ø0.438 ø0.875
ø0.625
STFPR/L
ø0.375 -
Blind hole boring 䘟 Carbide ø0.750 ø0.500 ø1.000 B309
Insert type: TP ††

ø0.375 -
Miniature Tool

SCLPR/L Steel ø0.500 ø0.875

ø0.625
Boring & internal facing 䘟 ø0.375 -
B303
Insert type: CP †† Carbide ø0.500 ø0.875
ø0.625
STFCR/L
ø0.375 -
Blind hole boring 䘟 Carbide ø0.750 ø0.430 ø0.930 B308
Insert type: TC ††

SDUCR/L ø0.375 -
Steel ø0.750 ø0.625 ø1.000
30˚ Boring & internal profiling 䘟 B313
Insert type: DC †† Carbide ø0.375 - ø0.625 ø1.000
ø0.750
SVUCR/L
50˚ ø0.625 -
Boring & internal profiling 䘟 Steel ø0.875 ø1.000 B315
Insert type: VC †† ø0.750

SVUBR/L
50˚
Boring & internal profiling 䘟 Steel ø0.750 ø1.000 B314
Insert type: VB ††

SDQCR/L
Boring & internal profiling ø0.375 -
15.5˚ 䘟 Steel ø0.625 ø0.625 ø0.875 B316
Insert type: DC ††

SVQCR/L
Boring & internal profiling ø0.500 -
25.5˚ 䘟 Steel ø0.625 ø0.688 ø1.000 B318
Insert type: VC ††

SVQBR/L
25.5˚ Boring & internal profiling 䘟 Steel ø0.625 ø1.000 B317
Insert type: VB ††

SDZCR/L
30˚ Internal retracting 䘟 Steel ø0.625 ø0.875 B319
Insert type: DC ††

SVZCR/L
ø0.500 -
50˚ Internal retracting 䘟 Steel ø0.750 ø0.750 ø1.000 B320
Insert type: VC ††

B356 www.tungaloyamerica.com
 ISO Insert
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r ( i n)

Y-Pro
Style Description & Application Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SVZBR/L
50˚
Internal retracting 䘟 Steel ø0.750 ø1.000 B320
Insert type: VB ††

SVJCR/L
Internal sphere cutting 䘟 Steel ø0.625 ø1.000 B306
Insert type: VC ††

SVJBR/L
Internal sphere cutting 䘟 Steel ø0.625 ø1.000 B306
Insert type: VB ††

SYQBR/L ø0.500 -
Steel ø0.625 ø0.750 ø0.875
30˚ Internal undercut & profiling 䘟 B329
Insert type: YW †† Carbide ø0.500 - ø0.750 ø0.875
ø0.625

Miniature Tool
SYUBR/L ø1.000
60˚ Steel ø0.625
Boring & internal profiling 䘟 ø0.500 -
B329
Insert type: YW †† Carbide ø0.875 ø1.000
ø0.625

Tungaloy B357
 Miniature Inter nal Tur ning - Q uick Guide
Positive type

ISO Insert
Metric
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r (m m)

Y-Pro
Ty p e Ø See
Style Description & Application page
0 10 20 30 40 50
SEXPR/L
Steel ø4 - ø8 ø4.5 ø7
Boring & Internal facing 䘟 B302
Insert type: EP †† Carbide ø4 - ø8 ø4.5 ø7

SCLCR/L Steel ø4 - ø25 ø5 ø27

Boring & internal facing 䘟 B300
Insert type: CC †† Carbide ø4 - ø25 ø5 ø27

SWUBR/L Steel ø5 - ø8 ø6 ø8
Boring 䘟 B312
Insert type: WB †† Carbide ø5 - ø8 ø6 ø8

STUPR/L Steel ø7 - ø32 ø8 ø34

Boring 䘟 B311
Insert type: TP †† Carbide ø7 - ø25 ø8 ø27
Miniature Tool

STFPR/L Steel ø8 - ø25 ø10 ø27

Blind hole boring 䘟 B309
Insert type: TP †† Carbide ø8 - ø20 ø10 ø22

SCLPR/L Steel ø8 - ø25 ø10 ø27

Boring & internal facing 䘟 B304
Insert type: CP †† Carbide ø8 - ø16 ø10 ø20

STFCR/L Steel ø10 - ø16 ø12 ø18

Blind hole boring 䘟 B308
Insert type: TC †† Carbide ø10 - ø16 ø12 ø18

SDUCR/L Steel ø10 - ø25 ø13 ø32

30˚ Boring & internal profiling 䘟 B313
Insert type: DC †† Carbide ø10 - ø20 ø13 ø27

SVUCR/L Steel ø12 - ø25 ø16 ø32

50˚
Boring & internal profiling 䘟 B315
Insert type: VC †† Carbide ø12 - ø25 ø18 ø32

SVUBR/L Steel ø16 - ø25 ø20 ø32

50˚
Boring & internal profiling 䘟 B314
Insert type: VB †† Carbide ø16 - ø25 ø24.5 ø34

SDQCR/L
Steel ø10 - ø25 ø13 ø30
15.5˚ Boring & internal profiling 䘟 B316
Insert type: DC †† Carbide ø10 - ø20 ø13 ø25

SVQCR/L Steel ø10 - ø16 ø13.5 ø21.5

25.5˚ Boring & internal profiling 䘟 B318
Insert type: VC †† Carbide ø10 - ø16 ø13.5 ø21.5

SVQBR/L Steel ø12 - ø25 ø17 ø30.5

25.5˚ Boring & internal profiling 䘟 B317
Insert type: VB †† Carbide ø12 - ø25 ø17 ø30.5

SDZCR/L Steel ø12 - ø25 ø14 ø25

30˚ Internal retracting 䘟 B319
Insert type: DC †† Carbide ø12 - ø16 ø18 ø22

SVZCR/L
50˚ Internal retracting 䘟 Steel ø12 ø16 B320
Insert type: VC ††

B358 www.tungaloyamerica.com
 ISO Insert
StreamJet-Bar Shank Shank M i n . b o r e d i a m e t e r (m m)

Y-Pro
Ty p e Ø See
Style Description & Application page
0 10 20 30 40 50
SVZBR/L
50˚
Internal retracting 䘟 Steel ø16 - ø32 ø20 ø40 B320
Insert type: VB ††

SEZPR/L Steel ø4 - ø5 ø5.5 ø6.5

Internal retracting 䘟 B321
Insert type: EP †† Carbide ø4 - ø5 ø5.5 ø6.5

SVJCR/L
Internal sphere cutting 䘟 Steel ø12 - ø16 ø16 ø20 B306
Insert type: VC ††

SVJBR/L
Internal sphere cutting 䘟 Steel ø20 - ø25 ø25 ø30 B306
Insert type: VB ††

Miniature Tool
SYQBR/L Steel ø12 - ø16 ø17 ø21.5
30˚ Internal undercut & profiling 䘟 B329
Insert type: YW †† Carbide ø12 - ø16 ø17 ø21.5

SYUBR/L Steel ø16 ø20

60˚
Boring & internal profiling 䘟 B329
Insert type: YW †† Carbide ø12 - ø16 ø20 ø24.5

Miniature Inter nal Tur ning - Q uick Guide

Double-sided insert with positive cutting edges
Inch
MiniForce-Turn MiniForce S h a n k Shank M i n . b o r e d i a m e t e r ( i n)
Style Description & Application -Turn Ty p e Ø See
0 0.375 0.750 1.125 1.500 2.000 page
SWLXR/L ø0.375 -
Steel ø0.750 ø0.500 ø1.000
Boring & facing 䘟 B288
Insert type: WXGU Carbide ø0.375 - ø0.500 ø1.000
ø0.750
SDXXR/L ø0.375 -
15.5˚ Steel ø0.750 ø0.625 ø1.000
Internal profiling 䘟 ø0.375 -
B288
Insert type: DXGU Carbide ø0.625 ø1.000
ø0.750
SDZXR/L
Internal retracting ø0.500 -
26˚ 䘟 Steel ø0.750
ø0.625 ø0.875 B289
Insert type: DXGU

Tungaloy B359
 Miniature Inter nal Tur ning - Q uick Guide
TinyMini-Turn - Solid carbide tools for small diameters turning
Metric

Boring, profiling, chamfering

Shank M i n . b o r e d i a m e t e r ø D m (m m)
TinyMini-Turn øDs
Style See
Description & Application (mm) 0 2 4 6 8 10 page
JBT
Boring, profiling, ø4 & ø7 ø0.6 ø7 B386
& chamfering
JBP
Boring & chamfering ø4 & ø7 ø2.8 ø5 B387

JBU
Back boring & chamfering ø7 ø5 B387

JBC
Boring & 45o chamfering ø7 ø5 ø6.8 B387
Miniature Tool

JBB
Back boring ø4 & ø7 ø3 ø7 B388

Threading
Shank
TinyMini-Turn M i n . b o r e d i a m e t e r ø D m (m m)
øDs See
Style
Description & Application (mm) 0 2 4 6 8 10 page
JBI
Threading ø4 & ø7 ø4 ø7 B388
(Metric thread)

Grooving
S h a n k G r o ove M i n . b o r e d i a m e t e r ø D m (m m)
TinyMini-Turn øDs width See
Style D e s c r i p t i o n & A p p l i c a t i o n (m m) (m m) 0 2 4 6 8 10 12 14 15 page
JBG
Grooving ø4 & ø7 0.5 - 2 ø2 ø6.8 B389

JBF
Face grooving ø7 1-3 ø6 ø15 B390

JBS
Face grooving ø7 2 ø6 B390
(for shaft)
JBR
Boring & profiling ø7 1 ø5 ø6.8 B391
(full radius type)

B360 www.tungaloyamerica.com
MEMO

Miniature Tool

Tungaloy B361
 JS C L2C R /L
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 9 5° a p p roa c h a n gl e f or p os i t i v e 80° r h om b i c i n s e r t s

95° Without offset

b
f
L2
95° L1

h1

h
Cutting edge style L2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSCL2CR/L062 0.375 0.375 5.000 0.400 0.375 0.375 0.016 CC**21.5... 0.89
JSCL2CR/L082 0.500 0.500 5.000 0.400 0.500 0.500 0.016 CC**21.5... 0.89
JSCL2CR/L103 0.625 0.625 5.000 0.680 0.625 0.625 0.031 CC**32.5... 0.89

Metric h b L1 L2 h1 f rε** Insert Torque

JSCL2CR/L1010K06 10 10 120 12 10 10 0.4 CC**0602... 1.2
JSCL2CR/L1212K06 12 12 85 12 12 12 0.4 CC**0602... 1.2
JSCL2CR/L1212X06 12 12 120 12 12 12 0.4 CC**0602... 1.2
Miniature Tool

JSCL2CL1212K06 12 12 125 12 12 12 0.4 CC**0602... 1.2

JSCL2CR/L1212F09 12 12 85 16 12 12 0.8 CC**09T3... 1.2
JSCL2CR/L1212X09 12 12 120 16 12 12 0.8 CC**09T3... 1.2
JSCL2CR/L1616X09 16 16 120 16 16 16 0.8 CC**09T3... 1.2

*Torque: Recommended torque (lbf∙ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSCL2CR/L... CSTB-2.5 T-8F

JTC L2C R /L
Ba c k c l a m p too l ho l d er w i t ho ut o f f set w i t h 95° a p p roa c h a n gl e f or p os i t i v e 80° r h om b i c i n s e r t s

95° Without offset

b
f

L2
95° L1
h1

Cutting edge style L2 Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JTCL2CL0810K06 8 10 125 12 8 10 0.4 CC**0602... 0.9
JTCL2CR/L1010X06 10 10 120 12 10 10 0.4 CC**0602... 0.9
JTCL2CR/L1212F09 12 12 85 16 12 12 0.8 CC**09T3... 1.2
JTCL2CR/L1212X09 12 12 120 16 12 12 0.8 CC**09T3... 1.2
JTCL2CR/L1616X09 16 16 120 16 16 16 0.8 CC**09T3... 1.2
JTCL2CR1616M09 16 16 150 16 16 16 0.8 CC**09T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamping screw Wrench
JTCL2CR/L**06 JCP-2 JDS-3525 P-2F
JTCL2CR/L**09 JCP-3 JDS-5040 P-2.5F

Reference pages
JSCL2CR/L, JTCL2CR/L: Inserts → B106 -, CBN → B170 -, PCD → B179

B362 www.tungaloyamerica.com
J SC LC R /L
S c re w - o n to o l h o l d e r w i t h 9 5 ° a p p ro a c h a n g l e f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

95°

b
f
L2
95° L1

h1

h
Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSCLCR/L0808H06 8 8 100 12 8 10 0.4 CC**0602... 1.2
JSCLCR/L1010H06 10 10 100 12 10 12 0.4 CC**0602... 1.2
JSCLCR/L1212H09 12 12 100 16 12 16 0.8 CC**09T3... 1.2
JSCLCR/L1616H09 16 16 100 16 16 20 0.8 CC**09T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

Miniature Tool
SPARE PARTS
Designation Clamping screw Wrench
JSCLCR/L**H06 CSTB-2.5 T-8F
JSCLCR/L**H09 CSTB-4SD T-8F

J SC LC R -F
S c re w -o n s te p p e d - head to o l ho l d er w i t h 9 5 ° a p p roa c h a n gl e f or p os i t i v e 80° r h om b i c i n s e r t s

95° L1
L3
95°
f1

b
f

L4
h1

Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 L3 L4 h1 f f1 rε** Insert Torque*

JSCLCR1216F09-F15 12 16 85 12 27 12.5 12 15 28 0.2 CC**09T3... 1.2
JSCLCR1216X09-F15 12 16 120 12 27 12.5 12 15 28 0.2 CC**09T3... 1.2
JSCLCR1620X09-F15 16 20 120 12 27 12.5 16 15 28 0.2 CC**09T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSCLCR**F15 CSTB-4SD T-8F

Reference pages
JSCLCR/L, JSCLCR-F: Inserts → B106 -, CBN → B170 -, PCD → B179

Tungaloy B363
 JS CAC L
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 9 1° a p p roa c h a n gl e f or p os i t i v e 80° r h om b i c i n s e r t s

Without offset

b
f
L2
L1
91°

h1

h
Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSCACL1010H06 10 10 100 12 10 10 0.4 CC**0602... 1.2
JSCACL1212H09 12 12 100 16 12 12 0.8 CC**09T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
Miniature Tool

JSCACL1010H06 CSTB-2.5 T-8F

JSCACL1212H09 CSTB-4SD T-8F

Reference pages
JSCACL: Inserts → B106 -, CBN → B170 -, PCD → B179

B364 www.tungaloyamerica.com
J SC G C R /L
S c re w - o n to o l h o l d e r w i t h 9 1 ° a p p ro a c h a n g l e f o r p o s i t i v e 8 0 ° r h o m b i c i n s e r t s

b
f
L2
L1
91°

h1

h
Cutting edge style G Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSCGCR/L1212H06 12 12 100 12 12 16 0.4 CC**0602... 1.2
JSCGCR/L1616H09 16 16 100 16 16 20 0.8 CC**09T3... 1.2
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSCGCR/L1212H06 CSTB-2.5 T-8F

Miniature Tool
JSCGCR/L1616H09 CSTB-4SD T-8F

J SD J2C R /L
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e f or p os i t i v e 55° r h om b i c i n s e r t s

Without offset

b
f

f2
JSDJ2CR/L1010X11
L2 JSDJ2CR/L1212F11
L1 JSDJ2CR/L1212X11
30°
93°
h1

Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L062 0.375 0.375 5.000 0.500 0.375 0.375 - 0.016 DC**21.5... 0.89
JSDJ2CR/L082 0.500 0.500 5.000 0.500 0.500 0.500 - 0.016 DC**21.5... 0.89
JSDJ2CR/L103 0.625 0.625 5.000 0.780 0.625 0.625 - 0.031 DC**32.5... 0.89

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L0808F07 8 8 85 14 8 8 - 0.4 DC**0702... 1.2
JSDJ2CR/L1010X07 10 10 120 14 10 10 - 0.4 DC**0702... 1.2
JSDJ2CR/L1010X11 10 10 120 20 10 10 4 0.8 DC**11T3... 1.2
JSDJ2CR/L1212F07 12 12 85 14 12 12 - 0.4 DC**0702... 1.2
JSDJ2CR/L1212F11 12 12 85 20 12 12 2 0.8 DC**11T3... 1.2
JSDJ2CR/L1212X07 12 12 120 14 12 12 - 0.4 DC**0702... 1.2
JSDJ2CL1212K07 12 12 125 14 12 12 - 0.4 DC**0702... 1.2
JSDJ2CR/L1212X11 12 12 120 20 12 12 2 0.8 DC**11T3... 1.2
JSDJ2CR/L1616X11 16 16 120 20 16 16 - 0.8 DC**11T3... 1.2

*Torque: Recommended torque (lbf∙ft, N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSDJ2CR/L062/082, JSDJ2CR/L**07 CSTB-2.5 T-8F
JSDJ2CR/L103, JSDJ2CR/L**11 CSTB-4SD T-8F

Reference pages
JSCGCR/L: Inserts → B106 -, CBN → B170 -, PCD → B179
JSDJ2CR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B365
 JTD J2C R /L
Ba c k c l a m p too l ho l d er w i t ho ut o f f set w i t h 93° a p p roa c h a n gl e f or p os i t i v e 55° r h om b i c i n s e r t s

Without offset
JTDJ2CR/L1212F11

b
f

f2
JTDJ2CR/L1212X11
L2
L1
30°
93°

h1

h
Cutting edge style J2 Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JTDJ2CR/L1010X07 10 10 120 14 10 10 - 0.4 DC**0702... 0.9
JTDJ2CR/L1212F07 12 12 85 14 12 12 - 0.4 DC**0702... 0.9
JTDJ2CR/L1212X07 12 12 120 14 12 12 - 0.4 DC**0702... 0.9
JTDJ2CR/L1212F11 12 12 85 20 12 12 2 0.8 DC**11T3... 1.2
JTDJ2CR/L1212X11 12 12 120 20 12 12 2 0.8 DC**11T3... 1.2
JTDJ2CL1212M11 12 12 150 20 12 12 - 0.8 DC**11T3... 1.2
JTDJ2CR/L1616X11 16 16 120 20 16 16 - 0.8 DC**11T3... 1.2
Miniature Tool

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamping screw Wrench
JTDJ2CR/L**07 JCP-2 JDS-3525 P-2F
JTDJ2CR/L**11 JCP-3 JDS-5040 P-2.5F

JS D JC R -F
Sc re w -o n s te p p ed - head to o l ho l d er w i t h 9 3° a p p roa c h a n gl e f or p os i t i v e 55° r h om b i c i n s e r t s

L1
L3
93°
b
f2
f

L2
h1

L4
h

Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 L3 L4 h1 f f2 rε** Insert Torque*

JSDJCR1016X07-F15 10 16 120 12.5 27 14 10 15 26 0.4 DC**0702... 1.2
JSDJCR1216F07-F15 12 16 85 12.5 27 14 12 15 26 0.4 DC**0702... 1.2
JSDJCR1216X07-F15 12 16 120 12.5 27 14 12 15 26 0.4 DC**0702... 1.2
JSDJCR1216F11-F15 12 16 85 12.5 27 20 12 15 28 0.8 DC**11T3... 1.2
JSDJCR1216X11-F15 12 16 120 12.5 27 20 12 15 28 0.8 DC**11T3... 1.2
JSDJCR1620X11-F15 16 20 120 12.5 27 20 16 15 28 0.8 DC**11T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSDJCR**07-F15 CSTB-2.5 T-8F
JSDJCR**11-F15 CSTB-4SD T-8F

Reference pages
JTDJ2CR/L, JSDJCR-F: Inserts → B116 -, CBN → B170 -, PCD → B179

B366 www.tungaloyamerica.com
J SD J2C R /L-C H P
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e f or p os i t i v e 55° r h om b i c i n s e r t s ,
wit h c h a n n e l s f or hi g h p ressure co o l ant
L1 Without offset

b
f2
30°

L2

h
93°

h1
Cutting edge style J2 5/16”-24UNF Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L082-CHP 0.500 0.500 3.344 0.710 0.500 0.500 0.710 0.008 DC**21.5... 0.7

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSDJ2CR/L1212F07-CHP 12 12 85 18 12 12 18 0.4 DC**0702... 1.2
JSDJ2CR/L1212F11-CHP 12 12 85 19 12 12 20.5 0.8 DC**11T3... 1.2
*Torque: Recommended torque (lbf∙ft, N∙m) for clamping
**rε: Standard corner radius

Miniature Tool
SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSDJ2CR/L082-CHP,
CSTB-2.5 S-CU-CHP T-8F
JSDJ2CR/L1212F07-CHP
JSDJ2CR/L1212F11-CHP CSTB-4SD S-CU-CHP T-8F

J SD JC R /L
S c re w - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

b
f

L2
30°
L1
93°
h1

Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSDJCR/L0808H07 8 8 100 14 8 10 0.4 DC**0702... 1.2
JSDJCR/L1010H11 10 10 100 18 10 12 0.8 DC**11T3... 1.2
JSDJCR/L1212H07 12 12 100 14 12 16 0.4 DC**0702... 1.2
JSDJCR/L1212H11 12 12 100 18 12 16 0.8 DC**11T3... 1.2
JSDJCR/L1616H11 16 16 100 18 16 20 0.8 DC**11T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSDJC**H07 CSTB-2.5 T-8F
JSDJC**H11 CSTB-4SD T-8F

Reference pages
JSDJ2CR/L-CHP, JSDJCR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B367
 JS D N C N
S c re w - o n to o l h o l d e r w i t h 6 2 . 5 ° a p p ro a c h a n g l e f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

b
L2
62.5° L1

h1

h
Cutting edge style N
Inch h b L1 L2 h1 f rε** Insert Torque*
JSDNCN062 0.375 0.375 5.000 0.550 0.375 0.375 0.016 DC**21.5... 0.89
JSDNCN082 0.500 0.500 5.000 0.550 0.500 0.500 0.016 DC**21.5... 0.89
JSDNCN103 0.625 0.625 5.000 0.826 0.625 0.625 0.031 DC**32.5... 0.89

Metric h b L1 L2 h1 f rε** Insert Torque*

JSDNCN1010X07 10 10 120 15 10 5 0.4 DC**0702... 1.2
JSDNCN1010X11 10 10 120 21 10 5 0.8 DC**11T3... 1.2
Miniature Tool

JSDNCN1212F07 12 12 85 15 12 6 0.4 DC**0702... 1.2

JSDNCN1212X07 12 12 120 15 12 6 0.4 DC**0702... 1.2
JSDNCN1212F11 12 12 85 21 12 6 0.8 DC**11T3... 1.2
JSDNCN1212H11 12 12 100 21 12 6 0.8 DC**11T3... 1.2
JSDNCN1212X11 12 12 120 21 12 6 0.8 DC**11T3... 1.2
JSDNCN1616X11 16 16 120 21 16 8 0.8 DC**11T3... 1.2
*Torque: Recommended torque (lbf∙ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSDNCN062/082, JSDNCN**07 CSTB-2.5 T-8F
JSDNCN103, JSDNCN**11 CSTB-4SD T-8F

JS D N 3C R /L
Sc re w -o n to o l ho l d er w i t h 6 2 .5 ° ap p ro ach a n gl e (N 3- s t y l e ) f or p os i t i v e 55° r h om b i c i n s e r t s

62.5°
b
f

L2
L1
h1

Cutting edge style N3 Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSDN3CR1212H07 12 12 105 100 12 18 0.4 DC**0702... 1.2
JSDN3CR1616H11 16 16 107 100 16 25 0.8 DC**11T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSDN3CR1212H07 CSTB-2.5 T-8F
JSDN3CR1616H11 CSTB-4SD T-8F

Reference pages
JSDNCN, JSDN3CR/L: Inserts → B116 -, CBN → B170 -, PCD → B179

B368 www.tungaloyamerica.com
J SD FC R /L
S c re w -o n to o l h o l d er f o r f aci ng w i t h 9 1 ° ap p roa c h a n gl e f or p os i t i v e 55° r h om b i c i n s e r t s

91°

b
f
L2
L1

h1

h
Cutting edge style F Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSDFCR/L1212H07 12 12 100 8 12 16 0.4 DC**0702... 1.2
JSDFCR/L1616H11 16 16 100 10.5 16 22 0.8 DC**11T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench

Miniature Tool
JSDFCR/L1212H07 CSTB-2.5 T-8F
JSDFCR/L1616H11 CSTB-4SD T-8F

J S-S D U C L
S c re w - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e f o r p o s i t i v e 5 5 ° r h o m b i c i n s e r t s

SDUCL07 L1 SDUCL11
L3

f2
h øDs
0.0

f
L2

G
f2
f

93°

B
B

h
Cutting edge style U Left hand (L) shown.

Metric øDs f f2 L1 L2 L3 h B G rε** Insert Torque*

JS19K-SDUCL07 19.05 6 5 125 20 25 18 11.5 - 0.4 DC**0702... 1.2
JS20K-SDUCL07 20 6 5 125 20 25 19 11.5 - 0.4 DC**0702... 1.2
JS22K-SDUCL07 22 6 5 125 20 25 21 11.5 - 0.4 DC**0702... 1.2
JS19K-SDUCL11 19.05 10 6 125 20 25 18 11.5 1.525 0.8 DC**11T3... 1.2
JS20K-SDUCL11 20 10 6 125 20 25 19 11.5 1 0.8 DC**11T3... 1.2
JS22K-SDUCL11 22 11 6 125 20 25 21 11.5 1 0.8 DC**11T3... 1.2
JS25K-SDUCL11 25.4 12 6 125 20 25 24 12.7 0.7 0.8 DC**11T3... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JS**K-SDUCL07 CSTB-2.5 T-8F
JS**K-SDUCL11 CSTB-4SD T-8F

Reference pages
JSDFCR/L, JS-SDUCL: Inserts → B116 -, CBN → B170 -, PCD → B179

Tungaloy B369
 JSTAC R /L
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 9 1° a p p roa c h a n gl e f or p os i t i v e 60° t r i a n gl e i n s e r t s

Without offset

b
f
L2
L1

h1

h
91°

Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSTACR/L0808K08 8 8 125 10 8 8 0.2 TC**0802... 0.6
JSTACR/L1010K08 10 10 125 10 10 10 0.2 TC**0802... 0.6
JSTACR/L1212K11 12 12 125 12 12 12 0.4 TC**1102... 1.2
JSTACR/L1616H11 16 16 100 12 16 16 0.4 TC**1102... 1.2
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius
Miniature Tool

SPARE PARTS
Designation Clamping screw Wrench
JSTACR/L**K08 CSTB-2L T-6F
JSTACR/L**11 CSTB-2.5 T-8F

JTTAC R /L
Ba c k c l a m p too l ho l d er w i t ho ut o f f set w i t h 91° a p p roa c h a n gl e f or p os i t i v e 60° t r i a n gl e i n s e r t s

Without offset

b
f

L2
L1
91°
h1

h
Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JTTACL0810K08 8 10 125 10 8 10 0.2 TC**0802... 0.9
JTTACR/L1212M11 12 12 150 12 12 12 0.4 TC**1102... 0.9
JTTACR/L1616M11 16 16 150 12 16 16 0.4 TC**1102... 0.9
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamping screw Wrench
JTTACL0810K08 JCP-1 JDS-3525 P-2F
JTTACR/L**M11 JCP-2 JDS-3525 P-2F

Reference pages
JSTACR/L, JTTACR/L: Inserts → B133 -, PCD → B179

B370 www.tungaloyamerica.com
J SV J2B R /L
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 3 ° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s

Without offset

b
f
L2 L1
50°
93°

h1

h
Cutting edge style J2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSVJ2BR/L062 0.375 0.375 5.000 0.780 0.375 0.375 0.008 VB**22... 0.89
JSVJ2BR/L082 0.500 0.500 5.000 0.780 0.500 0.500 0.008 VB**22... 0.89
JSVJ2BR/L102 0.625 0.625 5.000 0.780 0.625 0.625 0.008 VB**22... 0.89

Metric h b L1 L2 h1 f rε** Insert Torque*

JSVJ2BR/L1010X11 10 10 120 21 10 10 0.2 VB**1103... 1.2
JSVJ2BL1010K11 10 10 125 21 10 10 0.2 VB**1103... 1.2

Miniature Tool
JSVJ2BR/L1212F11 12 12 85 21 12 12 0.2 VB**1103... 1.2
JSVJ2BR/L1212X11 12 12 120 21 12 12 0.2 VB**1103... 1.2
JSVJ2BR1212K11 12 12 125 21 12 12 0.2 VB**1103... 1.2
JSVJ2BR/L1616X11 16 16 120 21 16 16 0.2 VB**1103... 1.2
*Torque: Recommended torque (lbf∙ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSVJ2BR/L... CSTB-2.5 T-8F

J SV JB R /L
S c re w - o n to o l h o l d e r w i t h 9 3 ° a p p ro a c h a n g l e f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s
b
f

L2
50° L1
93°
h1

Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSVJBR/L1010H11 10 10 100 20 10 12 0.016 VB**1103... 1.2
JSVJBR/L1212H11 12 12 100 22 12 16 0.016 VB**1103... 1.2
JSVJBR/L1616H11 16 16 100 22 16 20 0.016 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSVJBR/L... CSTB-2.5 T-8F

Reference pages
JSVJ2BR/L, JSVJBR/L: Inserts → B147 -, CBN → B171 -

Tungaloy B371
 JS VJ2B R /L- CHP
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 9 3° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s ,
w i t h c h a n n e l s f o r hi g h p ressure co o l ant

L1 Without offset

b
50°

f2
L2
93°

h
h1
Cutting edge style J2 5/16”-24UNF Right hand (R) shown.

Inch h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2BR/L082-CHP 0.500 0.500 3.344 0.930 0.500 0.500 0.610 0.008 VB**22... 0.9

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSVJ2BR/L1212F11-CHP 12 12 85 23.6 12 12 14.7 0.2 VB**1103... 1.2

*Torque: Recommended torque (lbf∙ft, N∙m) for clamping

**rε: Standard corner radius
Miniature Tool

SPARE PARTS
Designation Clamping screw Coolant unit Wrench
JSVJ2BR/L**-CHP CSTB-2.5 S-CU-CHP T-8F

JS VAB R /L
Sc re w -o n to o l ho l d er w i t ho ut o f f set w i t h 9 1° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s

Without offset

b
f

50°
L2 L1
91°
h1

Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JSVABR/L1010K11 10 10 125 21 10 10 0.2 VB**1103... 1.2
JSVABL1212K11 12 12 125 21 12 12 0.2 VB**1103... 1.2
JSVABL1616K11 16 16 125 21 16 16 0.2 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSVABR/L... CSTB-2.5 T-8F

Reference pages
JSVJ2BR/L-CHP, JSVABR/L: Inserts → B147 -, CBN → B171 -

B372 www.tungaloyamerica.com
J SV JB R -F
S c re w -o n s te p p e d - head to o l ho l d er w i t h 9 3 ° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s

L1
L3

b
f2
93° 50° L2

h1

h
L4

Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 L3 L4 h1 f f2 rε** Insert Torque*

JSVJBR1216F11-F15 12 16 85 12.6 27 21 12 15 26 0.2 VB**1103... 1.2
JSVJBR1216X11-F15 12 16 120 12.6 27 21 12 15 26 0.2 VB**1103... 1.2
JSVJBR1620X11-F15 16 20 120 12.6 27 21 16 15 26 0.2 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS

Miniature Tool
Designation Clamping screw Wrench
JSVJBR**-F15 CSTB-2.5 T-8F

Reference pages
JSVJBR-F: Inserts → B147 -, CBN → B171 -

Tungaloy B373
 JS VN B N
S c re w - o n to o l h o l d e r w i t h 7 2 . 5 ° a p p ro a c h a n g l e f o r p o s i t i v e 3 5 ° r h o m b i c i n s e r t s

L1

b
L2

f
72.5°

h1

h
Cutting edge style N
Metric h b L1 L2 h1 f rε** Insert Torque*
JSVNBN1010X11 10 10 120 22 10 5 0.2 VB**1103... 1.2
JSVNBN1212F11 12 12 85 22 12 6 0.2 VB**1103... 1.2
JSVNBN1212X11 12 12 120 22 12 6 0.2 VB**1103... 1.2
JSVNBN1616X11 16 16 120 22 16 8 0.2 VB**1103... 1.2

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius
Miniature Tool

SPARE PARTS
Designation Clamping screw Wrench
JSVNBN... CSTB-2.5 T-8F

Reference pages
JSVNBN: Inserts → B147 -, CBN → B171 -

B374 www.tungaloyamerica.com
J SV L2PR /L
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 9 5 ° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s

Without offset

b
f
45°
L2
L1
95°

h1

h
Cutting edge style L2 Right hand (R) shown.

Inch h b L1 L2 h1 f rε** Insert Torque*

JSVL2PR/L082 0.500 0.500 5.000 18.000 0.500 0.500 0.008 VP**63... 0.89
JSVL2PR/L102 0.625 0.625 5.000 20.000 0.625 0.625 0.008 VP**63... 0.89

Metric h b L1 L2 h1 f rε** Insert Torque*

JSVL2PR/L1010X08 10 10 120 16 10 10 0.2 VP**0802... 0.6
JSVL2PR/L1010K08 10 10 125 16 10 10 0.2 VP**0802... 0.6
JSVL2PR/L1212F08 12 12 85 16 12 12 0.2 VP**0802... 0.6
JSVL2PR/L1212F11 12 12 85 21 12 12 0.2 VP**1103... 1.2
JSVL2PR/L1212X08 12 12 120 16 12 12 0.2 VP**0802... 0.6

Miniature Tool
JSVL2PR/L1212X11 12 12 120 21 12 12 0.2 VP**1103... 1.2
JSVL2PR/L1212K08 12 12 125 16 12 12 0.2 VP**0802... 0.6
JSVL2PR/L1616X08 16 16 120 16 16 16 0.2 VP**0802... 0.6
JSVL2PL1616K08 16 16 125 16 16 16 0.2 VP**0802... 0.6
JSVL2PR/L1616X11 16 16 120 21 16 16 0.2 VP**1103... 1.2
*Torque: Recommended torque (lbf∙ft, N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSVL2PR/L082/102 CSTB-2L T-8F
JSVL2PR/L**08 CSTB-2L T-6F
JSVL2PR/L**11 CSTB-2.5 T-8F

J SV P2P R /L
S c re w -o n to o l h o l d er w i t ho ut o f f set w i t h 1 1 7. 5° a p p roa c h a n gl e f or p os i t i v e 35° r h om b i c i n s e r t s
f2

Without offset
b
f

L2
L1
117.5°
h1

Cutting edge style P2 Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

JSVP2PR/L1010K08 10 10 125 16 10 10 4 0.2 VP**0802... 0.6
JSVP2PR/L1010K11 10 10 125 20 10 10 8 0.2 VP**1103... 1.2
JSVP2PR/L1212K08 12 12 125 16 12 12 2 0.2 VP**0802... 0.6
JSVP2PR/L1212K11 12 12 125 20 12 12 6 0.2 VP**1103... 1.2
JSVP2PR/L1616K08 16 16 125 16 16 16 2 0.2 VP**0802... 0.6
JSVP2PR/L1616K11 16 16 125 20 16 16 6 0.2 VP**1103... 1.2
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamping screw Wrench
JSVP2PR/L**08 CSTB-2L T-6F
JSVP2PR/L**11 CSTB-2.5 T-8F

Reference pages
JSVL2PR/L, JSVP2PR/L: Inserts → B151

Tungaloy B375
 P C LN R
Le v e r l o c k t y pe to o l ho l d er w i t h 9 5 º ap p ro a c h a n gl e f or n e ga t i v e 80º r h om b i c i n s e r t s

95°

b
f
f2
L2
L1
95°

h1

h
Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PCLNR2020H12 20 20 100 26 20 25 18 0.8 CN**1204... 3

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Lever Spring pin Wrench
PCLNR2020H12 LSC42 LCS4 LCL4 LSP4 P-3
Miniature Tool

P C L2N R
Le v e r l o c k t y pe to o l ho l d er w i t ho ut o f f set w i t h 95º a p p roa c h a n gl e f or n e ga t i v e 80º r h om b i c i n s e r ts

95° Without offset

b
f
L2
95° h1 L1

h
Cutting edge style L2 Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

PCL2NR2020H12 20 20 100 26 20 20 0.8 CN**1204... 3

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Lever Spring pin Wrench
PCL2NR2020H12 LSC42 LCS4 LCL4 LSP4 P-3

P D JN R
Le v e r l o c k t y pe to o l ho l d er w i t h 9 3 º ap p ro a c h a n gl e f or n e ga t i v e 55º r h om b i c i n s e r t s
b
f2
f

30˚
L2
L1
93°
h1

Cutting edge style J Right hand (R) shown.

Metric h b L1 L2 h1 f f2 rε** Insert Torque*

PDJNR2020H15 20 20 100 32 20 25 20 0.8 DN**1504... 3

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Lever Spring pin Wrench
PDJNR2020H15 LSD42 LCS4 LCL4 LSP4 P-3

Reference pages
PCLNR, PCL2NR: Inserts → B052 -, CBN → B165
PDJNR: Inserts → B063 -, CBN → B165

B376 www.tungaloyamerica.com
J TTA N R /L
B a c k c l a m p to o l ho l d er w i t ho ut o f f set w i t h 9 1º a p p roa c h a n gl e f or n e ga t i v e 60° t r i a n gu l a r i n s e r t s

Without offset

b
f
L2
L1
91°

h1

h
Cutting edge style A Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JTTANR/L1216K16 12 16 125 19.8 12 16 0.4 TN**1604... 1.2
JTTANR/L1616K16 16 16 125 19.8 16 16 0.4 TN**1604... 1.2
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamping screw Wrench
JTTANR/L... JCP-3N JDS-5040 P-2.5F

Miniature Tool
J T TLN R /L
B ac k c l a m p to o l h o l d er w i t ho ut o f f set w i t h 9 5 º a p p roa c h a n gl e f or n e ga t i v e 60° t r i a n gu l a r i n s e r t s

115° Without offset

b
f

L2
95° L1
h1

h
Cutting edge style L Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

JTTLNR/L1216F16 12 16 85 17 12 16 0.4 TN**1604... 1
JTTLNR/L1216X16 12 16 120 17 12 16 0.4 TN**1604... 1
JTTLNR/L1616X16 16 16 120 17 16 16 0.4 TN**1604... 1

*Torque: Recommended torque (N∙m) for clamping

**rε: Standard corner radius

SPARE PARTS
Designation Clamp Clamping screw Wrench
JTTLNR/L... JCP-3N JDS-5040 P-2.5F

Reference pages
JTTANR/L, JTTLNR/L: Inserts → B082 -, CBN → B166 -, PCD → B178 -

Tungaloy B377
 PTL2N R /L
Le v e r l o c k t y p e to o l ho l d er w i t ho ut o f f set w i t h 95º a p p roa c h a n gl e f or n e ga t i v e 60° t r i a n gu l a r i n s er ts

115° Without offset

b
f
L2
95° L1

h1

h
Cutting edge style L2 Right hand (R) shown.

Metric h b L1 L2 h1 f rε** Insert Torque*

PTL2NR/L2020H16 20 20 100 22 20 20 0.4 TN**1604... 2
*Torque: Recommended torque (N∙m) for clamping
**rε: Standard corner radius

SPARE PARTS
Designation Shim Clamping screw Lever Spring pin Wrench
PTL2NR/L2020H16 LST317 LCS3 LCL3 LSP3 P-2.5
Miniature Tool

PARTS FOR COOLANT HOSE

Connecting hose
Fig. 1 Fig. 2

Th Th1 Th1
L Th
L

Max. pressure
Metric
Designation L Th Th1 Fig.
(Mpa)
CHP-HOSE-G1/8-7/16-200BS 200 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-G1/8-7/16-250BS 250 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-5/16-7/16-200BS 200 5/16”-24UNF 7/16"-20 UNF 20 1
CHP-HOSE-5/16-G1/8-200BS 200 5/16”-24UNF G1/8"-28 BSPP 20 1
CHP-HOSE-G1/8-G1/8-200BB 200 G1/8"-28 BSPP G1/8"-28 BSPP 26 2
CHP-HOSE-G1/8-G1/8-250BB 250 G1/8"-28 BSPP G1/8"-28 BSPP 26 2

Connector for small lathe Seal washer

with seal washer

9 SW = 12
G1/8”-28 BSPP

6
ød
øD
11
4

25 ø13
W
5/16”-24 UNF

Metric
Designation Metric
Designation øD ød W
CHP-CONECTOR/5/16-G1/8 CHP-COPPER-SEAL1/8 15 10 1
CHP-COPPER-SEAL5/16 11 8 1
CHP-COPPER-SEAL5/16-2.5 11 8 2.5

Reference pages
PTL2NR/L: Inserts → B082 -, CBN → B166 -, PCD → B178 -

B378 www.tungaloyamerica.com
J S XG R /L
S c re w -o n to o l h ol d er w i t ho ut o f f set f o r f ro nt / re v e r s e t u r n i n g & ex te r n a l groov i n g

Max. ap
L3 Without offset

b
f
L1
L2 40°
C-type

h1

h
Front turning Reverse turning
Max. ap = 5.5 mm
Right hand (R) shown.

Metric h b L1 L2 L3 h1 f Insert
JSXGR/L1010K8-C 10 10 125 29 6.7 10 10 JXFR/L8... , JXRR/L8...
JSXGR/L1212K8-C 12 12 125 29 6.7 12 12 JXFR/L8... , JXRR/L8...
JSXGR/L1616K8 16 16 125 29 6.5 16 16 JXFR/L8... , JXRR/L8...
JSXGR/L2020K8 20 20 125 29 6.5 20 20 JXFR/L8... , JXRR/L8...
JSXGR/L2525K8 25 25 125 29 6.5 25 25 JXFR/L8... , JXRR/L8...
• Can be wrenched also from the back with a double-head screw.
• This toolholders can be used for JXF insert (front-turning), JXR insert (reverse-turning), JXG insert (grooving)

Miniature Tool
SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSXGR/L... CSTB-4SD T-8F (T-8L)

INSERT
J X F ( f ro n t t u r n ing , sharp ed g e)
6

T
ød rε
15˚
25

40˚
Right hand (R) shown.

Coated Uncoated Max.

rε J740 TH10 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L (mm)
JXFR/L8000F 0.03 䖃 䖃 8 3.97 5.5

JXFR/L8010F 0.1 䖃 䖃 8 3.97 5.5

䖃 : Line up

J X R ( re v e r s e t urning , sharp ed g e)
0.55 15˚
rε

60˚
25

ød T
Right hand (R) shown.

Coated Uncoated Max.

rε J740 TH10 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L (mm)
JXRR/L8000F 0.03 䖃 䖃 8 3.97 5.5

JXRR/L8010F 0.1 䖃 䖃 8 3.97 5.5

䖃 : Line up

Tungaloy B379
 JS X B R /L
Sc re w -o n to o l ho l d er f o r b ack t ur ni ng and t h re a d i n g

Max. ap
L3

b
f
L1
L2 40°
C-type

h1

h
Max. ap = 5.5 mm Right hand (R) shown.

Metric h b L1 L2 L3 h1 f Insert
JSXBR/L1010K8-C 10 10 125 29 6.7 10 5.7 JXBR/L8..., JXT*R...
JSXBR/L1212K8-C 12 12 125 29 6.7 12 7.7 JXBR/L8..., JXT*R...
JSXBR/L1616K8 16 16 125 29 6.4 16 11.7 JXBR/L8..., JXT*R...
JSXBR/L2020K8 20 20 125 29 6.4 20 15.7 JXBR/L8..., JXT*R...
JSXBR/L2525K8 25 25 125 29 6.4 25 20.7 JXBR/L8..., JXT*R...

• Can be wrenched also from the back with a double-head screw.

• This toolholders can be used for JXB insert (back-turning), JXT insert (threading)
Miniature Tool

SPARE PARTS
Designation Clamping screw Wrench
JSXBR/L... CSTB-4SD T-8F

INSERT
J X B ( s h a r p ed g e)
ød T
15˚ rε

60˚

40˚
Right hand (R) shown.

Coated Uncoated Max.

rε J740 TH10 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L (mm)
JXBR/L8000F 0.03 䖃 䖃 䖃 䖃 8 3.97 5.5

JXBR/L8005F 0.05 䖃 䖃 䖃 䖃 8 3.97 5.5

JXBR/L8010F 0.1 䖃 䖃 䖃 䖃 8 3.97 5.5

JXBR/L8015F 0.15 䖃 䖃 䖃 䖃 8 3.97 5.5

䖃 : Line up

J X B ( w i t h ho rning )
ød T
15˚ rε

60˚

40˚
Right hand (R) shown.

Coated Max.
rε J740 ød T depth
Designation (mm) (mm) (mm) of cut
R L (mm)
JXBR/L8005 0.05 䖃 䖃 8 3.97 5.5

JXBR/L8010 0.1 䖃 䖃 8 3.97 5.5

JXBR/L8015 0.15 䖃 䖃 8 3.97 5.5

䖃 : Line up

B380 www.tungaloyamerica.com
J STB R /L
S c re w -o n to o l h o l d er f o r b ack t ur ni ng

L3

Max. ap

b
L1

f
L2

h1

h
h2
Max. ap = 2.5 mm
Right hand (R) shown.

Inch h b L1 L2 L3 h1 f h2 Insert Torque*

JSTBR/L063 0.375 0.375 5.000 0.625 0.197 0.375 0.218 0.250 JTBR/L3... 0.89
JSTBR/L083 0.500 0.500 5.000 0.625 0.197 0.500 0.312 0.125 JTBR/L3... 0.89
JSTBR/L103 0.625 0.625 5.000 0.625 0.197 0.625 0.468 - JTBR/L3... 0.89

Metric h b L1 L2 L3 h1 f h2 Insert Torque*

JSTBR/L1010X3 10 10 120 15 5 10 6 5 JTBR/L3... 1.2
JSTBL1010K3 10 10 125 15 5 10 6 5 JTBR/L3... 1.2

Miniature Tool
JSTBR/L1212F3 12 12 85 15 5 12 8 3 JTBR/L3... 1.2
JSTBR/L1212X3 12 12 120 15 5 12 8 3 JTBR/L3... 1.2
JSTBR/L1616X3 16 16 120 15 5 16 12 - JTBR/L3... 1.2
*Torque: Recommended torque (lbf∙ft, N∙m) for clamping

SPARE PARTS
Designation Clamping screw Wrench
JSTBR/L... CSTB-4SD T-8F

J S-TB L3
S c re w -o n to o l h o l d er f o r b ack t ur ni ng
Max. ap

L1
2
ø3

25
øDs
L3

L2
f

h
B

Max. ap = 2.5 mm

Metric øDs f L1 L2 L3 h B Insert Torque*

JS19K-TBL3 19.05 6 125 17 4.5 18 11.5 JTBR3... 3
JS20K-TBL3 20 6 125 17 4.5 19 11.5 JTBR3... 3
JS22K-TBL3 22 6 125 17 4.5 21 11.5 JTBR3... 3
JS25K-TBL3 25.4 10 125 17 4.5 24 12.7 JTBR3... 3

*Torque: Recommended torque (N∙m) for clamping

SPARE PARTS
Designation Clamping screw Wrench
JS**-TBL3 CSTB-4S T-15F

Reference pages
JSTBR/L, JS-TBL3: Inserts → B382, Standard cutting conditions → B382

Tungaloy B381
 INSERT
J T B ( s h a r p ed g e)
2°
rε
15°

3.5
45°

ød T
Right hand (R) shown.

Coated Cermet Uncoated Max.

rε J740 SH725 NS9530 TH10 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L R L R L (mm)
JTBR/L3000F 0.03 䖃 䖃 䖃 䖃 䖃 䖃 9.438 3.18 2.5

JTBR/L3005F 0.05 䖃 䖃 䖃 䖃 䖃 䖃 9.438 3.18 2.5

JTBR/L3010F 0.1 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.438 3.18 2.5

JTBR/L3015F 0.15 䖃 䖃 䖃 9.438 3.18 2.5

䖃 : Line up
J T B ( w i t h h o rning )
Miniature Tool

2°
rε
15°
3.5

45°

ød T
Right hand (R) shown.

Coated Coated cermet Max.

rε J740 J9530 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L (mm)
JTBR/L3005 0.05 䖃 䖃 䖃 9.438 3.18 2.5

JTBR/L3010 0.1 䖃 䖃 䖃 9.438 3.18 2.5

䖃 : Line up

STA N DA RD CUT T ING CONDIT IO N S ( JT B t yp e in se r t )

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
SH725 164 - 656 0.000 - 0.004

J740 33 - 328 0.000 - 0.004

General steel
1045, etc.
NS9530 164 - 492 0.000 - 0.004

J9530 164 - 492 0.000 - 0.004

SH725 164 - 656 0.000 - 0.004

Free-cutting steel
J740 33 - 328 0.000 - 0.004

SH725 164 - 656 0.000 - 0.004

J740 33 - 328 0.000 - 0.004

Stainless steel
303, etc.
NS9530 164 - 492 0.000 - 0.004

J9530 164 - 492 0.000 - 0.004

Aluminum alloys, Brass

TH10 33 - 656 0.000 - 0.004
5056, 6061, etc.

Difficult-to-machine material, Titanium alloys

TH10 33 - 98 0.000 - 0.004
Ti-6AI-4V, etc.

B382 www.tungaloyamerica.com
J SEG R /L
S c re w -o n to o l h o l d er f o r b ack t ur ni ng

L3

b
Max. ap

f
L2
L1

h1

h
Max. ap = 3 mm
Right hand (R) shown.

Metric h b L1 L2 L3 h1 f Insert Torque*

JSEGR/L1010K10 10 10 125 - 3.3 10 7.5 J10ER/L... 1.2
JSEGR/L1212K10 12 12 125 - 3.3 12 9.5 J10ER/L... 1.2
JSEGR/L1616K10 16 16 125 - 3.3 16 13.5 J10ER/L... 1.2

*Torque: Recommended torque (N∙m) for clamping

SPARE PARTS
Designation Clamping screw Wrench

Miniature Tool
JSEGR/L... CSTB-2.5 T-8F

INSERT
J 1 0 E ( s h a r p ed g e)
0.5 rε
30°
3.3

60°

ød T
Right hand (R) shown.

Coated Cermet Uncoated Max.

rε J740 SH725 NS9530 TH10 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L R L R L (mm)
J10ER/L005BF 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 6.35 3.18 3

J10ER/L010BF 0.1 䖃 䖃 䖃 䖃 䖃 䖃 䖃 6.35 3.18 3

J10ER/L015BF 0.15 䖃 䖃 6.35 3.18 3

䖃 : Line up

J 1 0 E ( w i t h h o rning )
0.5 rε
30°
3.3

60°

ød T
Right hand (R) shown.

Coated Coated cermet Max.

rε J740 J9530 ød T depth
Designation (mm) (mm) (mm) of cut
R L R L (mm)
J10ER/L005B 0.05 䖃 䖃 䖃 6.35 3.18 3

J10ER/L010B 0.1 䖃 䖃 䖃 6.35 3.18 3

䖃 : Line up

Reference pages
JSEGR/L: Inserts → B383 -, Standard cutting conditions → B384

Tungaloy B383
 STA N DA RD CUT T ING CONDIT IO N S ( J1 0 E t yp e in se r t )

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
SH725 164 - 656 0.000 - 0.004

J740 33 - 328 0.000 - 0.004

General steel
1045, etc.
NS9530 164 - 492 0.000 - 0.004

J9530 50 - 150 0.000 - 0.004

SH725 164 - 656 0.000 - 0.004

Free-cutting steel
J740 33 - 328 0.000 - 0.004

SH725 164 - 656 0.000 - 0.004

J740 33 - 328 0.000 - 0.004

Stainless steel
303, etc.
NS9530 164 - 492 0.000 - 0.004

J9530 164 - 492 0.000 - 0.004

Aluminum alloys, Brass

TH10 33 - 656 0.000 - 0.004
5056, 6061, etc.
Miniature Tool

Difficult-to-machine material, Titanium alloys

TH10 33 - 98 0.000 - 0.004
Ti-6AI-4V, etc.

INSERT
1 0 E ( I n s e r t b lank) 1 0 E (Inse r t bla nk )
W

6.35

ø3.0
6.35

ø3.0

26° 13.3 3.18

3.0

5°
A

13.0 3.18

Right hand (R) shown. Right hand (R) shown.

Uncoated Uncoated
TH10 W A TH10
Designation Designation
(mm) (mm)
R L R L
10ER/L100B 䖃 䖃 1 2.5 10ER/L300 䖃 䖃

10ER/L150B 䖃 䖃 1.5 3
䖃 : Line up
Note: Right hand holder (JSEGR...) use right hand insert (10ER...)
䖃 : Line up
and left hand holder (JSEGL...) use left hand insert (10EL...).
Note: Right hand holder (JSEGR...) use right hand insert (10ER...)
and left hand holder (JSEGL...) use left hand insert (10EL...).

Formed examples of insert blanks Standard cutting conditions

Workpiece material Carbon Stainless Brass
Front turning

Operations
Back turning

steels steels
Threading

Grooving

Cutting speed (sfm) ~ 330 ~ 160 ~ 650

Lateral feed Roughing ~ 0.002 ~ 0.001 ~ 0.004
(external turning) Feed (ipr) Medium ~ 0.001 ~ 0.001 ~ 0.002
Notes: Finishing ~ 0.0007 ~ 0.0006 ~ 0.004
Parting-off

• Front relief angle, side relief

angle, edge width can be ground Cutting speed (sfm) ~ 260 ~ 100 ~ 500
depending on the application. Parting-off Roughing ~ 0.0007 ~ 0.0006 ~ 0.002
• Insert blanks can be formed to a Grooving
Forming Feed (ipr) Medium ~ 0.0006 ~ 0.0004 ~ 0.001
profiling tool which has a width up to
0.118". Finishing ~ 0.0004 ~ 0.0003 ~ 0.0006

B384 www.tungaloyamerica.com
MEMO

Miniature Tool

Tungaloy B385
 I N I

JBT R /L
So l i d b o r i n g b ar s f o r b o r i ng , p ro f i l i ng & ch a m f e r i n g

L1
øDm
8º

øDsh6
T max

a
98° L2

f
rε

20º
Details of edge
Right hand (R) shown.

+
Metric SH730 øDm øDs f a L1 L2 T max rε 0.05
0
JBTR04020004-D006 䖃 0.6 4 - 0.5 18.5 2 0.08 0.04
JBTR04030004-D006 䖃 0.6 4 - 0.5 19.5 3 0.08 0.04
JBTR04045005-D010 䖃 1 4 - 0.9 21 4.5 0.1 0.05
JBTR04065005-D010 䖃 1 4 - 0.9 23 6.5 0.1 0.05
JBTR04040005-D020 䖃 2 4 - 1.7 20.5 4 0.1 0.05
JBTR04090005-D020 䖃 2 4 - 1.7 25.5 9 0.1 0.05
JBTR04140005-D020 䖃 2 4 - 1.7 30.5 14 0.1 0.05
Miniature Tool

JBTR/L04090010-D028 䖃 3.5 4 0.6 2.6 25.5 9 0.2 0.1

JBTR/L04150010-D028 䖃 3.5 4 0.6 2.6 31.5 15 0.2 0.1
JBTR/L04190010-D028 䖃 3.5 4 0.6 2.6 35.5 19 0.2 0.1
JBTR/L04090010-D040 䖃 4 4 1.5 3.5 25.5 9 0.3 0.1
JBTR/L04150010-D040 䖃 4 4 1.5 3.5 31.5 15 0.3 0.1
JBTR/L04190010-D040 䖃 4 4 1.5 3.5 35.5 19 0.3 0.1
JBTR04230010-D040 䖃 4 4 1.5 3.5 39.5 23 0.3 0.1
JBTR04270010-D040 䖃 4 4 1.5 3.5 43.5 27 0.3 0.1
JBTR/L07090015-D050 䖃 5 7 0.9 4.4 25 9 0.5 0.15
JBTR/L07140015-D050 䖃 5 7 0.9 4.4 30 14 0.5 0.15
JBTR/L07190015-D050 䖃 5 7 0.9 4.4 35 19 0.5 0.15
JBTR/L07240015-D050 䖃 5 7 0.9 4.4 40 24 0.5 0.15
JBTR/L07290015-D050 䖃 5 7 0.9 4.4 45 29 0.5 0.15
JBTR07340015-D050 䖃 5 7 0.9 4.4 50 34 0.5 0.15
JBTR/L07140015-D060 䖃 6 7 1.8 5.3 30 14 0.5 0.15
JBTR/L07210015-D060 䖃 6 7 1.8 5.3 37 21 0.5 0.15
JBTR/L07240015-D060 䖃 6 7 1.8 5.3 40 24 0.5 0.15
JBTR/L07290015-D060 䖃 6 7 1.8 5.3 45 29 0.5 0.15
JBTR07340015-D060 䖃 6 7 1.8 5.3 50 34 0.5 0.15
JBTR07410015-D060 䖃 6 7 1.8 5.3 57 41 0.5 0.15
JBTR/L07190015-D068 䖃 6.8 7 2.8 6.3 35 19 0.6 0.15
JBTR07240015-D068 䖃 6.8 7 2.8 6.3 40 24 0.6 0.15
JBTR/L07290015-D068 䖃 6.8 7 2.8 6.3 45 29 0.6 0.15
JBTR/L07340015-D070 䖃 7 7 2.8 6.3 50 34 0.6 0.15
JBTR07390015-D070 䖃 7 7 2.8 6.3 55 39 0.6 0.15
JBTR07440015-D070 䖃 7 7 2.8 6.3 60 44 0.6 0.15
JBTR07490015-D070 䖃 7 7 2.8 6.3 65 49 0.6 0.15
䖃 : Line up

Reference pages
Standard cutting conditions → B393

B386 www.tungaloyamerica.com
 I N I

JBP R
S o l i d b o r i n g b a r s f o r b o r i ng & cham f er i ng

øDm L1

øDsh6
T max

a
90°
L2

f
rε 20º
Details of edge
Right hand (R) shown.

Metric SH730 øDm øDs f a L1 L2 T max rε+0.05

0
JBPR04090010-D028 䖃 3.5 4 0.9 2.6 25.5 9 0.2 0.1
JBPR04150010-D028 䖃 3.5 4 0.9 2.6 31.5 15 0.2 0.1
JBPR04090010-D040 䖃 4 4 1.5 3.5 25.5 9 0.3 0.1
JBPR04150010-D040 䖃 4 4 1.5 3.5 31.5 15 0.3 0.1
JBPR07140015-D050 䖃 5 7 0.9 4.4 30 14 0.5 0.15
JBPR07190015-D050 䖃 5 7 0.9 4.4 35 19 0.5 0.15
䖃 : Line up

Miniature Tool
I N I

JBU R
S o l i d b o r i n g b a r s f o r b ack b o r i ng & cham f eri n g

øDm L1
T max

øDsh6
a

45°
L2
f
8º

45º

w
t

Details of edge
Right hand (R) shown.

Metric SH730 øDm øDs f a L1 L2 t T max W +0.05

0
JBUR07140010-D050 䖃 5 7 0.9 4.4 30 14 0.2 1 1
JBUR07190010-D050 䖃 5 7 0.9 4.4 35 19 0.2 1 1
䖃 : Line up

I N I

JBC R
S o l i d b o r i n g b a r s f o r B o r i ng & 4 5 ° cham f er i n g

øDm L1
1
øDsh6
T max

45° L2
45°
f
º

45
45

rε
Details of edge
Right hand (R) shown.

Metric SH730 øDm øDs f a L1 L2 T max rε±0.05

JBCR07140020-D050 䖃 5 7 0.9 4.4 30 14 0.7 0.2
JBCR07190020-D050 䖃 5 7 0.9 4.4 35 19 0.7 0.2
JBCR07190020-D068 䖃 6.8 7 2.8 6.3 35 19 0.7 0.2
䖃 : Line up

Reference pages
Standard cutting conditions → B393

Tungaloy B387
 I N I

JB B R
So l i d b o r i n g b ar s f o r b ack b o r i ng

øDm L1

øDsh6
T max

a
f
30º L2

1.5
28° rε
Details of edge
Right hand (R) shown.

Metric SH730 øDm øDs f a L1 L2 T max rε+0.05

JBBR04140020-D030 䖃 3 4 0.6 2.6 30 14 0.5 0.2
JBBR04190020-D030 䖃 3 4 0.6 2.6 35 19 0.5 0.2
JBBR04140015-D040 䖃 4 4 1.5 3.5 30 14 0.8 0.15
JBBR04240015-D040 䖃 4 4 1.5 3.5 40 24 0.8 0.15
JBBR07190020-D050 䖃 5 7 0.9 4.4 35 19 1 0.2
JBBR07290020-D050 䖃 5 7 0.9 4.4 45 29 1 0.2
JBBR07190020-D060 䖃 6 7 1.8 5.3 35 19 1.8 0.2
Miniature Tool

JBBR07290020-D060 䖃 6 7 1.8 5.3 45 29 1.8 0.2

JBBR07190020-D070 䖃 7 7 2.8 6.3 35 19 2.5 0.2
JBBR07290020-D070 䖃 7 7 2.8 6.3 45 29 2.5 0.2
䖃 : Line up

I N I

JB I R
So l i d b o r i n g b ar s f o r t hread i ng ( m et r i c)

øDm L1
Y

øDsh6
a

60º
L2
f
t

W2
Details of edge
Right hand (R) shown.

Metric SH730 Pitch øDm W2- 00.02 øDs f a L1 L2 t Y

JBIR04140050-D040 䖃 0.5 4 0.06 4 1.5 3.5 30 14 0.3 0.35
JBIR07140050-D050 䖃 0.5 5 0.06 7 0.9 4.4 30 14 0.3 0.35
JBIR07140075-D050 䖃 0.75 5 0.09 7 0.9 4.4 30 14 0.4 0.45
JBIR07140100-D048 䖃 1 4.8 0.12 7 0.9 4.4 30 14 0.6 0.55
JBIR07140100-D060 䖃 1 6 0.12 7 1.8 5.3 30 14 0.6 0.55
JBIR07140125-D060 䖃 1.25 6 0.15 7 1.8 5.3 30 14 0.7 0.65
JBIR07140150-D060 䖃 1.5 6 0.18 7 1.8 5.3 30 14 0.8 0.75
JBIR07140150-D070 䖃 1.5 7 0.18 7 2.8 6.3 30 14 0.8 0.75
䖃 : Line up

Reference pages
Standard cutting conditions → B393

B388 www.tungaloyamerica.com
 I N I

J B G R /L
S o l i d b o r i n g b a r s f o r i nter nal g ro o v i ng

øDm L1

T max

øDsh6
a
L2

f
W
Details of edge Right hand (R) shown.

+ 0.05
Metric SH730 W 0 øDm øDs f a L1 L2 T max
JBGR04050050-D020 䖃 0.5 2 4 0.2 1.8 21 5 0.4
JBGR04100050-D020 䖃 0.5 2 4 0.2 1.8 26 10 0.4
JBGR04050070-D030 䖃 0.7 3 4 0.7 2.7 21 5 0.6
JBGR04100070-D030 䖃 0.7 3 4 0.7 2.7 26 10 0.6
JBGR04090100-D040 䖃 1 4 4 1.5 3.5 25.5 9 0.8
JBGR04150100-D040 䖃 1 4 4 1.5 3.5 31.5 15 0.8
JBGR07090100-D050 䖃 1 5 7 0.9 4.4 25 9 1

Miniature Tool
JBGR07140100-D050 䖃 1 5 7 0.9 4.4 30 14 1
JBGR07090150-D050 䖃 1.5 5 7 0.9 4.4 25 9 1
JBGR07140150-D050 䖃 1.5 5 7 0.9 4.4 30 14 1
JBGR07090200-D050 䖃 2 5 7 0.9 4.4 25 9 1
JBGR07190200-D050 䖃 2 5 7 0.9 4.4 35 19 1
JBGR/L07090100-D060 䖃 1 6 7 1.8 5.3 25 9 1.8
JBGR07140100-D060 䖃 1 6 7 1.8 5.3 30 14 1.8
JBGR07210100-D060 䖃 1 6 7 1.8 5.3 37 21 1.8
JBGR07290100-D060 䖃 1 6 7 1.8 5.3 45 29 1.8
JBGR/L07090150-D060 䖃 1.5 6 7 1.8 5.3 25 9 1.8
JBGR07140150-D060 䖃 1.5 6 7 1.8 5.3 30 14 1.8
JBGR07210150-D060 䖃 1.5 6 7 1.8 5.3 37 21 1.8
JBGR07240150-D060 䖃 1.5 6 7 1.8 5.3 40 24 1.8
JBGR07290150-D060 䖃 1.5 6 7 1.8 5.3 45 29 1.8
JBGR07090200-D060 䖃 2 6 7 1.8 5.3 25 9 1.8
JBGR07140200-D060 䖃 2 6 7 1.8 5.3 30 14 1.8
JBGR07210200-D060 䖃 2 6 7 1.8 5.3 37 21 1.8
JBGR07240200-D060 䖃 2 6 7 1.8 5.3 40 24 1.8
JBGR07290200-D060 䖃 2 6 7 1.8 5.3 45 29 1.8
JBGR07090100-D068 䖃 1 6.8 7 2.7 6.2 25 9 2.5
JBGR07140100-D068 䖃 1 6.8 7 2.7 6.2 30 14 2.5
JBGR07210100-D068 䖃 1 6.8 7 2.7 6.2 37 21 2.5
JBGR07090150-D068 䖃 1.5 6.8 7 2.7 6.2 25 9 2.5
JBGR07140150-D068 䖃 1.5 6.8 7 2.7 6.2 30 14 2.5
JBGR07210150-D068 䖃 1.5 6.8 7 2.7 6.2 37 21 2.5
JBGR07290150-D068 䖃 1.5 6.8 7 2.7 6.2 45 29 2.5
JBGR07090200-D068 䖃 2 6.8 7 2.7 6.2 25 9 2.5
JBGR/L07140200-D068 䖃 2 6.8 7 2.7 6.2 30 14 2.5
JBGR07210200-D068 䖃 2 6.8 7 2.7 6.2 37 21 2.5
JBGR07250200-D068 䖃 2 6.8 7 2.7 6.2 40 25 2.5
JBGR07290200-D068 䖃 2 6.8 7 2.7 6.2 45 29 2.5
* Corner radius : less than 0.004". 䖃 : Line up

Reference pages
Standard cutting conditions → B394

Tungaloy B389
 I N I

JB F R /L
So l i d b o r i n g b ar s f o r f ace g ro o v i ng

øDm L1

øDsh6
a
T max
L2

W
Details of edge
Right hand (R) shown.

+ 0.05
Metric SH730 W 0 øDm øDs a L1 L2 T max
JBFR07110100-D060 䖃 1 6 7 5.2 26 10 1.5
JBFR07110150-D060 䖃 1.5 6 7 5.2 26 10 2
JBFR07110200-D060 䖃 2 6 7 5.2 26 10 3
JBFR07110100-D080 䖃 1 8 7 5.9 27 11 1.5
JBFR07110150-D080 䖃 1.5 8 7 5.9 27 11 2.5
JBFR07110200-D080 䖃 2 8 7 5.9 27 11 3
JBFR07110250-D080 䖃 2.5 8 7 5.9 27 11 3.5
Miniature Tool

JBFR07110300-D080 䖃 3 8 7 5.9 27 11 3.5

JBFR/L07210150-D080 䖃 1.5 8 7 5.9 36 21 2.5
JBFR07210200-D080 䖃 2 8 7 5.9 36 21 3
JBFR07210250-D080 䖃 2.5 8 7 5.9 36 21 3.5
JBFR07210300-D080 䖃 3 8 7 5.9 36 21 3.5
JBFR/L07300200-D080 䖃 2 8 7 5.9 46 30 3
JBFR07300300-D080 䖃 3 8 7 5.9 46 30 3.5
JBFR07200200-D080 䖃 2 8 7 5.9 36 20 3
JBFR07200250-D150 䖃 2.5 15 7 5.9 36 20 20
JBFR07200300-D150 䖃 3 15 7 5.9 36 20 20
JBFR07300300-D150 䖃 3 15 7 5.9 46 30 30
* Corner radius : less than 0.004". 䖃 : Line up

I N I

JB S R
So l i d b o r i n g b ar s f o r f ace g ro o v i ng ( f o r sh a f t m a c h i n i n g)

L1

øDsh6
a

T max
L2
W

øDm

Details of edge
Right hand (R) shown.

Metric SH730 W+0.05

0 øDm øDs a L1 L2 T max
JBSR07200200-D060 䖃 2 6 7 5.2 36 20 4
* Corner radius : less than 0.004". 䖃 : Line up

Reference pages
Standard cutting conditions → B394

B390 www.tungaloyamerica.com
 I N I

JBR R
S o l i d b o r i n g b a r s f o r B o r i ng & p ro f i l i ng ( f ul l ra d i u s t y p e )

øDm L1

T max

øDsh6
a
f
L2
R
w
Details of edge
Right hand (R) shown.
+ 0.05
Metric SH730 W 0 øDm øDs f a L1 L2 T max R
JBRR07190050-D050 䖃 1 5 7 0.9 4.4 35 19 1 0.5
JBRR07240050-D060 䖃 1 6 7 1.8 5.3 40 24 1.8 0.5
JBRR07290050-D068 䖃 1 6.8 7 2.8 6.3 45 29 2.5 0.5
䖃 : Line up

I N I

JBBS

Miniature Tool
S le e v e f o r ex te r nal co o l ant sup p l y

øDo L1

T
L2 L3
øDi1

øDi2
Metric øDo øDi1 øDi2 L1 L2 L3 T
JBBS12-4-4 12 4 4 75 10 55 10.3
JBBS127-4-4 12.7 (0.500") 4 4 76.2 10 56.2 11.6
JBBS14-4-4 14 4 4 75 10 55 12
JBBS159-4-7 15.875 (0.625") 4 7 76.2 10 56.2 14
JBBS16-4-7 16 4 7 75 10 55 15
JBBS19-4-7 19.05 (0.750") 4 7 89 10 69 17.2
JBBS20-4-7 20 4 7 90 10 70 18
JBBS22-4-7 22 4 7 90 10 70 20
JBBS25-4-7 25 4 7 100 10 80 23
JBBS254-4-7 25.4 (1.000") 4 7 90 10 70 23.4

SPARE PARTS
Designation Clamping screw Wrench
JBBS12-4-4 SSHM5-4PF-S P-2.5
JBBS127-4-4 SSHM5-6PF-S P-2.5
JBBS14-4-4 SSHM5-4PF-S P-2.5
JBBS**-4-7 SSHM5-6PF-S P-2.5

Reference pages
Standard cutting conditions → B393

Tungaloy B391
 I N I

JB B S -C
Sl e e v e f o r i n ter nal co o l ant sup p l y

øDo1 øDo1

øDo22

øDo22
L1 L T L1 L T

øDi11

THD

THD
øDi11
16 Fig.
Fig.11 12 Fig.
Fig.22

Metric øDo1 øDo2 øDi1 L L1 T THD Fig.

JBBS159-4-L100C 15.875 (0.625") 15.875 4 100 10 14.58 R1/8 1
JBBS159-7-L100C 15.875 (0.625") 15.875 7 100 10 14.58 R1/8 1
JBBS16-4-L100C 16 16 4 100 10 15 R1/8 1
JBBS16-7-L100C 16 16 7 100 10 15 R1/8 1
JBBS19-4-L100C 19.05 (0.750") 17.5 4 100 20 17.2 R1/8 2
JBBS19-7-L100C 19.05 (0.750") 17.5 7 100 20 17.2 R1/8 2
JBBS20-4-L100C 20 17.5 4 100 20 18 R1/8 2
Miniature Tool

JBBS20-7-L100C 20 17.5 7 100 20 18 R1/8 2

JBBS22-4-L100C 22 17.5 4 100 20 20 R1/8 2
JBBS22-7-L100C 22 17.5 7 100 20 20 R1/8 2
JBBS25-4-L100C 25 18 4 100 23 23 R1/8 2
JBBS25-7-L100C 25 18 7 100 23 23 R1/8 2
JBBS254-4-L100C 25.4 18 4 100 23 23.4 R1/8 2
JBBS254-7-L100C 25.4 18 7 100 23 23.4 R1/8 2

SPARE PARTS
Designation Clamping screw Wrench
JBBS**-4-L100C SSHM5-6PF-S P-2.5
JBBS**-7-L100C SSHM5-4PF-S P-2.5

B392 www.tungaloyamerica.com
 STA N DA R D CUT T ING CONDIT IONS

Boring, profiling, chamfering, back boring

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
Low carbon steels
1015, 1025, etc.
SH730 300 (130 - 460) 0.002 (0.0004 - 0.003) (*)

Carbon steels, Alloy steels

1055, 4140, etc.
SH730 300 (130 - 460) 0.002 (0.0004 - 0.003) (*)

Prehardened steels SH730 300 (130 - 460) 0.002 (0.0004 - 0.003) (*)
NAK80, PX5, etc.

Stainless steels SH730 300 (130 - 460) 0.002 (0.0004 - 0.003) (*)
304, 316, etc.

Grey cast irons SH730 200 (100 - 330) 0.002 (0.0004 - 0.003) (*)
No.250B, No.300B, etc.

Ductile cast irons SH730 200 (100 - 330) 0.002 (0.0004 - 0.003) (*)
65-45-12, 80-55-06, etc.

Aluminum alloys, copper alloys

SH730 490 (300 - 660) 0.002 (0.0004 - 0.003) (*)

Miniature Tool
Si < 12%

Titanium alloys
SH730 200 (100 - 330) 0.002 (0.0004 - 0.003) (*)
Ti-6AI-4V, etc.

Superalloys
Inconel718, etc.
SH730 200 (100 - 330) 0.002 (0.0004 - 0.003) (*)

* JBTR/L04020004-D006,
JBTR/L04030004-D006
Max. f = 0.01 mm/rev

Threading (metric thread)

Cutting Number of passes

ISO Workpiece material Grade speed Pitch (mm)
Vc (sfm) 0.5 (0.020") 0.75 (0.029") 1.0 (0.039") 1.25 (0.049") 1.5 (0.059")
Low carbon steels SH730 460 6-8 8 - 10 10 - 12 12 - 15 15 - 18
1015, 1025, etc.

Carbon steels, Alloy steels

SH730 460 6-8 8 - 10 10 - 12 12 - 15 15 - 18
1055, 4140, etc.

Prehardened steels SH730 460 6-8 8 - 10 10 - 12 12 - 15 15 - 18

NAK80, PX5, etc.

Stainless steels SH730 8 10 12 15 18

340
304, 316, etc.

Grey cast irons

No.250B, No.300B, etc. SH730 380 7 9 12 14 17

Ductile cast irons

SH730 380 7 9 12 14 17
65-45-12, 80-55-06, etc.

Aluminum alloys, copper alloys

Si < 12% SH730 1150 6 8 10 12 15

Tungaloy B393
 STA N DA RD CUT T ING CONDIT IO N S

Internal grooving

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
Low carbon steels
1015, 1025, etc.
SH730 300 (130 - 460) 0.0008 (0.0004 - 0.0012)

Carbon steels, Alloy steels

1055, 4140, etc.
SH730 300 (130 - 460) 0.0008 (0.0004 - 0.0012)

Prehardened steels SH730 300 (130 - 460) 0.0008 (0.0004 - 0.0012)

NAK80, PX5, etc.

Stainless steels SH730 300 (130 - 460) 0.0008 (0.0004 - 0.0012)

304, 316, etc.

Grey cast irons SH730 200 (100 - 330) 0.0008 (0.0004 - 0.0012)
No.250B, No.300B, etc.

Ductile cast irons SH730 200 (100 - 330) 0.0008 (0.0004 - 0.0012)
65-45-12, 80-55-06, etc.

Aluminum alloys, copper alloys

SH730 490 (300 - 660) 0.0008 (0.0004 - 0.0012)
Miniature Tool

Si < 12%

Titanium alloys
SH730 200 (100 - 330) 0.0008 (0.0004 - 0.0012)
Ti-6AI-4V, etc.

Superalloys SH730 200 (100 - 330) 0.0008 (0.0004 - 0.0012)

Inconel718, etc.

Face grooving

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
Low carbon steels
1015, 1025, etc.
SH730 300 (130 - 460) 0.0012 (0.0004 - 0.002)

Carbon steels, Alloy steels

1055, 4140, etc.
SH730 300 (130 - 460) 0.0012 (0.0004 - 0.002)

Prehardened steels SH730 300 (130 - 460) 0.0012 (0.0004 - 0.002)

NAK80, PX5, etc.

Stainless steels SH730 300 (130 - 460) 0.0012 (0.0004 - 0.002)

304, 316, etc.

Grey cast irons SH730 200 (100 - 330) 0.0012 (0.0004 - 0.002)
250, 300, etc.

Ductile cast irons SH730 200 (100 - 330) 0.0012 (0.0004 - 0.002)
65-45-12, 80-55-06, etc.

Aluminum alloys, copper alloys

Si < 12%
SH730 490 (300 - 660) 0.0012 (0.0004 - 0.002)

Titanium alloys
SH730 200 (100 - 330) 0.0012 (0.0004 - 0.002)
Ti-6AI-4V, etc.

Superalloys SH730 200 (100 - 330) 0.0012 (0.0004 - 0.002)

Inconel718, etc.

B394 www.tungaloyamerica.com
MEMO

Miniature Tool

Tungaloy B395
 JS XG R /L
Sc re w -o n to o l ho l d er w i t ho ut o f f set f o r f ron t / re v e r s e t u r n i n g & ex te r n a l groov i n g

ar

b
f
L1
L2
40°
C-type

h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
JSXGR/L1010K8-C 0.7 - 2 6.7 10 10 125 29 10 10 JX*R/L8...
JSXGR/L1212K8-C 0.7 - 2 6.7 12 12 125 29 12 12 JX*R/L8...
JSXGR/L1616K8 0.7 - 2 6.5 16 16 125 29 16 16 JX*R/L8...
JSXGR/L2020K8 0.7 - 2 6.5 20 20 125 29 20 20 JX*R/L8...
JSXGR/L2525K8 0.7 - 2 6.5 25 25 125 29 25 25 JX*R/L8...
• Can be wrenched also from the back with a double-head screw.
• This toolholders can be used for JXG insert (grooving), JXF insert (front-turning), JXK insert (reverse-turning).
Miniature Tool

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSXGR/L CSTB-4SD T-8F (T-8L)

INSERT
J XG ( h a n d ed inser t wit h sharp ed g e )
W rε

θ°
25

ød T Right hand (R) shown.

Coated Uncoated Max.

rε ød T W+ 0.05
0
Designation J740 TH10 θ° groove
(mm) (mm) (mm) (mm)
R L R L depth
JXGR/L8070FA 0 䖃 䖃 䖃 䖃 8 3.97 0.7 15 4.5

JXGR/L8070FA-005 0.05 䖃 8 3.97 0.7 15 4.5

JXGR/L8100FA 0 䖃 䖃 䖃 䖃 8 3.97 1 15 6

JXGR/L8100FA-005 0.05 䖃 8 3.97 1 15 6

JXGR/L8100FA45 0 䖃 䖃 8 3.97 1 15 4.5

JXGR/L8100FA45-005 0.05 䖃 8 3.97 1 15 4.5

JXGR/L8150FA 0 䖃 䖃 䖃 䖃 8 3.97 1.5 15 6

JXGR/L8150FA-005 0.05 䖃 8 3.97 1.5 15 6

JXGR/L8150FA50 0 䖃 䖃 8 3.97 1.5 15 5

JXGR/L8150FA50-005 0.05 䖃 8 3.97 1.5 15 5

JXGR/L8180FA 0 䖃 䖃 8 3.97 1.8 15 6

JXGR/L8180FA-005 0.05 䖃 8 3.97 1.8 15 6

JXGR/L8200FA 0 䖃 䖃 䖃 䖃 8 3.97 2 15 6

JXGR/L8200FA-005 0.05 䖃 8 3.97 2 15 6

JXGR/L8200FN 0 䖃 䖃 䖃 䖃 8 3.97 2 0 6

JXGR/L8200FN-005 0.05 䖃 8 3.97 2 0 6

䖃 : Line up
Reference pages
Standard cutting conditions → B398

B396 www.tungaloyamerica.com
J SV G R /L
Ex te r n a l g ro o v i n g to o l ho l d er s

ar

b
f
L1
L2
35° C-type

h1

h
Right hand (R) shown.

Inch W ar h b L1 L2 h1 f Insert
JSVGR/L062.5 0.013 - 0.079 0.244 0.375 0.375 5.000 0.875 0.375 0.375 JVGR/L...
JSVGR/L082.5 0.013 - 0.079 0.244 0.500 0.500 5.000 0.875 0.500 0.500 JVGR/L...
JSVGR/L102.5 0.013 - 0.079 0.244 0.625 0.625 5.000 0.875 0.625 0.625 JVGR/L...

Metric W ar h b L1 L2 h1 f Insert
JSVGR/L1010K-C 0.33 - 2 6.2 10 10 125 23 10 10 JVGR/L...
JSVGR/L1212K-C 0.33 - 2 6.2 12 12 125 23 12 12 JVGR/L...

Miniature Tool
JSVGR/L1616K 0.33 - 2 6.2 16 16 125 23 16 16 JVGR/L...

• Recommend clamping torque: 2.3 N∙m

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSVGR/L CSTB-3S T-9F (T-8L)

INSERT
J V G ( h a n d e d inser t wit h sharp ed g e)
W
G

ød T
Right hand (R) shown.

Coated Cermet Uncoated Max.

ød T W+ 0.05
0 G groove
Designation SH725 J740 NS9530 TH10
(mm) (mm) (mm) (mm) depth
R L R L R L R L (mm)
JVGR/L033F 䖃 䖃 䖃 䖃 7.94 3.18 0.33 0.8 0.7

JVGR/L050F 䖃 䖃 䖃 䖃 7.94 3.18 0.5 1.2 1.1

JVGR/L075F 䖃 䖃 䖃 䖃 7.94 3.18 0.75 2 1.9

JVGR/L095F 䖃 䖃 䖃 䖃 7.94 3.18 0.95 2 1.9

JVGR/L100F 䖃 䖃 䖃 䖃 䖃 䖃 䖃 7.94 3.18 1 6 5.5

JVGR/L125F 䖃 䖃 䖃 䖃 7.94 3.18 1.25 5.5 5

JVGR/L150F 䖃 䖃 䖃 䖃 䖃 䖃 䖃 7.94 3.18 1.5 6 5.5

JVGR/L200F 䖃 䖃 䖃 䖃 䖃 7.94 3.18 2 6 5.5

䖃 : Line up

Reference pages
Standard cutting conditions → B398

Tungaloy B397
 STA N DA RD CUT T ING CONDIT IO N S ( JXG t yp e , JV G t yp e in se r t )

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
SH725 164 - 656 0.0004 - 0.004
General steel
J740 33 - 328 0.0004 - 0.004
1045, etc.
NS9530 164 - 492 0.0004 - 0.004

SH725 164 - 656 0.0004 - 0.004

Free-cutting steel
J740 33 - 328 0.0004 - 0.004

SH725 164 - 656 0.0004 - 0.004

Stainless steel
J740 33 - 328 0.0004 - 0.004
303, etc.
NS9530 164 - 492 0.0004 - 0.004

Aluminum alloys, Brass

TH10 33 - 656 0.0004 - 0.004
5056, 6061, etc.

Difficult-to-machine material, Titanium alloys

TH10 33 - 98 0.0004 - 0.004
Ti-6AI-4V, etc.
Miniature Tool

B398 www.tungaloyamerica.com
J STG R /L
Ex te r n a l g ro o v i n g to o l ho l d er s

L1

b
f
L2

h1

h
h2
Right hand (R) shown.

Inch W h b L1 L2 h1 f h2 Insert
JSTGR/L063 0.013 - 0.118 0.375 0.375 5.000 0.750 0.375 0.375 0.100 JTGR/L3...
JSTGR/L083 0.013 - 0.118 0.500 0.500 5.000 0.750 0.500 0.500 - JTGR/L3...
JSTGR/L103 0.013 - 0.118 0.625 0.625 5.000 0.750 0.625 0.625 - JTGR/L3...

Metric W h b L1 L2 h1 f h2 Insert
JSTGR/L1010X3 0.33 - 3 10 10 120 18.5 10 10 2 JTGR/L3...
JSTGR/L1212F3 0.33 - 3 12 12 85 18.5 12 12 - JTGR/L3...

Miniature Tool
JSTGR/L1212X3 0.33 - 3 12 12 120 18.5 12 12 - JTGR/L3...
JSTGR/L1616X3 0.33 - 3 16 16 120 18.5 16 16 - JTGR/L3...
JSTGL1616K3 0.33 - 3 16 16 125 18.5 16 16 - JTGR/L3...
• Recommend clamping torque: 1.2 N∙m

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSTGR/L... CSTB-4SD T-8F (T-8L)

J S-TG L3
Ex te r n a l g ro o v i n g to o l ho l d er s

L1
L2
f

øDs
h
B

h
Left hand (L) shown.

Metric W øDs f L1 L2 h B Insert

JS19K-TGL3 0.33 - 3 19.05 6 125 20 18 11.5 JTGR3...
JS20K-TGL3 0.33 - 3 20 6 125 20 19 11.5 JTGR3...
JS22K-TGL3 0.33 - 3 22 6 125 20 21 11.5 JTGR3...
JS25K-TGL3 0.33 - 3 25.4 10 125 20 24 12.7 JTGR3...
• Left hand toolholders (TGL3) are used with right hand inserts (JTGR3). • Recommend clamping torque: 3.0 N∙m

SPARE PARTS
Designation Clamping screw Wrench
JS**-TGL3 CSTB-4S T-15F

Reference pages
JSTGR/L, JS-TGL3: Inserts → B400 -, Standard cutting conditions → B401

Tungaloy B399
 INSERT
J TG ( s h a r p ed g e)
W rε
2°

G
ød T
Right hand (R) shown.

Coated Cermet Uncoated Max.

W+ 0.05
0 rε
SH725 J740 NS9530 TH10 ød T G groove
Designation (mm) (mm) (mm) (mm) depth
(mm)
R L R L R L R L (mm)
JTGR/L3033F 0.33 0.03 䖃 䖃 䖃 䖃 䖃 9.525 3.18 0.8 0.7

JTGR/L3033F-005 0.33 0.05 䖃 9.525 3.18 0.8 0.7

JTGR/L3043F 0.43 0.03 䖃 9.525 3.18 1.2 1.1

JTGR/L3050F 0.5 0.03 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 1.2 1.1

JTGR/L3050F-005 0.5 0.05 䖃 䖃 9.525 3.18 1.2 1.1

JTGR/L3065F 0.65 0.03 䖃 䖃 9.525 3.18 2 1.9

Miniature Tool

JTGR/L3065F-010 0.65 0.1 䖃 9.525 3.18 2 1.9

JTGR/L3075F 0.75 0.03 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3075F-010 0.75 0.1 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3080F 0.8 0.03 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3080F-010 0.8 0.1 䖃 9.525 3.18 2 1.9

JTGR/L3085F 0.85 0.03 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3095F 0.95 0.03 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3095F-010 0.95 0.1 䖃 䖃 9.525 3.18 2 1.9

JTGR/L3100F 1 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3100F-010 1 0.1 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3110F 1.1 0.05 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3120F 1.2 0.05 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3120F-010 1.2 0.1 䖃 9.525 3.18 2.2 2.1

JTGR/L3125F 1.25 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3125F-010 1.25 0.1 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3130F 1.3 0.05 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3140F 1.4 0.05 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3140F-010 1.4 0.1 䖃 9.525 3.18 2.2 2.1

JTGR/L3145F 1.45 0.05 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3145F-010 1.45 0.1 䖃 9.525 3.18 2.2 2.1

JTGR/L3150F 1.5 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3150F-010 1.5 0.1 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3175F 1.75 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3175F-010 1.75 0.1 䖃 9.525 3.18 2.2 2.1

JTGR/L3180F 1.8 0.05 䖃 䖃 9.525 3.18 2.2 2.1

JTGR/L3200F 2 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3200F-010 2 0.1 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3225F 2.25 0.05 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3250F 2.5 0.05 䖃 䖃 䖃 䖃 䖃 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3250F-010 2.5 0.1 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3275F 2.75 0.05 䖃 9.525 3.18 2.7 2.6

JTGR/L3300F 3 0.05 䖃 䖃 9.525 3.18 2.7 2.6

JTGR/L3300F-010 3 0.1 䖃 9.525 3.18 2.7 2.6

䖃 : Line up

B400 www.tungaloyamerica.com
J TG ( w i t h h o r n ing )
W rε
2°

G
ød T
Right hand (R) shown.

Coated cermet Max.

rε J9530 ød T W+ 0.05
0 G groove
Designation (mm) (mm) (mm) (mm) (mm) depth
R L (mm)
JTGR/L3100 0.05 䖃 9.525 3.18 1 2.2 2.1

JTGR/L3125 0.05 䖃 9.525 3.18 1.25 2.2 2.1

JTGR/L3150 0.05 䖃 9.525 3.18 1.5 2.2 2.1

JTGR/L3200 0.05 䖃 9.525 3.18 2 2.7 2.6

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS ( JTG t yp e in se r t )

Miniature Tool
Cutting speed Feed
ISO Workpiece material Grade
Vc (sfm) f (ipr)
SH725 164 - 656 0.0004 - 0.004

J740 33 - 328 0.0004 - 0.004

General steel
1045, etc.
NS9530 164 - 492 0.0004 - 0.004

J9530 164 - 492 0.0004 - 0.004

SH725 164 - 656 0.0004 - 0.004

Free-cutting steel
J740 33 - 328 0.0004 - 0.004

SH725 164 - 656 0.0004 - 0.004

J740 33 - 328 0.0004 - 0.004

Stainless steel
303, etc.
NS9530 164 - 492 0.0004 - 0.004

J9530 164 - 492 0.0004 - 0.004

Aluminum alloys, Brass

TH10 33 - 656 0.0004 - 0.004
Si < 12%

Difficult-to-machine material,
Titanium alloys TH10 33 - 656 0.0004 - 0.004
Ti-6AI-4V, etc.

Tungaloy B401
 JC C W S R /L
E x te r n a l g ro o v i n g & p a r t i n g - o f f to o l h o l d e r s

L1

b
f
Max. parting off dia.: øDmax L2

h1

h
Right hand (R) shown.

Inch W øDmax h b L1 L2 h1 f Insert

JCCWSR/L062 0.079 0.790 0.375 0.375 5.000 0.748 0.375 0.1875 JCC*200F...
JCCWSR/L082 0.079 0.790 0.500 0.500 5.000 0.748 0.500 0.250 JCC*200F...
JCCWSR/L102 0.079 0.790 0.625 0.625 5.000 0.748 0.625 0.3125 JCC*200F...

Metric W øDmax h b L1 L2 h1 f Insert

JCCWSR/L1010K2 2 20 10 10 125 19 10 10 JCC*200F...
JCCWSR/L1212K2 2 20 12 12 125 19 12 12 JCC*200F...
Miniature Tool

JCCWSR/L1616K2 2 20 16 16 125 19 16 16 JCC*200F...

JCCWSR/L2020K2 2 20 20 20 125 19 20 20 JCC*200F...
JCCWSR/L2525K2 2 20 25 25 125 19 25 25 JCC*200F...

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JCCWSR/L... CSTB-4S T-15F (T-15L)

INSERT
J C C ( s h a r p ed g e)
Neutral Handed insert
(JCCN200F) (JCCR/L200F)
rε rε
W

L θ° L
T

Right hand (R) shown.

Coated Uncoated
rε T W L
Designation J740 TH10 θ°
(mm) (mm) (mm) (mm)
R N L R N L
JCCN200F 0 䖃 䖃 4.8 2 15 -

JCCN200F-005 0.05 䖃 4.8 2 15 -

JCCR/L200F 0 䖃 䖃 䖃 䖃 4.8 2 15 15

JCCR/L200F-005 0.05 䖃 䖃 4.8 2 15 15

䖃 : Line up

Reference pages
Standard cutting conditions → B403

B402 www.tungaloyamerica.com
J C G W S R /L
E x te r n a l g ro o v i n g & p a r t i n g - o f f to o l h o l d e r s

L1

b
f
Max. parting off dia.: øDmax L2

h1

h
Right hand (R) shown.

Metric W øDmax h b L1 L2 h1 f Insert

JCGWSR/L1010K2 2 20 10 10 125 20 10 10 JCGN200F...
JCGWSR/L1212K2 2 20 12 12 125 20 12 12 JCGN200F...
JCGWSR/L1616K2 2 20 16 16 125 20 16 16 JCGN200F...

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JCGWSR/L... CSTB-4S T-15F (T-15L)

Miniature Tool
INSERT
J C G ( s h a r p e d g e)

rε Neutral
(JCGN200F)
W

L
T

rε Handed insert
(JCGN200FR/L)
W

Right hand (R) shown.

8°

Coated Uncoated
rε T W L
Designation J740 TH10
(mm) (mm) (mm) (mm)
R N L R N L
JCGN200F 0.05 䖃 䖃 3 2 20

JCGN200FR/L 0.05 䖃 䖃 䖃 䖃 3 2 20

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS ( JC C t yp e , JC G t yp e in se r t )

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)
General steel
J740 33- 328 0.0004 - 0.004
1045, etc.

Free-cutting steel J740 33- 328 0.0004 - 0.004

Stainless steel
J740 33- 328 0.0004 - 0.004
303, etc.

Aluminum alloys, Brass

TH10 33 - 656 0.0004 - 0.004
Si < 12%

Difficult-to-machine material,
Titanium alloys TH10 33 - 98 0.0004 - 0.004
Ti-6AI-4V, etc.

Tungaloy B403
 JC G SSR /L
E x te r n a l g ro o v i n g & p a r t i n g - o f f to o l h o l d e r s

b
f
Max. parting off dia.: øDmax L1
L2

h1

h
Right hand (R) shown.

Metric W øDmax h b L1 L2 h1 f Insert

JCGSSR/L1010-20 2 20 10 10 125 15 10 10.2 GE20...
JCGSSR/L1212-20 2 25 12 12 125 19 12 12.2 GE20...
JCGSSR/L1616-20 2 32 16 16 125 22.5 16 16.2 GE20...

SPARE PARTS
Designation Clamping screw Wrench
JCGSSR/L... CSTB-3 T-9F
Miniature Tool

INSERT
GE20
w +0.1
0

rε L
h

rε Coated Cermet W L h
Designation
(mm) GH730 NS9530 (mm) (mm) (mm)
GE20 0.2 䖃 䖃 2 10 3.5
䖃 : Line up
For aluminium
and non-ferrous
metals
w

rε L

rε Uncoated W L h
Designation (mm) (mm) (mm)
(mm) KS05F
GE20-AL 0.2 䖃 2 10 3.5
䖃 : Line up

Reference pages
Standard cutting conditions → B405

B404 www.tungaloyamerica.com
 STA N DA R D CUT T ING CONDIT IONS ( G E t yp e in se r t )

Cutting speed Feed

ISO Workpiece material Grade
Vc (sfm) f (ipr)

Low carbon steels NS9530 326 - 656 0.002 - 0.006

Alloy steels
( ~ 150HB) GH730 164 - 591 0.002 - 0.006

Medium carbon steels NS9530 262 - 591 0.002 - 0.006

Alloy steels
(150 ~ 250HB) GH730 164 - 591 0.002 - 0.006

High carbon steels NS9530 262 - 591 0.002 - 0.006

Alloy steels
(250HB ~ ) GH730 164 - 394 0.002 - 0.006

Stainless steels GH730 164 - 394 0.002 - 0.006

Gray and
GH730 164 - 591 0.002 - 0.006
ductile cast irons

Aluminum alloys KS05F 658 - 984 0.001 - 0.004

Non-ferrous metals

Miniature Tool

Tungaloy B405
 JSTTR /L
E x te r n a l t h re ad i ng to o l ho l d er s

L1

b
f
L2
5˚

h1

h
h2
Right hand (R) shown.

Inch h b L1 L2 h1 f h2 Insert
JSTTR/L063 0.375 0.375 5.000 0.6875 0.375 0.375 0.100 JTTR/L3...
JSTTR/L083 0.500 0.500 5.000 0.6875 0.500 0.500 0.100 JTTR/L3...
JSTTR/L103 0.625 0.625 5.000 0.6875 0.625 0.625 0.100 JTTR/L3...

Metric h b L1 L2 h1 f h2 Insert
JSTTR/L1010X3 10 10 120 18.5 10 9.5 2 JTTR/L3...
JSTTR/L1212F3 12 12 85 18.5 12 11.5 - JTTR/L3...
Miniature Tool

JSTTR/L1212X3 12 12 120 18.5 12 11.5 - JTTR/L3...

JSTTR/L1616X3 16 16 120 18.5 16 15.5 - JTTR/L3...

• Recommend clamping torque: 1.2 N.m

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSTTR/L... CSTB-4SD T-8F (T-8L)

JS-TTL3
E x te r n a l t h re a d i ng to o l ho l d er s

L1
90°
f

øDs
h
B

h
Left hand (L) shown.

Metric øDs f L1 h B Insert

JS19K-TTL3 19.05 10 125 18 11.5 JTTR30...
JS20K-TTL3 20 10 125 19 11.5 JTTR30...
JS22K-TTL3 22 10 125 21 11.5 JTTR30...
JS25K-TTL3 25.4 10 125 24 12.7 JTTR30...
• Recommend clamping torque: 3.5 N.m

SPARE PARTS
Designation Clamping screw Wrench
JS**-TTL3 CSTB-4S T-15F

Reference pages
JSTTR/L, JS-TTL3: Inserts → B407

B406 www.tungaloyamerica.com
 INSERT
J T T ( s h a r p e d g e)
θ°
rε

ød s T Right hand (R) shown.

Coated Cermet Uncoated

rε ød T s
Designation SH725 J740 NS9530 TH10 θ°
(mm) (mm) (mm) (mm)
R L R L R L R L
JTTR/L3005F-55 0.05 䖃 䖃 55 9.525 3.18 0.6

JTTR/L3005F 0.05 䖃 䖃 䖃 䖃 䖃 60 9.525 3.18 0.9

JTTR/L3010F 0.1 䖃 䖃 䖃 䖃 䖃 60 9.525 3.18 0.9

Machinable pitch range: 0.5 to 1 mm 䖃 : Line up

Miniature Tool

Tungaloy B407
 JS X B R /L
E x te r n a l t h re ad i ng to o l ho l d er s

R3

b
L1
L2
40°

h1
C-type

h
Right hand (R) shown.

Metric h b L1 L2 R3 h1 f Insert
JSXBR1010K8-C 10 10 125 29 6.4 10 5.7 JXT*R...
JSXBR1212K8-C 12 12 125 29 6.4 12 7.7 JXT*R...
JSXBR1616K8 16 16 125 29 6.4 16 11.7 JXT*R...
JSXBR2020K8 20 20 125 29 6.4 20 15.7 JXT*R...
JSXBR2525K8 25 25 125 29 6.4 25 20.7 JXT*R...

• Can be wrenched from back side with both end torx screw.
Miniature Tool

• This toolholder is compatible with JXB-type inserts and JXT-type inserts.

SPARE PARTS
Designation Clamping screw Wrench Wrench 1 (Optional parts)
JSXBR... CSTB-4SD T-8F (T-8L)

INSERT
J X T ( s h a r p ed g e)
60° 60°
rε 0.6 rε

ød T T
1-Type 2-Type
JXT1R JXT2R

rε Coated Uncoated ød T
Designation θ° (mm)
(mm) J740 TH10 (mm)
JXT1R6000F 0.03 䖃 䖃 60 8 3.97

JXT2R6000F 0.03 䖃 䖃 60 8 3.97

Machinable pitch range: 0.5 to 1 mm 䖃 : Line up

B408 www.tungaloyamerica.com
B- S/C ER /L
Ex te r n a l t h re a d i n g to o l ho l d er s

b
10° 10°

b
f

f
L2
L1 h1 L1 L2 h1 h1
h1

1°
h
1°
h
B-SER B-CER/L Right hand (R) shown.

Metric h b L1 L2 h1 f Insert
B-SER10H16 20 10 100 15 10 16 16ER/L...
B-SER12K16 24 12 125 18 12 18 16ER/L...
B-CER/L16M16 32 16 150 24 16 22 16ER/L...

SPARE PARTS
Designation Clamp set Shim set Clamping screw Wrench
B-SER**16 - - CSTB-3.5 T-15F

Miniature Tool
B-CER/L16M16 CSP16 A16-1 - T-15F

BC -SER
Ex te r n a l t h re a d i n g to o l ho l d er s

80° L1
h1 20

f1
(30)

95°

b
18
f

17 3 10°
h1
h
Right hand (R) shown.

Metric h b L1 h1 f f1 Insert
BC-SER12K16 24 16 125 12 23 7 16ER/L..., CC*T09T3...

SPARE PARTS
Designation Clamping screw Wrench
BC-SER**16 CSTB-3.5 T-15F

 Tooling examples using BC-type toolholders

Roughing Grooving Threading

Reference pages
B-S/CER/L: Inserts → B418 -, Standard cutting conditions → B416
BC-SER: Inserts → B106 - (CC*T09T3...), B418 - (16ER/L...),
PCD → B179, Standard cutting conditions → B416

Tungaloy B409
Tur nLine - T hre ading
Inch Metric

B 418
Inserts and toolholders
Economical forinserts
double-sided threading
with excellent sharpness

Threading Tool for Oil and Gas B463

Tool series for threading oil well goods

B410 www.tungaloyamerica.com
Tu n gT h r e a d

Tungaloy B411
 A pplicable tool for each ex tern al th r ead typ e

Partial profile Full profile

60° 55° Parallel Taper

Thread type ISO metric Unified Whitworth
pipe thread pipe thread
UNC, UNF BSW, BSF G
- - M R, PT, BSPT
UNEF W BSP, PF
1/8P 1/8P
Thread 60° 55°
60° 60°
55°
55°
form
Tool

1°47
type 1/4P 1/4P

ST type

0.5 ~ 6 mm 0.5 ~ 5 mm
48 ~ 4 TPI 48 ~ 5 TPI 0.5 ~ 6 mm 32 ~ 5 TPI 28 ~ 5 TPI 28 ~ 11 TPI

B432 B418 B419 B420 B422 B424 B425

STCR/L-18
0.8 ~ 3 mm
- - - - -
32 ~ 8 TPI

B457 B459

JS-STCL18
0.8 ~ 3 mm
- - - - -
32 ~ 8 TPI

B458 B459
Threading Tool

T T-R/L
~ 3 mm ~ 3 mm
- - - -
~ 8 TPI ~ 8 TPI

B456 B455 B455

JST TR/L
0.5 ~ 1 mm 0.5 ~ 1 mm
48 ~ 25 TPI 48 ~ 25 TPI - - - -

B460 B461 B461

JS-T TL3
0.5 ~ 1 mm 0.5 ~ 1 mm
48 ~ 25 TPI 48 ~ 25 TPI - - - -

B460 B461 B461

JSXBR/L
0.5 ~ 1 mm
48 ~ 25 TPI - - - - -

B462 B462

1.27 ~ 4.23 mm
20 ~ 6 TPI - - - - -

C021 C026

The page number for the product details is shown in red.

B412 www.tungaloyamerica.com
 Full profile
30° DIN 405 UNJ
Thread type National taper pipe Trapezoidal Round

NPT NPTF TR Rd UNJC,UNJF

1/8P
Thread 60° 60°
30°
30° 60°
form
1°47 1°47
Tool
type

ST type

27 ~ 8 TPI 27 ~ 8 TPI 1.5 ~ 6 mm 8 TPI, 6 TPI 32 ~ 8 TPI

B432 B426 B427 B428 B430 B430

Chaser
11.5 TPI,
8 TPI - - - -

B470 B470

Full profile
API API
Thread type Tubing & Casing Rotary Shoulder Connection
ACME STUB ACME
Round Buttress V-0.038R V-0.040 V-0.050

60° 60° 60°

Thread 60°
29° 29°

form
1°47
30° 30° 30° 30° 30° 30°
Tool

Threading Tool
Taper 10° 3°
type

ST type

10 TPI, 8 TPI 5 TPI (0.75 TPF) - - - 12 ~ 5 TPI -

B432 B429 B429 B428

Lay down (Single side)

5 TPI (0.75 TPF)

- 5 TPI (1 TPF) - - - - -

B463 B464

Lay down (Double side)

4 TPI (2 TPF) 4 TPI (2 TPF)

- - 5 TPI (3 TPF) - -
4 TPI (3 TPF) 4 TPI (3 TPF)

B465 B466 B466 B466

On edge

5 TPI (0.75 TPF)

10 TPI, 8 TPI - - - 16 ~ 3 TPI 16 ~ 3 TPI
5 TPI (1 TPF)

B467 B469 B469 B469 B469

Chaser

10 TPI, 8 TPI 5 TPI (0.75 TPF) - - - - -

B470 B470 B470

The page number for the product details is shown in red.

Tungaloy B413
 A pplic able tool for each in tern al th r ead typ e
Partial profile Full profile

60° 55° ISO metric Unified Whitworth Parallel Taper

Thread type pipe thread pipe thread

- - M UNC, UNF BSW, BSF G, Rp Rc, PT, BSPT

UNEF W BSP, PF, PS
1/8P 1/8P
Thread 60° 55° 55°
60° 60°
form 55°

Tool

1°47
type 1/4P 1/4P

ST type

0.5 ~ 6 mm 0.5 ~ 5 mm
48 ~ 4 TPI 48 ~ 5 TPI 0.5 ~ 6 mm 32 ~ 5 TPI 28 ~ 5 TPI 19 ~ 11 TPI

B434 B418 B419 B420 B422 B424 B425

T T-R

~ 3 mm ~ 3 mm
- - - -
~ 8 TPI ~ 8 TPI

B456 B455 B455

2.11 ~ 5.08 mm
- - - - -
CM
-7
3

12 ~ 5 TPI

C024 C026
Threading Tool

Full profile

National taper pipe 30° DIN 405

Thread type Trapezoidal Round

NPT NPTF TR Rd

Thread 60° 60°

30°
30°
form
1°47 1°47
Tool
type
ST type

27 ~ 8 TPI 14 ~ 8 TPI 1.5 ~ 5 mm 6 TPI

B434 B426 B427 B428 B430

Chaser

11.5 TPI,
8 TPI - - -

B471 B471

The page number for the product details is shown in red.

B414 www.tungaloyamerica.com
 Full profile
API API
Thread type Tubing & Casing Rotary Shoulder Connection
ACME STUB ACME
Round Buttress V-0.038R V-0.040 V-0.050

60° 60° 60°

Thread 60°
29° 29°

form
1°47
30° 30° 30° 30° 30° 30°
Tool Taper 10° 3°
type

ST type

10 TPI, 8 TPI 5 TPI (0.75 TPF) - - - 12 ~ 5 TPI -

B434 B429 B429 B428

Lay down (Single side)

5 TPI (0.75 TPF)

- - - - - -
5 TPI (1 TPF)

B464 B464

Lay down (Double side)

4 TPI (2 TPF) 4 TPI (2 TPF)

- - 5 TPI (3 TPF) - -
4 TPI (3 TPF) 4 TPI (3 TPF)

B466 B466 B466 B466

Threading Tool
On edge

5 TPI (0.75 TPF)

10 TPI, 8 TPI - - - - -
5 TPI (1 TPF)

B468 B469 B469

Chaser

10 TPI, 8 TPI 5 TPI (0.75 TPF) - - - - -

B471 B471 B471

The page number for the product details is shown in red.

Tungaloy B415
 STA N DA RD CUT T ING CONDIT IO N S

Cutting speed: Vc (sfm)

ISO Workpiece material Hardness
AH725 T313V NS9530 TH10

< 200HB 262 - 591 328 - 656 492 - 656 -

Carbon steels
> 200HB 197 - 525 328 - 492 656 - 558 -

Stainless steels - 164 - 427 230 - 427 - -

Cast irons - - 230 - 492 - 70 - 90

Non-ferrous metals - - - - 100 - 500

Heat-resisting alloys - - - - 10 - 40

Hard materials 50 ~ 60HRC - - - 10 - 30

D ESI G NAT ION SYST EM F OR TAC I N S E R TS

1
16 2
I R 175 3 4 5
ISO - B 6

1 Insert size 2 External or Internal 3 Hand of insert 4 Pitch (TPI) 5 Thread type 6 Chipbreaker
Symbol I. C. dia (in) E External R Right hand Partial-profile inserts Partial-profile inserts With
Pitch: 0.5 ~ 1.5 mm
B (Basic selection)
06 - I Internal L Left hand
(0.020"~ 0.063")
60° 60° thread angle
A
Threading Tool

11 0.250 TPI: 48 ~ 16 55° 55° thread angle M With

16 0.375 Pitch: 0.5 ~ 3 mm TR 30° trapezoidal CB With
AG (0.020"~ 0.125")
22 0.500 TPI: 48 ~ 8 ACME 29° trapezoidal - Without
27 0.625 Pitch: 1.75 ~ 3 mm Full-profile inserts - B is the standard chip
G (0.071"~ 0.125") breaker selection with
TPI: 14 ~ 8 ISO Metric more grade options.
Pitch: 3.5 ~ 5 mm UN Unified - M chip breaker option
N (0.142"~ 0.200") for use in gummier
TPI: 7 ~ 5 W Whitworth materials or applications
Pitch: 4 ~ 6 mm where standard breaker
(0.167"~ 0.250")
PT Taper pipe performance is not
Z acceptable. Fewer
Note: Please identify new designation system for internal inserts. TPI: 6 ~ 4 NPT National taper pipe
grade options.
-i.e.“N” “I” Full-profile inserts NPTF National taper pipe
(Example) Conventional: 16NR15ISO pitch (mm)×10 or 100
RAPI
New: 16IR15ISO TPI (Thread Per Inch) API round
(Examples) RD
05: 0.5 mm pitch×10 BAPI API buttress
175: 1.75 mm pitch×100 RD Round (DIN405)
14: 14 TPI
UNJ UNJ

B416 www.tungaloyamerica.com
MEMO

Threading Tool

Tungaloy B417
 INSERT

60° thre ad angle

Applicable toolholders
t t Insert
External Internal
rε rε size
6 SNR/L000*K06SC...
60°

ℓ3
SNR/L000*H06...

0.252"
0.187"
11 SNR/L**11...
16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
0.219" ød B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
Right hand insert Right hand insert 22 CER/L**22... TSNR/L**22
for internal threading shown. for external threading shown.
SNR/L**22...
TCNR/L**22...
CNR/L**22...
27 CER/L**27... CNR/L**27...
Partial-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

TPI
(in) Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 0.020~0.063 48~16 R 6IRA60 䖃 䖃 - 0.035 - 0.0016

11 0.020~0.063 48~16 R 11IRA60 䖃 䖃 䖃 0.250 0.035 0.028 0.0016

11 0.020~0.063 48~16 L 11ILA60 䖃 䖃 䖃 0.250 0.035 0.028 0.0016

16 0.020~0.063 48~16 R 16ERA60 䖃 䖃 䖃 0.375 0.035 0.028 0.0024 16IRA60 䖃 䖃 䖃 0.375 0.035 0.028 0.0016

16 0.020~0.063 48~16 L 16ELA60 䖃 䖃 䖃 0.375 0.035 0.028 0.0024 16ILA60 䖃 䖃 䖃 0.375 0.035 0.028 0.0016

16 0.020~0.125 48~8 R 16ERAG60 䖃 䖃 0.375 0.063 0.047 0.0024 16IRAG60 䖃 䖃 0.375 0.063 0.047 0.0016

16 0.071~0.125 14~8 R 16ERG60 䖃 䖃 䖃 0.375 0.063 0.047 0.0087 16IRG60 䖃 䖃 䖃 0.375 0.063 0.047 0.0047
Threading Tool

16 0.071~0.125 14~8 L 16ELG60 䖃 䖃 0.375 0.020 0.047 0.0087 16ILG60 䖃 䖃 䖃 0.375 0.063 0.047 0.0047

22 0.142~0.200 7~5 R 22ERN60 䖃 䖃 䖃 0.500 0.020 0.047 0.0173 22IRN60 䖃 䖃 䖃 0.500 0.098 0.067 0.0098

22 0.142~0.200 7~5 L 22ELN60 䖃 䖃 0.500 0.020 0.047 0.0173 22ILN60 䖃 䖃 0.500 0.098 0.067 0.0098

27 0.167~0.250 6~4 R 27ERZ60 䖃 䖃 0.625 0.035 0.028 0.0197 27IRZ60 䖃 䖃 0.625 0.125 0.087 0.0110

Partial-profile insert with chipbreaker

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

TPI
(in) Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
11 0.020~0.063 48~16 R 11IRA60-B 䖃 0.250 0.035 0.028 0.0016

11 0.020~0.063 48~16 R 11IRA60-M 䖃 0.250 0.035 0.028 0.0016

16 0.020~0.063 48~16 R 16ERA60-B 䖃* 0.375 0.035 0.031 0.0020 16IRA60-B 䖃* 0.375 0.035 0.031 0.0020

16 0.020~0.063 48~16 R 16ERA60-M 䖃 0.375 0.035 0.028 0.0024 16IRA60-M 䖃 0.375 0.063 0.043 0.0016

16 0.020~0.125 48~8 R 16ERAG60-B 䖃* 0.375 0.067 0.047 0.0024 16IRAG60-B 䖃* 0.375 0.067 0.047 0.0020

16 0.020~0.125 48~8 R 16ERAG60-M 䖃 䖃 0.375 0.063 0.043 0.0024 16IRAG60-M 䖃 䖃 0.375 0.063 0.047 0.0016

16 0.071~0.125 14~8 R 16ERG60-B 䖃* 0.375 0.067 0.047 0.0067 16IRG60-B 䖃* 0.375 0.067 0.047 0.0039

16 0.071~0.125 14~8 R 16ERG60-M 䖃 0.375 0.063 0.047 0.0087 16IRG60-M 䖃 0.375 0.063 0.047 0.0055

22 0.142~0.200 7~5 R 22ERN60-B 䖃 0.500 0.098 0.067 0.0126 22IRN60-B 䖃 0.500 0.098 0.067 0.0075
Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”.
Required to modify the position of the cutting edge.
Colored product needs to change the shim.

Please check the items used and replace shims if necessary AH725
Insert with
(see page B431). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

䖃 : Line up / Packing Quantity = 5 pcs.

B418 www.tungaloyamerica.com
55° thre ad angle
Applicable toolholders
t t Insert
size External Internal
rε rε 6 SNR/L000*K06SC...
55° SNR/L000*H06...

0.252"

ℓ3
0.187"
11 SNR/L**11...
16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
ød B-CER/L**16 TCNR/L**16...
0.219"
BC-SER/L**16 CNR/L**16...
Right hand insert Right hand insert 22 CER/L**22... TSNR/L**22
for internal threading shown. for external threading shown.
SNR/L**22...
TCNR/L**22...
CNR/L**22...

Partial-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

TPI
(in) Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 0.020~0.063 48~16 R 6IRA55 䖃 䖃 - 0.035 - 0.0028

11 0.020~0.063 48~16 R 11IRA55 䖃 䖃 䖃 0.250 0.035 0.028 0.0028

16 0.020~0.063 48~16 R 16ERA55 䖃 䖃 䖃 0.375 0.035 0.028 0.0028 16IRA55 䖃 䖃 䖃 0.375 0.035 0.028 0.0028

16 0.020~0.125 48~8 R 16ERAG55 䖃 0.375 0.067 0.047 0.0028 16IRAG55 䖃 0.375 0.067 0.047 0.0028

16 0.071~0.125 14~8 R 16ERG55 䖃 䖃 䖃 0.375 0.063 0.047 0.0110 16IRG55 䖃 䖃 䖃 0.375 0.067 0.047 0.0098

22 0.142~0.200 7~5 R 22ERN55 䖃 䖃 䖃 0.500 0.098 0.067 0.0197 22IRN55 䖃 䖃 䖃 0.500 0.098 0.067 0.0197

Threading Tool
Partial-profile insert with chipbreaker
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

TPI
(in) Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 AH725
16 0.020~0.063 48~16 R 16ERAG55-B 䖃* 0.375 0.067 0.047 0.0028 16IRAG55-B 䖃* 0.375 0.067 0.047 0.0020

16 0.071~0.125 14~8 R 16ERG55-B 䖃* 0.375 0.067 0.047 0.0091 16IRG55-B 䖃* 0.375 0.067 0.047 0.0079

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”.
Required to modify the position of the cutting edge.
Colored product needs to change the shim.

Please check the items used and replace shims if necessary AH725
Insert with
(see page B431). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B419
 INSERT

ISO metr ic
Applicable toolholders
t t Insert
External Internal

ℓ3
1/8P size
rε rε 6 SNR/L000*K06SC...
60° SNR/L000*H06...

0.252"
0.187"
11 SNR/L**11...
16 CER/L**16... TSNR/L**16
1/4P
B-SER/L**16 SNR/L**16...
0.219" ød B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
Right hand insert Right hand insert 22 CER/L**22... TSNR/L**22
for internal threading shown. for external threading shown.
SNR/L**22...
TCNR/L**22...
CNR/L**22...
27 CER/L**27... CNR/L**27...
Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

(mm) Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 0.75 R 6IR075ISO 䖃 䖃 - 0.020 - 0.0020

6 1 R 6IR10ISO 䖃 䖃 - 0.035 - 0.0028

6 1.25 R 6IR125ISO 䖃 䖃 - 0.035 - 0.0035

6 1.5 R 6IR15ISO 䖃 䖃 - 0.035 - 0.0043

6 1.75 R 6IR175ISO 䖃 䖃 - 0.035 - 0.0047

6 2 R 6IR20ISO 䖃 䖃 - 0.035 - 0.0055

11 0.5 R 11IR05ISO 䖃 䖃 0.250 0.020 0.047 0.0016

Threading Tool

11 0.75 R 11IR075ISO 䖃 0.250 0.020 0.047 0.0020

11 1 R 11IR10ISO 䖃 䖃 䖃 0.250 0.035 0.028 0.0028

11 1 L 11IL10ISO 䖃 0.250 0.035 0.028 0.0028

11 1.25 R 11IR125ISO 䖃 0.250 0.035 0.028 0.0035

11 1.25 L 11IL125ISO 䖃 0.250 0.035 0.028 0.0035

11 1.5 R 11IR15ISO 䖃 䖃 䖃 0.250 0.035 0.028 0.0043

11 1.5 L 11IL15ISO 䖃 0.250 0.035 0.028 0.0043

11 1.75 R 11IR175ISO 䖃 䖃 0.250 0.035 0.028 0.0047

11 1.75 L 11IL175ISO 䖃 0.250 0.035 0.028 0.0047

11 2 R 11IR20ISO 䖃 䖃 0.250 0.035 0.028 0.0055

11 2 L 11IL20ISO 䖃 0.250 0.035 0.028 0.0055

16 0.5 R 16ER05ISO 䖃 䖃 0.375 0.020 0.047 0.0024 16IR05ISO 䖃 0.375 0.020 0.047 0.0016

16 0.75 R 16ER075ISO 䖃 䖃 䖃 0.375 0.020 0.047 0.0035 16IR075ISO 䖃 0.375 0.020 0.047 0.0020

16 1 R 16ER10ISO 䖃 䖃 䖃 0.375 0.035 0.028 0.0051 16IR10ISO 䖃 䖃 䖃 0.375 0.035 0.028 0.0028

16 1 L 16EL10ISO 0.375 0.035 0.028 0.0051 16IL10ISO 䖃 0.375 0.035 0.028 0.0028

16 1.25 R 16ER125ISO 䖃 䖃 0.375 0.035 0.028 0.0063 16IR125ISO 䖃 0.375 0.035 0.028 0.0035

16 1.25 L 16EL125ISO 0.375 0.035 0.028 0.0063 16IL125ISO 䖃 0.375 0.035 0.028 0.0035

16 1.5 R 16ER15ISO 䖃 䖃 䖃 0.375 0.035 0.028 0.0075 16IR15ISO 䖃 䖃 䖃 0.375 0.035 0.028 0.0043

16 1.5 L 16EL15ISO 䖃 䖃 0.375 0.035 0.028 0.0075 16IL15ISO 䖃 0.375 0.035 0.028 0.0043

16 1.75 R 16ER175ISO 䖃 䖃 0.375 0.063 0.047 0.0087 16IR175ISO 䖃 䖃 0.375 0.063 0.047 0.0047

16 2 R 16ER20ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0098 16IR20ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0055

16 2 L 16EL20ISO 䖃 0.375 0.063 0.047 0.0098 16IL20ISO 䖃 9.525 0.063 0.047 0.0055

16 2.5 R 16ER25ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0122 16IR25ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0071

16 3 R 16ER30ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0150 16IR30ISO 䖃 䖃 䖃 0.375 0.063 0.047 0.0083

16 3 L 16EL30ISO 0.375 0.063 0.047 0.0150 16IL30ISO 䖃 0.375 0.063 0.047 0.0083

䖃 : Line up / Packing Quantity = 5 pcs.

B420 www.tungaloyamerica.com
 External insert (in) Internal insert (in)

Hand of cut
Insert size
Pitch Grade Grade
(mm) Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
22 3.5 R 22ER35ISO 䖃 䖃 0.500 0.098 0.067 0.0173 22IR35ISO 䖃 䖃 0.500 0.098 0.067 0.0098

22 4 R 22ER40ISO 䖃 䖃 0.500 0.098 0.067 0.0197 22IR40ISO 䖃 䖃 0.500 0.098 0.067 0.0110

22 4.5 R 22ER45ISO 䖃 0.500 0.098 0.067 0.0220 22IR45ISO 䖃 0.500 0.098 0.067 0.0126

22 5 R 22ER50ISO 䖃 䖃 0.500 0.098 0.067 0.0248 22IR50ISO 䖃 䖃 0.500 0.098 0.067 0.0138

27 6 R 27ER60ISO 䖃 䖃 0.625 0.126 0.087 0.0295 27IR60ISO 䖃 䖃 0.625 0.126 0.087 0.0165

Full-profile insert with chipbreaker

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

(mm) Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
11 0.5 R 11IR05ISO-B 䖃 0.250 0.020 0.047 0.0016

11 0.5 R 11IR05ISO-M 䖃 0.250 0.020 0.047 0.0016

11 0.75 R 11IR075ISO-B 䖃 0.250 0.020 0.047 0.0020

11 0.75 R 11IR075ISO-M 䖃 0.250 0.020 0.047 0.0020

11 1 R 11IR10ISO-B 䖃 0.250 0.035 0.028 0.0031

11 1 R 11IR10ISO-M 䖃 0.250 0.035 0.028 0.0031

11 1.25 R 11IR125ISO-B 䖃 0.250 0.035 0.028 0.0039

11 1.25 R 11IR125ISO-M 䖃 0.250 0.035 0.028 0.0039

11 1.5 R 11IR15ISO-B 䖃 0.250 0.035 0.028 0.0047

11 1.5 R 11IR15ISO-M 䖃 0.250 0.035 0.028 0.0047

11 1.75 R 11IR175ISO-B 䖃 0.250 0.035 0.028 0.0047

11 1.75 R 11IR175ISO-M 䖃 0.250 0.035 0.028 0.0047

Threading Tool
11 2 R 11IR20ISO-B 䖃 0.250 0.035 0.028 0.0055

11 2 R 11IR20ISO-M 䖃 0.250 0.035 0.028 0.0055

16 0.5 R 16ER05ISO-M 䖃 0.375 0.020 0.047 0.0024

16 0.75 R 16ER075ISO-B 䖃* 0.375 0.024 0.024 0.0031

16 0.75 R 16ER075ISO-M 䖃 0.375 0.020 0.047 0.0035

16 1 R 16ER10ISO-B 䖃* 0.375 0.7 0.028 0.0043 16IR10ISO-B 䖃* 0.375 0.028 0.024 0.0020

16 1 R 16ER10ISO-M 䖃 䖃 0.375 0.035 0.028 0.0051 16IR10ISO-M 䖃 0.375 0.035 0.028 0.0031

16 1.25 R 16ER125ISO-B 䖃* 0.375 0.035 0.031 0.0055 16IR125ISO-B 䖃* 0.375 0.035 0.031 0.0028

16 1.25 R 16ER125ISO-M 䖃 0.375 0.035 0.028 0.0063 16IR125ISO-M 䖃 0.375 0.035 0.028 0.0039

16 1.5 R 16ER15ISO-B 䖃* 0.375 0.039 0.031 0.0075 16IR15ISO-B 䖃* 0.375 0.039 0.031 0.0031

16 1.5 R 16ER15ISO-M 䖃 䖃 0.375 0.035 0.028 0.0075 16IR15ISO-M 䖃 䖃 0.375 0.035 0.028 0.0047

16 1.75 R 16ER175ISO-B 䖃* 0.375 0.047 0.035 0.0079 16IR175ISO-B 䖃* 0.375 0.047 0.035 0.0039

16 1.75 R 16ER175ISO-M 䖃 0.375 0.063 0.047 0.0087 16IR175ISO-M 䖃 0.375 0.063 0.047 0.0055

16 2 R 16ER20ISO-B 䖃* 0.375 0.051 0.039 0.0094 16IR20ISO-B 䖃* 0.375 0.051 0.039 0.0043

16 2 R 16ER20ISO-M 䖃 䖃 0.375 0.063 0.047 0.0098 16IR20ISO-M 䖃 0.375 0.063 0.047 0.0055

16 2.5 R 16ER25ISO-B 䖃* 0.375 0.059 0.043 0.0118 16IR25ISO-B 䖃* 0.375 0.059 0.043 0.0055

16 2.5 R 16ER25ISO-M 䖃 0.375 0.063 0.047 0.0122 16IR25ISO-M 䖃 0.375 0.063 0.047 0.0071

16 3 R 16ER30ISO-B 䖃* 0.375 0.063 0.047 0.0150 16IR30ISO-B 䖃* 0.375 0.059 0.043 0.0071

16 3 R 16ER30ISO-M 䖃 0.375 0.063 0.047 0.0150 16IR30ISO-M 䖃 0.375 0.063 0.047 0.0083

22 3.5 R 22ER35ISO-B 䖃 0.500 0.091 0.063 0.0189

22 4 R 22ER40ISO-B 䖃 0.500 0.091 0.063 0.0205

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”. AH725
Required to modify the position of the cutting edge. Insert with
B type chip-breaker
Colored product needs to change the shim.
Conventional shim
Please check the items used and replace
Holder
shims if necessary(see page B431).
Inappropriate Examples
䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B421
 INSERT

Unif ied
Applicable toolholders
1/8P t Insert
size External Internal
rε 11 SNR/L**11...

ℓ3
60° 16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
1/4P 22 CER/L**22... TSNR/L**22
ød
SNR/L**22...
Right hand insert TCNR/L**22...
for external threading shown.
CNR/L**22...

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 T313V AH725 T313V
11 (0.031) 32 R 11IR32UN 䖃 0.250 0.020 0.047 0.0024

11 (0.036) 28 R 11IR28UN 䖃 0.250 0.020 0.047 0.0024

11 (0.042) 24 R 11IR24UN 䖃 0.250 0.035 0.028 0.0028

11 (0.050) 20 R 11IR20UN 䖃 0.250 0.035 0.028 0.0035

11 (0.056) 18 R 11IR18UN 䖃 0.250 0.035 0.028 0.0039

11 (0.063) 16 R 11IR16UN 䖃 0.250 0.035 0.028 0.0043

11 (0.071) 14 R 11IR14UN 䖃 0.250 0.035 0.028 0.0051

Threading Tool

16 (0.031) 32 R 16ER32UN 䖃 0.375 0.020 0.047 0.0039 16IR32UN 䖃 0.375 0.020 0.047 0.0024

16 (0.036) 28 R 16ER28UN 䖃 0.375 0.020 0.047 0.0043 16IR28UN 䖃 0.375 0.020 0.047 0.0024

16 (0.042) 24 R 16ER24UN 䖃 0.375 0.035 0.028 0.0051 16IR24UN 䖃 0.375 0.035 0.028 0.0028

16 (0.050) 20 R 16ER20UN 䖃 0.375 0.035 0.028 0.0063 16IR20UN 䖃 0.375 0.035 0.028 0.0035

16 (0.056) 18 R 16ER18UN 䖃 0.375 0.035 0.028 0.0071 16IR18UN 䖃 0.375 0.035 0.028 0.0039

16 (0.063) 16 R 16ER16UN 䖃 䖃 0.375 0.035 0.028 0.0079 16IR16UN 䖃 䖃 0.375 0.035 0.028 0.0043

16 (0.071) 14 R 16ER14UN 䖃 䖃 0.375 0.063 0.047 0.0091 16IR14UN 䖃 䖃 0.375 0.063 0.047 0.0051

16 (0.077) 13 R 16ER13UN 䖃 0.375 0.063 0.047 0.0094 16IR13UN 䖃 0.375 0.063 0.047 0.0055

16 (0.083) 12 R 16ER12UN 䖃 䖃 0.375 0.063 0.047 0.0106 16IR12UN 䖃 䖃 0.375 0.063 0.047 0.0059

16 (0.091) 11 R 16ER11UN 䖃 0.375 0.063 0.047 0.0114 16IR11UN 䖃 0.375 0.063 0.047 0.0063

16 (0.100) 10 R 16ER10UN 䖃 0.375 0.063 0.047 0.0126 16IR10UN 䖃 0.375 0.063 0.047 0.0071

16 (0.111) 9 R 16ER9UN 䖃 0.375 0.063 0.047 0.0138 16IR9UN 䖃 0.375 0.063 0.047 0.0079

16 (0.125) 8 R 16ER8UN 䖃 䖃 0.375 0.063 0.047 0.0157 16IR8UN 䖃 䖃 0.375 0.063 0.047 0.0087

22 (0.143) 7 R 22ER7UN 䖃 0.500 0.098 0.067 0.0177 22IR7UN 䖃 0.500 0.098 0.067 0.0098

22 (0.167) 6 R 22ER6UN 䖃 0.500 0.098 0.067 0.0209 22IR6UN 䖃 0.500 0.098 0.067 0.0118

22 (0.200) 5 R 22ER5UN 䖃 0.500 0.098 0.067 0.0252 22IR5UN 䖃 0.500 0.098 0.067 0.0142

䖃 : Line up / Packing Quantity = 5 pcs.

B422 www.tungaloyamerica.com
Full-profile insert with chipbreaker
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
16 (0.042) 24 R 16ER24UN-B 䖃* 0.375 0.031 0.028 0.0043

16 (0.042) 24 R 16ER24UN-M 䖃 0.375 0.035 0.028 0.0051

16 (0.050) 20 R 16ER20UN-B 䖃* 0.375 0.035 0.031 0.0055 16IR20UN-B 䖃* 0.375 0.035 0.031 0.0024

16 (0.050) 20 R 16ER20UN-M 䖃 0.375 0.035 0.028 0.0063 16IR20UN-M 䖃 0.375 0.035 0.028 0.0035

16 (0.056) 18 R 16ER18UN-B 䖃* 0.375 0.039 0.031 0.0059 16IR18UN-B 䖃* 0.375 0.039 0.031 0.0031

16 (0.056) 18 R 16ER18UN-M 䖃 0.375 0.035 0.028 0.0071 16IR18UN-M 䖃 0.375 0.035 0.028 0.0039

16 (0.063) 16 R 16ER16UN-B 䖃* 0.375 0.043 0.035 0.19 16IR16UN-B 䖃* 0.375 0.043 0.035 0.0035

16 (0.063) 16 R 16ER16UN-M 䖃 0.375 0.035 0.028 0.0079 16IR16UN-M 䖃 0.375 0.035 0.028 0.0043

16 (0.071) 14 R 16ER14UN-B 䖃* 0.375 0.047 0.039 0.0087 16IR14UN-B 䖃* 0.375 0.047 0.035 0.0043

16 (0.071) 14 R 16ER14UN-M 䖃 0.375 0.063 0.047 0.0091 16IR14UN-M 䖃 0.375 0.063 0.047 0.0043

16 (0.077) 13 R 16ER13UN-B 䖃* 0.375 0.051 0.039 0.0094

16 (0.083) 12 R 16ER12UN-B 䖃* 0.375 0.055 0.043 0.0098 16IR12UN-B 䖃* 0.375 0.055 0.043 0.0047

16 (0.083) 12 R 16ER12UN-M 䖃 0.375 0.063 0.047 0.0106 16IR12UN-M 䖃 0.375 0.063 0.047 0.0059

16 (0.125) 8 R 16ER8UN-B 䖃* 0.375 0.063 0.047 0.0161 16IR8UN-B 䖃* 0.375 0.059 0.043 0.0075

16 (0.125) 8 R 16ER8UN-M 䖃 0.375 0.063 0.047 0.0157 16IR8UN-M 䖃 0.375 0.063 0.047 0.0087

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”.
Required to modify the position of the cutting edge.
Colored product needs to change the shim.

Threading Tool
Please check the items used and replace shims if necessary AH725
Insert with
(see page B431). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B423
 INSERT

W hit wor th
Applicable toolholders
t t Insert
size External Internal
rε rε 6 SNR/L000*K06SC...
55° SNR/L000*H06...

0.252"

ℓ3
0.187"
11 SNR/L**11...
16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
0.219" ød
BC-SER/L**16 CNR/L**16...
Right hand insert Right hand insert 22 CER/L**22... TSNR/L**22
for internal threading shown. for external threading shown.
SNR/L**22...
TCNR/L**22...
CNR/L**22...
Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 (0.053) 19 R 6IR19W 䖃 䖃 - 0.035 - 0.0067
11 (0.053) 19 R 11IR19W 䖃 䖃 䖃 0.250 0.035 0.028 0.0067
11 (0.071) 14 R 11IR14W 䖃 䖃 䖃 0.250 0.035 0.028 0.23
16 (0.036) 28 R 16ER28W 䖃 䖃 0.375 0.035 0.028 0.0043 16IR28W 䖃 0.375 0.035 0.028 0.0043
16 (0.038) 26 R 16ER26W 䖃 0.375 0.035 0.028 0.0047 16IR26W 䖃 0.375 0.035 0.028 0.0047
16 (0.050) 20 R 16ER20W 䖃 0.375 0.035 0.028 0.0063 16IR20W 䖃 0.375 0.035 0.028 0.0063
16 (0.053) 19 R 16ER19W 䖃 䖃 0.375 0.035 0.028 0.0067 16IR19W 䖃 0.375 0.035 0.028 0.0067
16 (0.056) 18 R 16ER18W 䖃 0.375 0.035 0.028 0.0071 16IR18W 䖃 0.375 0.035 0.028 0.0071
Threading Tool

16 (0.063) 16 R 16ER16W 䖃 䖃 0.375 0.035 0.028 0.0079 16IR16W 䖃 䖃 0.375 0.035 0.028 0.0079
16 (0.071) 14 R 16ER14W 䖃 䖃 䖃 0.375 0.063 0.047 0.0091 16IR14W 䖃 䖃 䖃 0.375 0.063 0.047 0.0091
16 (0.071) 14 L 16EL14W 䖃 0.375 0.063 0.047 0.0091
16 (0.083) 12 R 16ER12W 䖃 䖃 0.375 0.063 0.047 0.0106 16IR12W 䖃 䖃 0.375 0.063 0.047 0.0106
16 (0.091) 11 R 16ER11W 䖃 䖃 䖃 0.375 0.063 0.047 0.0114 16IR11W 䖃 䖃 䖃 0.375 0.063 0.047 0.0114
16 (0.100) 10 R 16ER10W 䖃 䖃 0.375 0.063 0.047 0.0126 16IR10W 䖃 䖃 0.375 0.063 0.047 0.0126
16 (0.111) 9 R 16ER9W 䖃 0.375 0.063 0.047 0.0138 16IR9W 䖃 0.375 0.063 0.047 0.0138
16 (0.125) 8 R 16ER8W 䖃 䖃 0.375 0.063 0.047 0.0157 16IR8W 䖃 䖃 0.375 0.063 0.047 0.0157
22 (0.143) 7 R 22ER7W 䖃 0.500 0.098 0.067 0.0177 22IR7W 䖃 0.500 0.098 0.067 0.0177
22 (0.167) 6 R 22ER6W 䖃 0.500 0.098 0.067 0.0209 22IR6W 䖃 0.500 0.098 0.067 0.0209
22 (0.200) 5 R 22ER5W 䖃 0.500 0.098 0.067 0.0252 22IR5W 䖃 0.500 0.098 0.067 0.0252

Full-profile insert with chipbreaker

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
16 (0.053) 19 R 16ER19W-B 䖃* 0.375 0.039 0.031 0.0063
16 (0.053) 19 R 16ER19W-M 䖃 0.375 0.035 0.028 0.0067 16IR19W-M 䖃 0.375 0.035 0.028 0.0067
16 (0.063) 16 R 16ER16W-B 䖃* 0.375 0.043 0.035 0.0079 16IR16W-B 䖃* 0.375 0.043 0.035 0.0071
16 (0.071) 14 R 16ER14W-B 䖃* 0.375 0.047 0.039 0.0094 16IR14W-B 䖃* 0.375 0.047 0.039 0.0083
16 (0.071) 14 R 16ER14W-M 䖃 0.375 0.063 0.047 0.0091 16IR14W-M 䖃 0.375 0.063 0.047 0.0091
16 (0.091) 11 R 16ER11W-B 䖃* 0.375 0.059 0.043 0.0106 16IR11W-B 䖃* 0.375 0.059 0.043 0.0106
16 (0.091) 11 R 16ER11W-M 䖃 0.375 0.063 0.047 0.0114 16IR11W-M 䖃 0.375 0.063 0.047 0.0114

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”. AH725
Required to modify the position of the cutting edge. Insert with
B type chip-breaker
Colored product needs to change the shim.

Please check the items used and replace shims if necessary Conventional shim
Holder
(see page B431).
Inappropriate
Examples

B424 www.tungaloyamerica.com 䖃 : Line up / Packing Quantity = 5 pcs.

Ta per pipe
Applicable toolholders
t t Insert
rε size External Internal
rε 6 SNR/L000*K06SC...

ℓ3
0.252"
55° SNR/L000*H06...

0.187"
11 SNR/L**11...
16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
0.219" ød B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
Right hand insert Right hand insert
for internal threading shown. for external threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 (0.053) 19 R 6IR19PT 䖃 䖃 - 0.035 - 0.0055

11 (0.053) 19 R 11IR19PT 䖃 䖃 䖃 0.250 0.035 0.028 0.0055

11 (0.071) 14 R 11IR14PT 䖃 䖃 䖃 0.250 0.035 0.028 0.0063

16 (0.036) 28 R 16ER28PT 䖃 䖃 0.375 0.035 0.028 0.0035

16 (0.053) 19 R 16ER19PT 䖃 䖃 0.375 0.035 0.028 0.0055 16IR19PT 䖃 0.375 0.035 0.028 0.0055

16 (0.071) 14 R 16ER14PT 䖃 䖃 0.375 0.063 0.047 0.0063 16IR14PT 䖃 䖃 䖃 0.375 0.063 0.047 0.0063

16 (0.091) 11 R 16ER11PT 䖃 䖃 0.375 0.063 0.047 0.0102 16IR11PT 䖃 䖃 䖃 0.375 0.063 0.047 0.0102

Threading Tool
Full-profile insert with chipbreaker
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
16 (0.053) 19 R 16ER19PT-M 䖃 0.375 0.035 0.028 0.0071 16IR19PT-M 䖃 0.375 0.035 0.028 0.0071

16 (0.071) 14 R 16ER14PT-B 䖃* 0.375 0.047 0.039 0.0083 16IR14PT-B 䖃* 0.375 0.039 0.047 0.0083

16 (0.071) 14 R 16ER14PT-M 䖃 0.375 0.063 0.047 0.0098 16IR14PT-M 䖃 0.375 0.063 0.047 0.0098

16 (0.091) 11 R 16ER11PT-B 䖃* 0.375 0.059 0.043 0.0110 16IR11PT-B 䖃* 0.375 0.059 0.043 0.0110

16 (0.091) 11 R 16ER11PT-M 䖃 0.375 0.063 0.047 0.0126 16IR11PT-M 䖃 0.375 0.063 0.047 0.0126

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”.
Required to modify the position of the cutting edge.
Colored product needs to change the shim.

Please check the items used and replace shims if necessary AH725
Insert with
(see page B431). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B425
 INSERT

NPT
Applicable toolholders
t Insert
rε t size External Internal
rε 6 SNR/L000*K06SC...
60°
SNR/L000*H06...

0.252"

ℓ3
0.187"
16 CER/L**16... TSNR/L**16
B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
0.219" ød
Right hand insert Right hand insert
for internal threading shown. for external threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Un-
coated ød t R3 rε Designation Coated Un-
coated ød t R3 rε
AH725 T313V TH10 AH725 T313V TH10
6 (0.056) 18 R 6IR18NPT 䖃 䖃 - 0.035 - 0.0012

16 (0.037) 27 R 16ER27NPT 䖃 0.375 0.020 0.047 0.0008 16IR27NPT 䖃 0.375 0.020 0.047 0.0008

16 (0.056) 18 R 16ER18NPT 䖃 䖃 0.375 0.035 0.028 0.0012 16IR18NPT 䖃 0.375 0.035 0.028 0.0012

16 (0.071) 14 R 16ER14NPT 䖃 0.375 0.063 0.047 0.0016 16IR14NPT 䖃 䖃 0.375 0.063 0.047 0.0016

16 (0.087) 11.5 R 16ER115NPT 䖃 0.375 0.063 0.047 0.0020 16IR115NPT 䖃 䖃 0.375 0.063 0.047 0.0020

16 (0.125) 8 R 16ER8NPT 䖃 0.375 0.063 0.047 0.0028 16IR8NPT 䖃 䖃 0.375 0.063 0.047 0.0028
Threading Tool

Full-profile insert with chipbreaker

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated Cermet ød t R3 rε Designation Coated Cermet ød t R3 rε
AH725 NS9530 AH725 NS9530
16 (0.056) 18 R 16ER18NPT-B 䖃* 0.375 0.039 0.031 0.0020

16 (0.056) 18 R 16ER18NPT-M 䖃 0.375 0.035 0.028 0.0028 16IR18NPT-M 䖃 0.375 0.035 0.028 0.0028

16 (0.071) 14 R 16ER14NPT-B 䖃* 0.375 0.047 0.035 0.0020 16IR14NPT-B 䖃* 0.375 0.047 0.9 0.0020

16 (0.071) 14 R 16ER14NPT-M 䖃 0.375 0.063 0.047 0.0031 16IR14NPT-M 䖃 0.375 0.063 0.047 0.0031

16 (0.087) 11.5 R 16ER115NPT-B 䖃* 0.375 0.059 0.043 0.0035 16IR115NPT-B 䖃* 0.375 0.059 0.043 0.0035

16 (0.087) 11.5 R 16ER115NPT-M 䖃 0.375 0.063 0.047 0.0035 16IR115NPT-M 䖃 0.375 0.063 0.047 0.0035

16 (0.125) 8 R 16ER8NPT-B 䖃* 0.375 0.071 0.051 0.0047 16IR8NPT-B 䖃* 0.375 0.071 0.051 0.0047

Note: 䖃* Please be aware of the different dimensions regarding “t” & “r3”.
Required to modify the position of the cutting edge.
Colored product needs to change the shim.

Please check the items used and replace shims if necessary AH725
Insert with
(see page B431). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

䖃 : Line up / Packing Quantity = 5 pcs.

B426 www.tungaloyamerica.com
NPTF
Applicable toolholders
Insert
t size External Internal
16 CER/L**16... TSNR/L**16
60° B-SER/L**16 SNR/L**16...
B-CER/L**16

ℓ3
TCNR/L**16...
BC-SER/L**16 CNR/L**16...

ød
Right hand insert
for external threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 AH725
16 (0.037) 27 R 16ER27NPTF 䖃 0.375 0.020 0.047 -

16 (0.056) 18 R 16ER18NPTF 䖃 0.375 0.035 0.028 -

16 (0.071) 14 R 16ER14NPTF 䖃 0.375 0.063 0.047 - 16IR14NPTF 䖃 0.375 0.063 0.047 -

16 (0.087) 11.5 R 16ER115NPTF 䖃 0.375 0.063 0.047 - 16IR115NPTF 䖃 0.375 0.063 0.047 -

16 (0.125) 8 R 16ER8NPTF 䖃 0.375 0.063 0.047 - 16IR8NPTF 䖃 0.375 0.063 0.047 -

Threading Tool

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B427
 INSERT

30° Trapezoidal (DIN103)

Applicable toolholders
Insert
t size External Internal
30° 16 CER/L**16... TSNR/L**16

ℓ3
B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
22 CER/L**22... TSNR/L**22
SNR/L**22...
ød TCNR/L**22...
Right hand insert CNR/L**22...
for external threading shown.
27 CER/L**27...

Special full-profile insert (see page B439)

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch Grade Grade

(mm) Designation Coated ød t R3 Designation Coated ød t R3
AH725 T313V AH725 T313V
16 1.5 R 16ER15TR 䖃 0.375 0.035 0.028 16IR15TR 䖃 0.375 0.035 0.028

16 2 R 16ER20TR 䖃 䖃 0.375 0.063 0.051 16IR20TR 䖃 䖃 0.375 0.063 0.051

16 3 R 16ER30TR 䖃 䖃 0.375 0.063 0.051 16IR30TR 䖃 䖃 0.375 0.063 0.051

22 4 R 22ER40TR 䖃 䖃 0.500 0.098 0.079 22IR40TR 䖃 䖃 0.500 0.098 0.079

22 5 R 22ER50TR 䖃 䖃 0.500 0.098 0.079 22IR50TR 䖃 䖃 0.500 0.098 0.079

27 6 R 27ER60TR 䖃 䖃 0.625 0.126 0.098

Threading Tool

29° Trapezoidal (ACME )

Applicable toolholders
t Insert
size External Internal
29° 16 CER/L**16... TSNR/L**16
ℓ3

B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...
22 CER/L**22... TSNR/L**22
SNR/L**22...
ød TCNR/L**22...
Right hand insert CNR/L**22...
for external threading shown.

Special full-profile insert (see page B439)

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 Designation Coated ød t R3
AH725 T313V AH725 T313V
16 (0.083) 12 R 16ER12ACME 䖃 0.375 0.063 0.051 16IR12ACME 䖃 0.375 0.063 0.051

16 (0.100) 10 R 16ER10ACME 䖃 0.375 0.063 0.051 16IR10ACME 䖃 0.375 0.063 0.051

16 (0.125) 8 R 16ER8ACME 䖃 䖃 0.375 0.063 0.051 16IR8ACME 䖃 䖃 0.375 0.063 0.051

16 (0.125) 8 R 16ER8TPI29(STACME) 䖃 0.375 0.063 0.051 16IR8TPI29(STACME) 䖃 0.375 0.063 0.051

22 (0.167) 6 R 22ER6ACME 䖃 䖃 0.500 0.098 0.079 22IR6ACME 䖃 䖃 0.500 0.098 0.079

22 (0.166) 6 R 22ER6TPI29(STACME) AH725 䖃 0.500 0.080 0.078 22IR6TPI29(STACME) AH725 䖃 0.500 0.080 0.078

22 (0.200) 5 R 22ER5ACME 䖃 䖃 0.500 0.098 0.079 22IR5ACME 䖃 䖃 0.500 0.098 0.079

22 (0.200) 5 R 22ER5TPI29(STACME) AH725 䖃 0.500 0.098 0.078 22IR5TPI29(STACME) AH725 䖃 0.500 0.098 0.078
Note: TPI29 inserts are semi-topping, STACME inserts are full-topping.

䖃 : Line up / Packing Quantity = 5 pcs.

B428 www.tungaloyamerica.com
API Round
Applicable toolholders
t Insert
size External Internal

ℓ3
rε 16 CER/L**16... TSNR/L**16
60° B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...

ød
Right hand insert
for internal threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference

(in)
Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 T313V AH725 T313V
16 (0.100) 10 R 16ER10RAPI 䖃 0.375 0.063 0.047 0.0142 16IR10RAPI 䖃 䖃 0.375 0.063 0.047 0.0142

16 (0.125) 8 R 16ER8RAPI 䖃 0.375 0.063 0.047 0.0169 16IR8RAPI 䖃 䖃 0.375 0.063 0.047 0.0169

Full-profile insert with chipbreaker

External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 AH725

Threading Tool
16 (0.100) 10 R 16ER10RD-CB 䖃 0.375 0.047 0.059 0.0142 16IR10RD-CB 䖃 0.375 0.047 0.059 0.0142

16 (0.125) 8 R 16ER8RD-CB 䖃 0.375 0.051 0.059 0.0169 16IR8RD-CB 䖃 0.375 0.051 0.059 0.0169

API But tre ss

Applicable toolholders
t Insert
size External Internal
22 CER/L**22... TSNR/L**22
SNR/L**22...
ℓ3

TCNR/L**22...
CNR/L**22...
10°
3°
ød
Right hand insert
for external threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 Designation Coated ød t R3
AH725 AH725
22 (0.200) 5 R 22ER5BAPI 䖃 0.500 0.146 0.087 22IR5BAPI 䖃 0.500 0.136 0.087

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B429
 INSERT

Round (DIN405)
Applicable toolholders
t Insert
size External Internal
rε 16 CER/L**16... TSNR/L**16
30°

ℓ3
B-SER/L**16 SNR/L**16...
B-CER/L**16 TCNR/L**16...
BC-SER/L**16 CNR/L**16...

ød
Right hand insert 60°
for external threading shown.

Full-profile insert
External insert (in) Internal insert (in)
Hand of cut
Insert size

Pitch
Grade Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 rε Designation Coated ød t R3 rε
AH725 AH725
16 (0.125) 8 R 16ER8RD-B 䖃 0.375 0.051 0.055 -

16 (0.125) 6 R 16ER6RD-B 䖃 0.375 0.067 0.059 - 16IR6RD-B 䖃 0.375 0.059 0.055 -

UNJ (Ae rospace)

Applicable toolholders
t
Threading Tool

Insert
size External
1/8P rε 16 CER/L**16...
ℓ3

60° B-SER/L**16
B-CER/L**16
BC-SER/L**16

ød
60°
Right hand (R) shown.

Full-profile insert
External insert (in)
Hand of cut
Insert size

Pitch
Grade
TPI

(Reference)

(in)
Designation Coated ød t R3 rε
AH725
16 (0.031) 32 R 16ER32UNJ 䖃 0.375 0.020 0.047 0.0051

16 (0.036) 28 R 16ER28UNJ 䖃 0.375 0.020 0.047 0.0059

16 (0.042) 24 R 16ER24UNJ 䖃 0.375 0.035 0.028 0.0071

16 (0.050) 20 R 16ER20UNJ 䖃 0.375 0.035 0.028 0.0083

16 (0.056) 18 R 16ER18UNJ 䖃 0.375 0.035 0.028 0.0094

16 (0.063) 16 R 16ER16UNJ 䖃 0.375 0.035 0.028 0.0102

16 (0.071) 14 R 16ER14UNJ 䖃 0.375 0.063 0.047 0.0118

16 (0.083) 12 R 16ER12UNJ 䖃 0.375 0.063 0.047 0.0138

16 (0.100) 10 R 16ER10UNJ 䖃 0.375 0.063 0.047 0.0165

16 (0.125) 8 R 16ER8UNJ 䖃 0.375 0.063 0.047 0.0209

䖃 : Line up / Packing Quantity = 5 pcs.

B430 www.tungaloyamerica.com
 I M P O R TA N T NOT ICE - Rep l aceme n t o f sh im sh e e t

Please check the items used and replace shims if necessary AH725
Insert with
(see the following list). B type chip-breaker

Conventional shim
Holder

Inappropriate
Examples

List of interchangeable Shims (Size 16 · Insert).

External designation Internal designation
Holder type Lead Angle
1 Conventional 1 Standard (New) 2 Conventional 2 Standard (New)
4° GXE16-4DT AE16-4DT GXN16-4DT AN16-4DT
3° GXE16-3DT AE16-3DT GXN16-3DT AN16-3DT
Dual clamping 2° GXE16-2DT AE16-2DT GXN16-2DT AN16-2DT
methods of
1° (Standard) GX16-1DT A16-1DT GX16-1DT A16-1DT
screw-on and
clamp-on 0° GXE16-0DT AE16-0DT GXN16-0DT AN16-0DT
-1° GXE16-99DT AE16-99DT GXN16-99DT AN16-99DT
-2° GXE16-98DT AE16-98DT GXN16-98DT AN16-98DT
4° GXE16-4 AE16-4 GXN16-4 AN16-4
3° GXE16-3 AE16-3 GXN16-3 AN16-3
2° GXE16-2 AE16-2 GXN16-2 AN16-2
Clamp-on 1° (Standard) GXE16-1 A16-1 GXN16-1 A16-1
0° GXE16-0 AE16-0 GXN16-0 AN16-0
-1° GXE16-99 AE16-99 GXN16-99 AN16-99
-2° GXE16-98 AE16-98 GXN16-98 AN16-98

Threading Tool
Target items for the replacement of shims (Size 16 · Insert).
External Internal
Thread type
Designation Grade Replacement Designation Grade Replacement
16IR15ISO-B AH725
ISO 16IR175ISO-B AH725
16IR20ISO-B AH725
16ERAG55-B AH725 16IRAG55-B AH725
55°
16IRG55-B AH725
16ERA60-B AH725 16IRAG60-B AH725
60° 1 Conventional 16IRA60-B AH725 2 Conventional
16IRG60-B AH725
16IR18UN-B AH725
UN 16IR16UN-B AH725
1 Standard (New) 16IR14UN-B AH725 2 Standard (New)
16IR16W-B AH725
W
16IR14W-B AH725
PT 16IR14PT-B AH725
16ER8NPT-B AH725 16IR14NPT-B AH725
NPT
16IR115NPT-B AH725

Tungaloy B431
 C E R /L
E x te r n a l t h re a d i ng to o l ho l d er s, A l ter nat i v e c l a m p i n g of s c re w - on or c l a m p - on (DT t y p e on l y )

L1
L2

b
f
10°

h1

h
Right hand (R) shown.

Inch h b L1 L2 h1 f Insert
CER/L 123-DT 0.75 0.75 5 0.87 0.75 1 16ER/L...
CER/L 163-DT 1 1 6 1 1 1.25 16ER/L...
CER 203-DT 1.25 1.25 6 1.25 1.25 1.5 16ER/L...
CER164-DT 1 1 6 1 1 1.25 22ER/L...
CER 204-DT 1.25 1.25 6 1.25 1.25 1.50 22ER/L...

Metric h b L1 L2 h1 f Insert
CER/L1212H16DT 12 12 100 24 12 16 16ER/L...
CER/L1616H16DT 16 16 100 24 16 20 16ER/L...
CER/L2020K16DT 20 20 125 24 20 25 16ER/L...
CER/L2525M16DT 25 25 150 28 25 32 16ER/L...
CER/L2525M22DT 25 25 150 31.3 25 32 22ER/L...
CER3232P16T 32 32 170 32 32 40 16ER...
CER3232P22T 32 32 170 32 32 40 22ER...
CER2525M27T 25 25 150 34 25 32 27ER...
CER3232P27T 32 32 170 34 32 40 27ER...
Threading Tool

Note: A clamp set for CER/L type consists of a clamp and a clamping screw. A shim set for CER/L type consists of a shim and a shim screw. Standard shims for CER/L type
can be used for both left hand and right hand toolholders. Use either of the sides depending on the hand.

SPARE PARTS
Designation Clamp set Clamping screw Screw Shim Shim set Wrench Wrench 1 Wrench 2
CER/L 123-DT CSP16 CSTB-3.5ST DTS5 - 3.5 A16 - 1DT - P-3.5 T-15F -
CER/L 163-DT CSP16 CSTB-3.5ST DTS5 - 3.5 A16 - 1DT - P-3.5 T-15F -
CER 203-DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - P-3.5 T-15F -
CER164-DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - P-4 T-20F -
CER 204-DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - P-4 T-20F -
CER/L**16DT CSP22 CSTB-3.5ST DTS5-3.5 A16-1DT - P-3.5 T-15F -
CER/L2525M22DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - P-4 T-15F T-20F
CER3232P16T CSP16 - - - A16-1 - T-15F -
CER3232P22T CSP22 - - - NXE22-1 - T-20F -
CER**27T CSP27 - - - NXE27-1 P-4 - -

Reference pages
CER/L: Inserts → B418 -, Standard cutting conditions → B416

B432 www.tungaloyamerica.com
B- S/C ER /L
Ex te r n a l t h re a d i n g to o l ho l d er s f o r sm al l l at he

b
10°

b
f

f
L2 10°
L1 h1 L1 L2 h1
h1

1°
h
h
B-SER B-CER/L Right hand (R) shown.

Metric h b L1 L2 h1 f Insert
B-SER10H16 20 10 100 15 10 16 16ER...
B-SER12K16 24 12 125 18 12 18 16ER...
B-CER/L16M16 32 16 150 24 16 22 16ER/L...

SPARE PARTS
Designation Clamp set Shim set Clamping screw Wrench
B-SER**16 - - CSTB-3.5 T-15F
B-CER/L16M16 CSP16 A16-1 - T-15F

BC -SER
Mu l t i f u n c t i o n a l exter nal t hread i ng to o l ho l d er s f or s m a l l l a t h e

Threading Tool
80° L1
h1 20 f1
(30)

95°

b
18
f

17 3 10°
h1
h
Right hand (R) shown.

Metric h b L1 h1 f f1 Insert
BC-SER12K16 24 16 125 12 23 7 16ER..., CC*T09T3...

SPARE PARTS
Designation Clamping screw Wrench
BC-SER12K16 CSTB-3.5 T-15F

Reference pages
B-S/CER/L: Inserts → B418 -, Standard cutting conditions → B416
BC-SER: Inserts → B106 - (CC*T09T3...), B418 - (16ER...),
Standard cutting conditions → B416

Tungaloy B433
 SN R /L-2/3
Sm a l l b a r s f o r i nter nal t hread i ng , S crew - on c l a m p

øDs
øDm

f
L2
L1 h

Le°
18°
Right hand (R) ,carbide shank type shown.

Metric Material øDm øDs f L1 L2 h Le° Insert

SNR0006H06-2 STEEL 8 8 4.7 100 18 7 2 6IR...
SNR0006H06-3 STEEL 8 8 4.7 100 18 7 3 6IR...
SNR0008H06-2 STEEL 10 8 5.7 100 18 7 2 6IR...
SNR0008H06-3 STEEL 10 8 5.7 100 18 7 3 6IR...
SNR0006K06SC-2 CARBIDE 8 8 4.7 125 30 7 2 6IR...
SNR0006K06SC-3 CARBIDE 8 8 4.7 125 30 7 3 6IR...
SNR0008K06SC-2 CARBIDE 10 8 5.7 125 18 7 2 6IR...
SNR0008K06SC-3 CARBIDE 10 8 5.7 125 18 7 3 6IR...
Note: When using the right hand insert (6IR** type), is used for the right hand toolholders (SNR** type).

SPARE PARTS
Designation Clamping screw Wrench
SNR0006H06... CSTB-2L040 T-6F
SNR0008H06... CSTB-2L T-6F
SNR0006K06SC... CSTB-2L040 T-6F
SNR0008K06SC... CSTB-2L T-6F
Threading Tool

Reference pages
SNR/L-2/3: Inserts → B418 -, Standard cutting conditions → B416

B434 www.tungaloyamerica.com
S N R /L
I nte r n a l t h re a d i n g b ar s, S crew - o n cl am p

L1 øDs
15° R3 h
øDm L2

b
Carbide reinforced

Le°
(Only for Tsuppari-Ichiban) Right hand (R),
Tsuppari-Ichiban shank type shown.

Metric Material øDm øDs f L1 L2 ℓ3 h b Le° Insert

TSNR0016Q16 TSUPPARI 19 16 10.6 180 40 59 15 - 1 16IR...
TSNR0020R22 TSUPPARI 24 20 13.9 200 50 49 18 - 1 22IR...
SNR/L0010K11 STEEL 12 16 6.6 125 25 - 15 15.5 1 11IR/L...
SNR0010K11-2 STEEL 12 16 6.6 125 25 - 15 15.5 2 11IR...
SNR0010K11-3 STEEL 12 16 6.6 125 25 - 15 15.5 3 11IR...
SNR/L0013L11 STEEL 15 16 8.2 140 32.5 - 15 15.5 1 11IR/L...
SNR0013L11-2 STEEL 15 16 8.2 140 32.5 - 15 15.5 2 11IR...
SNR0013L11-3 STEEL 15 16 8.2 140 32.5 - 15 15.5 3 11IR...
SNR/L0016M16 STEEL 19 16 10.6 150 40 - 15 15.5 1 16IR/L...
SNR0016M16-2 STEEL 19 16 10.6 150 40 - 15 15.5 2 16IR...
SNR0016M16-3 STEEL 19 16 10.6 150 40 - 15 15.5 3 16IR...
SNR/L0020Q22 STEEL 24 20 13.9 180 50 - 18 19 1 22IR/L...
SNR0020Q22-2 STEEL 24 20 13.9 180 50 - 18 19 2 22IR...
SNR0020Q22-3 STEEL 24 20 13.9 180 50 - 18 19 3 22IR...
SNR0010M11SC CARBIDE 13 10 7.4 150 24 - 9 - 1 11IR...
SNR0010M11SC-2 CARBIDE 13 10 7.4 150 24 - 9 - 2 11IR...
SNR0010M11SC-3 CARBIDE 13 10 7.4 150 24 - 9 - 3 11IR...

Threading Tool
SNR0012P11SC CARBIDE 15 12 8.5 170 28 - 11 - 1 11IR...
SNR0012P11SC-2 CARBIDE 15 12 8.5 170 28 - 11 - 2 11IR...
SNR0012P11SC-3 CARBIDE 15 12 8.5 170 28 - 11 - 3 11IR...
SNR/L0016R16SC CARBIDE 20 16 11.9 200 35 - 15 - 1 16IR/L...
SNR0016R16SC-2 CARBIDE 20 16 11.9 200 35 - 15 - 2 16IR...
Note: When using a right or left hand insert, the right hand insert (**IR...type) is used for the right hand toolholders (SNR...type) and left hand insert (**IL...type) is used for the left
hand toolholders (SNL...type).

SPARE PARTS
Designation Clamping screw Wrench
TSNR0016Q16 CSTB-3.5 T-15F
TSNR0020R22 CSTB-4 T-15F
SNR/L00**11... CSTB-2.5 T-8F
SNR/L0016M16... CSTB-3.5 T-15F
SNR/L0020Q22... CSTB-4 T-15F
SNR00**11SC... CSTB-2.5 T-8F
SNR/L0016R16SC... CSTB-3.5 T-15F

Reference pages
SNR/L: Inserts → B418 -, Standard cutting conditions → B416

Tungaloy B435
 SI R /L
I n te r n a l t h re a di ng b ar s, S crew - o n cl am p

15° øD2
øDm

øDs
L2
L1 Coolant hole

Right hand (R) shown.

Inch Material øDm øDs øD2 f L1 L2 Coolant Insert

SIR 0625 P16B STEEL 0.750 0.750 0.625 0.450 7.000 1.570 Y 16IR...
SIR 0750 P16B STEEL 0.900 0.750 0.750 0.900 7.000 - Y 16IR...
SIR 1000 R16B STEEL 1.160 1.000 1.000 0.650 8.000 - Y 16IR...
SIR 1250 S16 STEEL 1.420 1.250 1.250 0.770 10.000 - N 16IR...

SPARE PARTS
Designation Clamping screw Shim Shim screw Wrench Seal cap
SIR 0625 P16B SR 5-40-L9.7-S16S - - T-10/5 PL 075
SIR 0750 P16B SR 5-40-L12.2-S16 AI16 SR 5-40-L6.8-A16 T-10/5 PL 075
SIR 1000 R16B SR 5-40-L12.2-S16 AI16 SR 5-40-L6.8-A16 T-10/5 PL 100
SIR 1250 S16 SR 5-40-L12.2-S16 AI16 SR 5-40-L6.8-A16, SR 8-32-L5.8-A22 T-10/5 -
Threading Tool

Reference pages
SIR/L: Inserts → B418 -, Standard cutting conditions → B416

B436 www.tungaloyamerica.com
CN R /L
I nte r n a l t h re a d i n g b ar s, A l ter nat i v e cl am p i ng of s c re w - on or c l a m p - on (DT t y p e on l y )

L1 øDs
øDm θ° R3 h
L2

b
Carbide reinforced

Le°
(Only for Tsuppari-Ichiban)
Right hand (R),
Tsuppari-Ichiban shank type shown.

Metric Material øDm øDs f L1 L2 ℓ3 h b θ° Le° Insert

TCNR0020R16DT TSUPPARI 24 20 14 200 30 49 18 - 15 1 16IR...
TCNR0025S16DT TSUPPARI 29 25 16.5 250 38 64 23 - 15 1 16IR...
TCNR0025S22DT TSUPPARI 30 25 18.2 250 38 64 23 - 15 1 22IR...
CNR/L0020P16 STEEL 24 20 14 170 30 - 18 19 15 1 16IR/L...
CNR/L0025R16 STEEL 29 25 16.5 200 38 - 23 24 15 1 16IR/L...
CNR/L0032S16 STEEL 37 32 20.1 250 48 - 30 31 15 1 16IR/L...
CNR/L0025R22 STEEL 30 25 18.2 200 38 - 23 24 15 1 22IR/L...
CNR/L0032S22 STEEL 38 32 21.9 250 48 - 30 31 15 1 22IR/L...
CNR0040T27 STEEL 46 40 26.9 300 60 - 37 38.5 10 1 27IR...

Note: A clamp set for CNR/L type toolholders consists of a clamp and a clamping screw. A shim set for CNR/L type toolholders consists of a shim and a shim fixing screw.
Standard shims for CNR/L type toolholders are commonly used for right and left hand toolholders. The right hand insert (IR) is used for the right hand toolholder (CNR...) and left
hand insert (IL) is used for left hand toolholder (CNL...).

SPARE PARTS
Designation Clamp set Clamping screw Screw Shim Shim set R Shim set L Wrench Wrench 1 Wrench 2
TCNR002**16DT CSP16 CSTB-3.5ST DTS5-3.5 A16-1DT - - P-3.5 T-15F -
TCNR0025S22DT CSP22 CSTB-4ST DTS6-4 GX22-1DT - - P-4 T-15F T-20F

Threading Tool
CNR/L**16 CSP16 - - - A16-1 A16-1 - T-15F -
CNR/L**22 CSP22 - - - NXN22-1 NXE22-1 - T-20F -
CNR0040T27 CSP27 - - - NXN27-1 NXE27-1 P-4 - -

Reference pages
CNR/L: Inserts → B418 -, Standard cutting conditions → B416

Tungaloy B437
 Thread ing M et ho d s and Co mb i n a t io n s

External threading Internal threading

Right hand thread Left hand thread Right hand thread Left hand thread

Work rotation Regular Work rotation Reverse Work rotation Regular Work rotation Reverse
Feed direction Push Feed direction Push Feed direction Push Feed direction Push
Hand of toolholder Right Hand of toolholder Left Hand of toolholder Right Hand of toolholder Left
Hand of insert Right Hand of insert Left Hand of insert Right Hand of insert Left
Standard shim q Standard shim w Standard shim w Standard shim q

Work rotation Regular Work rotation Reverse Work rotation Reverse Work rotation Regular
Threading Tool

Feed direction Pull Feed direction Pull Feed direction Pull Feed direction Pull
Hand of toolholder Left Hand of toolholder Right Hand of toolholder Left Hand of toolholder Right
Hand of insert Left Hand of insert Right Hand of insert Left Hand of insert Right
Standard shim r Standard shim e Standard shim e Standard shim r

Standard shim
No. New No. New
A16-1DT A16-1DT
A16-1 A16-1
q GX22-1DT w GX22-1DT
NXE22-1 NXN22-1
NXE27-1 NXN27-1
Work rotation Reverse Work rotation Regular
Feed direction Push Feed direction Push AE16-99DT AN16-99DT
Hand of toolholder Right Hand of toolholder Left AE16-99 AN16-99
Hand of insert Right Hand of insert Left
Standard shim q Standard shim w e GXE22-99DT r GXN22-99DT
NXE22-99 NXN22-99
NXE27-99 NXN27-99

Work rotation Reverse Work rotation Regular

Feed direction Pull Feed direction Pull
Hand of toolholder Left Hand of toolholder Right
Hand of insert Left Hand of insert Right
Standard shim r Standard shim e

B438 www.tungaloyamerica.com
 Fund am en t al s o f s crew t hread s

Relationship between lead, lead angle and pitch Thread angle Pitch P (large)
Thread height Pitch P (small) = lead
1. Lead is the axial distance a screw advances in one rotation. In single
start screw, the lead is equal to the pitch.
2. The inclination angle of a threaded groove is called lead angle. In screws
of the same diameter, the lead angle increases as the pitch increases.
3. The side face of a completed thread groove is called flank. The distance Lead angle
Flank (large)
between the crest and the root is called thread height. Lead angle (small)

Single and multi start thread

Lead
1. The single start thread has a single groove. Two start thread or three Two start thread Pitch
start thread has two grooves or three grooves respectively.
2. The pitch of multi start thread is the distance of adjoining groove.
3. When viewing the section of the multi start thread, the pitch is same as
that of the single start thread. The lead of the two or three start thread is
twice or three times the pitch. The multi start thread is mainly used for
trapezoidal threads.

Tolerance class of threads

Tolerance classes of screw threads are expressed as follows: by cutting or rolling, are generally used. 5H- and 4h-class
Metric coarse external thread: 6h, 6g Metric coarse internal threads (former JIS first class) are generally finished by
thread: 5H, 6H grinding.
These classes are ranked with tolerances of thread diameter, For example, M8-6g means metric coarse external thread of
pitch, thread angle, etc. For fastening applications, 6H- and 6g tolerance class.
6g-class (former JIS second class) threads, manufactured

Threading Tool
TAC threading insert
Difference between full-profile and partial-profile insert

Full-profile insert
In the full-profile insert, the major diameter of the thread is thread as shown in Figure below, these portions must be
finished by the profiled finishing edge as shown in Figure below. finished by another tool later.
Therefore, about 0.1 mm of finishing stock must be left on the Full-profile insert could produce no burr and good thread by the
outer surface of the workpiece before threading. In trapezoidal profiled finishing edge.
threads, since slants of 15º to 30º are left on the crest of the

Partial-profile insert Full-profile insert  When machining trapezoidal threads:

Trapezoidal thread
Thread Thread

Thread height
Finishing

Full-profile 15° ~ 30°

0.1~0.2

Partial-profile Crest (finished Surface turned insert Crest (finished

stock

in preceding in preceding with threading Portion to be

insert finished later
operation) operation insert)

Partial-profile insert For example

Partial-profile inserts can not be used for finishing of the Insert radius
Designation Pitch (mm) TPI rε (mm)
crest, but can be applied to a wide range of pitches.
16ERA60 0.5 ~ 1.5 48 ~ 16 0.06
16ERG60 1.75 ~ 3 14 ~ 8 0.22
Corner radii of inserts are fitted to the thread of the smallest pitch.

Tungaloy B439
 Fund am ent al s o f s crew t hread s

Difference between external and internal use inserts

In full-profile inserts for metric and unified threads, the corner radius and thread height differ from those for the external and
internal use insert respectively. Therefore, the right hand insert for external use and the left hand insert for internal use are not
the same tool.
Since the rake angles of toolholders are -10º for external toolholders and -15º for internal toolholders, the external / internal
toolholders can not be used for machining internal / external thread.
In Whitworth thread, though the external thread and internal thread have the same thread form, the external and internal
toolholders are incompatible because of the different rake angle.

For example
Applicable Insert radius Thread hight Rake angle of
Designation rε (mm)
inserts h (mm) holders
16ER20ISO External 0.25 1.52 -10°
16IL20ISO Internal 0.14 1.3 -15°
Threading Tool

B440 www.tungaloyamerica.com
 Shi m rep l a cement met ho d o f ST- typ e to o ls

Compensation for the lead angle and tool relief angle

When the pitch is large or the screw diameter is small, the
lead angle becomes large and the effective relief angle on the Thread angle Pitch P (large)
Pitch P (small) = lead
advance flank side β2 becomes small. In particular, this will Thread height

cause shorter life of the insert in the case of trapezoidal screw

with small flank angle. It is ideal without any interference for
the thread cutting insert to have an equal relief angle on both
right and left. Replace the shim so that the rake face of insert Lead angle
faces the thread groove direction (that is, β = β3). Flank (large)
Lead angle (small)

Calculating the lead angle

α
The lead angle is calculated as follows:
β: Lead angle
β = tan -1( R/πd) = tan -1( nP/πd) R: Lead Shim Insert

I
n: No. of threads θ
P: Pitch
Toolholder
d: Pitch diameter
Calculating the relief angle P Thread
groove
The relief angle β1 is calculated as follows:

β3
Lead angle
Pitch compensation
diameter d

1
°-β
β1 = tan -1 (tanθ • tan α )
Insert

90
Small clearance
(Possibility of β2
interference)
Shim
The α of a standard toolholder is 10˚ for external threading and
15˚ for internal threading. β
β
I–I cross section

Included angle β1
2θ θ ød (Pitch diameter)
External threading tool Internal threading tool

Threading Tool
60° 30° 5.8° 8.8°
55° 27.5° 5.2° 7.9°
30° 15° 2.7° 4.1°
29° 14.5° 2.6° 4°
β

P
Accordingly, the effective relief angle is calculated as follows: πd

β : Lead angle
β2 = β1 + β3 - β β2 : Effective relief angle
β3 : Lead angle
compensation value
In other words, β1 = β2 when the thread lead angle is equal
to the compensation value. Namely, the relief angle of the
tool itself is equal to the effective relief angle. If the wrong
compensation value is used, β1 > β2. The effective relief angle
becomes smaller and cause the interference between the
frank side of insert and the thread groove. Therefore, carry 3° 2°
1° 1°
out com-pensation of the lead angle so that the following
range is obtained:
±1˚ when the thread angle is 60˚ and 55˚ Standard Compensated
Compensated Standard Compensated
Compensated
±30´ when the thread angle is 30˚ and 29˚

Compensation of lead angle for shim less internal toolholders

When using internal threading toolholders without shim, the designation (-2 or -3) indicates 2° or 3° lead angle to be
the above-mentioned method can not be applied for lead used respectively. The toolholders without these figures are
angle compensation. Therefore, special toolholders for large for 1° lead angle.
lead angles are available as shown below. The final figure of

1° 2° 3°

SNR0016M16 SNR0016M16-2 SNR0016M16-3

Tungaloy B441
 Shi m rep l acement met ho d o f ST-t yp e to o ls

Type of shim and the compensation value of lead angle

Compensated lead
angles -2° -1° 0° 1° 2° 3° 4°
The designation of the shim
and compensated lead Shim -98 -99 -0 -1 -2 -3 -4
angles are shown in the table. Note: The last numeral of the shim designation is the compensated lead angle.

Clamp-on type toolholders

 Toolholders and applicable shims Shim
Toolholder designation
Screw-on / clamp-on dual toolholders R L
CER/L16-T AE16- AN16-
Shim CER/L22-T NXE22- NXN22-
Toolholder designation
R L CER/L27-T NXE27- NXN27-
CER/L16DT AE16-DT AN16-DT CNR/L16 AN16- AE16-
CER/L22DT GXE22-DT GXN22-DT CNR/L22 NXN22- NXE22-
TCNR/L16DT AN16-DT AE16-DT CNR/L27 NXN27- NXE27-
TCNR/L22DT GXN22-DT GXE22-DT B-CER/L16 AE16- AN16-
Note: Standard shim is AE16-1DT or GX22-1DT. Other types are optional. Note: Standard shim is -1. Other types are optional.

Shim selection guide for screw-on / clamp-on dual ST-type tools

Need special toolholders

6 4
TPI (Thread per Inch)

5 5
Threading Tool

*Pitch (mm)

4 6  List of exchangeable shims

3 Standard shim 8 Designation D30 Designation D30 Designation D30 Designation D30
A16-1DT
10 β3 = 4° AE16-4DT 䖃 AN16-4DT 䖃 GXE22-4DT 䖃 GXN22-4DT 䖃
2 12 β3 = 3°
GX22-1DT
16
AE16-3DT 䖃 AN16-3DT 䖃 GXE22-3DT 䖃 GXN22-3DT 䖃
1 (Used for both external 24 β3 = 2° AE16-2DT 䖃 AN16-2DT 䖃 GXE22-2DT 䖃 GXN22-2DT 䖃
and internal ) β3 = 1° Standard shim A16-1DT 䖃 A16-1DT 䖃 GX22-1DT 䖃 GX22-1DT 䖃
50 100 150 β3 = 0° AE16-0DT 䖃 AN16-0DT 䖃 GXE22-0DT 䖃 GXN22-0DT 䖃
Pich diameter (ød) β3 = -1° AE16-99DT 䖃 AN16-99DT 䖃 GXE22-99DT 䖃 GXN22-99DT 䖃
β3 = -2° AE16-98DT 䖃 AN16-98DT 䖃 GXE22-98DT 䖃 GXN22-98DT 䖃
* For the multi start thread lead (multiplied by the pitch
Applicable CER--16DT CEL--16DT CER--22DT CEL--22DT
and No. of threads) toolholders TCNL--16DT TCNR--16DT TCNL--22DT TCNR--22DT

Shim selection guide for clamp-on type ST-tools

Need special toolholders

6 4

5
TPI (Thread per Inch)

5
*Pitch (mm)

4 6  List of exchangeable shims

3 8 Designation D30 Designation D30 Designation D30 Designation D30 Designation D30 Designation D30
Standard shim
10 β3 = 4° AE16-4 䖃 AN16-4 䖃 NXE22-4 䖃 NXN22-4 䖃 NXE27-4 NXN27-4
2 A16-1
NXE22-1, NXN22-1
12 β3 = 3° AE16-3 䖃 AN16-3 䖃 NXE22-3 䖃 NXN22-3 䖃 NXE27-3 NXN27-3
16
1 NXE27-1, NXN27-1 β3 = 2° AE16-2 䖃 AN16-2 䖃 NXE22-2 䖃 NXN22-2 䖃 NXE27-2 NXN27-2
24
β3 = 1° Standard shim A16-1 䖃 A16-1 䖃 NXE22-1 䖃 NXN22-1 䖃 NXE27-1 䖃 NXN27-1 䖃
β3 = 0° AE16-0 䖃 AN16-0 䖃 NXE22-0 䖃 NXN22-0 䖃 NXE27-0 NXN27-0
50 100 150
β3 = -1° AE16-99 䖃 AN16-99 䖃 NXE22-99 䖃 NXN22-99 䖃 NXE27-99 NXN27-99
Pich diameter (ød)
β3 = -2° AE16-98 䖃 AN16-98 䖃 NXE22-98 䖃 NXN22-98 䖃 NXE27-98 NXN27-98
* For the multi start thread lead (multiplied by the pitch CER--16T CEL--16T CER--22T CEL--22T CER--27T CEL--27T
Applicable
and No. of threads) CNL--16 CNR--16 CNL--22 CNR--22 CNL--27 CNR--27
toolholders
B-CER--16 B-CEL--16

䖃 : Line up

B442 www.tungaloyamerica.com
 Sel ect i on o f ST- t y p e To o l ho l d ers

Selection of internal threading toolholders

Relation between internal toolholders and machinable threads
In the tables starting from next page, the relationships between toolholders,
inserts, threads to be machined, and shims to be replaced are shown. In these
tables, the criteria are set as follows. Symbols
¡The minimum machining diameter.
¡The L/D ratio of the toolholder. Recommended
¡The lead angle of the thread.
Usable
¡Cutting conditions
Especially when machining near the minimum machining diameter, the x Needs replacing of the shim.
compensation for the lead angle should be done carefully. "2" indicates "Change to the shim
Moreover, in threading, because chips generally can not be broken into small for 2° lead angle".
pieces, the shank size should be selected in consideration of adequate
clearance (C1).  Unusable

Internal diameter
Clearance C1

Stock to be removed with full-profile insert.

of thread
C1

C1 ≥ 3 mm Internal thread
( 1 mm for 6IR insert holders)

external thread

Pitch diameter

internal thread
Minor dia. of

Minor dia. of
hole diameter
External

Prepared
R thread
Overhang ratio L/D

shank
Steel

L/D ≤ 2¬
ød

øD

Carbide

Threading Tool
shank

C2
L/D ≤ 3¬ Internal thread
L

How to use the tables

qFirstly, find the nominal thread diameter. Example: M35 X 1.5
wThe table indicates that the lead angle is 0°48ߙ.
eThe Cat. No. of the insert to be used corresponds with IR15ISO.
rBy following the row to the right, and marks are found. The mark indicates the optimum toolholder type. The
toolholders of mark are usable, but less rigid because the shank diameter against the threading diameter is smaller than
those of marked toolholder. In this example, CNR0025R16 and TCNR0020R16DT are the optimum toolholders.
The insert Cat.No. is 16IR15ISO.
tIn the case of M33 X 3 thread, the lead angle is 1°46ߙ. By following the row to the right. x mark is found. This indicates that
the shim should be replaced to 2° type. For calculation of the lead angle, refer to page B441.

Metric fine screw thread (ISO) (For full size of this table, see page B445.)
Steel shank Carbide shank
Effective diameter

Shank material “Tsuppari-Ichiban”

Insert size 6IR 11IR 16IR 22IR 6IR 11IR 16IR 16IR 22IR
Nominal size

SNR0010M11SC

SNR0016R16SC-2

(TCNR0032T16DT)
SNR0006H06-2
SNR0006H06-3
SNR0008H06-2
SNR0008H06-3

SNR0016M16-2

SNR0016R16SC

TCNR0025S22DT
SNR0013L11-2

SNR0012P11SC-2

Holder
SNR0020Q22-2

SNR0006K06SC-2
SNR0006K06SC-3
SNR0008K06SC-2
SNR0008K06SC-3

SNR0012P11SC

TCNR0025S16DT
SNR0010K11-2

SNR0010M11SC-2

TCNR0020R16DT
TSNR0016Q16

TSNR0020R22
SNR0016M16

CNR0025R16

SNR0020Q22

CNR0025R22
Lead angle

CNR0020P16

CNR0032S16

CNR0032S22
SNR0010K11

Cat. No.
SNR0013L11
Pitch

Insert
Cat. No.
M33⫻1.5 1.5 32.03 0º51´ IR15ISO
M33⫻2 2 31.7 1º09´ IR20ISO
M33⫻3 3 31.05 1º46´ IR30ISO ™ ™
M35⫻1.5 1.5 34.03 0º48´ IR15ISO
M36⫻1.5 1.5 35.03 0º47´ IR15ISO
M36⫻2 2 34.7 1º03´ IR20ISO
M36⫻3 3 34.05 1º36´ IR30ISO ™ ™
M38⫻1.5 1.5 37.03 0º44´ IR15ISO
M39⫻1.5 1.5 38.03 0º43´ IR15ISO

Tungaloy B443
 Sel ect i o n o f ST- t y p e To o l ho l d er s
Selection of Internal Toolholders—Relationship between thread sizes, toolholders, and inserts—Part 1
Metric coarse screw thread (ISO)
“Tsuppari-
Shank material Steel shank Carbide shank Ichiban”

Insert size 6IR 11IR 16IR 22IR 27IR 6IR 11IR 16IR 22IR

Pitch diameter
Nominal size

Holder

SNR0016M16-2

SNR0016M16-3

SNR0010M11SC-2

SNR0010M11SC-3

(TCNR0032T22DT)
SNR0016R16SC-2

(SNR0016R16SC-3)
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

TCNR0025S22DT
SNR0020Q22-2

SNR0020Q22-3
SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3

SNR0010K11-2

SNR0010K11-3

SNR0013L11-2

SNR0013L11-3
Lead angle

(CNR0050U27)
Pitch (mm)

(CNR0040T22)
Cat. No.

CNR0025R22

CNR0032S22

CNR0040T27
(mm)
Insert
Cat. No.
M10 1.5 9.03 3º02´ IR15ISO
M11 1.5 10.03 2º44´ IR15ISO
M12 1.75 10.86 2º56´ IR175ISO
M14 2 12.7 2º52´ IR20ISO
M16 2 14.7 2º29´ IR20ISO
M18 2.5 16.38 2º47´ IR25ISO
M20 2.5 18.38 2º29´ IR25ISO
M22 2.5 20.38 2º14´ IR25ISO
M24 3 22.05 2º29´ IR30ISO
M27 3 25.05 2º11´ IR30ISO
M30 3.5 27.73 2º18´ IR35ISO
M33 3.5 30.73 2º05´ IR35ISO
M36 4 33.4 2º11´ IR40ISO
M39 4 36.4 2º00´ IR40ISO ™ ™
M42 4.5 39.08 2º06´ IR45ISO ™ ™
M45 4.5 42.08 1º57´ IR45ISO ™ ™
M48 5 44.75 2º02´ IR50ISO ™ ™ ™ ™
M52 5 48.75 1º52´ IR50ISO ™ ™ ™ ™
M56 5.5 52.43 1º55´ IR55ISO
M60 5.5 56.43 1º47´ IR55ISO ™
M64 6 60.1 1º49´ IR60ISO ™
Threading Tool

M68 6 64.1 1º42´ IR60ISO ™ ™

x : Change the shim to NXN22-2
x : Change the shim to NXN27-2 x : Change the shim to GXN22-2DT
Metric fine screw thread (ISO) 1/4
Shank material Steel shank Carbide shank
Insert size 6IR 11IR 6IR 11IR
Pitch diameter
Nominal size

SNR0010M11SC-2
SNR0010M11SC

SNR0012P11SC-2

SNR0012P11SC-3
Holder
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

SNR0010M11SC-3
SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3

SNR0010K11-2

SNR0010K11-3

SNR0012P11SC
SNR0013L11-2

SNR0013L11-3
Lead angle
Pitch (mm)

Cat. No.
SNR0010K11

SNR0013L11
(mm)

Insert
Cat. No.
M9⫻0.75 0.75 8.51 1º36´ IR075ISO
M9⫻1 1 8.32 2º11´ IR10ISO
M10⫻0.75 0.75 9.51 1º26´ IR075ISO
M10⫻1 1 9.35 1º57´ IR10ISO
M10⫻1.25 1.25 9.19 2º29´ IR125ISO
M11⫻0.75 0.75 10.51 1º18´ IR075ISO
M11⫻1 1 10.35 1º46´ IR10ISO
M12⫻1 1 11.35 1º36´ IR10ISO
M12⫻1.25 1.25 11.19 2º02´ IR125ISO
M12⫻1.5 1.5 11.03 2º29´ IR15ISO
M14⫻1 1 13.35 1º22´ IR10ISO
M14⫻1.25 1.25 13.19 1º44´ IR125ISO
M14⫻1.5 1.5 13.03 2º06´ IR15ISO
M15⫻1 1 14.35 1º16´ IR10ISO
M15⫻1.5 1.5 14.03 1º57´ IR15ISO
M16⫻1 1 15.35 1º11´ IR10ISO
M16⫻1.5 1.5 15.03 1º49´ IR15ISO
M17⫻1 1 16.35 1º07´ IR10ISO
M17⫻1.5 1.5 16.03 1º42´ IR15ISO
M18⫻1 1 17.35 1º03´ IR10ISO
M18⫻1.5 1.5 17.03 1º36´ IR15ISO
M18⫻2 2 16.7 2º11´ IR20ISO
M20⫻1 1 19.35 0º57´ IR10ISO
M20⫻1.5 1.5 19.03 1º26´ IR15ISO
M20⫻2 2 18.7 1º57´ IR20ISO

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

B444 www.tungaloyamerica.com
 Metric fine screw thread (ISO) 2/4
“Tsuppari-
Shank material Steel shank Carbide shank Ichiban”

Insert size 6IR 11IR 16IR 6IR 11IR 16IR 16IR

Pitch diameter
Nominal size
Holder

(SNR0016R16SC-3)
SNR0012P11SC-2

SNR0012P11SC-3
SNR0010M11SC-2

SNR0010M11SC-3
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

SNR0016R16SC-2
SNR0010M11SC

TCNR0020R16DT

TCNR0025S16DT
SNR0016R16SC
SNR0012P11SC
Lead angle

SNR0016M16-2

SNR0016M16-3
SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3
Pitch (mm)

SNR0010K11-2

SNR0013L11-2

SNR0013L11-3

TSNR0016Q16
Cat. No.

SNR0016M16

CNR0020P16
SNR0010K11

SNR0013L11
(mm)
Insert
Cat. No.
M22⫻1 1 21.35 0º51´ IR10ISO
M22⫻1.5 1.5 21.03 1º18´ IR15ISO
M22⫻2 2 20.7 1º46´ IR20ISO
M24⫻1 1 23.35 0º47´ IR10ISO
M24⫻1.5 1.5 23.03 1º11´ IR15ISO
M24⫻2 2 22.07 1º39´ IR20ISO
M25⫻1 1 24.35 0º45´ IR10ISO
M25⫻1.5 1.5 24.03 1º08 IR15ISO
M25⫻2 2 23.7 1º32´ IR20ISO
M26⫻1.5 1.5 25.03 1º06´ IR15ISO
M27⫻1 1 26.35 0º42´ IR10ISO
M27⫻1.5 1.5 26.03 1º03´ IR15ISO
M27⫻2 2 25.7 1º25´ IR20ISO
M28⫻1 1 27.35 0º40´ IR10ISO
M28⫻1.5 1.5 27.03 1º01´ IR15ISO
M28⫻2 2 26.7 1º22´ IR20ISO
M30⫻1 1 29.35 0º37´ IR10ISO
M30⫻1.5 1.5 29.03 0º57´ IR15ISO
M30⫻2 2 28.7 1º16´ IR20ISO
M30⫻3 3 28.05 1º57´ IR30ISO
M32⫻1.5 1.5 31.03 0º53´ IR15ISO
M32⫻2 2 30.07 1º11´ IR20ISO

Threading Tool
Metric fine screw thread (ISO) 3/4
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Insert size 6IR 11IR 16IR 22IR 6IR 11IR 16IR 16IR 22IR
Pitch diameter
Nominal size

Holder
SNR0010M11SC

SNR0016R16SC-2

(TCNR0032T16DT)
SNR0006H06-2
SNR0006H06-3
SNR0008H06-2
SNR0008H06-3

SNR0016M16-2

SNR0016R16SC

TCNR0025S22DT
SNR0013L11-2

SNR0012P11SC-2
SNR0020Q22-2

SNR0006K06SC-2
SNR0006K06SC-3
SNR0008K06SC-2
SNR0008K06SC-3

SNR0012P11SC

TCNR0025S16DT
SNR0010K11-2

SNR0010M11SC-2

TCNR0020R16DT
TSNR0016Q16

TSNR0020R22
Lead angle
Pitch (mm)

SNR0016M16

Cat. No.
CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22
SNR0010K11

SNR0013L11
(mm)

Insert
Cat. No.
M33⫻1.5 1.5 32.03 0º51´ IR15ISO
M33⫻2 2 31.7 1º09´ IR20ISO
M33⫻3 3 31.05 1º46´ IR30ISO ™ ™
M35⫻1.5 1.5 34.03 0º48´ IR15ISO
M36⫻1.5 1.5 35.03 0º47´ IR15ISO
M36⫻2 2 34.7 1º03´ IR20ISO
M36⫻3 3 34.05 1º36´ IR30ISO ™ ™
M38⫻1.5 1.5 37.03 0º44´ IR15ISO
M39⫻1.5 1.5 38.03 0º43´ IR15ISO
M39⫻2 2 38.7 0º58´ IR20ISO
M39⫻3 3 37.05 1º29´ IR30ISO
M40⫻1.5 1.5 39.03 0º42´ IR15ISO
M40⫻2 2 37.8 0º57´ IR20ISO
M40⫻3 3 38.05 1º26´ IR30ISO
M42⫻1.5 1.5 41.03 0º40´ IR15ISO
M42⫻2 2 40.7 0º54´ IR20ISO
M42⫻3 3 40.05 1º22´ IR30ISO
M42⫻4 4 39.4 1º51´ IR40ISO ™ ™
M45⫻1.5 1.5 44.03 0º37´ IR15ISO
M45⫻2 2 43.7 0º50´ IR20ISO
M45⫻3 3 43.05 1º16´ IR30ISO
M45⫻4 4 42.4 1º43´ IR40ISO ™ ™
M48⫻1.5 1.5 47.03 0º35´ IR15ISO
M48⫻2 2 46.7 0º47´ IR20ISO
M48⫻3 3 46.05 1º11´ IR30ISO
M48⫻4 4 45.4 1º36´ IR40ISO ™ ™
x : Change the shim to AN16-2 x : Change the shim to AN16-2DT
x : Change the shim to NXN22-2 x : Change the shim to GXN22-2DT

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

Tungaloy B445
 Sel ect i o n o f ST- t y p e To o l ho l d er s

Metric fine screw thread (ISO) 4/4

Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Insert size 6IR 11IR 16IR 22IR 6IR 11IR 16IR 16IR 22IR

Pitch diameter
Nominal size
Holder

(TCNR0032T16DT)

(TCNR0032T22DT)
SNR0020Q22-2

SNR0016R16SC-2
TSNR0016Q16
SNR0006H06-2
SNR0006H06-3
SNR0008H06-2
SNR0008H06-3

SNR0006K06SC-2
SNR0006K06SC-3
SNR0008K06SC-2
SNR0008K06SC-3
SNR0010M11SC

SNR0016R16SC
SNR0010M11SC-2

SNR0012P11SC-2
SNR0010K11-2

(CNR0050U16)

SNR0012P11SC

TSNR0020R22
TCNR0020R16DT
SNR0016M16-2

TCNR0025S16DT

TCNR0025S22DT
(CNR0040T16)

(CNR0040T22)
SNR0013L11-2
Lead angle

SNR0016M16
Pitch (mm)

CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22
SNR0010K11
Cat. No.

SNR0013L11
(mm)
Insert
Cat. No.
M50⫻1.5 1.5 49.03 0º33´ IR15ISO
M50⫻2 2 48.7 0º45´ IR20ISO
M50⫻3 3 48.05 1º08´ IR30ISO
M52⫻1.5 1.5 51.03 0º32´ IR15ISO
M52⫻2 2 50.7 0º43´ IR20ISO
M52⫻3 3 50.05 1º06´ IR30ISO
M52⫻4 4 49.4 1º29´ IR40ISO
M55⫻1.5 1.5 54.03 0º30´ IR15ISO
M55⫻2 2 53.7 0º41´ IR20ISO
M55⫻3 3 53.05 1º02´ IR30ISO
M55⫻4 4 52.4 1º24´ IR40ISO
M56⫻1.5 1.5 55.03 0º30´ IR15ISO
M56⫻2 2 54.7 0º40´ IR20ISO
M56⫻3 3 54.05 1º01´ IR30ISO
M56⫻4 4 53.4 1º22´ IR40ISO
M58⫻1.5 1.5 57.03 0º29´ IR15ISO
M58⫻2 2 56.7 0º39´ IR20ISO
M58⫻3 3 56.05 0º59´ IR30ISO
M58⫻4 4 55.4 1º19´ IR40ISO
M60⫻1.5 1.5 59.03 0º28´ IR15ISO
M60⫻2 2 58.7 0º37´ IR20ISO
M60⫻3 3 58.05 0º57´ IR30ISO
M60⫻4 4 57.4 1º16´ IR40ISO
Threading Tool

Unified coarse screw thread (UNC)

“Tsuppari-
Shank material Steel shank Carbide shank
Pitch diameter (in)

Ichiban”

Insert size 11IR 16IR 22IR 27IR 11IR 16IR 22IR

Nominal size

SNR0016M16-2

SNR0016M16-3

SNR0010M11SC-2

SNR0010M11SC-3
Holder
SNR0010M11SC

TCNR0025S22DT

(TCNR0032T22DT)
SNR0016R16SC-2

(SNR0016R16SC-3)
SNR0012P11SC-2

SNR0012P11SC-3
SNR0020Q22-2

SNR0020Q22-3

SNR0016R16SC
SNR0012P11SC
SNR0010K11-2

SNR0010K11-3

SNR0013L11-2

SNR0013L11-3
Lead angle

(CNR0050U27)

(CNR0063V27)
(CNR0040T22)

Cat. No.
SNR0016M16

SNR0020Q22

CNR0025R22

CNR0032S22
SNR0010K11

CNR0040T27
SNR0013L11
TPI

Insert
Cat. No.
7/16-14UNC 14 0.3911 3º20´ (IR14UN)
1/2-13UNC 13 0.4500 3º07´ (IR13UN)
9/16-12UNC 12 0.5084 2º59´ IR12UN
5/8-11UNC 11 0.5660 2º56´ (IR11UN)
3/4-10UNC 10 0.6850 2º40´ (IR10UN)
7/8-9UNC 9 0.8028 2º31´ IR9UN
1-8UNC 8 0.9188 2º29´ IR8UN
1 1/8-7UNC 7 1.0322 2º31´ (IR7UN)
1 1/4-7UNC 7 1.1572 2º15´ (IR7UN)
1 3/8-6UNC 6 1.2667 2º24´ (IR6UN)
1 1/2-6UNC 6 1.3917 2º11´ (IR6UN) ™ ™
1 3/4-5UNC 5 1.6201 2º15´ (IR5UN) ™ ™
2-4 1/2UNC 4.5 1.8557 2º11´ (IR45UN)
2 1/4-4 1/2UNC 4.5 2.1057 1º55´ (IR45UN) ™
2 1/2-4UNC 4 2.3376 1º57´ (IR4UN) ™
2 3/4-4UNC 4 2.5876 1º46´ (IR4UN) ™ ™
3-4UNC 4 2.8376 1º36´ (IR4UN) ™ ™
3 1/4-4UNC 4 3.0876 1º29´ (IR4UN)
3 1/2-4UNC 4 3.3376 1º22´ (IR4UN)
3 3/4-4UNC 4 3.5876 1º16´ (IR4UN)
4-4UNC 4 3.8376 1º11´ (IR4UN)
x : Change the shim to NXN22-2 x : Change the shim to GXN22-2DT
x : Change the shim to NXN27-2
Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

B446 www.tungaloyamerica.com
 Unified fine screw thread (UNF)
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”

Pitch diameter (in)

Insert size 6IR 11IR 16IR 6IR 11IR 16IR 16IR

Nominal size
Holder

SNR0016R16SC-2
SNR0016M16-2

SNR0010M11SC-2
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

SNR0012P11SC

SNR0012P11SC-2
SNR0010M11SC

SNR0016R16SC

TCNR0020R16DT

TCNR0025S16DT
SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3

SNR0010K11-2

SNR0013L11-2
Lead angle

TSNR0016Q16
Cat. No.

SNR0016M16

CNR0025R16
CNR0020P16
TPI Insert
Cat. No.

(IR24UN)
3/8-24UNF 24 0.3479 2º11´
IRA60

(IR20UN)
7/16-20UNF 20 0.4050 2º15´
IRA60

(IR20UN)
1/2-20UNF 20 0.4675 1º57´
IRA60

(IR18UN)
9/16-18UNF 18 0.5264 1º55´
IRA60

(IR18UN)
5/8-18UNF 18 0.5889 1º43´
IRA60

3/4-16UNF 16 0.7094 1º36´ IR16UN

7/8-14UNF 14 0.8286 1º34´ IR14UN

1-12UNF 12 0.9459 1º36´ IR12UN

1 1/8-12UNF 12 1.0709 1º25´ IR12UN

1 1/4-12UNF 12 1.1959 1º16´ IR12UN

1 3/8-12UNF 12 1.3209 1º09´ IR12UN

1 1/2-12UNF 12 1.4459 1º03´ IR12UN

Threading Tool
Unified extra fine screw thread (UNEF)
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Pitch diameter (in)

Insert size 6IR 11IR 16IR 6IR 11IR 16IR 16IR

Nominal size

Holder
SNR0006H06SC-2

SNR0008H06SC-2
SNR0016M16-2

SNR0016M16-2

TCNR0020R16DT

TCNR0025S16DT
SNR0006H06-2

SNR0008H06-2

SNR0010K11-2

SNR0010K11-2
SNR0013L11-2

SNR0012L11-2
Lead angle

TSNR0016Q16
Cat. No.
SNR0016M16

SNR0016M16
CNR0025R16
CNR0020P16

CNR0032S16
SNR0010K11

SNR0010K11
SNR0013L11

SNR0012L11
TPI

Insert
Cat. No.
3/8 32 0.3547 1º61´ IR32UN
7/16 28 0.4143 1º57´ IR28UN
1/2 28 0.4768 1º37´ IR28UN
9/16 24 0.5354 1º42´ IR24UN
5/8 24 0.5979 1º27´ IR24UN
11/16 24 0.6604 1º15´ IR24UN
3/4 20 0.7175 1º27´ IR20UN
13/16 20 0.7800 1º17´ IR20UN
7/8 20 0.8425 1º08´ IR20UN
15/16 20 0.9050 1º01´ IR20UN
1 20 0.9675 0º94´ IR20UN
1 1/16 18 1.0264 0º99´ IR18UN
1 1/8 18 1.0889 0º93´ IR18UN
1 3/16 18 1.1514 0º88´ IR18UN
1 1/4 18 1.2139 0º84´ IR18UN
1 5/16 18 1.2764 0º79´ IR18UN
1 3/8 18 1.3389 0º76´ IR18UN
1 7/16 18 1.4014 0º72´ IR18UN
1 1/2 18 1.4639 0º69´ IR18UN
1 9/16 18 1.5264 0º66´ IR18UN
1 5/8 18 1.5889 0º64´ IR18UN
1 11/16 18 1.6514 0º61´ IR18UN

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

Tungaloy B447
 S el ecti o n o f ST- t y p e To o l ho l d er s

Whitworth British Standard (BSW)

Shank material Steel shank Carbide shank “Tsuppari-Ichiban”

Pitch diameter (in)

Insert size 16IR 22IR 16IR 16IR 22IR
Nominal size Holder

SNR0016M16-2

SNR0016M16-3

SNR0016M16-2

TCNR0020R16DT

TCNR0025S16DT

TCNR0025S22DT
SNR0020Q22-2

SNR0020Q22-3
Lead angle

TSNR0016Q16

TSNR0020R22
Cat. No.

SNR0016M16

SNR0016M16
CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22
TPI
Insert
Cat. No.
7/16 14 0.3918 3º32´ IR14W

1/2 12 0.4466 3º40´ IR12W

9/16 12 0.5091 2º98´ IR12W

5/8 11 0.5668 2º92´ IR11W

11/16 11 0.6293 2º63´ IR11W

3/4 10 0.6860 2º66´ IR10W

7/8 9 0.8039 2º52´ IR9W

1 8 0.9200 2º48´ IR8W

1 1/8 7 1.0335 2º52´ IR7W

1 1/4 7 1.1585 2º25´ IR7W

1 1/2 6 1.3933 2º18´ IR6W

1 3/4 5 1.6219 2º25´ IR5W

™ ™

x : Change the shim to NXN22-2 x : Change the shim to GXN22-2DT

Threading Tool

Whitworth British Standard Fine (BSF)

Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Pitch diameter (in)

Insert size 6IR 11IR 16IR 22IR 6IR 16IR 16IR 22IR
Nominal size

Holder
SNR0006H06SC-2

SNR0008H06SC-2
SNR0016M16-2

SNR0016M16-3

SNR0016M16-2

TCNR0020R16DT

TCNR0025S16DT

TCNR0025S22DT
SNR0020Q22-2

SNR0020Q22-3
SNR0006H06-2

SNR0008H06-2

SNR0010K11-2
Lead angle

TSNR0016Q16

TSNR0020R22
Cat. No.
SNR0016M16

SNR0016M16
CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S22
SNR0010K11
TPI

Insert
Cat. No.
7/16 18 0.4019 2º52´ IR18W
1/2 16 0.4600 2º48´ IR16W
9/16 16 0.5225 2º18´ IR16W
5/8 14 0.5793 2º25´ IR14W
11/16 14 0.6418 2º03´ IR14W
3/4 12 0.6966 2º18´ IR12W
7/8 11 0.8168 2º03´ IR11W
1 10 0.9360 1º95´ IR10W
1 1/8 9 1.0539 1º92´ IR9W
1 1/4 9 1.1789 1º72´ IR9W ™ ™
1 3/8 8 1.2950 1º76´ IR8W ™ ™
1 1/2 8 1.4200 1º61´ IR8W ™ ™
1 5/8 8 1.5450 1º48´ IR8W
1 3/4 7 1.6585 1º57´ IR7W ™ ™
2 7 1.9085 1º37´ IR7W
2 1/4 6 2.1433 1º42´ IR6W
2 1/2 6 2.3933 1º27´ IR6W
2 3/4 6 2.6433 1º15´ IR6W
3 5 2.8719 1º27´ IR5W
3 1/4 5 3.1219 1º17´ IR5W

x : Change the shim to AN16-2 x : Change the shim to AN16-2DT

x : Change the shim to NXN22-2 x : Change the shim to GXN22-2DT

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

B448 www.tungaloyamerica.com
 30° trapezoidal thread (TR) 1/2
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Insert size

Pitch diameter
16IR 22IR 27IR 16IR 16IR 22IR
Nominal size
Holder

SNR0016M16-2

SNR0016M16-3

(SNR0016R16SC-3)

(TCNR0032T16DT)

(TCNR0032T22DT)
TCNR0020R16DT
SNR0020Q22-2

SNR0020Q22-3

SNR0016R16SC-2
SNR0016R16SC

TCNR0025S16DT

TCNR0025S22DT
(CNR0050U27)

TSNR0016Q16

TSNR0020R22
Lead angle
Pitch (mm)

SNR0016M16

CNR0050U16
CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22
Cat. No.

CNR0040T16

CNR0040T27
(mm)
Insert
Cat. No.
TR22⫻3 3 20.5 2º40´ IR30TR
TR24⫻5 5 21.5 4º14´ IR50TR
TR24⫻3 3 22.5 2º26´ IR30TR
TR26⫻5 5 23.5 3º52´ IR50TR
TR26⫻3 3 24.5 2º14´ IR30TR
TR28⫻5 5 25.5 3º34´ IR50TR
TR28⫻3 3 26.5 2º04´ IR30TR
TR30⫻6 6 27 4º03´ IR60TR
TR30⫻3 3 28.5 1º55´ IR30TR
TR32⫻6 6 29 3º46´ IR60TR
TR32⫻3 3 30.5 1º48´ IR30TR ™ ™
TR34⫻6 6 31 3º32´ IR60TR
TR34⫻3 3 32.5 1º41´ IR30TR ™ ™
TR36⫻6 6 33 3º19´ IR60TR
TR36⫻3 3 34.5 1º35´ IR30TR 2 ™ ™ ™
TR38⫻3 3 36.5 1º30´ IR30TR 2 ™ ™ ™
TR40⫻3 3 38.5 1º25´ IR30TR
TR42⫻3 3 40.5 1º21´ IR30TR
TR44⫻3 3 42.5 1º17´ IR30TR
TR46⫻3 3 44.5 1º14´ IR30TR
TR48⫻3 3 46.5 1º11´ IR30TR
TR50⫻3 3 48.5 1º08´ IR30TR
TR52⫻3 3 50.5 1º05´ IR30TR
TR55⫻3 3 53.5 1º01´ IR30TR
TR60⫻3 3 58.5 0º56´ IR30TR
x : Change the shim to AN16-2 x : Change the shim to AN16-2DT

Threading Tool
30° trapezoidal thread (TR) 2/2
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Insert size 16IR 22IR 27IR 16IR 16IR 22IR
Pitch diameter
Nominal size

Holder

(TCNR0032T16DT)
(SNR0016R16SC-3)

(TCNR0032T22DT)
SNR0016R16SC-2
SNR0016M16-2

SNR0016M16-3

SNR0016R16SC
SNR0020Q22-2

SNR0020Q22-3

TCNR0025S16DT

TCNR0025S22DT
TCNR0020R16DT
TSNR0016Q16
(CNR0050U22)

(CNR0050U27)
Lead angle

TSNR0020R22
(CNR0063V22)

(CNR0063V27)
(CNR0040T22)
Pitch (mm)

Cat. No.
SNR0016M16

CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22

CNR0040T27
(mm)

Insert
Cat. No.
TR65⫻4 4 63 1º09´ IR40TR
TR70⫻4 4 68 1º04´ IR40TR
TR75⫻4 4 73 1º00´ IR40TR
TR80⫻4 4 78 0º56´ IR40TR
TR85⫻4 4 83 0º53´ IR40TR
TR90⫻4 4 88 0º50´ IR40TR
TR95⫻4 4 93 0º47´ IR40TR
TR100⫻4 4 98 0º45´ IR40TR
TR105⫻4 4 103 0º42´ IR40TR
TR110⫻4 4 108 0º41´ IR40TR
TR115⫻6 6 112 0º59´ IR60TR
TR120⫻6 6 117 0º56´ IR60TR
TR125⫻6 6 122 0º54´ IR60TR
TR130⫻6 6 127 0º52´ IR60TR
TR135⫻6 6 132 0º50´ IR60TR
TR140⫻6 6 137 0º48´ IR60TR
TR145⫻6 6 142 0º46´ IR60TR
TR150⫻6 6 147 0º45´ IR60TR
TR155⫻6 6 152 0º43´ IR60TR
TR160⫻6 6 157 0º42´ IR60TR
TR165⫻6 6 162 0º41´ IR60TR
TR170⫻6 6 167 0º39´ IR60TR

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

Tungaloy B449
 Sel ect i o n o f ST- t y p e To o l ho l d er s

Parallel pipe thread (G) This table is also applied to PF, Rp, and PS type threads.
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”

Pitch diameter
Nominal size Insert size 6IR 11IR 16IR 6IR 11IR 16IR 16IR
Holder

SNR0012P11SC-2
SNR0006H06-2

SNR0008H06-2

SNR0016R16SC
SNR0016M16-2

SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

SNR0010M11SC

SNR0016R16SC-2

TCNR0020R16DT

(TCNR0032T16DT)
SNR0010M11SC-2
SNR0010K11-2

SNR0012P11SC

TCNR0025S16DT
SNR0013L11-2
Lead angle

TSNR0016Q16
(CNR0050U16)
(CNR0040T16)
SNR0016M16
Cat. No.

CNR0025R16
CNR0020P16

CNR0032S16
SNR0010K11

SNR0013L11
Pitch (in)

(mm)
TPI

Insert
Cat. No.
G1/4 19 0.053 12.30 1º59´ IR19W
G3/8 19 0.053 15.81 1º33´ IR19W
G1/2 14 0.071 19.79 1º40´ IR14W
G5/8 14 0.071 21.75 1º31´ IR14W
G3/4 14 0.071 25.28 1º18´ IR14W
G7/8 14 0.071 29.04 1º08´ IR14W
G1 11 0.091 31.77 1º20´ IR11W
G1-1/8 11 0.091 36.42 1º09´ IR11W
G1-1/4 11 0.091 40.43 1º02´ IR11W
G1-1/2 11 0.091 46.32 0º55´ IR11W
G1-3/4 11 0.091 52.27 0º48´ IR11W
G2 11 0.091 58.14 0º43´ IR11W
G2-1/4 11 0.091 64.23 0º39´ IR11W
G2-1/2 11 0.091 73.71 0º34´ IR11W
G2-3/4 11 0.091 80.06 0º32´ IR11W
G3 11 0.091 86.41 0º29´ IR11W 0 0 0 0 º 0 0 º
G3-1/2 11 0.091 98.85 0º26´ IR11W 0 0 0 0 º 0 0 º
G4 11 0.091 111.55 0º23´ IR11W 0 0 0 0 º 0 0 º
G4-1/2 11 0.091 124.25 0º20´ IR11W 0 0 0 0 º 0 0 º
G5 11 0.091 136.95 0º18´ IR11W 0 0 0 0 º 0 0 º
G6 11 0.091 162.35 0º16´ IR11W 0 0 0 0 º 0 0 º
/ : Change the shim to AN16-0 / : Change the shim to AN16-0DT

Taper pipe thread (PT) This table is also applied to Rc type pipe thread.
Threading Tool

Shank material Steel shank Carbide shank “Tsuppari-Ichiban”

Insert size 6IR 11IR 16IR 6IR 11IR 16IR 16IR
Pitch diameter
Nominal size

Holder
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3
SNR0016M16-2
SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3

SNR0016R16SC-2
SNR0010M11SC-2
SNR0010M11SC

SNR0012P11SC-2
SNR0010K11-2

SNR0016R16SC

(TCNR0032T16DT)
SNR0012P11SC

TCNR0020R16DT

TCNR0025S16DT
SNR0013L11-2

TSNR0016Q16
(CNR0050U16)
Lead angle

(CNR0040T16)

Cat. No.
SNR0016M16

CNR0025R16
CNR0020P16

CNR0032S16
SNR0010K11

SNR0013L11
Pitch (in)

(mm)
TPI

Insert
Cat. No.
PT1/4 19 0.053 12.30 1º59´ IR19PT

PT3/8 19 0.053 15.81 1º33´ IR19PT

PT1/2 14 0.071 19.79 1º40´ IR14PT

PT3/4 14 0.071 25.28 1º19´ IR14PT

PT1 11 0.091 31.77 1º20´ IR11PT

PT1 1/4 11 0.091 40.43 1º02´ IR11PT

PT1 1/2 11 0.091 46.32 0º55´ IR11PT

PT2 11 0.091 58.14 0º43´ IR11PT

PT2 1/2 11 0.091 73.71 0º34´ IR11PT

PT3 11 0.091 86.41 0º29´ IR11PT 0 0 0 0 º 0 0 º

PT3 1/2 11 0.091 98.85 0º26´ IR11PT 0 0 0 0 º 0 0 º
PT4 11 0.091 111.55 0º23´ IR11PT 0 0 0 0 º 0 0 º
PT5 11 0.091 136.95 0º18´ IR11PT 0 0 0 0 º 0 0 º
PT6 11 0.091 162.35 0º16´ IR11PT 0 0 0 0 º 0 0 º
PT7 11 0.091 187.75 0º13´ IR11PT 0 0 0 0 º 0 0 º
PT8 11 0.091 213.15 0º12´ IR11PT 0 0 0 0 º 0 0 º
PT9 11 0.091 238.55 0º11´ IR11PT 0 0 0 0 º 0 0 º
PT10 11 0.091 263.95 0º10´ IR11PT 0 0 0 0 º 0 0 º
PT12 11 0.091 314.75 0º08´ IR11PT 0 0 0 0 º 0 0 º

/ : Change the shim to AN16-0 / : Change the shim to AN16-0DT

Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

B450 www.tungaloyamerica.com
 National taper pipe thread (NPT)
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
Insert size 6IR 16IR 6IR 16IR 16IR
Nominal size
Holder

SNR0006H06-2

SNR0006H06-3

SNR0008H06-2

SNR0008H06-3

(TCNR0032T16DT)
SNR0016M16-2

SNR0016M16-3

(SNR0016R16SC-3)
SNR0016R16SC-2

TCNR0020R16DT
SNR0006K06SC-2

SNR0006K06SC-3

SNR0008K06SC-2

SNR0008K06SC-3

TCNR0025S16DT
SNR0016R16SC
(CNR0050U16)

TSNR0016Q16
(CNR0040T16)
Lead angle

SNR0016M16
Cat. No.

CNR0025R16
CNR0020P16

CNR0032S16
Pitch (in)
TPI Insert
Cat. No.
3/8NPT 18 0.056 1º37´ IR18NPT
1/2NPT 14 0.071 1º40´ IR14NPT
3/4NPT 14 0.071 1º19´ IR14NPT
1NPT 11.5 0.087 1º17´ IR115NPT
1 1/4NPT 11.5 0.087 1º00´ IR115NPT
1 1/2NPT 11.5 0.087 0º52´ IR115NPT
2NPT 11.5 0.087 0º41´ IR115NPT
2 1/2NPT 8 0.125 0º50´ IR8NPT
3NPT 8 0.125 0º40´ IR8NPT
3 1/2NPT 8 0.125 0º35´ IR8NPT
4NPT 8 0.125 0º31´ IR8NPT
5NPT 8 0.125 0º25´ IR8NPT 0 0 0 0 º 0 0 º
6NPT 8 0.125 0º21´ IR8NPT 0 0 0 0 º 0 0 º
8NPT 8 0.125 0º16´ IR8NPT 0 0 0 0 º 0 0 º
10NPT 8 0.125 0º13´ IR8NPT 0 0 0 0 º 0 0 º
12NPT 8 0.125 0º11´ IR8NPT 0 0 0 0 º 0 0 º
14NPT 8 0.125 0º10´ IR8NPT 0 0 0 0 º 0 0 º
16NPT 8 0.125 0º09´ IR8NPT 0 0 0 0 º 0 0 º
18NPT 8 0.125 0º08´ IR8NPT 0 0 0 0 º 0 0 º
20NPT 8 0.125 0º07´ IR8NPT 0 0 0 0 º 0 0 º
24NPT 8 0.125 0º06´ IR8NPT 0 0 0 0 º 0 0 º
/ : Change the shim to AN16-0 / : Change the shim to AN16-0DT

Threading Tool
29° trapezoidal thread (ACME)
Shank material Steel shank Carbide shank “Tsuppari-Ichiban”
16IR 22IR 27IR 16IR 16IR 22IR
Pitch diameter

Insert size
Nominal size

Holder

SNR0016R16SC-2

SNR0016R16SC-3
SNR0016M16-2

SNR0016M16-3

SNR0020Q22-2

SNR0020Q22-3

SNR0016R16SC

TCNR0020R16DT
TSNR0016Q16

(TCNR0032T22DT)
TCNR0025S22DT
(CNR0050U27)
Lead angle

SNR0016M16

CNR0025R16

SNR0020Q22

CNR0025R22
CNR0020P16

CNR0032S16

CNR0032S22

CNR0040T27

Cat. No.
Pitch (in)
TPI

(in)

Insert
Cat. No.

3/8 12 0.083 0.3333 4º33´ IR12ACME

7/16 12 0.083 0.3958 3º50´ IR12ACME

1/2 10 0.100 0.4500 4º03´ IR10ACME

5/8 8 0.125 0.5625 4º03´ IR8ACME

3/4 6 0.167 0.6667 4º33´ IR6ACME

7/8 6 0.167 0.7917 3º50´ IR6ACME

1 5 0.200 0.9000 4º03´ IR5ACME

1-1/8 5 0.200 1.0250 3º33´ IR5ACME

1-1/4 5 0.200 1.1500 3º10´ IR5ACME

1-3/8 4 0.250 1.2500 3º39´ IR4ACME

1-1/2 4 0.250 1.3750 3º19´ IR4ACME

1-3/4 4 0.250 1.6250 2º48´ IR4ACME

2 4 0.250 1.8750 2º26´ IR4ACME

Because this thread standard is characterized with large pitch and small diameter, (that is a large lead angle) the standard inserts and toolholders can not
be used for machining this thread type. The application is limited to outside of the standard.
Note : The above tables show correspondence of internal toolholders at the time of setting clearance between thread and toolholder to 3 mm (1 mm in case of
SN type) and the finishing stock to 0.1 mm.

Tungaloy B451
 Standard Cutting Conditions and Infeed Methods

Threading guidelines
Determine the infeed per pass and number of threads
whilst referring to the table and description below.
Pitch (mm) 0.5 0.75 1 1.25 1.5 1.75 2 2.5 3 3.5 4 4.5 5~
TPI 48 32 24 20 16 14 12 10 8 7 6 5.5 5~
No. of passes 4~6 4~7 4~8 5~9 6 ~ 10 7 ~ 12 7 ~ 12 8 ~ 14 10 ~ 16 11 ~ 18 11 ~ 18 11 ~ 19 12 ~ 24
Note:
• When using the full-profile insert, set the total infeed amount by zero cutting of work hardened surfaces will reduce tool life.)
taking the finish stock of 0.1mm into account. • The partial-profile insert or inside diameter insert has small nose
• Set the first infeed to 150 ~ 200% of nose R and do not allow it R. Reduce the infeed per pass and increase the no. of passes.
to exceed 0.5 mm (0.020"). • Regarding standard infeed per passes and no. of passes, please
• The infeed amount during the final pass must be a minimum of refer to our catalogue.
0.05 mm. No zero cuts should be made. (Extra small infeed or

Infeed methods for threading tools

Infeed method Features

• Most simple and usual method

Suitable for relatively small pitch threads of easily machinable material.
• Chip contact length on right and left is longer, causing chattering, with increased load
on the nose end.
• When the half included angle is not symmetrical to the right and left, infeeding in the
direction of 1/2 of the included angle will ensure equal machining with right and left
Straight infeed (radial infeed) cutting edges.

• Suitable for large pitch threads or easy to tear materials. Effectively prevents chattering.
Threading Tool

• Chips are discharged in one direction only. Satisfactory chip control.

• Edge on the right (with zero infeed) tends to be worn heavily.

Single edge infeed

(flank infeed)
• Suitable for large pitch threads or easy to tear materials. Effectively prevents chattering.

• Chips are discharged in one direction only. Satisfactory chip control.

• Edge on the right performs some cutting, therefore

wear of this edge can thus be suppressed.
Modified single-edge infeed
(flank infeed)
• Suitable for large pitch threads or easy to tear material. Effectively prevents chattering.

• Chips are discharged alternately in right and left directions, resulting possibly in
entanglement.

• Right and left edges are used alternately, ensuring uniform wear and extending tool life.
Alternating flank infeed

B452 www.tungaloyamerica.com
 I nf eed per Pas s and Numb er o f Pa sse s
ISO metric full-profile inserts (for external) ISO metric full-profile inserts (for internal)
Pitch 0.5 0.75 1 1.25 1.5 1.75 2 2.5 3 3.5 4 4.5 5 5.5 6 Pitch 0.5 0.75 1 1.25 1.5 1.75 2 2.5 3 3.5 4 4.5 5 5.5 6
Height of 0.32 0.47 0.63 0.79 0.95 1.11 1.27 1.58 1.9 2.21 2.53 2.85 3.16 3.48 3.8 Height of 0.29 0.43 0.58 0.72 0.87 1.01 1.16 1.45 1.74 2.03 2.32 2.61 2.9 3.19 3.48
thread thread
Total depth 0.42 0.57 0.73 0.89 1.05 1.21 1.37 1.68 2 2.31 2.63 2.95 3.26 3.58 3.9 Total depth 0.39 0.53 0.68 0.82 0.97 1.11 1.26 1.55 1.84 2.13 2.42 2.71 3 3.29 3.58
of cut of cut
1 0.15 0.18 0.25 0.25 0.3 0.3 0.3 0.3 0.35 0.35 0.4 0.4 0.45 0.5 0.5 1 0.08 0.1 0.14 0.15 0.2 0.2 0.2 0.25 0.25 0.3 0.3 0.35 0.35 0.4 0.4
2 0.12 0.12 0.2 0.2 0.25 0.25 0.25 0.25 0.3 0.3 0.35 0.35 0.35 0.35 0.4 2 0.07 0.09 0.13 0.13 0.16 0.18 0.18 0.22 0.22 0.25 0.25 0.25 0.25 0.25 0.25
3 0.1 0.12 0.13 0.15 0.2 0.2 0.2 0.25 0.25 0.3 0.3 0.3 0.3 0.3 0.3 3 0.07 0.08 0.11 0.12 0.14 0.16 0.17 0.2 0.2 0.22 0.22 0.22 0.22 0.22 0.22
4 0.05 0.1 0.1 0.14 0.15 0.16 0.2 0.23 0.2 0.25 0.25 0.25 0.25 0.25 0.25 4 0.06 0.08 0.1 0.11 0.12 0.14 0.16 0.18 0.18 0.2 0.2 0.2 0.2 0.2 0.2
5 0.05 0.05 0.1 0.1 0.15 0.15 0.2 0.2 0.21 0.2 0.2 0.25 0.23 0.25 5 0.06 0.07 0.08 0.1 0.12 0.12 0.14 0.16 0.16 0.18 0.18 0.18 0.2 0.2 0.19
6 0.05 0.05 0.1 0.12 0.15 0.15 0.2 0.2 0.2 0.2 0.2 0.2 6 0.05 0.06 0.07 0.09 0.1 0.1 0.12 0.15 0.15 0.16 0.18 0.18 0.18 0.18 0.18
7 0.05 0.1 0.15 0.15 0.15 0.15 0.2 0.2 0.2 0.2 7 0.05 0.05 0.07 0.08 0.09 0.1 0.1 0.14 0.14 0.16 0.16 0.16 0.16 0.17

8 0.05 0.1 0.15 0.15 0.15 0.15 0.18 0.15 0.15 8 0.05 0.05 0.07 0.08 0.1 0.13 0.13 0.14 0.14 0.14 0.14 0.16

9 0.05 0.1 0.15 0.15 0.15 0.15 0.15 0.15 9 0.05 0.06 0.08 0.12 0.12 0.14 0.14 0.14 0.14 0.15

10 0.1 0.1 0.13 0.15 0.15 0.15 0.15 10 0.05 0.06 0.1 0.11 0.12 0.12 0.13 0.13 0.14
Number of passes

Number of passes
11 0.05 0.1 0.1 0.15 0.13 0.15 0.15 11 0.05 0.08 0.1 0.12 0.12 0.13 0.13 0.14

12 0.05 0.1 0.1 0.1 0.15 0.15 12 0.06 0.1 0.1 0.12 0.12 0.13 0.13

13 0.1 0.1 0.1 0.15 0.15 13 0.05 0.07 0.1 0.11 0.12 0.12 0.13

14 0.05 0.1 0.1 0.1 0.15 14 0.05 0.09 0.1 0.12 0.12 0.13

15 0.1 0.1 0.1 0.1 15 0.07 0.1 0.11 0.12 0.12

16 0.05 0.1 0.1 0.1 16 0.05 0.09 0.1 0.12 0.12

17 0.1 0.1 0.1 17 0.08 0.1 0.1 0.12

18 0.05 0.1 0.1 18 0.05 0.1 0.1 0.1

19 0.1 0.1 19 0.08 0.1 0.1

20 0.05 0.1 20 0.05 0.1 0.1

21 0.1 21 0.08 0.1

22 0.05 22 0.05 0.1

23 23 0.08

Threading Tool
24 24 0.05

(Unit: mm) (Unit: mm)

Unified full-profile inserts Whitworth full-profile inserts

For external For internal For external For internal

TPI 24 20 18 16 14 12 8 24 20 18 16 14 12 8 TPI 20 19 18 16 14 12 11 10 8 20 19 18 16 14 12 11 10 8

Height of 0.67 0.8 0.89 1.01 1.15 1.34 2.01 0.61 0.74 0.82 0.92 1.05 1.23 1.84 Height of 0.83 0.88 0.92 1.04 1.19 1.39 1.51 1.66 2.08 0.83 0.88 0.92 1.04 1.19 1.39 1.51 1.66 2.08
thread thread
Total depth of 0.77 0.9 0.99 1.11 1.25 1.44 2.11 0.71 0.84 0.92 1.02 1.15 1.33 1.94 Total depth 0.93 0.98 1.02 1.14 1.29 1.49 1.61 1.76 2.18 0.93 0.98 1.02 1.14 1.29 1.49 1.61 1.76 2.18
cut of cut

1 0.25 0.25 0.28 0.3 0.3 0.3 0.35 0.2 0.2 0.2 0.2 0.25 0.25 0.3 1 0.25 0.28 0.3 0.3 0.3 0.3 0.3 0.35 0.35 0.2 0.2 0.22 0.22 0.25 0.25 0.25 0.3 0.35

2 0.22 0.2 0.23 0.25 0.25 0.25 0.3 0.16 0.16 0.18 0.18 0.2 0.2 0.25 2 0.2 0.22 0.24 0.25 0.25 0.25 0.25 0.3 0.3 0.18 0.18 0.18 0.18 0.21 0.21 0.21 0.25 0.3

3 0.18 0.18 0.18 0.18 0.23 0.2 0.2 0.23 0.25 0.16 0.16 0.17 0.17 0.2 0.2 0.2 0.22 0.25
3 0.15 0.16 0.18 0.18 0.23 0.21 0.25 0.12 0.13 0.15 0.16 0.18 0.18 0.22
4 0.15 0.15 0.15 0.14 0.2 0.18 0.18 0.2 0.23 0.14 0.16 0.16 0.16 0.18 0.18 0.18 0.2 0.22
4 0.1 0.14 0.15 0.15 0.18 0.18 0.22 0.1 0.12 0.14 0.14 0.16 0.16 0.2
5 0.1 0.1 0.1 0.12 0.16 0.15 0.15 0.15 0.22 0.12 0.13 0.14 0.14 0.16 0.16 0.16 0.16 0.2
5 0.05 0.1 0.1 0.1 0.14 0.15 0.2 0.08 0.1 0.1 0.11 0.13 0.13 0.18
6 0.05 0.05 0.05 0.1 0.1 0.14 0.14 0.14 0.2 0.08 0.1 0.1 0.12 0.14 0.14 0.14 0.14 0.18
Number of passes

Number of passes

6 0.05 0.05 0.08 0.1 0.12 0.2 0.05 0.08 0.1 0.1 0.1 0.1 0.16
7 0.05 0.05 0.12 0.12 0.12 0.18 0.05 0.05 0.05 0.1 0.1 0.1 0.12 0.12 0.16
7 0.05 0.05 0.1 0.16 0.05 0.05 0.08 0.08 0.1 0.14
8 0.1 0.12 0.12 0.16 0.05 0.05 0.1 0.1 0.12 0.14
8 0.08 0.16 0.05 0.05 0.08 0.12
9 0.05 0.1 0.1 0.14 0.1 0.1 0.1 0.12
9 0.05 0.12 0.08 0.12
10 0.05 0.05 0.1 0.05 0.1 0.1 0.11

10 0.1 0.05 0.1

11 0.05 0.05 0.05 0.1

11 0.05 0.1
12 0.05

12 0.05
13

13 14

14 15

(Unit: mm) (Unit: mm)

Tungaloy B453
 I nf eed per Pas s and Numb er o f Pa sse s

30˚ Trapezoidal (TR) inserts 29˚ Trapezoidal (TR) inserts

For external For internal For external For internal

Pitch 2 3 4 5 6 2 3 4 5 6 TPI 8 6 5 8 6 5

Height of 1.25 1.75 2.25 2.75 3.5 1.25 1.75 2.25 2.75 3.5 Height of 1.88 2.41 2.92 1.88 2.41 2.92
thread thread
Total depth 1.35 1.85 2.35 2.85 3.6 1.35 1.85 2.35 2.85 3.6 Total depth 1.98 2.51 3.02 1.98 2.51 3.02
of cut of cut
1 0.25 0.25 0.3 0.3 0.3 0.2 0.22 0.25 0.25 0.25 1 0.25 0.25 0.25 0.22 0.22 0.22
2 0.2 0.22 0.25 0.25 0.25 0.18 0.2 0.22 0.22 0.22 2 0.22 0.22 0.22 0.2 0.2 0.2
3 0.2 0.2 0.22 0.2 0.23 0.18 0.18 0.2 0.2 0.21 3 0.2 0.2 0.2 0.18 0.18 0.18
4 0.18 0.18 0.2 0.2 0.2 0.16 0.16 0.2 0.18 0.2 4 0.18 0.18 0.18 0.16 0.18 0.18
5 0.15 0.17 0.18 0.18 0.18 0.15 0.16 0.17 0.18 0.18 5 0.16 0.17 0.18 0.16 0.16 0.16
6 0.12 0.16 0.16 0.16 0.18 0.13 0.16 0.16 0.16 0.18 6 0.16 0.16 0.16 0.16 0.15 0.16
7 0.1 0.14 0.15 0.16 0.16 0.1 0.14 0.16 0.16 0.16 7 0.16 0.16 0.16 0.15 0.15 0.15
8 0.1 0.14 0.14 0.15 0.16 0.1 0.14 0.14 0.15 0.16 8 0.14 0.14 0.14 0.14 0.14 0.14
9 0.05 0.12 0.14 0.14 0.16 0.1 0.12 0.14 0.14 0.16 9 0.14 0.14 0.14 0.14 0.14 0.14
10 0.12 0.12 0.14 0.16 0.05 0.12 0.12 0.14 0.16 10 0.12 0.14 0.14 0.12 0.14 0.14
Number of passes

Number of passes
11 0.1 0.12 0.14 0.16 0.1 0.12 0.14 0.16 11 0.1 0.14 0.14 0.1 0.14 0.14
12 0.05 0.12 0.12 0.15 0.1 0.12 0.12 0.15 12 0.1 0.12 0.14 0.1 0.12 0.14
13 0.1 0.12 0.15 0.05 0.1 0.12 0.15 13 0.05 0.12 0.12 0.1 0.12 0.12
14 0.1 0.12 0.15 0.1 0.12 0.15 14 0.12 0.12 0.05 0.12 0.12
15 0.05 0.12 0.14 0.1 0.12 0.14 15 0.1 0.12 0.1 0.12
16 0.1 0.14 0.05 0.1 0.14 16 0.1 0.12 0.1 0.12
17 0.1 0.12 0.1 0.12 17 0.05 0.12 0.1 0.12
18 0.1 0.12 0.1 0.12 18 0.12 0.05 0.12
19 0.05 0.12 0.1 0.12 19 0.1 0.1
20 0.12 0.05 0.12 20 0.1 0.1
21 0.1 0.1 21 0.05 0.1
22 0.1 0.1 22 0.05
23 0.05 0.1 23
24 0.05 24
Threading Tool

25 25
26 26
(Unit: mm) (Unit: mm)
PT full-profile inserts NPT full-profile inserts
For external For internal For external For internal

TPI 28 19 14 11 19 14 11 TPI 18 14 11.5 8 14 11.5 8

Height of 0.6 0.86 1.16 1.48 0.86 1.16 1.48 Height of 1.14 1.47 1.79 2.58 1.47 1.79 2.58
thread thread
Total depth 0.7 0.96 1.26 1.58 0.96 1.26 1.58 Total depth 1.24 1.57 1.89 2.68 1.57 1.89 2.68
of cut of cut
1 0.25 0.28 0.3 0.3 0.22 0.25 0.25 1 0.2 0.25 0.25 0.3 0.22 0.22 0.25
2 0.2 0.2 0.25 0.25 0.2 0.22 0.22 2 0.18 0.22 0.22 0.25 0.2 0.2 0.2
3 0.1 0.18 0.2 0.22 0.18 0.18 0.18 3 0.17 0.2 0.2 0.2 0.18 0.18 0.2
4 0.1 0.15 0.15 0.18 0.16 0.14 0.18 4 0.16 0.18 0.18 0.2 0.18 0.18 0.2
5 0.05 0.1 0.11 0.15 0.1 0.12 0.15 5 0.14 0.17 0.18 0.2 0.16 0.16 0.2
6 0.05 0.1 0.12 0.05 0.1 0.13 6 0.12 0.16 0.17 0.2 0.14 0.16 0.2
7 0.1 0.11 0.05 0.1 0.12 7 0.12 0.12 0.16 0.18 0.12 0.16 0.18
8 0.05 0.1 0.1 0.1 8 0.1 0.12 0.14 0.18 0.12 0.14 0.18
9 0.1 0.05 0.1 9 0.05 0.1 0.12 0.16 0.1 0.12 0.16
10 0.05 0.1 10 0.05 0.12 0.16 0.1 0.12 0.16
Number of passes

Number of passes

11 0.05 11 0.1 0.14 0.05 0.1 0.14

12 12 0.05 0.14 0.1 0.14
13 13 0.12 0.05 0.12
14 14 0.1 0.1
15 15 0.1 0.1
16 16 0.05 0.1
17 17 0.05
18 18
19 19
20 20
21 21
22 22
23 23
24 24
25 25
26 26
(Unit: mm) (Unit: mm)
B454 www.tungaloyamerica.com
 Designation System for TAC Threading Tools (TT-type)

Insert

TT 1
R 2
42 3
M -005
4

1 Hand 2 Insert size (mm) 3 Thread type 4 Corner radius (mm)

R Right Inscribed circle 12.7 M 60˚ thread angle Blank 0
L Left Thickness 3.2 W 55˚ thread angle -005 0.05
Toolholder

TT- 1
20 2
20 3
R 4
E
1 Shank height (mm) 2 Shank width (mm) 3 Hand 4 External or Internal

R Right E External
L Left I Internal

TT-type Insert
60° thre ad angle
s
5°

60°
ød

Threading Tool
θ° 60°
Right hand (R) shown

Partial-profile insert for external and internal threads

Grade
Pitch Hand ød s Applicable
TPI of Designation Cermet Uncoated θ°
(mm) cut (mm) (mm) toolholders
NS9530 TH10
≤3 ≥8 R TTR42M-005 䖃 䖃 12.7 3.2 60 TT-****RE/LI

≤3 ≥8 L TTL42M-005 䖃 䖃 12.7 3.2 60 TT-****LE/RI

TT-type Insert
55° thre ad angle
s
5°

55°
ød

θ° 60°
Right hand (R) shown.

Partial-profile insert for external and internal threads

Grade
Pitch Hand ød s
TPI of Designation Cermet Uncoated θ° Applicable
(mm) cut (mm) (mm) toolholders
NS9530 TH10
≤3 ≥8 R TTR42W-005 䖃 䖃 12.7 3.2 55 TT-****RE/LI

≤3 ≥8 L TTL42W-005 䖃 䖃 12.7 3.2 55 TT-****LE/RI

䖃 : Line up / Packing Quantity = 5 pcs.

Tungaloy B455
 TT-R /LE
"T T t y p e "E x ter nal t hread i ng to o l ho l d er s, pi n l oc k

L2 L1
45°

f1

b
f
h1

h
Right hand (R) shown.

Metric h b L1 L2 h1 f f1 Insert
TT-2525R/LE 25 25 150 25 25 32  15 TTR/L42...

SPARE PARTS
Designation Clamp Right-left screw Wrench
TT-2525R/LE CP91 DS-6 P-3

TT-R I
"T T t y p e "I n te r nal t hread i ng to o l ho l d er s, p i n l oc k

Min. bore dia : ø50

最小加工径 L1
L2
5°

b
f
90°
3.2
h1

h
Right hand (R) shown.
Threading Tool

Metric øDm h b L1 L2 h1 f Insert

TT-2525RI 50 25 25 200 70 25 35 TTL42...
Notes : The left hand insert is used for right hand toolholders.

SPARE PARTS
Designation Clamp Right-left screw Wrench
TT-2525RI CP91 DS-6 P-3

P 1 1.25 1.5 1.75 2 2.5 3

• Relationship between pitch, depth
of cut and number of passes for H2 0.6 0.76 0.92 1.09 1.25 1.57 1.9
external metric threading H 0.866 1.083 1.299 1.516 1.732 2.165 2.598
H/4

1 0.25 0.3 0.3 0.3 0.35 0.4 0.4

R 0.1083P
2 0.15 0.2 0.25 0.25 0.25 0.3 0.35
H2

3 0.1 0.1 0.15 0.2 0.2 0.25 0.28

H

P
Number of passes

4 0.05 0.06 0.1 0.1 0.16 0.2 0.2

5 0.05 0.06 0.05 0.1 0.1 0.15 0.2
H/8

Pitch 1 ~ 3 mm
6 0.06 0.05 0.07 0.07 0.1 0.13
Note: Maximum machinable pitch is 3 mm. 7 0.02 0.05 0.05 0.07 0.1
8 0.02 0.02 0.05 0.1
 Part assembly 9 0.02 0.03 0.05
Insert 10 0.02 0.05
11 0.02
Clamp 12 0.02
(Unit: mm)
Right-left
screw

Reference pages
TT-R/LE, TT-RI: Inserts → B455

B456 www.tungaloyamerica.com
STC R /L-18
Prec i s i o n t h re a d i ng to o l s w i t h uni q uel y shap e d i n s e r t f or s w i s s t y p e m a c h i n e , a u tom a t i c a n d ge n e ral lathes

L1
L2

h1

h
h2

b
f
Right hand (R) shown.

Inch h b L1 L2 h1 f h2 Insert
STCR/L06-18 0.375 0.375 4.75 0.73 0.375 0.375 0.177 TC*18...

STCR/L08-18 0.500 0.500 4.75 0.73 0.500 0.500 0.098 TC*18...

STCR/L10-18 0.625 0.625 4.75 0.73 0.625 0.625 - TC*18...

STCR/L12-18 0.750 0.750 4.750 0.900 0.750 1.000 - TC*18...

STCR/L16-18 1.000 1.000 5.500 0.900 1.000 1.250 - TC*18...

Metric h b L1 L2 h1 f h2 Insert
STCR/L1010X18 10 10 120 18.5 10 10 4.5 TC*18...

STCR/L1212F18 12 12 85 18.5 12 12 2.5 TC*18...

STCR/L1212X18 12 12 120 18.5 12 12 2.5 TC*18...

STCR/L1616X18 16 16 120 18.5 16 16 - TC*18...

STCR/L2020H18 20 20 100 18.5 20 20 - TC*18...

STCR/L2020X18 20 20 120 23 20 25 - TC*18...

STCR/L2525Z18 25 25 135 23 25 30 - TC*18...

Threading Tool
- The right hand insert (TCT18R...) is used for the right hand toolholders (STCR...),
and the left hand insert (TCL18...) is used for the left hand toolholders (STCL...).

SPARE PARTS
Designation Clamping screw Wrench
STCR... CSTC-4L100DL T-1008/5
STCL... CSTC-4L100DR T-1008/5

Reference pages
STCR/L-18: Inserts, Standard cutting conditions → B459

Tungaloy B457
 JS-STC L18
Pre c i s i o n t h read i ng to o l s w i t h uni q uel y sh a p e d i n s e r t f or s w i s s t y p e m a c h i n e , a u tom a t i c a n d ge n eral lathes

L1

s
øD
L2

h
B
94°

Left hand (L) shown.

Metric øDs L1 L2 h B f Insert

JS14H-STCL18 14 100 20 13 14 6 TC*18R...

JS159F-STCL18 15.875 (0.625") 85 20 15 14 6 TC*18R...

JS16F-STCL18 16 85 20 15 14 6 TC*18R...

JS19G-STCL18 19.05 (0.750") 90 20 18 14 6 TC*18R...

JS19X-STCL18 19.05 (0.750") 120 20 18 14 6 TC*18R...

JS20G-STCL18 20 90 20 19 14 6 TC*18R...

JS20X-STCL18 20 120 20 19 14 6 TC*18R...

JS22X-STCL18 22 120 20 21 12.25 10 TC*18R...

JS25H-STCL18 25 100 20 24 12.25 10 TC*18R...

JS254X-STCL18 25.4 (1.000") 120 20 24 12.25 10 TC*18R...

- The right hand insert (TCT18R...) is used for the left hand toolholders (STCL...)

SPARE PARTS
Designation Clamping screw Wrench
Threading Tool

JS**STCL18 CSTC-4L100DL T-1008/5

Reference pages
JS-STCL18: Inserts, Standard cutting conditions → B459

B458 www.tungaloyamerica.com
 INSERT
TCT18R /L ( For T hread i ng )
T

S
rε f
ød
θ˚
Coated
AH725 Pitch min Pitch max f S rε T ød
Designation (mm) (mm) θº
R L (in) (in) (in) (in) (in)
TCT18R/L-60N-010 䖃 䖃 0.8 3 0.063 0.105 0.004 60 0.157 0.709
TCT18R/L-60N-020 䖃 䖃 1.5 3 0.063 0.101 0.008 60 0.157 0.709
䖃㻌: Line up

STA N DA R D CUT T ING CONDIT IONS

Workpiece material Grade Cutting speed Pitch (in) TPI
ISO Vc (sfm)
Low carbon steels AH725 197 - 492 0.031 - 0.118 32 - 8
S15C, S20C, etc. C15, C20, etc.
Carbon steels, Alloy steels AH725 197 - 492 0.031 - 0.118 32 - 8
S55C, SCM440, etc. C55, 42CrMoS4, etc.
Prehardened steels AH725 197 - 492 0.031 - 0.118 32 - 8
NAK80, PX5, etc.
Stainless steels
SUS303, SUS316,etc. X5CrNi18-9, X5CrNiMo17-12-2, etc
AH725 164 - 262 0.031 - 0.118 32 - 8

Gray cast irons

250, 300, etc. AH725 164 - 328 0.031 - 0.118 32 - 8

Ductile cast irons

Threading Tool
400-15, 600-3, etc. AH725 164 - 328 0.031 - 0.118 32 - 8

Titanium alloys
Ti-6AI-4V, etc. AH725 98 - 328 0.031 - 0.118 32 - 8

Superalloys
Inconel718, etc. AH725 98 - 328 0.031 - 0.118 32 - 8

Tungaloy B459
 JSTTR /L
E x te r n a l t h re ad i ng to o l ho l d er s f o r sm al l l a t h e

L1

b
f
L2
5˚

h1

h
h2
Right hand (R) shown.

Inch h b L1 L2 h1 f h2 Insert
JSTTR/L063 0.375 0.375 5 0.6875 0.375 0.375 0.100 JTTR/L30...
JSTTR/L083 0.500 0.500 5 0.6875 0.500 0.500 - JTTR/L30...
JSTTR/L103 0.625 0.625 5 0.6875 0.625 0.625 - JTTR/L30...

Metric h b L1 L2 h1 f h2 Insert
JSTTR/L1010X3 10 10 120 18.5 10 9.5 2 JTTR/L30...
JSTTR/L1212F3 12 12 85 18.5 12 11.5 - JTTR/L30...
JSTTR/L1212X3 12 12 120 18.5 12 11.5 - JTTR/L30...
JSTTR/L1616X3 16 16 120 16.5 16 15.5 - JTTR/L30...
Recommend clamping torque: 0.89 lbt ft (1.2 N m)

SPARE PARTS
Designation Clamping screw Wrench
JSTTR/L... CSTB-4SD T-8F
Threading Tool

JS-TTL3
E x te r n a l t h re ad i ng to o l ho l d er s f o r sm al l l a t h e

L1

øDs
90°
f

h
B

h
Left hand (L) shown.

Metric øDs f L1 h B Insert

JS19K-TTL3 19.05 10 125 18 11.5 JTTR30...
JS20K-TTL3 20 10 125 19 11.5 JTTR30...
JS22K-TTL3 22 10 125 21 11.5 JTTR30...
JS25K-TTL3 25.4 10 125 24 12.7 JTTR30...

Recommend clamping torque: 2.58 lbt ft (3.5 N m)

SPARE PARTS
Designation Clamping screw Wrench
JS**-TTL3 CSTB-4S T-15F

Reference pages
JSTTR/L, JS-TTL3: Inserts → B461

B460 www.tungaloyamerica.com
 INSERT
J T T ( s h a r p e d g e)
θ
rε

s
ød T Right hand (R) shown.

Coated Cermet Uncoated

rε ød T s
Designation SH725 J740 NS9530 TH10 θ°
(in) (in) (in) (in)
R L R L R L R L
JTTR/L3005F-55 0.002 䖃 䖃 55 0.375 0.125 0.024

JTTR/L3005F 0.002 䖃 䖃 䖃 䖃 䖃 60 0.375 0.125 0.035

JTTR/L3010F 0.004 䖃 䖃 䖃 䖃 䖃 60 0.375 0.125 0.035

Machinable pitch range: 0.020" to 0.039". 䖃 : Line up

Threading Tool

Tungaloy B461
 JSXB R /L
E x te r n a l t h re a d i ng to o l ho l d er s

R3

b
L1
L2
40°
C-type

h1

h
Right hand (R) shown.

Metric h b L1 L2 R3 h1 f Insert
JSXBR1010K8-C 10 10 125 29 6.4 10 5.7 JXT*R...
JSXBR1212K8-C 12 12 125 29 6.4 12 7.7 JXT*R...
JSXBR1616K8 16 16 125 29 6.4 16 11.7 JXT*R...
JSXBR2020K8 20 20 125 29 6.4 20 15.7 JXT*R...
JSXBR2525K8 25 25 125 29 6.4 25 20.7 JXT*R...

• Can be wrenched from back side with both end torx screw.
• This toolholder is also compatible with JSXB-type insert for back turning.

SPARE PARTS
Designation Clamping screw Wrench Wrench (Optional parts)
JSXBR... CSTB-4SD T-8F (T-8L)

INSERT
J X T ( s h a r p ed g e)
Threading Tool

60° 60°
60°
0.6 rε 0.6
rε rε

ød T T T
1-Type 2-Type 3-Type
JXT1R JXT2R JXT3R

rε Coated Uncoated ød T
Designation θ°
(mm) J740 TH10 (mm) (mm)
JXT1R6000F 0.03 䖃 䖃 60 8 3.97

JXT2R6000F 0.03 䖃 䖃 60 8 3.97

Machinable pitch range: 0.5 to 1 mm 䖃 : Line up

B462 www.tungaloyamerica.com
MT VN R /L-5
" Tu n g T h re a d " E x te r n a l t h re a d i n g to o l h o l d e r s f o r l a y d o w n i n s e r t s

L1
L2

b
f
7°

h
Right hand (R) shown.

Metric b h L1 L2 f Insert
MTVNR-2525M5 25 25 152 39 31.8 L53 5B**EXT-FC
MTVNR-3232M5 32 32 178 39 38.1 L53 5B**EXT-FC

SPARE PARTS
Designation Shim Lock pin Clamp Clamping screw Wrench
MTVNR... LS53NOFORMEXT NL-58 TC-250 STC-11 1/8HEX

Threading Tool

Reference pages
MTVNR/L-5: Inserts → B464

Tungaloy B463
 H S-LN FR /L-53
E xc h a n g e a b l e i n te r n a l t h re a d i n g h e a d s f o r l a y d o w n i n s e r t s

øD

s2
s1

øD
øDm

f
L2
L1
Right hand (R) shown.

Metric øDm øDs1 f L1 Insert

HS40-LNFR-53 50 40 28.7 41.3 L53 5B**INT-FC
HS50-LNFR-53 63 50 32.7 41.3 L53 5B**INT-FC

SPARE PARTS
Designation Lock pin Clamp Clamping screw Wrench
HS**-LNFR-53 NL-56 TC-250 STC-11 1/8HEX

Shank
Designation øDs2 (in) L2 (in)
S-570-40M-40 1.575 10.75
S-570-50M-50 1.969 14.41

SPARE PARTS
Designation Clamping screw Wrench
S-570-40M-40 SS100 5/32HEX
S-570-50M-50 SS94 1/4EX
Threading Tool

Full-profile insert (Single-sided)

ød
T

Taper External insert (mm) Internal insert (mm)

Grade Grade
Connection TPI
mm/mm TPF Designation Coated ød T Designation Coated ød T
AH725 AH725

API 5 1/16 0.75 L53 5B75 EXT-FC 䖃 15.875 4.8 L53 5B75 INT-FC 䖃 15.875 4.8
Buttress 5 1/12 1 L53 5B1 EXT-FC 䖃 15.875 4.8 L53 5B1 INT-FC 䖃 15.875 4.8

䖃 : Line up

B464 www.tungaloyamerica.com
MT VN R /L-54
E x te r n a l t h re a d i n g to o l h o l d e r f o r l a y d o w n d o u b l e - s i d e i n s e r t s

L1
L2

b
f
7°

h
Right hand (R) shown.

Metric h b L1 L2 f Insert
MTVNR-3232M54 32 32 178 39 38.1 LDS 54**FT-CB#...

SPARE PARTS
Designation Shim Lock pin Clamp Clamping screw Wrench
MTVNR-3232M54 LS53NOFORMEXT NL-58 TC-250 STC-11 1/8HEX

Threading Tool

Reference pages
MTVNR/L-54: Inserts → B466

Tungaloy B465
 H S -LN FR /L- 54A P I
E xc h a n g e a b l e i n te r n a l t h re a d i n g h e a d s f o r l a y d o w n d o u b l e - s i d e i n s e r t s

øD

2s
s1

øD
øDm

f
L2
L1
Right hand (R) shown.

Inch øDm øDs1 f L1 Insert

HS40-LNFR-54API 1.970 1.57 1.063 1.26 LDS 54**FT-CB#...
HS50-LNFR-54API 2.480 1.97 1.378 1.57 LDS 54**FT-CB#...

SPARE PARTS
Designation Lock pin Clamp Clamping screw Wrench
HS40-LNFR-54API H410-1 TC-250 STC-11 1/8HEX
HS50-LNFR-54API NL-56 TC-250 STC-11 1/8HEX

Shank
Designation øDs2 (in) L2 (in)
S-570-40M-40 1.575 10.75
S-570-50M-50 1.969 14.41

SPARE PARTS
Designation Clamping screw Wrench
S-570-40M-40 SS100 5/32HEX
Threading Tool

S-570-50M-50 SS94 1/4EX

Full-profile insert (Double-sided)

rε

ød
T

Taper Grade
Connection TPI
Thread
Designation
ød T rε
form Coated
mm/mm TPF (in) (in) (in)
AH725
5 V-0.040 1/4 3 LDS 54 530 FT-CB #5 䖃 0.625 0.252 0.020

4 V-0.038R 1/6 2 LDS 54 428 FT-CB #1 䖃 0.625 0.252 0.038

API Rotary
shoulder 4 V-0.038R 1/4 3 LDS 54 438 FT-CB #2 䖃 0.625 0.252 0.038
connection
4 V-0.050 1/6 2 LDS 54 425 FT-CB #3 䖃 0.625 0.252 0.025

4 V-0.050 1/4 3 LDS 54 435 FT-CB #4 䖃 0.625 0.252 0.025

䖃 : Line up

B466 www.tungaloyamerica.com
MT VOR
E x te r n a l m u l t i - c l a m p to o l h o l d e r s f o r o n e d g e i n s e r t s

b
f
L2
L1

h
Right hand (R) shown.

Metric h b L1 L2 f D Insert
MTVOR-2525M4 25 25 152 31 31.7 5.8 TNM*43...
MTVOR-3232M4 32 32 178 31 38.1 5.8 TNM*43...
MTVOR-2525M5 25 25 152 36 31.7 7.3 TNM*54...
MTVOR-3232M5 32 32 178 36 38.1 7.3 TNM*54...
Note: For TNMC inserts, STVOR/L toolholder is recommended. Also, M-Type toolholder is available.
.

SPARE PARTS
Designation Lock pin Clamp Clamping screw Wrench
MTVOR-**M4 NL-44 TC-190 STC-5 3/32HEX
MTVOR-**M5 NL-56 TC-250 STC-11 1/8HEX

Threading Tool

Reference pages
MTVOR: Inserts → B469

Tungaloy B467
 ST VO R
E x te r n a l s c re w - o n to o l h o l d e r s f o r o n e d g e i n s e r t s

b
f
L2
L1

h
Right hand (R) shown.

Inch h b L1 L2 f D Insert
STVOR-2525M4 0.984 0.984 5.91 1.23 1.25 0.23 TNMC43...
STVOR-3232M4 1.260 1.260 7.01 1.23 1.50 0.23 TNMC43...
STVOR-2525M5 0.984 0.984 5.91 1.42 1.25 0.29 TNMC54...
STVOR-3232M5 1.260 1.260 7.00 1.42 1.50 0.29 TNMC54...

SPARE PARTS
Designation Clamping screw Clamp (Optional parts) Clamping screw (Optional parts) Wrench
STVOR-**M4 SD2 (TC-190) (STC-9) T20TORX 3/32HEX
STVOR-**M5 SD3 (TC-250) (STC-11) T20TORX 1/8HEX

H S -M TH OR
E xc h a n g e a b l e i nter nal t hread i ng head s, f o r on e d ge i n s e r t , a p p l i c a b l e on S - 570 s h a n ks
Threading Tool

s2
øD
øDs1

L2
f

0˚ L1
Right hand (R) shown.

Inch øDm øDs1 f L1 Insert

HS40-MTHOR-4 2.625 1.57 1.203 1.26 TNM*43...
HS50-MTHOR-4 2.875 1.97 1.413 1.57 TNM*43...
HS40-MTHOR-5 3.200 1.57 1.203 1.26 TNM*54...
HS50-MTHOR-5 3.250 1.97 1.413 1.57 TNM*54...

SPARE PARTS
Designation Lock pin Clamp Clamping screw Wrench
HS**-MTHOR-4 NL-44 TC-190 STC-5 3/32HEX
HS**-MTHOR-5 NL-56 TC-250 STC-11 1/8HEX

Shank
Designation øDs2 (in) L2 (in)
S-570-40M-40 1.575 10.75
S-570-50M-50 1.969 14.41

SPARE PARTS
Designation Clamping screw Wrench
S-570-40M-40 SS100 5/32HEX
S-570-50M-50 SS94 1/4EX

Reference pages
STVOR, HS-MTHOR: Inserts → B469

B468 www.tungaloyamerica.com
Full profile insert and partial topping insert
T T

ød ød
TNMA TNMC

Taper External insert (in) Internal insert (in)

Grade Grade
Connection TPI
mm/mm TPF Designation Coated ød T Designation Coated ød T
AH725 AH725
API 10 1/16 0.75 TNMA 43 10RD EXT 䖃 0.5 0.189 TNMA 43 10RD INT 䖃 0.5 0.189
Round 8 1/16 0.75 TNMA 43 8RD EXT 䖃 0.5 0.189 TNMA 43 8RD INT 䖃 0.5 0.189
API 5 1/12 1 TNMA 54 5B1 EXT-FC 䖃 0.625 0.252 TNMA 54 5B1 INT-FC 䖃 0.625 0.252
Buttress 5 1/16 0.75 TNMA 54 5B75 EXT-FC 䖃 0.625 0.252 TNMA 54 5B75 INT-FC 䖃 0.625 0.252
16 - - TNMA43NT16PEXT-PT 䖃 0.5 0.189 - - - -
14 - - TNMA43NT14PEXT-PT 䖃 0.5 0.189 - - - -
12 - - TNMA43NT12PEXT-PT 䖃 0.5 0.189 - - - -
10 - - TNMA43NT10PEXT-PT 䖃 0.5 0.189 - - - -
ACME
(29º 8 - - TNMA43NT8PEXT-PT 䖃 0.5 0.189 - - - -
Trapezoid) 6 - - TNMA43NT6PEXT-PT 䖃 0.5 0.189 - - - -
5 - - TNMA54NT5PEXT-PT 䖃 0.625 0.252 - - - -
4 - - TNMA54NT4PEXT-PT 䖃 0.625 0.252 - - - -
3 - - TNMA54NT3PEXT-PT 䖃 0.625 0.252 - - - -
16 - - TNMA43NT16PSTUBE-PT 䖃 0.5 0.189 - - - -
14 - - TNMA43NT14PSTUBE-PT 䖃 0.5 0.189 - - - -
12 - - TNMA43NT12PSTUBE-PT 䖃 0.5 0.189 - - - -
10 - - TNMA43NT10PSTUBE-PT 䖃 0.5 0.189 - - - -
STUB ACME
(29º 8 - - TNMA43NT8PSTUBE-PT 䖃 0.5 0.189 - - - -
Trapezoid) 䖃

Threading Tool
6 - - TNMA43NT6PSTUBE-PT 0.5 0.189 - - - -
5 - - TNMA54NT5PSTUBE-PT 䖃 0.625 0.252 - - - -
4 - - TNMA54NT4PSTUBE-PT 䖃 0.625 0.252 - - - -
3 - - TNMA54NT3PSTUBE-PT 䖃 0.625 0.252 - - - -
API 10 1/16 0.75 TNMC 43 10RD EXT 䖃 0.5 0.189 TNMC 43 10RD INT 䖃 0.5 0.189
Round 8 1/16 0.75 TNMC 43 8RD EXT 䖃 0.5 0.189 TNMC 43 8RD INT 䖃 0.5 0.189
API 5 1/12 1 TNMC 54 5B1 EXT-FC 䖃 0.625 0.252 TNMC 54 5B1 INT-FC 䖃 0.625 0.252
Buttress 5 1/16 0.75 TNMC 54 5B75 EXT-FC 䖃 0.625 0.252 TNMC 54 5B75 INT-FC 䖃 0.625 0.252
16 - - TNMC43NT16PEXT-PT 䖃 0.5 0.189 - - - -
14 - - TNMC43NT14PEXT-PT 䖃 0.5 0.189 - - - -
12 - - TNMC43NT12PEXT-PT 䖃 0.5 0.189 - - - -
10 - - TNMC43NT10PEXT-PT 䖃 0.5 0.189 - - - -
ACME
(29º 8 - - TNMC43NT8PEXT-PT 䖃 0.5 0.189 - - - -
Trapezoid) 6 - - TNMC43NT6PEXT-PT 䖃 0.5 0.189 - - - -
5 - - TNMC54NT5PEXT-PT 䖃 0.625 0.252 - - - -
4 - - TNMC54NT4PEXT-PT 䖃 0.625 0.252 - - - -
3 - - TNMC54NT3PEXT-PT 䖃 0.625 0.252 - - - -
16 - - TNMC43NT16PSTUBE-PT 䖃 0.5 0.189 - - - -
14 - - TNMC43NT14PSTUBE-PT 䖃 0.5 0.189 - - - -
12 - - TNMC43NT12PSTUBE-PT 䖃 0.5 0.189 - - - -
10 - - TNMC43NT10PSTUBE-PT 䖃 0.5 0.189 - - - -
STUB ACME
(29º 8 - - TNMC43NT8PSTUBE-PT 䖃 0.5 0.189 - - - -
Trapezoid) 6 - - TNMC43NT6PSTUBE-PT 䖃 0.5 0.189 - - - -
5 - - TNMC54NT5PSTUBE-PT 䖃 0.625 0.252 - - - -
4 - - TNMC54NT4PSTUBE-PT 䖃 0.625 0.252 - - - -
3 - - TNMC54NT3PSTUBE-PT 䖃 0.625 0.252 - - - -

• For ACME and STUB-ACME inserts can cut crest radius. Crest flat of ACME and STUB-ACME have to cut by another tool. 䖃 : Line up

Tungaloy B469
 C LVOR
E x te r n a l to o l h o l d e r s f o r t h e c h a s e r i n s e r t s

L1
L2

b
h
Right-hand (R) shown.

Metric f L1 L2 h b Insert
CLVOR-25M6 16.1 177.8 32 25 25 CR-8R/10R/11.5NPT/8NPT-3E/4E
CLVOR-32M6 16.1 177.8 32 32 32 CR-8R/10R/11.5NPT/8NPT-3E/4E
CLVOR-40M8 29.8 179.1 32 40 40 CR-5B75-4E

SPARE PARTS
Designation Shim Shim screw Clamp Clamping screw Wrench
CLVOR-25M6 TF1207 SF80 TC-311 STC-4 T-25TORX - 5/32HEX
CLVOR-32M6 TF1207 SF85 TC-311 STC-4 T-25TORX - 5/32HEX
CLVOR-40M8 TF8132-E SF60 TC-311 STC-4 - T-20TORX 5/32HEX

Full profile insert (chaser)

T L
A
Threading Tool

Taper L A T
Connection TPI Designation AH725 Breakerpiece
mm/mm TPF (mm) (mm) (mm)

API 8 1/16 0.75 CR-8R-3E 䖃 16 15 5.2 CR-8R / 10R-3E / 4E-CB

Round
10 1/16 0.75 CR-10R-3E 䖃 16 15.9 5.2 CR-8R / 10R-3E / 4E-CB

API
5 1/16 0.75 CR-5B75-4E 䖃 20.4 15.9 5.1 CR-5B75 / 5B1-4E-CB
Buttress

11.5 1/16 0.75 CR-11.5NPT-4E 䖃 15.9 15.7 4.76 CR-8R / 10R-3E / 4E-CB
NPT
8 1/16 0.75 CR-8NPT-4E 䖃 15.9 15.7 5.2 CR-8R / 10R-3E / 4E-CB

C N G A -3E
A P I R o u n d & b u t t re s s c h a s e r i n s e r t w i t h 2 c o r n e r s f o r t u r n i n g

Full profile insert (chaser)

Taper
Connection TPI Designation AH725
mm/mm TPF

API 10 1/16 0.75 CNGA-10R-3E 䖃

Round 䖃
8 1/16 0.75 CNGA-8R-3E

API
5 1/16 0.75 CNGA-5B75-3E 䖃
Buttress

Note: Toolholder should be designed and ordered individualy. 䖃 : Line up

B470 www.tungaloyamerica.com
S I- C LH O R
I n te r n a l to o l h o l d e r s f o r t h e c h a s e r i n s e r t s

L1

øDs
f
Right-hand (R) shown.

Designation
Metric øDm øDs f L1 Insert
SI-CLHOR-40M6 50.8 40 23.16 400 CR-**I

SPARE PARTS
Designation Clamp Clamping screw Wrench
SI-CLHOR-40M6 TC-311 STC-8 5/32HEX

Full profile insert (chaser)

T L
A

Threading Tool
Taper L A T
Connection TPI Designation AH725 Breakerpiece
mm/mm TPF (mm) (mm) (mm)
8 1/16 0.75 CR-8R-3I 䖃 16 15 5.1 CR-8R / 10R-3I / 4I-CB
API
Round 10 1/16 0.75 CR-10R-3I 䖃 16 15.9 5.1 CR-8R / 10R-3I / 4I-CB

API
5 1/16 0.75 CR-5B75-3I 䖃 16 14.7 5.2 CR-8R / 10R-3I / 4I-CB
Buttress

11.5 1/16 0.75 CR-11.5NPT-4I 䖃 15.9 15.7 4.76 CR-8R / 10R-3I / 4I-CB
NPT
8 1/16 0.75 CR-8NPT-4I 䖃 15.9 15.7 5.2 CR-8R / 10R-3I / 4I-CB

䖃 : Line up

Tungaloy B471
 C R -3E-#1_3
C h a s e r i n s e r t s f o r to o l ro t a t i n g m a c h i n e s

T L T L

A
API Round API Buttress

Taper L A T
Connection TPI Designation AH725 Breakerpiece
mm/mm TPF (mm) (mm) (mm)
8 1/16 0.75 CR-8R-3E #1 䖃 16 14.7 5.2 TD39318R-1-CBW/CAVITY
API
Round 8 1/16 0.75 CR-8R-3E #2 䖃 16 14.9 5.2 TD39328R-2-CBW/CAVITY

8 1/16 0.75 CR-8R-3E #3 䖃 16 15 5.2 TD39338R-3-CBW/CAVITY

5 1/16 0.75 CR-5B75-3E #1 䖃 17 14.6 5.2 TD46015B75-1-CBW/CAVITY

API
Buttress 5 1/16 0.75 CR-5B75-3E #2 䖃 17 14.8 5.2 TD46025B75-2-CBW/CAVITY

5 1/16 0.75 CR-5B75-3E #3 䖃 17 15 5.2 TD46035B75-3-CBW/CAVITY

䖃 : Line up
Threading Tool

B472 www.tungaloyamerica.com
MEMO

Threading Tool

Tungaloy B473
 GrooveLine

C02 www.tungaloyamerica.com
www.tungaloyamerica.com
PARTING, GROOVING &
GROOVE-TURN SYSTEM

Parting, Grooving & Groove-Turn System C002

Tungaloy C001
GrooveLine - Parting, Grooving & Groove-Turn System
Inch Metric

C 0 47
4-cornered inserts with good clamping rigidity for highly precise grooving and parting
W = 0.5 - 3.18 mm (0.020" - 0.125")

C055
Unique insert geometry for highly precise grooving
W = 0.33 - 3.0 mm (0.013" - 0.118")

C009
Innovative clamping system for stable parting operations
W = 1.0 - 2.0 mm (0.039" - 0.079")

C125
Multi-functional tool series for parting, grooving, and turning
W = 4.0 - 6.0 mm (0.157" - 0.236")

C137
Highly rigid clamping system for wide grooving and profiling in one pass
W = 10 - 25 mm (0.394" - 0.984")

C 0 59
Multi-functional tool series for various grooving operations
W = 1.4 - 8.0 mm (0.055" - 0.315")

C 0 92
Variety tool series for a wide range of grooving and parting operations
W = 2.0 - 8.0 mm (0.079" - 0.315")

C 021
G-class inserts with precisely designed chipbreaker for grooving
W = 0.79 - 6.35 mm (0.031" - 0.250")

C044
3-cornered inserts for grooving
W = 1.0 - 2.25 mm (0.039" - 0.089")

Other Grooving & Parting Tool C 014

J-series

C002 www.tungaloyamerica.com
Te tr a Fo rc e - C u t

Tungaloy C003
 E x te r na l G r ooving - Q uick Guide
Max. groove depth: 0.252"
Grooving Tool
M a x . g r o ove d e p t h ( i n)
Series W ( i n) See
0.040 0.080 0.120 0.160 0.200 0.240 page

0.013 0 . 0 31

0.017 - 0.020 0 . 0 47
TetraMini-Cut C055
0.030 - 0.069 0 . 07 9

0.079 - 0.118 0.098

0.013 0.028

0.017 - 0.020 0.043

JTGR/L 0.026 - 0.037 0 . 075 C018

0.039 - 0.071 0.089

0.079 - 0.118 0 .10 2

0.013 0 . 0 31

0.020 0 . 0 47
GBR/L32 C039
0.030 - 0.059 0 . 07 9

0.079 - 0.098 0.098

0.049 - 0.057 0 . 075

GBR/L43 0.059 - 0.091 0 .13 8 C039

0.098 - 0.177 0 .197

0.039 0.059

0.059 0.091

0.079 0 .118

GX-R/LE 0.098 0 .15 0 C036

External 0.118 0 .17 7

0.138 0.209

0.157 - 0.177 0.236

0.020 - 0.030 0.098

0.031 0.063

0.039 - 0.049 0 .13 8

0.055 0 . 07 9

0.058 0.098

0.059 0 . 2 24
TetraForce-Cut C047
0.062 - 0.078 0 .118

0.079 0.252

0.087 - 0.091 0 .13 8

0.094 - 0.098 0 . 2 24

0.106 - 0.113 0 . 24 4
0.118 - 0.125 0.252

First choice M a x . g r o ove d e p t h

Second choice

C004 www.tungaloyamerica.com
E x te r na l G r ooving - Q uick Guide
Max. groove depth: 1.969"

Grooving Tool
M a x . g r o ove d e p t h ( i n)
Series W ( i n) See
0.400 0.800 1.200 1.600 2.000 page

0.118 0.394
MY-T
0.157 0 . 472 C118
FLEX
0.197 0 . 5 51

0.118 - 0.157 0 . 5 51
CTD C120
0.197 20

MY-T 0.079 0.630

C116
CGD 0.118 - 0.315 0.850

0.079 0.630
MY-T
0.118 0.866 C092
G series
0.157 - 0.197 0.984

0.055 0.630

0.079 0.699

TungCut 0.118 - 0.157 0.984 C059

0.197 - 0.236 0.984 1. 2 6 0

0.315 1. 3 78

0.157 0.984 1.181

EasyMulti-Cut 0.197 0.984 1. 2 6 0 C125

0.236 0.984 1. 3 78

0.394 1. 417

TungHeavy 0.591 1. 575

C137
Groove 0.787 1. 575 External

0.984 1. 9 6 9

First choice
M a x . g r o ove d e p t h
Second choice

Tungaloy C005
 Inter na l G r ooving - Q uick Guide
ø D m ( i n)
Grooving Tool
Series W ar See
(in) (in) 0.400 0.800 1.200 1.600 2.000 page
0.039 - 0.059 0 . 315 0.984
0.079
0.059 - 0.079 0 . 5 51 0.984 C031
SNG 0.138
0.059 - 0.118 0 .78 7 0.984
0.138
0.236 0 .78 7 0.984

0.157 0.354 0.984

EasyMulti-Cut 0.433 1. 2 6 0 C125

0.197 0.433 1. 575
0.236 0.433 1. 575

0.236 0.984
0.079
0.315 0.984

0.236 0.984

0.201 0.984
0.118
0.315 1. 2 6 0
0.394 1. 575

0.236 0.984

0.315 1. 2 6 0
TungCut 0.157 C059
0.157 1. 2 2 0

0.394 1. 575

0.197 1. 2 2 0
0.197
0.394 1. 575

0.157 31
0.236
0.394 1. 575

0.197 1. 4 57
0.315
Internal
0.228 1. 6 5 4

0.138 0.984
0.118
0.197 1. 2 6 0

0.197 1. 2 6 0
MY-T
0.157 C092
G series 0.236 1. 575

0.197 1. 2 6 0
0.197
0.236 1. 575

0.013 0.031 1. 2 6 0

GBR/L32 0.020 0.047 1. 2 6 0 C040

0.030- 0.079 1. 2 6 0
0.098

First choice
Second choice
øDm

ar

C006 www.tungaloyamerica.com
Face G r ooving - Q uick Guide
ø D ( i n)

Grooving Tool
Series W ar See
(in) (in) 2.000 4.000 6.000 8.000 10.000 12.000 16.000 20.000 page

0.394 1.181 1. 9 6 9

0.118 0.472 1. 811 7. 8 74

0.591 1. 9 6 9 3 . 9 37

0.394 1.181 - 1. 417

0.472 1.181 - 1. 575
0.157
TungCut 0.630 2.283 9.843 C059
0.787 1. 417 7. 8 74

0.787 2.362 ∞
0.197
0.984 2.362 7. 8 74

0.787 2.362 9.843

0.236
0.984 2.362 15 .74 8

0.394 1.181 19.685

0.118
0.551 1.181 19.685

0.551 1. 3 78 19.685
MY-T
0.157 C092
G series 0.866 1. 3 78 19.685

0.551 1. 3 78 19.685
0.197
0.866 1. 3 78 19.685

1.969 1.181 2.953

0.157
2.559 2.953 19.685

1.969 1. 3 78 2.953
EasyMulti-Cut 0.197 C125
2.559 2.953 19.685

1.969 1.7 72 2.953

0.236
2.559 2.953 19.685

0.039 0.059 2 .16 5 ∞

0.059 0.091 2 .16 5 ∞
0.079 0.118 2 .16 5 ∞ Face
Grooving

GX-F 0.098 0.150 2 .16 5 ∞ C038

0.118 0.177 2 .16 5 ∞
0.138 0.209 2 .16 5 ∞
0.157 - 0.236
0.177 2 .16 5 ∞
First choice
øDm
Second choice
W

ar

Tungaloy C007
 Pa r ting of f - Q uick Guide
M a x . p a r t i n g D i a . ( i n)
Grooving Tool
Series W (in) See
page
0.400 0.500 1.600 2.400 3.200 4.000 8.000

0.020 - 0.030 0 .197

0.031 0 .12 6

0.039 - 0.049 0 .197

0.055 0 .157

0.058 0 .197

0.059 0.449
TetraForce-Cut C047
0.062 - 0.077 0.236

0.079 0.504

0.087 - 0.091 0 . 2 76

0.094 -0.098 0.448

0.106 - 0.113 0.488

0.118 - 0.125 0.504

0.039 0.236

DuoJust-Cut 0.059 0.630 C009

0.079 0.630

0.079 1. 6 9 6

0.118 3 . 9 37
MY-T C092
0.157 3 . 9 37

0.197 4 .724

0.055 1.142

0.079 0.504 1. 9 6 9

0.118 0.504 3 . 9 37

TungCut 0.157 1. 9 6 9 4 .724 C059

Parting-off 0.197 1. 9 6 9 4 .724

0.236 1. 9 6 9 4 .724

0.315 3 .15 0

0.157 1. 9 6 9 3 . 9 37

EasyMulti-Cut 0.197 1. 9 6 9 4 .724 C125

0.236 1. 9 6 9 4 .724

First choice W
Second choice

M a x . p a r t i n g D i a . (m m)

C008 www.tungaloyamerica.com
 - Q uick Guide

Grooving Tool
Great cutting performance in various
parting-off operations

1 2
1 JSXXR/L
W = 0.039" - 0.079" (1 - 2 mm)
Max. parting dia.: 0.630" (16 mm)
Shank size: 0.375" - 0.50" (10 - 20 mm)
Page C010

2 JSXXR/L - S
W = 0.039" - 0.079" (1 - 2 mm)
Max. parting dia.: 0.630" (16 mm)
Shank size:0.375" - 0.50" (10 - 12 mm)
Page C010

3 types of inserts are available for different parting-off diameters can

be mounted in the same pocket of all the toolholders.
- Optimized overhang length for stable machining

Regular-type toolholder Toolholder for sub-spindle

Parting-off

Page C010 Page C010

Others

JXPG06 JXPG12 JXPG16

Max. parting-off dia. Max. parting-off dia. Max. parting-off dia.
ø0.236" (ø6 mm) ø0.472" (ø12 mm) ø0.630" (ø16 mm)
Page C011 Page C011 Page C011

Tungaloy C009
 JSXXR /L
Grooving Tool
Pa r t i n g o f f to o l f o r s w i s s l a t h e s

L1

0.126
h1

h
h2
W

b
f
Right hand (R) shown.

Inch W h b f L1* h1 h2 Insert

JSXXR/L063 0.039 - 0.079 0.375 0.375 0.008 ≤ 4.75 0.375 0.12 JXPG06...,12...,16...
JSXXR/L083 0.039 - 0.079 0.500 0.500 0.008 ≤ 4.75 0.500 0.06 JXPG06...,12...,16...
JSXXR/L103 0.039 - 0.079 0.625 0.625 0.008 ≤ 4.75 0.625 0.06 JXPG06...,12...,16...

Metric W h b f L1* h1 h2 Insert

JSXXR/L1010X09 1-2 10 10 0.2 ≤120 10 3 JXPG06...,12...,16...
JSXXR/L1212F09 1-2 12 12 0.2 ≤85 12 1.5 JXPG06...,12...,16...
JSXXR/L1212X09 1-2 12 12 0.2 ≤120 12 1.5 JXPG06...,12...,16...
JSXXR/L1616X09 1-2 16 16 0.2 ≤120 16 - JXPG06...,12...,16...
JSXXR/L2020H09 1-2 20 20 0.2 ≤100 20 - JXPG06...,12...,16...

* ”L1" is calculated with JXPG16*** insert. When JXPG12*** insert is used, "L1" is shorter 0.079" (2 mm).
When JXPG06*** insert is used, "L1" is shorter 0.157" (4 mm).
Note: The right hand insert (JXPG**R***) is used for the right hand toolholders (JSXXR***), and the left hand insert
(JXPG**L***) is used for the left hand toolholders (JSXXL***).

SPARE PARTS
Designation Clamping screw Wrench
JSXXR... CSTC-4L100DL T-1008/5
JSXXL... CSTC-4L100DR T-1008/5

JSXXR /L-S
Pa r t i n g o f f to o l f o r s u b s p i n d l e i n s w i s s l a t h e s
L1
0.126
h1

h
h2

f2
f2

L3
W

L3
f
b
f

Right-hand Left-hand

Inch W h b f L1* L3* h1 h2 f2 Insert

Parting-off
JSXXR/L063-S 0.039 - 0.079 0.375 0.375 0.008 / 0.217 ≤ 4.75 ≤ 1.03 0.383 0.12 0.226 JXPG06...,12...,16...
JSXXR/L083-S 0.039 - 0.079 0.500 0.500 0.008 / 0.217 ≤ 4.75 ≤ 1.03 0.500 0.06 0.226 JXPG06...,12...,16...
Others

Metric W h b f L1* L3* h1 h2 f2 Insert

JSXXR/L1010X09-S 1-2 10 10 0.2/5.5 ≤120 ≤26 10 3 5.7 JXPG06...,12...,16...
JSXXR/L1212F09-S 1-2 12 12 0.2/5.5 ≤85 ≤26 12 1.5 5.7 JXPG06...,12...,16...
JSXXR/L1212X09-S 1-2 12 12 0.2/5.5 ≤120 ≤30 12 1.5 5.7 JXPG06...,12...,16...

* "L1" and "L3" are calculated with JXPG16*** insert. When JXPG12*** insert is used, "L1" and "L3" are 0.079" (2 mm) shorter.
When JXPG06*** insert is used, "L1" and "L3" are 0.157" (4 mm) shorter.
Note: The right-hand insert (JXPG**R***) is used for the right-hand toolholder (JSXXR***), and the left-hand insert (JXPG**L***)
is used for the left-hand toolholder (JSXXL***).

SPARE PARTS
Designation Clamping screw Wrench
JSXXR**-S CSTC-4L055DL T-1008/5
JSXXL**-S CSTC-4L055DR T-1008/5

Reference pages
Inserts → C011, Standard cutting conditions → C012

C010 www.tungaloyamerica.com
 INSERT
J XP G 06R /L-F (s harp ed g e)

Grooving Tool
rε

W
θ°

r1
L Right hand (R) shown.

W±0.001 W±0.025 rε SH725 Dmax L r1

Designation θ°
(in) (mm) (in) R L (in) (in) (in)

JXPG06R/L10F 0.039 1 0.002 䖃 䖃 0.236 0.413 0 0.104

JXPG06R/L15F 0.059 1.5 0.002 䖃 䖃 0.236 0.413 0 0.104

JXPG06R/L10F-15 0.039 1 0.002 䖃 䖃 0.236 0.413 15 0.104

JXPG06R/L15F-15 0.059 1.5 0.002 䖃 䖃 0.236 0.413 15 0.104

䖃 : Line up
Dmax: Max. parting off dia

J X PG 12R /L-F (s harp ed g e)

rε
W

θ°

r1
L
Right hand (R) shown.

W±0.001 W±0.025 rε SH725 Dmax L r1

Designation θ°
(in) (mm) (in) R L (in) (in) (in)

JXPG12R/L15F 0.059 1.5 0.002 䖃 䖃 0.472 0.492 0 0.206

JXPG12R/L20F 0.079 2 0.002 䖃 䖃 0.472 0.492 0 0.206

JXPG12R/L15F-15 0.059 1.5 0.002 䖃 䖃 0.472 0.492 15 0.206

JXPG12R/L20F-15 0.079 2 0.002 䖃 䖃 0.472 0.492 15 0.206

䖃 : Line up
Dmax: Max. parting off dia

J X PG 16R /L-F (s harp ed g e)

rε
W

θ°

r1
L Right hand (R) shown.

W±0.001 W±0.025 rε SH725 Dmax L r1

Designation θ°
(in) (mm) (in) R L (in) (in) (in)

JXPG16R/L15F 0.059 1.5 0.002 䖃 䖃 0.630 0.571 0 0.274

JXPG16R/L20F 0.079 2 0.002 䖃 䖃 0.630 0.571 0 0.274

JXPG16R/L15F-15 0.059 1.5 0.002 䖃 䖃 0.630 0.571 15 0.274

JXPG16R/L20F-15 0.079 2 0.002 䖃 䖃 0.630 0.571 15 0.274

䖃 : Line up
Dmax: Max. parting off dia

Tungaloy C011
 STAN DARD CUT T ING CONDIT IO N S

Cutting speed Feed

Grooving Tool
ISO Workpiece material Grade
Vc (sfm) f (ipr)
Low carbon steels
SH725 164 - 656 0.00039 - 0.0020
1015, etc.

Carbon steels, Alloy steels

SH725 164 - 656 0.00039 - 0.0020
1055, etc.

Free cutting steels

SH725 164 - 656 0.00039 - 0.0020
SUH22, SUH23, X50CrSi8 2, etc.

Stainless steels
SH725 164 - 656 0.00039 - 0.0020
S30400, etc.

Aluminum alloys
SH725 490 - 660 0.00039 - 0.0020
5056, 6061, etc.

Copper alloy
SH725 330 - 660 0.00039 - 0.0020
C2600, C280C, etc.

Titanium alloys
SH725 98 - 262 0.00039 - 0.0020
Ti-6AI-4V, etc.

Superalloys
SH725 98 - 262 0.00039 - 0.0020
Inconel718, etc.

H O W TO SELECT TOOLS

Large-diameter machining of workpiece with rigidity Small-diameter machining of workpiece with short overhang
Sub-spindle tooling
Main-spindle tooling Sub-spindle tooling Workpiece with long overhang
Short workpiece
at the side of sub-spindle for
with low rigitity
the process after parting-off
Application

Main spindle Sub-spindle Main spindle Sub-spindle Main spindle Sub-spindle Main spindle
Position of parting-off is at the side Position of parting-off is at the side Position of parting-off is at the side Position of parting-off is at the side
of the main spindle of the sub-spindle of the main spindle of the sub-spindle
Toolholder R-hand (JSXXR type) L-hand (JSXXL type) R-hand (JSXXR-S type) L-hand (JSXXL-S type)
Right-hand insert with lead
Left-hand insert Right-hand insert Left-hand insert
Insert angle to remove center core
(JXPG**L*** type) (JXPG**R*** type) (JXPG**L*** type)
(JXPG**R***-15 type)

C012 www.tungaloyamerica.com
 H OW TO S ELECT TOOLHOLDERS F O R S U B -S PI N D L E

L1

Grooving Tool
Parting-off Sub-spindle
diameter diameter

Inch
Sub-spindle dia. Max parting-off dia. Shank size b Tool length L1 Insert Toolholder
ø1.574 ~ ø0.236 0.375 4.567 JXPG06... JSXXR/L063-S

ø1.574 ~ ø0.236 0.500 3.189 JXPG06... JSXXR/L083-S

ø1.574 ~ ø0.472 0.375 4.646 JXPG12... JSXXR/L063-S

ø1.574 ~ ø0.472 0.500 3.268 JXPG12... JSXXR/L083-S

ø1.574 ~ ø0.630 0.375 4.724 JXPG16... JSXXR/L063-S

ø1.574 ~ ø0.630 0.500 3.346 JXPG16... JSXXR/L083-S

ø1.969 ~ ø0.236 0.500 4.567 JXPG06... JSXXR/L083-S

ø1.969 ~ ø0.472 0.500 4.646 JXPG12... JSXXR/L083-S

ø1.969 ~ ø0.630 0.500 3.346 JXPG16... JSXXR/L083-S

ø1.969 ~ ø0.630 0.500 4.724 JXPG16... JSXXR/L083-S

M AX. PA R T ING - OF F DIA . & DEP T H

Main-spindle tooling Sub-spindle tooling
0.031"

0.031"
øD1

øD1

Main spindle Sub-spindle Main spindle

The cutting edge reaches 0.031" beyond the center line in parting-off.
øD1 = Max. parting-off dia.

Parting-off

Others

Tungaloy C013
 Grooving Tool JS VG R /L
E x te r n a l g ro o v i ng to o l ho l d er s f o r sw i ss l a t h e s

ar
C-type

b
f
L1
L2 35°

h1

h
Right hand (R) shown.

Inch W ar h b L1 L2 h1 f Insert
JSVGR/L062.5 0.013 - 0.079 0.028 - 0.217 0.375 0.375 5 0.875 0.375 0.375 JVGR/L...
JSVGR/L082.5 0.013 - 0.079 0.028 - 0.217 0.500 0.500 5 0.875 0.500 0.500 JVGR/L...
JSVGR/L102.5 0.013 - 0.079 0.028 - 0.217 0.625 0.625 5 0.875 0.625 0.625 JVGR/L...

Metric W ar h b L1 L2 h1 f Insert
JSVGR/L1010K-C 0.33 - 2 0.7 - 5.5 10 10 125 23 10 10 JVGR/L...
JSVGR/L1212K-C 0.33 - 2 0.7 - 5.5 12 12 125 23 12 12 JVGR/L...
JSVGR/L1616K 0.33 - 2 0.7 - 5.5 16 16 125 23 16 16 JVGR/L...
• Recommend clamping torque: 2.3 N･m.

SPARE PARTS
Designation Clamping screw Wrench
JSVGR/L... CSTB-3S T-9F(Optional T-9L)

A PPLICA B LE IN S ER T
JVG -t ype ( s harp ed g e)
w rε
G

External
ød T Right hand (R) shown.

Coated Cermet Uncoated

Designation W ⫹0.002
0 W ⫹00.05 rε J740 SH725 NS9530 TH10 ød T G
(in) (mm) (in) R L R L R L R L (mm) (mm) (mm)

JVGR/L033F 0.013 0.33 0 䖃 䖃 䖃 䖃 7.94 3.18 0.7

JVGR/L050F 0.020 0.5 0 䖃 䖃 䖃 䖃 7.94 3.18 1.1

JVGR/L075F 0.030 0.75 0 䖃 䖃 䖃 䖃 7.94 3.18 1.9

JVGR/L095F 0.037 0.95 0 䖃 䖃 䖃 䖃 7.94 3.18 1.9

JVGR/L100F 0.039 1 0 䖃 䖃 䖃 䖃 䖃 䖃 䖃 7.94 3.18 5.5

JVGR/L125F 0.049 1.25 0 䖃 䖃 䖃 䖃 7.94 3.18 5

JVGR/L150F 0.059 1.5 0 䖃 䖃 䖃 䖃 䖃 䖃 䖃 7.94 3.18 5.5

JVGR/L200F 0.079 2 0 䖃 䖃 䖃 䖃 䖃 7.94 3.18 5.5

䖃 : Line up

Reference pages
Standard cutting conditions → C020

C014 www.tungaloyamerica.com
J S XG R /L

Grooving Tool
No-o f f s e t s c re w - o n to o l ho l d er f o r f ro nt & rev e r s e t u r n i n g & ex te r n a l groov i n g

ar
without offset

b
f
C-type

W
L1
L2

h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
JSXGR/L1010K8-C 0.7 - 2 4.5 - 6 10 10 125 29 10 9.9 JXG...
JSXGR/L1212K8-C 0.7 - 2 4.5 - 6 12 12 125 29 12 11.9 JXG...
JSXGR/L1616K8 0.7 - 2 4.5 - 6 16 16 125 29 16 15.9 JXG...
JSXGR/L2020K8 0.7 - 2 4.5 - 6 20 20 125 29 20 19.9 JXG...
JSXGR/L2525K8 0.7 - 2 4.5 - 6 25 25 125 29 25 24.9 JXG...
• Can be wrenched from back side with double socket torx screw. •JSXGR/L-type toolholders are used for JXG-type grooving inserts, JXF-type front-turning inserts and JXR-type
reverse-turning inserts.

SPARE PARTS
Designation Clamping screw Wrench
JSXGR/L... CSTB-4SD T-8F

A PPLICA B LE IN S ER T
J XG -t ype ( w i t h hand and s harp ed g e)
w rε
θ°
G
25

ød T Right hand (R) shown.

Coated Uncoated External

W±0.025 rε J740 TH10 ød T θ° G
Designation
(mm) (mm) (mm) (mm) (mm)
R L R L
JXGR/L8070FA 0.7 0 䖃 䖃 䖃 䖃 8 3.97 15 4.5

JXGR/L8070FA-005 0.7 0.05 䖃 8 3.97 15 4.5

JXGR/L8100FA 1 0 䖃 䖃 䖃 䖃 8 3.97 15 6

JXGR/L8100FA-005 1 0.05 䖃 8 3.97 15 6

JXGR/L8100FA45 1 0 䖃 䖃 8 3.97 15 4.5

JXGR/L8100FA45-005 1 0.05 䖃 8 3.97 15 4.5 Parting-off

JXGR/L8150FA 1.5 0 䖃 䖃 䖃 䖃 8 3.97 15 6

Others
JXGR/L8150FA-005 1.5 0.05 䖃 8 3.97 15 6

JXGR/L8150FA50 1.5 0 䖃 䖃 8 3.97 15 5

JXGR/L8150FA50-005 1.5 0.05 䖃 8 3.97 15 5

JXGR/L8180FA 1.8 0 䖃 䖃 8 3.97 15 6

JXGR/L8180FA-005 1.8 0.05 䖃 8 3.97 15 6

JXGR/L8200FA 2 0 䖃 䖃 䖃 䖃 8 3.97 15 6

JXGR/L8200FA-005 2 0.05 䖃 8 3.97 15 6

JXGR/L8200FN 2 0 䖃 䖃 䖃 䖃 8 3.97 0 6

JXGR/L8200FN-005 2 0.05 䖃 8 3.97 0 6

䖃 : Line up

Reference pages
Standard cutting conditions → C020

Tungaloy C015
 JC C W SR /L
Grooving Tool
E x te r n a l g ro o v i n g & p a r t i n g to o l h o l d e r s f o r s w i s s l a t h e s

L1

b
f
W
L2
øDmax

h1

h
Right hand (R) shown.

Inch W øDmax h b L1 L2 h1 f Insert

JCCWSR/L062 0.079 0.787 0.375 0.375 5 0.748 0.375 0.1875 JCC*200...
JCCWSR/L082 0.079 0.787 0.500 0.500 5 0.748 0.500 0.250 JCC*200...
JCCWSR/L102 0.079 0.787 0.625 0.625 5 0.748 0.625 0.3125 JCC*200...

Metric W øDmax h b L1 L2 h1 f Insert

JCCWSR/L1010K2 2 20 10 10 125 19 10 10 JCC*200...
JCCWSR/L1212K2 2 20 12 12 125 19 12 12 JCC*200...
JCCWSR/L1616K2 2 20 16 16 125 19 16 16 JCC*200...
JCCWSR/L2020K2 2 20 20 20 125 19 20 20 JCC*200...
JCCWSR/L2525K2 2 20 25 25 125 19 25 25 JCC*200...

øDmax: Max. parting off dia.

SPARE PARTS
Designation Clamping screw Wrench
JCCWSR/L... CSTB-4S T-15F

A PPLICA B LE IN S ER T
JC C -t ype ( s harp ed g e)
rε Neutral
(JCCN200F)
rε Right or left hand
(JCCR/L200F)
w

External
L θ L
h

Right hand (R) shown.

Coated Uncoated
Designation W±0.001 W±0.025 rε J740 TH10 h L θ°
(in) (mm) (mm) (mm) (mm)
R L R L
JCCN200F 0.079 2 0 䖃 䖃 4.8 15 0

Parting-off
JCCN200F-005 0.079 2 0.05 䖃 4.8 15 0

JCCR/L200F 0.079 2 0 䖃 䖃 䖃 䖃 4.8 15 15

JCCR/L200F-005 0.079 2 0.05 䖃 䖃 4.8 15 15

䖃 : Line up

Reference pages
Standard cutting conditions → C020

C016 www.tungaloyamerica.com
J C G W SR /L

Grooving Tool
E x te r n a l g ro o v i n g & p a r t i n g to o l h o l d e r s f o r s w i s s l a t h e s

L1

b
f
W
øDmax L2

h1

h
Right hand (R) shown.

Metric W øDmax h b L1 L2 h1 f Insert

JCGWSR/L1010K2 2 20 10 10 125 20 10 10 JCGN200F...
JCGWSR/L1212K2 2 20 12 12 125 20 12 12 JCGN200F...
JCGWSR/L1616K2 2 20 16 16 125 20 16 16 JCGN200F...
øDmax: Max. parting off dia.

SPARE PARTS
Designation Clamping screw Wrench
JCGWSR/L... CSTB-4S T-15F

A PPLICA B LE IN S ER T
J C G -t ype ( sha rp ed g e)
rε
w

L
h

rε
w

8˚ Right hand (R) shown.

Coated Uncoated
Designation W±0.025 rε J740 TH10 h L
(mm) (mm) (mm) (mm)
R L R L
External
JCGN200F 2 0.05 䖃 䖃 3 20

JCGN200FR/L 2 0.05 䖃 䖃 䖃 䖃 3 20

䖃 : Line up

Parting-off

Reference pages
Standard cutting conditions → C020

Tungaloy C017
 Grooving Tool JSTG R /L
E x te r n a l g ro o v i ng to o l ho l d er s f o r sw i ss l at h e s

ar L1

b
f
W
Can be wrenched from
back side with double L2
socket torx screw.

h1

h
h2
Right hand (R) shown.

Inch W ar h b L1 L2 h1 f h2 Insert
JSTGR/L063 0.013 - 0.118 0.028 - 0.102 0.375 0.375 5 0.75 0.375 0.375 0.100 JTGR/L3...
JSTGR/L083 0.013 - 0.118 0.028 - 0.102 0.500 0.500 5 0.75 0.500 0.500 - JTGR/L3...
JSTGR/L103 0.013 - 0.118 0.028 - 0.102 0.625 0.625 5 0.75 0.625 0.625 - JTGR/L3...

Metric W ar h b L1 L2 h1 f h2 Insert
JSTGR/L1010X3 0.33 - 3 0.7 - 2.6 10 10 120 18.5 10 10 2 JTGR/L3...
JSTGR/L1212F3 0.33 - 3 0.7 - 2.6 12 12 85 18.5 12 12 - JTGR/L3...
JSTGR/L1212X3 0.33 - 3 0.7 - 2.6 12 12 120 18.5 12 12 - JTGR/L3...
JSTGR/L1616X3 0.33 - 3 0.7 - 2.6 16 16 120 18.5 16 16 - JTGR/L3...
JSTGL1616K3 0.33 - 3 0.7 - 2.6 16 16 125 18.5 16 16 - JTGR/L3...

• Recommend clamping torque: 1.2 N·m.

SPARE PARTS
Designation Clamping screw Wrench
JSTGR/L... CSTB-4SD T-8F

JS-TG L3
E x te r n a l g ro o v i ng to o l ho l d er s f o r sw i s s l a t h e , p e r p e n d i c u l a r l y m o u n te d i n s e r t s
External

L1
20
W h
ar
f

øDs

b
h
B

h
Left hand (L) shown.

Metric W (mm) W (in) ar øDs f L1 h b B Insert

JS19K-TGL3 0.33 - 3 0.013 - 0.118 0.7 - 2.6 19.05 (0.75") 6 125 18 18 11.5 JTGR3...
JS20K-TGL3 0.33 - 3 0.013 - 0.118 0.7 - 2.6 20 6 125 19 19 11.5 JTGR3...
JS22K-TGL3 0.33 - 3 0.013 - 0.118 0.7 - 2.6 22 6 125 21 21 11.5 JTGR3...
JS25K-TGL3 0.33 - 3 0.013 - 0.118 0.7 - 2.6 25.4 (1.00") 10 125 24 24 12.7 JTGR3...
• Left hand toolholders (TGL3) are used with right hand inserts (JTGR3). • Recommend clamping torque: 3.0 Nm-ft.

SPARE PARTS
Designation Clamping screw Wrench
JS***-TGL3 CSTB-4S T-15F

Reference pages
Inserts → C019 - C020, Standard cutting conditions → C020

C018 www.tungaloyamerica.com
 A PPLICA B LE IN S ER T

Grooving Tool
J TG -type ( sha rp ed g e)
w rε

G
ød T Right hand (R) shown.

Coated Cermet Uncoated

Designation W⫹00.05 W⫹0.002
0
rε SH725 J740 NS9530 TH10 ød T G
(mm) (in) (mm) R L R L R L R L (mm) (mm) (mm)

JTGR/L3033F 0.33 0.013 0.03 䊉 䊉 䊉 䊉 䊉 9.525 3.18 0.7

JTGR/L3033F-005 0.33 0.013 0.05 䊉 9.525 3.18 0.7

JTGR/L3043F 0.43 0.017 0.03 䊉 9.525 3.18 1.1

JTGR/L3050F 0.5 0.020 0.03 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 1.1

JTGR/L3050F-005 0.5 0.020 0.05 䊉 䊉 9.525 3.18 1.1

JTGR/L3065F 0.65 0.026 0.03 䊉 䊉 9.525 3.18 1.9

JTGR/L3065F-010 0.65 0.026 0.1 䊉 9.525 3.18 1.9

JTGR/L3075F 0.75 0.030 0.03 䊉 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 1.9

JTGR/L3075F-010 0.75 0.030 0.1 䊉 䊉 9.525 3.18 1.9

JTGR/L3080F 0.8 0.031 0.03 䊉 䊉 9.525 3.18 1.9

JTGR/L3080F-010 0.8 0.031 0.1 䊉 9.525 3.18 1.9

JTGR/L3085F 0.85 0.034 0.03 䊉 䊉 9.525 3.18 1.9

JTGR/L3095F 0.95 0.037 0.03 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 1.9

JTGR/L3095F-010 0.95 0.037 0.1 䊉 䊉 9.525 3.18 1.9

JTGR/L3100F 1 0.039 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.1

JTGR/L3100F-010 1 0.039 0.1 䊉 䊉 9.525 3.18 2.1

JTGR/L3110F 1.1 0.043 0.05 䊉 䊉 9.525 3.18 2.1

JTGR/L3120F 1.2 0.047 0.05 䊉 䊉 9.525 3.18 2.1

JTGR/L3120F-010 1.2 0.047 0.1 䊉 9.525 3.18 2.1

JTGR/L3125F 1.25 0.049 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.1

JTGR/L3125F-010 1.25 0.049 0.1 䊉 䊉 9.525 3.18 2.1

JTGR/L3130F 1.3 0.051 0.05 䊉 䊉 9.525 3.18 2.1

JTGR/L3140F 1.4 0.055 0.05 䊉 䊉 9.525 3.18 2.1

JTGR/L3140F-010 1.4 0.055 0.1 䊉 9.525 3.18 2.1

JTGR/L3145F 1.45 0.057 0.05 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.1

JTGR/L3145F-010 1.45 0.057 0.1 䊉 9.525 3.18 2.1

JTGR/L3150F 1.5 0.059 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.1

JTGR/L3150F-010 1.5 0.059 0.1 䊉 䊉 9.525 3.18 2.1

JTGR/L3175F 1.75 0.069 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.1

JTGR/L3175F-010 1.75 0.069 0.1 䊉 9.525 3.18 2.1

JTGR/L3180F 1.8 0.071 0.05 䊉 䊉 9.525 3.18 2.1

JTGR/L3200F 2 0.079 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.6

JTGR/L3200F-010 2 0.079 0.1 䊉 䊉 9.525 3.18 2.6

JTGR/L3225F 2.25 0.089 0.05 䊉 䊉 9.525 3.18 2.6

JTGR/L3250F 2.5 0.098 0.05 䊉 䊉 䊉 䊉 䊉 䊉 䊉 9.525 3.18 2.6

JTGR/L3250F-010 2.5 0.098 0.1 䊉 䊉 9.525 3.18 2.6

JTGR/L3275F 2.75 0.108 0.05 䊉 9.525 3.18 2.6

JTGR/L3300F 3 0.118 0.05 䊉 䊉 9.525 3.18 2.6

JTGR/L3300F-010 3 0.118 0.1 䊉 9.525 3.18 2.6

䖃 : Line up

Tungaloy C019
Grooving Tool A PPLICA B LE IN S ER T
JTG -type ( wi t h ho ned ed g e)
w rε

G
ød T
Right hand (R) shown.

Designation J9530
W⫹00.05 W⫹0.002
0 rε ød T G
(mm) (in) (mm) R L (mm) (mm) (mm)
JTGR/L3100 1 0.039 0.05 䖃 9.525 3.18 2.1

JTGR/L3125 1.25 0.049 0.05 䖃 9.525 3.18 2.1

JTGR/L3150 1.5 0.059 0.05 䖃 9.525 3.18 2.1

JTGR/L3200 2 0.079 0.05 䖃 9.525 3.18 2.6

䖃 : Line up

STA N DA RD CUT T ING CONDIT IO N S F O R J S E R I E S G R O OV I N G TO O L S

Workpiece material Grade Cutting speed Feed
ISO
Vc (sfm) f (ipr)

J740 30 - 330 0.001 - 0.004

SH725 160 - 500 0.001 - 0.004

General steels, Free-cutting steels, etc.
NS9530 160 - 500 0.001 - 0.004

J9530 160 - 500 0.001 - 0.004

J740 30 - 330 0.001 - 0.004

Stainless steels, etc.
SH725 50 - 150 0.001 - 0.004

Aluminum alloys, copper alloys, etc. TH10 300 - 650 0.001 - 0.004

Difficult-to-cut materials, titanium alloys, etc. TH10 30 - 100 0.001 - 0.004

C020 www.tungaloyamerica.com
F L A S R /L

Grooving Tool
Exte r n a l g ro o v i n g & t hread i ng to o l ho l d er s f or s w i s s l a t h e s

ar

b
f
3° L1

h1

h
Right hand (R) shown.

Inch W ar h1 h b L1 f Insert
FLASR/L-082D 0.031 - 0.128 0.138 0.500 0.500 0.500 6.000 0.500 FL*-2**R/L...
FLASR-102B 0.031 - 0.128 0.138 0.625 0.625 0.625 4.500 0.625 FL*-2**R...
FLASR/L-103B 0.031 - 0.250 0.210 0.625 0.625 0.625 4.500 0.625 FL*-3**R/L...

Metric W ar h1 h b L1 f Insert
FLASR/L-1212M2 0.79 - 3.25 3.51 12 12 12 150 12 FL*-2**R/L...
FLASR-1616M2 0.79 - 3.25 3.51 16 16 16 150 16 FL*-2**R...
FLASR/L-1616M3 0.79 - 6.35 5.31 16 16 16 125 16 FL*-3**R/L...
Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.

Inch Metric
SPARE PARTS SPARE PARTS
Designation Clamp Clamping screw Wrench Designation Clamp Clamping screw Wrench
FLASR-082D TF-182 S-310 5/32HEX FLASR-1212M2 TF-182 S-310 5/32HEX
FLASL-082D TF-183 S-310 5/32HEX FLASL-1212M2 TF-183 S-310 5/32HEX
FLASR-102B, FLASR-103B TF-184 S-412 5/32HEX FLASR-1616M2, FLASR-1616M3 TF-184 S-412 5/32HEX
FLASL-103B TF-185 S-412 5/32HEX FLASL-1616M3 TF-185 S-412 5/32HEX

F L SR /L
Exte r n a l to o l h o l der s f o r g ro o v i ng & t hread i ng External

ar
W

b
f

3°
L1
h1

Right hand (R) shown.

Inch W ar h1 h b L1 f Insert
FLSR/L-122B 0.031 - 0.128 0.140 0.750 0.750 0.750 4.500 1.000 FL*-2**R/L... Others
FLSR/L-162C 0.031 - 0.128 0.140 1.000 1.000 1.000 5.000 1.250 FL*-2**R/L...
FLSR/L-123B 0.031 - 0.250 0.210 0.750 0.750 0.750 4.500 1.000 FL*-3**R/L...
FLSR/L-163C 0.031 - 0.250 0.210 1.000 1.000 1.000 5.000 1.250 FL*-3**R/L...

Metric W ar h1 h b L1 f Insert
FLSR/L-2020M3 0.79 - 6.35 4.5 20 20 20 125 32 FL*-3**R/L...
FLSR/L-2525M3 0.79 - 6.35 4.5 25 25 25 150 32 FL*-3**R/L...
Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.

Inch Metric
SPARE PARTS SPARE PARTS
Designation Clamp Clamping screw Wrench Designation Clamp Clamping screw Wrench
FLSR-122B, FLSR-162C TF-74 S-310 5/32HEX FLSR-****M3 TF-72 S-412 5/32HEX
FLSL-122B, FLSL-162C TF-75 S-310 5/32HEX FLSL-****M3 TF-73 S-412 5/32HEX
FLSR-123B, FLSR-163C TF-72 S-412 5/32HEX
FLSL-123B, FLSL-163C TF-73 S-412 5/32HEX

Reference pages
Inserts → C026 - C029
Tungaloy C021
 Grooving Tool FLE R /L
E x te r n a l to o l h o l d er s f o r g ro o v i ng & t hread i n g

3°

ar

b
f
W L1

h1

h
L2 Right hand (R) shown.

Inch W ar h1 h b L1 L2 f Insert
FLER/L-122B 0.031 - 0.128 0.140 0.750 0.750 0.750 4.500 1.000 1.000 FL*-2**L/R...
FLER/L-162C 0.031 - 0.128 0.140 1.000 1.000 1.000 5.000 1.000 1.250 FL*-2**L/R...
FLER/L-123B 0.031 - 0.250 0.210 0.750 0.750 0.750 4.500 2.000 1.125 FL*-3**L/R...
FLER/L-163D 0.031 - 0.250 0.210 1.000 1.000 1.000 6.000 2.000 1.250 FL*-3**L/R...
Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.

SPARE PARTS
Designation Clamp Clamping screw Wrench
FLER-122B, FLER-162C TF-75 S-310 7/64HEX
FLEL-122B, FLEL-162C TF-74 S-310 7/64HEX
FLER-123B, FLER-163D TF-73 S-412 5/32HEX
FLEL-123B, FLEL-163D TF-72 S-412 5/32HEX

FLS R /LT
E x te r n a l to o l h o l d er s f o r g ro o v i ng & t hread i n g

External
ar
W

b
f

3°

L1
h1

Right hand (R) shown.

Inch W ar h1 h b L1 f Insert
FLSR/LT-163D 0.094 - 0.189 0.440 1.000 1.000 1.000 6.000 1.250 FLGT-3R/L...
FLSR/LT-203D 0.094 - 0.189 0.440 1.250 1.250 1.250 6.000 1.500 FLGT-3R/L...
Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.
Others
SPARE PARTS
Designation Clamp Clamping screw Wrench
FLSRT-163D, FLSRT-203D TF-72 S-412 5/32HEX
FLSLT-163D, FLSLT-203D TF-73 S-412 5/32HEX

Reference pages
Inserts → C026 - C029

C022 www.tungaloyamerica.com
F L ER /LT

Grooving Tool
Exte r n a l to o l h o l der s f o r g ro o v i ng & t hread i ng

3°

ar

b
f
W L1

h
Right hand (R) shown.

Inch W ar h1 h b L1 f Insert
FLER/LT-163D 0.094 - 0.189 0.440 1.000 1.000 1.000 6.000 1.250 FLGT-3R/L...
FLER/LT-203D 0.094 - 0.189 0.440 1.250 1.250 1.250 6.000 1.500 FLGT-3R/L...
Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.

SPARE PARTS
Designation Clamp Clamping screw Wrench
FLERT-163D, FLERT-203D TF-72 S-412 5/32HEX
FLELT-163D, FLELT-203D TF-73 S-412 5/32HEX

A-FLE R /LT
I n te r n a l to o l h o l d er s f o r g ro o v i ng & t hread i ng

øDm 3° øDs
f

External
L1
W
Right hand (R) shown.
Internal
Inch W øDm øDs L1 f Insert
A20-FLER/LT3 0.094 - 0.189 1.807 1.250 6.000 1.082 FLGT-3R/L...
A24-FLER/LT3 0.094 - 0.189 2.057 1.500 6.000 1.207 FLGT-3R/L...

Note: The right hand toolholders use right hand inserts, and the left hand toolholders use left hand inserts.

SPARE PARTS
Designation Clamp Clamping screw Wrench
A20-FLERT3, A24-FLERT3 TF-72 S-412 5/32HEX
A20-FLELT3, A24-FLELT3 TF-73 S-412 5/32HEX Others

Reference pages
Inserts → C026 - C029

Tungaloy C023
 Grooving Tool A _M -FLER /L
I n te r n a l to o l h o l d er s f o r g ro o v i ng & t hread i n g

øDm 3°

øDs
CM
-7
3

f
L1
W
Right hand (R) shown.

Inch W øDm øDs L1 f Insert

A08-FLER/L2 0.031 - 0.125 0.730 0.500 8.000 0.437 FL*-2**L/R...
A10-FLER2 0.031 - 0.125 1.000 0.625 10.000 0.500 FL*-2**L...
A12-FLER/L2 0.031 - 0.128 1.125 0.750 10.000 0.562 FL*-2**L/R...
A16-FLER/L2 0.031 - 0.128 1.375 1.000 12.000 0.688 FL*-2**L/R...
A16-FLER/L3 0.031 - 0.250 1.375 1.000 12.000 0.688 FL*-3**L/R...

Metric W øDm øDs L1 f Insert

A25M-FLER/L3 0.79 - 6.35 34.9 25 300 17.7 FL*-3**L/R...
A32M-FLER/L3 0.79 - 6.35 44.45 32 350 22.1 FL*-3**L/R...
A40M-FLER3 0.79 - 6.35 50.8 40 350 24.5 FL*-3**L...
Note: The right hand boring bars used for the left hand inserts, and the left hand boring bars used for the right hand inserts.

Inch Metric
SPARE PARTS SPARE PARTS
Designation Clamp Clamping screw Wrench Designation Clamp Clamping screw Wrench
A08-FLER2 TF-146 S-310 5/32HEX A**M-FLER3 TF-73 S-412 5/32HEX
A08-FLEL2 TF-147 S-310 5/32HEX A**M-FLEL3 TF-72 S-412 5/32HEX
A10-FLER2, A12-FLER2,
TF-75 S-310 5/32HEX
A16-FLER2
A12-FLEL2, A16-FLEL2 TF-74 S-310 5/32HEX
A16-FLER3 TF-73 S-412 5/32HEX
A16-FLEL3 TF-72 S-412 5/32HEX

Internal

H S-FLER /L
E xc h a n g e a b l e head s f o r i nter nal g ro o v i ng & t h re a d i n g, a p p l i c a b l e on S - 570 s h a n ks

øDm 3°
øDs

Others
f

L
W
Right hand (R) shown.

Metric W øDm øDs L f Insert

HS40-FLER3W 0.79 - 6.35 56.1 40 40.1 28 FL*-3**L...
HS50-FLER3W 0.79 - 6.35 70.1 50 41.9 35 FL*-3**L...

SPARE PARTS
Designation Clamp Clamping screw Wrench
HS40-FLER3W TF-73 S-412 5/32HEX
HS50-FLER3W TF-73 S-412 5/32HEX

Reference pages
Inserts → C026 - C029

C024 www.tungaloyamerica.com
S-570

Grooving Tool
Steel shanks for exchangeable head

s
øD
L A

Metric øDs L A
S-570-40M-40 40 273 1/2-14NPT
S-570-50M-50 50 366 1/2-14NPT

SPARE PARTS
Designation Clamping screw Wrench
S-570-40M-40 SS100 5/32HEX
S-570-50M-50 SS94 1/4HEX

Internal

Others

Tungaloy C025
 INSERT
Grooving Tool FLG -C B ( W i t h chi p b reaker, met ri c w id t h )
G

W
3°

T
rε
B ød

h
W±0.025 W±0.001 rε AH110 G ød T h B
Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLG-3M100R/L-CB 1 0.039 0.005 - 0.010 䖃 䖃 0.075 0.3750 0.195 0.344 0.4050
FLG-3M150R/L-CB 1.5 0.059 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3M200R/L-CB 2 0.079 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3M250R/L-CB 2.5 0.098 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3M300R/L-CB 3 0.118 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
䖃 : Line up

FLG -C B ( W i t h chi p b reaker)

G
W

3°
T
rε
B ød
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLG-2047R/L-CB 1.20 0.047 0.002 - 0.005 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLG-2062R/L-CB 1.57 0.062 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-2078R/L-CB 1.98 0.078 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-2094R/L-CB 2.39 0.094 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-2125R/L-CB 3.18 0.125 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-3031R/L-CB 0.79 0.031 0.002 - 0.005 䖃 䖃 0.050 0.3750 0.195 0.344 0.4050
FLG-3047R/L-CB 1.19 0.047 0.005 - 0.010 䖃 䖃 0.075 0.3750 0.195 0.344 0.4050
FLG-3062R/L-CB 1.57 0.062 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3072R/L-CB 1.83 0.072 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3078R/L-CB 1.98 0.078 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3088R/L-CB 2.24 0.088 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3094R/L-CB 2.39 0.094 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3097R/L-CB 2.46 0.097 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3125R/L-CB 3.18 0.125 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3189R/L-CB 4.80 0.189 0.020 - 0.025 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
䖃 : Line up

C026 www.tungaloyamerica.com
F LG

Grooving Tool
G

W
3°

T
rε
B ød

h
W±0.025 W±0.001 rε AH110 G ød T h B
Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLG-2031R/L 0.79 0.031 0.002 - 0.005 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLG-2041R/L 1.04 0.041 0.002 - 0.005 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLG-2047R/L 1.19 0.047 0.002 - 0.005 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLG-2058R/L 1.47 0.058 0.005 - 0.010 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLG-2062R/L 1.57 0.062 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-2094R/L 2.39 0.094 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-2125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLG-3031R/L 0.79 0.031 0.002 - 0.005 䖃 䖃 0.050 0.3750 0.195 0.344 0.4050
FLG-3047R/L 1.19 0.047 0.005 - 0.010 䖃 䖃 0.075 0.3750 0.195 0.344 0.4050
FLG-3062R/L 1.57 0.062 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3072R/L 1.83 0.072 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3078R/L 1.98 0.078 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLG-3088R/L 2.24 0.088 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3094R/L 2.39 0.094 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3097R/L 2.46 0.097 0.010 - 0.015 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3105R/L 2.67 0.105 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3110R/L 2.79 0.110 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3122R/L 3.10 0.122 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3142R/L 3.61 0.142 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3156R/L 3.96 0.156 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3178R/L 4.52 0.178 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3185R/L 4.70 0.185 0.020 - 0.025 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3189R/L 4.80 0.189 0.020 - 0.025 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLG-3250R/L 6.35 0.250 0.020 - 0.025 䖃 䖃 0.180 0.3750 0.250 0.344 0.4050
䖃 : Line up

F LG P ( Posi t i v e rake)
G
W

3°
T

rε
B ød
5°
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLGP-2031R/L 0.79 0.031 0.002 - 0.005 䖃 䖃 0.050 0.1875 0.150 0.219 0.2700
FLGP-2062R/L 1.57 0.062 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLGP-2125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.110 0.1875 0.150 0.219 0.2700
FLGP-3047R/L 1.19 0.047 0.005 - 0.010 䖃 䖃 0.075 0.3750 0.195 0.344 0.4050
FLGP-3062R/L 1.57 0.062 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.4050
FLGP-3088R/L 2.24 0.088 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLGP-3094R/L 2.39 0.094 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLGP-3125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLGP-3156R/L 3.96 0.156 0.005 - 0.010 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
FLGP-3189R/L 4.80 0.189 0.020 - 0.025 䖃 䖃 0.180 0.3750 0.195 0.344 0.4050
䖃 : Line up

Tungaloy C027
 FLR -C B ( Ful l no s e rad i us , wi t h chi pb re a ke r )
G

W
Grooving Tool
3°

T
rε
B ød

h
W±0.025 W±0.001 rε AH110 G ød T h B
Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLR-3031R/L-CB 1.57 0.062 0.031 䖃 䖃 0.125 0.3750 0.195 0.344 0.4033
FLR-3047R/L-CB 2.39 0.094 0.047 䖃 䖃 0.180 0.3750 0.195 0.344 0.4025
FLR-3062R/L-CB 3.18 0.125 0.062 䖃 䖃 0.180 0.3750 0.195 0.344 0.4017

䖃 : Line up

FLR ( Ful l no s e rad i us )

G
W

3°

T
rε
B ød
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLR-2031R/L 1.57 0.062 0.031 䖃 䖃 0.110 0.1875 0.150 0.219 0.2683
FLR-2047R/L 2.39 0.094 0.047 䖃 䖃 0.110 0.1875 0.150 0.219 0.2675
FLR-2062R/L 3.18 0.125 0.062 䖃 䖃 0.110 0.1875 0.150 0.219 0.2667
FLR-3031R/L 1.57 0.062 0.031 䖃 䖃 0.125 0.3750 0.195 0.344 0.4033
FLR-3047R/L 2.39 0.094 0.047 䖃 䖃 0.180 0.3750 0.195 0.344 0.4025
FLR-3062R/L 3.18 0.125 0.062 䖃 䖃 0.180 0.3750 0.195 0.344 0.4017
FLR-3078R/L 3.96 0.156 0.078 䖃 䖃 0.180 0.3750 0.195 0.344 0.4008
FLR-3094R/L 4.80 0.189 0.094 䖃 䖃 0.180 0.3750 0.195 0.344 0.4000
䖃 : Line up

FLR P ( Ful l n o s e rad i us and p o s i t i v e ra ke )

G
W

3°
T

rε
B ød
5°
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLRP-3031R/L 1.57 0.062 0.031 䖃 䖃 0.125 0.3750 0.195 0.344 0.4033
FLRP-3047R/L 2.39 0.094 0.047 䖃 䖃 0.180 0.3750 0.195 0.344 0.4025
FLRP-3062R/L 3.18 0.125 0.062 䖃 䖃 0.180 0.3750 0.195 0.344 0.4017
FLRP-3078R/L 3.96 0.156 0.078 䖃 䖃 0.180 0.3750 0.195 0.344 0.4008
FLRP-3094R/L 4.80 0.189 0.094 䖃 䖃 0.180 0.3750 0.195 0.344 0.4000
䖃 : Line up

C028 www.tungaloyamerica.com
F LG D -C B ( S i n g l e ed g e d eep , wi t h chip b re a ke r )
G

Grooving Tool
rε
B ød

h
W±0.025 W±0.001 rε AH110 G ød T h B
Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLGD-3094R/L-CB 2.39 0.094 0.005 - 0.010 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050
FLGD-3125R/L-CB 3.18 0.125 0.005 - 0.010 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050
FLGD-3189R/L-CB 4.80 0.189 0.020 - 0.025 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050

䖃 : Line up

F LG D ( Si ngl e ed g e d eep )
G
W

T
rε
B ød
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLGD-3062R/L 1.57 0.062 0.005 - 0.010 䖃 䖃 0.120 0.3750 0.195 0.344 0.5050
FLGD-3094R/L 2.39 0.094 0.005 - 0.010 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050
FLGD-3125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050
FLGD-3189R/L 4.8 0.189 0.020 - 0.025 䖃 䖃 0.250 0.3750 0.195 0.344 0.5050
䖃 : Line up

F LR D ( Ful l nos e rad i us , s i ng l e ed g e d e e p )

G
W

rε
B ød
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLRD-3062R/L 3.19 0.125 0.062 䖃 䖃 0.250 0.3750 0.195 0.344 0.5016
FLRD-3094R/L 4.8 0.189 0.094 䖃 䖃 0.250 0.3750 0.195 0.344 0.5016

䖃 : Line up

Tungaloy C029
 FLGT ( D oubl e end d eep )
G

W
Grooving Tool

T
rε
B ød

h
W±0.025 W±0.001 rε AH110 G ød T h B
Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLGT-3094R/L 2.39 0.094 0.005 - 0.010 䖃 䖃 0.275 0.3750 0.195 0.344 0.8550
FLGT-3125R/L 3.18 0.125 0.005 - 0.010 䖃 䖃 0.437 0.3750 0.195 0.344 0.8550
FLGT-3189R/L 4.8 0.189 0.020 - 0.025 䖃 䖃 0.437 0.3750 0.195 0.344 0.8550
*Fits FLSLT/RT toolholders
䖃 : Line up

FLR T ( D oubl e end d eep F NR)

G
W

T
rε
B ød
h

W±0.025 W±0.001 rε AH110 G ød T h B

Designation
(mm) (in) (in) R L (in) (in) (in) (in) (in)
FLRT-3062R/L 3.18 0.125 0.062 䖃 䖃 0.437 0.3750 0.195 0.344 0.8550
FLRT-3094R/L 4.80 0.189 0.094 䖃 䖃 0.437 0.3750 0.195 0.344 0.8550
*Fits FLSLT/RT toolholders 䖃 : Line up

FLT-C B ( For t hread i ng )

E

3°
T

60°

rε B ød
h

rε AH725 TPI ød E T h B
Designation
(in) R L Internal External (in) (in) (in) (in) (in)
FLT-3R/L-HCB 0.005 - 0.008 䖃 䖃 5-12 6-20 0.3750 0.098 0.195 0.344 0.3999
FLT-3R/LC-HCB 0.012 - 0.015 䖃 䖃 5-6 6-11 0.3750 0.098 0.195 0.344 0.3999
FLT-3R/L-CB 0.005 - 0.008 䖃 䖃 8-12 8-20 0.3750 0.098 0.195 0.344 0.3999

䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S

Workpiece material Grade Application Cutting speed Feed

ISO
Vc (sfm) f (ipr)
High carbon steel AH110 Grooving 328 - 656 0.005 - 0.014
1045, etc. AH725 Threading 262 - 591 -
Alloy steel AH110 Grooving 164 - 262 0.005 - 0.012
4137, etc. AH725 Threading 197 - 525 -
Stainless steel AH110 Grooving 164 - 492 0.004 - 0.005
S30400, etc. AH725 Threading 164 - 427 -
Gray cast iron AH110 Grooving 164 - 591 0.004 - 0.010
No.250B, etc. AH725 Threading - -
Ductile cast iron AH110 Grooving 164 - 394 0.004 - 0.010
60-40-18, etc. AH725 Threading - -

C030 www.tungaloyamerica.com
SN G R /L

Grooving Tool
Too l h o l d e r s f o r i n ter nal g ro o v i ng

øDs
15°
øDm
Screw-on type Applicable inserts
w L2 L1 h 6GR/L

f
7GR/L

øDs
15°
øDm
Applicable inserts
w L2 8GR/L
h
L1 9GR/L

f
Right hand (R) shown.

Metric Material W øDm øDs f L1 L2 h Max. groove Insert

depth
SNGR/L08H06 STEEL 1-2 8 8 4.7 100 18 7 1.5 6GR/L...
SNGR/L08H07 STEEL 1-2 10 8 5.8 100 23 7 1.5 7GR/L...
SNGR/L10K07 STEEL 1-2 12 10 6.8 125 29 9 1.5 7GR/L...
SNGR/L10K08 STEEL 1.5 - 3.5 14 10 7.6 125 15 9 2 8GR/L...
SNGR/L12M08 STEEL 1.5 - 3.5 16 12 8.6 150 18 11 2 8GR/L...
SNGR/L16Q09 STEEL 1.5 - 3.5 20 16 11.6 180 20 15 3 9GR/L...
SNGR/L20R09 STEEL 1.5 - 3.5 24 20 13.6 200 25 18 3 9GR/L...
SNGR/L08K06SC CARBIDE 1.5 - 3.5 8 8 4.7 125 28 7 1.5 6GR/L...
SNGR/L08K07SC CARBIDE 1.5 - 3.5 10 8 5.8 125 35 7 1.5 7GR/L...
SNGR/L10M07SC CARBIDE 1.5 - 3.5 12 10 6.8 150 45 9 1.5 7GR/L...
SNGR/L10M08SC CARBIDE 1.5 - 3.5 14 10 7.6 150 45 9 2 8GR/L...
SNGR/L12Q08SC CARBIDE 1.5 - 3.5 16 12 8.6 180 - 11 2 8GR/L...
SNGR/L16R09SC CARBIDE 1.5 - 3.5 20 16 11.6 200 - 15 3 9GR/L...

SPARE PARTS
Designation Clamping screw Wrench
SNGR/L***06 CSTB-2L040 T-6F
SNGR/L***07 CSTB-2.2S T-7F
SNGR/L***08 CSTB-2.2 T-7F
SNGR/L***09 CSTB-2.5L080 T-8F
SNGR/L***06SC CSTB-2L040 T-6F
SNGR/L***07SC CSTB-2.2S T-7F
SNGR/L***08SC CSTB-2.2 T-7F
SNGR/L***09SC CSTB-2.5L080 T-8F

Internal

Reference pages
Inserts, Standard cutting conditions → C033

Tungaloy C031
 Grooving Tool C N G R /L
To o l h o l d e r s f o r i nter nal g ro o v i ng

Clamp-on type 15°

øDm

øDs
f
W
L2 h
L1
Right hand (R) shown.

Metric W øDm ar øDs f L1 L2 h Insert

CNGR/L25S15 2-5 32 5 25 18.1 250 30 23 15GR/L...
CNGR/L32T15 2-5 40 5 32 22.1 300 35 30 15GR/L...
CNGR/L40U15 2-5 48 5 40 26.1 350 45 38 15GR/L...

SPARE PARTS
Designation Clamp set Screw Shim Wrench
CNGR... CSP22 DTS5-3.5 SGSR151 T-20F
CNGL... CSP22 DTS5-3.5 SGSL151 T-20F

Optional parts for CNG type toolholders

W h e n u s i n g a s a s c re w - o n t y p e , u s e t h e f o l l o w i n g p a r t s .

Designation Clamping screw Wrench

CNGR/L... CSTB-3.5L T-15F

Internal

Reference pages
Inserts, Standard cutting conditions → C033

C032 www.tungaloyamerica.com
 INSERT

Grooving Tool
* *G R /L
6GR/L L 8GR/L L rε
7GR/L rε w T 9GR/L w T

G
15GR/L Right hand (R) shown.

øD G
B
A
B

øD
A
Right hand (R) shown.

Cermet Uncoated
W±0.025 W±0.001 rε A B T øD L G
Designation NS9530 TH10 UX30
(mm) (in) (in) (in) (in) (in) (in) (in) (in)
R L R L R L
6GR/L100 1 0.039 0.008 䖃 䖃 䖃 䖃 0.187 0.254 0.092 0.091 0.219 0.059

6GR/L150 1.5 0.059 0.008 䖃 䖃 䖃 䖃 䖃 0.187 0.254 0.092 0.091 0.219 0.059

6GR/L200 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 0.187 0.254 0.092 0.091 0.219 0.059

7GR/L100 1 0.039 0.008 䖃 䖃 䖃 0.219 0.290 0.121 0.102 0.219 0.059

7GR/L150 1.5 0.059 0.008 䖃 䖃 䖃 0.219 0.290 0.121 0.102 0.219 0.059

7GR/L200 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 0.219 0.290 0.121 0.102 0.219 0.059

8GR/L150 1.5 0.059 0.008 䖃 䖃 䖃 0.219 0.400 0.152 0.102 0.242 0.079

8GR/L200 2 0.079 0.008 䖃 䖃 䖃 䖃 0.219 0.400 0.152 0.102 0.242 0.079

8GR/L250 2.5 0.098 0.008 䖃 䖃 䖃 䖃 䖃 0.219 0.400 0.152 0.102 0.242 0.079

8GR/L300 3 0.118 0.008 䖃 䖃 䖃 䖃 䖃 0.219 0.400 0.152 0.102 0.242 0.079

8GR/L350 3.5 0.138 0.008 䖃 䖃 0.219 0.400 0.152 0.102 0.242 0.079

9GR/L150 1.5 0.059 0.008 䖃 䖃 䖃 䖃 䖃 0.250 0.510 0.183 0.102 0.305 0.079

9GR/L200 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.250 0.510 0.183 0.102 0.305 0.118

9GR/L250 2.5 0.098 0.008 䖃 䖃 䖃 䖃 䖃 0.250 0.510 0.183 0.102 0.305 0.118

9GR/L300 3 0.118 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.250 0.510 0.183 0.102 0.305 0.118

9GR/L350 3.5 0.138 0.008 䖃 䖃 䖃 䖃 䖃 0.250 0.510 0.183 0.102 0.305 0.118

15GR/L200 2 0.079 0.008 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.118

15GR/L250 2.5 0.098 0.008 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.118

15GR/L300 3 0.118 0.008 䖃 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.118

15GR/L350 3.5 0.138 0.008 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.118

15GR/L400 4 0.157 0.008 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.157

15GR/L450 4.5 0.177 0.008 䖃 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.157

15GR/L500 5 0.197 0.008 䖃 䖃 0.362 0.819 0.201 0.189 0.425 0.197

Note:
䖃㻌㻦㻌㻸㼕㼚㼑㻌㼡㼜
When using a right or left hand insert, the right hand insert is used with right hand toolholder and the left hand insert is used with left hand toolholder.

STA N DA R D CUT T ING CONDIT IONS

Cutting speed Feed
ISO Workpiece material
Vc (sfm) f (ipr)

Medium carbon steels (S45C) 130 - 500 0.002 - 0.006

Cast irons, Light alloys 200 - 650 0.002 - 0.006

Notes:
• Cutting conditions shown above are a guideline only.
• When grooving close to the minimum bore diameter or with long reach conditions, reduce the conditions shown above by approximately 50%.
• To help chip evacuation, use water-soluble cutting fluid. The fluid should be applied sufficiently to the cutting point.
• When using without cutting fluid, reduce both the cutting speeds and feeds shown on the above by 50% at least.

Tungaloy C033
 Grooving Tool C G X R /L
To o l h o l d e r s f o r i nter nal g ro o v i ng

L1

øDs
L2 h
øDm 2°

b
f
2°
Right hand (R) shown.

Metric Material W øDm øDs f L1 L2 h b Max. groove Insert

depth
CGXR/L0016 STEEL 1-3 20 16 11.3 150 24 15 15.5 3 GIR/L52...
CGXR/L0020 STEEL 1-3 24 20 13.3 180 30 18 19 3 GIR/L52...
CGXR/L0025 STEEL 1-5 32 25 18 200 38 23 24 5.3 GIR/L63...
CGXR/L0032 STEEL 1-5 40 32 23 250 48 30 31 5.3 GIR/L63...
CGXR/L0040 STEEL 1-5 48 40 27 300 60 37 38.5 5.3 GIR/L63...
CGXR/L16SC CARBIDE 1-3 20 16 11.3 200 24 15 - 3 GIR/L52...
• When using a right or left hand insert, the right hand insert (GIR) is used for the right hand toolholders (CGXR) , and the left hand insert (GIL) is used for the left hand
toolholders (CGXL).

SPARE PARTS
Designation Clamp set Wrench 1 Wrench 2
CGXR/L0016/20 CSW-0 - P-2.5T
CGXR/L0025/32/40 CSW-2 P-4 -
CGXR/L16SC CSW-0 - P-2.5T

Internal

Reference pages
Inserts, Standard cutting conditions → C035

C034 www.tungaloyamerica.com
 INSERT
G I R /L

Grooving Tool
G
L T

w
2°

s
rε
Right hand (R) shown.

W±0.05 rε Cermet Uncoated S T L G

Designation
(mm) (mm) NS9530 TH10 (mm) (mm) (mm) (mm)
GIR5210-02 1 0.2 䖃 䖃 3.5 4.4 15 1.5

GIR5215-02 1.5 0.2 䖃 䖃 3.5 4.4 15 2.3

GIR5220-02 2 0.2 䖃 䖃 3.5 4.4 15 3

GIR5225-02 2.5 0.2 䖃 䖃 3.5 4.4 15 3

GIR5230-02 3 0.2 䖃 䖃 3.5 4.4 15 3

GIR6310-02 1 0.2 䖃 䖃 5.5 6.4 24 1.5

GIR6315-02 1.5 0.2 䖃 䖃 5.5 6.4 24 2.3

GIR6320-02 2 0.2 䖃 䖃 5.5 6.4 24 3

GIR6325-02 2.5 0.2 䖃 䖃 5.5 6.4 24 3.8

GIR6330-02 3 0.2 䖃 䖃 5.5 6.4 24 4.5

GIR6335-02 3.5 0.2 䖃 䖃 5.5 6.4 24 5.3

GIR6340-02 4.0 0.2 䖃 䖃 5.5 6.4 24 5.3

GIR6345-02 4.5 0.2 䖃 䖃 5.5 6.4 24 5.3

GIR6350-02 5 0.2 䖃 䖃 5.5 6.4 24 5.3

Note: 䖃 : Line up
When using a right or left hand insert, the right hand insert is used with right hand toolholder and the left hand insert is used with left hand toolholder.

STA N DA R D CUT T ING CONDIT IONS ( E X T E R N AL & I N T E R N AL G R O OV I N G )

Feed
Cutting speed
ISO Workpiece material Grade f (ipr)
Vc (sfm)
W < 0.079" W = 0.079" - 0.157" W > 0.157"

Carbon steels NS9530 260 - 500 0.002 - 0.004 0.003 - 0.006 0.003 - 0.008

Cast irons, Light alloys TH10 200 - 500 0.002 - 0.004 0.003 - 0.006 0.003 - 0.008

Tungaloy C035
 Grooving Tool G X -R /LE
E x te r n a l to o l h o l d e r s f o r g ro o v i n g , w i t h d o u b l e - e n d e d i n s e r t s

ar L1

2°

b
f
w
2°
L2

h1

h
Right hand (R) shown.

Inch W ar h b L1 L2 h1 f Insert
GX-1212REU 0.039 - 0.177 0.059 - 0.236 0.75 0.75 5.00 1.38 0.75 1.00 XGR63...
GX-1616REU 0.039 - 0.177 0.059 - 0.236 1.00 1.00 5.90 1.38 1.00 1.25 XGR63...

Metric W ar h b L1 L2 h1 f Insert
GX-2020R/LE 1 - 4.5 1.5 - 6 20 20 125 35 20 25 XGR/L63...
GX-2525R/LE 1 - 4.5 1.5 - 6 25 25 150 35 25 32 XGR/L63...

• When using a right or left hand insert, the right hand insert (XGR) is used for the right hand toolholders (GX-****RE) , and the left hand insert (XGL) is used for the left hand toolholders (GX-****LE).

SPARE PARTS
Designation Clamp Clamp Shim Shim screw Wrench
screw
GX-1212REU,
CP81A RT-1 SL-6R BHM4-8 P-4
GX-2020RE
GX-2020LE CP81A RT-1 SL-6L BHM4-8 P-4
GX-1616REU,
CP81A RT-1 SL-1R BHM4-8 P-4
GX-2525RE
GX-2525LE CP81A RT-1 SL-1L BHM4-8 P-4
Note:
Max.groove width and max. groove depth shown in the above table are the values
when the insert having the largest cutting edge width is used.

G X -R /LI
External To o l h o l d e r s f o r i nter nal g ro o v i ng

2° L1
Internal øDm b
f

W
ar

Enlarged view
ar

h1

2° 2°
W 2° 2°
L2 Right hand (R) shown.

Inch W øDm ar h b L1 L2 h1 f Insert

GX-1212RIU 0.039 - 0.177 2.165 0.059 - 0.236 0.750 0.75 6.30 2.36 0.75 1.37 XGL63...
GX-1616RIU 0.039 - 0.177 2.165 0.059 - 0.236 1.00 1.00 7.87 1.96 1.00 1.37 XGL63...

Metric W øDm ar h b L1 L2 h1 f Insert

GX-2525R/LI 1 - 4.5 55 1.5 - 6 25 25 200 70 25 35 XGL/R63...
• When using a right or left hand insert, the right hand insert (XGR) is used for the left hand toolholders (GX-****LI) , and the left hand insert (XGL) is used for the right hand toolholders (GX-****RI).

SPARE PARTS
Designation Clamp Clamp Shim Shim screw Wrench
screw
GX-1212RIU CP81B RT-1 SL-7R BHM4-8 P-4
GX-2525RI CP81B RT-1 SL-2R BHM3-8 P-4
GX-1616RIU,
CP81B RT-1 SL-2L BHM3-8 P-4
GX-2525LI

Reference pages
Inserts, Standard cutting conditions → C037

C036 www.tungaloyamerica.com
 INSERT

Grooving Tool
XG R /L
8.0 20.0

4.50
2°

w
G

2−rε Right hand (R) shown.

Cermet Uncoated
Designation W±0.05 W±0.002 rε NS9530 TH10 UX30 G
(mm) (in) (mm) (mm)
R L R L R L
XGR/L6310-02 1 0.039 0.2 䖃 䖃 䖃 䖃 䖃 䖃 1.5

XGR/L6315-02 1.5 0.059 0.2 䖃 䖃 䖃 䖃 䖃 䖃 2.3

XGR/L6320-02 2 0.079 0.2 䖃 䖃 䖃 䖃 䖃 䖃 3

XGR/L6325-02 2.5 0.098 0.2 䖃 䖃 䖃 䖃 䖃 䖃 3.8

XGR/L6330-02 3 0.118 0.2 䖃 䖃 䖃 䖃 䖃 䖃 4.5

XGR/L6335-02 3.5 0.138 0.2 䖃 䖃 䖃 䖃 䖃 䖃 5.3

XGR/L6340-02 4 0.157 0.2 䖃 䖃 䖃 䖃 䖃 䖃 6

XGR/L6345-02 4.5 0.177 0.2 䖃 䖃 䖃 䖃 䖃 䖃 6

Note;
For internal machining, use right-hand toolholder (GX-****RI) with left-hand insert (XGL****),
䖃 : Line up
and use left-hand toolholder (GX-****LI) with right-hand insert (XGR****).
For external machining, use right-hand toolholder (GX-****RE) with right-hand insert (XGR****),
and use left-hand toolholder (GX-****LE) with left-hand insert (XGL****).

XG R /L-Q B N
8.0 20
2°
4.5
w

2−rε Right hand (R) shown.

T-CBN
Designation W±0.05 W±0.002 rε BX360 G
(mm) (in) (mm) R L (mm)
XGL6310S-QBN 1 0.039 0.2 䖃 2.3

XGR/L6315S-QBN 1.5 0.059 0.2 䖃 䖃 2.3

XGR/L6320S-QBN 2 0.079 0.2 䖃 䖃 3

XGR/L6325S-QBN 2.5 0.098 0.2 䖃 䖃 3.8

XGR/L6330S-QBN 3 0.118 0.2 䖃 䖃 4.5

XGR/L6335S-QBN 3.5 0.138 0.2 䖃 䖃 5.3

XGR/L6340S-QBN 4 0.157 0.2 䖃 䖃 6

XGR/L6345S-QBN 4.5 0.177 0.2 䖃 䖃 6

䖃 : Line up
Note;
For internal machining, use right-hand toolholder (GX-****RI) with left-hand insert (XGL****),
and use left-hand toolholder (GX-****LI) with right-hand insert (XGR****).
For external machining, use right-hand toolholder (GX-****RE) with right-hand insert (XGR****),
and use left-hand toolholder (GX-****LE) with left-hand insert (XGL****).

STA N DA R D CUT T ING CONDIT ION S

Cutting speed Feed
ISO Workpiece material Grade f (ipr)
vc (sfm)
W < 0.078" W = 0.078" - 0.157" W > 0.157"
NS9530 260 - 650 0.001 - 0.004 0.003 - 0.008 0.003 - 0.010
Carbon steels TX10S 200 - 500 0.001 - 0.004 0.003 - 0.008 0.003 - 0.010
UX30 200 - 500 0.001 ~ 0.004 0.003 - 0.008 0.003 - 0.010

Cast irons , Light alloys TH10 200 - 500 0.001 - 0.004 0.003 - 0.008 0.03 - 0.010

Hardened steels BX360 60 - 500 0.001 - 0.15 0.001 - 0.15 0.001 - 0.006

Tungaloy C037
 Grooving Tool G X -R /LF
To o l h o l d e r s f o r f ace g ro o v i ng

w
L2
Enlarged view øDm

f f1

b
2°
w

2°
ar 55°
L1

h
2°

h1
Right hand (R) shown.

Metric W øDm ar h b L1 L2 h1 f f1 Insert

GX-2525R/LF 1 - 4.5 55 1.5 - 6 25 25 150 35 25 32 15 XNL/R63...
• When using a right or left hand insert, the right hand insert (XNR) is used for the left hand toolholders (GX-...LF) , and the left hand insert (XNL) is used for the right hand
toolholders (GX-...RF).

SPARE PARTS
Designation Clamp set Clamping Shim Shim screw Wrench
screw
GX-2525RF CP81A RT-1 SL-3R BHM4-8 P-4
GX-2525LF CP81A RT-1 SL-3L BHM4-8 P-4

INSERT
X N R /L
20.0 8.0
2°
G
w
4.5

2−rε Left hand (L) shown.

Cermet Uncoated
Designation NS9530 TH10
W±0.05 rε G
(mm) (mm) R L R L (mm)

XNR/L6310-02 1 0.2 䖃 䖃 䖃 䖃 1.5

XNR/L6315-02 1.5 0.2 䖃 䖃 䖃 䖃 2.3

XNR/L6320-02 2 0.2 䖃 䖃 䖃 䖃 3

XNR/L6325-02 2.5 0.2 䖃 䖃 䖃 䖃 3.8

Face
XNR/L6330-02 3 0.2 䖃 䖃 䖃 䖃 4.5
Grooving
XNR/L6335-02 3.5 0.2 䖃 䖃 䖃 䖃 5.3

XNR/L6340-02 4 0.2 䖃 䖃 䖃 䖃 6

XNR/L6345-02 4.5 0.2 䖃 䖃 䖃 䖃 6

䖃 : Line up

C038 www.tungaloyamerica.com
TGTSR /L

Grooving Tool
E x te r n a l to o l h o l d e r s f o r g ro o v i n g , w i t h t r i p l e c o r n e r i n s e r t

ar

b
f
w
L2
L1

h1 ( 5˚ )

h
Right hand (R) shown.

Inch W ar h b L1 L2 h1 f
TGTSR16-3 0.013 ~ 0.100 0.110 1.00 1.00 6 0.98 1.00 1.00
TGTSR16-4-1 0.040 ~ 0.057 0.100 1.00 1.00 6 1.00 1.00 1.00
TGTSR16-4-2 0.060 ~ 0.090 0.160 1.00 1.00 6 1.00 1.00 1.00
TGTSR16-4-3 0.100 ~ 0.180 0.210 1.00 1.00 6 1.00 1.00 1.00

Metric W ar h b L1 L2 h1 f
TGTSR/L2020K16 0.33 - 2.5 2.5 20 20 125 25 20 25
TGTSR/L2525M16 0.33 - 2.5 2.5 25 25 150 25 25 30
TGTSR/L2020K22-1 1 - 1.45 2 20 20 125 25 20 25
TGTSR/L2020K22-2 1.5 - 2.3 3.5 20 20 125 25 20 25
TGTSR/L2020K22-3 2.5 - 4.5 5 20 20 125 25 20 25
TGTSR/L2525M22-1 1 - 1.45 2 25 25 150 25 25 30
TGTSR/L2525M22-2 1.5 - 2.3 3.5 25 25 150 25 25 30
TGTSR/L2525M22-3 2.5 - 4.5 5 25 25 150 25 25 30

• See below Applicable insert table.

• The right hand insert (GBR) is used for the right hand toolholders (TGTSR), and the left hand insert (GBL) is used for the left hand toolholders (TGTSL).

Designation Applicable insert

TGTSR16-3 GBR/L32...
TGTSR16-4-1 GBR43050R ~ 145
TGTSR16-4-2 GBR43150 ~ 230
TGTSR16-4-3 GBR43250 ~ 450
TGTSR/L2020K16 GBR/L32... External

TGTSR/L2525M16 GBR/L32...
TGTSR/L2020K22-1 GBR/L43125 ~ 145 GBR/L43050R
TGTSR/L2020K22-2 GBR/L43150 ~ 230 GBR/L43075R ~ 100R
TGTSR/L2020K22-3 GBR/L43250 ~ 450 GBR/L43125R ~ 200R
TGTSR/L2525M22-1 GBR/L43125 ~ 145 GBR/L43050R
TGTSR/L2525M22-2 GBR/L43150 ~ 230 GBR/L43075R ~ 100R
TGTSR/L2525M22-3 GBR/L43250 ~ 450 GBR/L43125R ~ 200R

SPARE PARTS
Designation Clamp Clamping screw Wrench
TGTSR16-3 CP900 MCS520-2.5 P-2.5 Others
TGTSR16-4... CP910 MCS520-2.5 P-2.5
TGTSR/L*****16 CP900 MCS520-2.5 P-2.5
TGTSR/L*****22... CP910 MCS520-2.5 P-2.5

Reference pages
Inserts → C041 - C042, Standard cutting conditions → C042

Tungaloy C039
 Grooving Tool TGTTR /L
Pe r p e n d i c u l a r to o l h o l d e r s f o r ex te r n a l g ro o v i n g , w i t h t r i p l e c o r n e r i n s e r t s

b
f
w

ar
h1 ( 5˚ ) L2
L1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f
TGTTR/L2020K16 0.33 - 2.5 2.5 20 20 125 20 20 27
TGTTR/L2525M16 0.33 - 2.5 2.5 25 25 150 20 25 32
TGTTR/L2020K22-1 1 - 1.45 2 20 20 125 20 20 27
TGTTR/L2020K22-2 1.5 - 2.3 3.5 20 20 125 20 20 27
TGTTR/L2020K22-3 2.5 - 4.5 5 20 20 125 20 20 27
TGTTR/L2525M22-1 1 - 2.3 2 25 25 150 20 25 32
TGTTR/L2525M22-2 1.5 - 2.3 3.5 25 25 150 20 25 32
TGTTR/L2525M22-3 2.5 - 4.5 5 25 25 150 20 25 32

• See below Applicable insert table.

• The left hand insert (GBL) is used for the right hand toolholders (TGTTR), and the right hand insert (GBR) is used for the left hand toolholders (TGTTL).
Designation Applicable insert
TGTTR/L2020K16 GBL/R32... SPARE PARTS
TGTTR/L2525M16 GBL/R32... Designation Clamp Clamping screw Wrench
TGTTR/L*****16 CP900 MCS520-2.5 P-2.5
TGTTR/L2020K22-1 GBL/R43125 ~ 145 GBL/R43050R
TGTTR/L*****22... CP910 MCS520-2.5 P-2.5
TGTTR/L2020K22-2 GBL/R43150 ~ 230 GBL/R43075R ~ 100R
TGTTR/L2020K22-3 GBL/R43250 ~ 450 GBL/R43125R ~ 200R
TGTTR/L2525M22-1 GBL/R43125 ~ 145 GBL/R43050R
TGTTR/L2525M22-2 GBL/R43150 ~ 230 GBL/R43075R ~ 100R
TGTTR/L2525M22-3 GBL/R43250 ~ 450 GBL/R43125R ~ 200R

External S-S GTR /L

To o l h o l d e r s f o r i nter nal g ro o v i ng

Internal
øDm 16˚ L2
øDs
f

h
ar

w L1

Right hand (R) shown.

Others Inch W øDm ar øDs f L1 L2 h Insert
S16R-SGTR/L3 0.013 - 0.098 1.38 0.100 1.00 0.690 7.78 1.18 0.910 GBL/R32...

Metric W øDm ar øDs f L1 L2 h Insert

S25R-SGTR/L16 0.33 - 2.5 35 2 25 17.5 200 30 23 GBL/R32...
S32S-SGTR/L22 1.25 - 4.5 40 2.5 32 23 250 30 30 GBL/R43...
• When using a right or left hand insert, the right hand insert (GBR) is used for the left hand toolholders (SGTL) , and the left hand insert (GBL) is used for the right hand
toolholders (SGTR).

SPARE PARTS
Designation Clamping screw Wrench
S16R-SGTR/L3
CSTB-4S T-15F
S25R-SGTR/L16
S32S-SGTR/L22 CSTB-5S T-20F

Reference pages
Inserts → C041 - C042, Standard cutting conditions → C042

C040 www.tungaloyamerica.com
 A PPLICA B LE IN S ER T
G B R /L32

Grooving Tool
T
2- rε G

11˚
°
85

W
rε
60˚ ød Right hand (R) shown.

Coated Cermet Uncoated

Designation AH710 NS9530 KS05F
W±0.025 W±0.001 rε G ød T
(mm) (in) (mm) R L R L R L (mm) (mm) (mm)

GBR/L32033 0.33 0.013 0.03 䖃 䖃 䖃 䖃 0.8 9.525 3.18

GBR/L32050 0.5 0.020 0.05 䖃 䖃 䖃 䖃 1.2 9.525 3.18

GBR/L32075 0.75 0.030 0.05 䖃 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32095 0.95 0.037 0.05 䖃 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32100 1 0.039 0.05 䖃 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32125 1.25 0.049 0.2 䖃 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32145 1.45 0.057 0.2 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32150 1.5 0.059 0.2 䖃 䖃 䖃 䖃 2 9.525 3.18

GBR/L32200 2 0.079 0.2 䖃 䖃 䖃 䖃 2.5 9.525 3.18

GBR/L32250 2.5 0.098 0.2 䖃 䖃 䖃 䖃 2.5 9.525 3.18

䖃 : Line up

G B R /L43
G T
2- rε
11˚

°
W

85
rε
60˚ ød Right hand (R) shown.

Coated Cermet Uncoated

Designation AH710 NS9530 KS05F
W±0.025 W±0.001 rε G ød T
(mm) (in) (mm) R L R L R L (mm) (mm) (mm)

GBR/L43125 1.25 0.049 0.2 䖃 䖃 䖃 䖃 2 12.7 4.76

GBR/L43145 1.45 0.057 0.2 䖃 䖃 䖃 䖃 2 12.7 4.76

GBR/L43150 1.5 0.059 0.2 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43175 1.75 0.069 0.2 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43185 1.85 0.073 0.2 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43200 2 0.079 0.2 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43230 2.3 0.091 0.2 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43250 2.5 0.098 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43265 2.65 0.104 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43280 2.8 0.110 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43300 3 0.118 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43330 3.3 0.130 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43350 3.5 0.138 0.3 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43400 4 0.157 0.4 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43430 4.3 0.169 0.4 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43450 4.5 0.177 0.4 䖃 䖃 䖃 䖃 5 12.7 4.76

䖃 : Line up

Tungaloy C041
 A PPLICA B LE IN S ER T
Grooving Tool G B R /L43-R (Rad i us )
T rε
rε G

W
ød Right hand (R) shown.

Coated Cermet Uncoated

Designation AH710 NS9530 KS05F
W±0.025 W±0.001 rε G ød T
(mm) (in) (mm) R L R L R L (mm) (mm) (mm)

GBR/L43050R 1 0.039 0.5 䖃 䖃 䖃 䖃 䖃 2 12.7 4.76

GBR/L43075R 1.5 0.059 0.75 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43100R 2 0.079 1 䖃 䖃 䖃 䖃 䖃 3.5 12.7 4.76

GBR/L43125R 2.5 0.098 1.25 䖃 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43150R 3 0.118 1.5 䖃 䖃 䖃 䖃 䖃 5 12.7 4.76

GBR/L43200R 4 0.157 2 䖃 䖃 䖃 䖃 䖃 5 12.7 4.76

䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S

Cutting speed Feed
ISO Workpiece material Hardness Grade
Vc (sfm) f (ipr)

150 - 240HB NS9530 330 - 650 0.001 - 0.010

Carbon steels, Alloy steels
1045 SAE, 4140 SAE, etc.
150 - 240HB AH710 200 - 500 0.002 - 0.010

Stainless steels
) 240HB AH710 200 - 500 0.002 - 0.010
303, 304, etc.
Cast irons Tensile strength
AH710 200 - 500 0.002 - 0.010
250, etc. ) 350 N/mm2
Non-ferrous metals
- KS05F 650 - 980 0.002 - 0.010
External Aluminum, etc.

SGTR /L
E x te r n a l to o l h o l d e r s f o r g ro o v i n g , w i t h t r i p l e c o r n e r i n s e r t s

L1
L2
W

b
f

ar
h1

Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
SGTR1616-3 1.15 - 2.7 1.5 - 3 16 16 100 20 16 20 GLR/L3...
SGTR/L2020-3 1.15 - 2.7 1.5 - 3 20 20 125 20 20 25 GLR/L3...
SGTR/L2525-3 1.15 - 2.7 1.5 - 3 25 25 150 20 25 32 GLR/L3...
SGTR/L2020-4 1.15 - 4.2 1.5 - 4 20 20 125 30 20 25 GLR/L4...,GOR/L4...
SGTR/L2525-4 1.15 - 4.2 1.5 - 4 25 25 150 30 25 32 GLR/L4...,GOR/L4...

SPARE PARTS
Designation Clamping screw Wrench
SGTR/L****-3 CSTB-4 T-15F
SGTR/L****-4 CSTB-5 T-20F

Reference pages
Inserts, Standard cutting conditions → C043

C042 www.tungaloyamerica.com
 A PPLICA B LE IN S ER T
GOR /L ( O-ri ng)

Grooving Tool
G

w
T
2- rε

ød
Right hand (R) shown.

Cermet Uncoated
Designation W ⫹⫹0.004 NS9530 UX30
W⫹⫹0.1
0.05 0.002 rε G ød T
(mm) (in) (mm) R L R L (mm) (mm) (mm)

GOR/L4190 2.5 0.098 0.4 䖃 䖃 1.5 12.7 4.76

GOR/L4240 3.2 0.126 0.4 䖃 䖃 2 12.7 4.76

GOR/L4310 4.1 0.161 0.7 䖃 䖃 2.5 12.7 4.76

䖃 : Line up

GLR /L ( Lock- ri ng )
G
w
T

2- rε

ød Right hand (R) shown.

Cermet Uncoated
Designation W ⫹⫹0.004 NS9530 UX30
W⫹⫹0.1
0.05 0.002 rε G ød T
(mm) (in) (mm) R L R L (mm) (mm) (mm)

GLR/L3115 1.15 0.045 0.1 䖃 䖃 䖃 䖃 1.5 9.525 3.18

GLR/L3135 1.35 0.053 0.1 䖃 䖃 䖃 1.5 9.525 3.18

GLR/L3165 1.65 0.065 0.1 䖃 䖃 䖃 2 9.525 3.18

GLR/L3175 1.75 0.069 0.1 䖃 䖃 䖃 䖃 2 9.525 3.18

GLR/L3195 1.95 0.077 0.1 䖃 䖃 䖃 䖃 2.5 9.525 3.18

GLR/L3220 2.2 0.087 0.1 䖃 䖃 䖃 3 9.525 3.18

GLR/L3270 2.7 0.106 0.1 䖃 䖃 䖃 3 9.525 3.18

GLR/L4115 1.15 0.045 0.1 䖃 䖃 1.5 12.7 4.76

GLR/L4135 1.35 0.053 0.1 䖃 䖃 1.5 12.7 4.76

GLR/L4165 1.65 0.065 0.1 䖃 䖃 2 12.7 4.76

GLR/L4175 1.75 0.069 0.1 䖃 䖃 2 12.7 4.76

GLR/L4190 1.9 0.075 0.1 䖃 2.5 12.7 4.76

GLR/L4195 1.95 0.077 0.1 䖃 䖃 2.5 12.7 4.76

GLR/L4220 2.2 0.087 0.1 䖃 䖃 䖃 3.5 12.7 4.76

GLR/L4270 2.7 0.106 0.1 䖃 䖃 3.5 12.7 4.76

GLR/L4320 3.2 0.126 0.1 䖃 䖃 䖃 4 12.7 4.76

GLR/L4420 4.2 0.165 0.1 䖃 䖃 䖃 4 12.7 4.76

䖃 : Line up

STA N DA R D CUT T ING CONDIT ION S

Feed
Cutting speed f (ipr)
ISO Workpiece material Grade
Vc (sfm)
W < 0.078" W = 0.078" - 0.157" W > 0.157"
NS9530 260 - 650 0.002 - 0.004 0.003 - 0.008 0.003 - 0.010
Carbon steels
UX30 200 - 500 0.002 - 0.004 0.003 - 0.008 0.003 - 0.010

Tungaloy C043
 GTGN
Grooving Tool C ER /L
E x te r n a l g ro o v i ng to o l ho l d er s, al ter nat i v e c l a m p i n g of s c re w - on or c l a m p - on (DT t y p e on l y )

L1
L2

b
f
10°

h1

h
Right hand (R) shown.

Inch h b L1 L2 h1 f Insert
CER/L123DT 0.750 0.750 5.000 0.870 0.750 1.000 GTGN16...
CER/L163DT 1.000 1.000 6.000 1.000 1.000 1.250 GTGN16...
CER203DT 1.250 1.250 6.000 1.250 1.250 1.500 GTGN16...

Metric h b L1 L2 h1 f Insert
CER/L1212H16DT 12 12 100 24 12 16 GTGN16...
CER/L1616H16DT 16 16 100 24 16 20 GTGN16...
CER/L2020K16DT 20 20 125 24 20 25 GTGN16...
CER/L2525M16DT 25 25 150 28 25 32 GTGN16...
CER3232P16T 32 32 170 32 32 40 GTGN16...
• A clamp set for CER/L type consists of a clamp and a clamping screw. • A shim set for CER/L type consists of a shim and a shim screw.
• Standard shims for CER/L type can be used for both left hand and right hand toolholders. Use either of the sides depending on the hand.
• When using the GTGN insert, the exclusive shim must be used. Exclusive shim should be ordered separately.

SPARE PARTS
Designation Clamp set Clamping screw Shim screw Shim Wrench Wrench 1
(Optional parts)
CER/L123DT, CER/L163DT,
CSP16 CSTB-3.5ST DTS5-3.5 (G16ER/IL-DT) P-3.5 T-15F
CER203DT
CER*****16DT CSP16 CSTB-3.5ST DTS5-3.5 (G16ER/IL-DT) P-3.5 T-15F
CEL*****16DT CSP16 CSTB-3.5ST DTS5-3.5 (G16EL/IR-DT) P-3.5 T-15F
CER3232P16T CSP16 - - (G16ER/IR-S) - T-15F

External
B -S /C E R /L
E x te r n a l t h re ad i ng to o l ho l d er s f o r sw i ss l a t h e s

10°
b

L2 h1
L1
h

Right hand (R) shown.

Others
Metric h b L1 L2 h1 f Insert
B-CER/L16M16 32 16 150 24 16 22 GTGN16...
• When using the GTGN insert, the exclusive shim must be used. Exclusive shim should be ordered separately.

SPARE PARTS
Designation Clamp set Clamping screw Wrench Shim
(Optional parts)
B-CER16M16 CSP16 - T-15F (G16ER/IL-S)
B-CEL16M16 CSP16 - T-15F (G16EL/IR-S)

Reference pages
Inserts → C045, Standard cutting conditions → C046

C044 www.tungaloyamerica.com
CN R

Grooving Tool
I n te r n a l g ro o v i n g b ar s, al ter nat i v e cl am p i ng of s c re w - on or c l a m p - on (DT t y p e on l y )

Carbide reinforcement (for TCNR**)

L1 øDsg7
θº
øDm L2 R3 h

b
f
Right hand (R) shown.

Inch Material øDm øDs f L1 L2 ℓ3 h b θ° Insert

S12-CNR3DT STEEL 0.950 0.750 0.552 7.000 1.200 - 0.725 0.738 15 GTGN-16...
S16-CNR3DT STEEL 1.150 1.000 0.652 8.000 1.500 - 0.906 0.953 15 GTGN-16...
S20-CNR3DT STEEL 1.450 1.250 0.788 10.000 1.900 - 1.188 1.219 15 GTGN-16...
• Shim is used for both right and left hand toolholders.
• A clamp set for CNR/L type toolholders consists of a clamp and a clamping screw. • A shim set for CNR/L type toolholders consists of a shim and a shim fixing screw.
• Standard shims for CNR/L type toolholders are commonly used for right and left hand toolholders.
• When using the GTGN insert, the exclusive shim must be used. Exclusive shim should be ordered separately.

SPARE PARTS
Designation Clamp set Clamping screw Shim screw Shim Wrench Wrench 1
(Optional parts)
S**-CNR3DT CSP16 CSTB-3.5ST DTS5-3.5 (G16EL/IR-DT) P-3.5 T-15F

INSERT
GTG N 16
C
rε W
G

ød
Right hand (R) shown.
Internal
Shim

W±0.03 W±0.001 rε Insert ød G C Dual method clamp

Designation SH730 type; Screw-on/ Clamp-on type
(mm) (in) (in) size (in) (in) (in) Clamp-on
GTGN-16ER/IL100 1 0.039 0.004 䖃 16 0.375 0.049 0.166 G16ER/IL-DT G16ER/IL-S
GTGN-16ER/IL120 1.2 0.047 0.004 䖃 16 0.375 0.051 0.162 G16ER/IL-DT G16ER/IL-S
GTGN-16ER/IL140 1.4 0.055 0.004 䖃 16 0.375 0.059 0.158 G16ER/IL-DT G16ER/IL-S
GTGN-16ER/IL170 1.7 0.067 0.004 䖃 16 0.375 0.067 0.152 G16ER/IL-DT G16ER/IL-S
GTGN-16ER/IL195 1.95 0.077 0.004 䖃 16 0.375 0.067 0.148 G16ER/IL-DT G16ER/IL-S
Others
GTGN-16ER/IL225 2.25 0.089 0.004 䖃 16 0.375 0.071 0.142 G16ER/IL-DT G16ER/IL-S
GTGN-16EL/IR100 1 0.039 0.004 䖃 16 0.375 0.049 0.166 G16EL/IR-DT G16EL/IR-S
GTGN-16EL/IR120 1.2 0.047 0.004 䖃 16 0.375 0.051 0.162 G16EL/IR-DT G16EL/IR-S
GTGN-16EL/IR140 1.4 0.055 0.004 䖃 16 0.375 0.059 0.158 G16EL/IR-DT G16EL/IR-S
GTGN-16EL/IR170 1.7 0.067 0.004 䖃 16 0.375 0.067 0.152 G16EL/IR-DT G16EL/IR-S
GTGN-16EL/IR195 1.95 0.077 0.004 䖃 16 0.375 0.067 0.148 G16EL/IR-DT G16EL/IR-S
GTGN-16EL/IR225 2.25 0.089 0.004 䖃 16 0.375 0.071 0.142 G16EL/IR-DT G16EL/IR-S
Note: Package quantity = 10 pcs
GTGN insert is applicable for both external and internal grooving, but the hand of tool is opposite in external and internal machining.
Shim for GTGN is exclusive to each type of toolholders 䖃 : Line up

Reference pages
Standard cutting conditions → C046

Tungaloy C045
 STAN DARD CUT T ING CONDIT IO N S

Cutting speed Feed

Grooving Tool
ISO Workpiece material Grade
Vc (sfm) f (ipr)
Steels
SH730 160 - 490 0.002 - 0.004
1045, 4140, etc.

Stainless steels
SH730 100 - 490 0.002 - 0.004
304, 316, etc.
Heat-resistant alloys, Titanium alloys etc.
SH730 100 - 330 0.002 - 0.004
Ti-6Al-4V, etc.

C046 www.tungaloyamerica.com
 - Application Guide

Grooving Tool
Multi-purpose grooving line with
economical insert containing 4 cutting
edges

External
1

Parting-off

Others

1 STCR/L -27 2 STCR/L -18 3 JS-STCR/L18

W = 0.020" - 0.125" W = 0.013" - 0.118" W = 0.013" - 0.118"
(0.5 - 3.18 mm) (0.33 - 3 mm) (0.33 - 3 mm)
ar = 0.039" - 0.252" ar = 0.031" - 0.098" ar = 0.031" - 0.098"
(1.0 - 6.4 mm) (0.8 - 2.5 mm) (0.8 - 2.5 mm)
Shank size: Shank size: Shank size:
0.375" - 1.000" (10 - 25 mm) 0.375" - 1.000" (10 - 25 mm) 0.551" - 1.000" (14 - 25.4 mm)
Page C048 Page C055 Page C056
STCR/L -27-CHP JS-STCR/L27
W = 0.020" - 0.125" W = 0.020" - 0.125"
(0.5 - 3.18 mm) (0.5 - 3.18 mm)
ar = 0.039" - 0.252" ar = 0.039" - 0.252"
(1.0 - 6.4 mm) (1.0 - 6.4 mm)
Shank size: 1.000" (25 mm) Shank size:
0.750" - 1.000" (19.05 - 25.4 mm)
Page C048
Page C049

Tungaloy C047
 Grooving Tool STC R /L-27
Pre c i s i o n ex te r n a l g ro o v i n g to o l s w i t h u n i q u e l y s h a p e d i n s e r t w i t h 4 c u t t i n g e d g e s

b
f
W L1
0.906 0.276

h1

h
0.118

h2
L2
Right hand (R) shown.

Inch W h1 b h L1 f h2 L2 Insert
STCR/L06-27 0.020 - 0.125 0.375 0.375 0.375 5.000 0.315 0.374 0.945 TC*27...
STCR/L08-27 0.020 - 0.125 0.500 0.500 0.500 5.000 0.440 0.287 0.945 TC*27...
STCR/L10-27 0.020 - 0.125 0.625 0.625 0.625 5.000 0.570 0.236 0.945 TC*27...
STCR/L12-27 0.020 - 0.125 0.750 0.750 0.750 5.000 0.690 0.118 0.945 TC*27...
STCR/L16-27 0.020 - 0.125 1.000 1.000 1.000 5.500 0.940 - - TC*27...

SPARE PARTS
Designation Screw Wrench
STCR... SR16-212-01397L T-2010/5
STCL... SR16-212-01397 T-2010/5

STC R /L-C H P
Pre c i s i o n ex te r nal g ro o v i ng to o l s w i t h uni q u e l y s h a p e d i n s e r t , w i t h c h a n n e l s f or h i gh p re s s u re c o o lant.
W

b
f

Coolant outlet
L1
0.906 0.335
h1

h
External
0.74 Coolant inlet Right hand (R) shown.

Inch W h1 b h L1 f Insert
STCR/L16-27-CHP 0.020 - 0.125 1.000 1.000 1.000 5.500 0.940 TC*27...

SPARE PARTS
Designation Screw Wrench
STCR...-27-CHP SR16-212-01397L T-2010/5
STCL...-27-CHP SR16-212-01397 T-2010/5

Parting-off

Others

Reference pages
Inserts → C050 - C053, Standard cutting conditions → C054

C048 www.tungaloyamerica.com
J S -STC R /L27

Grooving Tool
Pre c i s i o n g ro o v i n g to o l s w i t h u n i q u e l y s h a p e d i n s e r t f o r s w i s s l a t h e s

L1
L2
W øDs

h
B
Left hand (L) shown.

Inch W øDs L1 L2 h B f Insert

JS19X-STCR/L27 0.020 - 0.125 0.750 4.724 0.787 0.551 0.787 0.394 TC*27...
JS254X-STCR/L27 0.020 - 0.125 1.000 4.724 0.787 0.945 0.787 0.394 TC*27...

SPARE PARTS
Designation Screw Wrench
JS****-STCR27 SR16-212-01397 T-2010/5
JS****-STCL27 SR16-212-01397L T-2010/5

External

Others

Reference pages
Inserts → C050 - C053, Standard cutting conditions → C054

Tungaloy C049
 INSERT - FOR GROOVING A ND PA RTING OFF
Grooving Tool TC S27
rε 0.157 øD max

W
T max

ø1.063

0.118

W ± 0.02 W ± 0.001 rε T max øD max Relation of groove depth (T) and Max. diameter øD max (in)
Designation AH725
(mm) (in) (in) (in) (in) T≤1 T≤2 T≤3 T≤3.5 T≤4 T≤4.5 T≤5 T≤5.5 T≤5.7 T≤6 T≤6.2 T≤6.4

TCS27-050-000 0.5 0.020 0.000 䖃 0.039 0.079 ∞ - - - - - - - - - - -

TCS27-050-004 0.5 0.020 0.0016 䖃 0.098 0.197 ∞ ∞ - - - - - - - - - -

TCS27-075-010 0.75 0.030 0.004 䖃 0.098 0.197 ∞ ∞ - - - - - - - - - -

TCS27-080-000 0.8 0.031 0.000 䖃 0.063 0.126 ∞ - - - - - - - - - - -

TCS27-100-006 1 0.039 0.0024 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-100-010 1 0.039 0.004 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-104-000 1.04 0.041 0.000 䖃 0.079 0.158 ∞ ∞ - - - - - - - - - -

TCS27-120-000 1.2 0.047 0.000 䖃 0.079 0.158 ∞ ∞ - - - - - - - - - -

TCS27-125-010 1.25 0.049 0.004 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-125-020 1.25 0.049 0.008 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-140-000 1.4 0.055 0.000 䖃 0.079 0.158 ∞ ∞ - - - - - - - - - -

TCS27-147-000 1.47 0.058 0.000 䖃 0.098 0.197 ∞ ∞ - - - - - - - - - -

TCS27-150-010 1.5 0.059 0.004 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-150-020 1.5 0.059 0.008 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-157-015 1.57 0.062 0.006 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-170-010 1.7 0.067 0.004 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-175-010 1.75 0.069 0.004 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-175-020 1.75 0.069 0.008 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-178-018 1.78 0.070 0.007 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-185-020 1.85 0.073 0.008 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-196-015 1.96 0.077 0.006 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCS27-200-010 2 0.079 0.004 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 4.134 3.346 2.362 1.969 1.181
TCS27-200-020 2 0.079 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 4.134 3.346 2.362 1.969 1.181
TCS27-222-015 2.22 0.087 0.006 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-230-020 2.3 0.091 0.008 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCS27-239-015 2.39 0.094 0.006 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-247-020 2.47 0.097 0.008 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-250-010 2.5 0.098 0.004 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-250-030 2.5 0.098 0.012 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCS27-270-010 2.7 0.106 0.004 䖃 0.244 0.488 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 -

TCS27-287-020 2.87 0.113 0.008 䖃 0.244 0.488 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 -

TCS27-300-000 3 0.118 0.000 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.165
TCS27-300-020 3 0.118 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.165
TCS27-300-030 3 0.118 0.012 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.165
TCS27-300-040 3 0.118 0.016 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.165
TCS27-315-015 3.15 0.124 0.006 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.677
TCS27-318-020 3.18 0.125 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.677

Package Quantity = 5 pcs.

䖃 : Line up

C050 www.tungaloyamerica.com
 INSERT - FOR PA RTING OFF
TC S 27-R /L

Grooving Tool
rε 0.157
øD max øD max

W
θ° T max

ø1.063 0.118 0.118

Right hand (R) shown.

W ± 0.02 W ± 0.001 rε AH725 T max Max. parting off dia. øD max (in)
Designation θ°
(mm) (in) (in) R L (in) Solid bar Tube
TCS27-100-15R/L 1 0.039 0.0024 䖃 䖃 0.138 15 0.276 23.622

TCS27-150-6R/L 1.5 0.059 0.0024 䖃 䖃 0.224 6 0.449 1.378

TCS27-150-15R/L 1.5 0.059 0.0024 䖃 䖃 0.224 15 0.449 1.378

TCS27-200-6R/L 2 0.079 0.004 䖃 䖃 0.252 6 0.504 1.181

TCS27-200-15R/L 2 0.079 0.004 䖃 䖃 0.252 15 0.504 1.181

Package Quantity = 5 pcs.

䖃 : Line up

INSERT - FOR GROOVING A ND PROFILING

TC S 27-Ful l R
rε
4

øD max
W

T max

ø27

0.118

W ± 0.02 W ± 0.001 rε T max Relation of groove depth (T) and Max. diameter øD max (in)
Designation AH725
(mm) (in) (in) (in) T ) 0.039 T ) 0.079 T ) 0.118 T ) 0.138 T ) 0.158 T ) 0.177 T ) 0.197 T ) 0.217 T ) 0.224 T ) 0.236 T ) 0.244 T ) 0.252

TCS27-157-079 1.57 0.062 0.031 䖃 0.118 ∞ ∞ ∞ - - - - - - - - -

TCS27-200-100 2 0.079 0.039 䖃 0.118 ∞ ∞ ∞ - - - - - - - - -

TCS27-239-120 2.39 0.094 0.047 䖃 0.224 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -
TCS27-300-150 3 0.118 0.059 䖃 0.252 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.740 3.346 3.071 2.165

Package Quantity = 5 pcs.

䖃 : Line up

Tungaloy C051
 INSERT - FOR GROOVING A ND PA RTING OFF
Grooving Tool TC M 27
rε 0.157
øD max
T max

W
ø1.063
0.118

W ± 0.02 W ± 0.001 rε T max øD max Relation of groove depth (T) and Max. diameter øD max (in)
Designation AH725
(mm) (in) (in) (in) (in) T≤0.039 T≤0.078 T≤0.118 T≤0.138 T≤0.157 T≤0.177 T≤0.197 T≤0.217 T≤0.224 T≤0.236 T≤0.244 T≤0.252

TCM27-150-010 1.5 0.059 0.004 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-150-020 1.5 0.059 0.008 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-157-015 1.57 0.062 0.006 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-170-010 1.7 0.067 0.004 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-175-010 1.75 0.069 0.004 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-175-020 1.75 0.069 0.008 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-178-018 1.78 0.07 0.007 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-185-020 1.85 0.073 0.008 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-196-015 1.96 0.077 0.006 䖃 0.118 0.236 ∞ ∞ ∞ - - - - - - - - -

TCM27-200-010 2 0.079 0.004 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 4.134 3.346 2.362 1.969 1.181

TCM27-200-020 2 0.079 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 4.134 3.346 2.362 1.969 1.181

TCM27-222-015 2.22 0.087 0.006 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCM27-230-020 2.3 0.091 0.008 䖃 0.138 0.276 ∞ ∞ ∞ 23.622 - - - - - - - -

TCM27-239-015 2.39 0.094 0.006 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-247-020 2.47 0.097 0.008 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-250-010 2.5 0.098 0.004 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-250-030 2.5 0.098 0.012 䖃 0.224 0.449 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-270-010 2.7 0.106 0.004 䖃 0.244 0.488 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 -

TCM27-287-020 2.87 0.113 0.008 䖃 0.244 0.488 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 -

TCM27-300-000 3 0.118 0 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.165

TCM27-300-020 3 0.118 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.165

TCM27-300-030 3 0.118 0.012 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.165

TCM27-300-040 3 0.118 0.016 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.165

TCM27-315-015 3.15 0.124 0.006 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.677

TCM27-318-020 3.18 0.125 0.008 䖃 0.252 0.504 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.677

Package Quantity = 5 pcs.

䖃 : Line up

C052 www.tungaloyamerica.com
 INSERT - FOR GROOVING A ND PROFILING
TC M 27-Ful l R

Grooving Tool
rε 0.157 øD max

T max
W

ø1.063
0.118

W ± 0.02 W ± 0.001 rε T max Relation of groove depth (T) and Max. diameter øD max (in)
Designation AH725
(mm) (in) (in) (in) T≤0.039 T≤0.078 T≤0.118 T≤0.138 T≤0.157 T≤0.177 T≤0.197 T≤0.217 T≤0.224 T≤0.236 T≤0.244 T≤0.252
TCM27-157-079 1.57 0.062 0.031 䖃 0.118 ∞ ∞ ∞ - - - - - - - - -

TCM27-200-100 2 0.079 0.039 䖃 0.118 ∞ ∞ ∞ - - - - - - - - -

TCM27-239-120 2.39 0.094 0.047 䖃 0.224 ∞ ∞ ∞ 23.622 11.024 7.087 5.118 1.969 1.378 - - -

TCM27-300-150 3 0.118 0.059 䖃 0.252 ∞ ∞ ∞ 23.622 11.024 7.087 5.315 4.134 3.74 3.346 3.071 2.165

Package Quantity = 5 pcs.

䖃 : Line up

C H IPB R E A K E R

TCS27
W = 0.020" - 0.125"
(0.5 mm - 3.18 mm)
For general machining
Lower cutting force and superior sharpness

TCM27
W = 0.059" - 0.125"
(1.5 mm - 3.18 mm)
For high feed machining
Well-designed edge with high strength

Tungaloy C053
 STAN DARD CUT T ING CONDIT IO N S

Feed: f (ipr)
Grooving Tool
Cutting Depth of cut
speed Grooving, Parting-off Profiling for profiling
ISO Workpiece material Grade
Vc parting-off (with hand) (with full radius insert) (with full
(sfm) radius insert)
TCS TCM TCS TCS TCM
Steel
AH725 330 - 660 0.002 - 0.006 0.002 - 0.01 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(1045, etc.)
Alloy steel
AH725 165 - 590 0.002 - 0.006 0.002 - 0.01 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(4137, etc.)
Stainless steel
AH725 165 - 490 0.002 - 0.006 0.002 - 0.008 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(304, etc.)
Gray cast iron
AH725 165 - 590 0.002 - 0.006 0.002 - 0.01 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(No.250, etc.)
Ductile cast iron
AH725 165 - 390 0.002 - 0.006 0.002 - 0.008 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(60-40-18, etc.)
Titanium alloys
AH725 100 - 200 0.002 - 0.006 0.002 - 0.006 0.002 - 0.005 0.002 - 0.004 0.002 - 0.006 0.02
(Ti-6AI-4V, etc.)

PARTS FOR COOLANT HOSE

Connecting hose
Fig. 1 Th Th1 Fig. 2 Th1
L Th
L

Length Threading size Max. pressure

Metric Fig.
L Th Th1 (MPa)
CHP-HOSE-G1/8-7/16-200BS 200 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-G1/8-7/16-250BS 250 G1/8"-28 BSPP 7/16"-20 UNF 26 1
CHP-HOSE-G1/8-G1/8-200BB 200 G1/8"-28 BSPP G1/8"-28 BSPP 26 2
CHP-HOSE-G1/8-G1/8-250BB 250 G1/8"-28 BSPP G1/8"-28 BSPP 26 2

Connector Seal washer

HEX9/16”
7/16”-20 UNF 1/8”-28 BSPP
4.0

ød
øD
13.8

37°

14 7.1
W
28.75

Metric Metric øD ød W
CHP-NIPPLE-G1/8-7/16UNF CHP-COPPER-SEAL1/8 15 10 1

C054 www.tungaloyamerica.com
STC R /L-18

Grooving Tool
Pre c i s i o n ex te r n a l g ro o v i ng and t hread i ng to ol s w i t h u n i q u e l y s h a p e d i n s e r t f or s w i s s l a t h e s

L1
L2

0.256"
h1

h
h2

b
f
Right hand (R) shown.

Inch h b L1 L2 h1 f h2 Insert
STCR/L06-18 0.375 0.375 4.750 0.740 0.375 0.375 0.177 TC*18...
STCR/L08-18 0.500 0.500 4.750 0.740 0.500 0.500 0.098 TC*18...
STCR/L10-18 0.625 0.625 4.750 0.740 0.625 0.625 - TC*18...
STCR/L12-18 0.750 0.750 4.750 0.900 0.750 1.000 - TC*18...
STCR/L16-18 1.000 1.000 5.500 0.900 1.000 1.250 - TC*18...

• The right hand insert (TC*18R***) is used for the right hand toolholders (STCR***), and the left hand insert (TC*18L***) is used for the left hand toolholders (STCL***).

SPARE PARTS
Designation Clamping screw Wrench
STCR*****18 CSTC-4L100DL T-1008/5
STCL*****18 CSTC-4L100DR T-1008/5

External

Others

Reference pages
Inserts → C056 - C058, Standard cutting conditions → C057 - C058

Tungaloy C055
 Grooving Tool JS -STC R /L18
Pre c i s i o n g ro o v i n g to o l s w i t h u n i q u e l y s h a p e d i n s e r t f o r s w i s s l a t h e s

L1
L2 øDs

h
B
94°

Left hand (L) shown.

Metric øDs L1 L2 h B f Insert

JS14H-STCL18 14 100 20 13 14 6 TC*18...
JS159F-STCL18 15.875 (0.675") 85 20 15 14 6 TC*18...
JS16F-STCL18 16 85 20 15 14 6 TC*18...
JS19G-STCR/L18 19.05 (0.750") 90 20 18 14 6 TC*18...
JS19X-STCL18 19.05 (0.750") 120 20 18 14 6 TC*18...
JS20G-STCL18 20 90 20 19 14 6 TC*18...
JS20X-STCL18 20 120 20 19 14 6 TC*18...
JS22X-STCL18 22 120 20 21 12.25 10 TC*18...
JS25H-STCL18 25 100 20 24 12.25 10 TC*18...
JS254G-STCR18 25.4 (1.00") 90 20 24 12.25 10 TC*18...
JS254X-STCL18 25.4 (1.00") 120 20 24 12.25 10 TC*18...
• The right hand insert (TC*18R***) is used for the left hand toolholders (STCL***), and the left hand insert (TC*18L***) is used for the right hand toolholders (STCR***).

SPARE PARTS
Designation Clamping screw Wrench
JS****-STCR18 CSTC-4L100DR T-1008/5
JS****-STCL18 CSTC-4L100DL T-1008/5

INSERT
TC P18R /L-F (s harp ed g e)
W
External
rε
G

T
ød
W±0.02 W±0.001 rε SH725 G T ød
Designation
(mm) (in) (in) R L (in) (in) (in)

TCP18R/L033F-005 0.33 0.013 0.002 䖃 䖃 0.031 0.157 0.709

TCP18R/L043F-005 0.43 0.017 0.002 䖃 䖃 0.047 0.157 0.709
TCP18R/L050F-005 0.5 0.020 0.002 䖃 䖃 0.047 0.157 0.709
Others TCP18R/L075F-005 0.75 0.030 0.002 䖃 䖃 0.079 0.157 0.709
TCP18R/L095F-005 0.95 0.037 0.002 䖃 䖃 0.047 0.157 0.709
TCP18R/L100F-010 1 0.039 0.004 䖃 䖃 0.079 0.157 0.709
TCP18R/L120F-010 1.2 0.047 0.004 䖃 䖃 0.047 0.157 0.709
TCP18R/L125F-010 1.25 0.049 0.004 䖃 䖃 0.079 0.157 0.709
TCP18R/L145F-010 1.45 0.057 0.004 䖃 䖃 0.047 0.157 0.709
TCP18R/L150F-010 1.5 0.059 0.004 䖃 䖃 0.079 0.157 0.709
TCP18R/L175F-010 1.75 0.069 0.004 䖃 䖃 0.047 0.157 0.709
TCP18R/L200F-010 2 0.079 0.004 䖃 䖃 0.098 0.157 0.709
TCP18R/L250F-010 2.5 0.098 0.004 䖃 䖃 0.098 0.157 0.709
TCP18R/L300F-010 3 0.118 0.004 䖃 䖃 0.098 0.157 0.709

䖃 : Line up

Reference pages
Inserts → C056 - C058, Standard cutting conditions → C057 - C058

C056 www.tungaloyamerica.com
TC P18R /L( honed ed g e)

Grooving Tool
rε

G
T
ød

W±0.02 W±0.001 rε AH725 G T ød

Designation
(mm) (in) (in) R L (in) (in) (in)

TCP18R/L033-005 0.33 0.013 0.002 䖃 䖃 0.031 0.157 0.709

TCP18R/L043-005 0.43 0.017 0.002 䖃 䖃 0.047 0.157 0.709

TCP18R/L050-005 0.5 0.020 0.002 䖃 䖃 0.047 0.157 0.709

TCP18R/L075-005 0.75 0.030 0.002 䖃 䖃 0.079 0.157 0.709

TCP18R/L095-005 0.95 0.037 0.002 䖃 䖃 0.079 0.157 0.709

TCP18R/L100-010 1 0.039 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L120-010 1.2 0.047 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L125-010 1.25 0.049 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L145-010 1.45 0.057 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L150-010 1.5 0.059 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L175-010 1.75 0.069 0.004 䖃 䖃 0.079 0.157 0.709

TCP18R/L200-010 2 0.079 0.004 䖃 䖃 0.098 0.157 0.709

TCP18R/L250-010 2.5 0.098 0.004 䖃 䖃 0.098 0.157 0.709

TCP18R/L300-010 3 0.118 0.004 䖃 䖃 0.098 0.157 0.709

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS

Cutting speed Feed
ISO Workpiece material Priority Grade f (ipr)
Vc (sfm)
Low carbon steels First choice SH725 260 - 590 0.001 - 0.004
(1015, etc.) Toughness AH725 260 - 590 0.001 - 0.004
Carbon steels, Alloy steels First choice SH725 260 - 590 0.001 - 0.004
(1055, etc.) Toughness AH725 260 - 590 0.001 - 0.004
Prehardened steels First choice SH725 260 - 590 0.001 - 0.004
(NAK80, PX5 etc.) Toughness AH725 260 - 590 0.001 - 0.004
Stainless steels First choice SH725 160 - 394 0.001 - 0.004
(S30400, etc) Toughness AH725 160 - 394 0.001 - 0.004
Grey cast irons First choice AH725 160 - 590 0.001 - 0.004
(No.250B, No.300B etc.) Sharpness SH725 160 - 590 0.001 - 0.004
Ductile cast irons First choice AH725 160 - 590 0.001 - 0.004
(60-40-18, 80-55-06, etc.) Sharpness SH725 160 - 590 0.001 - 0.004
First choice SH725 60 - 260 0.001 - 0.004
Titanium alloys (Ti-6AI-4V, etc.)
Toughness AH725 60 - 260 0.001 - 0.004
First choice SH725 60 - 260 0.001 - 0.004
Superalloys (Inconel718, etc.)
Toughness AH725 60 - 260 0.001 - 0.004

C H I PB R EA K ER

TCP18
W = 0.013" - 0.118"
(0.33 mm - 3 mm)
Suitable for small parts on swiss lathe
Low cutting force with large rake angle

Tungaloy C057
 INSERT
Grooving Tool TCT18R /L ( Fo r T hread i ng )
T

S
rε f
ød
θ°
rε AH725 Pitch Pitch f S T ød
Designation min max θ°
(in) R L (in) (in) (in) (in) (in) (in)
0.031 0.118
TCT18R/L-60N-010 0.004 䖃 䖃 0.063 0.105 60 0.157 0.709
(0.8 mm) (3 mm)
0.059 0.118
TCT18R/L-60N-020 0.008 䖃 䖃 0.063 0.101 60 0.157 0.709
(1.5 mm) (3 mm)
䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S

Cutting speed
ISO Workpiece material Grade Pitch (in) TPI
Vc (sfm)
Low carbon steels AH725 190 - 490 0.031 - 0.118 32 -8
(1015, etc.)
Carbon steels, Alloy steels AH725 190 - 490 0.031 - 0.118 32 -8
(1055, etc.)
Prehardened steels AH725 190 - 490 0.031 - 0.118 32 -8
(NAK80, PX5 etc.)
Stainless steels
(S30400, etc) AH725 160 - 260 0.031 - 0.118 32 -8

Grey cast irons

(No.250B, No.300B etc.) AH725 160 - 320 0.031 - 0.118 32 -8

Ductile cast irons

(60-40-18, 80-55-06, etc.) AH725 160 - 320 0.031 - 0.118 32 -8

Titanium alloys (Ti-6AI-4V, etc.) AH725 90 - 320 0.031 - 0.118 32 -8

Superalloys (Inconel718, etc.) AH725 90 - 320 0.031 - 0.118 32 -8

C058 www.tungaloyamerica.com
 - Application Guide

Grooving Tool
Multi-functional tool reduces tool cost
and shortens set-up time
2
1 2

4
5

6 12

11

7
10 13
9
8
External

1 CGEUR/L 2 CTEFR/L 3 CTFR/L 4 CTIR/L 5 CTIFR/L Internal

Monoblock type Monoblock type Monoblock type Monoblock type Monoblock type
W = 0.118" - 0.236" W = 0.157" - 0.236" W = 0.118" - 0.236" W = 0.079" - 0.315" W = 0.118" - 0.236"
(3 - 6 mm) (2 - 6 mm) (3 - 6 mm) (2 - 8 mm) (3 - 6 mm)
ar = 0.110" - 0.314" ar = 0.189" ar = 10 - 25 mm ar = 0.157" - 0.394" ar = 0.217" (5.5 mm) Face
(2.8 - 3.4 mm) (4.8 mm) Shank size: 25 mm (4 - 10 mm) Shank size: Grooving

Shank size: 16 - 25 mm Shank size: 0.75" - 1.00" Page C072 Shank size: 1.000" - 1.250"
Page C069 (20 - 25 mm) 0.750" - 1.500" (25 - 32 mm)
Page C063 (16 - 40 mm) Page C077
Page C070 Parting-off

6 CGIUR/L 7 CTFVR/L 8 CAFR/L 9 CTER/L 10 CAER/L Others

Monoblock type Monoblock type Adaptor type Monoblock type Adaptor type
W = 0.118" - 0.236" W = 3 - 6 mm W = 0.118" - 0.236" W = 0.079" - 0.315" W = 0.118" - 0.236"
(3 - 6 mm) ar = 10 - 20 mm (3 - 6 mm) (2 - 8 mm) (3 - 6 mm)
ar = 0.110" (2.8 mm) Shank size: 25 mm ar = 0.472" - 0.984" ar = 0.315" - 1.417" ar = 0.630" - 0.787"
Shank size: 20 - 25 mm Page C073 (12 - 25 mm) (8 - 36 mm) (16 - 20 mm)
Page C071 Shank size: Shank size: Shank size:
0.75" - 1.25" 0.625" - 1.250" 0.75" - 1.25"
(20 - 32 mm) (16 - 32 mm) (20 - 32 mm)
Page C074 Page C060 Page C064
11 CGP 12 CGER/L 13 JCTER/L
Blade type Monoblock type Monoblock type
W = 0.055" - 0.315" W = 0.055" - 0.157" W = 0.055" - 0.118"
(1.4 - 8 mm) (1.4 - 4 mm) (1.4 - 3 mm)
Max. parting Dia.: ar = 0.382" - 0.799" ar = 0.50" - 0.625"
4.724" (ø120 mm) (9.7 - 20.3 mm) (10 - 16 mm)
Shank size: Shank size: 12 - 20 mm Shank size:
1.000" - 1.26" Page C063 0.500" - 0.625"
(20 - 25 mm) (10 - 20 mm)
Page C067 Page C062

Tungaloy C059
 Grooving Tool CTER /L
E x te r n a l to o l h o l d e r s f o r g ro o v i n g , p a r t i n g & t u r n i n g

b
ar

w
f
L1
L2 Insert:
DGM, SGM, DGS,

h1
SGS, DGG, DTX,

h
DTE, DTR, DTA, SGN

h2
Right hand (R) shown.

Inch W (in) W (mm) Seat size ar h b L1 L2 h1 f (1) h2

CTER/L10-2T08 0.079 2 2 0.315 0.625 0.625 4.500 1.299 0.625 0.629 0.157
CTER/L12-2T08 0.079 2 2 0.315 0.750 0.750 5.000 1.299 0.750 0.754 -
CTER/L16-2T08 0.079 2 2 0.315 1.000 1.000 6.000 1.299 1.000 1.004 -
CTER/L10-2T12 0.079 2 2 0.472 0.625 0.625 4.500 1.260 0.625 0.629 0.157
CTER/L12-2T12 0.079 2 2 0.472 0.750 0.750 5.000 1.260 0.750 0.754 -
CTER/L16-2T12 0.079 2 2 0.472 1.000 1.000 6.000 1.260 1.000 1.004 -
CTER/L10-2T17 0.079 2 2 0.669 0.625 0.625 4.500 1.457 0.625 0.629 0.157
CTER/L12-2T17 0.079 2 2 0.669 0.750 0.750 5.000 1.457 0.750 0.754 -
CTER/L16-2T17 0.079 2 2 0.669 1.000 1.000 6.000 1.457 1.000 1.024 -
CTER/L10-3T09 0.118 3 3 0.354 0.625 0.625 4.500 1.260 0.625 0.637 0.157
CTER/L12-3T09 0.118 3 3 0.354 0.750 0.750 5.000 1.260 0.750 0.762 -
CTER/L16-3T09 0.118 3 3 0.354 1.000 1.000 6.000 1.260 1.000 1.012 -
CTER/L12-3T12 0.118 3 3 0.472 0.750 0.750 5.000 1.260 0.750 0.763 -
CTER/L16-3T12 0.118 3 3 0.472 1.000 1.000 6.000 1.260 1.000 1.012 -
CTER/L10-3T20 0.118 3 3 0.787 0.625 0.625 4.500 1.516 0.625 0.637 -
CTER/L12-3T20 0.118 3 3 0.787 0.750 0.750 5.000 1.516 0.750 0.762 -
CTER/L16-3T20 0.118 3 3 0.787 1.000 1.000 6.000 1.516 1.000 1.012 0.157
CTER/L16-3T25 0.118 3 3 0.984 1.000 1.000 6.000 1.752 1.000 1.012 -
CTER/L10-4T10 0.157 4 4 0.394 0.625 0.625 4.500 1.260 0.625 0.645 -
CTER/L12-4T10 0.157 4 4 0.394 0.750 0.750 5.000 1.260 0.750 0.770 -
CTER/L16-4T10 0.157 4 4 0.394 1.000 1.000 6.000 1.260 1.000 1.020 0.157
CTER/L12-4T15 0.157 4 4 0.590 0.750 0.750 5.000 1.299 0.750 0.770 -
External
CTER/L16-4T15 0.157 4 4 0.590 1.000 1.000 6.000 1.299 1.000 1.020 -
CTER/L10-4T25 0.157 4 4 0.984 0.625 0.625 4.500 1.772 0.625 0.645 -
CTER/L12-4T25 0.157 4 4 0.984 0.750 0.750 5.000 1.772 0.750 0.770 -
CTER/L16-4T25 0.157 4 4 0.984 1.000 1.000 6.000 1.772 1.000 1.020 -
CTER/L20-4T25 0.157 4 4 0.984 1.250 1.250 7.000 1.772 1.250 1.270 -
CTER/L12-5T12 0.197 5 5 0.472 0.750 0.750 5.000 1.457 0.750 0.774 0.157
CTER/L16-5T12 0.197 5 5 0.472 1.000 1.000 6.000 1.457 1.000 1.024 -
CTER/L16-5T20 0.197 5 5 0.787 1.000 1.000 6.000 1.457 1.000 1.024 -
CTER/L16-5T32 0.197 5 5 1.260 1.000 1.000 6.000 2.205 1.000 1.024 -
Parting-off CTER/L20-5T32 0.197 5 5 1.260 1.250 1.250 7.000 2.205 1.250 1.274 -
CTER/L12-6T12 0.236 6 6 0.472 0.750 0.750 5.000 1.457 0.750 0.770 -
Others CTER/L16-6T12 0.236 6 6 0.472 1.000 1.000 6.000 1.457 1.000 1.020 -
CTER/L16-6T20 0.236 6 6 0.787 1.000 1.000 6.000 1.614 1.000 1.023 -
CTER/L16-6T32 0.236 6 6 1.260 1.000 1.000 6.000 2.205 1.000 1.020 -
CTER/L20-6T32 0.236 6 6 1.260 1.250 1.250 7.000 2.205 1.250 1.270 -
CTER/L16-8T16 0.315 8 8 0.630 1.000 1.000 6.000 1.850 1.000 1.039 -
CTER/L16-8T25 0.315 8 8 0.984 1.000 1.000 6.000 1.850 1.000 1.039 -
CTER/L20-8T25 0.315 8 8 0.984 1.250 1.250 7.000 1.850 1.250 1.289 0.276
CTER/L16-8T36 0.315 8 8 1.417 1.000 1.000 6.000 2.362 1.000 1.039 -
CTER/L20-8T36 0.315 8 8 1.417 1.250 1.250 7.000 2.362 1.250 1.289 0.276
• When depth is deeper than (insert length - 0.059"), 1 corner type is recommended.
(1) "f" value is calculated with groove width "W" shown in the table.

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C060 www.tungaloyamerica.com
 Metric W Seat size ar h b L1 L2 h1 f (1) h2
CTER/L1616-2T08 2 2 8 16 16 110 33 16 16.1 4
CTER/L2020-2T08 2 2 8 20 20 125 33 20 20.1 -

Grooving Tool
CTER/L2525-2T08 2 2 8 25 25 150 33 25 25.1 -
CTER/L1616-2T12 2 2 12 16 16 110 32 16 16.1 4
CTER/L2020-2T12 2 2 12 20 20 125 32 20 20.1 -
CTER/L2525-2T12 2 2 12 25 25 150 32 25 25.1 -
CTER/L1616-2T17 2 2 17 16 16 110 37 16 16.1 4
CTER/L2020-2T17 2 2 17 20 20 125 37 20 20.1 -
CTER/L2525-2T17 2 2 17 25 25 150 37 25 25.1 -
CTER/L1616-3T09 3 3 9 16 16 110 32 16 16.3 4
CTER/L2020-3T09 3 3 9 20 20 125 32 20 20.3 -
CTER/L2525-3T09 3 3 9 25 25 150 32 25 25.3 -
CTER/L2020-3T12 3 3 12 20 20 125 32 20 20.3 -
CTER/L2525-3T12 3 3 12 25 25 150 32 25 25.3 -
CTER/L1616-3T20 3 3 20 16 16 110 38.5 16 16.3 4
CTER/L2020-3T20 3 3 20 20 20 125 38.5 20 20.3 -
CTER/L2525-3T20 3 3 20 25 25 150 38.5 25 25.3 -
CTER/L2525-3T25 3 3 25 25 25 150 44.5 25 25.3 -
CTER/L1616-4T10 4 4 10 16 16 110 32 16 16.5 4
CTER/L2020-4T10 4 4 10 20 20 125 32 20 20.5 -
CTER/L2525-4T10 4 4 10 25 25 150 32 25 25.5 -
CTER/L2020-4T15 4 4 15 20 20 125 33 20 20.5 -
CTER/L2525-4T15 4 4 15 25 25 150 33 25 25.5 -
CTER/L1616-4T25 4 4 25 16 16 110 45 16 16.5 4
CTER/L2020-4T25 4 4 25 20 20 125 45 20 20.5 -
CTER/L2525-4T25 4 4 25 25 25 150 45 25 25.5 -
CTER/L3232-4T25 4 4 25 32 32 170 45 32 32.5 -
CTER/L2020-5T12 5 5 12 20 20 125 37 20 20.6 -
CTER/L2525-5T12 5 5 12 25 25 150 37 25 25.6 -
CTER/L2525-5T20 5 5 20 25 25 150 37 25 25.6 -
CTER/L2525-5T32 5 5 32 25 25 150 56 25 25.6 -
CTER/L3232-5T32 5 5 32 32 32 170 56 32 32.6 -
CTER/L2020-6T12 6 6 12 20 20 125 37 20 20.6 -
CTER/L2525-6T12 6 6 12 25 25 150 37 25 25.6 7
CTER/L2525-6T20 6 6 20 25 25 150 41 25 25.6 -
CTER/L2525-6T32 6 6 32 25 25 150 56 25 25.6 7
CTER/L3232-6T32 6 6 32 32 32 170 56 32 32.6 -
CTER/L2525-8T16 8 8 16 25 25 150 47 25 26.1 7
CTER/L2525-8T25 8 8 25 25 25 150 47 25 26.1 7
CTER/L3232-8T25 8 8 25 32 32 170 47 32 33.1 -
CTER/L2525-8T36 8 8 36 25 25 150 60 25 26.1 7
CTER/L3232-8T36 8 8 36 32 32 170 60 32 33.1 - External

• When depth is deeper than (insert length - 0.059"), 1 corner type is recommended. (1) "f" value is calculated with groove width "W" shown in the table.

SPARE PARTS SPARE PARTS

Designation Clamping screw Wrench Designation Clamping screw Wrench
CTER/L10-2T08, CTER/L16-4T10,
CTER/L1616-2T08 CM5X0.8X16-A P-4 CM6X1X25-A P-5
CTER/L2525-4T10
CTER/L12-2T08, CTER/L12-4T15,
CTER/L2020-2T08 CM5X0.8X20-A P-4 CM6X1X20-A P-5
CTER/L2020-4T15
CTER/L16-2T08, CTER/L16-4T15,
CTELR/L2525-2T08 CM5X0.8X25-A P-4 CM6X1X25-A P-5
CTER/L2525-4T15
CTER/L10-2T12, CTER/L10-4T25,
CTER/L1616-2T12 CM5X0.8X16-A P-4 CM6X1X16-A P-5
CTER/L1616-4T25
CTER/L12-2T12, CTER/L12-4T25, Parting-off
CTER/L2020-2T12 CM5X0.8X20-A P-4 CM6X1X20-A P-5
CTER/L2020-4T25
CTER/L16-2T12, CTER/L16-4T25,
CTER/L2525-2T12 CM5X0.8X25-A P-4 CM6X1X25-A P-5
CTER/L2525-4T25 Others
CTER/L10-2T17, CTER/L20-4T25,
CTER/L1616-2T17 CM5X0.8X16-A P-4 CM6X1X25-A P-5
CTER/L3232-4T25
CTER/L12-2T17, CTER/L12-5T12,
CTER/L2020-2T17 CM5X0.8X20-A P-4
CTER/L16-5T12, CM6X1X20-A P-5
CTER/L16-2T17, CTER/L2020-5T12
CTER/L2525-2T17 CM5X0.8X25-A P-4
CTER/L16-5T20,
CTER/L2525-5T20 CM6X1X25-A P-5
CTER/L10-3T09,
CTER/L1616-3T09 CM5X0.8X16-A P-4
CTER/L16-5T32,
CTER/L2525, 3232-5T32 CM6X1X25-A P-5
CTER/L12-3T09,
CTER/L2020-3T09 CM5X0.8X20-A P-4
CTER/L20-5T32,
CTER/L2020-6T12 CM8X1.25X20-A P-6
CTER/L12-3T12,
CTER/L2525-3T09 CM5X0.8X25-A P-4
CTER/L12-6T12,
CTER/L16-3T12, CTER/L16-6T12, CM8X1.25X25-A P-6
CTER/L2020-3T12 CM5X0.8X20-A P-4 CTER/L2525-6T12
CTER/L10-3T20, CTER/L16-6T20,
CM5X0.8X25-A P-4 CTER/L2525-6T20 CM8X1.25X25-A P-6
CTER/L2525-3T12
CTER/L12-3T20, CTER/L16-6T32,
CTER/L1616-3T20 CM5X0.8X16-A P-4 CTER/L20-6T32, CM8X1.25X25-A P-6
CTER/L2525, 3232-6T32
CTER/L16-3T20,
CTER/L2020-3T20 CM5X0.8X20-A P-4 CTER/L16-8T16,
CTER/L2525-8T16 CM8X1.25X25-A P-6
CTER/L16-3T25,
CTER/L2525-3T20.25 CM5X0.8X25-A P-4 CTER/L16-8T25,
CTER/L10-4T10,
CTER/L20-8T25, CM8X1.25X25-A P-6
CM6X1X16-A P-5 CTER/L2525, 3232-8T25
CTER/L1616-4T10
CTER/L16-8T36,
CTER/L12-4T10, CTER/L20-8T36, CM8X1.25X25-A P-6
CTER/L2020-4T10 CM6X1X20-A P-5
CTER/L2525, 3232-8T36

Tungaloy C061
 Grooving Tool JCTER /L
E x te r n a l g ro o v i n g & p a r t i n g to o l h o l d e r s f o r s w i s s l a t h e s

b
f
L1 Insert:

øDmax L2 Seat size 1 = DGS1.4-016

Seat size 2, 3, = DGM, SGM,

h2
DGS, SGS, DGE, DTE, DGG

h1

h
Right hand (R) shown.

Inch W Seat size øDmax h b L1 L2 h1 f (1) h2

JCTER/L08-2T12 0.079 1 0.945 0.500 0.500 4.750 0.748 0.500 0.504 0.079
JCTER/L08-3T12 0.118 1 0.945 0.500 0.500 4.750 0.748 0.500 0.512 0.079
JCTER/L10-2T16 0.079 1 1.260 0.625 0.625 4.750 0.945 0.625 0.629 -
JCTER/L10-3T16 0.118 1 1.260 0.625 0.625 4.750 0.945 0.625 0.637 -

Metric W Seat size øDmax h b L1 L2 h1 f (1) h2

JCTER/L1010X1.4T10 1.4 1 20 10 10 120 18 10 10.2 -
JCTER/L1010-1.4T10 1.4 1 20 10 10 125 18 10 10.2 -
JCTER/L1212F1.4T12 1.4 1 24 12 12 85 19.5 12 12.2 -
JCTER/L1212X1.4T12 1.4 1 24 12 12 120 19.5 12 12.2 -
JCTER/L1212-1.4T12 1.4 1 24 12 12 125 19.5 12 12.2 -
JCTER/L1414-1.4T12 1.4 1 24 14 14 125 19.5 14 14.2 -
JCTER/L1616X1.4T16 1.4 1 32 16 16 120 24 16 16.2 -
JCTER/L1616-1.4T16 1.4 1 32 16 16 125 24 16. 16.2 -
JCTER/L1010X2T10 2 2 20 10 10 120 19 10 10.1 2
JCTER/L1010-2T10 2 2 20 10 10 125 19 10 10.1 2
JCTER/L1212F2T12 2 2 24 12 12 85 19 12 12.1 2
JCTER/L1212X2T12 2 2 24 12 12 120 19 12 12.1 2
JCTER/L1212-2T12 2 2 24 12 12 125 19 12 12.1 2
JCTER/L1414-2T12 2 2 24 14 14 125 19 14 14.1 -
JCTER/L1616X2T16 2 2 32 16 16 120 24 16 16.1 -
JCTER/L1616-2T16 2 2 32 16 16 125 24 16 16.1 -
External
JCTER/L1212F3T12 3 3 24 12 12 85 19 12 12.3 2
JCTER/L1212X3T12 3 3 24 12 12 120 19 12 12.3 2
JCTER/L1212-3T12 3 3 24 12 12 125 19 12 12.3 2
JCTER/L1616X3T16 3 3 32 16 16 120 24 16 16.3 -
JCTER/L1616-3T16 3 3 32 16 16 125 24 16 16.3 -
JCTER/L2020H3T16 3 3 32 20 20 100 24 20 20.3 -
JCTER/L2020-3T16 3 3 32 20 20 125 24 20 20.3 -
(1) "f" value is calculated with groove width "W" shown in the table. • øDmax: Max. parting off dia.

Parting-off

Others SPARE PARTS

Designation Clamping screw Wrench
JCTER/L... CSHB-4-A T-15F

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C062 www.tungaloyamerica.com
CG E R /L

Grooving Tool
E x te r n a l d e e p g ro o v i n g & p a r t i n g to o l h o l d e r s f o r s w i s s l a t h e s

ar

b
f
L1 Insert:
øDmax Seat size 1 = DGS1.4-016
L2 Seat size 2, 3, 4, = DGM,
SGM, DGS, SGS, SGN,

h2
DGG

h1

h
Right hand (R) shown.

Metric W Seat size øD max(1) ar h b L1 L2 h1 f (2) h2

CGER/L2020-1.4T14 1.4 1 29/29 9.7 20 20 125 31 20 20.2 -
CGER/L1212-2T17 2 2 35/35 11.8 12 12 150 31 12 12.1 6
CGER/L1616-2T17 2 2 35/35 11.8 16 16 150 31 16 16.1 2
CGER/L2020-2T17 2 2 35/35 9.8 20 20 125 31 20 20.1 -
CGER/L1212-3T19 3 3 38/40 12 12 12 150 31 12 12.3 6
CGER/L1616-3T19 3 3 38/45 14.9 16 16 150 31 16 16.3 2
CGER/L2020-3T19 3 3 38/45 13.2 20 20 125 31 20 20.3 -
CGER/L2020-4T19 4 4 38/55 20.3 20 20 125 33 20 20.4 -
• Wrench, CRW**, should be ordered separately. Insert is clamped by the elastic deformation of upper jaw. (1) DG*/SG*
Maximum diameter of parting off Dmax, can be increased by using SG* insert for some toolholders. (2) "f" value is calculated
SPARE PARTS
with groove width "W" shown in the table. • øDmax: Max. parting off dia.
Designation Wrench
CGER/L2020-1.4T14 CRW23
CGER/L****-2T17 - 4T19 CRW33

CT E FR /L
Too l h o l d e r s f o r E xter nal / Face g ro o v i ng & t u r n i n g
ar
øDmin

b
f

L1 Insert:
L2 DGM, SGM, DGS,
SGS, DTE, DGG,
DTX, DTR, DTF, SGN External
h1

h
Right hand (R) shown.

Inch W (in) W (mm) Seat size ar h1 b h L1 f L2

CTEFR/L12-4T04 0.079, 0.118, 0.157 4 2, 3, 4 0.189 0.750 0.750 0.750 5.000 0.770 1.300
CTEFR/L16-4T04 0.079, 0.118, 0.157 4 2, 3, 4 0.189 1.000 1.000 1.000 6.000 1.020 1.300
CTEFR/L12-6T04 0.197, 0.236 6 5, 6 0.189 0.750 0.750 0.750 5.000 0.236 1.460
Face
CTEFR/L16-6T04 0.197, 0.236 6 5, 6 0.189 1.000 1.000 1.000 6.000 1.020 1.460 Grooving

(1) "f" value is calculated with groove width "W" shown in the table.

SPARE PARTS Parting-off

Designation Clamping screw Wrench
CTEFR/L12-4T04 CM6X1X20-A P-5
CTEFR/L16-4T04 CM6X1X25-A P-5
Others
CTEFR/L12-6T04 CM6X1X20-A P-5
CTEFR/L16-6T04 CM6X1X25-A P-5

Groove width Min. dia. Groove width Min. dia.

Insert for face grooving Insert for face grooving
W (in) øDmin (in) W (in) øDmin (in)
DGM / DGS / SGN 0.078 11.614 DTR 0.118 1.614
DGM / DGS / SGN 0.118 2.126 DTR 0.157 1.417
DGM / DGS / SGN 0.157 1.339 DTR 0.196 2.126
DGM / DGS 0.196 1.929 DTR 0.236 2.126
DGM / DGS 0.236 1.811 DTX 0.118 0.709
DTE / DGG 0.118 1.732 DTX 0.157 0.709
DTE / DGG 0.157 1.654 DTX 0.196 0.787
DTE / DGG 0.196 1.969 DTX 0.236 0.709
DTE / DGG 0.236 1.890 DTF 0.118 0.709
DTF 0.157 0.787
Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C063
 Grooving Tool CA E R /L
B l a d e s f o r ex te r n a l g ro o v i n g & p a r t i n g & t u r n i n g

ar
Insert:

f
DGS, SGS, DGM,
SGM, DTX, DTE,
L1

W
DGG, DTR, SGN

Right hand (R) shown.

Inch W (in) W (mm) Seat size ar L1 f Shank

CAER/L-3T16 0.118 3 3 0.630 1.772 0.409 CHFVL/R...,CHSR/L...
CAER/L-4T16 0.157 4 4 0.630 1.772 0.413 CHFVL/R...,CHSR/L...
CAER/L-5T20 0.197 5 5 0.787 1.929 0.413 CHFVL/R...,CHSR/L...
CAER/L-6T20 0.236 6 6 0.787 1.929 0.413 CHFVL/R...,CHSR/L...

SPARE PARTS
Designation Clamping screw Wrench
CAER/L... BHM6-20-A P-4

C H SR /L
Sh a n k o f to o l ho l d er s f o r CA E R / L & CA FR / L b l a d e s

L1
b
h1

External

L2
h2

Right hand (R) shown.

Inch h b L1 L2 h1 h2 Blade*
CHSR/L12-U 0.075 0.075 5.33 1.378 0.075 0.510 CAER/L...,CAFL/R...
CHSR/L16-U 1.000 1.000 5.33 1.102 1.000 0.280 CAER/L...,CAFL/R...
CHSR/L20-U 1.250 1.250 6.330 1.102 1.250 - CAER/L...,CAFL/R...

Metric h b L1 L2 h1 h2 Blade*
CHSR/L2020 20 20 133 35 20 12 CAER/L...,CAFL/R...
Parting-off
CHSR/L2525 25 25 133 28 25 7 CAER/L...,CAFL/R...
CHSR/L3232 32 32 153 28 32 - CAER/L...,CAFL/R...
Others
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Wrench
CHSR/L... CSHB-6-A P-4

Combination of blade and toolholder

Blade
Toolholders
CAER... CAEL... CAFR... CAFL...
CHSR... 䖃 䖃
CHSL... 䖃 䖃
䖃 : Corresponding

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C064 www.tungaloyamerica.com
CH FVR /L

Grooving Tool
Sha n k o f p e r p e nd i cul ar to o l ho l d er s f o r CA E R / L & CA F R / L b l a d e s

L1

b1

b
L2

h1

h
h2
Right hand (R) shown.

Inch h b L1 L2 h1 h2 b1 Blade
CHFVR/L12-U 0.075 0.075 6.000 0.980 0.075 0.500 0.315 CAEL/R...,CAFR/L...
CHFVR/L16-U 1.000 1.000 6.000 0.980 1.000 0.280 0.118 CAEL/R...,CAFR/L...
CHFVR/L20-U 1.250 1.250 7.000 0.980 1.250 - - CAEL/R...,CAFR/L...

SPARE PARTS
Designation Clamping screw Wrench
CHFVR/L... CSHB-6-A P-4

Combination of blade and toolholder

Blade
Toolholders
CAER... CAEL... CAFR... CAFL...
CHFVR... 䖃 䖃
CHFVL... 䖃 䖃
䖃 : Corresponding

External

Parting-off

Others

Tungaloy C065
 C -C H FV R /L
Grooving Tool
Tu n g Cu t s h a n k o f p er p end i cul ar to o l ho l d e r s f or CA E R / L & CA F R / L b l a d e s

øSS
f1
L1 L3
Right hand (R) shown.

Metric øSS L1 L3 f1
C4CHFVR/L27050N 40 42.5 36 27
C5CHFVR/L35060N 50 49.5 36 35
C6CHFVR/L45065 63 54.5 41 45
C6CHFVR/L45065N 63 54.5 41 45
• The last character of designation is "N": Capable for 7 Mpa coolant pressure.

SPARE PARTS
Designation Coolant parts Coolant parts 1 Plug Clamping screw Wrench
C4CHFVR/L27050N SATZ-M8X1-M3 - SSHM4-4 CSHB-6-A P-4
C5CHFVR/L35060N SATZ-M10X1-M5 - SSHM4-4 CSHB-6-A P-4
C6CHFVR/L45065 CNZ125 PNZ5 - CSHB-6-A P-4
C6CHFVR/L45065N SATZ-M10X1-M5 - SSHM4-4 CSHB-6-A P-4

C -C H S R /L
Tu n g Cu t s h a n k o f to o l ho l d er s f o r CA E R / L & CA F R / L b l a d e s
øSS
f1

L1 L3
Right hand (R) shown.

Metric øSS L1 L3 f1
C4CHSR/L27050N 40 50 36 16.5
C5CHSR/L35060 50 60 36 24.5
C5CHSR/L35060N 50 60 36 24.5
C6CHSR/L45065N 63 65 41 34.5
• The last character of designation is "N": Capable for 7 Mpa coolant pressure.

SPARE PARTS
Designation Coolant parts Coolant parts 1 Plug Clamping screw Wrench
C4CHSR/L27050N SATZ-M8X1-M3 - SSHM4-4 CSHB-6-A P-4
C5CHSR/L35060 CNZ125 PNZ5 - CSHB-6-A P-4
C5CHSR/L35060N SATZ-M10X1-M5 - SSHM4-4 CSHB-6-A P-4
C6CHSR/L45065N SATE-M10X1-M5 - SSHM4-4 CSHB-6-A P-4

Combination of blade and toolholder

Blade
Toolholders
CAER... CAEL... CAFR... CAFL...
C*CHFVR... 䖃 䖃
C*CHFVL... 䖃 䖃
C*CHSR... 䖃 䖃
C*CHSL... 䖃 䖃

䖃 : Corresponding

C066 www.tungaloyamerica.com
CG P

Grooving Tool
B l a d e s f o r ex te r n a l d e e p g ro o v i n g & p a r t i n g

øDmax øDmax

h
Fig.1 W W Fig.3

h1

h
h1
b
L1 b L1 Insert:
150˚
øDmax Seat size 1:DGS1.4-016

h
Fig.2 W 150˚ Seat size 2-6:SGM, SGS,

h1
DGM, DGS, DTX, DGG
b Seat size 8:DGM8, 040
150˚ L1

Inch W (in) W (mm) Seat size øDmax h1 b h L1 Fig

CGP26-1.4S 0.055 1.4 1 1.024 0.843 0.039 1.024 5.906 1
CGP32-1.4D 0.055 1.4 1 1.024 0.976 0.039 1.260 5.906 2
CGP26-2S 0.079 2 2 1.575 0.843 0.071 1.024 5.906 1
CGP32-2D 0.079 2 2 1.969 0.976 0.071 1.260 5.906 2
CGP26-3S 0.118 3 3 1.969 0.843 0.094 1.024 5.906 1
CGP32-3D 0.118 3 3 3.937 0.976 0.094 1.260 5.906 2
CGP26-4S 0.157 4 4 3.150 0.843 0.126 1.024 5.906 1
CGP32-4D 0.157 4 4 3.937 0.980 0.126 1.260 5.906 2
CGP45-4D 0.157 4 4 4.724 1.500 0.126 1.772 5.906 2
CGP32-5D 0.197 5 5 4.724 0.980 0.157 1.260 5.906 2
CGP32-6D 0.236 6 6 4.724 0.980 0.205 1.260 5.906 2
CGP32-8S-CL 0.315 8 8 3.150 0.980 0.244 1.260 5.906 3
• When depth is deeper than (insert length - 0.059"), 1 corner type is recommended. • Wrench (CRW**) should be ordered separately.
• Max groove depth is 1.122".
• øDmax: Max. parting off dia.

SPARE PARTS
Designation Clamping screw Wrench
CGP**-1.4* - CRW23
CGP**-2/3/4/5/6 - CRW33
CGP32-8S-CL CM4X0.7X20-M0-A P-3

External

Caution
햳 : unclamp
Newly developed wrench
Insert is clamped by the elastic deformation of upper jaw. : clamp
Low clamping stress increases the stability and tool life.

햲 Parting-off

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C067
Grooving Tool CTB F
To o l b l o c k f o r C G P b l ad es( f i xed cl am p )

B1

h4
h1

h
L2 L1

h2
L3 Right hand (R) shown.

Inch h B1 L2 L1 b h1 h2 h4 L3 Blade*
CTBF16-45-U 1.000 1.772 0.866 4.331 0.216 1.500 0.984 2.598 1.575 CGP45...
CTBF20-45-U 1.250 1.772 1.102 4.724 0.216 1.500 0.709 2.598 1.772 CGP45...

Metric h B1 L2 L1 b h1 h2 h4 L3 Blade*
CTBF25-45 25 45 22 110 5.5 38.1 25 66 40 CGP45...
CTBF32-45 32 45 28 120 5.5 38.1 18 66 45 CGP45...
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Wrench
CTBF... CM6X1.0X40-A P-5

CTB U
To o l b l o c k f o r C G P and E G P b l ad es
B1

h4

b
h1

L2 L1
h2

L3 Right hand (R) shown.

Inch h1 b B1 L1 h h2 h4 L2 L3 Blade*
CTBU12-26-U 0.843 0.157 1.024 3.386 0.750 0.354 1.693 0.827 1.496 CGP26...
CTBU16-26-U 0.843 0.157 1.024 4.331 1.000 0.197 1.772 0.906 1.654 CGP26...
CTBU12-32-U 0.976 0.209 1.260 3.937 0.750 0.512 1.969 0.748 1.496 CGP32...
CTBU16-32-U 0.976 0.209 1.260 4.331 1.000 0.315 1.969 0.906 1.654 CGP32...
CTBU20-32-U 0.976 0.209 1.260 4.331 1.250 0.197 2.126 1.142 1.890 CGP32...

Metric h1 b B1 L1 h h2 h4 L2 L3 Blade*
CTBU20-26 21.4 4 26 86 20 9 43 21 38 CGP26...
CTBU25-26 21.4 4 26 110 25 5 45 23 42 CGP26...
CTBU20-32 24.8 5.3 32 100 20 13 50 19 38 CGP32...
CTBU25-32 24.8 5.3 32 110 25 8 50 23 42 CGP32...
CTBU32-32 24.8 5.3 32 110 32 5 54 29 48 CGP32...
* Blade sold separately.

SPARE PARTS
Designation Clamp Clamping screw Wrench
CTBU20-26... CT-86 CM6X30-S P-5
CTBU25-26... CT-105 CM6X30-S P-5
CTBU20-32... CT-100 CM6X30-S P-5
CTBU25-32... CT-110 CM6X30-S P-5
CTBU32-32... CT-110 CM6X30-S P-5

C068 www.tungaloyamerica.com
CG E U R /L

Grooving Tool
Exte r n a l 4 5 to o l ho l d er s f o r und ercut t i ng

45°

b
f
w
L1

øDm
L2

h1

h
ar
Right hand (R) shown.

Metric W øDm Seat size ar h b L1 L2 h1 f (1) Insert

CGEUR/L1616-3T02 3 32 3 2.8 16 16 110 30 16 19.3 DTIU...
CGEUR/L2020-3T02 3 32 3 2.8 20 20 125 30 20 23.3 DTIU...
CGEUR/L2525-3T02 3 32 3 2.8 25 25 150 30 25 28.3 DTIU...
CGEUR/L1616-4T02 4 32 4 2.8 16 16 110 31 16 19.5 DTIU...
CGEUR/L2020-4T02 4 32 4 2.8 20 20 125 31 20 23.5 DTIU...
CGEUR/L2525-4T02 4 32 4 2.8 25 25 150 31 25 28.5 DTIU...
CGEUR/L2525-6T03 6 34 5, 6 3.4 25 25 150 35 25 28.9 DTIU...
(1) "f" value is calculated with groove width "W" shown in the table.

SPARE PARTS
Designation Clamping screw Wrench
CGEUR/L****-3T02 CM5X0.8X16-A P-4
CGEUR/L1616-4T02 CM6X1X16-A P-5
CGEUR/L2020-4T02 CM6X1X20-A P-5
CGEUR/L2525-4T02/6T03 CM6X1X25-A P-5

Others

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C069
 Grooving Tool CTI R /L
Bo r i n g b a r s f or sm al l i nter nal g ro o v i ng & t u r n i n g

L2

øDs
f
Insert:

ar øDm
øDm

ar
W L1 Seat size 2:DGIM, DGIS
Seat size 3-8:DTI, DTX

h
seal cap (option) Right hand (R) shown.

Inch W øDm Seat size ar øDs f L1 L2 h Insert

CTIR/L12-3T06-D16 0.118 1.000 3 0.236 0.750 0.609 6.500 1.575 0.551 DGIM..., DGIS...
CTIR/L16-3T05-D16 0.118 1.000 3 0.201 1.000 0.689 8.000 1.575 0.709 DGIM..., DGIS...
CTIR/L16-3T08-D20 0.118 1.250 3 0.315 1.000 0.846 8.000 1.575 0.709 DTI..., DTX...
CTIR/L20-3T10-D25 0.118 1.563 3 0.394 1.250 1.063 10.000 2.362 0.906 DTI..., DTX...
CTIR/L12-4T06-D16 0.157 1.000 4 0.236 0.750 0.609 6.500 1.575 0.906 DTI..., DTX...
CTIR/L16-4T08-D20 0.157 1.250 4 0.315 1.000 0.846 8.000 1.575 1.181 DTI..., DTX...
CTIR/L20-4T04-D20 0.157 1.250 4 0.157 1.250 0.819 10.000 2.362 0.709 DTI..., DTX...
CTIR/L20-4T10-D25 0.157 1.563 4 0.394 1.250 1.063 10.000 2.362 0.906 DTI..., DTX...
CTIR/L16-5T05-D20 0.197 1.250 5 0.197 1.000 0.681 8.000 2.362 1.181 DTI..., DTX...
CTIR/L20-5T10-D25 0.197 1.563 5 0.394 1.250 1.063 10.000 2.362 1.181 DTI..., DTX...
CTIR/L20-6T04-D20 0.236 1.250 6 0.157 1.250 0.820 10.000 2.362 0.906 DTI..., DTX...
CTIR/L20-6T10-D25 0.236 1.563 6 0.394 1.250 1.063 10.000 2.362 1.181 DTI..., DTX...
CTIR/L20-8T05-D23 0.315 1.438 8 0.197 1.250 0.839 10.000 2.362 1.181 DTI..., DTX...
CTIR/L24-8T05-D26 0.315 1.625 8 0.228 1.500 0.982 12.000 2.559 1.181 DTI..., DTX...

Metric W øDm Seat size ar øDs f L1 L2 h Insert

CTIR/L16-2T08-D250 2 25 2 8 16 16.5 125 - 14 DGIM..., DGIS...
CTIR/L20-2T06-D250 2 25 2 6 20 15.8 160 40 18 DGIM..., DGIS...
CTIR/L20-3T06-D250 3 25 3 6 20 15.8 160 40 18 DTI..., DTX...
CTIR/L25-3T05-D250 3 25 3 5.1 25 17.5 200 40 23 DTI..., DTX...
CTIR/L25-3T08-D320 3 32 3 8 25 21.5 200 40 23 DTI..., DTX...
CTIR/L32-3T10-D400 3 40 3 10 32 27 250 60 30 DTI..., DTX...
CTIR/L20-4T06-D250 4 25 4 6 20 15.8 160 40 18 DTI..., DTX...
CTIR/L25-4T08-D320 4 32 4 8 25 21.5 200 40 23 DTI..., DTX...
CTIR/L32-4T04-D310 4 31 4 4 32 20.8 250 60 30 DTI..., DTX...
CTIR/L32-4T10-D400 4 40 4 10 32 27 250 60 30 DTI..., DTX...
CTIR/L25-5T05-D310 5 31 5 5 25 17.3 200 60 23 DTI..., DTX...
Internal CTIR/L32-5T10-D400 5 40 5 10 32 27 250 60 30 DTI..., DTX...
CTIR/L32-6T04-D310 6 31 6 4 32 20.8 250 60 30 DTI..., DTX...
CTIR/L32-6T10-D400 6 40 6 10 32 27 250 60 30 DTI..., DTX...
CTIR/L32-8T05-D370 8 37 8 5 32 21.3 250 60 30 DTI..., DTX...
CTIR/L40-8T05-D420 8 42 8 5.8 40 25.8 300 65 38 DTI..., DTX...
(1) "L1" value is calculated with groove width "W" shown in the table.

Inch Metric
SPARE PARTS SPARE PARTS
Designation Clamping screw Wrench Seal cap Thread type Designation Clamping screw Wrench Seal cap Thread type
Others tor connection tor connection
CTIR/L12-3T06-D16 CM5x0.8x12-A P-4 CA-20 M6 CTIR/L16-2T08-D250 CM5X0.8X10-A P-4 CA-16 M6
CTIR/L16-3T05-D16 CM5x0.8x16-A P-4 CA-25 R1/8" CTIR/L20-2T06-D250 CM5X0.8X12-A P-4 CA-20 M6
CTIR/L16-3T08-D20 CM5x0.8x16-A P-4 CA-25 R1/8" CTIR/L20-3T06-D250 CM5X0.8X12-A P-4 CA-20 M6
CTIR/L20-3T10-D25 CM5x0.8x16-A P-4 CA-32 R1/8" CTIR/L25-3T05-D250 CM5X0.8X16-A P-4 CA-25 R1/8"
CTIR/L12-4T06-D16 CM5x0.8x12-A P-4 CA-20 M6 CTIR/L25-3T08-D320 CM5X0.8X16-A P-4 CA-25 R1/8"
CTIR/L16-4T08-D20 CM5x0.8x16-A P-4 CA-25 R1/8" CTIR/L32-3T10-D400 CM5X0.8X16-A P-4 CA-32 R1/8"
CTIR/L20-4T04-D20 CM5x0.8x16-A P-4 CA-32 R1/8" CTIR/L20-4T06-D250 CM5X0.8X12-A P-4 CA-20 M6
CTIR/L20-4T10-D25 CM5x0.8x16-A P-4 CA-32 R1/8" CTIR/L25-4T08-D320 CM5X0.8X16-A P-4 CA-25 R1/8"
CTIR/L16-5T05-D20 CM6x1x16-A P-5 CA-25 R1/8" CTIR/L32-4T04-D310 CM5X0.8X16-A P-4 CA-32 R1/8"
CTIR/L20-5T10-D25 CM6x1x20-A P-5 CA-32 R1/8" CTIR/L32-4T10-D400 CM5X0.8X16-A P-4 CA-32 R1/8"
CTIR/L20-6T04-D20 CM6x1x20-A P-5 CA-32 R1/8" CTIR/L25-5T05-D310 CM6X1X16-A P-5 CA-25 R1/8"
CTIR/L20-6T10-D25 CM6x1x20-A P-5 CA-32 R1/8" CTIR/L32-5T10-D400 CM6X1X20-A P-5 CA-32 R1/8"
CTIR/L20-8T05-D23 CM6x1x25-A P-5 CA-32 R1/8" CTIR/L32-6T04-D310 CM6X1X20-A P-5 CA-32 R1/8"
CTIR/L24-8T05-D26 CM6x1x25-A P-5 CA-40 R1/8" CTIR/L32-6T10-D400 CM6X1X20-A P-5 CA-32 R1/8"
CTIR/L32-8T05-D370 CM6X1X25-A P-5 CA-32 R1/8"
CTIR/L40-8T05-D420 CM6X1X25-A P-5 CA-40 R1/8"
Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C070 www.tungaloyamerica.com
CG I U R /L

Grooving Tool
B or i n g b a r s f o r i nter nal und ercut t i ng

L2

øDs
45˚
ar

f
w
øDm L1

øDm
h

ar
Right hand (R) shown.

Metric W øDm Seat size ar øDs f (1) L1 L2 h Insert

CGIUR/L20-3T02-D380 3 38 3 2.8 20 12.8 160 - 19 DTIU...
CGIUR/L25-3T02-D380 3 38 3 2.8 25 14.8 200 40 23 DTIU...
CGIUR/L20-4T02-D380 4 38 4 2.8 20 12.9 160 - 19 DTIU...
CGIUR/L25-4T02-D460 4 46 4 2.8 25 14.9 200 40 23 DTIU...
CGIUR/L25-6T02-D460 6 46 5, 6 2.8 25 15.2 200 - 23 DTIU...
(1) "f" value is calculated with groove width "W" shown in the table. .

SPARE PARTS
Designation Clamping screw Wrench
CGIUR/L20-3T02-D380 CM5X0.8X12-A P-4
CGIUR/L25-3T02-D380 CM5X0.8X16-A P-4
CGIUR/L**-4T02-D... CM5X0.8X16-A P-4
CGIUR/L25-6T02-D460 CM6X1X25-A P-5

Others

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C071
 Grooving Tool CTFR /L
To o l h o l d e r s f o r f ace g ro o v i ng & t ur ni ng

øDmax
W
ar ar

b
f
L1 ar
L2 øDm
øDmax

h1

h
Right hand (R) shown.

Metric W øDm øDmax Seat size ar h b L1 L2 h1 f (1)

CTFR/L2525-3T10-024035 3 24 35 3 10 25 25 150 38 25 25.5
CTFR/L2525-3T10-029040 3 29 40 3 10 25 25 150 38 25 25.5
CTFR/L2525-3T10-034050 3 34 50 3 10 25 25 150 38 25 25.5
CTFR/L2525-3T15-044070 3 44 70 3 15 25 25 150 38 25 25.5
CTFR/L2525-3T15-064100 3 64 100 3 15 25 25 150 38 25 25.5
CTFR/L2525-4T10-022036 4 22 36 4 10 25 25 150 39 25 25.6
CTFR/L2525-4T20-028042 4 28 42 4 20 25 25 150 39 25 25.6
CTFR/L2525-4T20-034050 4 34 50 4 20 25 25 150 39 25 25.6
CTFR/L2525-4T20-042070 4 42 70 4 20 25 25 150 39 25 25.6
CTFR/L2525-4T20-062120 4 62 120 4 20 25 25 150 39 25 25.6
CTFR/L2525-4T20-112200 4 112 200 4 20 25 25 150 39 25 25.6
CTFR/L2525-5T25-050080 5 50 80 5 25 25 25 150 49 25 25.6
CTFR/L2525-5T25-070110 5 70 110 5 25 25 25 150 49 25 25.6
CTFR/L2525-5T25-100150 5 100 150 5 25 25 25 150 49 25 25.6
CTFR/L2525-5T25-140200 5 140 200 5 25 25 25 150 49 25 25.6
CTFR/L2525-6T25-048070 6 48 70 6 25 25 25 150 49 25 25.6
CTFR/L2525-6T25-058100 6 58 100 6 25 25 25 150 49 25 25.6
CTFR/L2525-6T25-088180 6 88 180 6 25 25 25 150 49 25 25.6
CTFR/L2525-6T25-168400 6 168 400 6 25 25 25 150 49 25 25.6
• When depth is deeper than (insert length - 1.5 mm), 1 corner type is recommended.
(1) "f" value is calculated with groove width "W" shown in the table.
• When DTF insert is installed, Max "ar" should be 15 mm.

SPARE PARTS
Designation Clamping screw Wrench
CTFR/L2525-3T - 4T... CM6X1X25-A P-5
CTFR/L2525-5T - 6T... CM8X1.25X25-A P-6

INSERT
Face
Grooving
Insert
Designation seat Insert
size
CTFR/L2525-3T10-024035 3 DTF, DTX
CTFR/L2525-3T10-029040 3 DTF, DTX
CTFR/L2525-3T10-034050 3 DTF, DTX
Others CTFR/L2525-3T15-044070 3 DTF, DTX, DTE, DTR
CTFR/L2525-3T15-064100 3 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFR/L2525-4T10-022036 4 DTF, DTX
CTFR/L2525-4T20-028042 4 DTF, DTX
CTFR/L2525-4T20-034050 4 DTF, DTX
CTFR/L2525-4T20-042070 4 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFR/L2525-4T20-062120 4 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFR/L2525-4T20-112200 4 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFR/L2525-5T25-... 5 DTX, DTE, DGG, DGM, DGS, DTR
CTFR/L2525-6T25-... 6 DTX, DTE, DGG, DGM, DGS, DTR

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C072 www.tungaloyamerica.com
CT FV R /L

Grooving Tool
Per p e n d i c u l a r too l ho l d er s f o r f ace g ro o v i ng a n d t u r n i n g

øDmax
b
ar
W
L2 L1 øDm
øDmax
ar

h1

h
Right hand (R) shown.

Metric W øDm øDmax Seat size ar h b L1 L2 h1

CTFVR/L2525-3T10-024035 3 24 35 3 10 25 25 150 18 25
CTFVR/L2525-3T10-029040 3 29 40 3 10 25 25 150 18 25
CTFVR/L2525-3T10-034050 3 34 50 3 10 25 25 150 18 25
CTFVR/L2525-3T15-044060 3 44 60 3 15 25 25 150 18 25
CTFVR/L2525-3T15-054085 3 54 85 3 15 25 25 150 18 25
CTFVR/L2525-4T12-022040 4 22 40 4 12 25 25 150 18.5 25
CTFVR/L2525-4T15-032050 4 32 50 4 15 25 25 150 18.5 25
CTFVR/L2525-4T15-042060 4 42 60 4 15 25 25 150 18.5 25
CTFVR/L2525-4T15-052085 4 52 85 4 15 25 25 150 18.5 25
CTFVR/L2525-5T20-050080 5 50 80 5 20 25 25 150 22 25
CTFVR/L2525-5T20-070110 5 70 110 5 20 25 25 150 22 25
CTFVR/L2525-5T20-100150 5 100 150 5 20 25 25 150 22 25
CTFVR/L2525-5T20-140200 5 140 200 5 20 25 25 150 22 25
CTFVR/L2525-6T20-048085 6 48 85 6 20 25 25 150 22 25
CTFVR/L2525-6T20-073150 6 73 150 6 20 25. 25 150 22 25
CTFVR/L2525-6T20-138250 6 138 250 6 20 25 25 150 22 25
• When depth is deeper than (insert length - 1.5 mm), 1 corner type is recommended.

SPARE PARTS (1) Min. diameter øDm of DTE, DGS and DGM insert
Designation Clamping screw Wrench
CTFVR/L2525-3T... CM5X0.8X25-A P-4 Insert øDm Note
CTFVR/L2525-4T... CM6X1X25-A P-5 When diameter is smaller
DTE3 / DGS3 / DGM3 ø92
CTFVR/L2525-5T..., 6T... CM8X1.25X25-A P-6
than øDm, DTF or DTX type
DTE4 / DGS4 / DGM4 ø42 insert is recommended.
INSERT
Insert
Designation seat Insert
size
CTFVR/L2525-3T10-024035 3 DTF, DTX
Face
CTFVR/L2525-3T10-029040 3 DTF, DTX Grooving

CTFVR/L2525-3T10-034050 3 DTF, DTX, DTR

CTFVR/L2525-3T15-044060 3 DTF, DTX, DTE, DTR
CTFVR/L2525-3T15-054085 3 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFVR/L2525-4T12-022040 4 DTF, DTX
CTFVR/L2525-4T15-032050 4 DTF, DTX Others
CTFVR/L2525-4T15-042060 4 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFVR/L2525-4T15-052085 4 DTF, DTX, DTE, DGG, DGM, DGS, DTR
CTFVR/L2525-5T20-... 5 DTX, DTE, DGG, DGM, DGS, DTR
CTFVR/L2525-6T20-... 6 DTX, DTE, DGG, DGM, DGS, DTR

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C073
 Grooving Tool CA FR /L
Bl a d e s f o r f a ce g ro o v i ng & t ur ni ng

L1

W
f
ar Insert:
øDm CAFR/L-3T12-040055:DTF
Seat size 3(2)-6:DTF(3), DTE,
øDmax DGG, DTX, DGS, DGM,
DTR
Shank:
CHFVR/L, CHSR/L
Right hand (R) shown.

Inch W øDm øDmax Seat size ar L1 f (1)

CAFR/L-3T12-040055 0.118 1.575 2.165 3 0.472 1.772 0.409
CAFR/L-3T12-055075 0.118 2.165 2.953 3 0.472 1.772 0.409
CAFR/L-3T12-075100 0.118 2.953 3.937 3 0.472 1.772 0.409
CAFR/L-3T12-100140 0.118 3.937 5.512 3 0.472 1.772 0.409
CAFR/L-3T12-140200 0.118 5.512 7.874 3 0.472 1.772 0.409
CAFR/L-4T16-050070 0.157 1.969 2.756 4 0.630 1.772 0.413
CAFR/L-4T16-070100 0.157 2.756 3.937 4 0.630 1.772 0.413
CAFR/L-4T16-100150 0.157 3.937 5.906 4 0.630 1.772 0.413
CAFR/L-4T16-150250 0.157 5.906 9.843 4 0.630 1.772 0.413
CAFR/L-5T20-055080 0.197 2.165 3.150 5 0.787 1.929 0.413
CAFR/L-5T20-080120 0.197 3.150 4.724 5 0.787 1.929 0.413
CAFR/L-5T20-120180 0.197 4.724 7.087 5 0.787 1.929 0.413
CAFR/L-5T20-180300 0.197 7.087 11.811 5 0.787 1.929 0.413
CAFR/L-5T20-300000 0.197 11.811 ∞ 5 0.787 1.929 0.413
CAFR/L-6T25-060090 0.236 2.362 3.543 6 0.984 2.165 0.413
CAFR/L-6T25-090150 0.236 3.543 5.906 6 0.984 2.165 0.413
CAFR/L-6T25-150250 0.236 5.906 9.843 6 0.984 2.165 0.413
CAFR/L-6T25-250400 0.236 9.843 15.748 6 0.984 2.165 0.413
• When depth is deeper than (insert length - 0.059"), 1 corner type is recommended.
(1) "f" value is calculated with groove width "W" shown in the table.
(2) Not applicable for CAFR/L-3T12-040055
(3) Seat sizes of DTF are Only 3 and 4

SPARE PARTS
Designation Clamping screw Wrench
CAFR/L... BHM6-20-A P-4

Min. diameter øDm of DTE, DGS and DGM insert

Insert øDm Note
Face
Grooving DTE 3 / DGS 3 / DGM 3 ø1.733 When diameter is smaller
DTE 4 / DGS 4 / DGM 4 ø1.654
than øDm, DTF or DTX type
DTE 5 / DGS 5 / DGM 5 ø1.969
insert is recommended.
DTE 6 / DGS 6 / DGM 6 ø1.890

Others

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C074 www.tungaloyamerica.com
CH SR /L

Grooving Tool
Sha n k o f to o l h o l d er s f o r CA E R / L & CA FR / L b l a d e s

L1

b
h1

h
h2
L2
Right hand (R) shown.

Inch h b L1 L2 h1 h2 Blade*
CHSR/L12-U 0.750 0.750 5.330 1.378 0.075 0.510 CAER/L...,CAFL/R...
CHSR/L16-U 1.000 1.000 5.330 1.102 1.000 0.280 CAER/L...,CAFL/R...
CHSR/L20-U 1.250 1.250 6.330 1.102 1.250 - CAER/L...,CAFL/R...

Metric h b L1 L2 h1 h2 Blade*
CHSR/L2020 20 20 133 35 20 12 CAER/L...,CAFL/R...
CHSR/L2525 25 25 133 28 25 7 CAER/L...,CAFL/R...
CHSR/L3232 32 32 153 28 32 - CAER/L...,CAFL/R...
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Wrench
CHSR/L... CSHB-6-A P-4

CH FVR /L
Sha n k o f p e r p e nd i cul ar to o l ho l d er s f o r CA E R / L & CA F R / L b l a d e s

L1
b1

L2
h1

h
h2

Right hand (R) shown.

Inch h b L1 L2 h1 h2 b1 Blade*
CHFVR/L12-U 0.750 0.750 6.000 0.980 0.075 0.500 0.350 CAEL/R...,CAFR/L...
CHFVR/L16-U 1.000 1.000 6.000 0.980 1.000 0.280 0.120 CAEL/R...,CAFR/L...
CHFVR/L20-U 1.250 1.250 7.000 0.980 1.250 - - CAEL/R...,CAFR/L...

Metric h b L1 L2 h1 h2 b1 Blade*
CHFVR/L2020 20 20 150 25 20 12 8 CAEL/R...,CAFR/L...
CHFVR/L2525 25 25 150 25 25 7 3 CAEL/R...,CAFR/L...
CHFVR/L3232 32 32 170 25 32 - - CAEL/R...,CAFR/L...
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Wrench
CHFVR/L... CSHB-6-A P-4

Combination of blade and toolholder

Blade
Toolholders
CAER... CAEL... CAFR... CAFL...
CHSR... 䖃 䖃
CHSL... 䖃 䖃
CHFVR... 䖃 䖃
CHFVL... 䖃 䖃
䖃 : Corresponding

Tungaloy C075
 C -C H FVR /L
Grooving Tool
Tu n g C u t s h a nk o f p er p end i cul ar to o l ho l d e r s f or CA E R / L & CA F R / L b l a d e s

SS
f1
L1 L3
Right hand (R) shown.

Metric SS L1 L3 f1 Blade*
C4CHFVR/L27050N 40 42.5 36 27 CAEL/R..., CAFR/L...
C5CHFVR/L35060N 50 49.5 36 35 CAEL/R..., CAFR/L...
C6CHFVR/L45065 63 54.5 41 45 CAEL/R..., CAFR/L...
C6CHFVR/L45065N 63 54.5 41 45 CAEL/R..., CAFR/L...
* Blade sold separately.
• The last character of designation is "N":Capable for 7Mpa, coolant pressure.

SPARE PARTS
Designation Coolant parts Coolant parts 1 Plug Clamping screw Wrench
C4CHFVR/L27050N SATZ-M8X1-M3 - SSHM4-4 CSHB-6-A P-4
C5CHFVR/L35060N SATZ-M10X1-M5 - SSHM4-4 CSHB-6-A P-4
C6CHFVR/L45065 CNZ125 PNZ5 - CSHB-6-A P-4
C6CHFVR/L45065N SATZ-M10X1-M5 - SSHM4-4 CSHB-6-A P-4

C -C H SR /L
Tu n g C u t s h a nk o f to o l ho l d er s f o r CA E R / L & CA F R / L b l a d e s
SS
f1

L3
L1
Right hand (R) shown.

Metric SS L1 L3 f1 Blade
C4CHSR/L27050N 40 50 36 16.5 CAER/L..., CAFL/R...
C5CHSR/L35060 50 60 36 24.5 CAER/L..., CAFL/R...
C5CHSR/L35060N 50 60 36 24.5 CAER/L..., CAFL/R...
C6CHSR/L45065N 63 65 41 34.5 CAER/L..., CAFL/R...
• The last character of designation is "N":Capable for 7Mpa, coolant pressure.

SPARE PARTS
Designation Coolant parts Coolant parts 1 Clamping screw Wrench
C4CHSR/L27050N SATZ-M8X1-M3 - CSHB-6-A P-4
C5CHSR/L35060 CNZ125 PNZ5 CSHB-6-A P-4
C5CHSR/L35060N SATZ-M10X1-M5 - CSHB-6-A P-4
C6CHSR/L45065N SATZ-M10X1-M5 - CSHB-6-A P-4

Combination of blade and toolholder

Blade
Toolholders
CAER... CAEL... CAFR... CAFL...
C*CHFVR... 䖃 䖃
C*CHFVL... 䖃 䖃
C*CHSR... 䖃 䖃
C*CHSL... 䖃 䖃
䖃 : Corresponding

C076 www.tungaloyamerica.com
CT I FR /L

Grooving Tool
Too l h o l d e r s f o r face / i nter nal f ace g ro o v i ng & t u r n i n g

øDmin
ar

øDs
f
L1

øDmax
øDm
h1 W
Insert:
DGM, DGS,
øDm DGG, DTE,
DTF, DTX, DTR

Right hand (R) shown.

Inch W Seat size ar øDs h1 L 1(1) f

CTIFR/L16-4T05-D17 0.118, 0.157 3, 4 0.217 1.000 0.450 8.000 1.030
CTIFR/L20-4T05-D22 0.118, 0.157 3, 4 0.217 1.250 0.590 10.000 1.280
CTIFR/L16-5T05-D17 0.197, 0.236 5, 6 0.217 1.000 0.450 8.000 1.030
CTIFR/L20-5T05-D22 0.197, 0.236 5, 6 0.217 1.250 0.590 10.000 1.280

Metric W Seat size ar øDs h1 L1(1) f

CTIFR/L25-4T05-D270 4 3, 4 5.5 25 11.5 200 13.3
CTIFR/L32-4T05-D340 4 3, 4 5.5 32 15 250 16.8
CTIFR/L25-5T05-D270 6 5, 6 5.5 25 11.5 200 13.3
CTIFR/L32-5T05-D340 6 5, 6 5.5 32 15 250 16.8
(1) "f" value is calculated with groove width "W" shown in the table.**

Inch
SPARE PARTS
Designation Clamping screw Wrench
CTIFR/L16-4T05-D17 CM6X1X16-A P-5
CTIFR/L20-4T05-D22 CM6X1X20-A P-5
CTIFR/L16-5T05-D17 CM6X1X16-A P-5
CTIFR/L20-5T05-D22 CM6X1X20-A P-5

Insert Min. bore dia. øDm Insert øDmin

seat seat øDmax
size øDs = 0.984" øDs = 1.259" size DGM, DGS, DGG DTE DTF / DTX DTR
3 1.035 1.311 3 2.126 1.732 0.787 1.614 ∞
4 1.055 1.331 4 1.339 1.654 0.709 1.417 ∞
5 1.035 1.311 5 1.929 1.969 0.787 2.126 ∞
6 1.055 1.331 6 1.811 1.890 0.709 2.126 ∞

Metric
SPARE PARTS Face
Grooving
Designation Clamping screw Wrench
CTIFR/L25-4T05-D270 CM6X1X16-A P-5
CTIFR/L32-4T05-D340 CM6X1X20-A P-5
CTIFR/L25-5T05-D270 CM6X1X16-A P-5
CTIFR/L32-5T05-D340 CM6X1X20-A P-5
Others
Insert Min. bore dia. øDm Insert øDmin
seat seat øDmax
size øDs = 25 mm øDs = 32 mm size DGM, DGS, DGG DTE DTF / DTX DTR
3 26.3 33.3 3 92 62 19 44 ∞
4 26.8 33.8 4 37 42 20 32 ∞
5 26.3 33.3 5 60 64 20 48 ∞
6 26.8 33.8 6 57 61 23 48 ∞

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

Tungaloy C077
 Grooving Tool CTER /L-15A
To o l h o l d e r s f o r m achi ni ng al um i num w hee l , s q u a re s h a n k

ar

b
w
f
L1
15˚

h1

h
h2
L2 Right hand (R) shown.

Metric W Seat size ar h b L1 f L2 h1 h2 Insert

CTER/L2525-6T25-15A 6 6 25 25 25 150 32.2 50.5 25 7 DTA...
CTER/L2525-8T30-15A 8 8 30 25 25 150 32.9 55 25 7 DTA...

SPARE PARTS
Designation Clamping screw Wrench
CTER/L2525-****-15A CM6X1X25-A P-5

C G I U R /L-15A
Bo r i n g b a r s f or m achi ni ng al um i num w hee l

ar

øDs
w
f

L1
15˚

h
h1

øDm L2 Right hand (R) shown.

Metric W øDm Seat size ar øDs f L1 L2 h h1 Insert

CGIUR/L40-6T50-D160-15A 6 160 6 50 40 19.7 320 60 38.5 19 DTA...
CGIUR/L40-8T83-D160-15A 8 160 8 83 40 20.5 320 85 38.5 19 DTA...
CGIUR/L50-6T85-D200-15A 6 200 6 85 50 25.2 350 85 48.5 23.5 DTA...
CGIUR/L50-8T85-D200-15A 8 200 8 85 50 25.9 350 85 48.5 23.5 DTA...

SPARE PARTS
Designation Clamping screw Wrench
CGIUR/L**-15A CM6X1X25-A P-5

Nozzle parts
Coolant pipe Coolant nozzle
PNZ5 CNZ125
Others

Reference pages
Inserts → C079 - C091, Standard cutting conditions → C091

C078 www.tungaloyamerica.com
 - Chipbreaker Guide

Grooving Tool
External grooving and parting
DGM type (2 corners) 1st choice for external grooving Standard feed
SGM type (1 corner) and parting off 0.020
Smooth chip evacuation 0.016

Feed: f (ipr)
Well-designed edge with 0.012

high strength 0.008

0.004
Handed insert available
0
0.079 0.118 0.157 0.197 0.236 0.315
W = 0.079" - 0.315" Groove width: W (in)
Page C083

DGS type (2 corners) Lower cutting force and Standard feed

SGS type (1 corner) superior sharpness
0.020
Unique-designed edge 0.016

Feed: f (ipr)
and chipbreaker 0.012

Handed insert available 0.008

0.004
W = 0.055" - 0.236"
0
0.055 0.079 0.118 0.157 0.197 0.236
Page C084, C085 Groove width: W (in)

External and face grooving, and turning

Standard feed and DoC
DTE type (2 corners) For general purpose 0.200

0.160
Depth of cut

Unique chipbreaker Standard feed

ap (in)

0.120
makes chips shorter 0.016
0.080

Molded and ground 0.012

Feed: f (ipr)

0.040
insert available 0
0.008
0.004 0.008 0.012 0.016 0.020 0.024
0.004
Feed: f (ipr)
W = 0.104" - 0.315"
Groove width: W (in) 0
0.118 0.157 0.197 0.236 0.315
Page C086, C087 0.118 0.157 0.196 0.236 0.315
Groove width: W (in)

External and face grooving

For non-ferrous materials
DGG type (2 corners) and titanium Standard feed

Chipbreaker with low 0.016

Feed: f (ipr)

cutting force 0.012

0.008
Sharp cutting edge that 0.004
prevents vibration and 0 0.079 0.118 0.157 0.197 0.236
delivers fine surface finish Groove width: W (in)
W = 0.079" - 0.236"
Page C087

Tungaloy C079
Grooving Tool
- Chipbreaker Guide
External, internal and face grooving, and turning
Standard feed and DoC
DTX type (2 corners) Multi-functional type
0.157

Well balanced Standard feed

Depth of cut
0.118

ap (in)
sharpness and strength 0.078 0.016

Feed: f (ipr)
0.012
Multi functional insert 0.039
0.008
W = 0.118" - 0.236" 0
0.004 0.008 0.012 0.016 0.004
Feed: f (ipr)
Groove width: W (in) 0
0.118 0.157 0.197 0.236
Page C087 0.118 0.157 0.196 0.236 Groove width: W (in)

External grooving
Standard feed
DGE type (2 corners) For high accurate and
shallow groove 0.020
0.016

Feed: f (ipr)
Excellent chip control 0.012

0.008
W = 0.039" - 0.085"
0.004

0
0.039 0.051 0.062 0.072 0.085
Groove width: W (in)
Page C086

Profiling and undercutting

Standard feed and DoC
DTR type (2 corners) Full radius type 0.200

Excellent chip control 0.157

Molded
Depth of cut

0.118
ap (in)

Molded and ground 0.078

insert available 0.039
0
Ground W = 0.118" - 0.315" 0.004 0.008 0.012 0.016 0.020 0.024 0.028
Feed: f (ipr)

Groove width: W (in)

0.118 0.157 0.196 0.236 0.315
Page C089, C090

DTIU type (2 corners) Full radius type Standard feed and DoC
0.016
Excellent chip control
Feed: f (ipr)

0.012
For undercutting
0.008
W = 0.118" - 0.236" 0.004

0
0.118 0.157 0.197 0.236
Groove width: W (in)

Page C090

C080 www.tungaloyamerica.com
 Grooving Tool
Internal grooving and turning
1st choice for Standard feed and DoC
DTI type (2 corners) internal grooving 0.200
0.157

Depth of cut
Unique chipbreaker Standard feed
0.118

ap (in)
makes chips shorter 0.016
0.078

Feed: f (ipr)
0.012
Molded and ground 0.039

insert available 0 0.008

0.004 0.008 0.012 0.016 0.020 0.024
Feed: f (ipr) 0.004
W = 0.118" - 0.315"
Groove width: W (in) 0 0.118 0.157 0.197 0.236 0.315
Page C088 0.118 0.157 0.196 0.236 0.315 Groove width: W (in)

Small diameter internal grooving

DGIM type 2 mm insert width only (For general purpose) Standard feed
(2 corners) Unique chipbreaker for excellent chip 0.016
control

Feed: f (ipr)
0.012

Excellent fracture resistance due to 0.008

optimum land on the cutting edge 0.004

For general applications on steels & 0 0.079

stainless steels Groove width

W (in)
Page C089 W = 0.079"

DGIS type 2 mm insert width only (Lower cutting force） Standard feed
(2 corners) Low cutting force due to a 0.016
Feed: f (ipr)

unique land geometry 0.012

0.008
Applicable for low carbon steels
0.004
& stainless steels
0 0.079
W = 0.079" Groove width
W (in)
Page C089

Face grooving and turning

Standard feed and DoC
DTF type (2 corners) 1st choice for 0.200
face grooving 0.157
Depth of cut

Standard feed
Unique chipbreaker 0.118
ap (in)

0.016
makes chips shorter 0.078
Feed: f (ipr)

0.012
Handed insert 0.039
0.008
0 0.004 0.008 0.012 0.016 0.020 0.024
W = 0.118" - 0.157" 0.004
Feed: f (ipr)
Groove width: W (in) 0
0.118 0.157
0.118 0.157 Groove width: W (in)
Page C088

Tungaloy C081
Grooving Tool
- Chipbreaker Guide
Aluminum wheel machining
DTA type Standard feed and DoC
Full radius type 0.200
(2 corners)

Depth of cut
0.157
Excellent chip control

ap (in)
0.118

For aluminum wheel 0.078

0.039
profiling
0
0.004 0.008 0.012 0.016 0.020 0.024
Ground insert
Feed: f (ipr)
W = 0.236" - 0.315" Groove width : W (in)
0.236 0.315
Page C090

External grooving of hardened steels

SGN-CBN type For hardened steel cutting Standard feed
(1 corner) Optimum cutting edge 0.0040

shape for grooving of hard- 0.0032

Feed: f (ipr)
ened steels 0.0024

High tolerance width for 0.0016

finishing（W = ±0.001") 0.0008

W = 0.079" - 0.157" 0
0.079 0.118 0.157
Groove width: W (in)
Page C091

C082 www.tungaloyamerica.com
 INSERT
DG M

Grooving Tool
E x te r n a l g ro o v i n g a n d p a r t i n g o f f , 2 c o r n e r

Neutral Left hand Right hand

rε rε rε

W
θ˚ θ˚
7˚
L L L
h 7˚ 7˚

h
h
Coated Cermet
Insert
Designation seat W±0.05 W±0.002 rε T9125 AH7025 AH725 AH905 GH130 NS9530 L h
size θ°
(mm) (in) (in) R L R L R L R L R L R L (in) (in)
DGM2-020 2 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGM2-020-6R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 6

DGM2-020-8R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 8

DGM2-020-15R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 15

DGM2-002-15R/L 2 2 0.079 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 15

DGM3-020 3 3 0.118 0.008 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGM3-020-6R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

DGM3-002-6R/L 3 3 0.118 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 6

DGM3-020-15R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

DGM4-030 4 4 0.157 0.012 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGM4-030-4R/L 4 4 0.157 0.012 䖃 䖃 䖃 䖃 0.787 0.197 4

DGM4-030-15R/L 4 4 0.157 0.012 䖃 䖃 䖃 䖃 0.787 0.197 15

DGM5-030 5 5 0.197 0.012 䖃 䖃 䖃 䖃 䖃 䖃 0.984 0.217 0

DGM5-030-4R 5 5 0.197 0.012 䖃 䖃 0.787 0.217 4

DGM6-030 6 6 0.236 0.012 䖃 䖃 䖃 䖃 䖃 0.984 0.217 0

DGM8-040 8 8 0.315 0.016 䖃 䖃 䖃 1.181 0.264 0

䖃 : Line up

SGM
E x te r n a l d e e p g ro o v i n g a n d p a r t i n g o f f , 1 c o r n e r

rε Left hand Right hand

Neutral rε
rε
W

θ˚ θ˚
L 7˚
L L
7˚ 7˚
h
h

Coated
Insert
Designation seat W±0.05 W±0.002 rε AH725 GH130 L h
size θ°
(mm) (in) (in) R L R L (in) (in)
SGM2-020 2 2 0.079 0.008 䖃 䖃 0.787 0.197 0

SGM2-020-6R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

SGM3-020 3 3 0.118 0.008 䖃 䖃 0.787 0.197 0

SGM3-020-6R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

SGM3-020-15R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

SGM4-030 4 4 0.157 0.012 䖃 䖃 0.787 0.197 0

SGM4-030-4R/L 4 4 0.157 0.012 䖃 䖃 䖃 䖃 0.787 0.197 4

SGM5-030 5 5 0.197 0.012 䖃 䖃 0.984 0.217 0

SGM6-030 6 6 0.236 0.012 䖃 䖃 0.984 0.217 0

䖃 : Line up

Tungaloy C083
 DGS
Grooving Tool E x te r n a l g ro o v i n g a n d p a r t i n g o f f , 2 c o r n e r

rε Neutral Left hand rε rε Right hand

W
θ˚ θ˚
7˚ L L L
7˚ 7˚

h
h
Coated Cermet
Insert
Designation seat W±0.05 W±0.002 rε T9125 AH7025 AH725 GH130 NS9530 L h
size θ°
(mm) (in) (in) R L R L R L R L R L (in) (in)
DGS1.4-016 1 1.4 0.055 0.006 䖃 䖃 0.630 0.169 0

DGS2-020 2 2 0.079 0.008 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGS2-020-6R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

DGS2-002-6R/L 2 2 0.079 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 6

DGS2-020-15R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

DGS2-002-15R/L 2 2 0.079 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 15

DGS3-020 3 3 0.118 0.008 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGS3-020-6R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

DGS3-002-6R/L 3 3 0.118 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 6

DGS3-020-15R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

DGS3-002-15R/L 3 3 0.118 0.0008 䖃 䖃 䖃 䖃 0.772 0.197 15

DGS4-030 4 4 0.157 0.012 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0

DGS4-030-4R/L 4 4 0.157 0.012 䖃 䖃 䖃 䖃 0.787 0.197 4

DGS5-030 5 5 0.197 0.012 䖃 䖃 䖃 䖃 0.984 0.217 0

DGS6-030 6 6 0.236 0.012 䖃 䖃 䖃 0.984 0.217 0

䖃 : Line up

Caution
Designation øDmax (in) Designation øDmax (in)
DGM2-002-15R/L 1.102 DGS2-002-15R/L 1.102 ax
m
øD
DGM3-002-15R/L 1.141 DGS3-002-15R/L 1.141
DGM4-030-15R/L 1.181 SGS3-020-15R/L 4.055
SGM3-020-15R/L 4.055 SGS3-002-15R/L 1.338
The tool will interfere with the workpiece when grooving
larger diameter than øDmax.

C084 www.tungaloyamerica.com
 SGS
E x te r n a l d e e p g ro o v i n g a n d p a r t i n g o f f , 1 c o r n e r

Grooving Tool
rε Neutral Left hand rε Right hand
rε

W
θ˚ θ˚
7˚ L L 7˚ L
7˚
h

h
h
Coated
Insert
Designation seat W±0.05 W±0.002 rε AH725 GH130 L h
size θ°
(mm) (in) (in) R L R L (in) (in)
SGS2-020 2 2 0.079 0.008 䖃 䖃 0.787 0.197 0

SGS2-020-6R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197 6

SGS2-020-15R/L 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

SGS3-020 3 3 0.118 0.008 䖃 䖃 0.787 0.197 0

SGS3-020-6R/L 3 3 0.118 0.0008 䖃 䖃 䖃 䖃 0.787 0.197 6

SGS3-002-6R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.780 0.197 6

SGS3-020-15R/L 3 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.197 15

SGS3-002-15R/L 3 3 0.118 0.0008 䖃 䖃 䖃 䖃 0.787 0.197 15

SGS4-030 4 4 0.157 0.012 䖃 䖃 0.787 0.197 0

SGS5-030 5 5 0.197 0.012 䖃 䖃 0.984 0.217 0

SGS6-030 6 6 0.236 0.012 䖃 䖃 0.984 0.217 0

䖃 : Line up

Tungaloy C085
 DGE
Grooving Tool E x ter nal gro ov in g (fo r hig h-precisio n machining)

rε
G

hW 7˚ L

Insert W±0.02 W±0.001 rε Coated Cermet G L h

Designation seat
size (mm) (in) (in) AH725 GH130 NS9530 (in) (in) (in)
DGE100-000 2 1 0.039 0 䖃 䖃 䖃 0.100 0.787 0.197

DGE130-000 2 1.3 0.051 0 䖃 䖃 䖃 0.100 0.787 0.197

DGE160-010 2 1.6 0.063 0.004 䖃 䖃 䖃 0.100 0.787 0.197

DGE185-010 2 1.85 0.073 0.004 䖃 䖃 䖃 0.140 0.787 0.197

DGE215-015 2 2.15 0.085 0.006 䖃 䖃 䖃 0.140 0.787 0.197

䖃 : Line up

Caution
øDmax is limited as shown in the picture to the right according to
øDmax
the groove depth, G.D. Please refer to the following table. G.D.
G.D = Groove depth
Max. groove øDmax (in)
Designation depth (in) G.D. = 0.039 G.D. = 0.059 G.D. = 0.078 G.D. = 0.098 G.D. = 0.118
DGE100-000
DGE130-000 0.078 - - Relevant area
DGE160-010 – 0.73 0.45
(Interference)
DGE185-010
0.118 0.35 0.28
DGE215-015

DTE
E x ter nal, g ro ov i ng and turning (fo r hig h-p recision m achining)

rε
W

7˚ L
h

Insert W±0.02 W±0.001 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH7025 AH725 GH130 NS9530 (in) (in)
DTE265-015 3 2.65 0.104 0.006 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTE300-020 3 3 0.118 0.008 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTE300-040 3 3 0.118 0.016 䖃 䖃 䖃 䖃 0.787 0.197

DTE315-015 3 3.15 0.124 0.006 䖃 䖃 䖃 䖃 0.787 0.197

DTE400-040 4 4 0.157 0.016 䖃 䖃 䖃 䖃 0.787 0.197

DTE400-080 4 4 0.157 0.031 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTE415-015 4 4.15 0.163 0.006 䖃 䖃 䖃 䖃 0.787 0.197

DTE478-055 5 4.78 0.188 0.022 䖃 䖃 䖃 䖃 0.984 0.217

DTE500-040 5 5 0.197 0.016 䖃 䖃 䖃 䖃 0.984 0.217

DTE500-080 5 5 0.197 0.031 䖃 䖃 䖃 䖃 䖃 0.984 0.217

DTE515-015 5 5.15 0.203 0.006 䖃 䖃 䖃 0.984 0.217

DTE600-080 6 6 0.236 0.031 䖃 䖃 䖃 䖃 0.984 0.217

DTE600-120 6 6 0.236 0.047 䖃 䖃 䖃 0.984 0.217

DTE800-080 8 8 0.315 0.031 䖃 䖃 䖃 1.181 0.264

DTE800-120 8 8 0.315 0.047 䖃 䖃 䖃 1.181 0.264

䖃 : Line up

C086 www.tungaloyamerica.com
DT E
E xter nal, groo v ing and turning

Grooving Tool
rε

W 7˚ L
h

Insert W±0.05 W±0.001 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH7025 AH725 GH130 NS9530 (in) (in)
DTE3-040 3 3 0.118 0.016 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTE4-040 4 4 0.157 0.016 䖃 䖃 䖃 䖃 䖃 0.787 0.197

䖃 : Line up

DG G
E xter nal and f ace gro o ving (fo r hig h-p recisio n ma chining)

rε
W

7˚ L
h

Insert W±0.02 W±0.001 rε Cermet Uncoated L h

Designation seat
size (mm) (in) (in) NS9530 KS05F (in) (in)
DGG200-020 2 2 0.079 0.008 䖃 䖃 0.787 0.197

DGG300-020 3 3 0.118 0.008 䖃 䖃 0.787 0.197

DGG400-040 4 4 0.157 0.016 䖃 䖃 0.787 0.197

DGG500-040 5 5 0.197 0.016 䖃 䖃 0.984 0.217

DGG600-040 6 6 0.236 0.016 䖃 䖃 0.984 0.217

䖃 : Line up

DT X
E xter nal, inter nal, face g ro o ving and turning

rε
W

7˚ L
h

Insert W±0.05 W±0.002 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH7025 AH725 GH130 NS9530 (in) (in)
DTX3-030 3 3 0.118 0.012 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTX4-040 4 4 0.157 0.016 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTX5-040 5 5 0.197 0.016 䖃 䖃 䖃 䖃 䖃 0.984 0.217

DTX6-080 6 6 0.236 0.031 䖃 䖃 0.984 0.217

䖃 : Line up

Tungaloy C087
 DTF
Grooving Tool Face g ro ov ing a nd turning
rε

W
12˚ L
7˚
h

L1

Coated Cermet
Designation Insert T9125 AH725 GH130 NS9530
seat W±0.05 W±0.002 rε L h L1
size (mm) (in) (in) R L R L R L R L (in) (in) (in)
DTF3-040-R/L 3 3 0.118 0.016 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0.630

DTF4-040-R/L 4 4 0.157 0.016 䖃 䖃 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197 0.630

䖃 : Line up

DTI
Inter nal groo v ing and turning (fo r hig h-p recision m achining)

rε
W

14˚ L
h

Insert W±0.02 W±0.001 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH725 GH130 NS9530 (in) (in)
DTI300-040 3 3 0.118 0.016 䖃 䖃 䖃 䖃 0.787 0.197

DTI400-040 4 4 0.157 0.016 䖃 䖃 䖃 䖃 0.787 0.197

DTI400-080 4 4 0.157 0.031 䖃 䖃 䖃 䖃 0.787 0.197

DTI500-040 5 5 0.197 0.016 䖃 䖃 䖃 䖃 0.984 0.217

DTI500-080 5 5 0.197 0.031 䖃 䖃 䖃 䖃 0.984 0.217

DTI600-080 6 6 0.236 0.031 䖃 䖃 䖃 0.984 0.217

DTI600-120 6 6 0.236 0.047 䖃 䖃 䖃 0.984 0.217

DTI800-080 8 8 0.315 0.031 䖃 䖃 䖃 1.181 0.264

DTI800-120 8 8 0.315 0.047 䖃 䖃 䖃 1.181 0.264

䖃 : Line up

DTI
Inter nal groo v ing and turning

rε
W

14˚ L
h

Insert W±0.05 W±0.002 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH7025 AH725 GH130 NS9530 (in) (in)
DTI3-040 3 3 0.118 0.016 䖃 䖃 䖃 䖃 䖃 0.016 0.197

DTI4-040 4 4 0.118 0.016 䖃 䖃 䖃 䖃 0.016 0.197

䖃 : Line up

C088 www.tungaloyamerica.com
DG I M
Sm all d iameter internal g ro o ving

Grooving Tool
rε
W

14˚ L
h

Insert W±0.05 W±0.002 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH725 GH130 NS9530 (in) (in)
DGIM2-020 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197

䖃 : Line up

DG I S
Sm all d iameter internal g ro o ving

rε
W

14˚ L
h

Insert W±0.05 W±0.002 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH725 GH130 NS9530 (in) (in)
DGIS2-020 2 2 0.079 0.008 䖃 䖃 䖃 䖃 0.787 0.197

䖃 : Line up

DT R
Pro f iling and und ercutting (fo r hig h-p recisio n mac hining)

rε
W

7˚ L
h

Insert W±0.02 W±0.001 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH725 GH130 NS9530 (in) (in)
DTR300-150 3 3 0.118 0.059 䖃 䖃 䖃 䖃 0.787 0.197

DTR400-200 4 4 0.157 0.079 䖃 䖃 䖃 䖃 0.787 0.197

DTR478-239 5 4.78 0.188 0.094 䖃 䖃 䖃 䖃 0.984 0.217

DTR500-250 5 5 0.197 0.098 䖃 䖃 䖃 䖃 0.984 0.217

DTR600-300 6 6 0.236 0.118 䖃 䖃 䖃 0.984 0.217

䖃 : Line up

Tungaloy C089
 DTR
Grooving Tool Pro f iling and un dercutting

rε

W
7˚ L
h

Insert W±0.05 W±0.002 rε Coated Cermet L h

Designation seat
size (mm) (in) (in) T9125 AH7025 AH725 AH905 GH130 NS9530 (in) (in)
DTR3-150 3 3 0.118 0.059 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTR4-200 4 4 0.157 0.079 䖃 䖃 䖃 䖃 䖃 䖃 0.787 0.197

DTR5-250 5 5 0.197 0.098 䖃 䖃 䖃 䖃 䖃 䖃 0.984 0.217

DTR6-300 6 6 0.236 0.118 䖃 䖃 䖃 䖃 0.984 0.217

DTR8-400 8 8 0.315 0.157 䖃 䖃 䖃 1.181 0.264

䖃 : Line up

DTI U
Pro f iling and un dercutting (fo r hig h-precisio n m achining)

rε
W

14˚ L
h

Insert W±0.02 W±0.001 rε Coated L h

Designation seat
size (mm) (in) (in) AH725 GH130 (in) (in)
DTIU300-150 3 3 0.118 0.059 䖃 䖃 0.787 0.197

DTIU400-200 4 4 0.157 0.079 䖃 䖃 0.787 0.197

DTIU500-250 5 5 0.197 0.098 䖃 䖃 0.984 0.217

DTIU600-300 6 6 0.236 0.118 䖃 䖃 0.984 0.217

䖃 : Line up

DTA
A luminum w hee l machining (fo r hig h-precisio n m achining)

rε
W

A° L
h

Insert W±0.02 W±0.001 rε Uncoated L h

Designation seat A
size (mm) (in) (in) TH10 (in) (in)
DTA600-300 6 6 0.236 0.118 䖃 0.984 0.217 7º

DTA800-400 8 8 0.315 0.157 䖃 1.181 0.264 10º

䖃 : Line up

C090 www.tungaloyamerica.com
SGN
E xter nal g roo v ing o f hard ened steels

Grooving Tool
rε

W
7˚ L
h

Insert W±0.025 W±0.001 rε CBN L h

Designation seat
size (mm) (in) (in) BX360 (in) (in)
SGN200-020 2 2 0.079 0.008 䖃 0.787 0.197

SGN300-020 3 3 0.118 0.008 䖃 0.787 0.197

SGN400-020 4 4 0.157 0.008 䖃 0.787 0.197

䖃 : Line up

STA NDA RD CUT TING CONDITIONS

Cutting
ISO Workpiece material Hardness Priority Grade speed
Vc (sfm)
< 300 HB First choice AH7025, AH725 160 - 600

Steel < 300 HB Priority for wear resistance T9125 260 - 660
(1045, 4135, etc.) < 300 HB Priority for impact resistance GH130 160 - 400

< 300 HB Priority for surface finish NS9530 260 - 720

Stainless steel < 200 HB First choice AH7025, AH725 160 - 400
(304SS, 316SS, 17-4 PH, etc.) < 200 HB Priority for impact resistance GH130 160 - 400

Gray cast iron

- First choice GH130 160 - 600
(Class 25, Class 30, etc.)

Ductile cast iron

- First choice GH130 160 - 400
(60-40-18, 60-55-06, etc.)

Aluminum alloys
- First choice TH10 330 - 1650
(Si < 12%)

Titanium alloys < HRC 40 First choice AH905 60 - 260

(Ti-6Al-4V, etc.) < HRC 40 AH7025, AH725 60 - 260
Priority for impact resistance

Hardened material > HRC 50 First choice BX360 260 - 500

Tungaloy C091
 Grooving Tool
- Q uick Guide

Wide variety of tools dramatically reduce

set up time
2 3 4
1
5

14
13

12 11 10 9

External

1 CCH 2 CGSSR/L-D 3 CGSSR/L 4 CGWSR/L-G 5 CGWTR/L-G

1 corner 1 corner 1 corner 1 corner 1 corner
Internal Adaptor type
W = 0.118" - 0.197" Monoblock type Monoblock type Adaptor type
(3 - 5 mm) W = 0.118" - 0.197" W = 0.080" - 0.197" W = 0.080" - 0.197" W = 0.080" - 0.197"
Max. parting Dia.: 4.724" (3 - 5 mm) (2 - 5 mm) (2 - 5 mm) (2 - 5 mm)
(120 mm) ar = 0.866" - 1.000" ar = 0.472" - 0.630" ar = 0.472" (12 mm) ar = 0.472" (12 mm)
Shank size: 0.750" - 1.26" (22 - 25 mm) (12 - 16 mm) Shank size: 0.750" - 1.000" Shank size: 0.750" - 1.000"
Face
Grooving (20 - 32 mm) Shank size: 0.625" - 1.000" Shank size: 0.625" - 1.000" (20 - 25 mm) (20 - 25 mm)
Page C103 (16 - 25 mm) (16 - 25 mm) Page C100 Page C101
Page C102 Page C101

Parting-off
6 CGWSR/L 7 CGTR/L 8 CGWTR/L 9 CGWSR/L-WG 10 CGWSR/L-W
1 corner 2 corner 2 corner
*S/D*L/R Monoblock type *S/D*L/R Adaptor type Monoblock type
Others W = 0.118" - 0.197" W = 0.118" - 0.197" W = 0.118" - 0.197"
1 corner (3 - 5 mm) 1 corner (3 - 5 mm) (3 - 5 mm)
Adaptor type ar = 0.138" - 0.236" Adaptor type ar = 0.472" - 0.512" ar = 0.472" - 0.512"
W = 0.118" - 0.197" (3.5 - 6 mm) W = 0.118" - 0.197" (12 - 13 mm) (12 - 13 mm)
(3 - 5 mm) Shank size: 1.000" - 1.575" (3 - 5 mm) Shank size: 0.750" - 1.000" Shank size: 0.625" - 1.000"
ar = 0.394" - 0.866 (25 - 40 mm) ar = 0.394" - 0.866 (20 - 25 mm) (16 - 25 mm)
(10 - 22 mm) Page C111 (10 - 22 mm) Page C094 Page C093
Shank size: 0.750" - 1.000" Shank size: 0.750" - 1.000"
(20 - 25 mm) (20 - 25 mm)
Page C106 Page C108

11 CGWSR/L 12 CGWSR/L 13 CCH-W 14 JCGSSR/L

2 corner 1 corner
-WG-L -W-L W = 0.080" - 0.197"
(2 - 5 mm)
For swiss type machine
2 corner 2 corner W = 0.080" (2 mm)
Adaptor type Max. parting Dia.: 1.654" Max. parting Dia.: 1.260"
Monoblock type (42 mm)
W = 0.080" - 0.197" W = 0.118" - 0.197" (32 mm)
(2 - 5 mm) Shank size: 0.750" - 1.26" Shank size: 0.394"- 0.625"
(3 - 5 mm) (20 - 32 mm)
ar = 0.591" - 0.846" ar = 0.591" - 0.846" (10 - 16 mm)
(15 - 21.5 mm) Page C097 Page C102
(15 - 21.5 mm)
Shank size: 0.750" - 1.000" Shank size: 0.625" - 1.000"
(20 - 25 mm) (16 - 25 mm)
Page C094 Page C093

C092 www.tungaloyamerica.com
CG W S R /L-W

Grooving Tool
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
f
L1

w
L2

h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
CGWSR/L1616-W30 3 12 16 16 125 34 16 16.4 WG*30, WGE30R/L
CGWSR/L2020-W30 3 12 20 20 150 34 20 20.4 WG*30, WGE30R/L
CGWSR/L2525-W30 3 12 25 25 150 34 25 25.4 WG*30, WGE30R/L
CGWSR/L2020-W40 4 13 20 20 150 39 20 20.4 WG*40, WGE40R/L
CGWSR/L2525-W40 4 13 25 25 150 39 25 25.4 WG*40, WGE40R/L
CGWSR/L2020-W50 5 13 20 20 150 39 20 20.4 WG*50, WGE50R/L
CGWSR/L2525-W50 5 13 25 25 150 39 25 25.4 WG*50, WGE50R/L

SPARE PARTS
Designation Clamping screw Wrench
CGWSR/L****-W... CHHM5-18 P-4

CG W S R /L-W -L
E x te r n a l to o l h o l d e r s f o r d e e p g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
f

L1
w

External
L2
h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
CGWSR/L1616-W20-L 2 15 16 16 125 37 16 16.2 WGE20, WGE20R/L
CGWSR/L2020-W20-L 2 15 20 20 150 37 20 20.2 WGE20, WGE20R/L
CGWSR/L2525-W20-L 2 15 25 25 150 37 25 25.2 WGE20, WGE20R/L
CGWSR/L1616-W30-L 3 16.5, 17.5 16 16 125 37 16 16.4 WG*30, WGE30R/L
CGWSR/L2020-W30-L 3 16.5, 17.5 20 20 150 37 20 20.4 WG*30, WGE30R/L Parting-off

CGWSR/L2525-W30-L 3 16.5, 17.5 25 25 150 37 25 25.4 WG*30, WGE30R/L

Others
CGWSR/L2020-W40-L 4 21, 21.5 20 20 150 42 20 20.4 WG*40, WGE40R/L
CGWSR/L2525-W40-L 4 21, 21.5 25 25 150 42 25 25.4 WG*40, WGE40R/L
CGWSR/L2020-W50-L 5 21 20 20 150 42 20 20.4 WG*50, WGE50R/L
CGWSR/L2525-W50-L 5 21 25 25 150 42 25 25.4 WG*50, WGE50R/L

SPARE PARTS
Designation Clamping screw Wrench
CGWSR/L****-W**-L CHHM5-18 P-4

Reference pages
Inserts → C098 - C099, Standard cutting conditions → C099

Tungaloy C093
 Grooving Tool C G W S R /L-W G
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
f
w
L2 L1

h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert Shank Blade*

CGWSR/L2020-W30GR/L 3 12 20 20 150.5 43.5 20 26.9 WG*30, WGE30R/L CGWSR/L2020 W30GR/L
CGWSR/L2525-W30GR/L 3 12 25 25 150.5 43.5 25 31.9 WG*30, WGE30R/L CGWSR/L2525 W30GR/L
CGWSR/L2020-W40GR/L 4 13 20 20 151.5 44.5 20 26.9 WG*40, WGE40R/L CGWSR/L2020 W40GR/L
CGWSR/L2525-W40GR/L 4 13 25 25 151.5 44.5 25 31.9 WG*40, WGE40R/L CGWSR/L2525 W40GR/L
CGWSR/L2020-W50GR/L 5 13 20 20 151.5 44.5 20 26.9 WG*50, WGE50R/L CGWSR/L2020 W50GR/L
CGWSR/L2525-W50GR/L 5 13 25 25 151.5 44.5 25 31.9 WG*50, WGE50R/L CGWSR/L2525 W50GR/L
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWSR/L****-W**GR/L CHHM5-18 CSHB-6 P-4

C G W S R /L-W G - L
E x te r n a l to o l h o l d e r s f o r d e e p g ro o v i n g & p a r t i n g & t u r n i n g

ar
External

b
f

L2
w

L1
h1

Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert Shank Blade*

CGWSR/L2020-W20GR/L-L 2 15 20 20 153.5 46.5 20 26.7 WGE20, WGE20R/L CGWSR/L2020 W20GR/L-L
CGWSR/L2525-W20GR/L-L 2 15 25 25 153.5 46.5 25 31.7 WGE20, WGE20R/L CGWSR/L2525 W20GR/L-L
Parting-off CGWSR/L2020-W30GR/L-L 3 16.5 - 17.5 20 20 157.5 50.5 20 26.9 WG*30, WGE30R/L CGWSR/L2020 W30GR/L-L
CGWSR/L2525-W30GR/L-L 3 16.5 - 17.5 25 25 157.5 50.5 25 31.9 WG*30, WGE30R/L CGWSR/L2525 W30GR/L-L
Others CGWSR/L2020-W40GR/L-L 4 21 - 21.5 20 20 162.5 55.5 20 26.9 WG*40, WGE40R/L CGWSR/L2020 W40GR/L-L
CGWSR/L2525-W40GR/L-L 4 21 - 21.5 25 25 162.5 55.5 25 31.9 WG*40, WGE40R/L CGWSR/L2525 W40GR/L-L
CGWSR/L2020-W50GR/L-L 5 21 20 20 162.5 55.5 20 26.9 WG*50, WGE50R/L CGWSR/L2020 W50GR/L-L
CGWSR/L2525-W50GR/L-L 5 21 25 25 162.5 55.5 25 31.9 WG*50, WGE50R/L CGWSR/L2525 W50GR/L-L
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWSR/L****-W**GR/L-L CHHM5-18 CSHB-6 P-4

Reference pages
Inserts → C098 - C099, Standard cutting conditions → C099

C094 www.tungaloyamerica.com
CG W S R /L

Grooving Tool
Sha n k o f to o l h o l d er s C G W S R / L- W G , - W G - L, - G , - C G D, - F L- G / TP & - #S / D

b
L1

h
2-M6
Right hand (R) shown.

Inch h b L1
CGWSR/L12 0.75 0.75 5.40
CGWSR/L16 1.00 1.00 5.40

Metric h b L1
CGWSR/L2020 20 20 137
CGWSR/L2525 25 25 137
Note: Right hand tool holders (R) use right hand cartridges (R)
Left hand tool holders (L) use left hand cartridges (L)

SPARE PARTS
Designation Blade screw
CGWSR/L... CSHB-6

CG W S R L
S h a n k o f to o l h o l d e r s . Ve r t i c a l t y p e w i t h o f f s e t
b

L1
h

2-M6

Inch h b L1
CGWSRL12 0.75 0.75 5.40
CGWSRL16 1.00 1.00 5.40
Note: Right (R) or Left (L) hand cartridges can be used in this toolholder

SPARE PARTS
Designation Blade screw
CGWSRL... CSHB-6

Tungaloy C095
 C G W TR /L
Grooving Tool
Sh a n k o f p e r p end i cul ar to o l ho l d er s C G W T R / L- G , - C G D, - F L & - #S / D

2-M6

b
f1
45°
L1

h
Right hand (R) shown.

Inch h b L1 f1
CGWTR/L12 0.75 0.75 6.00 1.50
CGWTR/L16 1.00 1.00 6.00 1.50

Metric h b L1 f1
CGWTR/L2020 20 20 150 37
CGWTR/L2525 25 25 150 37
Note: Right hand tool holders (R) use left hand cartridges (L)
Left hand tool holders (L) use right hand cartridges (R)

SPARE PARTS
Designation Blade screw
CGWTR/L... CSHB-6

C096 www.tungaloyamerica.com
CC H -W

Grooving Tool
B l a d e s f o r ex te r n a l g ro o v i n g & p a r t i n g o f f ( 2 c o r n e r )

Wh 5.91"
150

h1
Inch W Applicable insert Max. parting off dia. Wh h1 h
CCH32-W20 0.079 WGE20, WGE20R/L 1.3 0.063 0.968 (1.26)
CCH32-W30 0.118 WG*30, WGE30R/L 1.3 0.087 0.968 (1.26)
CCH32-W40 0.157 WG*40, WGE40R/L 1.65 0.126 0.965 (1.26)
CCH32-W50 0.197 WG*50, WGE50R/L 1.65 0.165 0.965 (1.26)

CC B S-32
Too l b l o c k f o r CC H b l ad es

3.94"
100
CCH32...
h1

h1
h

L 4.33"
110
h2

Inch h h1 h2 L Blade*
CCBS12-32-U 0.75 0.75 0.55 1.49 CCH32...
CCBS16-32-U 1.00 1.00 0.30 1.66 CCH32...
CCBS20-32-U 1.25 1.25 0.21 1.66 CCH32... External
* Blade sold separately.

SPARE PARTS
Designation Clamp Screw Wrench
CCBS**-32-U CC-32 CM6X25 P-5

Parting-off

Reference pages
Inserts → C098 - C099, Standard cutting conditions → C099

Tungaloy C097
Grooving Tool
- Chipbreaker Guide
2 corner inserts
External grooving and parting off
WGE 1st choice for external 0.012
grooving and parting 0.010

Feed: f (ipr)
0.008
Excellent chip control for
0.006
grooving External
0.004
Internal
W = 0.078" - 0.196" 0.002 Face
Parting off
0.08 0.12 0.16 0.20
Groove width : W (in)

Page C099

Parting off
WGE R/L Handed insert 0.012
0.010

Feed: f (ipr)
Minimize burr generation when 0.008
workpiece is cut off
0.006
W = 0.078" - 0.196" 0.004
0.002

0.08 0.12 0.16 0.20

Groove width : W (in)
Page C099

External grooving and traversing

WGT 1st choice for traversing
WGT50
Depth of cut

0.008
Low cutting force and good WGT40
ap (in)

chip control for traversing 0.004 WGT30

W = 0.118" - 0.196"

0.002 0.004 0.006 0.008 0.010 0.012

Feed: f (ipr)

Page C099

Profiling
WGR Low cutting force and good
chip control for profiling
Depth of cut

0.008 WGR50
ap (in)

WGR40
W = 0.118" - 0.196" 0.004 WGR30

0.002 0.004 0.006 0.008 0.010 0.012

Feed: f (ipr)

Page C099

C098 www.tungaloyamerica.com
WG E W GT
For general parting off L For traversing rε L

Grooving Tool
and grooving rε

w
w

h
h
rε Coated LCermet h rε Coated Cermet
L h
Designation W +0.1 +0.004
0 W 0
+0.1 +0.004
Designation W 0 W 0
(mm) (in) (in) T9125 AH120 GH730 NS9530 (in) (in) (mm) (in) (in) T9125 GH730 NS9530 (in) (in)
WGE20 2 0.078 0.008 䖃 䖃 䖃 0.787 0.185 WGT30 3 0.118 0.016 䖃 䖃 䖃 0.787 0.216

WGE30 3 0.118 0.008 䖃 䖃 䖃 䖃 0.787 0.216 WGT40 4 0.157 0.016 䖃 䖃 䖃 0.984 0.224

WGE40 4 0.157 0.008 䖃 䖃 䖃 䖃 0.984 0.224 WGT50 5 0.196 0.016 䖃 䖃 䖃 0.984 0.232

WGE50 5 0.196 0.008 䖃 䖃 䖃 䖃 0.984 0.232 䖃 : Line up

䖃 : Line up

WG E R /L WGR
For parting off rε L For profiling rε L
(with hand)

w
w

8˚
h

h
Right hand (R) shown.

Coated +0.1 +0.004 rε Coated Cermet

L h
Designation W 0 W 0
Designation +0.1 +0.004 rε GH730 L h (mm) (in) (in) T9125 GH730 NS9530 (in) (in)
W 0 W 0
(mm) (in) (in) R L (in) (in) WGR30 3 0.118 0.059 䖃 䖃 䖃 0.787 0.216

WGE20R/L 2 0.078 0.008 䖃 䖃 0.787 0.185 WGR40 4 0.157 0.078 䖃 䖃 䖃 0.984 0.224

WGE30R/L 3 0.118 0.008 䖃 䖃 0.787 0.216 WGR50 5 0.196 0.098 䖃 䖃 0.984 0.232

WGE40R/L 4 0.157 0.008 䖃 䖃 0.984 0.224 䖃 : Line up

WGE50R/L 5 0.196 0.008 䖃 䖃 0.984 0.232

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS

Recommended Cutting speed Feed: f (ipr)
Workpiece material vc (sfm)
grade
Operation Groove width: W (in)
Low carbon steels T9125 260 ~ 650 2 (0.078") 3 (0.118") 4 (0.157") 5 (0.196")
Alloy steels NS9530 260 ~ 550
Grooving
( ~ HB150) GH730 160 ~ 590 0.002 ~ 0.008 0.002 ~ 0.009 0.003 ~ 0.011 0.003 ~ 0.012
(WGE䊐䊐)
Medium carbon steels T9125 260 ~ 590
Alloy steels NS9530 260 ~ 500
(HB150 ~ 250) Parting off
GH730 160 ~ 500 0.001 ~ 0.004 0.001 ~ 0.006 0.001 ~ 0.006 0.001 ~ 0.006
(WGE䊐䊐R/L)
High carbon steels T9125 260 ~ 500
Alloy steels NS9530 260 ~ 400
Traversing ap = 0.008 ~ 0.060 ap = 0.020 ~ 0.078 ap = 0.020 ~ 0.098
(HB250 ~ ) GH730 160 ~ 400 -
(WGT䊐䊐) f = 0.002 ~ 0.006 f = 0.002 ~ 0.009 f = 0.002 ~ 0.010
T9125 260 ~ 500
Stainless steels
GH730 160 ~ 400
Profiling ap = 0.020 ~ 0.055 ap = 0.008 ~ 0.060 ap = 0.020 ~ 0.062
Gray and T9125 260 ~ 650 -
(WGR䊐䊐) f = 0.002 ~ 0.010 f = 0.002 ~ 0.010 f = 0.002 ~ 0.012
ductile cast irons GH730 160 ~ 590
Note: For diameter compensation values in traversing, see page C118.

Tungaloy C099
 Grooving Tool C G W S R /L-G
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
w
f
L2 L1

h1

h
Right hand (R) shown.
The dashed line shows
46.65 0.787"-square shank tools.

Inch W ar h b L1 L2 h1 f Insert Shank Blade*

CGWSR/L12-20GR/L 0.079 0.472 0.750 0.750 5.913 1.699 0.787 1.055 GE20, GE20-AL CGWSR/L12 20GR/L
CGWSR/L16-20GR/L 0.079 0.472 1.000 1.000 5.913 1.699 0.984 1.252 GE20, GE20-AL CGWSR/L16 20GR/L
CGWSR/L12-30GR/L 0.118 0.472 0.750 0.750 5.913 1.699 0.787 1.063 G*30,GE30R/L,GE30-AL CGWSR/L12 30GR/L
CGWSR/L16-30GR/L 0.118 0.472 1.000 1.000 5.913 1.699 0.984 1.260 G*30,GE30R/L,GE30-AL CGWSR/L16 30GR/L
CGWSR/L12-40GR/L 0.157 0.472 0.750 0.750 5.913 1.699 0.787 1.067 G*40,GE40R/L,GE40-AL CGWSR/L12 40GR/L
CGWSR/L16-40GR/L 0.157 0.472 1.000 1.000 5.913 1.699 0.984 1.264 G*40,GE40R/L,GE40-AL CGWSR/L16 40GR/L
CGWSR/L12-50GR/L 0.197 0.472 0.750 0.750 5.913 1.699 0.787 1.071 G*50,GE50R CGWSR/L12 50GR

Metric W ar h b L1 L2 h1 f Insert Shank Blade*

CGWSR/L2020-20GR/L 2 12 20 20 150.2 43.15 20 26.8 GE20, GE20-AL CGWSR/L2020 20GR/L
CGWSR/L2525-20GR/L 2 12 25 25 150.2 43.15 25 31.8 GE20, GE20-AL CGWSR/L2525 20GR/L
CGWSR/L2020-30GR/L 3 12 20 20 150.2 43.15 20 27 G*30,GE30R/L,GE30-AL CGWSR/L2020 30GR/L
CGWSR/L2525-30GR/L 3 12 25 25 150.2 43.15 25 32 G*30,GE30R/L,GE30-AL CGWSR/L2525 30GR/L
CGWSR/L2020-40GR/L 4 12 20 20 150.2 43.15 20 27.1 G*40,GE40R/L,GE40-AL CGWSR/L2020 40GR/L
CGWSR/L2525-40GR/L 4 12 25 25 150.2 43.15 25 32.1 G*40,GE40R/L,GE40-AL CGWSR/L2525 40GR/L
CGWSR/L2020-50GR/L 5 12 20 20 150.2 43.15 20 27.2 G*50,GE50R CGWSR/L2020 50GR
Note: For diameter compensation values in traversing, see page C118.
When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
External
CGWSR/L****-**GR/L CHHM5-18 CSHB-6 P-4

Parting-off

Others

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

C100 www.tungaloyamerica.com
CG W TR /L-G

Grooving Tool
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

L2

b
f

ar
W L1
Right hand (R) shown.
The dashed line shows

h
0.787"-square shank tools.

Inch W ar h b L1 L2 f Insert Shank Blade*

CGWTR/L12-30GL/R 0.118 0.472 0.750 0.750 5.911 0.508 1.960 G*30,GE30R/L,GE30-AL CGWTR/L12 30GL/R
CGWTR/L16-30GL/R 0.118 0.472 1.000 1.000 5.911 0.508 1.960 G*30,GE30R/L,GE30-AL CGWTR/L16 30GL/R
CGWTR/L12-40GL/R 0.157 0.472 0.750 0.750 5.911 0.508 1.960 G*40,GE40R/L,GE40-AL CGWTR/L12 40GL/R
CGWTR/L16-40GL/R 0.157 0.472 1.000 1.000 5.911 0.508 1.960 G*40,GE40R/L,GE40-AL CGWTR/L16 40GL/R
CGWTR/L12-50GL/R 0.197 0.472 0.750 0.750 5.911 0.508 1.960 G*50,GE50R/L,GE50-AL CGWTR/L12 50GL/R
CGWTR/L16-50GL/R 0.197 0.472 1.000 1.000 5.911 0.508 1.960 G*50,GE50R/L,GE50-AL CGWTR/L16 50GL/R

Metric W ar h b L1 L2 f Insert Shank Blade*

CGWTR/L2020-30GL/R 3 12 20 20 150 12.9 49.9 G*30,GE30R/L,GE30-AL CGWTR/L2020 30GL/R
CGWTR/L2525-30GL/R 3 12 25 25 150 12.9 49.9 G*30,GE30R/L,GE30-AL CGWTR/L2525 30GL/R
CGWTR/L2020-40GL/R 4 12 20 20 150.1 12.9 49.9 G*40,GE40R/L,GE40-AL CGWTR/L2020 40GL/R
CGWTR/L2525-40GL/R 4 12 25 25 150.1 12.9 49.9 G*40,GE40R/L,GE40-AL CGWTR/L2525 40GL/R
CGWTR/L2020-50GL/R 5 12 20 20 150.2 12.9 49.9 G*50,GE50R/L,GE50-AL CGWTR/L2020 50GL/R
CGWTR/L2525-50GL/R 5 12 25 25 150.2 12.9 49.9 G*50,GE50R/L,GE50-AL CGWTR/L2525 50GL/R
Note: For diameter compensation values in traversing, see page C118.
When using a right or left hand blade set, the right hand blade set is used with left hand shank and the left hand blade set is used with right hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWTR/L****-**GL/R CHHM5-18 CSHB-6 P-4

CG S S R /L
External
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

ar
w

b
f

L1
L2
h1

Right hand (R) shown.

Parting-off
Metric W ar h b L1 L2 h1 f Insert
CGSSR/L1616-20 2 16 16 16 125 27 16 16.2 GE20, GE20-AL Others
CGSSR/L2020-20 2 16 20 20 150 27 20 20.2 GE20, GE20-AL
CGSSR/L2525-20 2 16 25 25 150 27 25 25.2 GE20, GE20-AL
CGSSR/L1616-30 3 12 16 16 125 27 16 16.5 G*30,GE30R/L,GE30-AL
CGSSR/L2020-30 3 12 20 20 150 27 20 20.5 G*30,GE30R/L,GE30-AL
CGSSR/L2525-30 3 12 25 25 150 27 25 25.5 G*30,GE30R/L,GE30-AL
CGSSR/L2020-40 4 12 20 20 150 27 20 20.6 G*40,GE40R/L,GE40-AL
CGSSR/L2525-40 4 12 25 25 150 27 25 25.6 G*40,GE40R/L,GE40-AL
CGSSR/L2020-50 5 12 20 20 150 27 20 20.7 G*50,GE50R/L,GE50-AL
CGSSR/L2525-50 5 12 25 25 150 27 25 25.7 G*50,GE50R/L,GE50-AL

SPARE PARTS
Designation Clamping screw Wrench
CGSSR/L... CHHM5-18 P-4

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

Tungaloy C101
 C G S S R /L-D
Grooving Tool
E x te r n a l to o l h o l d e r s f o r d e e p g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
f
L1

w
L2

h1

h
Right hand (R) shown.

Metric W ar h b L1 L2 h1 f Insert
CGSSR/L1616-30D 3 22 16 16 125 36.2 16 16.5 G*30,GE30R/L,GE30-AL
CGSSR/L2020-30D 3 22 20 20 150 36.2 20 20.5 G*30,GE30R/L,GE30-AL
CGSSR/L2525-30D 3 22 25 25 150 36.2 25 25.5 G*30,GE30R/L,GE30-AL
CGSSR/L2020-40D 4 25 20 20 150 39.5 20 20.6 G*40,GE40R/L,GE40-AL
CGSSR/L2525-40D 4 25 25 25 150 39.5 25 25.6 G*40,GE40R/L,GE40-AL
CGSSR/L2020-50D 5 25 20 20 150 39.5 20 20.7 G*50,GE50R/L
CGSSR/L2525-50D 5 25 25 25 150 39.5 25 25.7 G*50,GE50R/L

SPARE PARTS
Designation Clamping screw Wrench
CGSSR/L****-**D CHHM5-18 P-4

JC G SSR /L
E x te r n a l g ro o v i ng to o l ho l d er s f o r sw i ss l a t h e

b
f
W

External
øDmax L1
L2
h1

h
Right hand (R) shown.

Metric W øDmax h b L1 L2 h1 f Insert

JCGSSR/L1010-20 2 20 10 10 125 15 10 10.2 GE20, GE20-AL
JCGSSR/L1212-20 2 25 12 12 125 19 12 12.2 GE20, GE20-AL
JCGSSR/L1616-20 2 32 16 16 125 22.5 16 16.2 GE20, GE20-AL
Parting-off • øDmax: Max. parting off diameter.

Others SPARE PARTS

Designation Clamping screw Wrench
JCGSSR/L... CSTB-3 T-9F

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

C102 www.tungaloyamerica.com
CC H

Grooving Tool
B l a d e s f o r ex te r n a l g ro o v i n g & p a r t i n g o f f ( f o r 1 c o r n e r i n s e r t )

W
b 5.91"
150
øDmax

B1

h1
Inch W øDmax b h1 B1 Insert
CCH26-30 0.118 2.76 0.087 0.843 0.979 GE30,GE30R/L,GE30-AL
CCH26-40 0.157 2.76 0.126 0.837 0.968 GE40,GE40R/L,GE40-AL
CCH32-30U 0.118 3.94 0.087 0.968 1.230 GE30,GE30R/L,GE30-AL
CCH32-40U 0.157 3.94 0.126 0.963 1.220 GE40,GE40R/L,GE40-AL
CCH32-50U 0.197 4.72 0.165 0.958 1.210 GE50,GE50R/L,GE50-AL
• øDmax: Max. parting off diameter

SPARE PARTS
Designation Wrench
CCH... CTL-2

CC B S-32
Too l b l o c k f o r CC H b l ad es

3.94"
100
CCH32...
h1

h1
h

L 4.33"
110
h2

External

Inch h h1 h2 L Blade
CCBS12-32-U 0.750 0.75 0.55 1.49 CCH32...
CCBS16-32-U 1.000 1.00 0.30 1.66 CCH32...
CCBS20-32-U 1.250 1.25 0.21 1.66 CCH32...

SPARE PARTS
Designation Clamp Screw Wrench
CCBS**-32-U CC-32 CM6X25 P-5
Parting-off

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

Tungaloy C103
Grooving Tool CTB U
To o l b l o c k f o r C G P and E G P b l ad es

B1

h4
b

h1

h
L2 L1

h2
L3 Right hand (R) shown.

Inch h1 b B1 L1 h h2 h4 L2 L3 Blade*
CTBU12-26-U 0.843 0.157 1.024 3.386 0.750 0.354 1.693 0.827 1.496 CGP26..., CCH26...
CTBU16-26-U 0.843 0.157 1.024 4.331 1.000 0.197 1.772 0.906 1.654 CGP26..., CCH26...
CTBU12-32-U 0.976 0.209 1.260 3.937 0.750 0.512 1.969 0.748 1.496 CGP32..., CCH32...
CTBU16-32-U 0.976 0.209 1.260 4.331 1.000 0.315 1.969 0.906 1.654 CGP32..., CCH32...
CTBU20-32-U 0.976 0.209 1.260 4.331 1.250 0.197 2.126 1.142 1.890 CGP32..., CCH32...

Metric h1 b B1 L1 h h2 h4 L2 L3 Blade*
CTBU20-26 21.4 4 26 86 20 9 43 21 38 CGP26..., CCH26...
CTBU25-26 21.4 4 26 110 25 5 45 23 42 CGP26..., CCH26...
CTBU20-32 24.8 5.3 32 100 20 13 50 19 38 CGP32..., CCH32...
CTBU25-32 24.8 5.3 32 110 25 8 50 23 42 CGP32..., CCH32...
CTBU32-32 24.8 5.3 32 110 32 5 54 29 48 CGP32..., CCH32...
* Blade sold separately.

SPARE PARTS
Designation Clamp Clamping screw Wrench
CTBU12-26-U,
CT-86 CM6X30-S P-5
CTBU20-26
CTBU12-32-U,
CT-105 CM6X30-S P-5
CTBU25-26
CTBU16-26-U,
CT-100 CM6X30-S P-5
CTBU20-32
CTBU16-32-U,
CT-110 CM6X30-S P-5
CTBU25-32
CTBU20-32-U,
CT-110 CM6X30-S P-5
CTBU32-32

C104 www.tungaloyamerica.com
 Grooving Tool
MEMO

Tungaloy C105
 Grooving Tool #S /D ##R /L+CG WSR/L
Bl a d e s o f "M y -T " to o l ho l d er s C G W S R / L- # S / D & C G W TR / L- #S / D f or f a c e groov i n g & t u r n i n g

ar Right hand CGWSR****-****R Left hand CGWSL****-***L

b
f
L1 øDm Reverse rotation
øDmax
Regular rotation

h1

h
Right hand (R) shown. Shank: Right hand Shank: Left hand
The dashed line shows 0.787" square shank tools. Blade: Right hand Blade: Left hand

Inch W øDm øDmax ar h b L1 h1 f Insert Shank

30S3040R/L 0.118 1.181 1.575 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
30S4050R/L 0.118 1.575 1.696 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
30S5065R/L 0.118 1.696 2.559 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
30S6590R/L 0.118 2.559 3.543 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
30S90150R/L 0.118 3.543 5.906 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
30S150500R/L 0.118 5.906 19.685 0.393 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*30, GE30-AL CGWSR/L12, 16
40S3545R/L 1.157 1.378 1.772 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40S4555R/L 1.157 1.772 2.165 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40S5580R/L 1.157 2.165 3.150 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40S80140R/L 1.157 3.150 5.512 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40S140500R/L 1.157 5.512 19.685 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40D3545R/L 1.157 1.378 1.772 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40D4555R/L 1.157 1.772 2.165 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40D5580R/L 1.157 2.165 3.150 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40D80140R/L 1.157 3.150 5.512 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
40D140500R/L 1.157 5.512 19.685 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*40, GE40-AL CGWSR/L12, 16
50S3545R/L 0.197 1.378 1.772 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50S4555R/L 0.197 1.772 2.165 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50S5575R/L 0.197 2.165 2.953 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50S75130R/L 0.197 2.953 5.118 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50S130500R/L 0.197 5.118 19.685 0.551 0.750/1.0 0.750/1.0 6.004 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50D3545R/L 0.197 1.378 1.772 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50D4555R/L 0.197 1.772 2.165 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50D5575R/L 0.197 2.165 2.953 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50D75130R/L 0.197 2.953 5.118 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
50D130500R/L 0.197 5.118 19.685 0.866 0.750/1.0 0.750/1.0 6.319 0.750/1.0 1.063/1.260 G*50 CGWSR/L12, 16
• There are 2 shank type of CGWSR/L and CGWTR/L.
• CGWSR/L Shank : The right hand blade set(...R) is used with right hand shank(CGWSR...) and the left hand blade set(...L) is used with left hand shank(CGWSL...).
Face
• CGWTR/L Shank : The left hand blade set(...L)is used with right hand shank(CGWTR...) and the right hand blade set(...R)is used with left hand shank(CGWTL...).
Grooving

SPARE PARTS
Designation Clamping screw Blade screw Wrench
30S..., 40S... CHHM5-18 CSHB-6 P-4
40D... CM5X0.8X16 CSHB-6 P-4
Others 50S... CHHM5-18 CSHB-6 P-4
50D... CM5X0.8X16 CSHB-6 P-4

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

C106 www.tungaloyamerica.com
 Grooving Tool
Metric W øDm øDmax ar h b L1 h1 f Insert Shank
30S3040R/L 3 30 40 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
30S4050R/L 3 40 50 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
30S5065R/L 3 50 65 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
30S6590R/L 3 65 90 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
30S90150R/L 3 90 150 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
30S150500R/L 3 150 500 10 20/25 20/25 152.5 20/25 27/32 G*30, GE30-AL CGWSR/L2020, 2525
40S3545R/L 4 35 45 14 20/25 20/25 152.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40S4555R/L 4 45 55 14 20/25 20/25 152.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40S5580R/L 4 55 80 14 20/25 20/25 152.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40S80140R/L 4 80 140 14 20/25 20/25 152.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40S140500R/L 4 140 500 14 20/25 20/25 152.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40D3545R/L 4 35 45 22 20/25 20/25 160.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40D4555R/L 4 45 55 22 20/25 20/25 160.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40D5580R/L 4 55 80 22 20/25 20/25 160.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40D80140R/L 4 80 140 22 20/25 20/25 160.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
40D140500R/L 4 140 500 22 20/25 20/25 160.5 20/25 27/32 G*40, GE40-AL CGWSR/L2020, 2525
50S3545R/L 5 35 45 14 20/25 20/25 152.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50S4555R/L 5 45 55 14 20/25 20/25 152.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50S5575R/L 5 55 75 14 20/25 20/25 152.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50S75130R/L 5 75 130 14 20/25 20/25 152.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50S130500R/L 5 130 500 14 20/25 20/25 152.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50D3545R/L 5 35 45 22 20/25 20/25 160.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50D4555R/L 5 45 55 22 20/25 20/25 160.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50D5575R/L 5 55 75 22 20/25 20/25 160.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50D75130R/L 5 75 130 22 20/25 20/25 160.5 20/25 27/32 G*50 CGWSR/L2020, 2525
50D130500R/L 5 130 500 22 20/25 20/25 160.5 20/25 27/32 G*50 CGWSR/L2020, 2525
• There are 2 shank type of CGWSR/L and CGWTR/L.
• CGWSR/L Shank : The right hand blade set(...R) is used with right hand shank(CGWSR...) and the left hand blade set(...L) is used with left hand shank(CGWSL...).
• CGWTR/L Shank : The left hand blade set(...L)is used with right hand shank(CGWTR...) and the right hand blade set(...R)is used with left hand shank(CGWTL...). Face
Grooving

SPARE PARTS
Designation Clamping screw Blade screw Wrench
30S..., 40S... CHHM5-18 CSHB-6 P-4
40D... CM5X0.8X16 CSHB-6 P-4
50S... CHHM5-18 CSHB-6 P-4 Others
50D... CM5X0.8X16 CSHB-6 P-4

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

Tungaloy C107
 Grooving Tool #S /D ##R /L+CG WT R/L
Bl a d e s o f "M y -T " to o l ho l d er s C G W S R / L- # S / D & C G W TR / L- #S / D f or f a c e groov i n g & t u r n i n g

Right hand CGWTR****-***L Left hand CGWTL****-***R

ar

b
f
W L1 øDm Reverse rotation

h1
øDmax Regular rotation

h
Right hand (R) shown.
The dashed line shows 0.787” Shank: Right hand Shank: Left hand
square shank tools. Blade: Left hand Blade: Right hand

Inch W øDm øDmax ar h b L1 h1 f Insert Shank

30S3040R/L 0.118 1.181 1.575 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
30S4050R/L 0.118 1.575 1.696 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
30S5065R/L 0.118 1.696 2.559 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
30S6590R/L 0.118 2.559 3.543 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
30S90150R/L 0.118 3.543 5.906 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
30S150500R/L 0.118 5.906 19.685 0.393 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*30, GE30-AL CGWSR/L12, 16
40S3545R/L 0.157 1.378 1.772 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*40, GE40-AL CGWSR/L12, 16
40S4555R/L 0.157 1.772 2.165 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*40, GE40-AL CGWSR/L12, 16
40S5580R/L 0.157 2.165 3.150 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*40, GE40-AL CGWSR/L12, 16
40S80140R/L 0.157 3.150 5.512 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*40, GE40-AL CGWSR/L12, 16
40S140500R/L 0.157 5.512 19.685 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*40, GE40-AL CGWSR/L12, 16
40D3545R/L 0.157 1.378 1.772 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*40, GE40-AL CGWSR/L12, 16
40D4555R/L 0.157 1.772 2.165 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*40, GE40-AL CGWSR/L12, 16
40D5580R/L 0.157 2.165 3.150 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*40, GE40-AL CGWSR/L12, 16
40D80140R/L 0.157 3.150 5.512 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*40, GE40-AL CGWSR/L12, 16
40D140500R/L 0.157 5.512 19.685 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*40, GE40-AL CGWSR/L12, 16
50S3545R/L 0.197 1.378 1.772 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*50 CGWSR/L12, 16
50S4555R/L 0.197 1.772 2.165 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*50 CGWSR/L12, 16
50S5575R/L 0.197 2.165 2.953 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*50 CGWSR/L12, 16
50S75130R/L 0.197 2.953 5.118 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*50 CGWSR/L12, 16
50S130500R/L 0.197 5.118 19.685 0.551 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.057 G*50 CGWSR/L12, 16
50D3545R/L 0.197 1.378 1.772 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*50 CGWSR/L12, 16
50D4555R/L 0.197 1.772 2.165 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*50 CGWSR/L12, 16
50D5575R/L 0.197 2.165 2.953 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*50 CGWSR/L12, 16
50D75130R/L 0.197 2.953 5.118 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*50 CGWSR/L12, 16
50D130500R/L 0.197 5.118 19.685 0.866 0.750/1.0 0.750/1.0 5.906 0.750/1.0 2.372 G*50 CGWSR/L12, 16
• There are 2 shank type of CGWSR/L and CGWTR/L.
• CGWSR/L Shank : The right hand blade set(...R) is used with right hand shank(CGWSR...) and the left hand blade set(...L) is used with left hand shank(CGWSL...).
Face
• CGWTR/L Shank : The left hand blade set(...L)is used with right hand shank(CGWTR...) and the right hand blade set(...R)is used with left hand shank(CGWTL...).
Grooving

SPARE PARTS
Designation Clamping screw Blade screw Wrench
30S..., 40S... CHHM5-18 CSHB-6 P-4
40D... CM5X0.8X16 CSHB-6 P-4
Others 50S... CHHM5-18 CSHB-6 P-4
50D... CM5X0.8X16 CSHB-6 P-4

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

C108 www.tungaloyamerica.com
 Grooving Tool
Metric W øDm øDmax ar h b L1 h1 f Insert Shank
30S3040R/L 3 30 40 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
30S4050R/L 3 40 50 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
30S5065R/L 3 50 65 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
30S6590R/L 3 65 90 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
30S90150R/L 3 90 150 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
30S150500R/L 3 150 500 10 20/25 20/25 150 20/25 52.25 G*30, GE30-AL CGWSR/L2020, 2525
40S3545R/L 4 35 45 14 20/25 20/25 150 20/25 52.25 G*40, GE40-AL CGWSR/L2020, 2525
40S4555R/L 4 45 55 14 20/25 20/25 150 20/25 52.25 G*40, GE40-AL CGWSR/L2020, 2525
40S5580R/L 4 55 80 14 20/25 20/25 150 20/25 52.25 G*40, GE40-AL CGWSR/L2020, 2525
40S80140R/L 4 80 140 14 20/25 20/25 150 20/25 52.25 G*40, GE40-AL CGWSR/L2020, 2525
40S140500R/L 4 140 500 14 20/25 20/25 150 20/25 52.25 G*40, GE40-AL CGWSR/L2020, 2525
40D3545R/L 4 35 45 22 20/25 20/25 150 20/25 60.25 G*40, GE40-AL CGWSR/L2020, 2525
40D4555R/L 4 45 55 22 20/25 20/25 150 20/25 60.25 G*40, GE40-AL CGWSR/L2020, 2525
40D5580R/L 4 55 80 22 20/25 20/25 150 20/25 60.25 G*40, GE40-AL CGWSR/L2020, 2525
40D80140R/L 4 80 140 22 20/25 20/25 150 20/25 60.25 G*40, GE40-AL CGWSR/L2020, 2525
40D140500R/L 4 140 500 22 20/25 20/25 150 20/25 60.25 G*40, GE40-AL CGWSR/L2020, 2525
50S3545R/L 5 35 45 14 20/25 20/25 150 20/25 52.25 G*50 CGWSR/L2020, 2525
50S4555R/L 5 45 55 14 20/25 20/25 150 20/25 52.25 G*50 CGWSR/L2020, 2525
50S5575R/L 5 55 75 14 20/25 20/25 150 20/25 52.25 G*50 CGWSR/L2020, 2525
50S75130R/L 5 75 130 14 20/25 20/25 150 20/25 52.25 G*50 CGWSR/L2020, 2525
50S130500R/L 5 130 500 14 20/25 20/25 150 20/25 52.25 G*50 CGWSR/L2020, 2525
50D3545R/L 5 35 45 22 20/25 20/25 150 20/25 60.25 G*50 CGWSR/L2020, 2525
50D4555R/L 5 45 55 22 20/25 20/25 150 20/25 60.25 G*50 CGWSR/L2020, 2525
50D5575R/L 5 55 75 22 20/25 20/25 150 20/25 60.25 G*50 CGWSR/L2020, 2525
50D75130R/L 5 75 130 22 20/25 20/25 150 20/25 60.25 G*50 CGWSR/L2020, 2525
50D130500R/L 5 130 500 22 20/25 20/25 150 20/25 60.25 G*50 CGWSR/L2020, 2525
• There are 2 shank type of CGWSR/L and CGWTR/L.
• CGWSR/L Shank : The right hand blade set(...R) is used with right hand shank(CGWSR...) and the left hand blade set(...L) is used with left hand shank(CGWSL...).
• CGWTR/L Shank : The left hand blade set(...L)is used with right hand shank(CGWTR...) and the right hand blade set(...R)is used with left hand shank(CGWTL...). Face
Grooving

SPARE PARTS
Designation Clamping screw Blade screw Wrench
30S..., 40S... CHHM5-18 CSHB-6 P-4
40D... CM5X0.8X16 CSHB-6 P-4
Others
50S... CHHM5-18 CSHB-6 P-4
50D... CM5X0.8X16 CSHB-6 P-4

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

Tungaloy C109
Grooving Tool C G W S R /L
Sh a n k o f to o l ho l d er s C G W S R / L- W G , - W G - L , - G , - C G D, - F L- G / TP & - #S / D

b
L1

h
2-M6
Right hand (R) shown.

Inch h b L1
CGWSR/L12 0.75 0.75 6.00
CGWSR/L16 1.00 1.00 6.00

Metric h b L1
CGWSR/L2020 20 20 137
CGWSR/L2525 25 25 137
Note: Right hand tool holders (R) use right hand cartridges (R)
Left hand tool holders (L) use left hand cartridges (L)

SPARE PARTS
Designation Blade screw
CGWSR/L... CSHB-6

CGWSRL
S h a n k o f to o l h o l d e r s . Ve r t i c a l t y p e w i t h o f f s e t b

L1
h

2-M6

Inch h b L1
CGWSRL12 0.75 0.75 6.00
CGWSRL16 1.00 1.00 6.00
Note: Right (R) or Left (L) hand cartridges can be used in this toolholder

SPARE PARTS
Designation Blade screw
CGWSRL... CSHB-6

C110 www.tungaloyamerica.com
CG W TR /L

Grooving Tool
Sha n k o f p e r p e nd i cul ar to o l ho l d er s C G W T R / L- G , - C G D, - F L & - #S / D

2-M6

b
f1
45°
L1

h
Right hand (R) shown.

Inch h b L1 f1
CGWTR/L12 0.75 0.75 6.00 1.50
CGWTR/L16 1.00 1.00 6.00 1.50

Metric h b L1 f1
CGWTR/L2020 20 20 150 37
CGWTR/L2525 25 25 150 37
Note: Right hand tool holders (R) use left hand cartridges (L)
Left hand tool holders (L) use right hand cartridges (R)

SPARE PARTS
Designation Blade screw
CGWTR/L... CSHB-6

CGTR /L
Too l h o l d e r s f o r i n ter nal g ro o v i ng

øDm

øDs
f

w h
ar

L1

Internal
Right hand (R) shown.

Inch W øDm ar øDs f L1 h Insert

A12Q-CGTR30U 0.118 1.0 0.138 0.75 0.571 7.09 0.709 G*30, GE30-AL
A16R-CGTR/L30U 0.118 1.26 0.197 1.00 0.728 7.87 0.961 G*30, GE30-AL
A16R-CGTR/L40U 0.157 1.26 0.197 1.00 0.728 7.87 0.961 G*40, GE40-AL
A20S-CGTR50U 0.197 1.575 0.236 1.25 0.906 9.84 1.21 G*50

SPARE PARTS Others

Designation Clamping screw Wrench
A***-CGTR/L... BHM5-14 P-3

Reference pages
Inserts → C112 - C115, Standard cutting conditions → C115

Tungaloy C111
Grooving Tool
- Chipbreaker Guide
1 corner inserts
External grooving and parting off
GE 1st choice for external 0.012
grooving and parting
0.010

Feed: f (ipr)
0.008
Excellent chip control for
grooving 0.006
External
0.004 Internal
W = 0.078" - 0.196"
0.002 Face
Parting off
0.078 0.118 0.157 0.196
Groove width : W (in)
Page C114

Parting off
GE R/L Handed insert 0.012

Feed: f (ipr)
0.010
Minimize burr generation when 0.008
workpiece is cut off
0.006

W = 0.118" - 0.196" 0.004

0.002

0.118 0.157 0.196

Groove width : W (in)
Page C114

Grooving and traversing

GT 1st choice for traversing
GT50
0.008
Depth of cut

Low cutting force and good GT40

ap (in)

chip control for traversing 0.004 GT30

W = 0.118" - 0.196"

0.002 0.004 0.006 0.008 0.010 0.012

Feed: f (ipr)
Page C114

Profiling
GR Full radius type
0.008 GR50
Depth of cut

Low cutting force and GR40

ap (in)

good chip control for profiling 0.004 GR30

W = 0.118" - 0.196"

0.002 0.004 0.006 0.008 0.010 0.012

Feed: f (ipr)

Page C114

C112 www.tungaloyamerica.com
 Grooving Tool
1 corner inserts
Face grooving
GF 1st choice for face grooving 0.012
0.010

Feed: f (ipr)
Low cutting force and good 0.008
chip control for face grooving 0.006
W = 0.118" - 0.196" 0.004
0.002

0.118 0.157 0.196

Groove width : W (in)

Page C114

Internal grooving
GN 1st choice for internal grooving 0.012
0.010

Feed: f (ipr)
Low cutting force and good chip 0.008
control for internal grooving 0.006
W = 0.118" - 0.196" 0.004
0.002

0.118 0.157 0.196

Groove width : W (in)

Page C114

For non-ferrous materials

GE-AL Reduce cutting force and 0.012
welding due to sharp 0.010
Feed: f (ipr)

chipbreaker 0.008
W = 0.078" - 0.157" 0.006
0.004
0.002

0.078 0.118 0.157

Groove width : W (in)

Page C114

Tungaloy C113
 INSERT
Grooving Tool GE GN
For general For internal

w
grooving grooving
rε L rε L

h
h
+0.1 +0.004
rε Coated Cermet L h W +0.1 W +0.004 rε Coated L h
Designation W 0 W 0 Designation 0 0

(mm) (in) (in) T9125 GH730 NS9530 (in) (in) (mm) (in) (in) GH730 (in) (in)
GE20 2 0.078 0.008 䖃 䖃 0.393 0.137 GN30 3 0.118 0.008 䖃 0.393 0.137

GE30 3 0.118 0.008 䖃 䖃 䖃 0.393 0.137 GN40 4 0.157 0.008 䖃 0.393 0.157

GE40 4 0.157 0.008 䖃 䖃 䖃 0.393 0.157 GN50 5 0.196 0.008 䖃 0.472 0.177

GE50 5 0.196 0.008 䖃 䖃 䖃 0.472 0.177

GT GR
For traversing For profiling
w

w
rε L rε L

h
h

+0.1 +0.004
rε Coated Cermet
L h +0.1 +0.004
rε Coated Cermet
L h
Designation W 0 W 0 Designation W 0 W 0
(mm) (in) (in) T9125 GH730 NS9530 (in) (in) (mm) (in) (in) T9125 GH730 NS9530 (in) (in)
GT30 3 0.118 0.016 䖃 䖃 0.393 0.137 GR30 3 0.118 0.059 䖃 䖃 0.393 0.137

GT40 4 0.157 0.016 䖃 䖃 0.393 0.157 GR40 4 0.157 0.078 䖃 䖃 䖃 0.393 0.157

GT50 5 0.196 0.016 䖃 䖃 䖃 0.472 0.177 GR50 5 0.196 0.098 䖃 䖃 䖃 0.472 0.177

G E-AL GF
For aluminum For face grooving
w
w

and non-ferrous (Improved chip

metals control) L
rε L rε
h
h

rε Uncoated L h +0.1 +0.004

rε Coated Cermet L h
Designation W W±0.001 Designation W 0 W 0
±0.025

(mm) (in) (in) KS05F (in) (in) (mm) (in) (in) GH730 NS9530 (in) (in)
GE20-AL 2 0.078 0.008 䖃 0.393 0.137 GF30 3 0.118 0.008 䖃 䖃 0.393 0.137

GE30-AL 3 0.118 0.008 䖃 0.393 0.138 GF40 4 0.157 0.008 䖃 䖃 0.393 0.157

GE40-AL 4 0.157 0.008 䖃 0.393 0.157 GF50 5 0.196 0.008 䖃 䖃 0.472 0.177

G E-R /L
For parting off rε L
(handed insert)
w

8˚
h

Right hand (R) shown.

W +0.1
0 W +0.004
0 rε Coated L h
Designation
(mm) (in) (in) GH730 (in) (in)
GE30R/L 3 0.118 0.008 䖃 0.393 0.137

GE40R/L 4 0.157 0.008 䖃 0.393 0.157

GE50R/L 5 0.196 0.008 䖃 0.472 0.177

䖃 : Line up

C114 www.tungaloyamerica.com
 STA N DA R D CUT T ING CONDIT IONS
Recommended Cutting speed

Grooving Tool
Workpiece material
grade vc (sfm)
T9125 260 - 650
Low carbon steels
Alloy steels ( ~ HB150)
NS9530 330 - 650
GH730 160 - 590
T9125 260 - 590
Medium carbon steels
NS9530 260 - 590
Alloy steels (HB150 ~ 250)
GH730 160 - 500
T9125 260 - 500
High carbon steels
Alloy steels (HB250 ~ )
NS9530 260 - 500
GH730 160 - 400
T9125 260 - 500
Stainless steels
GH730 160 - 400
T9125 260 - 650
Gray and ductile cast irons
GH730 160 - 590
Aluminum alloys, Non-ferrous metals KS05F 200 - 300

For External
Feed: f (ipr)
Operation Groove width: W (in)
0.078 0.118 0.157 0.196
Grooving
0.002 - 0.008 0.002 - 0.009 0.002 - 0.010 0.002 - 0.012
(GE**)
Parting off
0.001 - 0.003 0.001 - 0.006 0.001 ~ 0.006 0.001 - 0.006
(GE**R/L)
Depth of cut Depth of cut Depth of cut
Traversing
- ap = 0.008 - 0.060 ap = 0.020 - 0.078 ap = 0.020 - 0.098
(GT**)
f = 0.002 - 0.006 f = 0.002 - 0.009 f = 0.002 - 0.010
Depth of cut Depth of cut Depth of cut
Profiling
- ap = 0.050 - 0.055 ap = 0.008 - 0.060 ap = 0.020 - 0.062
(GR**)
f = 0.002 - 0.009 f = 0.002 - 0.010 f = 0.002 - 0.012
Grooving for Aluminum alloys
0.001 - 0.003 0.001 - 0.003 0.001 - 0.003 -
(GE**-AL)
• For diameter compensation values in traversing, see page C118.

For Face
Feed: f (ipr)
Operation Groove width: W (in)
0.118 0.157 0.196
Face grooving
0.002 - 0.009 0.002 - 0.009 0.003 - 0.016
(GE**)
Face grooving
0.002 - 0.010 0.002 - 0.010 0.002 - 0.012
(GF**)
Depth of cut Depth of cut Depth of cut
Face traversing
ap = 0.008 - 0.060 ap = 0.020 - 0.078 ap = 0.020 - 0.098
(GT**)
f = 0.002 - 0.006 f = 0.002 - 0.009 f = 0.002 - 0.010
Depth of cut Depth of cut Depth of cut
Face traversing
ap = 0.050 - 0.055 ap = 0.008 - 0.060 ap = 0.020 - 0.062
(GR**)
f = 0.002 - 0.009 f = 0.002 - 0.010 f = 0.002 - 0.012
Face grooving for aluminum alloys
0.001 - 0.003 0.001 - 0.003 -
(GE**-AL)
• For diameter compensation values in traversing, see page C118.
• For occurrence of vibrations in face traversing, set the feed to the lower side of the values show in the above table.

For Internal
Feed: f (ipr)
Operation Groove width: W (in)
0.118 0.157 0.196
Face grooving
0.002 - 0.006 0.002 - 0.006 0.002 - 0.006
(GE**)
Face grooving
0.002 - 0.006 0.002 - 0.007 0.002 -0.008
(GN**)
Face traversing ap = 0.008 - 0.060 ap = 0.020 - 0.078 ap = 0.020 - 0.098
(GT**) f = 0.002 - 0.006 f = 0.002 - 0.009 f = 0.002 - 0.010
Face traversing ap = 0.050 - 0.055 ap = 0.008 - 0.060 ap = 0.020 - 0.062
(GR**) f = 0.002 - 0.009 f = 0.002 - 0.010 f = 0.002 - 0.012
Face grooving for aluminum alloys
0.001 - 0.003 0.001 - 0.003 -
(GE**-AL)
• For diameter compensation values in traversing, see page C118.
• For occurrence of vibrations in face traversing, set the feed to the lower side of the values show in the above table.

Tungaloy C115
 Grooving Tool C G W S R /L-C G D
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g

ar
øDmax

b
f
w
L2 L1
Right hand (R) shown.

h1

h
The dashed line shows
20 mm-square shank tools.
L3
Metric W øDmax ar h b L1 L2 L3 h1 f Insert Shank Blade*
CGWSR/L2020-CGDR/L2 2 35 16 20 20 152 45 48.5 20 26.45 CGD200 CGWSR/L2020 CGDR/L2
CGWSR/L2525-CGDR/L2 2 35 16 25 25 152 45 - 25 31.45 CGD200 CGWSR/L2525 CGDR/L2
CGWSR/L2020-CGDR/L3 3 46 21.6 20 20 157.6 50.6 54.1 20 26.45 CGD300 CGWSR/L2020 CGDR/L3
CGWSR/L2525-CGDR/L3 3 46 21.6 25 25 157.6 50.6 - 25 31.45 CGD300 CGWSR/L2525 CGDR/L3
CGWSR/L2020-CGDR/L4 4 46 21.6 20 20 157.6 50.6 54.1 20 26.65 CGD400 CGWSR/L2020 CGDR/L4
CGWSR/L2525-CGDR/L4 4 46 21.6 25 25 157.6 50.6 - 25 31.65 CGD400 CGWSR/L2525 CGDR/L4
CGWSR/L2020-CGDR/L5 5 46 21.6 20 20 157.6 50.6 54.1 20 26.95 CGD500 CGWSR/L2020 CGDR/L5
CGWSR/L2525-CGDR/L5 5 46 21.6 25 25 157.6 50.6 - 25 31.95 CGD500 CGWSR/L2525 CGDR/L5
CGWSR/L2020-CGDR/L6 6 46 21.6 20 20 157.6 50.6 54.1 20 27.1 CGD600 CGWSR/L2020 CGDR/L6
CGWSR/L2525-CGDR/L6 6 46 21.6 25 25 157.6 50.6 - 25 32.1 CGD600 CGWSR/L2525 CGDR/L6
CGWSR2525-8 7/8 50 21.6 25 25 150 - - 25 26.35 CGD700, CGD800 - -
CGWSR3232-8 7/8 50 21.6 32 32 170 - - 32 33.35 CGD700, CGD800 - -
When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Blade Clamp Clamping Blade screw Spring pin Spring Wrench
screw
CGWSR****-CGDR2 TCR2 CCR2 RT-1 CSHB-6 - BP-9 P-4
CGWSL****-CGDL2 TCL2 CCL2 RT-1 CSHB-6 - BP-9 P-4
CGWSR****-CGDR3 TCR3 CCR3 RT-1 CSHB-6 - BP-9 P-4
CGWSL****-CGDL3 TCL3 CCL3 RT-1 CSHB-6 - BP-9 P-4

External CGWSR****-CGDR4 TCR4 CCR4 RT-1 CSHB-6 - BP-9 P-4

CGWSL****-CGDL4 TCL4 CCL4 RT-1 CSHB-6 - BP-9 P-4
CGWSR****-CGDR5 TCR5 CCR5 RT-1 CSHB-6 - BP-9 P-4
CGWSL****-CGDL5 TCL5 CCL5 RT-1 CSHB-6 - BP-9 P-4
CGWSR****-CGDR6 TCR6 CCR6 RT-1 CSHB-6 - BP-9 P-4
CGWSR****-CGDL6 TCL6 CCL6 RT-1 CSHB-6 - BP-9 P-4
CGWSR****-8 - CCR/L-8 CHHM6-20 - 5X14AW BP-9 P-5

Parting-off

Reference pages
Inserts, Standard cutting conditions → C117

C116 www.tungaloyamerica.com
 INSERT
CG D

Grooving Tool
w
rε

h L

W±0.025 W±0.001 rε Coated Cermet Uncoated L h

Designation
(mm) (in) (in) GH330 NS9530 UX30 (in) (in)
CGD200 2 0.078 0.008 䖃 䖃 䖃 0.787 0.128

CGD300 3 0.118 0.008 䖃 䖃 䖃 1.13 0.248

CGD400 4 0.157 0.008 䖃 䖃 䖃 1.13 0.248

CGD500 5 0.197 0.008 䖃 䖃 䖃 1.13 0.248

CGD600 6 0.236 0.008 䖃 䖃 䖃 1.13 0.335

CGD700 7 0.276 0.008 䖃 䖃 1.13 0.335

CGD800 8 0.315 0.008 䖃 䖃 1.13 0.335

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS

Cutting Groove width: W (in)

Operation speed Vc Feed: f (ipr)
(sfm) 0.078 0.118 0.157 0.197 0.236 0.276 0.315
Grooving Low 0.003 - 0.010 0.003 - 0.010 0.003 - 0.010 0.003 - 0.010 0.003 - 0.010
Carbon Steels
330 - 650 0.003 - 0.008 0.003 - 0.010
Grooving Medium 0.003 - 0.012 0.003 - 0.012 0.003 - 0.012 0.003 - 0.012 0.003 - 0.012
Carbon Steels

Parting off 100 - 150 0.003 - 0.006 0.003 - 0.006 0.003 - 0.006 0.003 - 0.006 0.003 - 0.006 0.003 - 0.006 0.003 - 0.006

Tungaloy C117
 Grooving Tool C G W S R /L-FLR/L#G P
E x te r n a l to o l h o l d er s f o r g ro o v i ng & t ur ni ng

5
2020 shank shown
Max. 14mm ar

25
2°

h1 h
f

2°
w
45 48.5
L1

5°
h1

h
Right hand (R) shown.

Metric W ar h b L1 h1 f Insert Shank Blade*

CGWSR/L2020-FLR/L3GP 3 10 20 20 152 20 27 FLEX30R/L CGWSR/L2020 FLR/L3GP
CGWSR/L2525-FLR/L3GP 3 10 25 25 152 25 32 FLEX30R/L CGWSR/L2525 FLR/L3GP
CGWSR/L2020-FLR/L4GP 4 12 20 20 152 20 27 FLEX40R/L CGWSR/L2020 FLR/L4GP
CGWSR/L2525-FLR/L4GP 4 12 25 25 152 25 32 FLEX40R/L CGWSR/L2525 FLR/L4GP
CGWSR/L2020-FLR/L5GP 5 14 20 20 152 20 27 FLEX50R/L CGWSR/L2020 FLR/L5GP
CGWSR/L2525-FLR/L5GP 5 14 25 25 152 25 32 FLEX50R/L CGWSR/L2525 FLR/L5GP
• When ordering, shank and blade assembly Designation or shank and blade-set are required.
• When using a right or left hand blade-set, the right hand blade-set is used with right hand shank and the left hand blade-set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWSR/L****-FLR/L*GP CHHM5-18 CSHB-6 P-4

Cautionary Notes
Feed direction Front cutting edge
When performing OD machining, the tool point must be set at a right angle to the axial
External
direction of the work.

• When replacing an insert, the replacement should be made only after completely
A'

removing any chips or other foreign matter from the tool clamping area on the
A

holder by using compressed air, etc.

• Never tighten the insert mounting screws when an insert has not been installed 0.03
outer diameter (mm)

since doing so can deform the screws and prevent the future installation of an
Correction value for

insert. 0.02

• Flex-Tool has mechanism in which the end cutting edge angle is formed by 0.01
accepting a cutting force. In external grooving, there is a possibility that if the cutting
Others conditions (feed and depth of cut) are set too high, the programmed diameter will 0
not be achieved. To prevent this problem, it is necessary to perform a compensation 0.1 0.2 0.3
in the program by an amount that is equal to the amount A'-A that is shown in the Feed: (mm/rev)
drawing on the right. The values of compensation corresponding to the feeds are Correction value for outer diameter (Reference)
also shown in the graph.

The length of blade for 5 mm width is shortened 2 mm compared from the old type
blade. Please notice and read the instruction manual packaged in the box.

Reference pages
Inserts → C119

C118 www.tungaloyamerica.com
CG W S R /L-FLR/L5T P

Grooving Tool
Too l h o l d e r s f o r f ace g ro o v i ng & t ur ni ng

shank shown

5°
2020
ar

h
25
b
Max. 6 mm

f
ø150≤

h1
øDm

w
45 48.5
L1

5°
h1

h
For face grooving
Right hand (R) shown.

Metric W øDm ar h b L1 h1 f Insert Shank Blade*

CGWSR/L2020-FLR/L5TP 5 150 6 20 20 152 20 27 FLEX50R/L CGWSR/L2020 FLR/L5TP
CGWSR/L2525-FLR/L5TP 5 150 6 25 25 152 25 32 FLEX50R/L CGWSR/L2525 FLR/L5TP
• When ordering, shank and blade assembly Designation or shank and blade set are required.
• When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.
* Blade sold separately.

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWSR/L****-FLR/L5TP CHHM5-18 CSHB-6 P-4

CG W TR /L0040- F LL/R3NP
Too l h o l d e r s f o r i n ter nal g ro o v i ng & t ur ni ng

øDs

b
60
40

øDm
ar
Max. 10 mm h
5°
w
30 L1 Right hand (R) shown.

Metric W øDm ar øDs L1 h b Insert Shank Blade*

CGWTR/L0040-FLL/R3NP 3 80 10 40 180 37.5 37 FLEX30L/R CGWTR/L0040 FLL/R3NP Internal

• When ordering, shank and blade assembly Designation or shank and blade set are required.
• When using a right or left hand blade set, the right hand blade set is used with left hand shank and the left hand blade set is used with right hand shank.
* Blade sold separately.
Face
Grooving

SPARE PARTS
Designation Clamping screw Blade screw Wrench
CGWTR/L0040-FLL/R3NP CHHM5-18 CSHB-6 P-4

A PPLICA B LE IN S ER T Others

F L E X ( R /L)
2°
4°

Recess
w

rε 2° 20
W1 A
7.1

Left hand inserts are identified

A with a recessed dot.
Right hand (R) shown.

wⴞ0.05 rε Coated Cermet Uncoated W1

Designation
(mm) (mm) T9125 NS9530 UX30 (mm)
FLEX30R/L 3 0.4 䖃 2.15

FLEX40R/L 4 0.4 䖃 3.1

FLEX50R/L 5 0.4 䖃 䖃 䖃 4

䖃 : Line up

Tungaloy C119
 Grooving Tool CTW R /L
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g , w i t h d o u b l e - e n d e d i n s e r t s

L1
L2
ar

b
f
Max. parting dia.
øDmax for solid bar

h1

h
Right hand (R) shown.

Metric W øDmax ar h b L1 L2 h1 f Insert

CTWR/L2020-3 3 32 14 20 20 150 41 20 20.25 CTD3
CTWR/L2525-3 3 32 14 25 25 150 41 25 25.25 CTD3
CTWR/L2020-4 4 32 14 20 20 150 41 20 20.25 CTD4
CTWR/L2525-4 4 32 14 25 25 150 41 25 25.25 CTD4
CTWR/L2525-5 5 42 20 25 25 150 46 25 25.25 CTD5

SPARE PARTS
Designation Clamp Pin Clamping Washer Wrench
screw
CTWR2020-3 CTC-3R BP-360 CTS-M6 CDW6 P-4
CTWL2020-3 CTC-3L BP-360 CTS-M6 CDW6 P-4
CTWR2525-3 CTC-3R BP-360 CTS-M6 CDW6 P-4
CTWL2525-3 CTC-3L BP-360 CTS-M6 CDW6 P-4
CTWR2020-4 CTC-4R BP-360 CTS-M6 CDW6 P-4
CTWL2020-4 CTC-4L BP-360 CTS-M6 CDW6 P-4
CTWR2525-4 CTC-4R BP-360 CTS-M6 CDW6 P-4
CTWL2525-4 CTC-4L BP-360 CTS-M6 CDW6 P-4
CTWR2525-5 CTC-5R BP-360 CTS-M6 CDW6 P-4
CTWL2525-5 CTC-5L BP-360 CTS-M6 CDW6 P-4

A PPLICA B LE IN S ER T
External
CT D
rε L
w
h1
h2

W±0.1 rε L h1 h2
Designation
(mm) (mm) AH725 (mm) (mm) (mm)
CTD3 3 0.2 䖃 20 4.3 4
Parting-off
CTD4 4 0.2 䖃 20 5.3 5

CTD5 5 0.2 䖃 25 6.3 6

䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S

Operation Cutting speed Feed: f (ipr)
(Work materials) vc (sfm) CTD3 CTD4 CTD5

Low carbon steels 0.003 - 0.009 0.003 - 0.009 0.003 - 0.009

Grooving 330 - 500
Medium carbon
0.003 - 0.012 0.003 - 0.012 0.003 - 0.012
steels

Parting off 330 - 500 0.003 - 0.006

C120 www.tungaloyamerica.com
CT H

Grooving Tool
B l a d e s f o r ex te r n a l g ro o v i n g & p a r t i n g

Max. parting dia.

b
øDmax for solid bar
6°

B1
h1
150

Metric W øDmax b h1 B1 Insert

CTH32-3 3 100 2.2 30.27 32.24 CT*3...
CTH32-4 4 100 3.2 30.13 31.97 CT*4...
CTH32-5 5 100 4.2 30 31.7 CT*5...
CTH32-6 6 100 5.2 29.87 31.44 CT*6...

SPARE PARTS
Designation Wrench
CTH... CTL-2

External

Parting-off

Reference pages
Inserts, Standard cutting conditions → C124

Tungaloy C121
Grooving Tool CTB N /S-32
To o l b l o c k f o r CT H b l ad es

CTBN CTBS

5°
h1

h1
51
h0 h
51

h
h0
18
R 100 23 19 110
110 6 R

Metric h h1 h0 ℓ Blade*
CTBN20-32 20 20.2 19.6 38 CTH32...
CTBN25-32 25 25.2 14.6 38 CTH32...
CTBN32-32 32 32.2 7.6 43 CTH32...
CTBS20-32 20 20.2 19.4 48 CTH32...
CTBS25-32 25 25.2 14.4 48 CTH32...
CTBS32-32 32 32.2 7.4 48 CTH32...
* Blade sold separately.

SPARE PARTS
Designation Wedge clamping screw Wedge Wrench
CTBN**-32 NDS-8S CTW-2 P-4
CTBS**-32 DS-8 CTW-2 P-4

C122 www.tungaloyamerica.com
CTSR /L

Grooving Tool
B l a d e s f o r ex te r n a l g ro o v i n g & p a r t i n g

øDmax

b
18.0

25
25
Right hand (R) shown.

Metric W øDmax b Insert

CTSR/L25-3 3 50 2.2 CT*3...
CTSR/L25-4 4 50 3.2 CT*4...
CTSR25-5 5 50 4.2 CT*5...
CTSR25-6 6 50 5.2 CT*6...
• Refer to the assembly drawing of "CTBR/L" regarding the dimensions.

SPARE PARTS
Designation Wrench
CTSR/L... CTL-2

TO OLH OLD ER
CTB R /L b

(CTBR/L20-25 type shown)

f0
f
w

L1 45
45
25
h h1

h
h1

6°
47 Right hand (R) shown.

W Metric Blade ar h1 h b L1 f0 f
3,4 CTBR/L20-25 CTSR/L25-3/4 Max.25Max.cut off dia.ø50 20.2 20 25 150 19.6 22.6/23.6 External

3,4,5,6 CTBR/L25-25 CTSR/L25-3/4/5/6 Max.25Max.cut off dia.ø50 25.2 25 25 150 24.6 27.6/28.6/29.6/30.6
When using a right or left hand blade set, the right hand blade set is used with right hand shank and the left hand blade set is used with left hand shank.

SPARE PARTS
Designation Clamping Screw Wrench
CTBR/L... M6×20 P-5

Parting-off

Reference pages
Inserts, Standard cutting conditions → C124

Tungaloy C123
 INSERT for CTH, CTS T Y PE PA RTING OFF TO OLHOLD ER
Grooving Tool CTN /CTR /CT L
rε

3°
CTN CTR CTL

w
rε
8°

5° 8°
rε
0.394 Neutral (N) shown Right hand (R) Left hand (L)

Coated Uncoated
W±0.2 W±0.008 rε
Designation T313W TH10
(mm) (in) (in)
N R L N R L
CTN3 3 0.118 0.008 䖃
CTR/L3 3 0.118 0.008 䖃 䖃
CTN3K 3 0.118 0.008 䖃
CTR/L3K 3 0.118 0.008 䖃 䖃
CTN4 4 0.157 0.008 䖃
CTR/L4 4 0.157 0.008 䖃 䖃
CTN4K 4 0.157 0.008 䖃
CTR/L4K 4 0.157 0.008 䖃 䖃
CTN5 5 0.197 0.012 䖃
CTR/L5 5 0.197 0.012 䖃
CTN5K 5 0.197 0.012 䖃
CTR/L5K 5 0.197 0.012 䖃
CTN6 6 0.236 0.012 䖃
CTN6K 6 0.236 0.012 䖃

䖃 : Line up

STAN DARD CUT T ING CONDIT IO N S F O R CT H , CTS

Operation / Cutting speed Feed: f (ipr)
Workpiece material vc (sfm) CTN3 CTN4 CTN5 CTN6 CTR/L䊐 CT䊐䊐K
Low carbon steels 0.003 - 0.009 0.003 - 0.009
330 - 500 0.003 - 0.009 0.003 -0.012 -
Grooving Medium carbon steels 0.003 -0.012 0.003 -0.012 -
Cast irons, Light alloys 330 - 660 - - - - 0.004 - 0.006
Low carbon steels
330 - 500 0.003 - 0.008 0.003 - 0.008 0.003 - 0.008 0.003 - 0.008 0.003 - 0.006 -
Parting off Medium carbon steels
Cast irons, Light alloys 330 - 660 - - - - - 0.004 - 0.012
Note: When using CTS type (blade type) toolholders, reduce the values given in the table by 80 %.

C124 www.tungaloyamerica.com
 - Q uick Guide

Grooving Tool
The insert’s secure & unique clamping
guarantees reliable machining in grooving
and turning

1
External

5 Internal

Face
Grooving

1 EGP 2 ETFR/L 3 EFPR/L 4 ETIR/L 5 ETER/L Parting-off

Blade type W = 0.16" - 0.24" Blade type W = 0.16" - 0.24" W = 0.16" - 0.24"
W = 0.16" - 0.24" (4 - 6 mm) W = 0.16" - 0.24" (4 - 6 mm) (4 - 6 mm)
Others
(4 - 6 mm) ar = 0.591" - 1.260" (4 - 6 mm) ar = 0.24" - 0.433" ar = 0.984" - 1.378"
Max. parting Dia.: (15 - 32 mm) ar = Max.: 2.559" (6 - 11 mm) (25 - 35 mm)
4.724" (120 mm) Shank size: (65 mm) Shank size: Shank size:
Shank size: 0.750" - 1.000" Shank size: 1.000" 0.625" - 1.250" 0.750" - 1.250"
0.800" - 0.126" (20 - 25 mm) (25 mm) (16 - 32 mm) (20 - 32 mm )
(20 - 32 mm ) Page C130 Page C132 Page C129 Page C126
Page C127
ETFR-CHP
EGP-CHP W = 0.16" (4 mm)
Blade type Shank size:
W = 0.16" - 0.24" 0.800" - 0.126"
(4 - 6 mm) (20 - 32 mm )
Max. parting Dia.: Shank size: 1.000"
4.724" (120 mm) (25 mm)
Shank size: Page C131
0.800" - 0.126"
(20 - 32 mm )
Page C128

Tungaloy C125
 Grooving Tool ETE R /L
E x te r n a l to o l h o l d e r s f o r g ro o v i n g & p a r t i n g & t u r n i n g

ar

b
f
Rib L1

h1

h
Right hand (R) shown.

Inch W ar h1 b h L1 f Insert Rib

ETER/L12-4T25 0.157 0.984 0.750 0.750 0.750 5.000 0.766 E**4... Without
ETER/L16-4T25 0.157 0.984 1.000 1.000 1.000 6.000 1.016 E**4... Without
ETER/L20-4T30 0.157 1.181 1.250 1.250 1.250 7.000 1.266 E**4... Without
ETER/L12-5T25 0.197 0.984 0.750 0.750 0.750 5.000 0.766 ETX5... Without
ETER/L16-5T32 0.197 1.260 1.000 1.000 1.000 6.000 1.016 ETX5... Without
ETER/L20-5T32 0.197 1.260 1.250 1.250 1.250 7.000 1.266 ETX5... Without
ETER/L16-6T35 0.236 1.378* 1.000 1.000 1.000 6.000 1.016 ETX6... With
ETER/L20-6T35 0.236 1.378** 1.250 1.250 1.250 7.000 1.266 ETX6... With
* Max. ø6.69"
**Max. ø13.38"

SPARE PARTS
Designation Wrench (Optional parts)
ETER/L12-4T25 (ECW-456EF)
ETER/L16-4T25 (ECW-456EF)
ETER/L20-4T30 (ECW-456EF)
ETER/L12-5T25 (ECW-456EF)
ETER/L16-5T32 (ECW-456EF)
ETER/L20-5T32 (ECW-456EF)
ETER/L16-6T35 (ECW-456EF)
ETER/L20-6T35 (ECW-456EF)

External

Parting-off

Others

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

C126 www.tungaloyamerica.com
EG P

Grooving Tool
B l a d e s f o r ex te r n a l d e e p g ro o v i n g & p a r t i n g

w øDmax L1

B1
b

h1
150˚

Inch W øDmax h1 b B1 L1 Insert

EGP26-4D 0.157 3.150 0.843 0.126 1.024 5.906 E**4...
EGP32-4D 0.157 3.937 0.980 0.126 1.260 5.906 E**4...
EGP32-5D 0.197 4.724 0.980 0.157 1.260 5.906 ETX5...
EGP32-6D 0.236 4.724 0.980 0.205 1.260 5.906 ETX6...

• øDmax: Max. parting off diameter

SPARE PARTS
Designation Wrench (Optional parts)
EGP26-4D (ECW-456EF)
EGP32-*D (ECW-456EF)

CT B U
Too l b l o c k f o r CG P and E G P b l ad es
B1

h4
h1

External
h

L2 L1
h2

L3
Inch h1 B1 L1 h h2 h4 L2 L3 Blade*
CTBU12-26-U 0.843 1.024 3.386 0.750 0.354 1.693 0.827 1.496 EGP26...
CTBU16-26-U 0.843 1.024 4.331 1.000 0.197 1.772 0.906 1.654 EGP26...
CTBU12-32-U 0.976 1.260 3.937 0.750 0.512 1.969 0.748 1.496 EGP32...
CTBU16-32-U 0.976 1.260 4.331 1.000 0.315 1.969 0.906 1.654 EGP32...
Parting-off
CTBU20-32-U 0.976 1.260 4.331 1.250 0.197 2.126 1.142 1.890 EGP32...
* Blade sold separately.

SPARE PARTS
Designation Clamp Clamping screw Wrench
CTBU12-26-U CT-86 CM6x30-S P-5
CTBU16-26-U CT-100 CM6x30-S P-5
CTBU12-32-U CT-105 CM6x30-S P-5
CTBU16-32-U CT-110 CM6x30-S P-5
CTBU20-32-U CT-110 CM6x30-S P-5

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

Tungaloy C127
 EG P-C H P
Grooving Tool
Bl a d e s f o r ex ter nal d eep g ro o v i ng & p ar t i n g, w i t h c h a n n e l s f or h i gh p re s s u re c ool a n t .

w øDmax L1

h
b

h1
150˚

Metric W øDmax ar h b L1 h1 Insert

EGP32-4D-CHP 4 100 50 32 3.4 150 24.9 E**4...
EGP32-5D-CHP 5 120 60 32 4.2 160 24.9 ETX5...
EGP32-6D-CHP 6 120 60 32 5.2 160 24.9 ETX6...
• øDmax: Max. parting off diameter

SPARE PARTS
Designation Sealing screw Wrench (Optional parts)
EGP32-*D-CHP SGC340 (ECW-456EF)

CTB U -C H P
To o l b l o c k s f o r exter nal d eep p ar t i ng and groov i n g b l a d e s w i t h c h a n n e l s f or h i gh p re s s u re c ool a n t

L1
h4
B1

h1

L2 G1/8’’-28
h2

External
L3

Inch h B1 L2 L1 h1 h2 h4 L3 Blade*
CTBU16-32-U-CHP 1.000 1.260 0.906 4.331 0.976 0.315 1.969 1.654 EGP32-*D-CHP
* Blade sold separately.

SPARE PARTS
Designation Sealing screw Clamp Wrench O-ring
CTBU16-32-U-CHP SRM6X16DIN912-12.9 CT-110 P-5 OR14X2.5NN

Parting-off

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

C128 www.tungaloyamerica.com
ETI R /L

Grooving Tool
I n te r n a l to o l h o l d er s f o r g ro o v i ng & t ur ni ng

L2

øDs
f

ar
øDm w L1

h
Right hand (R) shown.

Inch W øDm ar øDs h L1 f L2 Insert

ETIR/L10-4T06-D12 0.157 0.750 0.236 0.625 0.600 6.500 0.590 1.575 E**4...
ETIR/L12-4T06-D16 0.157 1.000 0.236 0.750 0.725 6.500 0.651 1.575 E**4...
ETIR/L16-4T09-D20 0.157 1.250 0.354 1.000 0.975 7.500 0.884 1.575 E**4...
ETIR/L20-4T11-D24 0.157 1.500 0.433 1.250 1.188 10.000 1.088 2.362 E**4...
ETIR/L20-5T11-D24 0.197 1.500 0.433 1.250 1.188 10.000 1.088 2.362 ETX5...
ETIR/L20-6T11-D24 0.236 1.500 0.433 1.250 1.188 10.000 1.098 2.362 ETX6...
• Wrench should be ordered separately.

SPARE PARTS
Designation Seal cap Wrench
(Optional parts: internal screw) (Optional parts)
ETIR/L10-4T06-D12 CA-16(M6) (ECW-456l)
ETIR/L12-4T06-D16 CA-20(M6) (ECW-456l)
ETIR/L16-4T09-D20 CA-25(R1/8") (ECW-456EF)
ETIR/L20-4T11-D24 CA-32(R1/8") (ECW-456EF)
ETIR/L20-5T11-D24 CA-32(R1/8") (ECW-456EF)
ETIR/L20-6T11-D24 CA-32(R1/8") (ECW-456EF)

Internal

Others

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

Tungaloy C129
 Grooving Tool ETFR /L
To o l h o l d e r s f o r f ace g ro o v i ng & t ur ni ng

w
ar

b
f
øDm
L1 øDmax

h1

h
Right hand (R) shown.

Inch W øDm øDmax ar h b L1 h1 f Insert

ETFR/L12-4T15-030035 0.157 1.181 1.378 0.591 0.750 0.750 0.750 5.000 0.770 E**4...
ETFR/L16-4T15-030035 0.157 1.181 1.378 0.591 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L12-4T22-035045 0.157 1.378 1.772 0.866 0.750 0.750 0.750 5.000 0.770 E**4...
ETFR/L16-4T22-035045 0.157 1.378 1.772 0.866 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L12-4T25-045055 0.157 1.772 2.165 0.984 0.750 0.750 0.750 5.000 0.770 E**4...
ETFR/L16-4T25-045055 0.157 1.772 2.165 0.984 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L12-4T25-055075 0.157 2.165 2.953 0.984 0.750 0.750 0.750 5.000 0.770 E**4...
ETFR/L16-4T25-055075 0.157 2.165 2.953 0.984 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L12-4T25-075120 0.157 2.953 4.724 0.984 0.750 0.750 0.750 5.000 0.770 E**4...
ETFR/L16-4T25-075120 0.157 2.953 4.724 0.984 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L16-4T25-120200 0.157 4.724 7.874 0.984 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L16-4T25-200500 0.157 7.874 19.685 0.984 1.000 1.000 1.000 6.000 1.020 E**4...
ETFR/L16-5T25-035045 0.197 1.378 1.772 0.984 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-5T25-045055 0.197 1.772 2.165 0.984 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-5T25-055075 0.197 2.165 2.953 0.984 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-5T32-075120 0.197 2.953 4.724 1.260 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-5T32-120200 0.197 4.724 7.874 1.260 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-5T32-200500 0.197 7.874 19.685 1.260 1.000 1.000 1.000 6.000 1.020 ETX5...
ETFR/L16-6T25-040055 0.236 1.575 2.165 0.984 1.000 1.000 1.000 6.000 1.020 ETX6...
ETFR/L16-6T25-055075 0.236 2.165 2.953 0.984 1.000 1.000 1.000 6.000 1.020 ETX6...
ETFR/L16-6T32-075120 0.236 2.953 4.724 1.260 1.000 1.000 1.000 6.000 1.020 ETX6...
ETFR/L16-6T32-120200 0.236 4.724 7.874 1.260 1.000 1.000 1.000 6.000 1.020 ETX6...
ETFR/L16-6T32-200500 0.236 7.874 19.685 1.260 1.000 1.000 1.000 6.000 1.020 ETX6...

SPARE PARTS
Designation Wrench (Optional parts)
ETFR/L... (ECW-456EF)

Face
Grooving

Others

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

C130 www.tungaloyamerica.com
ETFR -C H P

Grooving Tool
Too l h o l d e r s f o r face g ro o v i ng & t ur ni ng , w i t h c h a n n e l s f or h i gh p re s s u re c ool a n t .

w
ar

b
f
øDm
L1 øDmax

h1

h
Right hand (R) shown.

Inch W øDm øDmax ar h b L1 h1 f Insert

ETFR16-4T15-030035-CHP 0.157 1.181 1.378 0.591 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T22-035045-CHP 0.157 1.378 1.772 0.866 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T25-045055-CHP 0.157 1.772 2.165 0.984 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T25-055075-CHP 0.157 2.165 2.953 0.984 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T25-075120-CHP 0.157 2.953 4.724 0.984 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T25-120200-CHP 0.157 4.724 7.874 0.984 1.000 1.000 6.000 1.000 1.020 E**4...
ETFR16-4T25-200500-CHP 0.157 7.874 19.685 0.984 1.000 1.000 6.000 1.000 1.020 E**4...

SPARE PARTS
Designation Wrench (Optional parts)
ETFR****-CHP (ECW-456EF)

Face
Grooving

Others

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

Tungaloy C131
 Grooving Tool EFPR /L
Fa c e g ro o v i n g b l ad e

f
øDm
øDmax
W

ar
L1
Right hand (R) shown

Inch W øDm øDmax f L1 min ar max ar Insert

EFPR/L-4-030035 0.157 1.181 1.378 0.535 4.921 0.709 1.968 E**4...
EFPR-4-035045 0.157 1.378 1.772 0.535 4.921 0.709 1.968 E**4...
EFPR-4-045055 0.157 1.772 2.165 0.535 4.921 0.709 1.968 E**4...
EFPR-4-055075 0.157 2.165 2.953 0.535 4.921 0.709 1.968 E**4...
EFPR-4-075120 0.157 2.953 4.724 0.535 5.512 0.709 2.559 E**4...
EFPR-4-120200 0.157 4.724 7.874 0.535 5.512 0.709 2.559 E**4...
EFPR-4-200500 0.157 7.874 19.685 0.535 5.512 0.709 2.559 E**4...
EFPR-5-035045 0.197 1.378 1.772 0.535 4.921 0.748 1.968 ETX5...
EFPR-5-045055 0.197 1.772 2.165 0.535 4.921 0.748 1.968 ETX5...
EFPR-5-055075 0.197 2.165 2.953 0.535 4.921 0.748 1.968 ETX5...
EFPR-5-075120 0.197 2.953 4.724 0.535 5.512 0.748 2.559 ETX5...
EFPR-5-120200 0.197 4.724 7.874 0.535 5.512 0.748 2.559 ETX5...
EFPR-5-200500 0.197 7.874 19.685 0.535 5.512 0.748 2.559 ETX5...
EFPR-6-045055 0.236 1.772 2.165 0.535 4.921 0.787 1.968 ETX6...
EFPR-6-055075 0.236 2.165 2.953 0.535 4.921 0.787 1.968 ETX6...
EFPR-6-075120 0.236 2.953 4.724 0.535 5.512 0.787 2.559 ETX6...
EFPR-6-120200 0.236 4.724 7.874 0.535 5.512 0.787 2.559 ETX6...
EFPR/L-6-200500 0.236 7.874 19.685 0.535 5.512 0.787 2.559 ETX6...

SPARE PARTS
Designation Wrench (Optional parts)
EFPR/L... (ECW-456I)

Face
Grooving

Others

Reference pages
Inserts → C134 - C135, Standard cutting conditions → C135

C132 www.tungaloyamerica.com
CT B U -C H P f or EF P R/L

Grooving Tool
Too l b l o c k f o r E F P b l ad es, w i t h channel s f o r h i gh p re s s u re c ool a n t .

h
h2
L2 b L1

Inch W øDm h b h2 L2 L1 Blade*

CTBU16-030-4U-CHP 0.157 1.181 1.000 0.905 0.315 1.024 4.331 EFPR/L-4-030035
CTBU16-035-4/5U-CHP 0.157, 0.197 1.378 1.000 0.905 0.315 1.024 4.331 EFPR/L-4/5-035045
CTBU16-045-4/5U-CHP 0.157, 0.197 1.772 1.000 0.905 0.315 1.024 4.331 EFPR/L-4/5-045055
CTBU16-055-4/5U-CHP 0.157, 0.197 2.165 1.000 0.905 0.315 0.945 4.331 EFPR/L-4/5-055075
CTBU16-075-4/5U-CHP 0.157, 0.197 2.953 1.000 0.905 0.315 0.866 4.331 EFPR/L-4/5-075120
CTBU16-120-4/5U-CHP 0.157, 0.197 4.724 1.000 0.905 0.315 0.827 4.331 EFPR/L-4/5-120200
CTBU16-200-4/5U-CHP 0.157, 0.197 7.874 1.000 0.905 0.315 0.728 4.331 EFPR/L-4/5-200500
CTBU16-045-6U-CHP 0.236 1.772 1.000 0.905 0.315 1.102 4.331 EFPR/L-6-045055
CTBU16-055-6U-CHP 0.236 2.165 1.000 0.905 0.315 1.024 4.331 EFPR/L-6-055075
CTBU16-075-6U-CHP 0.236 2.953 1.000 0.905 0.315 0.945 4.331 EFPR/L-6-075120
CTBU16-120-6U-CHP 0.236 4.724 1.000 0.905 0.315 0.906 4.331 EFPR/L-6-120200
CTBU16-200-6U-CHP 0.236 7.874 1.000 0.905 0.315 0.807 4.331 EFPR/L-6-200500
* Blade sold separately.

SPARE PARTS
Designation Clamp Clamping screw Wrench
CTBU...-CHP CT-110 CM6X30-S P-5

Face
Grooving

Others

Tungaloy C133
Grooving Tool - Chipbreaker Guide

Multi-functional insert Standard feed for Standard feed and depth

ETX type grooving of cut for turning
Well-balanced sharpness
and strength 0.016
0.16

Feed: f (ipr)

Depth of cut
0.012
W = 0.157" - 0.236" 0.12

ap (in)
0.008
0.08
0.004 0.04

0 0
0.157 0.197 0.236 0.004 0.008 0.012 0.016
Page C135 Groove width: W (in) Feed: f (ipr)

Standard feed for grooving

EGM type First choice for parting off
0.016
Well-designed edge with

Feed: f (ipr)
high strength 0.012

W = 0.157" 0.008

0.004

0
0.157
Groove width: W (in)
Page C135

C134 www.tungaloyamerica.com
 INSERT
ETX EGM

Grooving Tool
L
L
W rε W rε

W±0.05 W±0.002 rε L W±0.05 W±0.002 rε L

Designation AH725 Designation AH725
(mm) (in) (in) (in) (mm) (in) (in) (in)
ETX4-040 4 0.157 0.016 䖃 0.315 EGM4-030 4 0.157 0.012 䖃 0.315

ETX5-040 5 0.197 0.016 䖃 0.394 䖃 : Line up

ETX6-040 6 0.236 0.016 䖃 0.472

䖃 : Line up

STA N DA R D CUT T ING CONDIT IONS

Chip- Cutting speed
ISO Workpiece material Hardness Grades
breaker Vc (sfm)

Low carbon steel - 300 HB AH725 ETX 160 - 600

(1018, 1020, 1026, etc.) - 300 HB AH725 EGM 160 - 600

Carbon steel, Alloy steel - 300 HB AH725 ETX 160 - 600

(1045, 1055, etc.) - 300 HB AH725 EGM 160 - 600

Prehardened steel - 300 HB AH725 ETX 160 - 600

(NAK80, PX5, etc.) - 300 HB AH725 EGM 160 - 600

Stainless steel - AH725 ETX 160 - 400

(304SS, 316SS, 17-4 PH, etc.) - AH725 EGM 160 - 400

Tungaloy C135
 PR OC EDURE TO CLA M P A ND U N C L AM P I N S E R T

1 Put the insert in the 2 Turn the wrench and 3 Unclamp

Grooving Tool
pocket push the insert into the
pocket to clamp

B
A

A Twist the wrench

B Push out the insert from
the pocket to unclamp

PARTS FOR COOLANT HOSE

Connecting hose
Fig. 1 Th Th1 Fig. 2 Th1
L Th
L

Length Threading size Max. pressure

Metric Fig.
L Th Th1 (MPa)
CHP-HOSE-G1/8-7/16-200BS 200 G1/8"-28 BSPP 7/16"-20 UNF 26 1

CHP-HOSE-G1/8-7/16-250BS 250 G1/8"-28 BSPP 7/16"-20 UNF 26 1

CHP-HOSE-5/16-7/16-200BS 200 5/16"-24UNF 7/16"-20 UNF 20 1

CHP-HOSE-5/16-G1/8-200BS 200 5/16"-24UNF G1/8"-28 BSPP 20 1

CHP-HOSE-G1/8-G1/8-200BB 200 G1/8"-28 BSPP G1/8"-28 BSPP 26 2

CHP-HOSE-G1/8-G1/8-250BB 250 G1/8"-28 BSPP G1/8"-28 BSPP 26 2

Connector Seal washer

HEX9/16”
7/16”-20 UNF 1/8”-28 BSPP
4.0

ød
øD
13.8

37°

14 7.1 W
28.75

Metric Metric øD ød W
CHP-NIPPLE-G1/8-7/16UNF CHP-COPPER-SEAL1/8 15 10 1

CHP-COPPER-SEAL5/16 11 8 1

Connector for small lathe CHP-COPPER-SEAL5/16-2.5 11 8 2.5

with seal washer

SW = 12
9
G1/8”-28 BSPP

6
11
4

25 ø13
5/16”-24 UNF

Metric
CHP-CONECTOR/5/16-G1/8

C136 www.tungaloyamerica.com
 - Q uick Guide

Grooving Tool
Efficiently reduces machining time of
wide width grooving and forming!
Effectively reduces the number of passes or machining time of
complex profiles!

External

2
3

Others

1 FPGN 2 FPGR 3 SPGN

Lever lock type Lever lock type Screw clamp type
W = 0.394" - 0.984" W = 0.394" - 0.984" W = 0.394" - 0.984"
(10 - 25 mm) (10 - 25 mm) (10 - 25 mm)
ar = 0.787" - 1.614" ar = 0.787" - 2.615" ar = 0.984" - 1.614"
(20 - 36 mm) (20 - 50 mm) (20 - 36 mm)
Shank size: Shank size: Shank size:
0.500" - 1.000" 1.000" - 1.500" 0.500" - 1.000"
(12 - 25 mm) (25 - 40 mm) (12 - 25 mm)
Page C139 Page C138 Page C139

Tungaloy C137
 Grooving Tool FPG R
Le v e r l o c k t y pe f o r exter nal w i d e g ro o v i ng a n d p rof i l i n g

ar

b
W
f
L1

h1

h
h2
t
Inch W ar PSGB ar PSGM h1 b h L1 PSGB L1 PSGM f h2 t PSGB t PSGM Insert(1)
FPGR16-10T20 0.394 0.984 0.787 1.000 1.000 1.000 7.196 7.000 1.020 - 0.216 0.019 PSG*10...
FPGR20-10T36 0.394 1.614 1.417 1.250 1.250 1.250 8.196 8.000 1.270 - 0.216 0.019 PSG*10...
FPGR16-15T20 0.590 0.984 0.787 1.000 1.000 1.000 7.196 7.000 1.020 - 0.216 0.019 PSG*15...
FPGR20-15T40 0.590 1.771 1.574 1.250 1.250 1.250 8.196 8.000 1.270 - 0.216 0.015 PSG*15...
FPGR20-20T40 0.787 1.771 1.574 1.250 1.250 1.250 8.196 8.000 1.270 0.314 0.216 0.015 PSG*20...
FPGR24-20T50 0.787 2.165 1.968 1.500 1.500 1.500 10.917 10.000 1.520 0.314 0.216 0.015 PSG*20...
FPGR20-25T40 0.984 1.771 1.574 1.250 1.250 1.250 8.196 8.000 1.270 0.314 0.216 0.015 PSG*25...
FPGR24-25T50 0.984 2.615 1.968 1.500 1.500 1.500 10.917 10.000 1.520 0.314 0.216 0.015 PSG*25...
(1) Can be used with both wide grooving and profile grooving inserts

SPARE PARTS
Designation Lever Clamping Spring Wrench
screw
FPGR*****-10T..., 15T... FCL4 FCS3 BP-5 P-2.5
FPGR*****-20T..., 25T... FCL8 FCS6 BP-9 P-5

External

Others

Reference pages
Inserts → C140 - C141, Standard cutting conditions → C141

C138 www.tungaloyamerica.com
FPGN

Grooving Tool
Le v e r l o c k t y p e fo r exter nal w i d e g ro o v i ng an d p rof i l i n g

ar

b
f
L1

h1

h
t
Inch W ar PSGB ar PSGM h1 b h L1 PSGB L1 PSGM f t PSGB t PSGM Insert(1)
FPGN08-10T20 0.394 0.984 0.787 0.500 0.500 0.500 4.946 4.750 0.450 0.216 0.019 PSG*10...
FPGN10-10T20 0.394 0.984 0.787 0.625 0.625 0.625 4.946 4.750 0.510 0.216 0.019 PSG*10...
FPGN12-10T20 0.394 0.984 0.787 0.750 0.750 0.750 5.196 5.000 0.570 0.216 0.019 PSG*10...
FPGN10-15T25 0.590 1.181 0.984 0.625 0.625 0.625 4.946 4.750 0.610 0.216 0.015 PSG*15...
FPGN12-15T25 0.590 1.181 0.984 0.750 0.750 0.750 5.196 5.000 0.670 0.216 0.015 PSG*15...
FPGN12-20T32 0.787 1.456 1.259 0.750 0.750 0.750 5.196 5.000 0.770 0.216 0.015 PSG*20...
FPGN16-20T32 0.787 1.456 1.259 1.000 1.000 1.000 6.196 6.000 0.890 0.216 0.015 PSG*20...
FPGN16-25T36 0.984 1.614 1.417 1.000 1.000 1.000 6.196 6.000 0.990 0.216 0.015 PSG*25...
• We can make special shape with forming insert (PSGB type) responding to customer's request.(1) Can be used with both wide grooving and profile grooving inserts

SPARE PARTS
Designation Lever Clamping Spring Wrench
screw
FPGN*****-10T..., 15T... FCL4 FCS3 BP-5 P-2.5
FPGN*****-20T..., 25T... FCL8 FCS6 BP-9 P-5

SP G N
Scre w -o n t y p e , f o r exter nal w i d e g ro o v i ng an d p rof i l i n g

ar
W

b
f

External
L1
h1

t
Inch W ar h1 b h L1 f t Insert(1)
SPGN08-10T20 0.394 0.984 0.500 0.500 0.500 4.946 0.450 0.216 PSGB10
SPGN10-10T20 0.394 0.984 0.625 0.625 0.625 4.946 0.510 0.216 PSGB10
SPGN12-10T20 0.394 0.984 0.750 0.750 0.750 5.196 0.570 0.216 PSGB10
SPGN10-15T25 0.590 1.181 0.625 0.625 0.625 4.946 0.610 0.216 PSGB15
SPGN12-15T25 0.590 1.181 0.750 0.750 0.750 5.196 0.670 0.216 PSGB15
SPGN12-20T32 0.787 1.456 0.750 0.750 0.750 5.196 0.770 0.216 PSGB20 Others
SPGN16-20T32 0.787 1.456 1.000 1.000 1.000 6.196 0.890 0.216 PSGB20
SPGN16-25T36 0.984 1.614 1.000 1.000 1.000 6.196 0.990 0.216 PSGB25
• We can make special shape with forming insert (PSGB type) responding to customer's request.(1) Can be used with profile grooving inserts, only

SPARE PARTS
Designation Clamping screw Wrench
SPGN*****-10T20 CSTB-3L081 T-8F
SPGN*****-15T25 CSTB-4 T-15F
SPGN*****-20T..., 25T... CSTB-5 T-20F

Reference pages
Inserts → C140 - C141, Standard cutting conditions → C141

Tungaloy C139
Grooving Tool - Chipbreaker Guide

PSGM For wide grooving 0.020

Excellent chip control

Feed: f (ipr)
0.016
W = 0.394" - 0.984" 0.012
(10 mm - 25 mm)
0.008

0.004

0.394 0.591 0.787 0.984

Groove width : W (in)
Page C141

PSGB Blank for profiling shape Specially tailored profile inserts

W = 0.402" - 0.992"
(10.2 mm - 25.2 mm)

Page C141

C140 www.tungaloyamerica.com
 INSERT
For wide grooving Blanks for wide profile grooving*

Grooving Tool
L

L
W* s

rε
W s
W* W* rε Coated L s W ±0.025 W ±0.001 Uncoated L s
Designation Designation
(mm) (in) (in) AH725 (in) (in) (mm) (in) UX30 TH10 (in) (in)
PSGM10-08 10 0.394 0.032 䖃 0.433 0.157 PSGB10 10.2 0.402 䖃 䖃 0.709 0.157

PSGM15-15 15 0.590 0.059 䖃 0.591 0.197 PSGB15 15.2 0.598 䖃 䖃 0.787 0.197

PSGM20-20 20 0.787 0.079 䖃 0.866 0.256 PSGB20 20.2 0.795 䖃 䖃 1.062 0.256

PSGM25-20 25 0.984 0.079 䖃 0.866 0.256 PSGB25 25.2 0.992 䖃 䖃 1.062 0.256

*: Tolerance W ± 0.003 (W = 0.394), ± 0.004 (W ≥ 0.591) 䖃 : Line up 䖃 : Line up

*Stocked products are blanks (semi-finished) for formed inserts

STAN DAR D CUT T ING CONDIT IONS

Wide grooving
Hardness Cutting speed
ISO Workpiece material Grade
(HB) Vc (sfm)
Alloy steel
< 300 AH725 165 - 590
(4140, 8620, etc.)

Alloy steel
< 300 UX30 165 - 390
(4140, 8620, etc.)

Groove width: W (in)

PSGM type insert
0.394 0.590 0.787 0.984
Feed: f (ipr) 0.008 - 0.016 0.008 - 0.016 0.012 - 0.020 0.012 - 0.020

Forming
Hardness Cutting speed
ISO Workpiece material Grade
(HB) Vc (sfm)
Steel
< 200 UX30 165 - 490
(1045, 1055, etc.)

Alloy steel
< 300 UX30 165 - 390
(4140, 8620, etc.)

Stainless steel
< 200 UX30 165 - 390
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

- TH10 165 - 490
(Class 25, Class 30, etc.)

Ductile cast iron

- TH10 165 - 390
(60-40-18, 60-55-06, etc.)

Aluminum alloy
- TH10 330 - 1640
(Si < 12%, etc.)

Spare parts for internal coolant supply attachment

(Order separately) 4

No. Parts name Designation Note

1
1 Body FPGR... -
2 Insert PSGM... -
3
3 Coolant supply attachment SGCU-341 - 2
Commercial items G 1/8 thread
4 Connector
can be used NPT 1/8 thread

Tungaloy C141
 MillLine

www.tungaloyamerica.com
MILLING

High-Feed Milling D002

Shoulder Milling D032

Face Milling D096

Slot Milling D126

Prof ile Milling D140

Multi-Functional Milling D168

Milling Inser t D212

Tungaloy D001
MillLine - High-Fe ed Milling
Inch Metric

D004
EXH
High-feed endmills
ø0.394" - ø0.625" (ø10 - ø16 mm)
20° max. ap 0.031" (0.8 mm)

D008
Super high-feed milling cutters with 4-cornered double-sided inserts
ø0.625" - ø6.000"
15° max. ap 0.059"

D 016
Super high-feed cutters for profile milling with rigid clamping
ø1.000" - ø2.000"
20° max. ap 0.157"

D 021
Super high-feed cutters for face milling with 8-cornered double-sided inserts
ø2.000" - ø6.000"
13° max. ap 0.079"

D 024
Super high-feed milling cutters for large depths of cut

14° ø2.000" - ø6.000"

max. ap 0.098"

TXP
D 02 6
High-feed milling cutters with single-sided inserts
10°-20° ø0.750" - ø6.000"
max. ap 0.118"

D181

Endmills with exchangeable heads for reduced tool change time

ø0.375" - ø0.750"

D002 www.tungaloyamerica.com
D o Fe e d

Tungaloy D003
 EXH
High-Feed Milling
Su p e r h i g h f e ed m i l l i ng end m i l l s w i t h cente r c u t t i n g e d ge

A.R. = +20°, R.R. = +12°

øDc1

øDsh6
øDc
ap
20˚ Lf Rs
L
Right hand (R) shown.

Inch Max. ap øDc z øDc1 øDs L Lf ℓs Insert

EXH06R039U0050-02 0.024 0.394 2 0.197 0.500 3.570 1.570 2.000 XXGT06H2...
EXH07R050U0050-02 0.024 0.500 2 0.276 0.500 4.000 2.000 2.000 XXGT07X3...
EXH09R063U0063-02 0.031 0.625 2 0.394 0.625 4.500 2.500 2.000 XXGT09X4...

Metric Max. ap øDc z øDc1 øDs L Lf ℓs Insert

EXH06R010M10.0-02 0.6 10 2 5 10 90 40 50 XXGT06H2...
EXH07R012M12.0-02 0.6 12 2 7 12 98 48 50 XXGT07X3...
EXH09R016M16.0-02 0.8 16 2 10 16 124 64 60 XXGT09X4...

SPARE PARTS
Designation qClamping screw Lubricant Wrench Wrench 1
EXH06R... CSPD-1.8S M-1000 - IP-6F
EXH07R... CSPB-2H M-1000 - IP-6F
EXH09R... CSPB-2.5S M-1000 IP-8D -

Insert

Reference pages
Inserts, Standard cutting conditions → D005

D004 www.tungaloyamerica.com
 INSERT
X XGT EC -M J (C e n te r c u t t i n g e d g e ) XXGT EP-MJ (Peripheral cutting edge)

High-Feed Milling
T A T A

B
B
X XGT FC -A J ( C e n te r c u t t i n g e d g e ) X XGT F P-AJ (Peripheral cutting edge)
T A T A

B
B

P Steel ★
M Stainless ★
K Cast iron ★
N Non-ferrous ★
S Superalloys : First choice
: Second choice
H Hard materials
Coated
DS1200

Max.
AH730

Designation ap A B T

XXGT06H205EC-MJ 0.024 z 0.244 0.193 0.098

XXGT07X305EC-MJ 0.024 z 0.276 0.232 0.118
XXGT09X408EC-MJ 0.031 z 0.350 0.311 0.157
XXGT06H205FC-AJ 0.024 z 0.244 0.193 0.098
XXGT07X305FC-AJ 0.024 z 0.276 0.232 0.118
XXGT09X408FC-AJ 0.031 z 0.350 0.311 0.157
XXGT06H205EP-MJ 0.024 z 0.244 0.201 0.098
XXGT07X305EP-MJ 0.024 z 0.276 0.248 0.118
XXGT09X408EP-MJ 0.031 z 0.350 0.315 0.157
XXGT06H205FP-AJ 0.024 z 0.244 0.201 0.098
XXGT07X305FP-AJ 0.024 z 0.276 0.248 0.118
XXGT09X408FP-AJ 0.031 z 0.350 0.315 0.157
z: Line up
STA NDA RD CUT TING CONDITIONS
Shoulder milling, Slotting
Workpiece Carbon steels and Alloy steels and Aluminum alloys Aluminum alloys
Stainless steels Cast irons
material alloy steels prehardened steels (Si < 13%) (Si ≥ 13%)
Hardness < 30HRC 30 ~ 40HRC < 250HB - - -
Cutting speed Vc = 330 - 1,000 sfm Vc = 330~820 sfm Vc = 330 - 1,000 sfm Vc = 330 - 1,000 sfm Vc = 330 - 1,650 sfm Vc = 330 - 1,000sfm
No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf
Conditions
rpm ipm rpm ipm rpm ipm rpm ipm rpm ipm rpm ipm
ap

ap

0.394 4770 56 3820 30 4770 56 6360 100 9550 226 6360 125
Tool dia.
0.500 3980 47 3180 25 3980 47 5300 83 7950 188 5300 104
Side cutting Slotting (in)
0.625 2980 35 2380 19 2980 35 3970 62 5960 141 3970 78
ap: Axial depth of cut 0.394 ap < 0.024 ap < 0.020 ap < 0.024 ap < 0.024 ap < 0.024 ap < 0.024
Depth of
0.500 ap < 0.024 ap < 0.020 ap < 0.024 ap < 0.024 ap < 0.024 ap < 0.024
cut
0.625 ap < 0.031 ap < 0.024 ap < 0.031 ap < 0.031 ap < 0.031 ap < 0.031
Plunging
Workpiece Carbon steels and Alloy steels and Aluminum alloys Aluminum alloys
Stainless steels Cast irons
material alloy steels prehardened steels (Si < 13%) (Si ≥ 13%)
Hardness < 30HRC 30 ~ 40HRC < 250HB - - -
Cutting speed Vc = 330 - 1,000 SFM Vc = 330 - 820 SFM Vc = 330 - 1,000 SFM Vc = 330 - 1,000 SFM Vc = 330 - 1,650 SFM Vc = 330 - 1,000 SFM
No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf No. of rev. n Feed speed Vf
Conditions
rpm ipm rpm ipm rpm ipm rpm ipm rpm ipm rpm ipm
0.394 4770 9 3820 6 4770 9 6360 17 9550 30 6360 17
Tool dia.
0.500 3980 8 3180 5 3980 8 5300 15 7950 25 5300 15
(in)
0.625 2980 6 2380 4 2980 6 3970 11 5960 19 3970 11
Note:¡In slotting or pocketing where chips tend to stay in the cutting ¡Tool overhang length must be as short as possible to avoid
zone, use an air blast to remove chips for preventing chip recutting. chatter. When the tool overhang length is long, decrease the
¡When chips tend to weld excessively on the cutting edge such as number of revolutions and feed.
in machining aluminum alloys, use a water soluble cutting fluid. ¡Cutting conditions are generally limited by the rigidity and power
¡In the case of cutting a casting skin or a heavily interrupted of the machine and the rigidity of the workpiece. When setting
work surface, decrease the feed per tooth and the maximum the conditions, start from half of the values of the standard
depth of cut to 1/2 to 2/3 times the values shown in the table. cutting conditions and then increase the value gradually while
making sure that the machine is running normally.

Tungaloy D005
 A PPLICATION R A NGE
Shoulder
High-Feed Milling
milling Slotting Plunging Drilling
(Helical feed) Enlarging hole
Drilling

Ramping

H1
θ°
He

H
Hp

Hp
>
+1, +2

Max. cutting
Max. depth Max.depth Max. cutting
width in
Max. Min. Max.
width in Max.depth
Tool dia. of drilling ramping machinable machinable of boring
of cut plunging angle hole dia. hole dia. enlarging hole
Inch øDc ap H W θ° D1 D2 ae H1
EXH06R039U0050-02 0.394 0.236 0.197 0.197 5 0.472 0.748 0.276 1.250

EXH07R050U0050-02 0.500 0.236 0.236 0.236 5 0.551 0.906 0.354 1.420

EXH09R063U0063-02 0.625 0.315 0.315 0.315 5 0.709 1.220 0.492 1.890

Max. cutting
Max.depth Max.
Max. depth cutting Max. Min. Max.
width in Max.depth
Tool dia. width in ramping machinable machinable
of cut of drilling of boring
plunging angle hole dia. hole dia. enlarging hole
Metric øDc ap H W θ° D1 D2 ae H1
EXH06R010M10.0-02 10 0.6 5 5 5 12 19 7 30

EXH07R012M12.0-02 12 0.6 6 6 5 14 23 9 36

EXH09R016M16.0-02 16 0.8 8 8 5 18 31 12.5 48

TOOL GEOME TRY FOR PROGR A MMING

When using CAD/CAM, please program it for radius cutter.
The following table shows actual cutting edge geometry and
amount of unfinished work cut.
(Max. depth of cut)

Corner
of insert t: Amount
20˚ of uncut
rε
ap

W Corner radius in
programming R

Max. Corner
Corner Amount
depth Width radius in
of insert of uncut
of cut programming
Inch øDc ap rε W t R
0.028 R.020
EXH06R039U0050-02 0.394 0.024 0.020 0.098
0.024 R.039

0.028 R.020
EXH07R050U0050-02 0.500 0.024 0.020 0.098
0.024 R.039
0.031 R.020
EXH09R063U0063-02 0.625 0.031 0.031 0.118 0.028 R.039
0.024 R.060
Max. Corner Corner
depth Width Amount radius in
of cut of insert of uncut programming
Metric øDc ap rε W t R
0.7 R0.5
EXH06R010M10.0-02 10 0.6 0.5 2.5
0.6 R1.0

0.7 R0.5
EXH07R012M12.0-02 12 0.6 0.5 2.5
0.6 R1.0
0.8 R0.5
EXH09R016M16.0-02 16 0.8 0.8 3 0.7 R1.0
0.6 R1.5

D006 www.tungaloyamerica.com
 High-Feed Milling
MEMO

Tungaloy D007
 TXN 03
High-Feed Milling
S u p e r h i g h f e e d m i l l i n g c u t te r s w i t h d o u b l e s i d e d i n s e r t s w i t h 4 e d g e s
A.R. = +6°, R.R. = +12° ~ 13°
øDb
ød

b
a

R
Lf

ap
κ°
øDc1
øDc

Inch Max. ap øDc z øDc1 øDb ød ℓ Lf b a κ° lb Air hole Insert

TXN03R150U0050A05 0.039 1.500 5 1.248 1.460 0.500 0.750 1.575 0.160 0.252 17 0.530 with LNMU03...
TXN03R150U0050A06 0.039 1.500 6 1.248 1.380 0.500 0.600 1.575 0.160 0.252 17 0.510 with LNMU03...
TXN03R200U0075A05 0.039 2.000 5 1.718 1.693 0.750 0.750 1.969 0.197 0.315 17 1.100 with LNMU03...
TXN03R200U0075A08 0.039 2.000 8 1.718 1.693 0.750 0.750 1.969 0.197 0.315 17 1.100 with LNMU03...
TXN03R200U0075A10 0.039 2.000 10 1.718 1.693 0.750 0.750 1.969 0.197 0.315 17 1.100 with LNMU03...

SPARE PARTS
Designation Clamping screw Lubricant Wrench Center bolt
(Optional parts)
TXN03... CSPB-2.5 M-1000 IP-8D (C0.375X1.125H)

E X N 03
Super high feed milling endmills with double sided inserts with 4 edges
A.R. = +6°, R.R. = +5° ~ +11°
øDc1
øDc

øDs
Fig.1
κ° Lf Rs
ap L
Fig.2

Inch Max. ap øDc z øDc1 øDs L Lf ℓs κ° lb Air hole Insert Fig.

EXN03R062U0062-02 0.039 0.625 2 0.372 0.625 4.000 1.250 2.750 15 0.310 with LNMU03... 1
EXN03R062U0062-02L 0.039 0.625 2 0.372 0.625 6.000 2.000 4.000 15 0.460 with LNMU03... 1
EXN03R068U0062-02 0.039 0.688 2 0.434 0.625 4.000 1.250 2.750 17 0.310 with LNMU03... 1
EXN03R068U0062-02L 0.039 0.688 2 0.434 0.625 6.000 1.000 5.000 17 0.490 with LNMU03... 1
EXN03R075U0075-02 0.039 0.750 2 0.495 0.750 5.000 2.000 3.000 17 0.550 with LNMU03... 1
EXN03R075U0075-03 0.039 0.750 3 0.495 0.750 5.000 2.000 3.000 17 0.550 with LNMU03... 1
EXN03R075U0075-03L 0.039 0.750 3 0.495 0.750 6.500 3.500 3.000 17 0.710 with LNMU03... 1
EXN03R075U0075-03-C 0.039 0.750 3 0.494 0.750 5.000 2.000 3.000 17 0.660 with LNMU03... 2
EXN03R087U0075-02 0.039 0.875 2 0.621 0.750 5.000 2.000 3.000 17 0.570 with LNMU03... 1
EXN03R087U0075-03 0.039 0.875 3 0.621 0.750 5.000 2.000 3.000 17 0.570 with LNMU03... 1
EXN03R087U0075-03L 0.039 0.875 3 0.621 0.750 6.500 1.250 5.250 17 0.750 with LNMU03... 1
EXN03R087U0075-03-C 0.039 0.875 3 0.634 0.750 5.000 2.000 3.000 17 0.660 with LNMU03... 2
EXN03R100U0100-04 0.039 1.000 4 0.746 1.000 5.500 2.500 3.000 17 1.080 with LNMU03... 1
EXN03R100U0100-04L 0.039 1.000 4 0.746 1.000 7.000 4.000 3.000 17 1.340 with LNMU03... 1
EXN03R100U0100-05 0.039 1.000 5 0.746 1.000 5.500 2.500 3.000 17 1.080 with LNMU03... 1
EXN03R100U0100-05-C 0.039 1.000 5 0.756 1.000 5.500 2.500 3.000 17 1.100 with LNMU03... 2
EXN03R112U0100-04 0.039 1.125 4 0.871 1.000 5.500 2.500 3.000 17 1.120 with LNMU03... 1
EXN03R112U0100-04L 0.039 1.125 4 0.871 1.000 7.000 1.500 5.500 17 1.460 with LNMU03... 1
EXN03R112U0100-05 0.039 1.125 5 0.871 1.000 5.500 2.500 3.000 17 1.120 with LNMU03... 1
EXN03R125U0125-05 0.039 1.250 5 0.997 1.250 6.000 3.000 3.000 17 1.870 with LNMU03... 1
EXN03R125U0125-05L 0.039 1.250 5 0.997 1.250 8.000 5.000 3.000 17 2.430 with LNMU03... 1
EXN03R125U0125-06 0.039 1.250 6 0.997 1.250 6.000 3.000 3.000 17 1.850 with LNMU03... 1
EXN03R125U0125-06-C 0.039 1.250 6 1.008 1.250 6.000 3.000 3.000 17 1.760 with LNMU03... 2

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EXN03... CSPB-2.5 M-1000 IP-8D

Reference pages
Inserts → D009, Standard cutting conditions → D010 - D011

D008 www.tungaloyamerica.com
HX N 03-M

High-Feed Milling
S u p e r h i g h f e e d m i l l i ng end m i l l s ( D o f eed ) w i t h Tu n gF l ex

A.R. = +6°, R.R. = +5° ~ +11°

L6
Lf Ts
C T
A

øDc1

øD3
øDc
ap A A-A cross section
κ°
Metric Max. ap øDc z øDc1 L6 Lf C T øD3 κ° Ts Kg Air hole Insert
HXN03R016MM08-02 1 16 2 9.5 42 25 8 10 12.8 15 M8 0.03 with LNMU03...
HXN03R018MM08-02 1 18 2 11.5 42 25 8 10 14.5 17 M8 0.04 with LNMU03...
HXN03R020MM10-03 1 20 3 13.5 49 30 10 15 17.8 17 M10 0.06 with LNMU03...
HXN03R020MM10-04 1 20 4 13.5 49 30 10 15 17.8 17 M10 0.06 with LNMU03...
HXN03R022MM10-03 1 22 3 15.5 49 30 10 15 17.8 17 M10 0.06 with LNMU03...
HXN03R022MM10-04 1 22 4 15.5 49 30 10 15 17.8 17 M10 0.07 with LNMU03...
HXN03R025MM12-04 1 25 4 18.5 57 35 10 17 20.8 17 M12 0.1 with LNMU03...
HXN03R025MM12-05 1 25 5 18.5 57 35 10 17 20.8 17 M12 0.11 with LNMU03...
HXN03R028MM12-04 1 28 4 21.5 57 35 10 17 23 17 M12 0.12 with LNMU03...
HXN03R028MM12-05 1 28 5 21.5 57 35 10 17 23 17 M12 0.12 with LNMU03...
HXN03R030MM16-04 1 30 4 23.5 63 40 12 22 28.8 17 M16 0.19 with LNMU03...
HXN03R030MM16-05 1 30 5 23.5 63 40 12 22 28.8 17 M16 0.2 with LNMU03...
HXN03R032MM16-05 1 32 5 25.5 63 40 12 22 28.8 17 M16 0.2 with LNMU03...
HXN03R032MM16-06 1 32 6 25.5 63 40 12 22 28.8 17 M16 0.21 with LNMU03...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HXN03... CSPB-2.5 M-1000 IP-8D

INSERT
LNMU03-MJ (for general purpose) LNMU03-ML (for low cutting force) LNGU03-MH (for robust cutting edges)
B T B T B T
rε A rε rε
A A
ap

ap

ap

P Steel   
M Stainless  
K Cast iron  
N Non-ferrous
S Superalloys   : First choice
H Hard materials    : Second choice
Coated
AH8005
AH3035
AH8015

Max.
AH725
AH130

Designation rε ap A B T

LNMU0303ZER-MJ 0.047 0.039 z z z z 0.126 0.236 0.169

LNMU0303ZER-ML 0.047 0.039 z z z z 0.126 0.236 0.169
LNGU0303ZER-MH 0.047 0.039 z z 0.126 0.236 0.169
z: Line up

Reference pages
Standard cutting conditions → D010 - D011

Tungaloy D009
 S TA NDA R D C U T TI N G C O N D ITI O N S T X N 0 3 / E X N 0 3 / H X N 0 3
High-Feed Milling Cutting Feed per tooth: fz (ipt)
Chip- speed Tool dia.: øDc (in) ø0.625", z=2 ø0.688", z=2 ø0.750"
ISO Workpiece material Hardness Priority Grade breaker Vc Vf
ø0.620~ 0.870ø1.000~ 2.000 Plunging n Vf n Vf n
(sfm) z=3 z=4
0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
~ 300HB First choice AH3035 MJ 330 - 990 0.004
Carbon steels 0.047 0.059 Vc = 660 sfm, fz = 0.03 ipt
1045, 1055, etc. for wear 0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
~ 300HB AH8015 MJ 330 - 990 0.004
resistance 0.047 0.059 Vc = 660 sfm, fz = 0.03 ipt
0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
~ 300HB First choice AH3035 MJ 330 - 990 0.004
Alloy steels 0.047 0.059 Vc = 660 sfm, fz = 0.03 ipt
4140, SCr415, etc. for wear 0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
~ 300HB AH8015 MJ 330 - 990 0.004
resistance 0.047 0.059 Vc = 660 sfm, fz = 0.03 ipt
30 ~ 0.020 - 0.020 - 3,060 180 2,780 170 2,550 150 230
First choice AH3035 ML 330 - 660 0.004
40HRC 0.039 0.039 Vc = 500 sfm, fz = 0.03 ipt
Prehardened steels 30 ~ for impact 0.020 - 0.020 - 3,060 180 2,780 170 2,550 150 230
AH3035 MJ 330 - 660 0.004
NAK80, PX5, etc. 40HRC resistance 0.047 0.059 Vc = 500 sfm, fz = 0.03 ipt
30 ~ for wear 0.020 - 0.020 - 3,060 180 2,780 170 2,550 150 230
AH8015 ML 330 - 660 0.004
40HRC resistance 0.039 0.039 Vc = 500 sfm, fz = 0.03 ipt
0.012 - 0.012 - 2,510 100 2,280 90 2,090 80 130
~ 200HB First choice AH3035 ML 330 - 490 0.003
Stainless steels 0.028 0.028 Vc = 410 sfm, fz = 0.02 ipt
    304, 316, etc. for impact 0.012 - 0.012 - 2,510 100 2,280 90 2,090 80 130
~ 200HB AH3035 MJ 330 - 490 0.003
resistance 0.031 0.031 Vc= 410 sfm, fz = 0.02 ipt
150 ~ 0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
First choice AH725 MJ 330 - 990 0.004
Gray cast irons 250HB 0.047 0.059 Vc= 660 sfm, fz = 0.03 ipt
No.250B, etc. 150 ~ for wear 0.020 - 0.020 - 4,040 240 3,670 220 3,360 200 300
AH8015 MJ 330 - 990 0.004
250HB resistance 0.047 0.059 Vc = 660 sfm, fz = 0.03 ipt
150 ~ 0.020 - 0.020 - 3,610 220 3,280 200 3,010 180 270
First choice AH725 MJ 260 - 660 0.004
Ductile cast irons 250HB 0.047 0.059 Vc = 590 sfm, fz = 0.03 ipt
65-45-12, etc. 150 ~ for wear 0.020 - 0.020 - 3,610 220 3,280 200 3,010 180 270
AH8015 MJ 260 - 660 0.004
250HB resistance 0.047 0.059 Vc = 590 sfm, fz = 0.03 ipt
0.012 - 0.012 - 920 37 830 33 760 30 46
~ 40HRC First choice AH130 ML 100 - 200 0.003
Titanium alloys 0.028 0.028 Vc = 150 sfm, fz = 0.02 ipt
Ti-6AI-4V, etc. for impact 0.012 - 0.012 - 920 37 830 33 760 30 46
~ 40HRC AH130 MJ 100 - 200 0.003
resistance 0.028 0.028 Vc = 150 sfm, fz = 0.02 ipt
0.004 - 0.004 - 730 12 670 11 610 10 15
~ 40HRC First choice AH725 ML 70 - 170 0.002
Heat-resistant alloys 0.012 0.012 Vc = 120 sfm, fz = 0.008 ipt
Inconel, Hastelloy, etc. for wear 0.004 - 0.004 - 730 12 670 11 610 10 15
~ 40HRC AH8015 ML 70 - 170 0.002
resistance 0.012 0.012 Vc = 120 sfm, fz = 0.008 ipt
40 ~ 0.004 - 0.004 - 2,320 56 2,110 51 1,940 47 70
First choice AH8015 MJ 260 - 490 0.002
Hot mold steel 50HRC 0.020 0.020 Vc = 380 sfm, fz = 0.012 ipt
HB, etc. 50 ~ for impact 0.004 - 0.004 - 2,320 37 2,110 34 1,940 31 47
resistance AH3035 MJ 260 - 490 0.002
60HRC 0.012 0.012 Vc = 380 sfm, fz = 0.008 ipt
50 ~ 0.002 - 0.002 - 1,220 12 1,110 11 1,020 10 15
First choice AH8015 MJ 160 - 230 0.001
Cold mold steel 60HRC 0.008 0.008 Vc = 200 sfm, fz = 0.005 ipt
D2, etc. 50 ~ for impact 0.001 - 0.001 - 1,220 4 1,110 3 1,020 3 5
resistance AH725 MJ 160 - 230 0.001
60HRC 0.002 0.003 Vc = 200 sfm, fz = 0.0015 ipt

When chips stay in the cutting zone during slotting or pocketing, use air Tool overhang length must be as short as possible to avoid chatter. When
blast to remove chips from the work area. the tool overhang length is long, decrease the number of revolutions and
feed.

CAUTION A RY POINTS IN USE

The use of a standard or long shank Tool geometry for programming
When using a long shank, please lower the cutting When programming for CAM, the tool should be considered
conditions (Vc, fz, ap) to 70% of the maximum conditions as a radius cutters. Usually, the corner radius should be set
for the standard shank. as R = 0.060". If a larger radius is used, overcutting will occur.
The following table shows the amount left as uncut (t1) and
0.040 overcut (t2).
Max. depth of cut

Standard shank
Vc = 330 - 980 sfm
Depth of cut: ap (in)

0.028 Amount left

as overcut
max. ap

Amount left t2
0.020 as uncut
Long shank t1
rε
Vc = 260 - 650 sfm 17°
0.012 w R t1 R
Corner R when
programming
Corner R
0 Max. depth Corner when
Amount left Amount left
0.020 0.030 0.040 0.060 of cut radius as uncut as overcut
W (in) program-
Feed per tooth: fz (ipt) max. ap rε ming t1 t2
0.039 0.024 -
Tool dia.: øDc = ø0.625 - 1.250" L/D ratio of overhang 0.060 0.020 -
0.039 0.047 0.118
Workpiece material: 1055 Standard shank: L/D ≤ 3 0.079 0.010 0.003
0.098 0.006 0.010
(200HB) Long shank: L/D = 4
Each value in table is calculated theoretically at the maximum condition.

D010 www.tungaloyamerica.com
 Tool dia.: øDc (in), Number of revolutions: n (rpm-1), Feed speed: Vf (ipm), Max. depth of cut: ap = 0.039", No. of teeth: z

High-Feed Milling
ø.875" ø1.000" ø1.125" ø1.250" ø1.500" ø2.000"
Vf Vf Vf Vf Vf Vf
n n n n n n
Z=2 Z=3 Z=4 Z=5 Z=4 Z=5 Z=5 Z=6 Z=5 Z=6 Z=5 Z=8
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc = 660 sfm, fz = 0.04 ipt
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc = 660 sfm, fz = 0.04 ipt
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc = 660 sfm, fz = 0.04 ipt
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc= 500 sfm, fz = 0.03 ipt
2,250 140 200 1,910 230 290 1,700 200 260 1,530 230 280 1,270 190 230 960 140 230
Vc = 500 sfm, fz = 0.03 ipt
2,250 140 200 1,910 310 380 1,700 270 340 1,530 310 370 1,270 250 300 960 190 310
Vc = 500 sfm, fz = 0.04 ipt
2,250 140 200 1,910 230 290 1,700 200 260 1,530 230 280 1,270 190 230 960 140 230
Vc = 500 sfm, fz = 0.03 ipt
1,840 70 110 1,570 130 160 1,390 110 140 1,250 130 150 1,040 100 120 780 80 120
Vc = 410 sfm, fz = 0.02 ipt
1,840 70 110 1,570 130 160 1,390 110 140 1,250 130 150 1,040 100 120 780 80 120
Vc = 410 sfm, fz = 0.02 ipt
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc = 660 sfm, fz = 0.04 ipt
2,970 180 270 2,520 400 500 2,240 360 450 2,020 400 480 1,680 340 400 1,260 250 400
Vc = 660 sfm, fz = 0.04 ipt
2,650 160 240 2,250 360 450 2,000 320 400 1,800 360 430 1,500 300 360 1,130 230 360
Vc = 590 sfm, fz = 0.04 ipt
2,650 160 240 2,250 360 450 2,000 320 400 1,800 360 430 1,500 300 360 1,130 230 360
Vc= 590 sfm, fz = 0.04 ipt
670 27 40 570 46 57 510 41 51 460 46 55 380 38 46 290 29 46
Vc = 150 sfm, fz = 0.02 ipt
670 27 40 570 46 57 510 41 51 460 46 55 380 38 46 290 29 46
Vc = 150 sfm, fz = 0.02 ipt
540 9 13 460 15 18 410 13 16 370 15 18 310 12 15 230 9 15
Vc = 120 sfm, fz = 0.008 ipt
540 9 13 460 15 18 410 13 16 370 15 18 310 12 15 230 9 15
Vc = 120 sfm, fz = 0.008 ipt
1,710 41 62 1,450 70 87 1,290 62 77 1,160 70 84 970 58 70 730 44 70
Vc = 380 sfm, fz = 0.012 ipt
1,710 27 41 1,450 46 58 1,290 41 52 1,160 46 56 970 39 47 730 29 47
Vc = 380 sfm, fz = 0.008 ipt
900 9 14 760 15 19 680 14 17 610 15 18 510 13 15 380 10 15
Vc = 200 sfm, fz = 0.005 ipt
900 3 4 760 6 8 680 5 7 610 6 7 510 5 6 380 4 6
Vc = 200 sfm, fz = 0.002 ipt

The above table shows the conditions for standard shank Cutting conditions are generally limited by the rigidity and
type cutters. When using long shank type cutters, the number power of the machine and the rigidity of the workpiece.
of teeth may be different. In this case, the cutting conditions When setting the conditions, start from half of the values of
should be changed by referring to: “The use of standard or the standard cutting conditions and then increase the value
long shanks” shown in previous page. gradually while making sure the machine is running normally.

A PPLICATION R A NGE
Shoulder Small depth Plunging Drilling Enlarged hole
milling Slotting Ramping plunging (Helical feed)
Hp

Hp

θ° Traversing
A

>
He
ø+1, ø+2
Max. cutting Max. Max. cutting
Max. depth Max. ramping Max. plunging width in Min.machinable width in enlarged
Tool dia. of cut angle depth hole dia.
machinable
plunging hole dia. hole
Inch øDc Max ap θ° A W øD1 øD2 ae
EXN03R062U0062... 0.625 0.039 2.1 0.012 0.138 0.866 1.181 0.492
EXN03R068U0062... 0.688 0.039 1.7 0.012 0.138 1.024 1.339 0.571
EXN03R075U0075... 0.750 0.039 1.4 0.012 0.138 1.181 1.496 0.650
EXN03R087U0075... 0.875 0.039 1.2 0.012 0.138 1.339 1.654 0.728
EXN03R100U0100... 1.000 0.039 1.0 0.012 0.138 1.575 1.890 0.846
EXN03R112U0100... 1.125 0.039 0.8 0.012 0.138 1.811 2.126 0.965
EXN03R125U0125... 1.250 0.039 0.7 0.012 0.138 2.126 2.441 1.122
TXN03R150U0075... 1.500 0.039 0.5 0.012 0.138 2.750 3.070 1.437
TXN03R200U0075... 2.000 0.039 0.4 0.012 0.138 3.540 3.858 1.830
· For øDc above 1.300", slot milling, ramping or contouring is not recommended as chips may be re-cut.

Tungaloy D011
 TX N 06
High-Feed Milling
S u p e r h i g h f e e d m i l l i n g c u t te r s w i t h d o u b l e s i d e d i n s e r t s w i t h 4 e d g e s

øDb
ød
a

ℓ
b
Lf

ap
øDc1
15°
øDc

Inch Max. ap øDc z øDc1 øDb Lf ød ℓ a b lb Air hole Insert

TXN06R200U0075A04 0.059 2.000 4 1.513 1.850 1.969 0.750 0.750 0.315 0.197 0.970 with LN*U06...
TXN06R200U0075A05 0.059 2.000 5 1.513 1.850 1.969 0.750 0.750 0.315 0.197 0.990 with LN*U06...
TXN06R250U0075A04 0.059 2.500 4 2.012 2.323 1.969 0.750 0.750 0.315 0.197 1.740 with LN*U06...
TXN06R250U0075A06 0.059 2.500 6 2.012 2.323 1.969 0.750 0.750 0.315 0.197 1.760 with LN*U06...
TXN06R300U0100A05 0.059 3.000 5 2.512 2.835 2.480 1.000 1.049 0.374 0.236 3.130 with LN*U06...
TXN06R300U0100A07 0.059 3.000 7 2.512 2.835 2.480 1.000 1.049 0.374 0.236 3.280 with LN*U06...
TXN06R400U0150A06 0.059 4.000 6 3.512 3.819 2.480 1.500 1.610 0.626 0.394 4.850 with LN*U06...
TXN06R400U0150A10 0.059 4.000 10 3.512 3.819 2.480 1.500 1.610 0.626 0.394 4.850 with LN*U06...
TXN06R500U0150A08 0.059 5.000 8 4.512 3.819 2.480 1.500 1.610 0.626 0.394 7.050 with LN*U06...
TXN06R500U0150A12 0.059 5.000 12 4.512 3.819 2.480 1.500 1.610 0.626 0.394 7.280 with LN*U06...
TXN06R600U0200A10 0.059 6.000 10 5.512 4.331 2.480 2.000 1.496 0.748 0.433 9.480 with LN*U06...
TXN06R600U0200A14 0.059 6.000 14 5.512 4.331 2.480 2.000 1.496 0.748 0.433 9.260 with LN*U06...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Center bolt
(Optional parts)
TXN06R200U - 500U CSPB-5 H-TB2W M-1000 BLDIP20/S7 (C0.375X1.125H)
TXN06R600U... CSPB-5 H-TB2W M-1000 BLDIP20/M7 (TMBA-0.750H)

Reference pages
Inserts → D013, Standard cutting conditions → D014 - D015

D012 www.tungaloyamerica.com
E X N 06

High-Feed Milling
Super high feed milling endmills with double sided inserts with 4 edges

A.R. = +10°, R.R. = -2° +6°

øDc1

øDs
øDc
15° Lf Rs
L
ap
Inch Max. ap øDc z øDc1 øDs L Lf ℓs lb Air hole Insert
EXN06R125U0125W02 0.059 1.250 2 0.766 1.250 5.281 3.000 2.281 1.540 with LN*U06...
EXN06R125U0125-02L 0.059 1.250 2 0.766 1.250 8.000 5.000 3.000 2.360 with LN*U06...
EXN06R150U0125W03 0.059 1.500 3 1.014 1.250 5.781 3.500 2.281 1.830 with LN*U06...
EXN06R150U0125-03L 0.059 1.500 3 1.014 1.250 10.000 2.000 8.000 3.310 with LN*U06...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EXN06... CSPB-5 M-1000 IP-20D

INSERT
L N M U 06-M J L N M U 0 6 -M L
B T B T

ap
ap

A rε
A rε

L N G U 06-M H L N G U 0 6 -W ( 2 c u t t in g e d g e s)
B T B T
ap

ap

A rε bs A rε
P Steel   
M Stainless  
K Cast iron   
N Non-ferrous
S Superalloys   : First choice
H Hard materials    : Second choice
Coated
AH8005
AH3035
AH8015

Max.
AH725
AH130
AH120

Designation rε ap A B T bs

LNMU06X5ZER-MJ 0.079 0.059 z z z z z 0.236 0.472 0.276 -

LNMU06X5ZER-ML 0.079 0.059 z z z z z 0.236 0.472 0.276 -
LNGU06X5ZER-MH 0.079 0.059 z z 0.236 0.472 0.276 -
LNGU06X5ZER-W 0.079 0.059 z 0.236 0.472 0.276 0.142

z: Line up

Reference pages
Standard cutting conditions → D014 - D015

Tungaloy D013
 STA NDA RD CUT TING CONDITIONS T X N 0 6 / E X N 0 6
Cutting Feed per tooth
High-Feed Milling
speed fz (ipt)
Chip- Feed ø1.250 ", z = 2 ø1.500 ", z = 2 ø2.000 "
ISO Work material Hardness Priority Grades breaker Tool dia:
Vc when
øDc (in) Vf
(sfm) plunging n Vf n Vf n
ø1.250 ~ ø6.000 fz (ipt) z=4 z=5
Carbon steels First choice AH3035 MJ 0.020 - 2,020 162 1,680 134 1,261 202 252
~ 300HB 330 - 990 0.006
1045, 1055, etc. for wear resistance AH8015 MJ 0.059
Alloy steels First choice AH3035 MJ 0.020 - 2,018 161 1,682 135 1,261 202 252
~ 300HB 330 - 990 0.006
4140, SCr415, etc. for wear resistance AH8015 MJ 0.059
30 ~ 0.020 - 1,529 92 1,274 76 955 115 143
First choice AH3035 ML 330 - 660 0.006
40HRC 0.039
Prehardened steels 30 ~ 0.020 - 1,529 122 1,274 102 955 153 191
for impact resistance AH3035 MJ 330 - 660 0.006
NAK80, PX5, etc. 40HRC 0.059
30 ~ 0.020 - 1,529 92 1,274 76 955 115 143
for wear resistance AH8015 ML 330 - 660 0.006
40HRC 0.039
0.012 - 1,254 50 1,045 42 783 63 78
~ 200HB First choice AH3035 ML 330 - 490 0.004
Stainless steels 0.028
304, 316, etc. 0.012 - 1,254 50 1,045 42 783 63 78
~ 200HB for impact resistance AH3035 MJ 330 - 490 0.004
0.031
150 ~ 0.020 - 2,018 161 1,682 135 1,261 202 252
First choice AH120 MJ 330 - 990 0.006
Gray cast irons 250HB 0.059
No.250B, etc. 150 ~ 0.020 - 2,018 161 1,682 135 1,261 202 252
for wear resistance AH8015 MJ 330 - 990 0.006
250HB 0.059
150 ~ 0.020 - 1,406 113 1,172 94 879 141 176
First choice AH120 MJ 260 - 660 0.006
Ductile cast irons 250HB 0.059
65-45-12, etc. 150 ~ 0.020 - 1,406 113 1,172 94 879 141 176
for wear resistance AH8015 MJ 260 - 660 0.006
250HB 0.059
Titanium alloys First choice AH130 ML 0.012 - 459 18 382 15 287 23 29
~ 40HRC 100 - 200 0.003
Ti-6AI-4V, etc. for impact resistance AH130 MJ 0.028
Heat-resistant alloys First choice AH725 ML 0.004 - 367 6 306 5 229 7 9
~ 40HRC 70 - 170 0.002
Inconel, Hastelloy, etc. for wear resistance AH8015 ML 0.012
40 ~ 0.004 - 1,162 28 968 23 726 35 44
First choice AH8015 MJ 260 - 490 0.002
Hot mold steel 50HRC 0.020
HB, etc. 40 ~ 0.004 - 1,162 19 968 15 726 23 29
for impact resistance AH3035 MJ 260 - 490 0.002
50HRC 0.012
50 ~ 0.002 - 611 6 510 5 382 8 10
First choice AH8015 MJ 160 - 230 0.001
Cold mold steel 60HRC 0.008
D2, etc. 50 ~ 0.001 - 611 2 510 2 382 3 4
for impact resistance AH725 MJ 160 - 230 0.001
60HRC 0.003

When chips stay in the cutting zone during slotting or pocketing, use air Tool overhang length must be as short as possible to avoid chatter. When
blast to remove chips from the work area. the tool overhang length is long, decrease the number of revolutions and
feed.

CAUTION A RY POINTS IN USE

The usage of a standard & long shank Tool geometry for programming
When using a long shank, please lower the cutting When programming for CAM, the tool should be considered
conditions (Vc, fz, ap) to 70% of the maximum conditions as a radius cutters. Usually, the corner radius should be
for the standard shank. set as R = 0.118". If a larger radius is used, overcutting will
occur. The following table shows the amount left as uncut (t1)
0.060 and overcut (t2).
Max. depth of cut

Standard shank
Vc = 330 - 980 sfm
Depth of cut: ap (in)

Amount left
as overcut
0.040 t2
max. ap

rε
Long shank 15°
Vc = 260 - 650 sfm R
0.020 w t1 R
t1
Amount left Corner R when
as uncut programming

Max. depth Corner Corner R Amount left Amount left

0 of cut when as uncut as overcut
0.020 0.040 0.060 0.080 max. radius W (in) program-
Feed per tooth: fz (ipt) ap(in) rε ming t1 t2
0.079 0.040 -
Tool dia.: øDc = ø1.250" - 1.500" L/D ratio of overhang 0.059 0.079 0.236 0.118 0.030 -
Workpiece material: 1055 Standard shank: L/D ≤ 3 0.157 0.021 0.010
(200HB) Long shank: L/D = 4
Each value in table is calculated theoretically at the maximum condition.

D014 www.tungaloyamerica.com
 Tool dia:øDc (in), Number of revolution: n (rpm), Feed speed: Vf (ipm),

High-Feed Milling
Max. depth of cut:ap = 0.059 ", Number of teeth:z
ø2.500 " ø3.000 " ø4.000 " ø5.000 " ø6.000 "
Vf Vf Vf Vf Vf
n n n n n
z=4 z=6 z=5 z=7 z=6 z=10 z=8 z=12 z=10 z=15
1,009 161 202 841 168 235 631 151 252 504 161 242 420 168 252
Vc = 660 sfm, fz = 0.040 ipt
1,009 161 202 841 168 235 631 151 252 504 161 242 420 168 252
Vc = 660 sfm, fz = 0.040 ipt
1,009 161 202 841 168 235 631 151 252 504 161 242 420 168 252
Vc = 500 sfm, fz =0.030 ipt
764 122 153 637 127 178 478 115 191 382 122 183 318 127 191
Vc = 500 sfm, fz = 0.040 ipt
764 92 115 637 96 134 478 86 143 382 92 138 318 96 143
Vc = 500 sfm, fz =0 .030 ipt
627 50 63 522 52 73 392 47 78 313 50 75 261 52 78
Vc = 410 sfm, fz = 0.020 ipt
627 50 63 522 52 73 392 47 78 313 50 75 261 52 78
Vc = 410 sfm, fz = 0.020 ipt
1,009 161 202 841 168 235 631 151 252 504 161 242 420 168 252
Vc = 660 sfm, fz = 0.040 ipt
1,009 161 202 841 168 235 631 151 252 504 161 242 420 168 252
Vc = 660 sfm, fz = 0.040 ipt
703 113 141 586 117 164 439 105 176 352 113 169 293 117 176
Vc = 460 sfm, fz = 0.040 ipt
703 113 141 586 117 164 439 105 176 352 113 169 293 117 176
Vc = 460 sfm, fz = 0.040 ipt
229 18 23 191 19 27 143 17 29 115 18 28 96 19 29
Vc = 150 sfm, fz = 0.020 ipt
183 6 7 153 6 9 115 6 9 92 6 9 76 6 9
Vc = 120 sfm, fz = 0.008 ipt
581 28 35 484 29 41 363 26 44 290 28 42 242 29 44
Vc = 380 sfm, fz = 0.012 ipt
581 19 23 484 19 27 363 17 29 290 19 28 242 19 29
Vc = 380 sfm, fz = 0.012 ipt
306 6 8 255 6 9 191 6 10 153 6 9 127 6 10
Vc = 200 sfm, fz = 0.005 ipt
306 2 3 255 3 4 191 2 4 153 2 4 127 3 4
Vc = 200 sfm, fz = 0.005 ipt

The above table shows the conditions for standard shank Cutting conditions are generally limited by the rigidity and
type cutters. When using long shank type cutters, the number power of the machine and the rigidity of the workpiece.
of teeth may be different. In this case, the cutting conditions When setting the conditions, start from half of the values of
should be changed by referring to: “The usage of standard the standard cutting conditions and then increase the value
and long shanks” shown in previous page. gradually while making sure the machine is running normally.

A PPLICATION R A NGE
Drilling
Shoulder Small depth Enlarged hole
Plunging (Helical feed)
milling plunging Ramping

θ°
Hp

Traversing
A

>
He
ø+1, ø+2

Max. depth Max. ramping Max. plunging Max. cutting Min.machinable Max.machinable Max. cutting
Tool dia. of cut angle depth width in plunging hole dia. hole dia. width in enlarged
hole
Inch øDc Max. ap θ° A W øD1 øD2 ae
EXN06R125U... ø1.250 0.059 2.0º 0.020 0.236 1.830 2.300 0.970
EXN06R150U... ø1.500 0.059 1.5º 0.020 0.236 2.330 2.800 1.220
TXN06R200U... ø2.000 0.059 0.9º 0.020 0.236 3.330 3.800 1.720
TXN06R250U... ø2.500 0.059 0.6º 0.020 0.236 4.330 4.800 2.220
TXN06R300U... ø3.000 0.059 0.5º 0.020 0.236 5.330 5.800 2.720
· For øDc above 4.000", slot milling, ramping or contouring is not recommended as chips may be re-cut.

Tungaloy D015
High-Feed Milling TX LN
R a d i u s c u t te r w i t h d o u b l e - s i d e d i n s e r t w i t h 4 e d g e s
A.R. = +3°, R.R. = -13°
øDb
ød

b
a

R
R R R

Lf
ap
øDc1
øDc

Inch Max. ap øDc z øDc1 øDb Lf ød ℓ a b lb Air hole Insert

TXLN04U1.50B0.50R06 0.157 1.500 6 1.177 1.375 1.574 0.500 0.610 0.258 0.157 0.770 with LNMX04...
TXLN04U2.00B0.75R07 0.157 2.000 7 1.677 1.845 1.969 0.750 0.750 0.315 0.197 0.990 with LNMX04...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Center bolt
(Optional parts)
TXLN04U1.50B0.50R06 CSPD-3 SW6-SD M-1000 BLD IP10/S7 (SR UNF 1/4X3/4 B18.3)
TXLN04U2.00B0.75R07 CSPD-3 SW6-SD M-1000 BLD IP10/S7 (C0.375X1.125H)

EXLN
R a d i u s c u t te r w i t h d o u b l e - s i d e d i n s e r t w i t h 4 e d g e s

A.R. = +3°, R.R. = -12° -14°

øDc1
øDc

øDs
R R R

ap
Lf ℓs
L

Inch Max. ap øDc z øDc1 øDs ℓs Lf L lb Air hole Insert

EXLN04U1.00C1.00R03 0.157 1.000 3 0.685 1.000 3.000 2.500 5.500 1.000 with LNMX04...
EXLN04U1.25C1.25R04 0.157 1.250 4 0.935 1.250 3.000 3.000 6.000 1.800 with LNMX04...
EXLN04U1.25C1.25R05 0.157 1.250 5 0.935 1.250 3.000 3.000 6.000 1.800 with LNMX04...

SPARE PARTS
Designation Clamping screw Mono block type
wrench
EXLN04U... CSPD-3 IP-10D

Reference pages
Inserts → D017, Standard cutting conditions → D018

D016 www.tungaloyamerica.com
HX LN 04-M

High-Feed Milling
R a d i u s c u t te r w i t h d o ub l e- si d ed i nser t w i t h 4 e d ge s , M od u l a r h e a d w i t h m e t r i c t h re a d c on n e c t i on

A.R. = +3°, R.R. = -12° -14°

L6
Lf
C Ts
A T R R R

øDc1

øD3
øDc
ap A A - A cross section

Metric Max. ap øDc z øDc1 L6 Lf C T øD3 Ts Kg Air hole Insert

HXLN04M020M10R02 4 20 2 12 49 30 10 15 18 M10 0.07 with LNMX04...
HXLN04M025M12R03 4 25 3 17 57 35 10 17 21 M12 0.16 with LNMX04...
HXLN04M032M16R04 4 32 4 24 63 40 12 22 29 M16 0.2 with LNMX04...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HXLN04... CSPD-3 M-1000 IP-10D

INSERT
L N M X -M J L N M X -M L
rε rε
B T B T
ap

L N M X -H J ap
T
A
rε
ap

B
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys  : First choice
H Hard materials  : Second choice
Coated
AH3135

Max.
AH120

Designation rε ap A B T

LNMX0405R4-MJ 0.157 0.157 z z - 0.323 0.220

LNMX0405R4-ML 0.157 0.157 z z - 0.323 0.220
LNMX0405ZER-HJ 0.051 0.051 z z 0.169 0.323 0.197
z: Line up

Reference pages
Standard cutting conditions → D018

Tungaloy D017
 STA NDA RD CUT TING CONDITIONS
High-Feed Milling Fo r M J , M L t y p e ( R a d i u s i n s e r t )
Chip- Cutting Feed per
ISO Workpiece material Hardness Priority Grade speed tooth
breaker Vc (sfm) fz (ipt)
Low carbon steels - 300 HB First choice AH3135 MJ 490 - 820 0.0079 - 0.0236
1015, etc. - 300 HB Second choice AH3135 ML 490 - 820 0.0079 - 0.0236

Carbon steels, Alloy steels - 300 HB First choice AH3135 MJ 490 - 820 0.0079 - 0.0236
1055, etc. - 300 HB Second choice AH3135 ML 490 - 820 0.0079 - 0.0236

Prehardened steels 30 - 40 HRC First choice AH3135 MJ 330 - 660 0.0059 - 0.0157
NAK80, PX5, etc. 30 - 40 HRC Second choice AH3135 ML 330 - 660 0.0059 - 0.0157

Stainless steels - 200 HB First choice AH3135 MJ 330 - 660 0.0079 - 0.0236
S30400, etc
- 200 HB Second choice AH3135 ML 330 - 660 0.0079 - 0.0236

Stainless steels - 200 HB First choice AH3135 MJ 330 - 980 0.0079 - 0.0236
S4200, etc
- 200 HB Second choice AH3135 ML 330 - 980 0.0079 - 0.0236

Grey cast irons 150 - 250 HB First choice AH120 MJ 490 - 820 0.0079 - 0.0236
No.250B, No.300B, etc. 150 - 250 HB Second choice AH120 ML 490 - 820 0.0079 - 0.0236

Ductile cast irons 150 - 250 HB First choice AH120 MJ 490 - 820 0.0079 - 0.0236
60-40-18, 80-50-06, etc.
150 - 250 HB Second choice AH120 ML 490 - 820 0.0079 - 0.0236
Titanium alloys
- 40 HRC First choice AH3135 ML 98 - 197 0.0039 - 0.0118
Ti-6Al-4V, etc.
Heat-resistant alloys
- 40 HRC First choice AH120 MJ 33 - 131 0.0039 - 0.0079
Inconel 718, etc.

40 - 50 HRC First choice AH3135 MJ 160 - 490 0.0039 - 0.0118

H13, etc
40 - 50 HRC Second choice AH3135 ML 160 - 490 0.0039 - 0.0118
Hardened steel
50 - 60 HRC First choice AH120 MJ 160 - 230 0.0020 - 0.0059
D2, etc
50 - 60 HRC Second choice AH120 ML 160 - 230 0.0020 - 0.0059

Fo r H J t y p e ( H i g h f e e d i n s e r t )
Cutting Feed per
ISO Workpiece material Hardness Priority Grade Chipbreaker speed tooth
Vc (sfm) fz (ipt)
Low carbon steels First choice AH3135 HJ 490 - 820 0.0197 - 0.059
- 300 HB
C15, C20, etc. Second choice AH120 HJ 490 - 820 0.0197 - 0.059

Carbon steels, Alloy steels First choice AH3135 HJ 490 - 820 0.0197 - 0.059
- 300 HB
1055, etc. AH120 HJ
Second choice 490 - 820 0.0197 - 0.059

Carbon steels, Alloy steels First choice AH3135 HJ 330 - 660 0.0118 - 0.0276
30 - 40 HRC
1055, etc. Second choice AH120 HJ 330 - 660 0.0118 - 0.0276

Stainless steels - 200 HB First choice AH3135 HJ 330 - 660 0.0118 - 0.0276
S30400, etc - 200 HB AH3135 HJ 330 - 980
First choice 0.0118 - 0.0276

Grey cast irons No.250B, No.300B, etc. 150 - 250 HB First choice AH120 HJ 490 - 820 0.0197 - 0.059

Ductile cast irons 60-40-18, 80-50-06, etc. 150 - 250 HB First choice AH120 HJ 490 - 820 0.0197 - 0.059

Titanium alloys
- 40 HRC First choice AH3135 HJ 98 - 197 0.0118 - 0.028
Ti-6Al-4V, etc.
Heat-resistant alloys
- 40 HRC First choice AH120 HJ 33 - 131 0.0039 - 0.0118
Inconel 718, etc.
First choice AH3135 HJ 160 - 490 0.0039 - 0.0197
H13, etc 40 - 50 HRC
Hardened steel Second choice AH120 HJ 160 - 490 0.0039 - 0.0197
D2, etc 50 - 60 HRC First choice AH120 HJ 160 - 230 0.0020 - 0.0079

Note: Recommended cutting conditions are just for reference in general machining.

D018 www.tungaloyamerica.com
 A PPLICATION R A NGE

High-Feed Milling
Shoulder Slotting Ramping Small depth Plunging Drilling Enlarged hole
milling plunging (Helical feed)

Hp

Hp
Traversing
θ°

A
>
He
ø+1, ø+2

Fo r M J, M L t ype
Max. depth of Max. Max. cutting Max. cutting
Tool dia. ramping Max. Min. Max. width in
plunging (in) width in
cut (in) angle plunging (in) machining (in) machining (in) enlarging (in)
Inch øDc ap θ° A W øD1 øD2 ae
EXLN04U1.00C1.00R03 1.000 0.157 3 0.031 0.157 1.535 1.929 0.803
EXLN04U1.25C1.25R04 1.250 0.157 1.9 0.031 0.157 2.047 2.402 1.053
EXLN04U1.25C1.25R05 1.250 0.157 1.9 0.031 0.157 2.047 2.402 1.053
TXLN04U1.50B0.50R06 1.500 0.157 1.2 0.024 0.157 2.511 2.905 1.342
TXLN04U2.00B0.75R07 2.000 0.157 1 0.027 0.157 3.496 3.889 1.842

Max. depth of Max. Max. Max. cutting Max. cutting

Tool dia. ramping plunging Min. Max. width in
width in
cut angle depth machining machining enlarging
plunging
Metric øDc øDc1 ap θ° A W øD1 øD2 ae
HXLN04M020M10R02 20 12 4 4.7 0.8 4 28 38 15

HXLN04M025M12R03 25 17 4 3 0.8 4 38 48 20

HXLN04M032M16R04 32 24 4 2 0.8 4 50 62 27

Fo r H J t ype
Max. depth of Max. Max. cutting Max. cutting
Tool dia. ramping Max. Min. Max. width in
plunging (in) width in
cut (in) angle machining (in) machining (in) enlarging (in)
plunging (in)
Inch øDc ap θ° A W øD1 øD2 ae
EXLN04U1.00C1.00R03 1.000 0.051 3 0.030 0.161 1.496 1.929 0.803
EXLN04U1.25C1.25R04 1.250 0.051 2 0.030 0.161 2.008 2.441 1.053
EXLN04U1.25C1.25R05 1.250 0.051 2 0.030 0.161 2.008 2.441 1.053
TXLN04U1.50B0.50R06 1.500 0.157 1.2 0.024 0.157 2.456 2.905 1.342
TXLN04U2.00B0.75R07 2.000 0.157 1 0.027 0.157 3.456 3.889 1.842

Max. depth of Max. Max. Max. cutting Max. cutting

Tool dia. ramping plunging Min. Max. width in
width in
cut angle depth plunging machining machining enlarging
Metric øDc øDc1 ap θ° A W øD1 øD2 ae
HXLN04M020M10R02 20 12 1.3 4.9 0.75 4.1 27 38 15.5

HXLN04M025M12R03 25 17 1.3 3 0.75 4.1 37 48 20.5

HXLN04M032M16R04 32 24 1.3 2 0.75 4.1 51 62 27.5

TOOL GEOME TRY FOR PROGR A MMING

Max. depth of Programmed Amount left Amount left

Overcut cut W (in) corner R uncut overcut
t2 amount max. ap (in) (in) t1 (in) t2 (in)

0.051 0.161 R0.059 0.031 0

0.051 0.161 R0.079 0.026 0

t1 w R 0.051 0.161 R0.098 0.020 0.002

Corner R when
Uncut amount programming 0.051 0.161 R0.118 0.014 0.008

Tungaloy D019
High-Feed Milling

MEMO

D020 www.tungaloyamerica.com
T XQ

High-Feed Milling
High f e e d c u t te r f o r f ace m i l l i ng

A.R. = +7°, R.R. = -8° ~ -4.5°

øDb
ød

b
a

R
Lf
ap
øDc1 13º
øDc
Inch Max. ap øDc z øDc1 øDb Lf ød ℓ a b Ib Air hole Insert
TXQ12R200U0075A03 0.079 2.000 3 1.362 1.850 1.969 0.750 0.750 0.315 0.197 1.120 with SQMU1206ZSR-MJ
TXQ12R200U0075A04 0.079 2.000 4 1.362 1.850 1.969 0.750 0.750 0.315 0.197 1.120 with SQMU1206ZSR-MJ
TXQ12R250U0075A04 0.079 2.500 4 1.862 2.323 1.969 0.750 0.750 0.315 0.197 1.760 with SQMU1206ZSR-MJ
TXQ12R300U0100A05 0.079 3.000 5 2.362 2.835 1.969 1.000 1.024 0.374 0.236 3.770 with SQMU1206ZSR-MJ
TXQ12R400U0150A06 0.079 4.000 6 3.362 3.780 1.969 1.500 1.457 0.626 0.394 5.710 with SQMU1206ZSR-MJ
TXQ12R500U0150A07 0.079 5.000 7 4.362 3.780 1.969 1.500 1.457 0.626 0.394 7.010 with SQMU1206ZSR-MJ
TXQ12R600U0200A08 0.079 6.000 8 5.37 3.937 2.480 2.000 1.496 0.748 0.433 7.350 with SQMU1206ZSR-MJ

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Center bolt
(Optional parts)
TXQ12R**U0075A... CSPB-4 H-TBS M-1000 BLDIP15/S7 (C0.375X1.125H)
TXQ12R300U0100A05 CSPB-4 H-TBS M-1000 BLDIP15/S7 (C0.500X1.375H)
TXQ12R**U0150A... CSPB-4 H-TBS M-1000 BLDIP15/S7 (TMBA-0.750H)
TXQ12R600U0200A08 CSPB-4 H-TBS M-1000 BLDIP15/S7 (TMBA-M24H)

INSERT
S QM U -M J
ød T
A

rε
P Steel  
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys  : First choice
H Hard materials  : Second choice
Coated

Max.
AH725
AH130
AH120

T3130

Designation rε ap A T ød

SQMU1206ZSR-MJ 0.079 0.079 z z z z 0.461 0.236 0.461

z: Line up

Reference pages
Standard cutting conditions → D022 - D023

Tungaloy D021
 STA NDA RD CUT TING CONDITIONS
Cutting Feed per
High-Feed Milling
ISO Workpiece material Hardness Priority Grade speed tooth
Vc (sfm) fz (ipt)
First choice AH725 330 - 980 0.020 - 0.080
High carbon steels
~ 300HB For wear resistance T3130 330 - 980 0.020 - 0.080
(1045, 1055 etc.)
For impact resistance AH130 330 - 980 0.020 - 0.080
First choice AH725 330 - 660 0.020 - 0.060
Alloyed steels
~ 300HB For wear resistance T3130 330 - 660 0.020 - 0.060
(4140 etc.)
For impact resistance AH130 330 - 660 0.020 - 0.060

Prehardened steels
30 ~ 40HRC - AH725 330 - 660 0.020 - 0.040
(NAK80, PX5, etc.)

Stainless steel
~ 200HB - AH130 330 - 500 0.012 - 0.030
(304, 316 etc.)

Gray cast iron

- - AH120 100 - 300 0.020 - 0.080
(No.25, No.30 etc.)

Ductile cast irons

- - AH120 260 - 660 0.020 - 0.080
(60-40-18, 65-45-12 etc.)

Titanium alloy
~ 40HRC - AH725 100 - 200 0.012 - 0.028
(Ti-6Al-4V etc.)

(H13 etc.) 40 ~ 50HRC - AH725 260 - 43 0.004 - 0.012

Hardened steels
(D2 etc.) 50 ~ 60HRC - AH725 160 - 230 0.001 - 0.003

· Slot or pocket milling is not recommended, since chip re-cutting easily · Cutting conditions are generally limited by the rigidity and power of the
occurs. machine and the rigidity of the workpiece. When setting the conditions, start
· Tool overhang length must be as short as possible to avoid chatter. When from half of the values of the standard cutting conditions and then increase
the tool overhang length is long, decrease the number of revolutions and feed. the value gradually while making sure the machine is running normally.

D022 www.tungaloyamerica.com
 Tool dia.: øDc (in), Number of revolutions: n (rpm), Feed speed: Vf (ipm), Max. depth of cut: ap = 0.079"
ø2.000 ø2.500 ø3.000 ø4.000 ø5.000

High-Feed Milling
n Vf n Vf n Vf n Vf n Vf
1,260 227 1,010 242 790 237 630 227 500 210

Vc = 660 sfm, fz = 0.060 ipt

950 114 750 120 590 118 470 113 380 106

Vc = 500 sfm, fz = 0.040 ipt

950 86 750 90 590 89 470 85 380 80

Vc = 490 sfm, fz = 0.030 ipt
760 46 600 48 470 47 380 46 300 42
Vc = 400 sfm, fz = 0.020 ipt
1,260 227 1,010 242 790 237 630 227 500 210
Vc = 660 sfm, fz = 0.060 ipt
950 171 750 180 590 177 470 170 380 160
Vc = 500 sfm, fz = 0.060 ipt
250 15 200 16 150 15 120 14 100 14
Vc = 130 sfm, fz = 0.020 ipt
630 15 500 16 390 16 310 15 250 14
Vc = 330 sfm, fz = 0.008 ipt
380 2 300 2 240 2 190 2 150 2
Vc = 200 sfm, fz = 0.002 ipt

Tungaloy D023
 TX S W
High-Feed Milling
Su p e r h i g h -f e e d m i l i ng cut ter w i t h l arg e d e p t h of c u t ; B ore t y p e

A.R. = +5°, R.R. = 0°

øDb
ød

b
a

ℓ
Lf
øDc1

ap
14°
øDc

Inch Max. ap øDc z øDc1 øDb Lf ød ℓ a b lb Air hole Insert

TXSW15U2.00B0.75R03 0.098 2.000 3 0.929 1.850 1.969 0.750 0.750 0.315 0.197 0.947 with SWMT15...
TXSW15U2.50B0.75R04 0.098 2.500 4 1.480 2.323 1.969 0.750 0.750 0.315 0.197 1.520 with SWMT15...
TXSW15U3.00B1.00R05 0.098 3.000 5 1.980 2.835 2.480 1.000 1.024 0.374 0.236 2.710 with SWMT15...
TXSW15U4.00B1.50R06 0.098 4.000 6 2.980 3.819 2.480 1.500 1.063 0.626 0.394 4.870 with SWMT15...
TXSW15U5.00B1.50R07 0.098 5.000 7 3.980 3.819 2.480 1.500 1.614 0.626 0.394 6.370 with SWMT15...
TXSW15U6.00B2.00R08 0.098 6.000 8 4.980 4.331 2.480 2.000 1.496 0.748 0.433 8.290 with SWMT15...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Shell locking bolt Center bolt
(Optional parts)
TXSW15U2.00B0.75R03 TS50115l H-TB2W M-1000 BT20S SR 5/16-32UNEF_3/8-24UNF -
TXSW15U2.50B0.75R04 TS50115l H-TB2W M-1000 BT20S - (SD06-A 6)
TXSW15U3.00B1.00R05 TS50115l H-TB2W M-1000 BT20S - (C0.500X1.375H)
TXSW15U4.00B1.50R06 TS50115l H-TB2W M-1000 BT20S - (SD-12-99)
TXSW15U5.00B1.50R07 TS50115l H-TB2W M-1000 BT20M - (TMBA-0.750H)
TXSW15U6.00B2.00R08 TS50115l H-TB2W M-1000 BT20M - -

INSERT
SW M T-M J
ap

ød T
A

rε
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys  : First choice
H Hard materials  : Second choice
Coated
AH3135

Max.
AH120

Designation rε ap A ød T

SWMT1506ZER-MJ 0.079 0.098 z z 0.625 0.625 0.268

z: Line up

Reference pages
Standard cutting conditions → D025

D024 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Workpiece materials Hardness Priority Grades Chip- Cutting speed Feed per tooth
ISO

High-Feed Milling
breaker Vc (sfm) fz (ipt)
- 300 HB First choice AH3135 MJ 330 - 1000 0.02 - 0.08
Low carbon steel
(1015, etc.) - 300 HB Second choice AH120 MJ 330 - 1000 0.02 - 0.08

- 300 HB First choice AH3135 MJ 330 - 660 0.02 - 0.08

Carbon steel and alloy steel
(1015, 4140, etc.) - 300 HB Second choice AH120 MJ 330 - 660 0.02 - 0.08

30 - 40 HRC First choice AH3135 MJ 330 - 660 0.02 - 0.06

Prehardened steel
(NAK80, PX5, etc.) Second choice
30 - 40 HRC AH120 MJ 330 - 660 0.02 - 0.06

Stainless steel - 200 HB First choice AH3135 MJ 330 - 500 0.012 - 0.04
(S30400, S31600, etc.)
Grey cast iron 150 -250 HB First choice AH120 MJ 330 - 1000 0.02 - 0.08
(No.250B, No.300B, etc.)
Ductile cast iron First choice
(60-40-18, 80-55-06, etc.) 150 -250 HB AH120 MJ 260 - 660 0.02 - 0.08
Titanium alloys (Ti-6AI-4V, etc.) - 40 HRC First choice AH3135 MJ 100 - 200 0.012 - 0.028

Superalloys (Inconel718, etc.) - 40 HRC First choice AH120 MJ 60 - 160 0.004 - 0.012

(H13, etc.) 40 - 50 HRC First choice AH3135 MJ 260 - 420 0.004 - 0.012
Hardened steel
(D2, etc.) 50 - 60 HRC First choice AH120 MJ 160 - 230 0.001 - 0.003

A PPLICATION R A NGE
Shoulder Small depth Drilling
milling plunging Ramping Plunging (Helical feed) Enlarging hole
ap

θ°
A

W
ae
øD1, 2

Max. depth of Max. Max. cutting Min. Max. Max. cutting

Max. ramping width in
plunging width in machining machining
cut angle plunging dia. dia. enlarging
Inch øDc ap A θ° W øD1 øD2 ae
TXSW15U2.00B0.75R03 2.000 0.098 0.028 4.6 0.591 2.787 3.771 1.433
TXSW15U2.50B0.75R04 2.500 0.098 0.028 2.9 0.591 3.819 4.803 1.949
TXSW15U3.00B1.00R05 3.000 0.098 0.028 2.1 0.591 4.819 5.803 2.449
TXSW15U4.00B1.50R06 4.000 0.098 0.028 1.4 0.591 6.819 7.803 3.449
TXSW15U5.00B1.50R07 5.000 0.098 0.028 1.0 0.591 8.819 9.803 4.449
TXSW15U6.00B2.00R08 6.000 0.098 0.028 0.8 0.591 10.819 11.803 5.449

TOOL GEOME TRY FOR PROGR A MMING

Max. ap

t2
14º

rε
R
w
t1

Max. ap (in) Actual corner radius rε (in) W (in) Programmed corner radius R (in) Uncut amount t1 (in) Overcut amount t2 (in)
0.098 0.079 0.500 0.157 0.078 -
0.098 0.079 0.500 0.177 0.074 -
0.098 0.079 0.500 0.197 0.070 0.0004
- When programming for CAM, the tool should be considered as a radius cutter. Usually, the corner radius should be set in R = 0.177".
If a larger radius is used, overcutting may occur. The above table shows the uncut (t1) and overcut (t2) amounts for the programmed corner radius.

Tungaloy D025
 TXP 05/06/08 /09
High-Feed Milling
Su p e r h i g h f e e d m i l l i ng cut ter
A.R. = +5°, R.R. = -4° ~ -6°
Lf
R

a
øDc1
øDc

øDb
ød
ap b
κ°
Inch Max. ap øDc z øDc1 øDb Lf ød ℓ a b κ° Ib Air hole Insert
TXP05250RBU 0.060 2.500 6 2.190 2.323 1.969 0.750 0.750 0.315 0.197 15 1.76 with WPMT05...
TXP05300RBU 0.060 3.000 7 2.690 2.835 2.480 1.000 1.024 0.374 0.236 20 3.31 with WPMT05...
TXP06200RBU 0.060 2.000 4 1.650 1.850 1.969 0.750 0.750 0.315 0.197 20 1.10 with WPMT06...
TXP06250RBU 0.060 2.500 5 2.150 2.323 1.969 0.750 0.750 0.315 0.197 20 1.76 with WPMT06...
TXP06300RBU 0.060 3.000 6 2.650 2.835 2.480 1.000 1.024 0.374 0.236 20 3.09 with WPMT06...
TXP08050RU 0.060 2.000 3 1.547 1.850 1.969 0.750 0.750 0.315 0.197 10 0.87 without WPMT08...
TXP08200RU-A 0.060 2.000 3 1.547 1.850 1.969 0.750 0.750 0.315 0.197 10 0.87 with WPMT08...
TXP08300RU-A 0.060 3.000 5 2.547 2.835 2.480 1.000 1.024 0.375 0.236 10 3.20 with WPMT08...
TXP08400RU-A 0.060 4.000 6 3.547 3.819 2.480 1.500 1.260 0.625 0.394 10 5.80 with WPMT08...
TXP09250RU 0.118 2.500 3 1.971 2.323 1.969 0.750 0.750 0.315 0.197 20 1.54 with WPMT09...
TXP09300RU 0.118 3.000 4 2.470 2.835 2.480 1.000 1.024 0.374 0.236 20 2.65 with WPMT09...
TXP09400RU 0.118 4.000 5 3.471 3.780 2.480 1.500 1.457 0.626 0.394 20 4.41 with WPMT09...
TXP09500RU 0.118 5.000 6 4.471 3.780 2.480 1.500 1.457 0.626 0.394 20 6.83 with WPMT09...
TXP09600RU 0.118 6.000 7 5.471 4.331 2.480 2.000 1.496 0.748 0.433 20 9.48 without WPMT09...

SPARE PARTS
Designation Clamp set Clamping screw Lubricant Wrench Wrench 1 Center bolt
(Optional parts)
TXP05... - CSPB-3.5S M-1000 IP-15D - (C0.375X1.125H)
TXP06200RBU, TXP06250RBU CSY-15 CSPB-4S M-1000 IP-15D - (C0.375X1.125H)
TXP06300RBU CSY-15 CSPB-4S M-1000 IP-15D - (C0.500X1.375H)
TXP08... CSX20 CSTB-5 M-1000 - T-20T -
TXP09250RU CSY-20 CSPB-5 M-1000 - IP-20T (C0.375X1.125H)
TXP09300RU CSY-20 CSPB-5 M-1000 - IP-20T (C0.500X1.375H)
TXP09400RU, TXP09500RU CSY-20 CSPB-5 M-1000 - IP-20T (TMBA-0.750H)
TXP09600RU CSY-20 CSPB-5 M-1000 - IP-20T -

Reference pages
Inserts → D028, Standard cutting conditions → D029 - D030

D026 www.tungaloyamerica.com
EXP 05/06/09

High-Feed Milling
Sup e r h i g h f e e d end m i l l
A.R. = +5°, R.R. = -6°

L
Lf Rs

øDc1

øDsh6
øDc
ap
κ°

Inch Max. ap øDc z øDc1 øDs L Lf ℓs κ° Air hole Insert shank

EXP05075RSU 0.060 0.750 2 0.480 0.750 4.030 2.000 2.031 15 with WPM*05H315ZPR Weldon
EXP05075RLU 0.060 0.750 2 0.480 0.750 4.030 2.000 2.031 15 with WPM*05H315ZPR Straight
EXP05075RLLU 0.060 0.750 2 0.480 0.750 7.000 4.000 3.000 15 with WPM*05H315ZPR Straight
EXP06100RSU 0.060 1.000 2 0.697 1.000 8.000 5.000 3.000 15 with WPM*06X415ZPR Weldon
EXP06100RLU 0.060 1.000 2 0.697 1.000 8.000 5.000 3.000 15 with WPM*06X415ZPR Straight
EXP06100RLLU 0.060 1.000 2 0.697 1.000 12000 7.000 5.000 15 with WPM*06X415ZPR Straight
EXP06125RSBU 0.060 1.250 3 0.929 1.250 5.281 3.000 2.281 20 with WPM*06X415ZPR Weldon
EXP06125RLBU 0.060 1.250 3 0.929 1.250 8.000 5.000 3.000 20 with WPM*06X415ZPR Straight
EXP06125RLLBU 0.060 1.250 3 0.929 1.250 12.000 7.000 5.000 20 with WPM*06X415ZPR Straight
EXP06150RSU 0.060 1.500 3 1.169 1.250 5.781 3.500 2.281 20 with WPM*06X415ZPR Weldon
EXP06150RLU 0.060 1.500 3 1.169 1.250 10.000 2.000 8.000 20 with WPM*06X415ZPR Straight
EXP06150RLLU 0.060 1.500 3 1.169 1.250 12.000 2.000 10.000 20 with WPM*06X415ZPR Straight
EXP09200RU 0.118 2.000 2 1.477 1.250 4.781 2.500 2.281 20 with WPMT090725Z*R Weldon
EXP09200RLU 0.118 2.000 2 1.477 1.250 9.750 2.000 7.750 20 with WPMT090725Z*R Straight

SPARE PARTS
Designation Clamp set Clamping screw Lubricant Wrench Wrench 1
EXP05... - CSPB-3.5S M-1000 IP-15D -
EXP06... CSY-15 CSPB-4S M-1000 IP-15D -
EXP09... CSY-20 CSPB-5 M-1000 - IP-20T

Reference pages
Inserts → D028, Standard cutting conditions → D029 - D030

Tungaloy D027
 INSERT
High-Feed Milling W P M W 05/06 W PM T 0 8 / 0 9
T T

A
rε 11˚
ød rε 11˚
ød

W P M T05/06 /08/09- M L W PM T 0 5 / 0 6 / 0 8 / 0 9 -M H
T T
A

A
11°
rε 11° rε
ød ød

W P M T05/06 /08/09- DM L
T
A

11°
rε
ød
P Steel  
M Stainless  
K Cast iron 
N Non-ferrous
S Superalloys  : First choice
H Hard materials  : Second choice
Coated

Max.
AH330
AH730
AH130
AH120

AH140

T3130

Designation rε ap A ød T

WPMW05H315ZPR 0.059 0.060 z z z 0.197 0.3130 0.138

WPMT05H315ZPR-ML 0.059 0.060 z z z 0.197 0.3130 0.138
WPMT05H315ZPR-MH 0.059 0.060 z z 0.197 0.3134 0.138
WPMT05H315ZPR-DML 0.059 0.060 z 0.197 0.3130 0.138
WPMW06X415ZPR 0.059 0.060 z z z 0.236 0.3750 0.165
WPMT06X415ZPR-ML 0.059 0.060 z z z z 0.236 0.3750 0.165
WPMT06X415ZPR-MH 0.059 0.060 z z 0.236 0.3755 0.165
WPMT06X415ZPR-DML 0.059 0.060 z 0.236 0.3750 0.165
WPMT080615ZSR 0.059 0.060 z z z z z 0.315 0.507 0.250
WPMT080615ZPR-ML 0.059 0.060 z z z z 0.315 0.507 0.250
WPMT080615ZSR-MH 0.059 0.060 z z 0.315 0.507 0.250
WPMT080615ZPR-DML 0.059 0.060 z 0.315 0.507 0.250
WPMT090725ZSR 0.098 0.118 z z z 0.354 0.591 0.276
WPMT090725ZPR-ML 0.098 0.118 z z z z 0.354 0.591 0.276
WPMT090725ZSR-MH 0.098 0.118 z z z 0.354 0.591 0.276
WPMT090725ZPR-DML 0.098 0.118 z 0.354 0.591 0.276

z: Line up

D028 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
0 5· 06 t ype

High-Feed Milling
Workpiece Insert Cutting Feed per
ø0.750" ø1.000" ø1.250" ø1.500" ø2.500" ø3.000"
ISO speed tooth
material grade (z = 2) (z = 2) (z = 2, 3) (z = 3) (z = 5, 6) (z = 6, 7)
Vc (sfm) fz (ipt)
Vc = 500 sfm, fz = 0.031 ipt Vc = 500 sfm, fz = 0.039 ipt
Carbon Steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D" ap = 0.039", ae = 0.039D"
1055, etc. 330 ~ 820
(T3130) 0.078
< 300HB When plunging in small depth: fz = 0.008"

Vc = 425 sfm, fz = 0.031 ipt Vc = 425 sfm, fz = 0.039 ipt

Alloy steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D" ap = 0.039", ae = 0.039D"
4140, etc. 330 ~ 650
(T3130) 0.078
< 300 HB When plunging in small depth: fz = 0.008"

Vc = 330 sfm, fz = 0.020 ipt Vc = 330 sfm, fz = 0.020 ipt

Prehardened steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D" ap = 0.039", ae = 0.039D"
P20, H13, etc. 260 ~ 500
(T3130) 0.039
30 ~ 40HRC When plunging in small depth: fz = 0.004 ipt

Vc = 425 sfm, fz = 0.031 ipt Vc = 425 sfm, fz = 0.039 ipt

Stainless steels AH130 0.020 ~ ap = 0.039", ae = 0.039D" ap = 0.039", ae = 0.039D"
330 ~ 650
S30400, etc. AH140 0.078
When plunging in small depth: fz = 0.008 ipt

Vc = 500 sfm, fz = 0.039 ipt Vc = 590 sfm, fz = 0.059 ipt

Cast irons 0.032 ~ ap = 0.039", ae = 0.039D" ap = 0.039", ae = 0.039D"
AH120 330 ~ 820
250, etc. 0.098
When plunging in small depth: fz = 0.008 ipt

Vc = 164 sfm, fz = 0.020 ipt, ap = 0.028", ae = 0.020D"

Titanium alloys 0.012 ~
Ti-6Al-4V, etc. AH130 98 ~ 197
0.028
When plunging in small depth: fz = 0.004 ipt

Vc = 98 sfm, fz = 0.008 ipt, ap = 0.028", ae = 0.020D"

Heat-resistant alloys 0.004 ~
Inconel 718, etc. AH120 33 ~ 131
0.012
When plunging in small depth: fz = 0.004 ipt

Hard materials Vc = 230 sfm, fz = 0.028 ipt, ap = 0.028", ae = 0.039D"

0.020 ~
D2, etc. AH730 200 ~ 330
0.078
40 ~ 50HRC When plunging in small depth: fz = 0.004 ipt

0 8 t ype

Workpiece Insert Cutting Feed per ø2.000" ø3.000" ø4.000"

ISO speed tooth
material grade Vc (sfm) fz (ipt) (z = 3) (z = 4) (z = 6)
Vc = 650 sfm, fz = 0.059 ipt
Carbon Steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D"
1055, etc. 330 ~ 820
(T3130) 0.078
< 300HB When plunging in small depth: fz = 0.008 ipt
Vc = 500 sfm, fz = 0.059 ipt
Alloy steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D"
4140, etc. 330 ~ 650
(T3130) 0.078
< 300 HB When plunging in small depth: fz = 0.008 ipt
Vc = 120 sfm, fz = 0.031 ipt
Prehardened steels
AH120 0.020 ~ ap = 0.039", ae = 0.039D"
P20, H13, etc. 260 ~ 500
(T3130) 0.039
30 ~ 40HRC When plunging in small depth: fz = 0.004 ipt
Vc = 500 sfm, fz = 0.059 ipt
Stainless steels AH130 0.020 ~ ap = 0.039", ae = 0.039D"
330 ~ 650
S30400, etc. AH140 0.078
When plunging in small depth: fz = 0.008 ipt
Vc = 650 sfm, fz = 0.078 ipt
Cast irons 0.032 ~ ap = 0.039", ae = 0.039D"
AH120 500 ~ 820
250, etc. 0.098
When plunging in small depth: fz = 0.008 ipt

Vc = 164 sfm, fz = 0.020 ipt, ap = 0.028", ae = 0.020D"

Titanium alloys 0.012 ~
Ti-6Al-4V, etc. AH130 98 ~ 197
0.028
When plunging in small depth: fz = 0.004 ipt

Vc = 98 sfm, fz = 0.008 ipt, ap = 0.028", ae = 0.020D"

Heat-resistant alloys 0.004 ~
Inconel 718, etc. AH120 33 ~ 131
0.012
When plunging in small depth: fz = 0.004 ipt
Vc = 230 sfm, fz = 0.078 ipt
Hard materials
0.020 ~ ap = 0.087", ae = 0.039D"
D2, etc. AH730 170 ~ 260
0.039
40 ~ 50HRC When plunging in small depth: fz = 0.004 ipt

Note: • The above values of cutting speed show the standard speed when overhang length of tool is below 3D. The cutting speed and the feed rate should be
set at the lower limit values when overhang length of tool exceeds 3D.
• Thick and heavy chips are discharged by these TAC mills. Use internal air supply or air-blowing in order to prevent tool failure.

Tungaloy D029
 STA NDA RD CUT TING CONDITIONS
09 type
High-Feed Milling

Workpiece Insert Cutting Feed per ø4.000

ISO speed tooth ø2.000 ø2.500 ø3.000 ø5.000 ø6.000
material grade Vc (sfm) fz (ipt) (z = 2) (z = 3) (z = 4) (z = 5) (z = 6) (z = 7)
Carbon Steels Vc = 650 sfm, fz = 0.059 ipt, ap = 0.079", ae = 0.039D"
AH120 0.020 ~
1055, etc. 330 ~ 820
(T3130) 0.078
< 300HB When plunging in small depth: fz = 0.008 ipt

Alloy steels Vc = 500 sfm, fz = 0.059 ipt, ap = 0.079", ae = 0.039D"

AH120 0.020 ~
4140, etc. 330 ~ 650
(T3130) 0.078
< 300 HB When plunging in small depth: fz = 0.008 ipt

Prehardened steels Vc = 3.94, fz = 0.031 ipt, ap = 0.079", ae = 0.039D"

AH120 0.020 ~
P20, H13, etc. 260 ~ 500
(T3130) 0.039
30 ~ 40HRC When plunging in small depth: fz = 0.004 ipt

Vc = 500 sfm, fz = 0.059 ipt, ap = 0.079", ae = 0.039D"

Stainless steels AH130 0.020 ~
330 ~ 650
S30400, etc. AH140 0.078
When plunging in small depth: fz = 0.008 ipt

Vc = 650 sfm, fz = 0.078 ipt, ap = 0.079", ae = 0.039D"

Cast irons 0.032 ~
AH120 500 ~ 820
250, etc. 0.098
When plunging in small depth: fz = 0.008 ipt

Vc = 164 sfm, fz = 0.020 ipt, ap = 0.059", ae = 0.020D"

Titanium alloys 0.012 ~
Ti-6Al-4V, etc. AH130 98 ~ 197
0.028
When plunging in small depth: fz = 0.039 ipt

Vc = 98 sfm, fz = 0.008 ipt, ap = 0.039", ae = 0.020D"

Heat-resistant alloys 0.004 ~
Inconel 718, etc. AH120 33 ~ 131
0.012
When plunging in small depth: fz = 0.039 ipt

Hard materials Vc = 230 sfm, fz = 0.028 ipt, ap = 0.027", ae = 0.039D"

0.020 ~
D2, etc. AH730 200 ~ 330
0.039
40 ~ 50HRC When plunging in small depth: fz = 0.004 ipt

Notes : The cutting speed and feed should be set to 70 to 80 % of the value shown in the above table when overhang length of tool exceeds 3D.

D030 www.tungaloyamerica.com
 A PPLICATION R A NGE
Shoulder milling Grooving Plunging Enlarging hole diameter

High-Feed Milling
Enlarging

Ramping Traversing
θ° A
Hp

ø+ He

Max. depth of Max. Max. Min. Max. Max. cutting

ramping plunging machining machining width in
cut angle depth hole dia. hole dia. enlarging hole
Inch øDc ap θ° A øD øD ae
TXP05250RBU 2.500 0.060 2° 30' 0.020 3.860 4.840 2.240
TXP05300RBU 3.000 0.060 1° 30' 0.020 5.200 6.180 2.910
TXP06250RBU 2.500 0.060 2° 0.040 3.860 4.840 2.240
TXP06200RBU 2.000 0.060 1° 30' 0.040 3.270 3.820 1.770
TXP06300RBU 3.000 0.060 1° 30' 0.040 5.200 6.180 2.910
TXP08050RU 2.000 0.060 4° 0.040 2.830 3.820 1.730
TXP08300RU-A 3.000 0.060 1° 30' 0.040 5.200 6.180 2.910
TXP08400RU-A 4.000 0.060 1° 0.040 6.770 7.760 3.700
TXP09250RU 2.500 0.118 2° 0.060 3.860 4.840 2.200
TXP09300RU 3.000 0.118 1° 30' 0.060 5.200 6.180 2.870
TXP09400RU 4.000 0.118 1° 0.060 6.770 7.760 3.660
TXP09500RU 5.000 0.118 0° 45' 0.060 8.740 9.720 4.650
TXP09600RU 6.000 0.118 0° 30' 0.060 11.500 12.480 6.020
EXP05075... 0.750 0.060 3° 0.020 1.181 1.457 0.630
EXP06100... 1.000 0.060 5° 0.039 1.299 1.850 0.787
EXP06125... 1.250 0.060 3° 30' 0.039 1.850 2.402 1.063
EXP06150... 1.500 0.060 2° 0.039 2.480 2.874 1.299
EXP09200... 2.000 0.118 1.5° 0.031 2.992 3.819 1.693

TO OL GEOME TRY FOR PROGR A MMING

When programming for CAD/CAM, the tool should be assumed to be a radius cutter shown in the table below. In this case, the
amount left as uncut (t) is shown below.

Max. depth of Corner Cutting edge

Hp(Max depth of cut)

Corner R when
cut of insert angle programming
TXP ap rε κ° W t
05 0.060 0.059 20 0.150 0.020 R.078

06 0.060 0.059 20 0.169 0.028 R.078

08 0.060 0.059 20 0.224 0.028 R.078

09 0.118 0.098 20 0.268 0.055 R.118

Corner rε
κ° Amount left 09 0.118 0.098 20 0.268 0.047 R.157
as uncut : [
>
Corner R when programming

Tungaloy D031
 MillLin e - Shoulde r Milling
Inch Metric
D034
Economical and versatile shoulder mills with double-sided triangular inserts
ø1.250" - ø5.000"
‡ max. ap 0.433"

D038
High-precision shoulder mills with single-sided triangular inserts
ø0.472" - ø6.000"
‡ max. ap 0.591" / 3.268"

D 0 47
Square shoulder milling cutters for roughing to produce shredded chips
ø2.000" - ø4.000"
‡ max. ap 0.630" / 2.992"

D050
Mini square shoulder milling cutters for high productivity

‡ ø0.313" - ø0.625"
max. ap 0.236"

D054
Excellent surface finish and wall accuracy in shoulder milling

‡ ø0.472" - ø6.299"
max. ap 0.657"

D069
Ideal tool for milling small parts on small machines
ø0.500" - ø2.000"
‡ max. ap 0.157"

D 072
Single-sided inserts with low cutting force for shoulder milling

‡ ø1.260"- ø6.000"
max. ap 0.394"

D 076
Shoulder milling cutters for general purpose with 4-cornered double-sided inserts
ø1.000" - ø6.000"
‡ max. ap 0.630"

D 079
Shoulder milling cutters for heavy machining duty with 4-cornered tangentially mounted inserts

‡ ø1.250" - ø5.000"
max. ap 0.594"

D 0 81
Highly polished and positive routing milling cutters for aluminum and non-ferrous metals
ø1.000" - ø5.000"
‡ max. ap 0.630"

Other Shoulder Milling Tools D084

EPH, TPS, EPS, EVH, EXH

D032 www.tungaloyamerica.com
D o Fo rc e -Tr i

Tungaloy D033
 TPTN 12
S q u a re S h o u l d e r m i l l i n g c u t te r s w i t h d o u b l e - s i d e d t r i a n g u l a r i n s e r t

A.R. = +4.2°~ +4.7°, R.R. = -15.4°~ -11.2°

øDb
ød R
a

b
R
R R

Lf
ap
Shoulder Milling

øDc 90°

Inch Max. ap øDc z øDb Lf ød ℓ a b lb Air hole Insert

TPTN12U2.00B0.75R05 0.433 2.000 5 1.850 1.575 0.750 0.750 0.315 0.197 0.890 with TN*U12...
TPTN12U2.50B0.75R06 0.433 2.500 6 1.850 1.575 0.750 0.750 0.315 0.197 1.330 with TN*U12...
TPTN12U3.00B1.00R08 0.433 3.000 8 2.835 1.969 1.000 1.024 0.374 0.236 2.440 with TN*U12...
TPTN12U4.00B1.50R10 0.433 4.000 10 3.150 1.969 1.500 1.181 0.626 0.394 3.110 with TN*U12...
TPTN12U5.00B1.50R12 0.433 5.000 12 3.150 2.480 1.500 1.181 0.626 0.394 5.330 with TN*U12...

SPARE PARTS
Designation Clamping screw Grip Torx bit Lubricant Center bolt Center bolt 1
(Optional parts) (Optional parts)
TPTN12U2.00, 2.50... CSPB-3.5 H-TB2W BLDIP15/S7 M-1000 - (C0.375X1.125H)
TPTN12U3.00B1.00R08 CSPB-3.5 H-TB2W BLDIP15/S7 M-1000 - (C0.500X1.375H)
TPTN12U4.00, 5.00... CSPB-3.5 H-TB2W BLDIP15/S7 M-1000 (TMBA-0.750S.375) -

EP TN 12
S q u a re S h o u l d e r m i l l i n g e n d m i l l s w i t h d o u b l e - s i d e d t r i a n g u l a r i n s e r t

A.R. = +4.2°~ +4.7°, R.R. = -15.4°~ -11.2°

R
øDs
øDc

R R

ap
90° Lf ℓs
L

Inch Max. ap øDc z øDs ℓs Lf L lb Air hole Insert

EPTN12U1.25C1.25R03N 0.433 1.250 3 1.250 3.000 1.500 4.500 1.560 without TN*U12...
EPTN12U1.50C1.25R04N 0.433 1.500 4 1.250 3.000 1.500 4.500 1.780 without TN*U12...

SPARE PARTS
Designation Clamping screw Grip Torx bit Lubricant
EPTN12... CSPB-3.5 H-TB2W BLDIP15/S7 M-1000

Reference pages
Inserts → D035, Standard cutting conditions → D036

D034 www.tungaloyamerica.com
 INSERT
T N G U -M J / TN M U- M J T N G U -N M J / T N M U -N M J

T T

ap
ap
A

A
ød bs rε ød bs rε

T N M U -R -M J

Shoulder Milling
ap
A

ød rε
P Steel  
M Stainless  
K Cast iron  
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated
AH3135

Max.
AH120

T3225

Designation A T bs
T1215

rε ap ød

TNGU120708PER-MJ 0.031 0.433 z z 0.472 0.375 0.277 0.046

TNGU120708PER-NMJ 0.031 0.433 z z 0.472 0.375 0.277 0.046
TNMU1207R16PER-MJ 0.063 0.433 z z 0.472 0.375 0.277 -
TNMU120708PER-MJ 0.031 0.433 z z z z 0.472 0.375 0.277 0.046
TNMU120708PER-NMJ 0.031 0.433 z z 0.472 0.375 0.277 0.046

z: Line up

Tungaloy D035
 STA NDA RD CUT TING CONDITIONS
Chip- Cutting speed Feed per tooth
ISO Workpiece materials Hardness Priority Grades
breaker Vc (sfm) fz (ipt)

- 300 HB First choice AH3135 MJ 328 - 820 0.003 - 0.012

Low carbon steels Priority on wear

- 300 HB T3225 MJ 328 - 984 0.003 - 0.012
(1018, 1026, etc.) resistance

- 300 HB For low cutting force AH3135 NMJ 328 - 820 0.003 - 0.006

- 300 HB First choice AH3135 MJ 328 - 755 0.003 - 0.012

Carbon steels, Alloy steels Priority on wear

Shoulder Milling

- 300 HB T3225 MJ 328 - 919 0.003 - 0.012

(1055, 4140, etc.) resistance

- 300 HB For low cutting force AH3135 NMJ 328 - 919 0.003 - 0.006

30 - 40 HRC First choice AH3135 MJ 328 - 591 0.003 - 0.010

Prehardened steel Priority on wear

30 - 40 HRC T3225 MJ 328 - 656 0.003 - 0.010
(H-13, P-20, etc.) resistance

30 - 40 HRC For low cutting force AH3135 NMJ 328 - 591 0.003 - 0.006

- First choice AH3135 MJ 295 - 656 0.003 - 0.010

Stainless steels Priority on wear

- T3225 MJ 295 - 820 0.003 - 0.010
(304, 316, etc) resistance

- For low cutting force AH3135 NMJ 295 - 656 0.003 - 0.006

150 - 250 HB First choice AH120 MJ 459 - 820 0.003 - 0.012

Grey cast irons Priority on wear

150 - 250 HB T1215 MJ 459 - 984 0.003 - 0.012
(Class 25, Class 30, etc.) resistance

150 - 250 HB For low cutting force AH120 NMJ 459 - 820 0.003 - 0.006

150 - 250 HB First choice AH120 MJ 361 - 656 0.003 - 0.010

Ductile cast irons Priority on wear

150 - 250 HB T1215 MJ 361 - 820 0.003 - 0.010
(60-40-18, 80-55-06, etc.) resistance

150 - 250 HB For low cutting force AH120 NMJ 361 - 656 0.003 - 0.006

- First choice AH120 MJ 70 - 200 0.003 - 0.008

Titanium alloys
(Ti-6AI-4V, etc.)
- For low cutting force AH120 NMJ 70 - 200 0.003 - 0.006

- First choice AH120 MJ 70 - 130 0.003 - 0.007

Heat-resistant alloys
(Inconel718, etc.)
- For low cutting force AH120 NMJ 70 - 130 0.003 - 0.006

When you use the NMJ chipbreaker, please set up the feed less than 0.006 ipt.

D036 www.tungaloyamerica.com
MEMO

Shoulder Milling

Tungaloy D037
 TPA 06
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g c u t te r s w i t h t r i a n g u l a r i n s e r t s

A.R. = +8.5°~ +11.5°, R.R. = -5.5°~ -12.5°

øDb
ød

b
R
a

R
R R

Lf
ap
Shoulder Milling

øDc 90°

Inch Max. ap øDc z øDb ød ℓ Lf b a lb Air hole Insert

TPA06R200U0075A08 0.236 2.000 8 1.693 0.750 0.750 1.575 0.197 0.315 0.310 with TOMT06...

SPARE PARTS
Designation Clamping screw Lubricant Wrench Center bolt
(Optional parts)
TPA06R200U0075A08 CSTB-2.5 M-1000 T-8D (C0.375X1.125H)

EPA06
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g e n d m i l l s w i t h t r i a n g u l a r i n s e r t s
A.R. = +8.5°~ +11.5°, R.R. = -5.5°~ -12.5°

øDs
øDc

R R

ap
90° Lf Rs
L
Inch Max. ap øDc z øDs ℓs Lf L lb Air hole Insert
EPA06R050U0050-01N 0.236 0.500 1 0.500 2.250 0.750 3.000 0.200 without TOMT06...
EPA06R063U0063-02N 0.236 0.625 2 0.625 2.563 0.937 3.500 0.260 without TOMT06...
EPA06R075U0075-03N 0.236 0.750 3 0.750 2.858 1.142 4.000 0.440 with TOMT06...
EPA06R100U0100W04N 0.236 1.000 4 1.000 2.280 1.500 3.780 0.290 without TOMT06...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
øDc ≤ 0.625" CSTB-2.5S M-1000 T-8D
EPA06...
øDc ≥ 0.750" CSTB-2.5 M-1000 T-8D

Reference pages
Inserts → D044, Standard cutting conditions → D045

D038 www.tungaloyamerica.com
HPA 06-M
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g e n d m i l l s w i t h t r i a n g u l a r i n s e r t s

A.R. = +8.5°~ +11.5°, R.R. = -12.5°~ -5.5°

L6
Lf R
C Ts T
A R R

øDc

øD3
ap A A-A cross section

Shoulder Milling
90°

Metric Max. ap øDc z L6 Lf C T øD3 Ts Ib Air hole Insert

HPA06R016MM08-02 6 16 2 42 25 8 10 13 M8 0.030 with TOMT06...
HPA06R020MM10-03 6 20 3 49 30 10 15 18 M10 0.060 with TOMT06...
HPA06R025MM12-04 6 25 4 57 35 10 17 21 M12 0.100 with TOMT06...
HPA06R032MM16-05 6 32 5 63 40 12 22 29 M16 0.200 with TOMT06...
See page D147 for TungFlex modular shank.

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HPA06R016MM08-02 CSTB-2.5S M-1000 T-8D
HPA06R020 - 032MM... CSTB-2.5 M-1000 T-8D

T PA10
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g c u t te r s w i t h t r i a n g u l a r i n s e r t s

A.R. = +9.5°~ +11°, R.R. = -4.5°~ -0.5°

øDb
ød
b

R
a
R

R R
Lf
ap

øDc 90°
Inch Max. ap øDc z øDb ød ℓ Lf b a Ib Air hole Insert
TPA10R200U0075A04 0.394 2.000 4 1.693 0.750 0.750 1.575 0.197 0.315 0.440 with TOMT10...
TPA10R250U0075A06 0.394 2.500 6 1.693 0.750 0.750 1.575 0.197 0.315 0.680 with TOMT10...
TPA10R300U0100A07 0.394 3.000 7 2.283 1.000 1.024 1.969 0.236 0.374 1.120 with TOMT10...
TPA10R400U0150A08 0.394 4.000 8 3.150 1.500 1.413 2.480 0.394 0.626 2.290 with TOMT10...

SPARE PARTS
Designation Clamping screw Grip Torx bit Lubricant Center bolt
(Optional parts)
TPA10R200U - 300U... SR14-562/S SW6-SD BLDT10/S7 M-1000 (C0.375X1.125H)
TPA10R400U0150A08 SR14-562/S SW6-SD BLDT10/S7 M-1000 -

Reference pages
Inserts → D044, Standard cutting conditions → D045

Tungaloy D039
 EPA10
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g e n d m i l l s w i t h t r i a n g u l a r i n s e r t s

A.R. = +9.5°~ +11°, R.R. = -4.5°~ -0.5°

øDs
øDc
R R

ap
90° Lf Rs
L
Shoulder Milling

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert

EPA10R100U0075W02N 0.394 1.000 2 0.750 2.362 1.378 3.740 0.44 without TOMT10...
EPA10R100U0100W02L 0.394 1.000 2 1.000 5.748 2.752 8.500 1.68 with TOMT10...
EPA10R100U0100W02N 0.394 1.000 2 1.000 2.362 1.378 3.740 0.71 without TOMT10...
EPA10R125U0125W02L 0.394 1.250 2 1.250 7.000 3.000 10.000 3.15 with TOMT10...
EPA10R125U0125W03ML 0.394 1.250 3 1.250 4.250 2.250 6.500 2.07 with TOMT10...
EPA10R125U0125W03N 0.394 1.250 3 1.250 2.362 1.378 3.740 1.12 without TOMT10...
EPA10R150U0125W02L 0.394 1.500 2 1.250 8.000 2.000 10.000 3.33 with TOMT10...
EPA10R150U0125W03ML 0.394 1.500 3 1.250 4.250 2.250 6.500 2.43 with TOMT10...
EPA10R150U0125W04N 0.394 1.500 4 1.250 3.157 1.969 5.126 1.68 without TOMT10...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit
EPA10... SR14-562/S SW6-SD M-1000 BLDT10/S7

H PA 10-M
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g e n d m i l l s w i t h t r i a n g u l a r i n s e r t s

A.R. = +9.5°~ +11°, R.R. = -4.5°~ -0.5°

L6
Lf R
C A Ts T
R R
øD3
øDc

90° ap A A-A cross section

Metric Max. ap øDc z L6 Lf C T øD3 Ts Ib Air hole Insert

HPA10R025MM12-02 10 25 2 57 35 10 17 21 M8 0.08 with TOMT10...
HPA10R032MM16-03 10 32 3 63 40 12 22 29 M10 0.18 with TOMT10...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit
HPA10... SR14-562/S SW6-SD M-1000 BLDT10/S7

Reference pages
Inserts → D044, Standard cutting conditions → D045

D040 www.tungaloyamerica.com
T LA10
E x te n d e d F l u te s q u a re s h o u l d e r m i l l s f o r ro u g h i n g w i t h t r i a n g u l a r i n s e r t s

A.R. = +9.5°~ +11°, R.R. = -4.5°~ -0.5°

Lf
R b R

R R

øDb
øDc

ød
a
Max.ap

Shoulder Milling
Inch Max. ap øDc Z eff z øDb ød ℓ Lf b a Ib Air hole Insert
TLA10R200L213U0075A04 2.126 2.000 4 24 1.875 0.750 0.750 3.250 0.197 0.315 1.760 with TOMT10...
TLA10R250L213U0100A04 2.126 2.500 4 24 2.375 1.000 1.024 3.250 0.236 0.374 2.960 with TOMT10...

SPARE PARTS
Designation Clamping screw Lubricant Wrench Center bolt
TLA10R200L213U0075A04 SR14-562 M-1000 T-10D SD06-102
TLA10R250L213U0100A04 SR14-562 M-1000 T-10D SD-08-C8

T PA15
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g c u t te r s w i t h t r i a n g u l a r i n s e r t s

A.R. = +12°~ +13.5°, R.R. = -6°~ -3.5°

øDb
ød
b
R
a
R

R R
Lf
ap

øDc 90°

Inch Max. ap øDc z øDb ød ℓ Lf b a Ib Air hole Insert

TPA15R200U0075A04 0.590 2.000 4 1.625 0.750 0.750 1.570 0.197 0.315 0.600 with TOMT15...
TPA15R250U0075A05 0.590 2.500 5 2.125 0.750 0.750 1.570 0.197 0.315 0.900 with TOMT15...
TPA15R300U0100A06 0.590 3.000 6 2.250 1.000 1.024 1.750 0.236 0.374 1.900 with TOMT15...
TPA15R400U0150A07N 0.590 4.000 7 3.000 1.500 1.181 2.000 0.394 0.626 1.270 without TOMT15...
TPA15R500U0150A08N 0.590 5.000 8 4.000 1.500 1.175 2.000 0.394 0.626 2.800 without TOMT15...
TPA15R600U0200A10N 0.590 6.000 10 4.750 2.000 1.220 2.000 0.433 0.748 10.520 without TOMT15...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Center bolt
(Optional parts)
TPA15R200U0075A04 TS45120I H-TB2W M-1000 BT20S (TCS9.525-35-I)
TPA15R250U0075A05 TS45120I H-TB2W M-1000 BT20S (C0.375X1.125H)
TPA15R300U0100A06 TS45120I H-TB2W M-1000 BT20S (C0.500X1.375H)
TPA15R400U0150A07N TS45120I H-TB2W M-1000 BT20S -
TPA15R500U0150A08N TS45120I H-TB2W M-1000 BT20M -
TPA15R600U0200A10N TS45120I H-TB2W M-1000 BT20M -

Reference pages
Inserts → D044, Standard cutting conditions → D045

Tungaloy D041
 EPA15
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g e n d m i l l s w i t h t r i a n g u l a r i n s e r t s

A.R. = +12°~ +13.5°, R.R. = -6°~ -3.5°

øDs
øDc
R R

ap
90° Lf Rs
L
Shoulder Milling

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert

EPA15R150U0125W02L  0.590 1.500 2 1.25 2.25 4.25 6.5 2.07 with TOMT15…
EPA15R150U0125W03N  0.590 1.500 3 1.25 2.25 2.25 4.5 1.48 without TOMT15…
EPA15R200U0125W04N  0.590 2.000 4 1.25 2.25 2.25 4.5 1.74 without TOMT15…

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit
EPA15... TS45120I H-TB2W M-1000 BT20S

TLA 15-M
E x te n d e d F l u te s q u a re s h o u l d e r m i l l s f o r ro u g h i n g w i t h t r i a n g u l a r i n s e r t s

A.R. = +12°~ +13.5°, R.R. = -6°~ -3.5°

Lf
R b R

R R
øDc

øDb
ød
a

Max.ap
Inch Max. ap øDc Z eff z øDb ød ℓ Lf b a lb Air hole Insert
TLA15R300L275U0125A04M 2.756 3.000 4 20 2.937 1.250 1.260 3.940 0.315 0.500 4.560 with TOMT15...
TLA15R400L326U0150A05M 3.268 4.000 5 20 3.875 1.500 1.260 4.375 0.394 0.626 10.00 with TOMT15...

SPARE PARTS
Designation Clamping screw Grip Torx bit Lubricant Center bolt
TLA15R300L275U0125A04M TS45120I H-TB2W BT20S M-1000 SD10-54
TLA15R400L326U0150A05M TS45120I H-TB2W BT20S M-1000 SD12-B9

Reference pages
Inserts → D044, Standard cutting conditions → D045

D042 www.tungaloyamerica.com
T LA 15-S
S u b u n i t to m o u n t o n T LA 1 5 - M t y p e f o r l o nge r M a x . a p re a c h

A.R. = +12°~ +13.5°, R.R. = -6°~ -3.5°

L
Lf R

R R

øDb
øDc

ød
Max.ap

Shoulder Milling
Inch Max. ap øDc Z eff z øDb ød L Lf Ib Air hole Insert
TLA15R300L110A04S 1.102 3.000 4 8 2.898 1.024 1.703 1.102 1.240 with TOMT15…
TLA15R400L110A05S 1.102 4.000 5 10 3.882 1.299 1.814 1.102 2.440 with TOMT15…

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit
TLA15... TS45120I H-TB2W M-1000 BT20S

CENTER BOLT
*Optional parts
No.of sub-units Unit 1 Unit 2
TLA15R300.. SD10-04 SD10-B3
TLA15R400.. SD12-C1 SD12-B8

Reference pages
Inserts → D044, Standard cutting conditions → D045

Tungaloy D043
 INSERT
TO M T- M J TO M T-N M J
T T
A A

rε
rε
bs
ød ød bs

TO GT- A J
Shoulder Milling

T
A

rε
bs
ød

P Steel 
M Stainless 
K Cast iron  
N Non-ferrous 
S Superalloys  : First choice
H Hard materials : Second choice
Coated Un-
coated
AH3135

Max.
KS05F
AH120

Designation A T bs
T1215

rε ap ød

TOMT060302PDER-MJ 0.008 0.236 z z 0.244 0.220 0.126 0.055

TOMT060304PDER-MJ 0.016 0.236 z z 0.244 0.220 0.126 0.047
TOMT060308PDER-MJ 0.031 0.236 z z z 0.244 0.220 0.126 0.031
TOMT100404PDER-MJ 0.016 0.394 z z 0.413 0.339 0.185 0.059
TOMT100408PDER-MJ 0.031 0.394 z z z 0.413 0.339 0.185 0.043
TOMT100416PDER-MJ 0.063 0.394 z z 0.413 0.339 0.185 0.008
TOMT150604PDER-MJ 0.016 0.590 z z 0.618 0.500 0.236 0.087
TOMT150608PDER-MJ 0.031 0.590 z z z 0.618 0.500 0.236 0.075
TOMT150616PDER-MJ 0.063 0.590 z z 0.618 0.500 0.236 0.043
TOMT150620PDER-MJ 0.079 0.590 z z 0.618 0.500 0.236 0.028
TOMT150608PDER-NMJ 0.031 0.590 z z 0.618 0.500 0.236 0.075
TOGT100404PDFR-AJ 0.016 0.394 z 0.413 0.339 0.185 0.059
TOGT100408PDFR-AJ 0.031 0.394 z 0.413 0.339 0.185 0.043
TOGT150604PDFR-AJ 0.016 0.590 z 0.618 0.500 0.236 0.087
TOGT150608PDFR-AJ 0.031 0.590 z 0.618 0.500 0.236 0.075

z: Line up

Caution for using NMJ chipbreaker

Insert with NMJ chipbreaker has a number marked on Example of a cutter body
each corner. with 4 pockets
DO NOT place the corners with the same number in
adjacent flute as the cutter may be damaged.
For example, if you place the corner #1 in one flute, be sure to
use #2 or #3 (and avoid #1) in the next one.
Item: TOMT150608PDER-NMJ

D044 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
T PA/EPA
Cutting speed: Vc (sfm) Feed per tooth: fz (ipt)
ISO Workpiece materials Hardness Grades
T/EPA06 T/EPA10 T/EPA15 T/EPA06 T/EPA10 T/EPA15
Low carbon steels 0.002 - 0.003 - 0.003 -
- 200 AH3135 330 - 720 330 - 820 330 - 820
(1015, etc). 0.006 0.008 0.01

High carbon steels 0.002 - 0.003 - 0.003 -

200 - 300 AH3135 330 - 560 330 - 660 330 - 750
(1045, etc.) 0.005 0.006 0.008

Alloyed steels 0.002 - 0.003 - 0.003 -

200 - 300 AH3135 330 - 560 330 - 660 330 - 750
(4140, etc.) 0.005 0.006 0.008

Shoulder Milling
Tool steels 0.002 - 0.003 - 0.003 -
30 - 40 HRC AH3135 330 - 390 330 - 500 330 - 600
(H13, etc.) 0.005 0.006 0.008

Stainless steels 0.002 - 0.003 - 0.003 -

- AH3135 260 - 490 260 - 660 330 - 660
(304, etc.) 0.006 0.006 0.008

Gray cast irons 0.002 - 0.005 - 0.003 -

150 - 250 AH120 330 - 660 330 - 820 330 - 820
(No.250B, etc.) 0.006 0.01 0.01

Ductile cast irons 0.002 - 0.005 - 0.003 -

150 - 250 AH120 260 - 490 260 - 660 260 - 660
(65-45-12, etc.) 0.006 0.01 0.01

Aluminum alloy 0.003 -

- KS05F - 980 - 3280 - - -
(Si < 13%) 0.009

Aluminum alloy 0.003 -

- KS05F - 330 - 660 - - -
(Si ≥ 13%) 0.009

Titanium alloy 0.002 - 0.003 - 0.003 -

- AH120 65 - 165 60 - 200 60 - 200
(Ti-6Al-4V, etc.) 0.004 0.006 0.007

Heat-resistance alloy 0.001 - 0.003 - 0.003 -

- AH120 65 - 115 60 - 130 60 - 130
(Inconel 718, etc.) 0.003 0.005 0.006

· To remove excessive chip accumulation use an air blast. · When the cutting width, depth, or overhang length is large, set Vc and
· When cutting an interrupted surface or a casted skin, the feed per tooth (fz) fz to the lower recommended values and check the machine power and
should be reduced to the lower recommended value shown in the above vibration.
table. · When you use the NMJ chipbreaker, please set up the feed less than 0.006
· Cutting conditions are limited by machine power, workpiece rigidity, and ipt.
spindle output.

T L A ( R oughi ng t y p e)
Cutting speed: Vc (sfm) Feed per tooth: fz (ipt)
ISO Workpiece material Hardness Grade
TLA10 TLA15 TLA10 TLA15
Low carbon steel - 200 HB AH3135 330 - 820 330 - 820 0.003 - 0.007 0.003 - 0.009
1015, etc.

High carbon steel

200 - 300 HB AH3135 330 - 660 330 - 890 0.003 - 0.006 0.003 - 0.007
1045, etc.

Alloy steel
200 - 300 HB AH3135 330 - 490 330 - 590 0.003 - 0.006 0.003 - 0.007
4140, etc.

Stainless steel
- AH3135 260 - 660 300 - 660 0.003 - 0.006 0.003 - 0.007
304, etc.

Grey cast iron AH120 330 - 820 460 - 820

150 - 250 HB 0.004 - 0.007 0.003 - 0.009
No.250B, etc. T1215 490 - 820 460 - 820

Ductile cast iron AH120 260 - 660 360 - 660

150 - 250 HB 0.004 - 0.007 0.003 - 0.009
65-45-12, etc. T1215 490 - 820 460 - 820

Aluminum alloy
- KS05F 980 - 3280 - 0.003 - 0.009 -
(Si < 13%)

Aluminum alloy
- KS05F 330 - 660 - 0.003 - 0.009 -
(Si ≥ 13%)

Titanium alloys
- AH120 66 - 197 66 - 197 0.003 - 0.006 0.002 - 0.006
Ti-6Al-4V, etc.

Heat-resistant alloys
- AH120 66 - 130 72 - 130 0.002 - 0.005 0.002 - 0.005
Inconel 718, etc.

Note: When you use the NMJ chipbreaker, please set up the feed less than 0.006".

Tungaloy D045
 A PPLICATION R A NGE

A
Ý
øD1, 2 øD 3 ae
Shoulder Milling

ap

ap

Max. Max. cutting

Max. depth Max. Min. machining width in
ramping Max. machining (in)
of cut (in) angle plunging (in) (in) enlarging (in)

Inch øDc ap θ A øD1 øD2 øD3 ae

EPA06R050U… 0.500 0.236 5° 0.024 0.748 0.984 0.882 0.480

EPA06R063U… 0.625 0.236 4° 0.024 0.984 1.234 1.132 0.605

EPA06R075U… 0.750 0.236 3° 0.024 1.240 1.484 1.382 0.730

EPA06R100U… 1.000 0.236 2° 0.024 1.752 1.984 1.882 0.980

TPA06R200U… 2.000 0.236 0.7° 0.024 3.740 3.984 3.882 1.980

EPA10R100U… 1.000 0.394 2° 0.024 1.689 1.984 1.882 0.980

EPA10R125U… 1.250 0.394 2° 0.024 2.189 2.484 2.382 1.230

EPA10R150U… 1.500 0.394 1.4° 0.024 2.689 2.984 2.882 1.480

TPA10R200U… 2.000 0.394 0.8° 0.024 3.689 3.984 3.882 1.980

TPA10R250U… 2.500 0.394 0.7° 0.024 4.689 4.984 4.882 2.480

TPA10R300U… 3.000 0.394 0.6° 0.024 5.689 5.984 5.882 2.980

TPA10R400U… 4.000 0.394 0.5° 0.024 7.689 7.984 7.882 3.980

EPA15R150U… 1.500 0.590 2.3° 0.031 2.547 2.969 2.823 1.461

E/TPA15R200U… 2.000 0.590 1.7° 0.031 3.547 3.969 3.823 1.961

TPA15R250U… 2.500 0.590 1.4° 0.031 4.547 4.969 4.823 2.461

TPA15R300U… 3.000 0.590 1° 0.031 5.547 5.969 5.823 2.961

TPA15R400U… 4.000 0.590 0.8° 0.031 7.547 7.969 7.823 3.961

TPA15R500U… 5.000 0.590 0.6° 0.031 9.547 9.969 9.823 4.961

TPA15R600U… 6.000 0.590 0.5° 0.031 11.547 11.969 11.823 5.961

*Flat bottom hole

Notes: Corner rε for dimensions of øD3: rε = 0.016" for T/EPA06 / 10 and rε = 0.031" for T/EPA15.

D046 www.tungaloyamerica.com
T P TC 16
S q u a re s h o u l d e r m i l l i n g c u t te r s w i t h s h re d i n s e r t

A.R. = +5.5°~ +6.5°, R.R. = -11.5°~ -11.3°

øDb
ød
a

R
b

Lf
ap

Shoulder Milling
øDc 90°

Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Insert

TPTC16U2.00B0.75R04 0.630 2.000 4 1.625 1.570 0.750 0.750 0.315 0.197 0.710 TC*T16...
TPTC16U2.50B0.75R05 0.630 2.500 5 2.125 1.570 0.750 0.750 0.315 0.197 1.260 TC*T16...
TPTC16U3.00B1.00R06 0.630 3.000 6 2.250 1.752 1.000 1.024 0.374 0.236 1.810 TC*T16...
TPTC16U4.00B1.50R07 0.630 4.000 7 3.000 2.000 1.500 1.193 0.626 0.394 3.170 TC*T16...

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit Center bolt
(Optional parts)
TPTC16U2.00B0.75R04 TS 40B100I H-TB2W M-1000 BT15S (TCS9.525-35-I)
TPTC16U2.50B0.75R05 TS 40B100I H-TB2W M-1000 BT15S (C0.375X1.125H)
TPTC16U3.00B1.00R06 TS 40B100I H-TB2W M-1000 BT15S (C0.500X1.375H)
TPTC16U4.00B1.50R07 TS 40B100I H-TB2W M-1000 BT15S -

EP TC 16
S q u a re S h o u l d e r m i l l i n g c u t te r s w i t h s h re d i n s e r t

A.R. = +5.5°~ +6.5°, R.R. = -11.5°~ -11.3°

øDc

øDs

ap
90° Lf ℓs
L

Inch Max. ap øDc z øDs ℓs Lf L lb Insert

EPTC16U2.00W1.25R04 0.630 2.000 4 1.250 2.250 2.250 4.500 1.700 TC*T16**

SPARE PARTS
Designation Clamping screw Grip Lubricant Torx bit
EPTC16... TS 40B100I H-TB2W M-1000 BT15S

Reference pages
Inserts → D048, Standard cutting conditions → D049

Tungaloy D047
 LPTC 16
S q u a re s h o u l d e r m i l l i n g c u t te r s f o r ro u g h i n g w i t h s h re d i n s e r t
A.R. = +5.5°~ +6.5°, R.R. = -11.5°~ -11.3°
Lf
ℓ b

øDc

øDb
ød
a
Max. ap
Shoulder Milling

Inch Max. ap øDc Z eff z øDb Lf ød ℓ a b Ib Insert

LPTC16U2.50B1.00L2.4R03 2.402 2.500 3 12 2.350 3.350 1.000 1.024 0.374 0.236 2.820 TC*T16...
LPTC16U3.00B1.25L3.0R04 2.992 3.000 4 20 2.839 4.000 1.250 1.260 1.260 0.315 4.670 TC*T16...

SPARE PARTS
Designation Clamping screw Grip Lubricant Center bolt Torx bit
LPTC16U2.50B1.00L2.4R03 TS 40B100I H-TB2W M-1000 SD-08-C8 BT15S
LPTC16U3.00B1.25L3.0R04 TS 40B100I H-TB2W M-1000 SD10-54 BT15S

INSERT
TC GT- M J TC M T-N M J
T T
ap

ap
A
A

rε rε
bs bs
ød ød

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated
AH3135

Max.
AH120

Designation rε ap A ød T bs

TCGT160608PDER-MJ 0.031 0.630 z z 0.630 0.539 0.228 0.039

TCMT160620PDER-NMJ 0.079 0.630 z z 0.630 0.524 0.228 0.079

Note: When using the NMJ chipbreaker no specific insert orientation is necessary. z: Line up

Reference pages

Standard cutting conditions → D049

D048 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS

ISO Workpiece materials Hardness Priority Grades Chip- Cutting speed Feed per tooth
breaker Vc (sfm) fz (ipt)
- 300 HB First choice AH3135 NMJ* 330 - 830 0.003 - 0.006
Low carbon steels
(1015, 1020, etc.) For finishing
- 300 HB AH3135 MJ 330 - 830 0.003 - 0.008

- 300 HB First choice AH3135 NMJ* 330 - 760 0.003 - 0.006

Carbon steels, Alloy steels
(1055, 4140, etc.)
- 300 HB For finishing AH3135 MJ 330 - 760 0.003 - 0.008

Shoulder Milling
30 - 40 HRC First choice AH3135 NMJ* 330 - 590 0.003 - 0.006
Prehardened steel
(NAK80, PX5, etc.)
30 - 40 HRC For finishing AH3135 MJ 330 - 590 0.003 - 0.008

- First choice AH3135 NMJ* 300 - 660 0.003 - 0.006

Stainless steels
(304, 316, etc)
- For finishing AH3135 MJ 300 - 660 0.003 - 0.008

150 - 250 HB First choice AH120 NMJ* 460 - 830 0.003 - 0.006
Grey cast irons
(No.25, No.30, etc.)
150 - 250 HB For finishing AH120 MJ 460 - 830 0.003 - 0.010

150 - 250 HB First choice AH120 NMJ* 460 - 830 0.003 - 0.006
Ductile cast irons
(60-40-18, 80-55-06, etc.) For finishing
150 - 250 HB AH120 MJ 460 - 830 0.003 - 0.010

- First choice AH120 NMJ* 70 - 200 0.003 - 0.006

Titanium alloys
(Ti-6AI-4V, etc.) For finishing
- AH120 MJ 70 - 200 0.003 - 0.007

- First choice AH120 NMJ* 70 - 130 0.003 - 0.005

Heat-resistant alloys
(Inconel718, etc.)
- For finishing AH120 MJ 70 - 130 0.003 - 0.006

* When you use the NMJ chipbreaker, please set up the feed less than 0.006 ipt.

Tungaloy D049
 E PAV 06
Sq u a re s h o u l der m i l l i ng end m i l l s i n sm al l d i a m e te r

A.R. = +6.0°~ +7.6°, R.R. = -37.1°~ -32.4°

øDc

øDs
R R

ap
90° Lf ℓs
L
Shoulder Milling

Inch Max. ap øDc z øDs ℓs Lf L lb Insert

EPAV06U0.31C0.37R01 0.236 0.313 1 0.375 2.463 0.787 3.250 0.090 AVGT06**
EPAV06U0.37C0.37R01 0.236 0.375 1 0.375 2.463 0.787 3.250 0.090 AVGT06**
EPAV06U0.37C0.37R01L 0.236 0.375 1 0.375 2.622 1.378 4.000 0.110 AVGT06**
EPAV06U0.50C0.50R02 0.236 0.500 2 0.500 2.463 0.787 3.250 0.150 AVGT06**
EPAV06U0.50C0.50R03 0.236 0.500 3 0.500 2.463 0.787 3.250 0.150 AVGT06**
EPAV06U0.50C0.50R02L 0.236 0.500 2 0.500 3.388 1.362 4.750 0.220 AVGT06**
EPAV06U0.62C0.62R03 0.236 0.625 3 0.625 2.713 0.787 3.500 0.260 AVGT06**
EPAV06U0.62C0.62R04 0.236 0.625 4 0.625 2.713 0.787 3.500 0.260 AVGT06**
EPAV06U0.62C0.62R03L 0.236 0.625 3 0.625 4.122 1.378 5.500 0.420 AVGT06**

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EPAV06... CSPB-2H M-1000 IP-6DB

H PAV 06-M
Sq u a re s h o u l der m i l l i ng end m i l l s i n sm al l d i a m e te r ; M od u l a r h e a d w i t h Tu n gF l ex c on n e c t i on

A.R. = +6.0°~ +7.6°, R.R. = -37.1°~ -32.4°

L6
R
Lf
C Ts R R
A T
øDc

øD3

90° ap A A-A cross section

Metric Max. ap øDc z L6 Lf C T øD3 Ts lb Insert

HPAV06M010M06R02 6 10 2 34.5 20 5 7 9.5 M6 0.010 AVGT06...
HPAV06M012M06R02 6 12 2 34.5 20 5 7 10 M6 0.010 AVGT06...
HPAV06M012M06R03 6 12 3 34.5 20 5 7 10 M6 0.010 AVGT06...
HPAV06M016M08R03 6 16 3 42 25 8 10 13 M8 0.030 AVGT06...
HPAV06M016M08R04 6 16 4 42 25 8 10 13 M8 0.030 AVGT06...
• See page D147 for TungFlex modular shank.

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HPAV06M... CSPB-2H M-1000 IP-6DB

Reference pages
Inserts, Standard cutting conditions → D051

D050 www.tungaloyamerica.com
 INSERT
AVG T- M J AVG T- A J
rε B T

ap
A
bs

P Steel 
M Stainless 
K Cast iron 

Shoulder Milling
N Non-ferrous 
S Superalloys  : First choice
H Hard materials  : Second choice
Coated Un-
coated

AH3135
Max.

KS05F
Designation rε ap AH120 A B T bs

AVGT060302PBER-MJ 0.008 0.236 z z 0.315 0.197 0.106 0.059

AVGT060304PBER-MJ 0.016 0.236 z z 0.315 0.197 0.106 0.051
AVGT060308PBER-MJ 0.031 0.236 z z 0.315 0.197 0.102 0.035
AVGT060302PBFR-AJ 0.008 0.236 z 0.315 0.197 0.106 0.059
AVGT060304PBFR-AJ 0.016 0.236 z 0.315 0.197 0.106 0.051
AVGT060308PBFR-AJ 0.031 0.236 z 0.315 0.197 0.102 0.035

z: Line up

STA NDA RD CUT TING CONDITIONS

Workpiece materials Hardness Priority Grades Chip- Cutting speed Feed per tooth
ISO Vc (sfm) fz (ipt)
breaker
Low carbon steel First choice
- 300 HB AH3135 MJ 755 - 1400 0.003 - 0.005
(1018, 1020, 1026, etc.)

Carbon steel and alloy steel

- 300 HB First choice AH3135 MJ 490 - 1150 0.003 - 0.005
(1055, 4140, etc.)

Prehardened steel
30 - 40 HRC First choice AH120 MJ 650 - 1020 0.003 - 0.005
(NAK80, PX5, etc.)

Stainless steel First choice

- AH3135 MJ 650 - 1020 0.002 - 0.004
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

150 - 250 HB First choice AH120 MJ 650 - 1080 0.003 - 0.005
(Class 25, Class 30, etc.)

Ductile cast iron

150 - 250 HB First choice AH120 MJ 490 - 790 0.003 - 0.005
(60-40-18, 60-55-06, etc.)

Aluminum alloys (Si < 13%) - First choice KS05F AJ 2130 - 3280 0.003 - 0.005

Titanium alloys (Ti-6Al-4V, etc.) - First choice AH120 MJ 150 - 230 0.002 - 0.0035

Superalloys (Inconel 718, etc.) - First choice AH120 MJ 100 - 160 0.002 - 0.003

(H13, etc.) 40 - 50 HRC First choice AH120 MJ 150 - 230 0.002 - 0.003
Hardened steel
(D2, etc.) 50 - 60 HRC First choice AH120 MJ 150 - 210 0.0015 - 0.0025

Tungaloy D051
 A PPLICATION R A NGE
Helical
interpolation Hole enlarging
Plunging and
Shoulder Ramping traversing
milling
Slotting

Feed

A
Shoulder Milling

ø+1, 2 ø+3
ap

ap
ae

Max. depth of Max. Max. Max. cutting

ramping plunging Min. Max. machining width in
Tool dia. machining
cut angle depth enlarging
Inch øDc ap θ A øD1 øD2 øD3 * ae
EPAV06U0.31… 0.313 0.236 - - - - - -

EPAV06U0.37… 0.375 0.236 3º 0.012 0.591 0.748 0.709 0.374

EPAV06U0.50… 0.500 0.236 3º 0.020 0.709 0.906 0.866 0.453

EPAV06U0.62… 0.625 0.236 2.5º 0.024 0.984 1.220 1.181 0.610

*Flat bottom hole

D052 www.tungaloyamerica.com
MEMO

Shoulder Milling

Tungaloy D053
 TP O 07
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l s w i t h AO M T / AO GT 0 7 i n s e r t s
A.R. = +7°, R.R. = +13°~ +18°
øDb
ød

b
R
a
R R

ℓ
Lf
ap
Shoulder Milling

øDc 90°
Inch øDc z øDb Lf ød ℓ a b lb Air hole Insert
TPO07R200U0075A12 2.000 12 1.693 1.575 0.750 0.789 0.315 0.197 0.660 with AO*T0702...

SPARE PARTS
Designation Clamping screw Center bolt Wrench
TPO07R200U0075A12 CSTB-2.5L046 C0.375X1.125H T-7DB

E PO07
H i g h p re c i s i o n s q u a re s h o u l d e r e n d m i l l s w i t h AO M T / AO GT 0 7 i n s e r t s
A.R. = +7°, R.R. = +13°~ +18°

R
øDc

øDs
R R

ap
90° Lf Rs
L

Inch øDc z øDs ℓs Lf L lb Air hole Insert

EPO07R050U0050-02 0.500 2 0.500 2.250 0.750 3.000 0.140 with AO *T0702...
EPO07R063U0063-04 0.625 4 0.625 2.563 0.937 3.500 0.250 with AO *T0702...
EPO07R075U0075-05 0.750 5 0.750 2.875 1.125 4.000 0.410 with AO *T0702...
EPO07R100U0075-03 1.000 3 0.750 2.000 1.500 3.500 0.400 with AO*T0702...
EPO07R100U0100W07 1.000 7 1.000 2.281 1.500 3.781 0.680 with AO *T0702...
*The øDc in the above table shows the diameter when MJ and AJ chipbreakers **The Lf and L in the above table show the lengths when MJ chipbreaker is used.
are used. When HJ chipbreaker is used, the tool diameter is equal to the above When AJ chipbreaker is used, the lengths are equal to Lf, L + 0.004". When HJ
shown øDc + 0.024". chipbreaker is used, the lengths are equal to Lf, L + 0.02".

SPARE PARTS
Designation Clamping screw Wrench
EPO07R... CSTB-2.5L046 T-7DB

Reference pages
Inserts → D055, Standard cutting conditions → D056

D054 www.tungaloyamerica.com
HP O 07-M
Hig h p re c i s i o n s quare sho ul d er end m i l l s ( Tun gR e c ) f or Tu n gF l ex , w i t h AO M T/ AO GT07 i n s e r t s
A.R. = +7°, R.R. = +13°~ +18°
L6
Lf Ts
R

L4 T
A R R

øDc

øD3
90° ap C A A-A cross section

Shoulder Milling
Metric øDc z L6 Lf L4 C T øD3 Ts Kg Air hole Insert
HPO07R012MM06-02 12 2 39.5 25 - 5 7 9.8 M6 0.01 with AO*T0702...
HPO07R012MM08-02 12 2 42 25 20 8 10 12.8 M8 0.02 with AO*T0702...
HPO07R016MM08-04 16 4 42 25 - 8 10 12.8 M8 0.03 with AO*T0702...
HPO07R016MM10-04 16 4 49 30 20 10 15 17.8 M10 0.05 with AO*T0702...
HPO07R020MM10-05 20 5 49 30 - 10 15 17.8 M10 0.06 with AO*T0702...
HPO07R025MM12-07 25 7 57 35 - 10 17 20.8 M12 0.1 with AO*T0702...

SPARE PARTS
Designation qClamping screw Lubricant Wrench
HPO07R012MM0*-02 SR-10503833-S M-1000 T-7DB
HPO07R016 - 025... CSTB-2.5L046 M-1000 T-7DB

INSERT
AOM T07-M J AO M T 0 7 -H J
A rε T A rε T
B
B

AOGT07-AJ
A rε T
B

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys  : First choice
H Hard materials : Second choice
Coated Un-
coated

Max.
AH725
AH140

KS15F

Designation rε ap A B T

AOMT070202PDPR-MJ 0.008 0.276 z z 0.315 0.185 0.091

AOMT070204PDPR-MJ 0.016 0.276 z z 0.315 0.185 0.091
AOMT070208PDPR-MJ 0.031 0.276 z z 0.315 0.185 0.091
AOMT070216PDPR-MJ 0.063 0.276 z z 0.315 0.185 0.091
AOMT070208PDPR-HJ 0.031 0.031 z z 0.346 0.185 0.094
AOGT070204PDFR-AJ 0.016 0.252 z 0.319 0.185 0.091
z: Line up
Reference pages
Standard cutting conditions → D056

Tungaloy D055
 STA NDA RD CUT TING CONDITIONS

Hardness Cutting speed Feed per tooth: fz (ipt)

ISO Workpiece material Grade
HB Vc (sfm) MJ HJ AJ
Low carbon steel
< 200 AH725 300 - 660 0.002 - 0.004 0.015 - 0.035 -
(1018, 1020, 1026, etc.)

High carbon steel and alloy steel

200 - 300 AH725 300 - 500 0.002 - 0.004 0.015 - 0.035 -
(1045, 4140, etc.)

Tool steel
150 - 300 AH725 260 - 400 0.002 - 0.004 0.015 - 0.035 -
(H13, etc.)

Stainless steel
Shoulder Milling

- AH140 300 - 500 0.002 - 0.004 0.015 - 0.035 -

(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron 150 - 250 AH725 330 - 600 0.002 - 0.004 0.015 - 0.035 -
(Class 25, Class 30, etc.)

Ductile cast iron 150 - 250 AH725 260 - 500 0.002 - 0.004 0.015 - 0.035 -
(60-40-18, 60-55-06, etc.)

Aluminum alloys (Si < 13%) - KS15F 1000 - 3300 - - 0.003 - 0.008

Aluminum alloys (Si ≥ 13%) - KS15F 330 - 660 - - 0.003 - 0.008

Titanium alloys
- AH725 60 - 160 0.002 - 0.004 0.008 - 0.035 -
(Ti-6Al-4V, etc.)

Superalloys
- AH725 60 - 115 0.002 - 0.003 0.008 - 0.024 -
(Inconel 718, etc.)

· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power, workpiece rigidity, and spindle
· To avoid build up edge on the cutting edges (aluminum machining), use a water output. When the cutting width, depth, or overhang length is large, set Vc and fz to
soluble coolant. the lower recommended values and check the machine power and vibration.
· When cutting an interrupted surface or a casted skin, the feed per tooth (fz) should · For application range see page D068.
be reduced to the lower recommended value shown in the above table.

CAUTION A RY POINTS WHEN USING HJ INSERTS

HJ type inserts are designed for high feed machining. TungRec 07 type HJ inserts
Please note the following when using HJ inserts:
1. The shape of HJ insert differs from that of other inserts (MJ,
Standard conditions
AJ). However the same insert pocket can be used.
0.040
2. When using HJ inserts, all the inserts on the cutter body
must be HJ type. Do not use other types of inserts (MJ and AJ
Depth of cut: ap (in)

0.032
types) with HJ inserts on the same cutter body.
3. When using CAD/CAM, please program it as a radius cutter. 0.024
The table below shows the corner R when programming and
the uncut area (t). 0.016
4. With HJ inserts, the tool diameter increases by 0.024" Steel Stainless
Superalloys
over the diameter øDc shown in the table. 0.008

Cast Iron
0 0.008 0.016 0.024 0.032 0.040
Max. ap: 0.031"

Feed per tooth: fz (ipt)

Max. depth Main cutting Corner R when Amount left
of cut edge length programming uncut
max ap (in) W (in) t (in)

rў=
R 0.020" 0.016
0.031”
t Amount left 0.031 0.118
10° uncut R 0.039" 0.012

Tool diameter: w R
øDc + 0.024" Corner R when
programming

D056 www.tungaloyamerica.com
MEMO

Shoulder Milling

Tungaloy D057
 TP S 11
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l s w i t h A S M T / A S GT 1 1 i n s e r t s
A.R. = +8.7°~ +18°, R.R. = −5.3°~ −19.4°

øDb
ød R

b
a
R R

R
Lf
ap
øDc 90°
Shoulder Milling

Inch Max. ap øDc z øDb ød ℓ Lf b a Ib Air hole Insert

TPS11200RBU 0.417 2.000 7 1.693 0.750 0.750 1.575 0.197 0.315 0.880 with AS*T11T3...
TPS11300RBU 0.417 3.000 10 2.283 1.000 1.024 1.969 0.236 0.374 2.640 with AS*T11T3...
TPS11400RBU 0.417 4.000 11 3.150 1.500 1.457 2.480 0.394 0.626 5.290 with AS*T11T3...

SPARE PARTS
Designation Clamping screw Lubricant Wrench Center bolt
(Optional parts)
TPS11200RBU CSPB-2.5 M-1000 IP-8D (C0.375x1.125H)
TPS11300RBU CSPB-2.5 M-1000 IP-8D (C0.500x1.375H)
TPS11400RBU CSPB-2.5 M-1000 IP-8D (TMBA-0.750H)

E PS11
H i g h p re c i s i o n s q u a re s h o u l d e r e n d m i l l s w i t h A S M T / A S GT 1 1 i n s e r t s
A.R. = +8.7°~ +18°, R.R. = −5.3°~ −19.4°

R
øDc

øDs
R R
ap
90° Lf Rs
L

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert

EPS11050RLU 0.417 0.500 1 0.625 3.750 1.250 5.000 0.350 with AS*T11T3...
EPS11050RSU 0.417 0.500 1 0.625 2.362 0.984 3.346 0.240 with AS*T11T3...
EPS11062RLU 0.417 0.625 2 0.625 4.250 1.500 5.750 0.440 with AS*T11T3...
EPS11062RSU 0.417 0.625 2 0.625 2.362 0.984 3.346 0.240 with AS*T11T3...
EPS11075RLU 0.417 0.750 2 0.750 5.250 2.000 7.250 0.790 with AS*T11T3...
EPS11075RSBU 0.417 0.750 3 0.750 2.362 1.181 3.543 0.370 with AS*T11T3...
EPS11100RLU 0.417 1.000 2 1.000 5.750 2.750 8.500 1.700 with AS*T11T3...
EPS11100RSBU 0.417 1.000 4 1.000 2.362 1.378 3.740 0.700 with AS*T11T3...
EPS11100RSBU-3/4 0.417 1.000 4 0.750 2.360 1.378 3.738 0.480 with AS*T11T3...
EPS11125RLU 0.417 1.250 2 1.250 7.000 3.000 10.000 3.190 with AS*T11T3...
EPS11125RSBU 0.417 1.250 5 1.250 2.362 1.378 3.740 1.120 with AS*T11T3...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EPS11050RLU CSPB-2.5 M-1000 IP-8D
EPS11050RSU CSPB-2.5S M-1000 IP-8D
EPS11062RLU CSPB-2.5 M-1000 IP-8D
EPS11062RSU CSPB-2.5S M-1000 IP-8D
EPS11075RLU CSPB-2.5 M-1000 IP-8D
EPS11075RSBU CSPB-2.5S M-1000 IP-8D
EPS11100RLU CSPB-2.5 M-1000 IP-8D
EPS11100RSBU CSPB-2.5 M-1000 IP-8D
EPS11100RSBU-3/4 CSPB-2.5 M-1000 IP-8D
EPS11125RLU CSPB-2.5 M-1000 IP-8D
EPS11125RSBU CSPB-2.5 M-1000 IP-8D

Reference pages
Inserts → D061, Standard cutting conditions → D062 - D063

D058 www.tungaloyamerica.com
T L S11
H i g h l y p ro d u c t i v e s q u a re s h o u l d e r m i l l s f o r ro u g h i n g w i t h A S M T / A S GT 1 1 i n s e r t s
A.R. = +8.7°~ +18°, R.R. = −5.3°~ −19.4°
øDb
ød R

b
a

R
R R

Lf
ap

Shoulder Milling
øDc 90º
Inch Max. ap øDc Z eff z øDb Lf ød ℓ a b Ib Air hole Insert
TLS11R200U0075A04 1.921 2.000 4 20 1.875 2.356 0.750 0.750 0.315 0.197 1.330 with AS*T11T3...

SPARE PARTS
Designation Clamping screw Lubricant Wrench Center bolt
TLS11R200U0075A04 CSPB-2.5 M-1000 IP-8D CM10X40H

ELS11
H i g h l y p ro d u c t i v e e n d m i l l s f o r ro u g h i n g w i t h A S M T / A S GT 1 1 i n s e r t s

A.R. = +8.7° ~ +18°, R.R. = -5.3° ~ -19.4°

øDs
øDc

R R

ap
90° Lf Rs
L

Inch Max. ap øDc Z eff z øDs ℓs Lf L Ib Air hole Insert

ELS11R100U0100W02 1.197 1.000 2 6 1.000 2.250 1.500 3.750 0.670 with AS*T11T3...
ELS11R125U0125W03 1.535 1.250 3 12 1.250 2.250 2.250 4.500 1.330 with AS*T11T3...
ELS11R150U0125W03 1.575 1.500 3 12 1.250 2.329 2.171 4.500 1.330 with AS*T11T3...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
ELS11... CSPB-2.5 M-1000 IP-8D

Reference pages
Inserts → D061, Standard cutting conditions → D062 - D063

Tungaloy D059
 H PO11-M
H i g h p re c i s i o n sq uare sho ul d er end m i l l s (Tu n gR e c ) f or Tu n gF l ex , w i t h A S M T/ A S GT11 i n s e r t s

A.R. = +8.7° ~ +18°, R.R. = -5.3° ~ -19.4°

L6
Lf Ts R
C A T
R R

øDc

øD3
ap A
Shoulder Milling

90° A-A cross section

Metric Max. ap øDc z L6 Lf C T øD3 Ts Kg Air hole Insert
HPO11R020MM10-02 10.6 20 2 49 30 10 15 17.8 M10 0.06 with AS*T11T3...
HPO11R025MM12-03 10.6 25 3 57 35 10 17 20.8 M12 0.1 with AS*T11T3...
HPO11R032MM16-03 10.6 32 3 63 40 12 22 28.8 M16 0.2 with AS*T11T3...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HPO11R020MM10-02 CSPB-2.5S M-1000 IP-8D
HPO11R025, 032... CSPB-2.5 M-1000 IP-8D

Reference pages
Inserts → D061, Standard cutting conditions → D062 - D063

D060 www.tungaloyamerica.com
 INSERT
ASM T11-M J AS M T 1 1 -M S
A T A T

B
rε rε

ASGT11-AJ
A T

Shoulder Milling
B
rε
P Steel   
M Stainless 
K Cast iron  
N Non-ferrous  
S Superalloys   : First choice
: Second choice
H Hard materials
Coated Un-
Cermet coated

DS1100
rε Max.

KS05F
AH725
AH130
AH120

AH140

NS740
T3130
Designation T1215 A B T
T1115

ap

ASMT11T304PDPR-MJ 0.016 0.417 z z z z z z 0.457 0.264 0.146

ASMT11T308PDPR-MJ 0.031 0.417 z z z z z z z z 0.457 0.264 0.146
ASMT11T312PDPR-MJ 0.047 0.417 z z z z z 0.457 0.264 0.146
ASMT11T316PDPR-MJ 0.063 0.417 z z z z z 0.457 0.264 0.146
ASMT11T320PDPR-MJ 0.079 0.417 z z 0.457 0.264 0.146
ASMT11T330PDPR-MJ 0.118 0.417 z z 0.457 0.264 0.146
ASMT11T304PDPR-MS 0.016 0.417 z z 0.457 0.264 0.146
ASGT11T304PDFR-AJ 0.016 0.417 z z 0.457 0.264 0.146
ASGT11T308PDFR-AJ 0.031 0.417 z z 0.457 0.264 0.146

z: Line up

Tungaloy D061
 STA NDA RD CUT TING CONDITIONS
TPS11/EP S 1 1/HP O11 t y p e
Brinell Feed per tooth: fz (ipt)
ISO Workpiece material hardness Priority Grade Cutting speed:
HB Vc (sfm) MJ MS AJ
0.004 -
~ 200 First choice AH725 330 - 820 - -
0.008

Low carbon steel 0.004 -

~ 200 For wear resistance T3130 330 - 820 - -
(1018, 1020, 1026, etc.) 0.008

0.002 -
~ 200 For surface appearance NS740 330 - 820 - -
0.006
Shoulder Milling

0.004 -
200 ~ 300 First choice AH725 330 - 660 - -
0.008
High carbon steel and
0.004 -
alloy steel 200 ~ 300 For wear resistance T3130 330 - 660 - -
0.008
(1045, 4140, etc.)
0.002 -
200 ~ 300 For surface appearance NS740 330 - 660 - -
0.005

0.003 -
150 ~ 300 First choice AH725 330 - 500 - -
Tool steel 0.006
(H13, etc.) 0.003 -
150 ~ 300 For wear resistance T3130 330 - 500 - -
0.006

Stainless steel 0.003 -

- - AH130 260 - 660 - -
(304SS, 316SS, 17-4 PH, etc.) 0.008

150 ~ 250 First choice AH120 330 - 820 0.005 - 0.01 - -

Gray cast iron
(Class 25, Class 30, etc.)
T1215
150 ~ 250 For wear resistance 330 - 820 0.005 - 0.01 - -
T1115

150 ~ 250 First choice AH120 260 - 660 0.005 - 0.01 - -

Ductile cast iron
(60-40-18, 60-55-06, etc.)
T1215
150 ~ 250 For wear resistance 260 - 660 0.005 - 0.01 - -
T1115

Aluminum alloys 0.002 -

- - DS1100 1000 - 3300 - -
(Si < 13%) 0.008

Aluminum alloys 0.002 -

- - DS1100 330 - 660 - -
(Si ≥ 13%) 0.008

0.002 -
Copper alloys - - KS05F 660 - 1650 - -
0.008

Titanium alloys 0.003 -

- - AH130 60 - 200 - -
(Ti-6Al-4V, etc.) 0.006

Superalloys 0.003 -
- - AH725 60 - 130 - -
(Inconel 718, etc.) 0.005

CAUTION A RY POINT IN MODIF Y ING CUT TER BODIES

When using inserts with corner radius rε
rε * 0.079"(2.0 mm), standard cutter Corner radius rε (in) The dimension of modifying (in)
bodies have to be modified “R”. 0.016 - 0.063 Unnecessary
(Only for TPS11, EPS11, TLS11, ELS11,
0.079 - 0.118 0.080
HPO11)
• From 2nd row onwards, please use
insert with rε = 0.016" or 0.031"
• For application range see page D068.

D062 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Roughi ng t ype T LS11 / ELS11
Brinell Cutting speed: Feed per tooth: fz (ipt)
ISO Workpiece material hardness Priority Grade
HB Vc (sfm) MJ MS AJ
0.002 -
~ 200 First choice AH725 330 - 820 - -
Low carbon steel 0.007
(1018, 1020, 1026, etc.) 0.002 -
~ 200 For wear resistance T3130 330 - 820 - -
0.007

0.003 -
200 ~ 300 First choice AH725 330 - 660 - -
High carbon steel and alloy steel 0.006

Shoulder Milling
(1045, 4140, etc.) 0.003 -
200 ~ 300 For wear resistance T3130 330 - 660 - -
0.006

0.003 -
150 ~ 300 First choice AH725 330 - 500 - -
Tool steel 0.006
(H13, etc.) 0.003 -
150 ~ 300 For wear resistance T3130 330 - 500 - -
0.006

Stainless steel 0.003 -

- - AH130 330 - 500 - -
(304SS, 316SS, 17-4 PH, etc.) 0.006

0.004 -
150 ~ 250 First choice AH120 330 - 800 - -
Gray cast iron 0.007
(Class 25, Class 30, etc.) 0.004 -
T1215
150 ~ 250 For wear resistance 330 - 800 - -
T1115 0.007

0.004 -
150 ~ 250 First choice AH120 260 - 650 - -
Ductile cast iron 0.007
(60-40-18, 60-55-06, etc.) 0.004 -
T1215
150 ~ 250 For wear resistance 260 - 650 - -
T1115 0.007

Aluminum alloys 0.002 -

- - DS1100 650 - 1650 - -
(Si ≥ 13%) 0.007

Aluminum alloys 0.002 -

- - DS1100 330 - 650 - -
(Si ≥ 13%) 0.007

Titanium alloys 0.003 -

- - AH130 60 - 200 - -
(Ti-6Al-4V, etc.) 0.006

Superalloys 0.003 -
- - AH725 60 - 130 - -
(Inconel 718, etc.) 0.005

· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power, workpiece rigidity, and
· To avoid build up edge on the cutting edges (aluminium machining), use a spindle output. When the cutting width, depth, or overhang length is large,
water soluble coolant. set Vc and fz to the lower recommended values and check the machine
· When cutting an interrupted surface or a casted skin, the feed per tooth (fz) power and vibration.
should be reduced to the lower recommended value shown in the above
table.

Tungaloy D063
 MEMO
Shoulder Milling

D064 www.tungaloyamerica.com
T P O 18
H i g h p re c i s i o n s q u a re s h o u l d e r m i l l i n g c u t te r s w i t h AO M T / AO GT 1 8 i n s e r t s

A.R. = +14° ~ +17°, R.R. = +22° ~ +31°

øDb
ød R

b
a
R R

R
Lf
ap

Shoulder Milling
øDc 90°

Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Air hole Insert

TPO18R200U0075A05 0.657 2.000 5 1.625 1.570 0.750 0.750 0.315 0.197 0.780 with AO*T1805...
TPO18R250U0075A06 0.657 2.500 6 2.125 1.570 0.750 0.750 0.315 0.197 1.320 with AO*T1805...
TPO18R300U0100A07 0.657 3.000 7 2.250 1.750 1.000 1.000 0.374 0.236 1.890 with AO*T1805...
TPO18R400U0150A08 0.657 4.000 8 3.000 2.000 1.500 1.060 0.630 0.354 3.140 without AO*T1805...
TPO18R500U0150A09 0.657 5.000 9 4.000 2.000 1.500 1.060 0.630 0.354 6.270 without AO*T1805...
TPO18R600U0200A10 0.657 6.000 10 4.750 2.000 2.000 1.060 0.748 0.394 8.370 without AO*T1805...

SPARE PARTS
Designation Clamping screw Grip Torx bit Center bolt
(Optional parts)
TPO18R200,250... CSTB-4L093 H-TBS BT15M (C0.375X1.125H)
TPO18R300... CSTB-4L120 H-TBS BT15M (C0.500X1.375H)
TPO18R400,500,600... CSTB-4L120 H-TBS BT15M -

Reference pages
Inserts, Standard cutting conditions → D067

Tungaloy D065
 E PO18
H i g h p re c i s i o n s q u a re s h o u l d e r e n d m i l l s w i t h AO M T / AO GT 1 8 i n s e r t s

A.R. = +14° ~ +17°, R.R. = +22° ~ +31°

øDs
øDc
R R

ap
90° Lf Rs
L
Shoulder Milling

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert

EPO18R100U0100W02 0.657 1.000 2 1.000 2.250 1.750 4.000 0.730 with AO*T1805...
EPO18R100U0100W02L 0.657 1.000 2 1.000 2.250 2.750 5.000 0.910 with AO*T1805...
EPO18R125U0125W03 0.657 1.250 3 1.250 2.250 2.250 4.500 1.320 with AO*T1805...
EPO18R125U0125W03L 0.657 1.250 3 1.250 2.250 4.250 6.500 1.880 with AO*T1805...
EPO18R150U0125W03L 0.657 1.500 3 1.250 2.250 4.250 6.500 2.420 with AO*T1805...
EPO18R150U0125W04 0.657 1.500 4 1.250 2.250 2.250 4.500 1.460 with AO*T1805...
EPO18R200U0125W05 0.657 2.000 5 1.250 2.250 2.250 4.500 1.680 with AO*T1805...

SPARE PARTS
Designation Clamping screw Wrench
EPO18R100U... CSTB-4L085 T-15DB
EPO18R125U - 200U... CSTB-4L093 T-15DB

Reference pages
Inserts, Standard cutting conditions → D067

D066 www.tungaloyamerica.com
 INSERT
AOM T18-M J AO GT 1 8 -AJ
A T A
rε rε T

B
B
P Steel 
M Stainless 
K Cast iron 


Shoulder Milling
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated Un-
coated

rε Max.

AH725
AH140

KS15F
Designation ap A B T

AOMT180508PDPR-MJ 0.031 0.657 z z 0.768 0.421 0.220

AOMT180516PDPR-MJ 0.063 0.657 z z 0.768 0.421 0.220
AOMT180524PDPR-MJ 0.094 0.657 z z 0.768 0.421 0.220
AOMT180532PDPR-MJ 0.126 0.657 z z 0.768 0.421 0.220
AOGT180504PDFR-AJ 0.016 0.657 z 0.780 0.425 0.240
AOGT180508PDFR-AJ 0.031 0.657 z 0.780 0.425 0.240
z: Line up

STA NDA RD CUT TING CONDITIONS

T P O 18/E PO18 t y p e

Brinell Cutting speed Feed per tooth: fz (ipt)

ISO Workpiece material hardness Grade
Vc (sfm) MJ AJ
HB
Low carbon steel
~ 200 AH725 330 - 820 0.003 - 0.010 -
(1018, 1020, 1026, etc.)

High carbon steel and alloy steel

200 ~ 300 AH725 330 - 750 0.003 - 0.008 -
(1045, 4140, etc.)

Tool steel
150 ~ 300 AH725 330 - 600 0.003 - 0.008 -
(H13, etc.)

Stainless steel
- AH140 330 - 660 0.003 - 0.008 -
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

150 ~ 250 AH725 330 - 820 0.003 - 0.010 -
(Class 25, Class 30, etc.)

Ductile cast iron

150 ~ 250 AH725 260 - 660 0.003 - 0.010 -
(60-40-18, 60-55-06, etc.)

Aluminum alloys (Si < 13%) - KS15F 1000 - 3300 - 0.002 - 0.010

Aluminum alloys (Si ≥ 13%) - KS15F 330 - 660 - 0.002 - 0.010

Titanium alloys
- AH725 60 - 200 0.003 - 0.007 -
(Ti-6Al-4V, etc.)

Superalloys
- AH725 60 - 130 0.003 - 0.006 -
(Inconel 718, etc.)

· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power, workpiece rigidity, and spindle
· To avoid build up edge on the cutting edges (aluminum machining), use a water output. When the cutting width, depth, or overhang length is large, set Vc and fz
soluble coolant. to the lower recommended values and check the machine power and vibration.
· When cutting an interrupted surface or a casted skin, the feed per tooth (fz)
should be reduced to the lower recommended value shown in the above table.

Tungaloy D067
 A PPLICATION R A NGE

Helical Hole
Plunging and interpolation enlarging
Shoulder Ramping traversing
milling Slotting

Feed

A
Shoulder Milling

øD1, 2 øD3 ae
ap

ap

Max. Max. Max. cutting

Tool dia. Chipbreaker Max. depth ramping plunging Min. Max. machining width in
of cut machining
angle depth enlarging
Inch øDc ap θ° A øD1 øD2 øD3* ae
0.500 MJ, AJ 0.276 7.5 0.020 0.750 0.862 0.862 0.480
EPO07R050U0050-02
0.524 HJ 0.031 4.5 0.030 0.786 - - 0.406

0.625 MJ, AJ 0.276 5 0.020 0.938 1.112 1.112 0.610

EPO07R063U0063-04
0.649 HJ 0.031 4 0.030 0.974 - - 0.531

0.750 MJ, AJ 0.276 3.5 0.020 1.125 1.362 1.362 0.730

EPO07R075U0075-05
0.774 HJ 0.031 2.5 0.030 1.161 - - 0.656

1.000 MJ, AJ 0.276 2.4 0.020 1.500 1.862 1.862 0.980

EPO07R100U…
1.024 HJ 0.031 2 0.030 1.536 - - 0.906

EPS11050... 0.500 MJ, MS, AJ 0.417 6 0.020 0.590 0.882 0.882 0.480

EPS11062... 0.625 MJ, MS, AJ 0.417 5 0.020 0.790 1.332 1.332 0.610

EPS11075... 0.750 MJ, MS, AJ 0.417 3 0.020 1.100 1.382 1.382 0.730

EPS11100... 1.000 MJ, MS, AJ 0.417 2 0.020 1.500 1.882 1.882 0.980

EPS11125... 1.250 MJ, MS, AJ 0.417 1.5 0.020 2.050 2.382 2.382 1.230

EPO18R100U… 1.000 MJ, AJ 0.657 5.5 0.039 1.272 1.764 1.764 0.961

EPO18R125U… 1.250 MJ, AJ 0.657 3.5 0.039 1.772 2.264 2.264 1.211

EPO18R150U… 1.500 MJ, AJ 0.657 2.7 0.039 2.272 2.764 2.764 1.461

T/EPO18R200U… 2.000 MJ, AJ 0.657 1.9 0.039 3.272 3.764 3.764 1.961

Max. Max. Max. cutting

Tool dia. Max. depth Min.
Chipbreaker ramping plunging Max. machining width in
of cut machining
angle depth enlarging
Inch øDc ap θ° A øD1 øD2 øD3* ae
2.000 MJ, AJ 0.276 0.9 0.020 3.000 3.960 3.862 1.980
TPO07R200U0075A12
2.024 HJ 0.031 0.6 0.030 3.036 4.008 - 1.906

TPS11200RBU 2.000 MJ, MS, AJ 0.417 0.7 0.020 3.460 3.900 3.882 1.950

TPS11300RBU 3.000 MJ, MS, AJ 0.417 0.4 0.020 5.830 6.260 5.882 3.130

TPS11400RBU 4.000 MJ, MS, AJ 0.417 0.3 0.020 7.400 7.830 7.882 3.920

TPO18R250U0075A06 2.500 MJ, AJ 0.657 1.4 0.039 4.272 4.921 4.764 2.461

TPO18R300U0100A07 3.000 MJ, AJ 0.657 1.1 0.039 5.272 5.921 5.764 2.961

TPO18R400U0150A08 4.000 MJ, AJ 0.657 0.8 0.039 7.272 7.921 7.764 3.961

TPO18R500U0150A09 5.000 MJ, AJ 0.657 0.6 0.039 9.272 9.921 9.764 4.961

TPO18R600U0200A10 6.000 MJ, AJ 0.657 0.5 0.039 11.272 11.921 11.764 5.961

*Flat bottom hole

Notes: Corner rε for dimensions of øD1, øD2, and øD3: rε = 0.016" for EPO07 / EPS11 and rε = 0.031" for EPO18.

D068 www.tungaloyamerica.com
T P D 05
H i g h l y d e n s e s q u a re s h o u l d e r m i l l s w i t h s m a l l S D M T / S D H T 0 5 i n s e r t s
A.R. = +5°, R.R. = -7° ~ +12°
øDb
ød
a

b
R
Lf
ap
øDc 90˚ Right hand (R) shown.

Shoulder Milling
Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Air hole Insert
TPD05R150U0075A08 0.157 1.500 8 1.461 1.570 0.750 0.750 0.313 0.170 0.220 with SD*T0502...
TPD05R200U0075A10 0.157 2.000 10 1.750 1.570 0.750 0.750 0.313 0.170 0.440 with SD*T0502...

SPARE PARTS
Designation Clamping screw Wrench Center bolt
(Optional parts)
TPD05... CSPB-2L043 IP-6DB (C0.375X1.125H)

EP D 05
H i g h l y d e n s e s q u a re s h o u l d e r e n d m i l l s w i t h s m a l l S D M T / S D H T 0 5 i n s e r t s
A.R. = +5°, R.R. = -7° ~ +12°
øDc

øDs
ap
90˚ Lf Rs
L Fig.1 Fig.2
Right hand (R) shown.

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Shank Insert Shank type
EPD05R050U0050-02 0.157 0.500 2 0.500 1.780 1.220 3.000 0.220 with Straight SD*T0502... Fig.1
EPD05R063U0063-03 0.157 0.625 3 0.625 2.000 1.500 3.500 0.440 with Straight SD*T0502... Fig.1
EPD05R075U0075W04 0.157 0.750 4 0.750 2.030 1.720 3.750 0.440 with Weldon SD*T0502... Fig.2
EPD05R100U0100W05 0.157 1.000 5 1.000 2.280 1.720 4.000 0.660 with Weldon SD*T0502... Fig.2
EPD05R125U0100W06 0.157 1.250 6 1.250 2.280 1.720 4.000 1.100 with Weldon SD*T0502... Fig.2

SPARE PARTS
Designation Clamping screw Wrench
EPD05... CSPB-2L043 IP-6DB

ELD 05
H i g h l y d e n s e s q u a re s h o u l d e r e n d m i l l s f o r ro u g h i n g w i t h s m a l l S D M T / S D H T 0 5 i n s e r t s
A.R. = +5°, R.R. = -3°
øDs
øDc

ap
Lf Rs
L

Inch Max. ap øDc Z eff z øDs ℓs Lf L Ib Air hole Insert

ELD05R075U0075W02 0.799 0.750 2 10 0.750 2.031 1.219 3.250 0.440 with SD*T0502...
ELD05R025M25.0W03 0.953 1.000 3 18 1.000 2.250 1.500 3.750 0.670 with SD*T0502...

SPARE PARTS
Designation Clamping screw Wrench
ELD05... CSPB-2L043 IP-6DB

Reference pages
Inserts → D070, Standard cutting conditions → D070 - D071

Tungaloy D069
 INSERT
SD M T05-M J S D H T 0 5 -AJ
ød T ød T

rε rε

P Steel 
M Stainless 

Shoulder Milling

K Cast iron
N Non-ferrous 
S Superalloys  : First choice
H Hard materials : Second choice
Coated Un-
coated

rε Max.

AH725
AH140
Designation T ød

TH10
ap

SDMT050204PN-MJ 0.016 0.157 z z 0.094 0.200

SDHT050204FN-AJ 0.016 0.157 z 0.094 0.200
z: Line up

STA NDA RD CUT TING CONDITIONS

Bore, shank type TPD 0 5/ EPD 0 5
Workpiece material Brinell hardness Grade Cutting speed Feed per tooth
ISO HB Vc (sfm) fz (ipt)
Low carbon steel
~ 200 AH725 750 - 1050 0.0015 - 0.004
(1018, 1020, 1026, etc.)

High carbon steel

200 ~ 300 AH725 500 - 750 0.0015 - 0.004
(1045, 1055, etc.)

Alloyed steel
150 ~ 300 AH725 500 - 750 0.0015 - 0.004
(4140, 8620, etc.)

Tool steel
~ 300 AH725 350 - 440 0.001 - 0.0035
(W1-8, etc.)

Stainless steel
- AH140 330 - 650 0.001 - 0.0035
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

150 ~ 250 AH725 500 - 820 0.002 - 0.005
(Class 25, Class 30, etc.)

Ductile cast iron

150 ~ 250 AH725 330 - 590 0.002 - 0.005
(60-40-18, 60-55-06, etc.)

Aluminum alloys
- TH10 1150 - 1600 0.002 - 0.006
(Si < 13%)

Aluminum alloys
- TH10 330 - 650 0.002 - 0.006
(Si ≥ 13%)

Titanium alloys
- AH725 98 - 197 0.001 - 0.0035
Ti-6Al-4V, etc.

Heat-resistant alloys
Inconel 718, etc. - AH725 33 - 131 0.001 - 0.003

* For deep and wide cutting, set the Vc and fz to the lower recommended limits and check the vibration and spindle load of the machine.

D070 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Roughing type E LD 0 5
Workpiece material Brinell hardness Grade Cutting speed Feed per tooth
ISO HB Vc (sfm) fz (ipt)
Low carbon steel
~ 200 AH725 330 - 820 0.0015 - 0.004
(1018, 1020, 1026, etc.)

High carbon steel

200 ~ 300 AH725 330 - 660 0.0015 - 0.004
(1045, 1055, etc.)

Alloyed steel
150 ~ 300 AH725 330 - 660 0.0015 - 0.004
(4140, 8620, etc.)

Tool steel

Shoulder Milling
~ 300 AH725 330 - 400 0.0012 - 0.0035
(W1-8, etc.)

Stainless steel
- AH140 300 - 500 0.0012 - 0.0035
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

150 ~ 250 AH725 330 - 820 0.002 - 0.005
(Class 25, Class 30, etc.)

Ductile cast iron

150 ~ 250 AH725 260 - 660 0.002 - 0.005
(60-40-18, 60-55-06, etc.)

Aluminum alloys
- TH10 660 - 1650 0.002 - 0.006
(Si < 13%)

Aluminum alloys
- TH10 330 - 650 0.002 - 0.006
(Si ≥ 13%)

Titanium alloys
- AH725 98 - 197 0.001 - 0.0035
Ti-6Al-4V, etc.

Heat-resistant alloys
- AH725 33 - 131 0.001 - 0.003
Inconel 718, etc.

Tungaloy D071
 TPW 13
S q u a re s h o u l d e r m i l l s w i t h s c re w c l a m p e d S W M T / S W GT 1 3 i n s e r t s

A.R. = +11.5°, R.R. = -13° ~ -10.5°

ød
a

b
R
Lf
ap
Shoulder Milling

øDc 90° Right hand (R) shown.

Inch Max. ap øDc z Lf ød ℓ a b Ib Air hole Insert

TPW13R200U0075A03 0.394 2.000 3 1.575 0.750 0.750 0.315 0.197 0.660 with SW*T1304...
TPW13R200U0075A04 0.394 2.000 4 1.575 0.750 0.750 0.315 0.197 0.660 with SW*T1304...
TPW13R200U0075A05 0.394 2.000 5 1.575 0.750 0.750 0.315 0.197 0.660 with SW*T1304...
TPW13R300U0100A04 0.394 3.000 4 1.969 1.000 1.024 0.374 0.236 1.760 with SW*T1304...
TPW13R300U0100A06 0.394 3.000 6 1.969 1.000 1.024 0.374 0.236 1.540 with SW*T1304...
TPW13R300U0100A08 0.394 3.000 8 1.969 1.000 1.024 0.374 0.236 1.760 with SW*T1304...
TPW13R400U0150A05 0.394 4.000 5 1.969 1.500 1.378 0.626 0.394 3.530 with SW*T1304...
TPW13R400U0150A07 0.394 4.000 7 1.969 1.500 1.378 0.626 0.394 3.310 with SW*T1304...
TPW13R400U0150A10 0.394 4.000 10 1.969 1.500 1.378 0.626 0.394 3.310 with SW*T1304...
TPW13R500U0150A06 0.394 5.000 6 2.480 1.500 1.457 0.626 0.394 5.510 with SW*T1304...
TPW13R500U0150A08 0.394 5.000 8 2.480 1.500 1.457 0.626 0.394 5.290 with SW*T1304...
TPW13R500U0150A12 0.394 5.000 12 2.480 1.500 1.457 0.626 0.394 5.510 with SW*T1304...
TPW13R600U0200A08 0.394 6.000 8 2.480 2.000 1.496 0.748 0.433 7.940 with SW*T1304...
TPW13R600U0200A12 0.394 6.000 12 2.480 2.000 1.496 0.748 0.433 8.160 with SW*T1304...
TPW13R600U0200A15 0.394 6.000 15 2.480 2.000 1.496 0.748 0.433 8.160 without SW*T1304...

SPARE PARTS
qClamping
Designation Lubricant wShim screw Center bolt Center bolt 1 eShim Wrench for q Wrench for w
screw
TPW13R200... CSPB-3.5 M-1000 DTS5-3.5SS - C0.375X1.25H FSSP1102 IP-15D P-3.5
TPW13R300... CSPB-3.5 M-1000 DTS5-3.5SS - C0.5X1.5H FSSP1102 IP-15D P-3.5
TPW13R400,500... CSPB-3.5 M-1000 DTS5-3.5SS TMBA-0.750H - FSSP1102 IP-15D P-3.5
TPW13R600... CSPB-3.5 M-1000 DTS5-3.5SS - - FSSP1102 IP-15D P-3.5

e q
w
Insert
 

Reference pages
Inserts → D074, Standard cutting conditions → D075

D072 www.tungaloyamerica.com
E PW 13
S q u a re s h o u l d e r e n d m i l l s w i t h s c re w c l a m p e d S W M T / S W GT 1 3 i n s e r t s

A.R. = +11.5°, R.R. = -13° ~ -10.5°

øDs
øDc
Lf Rs
90˚ L

Shoulder Milling
Right hand (R) shown.

Metric Max. ap øDc z øDs ℓs Lf L Kg Air hole Insert

EPW13R032M32.0-02 10 32 2 32 80 35 115 0.6 with SW*T1304...
EPW13R040M32.0-03 10 40 3 32 80 35 115 0.7 with SW*T1304...
EPW13R050M32.0-03 10 50 3 32 80 40 120 0.9 with SW*T1304...
EPW13R050M32.0-04 10 50 4 32 80 40 120 0.9 with SW*T1304...
EPW13R063M32.0-04 10 63 4 32 80 40 120 1 with SW*T1304...
EPW13R063M32.0-05 10 63 5 32 80 40 120 1 with SW*T1304...
EPW13R080M32.0-04 10 80 4 32 80 40 120 1.3 with SW*T1304...
EPW13R080M32.0-06 10 80 6 32 80 40 120 0.8 with SW*T1304...

SPARE PARTS
Designation qClamping screw Lubricant wShim screw eShim Wrench for q Wrench for w
EPW13R032, 040... CSPB-3.5 M-1000 - - IP-15D -
EPW13R050 - 080... CSPB-3.5 M-1000 DTS5-3.5SS FSSP1102 IP-15D P-3.5

e q
w
Insert

Reference pages
Inserts → D074, Standard cutting conditions → D075

Tungaloy D073
 INSERT
SW GT1304- M J S W M T 1 3 0 4 -M J
A T A T

rε
rε
17º 17º

ød

bs
ød

bs
SW M T1304- M L S W M T 1 3 0 4 -M S
Shoulder Milling

A T A T

rε

rε
ød
17º 17º
ød

bs
bs

SW GT1304- A J
A T
rε

17º
ød

bs

P Steel   
M Stainless 
K Cast iron  
N Non-ferrous  
S Superalloys : First choice
H Hard materials : Second choice
Un-
Coated Cermet coated
DS1100

rε Max.
KS05F
AH130
AH120

AH140

NS740
T1115
T1215
T3130

Designation ap A ød T bs

SWGT1304PDPR-MJ 0.031 0.394 z z 0.535 0.535 0.197 0.055

SWMT1304PDPR-MJ 0.031 0.394 z z z z z z z 0.535 0.535 0.197 0.055
SWMT1304PDER-ML 0.031 0.394 z z 0.535 0.535 0.197 0.055
SWMT1304PDPR-MS 0.031 0.394 z z 0.535 0.535 0.197 0.055
SWGT1304PDFR-AJ 0 0.394 z z 0.535 0.535 0.197 0.063

z: Line up

D074 www.tungaloyamerica.com
 STA N DA RD CUT TING CONDITIONS TPW / EPW13 T Y PE
Roughing Light cutting to finishing
Cutting (Depth of cut: ap * 0.040") (Depth of cut: ap ) 0.040")
Workpiece Recommended
ISO speed Feed per tooth: fz (ipt) Feed per tooth: fz (ipt)
material insert grade
Vc (sfm)
MJ ML MS AJ MJ ML MS AJ
AH120 0.002 - 0.002 - 0.002 - 0.002 -
330 - 890 - - - -
(First choice) 0.010 0.008 0.008 0.007
T3130 0.002 - 0.002 -
Mild steel 500 - 980 - - - - - -
(Priority on wear resistance) 0.010 0.008
Low carbon steel
(< 180HB) AH130 / AH140 0.002 - 0.002 - 0.002 - 0.002 -
260 - 590 - - - -
(Priority on impact resistance) 0.010 0.008 0.008 0.007

Shoulder Milling
NS740 0.002 - 0.002 -
330 - 980 - - - - - -
(Priority on surface finish) 0.006 0.005
AH120 0.002 - 0.002 - 0.002 - 0.002 -
330 - 760 - - - -
(First choice) 0.008 0.006 0.007 0.005
T3130 0.002 - 0.002 -
Carbon steel 490 - 920 - - - - - -
(Priority on wear resistance) 0.008 0.007
Alloy steel
(< 300HB) AH130 / AH140 0.002 - 0.002 -
260 - 490 - - - - - -
(Priority on impact resistance) 0.008 0.007
NS740 0.002 - 0.002 -
330 - 760 - - - - - -
(Priority on surface finish) 0.006 0.005
AH120 0.002 - 0.002 - 0.002 - 0.002 -
330 - 590 - - - -
Die steel (First choice) 0.006 0.005 0.005 0.004
(< 30HRC) T3130 0.002 - 0.002 -
330 - 590 - - - - - -
(Priority on wear resistance) 0.006 0.005
AH130 / AH140 0.002 - 0.002 - 0.002 - 0.002 -
260 - 650 - - - -
Stainless steel (First choice) 0.008 0.007 0.007 0.006
(< 250HB) AH120 0.002 - 0.002 - 0.002 - 0.002 -
490 - 820 - - - -
(Priority on wear resistance) 0.008 0.006 0.007 0.005
T1215 0.002 - 0.002 -
330 - 820 - - - - - -
(First choice) 0.008 0.007
Gray cast iron
AH120 0.002 - 0.002 - 0.002 - 0.002 -
330 - 820 - - - -
(Priority on impact resistance) 0.008 0.006 0.007 0.005
Aluminum alloys DS1100 / KS05F 0.002 - 0.002 -
980 - 3300 - - - - - -
(Si < 13 %) (First choice) 0.008 0.008
Aluminum alloys DS1100 / KS05F 0.002 - 0.002 -
260 - 980 - - - - - -
(Si ≥ 13 %) (First choice) 0.008 0.008
DS1100 / KS05F 0.002 - 0.002 -
Copper alloys 660 - 1650 - - - - - -
(First choice) 0.008 0.008

Notes:
 When machining at large depth of cut or large cutting width, Vc and fz should be reduced.  When machining mild steel, carbon steel or alloy steel in wet conditions T3130 is
 As a rule, dry machining (including air blow) is recommended. But, for excessive chip recommended. In this case, Vc and fz should be reduced.
welding, such as when machining stainless steels, use a water soluble cutting fluid. In this  TPW13 type can not be used for ramping, plunging and drilling.
case, use AH140 and set the cutting speed to Vc ) 328 sfm.

Tungaloy D075
 TP Q 11, 18
S q u a re s h o u l d e r m i l l s w i t h LQ M U t y p e d o u b l e s i d e d to u g h i n s e r t s w i t h 4 e d g e s

A.R. = +4° ~ +5°, R.R. = +13° ~ +15°

øDb
ød R
a

b
R R

R
ap
Lf
øDc
Shoulder Milling

90° Right hand (R) shown.

Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Air hole Insert

TPQ11R200U0075A06 0.354 2.000 6 1.693 1.575 0.750 0.787 0.320 0.187 0.88 with LQMU1107...
TPQ11R250U0075A07 0.354 2.500 7 1.693 1.575 0.750 0.787 0.320 0.187 1.32 with LQMU1107...
TPQ11R300U0100A10 0.354 3.000 10 2.165 1.969 1.000 1.024 0.383 0.219 2.31 with LQMU1107...
TPQ11R400U0150A12 0.354 4.000 12 3.150 1.969 1.500 1.496 0.633 0.375 4.41 with LQMU1107...
TPQ18R200U0075A03 0.630 2.000 3 1.772 1.575 0.750 0.750 0.320 0.187 0.88 with LQMU1808...
TPQ18R250U0100A04 0.630 2.500 4 2.165 1.969 1.000 1.024 0.383 0.219 1.76 with LQMU1808...
TPQ18R300U0100A05 0.630 3.000 5 2.165 1.969 1.000 1.024 0.383 0.219 2.43 with LQMU1808...
TPQ18R400U0150A06 0.630 4.000 6 3.150 1.969 1.500 1.496 0.633 0.375 3.75 with LQMU1808...
TPQ18R500U0150A08 0.630 5.000 8 3.150 2.480 1.500 1.693 0.626 0.394 6.17 with LQMU1808...
TPQ18R600U0200A09 0.630 6.000 9 3.937 2.480 2.000 1.811 0.758 0.437 9.04 without LQMU1808...

SPARE PARTS
Designation Clamping screw Grip Torx bit Center bolt
(Optional parts)
TPQ11R200,250... CSTB-3.5L115 SW6-SD BLDT10/S7 (C0.375X1.125H)
TPQ11R300... CSTB-3.5L115 SW6-SD BLDT10/S7 (C0.500X1.375H)
TPQ11R400... CSTB-3.5L115 SW6-SD BLDT10/S7 -
TPQ18R200,250... CSTB-3.5L115 SW6-SD BLDT10/S7 (C0.375X1.125H)
TPQ18R300... CSTB-3.5L115 SW6-SD BLDT10/S7 (C0.500X1.137H)
TPQ18R400,500,600... CSTB-3.5L115 SW6-SD BLDT10/S7 -

E PQ11
S q u a re s h o u l d e r e n d m i l l s w i t h LQ M U t y p e d o u b l e s i d e d to u g h i n s e r t s w i t h 4 e d g e s

A.R. = +4° ~ +5°, R.R. = +13° ~ +15°

R
øDs
øDc

R R

ap
90° Lf Rs
L Fig.1 Fig.2
Right hand (R) shown.

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert Shank style

EPQ11R100U0100W02 0.354 1.000 2 1.000 2.280 1.220 3.500 0.750 with LQMU1107... Fig.2
EPQ11R125U0125W03 0.354 1.250 3 1.250 2.500 1.500 4.000 1.540 with LQMU1107... Fig.2
EPQ11R150U0125W04 0.354 1.500 4 1.250 2.250 1.750 4.000 1.650 with LQMU1808... Fig.2

SPARE PARTS
Designation Clamping screw Grip Grip 1 Torx bit Wrench*
EPQ11...
*:Monoblock type substitutionCSTB-3.5L115
wrench SW6-SD - BLDT10/S7 T-10D

Reference pages
Inserts, Standard cutting conditions → D077

D076 www.tungaloyamerica.com
 INSERT
LQM U 11/18-M J

B T

A
rε
P Steel  
M Stainless 

Shoulder Milling
K Cast iron  
N Non-ferrous
S Superalloys   : First choice
H Hard materials : Second choice
Coated

rε Max.
AH725
AH120
Designation ap AH140 A T B

LQMU110704PNER-MJ 0.016 0.354 z z z 0.433 0.327 0.016

LQMU110708PNER-MJ 0.031 0.354 z z z 0.433 0.327 0.031
LQMU110716PNER-MJ 0.063 0.354 z z z 0.433 0.327 0.063
LQMU180804PNER-MJ 0.016 0.630 z z z 0.689 0.433 0.016
LQMU180808PNER-MJ 0.031 0.630 z z z 0.689 0.433 0.031
LQMU180816PNER-MJ 0.063 0.630 z z z 0.689 0.433 0.063
LQMU180824PNER-MJ 0.094 0.630 z z z 0.689 0.433 0.094

z: Line up

STA NDA RD CUT TING CONDITIONS

Workpiece material Hardness Grade Cutting speed Feed per tooth
ISO Vc (sfm) fz (ipt)
HB
Low carbon steel
- 200 AH725 330 - 800 0.004 - 0.010
(1018, 1020, 1026, etc.)

High carbon steel

200 - 300 AH725 330 - 750 0.004 - 0.008
(1045, 1055, etc.)

Alloyed steel
150 - 300 AH725 330 - 750 0.004 - 0.008
(4140, 8620, etc.)

Tool steel
- 300 AH725 330 - 600 0.004 - 0.008
(H13, D2, etc.)

Stainless steel
- AH140 300 - 600 0.004 - 0.010
(304SS, 316SS, 17-4 PH, etc.)

Gray cast iron

150 - 250 AH120 450 - 800 0.004 - 0.010
(Class 25, Class 30, etc.)

Ductile cast iron

150 - 250 AH120 450 - 800 0.004 - 0.010
(60-40-18, 60-55-06, etc.)

Heat-resistant alloy
- AH725 65 - 160 0.003 - 0.008
(Inconel 718, etc.)
· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power, work piece rigidity and spindle
· When cutting an interrupted surface or a casted skin, the feed per tooth (fz) should output. When the cutting width, depth or over hang length is large, set Vc and fz to
be reduced to the lower recommended value shown in the above table. the lower recommended values and check the machine power and vibration.

Tungaloy D077
 TPM 11, 16
S q u a re s h o u l d e r m i l l s w i t h L M M U t y p e t a n g e n t i a l c l a m p e d i n s e r t w i t h 4 e d g e s

A.R. = +5° ~ +6°, R.R. = +9° ~ +13°

øDb
ød

b
R
a
R R

Lf R
ap
Shoulder Milling

øDc 90˚ Right hand (R) shown.

Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Air hole Insert

TPM11R200U0075A05 0.381 2.000 5 1.770 1.570 0.750 0.750 0.320 0.240 0.66 with LMMU1107...
TPM11R250U0075A06 0.381 2.500 6 1.770 1.570 0.750 0.750 0.320 0.240 1.10 with LMMU1107...
TPM11R300U0100A06 0.381 3.000 6 2.170 1.970 1.000 0.750 0.390 0.240 1.98 with LMMU1107...
TPM11R300U0100A08 0.381 3.000 8 2.170 1.970 1.000 0.750 0.390 0.240 2.20 with LMMU1107...
TPM11R400U0150A08 0.381 4.000 8 3.070 1.970 1.500 1.060 0.630 0.310 3.09 with LMMU1107...
TPM11R400U0150A11 0.381 4.000 11 3.070 1.970 1.500 1.060 0.630 0.310 3.31 with LMMU1107...
TPM16R300U0100A05 0.594 3.000 5 2.170 1.970 1.000 0.750 0.390 0.240 2.20 with LMMU1609...
TPM16R400U0150A06 0.594 4.000 6 3.070 1.970 1.500 1.060 0.630 0.310 3.53 with LMMU1609...
TPM16R500U0150A07 0.594 5.000 7 3.070 2.480 1.500 1.060 0.630 0.390 6.61 with LMMU1609...

SPARE PARTS
Center bolt
Designation qClamping screw Grip Torx bit (Optional parts)
TPM11R200, 250... CSTB-3.5L110 H-TB BT15S (C0.375X1.125H)
TPM11R300... CSTB-3.5L110 H-TB BT15S (C0.500X1.375H)
q
TPM11R400... CSTB-3.5L110 H-TB BT15S (TMBA-0.750H)
TPM16R300... CSTB-5L159 H-TB BT20S (C0.500X1.375H)
TPM16R400, 500... CSTB-5L159 H-TB BT20S (TMBA-0.750H)

EP M 11
S q u a re s h o u l d e r e n d m i l l s w i t h L M M U t y p e t a n g e n t i a l c l a m p e d i n s e r t w i t h 4 e d g e s

A.R. = +5° ~ +6°, R.R. = +9° ~ +13°

R
øDs
øDc

R R

ap
90˚
Lf Rs
L
Right hand (R) shown.

Inch Max. ap øDc z øDs ℓs Lf L Ib Air hole Insert

EPM11R125U0125W03 0.381 1.250 3 1.250 2.250 1.750 4.000 0.66 with LMMU1107...
EPM11R150U0125W04 0.381 1.500 4 1.250 2.250 1.750 4.000 1.10 with LMMU1107...

SPARE PARTS
Designation Clamping screw Wrench
EPM11... CSTB-3.5L110 T-15DB

Reference pages
Inserts → D079, Standard cutting conditions → D080

D078 www.tungaloyamerica.com
T LM 11
S q u a re s h o u l d e r m i l l s f o r ro ug hi ng w i t h LM M U t y p e t a n ge n t i a l c l a m p e d i n s e r t w i t h 4 e d ge s

A.R. = +5° ~ +6°, R.R. = +9° ~ +13°

øDb
ød R

b
a

R
R R

ap
Lf

Shoulder Milling
øDc 90º
Inch Max. ap øDc Z eff z øDb Lf ød ℓ a b Ib Air hole Insert
TLM11R200U0075A03 2.303 2.000 3 21 1.850 2.750 0.750 0.750 0.315 0.157 1.78 with LMMU1107...
TLM11R250U0100A04 2.634 2.500 4 32 2.323 3.250 1.000 0.750 0.374 0.197 3.33 with LMMU1107...

SPARE PARTS
Designation Clamping screw Grip Torx bit Center bolt
TLM11R200… SM35-114-H0 H-TB BT15S SD06-A2
TLM11R250… SM35-114-H0 H-TB BT15S SD08-52

INSERT
L M M U 11/16-MJ
A T
B

rε

P Steel   
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys   : First choice
H Hard materials : Second choice
Coated

rε Max.
AH725
AH120
AH140

T3130

Designation A B T
T1115

ap

LMMU110708PNER-MJ 0.031 0.381 z z z z z 0.460 0.413 0.280

LMMU110716PNER-MJ 0.063 0.381 z z z z z 0.453 0.413 0.280
LMMU110724PNER-MJ 0.094 0.381 z z z z z 0.445 0.413 0.280
LMMU110732PNER-MJ 0.126 0.381 z z z z z 0.437 0.413 0.280
LMMU160908PNER-MJ 0.031 0.594 z z z z z 0.681 0.630 0.375
LMMU160916PNER-MJ 0.063 0.594 z z z z z 0.673 0.630 0.375
LMMU160924PNER-MJ 0.094 0.594 z z z z 0.665 0.630 0.375
LMMU160932PNER-MJ 0.126 0.594 z z z z 0.661 0.630 0.375
z: Line up

Reference pages
Standard cutting conditions → D080

Tungaloy D079
 STA NDA RD CUT TING CONDITIONS
TPM11, 16 / EPM11
ISO Brinell hardness Cutting speed Feed per tooth
Workpiece materials HB Priority Grade Vc (sfm) fz (ipt)
- 200 First choice AH725 350 - 800 .005 - .012
Low carbon steels
- 200 For impact resistance AH140 260 - 600 .005 - .012
1018, 8620 etc.
- 200 For wear resistance T3130 390 - 800 .005 - .012

200 - 300 First choice AH725 350 - 750 .005 - .012

High carbon steels
200 - 300 For impact resistance AH140 260 - 600 .005 - .012
F-61 80 etc.
200 - 300 For wear resistance T3130 390 - 800 .005 - .012
Shoulder Milling

150 - 300 First choice AH725 350 - 750 .005 - .010

Alloyed steels
150 - 300 For impact resistance AH140 260 - 500 .005 - .010
4140, 4340 etc.
150 - 300 For wear resistance T3130 390 - 800 .005 - .010

- 300 First choice AH725 350 - 600 .005 - .010

Tool steels
A-6, D-1, D-2 etc. - 300 For impact resistance AH140 260 - 390 .005 - .010

- 300 For wear resistance T3130 350 - 600 .005 - .010

Stainless steels
- First choice AH140 300 - 600 .005 - .012
300 series, 304, 316 etc.

Grey cast irons 150 - 250 First choice AH120 450 - 800 .005 - .012
250 etc. 150 - 250 For wear resistance T1115 450 - 800 .005 - .012

Ductile cast irons 150 - 250 First choice AH120 360 - 640 .005 - .012
450-10S etc. 150 - 250 T1115 360 - 640 .005 - .012
For wear resistance

Heat-resisting alloy
- First choice AH725 75 - 200 .004 - .008
Inconel 718 / Ti-6Al-4V etc.

· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power, work piece rigidity
· When cutting an interrupted surface or a casting skin, the feed (fz) and spindle output. When the cutting width, depth or overhang
should be reduced to the lower recommended value shown in the length is large, set Vc and fz to the lower recommended values and
above table. check the machine power and vibration.

TLM11
Brinell hardness Cutting speed Feed per tooth
ISO Workpiece materials Priority Grade
HB Vc (sfm) fz (ipt)
- 200 First choice AH725 330 - 800 .004 - .009
Low carbon steels
- 200 For impact resistance AH140 260 - 600 .004 - .009
1018, 8620 etc.
- 200 For wear resistance T3130 330 - 800 .004 - .009

200 - 300 First choice AH725 330 - 660 .004 - .009

High carbon steels
F-61 80 etc. 200 - 300 For impact resistance AH140 260 - 500 .004 - .009

200 - 300 For wear resistance T3130 330 - 660 .004 - .009

150 - 300 First choice AH725 330 - 660 .003 - .008

Alloyed steels
4140, 4340 etc. 150 - 300 For impact resistance AH140 260 - 500 .003 - .008

150 - 300 For wear resistance T3130 330 - 660 .003 - .008

- 300 First choice AH725 330 - 500 .003 - .008

Tool steels
- 300 For impact resistance AH140 260 - 390 .003 - .008
A-6, D-1, D-2 etc.
- 300 For wear resistance T3130 330 - 500 .003 - .008

Stainless steels
- First choice AH140 300 - 500 .003 - .008
300 series, 304, 316 etc.

Grey cast irons 150 - 250 First choice AH120 330 - 800 .004 - .010
250 etc.
150 - 250 For wear resistance T1115 330 - 800 .004 - .010

Ductile cast irons 150 - 250 First choice AH120 260 - 500 .004 - .010
450-10S etc. 150 - 250 T1115 260 - 500 .004 - .010
For wear resistance

Heat-resisting alloy
- First choice AH725 75 - 200 .002 - .006
Inconel 718 / Ti-6Al-4V etc.

D080 www.tungaloyamerica.com
T P V16
9 0 ° s h o u l d e r m i l l i ng shel l m i l l s w i t h screw cl a m p e d X V CT16 i n s e r t s f or a l u m i n u m m a c h i n i n g

A.R. = +10° ~ +11°, R.R. = -9° ~ -5.5°

øDb
ød

b
a
R

R
Lf
R R

ap

Shoulder Milling
øDc 90˚

Max. rpm
Inch øDc z øDb ød ℓ Lf a b Ib Air hole Insert
(min-1)
TPV16R150U0075A03 1.500 3 1.421 0.750 0.750 2.000 0.315 0.170 0.440 with 30,000 XVCT1605...
TPV16R200U0075A04 2.000 4 1.890 0.750 0.750 2.000 0.315 0.170 0.890 with 27,000 XVCT1605...
TPV16R250U0100A05 2.500 5 2.165 1.000 0.750 2.000 0.375 0.197 1.340 with 24,000 XVCT1605...
TPV16R300U0100A05 3.000 5 2.362 1.000 0.750 2.000 0.375 0.197 1.920 with 21,000 XVCT1605...
TPV16R400U0150A06 4.000 6 3.150 1.500 1.059 2.500 0.625 0.319 4.280 with 19,000 XVCT1605...
TPV16R500U0150A07 5.000 7 3.740 1.500 1.059 2.500 0.625 0.319 6.700 with 17,000 XVCT1605...

SPARE PARTS
Designation Clamping screw Grip Torx bit Center bolt
(Optional parts)
TPV16R150… TS40093I/HG H-TBS BT15S (TSC9.525-35-1)
TPV16R200… TS40093I/HG H-TBS BT15S (SD06-46)
TPV16R250,300… TS40093I/HG H-TBS BT15S (SD08-47)
TPV16R400,500… TS40093I/HG H-TBS BT15S (SD12-82)

EP V16
9 0 ° e n d m i l l s w i t h s c re w c l a m p e d X V CT 1 6 i n s e r t s f o r a l u m i n u m m a c h i n i n g

A.R. = +6° ~ +10°, R.R. = -12° ~ -9°

øDc

øDs
R

R R
ap
90˚ Lf Rs
L

Max. rpm
Inch øDc z øDs ℓs Lf L Ib Air hole Insert
(min-1)
EPV16R100U0100W02 1.000 2 1.000 3.000 2.000 5.000 0.820 with 38,000 XVCT1605...
EPV16R100U0100W02L 1.000 2 1.000 4.000 3.000 7.000 1.170 with 38,000 XVCT1605...
EPV16R125U0125W02 1.250 2 1.250 4.000 2.000 6.000 1.690 with 34,000 XVCT1605...
EPV16R125U0125W02L 1.250 2 1.250 5.000 3.000 8.000 2.280 with 34,000 XVCT1605...
EPV16R125U0125W03 1.250 3 1.250 4.000 2.000 6.000 1.680 with 34,000 XVCT1605...
EPV16R125U0125W03L 1.250 3 1.250 5.000 3.000 8.000 2.270 with 34,000 XVCT1605...
EPV16R150U0125W03 1.500 3 1.250 5.000 2.000 7.000 2.080 with 30,000 XVCT1605...
EPV16R150U0125W03L 1.500 3 1.250 8.000 2.000 10.000 3.140 with 30,000 XVCT1605...

SPARE PARTS
Designation Clamping screw Grip Torx bit
EPV16R100… TS40085I/HG H-TBS BT15S
EPV16R125,150… TS40093I/HG H-TBS BT15S

Reference pages
Inserts, Standard cutting conditions → D082

Tungaloy D081
 INSERT
XV CT16-A J
A rε T

bs
B
P Steel
M Stainless
K Cast iron
N Non-ferrous 
Shoulder Milling

S Superalloys : First choice

H Hard materials : Second choice
Un-
coated

Designation rε Max. A B T bs

TH10
ap

XVCT160504R-AJ 0.016 0.630 z 0.874 0.442 0.232 0.051

XVCT160508R-AJ 0.031 0.630 z 0.874 0.442 0.232 0.039
XVCT160512R-AJ 0.047 0.610 z 0.854 0.442 0.228 0.039
XVCT160516R-AJ 0.063 0.591 z 0.835 0.442 0.226 0.039
XVCT160520R-AJ 0.079 0.571 z 0.819 0.442 0.226 0.039
XVCT160524R-AJ 0.094 0.551 z 0.800 0.442 0.224 0.039
XVCT160530R-AJ 0.118 0.551 z 0.768 0.442 0.220 0.039
XVCT160532R-AJ 0.126 0.551 z 0.756 0.442 0.220 0.039
XVCT160540R-AJ 0.157 0.512 z 0.724 0.442 0.217 0.047
XVCT160550R-AJ 0.197 0.512 z 0.724 0.442 0.213 0.016
z: Line up

STA NDA RD CUT TING CONDITIONS

Workpiece material Hardness Grade Chip- Cutting speed Feed per tooth
ISO Vc (sfm) fz (ipt)
HB breaker
900 - 1600 0.006 - 0.015
60 TH10 AJ
650 - 6600 0.004 - 0.010
Aluminum alloy
650 - 6600 0.006 - 0.012
100 TH10 AJ
650 - 5000 0.004 - 0.010
650 - 3200 0.003 - 0.006
75 TH10 AJ
Cast aluminum alloy 650 - 2600 0.003 - 0.006
Si ≤ 12% 900 - 3200 0.004 - 0.006
90 TH10 AJ
900 - 2600 0.004 - 0.006
Cast aluminum alloy 300 - 1600 0.004 - 0.006
Si > 12% 130 TH10 AJ
300 - 900 0.004 - 0.006
Copper alloys 900 - 1600 0.006 - 0.015
Pb > 1% 110 TH10 AJ
650 - 6600 0.004 - 0.010
650 - 6600 0.006 - 0.012
90 TH10 AJ
650 - 5000 0.004 - 0.010
Copper alloys
650 - 3200 0.003 - 0.006
100 TH10 AJ
650 - 2600 0.003 - 0.006
900 - 3200 0.004 - 0.006
Duroplastics, fiber plastics - TH10 AJ
900 - 2600 0.004 - 0.006
300 - 1600 0.004 - 0.006
Hard rubber - TH10 AJ
300 - 900 0.004 - 0.006

Safety guidelines
1. Use only the original inserts, cutters and spare parts. 5. Maximum RPM values are determined based on the burst test. Using RPM
2. Insert pocket must be cleaned before clamping the insert. beyond maximum values may cause insert breakage, machine damage or
3. Clamp torque of screw should be 3.3 lbf·ft. personal injury.
4. For safety reasons, use a new screw when changing the insert. 6. XVCT insert has sharp cutting edges. Always wear gloves for protection
from injury when handling.

D082 www.tungaloyamerica.com
 A PPLICATION R A NGE Helical interpolation Hole enlarging
Plunging and
Shoulder Ramping traversing
milling Slotting

Feed

A
P
L øD1, 2 ae
ap
ap

Shoulder Milling
Straight ramp down Step down Helical ramp down Hole
Max. Max. enlarging
Corner Max. depth Min. Min. Min. Max. Max.
Tool ramping plunging
radius of cut angle length depth
machining pitch/rev machining pitch/rev Max. width

Inch øDc rε ap θ° L A øD1 P øD2 P ae

EPV16R100… 1.000 0.016, 0.031 0.630 22º 1.570 0.166 1.150 0.173 1.970 0.535 0.886
EPV16R100… 1.000 0.047 0.610 22º 1.570 0.166 1.150 0.173 1.970 0.535 0.886
EPV16R100… 1.000 0.063 0.591 22º 1.500 0.146 1.150 0.173 1.970 0.520 0.886
EPV16R100… 1.000 0.079 0.571 22º 1.500 0.146 1.150 0.173 1.970 0.520 0.886
EPV16R100… 1.000 0.118, 0.126 0.551 21º 1.500 0.098 1.150 0.165 1.970 0.484 0.886
EPV16R100… 1.000 0.157, 0.197 0.512 18.5º 1.570 0.090 1.150 0.146 1.970 0.484 0.886
EPV16R125… 1.250 0.016, 0.031 0.630 16.5º 2.130 0.158 1.690 0.346 2.520 0.535 1.134
EPV16R125… 1.250 0.047 0.610 16.5º 2.130 0.158 1.690 0.346 2.520 0.535 1.134
EPV16R125… 1.250 0.063 0.591 16º 2.130 0.138 1.690 0.335 2.520 0.520 1.134
EPV16R125… 1.250 0.079 0.571 16º 2.130 0.138 1.690 0.335 2.520 0.520 1.134
EPV16R125… 1.250 0.118, 0.126 0.551 15º 2.130 0.118 1.700 0.311 2.520 0.484 1.134
EPV16R125… 1.250 0.157, 0.197 0.512 13.5º 2.200 0.098 1.700 0.280 2.520 0.484 1.134
T/EPV16R150… 1.500 0.016, 0.031 0.630 11.5º 3.110 0.158 2.330 0.409 3.150 0.535 1.417
T/EPV16R150… 1.500 0.047 0.610 11.5º 3.110 0.158 2.330 0.409 3.150 0.535 1.417
T/EPV16R150… 1.500 0.063 0.591 11º 3.150 0.138 2.330 0.390 3.150 0.520 1.417
T/EPV16R150… 1.500 0.079 0.571 11º 3.150 0.138 2.330 0.390 3.150 0.520 1.417
T/EPV16R150… 1.500 0.118, 0.126 0.551 10º 3.230 0.118 2.330 0.354 3.150 0.484 1.417
T/EPV16R150… 1.500 0.157, 0.197 0.512 8.5º 3.540 0.098 2.330 0.299 3.150 0.484 1.417
TPV16R200… 2.000 0.016, 0.031 0.630 9.5º 3.780 0.158 3.110 0.512 3.940 0.535 1.772
TPV16R200… 2.000 0.047 0.610 9.5º 3.780 0.158 3.110 0.512 3.940 0.535 1.772
TPV16R200… 2.000 0.063 0.591 9º 3.860 0.138 3.110 0.484 3.940 0.520 1.772
TPV16R200… 2.000 0.079 0.571 9º 3.860 0.138 3.110 0.484 3.940 0.520 1.772
TPV16R200… 2.000 0.118, 0.126 0.551 8º 4.060 0.118 3.110 0.429 3.940 0.484 1.772
TPV16R200… 2.000 0.157, 0.197 0.512 7º 4.330 0.098 3.110 0.374 3.940 0.484 1.772
TPV16R250… 2.500 0.016, 0.031 0.630 7º 5.120 0.158 4.130 0.535 4.960 0.535 2.232
TPV16R250… 2.500 0.047 0.610 7º 5.120 0.158 4.130 0.535 4.960 0.535 2.232
TPV16R250… 2.500 0.063 0.591 6.5º 5.350 0.138 4.130 0.504 4.960 0.520 2.232
TPV16R250… 2.500 0.079 0.571 6.5º 5.350 0.138 4.130 0.504 4.960 0.520 2.232
TPV16R250… 2.500 0.118, 0.126 0.551 6º 5.350 0.118 4.140 0.465 4.960 0.484 2.232
TPV16R250… 2.500 0.157, 0.197 0.512 5.5º 5.510 0.098 4.140 0.425 4.960 0.484 2.232
TPV16R300… 3.000 0.016, 0.031 0.630 5º 7.200 0.158 5.470 0.535 6.300 0.535 2.835
TPV16R300… 3.000 0.047 0.610 5º 7.200 0.158 5.470 0.535 6.300 0.535 2.835
TPV16R300… 3.000 0.063 0.591 4.5º 7.760 0.138 5.470 0.488 6.300 0.520 2.835
TPV16R300… 3.000 0.079 0.571 4.5º 7.760 0.138 5.470 0.488 6.300 0.520 2.835
TPV16R300… 3.000 0.118, 0.126 0.551 4º 8.150 0.118 5.480 0.433 6.300 0.484 2.835
TPV16R300… 3.000 0.157, 0.197 0.512 3.5º 8.700 0.098 5.480 0.378 6.300 0.484 2.835
TPV16R400… 4.000 0.016, 0.031 0.630 3.5º 10.310 0.158 7.040 0.508 7.870 0.535 3.543
TPV16R400… 4.000 0.047 0.610 3.5º 10.310 0.158 7.040 0.508 7.870 0.535 3.543
TPV16R400… 4.000 0.063 0.591 3º 11.650 0.138 7.040 0.437 7.870 0.520 3.543
TPV16R400… 4.000 0.079 0.571 3º 11.650 0.138 7.040 0.437 7.870 0.520 3.543
TPV16R400… 4.000 0.118, 0.126 0.551 2.5º 13.070 0.118 7.050 0.362 7.870 0.484 3.543
TPV16R400… 4.000 0.157, 0.197 0.512 2.5º 12.170 0.098 7.050 0.362 7.870 0.457 3.543
TPV16R500… 5.000 0.016, 0.031 0.630 2.5º 14.450 0.158 9.020 0.476 9.840 0.535 4.429
TPV16R500… 5.000 0.047 0.610 2.5º 14.450 0.158 9.020 0.476 9.840 0.535 4.429
TPV16R500… 5.000 0.063 0.591 2º 17.480 0.138 9.020 0.382 9.840 0.520 4.429
TPV16R500… 5.000 0.079 0.571 2º 17.480 0.138 9.020 0.382 9.840 0.520 4.429
TPV16R500… 5.000 0.118, 0.126 0.551 1.5º 21.810 0.118 9.020 0.287 9.840 0.343 4.429
TPV16R500… 5.000 0.157, 0.197 0.512 1.5º 20.310 0.098 9.020 0.287 9.840 0.343 4.429

Tungaloy D083
 EP H
H i g h p re c i s i o n s q u a re s h o u l d e r e n d m i l l s i n s m a l l d i a m e te r w i t h X H G R t y p e i n s e r t

A.R. = +14.7° ~ +19.5°, R.R. = -14.9° ~ -17.8°

øDsh6
øDc
R

R R

Max ap
90°
L1
L
Shoulder Milling

Right hand (R) shown.

Inch Max. ap øDc z øDs L L1 Insert

EPH13R050U0050-2 0.472 0.500 2 0.500 3.500 1.000 XHGR1302...
EPH18R063U0063-2 0.630 0.625 2 0.625 4.000 1.250 XHGR18T2...
EPH18R075U0075-3 0.630 0.750 3 0.750 4.000 1.500 XHGR18T2...
EPH18R100U0100-4 0.630 1.000 4 1.000 4.000 2.000 XHGR18T2...

Metric Max. ap øDc z øDs L L1 Insert

EPH11R010M10.0-2 10 10 2 10 80 21 XHGR1102...
EPH11R010M10.0-2L 10 10 2 10 100 36 XHGR1102...
EPH13R012M12.0-2 12 12 2 12 80 25 XHGR1302...
EPH13R012M12.0-2L 12 12 2 12 110 43 XHGR1302...
EPH13R013M12.0-2 12 13 2 12 110 25 XHGR1302...
EPH13R014M12.0-2 12 14 2 12 110 25 XHGR1302...
EPH18R016M16.0-2 16 16 2 16 100 33 XHGR18T2...
EPH18R016M16.0-2L 16 16 2 16 130 56 XHGR18T2...
EPH18R016M16.0-3 16 16 3 16 100 33 XHGR18T2...
EPH18R016M16.0-3L 16 16 3 16 130 56 XHGR18T2...
EPH18R017M16.0-3 16 17 3 16 130 33 XHGR18T2...
EPH18R018M16.0-3 16 18 3 16 130 33 XHGR18T2...
EPH18R020M20.0-3 16 20 3 20 110 41 XHGR18T2...
EPH18R020M20.0-3L 16 20 3 20 140 71 XHGR18T2...
EPH18R021M20.0-3 16 21 3 20 140 41 XHGR18T2...
EPH18R025M25.0-4 16 25 4 25 120 51 XHGR18T2...
EPH18R025M25.0-4L 16 25 4 25 160 88.5 XHGR18T2...
EPH18R026M25.0-4 16 26 4 25 160 51 XHGR18T2...

SPARE PARTS
Designation qClamping screw Wrench Wrench 1
EPH11R... CSP-2L033 - IP-6F
EPH13R... CSPB-2.2SH IP-7D -
EPH18R... CSPB-2.5SH IP-7D -

(Insert pocket) insert

Reference pages
Inserts → D085 - D086, Standard cutting conditions → D087

D084 www.tungaloyamerica.com
EP H w i t h sl i m s hank
Hig h p re c i s i o n s quare sho ul d er end m i l l s w i t h X H G R t y p e i n s e r t , s l i m s h a n k f or s m a l l l a t h e s
A.R. = +14.7° +19.5°, R.R. = -14.9° -17.8°

øDsh6
R

øDc
R R

ap
L1 L

Metric Max.ap øDc z øDs L L1 Insert

Shoulder Milling
EPH11R010M06.0-2 10 10 2 6 50 15 XHGR1102...
EPH13R012M07.0-2 12 12 2 7 50 17 XHGR1302...
EPH18R016M10.0-3 16 16 3 10 60 22 XHGR18T2...
EPH18R020M10.0-3 16 20 3 10 60 22 XHGR18T2...

SPARE PARTS
Designation Clamping screw Wrench Wrench 1
EPH11R010M06.0-2 CSP-2L033 - IP-6F
EPH13R012M07.0-2 CSPB-2.2SH IP-7D -
EPH18R0**M10.0-3 CSPB-2.5SH IP-7D -

INSERT XHG R11/13/18- A J X H G R 1 1 / 1 3 / 1 8 -M J

rε ℓa rε ℓa

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys : First choice
H Hard materials : Second choice
Coated
DS1200

rε Max.
AH730

Designation ap ℓa

XHGR110202ER-MJ 0.008 0.394 z 0.433

XHGR110204ER-MJ 0.016 0.394 z 0.433
XHGR110205ER-MJ 0.020 0.394 z 0.433
XHGR110208ER-MJ 0.031 0.394 z 0.433
XHGR110210ER-MJ 0.040 0.394 z 0.433
XHGR110212ER-MJ 0.047 0.394 z 0.433
XHGR110215ER-MJ 0.059 0.394 z 0.433
XHGR110216ER-MJ 0.063 0.394 z 0.433
XHGR110220ER-MJ 0.079 0.394 z 0.433
XHGR130202ER-MJ 0.008 0.472 z 0.512
XHGR130204ER-MJ 0.016 0.472 z 0.512
XHGR130205ER-MJ 0.020 0.472 z 0.512
XHGR130208ER-MJ 0.031 0.472 z 0.512
XHGR130210ER-MJ 0.040 0.472 z 0.512
XHGR130212ER-MJ 0.047 0.472 z 0.512
XHGR130215ER-MJ 0.059 0.472 z 0.512
XHGR130216ER-MJ 0.063 0.472 z 0.512
XHGR130220ER-MJ 0.079 0.472 z 0.512
XHGR18T202ER-MJ 0.008 0.630 z 0.709
XHGR18T204ER-MJ 0.016 0.630 z 0.709
XHGR18T205ER-MJ 0.020 0.630 z 0.709
XHGR18T208ER-MJ 0.031 0.630 z 0.709
XHGR18T210ER-MJ 0.040 0.630 z 0.709
XHGR18T212ER-MJ 0.047 0.630 z 0.709
XHGR18T215ER-MJ 0.059 0.630 z 0.709
XHGR18T216FR-MJ 0.063 0.630 z 0.709
XHGR18T220FR-MJ 0.079 0.630 z 0.709

Reference pages z: Line up

Inserts → D085 - D086, Standard cutting conditions → D087
Tungaloy D085
 INSERT
XHG R11/13/18- A J X H G R 1 1 / 1 3 / 1 8 -M J

rε ℓa rε ℓa

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
Shoulder Milling

S Superalloys : First choice

H Hard materials : Second choice
Coated

DS1200
rε Max.

AH730
Designation ap ℓa

XHGR110200FR-AJ 0 0.394 z 0.433

XHGR110202FR-AJ 0.008 0.394 z 0.433
XHGR110204FR-AJ 0.016 0.394 z 0.433
XHGR110205FR-AJ 0.020 0.394 z 0.433
XHGR110208FR-AJ 0.031 0.394 z 0.433
XHGR110210FR-AJ 0.039 0.394 z 0.433
XHGR110212FR-AJ 0.047 0.394 z 0.433
XHGR110215FR-AJ 0.059 0.394 z 0.433
XHGR110216FR-AJ 0.062 0.394 z 0.433
XHGR110220FR-AJ 0.078 0.394 z 0.433
XHGR130200FR-AJ 0 0.472 z 0.512
XHGR130202FR-AJ 0.008 0.472 z 0.512
XHGR130204FR-AJ 0.016 0.472 z 0.512
XHGR130205FR-AJ 0.020 0.472 z 0.512
XHGR130208FR-AJ 0.031 0.472 z 0.512
XHGR130210FR-AJ 0.039 0.472 z 0.512
XHGR130212FR-AJ 0.047 0.472 z 0.512
XHGR130215FR-AJ 0.059 0.472 z 0.512
XHGR130216FR-AJ 0.062 0.472 z 0.512
XHGR130220FR-AJ 0.078 0.472 z 0.512
XHGR18T200FR-AJ 0 0.630 z 0.709
XHGR18T202FR-AJ 0.008 0.630 z 0.709
XHGR18T204FR-AJ 0.016 0.630 z 0.709
XHGR18T205FR-AJ 0.020 0.630 z 0.709
XHGR18T208FR-AJ 0.031 0.630 z 0.709
XHGR18T210FR-AJ 0.039 0.630 z 0.709
XHGR18T212FR-AJ 0.047 0.630 z 0.709
XHGR18T215FR-AJ 0.059 0.630 z 0.709
XHGR18T216FR-AJ 0.062 0.630 z 0.709
XHGR18T220FR-AJ 0.078 0.630 z 0.709
Note: When using inserts with a corner radius in excess of 0.039", additional work to the cutter body is needed. z: Line up

D086 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
 Shoulder milling Workpiece Cutting Feed Cutting conditions
ISO speed rate
material Vc (sfm) fz (ipt) ø0.394 ≤ øDc < ø0.472 ø0.472 ≤ øDc < ø0.630 ø0.630 ≤ øDc ≤ ø1.024
Vc = 390 sfm, fz = 0.003 ipt
Carbon steels
0.001 ~
Alloy steels 200 ~ 590 ap ) 0.295" ap ) 0.354" ap ) 0.472"
0.004
< 30HRC
ae ) 0.059" ae ) 0.059" ae ) 0.079"
Vc = 390 sfm, fz = 0.0019 ipt
Alloy steels
0.001 ~
prehardened steels 160 ~ 490 ap ) 0.217" ap ) 0.256" ap ) 0.354"
0.003
30 ~ 40HRC
ae ) 0.059" ae ) 0.059" ae ) 0.079"
Vc = 330 sfm, fz = 0.0157 ipt
Stainless steels 0.001 ~

Shoulder Milling
160 ~ 490 ap ) 0.177" ap ) 0.217" ap ) 0.295"
ap

< 250HB 0.002

ae ) 0.059" ae ) 0.059" ae ) 0.079"
ae Vc = 460 sfm, fz = 0.00314 ipt
0.001 ~
Cast irons 260 ~ 560 ap ) 0.374" ap ) 0.374" ap ) 0.610"
0.004
ap: Axial depth of cut
ae ) 0.079" ae ) 0.079" ae ) 0.118"
ae: Radial depth of cut
Vc = 660 sfm, fz = 0.00275 ipt
Aluminum alloys 0.001 ~
330 ~ 980 ap ) 0.374" ap ) 0.374" ap ) 0.610"
Si < 12% 0.004
ae ) 0.079" ae ) 0.079" ae ) 0.118"
Vc = 430 sfm, fz = 0.0023 ipt
Aluminum alloys 0.001 ~
260 ~ 590 ap ) 0.374" ap ) 0.374" ap ) 0.610"
Si > 13% 0.003
ae ) 0.079" ae ) 0.079" ae ) 0.118"

 Slotting Cutting Feed Cutting conditions

Workpiece
ISO speed rate ø0.394" ≤ øDc ø0.472" ≤ øDc ø0.630 ≤ øDc ø0.709" < øDc ø0.827" < øDc
material Vc (sfm) fz (ipt) < ø0.472" < ø0.630" ≤ ø0.709" ≤ ø0.827" ≤ ø1.024"
Carbon steels Vc = 330 sfm, fz = 0.00236 ipt
0.001 ~
Alloy steels 200 ~ 590
0.004 ap ) 0.059" ap ) 0.079" ap ) 0.118" ap ) 0.098" ap ) 0.098"
< 30HRC
Alloy steels Vc = 230 sfm, fz = 0.00196 ipt
0.001 ~
prehardened steels 160 ~ 490
0.003 ap ) 0.039" ap ) 0.059" ap ) 0.079" ap ) 0.059" ap ) 0.059"
30 ~ 40HRC
Stainless steels 0.001 ~ Vc = 230 sfm, fz = 0.00157 ipt
160 ~ 490
ap

< 250HB 0.002 ap ) 0.039" ap ) 0.039" ap ) 0.059" ap ) 0.059" ap ) 0.059"

0.001 ~ Vc = 390 sfm, fz = 0.00275 ipt

Cast irons 260 ~ 560
0.004 ap ) 0.138" ap ) 0.157" ap ) 0.177" ap ) 0.138" ap ) 0.118"

Aluminum alloys 0.001 ~ Vc = 490 sfm, fz = 0.00275 ipt

330 ~ 980
Si < 12% 0.004 ap ) 0.138" ap ) 0.157" ap ) 0.177" ap ) 0.138" ap ) 0.118"

Aluminum alloys 0.001 ~ Vc = 360 sfm, fz = 0.00236 ipt

260 ~ 590
Si > 13% 0.003 ap ) 0.138" ap ) 0.157" ap ) 0.177" ap ) 0.138" ap ) 0.118"

Notes:
When slotting, use a rigid machine. Tool overhang length must be as short as possible to avoid chatter. When
When chips stay in the cutting zone during slotting or pocketing, use air to remove the tool overhang length is long, decrease the number of revolutions and
chips from the work area. feed.
If chips tend to stick to the cutting edge (such as aluminum alloy machining), use a Cutting conditions are generally limited by the rigidity and power of the
water soluble cutting fluid. machine and the rigidity of the workpiece. When setting the conditions, start
If cutting a casting skin or heavily interrupted work surface, decrease the feed per from half of the values of the standard cutting conditions and then increase
tooth and maximum depth of cut to 1/2 to 2/3 times the values shown in the table. the value gradually while making sure the machine is running normally.

Tungaloy D087
 A PPLICATION R A NGE
Ramping Small
Shoulder Slotting depth Plunging
milling plunging Drilling Enlarged
Traversing (Helical feed) hole

ѡÝ
ap

A
W

øD1, øD2 ae1

Max. depth Max. ramping Max. plunging Max. cutting Min. Max. Max. cutting
Tool ø of cut angle depth width in machinable machinable width in
plunging hole ø hole ø enlarged hole
Shoulder Milling

Type Inch øDc ap θ˚ A W øD1 øD2 * ae1 *

EPH13R050U0050-2 0.500 0.470 2.5 0.012 0.110 0.670 0.930 0.480

EPH18R063U0063-2 0.625 0.630 2.0 0.012 0.150 0.830 1.230 0.610

Straight
EPH18R075U0075-3 0.750 0.630 2.0 0.012 0.150 1.260 1.470 0.730

EPH18R100U0100-4 1.000 0.630 1.5 0.012 0.150 1.580 1.980 0.980

*Where the insert corner radius ≤ 0.008"

Notes on using large radius inserts  Insert mounting procedure (EPH-type)

When using the inserts which have a large corner radius in
excess of 0.039", additional work is needed to the corner of
Fasten the inserts in order of A to B
the body.
q After loosening the clamping screws, insert
the insert in the insert pocket of the body B
Insert corner Required rework while pushing it with your finger.
radius rε to body corner w Lightly fasten the clamping screws in order of
(in) R (in) A and B.
e For all the inserts, carry out the above steps A
0 ) rε ) 0.039 No additional work q and w.
r Securely tighten the clamping screws in order
Body 0.039 < rε ) 0.078 R0.079 of A and B .
corner R
(Refer to the standard tightening torque values.)
t For all the inserts, carry out the above step r.
y Check the condition of insert seating, clear-
ance between the insert and insert pocket, the
tool diameter, and the peripheral edge runout.

D088 www.tungaloyamerica.com
T P S 17
Squ a re s h o u l d e r m i l l s w i t h A S M T / A S GT 1 7 i n s e r t s , s u i t a b l e f or m u l t i p u r p os e m a c h i n i n g

A.R. = +9°, R.R. = -20°~ -7°

øDb
ød R R R

b
a

R
Lf
ap
øDc 90˚ Right hand (R) shown.

Shoulder Milling
Inch Max. ap øDc z Lf ød ℓ a b Ib Air hole Insert
TPS17200RBU 0.630 2.000 4 1.580 0.750 0.750 0.315 0.200 0.200 with AS*T1705...
TPS17300RBU 0.630 3.000 4 1.960 1.000 1.020 0.374 0.236 0.300 with AS*T1705...
TPS17400RBU 0.630 4.000 5 2.480 1.500 1.260 0.630 0.350 0.800 with AS*T1705...

SPARE PARTS
Designation Clamping screw Lubricant Center bolt Center bolt 1 Center bolt 2 Wrench
(Optional parts) (Optional parts) (Optional parts)
TPS17200... CSPB-4S M-1000 (C0.375X1.125H) - - IP-15D
TPS17300... CSPB-4S M-1000 - (C0.500X1.375H) - IP-15D
TPS17400... CSPB-4S M-1000 - - (TMBA0.750H) IP-15D

E PS17
S q u a re s h o u l d e r e n d m i l l s w i t h A S M T / A S GT 1 7 i n s e r t s

A.R. = +9°~ +17° ,R.R. = -20°~ -7°

R R R

øDs
øDc

ap
90˚ Lf Rs
L
Right hand (R) shown.

Inch Max. ap øDc z øDs ℓs Lf L Air hole Insert

EPS17100RSU 0.630 1.000 2 1.000 1.380 0.054 3.740 with AS*T1705...
EPS17100RSU-3/4 0.630 1.000 2 0.750 1.380 0.054 3.740 with AS*T1705...
EPS17125RSBU 0.630 1.250 2 1.250 1.380 0.054 3.740 with AS*T1705...
EPS17150RSBU 0.630 1.500 2 1.250 1.380 0.054 3.740 with AS*T1705...
EPS17100RLU 0.630 1.000 2 1.250 2.750 0.108 8.500 with AS*T1705...
EPS17125RLU 0.630 1.250 3 1.250 3.000 0.118 10.000 with AS*T1705...
EPS17150RLU 0.630 1.500 2 1.250 2.000 0.079 10.000 with AS*T1705...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EPS17... CSPB-4S M-1000 IP-15D

Reference pages
Inserts → D090, Standard cutting conditions → D091

Tungaloy D089
 INSERT
A S M T17-M J AS M T 1 7 -M S
A T A T

B
B
rε rε

A S GT17-A J
A T
Shoulder Milling

rε

P Steel   
M Stainless 
K Cast iron  
N Non-ferrous  
S Superalloys  : First choice
H Hard materials : Second choice
Coated
DS1100 Un-
Cermet coated

Max.

KS05F
AH130
AH140
AH120

NS740
T1115
T3130

Designation rε ap A B T

ASMT170504PDPR-MJ 0.016 0.630 z z z z z 0.665 0.385 0.220

ASMT170508PDPR-MJ 0.031 0.630 z z z z z z 0.665 0.385 0.220
ASMT170512PDPR-MJ 0.047 0.630 z z z 0.665 0.385 0.220
ASMT170516PDPR-MJ 0.062 0.630 z z z 0.665 0.385 0.220
ASMT170520PDPR-MJ 0.078 0.630 z 0.665 0.385 0.220
ASMT170530PDPR-MJ 0.118 0.630 z 0.665 0.385 0.220
ASMT170532PDPR-MJ 0.126 0.630 z z z 0.665 0.385 0.220
ASMT170508PDPR-MS 0.031 0.630 z z 0.665 0.385 0.220
ASGT170504PDFR-AJ 0.016 0.630 z z 0.665 0.385 0.220
ASGT170508PDFR-AJ 0.031 0.630 z z 0.665 0.385 0.220

z: Line up

CAUTION A RY POINT IN MODIF Y ING CUT TER BODIES

R
When using inserts with corner radius Corner radius rε (in) The dimension of modifying (in)
rε * 0.078", standard cutter bodies 0.016" ~ 0.062" Unnecessary
have to be modified “R”.
0.078" ~ 0.126" 0.078

D090 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Cutting speed Vc (sfm) Feed per tooth fz (ipt)
ISO Workpiece material Grade Chip-
breaker Cutter dia. Cutter dia. Cutter dia. Cutter dia. Cutter dia. Cutter dia.
ø0.472 ø0.630, ø0.787 > ø0.984 ø0.472 ø0.630, ø0.787 > ø0.984
0.002 ~ 0.002 ~ 0.002 ~
NS740 MJ 260 ~ 330 330 ~ 400 330 ~ 500
Mild steel, Low Carbon steels 0.003 0.005 0.006
(1018, 8620, etc.) < 180HB 0.002 ~ 0.005 ~ 0.005 ~
AH120 MJ 260 ~ 330 330 ~ 500 330 ~ 500
0.004 0.007 0.007

0.002 ~ 0.002 ~ 0.002 ~

NS740 MJ 260 ~ 330 260 ~ 330 260 ~ 400
Carbon steels, Alloy steels 0.003 0.003 0.004
(1045, 1055, etc.) < 300HB 0.002 ~ 0.004 ~ 0.004 ~
T3130 MJ 260 ~ 330 260 ~ 400 330 ~ 650

Shoulder Milling
0.004 0.006 0.007

0.002 ~ 0.004 ~ 0.005 ~

Die steels (SKD11, SKD61, etc.) < 300HB T3130 MJ 260 ~ 330 260 ~ 400 330 ~ 500
0.004 0.006 0.007

0.002 ~ 0.005 ~ 0.005 ~

Stainless steels (304, 316, etc.) < 250HB AH130 MS 260 ~ 330 330 ~ 500 330 ~ 650
0.004 0.006 0.007

Grey Cast irons, Ductile Cast irons etc. 0.003 ~ 0.005 ~ 0.006 ~
T1115 MJ 260 ~ 330 330 ~ 500 330 ~ 650
(CLASS 25-40, 65-45-12, etc.) 0.005 0.007 0.010

0.002 ~ 0.002 ~ 0.002 ~

Aluminum alloys (Si < 13%) DS1100 AJ 980 ~ 3300 300 ~ 1000 300 ~ 1000
0.008 0.008 0.008

0.002 ~ 0.002 ~ 0.002 ~

Aluminum alloys (Si ≥ 13%) DS1100 AJ 330 ~ 650 330 ~ 650 330 ~ 650
0.008 0.008 0.008

0.002 ~ 0.002 ~ 0.002 ~

Copper alloys KS05F AJ 650 ~ 1650 650 ~ 1650 650 ~ 1650
0.008 0.008 0.008

Notes: • When using at L/D * 4, machining at the lower feed rate.

• This TAC mill is not designed to cope with the centrifugal force and
dynamic balance at high speeds over 1000 m/min.
Therefore, the cutting speed in the outer diameter of the mill should
not exceed 3300 sfm.

A PPLICATION R A NGE
Helical feed Drilling flattened
drilling blind hole Enlarging
Shoulder
milling Grooving Ramping Plunging

Traversing
θ°
A
ap

øD1, 2 øD3 E

Max. depth Max. ramping Max. Min. machining Max. machining Hole dia. in drilling Max. cutting width
plunging
of cut angle depth hole dia. hole dia. (Blind hole) in enlarging hole

Inch Tool ø ap (in) θº A øD1 øD2 øD3 E

EPS17100... 1.000 0.642 5º 0.039 1.260 1.890 1.810 ~ 1.890 0.945

EPS17125... 1.250 0.640 3.5º 0.039 1.810 2.440 2.360 ~ 2.440 1.220

EPS17150... 1.500 0.640 2.5º 0.039 2.440 3.070 2.990 ~ 3.070 1.540

TPS17200RBU 2.000 0.634 1.5º 0.039 3.230 3.860 3.780 ~ 3.850 1.930

TPS17300RBU 3.000 0.630 0.7º 0.039 5.590 6.220 6.140 ~ 6.220 3.110

TPS17400RBU 4.000 0.630 0.05º 0.039 7.170 7.800 7.720 ~ 7.800 3.900

Notes : Corner tε for dimensions of øD1, øD2, and øD3: rε = 0.031"

Tungaloy D091
 TS E 4000R I AU
S q u a re s h o u l d e r m i l l s w i t h w e d g e c l a m p e d h i g h - p o s i t r i a n g l e i n s e r t s

A.R. = +17°, R.R. = +5°

ød
a

0.701"
R

Lf
øDc
Shoulder Milling

90˚ Right hand (R) shown.

Inch Max. ap øDc z Lf ød ℓ a b lb

TSE4003RIAU 0.394 3.150 4 1.970 1.000 1.020 0.375 0.236 2.20
TSE4004RIAU 0.394 4.000 6 2.480 1.500 1.260 0.500 0.394 4.19
TSE4005RIAU 0.394 4.920 6 2.480 1.500 1.500 0.625 0.394 6.39
TSE4006RIAU 0.394 6.300 8 2.480 2.000 1.500 0.750 0.433 10.80
TSE4008RIA 0.394 7.870 10 2.480 2.500 1.500 1.000 0.551 16.31
TSE4010RIA 0.394 9.840 12 2.480 2.500 1.500 1.000 0.551 30.42
TSE4012RIA 0.394 12.400 14 2.480 2.500 1.500 1.000 0.551 48.72

SPARE PARTS
Designation qLocator wWedge eWedge fixing screw rLocator fixing screw Wrench
TSE4003 - 4004... LE403R WF330N FDS-8S CM4X0.7X14 TP-4
TSE4005 - 4012... LE405R WF500R FDS-8S CM4X0.7X14 TP-4
q

w
r
e

INSERT
TE C N /TEEN 43Z T EC N 4 3 Z F R -D I A T E KR 2 2 -M S
rε 4.6

bs
90
°

20°

20°
ød

ød
bs
bs

20° T
ød T
T
P Steel     
M Stainless 
K Cast iron  
N Non-ferrous  
S Superalloys  : First choice
H Hard materials : Second choice
Coated Cermet Uncoated PCD

rε Max.
GH330
AH120
AH130
AH140
AH330

NS740

DX140
T3130

Designation ød T bs
T1115

UX30
TH10
N308

ap

TECN43ZFR 0.039 0.394 z 0.500 0.187 0.079

TECN43ZTR 0.039 0.394 z z 0.500 0.187 0.052
TEEN43ZFR 0.039 0.394 z 0.500 0.187 0.079
TEEN43ZTR 0.039 0.394 z z z z z z z z z z 0.500 0.187 0.052
TECN43ZFR-DIA - 0.138 z 0.500 0.187 0.079
TEKR2204PEPR-MS - 0.394 z 0.500 0.187 0.071
Note: T-DIA is trade name for Tungaloy’s PCD grade. Available in one-corner type z: Line up
DX140 : Packing Quantity = 1 pc.

Reference pages
Standard cutting conditions → D093

D092 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Roughing Finishing
(Depth of cut ap: > 0.59") (Depth of cut ap: 0.012" ~ 0.028")
ISO Workpiece materials Grades
Cutting speed Feed per tooth Cutting speed Feed per tooth
vc (sfm) f z (ipt) vc (sfm) f z (ipt)
AH330 425 - 1200 0.004 - 0.008 150 - 400 0.004 - 0.009

Mild steels AH120, GH330 425 - 750 0.004 - 0.008 500 - 800 0.004 - 0.009

Unhardened steels T3130 425 - 980 0.004 - 0.009 590 - 980 0.004 - 0.010
(< 180 HB) NS740, N308 425 - 650 0.004 - 0.007 500 - 800 0.004 - 0.008

UX30, AH140 330 - 590 0.004 - 0.008 425 - 650 0.004 - 0.009

AH330 330 - 900 0.004 - 0.007 150 - 320 0.004 - 0.008

Shoulder Milling
AH120, GH330 330 - 590 0.004 - 0.008 500 - 650 0.004 - 0.008
Carbon steels
T3130 425 - 900 0.004 - 0.008 425 - 650 0.004 - 0.009
Alloy steels
AH140 260 - 425 0.004 - 0.007 330 - 650 0.004 - 0.007
(< 300 HB)
NS740, N308 330 - 500 0.004 - 0.006 500 - 650 0.004 - 0.007

UX30 260 - 425 0.004 - 0.007 330 - 500 0.004 - 0.008

AH330 330 - 800 0.004 - 0.006 330 - 800 0.004 - 0.008

Die steels
T3130, AH120, GH330 330 - 500 0.004 - 0.006 330 - 500 0.004 - 0.008
(< 30 HRC)
UX30 260 - 425 0.004 - 0.006 260 - 425 0.004 - 0.008

Stainless steels AH130, AH140 260 - 590 0.004 - 0.008 330 - 650 0.004 - 0.010
(< 9.84 HB) AH120 500 - 650 0.004 - 0.007 650 - 820 0.004 - 0.010

Cast irons T1115 330 - 650 0.004 - 0.008 330 - 650 0.004 - 0.010
Ductile cast irons TH10 260 - 425 0.004 - 0.008 260 - 425 0.004 - 0.010

Aluminum alloys TH10 650 - 3300 0.002 - 0.010 350 - 1000 0.004 - 0.010
(Si < 13%) DX140 650 - 3300 0.002 - 0.006 350 - 1000 0.004 - 0.008

Copper alloys TH10 650 - 1650 0.004 - 0.006 650 - 1650 0.004 - 0.008

Note: Dry cutting is recommended for all materials except for aluminum alloys.
Maximum depth of cut for TECN43ZFR-DIA is 0.138".
When wet machining mild steels, carbon steels and alloy steels, use T3130 at lower cutting conditions.

Tungaloy D093
 TSP 4000R I A - U
S q u a re s h o u l d e r m i l l s w i t h w e d g e c l a m p e d 1 1 ° re l i e f t r i a n g l e i n s e r t s

A.R. = +5°, R.R. = 0°

ød
a

0.701"
R

Lf
øDc
Shoulder Milling

90˚ Right hand (R) shown.

Inch Max. ap øDc z Lf ød ℓ a b lb

TSP4003RIA-U 0.394 3.150 4 1.970 1.000 1.020 0.375 0.236 2.43
TSP4004RIA-U 0.394 4.000 6 2.480 1.500 1.260 0.625 0.394 4.41
TSP4005RIA-U 0.394 4.920 6 2.480 1.500 1.500 0.625 0.394 6.83
TSP4006RIA-U 0.394 6.300 8 2.480 2.000 1.500 0.750 0.433 11.24
TSP4008RIA-U 0.394 7.870 10 2.480 2.500 1.500 1.000 0.551 16.98
TSP4010RIA 0.394 9.840 12 2.480 2.500 1.500 1.000 0.551 31.08
TSP4012RIA 0.394 12.400 14 2.480 2.500 1.500 1.000 0.551 49.82

SPARE PARTS
Designation qLocator wWedge eWedge fixing screw rLocator fixing screw Wrench
TSP4003 - 4004... LP403R WF330N FDS-8S CM4X0.7X14 TP-4
TSP4005 - 4012... LP405R WF500R FDS-8S CM4X0.7X14 TP-4

q
w
r
e

Reference pages
Inserts, Standard cutting conditions → D095

D094 www.tungaloyamerica.com
 INSERT
T P C N /TP E N /TP K N 43Z T P K R / T PM R -M J

bs bs
90°
90°
11°
11°
ød T rε T
ød

P Steel     


Shoulder Milling
M Stainless
K Cast iron  
N Non-ferrous 
S Superalloys  : First choice
H Hard materials : Second choice
Coated Cermet Uncoated

rε Max.

GH330
AH120
AH130
AH140

NS740
T1115
T3130
Designation ød A T bs

UX30
N308

TH10
ap

TPCN43ZFR - 0.394 z 0.500 - 0.187 0.079

TPCN43ZTR - 0.394 z z z 0.500 - 0.187 0.079
TPEN43ZTR - 0.394 z 0.500 - 0.187 0.079
TPEN43ZTRCR - 0.394 z 0.500 - 0.187 0.079
TPKN43ZFR - 0.394 z 0.500 - 0.187 0.079
TPKN43ZTR - 0.394 z z z z z z z z z 0.500 - 0.187 0.079
TPKR43ZSR-MJ - 0.394 z z 0.500 - 0.187 0.059
TPMR2204PDSR-MJ 0.031 0.394 z z 0.500 - 0.187 0.047

z: Line up

STA NDA RD CUT TING CONDITIONS

Roughing Finishing
(Depth of cut ap: > 1.500") (Depth of cut ap: 0.012" - 0.028")
ISO Workpiece materials Grades
Cutting speed Feed per tooth Cutting speed Feed per tooth
vc (sfm) f z (ipt) vc (sfm) f z (ipt)
AH120, GH330 330 - 800 0.004 - 0.010 425 - 820 0.004 - 0.010
Mild steels
T3130 425 - 980 0.004 - 0.011 590 - 980 0.004 - 0.012
Unhardened steels
UX30 330 - 590 0.004 - 0.010 425 - 650 0.004 - 0.012
(< 180 HB)
NS740, N308 425 - 650 0.004 - 0.008 500 - 800 0.004 - 0.010
AH120, GH330 330 - 590 0.004 - 0.008 500 - 650 0.004 - 0.011
Carbon steels
T3130 425 - 650 0.004 - 0.010 425 - 650 0.004 - 0.011
Alloy steels
UX30 260 - 425 0.004 - 0.008 330 - 500 0.004 - 0.011
(< 300 HB)
NS740, N308 330 - 500 0.004 - 0.007 500 - 650 0.004 - 0.009

Die steels T3130, AH120, GH330 330 - 500 0.004 - 0.007 330 - 500 0.004 - 0.008
(< 30 HRC) UX30 260 - 425 0.004 - 0.007 260 - 425 0.004 - 0.008

Stainless steels AH130, AH140 500 - 650 0.006 - 0.009 650 - 750 0.006 - 0.010
(< 9.84 HB) AH120 500 - 750 0.006 - 0.008 650 - 820 0.006 - 0.009

Cast irons T1115 330 - 650 0.004 - 0.008 330 - 650 0.004 - 0.010
Ductile cast irons TH10, UX30 260 - 425 0.004 - 0.008 260 - 425 0.004 - 0.010

Standard cutting conditions for Metal-Jack (MJ) inserts TPM/KR

Feed per tooth fz (ipt)
ISO Workpiece materials (Roughing [Depth of cut: > 0.59"])
K: TPKR43ZSR-MJ M: TPMR2204PDSR-MJ
Mild steels·Unhardened steels
0.004 - 0.009 0.004 - 0.016
(< 180 HB)
Carbon steels · Alloy steels
0.004 - 0.008 0.004 - 0.014
(< 300 HB)

Die steels (< 30 HRC) 0.004 - 0.007 0.004 - 0.010

Notes: Dry cutting is recommended for above materials.

When wet machining mild steels, carbon steels and alloy steels, use T3130 at lower cutting conditions.

Tungaloy D095
MillLine - Face Milling
Inch Metric

D098
Face milling cutters with double-sided square, octagonal, and round inserts
ø2.000" - ø6.000"
45° max. ap 0.236"

D101
Face milling cutters with screw-on and wedge clamping systems
featuring 4 types of inserts for a broader application range
45° ø2.480" - ø12.402"
max. ap 0.295"

D10 6
Economical, double-sided inserts with 10 cutting edges for general-purpose milling
ø1.260" - ø6.299"
70° max. ap 0.252"

D10 9
Single-sided inserts with low cutting force for face milling
ø0.984" - ø6.299"
45° max. ap 0.197"

D114
Lightweight cutters with screw clamping system suitable for low-rigid machines
ø2.000" - ø4.000"
85° max. ap 0.315"

D117
Lightweight cutters in wedge clamping design with PCD inserts
ø80 - ø160 mm / ø63 mm
90° max. ap 8 mm

ISO Milling D12 0

45° - TMD4400, TMD5400

D096 www.tungaloyamerica.com
D oTr i p l e - M i l l

Tungaloy D097
 TASN 13
4 5 ° f a c e m i l l i n g c u t te r to s e a t d o u b l e s i d e d s q u a re , o c t a g o n a l , ro u n d i n s e r t
A.R.=+6.0°,R.R.=-6.8°~-6.3°
SNGU13 ONGU05 RNGU13
with square inserts with octagonal inserts with round inserts
øDb TASN13M160
ød

ℓ
a

Lf2

Lf3
Lf
45° 45°
øDc1 øDc2 øDc3
øDc1+0.551" øDc2+0.315" øDc3+0.480"
Right hand (R) shown.

Inch øDc1 øDc2 øDc3 z øDb Lf1 Lf2 Lf3 ød ℓ a b lb Air hole
TASN13U2.00B0.75R05 2.000 2.118 1.982 5 1.850 1.575 1.516 1.517 0.750 0.750 0.315 0.197 0.900 with
TASN13U2.50B0.75R06 2.500 2.618 2.482 6 1.850 1.575 1.516 1.517 0.750 0.750 0.315 0.197 1.320 with
TASN13U2.50B0.75R08 2.500 2.618 2.482 8 1.850 1.575 1.516 1.517 0.750 0.750 0.315 0.197 1.540 with
TASN13U3.00B1.00R08 3.000 3.118 2.982 8 1.969 1.969 1.909 1.911 1.000 1.024 0.374 0.236 1.980 with
Face Milling

TASN13U3.00B1.00R10 3.000 3.118 2.982 10 1.969 1.969 1.909 1.911 1.000 1.024 0.374 0.236 2.200 with
TASN13U4.00B1.50R08 4.000 4.118 3.982 8 3.150 1.969 1.909 1.911 1.500 1.276 0.626 0.394 3.750 with
TASN13U4.00B1.50R12 4.000 4.118 3.982 12 3.150 1.969 1.909 1.911 1.500 1.276 0.626 0.394 3.750 with
TASN13U5.00B1.50R10 5.000 5.118 4.982 10 3.150 2.480 2.421 2.422 1.500 1.378 0.626 0.394 5.950 with
TASN13U5.00B1.50R14 5.000 5.118 4.982 14 3.150 2.480 2.421 2.422 1.500 1.378 0.626 0.394 6.720 with
TASN13U6.00B2.00R12 6.000 6.118 5.982 12 3.937 2.480 2.421 2.422 2.000 1.496 0.748 0.433 8.600 without

SPARE PARTS
Designation Clamping screw Grip Lubricant Center bolt Center bolt 1 Torx bit
(Optional parts) (Optional parts)
TASN13… (øDc1 < 3.0") CSPB-4 H-TB2W M-1000 - (C0.375X1.125H) BLDIP15/S7
TASN13… (øDc1 = 3.0") CSPB-4 H-TB2W M-1000 - (C0.500X1.375H) BLDIP15/S7
TASN13… (øDc1 = 4.0") CSPB-4 H-TB2W M-1000 (TMBA-0.750H) - BLDIP15/S7
TASN13… (øDc1 = 5.0") CSPB-4 H-TB2W M-1000 (TMBA-0.750H) - BLDIP15/M7
TASN13… (øDc1 = 6.0") CSPB-4 H-TB2W M-1000 - - BLDIP15/M7

Reference pages
Inserts → D099, Standard cutting conditions → D100

D098 www.tungaloyamerica.com
 INSERT
S N M U -M J SNG U -M J S N G U -M H

ap

ap
ap
ød T ød T ød T

bs bs bs

A rε A rε A rε

S N G U -W ONM U -M J O N G U -M J

ap
ap
ap

T ød T ød T
ød

bs

A
rε rε

Face Milling
A bs bs
rε
O N G U -W RNM U -M J R N G U -M J
ap

ap

ap
ød T T T
ød

ød
A

rε rε

bs
bs rε
bs

S N G U #C -M J
ap

ap

ød T Corner details

bs
bs
A
P Steel 
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated
AH3135

rε Max.
AH120

T3225

Designation A ød T bs
T1215

ap

SNMU1307ANEN-MJ 0.020 0.236 z z z z 0.370 0.512 0.276 0.079

SNGU1307ANEN-MJ 0.020 0.236 z z z 0.370 0.512 0.276 0.079
SNGU1307ANEN-MH 0.031 0.236 z 0.354 0.512 0.276 0.079
SNGU1307ANEN-W 0.047 0.236 z z 0.378 0.512 0.276 0.295
ONMU0507ANEN-MJ 0.031 0.134 z z z z 0.193 0.512 0.276 0.028
ONGU0507ANEN-MJ 0.031 0.134 z z z 0.193 0.512 0.276 0.028
ONGU0507ANEN-W 0.063 0.134 z z 0.197 0.512 0.293 0.154
RNMU1307ZNER-MJ 0.236 0.236 z z z z - 0.512 0.280 0.039
RNGU1307ZNER-MJ 0.236 0.236 z z - 0.512 0.280 0.039
SNGU1307C14ANEN-MJ - 0.236 z z 0.343 0.512 0.276 0.055 z: Line up

Tungaloy D099
 STA NDA RD CUT TING CONDITIONS
S N M U / SN G U / ONM U / ONG U

ISO Workpiece materials Hardness Priority Grades Chip- Cutting speed Feed per tooth
breaker Vc (sfm) fz (ipt)
Low carbon steel First choice AH3135 MJ 330 - 980 0.004 - 0.020
200 - 300HB
(1015, 1020, etc.) For wear resistance T3225 MJ 660 - 1150 0.004 - 0.016

High carbon and alloy steel First choice AH3135 MJ 330 - 820 0.004 - 0.016
150 - 300HB
(1055, 4140, etc.) For wear resistance T3225 MJ 590 - 980 0.004 - 0.016

Prehardened steel First choice AH3135 MJ 330 - 660 0.004 - 0.016

30 - 40HRC
(NAK80, PX5, etc.) For wear resistance T3225 MJ 490 - 820 0.004 - 0.016

Stainless steel First choice AH3135 MJ 330 - 660 0.004 - 0.014

- 200HB
(304SS, 316SS, etc.) For wear resistance T3225 MJ 330 - 820 0.004 - 0.012

Stainless cast steel First choice T3225 MH 200 - 390 0.004 - 0.012
-
(1.4849, etc.) For low cutting force AH3135 MJ 200 - 390 0.004 - 0.012

Gray cast iron T1215 MJ 330 - 980 0.004 - 0.016

150 - 250 HB First choice
(Class 25, Class 30, etc.) AH120 MJ 330 - 820 0.004 - 0.020

Ductile cast iron T1215 MJ 330 - 980 0.004 - 0.016

150 - 250 HB First choice
(60-40-18, 80-55-06, etc.) AH120 MJ 260 - 660 0.004 - 0.020

Titanium alloys
Face Milling

- 40HRC First choice AH3135 MJ 100 - 200 0.004 - 0.012

(Ti-6AI-4V, etc.)

Heat-resistant alloys
- 40HRC First choice AH120 MJ 30 - 130 0.002 - 0.006
(Inconel718, etc.)

(H13, etc.) 40 - 50 HRC First choice AH3135 MJ 260 - 430 0.004 - 0.008
Hardened steel
(D2, etc.) 50 - 60 HRC First choice AH120 MJ 160 - 230 0.001 - 0.004

RNMU / RNGU

ISO Workpiece materials Hardness Priority Grades Chip- Cutting speed Feed per tooth
breaker Vc (sfm) fz (ipt)
Low carbon steel First choice AH3135 MJ 330 - 980
200 - 300 HB
(1015, 1020, etc.) For wear resistance T3225 MJ 660 - 1150
High carbon and alloy steel First choice AH3135 MJ 330 - 820 ※ap = 0.236": 0.004 - 0.012
150 - 300 HB ※ap = 0.078": 0.016 - 0.031
(1055, 4140, etc.) For wear resistance T3225 MJ 590 - 980 ※ap = 0.039": 0.031 - 0.059

Prehardened steel First choice AH3135 MJ 330 - 660

30 - 40 HRC
(NAK80, PX5, etc.) For wear resistance T3225 MJ 490 - 820
First choice AH3135 MJ 330 - 660 ※ap = 0.236": 0.004 - 0.010
Stainless steel
- 200 HB ※ap = 0.078": 0.012 - 0.027
(304SS, 316SS, etc.) For wear resistance T3225 MJ 330 - 820 ※ap = 0.039": 0.024 - 0.051
Stainless cast steel First choice T3225 MJ 200 - 390 ※ap = 0.078": 0.008 - 0.016
(1.4849, etc.) -
※ap = 0.039": 0.012 - 0.031
For fracture resistance AH3135 MJ 200 - 390
Gray cast iron AH120 MJ 330 - 980
150 - 250 HB First choice
(Class 25, Class 30, etc.) T1215 MJ 330 - 820 ※ap = 0.236": 0.004 - 0.012
※ap = 0.078": 0.016 - 0.031
Ductile cast iron AH120 MJ 330 - 980 ※ap = 0.039": 0.031 - 0.059
150 - 250 HB First choice
(60-40-18, 80-55-06, etc.) T1215 MJ 260 - 660

Titanium alloys
- 40 HRC First choice AH3135 MJ 100 - 200 ap = 0.039": 0.006 - 0.031
(Ti-6AI-4V, etc.)

Heat-resistant alloys
- 40 HRC First choice AH120 MJ 30 - 130 ap = 0.039": 0.002 - 0.012
(Inconel718, etc.)

(H13, etc.) 40 - 50 HRC First choice AH3135 MJ 260 - 430 ap = 0.039": 0.004 - 0.010
Hardened steel
(D2, etc.) 50 - 60 HRC First choice AH120 MJ 160 - 230 ap = 0.020": 0.001 - 0.004

※When using T3225 or T1215, decrease the feed per tooth (fz) to 80% of the abovementioned value.

D100 www.tungaloyamerica.com
TA N 07
4 5 ° s c re w c l a m p t y p e f a c e m i l l s w i t h d o u b l e s i d e d o c t a g o n a l o r s q u a re i n s e r t s
A.R.=-6°,R.R.=+15.5°

Double-sided Double-sided square inserts

octagonal inserts

Lf1

Lf2
ap
ap
44˚ 45˚

øDc1 øDc2
øDc1+ 0.5" øDc2+0.62"
Air Arbor
Inch øDc1 øDc2 z øDb Lf1 Lf2 ød ℓ a b Ib hole Insert type
TAN07R250U0075A05 2.500 2.394 5 1.750 1.750 1.805 0.750 0.750 0.313 0.188 1 with SN*U/ON*U/OWMT... A
TAN07R250U0075A06 2.500 2.394 6 1.750 1.750 1.805 0.750 0.750 0.313 0.188 1 with SN*U/ON*U/OWMT... A
TAN07R300U0100A06 3.000 2.894 6 2.000 2.000 2.055 1.000 0.750 0.375 0.219 2 with SN*U/ON*U/OWMT... A
TAN07R300U0100A08 3.000 2.894 8 2.000 2.000 2.055 1.000 0.750 0.375 0.219 2 with SN*U/ON*U/OWMT... A
TAN07R400U0150A07 4.000 3.894 7 2.400 2.000 2.055 1.500 1.000 0.625 0.375 3 with SN*U/ON*U/OWMT... A
TAN07R400U0150A10 4.000 3.894 10 2.400 2.000 2.055 1.500 1.000 0.625 0.375 3 with SN*U/ON*U/OWMT... A
TAN07R500U0150A08 5.000 4.894 8 2.400 2.500 2.555 1.500 1.000 0.625 0.375 5 with SN*U/ON*U/OWMT... B
TAN07R500U0150A12 5.000 4.894 12 2.400 2.500 2.555 1.500 1.000 0.625 0.375 5 with SN*U/ON*U/OWMT... B

Face Milling
TAN07R600U0200A10 6.000 5.894 10 4.000 2.500 2.555 2.000 1.000 0.750 0.438 7 without SN*U/ON*U/OWMT... B
TAN07R600U0200A15 6.000 5.894 15 4.000 2.500 2.555 2.000 1.000 0.750 0.438 7 without SN*U/ON*U/OWMT... B
TAN07R800U0250A12 8.000 7.894 12 5.300 2.500 2.555 2.500 1.400 1.000 0.531 13 without SN*U/ON*U/OWMT... C
TAN07R800U0250A18 8.000 7.894 18 5.300 2.500 2.555 2.500 1.400 1.000 0.531 13 without SN*U/ON*U/OWMT... C

Arbor type

Arbor type A Arbor type B Arbor type C

ø'b øDb
øG ød
øDb
D a ø4"
ød
a
R
R

b
E

b
R

ø0.669"

SPARE PARTS
Designation Clamping screw Grip Torx bit Center bolt Center bolt 1
(Optional parts) (Optional parts)
TAN07R250... SRM5X0.8IP20X+ACROLYTE H-TB BLDIP20/S7 - (C0.375X1.125H)
TAN07R300... SRM5X0.8IP20X+ACROLYTE H-TB BLDIP20/S7 - (C0.500X1.375H)
TAN07R400, 500... SRM5X0.8IP20X+ACROLYTE H-TB BLDIP20/S7 (TMBA-0.750H) -
TAN07R600, 800... SRM5X0.8IP20X+ACROLYTE H-TB BLDIP20/S7 - -

Reference pages
Inserts → D104, Standard cutting conditions → D105

Tungaloy D101
 Screw-on type
Cutter diameter OWMT-ML insert OWMT-HJ insert
and height with
single sided
octagonal insert

Lf3

Lf4
43˚ 15˚
-ML -HJ
øDc 4
øDc 3
øD 2-4
øD1-3 øD1-4

ap = 0.138" ap = 0.059"
(0.295", with double corner use)

Dimensions (in)
Inch
øDc3 øD1-3 øDc4 øD2-4 øD1-4 Lf3 Lf4
TAN07R250U0075A.. 2.520 2.213 3.000 2.665 3.028 1.789 1.805
TAN07R300U0100A.. 3.020 2.713 3.500 3.165 3.528 2.039 2.055
TAN07R400U0150A.. 4.020 3.713 4.500 4.165 4.528 2.039 2.055
Face Milling

TAN07R500U0150A.. 5.020 4.713 5.500 5.165 5.528 2.539 2.555

TAN07R600U0200A.. 6.020 5.713 6.500 6.165 6.528 2.539 2.555
TAN07R800U0250A.. 8.020 7.713 8.500 8.165 8.528 2.539 2.555
Note: OWMT08 inserts can be only used with screw on type cutters.

D102 www.tungaloyamerica.com
TA N 07-W
4 5 ˚ w e d g e c l a m p t y p e f a c e m i l l s w i t h d o u b l e s i d e d o c t a g o n a l o r s q u a re i n s e r t s .

Double-sided Double-sided square inserts

Lf1
octagonal inserts

Lf2
44˚ 45˚

øDc1 øDc2

ap

ap
øD1+ 0.5" øD2+ 0.62"
Arbor
Inch øDc1 øDc2 z øDb Lf1 Lf2 ød ℓ a b Ib Air hole Insert type
TAN07R250U0075A08W 2.500 2.394 8 1.750 1.750 1.805 0.750 0.750 0.313 0.188 1.60 without SN*U/ON*U/OWMT... B
TAN07R300U0100A10W 3.000 2.894 10 2.000 2.000 2.055 1.000 0.750 0.375 0.219 2.00 with SN*U/ON*U/OWMT... B
TAN07R400U0150A14W 4.000 3.894 14 2.400 2.000 2.055 1.500 1.000 0.625 0.375 2.80 without SN*U/ON*U/OWMT... B
TAN07R500U0150A18W 5.000 4.894 18 2.400 2.500 2.555 1.500 1.000 0.625 0.375 4.30 with SN*U/ON*U/OWMT... B
TAN07R600U0200A22W 6.000 5.894 22 4.000 2.500 2.555 2.000 1.000 0.750 0.438 6.80 without SN*U/ON*U/OWMT... B
TAN07R800U0250A28W 8.000 7.894 28 5.300 2.500 2.555 2.500 1.400 1.000 0.531 13.50 with SN*U/ON*U/OWMT... C

Face Milling
Arbor type
Arbor type B Arbor type C
øDb øDb
ød ø4"
a ød
a
R
b

b
R

ø0.669"

SPARE PARTS
Designation Grip Torx bit Wedge Clamping screw Center bolt
(Optional parts)
TAN07R250U0075A08W H-TBS BLDIP15/S7 CL ARM-10-TUNG1 DS-6P (C0.375X1.125H)
TAN07R300U - 800U**W H-TBS BLDIP15/S7 CL ARM-10-TUNG1 DS-6P -

Reference pages
Inserts → D104, Standard cutting conditions → D105

Tungaloy D103
 INSERT
ON M U /O N H U0705- M J / - M L O N H U 0 7 0 5 -W
ød T ød T

A rε bs

OW M T0807- HJ O W M T 0 8 0 7 -M L
ød ap2 T ød T

A
A rε bs rε
bs
ap
Face Milling

SN M U /S N H U1706 - M J / - M L S N H U 1 7 0 6 -W
øK T rε T

bs
ød
øK
A

rε A
B

P Steel  
M Stainless 
K Cast iron   
N Non-ferrous
S Superalloys   : First choice
H Hard materials : Second choice
Coated
AH3135

rε Max. bs Max.
AH725
AH130
AH120

AH140

Designation ød T B ød
T1215
T1115

ap ap2.

ONMU0705ANPN-MJ 0.031 0.187 z z z z z 0.283 0.244 - 0.681 - -

ONMU0705ANPN-ML 0.031 0.187 z z 0.283 0.244 - 0.681 - -
ONHU0705ANPN-MJ 0.031 0.187 z z 0.283 0.244 - 0.681 - -
ONHU0705ANTN-ML 0.031 0.187 z z z 0.283 0.244 - 0.681 - -
ONHU0705ANPR-W * - 0.187 z 0.283 0.228 - 0.689 0.252 -
OWMT0807ZNER-HJ 0.031 0.059 z - 0.291 - 0.748 0.039 0.295
OWMT0807AAER-ML 0.047 0.138 z z 0.205 0.291 - - 0.047 -
SNMU1706ANPR-MJ 0.031 0.295 z z z z 0.433 0.275 0.173 0.681 0.709 -
SNMU1706ANTR-ML 0.031 0.295 z z 0.433 0.275 0.173 0.681 0.709 -
SNHU1706ANPR-MJ 0.031 0.295 z z 0.433 0.275 0.173 0.681 0.709 -
SNHU1706ANTR-ML 0.031 0.295 z 0.433 0.275 0.173 0.681 0.709 -
SNHU1706ANFN-W * 0.016 0.295 z 0.681 0.256 - 0.681 0.433 -

* Pay attention to the wiper insert installation procedure below. z: Line up

Attention for wiper inserts

1 2 1 2
Attach only one wiper insert on the cutter and make sure Attach only one wiper insert on the cutter and make sure
the wiper edge faces the machining surface. the wiper edge faces the machining surface.
Feed rate: f < 0.217 ipr Feed rate: f < 0.374 ipr

D104 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Do ub l e-si ded i ns er t s
Recommendation Cutting speed Feed per tooth
ISO Workpiece material Hardness Priority
Grade Chipbreaker Vc (sfm) fz (ipt)
- 200 HB First choice AH3135 ML 330 - 980 0.008 - 0.020
Low carbon steel For wear
- 200 HB AH725 ML 330 - 980 0.008 - 0.020
1015, etc. resistance
For fracture
- 200 HB resistance AH140 MJ 260 - 590 0.008 - 0.020
200 - 300 HB First choice AH3135 MJ 230 - 750 0.008 - 0.016
High carbon steel For wear
200 - 300 HB AH725 MJ 230 - 750 0.008 - 0.016
1045, 1055, etc. resistance
For fracture
200 - 300 HB resistance AH140 MJ 260 - 590 0.008 - 0.016
150 - 330 HB First choice AH3135 MJ 330 - 660 0.008 - 0.016
Alloy steel For wear
150 - 330 HB resistance AH725 MJ 330 - 660 0.008 - 0.016
4140, etc.
150 - 330 HB For fracture AH140 MJ
resistance 260 - 490 0.008 - 0.016

Stainless steel
- 200 HB First choice AH3135 ML 100 - 150 0.004 - 0.012
S30400, etc.

150 - 250 HB First choice AH120 ML 330 - 820 0.004 - 0.020

Gray cast iron For fracture
150 - 250 HB resistance AH725 MJ 330 - 820 0.004 - 0.020
No.35B, No.45B, etc.

Face Milling
For wear
150 - 250 HB T1215 MJ 490 - 980 0.004 - 0.020
resistance
150 - 300HB First choice AH120 ML 260 - 660 0.004 - 0.016
Ductile cast iron For fracture
150 - 300 HB resistance AH725 MJ 260 - 660 0.004 - 0.016
60-40-18, etc.
150 - 300 HB For wear T1215 MJ 0.004 - 0.016
resistance 330 - 820
HRC 40 - 50 First choice AH3135 MJ 260 - 430 0.004 - 0.008
Hardened steel
HRC 50 - 60 First choice AH3135 MJ 160 - 230 0.002 - 0.004

Sin gl e-si ded i ns er t s

Cutting speed Feed per tooth: fz (ipt)
ISO Workpiece material Hardness Priority Grade Vc (sfm) ML HJ*
Low carbon steel - 200 First choice AH3135 330 - 980 0.004 - 0.020 0.02 - 0.079
1015, etc. - 200 For fracture AH130 -
resistance 330 - 980 0.004 - 0.020

High carbon steel 200 - 300 HB First choice AH3135 330 - 750 0.004 - 0.016 0.02 - 0.059
1045, 1055, etc. For fracture
200 - 300 HB AH130 330 - 750 0.004 - 0.016 -
resistance
Alloy steel 150 - 330 HB First choice AH3135 330 - 660 0.004- 0.016 0.02 - 0.059
4140, etc. 150 - 330 HB For fracture AH130 -
resistance 330 - 660 0.004- 0.016

Stainless steel - 200 HB First choice AH3135 330 - 500 0.004 - 0.010 0.012 - 0.02
S30400, etc. For fracture
- 200 HB AH130 330 - 500 0.004 - 0.010 -
resistance
Gray cast iron 150 - 250 HB First choice AH3135 330 - 830 0.004 - 0.020 0.02 - 0.079
No.35B, No.45B, etc. For fracture
150 - 250 HB AH130 330 - 830 0.004 - 0.020 -
resistance
Ductile cast iron 150 - 250 HB First choice AH3135 260 - 660 0.004 - 0.020 0.02 - 0.059
60-40-18, etc. 150 - 250 HB For fracture AH130 -
resistance 260 - 660 0.004 - 0.020

Titanium alloy - HRC 40 First choice AH3135 100 - 200 0.004 - 0.012 0.012 - 0.028
Ti-6Al-4V, etc. For fracture
- HRC 40 resistance AH130 100 - 200 0.004 - 0.012 -

Heat resistant alloy - HRC 40 First choice AH3135 30 - 130 0.002 - 0.006 0.004 - 0.012
Inconel718, etc. For fracture
- HRC 40 resistance AH130 30 - 130 0.002 - 0.006 -

HRC 40 - 50 First choice AH3135 260 - 420 - 0.004 - 0.012

Hardened steel
HRC 50 - 60 First choice AH3135 160 - 230 - 0.001 - 0.003
* Apply 20% of recommended feed when using HJ insert with ap over 0.591".

Tungaloy D105
 TE N 09R
70° face mills with double sided pentagonal inserts.
A.R.=-6°,R.R.=-10°~-2°
øDb
ød

b
a

R
Lf

ap
70°

øDc
øD1 Right hand (R) shown.

Inch Max. ap øDc z øD1 øDb Lf ød ℓ a b Ib Air hole Insert

TEN09R200U0075A03 0.252 2.000 3 2.240 1.690 1.570 0.750 0.750 0.310 0.200 0.300 with PN*U0905...
TEN09R200U0075A04 0.252 2.000 4 2.240 1.690 1.570 0.750 0.750 0.310 0.200 0.300 with PN*U0905...
TEN09R200U0075A06 0.252 2.000 6 2.240 1.690 1.570 0.750 0.750 0.310 0.200 0.300 with PN*U0905...
TEN09R250U0075A04 0.252 2.500 4 2.740 1.690 1.570 0.750 0.750 0.310 0.200 0.500 with PN*U0905...
TEN09R250U0075A06 0.252 2.500 6 2.740 1.690 1.570 0.750 0.750 0.310 0.200 0.500 with PN*U0905...
TEN09R250U0075A08 0.252 2.500 8 2.740 1.690 1.570 0.750 0.750 0.310 0.200 0.500 with PN*U0905...
TEN09R300U0100A04 0.252 3.000 4 3.240 1.970 1.970 1.000 1.020 0.370 0.240 0.900 with PN*U0905...
Face Milling

TEN09R300U0100A07 0.252 3.000 7 3.240 1.970 1.970 1.000 1.020 0.370 0.240 0.900 with PN*U0905...
TEN09R300U0100A10 0.252 3.000 10 3.240 1.970 1.970 1.000 1.020 0.370 0.240 0.900 with PN*U0905...
TEN09R400U0150A05 0.252 4.000 5 4.240 3.150 1.970 1.500 1.380 0.630 0.390 1.300 with PN*U0905...
TEN09R400U0150A08 0.252 4.000 8 4.240 3.150 1.970 1.500 1.380 0.630 0.390 1.300 with PN*U0905...
TEN09R400U0150A12 0.252 4.000 12 4.240 3.150 1.970 1.500 1.380 0.630 0.390 1.400 with PN*U0905...
TEN09R500U0150A06 0.252 5.000 6 5.240 3.150 2.480 1.500 1.460 0.630 0.390 2.600 with PN*U0905...
TEN09R500U0150A10 0.252 5.000 10 5.240 3.150 2.480 1.500 1.460 0.630 0.390 2.700 with PN*U0905...
TEN09R500U0150A16 0.252 5.000 16 5.240 3.150 2.480 1.500 1.460 0.630 0.390 2.900 with PN*U0905...
TEN09R600U0200A07 0.252 6.000 7 6.240 3.940 2.480 2.000 1.500 0.750 0.430 4.400 without PN*U0905...
TEN09R600U0200A12 0.252 6.000 12 6.240 3.940 2.480 2.000 1.500 0.750 0.430 4.600 without PN*U0905...
TEN09R600U0200A20 0.252 6.000 20 6.240 3.940 2.480 2.000 1.500 0.750 0.430 4.900 without PN*U0905...

SPARE PARTS
Designation Clamping screw Grip Lubricant Center bolt Center bolt 1 Torx bit
(Optional parts) (Optional parts)
TEN09R200, 250... CSTR-4L100 H-TBS M-1000 - (C0.375X1.125H) BT15S
TEN09R300... CSTR-4L100 H-TBS M-1000 - (C0.500X1.375H) BT15S
TEN09R400, 500... CSTR-4L100 H-TBS M-1000 (TMBA-0.750H) - BT15S
TEN09R600... CSTR-4L100 H-TBS M-1000 - - BT15M

Reference pages
Inserts → D107, Standard cutting conditions → D108

D106 www.tungaloyamerica.com
EEN 09
70° endmills with double sided pentagonal inserts.

A.R.=-6°,R.R.=-2°~-10°

øDs
øDc
øD1
ap
70˚
Lf Rs
L
Inch Max. ap øDc z øD1 øDs ℓs Lf L Ib Air hole Insert
EEN09R125U0125W03 0.252 1.250 3 1.250 1.250 2.280 1.500 3.780 0.700 with PN*U0905...
EEN09R150U0125W04 0.252 1.500 4 1.500 1.250 2.280 2.000 4.280 0.700 with PN*U0905...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EEN09... CSTR-4L100 M-1000 T-15D

Face Milling
INSERT
PN C U 0905-M J（Right-hand） P NCU0 9 0 5 -M L（Neutral-hand） PN C U 0 9 0 5 -AJ （Right-hand）
A T ød T A T
A

bs rε bs rε bs rε

PN M U 0905-M J（Neutral-hand） P NCU0 9 0 5 -W（Right-hand）

ød T ød T
A

bs rε bs rε

P Steel    
M Stainless 
K Cast iron   
N Non-ferrous 
S Superalloys   : First choice
H Hard materials : Second choice
Coated Un-
Cermet coated
AH3135

rε Max.
AH120
AH140
AH725

NS740
T1115
T1215
T3130

Designation A T ød bs
TH10

ap

PNCU0905GNER-MJ 0.031 0.252 z z z z z z 0.350 0.232 0.480 0.055

PNCU0905GNEN-ML 0.031 0.252 z 0.350 0.232 0.480 0.055
PNCU0905GNFR-AJ 0.031 0.252 z 0.350 0.248 0.480 0.055
PNMU0905GNEN-MJ 0.031 0.252 z z z 0.350 0.236 0.480 0.055
PNCU0905GNER-W 0.031 0.079 z - 0.236 0.480 0.150

z: Line up

Tungaloy D107
 STA NDA RD CUT TING CONDITIONS
Hardness Selection Recommended Chip- Cutting speed Feed per tooth
ISO Workpiece material
HB criteria grade breaker Vc (sfm) fz (ipt)
- 200 First choice AH3135, AH725 MJ 330 - 820 0.004 - 0.024

Low carbon steels - 200 Low cutting force AH3135 ML 330 - 820 0.004 - 0.020

1015 etc. Priority on wear

- 200 T3130 MJ 390 - 820 0.004 - 0.024
resistance
Priority on surface
- 200 NS740 MJ 330 - 820 0.004 - 0.020
quality
200 - 300 First choice AH3135, AH725 MJ 330 - 760 0.004 - 0.020

High carbon steels 200 - 300 Low cutting force AH3135 ML 330 - 760 0.004 - 0.016

1045 etc. Priority on wear

200 - 300 T3130 MJ 390 - 820 0.004 - 0.020
resistance
Priority on surface
200 - 300 NS740 MJ 330 - 820 0.004 - 0.016
quality
150 - 300 First choice AH3135, AH725 MJ 330 - 760 0.004 - 0.020

Alloyed steels 150 - 300 Low cutting force AH3135 ML 330 - 760 0.004 - 0.016

4140 etc. Priority on wear

150 - 300 T3130 MJ 390 - 820 0.004 - 0.020
resistance
Priority on fracture
150 - 300 NS740 MJ 330 - 820 0.004 - 0.016
resistance
Face Milling

- 300 First choice AH3135, AH725 MJ 330 - 590 0.004 - 0.020

Tool steels
- 300 Low cutting force AH3135 ML 330 - 590 0.004 - 0.016
D2 etc.
Priority on wear
- 300 T3130 MJ 390 - 590 0.004 - 0.020
resistance

Stainless steels - First choice AH3135 ML 300 - 590 0.004 - 0.016

S30400 etc. Priority on fracture

- AH3135, AH140 MJ 300 - 590 0.004 - 0.018
resistance

Gray cast irons - First choice AH120 MJ 460 - 820 0.004 - 0.024

No.250B, No.300B etc. Priority on wear

- T1215 MJ 490 - 280 0.004 - 0.024
resistance
- First choice AH120 MJ 330 - 660 0.004 - 0.024
Ductile cast irons
60-40-18 etc. Priority on wear
- T1215 MJ 390 - 720 0.004 - 0.024
resistance
Aluminum alloys Si < 13% - First choice TH10 AJ 1640 - 4921 0.004 - 0.020

Aluminum alloys Si ≥ 13% - First choice TH10 AJ 490 - 1640 0.004 - 0.020

- First choice AH3135 ML 98 - 197 0.004 - 0.016

Titanium alloys
Ti-6Al-4V, etc. Priority on fracture
- AH3135 MJ 98 - 197 0.004 - 0.016
resistance
Heat-resistance alloys
- First choice AH725 MJ 66 - 164 0.002 - 0.004
Inconel 718, etc.
· Remove excessive chip with an air blast to prevent chip jamming. · Cutting conditions may be limited depending on machine power, workpiece
· Use water-soluble coolant to avoid built-up edge in case extreme rigidity, and spindle output. When the cutting width, depth or overhang
welding occurs on cutting edges. (ex. aluminum machining). length is large, set Vc and fz to the lower recommended values and check
· For the operation with depth of cut which varies (ex. casting skin) and ma- the machine power and vibration.
chining of workpiece materials with interrupted surface, the feed (fz) should
be set to the lower recommended value shown in the above table.

Installation of the extra close pitch cutter inserts

 The extra close pitch cutter has a slanted screw.
 Locate insert and then fasten the screw. (Fig. A)
Locate insert
 Appropriate torque is 3.5 N·m. (2.58 lbf.ft) and then fasten
 After fastening the screw, please ensure there is no space the screw.
between the cutter body and insert. (Fig. B) Fig. A Fig. B

NOTES ON USE OF WIPER INSERT Mark

 To achieve a good surface finish, a wiper insert is recommended. Cutting

(PNCU0905GNER-W) edge
 When using the wiper insert, install the insert as shown in Fig. C.
Ensure that the groove is at the front as shown in Fig. D.
 The wiper insert has two wiping corners. (Fig. D)
 Do not use the other corners. It may break the tool body. Cutting
edge Groove
Fig. C Fig. D

D108 www.tungaloyamerica.com
TAW 13
30°~ 45° f a c e m i l l s w i t h s c re w c l a m p e d S W M T / S W GT 1 3 i n s e r t s

A.R.=+17°~+20°,R.R.=-16°~-11°
øDb
ød
a

b
R
Lf
45°
øDc

ap
øD1
Right hand (R) shown.

Inch øDc z øD1 øDb Lf ød ℓ a b Ib Air hole Insert

TAW13R200U0075A03 2.000 3 2.510 1.693 1.575 0.750 0.750 0.315 0.197 0.88 With SW*T13...
TAW13R200U0075A04 2.000 4 2.510 3.970 1.575 0.750 0.750 0.315 0.197 0.88 With SW*T13...
TAW13R200U0075A05 2.000 5 2.510 3.970 1.575 0.750 0.750 0.315 0.197 0.88 With SW*T13...
TAW13R300U0100A04 3.000 4 3.510 1.969 1.969 1.000 1.020 0.374 0.236 1.98 With SW*T13...
TAW13R300U0100A06 3.000 6 3.510 3.970 1.969 1.000 1.020 0.374 0.236 1.98 With SW*T13...
TAW13R300U0100A08 3.000 8 3.510 3.970 1.969 1.000 1.020 0.374 0.236 1.98 With SW*T13...

Face Milling
TAW13R400U0150A05 4.000 5 4.520 3.150 1.969 1.500 1.378 0.626 0.394 3.75 With SW*T13...
TAW13R400U0150A07 4.000 7 4.520 3.970 1.969 1.500 1.378 0.626 0.394 3.53 With SW*T13...
TAW13R400U0150A10 4.000 10 4.520 3.970 1.969 1.500 1.378 0.626 0.394 3.75 With SW*T13...
TAW13R500U0150A06 5.000 6 5.510 3.150 2.480 1.500 1.457 0.626 0.394 6.17 With SW*T13...
TAW13R500U0150A08 5.000 8 5.510 3.970 2.480 1.500 1.457 0.626 0.394 5.95 With SW*T13...
TAW13R500U0150A12 5.000 12 5.510 3.970 2.480 1.500 1.457 0.626 0.394 6.17 With SW*T13...
TAW13R600U0200A07 6.000 7 6.510 3.970 2.480 2.000 1.500 0.748 0.433 9.04 Without SW*T13...
TAW13R600U0200A10 6.000 10 6.510 3.970 2.480 2.000 1.500 0.748 0.433 8.60 Without SW*T13...
TAW13R600U0200A16 6.000 16 6.510 3.970 2.480 2.000 1.500 0.748 0.433 9.04 Without SW*T13...

SPARE PARTS
Designation eClamping screw Lubricant qShim screw
Center bolt Center bolt 1 wShim Wrench Wrench 1
(Optional parts) (Optional parts)
TAW13R200... CSPB-3.5 M-1000 DTS5-3.5SS - (C0.375X1.125H) FSSA1102 IP-15D P-3.5
TAW13R300... CSPB-3.5 M-1000 DTS5-3.5SS - (C0.500X1.375H) FSSA1102 IP-15D P-3.5
TAW13R400, 500... CSPB-3.5 M-1000 DTS5-3.5SS (TMBA-0.750H) - FSSA1102 IP-15D P-3.5
TAW13R600... CSPB-3.5 M-1000 DTS5-3.5SS - - FSSA1102 IP-15D P-3.5

wShim

qShim screw eClamping screw

Insert

Reference pages
Inserts → D111, Standard cutting conditions → D112 - D113

Tungaloy D109
 E AW 13
30°~ 45° e n d m i l l s w i t h s c re w c l a m p e d S W M T / S W GT 1 3 i n s e r t s

A.R.=+17°~+20°,R.R.=-16°~-11°

øDs
øDc
øD1
45°
Lf Rs
L Right hand (R) shown.

Metric øDc z øD1 øDs ℓs Lf L Kg Air hole Insert

EAW13R025M25.0-02 25 2 39 25 80 35 115 0.4 with SW*T13/WWCW13...
EAW13R032M32.0-02 32 2 46 32 80 35 115 0.7 with SW*T13/WWCW13...
EAW13R040M32.0-03 40 3 54 32 80 35 115 0.8 with SW*T13/WWCW13...
EAW13R050M32.0-03 50 3 63 32 80 40 120 1 with SW*T13/WWCW13...
EAW13R050M32.0-04 50 4 63 32 80 40 120 0.9 with SW*T13/WWCW13...
EAW13R063M32.0-04 63 4 76 32 80 40 120 1.1 with SW*T13/WWCW13...
EAW13R063M32.0-05 63 5 76 32 80 40 120 1.1 with SW*T13/WWCW13...
Face Milling

EAW13R080M32.0-04 80 4 94 32 80 40 120 1.5 with SW*T13/WWCW13...

EAW13R080M32.0-06 80 6 94 32 80 40 120 1.4 with SW*T13/WWCW13...

SPARE PARTS
Designation eClamping screw Lubricant qShim screw wShim Wrench Wrench 1
EAW13R025**~040** CSPB-3.5 M-1000 - - IP-15D -
EAW13R050**~080** CSPB-3.5 M-1000 DTS5-3.5SS FSSA1102 IP-15D P-3.5

wShim

qShim screw eClamping screw

Insert

Reference pages
Inserts → D111, Standard cutting conditions → D112 - D113

D110 www.tungaloyamerica.com
 INSERT
S W M T13T3-MJ S W M T 1 3 T 3 -M L

bs

bs
ød T ød T

θ˚ θ˚
rε rε
S W M W 13T3 ( Fl at ) S W M T 1 3 T 3 -H J
bs

bs
ød T ød T

θ˚ θ˚
rε rε
S W M T13T3-MS S W GT 1 3 T 3 -M J
bs

bs
ød T ød T

Face Milling
θ˚ θ˚
rε rε
S W GT13T3-AJ W W C W 1 3 T 3 AF E R -W S
T
bs

ød T rε

bs
ød

00
θ˚ θ˚

WW C W 13T3AF E/F R- WS W W C W 1 3 T 3 AF F R -W D R5
T T
rε
bs

bs
ød

ød
00

θ˚
00
R5

θ˚
R5

P Steel    
M Stainless 
K Cast iron  
N Non-ferrous   
S Superalloys   : First choice
H Hard materials : Second choice
Coated Un-
Cermet coated PCD
AH3135

DS1100

Max.
KS05F
AH120
AH130
AH140

GH110

NS740

DX140
T1115
T1215
T3130

Designation rε ap ød T θ˚ bs

SWMT13T3AFPR-MJ 0.059 0.157 z z z z z z z z 0.547 0.157 18.5 0.079

SWMT13T3AFER-ML 0.059 0.098 z z 0.547 0.157 18.5 0.079
SWMW13T3AFTR 0.059 0.197 z z z z z 0.547 0.157 18.5 0.079
SWMT13T3AFPR-HJ 0.059 0.079 z z z z z z 0.579 0.157 18.5 0.091
SWMT13T3AFPR-MS 0.039 0.157 z z z 0.555 0.157 18.5 0.079
SWGT13T3AFPR-MJ 0.059 0.157 z z 0.547 0.157 18.5 0.079
SWGT13T3AFFR-AJ - 0.157 z z 0.555 0.157 18.5 0.079
WWCW13T3AFER-WS 0.059 - z z 0.504 0.157 18.5 0.307
WWCW13T3AFFR-WS 0.059 - z z 0.504 0.157 18.5 0.307
WWCW13T3AFFR-WD - - z 0.504 0.157 18.5 0.307
z: Line up
DX140 : Packing Quantity = 1 pc.

Tungaloy D111
 STA NDA RD CUT TING CONDITIONS

Cutting Roughing (Depth of cut: > 0.394")

speed Feed per tooth: fz (ipt)
ISO Workpiece material Priority Grade vc (sfm) MJ ML HJ MS Flat AJ
AH3135 0.002 - 0.002 - 0.008 - 0.004 - 0.002 -
First choice 330 - 890 -
AH120 0.012 0.010 0.024 0.010 0.012
Mild and
low carbon steels Priority on wear 0.002 - 0.008 - 0.002 -
T3130 490 - 300 - - -
1010, 1015, etc. resistance 0.012 0.024 0.012
< 180 HB
Priority on surface 0.002 - 0.002 -
NS740 330 - 980 - - - -
quality 0.009 0.009
AH3135 0.002 - 0.002 - 0.008 - 0.002 -
First choice 330 - 760 - -
AH120 0.010 0.008 0.020 0.010
Carbon and
alloy steels Priority on wear 0.002 - 0.008 - 0.002 -
T3130 490 - 910 - - -
1045, 4140, etc. resistance 0.010 0.020 0.010
< 300 HB
Priority on surface 0.002 - 0.002 -
NS740 330 - 760 - - - -
quality 0.008 0.008
AH3135 0.002 - 0.002 - 0.008 - 0.002 -
Die steels First choice 330 - 590 - -
AH120 0.008 0.008 0.016 0.008
H13, D2, etc.
< 30 HRC Priority on wear 0.002 - 0.008 - 0.002 -
T3130 330 - 590 - - -
resistance 0.008 0.016 0.008
AH3135 0.004 - 0.008 - 0.004 -
Stainless steels First choice 260 - 660 - - -
AH130 0.010 0.020 0.008
S30400, S31600, etc.
< 250 HB Priority on wear 0.004 - 0.004 - 0.008 - 0.004 -
AH120 490 - 820 - -
Face Milling

resistance 0.010 0.008 0.020 0.010

0.002 - 0.008 - 0.002 -
First choice T1215 590 - 980 - - -
Gray cast irons 0.010 0.024 0.010
No.250B, No.300B, etc. Priority on impact 0.002 - 0.002 - 0.008 - 0.002 -
AH120 490 - 820 - -
resistance 0.010 0.008 0.024 0.010
0.002 - 0.008 - 0.002 -
First choice T1215 390 - 660 - - -
Ductile cast irons 0.010 0.024 0.010
60-40-18, 80-55-06, etc. Priority on impact 0.002 - 0.002 - 0.008 - 0.002 -
AH120 330 - 590 - -
resistance 0.010 0.008 0.024 0.010
Aluminum alloys DS1100 0.002 -
- 300 - 3281 - - - - -
Si < 13 % KS05F 0.008
Aluminum alloys DS1100 0.002 -
- 260 - 980 - - - - -
Si ≥ 13% KS05F 0.008
DS1100 0.002 -
Copper alloys - 660 - 1640 - - - - -
KS05F 0.008

Notes for use of HJ-type inserts

HJ-type inserts can be used for high feed machining.
When using the insert, care should be taken with the following:
• The maximum depth of cut is ap = 0.079". Select feeds within the above value.

0.079"
• Do not use the HJ-type inserts with other types (such as MJ- and MS-types) in
the same body.
• The outer shape of the HJ-type insert is different from those of other types (such
as MJ- and MS-types), but the insert can be held in the same insert pocket.

Face Cutting edge Main Cutting edge

Notes on use of wiper insert
• When requiring good surface finishes, use of a wiper insert • The wiper insert has one wiping corner.
(WWCW13T3AF_ R-W_ ) is recommended. In general, installing • The peripheral cutting edge of the wiper insert is retracted from
one wiper insert delivers superior surface finishes. the edge of the normal inserts. Therefore, the feed per tooth (ipt)
• When using the wiper insert, install the insert as shown in Fig. A. of the normal insert following the wiper insert is double that of
If the insert is installed as shown in Fig. B, breakage of the insert other inserts.
is inevitable and normal surface finish can not be obtained. • When using the wiper insert, depth of cut (ap) less than 0.039"
• The wiper insert must not be used together with HJ-type inserts is recommended.

Fig. A Fig. B

D112 www.tungaloyamerica.com
 Cutting Light cutting to finishing (Depth of cut: ≤ 0.394")
speed Feed per tooth: fz (ipt)
ISO Workpiece material Priority Grade vc (sfm) MJ ML HJ MS Flat AJ
AH3135 0.002 - 0.002 - 0.008 - 0.004 - 0.002 -
First choice 330 - 890 -
AH120 0.010 0.008 0.024 0.008 0.010
Mild and
low carbon steels Priority on wear 0.002 - 0.008 - 0.002 -
T3130 490 - 980 - - -
1010, 1015, etc. resistance 0.010 0.024 0.010
< 180 HB
Priority on surface 0.002 - 0.002 -
NS740 330 - 980 - - - -
quality 0.008 0.008
AH3135 0.002 - 0.002 - 0.008 - 0.002 -
First choice 330 - 760 - -
AH120 0.008 0.006 0.020 0.008
Carbon and
alloy steels Priority on wear 0.002 - 0.008 - 0.002 -
T3130 490 - 920 - - -
1045, 4140, etc. resistance 0.008 0.020 0.008
< 300 HB
Priority on surface 0.002 - 0.002 -
NS740 330 - 760 - - - -
quality 0.007 0.007
AH3135 0.002 - 0.002 - 0.008 - 0.002 -
Die steels First choice 330 - 1590 - -
AH120 0.007 0.005 0.016 0.007
H13, D2, etc.
< 30 HRC Priority on wear 0.002 - 0.008 - 0.002 -
T3130 330 - 590 - - -
resistance 0.007 0.016 0.007
AH3135 0.004 - 0.008 - 0.004 -
Stainless steels First choice 260 - 660 - - -
AH130 0.008 0.020 0.007
S30400, S31600, etc.
< 250 HB Priority on wear 0.004 - 0.004 - 0.008 - 0.004 -
AH120 590 - 820 - -

Face Milling
resistance 0.008 0.007 0.020 0.008
0.004 - 0.008 - 0.004 -
First choice T1215 590 - 980 - - -
Gray cast irons 0.008 0.024 0.008
No.250B, No.300B, etc. Priority on impact 0.004 - 0.002 - 0.008 - 0.004 -
AH120 490 - 820 - -
resistance 0.008 0.007 0.024 0.008
0.004 - 0.008 - 0.004 -
First choice T1215 390- 660 - - -
Ductile cast irons 0.008 0.024 0.008
60-40-18, 80-55-06, etc. Priority on impact 0.004 - 0.002 - 0.008 - 0.004 -
AH120 330 - 590 - -
resistance 0.008 0.007 0.024 0.008
Aluminum alloys DS1100 0.002 -
- 990 - 3281 - - - - -
Si < 13 % KS05F 0.008
Aluminum alloys DS1100 0.002 -
- 260 - 980 - - - - -
Si ≥ 13% KS05F 0.008
DS1100 0.002 -
Copper alloys - 660 - 1640 - - - - -
KS05F 0.008

Notes: stainless steel, use a water soluble cutting fluid. In this case, use the AH130
· When cutting at a large depth of cut or a large cutting width, the cutting grade at speeds lower than vc = 330 sfm.
speed (vc) and feed (fz) should be set to the lower side of the values shown · When wet machining mild steels, carbon steels and alloy steels, use T3130
in the above table. at lower cutting conditions.
· Dry cutting (or air-blowing) is generally recommended. However, when · TAW13 type TAC mills cannot be used for axial-feed cutting such as
chips tend to excessively adhere to the cutting edges when machining ramping, plunging and drilling.

Tungaloy D113
 TFE 12R U
8 6 ° f a c e m i l l s w i t h s c re w c l a m p e d i n s e r t s f o r a l u m i n u m m a c h i n i n g
A.R. = +13°, R.R. = +7°
øDb
ød
a

b
R
85˚30ߙ

Lf
ap
øDc Air through type

Inch Max. ap øDc z øDb Lf ød ℓ a b Ib Air hole Insert

TFE12300RU 0.315 3.000 4 1.970 1.380 1.000 0.964 0.375 0.236 0.88 with SEG*12X4...
TFE12400RU 0.315 4.000 6 1.970 1.380 1.000 0.964 0.375 0.236 1.34 with SEG*12X4...

Metric Max. ap øDc z øDb Lf ød ℓ a b Kg Air hole Insert

TFE12063R 8 63 3 45 35 22 19 10 6 0.34 with SEG*12X4...
TFE12125R 8 125 6 50 35 25.4 24.5 9.5 6 0.9 with SEG*12X4...
Face Milling

SPARE PARTS
Designation ① Clamping screw Lubricant Center bolt Center bolt 1 Wrench
TFE12300RU CSPB-4S M-1000 TMBA-0.500H - IP-15D
TFE12400RU CSPB-4S M-1000 TMBA-0.500H - IP-15D
TFE12063R CSPB-4S M-1000 - CM10X30H IP-15D
TFE12125R CSPB-4S M-1000 TMBA-M12H - IP-15D

Insert

qClamping
screw

E FE12R U
8 6 ° e n d m i l l s w i t h s c re w c l a m p e d i n s e r t s f o r a l u m i n u m m a c h i n i n g

A.R. = +13°, R.R. = +7°

L
Rs Lf
85˚30ߙ ap
øDb

øDc
øDsh6

Air through type

Inch Max. ap øDc z øDs øDb ℓs Lf L Ib Air hole Insert

EFE12200RU 0.315 2.000 3 0.750 1.180 2.362 1.375 3.406 0.77 with SEG*12X4...

SPARE PARTS
Designation ① Clamping screw Lubricant Wrench
EFE12200RU CSPB-4S M-1000 IP-15D

Insert

qClamping
screw

Reference pages
Inserts → D115, Standard cutting conditions → D116

D114 www.tungaloyamerica.com
 INSERT
S E G W 12X4ZEP R / ZEF R S E GT 1 2 X 4 -AJ
T T

bs

bs
B
B 20° 20°

A A

S E G W 12X4ZEF R- D S E G W 1 2 X 4 Z E F R -W D
T T

B
B

4.4

20° 20°
bs bs
A A

S E G W 12X4ZEF R- BD

Face Milling
T
B

20°
bs
A

P Steel  
M Stainless 
K Cast iron 
N Non-ferrous   
S Superalloys  : First choice
H Hard materials : Second choice
Coated Un-
Cermet coated PCD
DS1100

Max.
KS05F
AH120
AH140

NS740

DX140

Designation ap A B T bs

SEGW12X4ZEFR 0.315 z 0.500 0.500 0.157 0.071

SEGW12X4ZEPR 0.315 z z z 0.500 0.500 0.157 0.055
SEGT12X4ZEFR-AJ 0.315 z z 0.500 0.500 0.157 0.071
SEGW12X4ZEFR-D 0.138 z 0.500 0.500 0.157 0.071
SEGW12X4ZEFR-WD - z 0.488 0.504 0.157 0.079
SEGW12X4ZEFR-BD - z 0.488 0.516 0.157 0.071

z: Line up
DX140 : Package quantity = 1pc.

Tungaloy D115
 STA NDA RD CUT TING CONDITIONS
Cutting speed Feed per tooth
ISO Workpiece material Grade Designation
Vc (sfm) fz (ipt)

Carbon steels and alloy steels AH120 SEGW12X4ZEPR 330 ~ 590 0.001 ~ 0.006
(< 300HB) NS740 SEGW12X4ZEPR 330 ~ 590 0.001 ~ 0.006

Stainless steels (< 250HB) AH140 SEGW12X4ZEPR 260 ~ 590 0.001 ~ 0.006

Grey and ductile cast irons AH120 SEGW12X4ZEPR 330 ~ 650 0.001 ~ 0.006

Cast aluminum alloy / Die-cast KS05F SEGT12X4ZEFR-AJ 650 ~ 4900 0.001 ~ 0.008
(Si < 13%) DX140 SEGW12X4ZEFR-D 650 ~ 4900 0.001 ~ 0.008

Cast aluminum alloy / Die-cast KS05F SEGT12X4ZEFR-AJ 260 ~ 650 0.001 ~ 0.008
(Si ≥ 13%) DX140 SEGW12X4ZEFR-D 650 ~ 1650 0.001 ~ 0.008
Aluminum alloy KS05F SEGT12X4ZEFR-AJ 650 ~ 4900 0.001 ~ 0.008
(JIS 1000, 3000, 5000 and 6000 types)
Tensile strength < 350 N/mm2 DX140 SEGW12X4ZEFR-D 650 ~ 4900 0.001 ~ 0.008
Aluminum alloy KS05F SEGW12X4ZEFR 650 ~ 4900 0.001 ~ 0.008
(JIS 2000, 4000, and 7000 types)
Tensile strength > 350 N/mm2 DX140 SEGW12X4ZEFR-D 650 ~ 4900 0.001 ~ 0.008

KS05F SEGT12X4ZEFR-AJ 650 ~ 1640 0.001 ~ 0.008

Face Milling

Copper alloy
DX140 SEGW12X4ZEFR-D 650 ~ 1640 0.001 ~ 0.008

Notes:
• In milling aluminum and copper alloys: • When milling aluminum and copper alloys, use of a water soluble cutting
(1) For improved surface finish, use together with wiper insert fluid is recommended. When milling steels, cast irons, and stainless steels,
SEGW12X4ZEFR-WD dry cutting is recommended.
(2) For reducing burr occurrence, use together with deburring inserts
SEGW12X4ZEFR-BD • When the length-to-diameter overhang ratio of the tool (L/D) exceeds 3, re-
duce cutting speed and feed to 70 to 80% of the values given in the table.

D116 www.tungaloyamerica.com
DP D 09
L i g h t w e i g h t s q u a re m i l l s w i t h P C D i n s e r t s f o r a l u m i n u m m a c h i n i n g
A.R. = +8.5°, R.R. = +3° ~ +5°
øDb
ød
a

ap
R

Lf
øDc 90° Air through type

Metric Max. ap øDc z øDb Lf ød ℓ a b Kg Air hole Insert

DPD09080R 8 80 4 50 41 25.4 23 9.5 6 0.8 with YDEN0905...
DPD09080RB 8 80 6 50 41 25.4 28.5 9.5 6 0.82 with YDEN0905...
DPD09100R 8 100 6 50 35 25.4 24.5 9.5 6 1.13 with YDEN0905...
DPD09100RB 8 100 8 50 35 25.4 24.5 9.5 6 1.17 with YDEN0905...
DPD09125R 8 125 6 50 35 25.4 24.5 9.5 6 1.7 with YDEN0905...
DPD09125RB 8 125 10 50 35 25.4 24.5 9.5 6 1.77 with YDEN0905...
DPD09160R 8 160 8 60 52 31.75 40 12.7 8 3.28 with YDEN0905...

Face Milling
DPD09160RB 8 160 12 60 52 31.75 40 12.7 8 3.25 with YDEN0905...

SPARE PARTS
③ Adjusting
Designation ① Wedge ② Wedge fixing screw ④ Helisert Center bolt Center bolt 1 Wrench Wrench 1
screw
DPD09080R* FW-304R-T FDS-8ST-18 AJM5 LM5-0.8X1DNS - CM12X30H T-27T T-7F
DPD09100R* FW-304R-T FDS-8ST-18 AJM5 LM5-0.8X1DNS TMBA-M12H - T-27T T-7F
DPD09125R* FW-304R-T FDS-8ST-18 AJM5 LM5-0.8X1DNS TMBA-M12H - T-27T T-7F
DPD09160R* FW-304R-T FDS-8ST-18 AJM5 LM5-0.8X1DNS TMBA-M16H - T-27T T-7F

④ Helisert

③ Adjusting screw
Insert
② Wedge fixing screw
① Wedge

ED P D 09
L i g h t w e i g h t s q u a re e n d m i l l s w i t h P C D i n s e r t s f o r a l u m i n u m m a c h i n i n g

A.R. = +8.5°, R.R. = +3°

L
Rs Lf 90°
9
øDb

øDc
øDsh6

Air through type

Metric Max. ap øDc z øDs øDb ℓs Lf L Kg Air hole Insert

EDPD09063R 8 63 3 25 37 60 40 100 0.75 with YDEN0905...

SPARE PARTS
Designation ① Wedge ② Wedge fixing screw ③ Adjusting screw ④ Helisert Wrench Wrench 1
EDPD09063R FW-304R-T FDS-8SST AJM5 LM5-0.8X1DNS T-27T T-7F

④ Helisert

③ Adjusting screw
Insert
② Wedge fixing screw
① Wedge

Reference pages
Inserts → D118, Standard cutting conditions → D119

Tungaloy D117
 INSERT
YD EN 0905P DF R- D Y D E N 0 9 0 5 PD F R -W D
B T B T
9 R40 3
0

bs
2

A
A

YD EN 0905P DF R- BD
B T
R40 3
0 bs
A

P Steel
M Stainless
Face Milling

K Cast iron
N Non-ferrous 
S Superalloys : First choice
H Hard materials : Second choice
PCD

Max.
DX140

Designation ap A B T bs

YDEN0905PDFR-D 0.315 z 0.488 0.594 0.224 -

YDEN0905PDFR-WD - z 0.488 0.598 0.224 0.177
YDEN0905PDFR-BD - z 0.488 0.598 0.224 0.177
Note: As a principle, our company re-grinds these inserts. z: Line up
Package quantity = 1pc.

D118 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Cutting speed Feed per tooth
ISO Workpiece material Grade Designation
Vc (sfm) fz (ipt)
Aluminum alloy castings &
DX140 YDEN0905PDFR-D 500 ~ 4000 0.001 ~ 0.008
die castings Si < 13%

Aluminum alloy castings &

DX140 YDEN0905PDFR-D 650 ~ 1650 0.001 ~ 0.008
die castings Si ≥ 13%

Rolled aluminum alloys DX140 YDEN0905PDFR-D 1650 ~ 13000 0.001 ~ 0.008

Copper alloys DX140 YDEN0905PDFR-D 300 ~ 1650 0.001 ~ 0.008

Notes:
(1) When requiring improved surface finish, use the wiper insert together (4) Wet cutting, using a water soluble cutting fluid, is recommended.
with regular inserts YDEN0905PDFR-WD. (5) When the length-to-diameter overhang ratio of the tool (L/D) exceeds 3,
(2) When requiring reduced burr occurrence, use the deburring inserts reduce cutting speed and feed to 70 to 80% of the values given in the
together with regular inserts YDEN0905PDFR-BD. table.
(3) When using the cutter at speeds over 4920 SFM, use an arbor or tool-
holder balanced to within G16.

H OW TO PUT E AC H I N S E R T TOG E T H E R

Face Milling
For general Accuracy of machining surface Burr reduction priority
priority
General insert YDEN0905PDFR-D
Applicable insert

Wiper insert YDEN0905PDFR-WD - -

Wiper insert for burr reduction YDEN0905PDFR-BD - -
1 or 2 wiper inserts in General insert : Burr wiper
Number of Inserts by type All general
cutter body insert = 1 : 1

F : Height from cutting edge

F : Height from cutting edge

F : Height from cutting edge

General insert

General insert
General insert

R R
Specification of insert setting
0.002"

0.008"
Wiper insert Wiper insert for
burr reduction
øD : Cutter diameter
øD : Cutter diameter øD : Cutter diameter

Accuracy of machining surface (roughness and undulation)  

Burr of machining surface  

Tungaloy D119
 TM D 4400R I - U
4 5á f a c e m i l l s w i t h w e d g e c l a m p e d s q u a re i n s e r t s
A.R. = +15˚, R.R. = -3˚
ød
a

Lf
45°
øDc

0.268”
øD1 Right hand (R) shown.

Inch Max. ap øDc z øD1 Lf ød ℓ a b lb Insert

SD*N42.../SD*R1203.../
TMD4403RI-U 0.157 3.150 4 3.780 1.970 1.000 1.020 0.375 0.236 3.100
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4404RI-U 0.157 3.940 5 4.530 2.480 1.500 1.260 0.500 0.315 5.500
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4405RI-U 0.157 4.920 6 5.470 2.480 1.500 1.500 0.625 0.394 7.900
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4406RI-U 0.157 6.300 8 6.510 2.480 2.000 1.500 0.750 0.433 12.300
WDCN42ZFR-DIA
Face Milling

SD*N42.../SD*R1203.../
TMD4408RI-U 0.157 7.870 10 8.390 2.480 2.500 1.500 1.000 0.551 19.100
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4410RI-U 0.157 9.840 12 10.350 2.480 2.500 1.500 1.000 0.551 35.900
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4412RI-U 0.157 12.400 14 12.870 2.480 2.500 1.500 1.000 0.551 55.400
WDCN42ZFR-DIA

Arbor type

TMD4408/10RI-U TMD4412RI-U
øDb øDb
ø4" ø7"
ød ø4"
a ød
b
R

0.669"
ø0.699" M16 (For eye bolt)
ø0.866"

ø1.260" ø1.063"

SPARE PARTS
Designation ① Locator ④ Wedge fixing screw ② Locator fixing screw ③ Wedge Wrench
TMD44**RI-U LD440R FDS-8S CM4X0.7X14 WP440R TP-4

3 4

Reference pages
Inserts → D122, Standard cutting conditions → D123

D120 www.tungaloyamerica.com
T M D 4400R B -U
4 5 á f a c e m i l l s w i t h w e d g e c l a m p e d s q u a re i n s e r t s
A.R. = +15˚, R.R. = -3˚
ød
a

Lf
45°
øDc

0.268”
øD1 Right hand (R) shown.

Inch Max. ap øDc z øD1 Lf ød ℓ a b lb Insert

SD*N42.../SD*R1203.../
TMD4403RB-U 0.157 3.150 6 3.780 1.969 1.000 1.024 0.375 0.236 3.100
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4404RB-U 0.157 3.937 8 4.528 2.480 1.500 1.260 0.625 0.394 5.500
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4405RB-U 0.157 4.921 10 5.472 2.480 1.500 1.260 0.625 0.394 7.900
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4406RB-U 0.157 6.299 14 6.811 2.480 2.000 1.496 0.750 0.433 12.100
WDCN42ZFR-DIA

Face Milling
SD*N42.../SD*R1203.../
TMD4408RB-U 0.157 7.874 18 8.370 2.480 2.500 1.496 1.000 0.551 18.900
WDCN42ZFR-DIA
SD*N42.../SD*R1203.../
TMD4410RB-U 0.157 9.842 22 10.335 2.480 2.500 1.496 1.000 0.551 35.600
WDCN42ZFR-DIA

Arbor type

TMD04408/10RB-U
øDb
ø4"
ød
a
b
R

0.669"

SPARE PARTS
Designation ① Locator ④ Wedge fixing screw ② Locator fixing screw ③ Wedge Wrench
TMD44**RB-U LD440R FDS-8S CM4X0.7X14 WF310R TP-4

3 4

Reference pages
Inserts → D122, Standard cutting conditions → D123

Tungaloy D121
 INSERT
S D C N /S D E N /SDK N 42Z
General inserts Corner details
SD*N42Z*N SDKN42ZTN16 SD*N42ZTN20 SDKN42ZTNCR
SDEN42ZTNCR
bs

bs
bs

bs
θ° rε
45°
A T

SD C N 42ZFN - DIA
SDCN42ZFN-DIA
8”
11
0.
bs

SD K R 42Z -M J S D M R / S D KR 1 2 0 3 -M J
SDKR42ZSR-MJ Corner details SD*R1203AETN-MJ Corner details
Face Milling

(With 3-dimensional (With 3-dimensional

chipbreaker) SDMR1203AETN-MJ SDKR1203AETN-MJ
chipbreaker) rε1

bs
bs 0.020”
bs
bs

bs

rε1

0.020”
45°
A 45°
A

S D K R 42Z-MS W D C N 4 2 Z F R -D I A
SDKR42ZPN-MS Corner details Wiper inserts
WDCN42ZFR-DIA
bs
0.020”
bs bs
A
0.020”

B 45˚
45°
A
P Steel     
M Stainless 
K Cast iron   
N Non-ferrous  
S Superalloys  : First choice
H Hard materials : Second choice
Coated Cermet Uncoated PCD

Max.
GH330
AH120

AH140
AH330
AH130

NS740

DX140
FX105
T1115
T3130

Designation A B T θ˚ bs
UX30
N308

TH10

ap

SDCN42ZFN 0.157 z 0.500 - 0.125 15 0.047

SDCN42ZTN 0.157 z z z z 0.500 - 0.125 15 0.047
SDCN42ZTN20 0.157 z 0.500 - 0.125 15 0.079
SDEN42ZFN 0.157 z 0.500 - 0.125 15 0.047
SDEN42ZTN 0.157 z z z z z z z 0.500 - 0.125 15 0.047
SDEN42ZTNCR 0.157 z z z z 0.500 - 0.125 15 0.063
SDEN42ZTN20 0.157 z 0.500 - 0.125 15 0.079
SDKN42ZFN 0.157 z 0.500 - 0.125 15 0.047
SDKN42ZTN 0.157 z z z z z z z z z 0.500 - 0.125 15 0.047
SDKN42ZTNCR 0.157 z 0.500 - 0.125 15 0.063
SDKN42ZTN16 0.157 z 0.500 - 0.125 15 0.063
SDCN42ZFN-DIA 0.079 z 0.500 - 0.125 15 0.047
SDKR42ZSR-MJ 0.157 z z z z 0.500 - 0.125 15 0.063
SDMR1203AETN-MJ 0.157 z 0.500 - 0.125 15 0.063
SDKR1203AETN-MJ 0.157 z 0.500 - 0.125 15 0.063
SDKR42ZPN-MS 0.157 z z 0.500 - 0.125 15 0.063
WDCN42ZFR-DIA 0.020 z 0.480 0.616 0.125 15 0.193

z: Line up
D122 www.tungaloyamerica.com DX140 : Package quantity = 1pc.
 STA NDA RD CUT TING CONDITIONS
Roughing (Depth of cut: ap 0.059" ~ 0.157") Finishing (Depth of cut: ap 0.012" ~ 0.028")
ISO Workpiece material Grade
Cutting speed vc (sfm) Feed per tooth fz (ipt) Cutting speed vc (sfm) Feed per tooth fz (ipt)

NS740 492 ~ 820 0.004 ~ 0.008 492 ~ 820 0.004 ~ 0.010

AH330 492 ~ 1312 0.004 ~ 0.010 492 ~ 1312 0.004 ~ 0.011

Mild steels
Unhardened steels AH120 492 ~ 820 0.004 ~ 0.010 492 ~ 820 0.004 ~ 0.011
< 180 HB
T3130 492 ~ 984 0.004 ~ 0.011 591 ~ 984 0.004 ~ 0.012

AH130 ∙ AH140 328 ~ 591 0.004 ~ 0.011 427 ~ 656 0.004 ~ 0.012

T3130 492 ~ 919 0.004 ~ 0.010 591 ~ 919 0.004 ~ 0.011

NS740 ∙ N308 328 ~ 591 0.004 ~ 0.007 492 ~ 656 0.004 ~ 0.009
Carbon steels
Alloy steels AH330 328 ~ 1050 0.004 ~ 0.009 492 ~ 1050 0.004 ~ 0.010
< 300 HB
AH120 328 ~ 656 0.004 ~ 0.009 492 ~ 656 0.004 ~ 0.010

UX30 262 ~ 427 0.004 ~ 0.010 328 ~ 492 0.004 ~ 0.011

Face Milling
AH120 ∙ T3130 328 ~ 492 0.004 ~ 0.006 328 ~ 492 0.004 ~ 0.008
Die steels
< 30 HRC
AH330 328 ~ 820 0.004 ~ 0.006 328 ~ 820 0.004 ~ 0.008

AH130 ∙ AH140 262 ~ 591 0.006 ~ 0.010 328 ~ 656 0.006 ~ 0.011
Stainless steels
< 250 HB
AH120 ∙ GH330 492 ~ 755 0.006 ~ 0.009 656 ~ 820 0.006 ~ 0.010

T1115 328 ~ 656 0.004 ~ 0.008 328 ~ 656 0.004 ~ 0.010

Cast irons
Ductile cast irons
AH120 328 ~ 656 0.004 ~ 0.008 328 ~ 656 0.004 ~ 0.010

TH10 656 ~ 3281 0.002 ~ 0.008 1148 ~ 3281 0.004 ~ 0.012

Aluminum alloys
Si < 13%
DX140 656 ~ 3281 0.002 ~ 0.007 1148 ~ 3281 0.004 ~ 0.008

Copper alloy TH10 656 ~ 1640 0.004 ~ 0.008 656 ~ 1640 0.004 ~ 0.010

Note: • Dry cutting is recommended for all materials except for aluminum alloys.
• Maximum depth of cut for DX140 SDCN42ZFN-DIA is 0.080".
• When wet machining mild steels, carbon steels and alloy steels, use T3130 at lower cutting conditions.

Tungaloy D123
 TM D 5400I -U
4 5á f a c e m i l l s w i t h w e d g e c l a m p e d s q u a re i n s e r t s
A.R. = +15˚, R.R. = -3˚
ød
a

R
Lf
45˚

øDc

ap
øD1 Right hand (R) shown.

Inch Max. ap øDc z øD1 Lf ød ℓ a b lb Insert

TMD5404RI-U 0.236 3.940 4 4.650 2.480 1.500 1.260 0.625 0.394 5.510 SD*N53Z...
TMD5405RI-U 0.236 4.920 5 5.590 2.480 1.500 1.500 0.625 0.394 8.160 SD*N53Z...
TMD5406RI-U 0.236 6.300 5 6.930 2.480 2.000 1.500 0.750 0.433 12.790 SD*N53Z...
TMD5408RI-U 0.236 7.870 8 8.500 2.480 2.500 1.500 1.000 0.551 19.840 SD*N53Z...
TMD5410RI-U 0.236 9.840 10 10.430 2.480 2.500 1.500 1.000 0.551 35.930 SD*N53Z...
TMD5412RI-U 0.236 12.400 12 12.990 2.480 2.500 1.500 1.000 0.551 55.560 SD*N53Z...
Face Milling

Arbor type
TMD5410RI-U... TMD5412RI-U øDb
ø7"
øDb
ø4" ø4"
ød
ød
a
b
R

0.669" ø0.699" M16 for eye bolt

ø0.866"

ø1.260" ø1.063"

SPARE PARTS
Designation ① Locator ④ Wedge fixing screw ② Locator fixing screw ③ Wedge Wrench
TMD54**RI-U LD540R FDS-8S CM4X0.7X20 WF500R TP-4

3
4

Reference pages
Inserts, Standard cutting conditions → D125

D124 www.tungaloyamerica.com
 INSERT
S D C N /S D E N 53Z
SD*N53Z*N SDEN53ZTN20 SDKN53ZTN16 SDEN53ZTNCR SDKN53ZTNCR
Corner details Corner details Corner details Corner details
θ° bs
bs

bs

bs
bs
rε rε
A T
S D K R 53-M J
SDKR53ZSR-MJ
(With 3-dimensional chipbreaker)

bs
θ°
A T
P Steel    
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys  : First choice

Face Milling
H Hard materials : Second choice
Coated Cermet Uncoated

Max.
GH330
AH140
AH130
AH120

NS740
T3130

Designation A T θ˚ bs

UX30
N308

TH10
ap

SDCN53ZTN 0.236 z z 0.625 0.187 15 0.047

SDEN53ZFN 0.236 z 0.625 0.187 15 0.047
SDEN53ZTN 0.236 z z z 0.625 0.187 15 0.047
SDEN53ZTNCR 0.236 z 0.625 0.187 15 0.055
SDEN53ZTN20 0.236 z 0.625 0.187 15 0.079
SDKN53ZFN 0.236 z 0.625 0.187 15 0.047
SDKN53ZTN 0.236 z z z z z z z 0.625 0.187 15 0.047
SDKN53ZTNCR 0.236 z 0.625 0.187 15 0.063
SDKN53ZTN16 0.236 z 0.625 0.187 15 0.063
SDKR53ZSR-MJ 0.236 z z 0.625 0.187 15 0.079

z: Line up
STA NDA RD CUT TING CONDITIONS
Roughing (Depth of cut: ap 0.059" ~ 0.236") Finishing (Depth of cut: ap 0.012" ~ 0.028")
ISO Workpiece material Grade
Cutting speed vc (sfm) Feed per tooth fz (ipt) Cutting speed vc (sfm) Feed per tooth fz (ipt)

NS740 492 ~ 820 0.004 ~ 0.010 492 ~ 820 0.004 ~ 0.012

Mild steels AH120 492 ~ 820 0.004 ~ 0.014 492 ~ 820 0.004 ~ 0.014
Unhardened steels
< 180 HB T3130 492 ~ 984 0.004 ~ 0.014 591 ~ 984 0.004 ~ 0.014

AH130 328 ~ 591 0.004 ~ 0.014 427 ~ 656 0.004 ~ 0.014

T3130 492 ~ 919 0.004 ~ 0.014 591 ~ 919 0.004 ~ 0.014

Carbon steels
Alloy steels NS740 328 ~ 591 0.004 ~ 0.010 492 ~ 656 0.004 ~ 0.012
< 300 HB
AH120 328 ~ 656 0.004 ~ 0.012 492 ~ 656 0.004 ~ 0.014

Die steels < 30 HRC T3130 ∙ AH120 328 ~ 492 0.004 ~ 0.008 328 ~ 492 0.004 ~ 0.008

AH130 ∙ AH140 262 ~ 591 0.006 ~ 0.012 328 ~ 656 0.006 ~ 0.013
Stainless steels
< 250 HB
AH120 ∙ GH330 492 ~ 755 0.006 ~ 0.012 656 ~ 820 0.006 ~ 0.012

Cast irons, Ductile cast irons AH120 328 ~ 656 0.004 ~ 0.012 328 ~ 656 0.004 ~ 0.012

Aluminum alloys Si < 13% TH10 656 ~ 3281 0.002 ~ 0.012 1148 ~ 3281 0.004 ~ 0.012

Copper alloys TH10 656 ~ 1640 0.004 ~ 0.008 656 ~ 1640 0.004 ~ 0.010

Notes: • Dry cutting is recommended for all materials except for aluminum alloys.
• When wet machining mild steels, carbon steels and alloy steels, use T3130 at lower cutting conditions.

Tungaloy D125
MillLine - Slot Milling
Inch Metric

D12 8
Thin width slitting cutter with self-clamping insert
ø2.480" - ø4.921" (ø63 - ø125 mm),
Slot width 0.063" - 0.161" (1.6 - 4.1 mm)

D131
Slot milling cutters available in axial drive type working with 6-cornered tangentially
mounted inserts
ø3" - ø8" (ø80 - ø160 mm), Slot width 0.250" - 0.313" (4 - 5 mm)

D13 3
Axial and radial drive type slot milling cutters with 6-cornered radially mounted
inserts
ø3" - ø6", Slot width 0.375" - 0.625"

D13 6
Axial and radial drive type slot milling cutters for wider slots with tangentially
mounted inserts
ø3.937" - ø9.843", Slot width 0.630" - 0.984"

D126 www.tungaloyamerica.com
Tu n gT h i n - S l i t

Tungaloy D127
 S /ASG
Si d e c u t te r f o r t hi n sl i t t i ng and cut t i ng o f f

W b W
øD

ød
θ
Lf Lf øD5

øDc

øDb

øDc
ød

ae

ae
A type K type
Metric W min W max øDc z øDb ød øD5 Lf Max. ae θ° SS SS Drive flange type Insert
SSG01R063-E1.6 1.6 1.6 63 6 32 10 22 2.4 14 0 SW25-32 SW1.00-32 - K SSS16N
ASG01N076-1.6 1.6 1.6 76.2 8 39 25.4 - 2.4 14 112.5 - - - A SSS16N
ASG01N080-E1.6 1.6 1.6 80 8 39 22 - 2.4 16 112.5 - - - A SSS16N
ASG01N100-1.6 1.6 1.6 100 10 39 25.4 - 2.4 30 90 - - - A SSS16N
ASG01N100-E1.6 1.6 1.6 100 10 39 22 - 2.4 30 90 - - - A SSS16N
ASG01N125-1.6 1.6 1.6 125 12 64 31.75 - 2.4 30 75 - - - A SSS16N
ASG01N125-E1.6 1.6 1.6 125 12 64 27 - 2.4 30 75 - - - A SSS16N
SSG02R063-E2 1.85 2.5 63 6 32 10 22 2.4 15 0 SW25-32 SW1.00-32 - K SSM/S22N
ASG02N076-2 1.85 2.5 76.2 8 39 25.4 - 2.4 17 112.5 - - - A SSM/S22N
ASG02N080-E2 1.85 2.5 80 8 39 22 - 2.4 20 112.5 - - - A SSM/S22N
ASG02N100-2 1.85 2.5 100 10 39 25.4 - 2.4 30 90 - - - A SSM/S22N
ASG02N100-E2 1.85 2.5 100 10 39 22 - 2.4 30 90 - - - A SSM/S22N
ASG02N125-2 1.85 2.5 125 12 60 31.75 - 2.4 32 75 - - - A SSM/S22N
ASG02N125-E2 1.85 2.5 125 12 60 27 - 2.4 32 75 - - - A SSM/S22N
SSG03R063-E3 2.65 3.5 63 5 32 10 22 2.4 15 0 SW25-32 SW1.00-32 - K SSM/S31N
SSG03R080-3 2.65 3.5 80 6 46 25.4 36 2.4 16 0 SW32-25.4-46-J SW1.25-46 R1.00-46 K SSM/S31N
SSG03R080-E3 2.65 3.5 80 6 40(1) 22 32 2.4 19(2) 0 SW32-40 - R22-46 K SSM/S31N
Slot Milling

SSG03R100-3 2.65 3.5 100 6 46 25.4 36 2.4 26 0 SW32-25.4-46-J SW1.25-46 R1.00-46 K SSM/S31N
SSG03R100-E3 2.65 3.5 100 6 40(1) 22 32 2.4 29(3) 0 SW32-40 - R22-46 K SSM/S31N
SSG03R125-3 2.65 3.5 125 8 55 31.75 45 2.4 34 0 - - R1.25-55 K SSM/S31N
SSG03R125-E3 2.65 3.5 125 8 55 32 45 2.4 34 0 S32-55 - R32-55 K SSM/S31N
SSG04R063-E4 4 4.5 63 5 32 10 22 3.2 15 0 SW25-32 SW1.00-32 - K SSM/S41N
SSG04R080-4 4 4.5 80 6 46 25.4 36 3.2 16 0 SW32-25.4-46-J SW1.25-46 R1.00-46 K SSM/S41N
SSG04R080-E4 4 4.5 80 6 40(1) 22 32 3.2 19(2) 0 SW32-40 - R22-46 K SSM/S41N
SSG04R100-4 4 4.5 100 6 46 25.4 36 3.2 26 0 SW32-25.4-46-J SW1.25-46 R1.00-46 K SSM/S41N
SSG04R100-E4 4 4.5 100 6 40(1) 22 32 3.2 29(3) 0 SW32-40 - R22-46 K SSM/S41N
SSG04R125-4 4 4.5 125 8 55 31.75 45 3.2 34 0 - - R1.25-55 K SSM/S41N
SSG04R125-E4 4 4.5 125 8 55 32 45 3.2 34 0 S32-55 - R32-55 K SSM/S41N
(1) When using a drive flange, øD b = 46 mm
(2) When using a drive flange, Max. a e = 16 mm
(3) When using a drive flange, Max. a e = 26 mm

SPARE PARTS
Designation Grip Extractor
SSG01/02... ESG0.5 -
ASG01/02... ESG0.5 -
SSG03/04... - ESG1

Reference pages
Inserts, Standard cutting conditions → D129

D128 www.tungaloyamerica.com
 INSERT
SS M SSS
rε rε

W
W
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys : First choice
H Hard materials : Second choice
Coated

GH130
Designation rε W±0.002

SSM22N 0.008 z 0.087

SSM31N 0.008 z 0.122
SSM41N 0.010 z 0.161
SSS16N 0.006 z 0.063
SSS22N 0.008 z 0.087
SSS31N 0.008 z 0.122
SSS41N 0.010 z 0.161
z: Line up

STA NDA RD CUT TING CONDITIONS

Slot Milling
Hardness Cutting speed Chip thickness
ISO Work piece materials Insert
(HB) Vc (sfm) t (in)

Low carbon steel

- 200 SSM... 490 - 760 0.0020 - 0.006
(1015, etc.)

High carbon steel

200 - 300 SSM... 330 - 560 0.0016 - 0.005
(1045, etc.)

Alloy steel
150 - 300 SSM... 300 - 530 0.0016 - 0.005
(4140, etc.)

Tool steel
- 300 SSM... 230 - 390 0.0016 - 0.005
(D2, etc.)

Stainless steel
- SSS... 300 - 660 0.0016 - 0.005
(304, etc.)

Gray cast iron

150 - 250 SSM... 330 - 660 0.0020 - 0.006
(No250B, etc.)

Ductile cast iron

150 - 250 SSM... 260 - 430 0.0020 - 0.006
(65-45-12, etc.)

Tungaloy D129
 R ( dri ve f l ang e s et )
Dr i v e f l a n g e set f o r si d e cut ter s

H5

ød
5
øD

øD3

øD4
Inch ød øD3 øD4 øD5 H5
R1.00-46 1.000 1.811 0.197 1.417 0.394
R1.25-55 1.250 2.165 0.236 1.772 0.394

Metric ød øD3 øD4 øD5 H5

R22-46 22 46 6 32 10
R32-55 32 55 6 45 10

S W /S
Dr i v e s h a n k s f o r si d e cut ter s

L L

ød2
L1

øD3

øD5
øD5

øD3
øDs

ød2
ød
Slot Milling

SW*-* type S*-* type

Inch øDs ød ød2 øD3 øD5 L1 L
SW1.00-32 1.000 - 0.394 1.260 0.866 1.000 4.331
SW1.25-46 1.250 - 1.000 1.811 1.417 1.181 4.724
S1.25-55 - 1.250 1.250 2.165 1.772 - 2.362

Metric øDs ød ød2 øD3 øD5 L1 L

SW25-32 25 - 10 32 22 25 110
SW32-40 32 - 22 40 32 30 120
SW32-25.4-46-J 32 - 25.4 46 36 30 120
S32-55 - 32 32 55 45 - 60

SPARE PARTS
Wrench
Designation Screw
Mono block type Torx bit Handle
SW25-32 SR76-961 SETT-15/5 - -
SW32-40 SR76-963 SETT-15/5 - -
SW32-25.4-46-J SR76-963 SETT-15/5 - -
SW1.00-32 SR76-961 SETT-15/5 - -
SW1.25-46 SR76-963 SETT-15/5 - -
S1.25-55 SR76-943 - BT20M H-TB
S32-55 SR76-943 - BT20M H-TB

D130 www.tungaloyamerica.com
TUNG TSlit
h i n

AS V 02/03/04/ 05
A x i a l d r i v e t y p e s l o t m i l l i n g c u t te r w i t h t a n g e n t i a l l y m o u n te d i n s e r t s

a
Max.

Lf
øDb ae

W
θ

b
øDc
ød

Metric W øDc Edge/Z øDb ød Lf b a Max. ae θ° Insert

ASV02N080-4 4 80 5/10 41 25.4 6 28 6.35 15 162 TVKX0202...
ASV02N080-E4 4 80 5/10 41 27 6 29.8 7 15 162 TVKX0202...
ASV02N100-4 4 100 6/12 48 31.75 6 35.2 7.92 20 165 TVKX0202...
ASV02N100-E4 4 100 6/12 47 32 6 34.8 8 20 165 TVKX0202...
ASV02N125-4 4 125 8/16 58 38.1 6 42.3 9.52 30 168.75 TVKX0202...
ASV02N125-E4 4 125 8/16 55 40 6 43.5 10 30 168.75 TVKX0202...
ASV02N160-4 4 160 10/20 58 38.1 6 42.3 9.52 45 171 TVKX0202...
ASV02N160-E4 4 160 10/20 55 40 6 43.5 10 45 171 TVKX0202...
ASV03N080-5 5 80 5/10 41 25.4 6.5 28 6.35 15 162 TVKX03X3...
ASV03N080-E5 5 80 5/10 41 27 6.5 29.8 7 15 162 TVKX03X3...
ASV03N100-5 5 100 6/12 48 31.75 6.5 35.2 7.92 20 165 TVKX03X3...
ASV03N100-E5 5 100 6/12 47 32 6.5 34.8 8 20 165 TVKX03X3...
ASV03N125-5 5 125 8/16 58 38.1 6.5 42.3 9.52 30 168.75 TVKX03X3...
ASV03N125-E5 5 125 8/16 55 40 6.5 43.5 10 30 168.75 TVKX03X3...
ASV03N160-5 5 160 10/20 58 38.1 6.5 42.3 9.52 45 171 TVKX03X3...
ASV03N160-E5 5 160 10/20 55 40 6.5 43.5 10 45 171 TVKX03X3...

Slot Milling
SPARE PARTS
Designation Clamping screw Lubricant Wrench
ASV02/03N... SR114-018-L3.40 M-1000 T-6D

Inch W øDc Edge/Z øDb ød Lf b a Max. ae θ° Insert

ASV04N300-U025 0.250 3.000 4/8 1.614 1.000 0.394 1.102 0.250 0.595 157.5 TVKX04H3**
ASV04N400-U025 0.250 4.000 5/10 1.890 1.250 0.394 1.386 0.312 0.957 162 TVKX04H3**
ASV04N500-U025 0.250 5.000 6/12 2.283 1.500 0.394 1.665 0.375 1.260 165 TVKX04H3**
ASV04N600-U025 0.250 6.000 8/16 2.283 1.500 0.394 1.665 0.375 1.760 168.75 TVKX04H3**
ASV04N800-U025 0.250 8.000 10/20 2.717 2.000 0.394 2.197 0.500 2.543 171 TVKX04H3**
ASV05N300-U031 0.313 3.000 4/8 1.614 1.000 0.472 1.102 0.250 0.595 157.5 TVKX0504**
ASV05N400-U031 0.313 4.000 5/10 1.890 1.250 0.472 1.386 0.312 0.957 162 TVKX0504**
ASV05N500-U031 0.313 5.000 6/12 2.283 1.500 0.472 1.665 0.375 1.260 165 TVKX0504**
ASV05N600-U031 0.313 6.000 8/16 2.283 1.500 0.472 1.665 0.375 1.760 168.75 TVKX0504**
ASV05N800-U031 0.313 8.000 10/20 2.717 2.000 0.472 2.197 0.500 2.543 171 TVKX0504**

SPARE PARTS
Designation Clamping screw Torx bit Grip
ASV04N… SR14-500/L5.1 BT15S H-TBS
ASV05N… SR14-500-L7.0 BT15S H-TBS

Reference pages
Inserts, Standard cutting conditions → D132

Tungaloy D131
 INSERT
TV K X-M J
ød B
rε

P Steel  
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated

AH725
AH130
AH120
Designation rε B ød

TVKX04H304TN-MJ 0.016 z z z 0.138 0.665

TVKX04H308TN-MJ 0.031 z z z 0.138 0.665
TVKX050404TN-MJ 0.016 z z z 0.177 0.665
TVKX050408TN-MJ 0.031 z z z 0.177 0.665

z: Line up

STA NDA RD CUT TING CONDITIONS

Feed per edge line: fz (ipt)

Cutting
Hardness ASV ASV
Slot Milling

ISO Workpiece material Priority Grade speed

(HB) Vc ae / øDc (in) ae / øDc (in)
(sfm)
10% 20% 30% ≤ 50%
- 200 First choice AH725 300 - 590 0.0031 - 0.0098 0.0024 - 0.0075 0.0020 - 0.0063 0.0020 - 0.0059
Low carbon steel
(1015, etc.) - 200 For impact resistance AH130 300 - 590 0.0031 - 0.0098 0.0024 - 0.0075 0.0020 - 0.0063 0.0020 - 0.0059

200 - 300 First choice AH725 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051
High carbon steel
(1045, etc.) 200 - 300 For impact resistance AH130 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051

150 - 300 First choice AH725 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051
Alloy steel
(4140, etc.) 150 - 300 For impact resistance AH130 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051

- 300 First choice AH725 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051
Tool steel
(D2, etc.) - 300 For impact resistance AH130 300 - 590 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051

Stainless steel
- - AH130 300 - 660 0.0028 - 0.0087 0.0020 - 0.0063 0.0016 - 0.0055 0.0016 - 0.0051
(304, etc.)

Gray cast iron

150 - 250 - AH120 390 - 760 0.0031 - 0.0098 0.0024 - 0.0075 0.0020 - 0.0063 0.0020 - 0.0059
(No250B, etc.)

Ductile cast iron

150 - 250 - AH120 300 - 490 0.0031 - 0.0098 0.0024 - 0.0075 0.0020 - 0.0063 0.0020 - 0.0059
(65-45-12, etc.)

- First choice AH725 100 - 130 0.0028 - 0.0047 0.0020 - 0.0035 0.0016 - 0.0028 0.0016 - 0.0028
Titanium alloys
(Ti-6Al-4V, etc.) - For impact resistance AH130 100 - 130 0.0028 - 0.0047 0.0020 - 0.0035 0.0016 - 0.0028 0.0016 - 0.0028

- First choice AH725 70 - 120 0.0028 - 0.0047 0.0020 - 0.0035 0.0016 - 0.0028 0.0016 - 0.0028
Nickel-based alloys
(Inconel 718, etc.) - For impact resistance AH130 70 - 120 0.0028 - 0.0047 0.0020 - 0.0035 0.0016 - 0.0028 0.0016 - 0.0028

D132 www.tungaloyamerica.com
TUNGUSlot
niversal

AS W 06/07/09
Axi a l d r i v e t y p e s l o t m i l l i ng cut ter

a
Max.

Lf
øDb ae
θ

b
øDc
ød

Inch W øDc Edge/Z øDb ød Lf b a Max. ae θ° Insert

ASW06N300-U037 0.375 3.000 4/8 1.614 1.000 0.375 1.102 0.250 0.654 157.5° WNGU0603**
ASW06N400-U037 0.375 4.000 5/10 1.890 1.250 0.375 1.386 0.312 1.016 162° WNGU0603**
ASW06N500-U037 0.375 5.000 6/12 2.283 1.500 0.375 1.665 0.375 1.319 165° WNGU0603**
ASW06N600-U037 0.375 6.000 7/14 2.283 1.500 0.375 1.665 0.375 1.819 167.14° WNGU0603**
ASW07N400-U050 0.500 4.000 5/10 1.890 1.250 0.500 1.386 0.312 1.016 162° WNGU07T3**
ASW07N500-U050 0.500 5.000 6/12 2.283 1.500 0.500 1.665 0.375 1.319 165° WNGU07T3**
ASW07N600-U050 0.500 6.000 7/14 2.283 1.500 0.500 1.665 0.375 1.819 167.14° WNGU07T3**
ASW09N600-U062 0.625 6.000 7/14 2.283 1.500 0.625 1.665 0.375 1.819 167.14° WNGU0904**

SPARE PARTS
Designation Clamping screw Clamping screw 1 Grip Grip 1 Torx bit Wrench Lubricant
ASW06N… - CSPB-2.5 - - - IP-8D M-1000
ASW07N400… - CSPD-3 - SW6-SD BLD IP10/S7 - M-1000
ASW07N500… - CSPD-3 - SW6-SD BLD IP10/S7 - M-1000
ASW07N600… - CSPD-3 - - - IP-10D M-1000
ASW09N400… CSPB-3.5 - H-TBS - BLD IP15/S7 - M-1000

Slot Milling
ASW09N600… CSPB-3.5 - - - - IP-15D M-1000

Reference pages
Inserts → D134, Standard cutting conditions → D135

Tungaloy D133
 TUNGUSlot
niversal

TS W 06/07/09
Ra d i a l d r i v e t y p e sl o t m i l l i ng cut ter

øDb
ød

b
a
Max.
ae

Lf
øDc

Inch W øDc Edge/Z øDb ød Lf b a Max. ae Insert

TSW06R400-U037 0.375 4.000 5/10 1.969 1.000 1.969 0.236 0.374 0.976 WNGU0603...
TSW06R500-U037 0.375 5.000 6/12 2.756 1.250 1.969 0.315 0.500 1.083 WNGU0603...
TSW06R600-U037 0.375 6.000 7/14 3.937 1.500 2.480 0.394 0.626 0.992 WNGU0603...
TSW07R400-U050 0.500 4.000 5/10 1.969 1.000 1.969 0.236 0.374 0.976 WNGU07T3...
TSW07R500-U050 0.500 5.000 6/12 2.756 1.250 1.969 0.315 0.500 1.083 WNGU07T3...
TSW07R600-U050 0.500 6.000 7/14 3.937 1.500 2.480 0.394 0.626 0.992 WNGU07T3...
TSW09R600-U062 0.625 6.000 7/14 3.937 1.500 2.480 0.394 0.626 0.992 WNGU0904...

SPARE PARTS
Designation Clamping screw Clamping screw 1 Grip Lubricant Torx bit Wrench
TSW06R… - CSPB-2.5 - M-1000 - IP-8D
TSW07R400… - CSPD-3 SW6-SD M-1000 BLD IP10/S7 -
TSW07R500… - CSPD-3 SW6-SD M-1000 BLD IP10/S7 -
TSW07R600… - CSPD-3 - M-1000 - IP-10D
TSW09R… CSPB-3.5 - - M-1000 - IP-15D
Slot Milling

INSERT
W N G U -M J
T
A

rε ød
P Steel  
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated
AH725
AH130
AH120

Designation rε A ød T

WNGU060308TN-MJ 0.031 z z z 0.22 0.24 0.173

WNGU060316TN-MJ 0.063 z z z 0.22 0.24 0.173
WNGU07T308TN-MJ 0.031 z z z 0.268 0.291 0.217
WNGU07T316TN-MJ 0.063 z z z 0.268 0.291 0.217
WNGU090408TN-MJ 0.031 z z z 0.335 0.339 0.256
WNGU090416TN-MJ 0.063 z z z 0.335 0.339 0.256
z: Line up

Reference pages
Standard cutting conditions → D135

D134 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Feed per edge line: fz (ipt)
Cutting
Hardness speed TSW / ASW
ISO Workpiece material Priority Grade
(HB) Vc ae / øDc (in)
(sfm)
10% 20% 30% ≤ 50%

Low carbon steel - 200 First choice AH725 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079
(1015, etc.) - 200 For impact resistance AH130 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079

High carbon steel 200 - 300 First choice AH725 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079
(1045, etc.) 200 - 300 For impact resistance AH130 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079

Alloy steel 150 - 300 First choice AH725 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079
(4140, etc.) 150 - 300 For impact resistance AH130 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079

Tool steel - 300 First choice AH725 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079
(D2, etc.) - 300 For impact resistance AH130 300 - 590 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079

Stainless steel
- - AH130 300 - 660 0.0047 - 0.0130 0.0035 - 0.0098 0.0028 - 0.0083 0.0028 - 0.0079
(304, etc.)

Gray cast iron

150 - 250 - AH120 390 - 760 0.0047 - 0.0165 0.0035 - 0.0122 0.0028 - 0.0106 0.0028 - 0.0098
(No250B, etc.)

Ductile cast iron

150 - 250 - AH120 300 - 490 0.0047 - 0.0165 0.0035 - 0.0122 0.0028 - 0.0106 0.0028 - 0.0098
(65-45-12, etc.)

Titanium alloys - First choice AH725 100 - 130 0.0039 - 0.0067 0.0031 - 0.0051 0.0024 - 0.0043 0.0024 - 0.0039
(Ti-6Al-4V, etc.) - For impact resistance AH130 100 - 130 0.0039 - 0.0067 0.0031 - 0.0051 0.0024 - 0.0043 0.0024 - 0.0039

Nickel-based alloys - First choice AH725 70 - 120 0.0039 - 0.0067 0.0031 - 0.0051 0.0024 - 0.0043 0.0024 - 0.0039
(Inconel 718, etc.) - For impact resistance AH130 70 - 120 0.0039 - 0.0067 0.0031 - 0.0051 0.0024 - 0.0043 0.0024 - 0.0039

Slot Milling

Tungaloy D135
 TEC TSlot
a n g e n t i a l

ASN 10/12/1 5
A x i a l d r i v e t y p e s l o t m i l l i n g c u t te r w i t h t a n g e n t i a l l y m o u n te d i n s e r t s

b
a øD øDb

Lf
W
ød
θ°

b
ød øDc

Inch W øDc Z eff z øDb ød Lf b a Max. ae θ° Insert

ASN10R100M31.7-16-05 0.630 3.937 5 10 1.890 1.250 0.630 1.386 0.312 0.984 162 LMEU1008**ZNEN-MJ
ASN10R125M38.1-16-06 0.630 4.921 6 12 2.283 1.500 0.630 1.665 0.375 1.280 165 LMEU1008**ZNEN-MJ
ASN10R160M38.1-16-07 0.630 6.299 7 14 2.283 1.500 0.630 1.665 0.375 1.969 167.14 LMEU1008**ZNEN-MJ
ASN12R100M31.7-19-05 0.748 3.937 5 10 1.890 1.250 0.748 1.386 0.312 0.984 162 LMEU1208**ZNEN-MJ
ASN12R125M38.1-19-06 0.748 4.921 6 12 2.283 1.500 0.748 1.665 0.375 1.280 165 LMEU1208**ZNEN-MJ
ASN12R160M38.1-19-07 0.748 6.299 7 14 2.283 1.500 0.748 1.665 0.375 1.969 167.14 LMEU1208**ZNEN-MJ
ASN15R125M38.1-25-05 0.984 4.921 5 10 2.283 1.500 0.984 1.665 0.375 1.280 162 LMEU1509**ZNEN-MJ
ASN15R160M38.1-25-06 0.984 6.299 6 12 2.283 1.500 0.984 1.665 0.375 1.969 165 LMEU1206**ZNEN-MJ

SPARE PARTS
Designation Clamping screw Grip Torx bit
ASN10/12R... SM40-143-H0 H-TB BT15S
ASN15R... CSTB-5L159 H-TB BT20S
Slot Milling

Reference pages
Inserts, Standard cutting conditions → D138

D136 www.tungaloyamerica.com
TSN
R a d i a l d r i v e t y p e s l o t m i l l i n g c u t te r w i t h t a n g e n t i a l l y m o u n te d i n s e r t s

W
b

øDc

øDb
ød
ød3 ød3

a
Lf

Inch W øDc Z eff z øDb ød Lf b a Max. ae ød3 Insert

TSN10R100M25.4-16-05 0.630 3.937 5 10 1.969 1.000 1.969 0.236 0.374 0.945 - LMEU1008**ZNEN-MJ
TSN10R125M31.7-16-06 0.630 4.921 6 12 2.756 1.250 1.969 0.315 0.500 1.043 - LMEU1008**ZNEN-MJ
TSN10R160M38.1-16-07 0.630 6.299 7 14 3.937 1.500 2.480 0.394 0.626 1.142 - LMEU1008**ZNEN-MJ
TSN10R200M47.6-16-08 0.630 7.874 8 16 5.315 1.875 2.480 0.551 1.000 1.240 4.000 LMEU1008**ZNEN-MJ
TSN12R100M25.4-19-05 0.748 3.937 5 10 1.969 1.000 1.969 0.236 0.374 0.945 - LMEU1208**ZNEN-MJ
TSN12R125M31.7-19-06 0.748 4.921 6 12 2.756 1.250 1.969 0.315 0.500 1.043 - LMEU1208**ZNEN-MJ
TSN12R160M38.1-19-07 0.748 6.299 7 14 3.937 1.500 2.480 0.394 0.626 1.142 - LMEU1208**ZNEN-MJ
TSN12R200M47.6-19-08 0.748 7.874 8 16 5.315 1.875 2.480 0.551 1.000 1.240 4.000 LMEU1208**ZNEN-MJ
TSN12R250M47.6-19-09 0.748 9.843 9 18 5.512 1.875 2.480 0.551 1.000 2.126 4.000 LMEU1208**ZNEN-MJ
TSN15R125M31.7-25-05 0.984 4.921 5 10 2.756 1.250 1.969 0.315 0.500 1.043 - LMEU1509**ZNEN-MJ
TSN15R160M38.1-25-06 0.984 6.299 6 12 3.937 1.500 2.480 0.394 0.626 1.142 - LMEU1509**ZNEN-MJ
TSN15R200M50.8-25-07 0.984 7.874 7 14 5.315 2.000 2.480 0.551 1.000 1.240 4.000 LMEU1509**ZNEN-MJ
TSN15R250M63.5-25-08 0.984 9.843 8 16 5.512 2.500 2.480 0.551 1.000 2.126 4.000 LMEU1509**ZNEN-MJ

SPARE PARTS
Designation Clamping screw Grip Torx bit

Slot Milling
TSN10/12R... SM40-143-H0 H-TB BT15S
TSN15R... CSTB-5L159 H-TB BT20S

Reference pages
Inserts, Standard cutting conditions → D138

Tungaloy D137
 INSERT
LM E U -M J

A T

B
rε

P Steel  
M Stainless 
K Cast iron  
N Non-ferrous
S Superalloys   : First choice
H Hard materials : Second choice
Coated

AH725
AH120
AH140
Designation rε A B T

LMEU100808ZNEN-MJ 0.031 z z z 0.500 0.413 0.315

LMEU100816ZNEN-MJ 0.063 z z z 0.492 0.413 0.315
LMEU100824ZNEN-MJ 0.094 z z z 0.488 0.413 0.315
LMEU100832ZNEN-MJ 0.125 z z z 0.480 0.413 0.315
LMEU120808ZNEN-MJ 0.031 z z z 0.535 0.500 0.315
LMEU120816ZNEN-MJ 0.063 z z z 0.528 0.500 0.315
LMEU120824ZNEN-MJ 0.094 z z z 0.520 0.500 0.315
LMEU120832ZNEN-MJ 0.125 z z z 0.516 0.500 0.315
LMEU150908ZNEN-MJ 0.031 z z z 0.614 0.591 0.374
LMEU150916ZNEN-MJ 0.063 z z z 0.606 0.591 0.374
Slot Milling

LMEU150924ZNEN-MJ 0.094 z z z 0.602 0.591 0.374

LMEU150932ZNEN-MJ 0.125 z z z 0.594 0.591 0.374
z: Line up

STA NDA RD CUT TING CONDITIONS

Feed per edge line: fz (ipt)
Cutting
Hardness speed TSN / ASN
ISO Workpiece material Priority Grade
(HB) Vc ae / øDc (in)
(sfm)
10% 20% 30% ≤ 50%

Low carbon steel - 200 First choice AH725 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098
(1015, etc.) - 200 For impact resistance AH140 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098

200 - 300 First choice AH725 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098
High carbon steel
(1045, etc.) 200 - 300 For impact resistance AH140 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098

150 - 300 First choice AH725 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098
Alloy steel
(4140, etc.) 150 - 300 For impact resistance AH140 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098

Tool steel - 300 First choice AH725 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098
(D2, etc.) - 300 For impact resistance AH140 300 - 590 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098

Stainless steel
- - AH140 300 - 660 0.0087 - 0.0165 0.0063 - 0.0122 0.0055 - 0.0106 0.0051 - 0.0098
(304, etc.)

Gray cast iron

150 - 250 - AH120 390 - 760 0.0087 - 0.0200 0.0063 - 0.0150 0.0055 - 0.0126 0.0051 - 0.0118
(No250B, etc.)

Ductile cast iron

150 - 250 - AH120 300 - 490 0.0087 - 0.0130 0.0063 - 0.0098 0.0055 - 0.0083 0.0051 - 0.0079
(65-45-12, etc.)

Titanium alloys
- First choice AH725 100 - 130 0.0047 - 0.0087 0.0035 - 0.0063 0.0028 - 0.0055 0.0028 - 0.0051
(Ti-6Al-4V, etc.)

Nickel-based alloys
- First choice AH725 70 - 120 0.0047 - 0.0087 0.0035 - 0.0063 0.0028 - 0.0055 0.0028 - 0.0051
(Inconel 718, etc.)

D138 www.tungaloyamerica.com
MEMO

Slot Milling

Tungaloy D139
MillLine - Prof ile Milling

Inch Metric
D 016
Radius cutters with double-sided inserts with rigid clamping
ø1.000" - ø2.000"
max. ap 0.157"

D142
Indexable endmill for high-precision finishing with 2 effective cutting edges
ø0.375" - ø1.250"

D14 8
Double-sided positive inserts for finishing to semi-finishing in profiling operations
ø16.0 mm - ø25 mm
max. ap 0.039"

D15 0
Radius cutters with single-sided inserts for profile milling of complex parts
ø0.787" - ø2.598"
max. ap 0.315"

D15 5
Radius cutters featuring single-sided inserts with serrated cutting edges for anti-chatter
ø1.260" - ø4.921"
max. ap 0.315"

Other radius mills D15 9

T/ERD12/16, E/HWD

Single Effective Tools D16 4

- Ball Cutters
EBP, EBD, BBB

D140 www.tungaloyamerica.com
D oTw i s t- B a l l

Tungaloy D141
 EB FU
I n d ex a b l e e n d m i l l s f o r hi g h p reci si o n f i ni s h

øDs
øDs
øDc

øDc
R

R R
Rs L2
Lf α°
Lf Rs
L L
Fig. 1 Fig. 2

Inch Material øDc øDs ℓs Lf L L2 α° Air hole Fig Insert

EBFU037T050S0400 Steel 0.375 0.500 3.000 1.000 4.000 0.625 9.0° with 2 ZF*U037
EBFU037S037C0550 Carbide 0.375 0.375 2.500 3.000 5.500 - - without 1 ZF*U037
EBFU037T062S0600 Steel 0.375 0.625 3.500 2.500 6.000 0.625 3.5° with 2 ZF*U037
EBFU037S037C0875 Carbide 0.375 0.375 3.250 5.500 8.750 - - without 1 ZF*U037
EBFU050S050S0437 Steel 0.500 0.500 3.187 1.188 4.375 - - with 1 ZF*U050
EBFU050S050C0637 Carbide 0.500 0.500 2.750 3.625 6.375 - without 1 ZF*U050
EBFU050T062S0637 Steel 0.500 0.625 4.000 2.375 6.375 1.000 2.5° with 2 ZF*U050
EBFU050S050C0875 Carbide 0.500 0.500 2.750 6.000 8.750 - - without 1 ZF*U050
EBFU062T075S0500 Steel 0.625 0.750 3.000 2.000 5.000 0.563 2.0° with 2 ZF*U062
EBFU062S062C0637 Carbide 0.625 0.625 3.375 3.000 6.375 - - without 1 ZF*U062
EBFU062T075S0637 Steel 0.625 0.750 3.625 2.750 6.375 0.563 1.5° with 2 ZF*U062
EBFU062S062C0875 Carbide 0.625 0.625 2.750 6.000 8.750 - - without 1 ZF*U062
EBFU075T100S0700 Steel 0.750 1.000 4.000 3.000 7.000 1.563 4.5° with 2 ZF*U075
EBFU075S075C0875 Carbide 0.750 0.750 4.000 4.750 8.750 - - without 1 ZF*U075
EBFU075T100S0875 Steel 0.750 1.000 4.000 4.750 8.750 1.000 1.5° with 2 ZF*U075
EBFU075S075C1200 Carbide 0.750 0.750 3.250 8.750 12.000 - - without 1 ZF*U075
EBFU100T125S0800 Steel 1.000 1.250 4.000 4.000 8.000 1.250 2.5° with 2 ZF*U100
EBFU100S100C0875 Carbide 1.000 1.000 4.000 4.750 8.750 - - without 1 ZF*U100
EBFU100T125S1000 Steel 1.000 1.250 4.000 6.000 10.000 1.188 1.4° with 2 ZF*U100
EBFU100S100C1200 Carbide 1.000 1.000 3.250 8.750 12.000 - - without 1 ZF*U100
EBFU125S125S1000 Steel 1.250 1.250 6.000 4.000 10.000 - - with 1 ZF*U125
EBFU125S125C1200 Carbide 1.250 1.250 3.250 8.750 12.000 - - without 1 ZF*U125

SPARE PARTS
Designation Clamping screw Torx bit Grip Wrench
Profile Milling

EBFU037... TS30F100A - - T10D

EBFU050... TS40F120A - - T15D
EBFU062... TS50F160A - - T-T20
EBFU075... TS60F200A BLDT25/M7 SW6-T -
EBFU100... TS70F250A BLDT25/M7 SW6-T -
EBFU125... TS70F300A - - T-T30

Reference pages
Inserts → D144 - D145, Standard cutting conditions → D146

D142 www.tungaloyamerica.com
HB FM
I nd ex a b l e e n d m i l l s w i t h Tung Fl ex t hread co n n e c t i on f or h i gh p re c i s i on f i n i s h

A C Ts T
R

øD3
øDc
R R

Lf A A - A cross section
L6

Metric øDc L6 Lf C T øD3 Ts Air hole Insert

HBFM10M06 10 34.5 20 5 7 9.7 M6 with ZF*M100...
HBFM12M06 12 37.5 23 5 7 11.5 M6 with ZF*M120...
HBFM12M08 12 40 23 8 10 13 M8 with ZF*M120...
HBFM16M08 16 47 30 8 10 13 M8 with ZF*M160...
HBFM20M10 20 49 30 10 15 19 M10 with ZF*M200...
HBFM25M12 25 57 35 10 17 24 M12 with ZF*M250...
HBFM30M16 30 66 43 12 22 29 M16 with ZF*M300...
HBFM32M16 32 66 43 12 22 29.5 M16 with ZF*M320...
See page D147 for TungFlex modular shank.

SPARE PARTS
Designation Clamping screw Torx bit Grip Wrench
HBFM10... TS 30F100A - - T-10D
HBFM12... TS 40F120A - - T-15D
HBFM16... TS 50F160A BT20S H-TB2W -
HBFM20... TS 60F200A BLDT25/M7 H-TB2W -
HBFM25... TS 70F250A BLDT25/M7 H-TB2W -
HBFM30... TS 80F300A - - T-T30
HBFM32... TS 80F300A - - T-T30

Profile Milling

Reference pages
Inserts → D144 - D145, Standard cutting conditions → D146

Tungaloy D143
 INSERT
ZFB U -M J / ZF BM - M J Z F B U -M L
T T

A rε A rε

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys  : First choice
Inch H Hard materials  : Second choice
Coated

AH725
Designation rε A T

ZFBU037R00-MJ 0.188 z 0.375 0.114

ZFBU050R00-MJ 0.250 z 0.500 0.134
ZFBU062R00-MJ 0.313 z 0.625 0.173
ZFBU075R00-MJ 0.375 z 0.750 0.213
ZFBU062R00-MJ 0.313 z 0.625 0.173
ZFBU100R00-MJ 0.500 z 1.000 0.252
ZFBU075R00-MJ 0.375 z 0.750 0.213
ZFBU125R00-MJ 0.625 z 1.250 0.291
ZFBU037R00-ML 0.188 z 0.375 0.114
ZFBU050R00-ML 0.250 z 0.500 0.134
ZFBU062R00-ML 0.313 z 0.625 0.173
ZFBU075R00-ML 0.375 z 0.750 0.213
ZFBU100R00-ML 0.500 z 1.000 0.252
ZFBU125R00-ML 0.625 z 1.250 0.291
z: Line up
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys  : First choice
Profile Milling

Metric H Hard materials  : Second choice

Coated
AH725
AH710

Designation rε A T

ZFBM100R00-MJ 5 z z 10 2.9
ZFBM120R00-MJ 6 z z 12 3.4
ZFBM160R00-MJ 8 z z 16 4.4
ZFBM200R00-MJ 10 z z 20 5.4
ZFBM250R00-MJ 12.5 z z 25 6.4
ZFBM300R00-MJ 15 z z 30 7.4
ZFBM320R00-MJ 16 z z 32 7.4

z: Line up

D144 www.tungaloyamerica.com
ZFR U -M J / ZF RM - M J (Corner radius type)
3º T

A rε
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys  : First choice
Inch H Hard materials  : Second choice
Coated
AH725
Designation rε A T

ZFRU037R003-MJ 0.031 z 0.375 0.114

ZFRU050R003-MJ 0.031 z 0.500 0.134
ZFRU050R006-MJ 0.062 z 0.500 0.134
ZFRU050R012-MJ 0.125 z 0.500 0.134
ZFRU062R003-MJ 0.031 z 0.625 0.173
ZFRU062R006-MJ 0.062 z 0.625 0.173
ZFRU062R012-MJ 0.125 z 0.625 0.173
ZFRU075R003-MJ 0.031 z 0.750 0.213
ZFRU075R006-MJ 0.062 z 0.750 0.213
ZFRU075R012-MJ 0.125 z 0.750 0.213
ZFRU100R003-MJ 0.031 z 1.000 0.252
ZFRU100R006-MJ 0.062 z 1.000 0.252
ZFRU100R012-MJ 0.125 z 1.000 0.252
ZFRU125R003-MJ 0.031 z 1.250 0.291
ZFRU125R006-MJ 0.062 z 1.250 0.291
ZFRU125R012-MJ 0.125 z 1.250 0.291

z: Line up
P Steel 
M Stainless 
K Cast iron 

Profile Milling
N Non-ferrous 
Metric
S Superalloys  : First choice
H Hard materials  : Second choice
Coated
AH725
AH710

Designation rε A T

ZFRM120R05-MJ 0.5 z z 12 3.4

ZFRM120R10-MJ 1 z z 12 3.4
ZFRM160R05-MJ 0.5 z z 16 4.4
ZFRM160R10-MJ 1 z z 16 4.4
ZFRM160R15-MJ 1.5 z z 16 4.4
ZFRM200R10-MJ 1 z z 20 5.4
ZFRM200R15-MJ 1.5 z z 20 5.4

z: Line up

Tungaloy D145
 STA NDA RD CUT TING CONDITIONS
Recommended Cutting Feed per tooth: fz (ipt)
ISO Workpiece Hardness Grades Max. axial speed øDc (in)
materials Selection Chip- depth of cut
criteria breaker Vc (sfm) ø0.375 ø0.500 ø0.625 ø0.750 ø1.000 ø1.250

85 - 180 HB AH725 First choice MJ ≤0.04D 590 - 850 0.008 0.008 0.010 0.010 0.012 0.014
Low carbon steel,
alloy steel
85 - 180 HB AH725 For wear ML ≤0.04D 590 - 850 0.008 0.008 0.010 0.010 0.012 0.014
resistance

180 - 280 HB AH725 First choice MJ ≤0.03D 490 - 750 0.008 0.008 0.010 0.010 0.012 0.014
High carbon steel,
alloy steel
180 - 280 HB AH725 For wear ML ≤0.03D 490 - 750 0.008 0.008 0.010 0.010 0.012 0.014
resistance

HRC 40 - 48 AH725 First choice ML ≤0.03D 590 - 980 0.008 0.008 0.010 0.010 0.012 0.014
Prehardened steel
Die & mold tool
steel For impact
HRC 40 - 48 AH725 resistance MJ ≤0.03D 590 - 980 0.008 0.008 0.010 0.010 0.012 0.014

135 - 200 HB AH725 First choice ML ≤0.03D 330 - 820 0.006 0.008 0.008 0.010 0.010 0.012
Stainless steel
135 - 200 HB AH725 For impact MJ ≤0.03D 330 - 820 0.006 0.008 0.008 0.010 0.010 0.012
resistance

150 - 240 HB AH725 First choice MJ ≤0.04D 300 - 1150 0.008 0.010 0.012 0.012 0.014 0.016
Cast iron
For wear
150 - 240 HB AH725 resistance ML ≤0.04D 300 - 1150 0.008 0.010 0.012 0.012 0.014 0.016

- AH725 First choice ML ≤0.03D 660 - 1310 0.010 0.014 0.014 0.014 0.016 0.018
Aluminum
For impact
- AH725 resistance MJ ≤0.03D 660 - 1310 0.010 0.014 0.014 0.014 0.016 0.018

HRC 48 - 60 AH725 First choice ML ≤0.02D 330 - 720 0.003 0.004 0.005 0.006 0.008 0.010
High hardened
steel
For impact
HRC 48 - 60 AH725 MJ ≤0.02D 330 - 720 0.003 0.004 0.005 0.006 0.008 0.010
resistance

· Remove excessive chip accumulation with an air blast. · Cutting conditions maybe limited depending on machine power, workpiece
· For the operation with depth of cut which varies (ex.casting skin) and rigidity, and spindle output. When the cutting width, depth, or overhang
machining of workpiece materials with interrupted surface, the feed per tooth length is large, set Vc and fz to the lower recommended values and check the
(fz) should be set to the lower recommended value shown in the above table. machine power and vibration.
Profile Milling

How to clamp the insert

1. Clear chips and dust from the pocket.
2. Place the insert in the pocket. The insert can be placed only in one direction.
3. Tighten the screw while pressing the insert into the pocket.

How to check the run-out

1. Clamp the insert on the shank.
2. Clamp the shank on a high-precision arbor.
3. Measure the run-out on tool presetter or by dial gauge.

Notes:
1. Due to the helical cutting edge, it is important that the
run-out is inspected with the insert clamped on the shank.
2. Do not use micrometer or caliper to inspect the insert diameter as inaccurate dimensions may be provided.

D146 www.tungaloyamerica.com
Tu ngFl ex
Mo d u l a r s h a n k

øDs
ød
M
L1 Rs
L

Metric øDs L ℓs L1 ød M α° Shank type

SM06-L60C10 10 60 40 20 9.7 M6 0 Cylindrical
SM06-L105-C12 12 105 45 60 9.7 M6 1.2 Cylindrical
SM06-L125-C16 16 125 65 60 9.7 M6 3.3 Cylindrical
SM08-L73C16 16 73 48 25 13 M8 0 Cylindrical
SM08-L128-C16 16 128 48 80 13 M8 0.9 Cylindrical
SM08-L170-C20 20 170 103.2 66.8 13 M8 3.3 Cylindrical
SM10-L80-C20 20 80 50 30 18 M10 0 Cylindrical
SM10-L130-C20 20 130 50 80 18 M10 0.6 Cylindrical
SM10-L200-C25 25 200 142.8 57.2 19 M10 3.3 Cylindrical
SM12-L86-C25 25 86 56 30 21 M12 5.1 Cylindrical
SM12-L200-C32 32 200 122 78 21 M12 4.4 Cylindrical
SM16-L95-C32 32 95 60 35 29 M16 1.7 Cylindrical
SM16-L230-C32 32 230 180 50 29 M16 1.8 Cylindrical

Profile Milling

Tungaloy D147
 H FW X 04-M
Sm a l l -ra d i u s cut ter f o r f i ni shi ng o p erat i o n ; M od u l a r h e a d w i t h Tu n gF l ex t h re a d c on n e c t i on

A.R. = 0°, R.R. = -14°

L6
Lf R
C Ts T
A R R

øD3
øDc
4° A A - A cross section

Metric øDc z L6 Lf C T øD3 Ts Kg Air hole Insert

HFWX04M016M08R02 16 2 42 25 8 10 13 M8 0.03 with WXHU04...
HFWX04M020M10R03 20 3 49 30 10 15 18 M10 0.05 with WXHU04...
HFWX04M025M12R04 25 4 52 30 10 17 21 M12 0.09 with WXHU04...
See page D147 for TungFlex modular shank.

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HFWX04M... SR34-514 M-1000 T-7F

INSERT
W XH U -M J
T
ød

rε
P Steel 
M Stainless
K Cast iron
N Non-ferrous
S Superalloys : First choice
H Hard materials  : Second choice
Coated
Profile Milling

rε Max.
AH110

Designation ap ød T

WXHU040305R-MJ 0.020 0.020 z 0.250 0.125

WXHU040310R-MJ 0.039 0.039 z 0.250 0.125

* For plunging, width up to 0.079" is possible. z: Line up

STA NDA RD CUT TING CONDITIONS

Hardness Cutting speed Feed per tooth
ISO Workpiece materials Grades
(HB) Vc (sfm) fz (ipt)
High carbon steel
200 - 300 AH110 328 - 984 0.004 - 0.012
(1045, 1055, etc.)
Alloy steel
150 - 300 AH110 328 - 984 0.004 - 0.012
(4140, etc.)
Prehardened steel
- AH110 328 - 984 0.002 - 0.012
(NAK80, PX5, etc.)

(H13, etc.) - AH110 262 - 427 0.004 - 0.012

Hardened steel
(D2, etc.) - AH110 164 - 328 0.002 - 0.006

D148 www.tungaloyamerica.com
MEMO

Profile Milling

Tungaloy D149
 TR P12/16
Ra d i u s c u t te r ser i es b o re t y p e w i t h ant i - ro t a t i on s y s te m

A.R. = +4°, R.R. = -4°

øDb
ød R R R

b
a

R
Lf
ap
øDc
øD 1
Inch Max. ap øDc z øD1 øDb ød ℓ Lf b a Ib Air hole Insert
TRP12R200U0075A05 0.236 1.526 5 2.000 1.850 0.750 0.750 1.575 0.197 0.315 0.66 with RPMT1204EN-M*
TRP12R250U0100A06 0.236 2.026 6 2.500 2.323 1.000 1.024 1.969 0.236 0.374 1.32 with RPMT1204EN-M*
TRP16R250U0100A05 0.315 1.869 5 2.500 2.323 1.000 1.024 1.969 0.236 0.374 1.32 with RPMT1606EN-M*

SPARE PARTS
Designation Clamping screw Grip Lubricant Center bolt Torx bit
(Optional parts)
TRP12R... CSTR-4L100 H-TBS M-1000 (C0.375X1.125H) BT15S
TRP16R... CSPB-5 H-TBS M-1000 (C0.375X1.125H) BLDIP20/S7

ER P 10/12/16
Ra d i u s c u t te r ser i es shank t y p e w i t h ant i - rot a t i on s y s te m

A.R. = +10°~ +4°, R.R. = -2°~ -8.5°

R R
øD 1

øDs
øDc

ap
Lf Rs
L
Profile Milling

Inch Max. ap øDc z øD1 øDs ℓs Lf L Air hole Insert

ERP10R100U0100-02 0.197 0.776 2 1.000 1.000 4.000 2.000 6.000 with RPMT10T3EN-M*
ERP10R125U0125-04 0.197 1.034 4 1.250 1.250 4.000 2.000 6.000 with RPMT10T3EN-M*
ERP10R150U0125-04 0.197 0.866 4 1.500 1.250 4.000 2.000 6.000 with RPMT10T3EN-M*
ERP12R125U0125-03 0.236 0.776 3 1.250 1.250 4.000 2.000 6.000 with RPMT1204EN-M*
ERP12R150U0125-04 0.236 1.034 4 1.500 1.250 4.000 2.000 6.000 with RPMT1204EN-M*
ERP16R150U0125-02 0.315 0.866 2 1.500 1.250 4.000 2.000 6.000 with RPMT1606EN-M*

SPARE PARTS
Designation Clamping screw Lubricant Wrench
ERP10R... CSPB-3.5S M-1000 IP-15D
ERP12R... CSTR-4L100 M-1000 T-15DB
ERP16R... CSPB-5 M-1000 IP-20D

Reference pages
Inserts → D151, Standard cutting conditions → D152 - D153

D150 www.tungaloyamerica.com
HR P-M
R a d i u s c u t te r s e r i es m o d ul ar t y p e ( Tung Fl ex) w i t h a n t i - rot a t i on s y s te m

A.R. = 1°~ 4°, R.R. = -8.5°~ 2°

L6
Lf Ts R R R
C A T

øD3
øDc
øD1
ap A A-A cross section

Metric Max. ap øDc z øD1 L6 Lf C T øD3 Ts Kg Air hole Insert

HRP10R020MM10-02 5 10 2 20 49 30 10 15 17.8 M10 0.1 with RPMT10T3...
HRP10R025MM12-02 5 15 2 25 57 35 10 17 20.8 M12 0.1 with RPMT10T3...
HRP10R032MM16-04 5 22 4 32 63 40 12 22 28.8 M16 0.2 with RPMT10T3...
HRP12R032MM16-03 6 20 3 32 63 40 12 22 28.8 M16 0.2 with RPMT1204...
See page D147 for TungFlex modular shank.

SPARE PARTS
Wrench
Designation Clamping screw Lubricant
Bit Grip
HRP10R... CSPB-3.5S M-1000 BLD IP15/S7 H-TBS
HRP12R... CSTR-4L100 M-1000 BT15S H-TBS

INSERT
RP M T-M J R PM T-M L
A T A T

11° 11°

P Steel 
M Stainless 
K Cast iron 

Profile Milling
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated
AH4035

Max.
AH725
AH130

Designation ap A T

RPMT10T3EN-MJ 0.197 z z z 0.394 0.156

RPMT10T3EN-ML 0.197 z z z 0.394 0.156
RPMT1204EN-MJ 0.236 z z z 0.472 0.187
RPMT1204EN-ML 0.236 z z z 0.472 0.187
RPMT1606EN-MJ 0.315 z z z 0.630 0.250
RPMT1606EN-ML 0.315 z z z 0.630 0.250
z: Line up

Reference pages
Standard cutting conditions → D152 - D153

Tungaloy D151
 STA NDA RD CUT TING CONDITIONS

Cutting Feed
ISO Chip-
Workpiece material Hardness Priority Grade speed per tooth
breaker Vc (sfm) fz (ipt)

< 300 HB First choice AH725 MJ 400 -830 0.012 - 0.028

Carbon steels
(1045, 1055 etc.)
< 300 HB For impact resistance AH130 MJ 400 -830 0.012 - 0.028

150 - 300 HB First choice AH725 MJ 330 -830 0.008 - 0.024

Alloy steels
(4140(H) etc.)
150 - 300 HB For impact resistance AH130 MJ 330 -830 0.008 - 0.024

Tool steels
< 300 HB - AH725 ML 260 - 590 0.008 - 0.016
(W1-10, M2 etc.)

< 200 HB First choice AH130 ML 330 -830 0.008 - 0.024

Stainless steels
(304, 316 etc.)
< 200 HB For impact resistance AH130 MJ 330 -830 0.008 - 0.024

< 200 HB First choice AH4035 ML 330 -1000 0.008 - 0.024

Stainless steels
(420, 430 etc.)
< 200 HB For impact resistance AH4035 MJ 330 -1000 0.008 - 0.024

Gray cast irons

150 - 250 HB - AH725 ML 400 - 830 0.012 - 0.028
(No.25, No.30 etc.)

Ductile cast irons

150 - 250 HB - AH725 ML 330 - 660 0.012 - 0.028
(60-40-18 etc.)

Heat-resistant alloys
- - AH725 MJ 200 - 530 0.006 - 0.010
Inconel718, etc.

Titanium alloys
- - AH725 ML 200 - 530 0.006 - 0.010
Ti-6AI-4V, etc.

Hardened steels
40 - 50 HRC - AH725 MJ 200 - 460 0.004 - 0.012
(H13 etc.)

Hardened steels
50 - 60 HRC - AH725 MJ 70 - 200 0.002 - 0.008
(D2 etc.)
Profile Milling

· Use air blast to remove chips from the work area in slot milling or · Cutting conditions are limited by machine power, workpiece rigid-
pocketing operation. ity and spindle output. When the cutting width or depth is large,
· When machining at high cutting speeds of more than Vc = 3281 set Vc and fz to the lower recommended values and check the
sfm, the dynamic balance of the tools must be adjusted. machine power and vibration.

D152 www.tungaloyamerica.com
 Tool dia.: øDc (in), Number of revolutions: n (rpm), Feed speed: Vf (ipm), Depth of cut: ap = 0.078"
ø1.000 ø1.250 ø1.500 ø2.000 ø2.500
Vf Vf Vf Vf
n Vf n n n n
ERP10 ERP12 ERP10/12 ERP16 TRP12 TRP16
2250 90 1790 143 110 1430 120 60 1150 110 910 110 90
Vc = 590 sfm, fz = 0.020 ipt
2250 90 1790 143 110 1430 120 60 1150 110 910 110 90
Vc = 590 sfm, fz = 0.020 ipt
2140 68 1690 108 80 1350 90 45 1080 85 860 80 70
Vc = 560 sfm, fz = 0.016 ipt
2140 51 1690 81 60 1350 90 45 1080 85 860 80 470
Vc = 560 sfm, fz = 0.012 ipt
1600 38 1290 62 45 1030 50 25 830 50 660 45 40
Vc = 420 sfm, fz = 0.016 ipt
2140 68 1690 108 80 1350 90 45 1080 52 860 80 70
Vc = 560 sfm, fz = 0.016 ipt
2140 68 1690 108 80 1350 90 45 1080 52 860 80 70
Vc = 560 sfm, fz = 0.016 ipt
2520 81 1990 127 95 1590 110 55 1270 100 1010 95 80
Vc = 660 sfm, fz = 0.016 ipt
2520 81 1990 127 95 1590 110 55 1270 100 1010 95 80
Vc = 660 sfm, fz = 0.016 ipt
2250 90 1790 143 110 1430 120 60 1150 110 910 110 90
Vc = 590 sfm, fz = 0.020 ipt
1910 76 1490 119 90 1190 100 50 950 90 760 90 75
Vc = 500 sfm, fz = 0.020 ipt
1340 21 1070 34 25 890 28 14 670 27 530 25 21
Vc = 350 sfm, fz = 0.008 ipt
1340 21 1070 34 25 890 28 14 670 27 530 25 21
Vc = 350 sfm, fz = 0.008 ipt
1260 20 990 32 25 800 25 15 640 25 510 25 20
Vc = 330 sfm, fz = 0.008 ipt
530 5 400 8 6 320 10 5 250 10 200 10 8
Vc = 140 sfm, fz = 0.005 ipt

Profile Milling
Notification for clamping
· When installing the insert, please carefully locate the insert in the seat and fasten the screw.

OK

Make sure the insert cavity fits the protrusion

on the body

Tungaloy D153
 A PPLICATION R A NGE

Shoulder Helical
Slotting Ramping Plunging Traversing interpolation
milling

A
ap

ap
θ

L øD1, 2

Machining length
Max. depth Max. ramping Max. plunging for removing uncut
Tool-ø of cut angle depth portion Min. machining *Max. machining

Inch øDc (in) ap (in) θº A (in) L (in) øD1 (in) øD2 (in)
ERP10R100U0100-02 1.000 0.197 3 0.0276 0.630 1.457 1.969

ERP10R125U0125-04 1.250 0.197 8 0.0984 0.866 1.811 2.441

ERP10R150U0125-04 1.500 0.197 6 0.0984 1.142 2.283 2.953

ERP12R125U0125-03 1.250 0.236 8.3 0.0906 0.787 1.693 2.441

ERP12R150U0125-04 1.500 0.236 4 0.0630 1.063 2.244 2.953

ERP16R150U0125-02 1.500 0.315 6 0.0709 0.906 2.008 2.953

TRP12R200U0075A05 2.000 0.236 4 0.0984 1.575 3.189 3.937

TRP12R250U0100A06 2.500 0.236 2.7 0.0906 2.047 4.213 4.921

TRP16R250U0100A05 2.500 0.315 3 0.0906 1.890 3.976 4.921

*For flat bottom hole

Profile Milling

D154 www.tungaloyamerica.com
T R C 12/16
Fa c e m i l l s w i t h b u t to n i n s e r t o f 0 . 2 3 6 " ( 6 m m ) o r 0 . 3 1 5 " ( 8 m m ) ra d i u s
A.R. = +0°, R.R. = -1°~ -5°
øDb
ød

b
R R R
a

R
Lf
øDc

ap
øD1

Inch Max. ap øDc z øD1 øDb Lf ød ℓ a b Ib Air hole Insert

TRC12R200U0075A05 0.236 1.528 5 2.000 1.850 2.000 0.750 0.750 0.320 0.200 0.880 with RCMT1204...
TRC12R250U0075A06 0.236 2.028 6 2.500 2.320 2.000 0.750 0.750 0.320 0.200 1.540 with RCMT1204...
TRC12R300U0100A07 0.315 2.528 7 3.000 2.830 2.500 1.000 1.020 0.370 0.240 2.860 with RCMT1204...
TRC16R200U0075A04 0.315 1.370 4 2.000 1.850 2.000 0.750 0.750 0.320 0.200 0.880 with RCMT1204...
TRC16R250U0075A05 0.315 1.870 5 2.500 2.320 2.000 0.750 0 .750 0.320 0.200 1.540 with RCMT1204...
TRC16R300U0100A06 0.315 2.370 6 3.000 2.830 2.500 1.000 1.020 0.370 0.240 2.860 with RCMT1204...
TRC16R400U0150A07 0.315 3.370 7 4.000 3.820 2.500 1.500 1.460 0.620 0.390 3.520 with RCMT1204...
TRC16R500U0150A08 0.315 4.370 8 5.000 3.780 2.500 1.500 1.460 0.620 0.390 7.930 with RCMT1204...

SPARE PARTS
Designation Clamping screw Grip Center bolt Center bolt 1 Torx bit
TRC12R... CSTB-4L090 H-TBS - C0.375X1.125H BT15S
TRC16R200, 250... CSTB-5L120 H-TB - C0.375X1.125H BT20S
TRC16R300... CSTB-5L120 H-TB - C0.500X1.375H BT20M
TRC16R400, 500... CSTB-5L120 H-TB TMBA-0.750H - BT20M

Profile Milling

Reference pages
Inserts → D157, Standard cutting conditions → D158

Tungaloy D155
 ER C 12/16
I n d ex a b l e e n d m i l l s w i t h b u t to n i n s e r t o f 0 . 2 3 6 " ( 6 m m ) o r 0 . 3 1 5 " ( 8 m m ) ra d i u s
A.R. = +0°, R.R. = -1°~ -5°

R R R

øDc
øD1

øDs
ap Lf Rs
L

Inch Max. ap øDc z øD1 øDs L Lf ℓs Ib Air hole Insert

ERC12R125U0125-03L 0.236 0.778 3 1.25 1.25 6 2.25 3.75 2.05 with RCMT1204*N-***
ERC12R125U0125-03LL 0.236 0.778 3 1.25 1.25 12 7 5 3.37 with RCMT1204*N-***.
ERC12R125U0125-03LM 0.236 0.778 3 1.25 1.25 8 4 4 2.25 with RCMT1204*N-***
ERC12R125U0125W03 0.236 0.778 3 1.25 1.25 5 2.75 2.25 1.32 with RCMT1204*N-***
ERC12R125U150-03LL 0.236 0.778 3 1.25 1.5 12 7 5 4.19 with RCMT1204*N-***
ERC12R150U0125-04LM 0.236 1.028 4 1.5 1.25 8 4 4 2.36 with RCMT1204*N-***
ERC12R150U0125-04LX 0.236 1.028 4 1.5 1.25 12 7 5 3.55 with RCMT1204*N-***
ERC12R150U0125W04 0.236 1.028 4 1.5 1.25 5 2.34 2.66 1.43 with RCMT1204*N-***
ERC12R150U0150-04L 0.236 1.028 4 1.5 1.5 6 2 3.75 2.42 with RCMT1204*N-***
ERC12R150U0150-04LM 0.236 1.028 4 1.5 1.5 8 4 4 3.08 with RCMT1204*N-***
ERC12R150U0150-04LX 0.236 1.028 4 1.5 1.5 12 7 5 4.41 with RCMT1204*N-***
ERC12R150U0150W04 0.236 1.028 4 1.5 1.5 5 2.34 2.66 1.83 with RCMT1204*N-***
ERC12R150U150-04LL 0.236 1.028 4 1.5 1.5 12 2 10 5.29 with RCMT1204*N-***
ERC16R150U0125-02LL 0.315 0.87 2 1.5 1.25 12 2 10 3.81 without RCMT1606*N-***
ERC16R150U0125-02LM 0.315 0.87 2 1.5 1.25 8 2 6 2.47 with RCMT1606*N-***
ERC16R150U0125W02 0.315 0.87 2 1.5 1.25 5 2.34 2.66 1.43 with RCMT1606*N-***
ERC16R150U0150-02L 0.315 0.87 2 1.5 1.5 6 2 4 2.38 with RCMT1606*N-***
ERC16R150U0150-02LM 0.315 0.87 2 1.5 1.5 8 4 4 3.08 with RCMT1606*N-***
ERC16R150U0150-02LX 0.315 0.87 2 1.5 1.5 12 7 5 4.62 without RCMT1606*N-***
ERC16R150U0150W02 0.315 0.87 2 1.5 1.5 5 2.34 2.66 1.83 with RCMT1606*N-***
ERC16R150U150-02LL 0.315 0.87 2 1.5 1.5 12 2 10 5.29 without RCMT1606*N-***

SPARE PARTS
Designation Clamping screw Wrench
ERC12R... CSTB-4L090 T-15DB
ERC16R040... CSTB-5L105 T-20DB
Profile Milling

ERC16R050... CSTB-5L120 T-20DB

Reference pages
Inserts → D157, Standard cutting conditions → D158

D156 www.tungaloyamerica.com
 INSERT
RC M T-M J R C M T-N M J
A T A T

RC M T-N AJ
A T

P Steel  
M Stainless 
K Cast iron  
N Non-ferrous 
S Superalloys   : First choice
H Hard materials : Second choice
Coated Un-
coated

Max.
AH725
AH120
AH140

KS15F

Designation ap A T

RCMT1204EN-NMJ 0.236 z z z 0.472 0.189

RCMT1204EN-MJ 0.236 z z z 0.472 0.189
RCMT1204FN-NAJ 0.236 z 0.472 0.189
RCMT1606EN-NMJ 0.315 z z z 0.630 0.256
RCMT1606EN-MJ 0.315 z z z 0.630 0.256
RCMT1606FN-NAJ 0.315 z 0.630 0.256

z: Line up

Profile Milling

Tungaloy D157
 STA NDA RD CUT TING CONDITIONS
Feed per tooth fz (ipt)
Hardness Cutting speed each chipbreaker
ISO Workpiece material Grade
HB Vc (SFM)
MJ NMJ NAJ

Low carbon steels (1010, 1015, etc.) ~ 200 AH725 330 - 720 0.008 - 0.028 0.007 - 0.012 -

High carbon steels (1045, 1055, etc.) 200 ~ 300 AH725 330 - 660 0.008 - 0.028 0.007 - 0.010 -

Alloyed steels (4140, 5120, etc.) 150 ~ 300 AH725 330 - 660 0.008 - 0.028 0.007 - 0.010 -

Tool steels (D3, etc.) ~ 300 AH725 330 - 590 0.008 - 0.028 0.007 - 0.010 -

Stainless steels
- AH140 300 - 590 0.008 - 0.024 0.006 - 0.010 -
(304, 316, etc.)

Grey cast irons (No.250B, etc.) 500 ~ 820 AH120 460 - 820 0.008 - 0.028 0.007 - 0.012 -

Ductile cast irons (60-40-18, etc.) 500 ~ 820 AH120 460 - 820 0.008 - 0.028 0.007 - .0012 -

Aluminum alloys (Si < 13%) - KS15F 1640 - 3940 - - 0.004 - 0.012

Aluminum alloys (Si ≥ 13%) - KS15F 330 - 980 - - 0.004 - .0012

Heat-resisting alloy
- AH725 70 - 160 0.008 - 0.024 0.006 - 0.010 -
(Inconel 718, Ti-6Al-4V etc.)

· To remove excessive chip accumulation use an air blast. · Cutting conditions are limited by machine power and material
· When chips stick to the cutting edges (aluminum machining), rigidity. When the cutting width or depth is large, set Vc and fz
use a water soluble cutting fluid. below the recommended values and check the machine
vibration and spindle load.
Profile Milling

D158 www.tungaloyamerica.com
Holemaking with helical feed
Tool ø Min. machining Max. machining
diameter (in) diameter (in) Pitch
Designation øDc
øD P (in)
(in) øD øD1 øD øD1
øD1 ERC12R125U… 1.250 2.028 0.778 2.421 1.171 < 0.236
P ERC12R150U… 1.500 2.528 1.028 2.921 1.421 < 0.236

TRC12R200U… 2.000 3.528 1.528 3.921 1.921 < 0.236

TRC12R250U… 2.500 4.528 2.028 4.921 2.421 < 0.236

TRC12R300U… 3.000 5.528 2.528 5.921 2.921 < 0.236

ERC16R150U… 1.500 2.370 0.870 2.921 1.421 < 0.315

TRC16R200U… 2.000 3.370 1.370 3.921 1.921 < 0.315

TRC16R250U… 2.500 4.370 1.870 4.921 2.421 < 0.315

TRC16R300U… 3.000 5.370 2.370 5.921 2.921 < 0.315

TRC16R400U… 4.000 7.370 3.370 7.921 3.921 < 0.315

TRC16R500U… 5.000 9.370 4.370 9.921 4.921 < 0.315

When holemaking with a helical feed, the pitch (P) needs to be set at lower values than that shown above.

Ramping Tool ø
Max. L: tool pass length when
ramping ramping angle is 2 degrees
Designation øDc
angle ap (in)
(in)
θ° 0.079 0.118 0.158 0.236 0.315
L ERC12R125U… 1.250 10 2.244 3.346 4.488 6.732 −
ERC12R150U… 1.500 7 2.244 3.346 4.488 6.732 −
TRC12R200U… 2.000 5.5 2.244 3.346 4.488 6.732 −
TRC12R250U… 2.500 3.5 2.244 3.346 4.488 6.732 −
TRC12R300U… 3.000 2.5 2.244 3.346 4.488 6.732 −
ERC16R150U… 1.500 16 2.244 3.346 4.488 6.732 −
TRC16R200U… 2.000 9.5 2.244 3.346 4.488 6.732 9.016

θ TRC16R250U… 2.500 6.5 2.244 3.346 4.488 6.732 9.016

ap

TRC16R300U… 3.000 4.5 2.244 3.346 4.488 6.732 9.016

TRC16R400U… 4.000 3 2.244 3.346 4.488 6.732 9.016

TRC16R500U… 5.000 2.5 2.244 3.346 4.488 6.732 9.016

Tool pass length: L = ap / tan θ, Ramping angle needs to be set at smaller than 2 de-
grees in order to prevent chips from getting tangled.

Profile Milling
T R D 12/16
Fa c e m i l l s w i t h b u t to n i n s e r t o f 0 . 2 3 6 " ( 6 m m ) o r 0 . 3 1 5 " ( 8 m m ) ra d i u s
A.R. = +10°, R.R. = -6°~ 0°
ød
a R R R
b
R
Lf

øDc rε
øD1

Inch Max. ap øDc z øD1 Lf ød ℓ a b rε Ib Insert

TRD12050RU 0.236 1.528 4 2.00 1.560 0.750 1.570 0.315 0.197 0.236 0.990 RDM*1204...
TRD16080RU 0.315 2.520 4 3.15 2.000 1.000 1.970 0.375 0.236 0.315 1.600 RDM*1606...
TRD16100RU 0.315 3.310 5 3.94 2.000 1.250 1.970 0.500 0.315 0.315 2.200 RDM*1606...
TRD16125RU 0.315 4.290 6 4.92 2.500 1.500 2.480 0.625 0.394 0.315 5.300 RDM*1606...

SPARE PARTS
Designation Clamp screw Wrench
TRD12... CSTB-3.5 T-15D
TRD16... CSTB-5 T-20D

Reference pages
Inserts → D160, Standard cutting conditions → D161

Tungaloy D159
 ER D 12
I n d ex a b l e e n d m i l l s w i t h b u t to n i n s e r t o f 0 . 2 3 6 " ( 6 m m ) o r 0 . 3 1 5 " ( 8 m m ) ra d i u s

A.R. = +8°~ 10°, R.R. = -6°~ -2°

øDsh6
øDc
øD1
Lf Rs
L

Inch Max. ap øDc z øD1 øDs L Lf ℓs Insert

ERD12125RSU 0.236 0.778 2 1.250 1.250 4.780 1.970 2.280 RDM*1204...
ERD12150RSU 0.236 1.028 3 1.500 1.500 4.780 1.970 2.280 RDM*1204...
ERD12200RSU 0.236 1.528 4 2.000 2.000 4.780 1.970 2.280 RDM*1204...
ERD12125RLU 0.236 1.250 2 1.250 1.250 10.000 1.970 7.500 RDM*1204...
ERD12150RLU 0.236 1.500 3 1.500 1.500 10.000 1.970 7.500 RDM*1204...
ERD12200RLU 0.236 2.000 4 2.000 2.000 10.000 1.970 7.500 RDM*1204...

SPARE PARTS
Designation Clamp screw Lubricant Wrench
ERD12**R... CSTB-3.5 M-1000 T-15D

INSERT
R D M T12/16- M J RDMW12/16
Button insert with pressed MJ chipbreaker Flat-top button insert with 0.236" (6 mm) or 0.315"
(8 mm) radius
4-rε 4-rε

bs
bs

A
A

15° 15°
T T

P Steel   
M Stainless 
K Cast iron 
N Non-ferrous
Profile Milling

S Superalloys  : First choice

H Hard materials : Second choice
Coated Un-
coated

rε Max.
AH330
AH130
AH120

AH140

T3130

Designation A T bs
UX30

ap

RDMT1204ZDPN-MJ 0.236 0.236 z z z z z 0.504 0.187 0.031

RDMW1204ZDSN 0.236 0.236 z 0.504 0.187 0.031
RDMT1606ZDPN-MJ 0.315 0.315 z z z z z z 0.661 0.250 0.031
RDMW1606ZDSN 0.315 0.315 z 0.661 0.250 0.031

z: Line up

Reference pages
Standard cutting conditions → D161

D160 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Cutting speed Feed per tooth: fz (ipt)
ISO Workpiece material Grade
Vc (sfm) T/ERD12 T/ERD16
AH120 390 ~ 720 0.012 ~ 0.020 0.012 ~ 0.024
Carbon steels (1018,1055)
AH330 460 ~ 790 0.008 ~ 0.016 0.008 ~ 0.020
< 300 HB
UX30 260 ~ 390 0.008 ~ 0.016 0.008 ~ 0.020

AH120 330 ~ 660 0.008 ~ 0.018 0.008 ~0.020

Alloy steels (4140, 4340)
AH330 390 ~ 720 0.006 ~ 0.014 0.006 ~0.016
< 300 HB
UX30 200 ~ 390 0.006 ~ 0.014 0.006 ~ 0.016

AH120 260 ~ 590 0.008 ~ 0.014 0.010 ~ 0.018

Die steels (H13,P20 etc.)
< 300 HB
AH330 330 ~ 660 0.004 ~ 0.012 0.004 ~ 0.016

Stainless steels (JIS SUS304 etc.) AH130∙AH140 330 ~ 660 0.008 ~ 0.012 0.008 ~ 0.016

AH120 390 ~ 790 0.012 ~ 0.020 0.012 ~ 0.024

Grey Cast irons
(JIS CLASS 25-40)
AH330 490 ~ 820 0.008 ~ 0.016 0.008 ~ 0.020

Hard materials < A980 AH120 200 ~ 460 0.003 ~ 0.010 0.004 ~ 0.012

Note: When the depth of cut is smaller than 0.078", use the higher limit of feed values shown
above. When larger than 0.118", use the lower limit of the feed values.

Plunging + traverse feed milling Ramping Helical feed drilling

(Unit: in)
Plunging Traverse feed milling
Remaining projection
P

L
L Feed øD
Feed

Feed
ap
ap

θ°

øD1
øD ae

Max. Max. Min. traverse length Min. Max.

plunging ramping to flatten the machining machining Pitch øDc-ra

Profile Milling
depth angle bottom surface diameter diameter
Inch øD1 ap θ° L øD øD P ae
TRD1205RU 2.00 0.157 8 1.567 3.47 3.86 < 0.236 0.157
TRD16080RU 3.15 0.216 4 2.559 5.67 6.22 < 0.315 0.216
TRD16100RU 3.94 0.216 3 3.349 7.24 7.80 < 0.315 0.216
TRD16125RU 4.92 0.216 2 4.329 9.21 9.76 < 0.315 0.216
ERD12125RSU/RLU 1.25 0.157 16 0.817 2.05 2.44 < 0.236 0.157
ERD12150RSU/RLU 1.50 0.157 8 1.067 2.68 3.07 < 0.236 0.157
ERD12200RSU/RLU 2.00 0.157 6 1.567 3.47 3.86 < 0.236 0.157

øD 1 : Tool diameter
øD : Drilling diameter
P : Z-axis feed per one round of tool pass (Pitch of helical cycle)
Notes: • In plunging, the maximum plunging depth is limited as shown in the above table.
• In plunging, set the Z-axis feed in a range of 0.0019 to 0.0039 ipt.
• When plunging, use peck-feed every 0.039" (or smaller than 0.039") to break chips.
• tanθ = depth of cut: ap / length of tool pass: L
• In ramping, the ramping angle should be set within the maximum ramping angle.
• In helical feed hole machining, the machinable hole diameters are limited by the tool diameter as shown in the above tables.
• When machining between the minimum and maximum machining diameters, a projection remains in the center of the bottom surface of the hole
as shown in the Figure at right. Remove it by traverse feed milling.

Tungaloy D161
 E W D 05/07/1 0
I n d ex a b l e e n d m i l l s w i t h b ut to m i nser t s o f 0. 098" , 0. 138" , a n d 0. 196" (2. 5, 3. 5, a n d 5 m m ) ra d i u s

A.R. = 0°, R.R. = -3°~ +0.5°

R R R

øD1
øDc

øDsh6
Lf Rs
L

Inch Max. ap øDc z øD1 øDs ℓs Lf L Air hole Insert

EWD05050RU 0.098 0.304 2 0.500 0.750 3.250 0.750 5.000 with RDMW0501M0
EWD05075RU 0.098 0.554 3 0.750 1.000 5.000 1.500 7.000 with RDMW0501M0
EWD07075RU 0.138 0.475 4 0.750 1.000 5.000 1.500 7.000 with RDMW0702M0
EWD07100RU 0.138 0.725 5 1.000 1.250 5.250 1.750 8.000 with RDMW0702M0
EWD07125RU 0.138 0.975 3 1.250 1.500 5.500 1.750 9.000 with RDMW0702M0
EWD10100RU 0.196 0.606 3 1.000 1.250 5.250 1.750 8.000 with RDMW1003M0
EWD10125RU 0.196 0.856 5 1.250 1.500 5.500 1.750 9.000 with RDMW1003M0

SPARE PARTS
Designation Clamping screw Wrench
EWD05050RU CSTD-1.8 T-6D
EWD05075RU CSTD-1.8 T-6D
EWD07075RU CSTB-2.5S T-8D
EWD07100RU CSTB-2.5S T-8D
EWD07125RU CSTB-2.5S T-8D
EWD10100RU CSTB-3.5H T-15D
EWD10125RU CSTB-3.5H T-15D

H W D 07-M
I n d ex a b l e e n d m i l l s w i t h Tu n g F l ex , c a r r y i n g b u t to m i n s e r t s o f 3 . 5 m m ra d i u s
A.R. = 0°, R.R. = -3°~ +0.5°
L6
Lf Ts R R R
C A T
Profile Milling

øD1
øDc

øD3

ap A A-A cross section

Metric Max. ap øDc z øD1 L6 Lf C T øD3 Ts Kg Air hole

HWD07R015MM08-03 3.5 8 3 15 42 25 8 10 12.8 M8 0.03 with
HWD07R020MM10-04 3.5 13 4 20 49 30 10 15 17.8 M10 0.06 with
HWD07R025MM12-05 3.5 18 5 25 57 35 10 17 20.8 M12 0.1 with
HWD07R030MM16-05 3.5 23 5 30 63 40 12 22 28.8 M16 0.2 with
See page D147 for TungFlex modular shank.

SPARE PARTS
Designation Clamping screw Lubricant Wrench
HWD07-M... CSTB-2.5S M-1000 T-8D

Reference pages
Inserts, Standard cutting conditions → D163

D162 www.tungaloyamerica.com
 INSERT
RD M W 05/07/1 0
A T

15°

P Steel 
M Stainless
K Cast iron 
N Non-ferrous
S Superalloys  : First choice
H Hard materials : Second choice
Coated

Designation Max. AH120 A T

ap

RDMW0501M0 0.098 z 0.197 0.055

RDMW0702M0 0.138 z 0.276 0.094
RDMW1003M0 0.196 z 0.394 3.180
z: Line up
STA NDA RD CUT TING CONDITIONS
Cutting speed Feed per tooth Depth of cut ap (in)
ISO Workpiece material Grade
Vc (sfm) fz (ipt) Cutter dia. ø10, 12 Cutter dia. ø15, 20 Cutter dia. ø25

Carbon steels (1018,1055) < 300 HB AH120 650 - 1640 0.006 - 0.018 - 0.020 - 0.028 - 0.039

Alloy steels (4140, 4340) < 300 HB AH120 390 - 1150 0.006 - 0.014 - 0.020 - 0.028 - 0.039

Die steels (H13,P20 etc.) < 300 HB AH120 330 - 980 0.004 - 0.012 - 0.020 - 0.028 - 0.039

Cast irons (JIS CLASS 25-40) AH120 660 - 1640 0.008 - 0.020 - 0.020 - 0.028 - 0.039

Hardened steels,
AH120 230 - 660 0.004 - 0.010 - 0.020 - 0.028 - 0.039
Prehardened steels < 40HRC

Profile Milling
A PPLICATION R A NGE (HWD 07- M )
Shoulder Slotting Ramping Plunging Traversing Helical
milling interpolation
ap

ap

L øD1,2

Max. Machining length

Max. Max. Max. *Max.
Tool-ø plunging for removing
depth of cut ramping uncut portion machining machining
depth
Inch øDc (mm) ap θ˚ A L øD1 øD2
HWD07R015MM08-03 15 0.138 25 0.079 øD c - 0.236 0.906 1.102

HWD07R020MM10-04 20 0.138 11 0.079 øD c - 0.236 1.299 1.496

HWD07R025MM12-05 25 0.138 7 0.079 øD c - 0.236 1.693 1.890

HWD07R030MM16-05 30 0.138 5.5 0.079 øD c - 0.236 2.087 2.283

*For flat bottom hole

Tungaloy D163
 EB P
I n d ex a b l e b a l l - no se end m i l l f o r sem i - f i ni sh i n g

øDsh6
L L
EBP***SE-E rε Rs
Lf Rs Lf
R

øDc

øDs
øDc
rε ap ap
L3 L
L EBP***MME-E
Lf Rs
EBP***MDE-E rε Lf Rs rε
MK

øDc
øDc

øDs
ap ap

Inch Max. ap øDc z øDs ℓs Lf L L3 rε MK Insert 1 Insert 2

EBP075MWU 0.625 0.750 2 1.000 2.280 2.750 5.030 1.250 0.375 - ZPET075MJ -
EBP100MWU 0.827 1.000 2 1.000 2.280 3.250 5.530 - 0.500 - ZPET100MJ -
EBP125MWU 1.000 1.250 2 1.250 2.280 3.750 6.030 - 0.625 - ZPET125MJ -
EBP075LWEU 1.140 0.750 2+2 1.000 2.280 3.750 6.030 1.250 0.375 MK2 ZPET075MJ DCMW070204TN
EBP100LWEU 1.610 1.000 2+2 1.000 2.280 4.250 6.530 - 0.500 - ZPET100MJ DCMW11T304TN
EBP125LWEU 1.810 1.250 2+2 1.250 2.280 4.750 7.030 - 0.625 - ZPET125MJ DCMW11T304TN

SPARE PARTS
Clamping screw Clamping screw Wrench Wrench 1
Designation
for Insert 1 for Insert 2 for Insert 1 for Insert 1
EBP075MWU CSTD-3T - T-10D -
EBP100MWU CSTB-4S - T-15D -
EBP125MWU CSTB-5S - T-20D -
EBP075LWEU CSTD-3T CSTB-2.5S T-10D T-8D
EBP100LWEU CSTB-4S CSTB-4S T-15D T-15D
EBP125LWEU CSTB-5S CSTB-4S T-20D T-15D

INSERT
ZP E T-M J ( f or Rad i us ) D C M W -T N ( f o r Pe r ip h e ra l)
rε rε T
A

T 7°

P Steel 
Profile Milling

M Stainless
K Cast iron 
N Non-ferrous
S Superalloys : First choice
H Hard materials  : Second choice
Coated
AH330
AH120

Designation rε A T

ZPET075-MJ 0.375 z z - 0.177

ZPET100-MJ 0.500 z z - 0.182
ZPET125-MJ 0.625 z z - 0.266
DCMW070204TN 0.016 z z 0.252 0.266
DCMW11T304TN 0.016 z z 0.375 0.094

z: Line up

Reference pages
Standard cutting conditions → D165

D164 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
EBP
Machining Cutting speed Table feed vf (in/min)
ISO Workpiece material Grade
type Vc (sfm) Tool dia. : ø0.750 Tool dia. : ø25 Tool dia. : ø30
AH120 (1) 550 - 750 24 - 30 18 - 30 14 - 26
Carbon steels
(1055 etc.) AH120 (2) 650 - 850 35 - 51 27 - 43 21 - 37
< 300 HB
AH120 (3) 500 - 650 14 - 23 12 - 24 9 - 21

AH120 (1) 500 - 690 21 - 33 16 - 28 12 - 24

Alloy steels
AH120 (2) 590 - 780 32 - 47 16 - 32 19 - 34
(4140, 4340)
< 300 HB
AH120 (3) 425 - 590 14 - 26 10 - 22 8 - 19

AH330 (1) 400 - 590 17 - 28 12 - 24 9 - 21

Die steels
(JIS SKD11 etc.) AH330 (2) 500 - 690 26 - 42 19 - 35 15 - 30
< 300 HB
AH330 (3) 330 - 500 10 - 22 7 - 19 5 - 17

AH120 (1) 550 - 750 32 - 43 24 - 36 19 - 31

Cast irons
(JIS CLASS 25-40) AH120 (2) 650 - 850 35 - 55 28 - 47 21 - 41

AH120 (3) 500 - 650 17 - 28 12 - 24 9 - 21

AH120 (1) 200 - 330 6 - 14 4 - 12 4 - 10

Hardened steels
Prehardened steels AH120 (2) 230 - 425 6 - 18 4 ~16 4 - 14
< A980
AH120 (3) 130 - 260 6 - 10 4-8 3-7
Notes:
• Cutting speeds shown in the left table are of the most outer diameter of the tool.
• The values of the cutting speeds and feeds shown in the table are of under general cutting conditions. The values should be modified depending on the power
and rigidity of the machine to be used, and work holding conditions.
• When using the long shank type, the depth of cut, pick feed, cutting speed, and table feed should be reduced to 70 %-90 % of the values shown in the tables.

EBD
Machining Cutting speed Table feed vf (in/min)
ISO Workpiece material Grade
type Vc (sfm) Tool dia.: ø1.57 TTool dia.: ø2.00
AH120 (1) 500 - 690 16 - 22 3 - 18
Carbon steels
(1055 etc.) AH120 (2) 550 - 750 16 - 22 13 - 17
< 300 HB
AH120 (3) 425 - 625 8 - 12 6 - 10

AH120 (1) 425 - 625 14 - 20 11 - 16

Alloy steels
AH120 (2) 500 - 690 14 - 20 11 - 16
(4140, 4340)
< 300 HB
AH120 (3) 360 - 560 7 - 11 5-9

Profile Milling
AH120 (1) 360 - 560 12 - 18 10 - 15
Die steels
(H13,P20 etc.) AH120 (2) 425 - 625 12 - 18 10 - 14
< 300 HB
AH120 (3) 295 - 500 6 - 10 5-8

AH120 (1) 550 - 750 20 - 27 16 - 21

Cast irons
(JIS CLASS 25-40) AH120 (2) 625 - 820 20 - 27 16 - 21

AH120 (3) 500 - 690 12 - 20 9 - 13

AH120 (1) 230 - 360 6 - 10 5-8

Hardened steels
Prehardened steels AH120 (2) 260 - 400 6 - 10 5-8
< A980
AH120 (3) 160 - 300 3-6 2-5
Notes:
• Cutting speeds shown in the left table are of the most outer diameter of the tool.
• The values of the cutting speeds and feeds shown in the table are of under general cutting conditions. The values should be modified depending on the power
and rigidity of the machine to be used, and work holding conditions.
• When using the long shank type, the depth of cut, pick feed, cutting speed, and table feed should be reduced to 70 %-90 % of the values shown in the tables.

Machining types
(2) Shouldering at (3) Shouldering at
(1) Grooving
shallow depth of cut deep depth of cut

Tungaloy D165
 EB D
I n d ex a b l e b a l l - no se end m i l l f o r ro ug hi ng

rε

øDc

ø50.8
R
ap

øDsh6
100
Lf Rs
L
Fig. A Fig. B Combination shank
Metric Max. ap øDc z øDs ℓs Lf L rε Fig. Insert for R Insert for P
EBD040SSE 45 40 4 (7) 42 100 100 200 20 A ZDMT4005-MJ SCMT09T308-23
EBD040MSE 45 40 4 (7) 42 100 150 250 20 A ZDMT4005-MJ SCMT09T308-23
EBD050SSE 59 50 4 (7) 42 100 100 200 25 A ZDMT5006-MJ SCMT120408-23
EBD050MSE 59 50 4 (7) 42 100 150 250 25 A ZDMT5006-MJ SCMT120408-23
EBD050SCE 59 50 4 (7) 50.8 100 100 200 25 B ZDMT5006-MJ SCMT120408-23
EBD050MCE 59 50 4 (7) 50.8 100 150 250 25 B ZDMT5006-MJ SCMT120408-23

SPARE PARTS
Designation Clamping screw Lubricant Wrench
EBD040*SE CSTB-4M M-1000 T-15T
EBD050**E CSTB-5 M-1000 T-20T

INSERT
ZD M T-M J ( Fo r R - e d g e ) S C M T-2 3 ( Fo r p er ip h eral ed g e )
T rε T
A

7º
7º
A

P Steel 
M Stainless
K Cast iron 
N Non-ferrous
Profile Milling

S Superalloys : First choice

H Hard materials  : Second choice
Coated
AH120

Designation rε A T

ZDMT4005-MJ - z 0.512 0.217

ZDMT5006-MJ - z 0.638 0.256
SCMT09T308-23 0.031 z 0.375 0.156
SCMT120408-23 0.031 z 0.500 0.187
z: Line up

D166 www.tungaloyamerica.com
BB B 2000
T- CBN b a l l e n d mi l l s

L
L3

øDs
øDc
R

R
Metric BX850 z R øDc ℓ L3 L øDs
BBB2006 z 2 0.3 0.6 0.5 1.2 50 6
BBB2008 z 2 0.4 0.8 0.6 1.6 50 6
BBB2010 z 2 0.5 1 0.7 2 50 6
BBB2020 z 2 1 2 1.5 4 50 6

z: Line up

Tolerance (BBB2000)
R R Tolerance Tolerance on shank

0.3 - 1.0 ±0.005 h6

STA NDA RD CUT TING CONDITIONS

Ball radius (R)
No. of 0.3 0.4 0.5 1
Hard- revolutions Depth of cut
ISO Workpiece material Depth of cut Depth of cut Depth of cut
ness
n (min-1) ap × pf
Feed rate
ap × pf
Feed rate
ap × pf
Feed rate
ap × pf
Feed rate
(mm) (mm/min) (mm) (mm/min) (mm) (mm/min) (mm) (mm/min)

Prehardened steels
(NAK80, etc.)
~ 52 HRC 50,000 0.02 × 0.03 2,000 0.03 × 0.05 2,000 0.05 × 0.05 3,000 0.10 × 0.10 5,000
Die steels
(JIS SKD61, etc.)

Die steels
(JIS SKD11, ~ 62 HRC 50,000 0.01 × 0.02 2,000 0.02 × 0.03 2,000 0.03 × 0.05 3,000 0.05 × 0.05 5,000
DRM1 & 2, etc.)

High speed steel

Profile Milling
and die steel ~ 70 HRC 50,000 0.01 × 0.02 1,500 0.01 × 0.03 1,500 0.02 × 0.03 2,000 0.03 × 0.05 3,000
(JIS SKH, DRM3, etc.)

Notes:
• Depths of cut (ap) shown in the table are the allowable maximum values.
• Mist cooling or air blow is recommended.
• The maximum number of revolutions of the machine to be used is lower than 50,000 min-1,
the revolutions and feed rate should be modified at same rate.
• Use smallest possible overhang.

Ball radius (R) Inclined angle of workpiece (θ1) / Effective neck length (Z)
0.3 0°30 ź/1.25 1°/1.30 2°/1.35 3°/1.45
0.4 0°30 ź/1.65 1°/1.70 2°/1.80 3°/1.90
0.5 0°30 ź/2.05 1°/2.10 2°/2.25 3°/2.40
1 0°30 ź/4.15 1°/4.25 2°/4.50 3°/4.80

Tungaloy D167
MillLine - Multi-Functional Milling
Inch Metric

D170
R
Endmills with exchangeable heads for reduced
tool change time
ø0.236" - ø0.984" (ø6 mm - ø25 mm)

D2 0 0
R
Multi-functional endmills
ø0.393" - ø0.629"
max. ap 0.314"

D2 0 3
EVX R
Multi-functional endmills in larger diameters
ø0.629" - ø2.480" (ø16 mm - ø63 mm)
max. ap 0.59" (ø15 mm)

ECC D2 0 6
Chamfering endmills for large lengths
ø1.338" - ø2.165" (ø34 mm - ø55 mm)

ECP D2 0 8
Chamfering endmills for small lengths
ø0.394" - 1.417" (10 mm - ø36 mm)

TCB R R
D2 0 9
Counter boring tool for flat bottom finish
ø14 mm - ø43 mm

Thread Milling D211

Threading tool with a single indexable insert
M28 - M90

D168 www.tungaloyamerica.com
Tu n g M e i s te r

Tungaloy D169
Multi Function Features
The most effective tooling solution with the option
of hundreds of tools!
Tool changeover times can be measurably
reduced!
 Reduces tool changeover times  Highly accurate repeatability
drastically!!
z Accuracy can be maintained
z Machine downtime is decreased considerably. by touching the taper and
z Enables users to only change cutting head, simplifying face.
set-ups

Increases productivity by 90%

Exchange Time / Piece
less than 1 minute
■ Head exchange accuracy
Solid endmill           10 minutes
Height: ± 0.0008"
Run out:
≤ 0.0008"
 The weight of the tool to be
Face Precision thread
disposed is reduced Taper

z Reduces tool disposal

 No regrinding cost
For example: ø0.50" / square endmill
z No laborious endmill regrinding required.
: OAL 0.80" weight 20 g
conventional solid endmill : OAL 3.00" weight 140 g

1Wide range of cutting heads

23 kinds of cutting heads are available. The
2 Three kinds of shank material
Users can choose the most suitable
head exchange is easy and highly accurate Flexible combinations combination according to the machining
with the precision thread. TungMeister can be parameters, length and rigidity required.

applied to all kinds

of endmill machining • Steel: For general purpose
applications. • Carbide: For highly accurate machining with
excellent rigidity
• Tungsten: Reduced chattering due to vibration
dampening capacity

Straight shank & neck

Straight shank & neck (carbide)

Straight shank & taper neck

Straight (for grooving)

D170 www.tungaloyamerica.com
Overview

Multi Function
Head
High Drilling
Head Square Ball Torodial Chamfering Slotting
Feed （Centering drill）

Appearance

Page D173 D182 D178 D181 D185 D188 D190

Shank
Shank Straight Weldon Straight Straight
Neck Straight Straight Taper （Slotting）

Appearance

Steel z z z z
Carbide z - z z
Tungsten z - z -
（with oil hole

Page D194 D194 D196 D197

Cutting performance
Work material: 304SS (200HB) Shank: VSS037L300S06US Machine: Horizontal CAT40
Head: VEE037L27R031-U04S06 （Straight shank & neck, steel） Holder: Collet chuck
(ø.375", square type, 4 flutes, Grade: AH725） Cutting fluids: Dry

Comparison of milling for stainless steels

Continues Cutting speed : Vc = 330 sfm
16.5 working Feed rate : fz = 0.003 ipt
Depth of cut : ap = 0.20"
13.0 Cutting width : ae = 0.060"
Cutting length (ft)

· Competitor A cutting edges fractured after 1.7

10.0
minutes of machining and a 38" cutting length.
Fracture · The TungMeister cutting edges are still able to cut
6.6 after 5 minutes of machining.

3.3

0
Competitor A

Comparison of milling surface on stainless steels

Cutting speed : Vc = 430 sfm
Feed rate : fz = 0.002 ipt
Depth of cut : ap = 0.20"
Cutting width : ae = 0.080"

· When machining tough stainless steel the burr

created by the TungMeister is minimal. However,
Large
burr competitor A has a large burr when working under
the same conditions.
Competitor A

Tungaloy D171
 Designation system
Multi Function

Shank

V SS D10 L070 S 06 - W - A
1 2 3 4 5 6 7 8

1 Series 3 Shank diameter (mm) 4 Length (mm) 7 Shank material

V TungMeister D08 ø8 L070 70 S Steel
D10 ø10 C Carbide
2 Shank type D12 ø12 5 Shape of shank W Tungsten
D16 ø16 S Cylindrical
SS Straight neck
D20 ø20 W Weldon 8 Additional feature
TS Taper neck
D25 ø25 A with coolant hole
SC Slotting
D32 ø32 6 Connection screw size
ST for T-Slotting Thread size
VSC, VAD type 05 S05 M
AD TungFlex adapter (TungFlex adapters)
100 ø10 06 S06
120 ø12 08 S08
130 ø13 10 S10
180 ø18 12 S12
210 ø21 15 S15

Head
Square endmill

V E E 080 L05.0 R00 - 03 S05

1 2 3 4 5 6 7 8 9

Ball nose endmill

V B D 200 L15.0 - BG - 04 S12

1 2 3 4 5 6 7 8 9

1 Series 3 Helix angle / Rake face 6 Corner shape / Angle 7 Additional feature
V TungMeister B 0° Nose radius I Irregular pitch
C 15° R00 Sharp edge A for aluminum
2 Cutting edge D 30° R005 R0.05 R for roughing
E Square E 38° - 50° R01 R0.1 C Combined edge
B Ball F 60° R05 R0.5
R Radius T Land R10 R1.0 The number of flutes
8
FX for high feed Chamfer type General
CA for chamfering C15 0.15 x 45° 02 2
4 Diameter (mm)
CP Spot drilling C30 0.3 x 45° 06 6
060 ø6
for chamfering C60 0.6 x 45° Grooving head VST type
CW 200 ø20
(front and back) Chamfering head 3 3
A30 30° 4 4
CR for R chamfering 5 Cutting edge
length (mm) A60 60°
GC for counter boring R chamfering head
DP for center drilling Length
R10 R1.0 9 Connection screw size
S for slotting L07.0 7
R16 R1.6 S05 S05
T for T-slot milling L15.0 15
Ball nose S06 S06
Groove width
SG Sphere / high precision S08 S08
W1.50 1.5
BM Ball / general purpose S10 S10
W1.57 1.57
BG Ball / high precision S12 S12
W10.0 10
S15 S15

D172 www.tungaloyamerica.com
VE E **-03. . .

Multi Function
Tun g M e i s te r s q uare head w i t h 3 f l utes f o r g e n e ra l p u r p os e
r S

øDch6

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r S L Wrench Torque*

VEE031L20R000-U03S05 z 3 45° 0.312 0.300 0.200 0 S05 0.390 KEYV-S05 5.16
VEE037L27R000-U03S06 z 3 45° 0.375 0.370 0.270 0 S06 0.512 KEYV-S06 5.16
VEE050L37R000-U03S08 z 3 45° 0.500 0.453 0.370 0 S08 0.650 KEYV-S08 5.16
*Torque: Recommended torque (lbf·ft) for clamping. Packing quantity = 2 pcs.
z: Line up

VE D **-04. . . , VEE**- 04...

Tun g M e i s te r s q uare head w i t h 4 f l utes f o r g e n e ra l p u r p os e s
r S

øDce8

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r S L Wrench Torque*

VEE025L20R000-U04S05 z 4 45° 0.250 0.300 0.200 0.000 S05 0.390 KEYV-S05 5.16
VED031L20R015-U04S05 z 4 30° 0.312 0.300 0.200 0.015 S05 0.390 KEYV-S05 5.16
VED031L20R031-U04S05 z 4 30° 0.312 0.300 0.200 0.031 S05 0.390 KEYV-S05 5.16
VED031L20R062-U04S05 z 4 30° 0.312 0.300 0.200 0.062 S05 0.390 KEYV-S05 5.16
VEE031L20R000-U04S05 z 4 45° 0.312 0.300 0.200 0.000 S05 0.390 KEYV-S05 5.16
VEE031L20R015-U04S05 z 4 45° 0.312 0.300 0.200 0.015 S05 0.390 KEYV-S05 5.16
VEE031L20R031-U04S05 z 4 45° 0.312 0.300 0.200 0.031 S05 0.390 KEYV-S05 5.16 Square
VEE031L20R062-U04S05 z 4 45° 0.312 0.300 0.200 0.062 S05 0.390 KEYV-S05 5.16
VED037L27R015-U04S06 z 4 30° 0.375 0.370 0.275 0.015 S06 0.512 KEYV-S06 7.38
VED037L27R031-U04S06 z 4 30° 0.375 0.370 0.275 0.031 S06 0.512 KEYV-S06 7.38
VEE037L27R000-U04S06 z 4 45° 0.375 0.370 0.275 0.000 S06 0.512 KEYV-S06 7.38
VEE037L27R015-U04S06 z 4 45° 0.375 0.370 0.275 0.015 S06 0.512 KEYV-S06 7.38
VEE037L27R031-U04S06 z 4 45° 0.375 0.370 0.275 0.031 S06 0.512 KEYV-S06 7.38
VEE037L27R062-U04S06 z 4 45° 0.375 0.370 0.275 0.062 S06 0.512 KEYV-S06 7.38
VEE037L47R000-U04S06 z 4 45° 0.375 0.370 0.470 0.000 S06 0.810 KEYV-S06 7.38
VED050L37R015-U04S08 z 4 30° 0.500 0.453 0.374 0.015 S08 0.650 KEYV-S08 11.06
VED050L37R031-U04S08 z 4 30° 0.500 0.453 0.374 0.031 S08 0.650 KEYV-S08 11.06
VEE050L37R000-U04S08 z 4 45° 0.500 0.453 0.374 0.000 S08 0.650 KEYV-S08 11.06
VEE050L37R015-U04S08 z 4 45° 0.500 0.453 0.374 0.015 S08 0.650 KEYV-S08 11.06
VEE050L37R031-U04S08 z 4 45° 0.500 0.453 0.374 0.031 S08 0.650 KEYV-S08 11.06
VEE050L37R062-U04S08 z 4 45° 0.500 0.453 0.374 0.062 S08 0.650 KEYV-S08 11.06
VED062L47R015-U04S10 z 4 30° 0.625 0.600 0.470 0.015 S10 0.810 KEYV-S10 20.65
VED062L47R031-U04S10 z 4 30° 0.625 0.600 0.470 0.031 S10 0.810 KEYV-S10 20.65
VED062L47R062-U04S10 z 4 30° 0.625 0.600 0.470 0.062 S10 0.810 KEYV-S10 20.65
VEE062L47R000-U04S10 z 4 45° 0.625 0.600 0.470 0.000 S10 0.810 KEYV-S10 20.65
VEE062L47R031-U04S10 z 4 45° 0.625 0.600 0.470 0.031 S10 0.810 KEYV-S10 20.65
VED075L62R015-U04S12 z 4 30° 0.750 0.720 0.620 0.015 S12 1.000 KEYV-S12 20.65
VED075L62R031-U04S12 z 4 30° 0.750 0.720 0.620 0.031 S12 1.000 KEYV-S12 20.65
VED075L62R062-U04S12 z 4 30° 0.750 0.720 0.620 0.062 S12 1.000 KEYV-S12 20.65
VEE075L62R000-U04S12 z 4 45° 0.750 0.720 0.620 0.000 S12 1.000 KEYV-S12 20.65
VEE075L62R031-U04S12 z 4 45° 0.750 0.720 0.620 0.031 S12 1.000 KEYV-S12 20.65
VEE100L87R000-U04S15 z 4 45° 1.000 0.957 0.866 0.000 S15 1.457 KEYV-W20 29.50
VED100L87R015-U04S15 z 4 30° 1.000 0.957 0.866 0.015 S15 1.457 KEYV-W20 29.50
VED100L87R031-U04S15 z 4 30° 1.000 0.957 0.866 0.031 S15 1.457 KEYV-W20 29.50
VED100L87R062-U04S15 z 4 30° 1.000 0.957 0.866 0.062 S15 1.457 KEYV-W20 29.50
VED100L87R125-U04S15 z 4 30° 1.000 0.957 0.866 0.125 S15 1.457 KEYV-W20 29.50
*Torque: Recommended torque (lbf·ft) for clamping. VED/VEE025 - 075: Packing quantity = 2 pcs. VED/VEE100: Packing quantity = 1 pc. z: Line up
Reference pages
Standard cutting conditions → D179 - D180
Tungaloy D173
 V E E **-03. . .
Multi Function
Tu n g M e i s te r s q uare head w i t h 3 f l utes f o r ke y w a y

r S

øDch6

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Metric AH725 z Helx øDc ød1 Max. ap r S L Wrench Torque*

VEE077L04.0R02-03S05 z 3 38° 7.7 7.7 4 0.2 S05 10 KEYV-S05 7
VEE097L05.0R03-03S06 z 3 38° 9.7 9.7 5 0.3 S06 13 KEYV-S06 10
VEE117L07.0R03-03S08 z 3 38° 11.7 11.7 7 0.3 S08 16.5 KEYV-S08 15
VEE157L08.0R03-03S10 z 3 38° 15.7 15.3 8 0.3 S10 20.5 KEYV-S10 28
VEE197L12.0R04-03S12 z 3 38° 19.7 18.3 12 0.4 S12 25.5 KEYV-S12 28

*Torque: Recommended torque (N∙m) for clamping. z: Line up

Packing quantity = 2 pcs.

V E E **I . . .
Tu n g M e i s te r s q uare head w i t h i r reg ul ar p i t c h f l u te f or c h a t te r f re e c u t t i n g

S ƴ1 ƴ2
øDce8

ød1

ap ƴ2 ƴ1
r, C
L
ap = Max. depth of cut,
ƴ1 = ƴ2 S = Connection screw size

Square Inch AH725 z Helx øDc ød1 Max. ap r C S L Wrench Torque*

VEE031L20C012IU04S05 z 4 38° 0.312 0.300 0.200 - 0.012 S05 0.390 KEYV-S05 5.16
VEE037L27C016IU04S06 z 4 38° 0.375 0.370 0.270 - 0.016 S06 0.510 KEYV-S06 7.38
VEE050L37C020IU04S08 z 4 38° 0.500 0.480 0.370 - 0.020 S08 0.650 KEYV-S08 11.06
VEE062L47C016IU05S10 z 5 38° 0.625 0.600 0.470 - 0.016 S10 0.810 KEYV-S10 20.65
VEE075L62C024IU04S12 z 4 38° 0.750 0.720 0.620 - 0.024 S12 1.000 KEYV-S12 20.65
VEE100L87C024IU04S15 z 4 38° 1.000 0.941 0.866 - 0.024 S15 1.457 KEYV-W20 29.50
VEE100L87R000IU04S15 z 4 38° 1.000 0.941 0.866 0.000 - S15 1.457 KEYV-W20 29.50
VEE100L87R015IU04S15 z 4 38° 1.000 0.941 0.866 0.015 - S15 1.457 KEYV-W20 29.50
VEE100L87R031IU04S15 z 4 38° 1.000 0.941 0.866 0.031 - S15 1.457 KEYV-W20 29.50
VEE100L87R062IU04S15 z 4 38° 1.000 0.941 0.866 0.062 - S15 1.457 KEYV-W20 29.50
VEE100L87R125IU04S15 z 4 38° 1.000 0.941 0.866 0.125 - S15 1.457 KEYV-W20 29.50

*Torque: Recommended torque (lbf·ft) for clamping. z: Line up

VEE031 - VEE075: Packing quantity = 2 pcs.
VEE100: Packing quantity = 1pc.

Reference pages
Standard cutting conditions → D179 - D180

D174 www.tungaloyamerica.com
VE E **R . . .

Multi Function
Tun g M e i s te r s q uare head w i t h ser rated ed g e s f or rou gh i n g

S
ƴº

øDce9

ød1
C ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap C S L α˚ Wrench Torque*

VEE031L20C012RU04S05 z 4 45° 0.312 0.300 0.200 0.012 S05 0.390 90 KEYV-S05 5.16
VEE037L27C012RU04S06 z 4 45° 0.375 0.360 0.270 0.012 S06 0.512 90 KEYV-S06 7.38
VEE050L37C016RU04S08 z 4 45° 0.500 0.453 0.370 0.016 S08 0.650 90 KEYV-S08 11.06
VEE062L47C024RU05S10 z 5 45° 0.625 0.600 0.470 0.024 S10 0.800 7 KEYV-S10 20.65
VEE075L62C024RU06S12 z 6 45° 0.750 0.720 0.620 0.024 S12 1.000 3 KEYV-S12 20.65
VEE100L87C024RU06S15 z 6 45° 1.000 0.941 0.866 0.024 S15 1.457 3 KEYV-W20 29.50
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
VEE031 - VEE075: Packing quantity = 2 pcs.
VEE100: Packing quantity = 1pc.

VE E **C . . .
Tun g M e i s te r s q uare head w i t h co m b i ned ed ge s of f i n i s h a n d s e r ra te d

S
øDce9

ap ød1
C
L Square
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap C S L Wrench Torque*

VEE031L20C012CU04S05 z 4 45° 0.312 0.300 0.200 0.012 S05 0.390 KEYV-S05 5.16
VEE037L27C012CU04S06 z 4 45° 0.375 0.360 0.270 0.012 S06 0.510 KEYV-S06 7.38
VEE050L37C016CU04S08 z 4 45° 0.500 0.480 0.369 0.016 S08 0.650 KEYV-S08 11.06
VEE062L47C024CU04S10 z 4 45° 0.625 0.600 0.470 0.024 S10 0.800 KEYV-S10 20.65
VEE075L62C024CU04S12 z 4 45° 0.750 0.720 0.620 0.024 S12 1.000 KEYV-S12 20.65
VEE100L87C024CU04S15 z 4 45° 1.000 0.941 0.866 0.024 S15 1.457 KEYV-W20 29.50
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
VEE031 - VEE075: Packing quantity = 2 pcs.
VEE100: Packing quantity = 1pc.

Reference pages
Standard cutting conditions → D179 - D180

Tungaloy D175
 Multi Function V E E **A02. . .
Tu n g M e i s te r s q uare head w i t h 2 f l utes f o r a l u m i n u m m a c h i n i n g

r
S

øDch6

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Inch KS15F z Helx øDc ød1 Max. ap r S L Wrench Torque*

VEE037L27R000AU02S06 z 2 45° 0.375 0.360 0.270 0.000 S06 0.510 KEYV-S06 7.38
VEE037L27R020AU02S06 z 2 45° 0.375 0.360 0.270 0.020 S06 0.510 KEYV-S06 7.38
VEE050L37R000AU02S08 z 2 45° 0.500 0.480 0.370 0.000 S08 0.650 KEYV-S08 11.06
VEE050L37R020AU02S08 z 2 45° 0.500 0.480 0.370 0.020 S08 0.650 KEYV-S08 11.06
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

V E E **A03. . .
Tu n g M e i s te r s q uare head w i t h 3 f l utes f o r a l u m i n u m m a c h i n i n g

r S
øDch6

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Square Inch KS15F z Helx øDc ød1 Max. ap r S L Wrench Torque*

VEE031L20R020AU03S05 z 3 45° 0.312 0.300 0.200 0.020 S05 0.390 KEYV-S05 5.16
VEE037L20R031AU03S06 z 3 45° 0.375 0.360 0.230 0.031 S06 0.510 KEYV-S06 7.38
VEE037L20R062AU03S06 z 3 45° 0.375 0.360 0.230 0.062 S06 0.510 KEYV-S06 7.38
VEE050L31R031AU03S08 z 3 45° 0.500 0.480 0.310 0.031 S08 0.650 KEYV-S08 11.06
VEE050L31R062AU03S08 z 3 45° 0.500 0.480 0.310 0.062 S08 0.650 KEYV-S08 11.06
VEE050L31R094AU03S08 z 3 45° 0.500 0.480 0.310 0.094 S08 0.650 KEYV-S08 11.06
VEE050L31R125AU03S08 z 3 45° 0.500 0.480 0.310 0.125 S08 0.650 KEYV-S08 11.06
VEE062L39R000AU03S10 z 3 45° 0.625 0.600 0.390 0.000 S10 0.810 KEYV-S10 20.65
VEE062L39R031AU03S10 z 3 45° 0.625 0.600 0.390 0.031 S10 0.810 KEYV-S10 20.65
VEE062L39R062AU03S10 z 3 45° 0.625 0.600 0.390 0.062 S10 0.810 KEYV-S10 20.65
VEE062L39R094AU03S10 z 3 45° 0.625 0.600 0.390 0.094 S10 0.810 KEYV-S10 20.65
VEE062L39R125AU03S10 z 3 45° 0.625 0.600 0.390 0.125 S10 0.810 KEYV-S10 20.65
VEE075L47R062AU03S12 z 3 45° 0.750 0.720 0.470 0.062 S12 1.000 KEYV-S12 20.65
VEE075L47R094AU03S12 z 3 45° 0.750 0.720 0.470 0.094 S12 1.000 KEYV-S12 20.65
VEE075L47R125AU03S12 z 3 45° 0.750 0.720 0.470 0.125 S12 1.000 KEYV-S12 20.65
VEE075L50R008AU03S12 z 3 45° 0.750 0.720 0.500 0.008 S12 1.000 KEYV-S12 20.65
VEE075L50R020AU03S12 z 3 45° 0.750 0.720 0.500 0.020 S12 1.000 KEYV-S12 20.65
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D179 - D180

D176 www.tungaloyamerica.com
VE D **-06. . . , VEE**- 06...

Multi Function
Tun g M e i s te r s q uare head w i t h 6 f l utes f o r d i f f i c u l t - to- c u t m a te r i a l m a c h i n i n g

S
≤5°

øDce8

ød1
r,C ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 AH750 z Helx øDc ød1 Max. ap r C S L Wrench Torque*

VED031L20R015-U06S05 z 6 30° 0.312 0.300 0.200 0.015 - S05 0.390 KEYV-S05 5.16
VEE031L20R000-U06S05 z 6 45° 0.312 0.300 0.200 0.000 - S05 0.390 KEYV-S05 5.16
VEE031L20R031-U06S05 z 6 45° 0.312 0.300 0.200 0.031 - S05 0.390 KEYV-S05 5.16
VEE031L20C004-U06S05 z 6 50° 0.312 0.300 0.200 - 0.004 S05 0.390 KEYV-S05 5.16
VED037L27R015-U06S06 6 30° 0.375 0.370 0.275 0.015 - S06 0.512 KEYV-S06 7.38
VED037L27R031-U06S06 z 6 30° 0.375 0.370 0.275 0.031 - S06 0.512 KEYV-S06 7.38
VEE037L27R000-U06S06 z 6 45° 0.375 0.370 0.275 0.000 - S06 0.512 KEYV-S06 7.38
VEE037L27R015-U06S06 z 6 45° 0.375 0.370 0.275 0.015 - S06 0.512 KEYV-S06 7.38
VEE037L27R031-U06S06 z 6 45° 0.375 0.370 0.275 0.031 - S06 0.512 KEYV-S06 7.38
VEE037L27R062-U06S06 z 6 45° 0.375 0.370 0.275 0.062 - S06 0.512 KEYV-S06 7.38
VEE037L27C004-U06S06 z 6 50° 0.375 0.370 0.275 - 0.004 S06 0.510 KEYV-S06 7.38
VED050L37R015-U06S08 z 6 30° 0.500 0.453 0.374 0.015 - S08 0.650 KEYV-S06 7.38
VED050L37R031-U06S08 z 6 30° 0.500 0.453 0.374 0.031 - S08 0.650 KEYV-S08 11.06
VEE050L37R000-U06S08 z 6 45° 0.500 0.453 0.374 0.000 - S08 0.650 KEYV-S08 11.06
VEE050L37R015-U06S08 z 6 45° 0.500 0.453 0.374 0.015 - S08 0.650 KEYV-S08 11.06
VEE050L37R031-U06S08 z 6 45° 0.500 0.453 0.374 0.031 - S08 0.650 KEYV-S08 11.06
VEE050L37R062-U06S08 z 6 45° 0.500 0.453 0.374 0.062 - S08 0.650 KEYV-S08 11.06
VEE050L37C004-U06S08 z 6 50° 0.500 0.453 0.374 - 0.004 S08 0.650 KEYV-S08 11.06
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

Square
VE D **-08, 10. . . , V EE**- 08,10...
Tun g M e i s te r s q uare head w i t h 8 , 1 0 f l utes f or d i f f i c u l t - to- c u t m a te r i a l m a c h i n i n g

S
≤ 5°
øDce8

ød1

ap
r, C
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 AH750 z Helx øDc ød1 Max. ap r C S L Wrench Torque*

VED062L47R000-U08S10 z 8 30° 0.625 0.600 0.470 0.000 - S10 0.810 KEYV-S10 20.65
VED062L47R015-U08S10 z 8 30° 0.625 0.600 0.470 0.015 - S10 0.810 KEYV-S10 20.65
VED062L47R031-U08S10 z 8 30° 0.625 0.600 0.470 0.031 - S10 0.810 KEYV-S10 20.65
VED062L47R062-U08S10 z 8 30° 0.625 0.600 0.470 0.062 - S10 0.810 KEYV-S10 20.65
VEE062L47C008-U08S10 z 8 45° 0.625 0.600 0.470 - 0.008 S10 0.810 KEYV-S10 20.65
VED075L62R031-U10S12 z 10 30° 0.750 0.720 0.620 0.031 - S12 1.000 KEYV-S12 20.65
VED075L62R062-U10S12 z 10 30° 0.750 0.720 0.620 0.062 - S12 1.000 KEYV-S12 20.65
VEE075L62C008-U10S12 z 10 45° 0.750 0.720 0.620 - 0.008 S12 1.000 KEYV-S12 20.65
VED100L87R031-U10S15 z 10 30° 1.000 0.941 0.866 0.031 - S15 1.457 KEYV-W20 29.50
VED100L87R062-U10S15 z 10 30° 1.000 0.941 0.866 0.062 - S15 1.457 KEYV-W20 29.50
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
VEE/VED062 - 075: Packing quantity = 2 pcs.
VED100: Packing quantity = 1pc.

Reference pages
Standard cutting conditions → D179 - D180

Tungaloy D177
 Multi Function V R B **-02. . .
Tu n g M e i s te r ra d i us head w i t h 2 p ressed f l u te s

˺c˚ S
R

øDch9

ød1
r ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r θc° S L Wrench Torque*

VRB062L31R187-U02S10 z 2 0° 0.625 0.600 0.310 0.187 0.197 S06 0.580 KEYV-S06 7.38
VRB075L45R250-U02S12 z 2 0° 0.750 0.720 0.450 0.250 0.197 S06 0.680 KEYV-S06 7.38
VRB075L45R312-U02S12 z 2 0° 0.750 0.720 0.450 0.312 0.276 S06 0.680 KEYV-S06 7.38

Note: Suitable for contouring operation. Some heads require different wrench sizes. z: Line up
*Torque: Recommended torque (lbf·ft) for clamping.
Packing quantity = 2 pcs.

V R D **-06. . .
Tu n g M e i s te r ra d i us head w i t h 6 g ro und f l u te s

7° S R
øDce8

≤ 9°
ød1
r ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r S L Wrench Torque*

VRD031L16R078-U06S05 z 6 30° 0.312 0.300 0.160 0.078 S05 0.390 KEYV-S05 5.16
VRD037L19R031-U06S06 z 6 30° 0.375 0.360 0.190 0.031 S06 0.510 KEYV-S06 7.38
R VRD037L19R062-U06S06 z 6 30° 0.375 0.360 0.190 0.062 S06 0.510 KEYV-S06 7.38

Radius
VRD037L19R125-U06S06 z 6 30° 0.375 0.360 0.190 0.125 S06 0.510 KEYV-S06 7.38
VRD050L27R062-U06S08 z 6 30° 0.500 0.480 0.270 0.062 S08 0.650 KEYV-S08 11.06
VRD050L27R125-U06S08 z 6 30° 0.500 0.480 0.270 0.125 S08 0.650 KEYV-S08 11.06
VRD050L27R156-U06S08 z 6 30° 0.500 0.480 0.270 0.156 S08 0.650 KEYV-S08 11.06
VRD062L35R200-U06S10 z 6 30° 0.625 0.600 0.350 0.200 S10 0.807 KEYV-S10 20.65

*Torque: Recommended torque (lbf·ft) for clamping. z: Line up

Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D179 - D180

D178 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Shoulder milling (VEE: 3 flutes, VED/VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VEE-C, VRB, VRC, VRD)

Multi Function
Cutting Feed per tooth: fz (ipt) Depth of
Workpiece material Hard- Pick feed
ISO speed Tool diameter: øDc (in) cut
ness P f (in)
Vc (sfm) 0.250" 0.312" 0.375" 0.500" 0.625" 0.750" 1.000" ap (in)

Low carbon steels 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
1045, 1055, etc.
- 300 HB 260 - 590 0.003 0.004 0.005 0.005 0.006 0.007 0.007 0.25 x øDc
øDc

0.6 x
- 300 HB 200 - 460 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -
High carbon steels
0.25 x øDc
4140, 5120, etc. 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

30 - 40 0.6 x
Prehardened steel 200 - 400 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.25 x øDc
PX5, NAK80, etc. HRC 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

Stainless steels 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
S30400, S31600, etc.
- 200 HB 130 - 330 0.003 0.004 0.005 0.005 0.006 0.007 0.007 0.25 x øDc
øDc

Grey cast irons 150 - 250 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
260 - 660 0.003 0.004 0.005 0.25 x øDc
No.250B, No.300B, etc. HB 0.005 0.006 0.007 0.007 øDc

Ductile cast irons 150 - 250 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
60-40-18, etc. 260 - 660 0.003 0.004 0.005 0.005 0.006 0.007 0.007 0.25 x øDc
HB Dc

Aluminum alloys 0.6 x

Si < 13% - 660 - 2297 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.25 x øDc
0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

Aluminum alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
Si *13% - 330 - 980 0.003 0.004 0.005 0.005 0.006 0.007 0.007 0.25 x øDc
øDc

0.6 x
130 - 260 0.001
Titanium alloys - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -
- 0.05 x øDc
Ti-6Al-4V, etc. 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

Heat-resistant alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
- 66 - 130 0.05 x øDc
Inconel 718, etc. 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

40 - 50 0.6 x
130 - 260 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -
Hardened steel
0.05 x øDc
H13, etc. HRC 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

Hardened steel 50 - 60 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 - 0.6 x
D2, etc. 66 - 200 0.05 x øDc
HRC 0.003 0.004 0.005 0.005 0.006 0.007 0.007 øDc

Slot milling (VEE: 3 flutes, VED/VEE: 4 flutes, VEE-A, VEE-I, VEE-R, VEE-C, VRB, VRC, VRD)
Feed per tooth: fz (ipt)
Workpiece material Hardness Cutting Depth of
ISO speed Tool diameter: øDc (in) cut Square
Vc (sfm) 0.250" 0.312" 0.375" 0.500" 0.625" 0.750" 1.000" ap (in)

Low carbon steels 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 - R
1045, 1055, etc. - 300 HB 260 - 590 0.003 0.004 0.005 0.005 0.006 0.007 0.5 x øDc
0.004 Radius

High carbon steels 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -
4140, 5120, etc. - 300 HB 200 - 460 0.5 x øDc
0.003 0.004 0.005 0.005 0.006 0.007 0.004

Prehardened steel 30 - 40 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

PX5, NAK80, etc. 200 - 400 0.5 x øDc
HRC 0.003 0.004 0.005 0.005 0.006 0.007 0.004

Stainless steels 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

S30400, S31600, etc. - 200 HB 130 - 330 0.003 0.004 0.005 0.005 0.006 0.007 0.5 x øDc
0.004

Grey cast irons 150 - 250 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -
No.250B, No.300B, etc. 260 - 660 0.5 x øDc
HB 0.003 0.004 0.005 0.005 0.006 0.007 0.004

Ductile cast irons 150 - 250 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -
60-40-18, etc. 260 - 660 0.5 x øDc
HB 0.003 0.004 0.005 0.005 0.006 0.007 0.004

Aluminum alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

Si < 13% - 660 - 2297 0.5 x øDc
0.003 0.004 0.005 0.005 0.006 0.007 0.004

Aluminum alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

Si *13% - 330 - 980 0.003 0.004 0.005 0.005 0.006 0.007 0.5 x øDc
0.004

Titanium alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

Ti-6Al-4V, etc. - 130 - 260 0.003 0.004 0.005 0.005 0.006 0.007 0.5 x øDc
0.004

Heat-resistant alloys 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

Inconel 718, etc. - 66 - 130 0.5 x øDc
0.003 0.004 0.005 0.005 0.006 0.007 0.004

Hardened steel 40 - 50 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

H13, etc. 130 - 260 0.003 0.004 0.005 0.005 0.006 0.007 0.2 x øDc
HRC 0.004

Hardened steel 50 - 60 0.001 - 0.001 - 0.003 - 0.003 - 0.004 - 0.004 - 0.003 -

D2, etc. 66 - 200 0.003 0.004 0.005 0.005 0.006 0.007 0.2 x øDc
HRC 0.004

Tungaloy D179
 STA NDA RD CUT TING CONDITIONS
Multi Function
Shoulder milling (VED / VEE: 6 flutes, VED / VEE: 8, 10 flutes)
Feed per tooth: fz (ipt)
Workpiece Cutting Depth of
ISO Hardness speed Tool diameter: øDc (in) cut Pick feed
material
Vc (sfm) 0.312" 0.375" 0.500" 0.625" 0.750" 1.000" ap (in) Pf (in)
Titanium alloys 0.002 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -
- 200 - 400 0.6 x øDc 0.02 x øDc
Ti-6Al-4V, etc. 0.004 0.005 0.005 0.006 0.007 0.007

Heat-resistant alloys 0.002 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -

- 100 - 200 0.6 x øDc 0.02 x øDc
Inconel 718, etc. 0.004 0.005 0.005 0.006 0.007 0.007

Hardened steel 40 - 50 0.002 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -

H13, H19, etc. 260 - 530 0.6 x øDc 0.02 x øDc
HRC 0.004 0.005 0.005 0.006 0.007 0.007

Hardened steel 50 - 60 0.002 - 0.003 - 0.003 - 0.004 - 0.004 - 0.004 -

130 - 300 0.6 x øDc 0.02 x øDc
D2, etc. HRC 0.004 0.005 0.005 0.006 0.007 0.007

Square

D180 www.tungaloyamerica.com
VFX**-02. . .

Multi Function
Tun g M e i s te r ra d i us head f o r sup er hi g h- f eed m i l l i n g

≤ 10°

øDch9

ød1
r ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r (1)

S L Wrench Torque*
VFX037L02R060-U02S06 z 2 0° 0.375 0.360 0.020 0.060 S06 0.490 KEYV-S06 7.38
VFX050L04R080-U02S08 z 2 0° 0.500 0.480 0.040 0.080 S08 0.590 KEYV-S08 11.06
VFX075L06R080-U02S12 z 2 0° 0.750 0.720 0.059 0.080 S12 0.685 KEYV-S10 20.65
(1) Corner radius for CAM programing z: Line up
Note: For VFX head, taper neck shank or Tungsten shank should be recommended.
*Torque: Recommended torque (lbf·ft) for clamping.
Packing quantity = 2 pcs.

STA NDA RD CUT TING CONDITIONS

High feed milling (VFX)
ø0.375" ø0.500" ø0.750"
Workpiece Cutting Width
ISO Hardness speed Feed per Depth of Feed per Depth of Feed per Depth of of cut
material Vc (sfm) tooth cut tooth cut tooth cut ae (in)
fz (ipt) ap (in) fz (ipt) ap (in) fz (ipt) ap (in)

Low carbon steels 0.012 - 0.016 - 0.024 -

- 300 HB 330 - 660 0.020 0.020 0.040 0.6 x øDc
1045, 1055, etc. 0.028 0.031 0.040

High carbon steels 0.008 - 0.012 - 0.020 -

4140, 5120, etc. - 300 HB 260 - 590 0.020 0.020 0.040 0.6 x øDc
0.024 0.028 0.035

Prehardened steel 0.008 - 0.008 - 0.012 -

30 - 40 HRC 260 - 530 0.016 0.016 0.030 0.6 x øDc
PX5, NAK80, etc. 0.020 0.02 0.024

Stainless steels 0.008 - 0.008 - 0.012 -

S30400, S31600, etc.
- 200 HB 200 - 330 0.016 0.016 0.030 0.6 x øDc
0.024 0.024 0.028

Grey cast irons 0.012 - 0.016 - 0.024 - R

No.250B, No.300B, etc.
150 - 250 HB 330 -720 0.020 0.030 0.040 0.6 x øDc
0.028 0.031 0.040
Radius

Ductile cast irons 0.008 - 0.012 - 0.020 -

60-40-18, etc.
150 - 250 HB 330 - 720 0.020 0.030 0.040 0.6 x øDc
0.024 0.028 0.035

Titanium alloys 0.008 - 0.008 - 0.008 -

- 130 - 260 0.016 0.016 0.020 0.25 x øDc
Ti-6Al-4V, etc. 0.020 0.020 0.024

Heat-resistant alloys 0.004 - 0.004 - 0.004 -

- 66 - 130 0.012 0.012 0.016 0.25 x øDc
Inconel 718, etc. 0.012 0.012 0.012

Hardened steel 0.008 - 0.008 - 0.012 -

H13, etc.
40 - 50 HRC 130 - 260 0.012 0.012 0.016 0.45 x øDc
0.016 0.016 0.020

Hardened steel 0.004 - 0.004 0.004 -

D2, etc.
50 - 60 HRC 66 - 200 0.008 0.008 0.012 0.25 x øDc
0.008 -0.008 0.012

Tungaloy D181
Multi Function V B B **-B M . . .
Tu n g M e i s te r bal l no se head w i t h p ressed e d ge f or rou gh i n g
S

øDch9

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap S L Wrench Torque*

VBB0312L20-BM-U02S05 z 2 0° 0.312 0.300 0.310 S05 0.390 KEYV-S05 5.16
VBB0375L27-BM-U02S06 z 2 0° 0.375 0.360 0.380 S06 0.478 KEYV-S06 7.38
VBB0500L37-BM-U02S08 z 2 0° 0.500 0.453 0.512 S08 0.646 KEYV-S08 11.06
VBB0625L47-BM-U02S10 z 2 0° 0.625 0.600 0.630 S10 0.750 KEYV-S10 20.65
• For roughing z: Line up
*Torque: Recommended torque (lbf·ft) for clamping.
Packing quantity = 2 pcs.

V B B **-B G . . .
Tu n g M e i s te r bal l no se head w i t h g ro und e d ge f or s e m i - f i n i s h i n g
S
øDch7

ød1
ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH750 z Helx øDc ød1 Max. ap S L Wrench Torque*

VBB0312L31-BG-U02S05 z 2 0° 0.312 0.300 0.312 S05 0.390 KEYV-S05 5.16
VBB0375L37-BG-U02S06 z 2 0° 0.375 0.360 0.380 S06 0.480 KEYV-S06 7.38
VBB0500L50-BG-U02S08 z 2 0° 0.500 0.480 0.500 S08 0.640 KEYV-S08 11.06
VBB0625L50-BG-U02S10 z 2 0° 0.625 0.598 0.630 S10 0.752 KEYV-S10 20.65
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

Ball V B D **-B G . . .
Tu n g M e i s te r bal l no se head w i t h 2 f l utes a n d h e l i c a l grou n d e d ge f or f i n i s h i n g

R S
øDce8

ød1

ap
L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap R S L Wrench Torque*

VBD0312L20-BG-U02S05 z 2 30° 0.312 0.300 0.200 0.156 S05 0.350 KEYV-S05 5.16
VBD0375L27-BG-U02S06 z 2 30° 0.375 0.360 0.275 0.188 S06 0.512 KEYV-S06 7.38
VBD0500L37-BG-U02S08 z 2 30° 0.500 0.453 0.374 0.249 S08 0.650 KEYV-S08 11.06
VBD0625L35-BG-U02S10 z 2 30° 0.625 0.600 0.470 0.313 S10 0.800 KEYV-S10 20.65
• The tolerance of R : (1) ± 0.0003" (2) ± 0.0004" z: Line up
*Torque: Recommended torque (lbf·ft) for clamping.
Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D184

D182 www.tungaloyamerica.com
VB D **-B G . . . , V BE**- BG ...

Multi Function
Tun g M e i s te r b a l l no se head w i t h 4 f l utes and h e l i c a l grou n d e d ge f or f i n i s h i n g
S ° S R S
VBER R 11.7 ° 11.7 VBD

øDce8

ød1
øDce8

øDce8

ød1

ød1
ap ap ap
L L L
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap R S L Wrench Torque*

VBE0250L20-BG-U04S05 z 4 45° 0.250 0.300 0.200 0.124 S05 0.390 KEYV-S05 5.16
VBE0312L20-BG-U04S05 z 4 30° 0.312 0.300 0.200 0.156 S05 0.350 KEYV-S05 5.16
VBD0375L27-BG-U04S06 z 4 30° 0.375 0.360 0.275 0.188 S06 0.512 KEYV-S06 7.38
VBD0500L37-BG-U04S08 z 4 30° 0.500 0.453 0.374 0.249 S08 0.650 KEYV-S08 11.06
VBD0625L47-BG-U04S10 z 4 30° 0.625 0.600 0.470 0.313 S10 0.800 KEYV-S10 20.65
VBD0750L62-BG-U04S12 z 4 30° 0.750 0.720 0.620 0.374 S12 1.000 KEYV-S12 20.65
VBD100L87-BG-U04S15 z 4 30° 1.000 0.941 0.866 0.499 S15 1.457 KEYV-W20 29.50
• The tolerance of R : (1) ± 0.0004 (2) ± 0.0005 (3) ± 0.0008 z: Line up
*Torque: Recommended torque (lbf·ft) for clamping.
VBE0250,0312/VBD0375 - 0750: Packing quantity = 2 pcs. VBD100: Packing quantity = 1pc.

VB B **-SG . . .
Tun g M e i s te r b a l l no se head w i t h sp her i cal de s i gn e d e d ge , a v a i l a b l e f or p u l l - c u t t i n g on t h e w a l l
ap
S
øDch7

ød1
120°
L ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap S L Wrench Torque**

VBB0375L30-SG-U02S05 z 2 0° 0.375 0.300 0.315 S05 0.389 KEYV-S05 5.16
VBB0500L40-SG-U02S06 z 2 0° 0.500 0.378 0.378 S06 0.480 *KEYV-S08 7.38
VBB0625L50-SG-U02S08 z 2 0° 0.625 0.480 0.508 S08 0.606 *KEYV-S10 11.06
VBB0750L60-SG-U02S10 z 2 0° 0.750 0.600 0.634 S10 0.710 KEYV-S10 20.65
• For pull-cutting on the vertical wall z: Line up
* Some heads require different size of wrench.
**Torque: Recommended torque (lbf·ft) for clamping. Packing quantity = 2 pcs.

Ball

VB E **-B G A. . .
Tun g M e i s te r b a l l no se head w i t h 2 f l utes and h e l i c a l grou n d e d ge f or A l m a c h i n i n g

R S
øDce8

ød1

ap
L
ap = Max. depth of cut, S = Connection screw size

Inch KS15F z Helx øDc ød1 Max. ap R S L Wrench Torque*

VBE0312L20-BGAU02S05 z 2 45° 0.312 0.300 0.200 0.156 S05 0.390 KEYV-S05 5.16
VBE0375L27-BGAU02S06 z 2 45° 0.375 0.360 0.270 0.187 S06 0.510 KEYV-S06 7.38
VBE0500L37-BGAU02S08 z 2 45° 0.500 0.480 0.370 0.249 S08 0.650 KEYV-S08 11.06
VBE0625L47-BGAU02S10 z 2 45° 0.625 0.600 0.470 0.312 S10 0.800 KEYV-S10 20.65
VBE0750L50-BGAU02S12 z 2 45° 0.750 0.720 0.500 0.374 S12 1.000 KEYV-S12 20.65
• The tolerance of R : (1) ± 0.0004 (2) ± 0.0005 z: Line up
*Torque: Recommended torque (lbf·ft) for clamping. Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D184

Tungaloy D183
 STA NDA RD CUT TING CONDITIONS
Multi Function
Standard cutting conditions: Profiling for roughing (VBB-BM / BG / SG, VBD-BG, VBE-BGA)
Cutting Feed per tooth: fz (ipt) Depth of Pick
Workpiece material Hard- speed Tool diameter: øDc (in) cut feed
ISO
ness ap (in) Pf (in)
Vc (sfm) 0.250" 0.312" 0.375" 0.500" 0.625" 0.750" 1.000"
0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
Low carbon steels - 200 328 - 656
0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

High carbon steels 200 - 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
262 - 591
Alloy steels 300 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

Prehardened steel 30 - 40 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
262 - 525
PX5, NAK80, etc. HRC 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

Stainless steels 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
- 197 - 328
304, 316, etc. 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

150 - 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
Grey cast irons 328 - 722
250 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

150 - 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
Ductile cast irons 328 - 722
250 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

Aluminum alloys 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.016 x
- 656 - 2297
(Si < 13%) 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.008 x

High temp alloy 55HRC 131 - 262
0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

150 - 0.001 - 0.002 - 0.002 - 0.002 - 0.003 - 0.003 - 0.003 - 0.012 x 0.008 x
High hardened steels 131 - 262
225 0.003 0.003 0.004 0.004 0.005 0.006 0.006 øDc øDc

Standard cutting conditions: Profiling for semi-finishing and finishing

(VBB-BM / BG / SG, VBD-BG, VBE-BGA)
Cutting Feed per tooth: fz (ipt) Depth of Pick
Workpiece material Hard- cut feed
ISO speed Tool diameter: øDc (in) ap (in)
ness Pf (in)
Vc (sfm) 0.250" 0.312" 0.375" 0.500" 0.625" 0.750" 1.000"
0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
Low carbon steels - 300 HB 394 - 820
0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

High carbon steels 0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
- 300 HB 328 - 722
Alloy steels 0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

30 - 40 0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x

Prehardened steel 328 - 656
HRC 0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc
Ball
0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
Stainless steels - 200 HB 262 - 394
0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

150 - 250 0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
Grey cast irons 394 - 919
HB 0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

150 - 250 0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
Ductile cast irons 394 -919
HB 0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

Aluminum alloys 0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.004 x 0.006 x
- 984 - 3281
(Si < 13%) 0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.003 x 0.004 x

High temp alloys - 164 - 328
0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

0.001 - 0.001 - 0.002 - 0.002 - 0.002 - 0.002 - 0.004 - 0.003 x 0.004 x

High hardened steels - 164 - 328
0.003 0.004 0.004 0.004 0.005 0.007 0.007 øDc øDc

D184 www.tungaloyamerica.com
VC P **-02. . .

Multi Function
Tun g M e i s te r h e a d w i t h 2 p ressed f l utes f o r s p ot d r i l l i n g a n d c h a m f e r i n g

øDcz9

ød1
ƴ°

140°
k
P angl b
ap
L
b = Max. hole depth, ap = Max. depth of cut, S = Connection screw size

Metric AH725 P angl z Helx øDc ød1 Max. ap b S L k ƴ˚ Wrench Torque*

VCP100L09.5A30-02S06 z 60° 2 0° 10 9.5 8.5 7.5 S06 11.75 1.5 30 KEYV-S06 10
VCP120L12.0A30-02S08 z 60° 2 0° 12 11.5 11 9.2 S08 15.4 1.5 30 KEYV-S08 15
VCP160L15.0A30-02S10 z 60° 2 0° 16 15.2 16 12 S10 20.2 2.5 30 KEYV-S10 28
VCP080L07.7A45-02S05 z 90° 2 0° 8 7.6 7.5 3.7 S05 9.75 1 45 KEYV-S05 7
VCP083L07.9A45-02S05 z 90° 2 0° 8.3 7.6 7.5 3.8 S05 10 1 45 KEYV-S05 7
VCP100L09.0A45-02S06 z 90° 2 0° 10 9.5 9.5 4.4 S06 11.75 1.5 45 KEYV-S06 10
VCP104L09.0A45-02S06 z 90° 2 0° 10.4 9.5 9.5 4.6 S06 11.75 1.5 45 KEYV-S06 10
VCP120L12.0A45-02S08 z 90° 2 0° 12 11.5 11.5 5.4 S08 15.4 1.5 45 KEYV-S08 15
VCP124L12.0A45-02S08 z 90° 2 0° 12.4 11.5 11.5 5.6 S08 15.4 1.5 45 KEYV-S08 15
VCP160L15.0A45-02S10 z 90° 2 0° 16 15.2 15 7.1 S10 18.8 1.5 45 KEYV-S10 28
VCP165L15.0A45-02S10 z 90° 2 0° 16.5 15.2 15 7.1 S10 18.8 1.5 45 KEYV-S10 28
VCP100L09.5A60-02S06 z 120° 2 0° 10 9.5 9.5 2.7 S06 12.7 1.5 60 KEYV-S06 10
VCP120L12.0A60-02S08 z 120° 2 0° 12 11.5 11.5 3.3 S08 15.2 1.5 60 KEYV-S08 15
VCP160L15.5A60-02S10 z 120° 2 0° 16 15.2 16 4.4 S10 19.9 1.5 60 KEYV-S10 28

•Min. chamfering: ø1.5 mm z: Line up

*Torque: Recommended torque (N∙m) for clamping.
Packing quantity = 2 pcs.

VD P **-02. . .
Tun g M e i s te r h e a d f o r center d r i l l i ng

L S
L1
øDc
120º

ød1

Ball
60º
S = Connection screw size

Metric AH725 z Helx øDc ød1 L1 S L Wrench Torque*

VDP328L04.6A30-02S05 z 2 0° 3.28 8 4.6 S05 15 KEYV-S05 7
VDP412L05.9A30-02S06 z 2 0° 4.12 10 5.9 S06 19 KEYV-S06 10
VDP513L07.2A30-02S08 z 2 0° 5.13 12 7.2 S08 23 KEYV-S08 15
VDP646L08.9A30-02S10 z 2 0° 6.46 16 8.9 S10 28 KEYV-S10 28

*Torque: Recommended torque (N∙m) for clamping. z: Line up

Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D186

Tungaloy D185
 STA NDA RD CUT TING CONDITIONS
Multi Function
Drilling (VCP, VDP)
Cutting Feed: f (ipr)
ISO Workpiece material Hardness speed
Vc (sfm) VDP328 VDP412 VDP513 VDP646 VCP
Low carbon steels 0.0016 - 0.0020 - 0.0020 - 0.0024 - 0.0024 -
- 300 HB 131 - 262
1045, 1055, etc. 0.0031 0.0039 0.0039 0.0047 0.0047
High carbon steels 0.0016 - 0.0020 - 0.0020 - 0.0024 - 0.0024 -
- 300 HB 98 - 164
4140,etc. 0.0031 0.0039 0.0039 0.0047 0.0047
Prehardened steel 30 - 40 0.0016 - 0.0020 - 0.0020 - 0.0024 - 0.0024 -
66 - 98
PX5, NAK80, etc. HRC 0.0031 0.0039 0.0039 0.0047 0.0047

Stainless steels 0.0016 - 0.0020 - 0.0020 - 0.0024 - 0.0024 -

- 200 HB 49 - 82
304, 316, etc. 0.0031 0.0039 0.0039 0.0047 0.0047

Grey cast irons 150 - 250 0.0020 - 0.0028 - 0.0028 - 0.0047 - 0.0047 -
197 - 328
250, 300, etc. HB 0.0035 0.0047 0.0047 0.0071 0.0071
Ductile cast irons 150 - 250 0.0016 - 0.0020 - 0.0020 - 0.0039 - 0.0039 -
197 - 328
400-15S, etc. HB 0.0031 0.0039 0.0039 0.0059 0.0059
Titanium alloys 0.0016 - 0.0016 - 0.0016 - 0.0016 - 0.0016 -
- 49 - 82
Ti-6Al-4V, etc. 0.0028 0.0028 0.0028 0.0028 0.0028
Heat-resistant alloys 0.0012 - 0.0012 - 0.0012 - 0.0012 - 0.0012 -
- 328 - 66
Inconel 718, etc. 0.0024 0.0024 0.0024 0.0024 0.0024
SKD61, SKT4, etc. 40 - 50 0.0016 - 0.0016 - 0.0016 - 0.0016 - 0.0016 -
49 - 82
H13, etc. HRC 0.0028 0.0028 0.0028 0.0028 0.0028
Hardened steel
SKD11, SKH, etc. 50 - 60 0.0012 - 0.0012 - 0.0012 - 0.0012 - 0.0012 -
328 - 66
D2, etc. HRC 0.0024 0.0024 0.0024 0.0024 0.0024

Chamfering

D186 www.tungaloyamerica.com
VG C **-02. . .

Multi Function
Tun g M e i s te r h e a d f o r co unter b o r i ng

3°
S

øDch6

ød1
r ap
L ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap r S L Wrench Torque*

VGC031L31R016-U02S05 z 2 10° 0.312 0.297 0.310 0.016 S05 0.390 KEYV-S05 5.16
VGC037L38R016-U02S06 z 2 10° 0.375 0.360 0.380 0.016 S06 0.485 KEYV-S05 7.38
VGC050L55R016-U02S08 z 2 10° 0.500 0.453 0.433 0.016 S08 0.598 KEYV-S05 11.06
VGC056L43R016-U02S08 z 2 10° 0.562 0.450 0.460 0.016 S08 0.590 KEYV-S05 11.06
VGC062L63R016-U02S10 z 2 10° 0.625 0.600 0.600 0.016 S10 0.750 KEYV-S06 20.65
VGC062L63R032-U02S10 z 2 10° 0.625 0.600 0.600 0.032 S10 0.750 KEYV-S06 20.65
• Can drill with step feed
*Torque: Recommended torque (lbf·ft) for clamping.
Packing quantity = 2 pcs.

STA NDA RD CUT TING CONDITIONS

Counter boring (VGC)
Cutting speed Feed
ISO Workpiece material Hardness
Vc (sfm) f (ipr)
Low carbon steels
- 300 HB 131 - 262 0.002 - 0.002
1045, 1055, etc.

High carbon steels

- 300 HB 98 - 164 0.002 - 0.003
4140,etc.
Prehardened steel
30 - 40 HRC 66 - 98 0.002 - 0.003
PX5, NAK80 etc
Stainless steels Square
- 200 HB 49 - 82 0.002 - 0.003
304, 316, etc.
Grey cast irons
150 - 250 HB 197 - 328 0.002 - 0.09
250, 300, etc.

Ductile cast irons

150 - 250 HB 197 - 328 0.002 - 0.003
400-15S, etc.
Titanium alloys
- 49 - 82 0.002 - 0.003
Ti-6Al-4V etc

Heat-resistant alloys
- 33 - 66 0.001 - 0.06
Inconel 718 etc
SKD61, SKT4 etc
40 - 50 HRC 49 - 82 0.002 - 0.003
H13, etc.
Hardened steel
SKD11, SKH etc
50 - 60 HRC 33 - 66 0.001 - 0.002
D2, etc.

･ When drilling, the step feed (woodpeckering feed) operation should be applied with the depth of 0.011" - 0.019" per step.
･ Apply the same cutting conditions as the VEE type head when conducting shoulder milling or slotting operations.

Tungaloy D187
 Multi Function V CA**-04, 06...
Tu n g M e i s te r h ead w i t h 4 o r 6 f l utes f o r cou n te r s i n ki n g a n d c h a m f e r i n g

L S

ød min
øDc

ød1
ap
45°
ap = Max. depth of cut, S = Connection screw size

Inch AH725 z Helx øDc ød1 Max. ap ød min S L Wrench Torque**

VCA0375L16A45-U04S06 z 4 0° 0.375 0.375 0.150 0.073 S06 0.512 KEYV-S06 7.38

Metric AH725 z Helx øDc ød1 Max. ap ød min S L Wrench Torque**

VCA100L04.0A45-04S06 z 4 0° 10 10 4 1.95 S06 13 KEYV-S06 10
VCA120L05.0A45-04S08 z 4 0° 12 12 5 1.95 S08 16.5 KEYV-S08 15
VCA127L05.3A45-04S08 z 4 0° 12.7 12.7 5.3 1.98 S08 16.5 KEYV-S08 15
VCA160L06.5A45-06S10 z 6 0° 16 16 6.5 3 S10 20.3 KEYV-S10 28
VCA200L07.5A45-06S12 z 6 0° 20 18.3 7.5 5 S12 25.5 KEYV-S12 28

**Torque: Recommended torque (lbf·ft, N∙m) for clamping. z: Line up

Packing quantity = 2 pcs.

V C W **-02. . .
Tu n g M e i s te r h ead f o r co unter si nk i ng , to p a n d b ot tom c h a m f e r i n g

L
90°
ø1,2

S
øDc

ød1
90°

ap1
k
ap2 ap 1,2 = Max. depth of cut, S = Connection screw size

Metric AH725 z Helx øDc ød1 ap1 ap2 k S L Wrench Torque**

VCW118L05.0A45-02S06 z 2 0° 11.8 9.3 5 1.2 2 S06 11.2 KEYV-S08 10

• Available for chamfering of reverse side z: Line up

* Some heads require different wrench size.
**Torque: Recommended torque (N∙m) for clamping.
Chamfering Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D189

D188 www.tungaloyamerica.com
VC R **-02. . .

Multi Function
Tun g M e i s te r h e a d w i t h 2 p ressed f l utes f o r c on c a v e ra d i u s c h a m f e r i n g

øDch10

ød1
ød
r ap
L
ap = Max. depth of cut, S = Connection screw size

Metric AH725 z Helx øDc ød1 ød Max. ap r S L Wrench Torque**

VCR080L07.5R10-02S05 z 2 0° 8 7.6 5.8 7.5 1 S05 10.5 KEYV-S05 7
VCR100L09.5R16-02S06 z 2 0° 10 9.5 6.8 9.5 1.6 S06 12.5 KEYV-S06 10
VCR100L09.5R25-02S06 z 2 0° 10 9.5 5.1 9.5 2.5 S06 12.5 KEYV-S06 10
VCR127L12.0R30-02S08 z 2 0° 12.7 12.2 6.5 12.0 3 S08 15.6 KEYV-S08 15
VCR127L12.0R40-02S08 z 2 0° 12.7 12.2 4.7 12.0 4 S08 15.6 KEYV-S08 15
VCR160L15.0R50-02S10 z 2 0° 16 15.2 6.2 15.0 5 S10 19.1 KEYV-S10 28
VCR200L07.0R60-02S12 z 2 0° 20 18.3 8 7.0 6 S12 17.4 KEYV-S12 28

**Torque: Recommended torque (N∙m) for clamping. z: Line up

Packing quantity = 2 pcs.

STA NDA RD CUT TING CONDITIONS

Chamfering and countersinking (VCA, VCW, VCR, VCP)
Cutting speed Feed
ISO Workpiece material Hardness
Vc (sfm) f (ipr)
Low carbon steels
- 300 HB 197 - 328 0.0024 - 0.0047
1045, 1055, etc.
High carbon steels
- 300 HB 164 - 262 0.0024 - 0.0047
4140,etc.
Prehardened steel
30 - 40 HRC 131 - 230 0.0024 - 0.0047
PX5, NAK80 etc
Stainless steels
SUS304, SUS316, etc. - 200 HB 98 - 164 0.0024 - 0.0047
304, 316, etc.
Grey cast irons
150 - 250 HB 262 - 394 0.0024 - 0.0047
250, 300, etc.

Ductile cast irons

150 - 250 HB 262 - 394 0.0024 - 0.0047
400-15S, etc.

Aluminum alloys - 328 - 656 0.0031 - 0.0059

Titanium alloys
Ti-6Al-4V, etc.
- 98 - 164 0.0020 - 0.0039

Heat-resistant alloys Chamfering

Inconel 718, etc.
- 66 - 131 0.0016 - 0.0031

SKD61, SKT4, etc.

X40CrMoV5 1, 55NiCrMoV6, etc.
40 - 50 HRC 98 - 164 0.0020 - 0.0039
SKD61, SKT4 etc
SKD11, SKH etc
50 - 60 HRC 66 - 131 0.0016 - 0.0031
D2, etc.

Tungaloy D189
 Multi Function V ST**-3. . .
Tu n g M e i s te r h ead f o r sl o t t i ng o f 1 .5 - 3 .17m m w i d t h w i t h 3 te e t h

øDc W 侑 1.2 mm
S

Tmax
r

Tmax
W W
S = Connection screw size

Metric GH130 z Helx øDc W ± 0.02 r S T max Wrench Torque*

VST157W1.50R010-3S06 z 3 0° 15.7 1.5 0.1 S06 2.8 KEYV-177 10
VST157W1.57R020-3S06 z 3 0° 15.7 1.57 0.2 S06 2.8 KEYV-177 10
VST157W2.00R020-3S06 z 3 0° 15.7 2 0.2 S06 2.8 KEYV-177 10
VST157W2.39R020-3S06 z 3 0° 15.7 2.39 0.2 S06 2.8 KEYV-177 10
VST157W2.50R020-3S06 z 3 0° 15.7 2.5 0.2 S06 2.8 KEYV-177 10
VST157W3.00R020-3S06 z 3 0° 15.7 3 0.2 S06 2.8 KEYV-177 10
VST157W3.17R020-3S06 z 3 0° 15.7 3.17 0.2 S06 2.8 KEYV-177 10
(1)
VST177W1.20R005-3S06 z 3 0° 17.7 1.2 0.05 S06 3.8 KEYV-177 10
(1)
VST177W1.40R005-3S06 z 3 0° 17.7 1.4 0.05 S06 3.8 KEYV-177 10
VST177W1.50R010-3S06 z 3 0° 17.7 1.5 0.1 S06 3.8 KEYV-177 10
VST177W1.57R020-3S06 z 3 0° 17.7 1.57 0.2 S06 3.8 KEYV-177 10
(1)
VST177W1.70R005-3S06 z 3 0° 17.7 1.7 0.05 S06 3.8 KEYV-177 10
VST177W2.00R020-3S06 z 3 0° 17.7 2 0.2 S06 3.8 KEYV-177 10
VST177W2.20R110-3S06 z 3 0° 17.7 2.2 1.1 S06 3.8 KEYV-177 10
VST177W2.39R020-3S06 z 3 0° 17.7 2.39 0.2 S06 3.8 KEYV-177 10
VST177W2.50R020-3S06 z 3 0° 17.7 2.5 0.2 S06 3.8 KEYV-177 10
VST177W3.00R020-3S06 z 3 0° 17.7 3 0.2 S06 3.8 KEYV-177 10
VST177W3.17R020-3S06 z 3 0° 17.7 3.17 0.2 S06 3.8 KEYV-177 10

(1) W is based on DIN471 / 472 z: Line up

*Torque: Recommended torque (N∙m) for clamping.
Packing quantity = 2 pcs.

Slotting

Reference pages
Standard cutting conditions → D193

D190 www.tungaloyamerica.com
VST**-4, 6. . .

Multi Function
Tun g M e i s te r h e a d f o r sl o t t i ng o f 0 .7 6 - 1 0 m m w i d t h w i t h 4, 6 te e t h

øDc W 侑1.0 mm øDc

S S

Tmax
W r r

Tmax

Tmax
W W
S = Connection screw size

Metric GH130 Helx z øDc W ± 0.02 r S T max Wrench Torque*

(1)
VST217W0.76R000-4S08 z 0° 4 21.7 0.76 - S08 0.059 KEYV-217 15
(1)
VST217W0.86R000-4S08 z 0° 4 21.7 0.86 - S08 0.067 KEYV-217 15
(1)
VST217W0.96R000-4S08 z 0° 4 21.7 0.96 - S08 0.075 KEYV-217 15
VST217W1.00R005-4S08 z 0° 4 21.7 1 0.002 S08 0.079 KEYV-217 15
(1)
VST217W1.20R005-4S08 z 0° 4 21.7 1.2 0.002 S08 0.177 KEYV-217 15
(1)
VST217W1.40R005-4S08 z 0° 4 21.7 1.4 0.002 S08 0.177 KEYV-217 15
VST217W1.57R000-4S08 z 0° 4 21.7 1.57 - S08 0.177 KEYV-217 15
(1)
VST217W1.70R010-4S08 z 0° 4 21.7 1.7 0.004 S08 0.177 KEYV-217 15
(1)
VST217W1.95R020-4S08 z 0° 4 21.7 1.95 0.008 S08 0.177 KEYV-217 15
VST217W2.00R020-4S08 z 0° 4 21.7 2 0.008 S08 0.177 KEYV-217 15
(1)
VST217W2.25R020-4S08 z 0° 4 21.7 2.25 0.008 S08 0.177 KEYV-217 15
VST217W2.39R020-4S08 z 0° 4 21.7 2.39 0.008 S08 0.177 KEYV-217 15
VST217W2.50R020-4S08 z 0° 4 21.7 2.5 0.008 S08 0.177 KEYV-217 15
(1)
VST217W2.75R020-4S08 z 0° 4 21.7 2.75 0.008 S08 0.177 KEYV-217 15
VST217W3.00R020-4S08 z 0° 4 21.7 3 0.008 S08 0.177 KEYV-217 15
VST217W3.17R020-4S08 z 0° 4 21.7 3.17 0.008 S08 0.177 KEYV-217 15
(1)
VST217W3.25R020-4S08 z 0° 4 21.7 3.25 0.008 S08 0.177 KEYV-217 15
VST217W4.00R020-4S08 z 0° 4 21.7 4 0.008 S08 0.177 KEYV-217 15
(1)
VST217W4.25R020-4S08 z 0° 4 21.7 4.25 0.008 S08 0.177 KEYV-217 15
VST217W4.75R020-4S08 z 0° 4 21.7 4.75 0.008 S08 0.177 KEYV-217 15
(1)
VST217W5.25R020-4S08 z 0° 4 21.7 5.25 0.008 S08 0.177 KEYV-217 15
VST277W2.50R020-6S10 z 0° 6 27.7 2.5 0.008 S10 0.236 KEYV-T40L 28
VST277W5.25R020-6S10 z 0° 6 27.7 5.25 0.008 S10 0.236 KEYV-T40L 28
VST277W10.0R020-6S10 z 0° 6 27.7 10 0.008 S10 0.236 KEYV-T40L 28

(1) W is based on DIN471 / 472 z: Line up

*Torque: Recommended torque (N∙m) for clamping.
Packing quantity = 2 pcs.

VST**A45. . .
Tun g M e i s te r h e a d f o r cham f er i ng o n sl o t s

VST177 øDc R0.1 VST217 øDc k

t

Slotting
ƴ° ƴ° ƴ° ƴ°

S S
W W
S = Connection screw size

Metric GH130 z Helx øDc W ƴ˚ S t k Wrench Torque*

VST177L01.40A45-3S06 z 3 0° 17.7 3.4 45 S06 1.4 - KEYV-177 10
VST217L01.70A45-4S08 z 4 0° 21.7 5.5 45 S08 1.7 1.5 KEYV-217 15

*Torque: Recommended torque (N∙m) for clamping. z: Line up

Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D193

Tungaloy D191
 Multi Function V TB **-06. . .
Tu n g M e i s te r h ead f o r T- sl o t t i ng o f 0 .1 2 5 " - 0. 312" w i d t h

øDc

Tmax
r W
S = Connection screw size
0
Inch GH130 z Helx øDc - 0.002" W± 0.0008" T max S r Wrench Torque*
VTB05W125R016-U06S05 z 6 0° 0.500 0.125 0.088 S05 0.016 KEYV-T20 5.16
VTB06W056R016-U06S06 z 6 0° 0.625 0.056 0.125 S06 0.016 KEYV-T20 7.38
VTB06W063R016-U06S06 z 6 0° 0.625 0.063 0.125 S06 0.016 KEYV-T20 7.38
VTB06W068R016-U06S06 z 6 0° 0.625 0.068 0.125 S06 0.016 KEYV-T20 7.38
VTB06W078R016-U06S06 z 6 0° 0.625 0.078 0.125 S06 0.016 KEYV-T20 7.38
VTB06W086R016-U06S06 z 6 0° 0.625 0.086 0.125 S06 0.016 KEYV-T25 7.38
VTB06W105R016-U06S06 z 6 0° 0.625 0.105 0.125 S06 0.016 KEYV-T25 7.38
VTB06W125R016-U06S06 z 6 0° 0.625 0.125 0.125 S06 0.016 KEYV-T25 7.38
VTB06W156R016-U06S06 z 6 0° 0.625 0.156 0.125 S06 0.016 KEYV-T25 7.38
VTB07W156R016-U06S08 z 6 0° 0.750 0.156 0.120 S08 0.016 KEYV-T30L 11.06
VTB07W187R016-U06S08 z 6 0° 0.750 0.187 0.120 S08 0.016 KEYV-T30L 11.06
VTB07W250R016-U06S08 z 6 0° 0.750 0.250 0.120 S08 0.016 KEYV-T30L 11.06
VTB08W187R016-U06S08 z 6 0° 0.875 0.187 0.190 S08 0.016 KEYV-T40L 11.06
VTB08W250R016-U06S08 z 6 0° 0.875 0.250 0.190 S08 0.016 KEYV-T40L 11.06
VTB08W312R016-U06S08 z 6 0° 0.875 0.312 0.190 S08 0.016 KEYV-T40L 11.06
VTB10W187R016-U06S10 z 6 0° 1.000 0.187 0.177 S10 0.016 KEYV-T50L 20.65
VTB10W250R016-U06S10 z 6 0° 1.000 0.250 0.177 S10 0.016 KEYV-T50L 20.65
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

V TB **C 006. . .
Tu n g M e i s te r h ead f o r T- sl o t t i ng o f 0 .0 6 2 " - 0. 078" w i d t h w i t h c h a m f e re d e d ge s

S
øDc

T max

C W
S = Connection screw size
0
Inch GH130 z Helx øDc - 0.002" W± 0.002" T max S C Wrench Torque*
Slotting VTB05W062C006-U06S05 z 6 0° 0.500 0.062 0.089 S05 0.006 KEYV-T20 5.16
VTB05W078C006-U06S05 z 6 0° 0.500 0.078 0.089 S05 0.006 KEYV-T20 5.16
*Torque: Recommended torque (lbf·ft) for clamping. z: Line up
Packing quantity = 2 pcs.

Reference pages
Standard cutting conditions → D193

D192 www.tungaloyamerica.com
 STA NDA RD CUT TING CONDITIONS
Slotting (VST, VTB)

Multi Function
VST type VTB type
Hardness
ISO Workpiece material Cutting speed Feed per tooth Cutting speed Feed per tooth
HB
Vc (sfm) fz (ipt) Vc (sfm) fz (ipt)
Low carbon steels
- 300 262 - 591 0.002 - 0.006 262 - 591 0.003 - 0.007
1045, 1055, etc.

High carbon steels

- 300 197 - 394 0.002 - 0.005 197 - 394 0.002 - 0.006
4140,etc.

Stainless steels
- 200 164 - 394 0.002 - 0.005 164 - 394 0.002 - 0.006
304, 316, etc.

Grey cast irons

150 - 250 328 - 656 0.002 - 0.006 328 - 656 0.003 - 0.007
250, 300, etc.

Ductile cast irons

150 - 250 328 - 656 0.002 - 0.005 328 - 656 0.002 - 0.006
400-15S, etc.

Aluminum alloys
Si < 13%
- 656 - 1969 0.002 - 0.006 656 - 1969 0.003 - 0.007

Aluminum alloys
Si ≥13%
- 328 - 984 0.001 - 0.005 328 - 984 0.002 - 0.006

Titanium alloys
Ti-6Al-4V, etc.
- 131 - 197 0.002 - 0.002 131 - 197 0.002 - 0.006

Heat-resistant alloys
Inconel 718, etc.
- 49 - 115 0.001 - 0.004 49 - 115 0.001 - 0.004

Slotting

Tungaloy D193
 Multi Function VSS...
Tu n g M e i s te r, st rai g ht neck and cy l i nd r i cal s h a n k

øDs
ød1
S L3
L2
L1
S = Connection screw size

Inch øDs ød1 L1 L2 L3 S Type Material

VSS031L250S05US 0.312 0.300 2.500 0.590 0.510 S05 CYLINDRICAL STEEL
VSS037L300S06US 0.375 0.364 3.000 0.590 0.510 S06 CYLINDRICAL STEEL
VSS050L350S08US 0.500 0.480 3.540 0.630 0.530 S08 CYLINDRICAL STEEL
VSS062L400S10US 0.625 0.598 4.000 0.780 0.680 S10 CYLINDRICAL STEEL
VSS075L500S12US 0.750 0.720 5.000 1.000 0.880 S12 CYLINDRICAL STEEL
VSS031L300S05UC 0.312 0.300 3.000 1.000 0.950 S05 CYLINDRICAL CARBIDE
VSS031L350S05UC 0.312 0.300 3.500 1.500 1.450 S05 CYLINDRICAL CARBIDE
VSS031L400S05UC 0.312 0.300 4.000 2.000 1.950 S05 CYLINDRICAL CARBIDE
VSS037L400S06UC 0.375 0.364 4.000 1.250 1.200 S06 CYLINDRICAL CARBIDE
VSS037L475S06UC 0.375 0.364 4.750 2.000 1.950 S06 CYLINDRICAL CARBIDE
VSS050L400S08UC 0.500 0.480 4.000 1.500 1.400 S08 CYLINDRICAL CARBIDE
VSS050L550S08UC 0.500 0.480 5.500 2.500 2.450 S08 CYLINDRICAL CARBIDE
VSS062L325S10UC 0.625 0.600 3.250 1.250 1.180 S10 CYLINDRICAL CARBIDE
VSS062L450S10UC 0.625 0.600 4.500 2.500 2.430 S10 CYLINDRICAL CARBIDE
VSS062L550S10UC 0.625 0.600 5.500 3.500 3.430 S10 CYLINDRICAL CARBIDE
VSS062L700S10UC 0.625 0.600 7.000 5.000 4.930 S10 CYLINDRICAL CARBIDE
VSS075L400S12UC 0.750 0.720 4.000 1.500 1.430 S12 CYLINDRICAL CARBIDE
VSS075L550S12UC 0.750 0.720 5.500 3.000 2.930 S12 CYLINDRICAL CARBIDE
VSS075L800S12UC 0.750 0.720 8.000 4.500 4.430 S12 CYLINDRICAL CARBIDE
VSS031L300S05UW 0.312 0.299 3.000 1.000 0.978 S05 CYLINDRICAL TUNGSTEN
VSS031L450S05UW 0.312 0.299 4.500 2.000 1.978 S05 CYLINDRICAL TUNGSTEN
VSS037L355S06UW 0.375 0.364 3.550 0.750 0.680 S06 CYLINDRICAL TUNGSTEN
VSS050L425S08UW 0.500 0.480 4.250 0.630 0.530 S08 CYLINDRICAL TUNGSTEN
VSS050L218W05US 0.500 0.299 2.185 0.150 - S05 WELDON STEEL
Square VSS062L258W06US 0.625 0.366 2.580 0.236 - S06 WELDON STEEL
VSS062L258W08US 0.625 0.480 2.580 0.157 - S08 WELDON STEEL
R VSS075L275W10US 0.750 0.598 2.750 0.157 - S10 WELDON STEEL
Radius VSS100L300W12US 1.000 0.720 3.000 0.283 - S12 WELDON STEEL
VSS100L537S15US 1.000 0.957 5.375 1.375 1.313 S15 CYLINDRICAL STEEL
VSS100L475S15UC 1.000 0.957 4.750 2.375 2.313 S15 CYLINDRICAL CARBIDE
VSS100L675S15UC 1.000 0.957 6.750 4.000 3.938 S15 CYLINDRICAL CARBIDE
Ball
VSS100L1000S15UC 1.000 0.957 10.000 6.000 5.938 S15 CYLINDRICAL CARBIDE

Chamfering
V S S D **W. . .
Tu n g M e i s te r, st rai g ht neck and w el d o n sh a n k
øDs
ød1

S L3
L2
L1
S = Connection screw size

Metric øDs ød1 L1 L2 L3 S Shank Material

VSSD12L055W05-S 12 7.6 55 3.8 - S05 WELDON STEEL
VSSD16L065W06-S 16 9.6 65 6 - S06 WELDON STEEL
VSSD16L065W08-S 16 11.5 65 4 - S08 WELDON STEEL
VSSD20L070W10-S 20 15.2 70 4 - S10 WELDON STEEL
VSSD25L075W12-S 25 18.3 75 6 - S12 WELDON STEEL

D194 www.tungaloyamerica.com
V SSD **-W -A

Multi Function
Tun g M e i s te r, s t rai g ht shank and neck w i t h c ool a n t h ol e

ød1

øDs
L3
S L2 L1
S = Connection screw size

Metric øDs ød1 L1 L2 L3 S Material

VSSD10L070S06-W-A 10 9.6 70 20 19 S06 TUNGSTEN
VSSD10L090S06-W-A 10 9.6 90 40 39 S06 TUNGSTEN
VSSD10L110S06-W-A 10 9.6 110 60 59 S06 TUNGSTEN
VSSD12L070S08-W-A 12 11.5 70 20 19 S08 TUNGSTEN
VSSD12L090S08-W-A 12 11.5 90 40 39 S08 TUNGSTEN
VSSD12L110S08-W-A 12 11.5 110 60 59 S08 TUNGSTEN
VSSD12L130S08-W-A 12 11.5 130 80 79 S08 TUNGSTEN
VSSD16L070S10-W-A 16 15.2 70 20 18.5 S10 TUNGSTEN
VSSD16L090S10-W-A 16 15.2 90 40 36.5 S10 TUNGSTEN
VSSD16L110S10-W-A 16 15.2 110 60 58.5 S10 TUNGSTEN
VSSD16L130S10-W-A 16 15.2 130 80 78.5 S10 TUNGSTEN
VSSD20L090S12-W-A 20 18.3 90 40 37 S12 TUNGSTEN
VSSD20L130S12-W-A 20 18.3 130 80 77 S12 TUNGSTEN

Square

R
Radius

Ball

Chamfering

Tungaloy D195
 Multi Function V TS . . .
Tu n g M e i s te r, st rai g ht shank and t ap er nec k

ød1

øDs
S ƴ° L3
L2
L1
S = Connection screw size

Inch α° øDs ød1 L1 L2 L3 S Material

VTS050L300S05US 85 0.500 0.300 3.000 1.000 0.930 S05 STEEL
VTS050L400S05US 89 0.500 0.300 4.000 1.500 1.300 S05 STEEL
VTS062L500S06US 89 0.625 0.370 5.000 1.380 1.283 S06 STEEL
VTS062L630S06US 89 0.625 0.364 6.300 2.170 1.750 S06 STEEL
VTS062L550S08US 85 0.625 0.480 5.500 0.870 0.770 S08 STEEL
VTS075L650S08US 89 0.750 0.480 6.500 3.150 2.770 S08 STEEL
VTS075L550S10US 85 0.750 0.598 5.500 0.880 0.000 S10 STEEL
VTS100L670S10US 89 1.000 0.598 6.700 1.600 0.000 S10 STEEL
VTS075L750S10US 89 0.750 0.600 7.500 3.150 2.950 S10 STEEL
VTS100L630S12US 89 1.000 0.720 6.300 1.600 - S12 STEEL
VTS125L750S12US 89 1.250 0.720 7.500 3.150 - S12 STEEL
VTS100L800S12US 89 1.000 0.720 8.000 3.750 3.400 S12 STEEL
VTS037L350S05UC 85 0.375 0.300 3.500 1.500 0.000 S05 CARBIDE
VTS050L450S05UC 89 0.500 0.300 4.500 2.500 1.400 S05 CARBIDE
VTS062L600S05UC 89 0.625 0.300 6.000 4.000 3.900 S05 CARBIDE
VTS050L550S06UC 89 0.500 0.364 5.500 2.500 2.470 S06 CARBIDE
VTS062L650S06UC 89 0.625 0.364 6.500 3.500 3.380 S06 CARBIDE
VTS062L650S08UC 89 0.625 0.480 6.500 3.500 3.440 S08 CARBIDE
VTS075L700S08UC 89 0.750 0.480 7.000 4.000 3.900 S08 CARBIDE
VTS075L650S10UC 85 0.750 0.600 6.500 4.000 0.000 S10 CARBIDE
VTS075L880S10UC 85 0.750 0.600 8.800 6.300 6.240 S10 CARBIDE

Square VTS100L1000S12UC 89 1.000 0.720 10.000 5.500 - S12 CARBIDE

VTS075L550S06UW 89 0.750 0.370 5.500 2.240 0.000 S06 TUNGSTEN

R VTS062L670S06UW 89 0.625 0.364 6.700 2.180 1.770 S06 TUNGSTEN

VTS075L670S08UW 85 0.750 0.480 6.700 3.150 2.700 S08 TUNGSTEN
Radius

Ball
V TS D **-W -A
Tu n g M e i s te r, st rai g ht shank and t ap er nec k w i t h c ool a n t h ol e
Chamfering
øDs
ød1

S ƴ° L3
L2
L1
S = Connection screw size

Metric α° øDs ød1 L1 L2 L3 S Material

VTSD12L110S06-W-A 89 12 9.6 110 60 59 S06 TUNGSTEN
VTSD16L170S06-W-A 89 16 9.6 170 120 116 S06 TUNGSTEN

D196 www.tungaloyamerica.com
VS C . . .

Multi Function
Tun g M e i s te r, s t rai g ht shank f o r V ST t y p e sl ot t i n g h e a d s

VSC type VSC-A type

S S

øDs
ød1

øDs

ød1
L L

S = Connection screw size

Inch øDs ød1 L S Air hole Material

VSC095L080S06-C 0.375 0.375 3.150 S06 without CARBIDE
VSC127L120S08-C-A 0.500 0.500 4.724 S08 with CARBIDE

Metric øDs ød1 L S Air hole Material

VSC100L100S06-C 10 10 100 S06 without CARBIDE
VSC120L100S08-C-A 12 12 100 S08 with CARBIDE
Note: • For VSC-C type shank, just VST slotting head is recommended.
If other heads are used on the VSC-C shank, the depth of cut must be smaller than the max. ap in each head.
The VSC-C type shank does not have external clearance, so the shank may interfere with the work piece.

V STD. . .
Tun g M e i s te r, s t rai g ht shank f o r V T B t y p e sl ot t i n g h e a d s

øDs
ød1

S = Connection screw size

Inch øDs ød1 L S Material

VST031L275S05US  0.312 0.312 2.750 S05 CARBIDE
VST037L325S06US  0.375 0.375 3.250 S06 CARBIDE
VST050L375S08US  0.500 0.500 3.750 S08 CARBIDE
VST062L400S10US  0.625 0.625 4.000 S10 CARBIDE

Metric øDs ød1 L S Material

VSTD08L070S05-S 8 8 70 S05 STEEL
VSTD10L080S06-S 10 10 80 S06 STEEL
VSTD12L090S08-S 12 12 90 S08 STEEL
VSTD16L100S10-S 16 16 100 S10 STEEL

Note: •For VSTD type shank, just VTB grooving head is recommended.
If other heads are used on the VSTD shank, the depth of cut must be smaller than the max. ap in each head. Slotting
The VSTD type shank does not have external clearance, so the shank may interfere with the work piece.

Tungaloy D197
 Multi Function VA D **-M . . .
Tu n g F l ex c o n v er si o n ad ap to r w i t h Tung M e i s te r

øD3
øD2

M
L3
L L2 T
S = Connection screw size

Metric øD2 øD3 L L2 L3 S M T

VAD130L016S08-S-M8 11.7 13 16 17.5 6 S08 M8 11
VAD130L025S08-S-M8 11.7 13 25 17.5 20 S08 M8 11
VAD180L020S08-S-M10 11.7 18 20 20 12 S08 M10 13
VAD180L025S08-S-M10 11.7 18 25 20 15 S08 M10 11
VAD210L020S08-S-M12 11.7 21 20 20 10 S08 M12 12.75
VAD210L025S08-S-M12 11.7 21 25 20 13 S08 M12 12.75

WR ENCH
Appearance Connection
Designation Torque (N·m) Applicable head
screw size
KEYV-S05 S05 7
Square
KEYV-S06 S06 10 Ball
KEYV-S08 S08 15 Radius
KEYV-S10 S10 28 Drilling
KEYV-S12 S12 28 Chamfering
Counter boring
KEYV-W20 S15 40
KEYV-177 S06 10
Slotting VST type
KEYV-217 S08 15
S08 15
KEYV-T40L Slotting VST, VTB type
S10 28
S05 7
KEYV-T20
S06 10
KEYV-T25 S06 10
Slotting VTB type
KEYV-T30L S08 15
S08 15
KEYV-T50L
S10 28
Note: Optional parts

CAUTIONARY POINTS IN USE

· The cutting heads specified by Tungaloy must be used. Avoid using alternate
heads that are not Tungaloy products as this will damage the shank and can
Slotting
cause severe accident or injury.
· Before setting the head, clean the connection screw with an air blast or a wiping
OK
cloth to remove chips and other foreign matter that may remain.
· Do not apply the lubricant to the connection screw.
· Please use the correct “Wrench” with the correct cutting head. Tighten the head Gap
slowly until the face of the head contacts the shank. (Please refer to the picture
shown on the right.) Do not re-tightening or over-tightening. Excessive tightening
may cause the cutting head to break.
· Do not apply excessive force or a hammer when tightening or exchanging the
cutting heads.

D198 www.tungaloyamerica.com
 Multi Function
MEMO

Tungaloy D199
Multi Function EV H
M u l t i p u r p o s e end m i l l s w i t h center ed g e i n s m a l l d i a m e te r

A.R. = +20, R.R. = +12

øDsh6
øDc
ap 1˚
Ra
Lf Rs
L
Right hand (R) shown.

Inch Max. ap øDc z øDs ℓs Lf ℓa L Insert

EVH06R039U0050-02 0.118 0.394 2 0.500 0.196 1.575 0.197 3.570 XVGT06H20...
EVH07R050U0050-02 0.138 0.500 2 0.500 0.236 1.890 0.236 4.000 XVGT07X30...
EVH09R063U0063-02 0.177 0.625 2 0.625 0.315 2.520 0.315 4.500 XVGT09X40...

SPARE PARTS
① Clamping
Designation Lubricant Wrench Wrench 1
screw
EVH06R039U0050-02 CSPD-1.8S M-1000 - IP-6F
EVH07R050U0050-02 CSPB-2H M-1000 - IP-6F
EVH09R063U0063-02 CSPB-2.5S M-1000 IP-8D -

Insert

Reference pages
Inserts → D201, Standard cutting conditions → D202

D200 www.tungaloyamerica.com
 INSERT
X VGT EC -M J (Cent ral ) X V GT E P-M J ( Pe r ip h e ra l)

Multi Function
T A T A

B
B
rε rε
X VGT FC -AJ (Cent ral ) X V GT F P-AJ ( Pe r ip h e ra l)
T A T A

B
B

rε rε
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys : First choice
H Hard materials : Second choice
Coated
DS1200

rε Max.
AH730

Designation ap A B T

XVGT06H205EC-MJ 0.020 0.118 z 0.244 0.197 0.098

XVGT08X305EC-MJ 0.020 0.138 z 0.280 0.240 0.118
XVGT09X405EC-MJ 0.020 0.177 z 0.354 0.323 0.157
XVGT06H205EP-MJ 0.020 0.118 z 0.244 0.209 0.098
XVGT07X305EP-MJ 0.020 0.138 z 0.280 0.252 0.118
XVGT09X405EP-MJ 0.020 0.177 z 0.354 0.323 0.157
XVGT06H205FC-AJ 0.020 0.118 z 0.244 0.197 0.098
XVGT08X305FC-AJ 0.020 0.138 z 0.280 0.240 0.118
XVGT09X405FC-AJ 0.020 0.177 z 0.354 0.323 0.157
XVGT06H205FP-AJ 0.020 0.118 z 0.244 0.209 0.098
XVGT07X305FC-AJ 0.020 0.138 z 0.280 0.252 0.118
XVGT07X305FP-AJ 0.020 0.138 z 0.280 0.252 0.118
XVGT09X405FP-AJ 0.020 0.177 z 0.354 0.323 0.157

z: Line up

Tungaloy D201
 STA NDA RD CUT TING CONDITIONS
Shoulder milling, Slotting Workpiece Carbon steels Alloy steels and Aluminum alloys Aluminum alloys
Multi Function
and Stainless steels Cast irons
material alloy steels prehardened steels (Si < 13%) (Si ≥ 13%)
Hardness < 30HRC 30 - 40HRC < 250HB - - -
Cutting speed Vc = 160 - 400 SFM Vc = 100 - 330 SFM Vc = 160 - 400 SFM Vc = 200 - 140 SFM Vc = 330 - 980 SFM Vc = 330 - 650 SFM
No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf
Conditions
min-1 in/min min-1 in/min min-1 in/min min-1 in/min min-1 in/min min-1 in/min
ø0.394 2550 15 1910 8 2550 15 3180 20 6370 40 4770 26
ap
ap

Tool dia.
ø0.500 2120 13 1590 6 2120 13 2650 17 5300 33 3980 22
ae (in)
ø0.625 1590 9 1190 5 1590 9 1990 13 3980 25 2980 17
Side cutting Slotting Side ap < 0.25D ap < 0.25D ap < 0.25D ap < 0.25D ap < 0.25D ap < 0.25D
ap: Axial depth of cut
Depth of cutting ae < 0.2D ae < 0.2D ae < 0.2D ae < 0.3D ae < 0.3D ae < 0.3D
cut
ae: Radial depth of cut Slotting ap < 0.1D ap < 0.1D ap < 0.1D ap < 0.006D ap < 0.2D ap < 0.2D
Drilling•Plunging Workpiece Carbon steels
and
Alloy steels and
Stainless steels Cast irons
Aluminum alloys Aluminum alloys
material alloy steels prehardened steels (Si < 13%) (Si ≥ 13%)
Hardness < 30HRC 30 - 40HRC < 250HB - - -
Cutting speed Vc = 160 - 400 SFM Vc = 100 - 330 SFM Vc = 160 - 400 SFM Vc = 200 - 460 SFM Vc = 330 - 980 SFM Vc = 330 - 980 SFM
No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf No. of rev. n Feed
speed vf
Conditions
min-1 in/min min-1 in/min min-1 in/min min-1 in/min min-1 in/min min-1 in/min
ø0.394 2550 5 1910 3 2550 5 3180 7 6370 18 4770 11
Tool dia.
ø0.500 2120 4 1590 3 2120 4 2650 6 5300 15 3980 9
(in)
ø0.625 1590 3 1190 2 1590 3 1990 5 3980 11 2980 7
Note:
• In slotting or pocketing where chips tend to stay in the cutting zone, use • Tool overhang length must be as short as possible to avoid chatter. When
air blast to remove chips to prevent chip recutting. the tool overhang length is long, decrease the number of revolutions and
• When chips tend to weld excessively on the cutting edge such as in ma- feed.
chining aluminum alloys, use a water soluble cutting fluid. • Cutting conditions are generally limited by the rigidity and power of the
• In the case of cutting a casting skin or a heavily interrupted work surface, machine and the rigidity of the workpiece. When setting the conditions,
decrease the feed per tooth and the maximum depth of cut to 1/2 to 2/3 start from half of the values of the standard cutting conditions and then
times the values shown in the table. increase the value gradually while making sure that the machine is running
normally.

A PPLICATION R A NGE
Shoulder
milling Enlarging hole
Slotting
Drilling Plunging

Drilling
(Helical feed)

Ramping
H1

ae
°
H

W
ap

ap

øD1, øD2

Max.cutting Min. Min. Max. cutting

Max. depth Max.drilling width in Max. ramping machinable machinable width in Max.depth
of cut depth plunging angle hole dia. hole dia. enlarging hole of boring
Inch øDc ap H W θ° øD1 øD2 ae H1
EVH06R039U0050-02 ø0.394 0.118 0.196 0.196 5 0.472 0.749 0.354 1.120

EVH07R050U0050-02 ø0.500 0.138 0.236 0.236 5 0.551 0.906 0.433 1.420

EVH09R063U0063-02 ø0.625 0.177 0.315 0.315 5 0.708 1.220 0.590 1.890

D202 www.tungaloyamerica.com
EV X
M u l t i p u r p o s e e nd m i l l s w i t h center ed g e i n m e d i u m d i a m e te r
Standard type A.R. = +2˚~ +5˚, R.R. = -10˚~ -3.5˚

Multi Function
Long type A.R. = +5˚, R.R. = -4˚~ -2˚

øDc
øDc

øDc
øDsh6
Rs Lf Rs

øDsh6
Lf

øDsh6
90˚ Lf Rs 90˚
L 90˚ L
L
Fig.A Fig.B Fig.C

Inch Max. ap øDc z øDs ℓs Lf L Air hole Fig. Insert

EVX08062RSU 0.276 0.625 2 0.625 1.906 1.250 3.156 with C XXMU08...
EVX10020RSU 0.276 0.787 2 0.750 2.031 1.250 3.281 with C XXMU10...
EVX12100RSU 0.276 1.000 2 1.000 2.281 1.625 3.906 with C XXMU12...
EVX16125RSU 0.276 1.250 2 1.250 2.281 2.000 4.281 without C XXMU16...
EVX08062RLHU 0.276 0.625 2 0.625 5.375 1.625 7.000 with A XXMU08...
EVX10020RLHU 0.276 0.787 2 0.750 5.500 2.000 7.500 without A XXMU10...
EVX12100RLHU 0.354 1.000 2 1.000 6.000 2.750 8.750 with A XXMU12...
EVX16125RLHU 0.354 1.250 2 1.250 6.750 3.250 10.000 with A XXMU16...

Metric Max. ap øDc z øDs ℓs Lf L Air hole Fig. Insert

EVX08016RSA-E 7 16 2 16 55 30 85 with C XXMU08...
EVX08016RLA-E 7 16 2 16 55 50 105 with C XXMU08...
EVX08016RSA 7 16 2 16 90 30 120 with A XXMU08...
EVX08016RS 7 16 2 16 90 30 120 without A XXMU08...
EVX08016RLA 7 16 2 16 135 40 175 with A XXMU08...
EVX08016RL 7 16 2 16 135 40 175 without A XXMU08...
EVX10020RSA-E 9 20 2 20 60 30 90 with C XXMU10...
EVX10020RSA 9 20 2 20 90 30 120 with A XXMU10...
EVX10020RS 9 20 2 20 90 30 120 without A XXMU10...
EVX10020RLA-E 9 20 2 20 60 60 120 with C XXMU10...
EVX10020RLA 9 20 2 20 135 50 185 with A XXMU10...
EVX10020RL 9 20 2 20 135 50 185 without A XXMU10...
EVX12025RSA-E 11.5 25 2 25 60 40 100 with C XXMU12...
EVX12025RLA-E 11.5 25 2 25 60 75 135 with C XXMU12...
EVX12025RSA 11.5 25 2 25 100 40 140 with A XXMU12...
EVX12025RS 11.5 25 2 25 100 40 140 without A XXMU12...
EVX12025RLA 11.5 25 2 25 150 70 220 with A XXMU12...
EVX12025RL 11.5 25 2 25 150 70 220 without A XXMU16
EVX16032RSA-E 15 32 2 25 60 50 110 with C XXMU16...
EVX16032RLA-E 15 32 2 25 60 95 155 with C XXMU16...
EVX16032RSA 15 32 2 32 110 50 160 with A XXMU16...
EVX16032RS 15 32 2 32 110 50 160 without A XXMU16...
EVX16032RLA 15 32 2 32 175 80 255 with A XXMU16...
EVX16032RL 15 32 2 32 175 80 255 without A XXMU16...
EVX12040RSA 11.5 40 2 42 120 60 180 with B XXMU12, WCMT05...
EVX12040RS 11.5 40 2 42 120 60 180 without B XXMU12, WCMT05...
EVX12040RLA 11.5 40 2 42 210 100 310 with B XXMU12, WCMT05...
EVX12040RL 11.5 40 2 42 210 100 310 without B XXMU12, WCMT05...
EVX16050RSA 15 50 2 42 160 50 210 with B XXMU16, WCMT06...
EVX16050RS 15 50 2 42 160 50 210 without B XXMU16, WCMT06...
EVX16050RLA 15 50 2 42 310 50 360 with B XXMU16, WCMT06...
EVX16050RL 15 50 2 42 310 50 360 without B XXMU16, WCMT06...
EVX16063RSA 15 63 2 42 190 50 240 with B XXMU16, WCMT06...
EVX16063RS 15 63 2 42 190 50 240 without B XXMU16, WCMT06...
EVX16063RLA 15 63 2 42 310 50 360 with B XXMU16, WCMT06...
EVX16063RL 15 63 2 42 310 50 360 without B XXMU16, WCMT06...

SPARE PARTS
Designation Clamping screw Clamping screw 1 Lubricant Wrench
EVX08... - CSPB-2.2 M-1000 IP-7D
EVX10... - CSPB-2.5 M-1000 IP-8D
EVX12... - CSPD-3 M-1000 IP-10D
EVX16... CSPB-3.5 - M-1000 IP-15D

Reference pages
Inserts, Standard cutting conditions → D204

Tungaloy D203
 INSERT
Multi Function XXM U -M J W C M T-D 4
T T
A

A
θ°
rε B θ°
ød rε
P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys : First choice
H Hard materials : Second choice
Coated

AH120
AH140
Designation rε A ød T θ° B

XXMU08T204PR-MJ 0.016 z z 0.323 - 0.109 10 0.220

XXMU10H308PR-MJ 0.031 z z 0.417 - 0.138 11 0.268
XXMU12X408PR-MJ 0.031 z z 0.520 - 0.165 11 0.311
XXMU16X508PR-MJ 0.031 z z 0.661 - 0.197 11 0.437
WCMT050308-D4 - z z 0.313 0.313 0.125 7 -
WCMT06T308-D4 - z z 0.375 0.375 0.156 7 -

z: Line up

STA NDA RD CUT TING CONDITIONS

øD: ø0.625" - ø0.787" øD: ø1.000" - ø1.250"
Feed per tooth fz (ipt) Feed per tooth fz (ipt)
Cutting speed Cutting speed
ISO Workpiece material Grade Shouldering, Shouldering,
Vc (sfm) Drilling Vc (sfm) Drilling
Grooving Grooving
Carbon steels
(1018,1055, etc.) AH120 330 - 590 0.002 - 0.008 0.001 - 0.003 400 - 650 0.003 - 0.010 0.002 - 0.004
< 300 HB
Alloy steels
(4140, 4340, etc.) AH120 260 - 525 0.002 - 0.006 0.001 - 0.003 330 - 590 0.003 - 0.008 0.002 - 0.004
< 300 HB
Die steels
(H-13, etc.) AH120 200 - 400 0.002 - 0.005 0.001 - 0.002 260 - 500 0.003 - 0.006 0.001 - 0.003
< 300 HB

Stainless steels
AH140 230 - 460 0.002 - 0.006 0.001 - 0.003 300 - 525 0.003 - 0.008 0.001 - 0.003
(304SS, etc.)

Cast irons
AH120 330 - 590 0.002 - 0.010 0.001 - 0.004 400 - 650 0.003 - 0.010 0.002 - 0.004
(Class 25, etc.)

D204 www.tungaloyamerica.com
 A PPLICATION R A NGE

Multi Function
Helical feed drilling
Shoulder Milling Slotting Plunging
Enlarging hole
Drilling Ramping
θº

ap
ap

A
C

øD ae

Max. Max. cutting Max. Min. Max. Max.

Max. depth
drilling width in ramping machining machining cutting width in
of cut
depth plunging angle hole dia. hole dia. enlarging hole
Inch øDc ap A C θ° øDmin øDmax ae
EVX08062RSU/RLHU 0.625 0.276 0.315 0.315 3° 0.756 1.250 0.551

Standard type / EVX10020RSU/RLHU 0.750 0.354 0.394 0.394 3° 0.945 1.500 0.709
Long type EVX12100RSU/RLHU 1.000 0.453 0.492 0.492 3° 1.250 1.890 0.906

EVX16125RSU/RLHU 1.250 0.591 0.630 0.630 3° 1.510 2.440 1.250

Tungaloy D205
 E C C 31
Multi Function I n d ex a b l e c h am fe r i n g c u t te r w i t h l a rg e p a ra l l e l o g ra m i n s e r t

A
øD1
øDc

øDs
ø5
B κ˚ Rs
L

Inch øDc z κ° øD1 A B øDs ℓs L Insert

ECC31005RU-45 1.846 2 45 2.205 0.197 0.827 1.000 2.281 4.250 XCET3104...
ECC31005RU-30 1.338 1 30 1.575 0.197 1.004 1.000 2.281 4.250 XCET3104...
ECC31005RU-60 2.204 2 60 2.834 0.197 0.571 1.000 2.281 4.250 XCET3104...
ECC31005RU-41 1.698 2 41 2.205 0.197 0.866 1.000 2.281 4.250 XCET3104...

Metric øDc z κ° øD1 A B øDs ℓs L Insert

ECC31005R-30 34 1 30 40 14.5 25.5 32 80 130.2 XCET3104...
ECC31005R-45 46 2 45 56 20.5 20.5 32 80 130.1 XCET3104...
ECC31005R-60 55 2 60 72 25.5 14.5 32 80 130.1 XCET3104...

SPARE PARTS
Designation Clamping screw Lubricant Wrench
ECC31... CSTB-5S M-1000 T-20D

INSERT
XC ET31
T
A

45°
B

7°

2-rε P Steel  

M Stainless 
K Cast iron 
N Non-ferrous 
S Superalloys : First choice
H Hard meterials : Second choice
Un-
Coated Cermet coated
AH330
AH120
NS740

Designation rε A B T
UX30
TH10

XCET310404ER 0.016 z z z z z 0.866 0.500 0.177

z: Line up
STA NDA RD CUT TING CONDITIONS
ISO Workpiece material Grade Cutting speed: Vc (sfm) Feed per tooth: fz (sfm)
Carbon steels 1055, etc. NS740 300 - 750 0.004 - 0.010
Alloy steels 4140, etc.
< 300 HB UX30 250 - 500 0.004 - 0.010
Die steels
H13, etc. AH120 250 - 450 0.004 - 0.008
< 300 HB
Stainless steels
S30400, etc. AH330 300 - 650 0.004 - 0.010
< 250 HB
Cast irons
AH120 500 - 900 0.004 - 0.010
No.250B, etc.

Aluminum TH10 1500 - 3500 0.004 - 0.010

Notes:
• When the hole diameter to be chamfered is small or the cutting edges near • When chamfering a small diameter hole (smaller than ø0.400") in a plunge-
the front end of tool are used, use at higher side of the revolution range milling mode, peck-feeding should not be used.
shown in the Table. • When the hole diameter to be chamfered is smaller than ø0.400" or the
In contrast, when the hole diameter to be chamfered is large or the cutting cutting edges near the tool's front end are used, the feed should be set
edges far from the tool's front end are used, use the lower side of the revo- within 0.006".
lution range shown in the Table.

D206 www.tungaloyamerica.com
Guidelines for programming
Z-axis plunging depth Zd (in) in 45° chamfering of hole
Size of chamfering C (in)

Multi Function
Hole dia.ød (in)
0.020 0.039 0.059 0.079 0.118 0.157 0.197
0.197 0.028 0.047 0.067 0.087 0.126 - -
0.236 0.047 0.067 0.087 0.106 0.146 - -
0.268 0.063 0.083 0.102 0.122 0.161 - -
0.315 0.087 0.106 0.126 0.146 0.185 - -
45°
0.335 0.094 0.114 0.134 0.154 0.193 - -
0.394 0.126 0.146 0.165 0.185 0.224 0.264 0.303

Zd
0.402 0.130 0.150 0.169 0.189 0.228 0.268 0.307

C
0.472 0.165 0.185 0.205 0.224 0.264 0.303 0.343
0.551 0.205 0.224 0.244 0.264 0.303 0.343 0.382
0.630 0.244 0.264 0.283 0.303 0.343 0.382 0.421 ød
0.689 0.272 0.291 0.311 0.331 0.370 0.408 0.449
0.787 0.323 0.343 0.362 0.382 0.421 0.461 0.500
0.827 0.343 0.362 0.382 0.402 0.441 0.480 0.520
Tool: ECC31005R-45
0.945 0.402 0.421 0.441 0.461 0.500 0.539 0.579 Note: When the hole depth is smaller than the Z-axis
1.181 0.520 0.539 0.559 0.579 0.618 0.657 0.697 plunging depth (Zd), special care should be
taken to avoid an interference between the
1.299 0.579 0.598 0.618 0.638 0.677 0.717 0.756
tool's front end and the bottom of the hole.
1.417 0.638 0.657 0.677 0.697 0.736 0.776 -
1.654 0.756 0.776 0.795 - - - -

Z-axis plunging depth Zd (in) in 30° chamfering of hole

Hole dia.ød (in) Size of chamfering C (in)
0.020 0.039 0.059 0.079 0.098 0.118 0.138
0.197 0.024 0.043 0.063 0.083 - - -
0.236 0.035 0.055 0.075 0.094 - - -
0.268 0.043 0.063 0.083 0.102 - - -
0.315 0.055 0.075 0.094 0.114 - - - 30°
0.335 0.063 0.083 0.102 0.122 - - -

Zd
0.394 0.079 0.098 0.118 0.138 0.157 0.177 0.197

C
0.402 0.083 0.102 0.122 0.142 0.161 0.181 0.201
0.472 0.102 0.122 0.142 0.161 0.181 0.201 0.220
ød
0.551 0.146 0.165 0.185 0.205 0.224 0.244 0.264
0.630 0.165 0.185 0.205 0.224 0.244 0.264 0.283
0.689 0.193 0.213 0.232 0.252 0.272 0.291 0.311
0.787 0.205 0.224 0.244 0.264 0.283 0.303 0.323
0.827 0.240 0.260 0.280 0.299 0.319 0.339 0.358
0.945 0.307 0.327 0.346 0.366 0.386 0.406 0.45
Tool: ECC31005R-60
1.181 0.343 0.362 0.382 0.402 0.421 0.441 0.461 Note: When the hole depth is smaller than the Z-axis
1.299 0.374 0.394 0.413 0.433 0.453 0.472 0.492 plunging depth (Zd), special care should be
taken to avoid an interference between the
1.417 0.398 0.417 0.437 0.457 0.476 0.496 0.516
tool's front end and the bottom of the hole.
1.654 0.441 0.461 0.480 0.500 0.520 0.539 0.559
1.811 0.488 0.508 0.528 0.547 0.567 - -
1.890 0.512 0.531 0.551 0.571 - - -
2.047 0.555 - - - - - -

Z-axis plunging depth Zd (in) in 60° chamfering of hole

Hole dia.ød (in) Size of chamfering C (in)
0.020 0.039 0.059 0.079 0.098 0.118 0.138 0.157
0.197 0.031 0.051 0.071 0.091 0.110 - - -
0.236 0.067 0.087 0.106 0.126 0.146 - - -
0.268 0.094 0.114 0.134 0.154 0.173 - - -
0.315 0.134 0.154 0.173 0.193 0.213 - - - 60°
0.335 0.150 0.169 0.189 0.209 0.228 - - -
0.394 0.201 0.220 0.240 0.260 0.280 0.299 0.319 0.339
Zd

0.402 0.209 0.228 0.248 0.268 0.287 0.307 0.327 0.346

C

0.472 0.272 0.291 0.311 0.331 0.350 0.370 0.390 0.409

0.551 0.406 0.425 0.445 0.465 0.484 0.504 0.524 0.543 ød
0.630 0.457 0.476 0.496 0.516 0.535 0.555 0.575 0.594
0.689 0.539 0.559 0.579 0.598 0.618 0.638 0.657 0.677 Tool: ECC31005R-30
0.787 0.575 0.594 0.614 0.634 0.654 0.673 0.693 0.713 Note: When the hole depth is smaller
0.827 0.677 0.697 0.717 0.736 0.756 0.776 0.795 0.815 than the Z-axis plunging depth
0.945 0.882 0.902 0.921 0.941 0.961 0.980 1.000 - (Zd), special care should be
1.181 0.980 1.000 - - - - - - taken to avoid an interference
between the tool's front end and
the bottom of the hole.

Tungaloy D207
Multi Function E C P4400R
I n d ex a b l e c h a m f e r i n g c u t te r w i t h s q u a re i n s e r t

øDsh6
øDc
øD1
Rs
45˚
L

Inch øDc z øD1 øDs L ℓs Insert

ECP440AR-U 0.394 1 1.083 1.250 4.50 2.48 SPMA422*N
ECP4423R-U 0.906 2 1.587 1.250 4.50 2.48 SPMA422*N
ECP4436R-U 1.417 3 2.098 1.250 4.50 2.48 SPMA422*N

Metric øDc z øD1 øDs L ℓs Insert

ECP440AR 10 1 27.5 32 130 80 SPMA422*N
ECP4423R 23 2 40.3 32 130 80 SPMA422*N
ECP4436R 36 3 53.3 32 130 80 SPMA422*N

SPARE PARTS
Designation Clamping screw Wrench
ECP44... CSTA-4 T-15D

INSERT
SP M A 42
rε
11°
B

A T
P Steel  
M Stainless
K Cast iron 
N Non-ferrous
S Superalloys : First choice
H Hard meterials : Second choice
Cermet Uncoated
NS740

Designation rε A B T
UX30
TH10

SPMA422TN 0.031 z z 0.500 0.500 0.215

SPMA422FN 0.031 z 0.500 0.500 0.215
z: Line up
STA NDA RD CUT TING CONDITIONS
Maximum
Cutting speed Feed per tooth
Operations Workpiece material Grade depth of cut
Vc (sfm) fz (ipt)
ap (in)
Single or double chamfering hole chamfering Carbon steels, Alloy steels NS740 · N308
330 - 490 - 0.008 - 0.029
< 300HB UX30
Die steels NS740 · N308
164 - 230 - 0.006 -0.016
< 30HRC UX30

Cast irons TH10 90 - 110 - 0.008 - 0.024

Facing Grooving Carbon steels, Alloy steels NS740 · N308

330 - 490 0.118 0.004 - 0.006
< 300HB UX30
Die steels
UX30 164 - 230 0.079 0.004 - 0.006
< 30HRC

Cast irons TH10 295 - 360 0.118 0.004 - 0.006

Notes:
• When chamfering stainless steel, down-milling is recommended. Conventional milling may cause edge chipping.
• When chamfering above C3.0, the feed per tooth should be set at the lower side of the value shown in the above table.

D208 www.tungaloyamerica.com
TC B

Multi Function
I n d ex a b l e c o u n te r b o r i ng end m i l l

(Min. pre-hole

øDsh6
diameter)
øDi
Ltm

øDc
90° ş1 şs
L

Metric øDc z øDi ℓ1 Ltm L ℓs øDs Insert

TCB100F16 10 1 2.8 13 17 86 60 16 SPMP771...
TCB110F16 11 1 2.8 14 18.7 87 60 16 SPMP771...
TCB120F20 12 1 3.6 15 20.5 89 60 20 SPMP771...
TCB130F20 13 2 4.5 16 22.2 91 60 20 SPMP771...
TCB-140 14 1 4 11 18 117 80 25 SPMP831...
TCB140F25 14 2 5.5 18 24 113 80 25 SPMP771...
TCB150F25 15 2 6.5 19 25.7 114 80 25 SPMP771...
TCB160F25 16 2 7.5 20 27.5 116 80 25 SPMP771...
TCB170F25 17 2 6.6 13 21 114 80 25 SPMP831...
TCB175F25 17.5 2 7.1 14 22 115 80 25 SPMP831...
TCB180F25 18 2 7.5 15 23 116 80 25 SPMP831...
TCB190F25 19 2 8.5 15 24 118 80 25 SPMP831...
TCB-200 20 2 8.2 16 25 120 80 25 SPMP042...
TCB200F25 20 2 8.2 16 25 120 80 25 SPMP042...
TCB210F25 21 2 9 17 26 122 80 25 SPMP042...
TCB220F25 22 2 10 18 28 124 80 25 SPMP042...
TCB-230 23 2 11 19 29 126 80 25 SPMP042...
TCB230F25 23 2 11 19 29 126 80 25 SPMP042...
TCB240F25 24 2 12 20 - 128 80 25 SPMP042...
TCB250F25 25 2 13 25 - 130 80 25 SPMP042...
TCB-260 26 2 14 21 33 132 80 32 SPMP042...
TCB-290 29 2 14 23 36 138 80 32 SPMM322...
TCB-320 32 2 16.9 40 - 144 80 32 SPMM322...
TCB-350 35 2 14 43 - 150 80 32 SPMM432...
TCB-390 39 2 17.9 48 - 158 80 32 SPMM432...
TCB-430 43 2 21.7 53 - 171 85 42 SPMM432...
TCB-... : Existing items with black oxide
TCB**F... : New items with nickel plating
Applicable tolerance
Tool diameter tolerance range of hole diameter
+0.2 / 0 +0.3 / 0

Counter sink dimensions of bolt hole

øD
H

ød Thread size M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27
øD (mm) 11 14 17.5 20 23 26 29 32 35 39 43
H (mm) 6.5 8.6 10.8 13 15.2 17.5 19.5 21.5 23.5 25.5 29
ød (mm) 6 9 11 14 16 18 20 22 24 26 30
Applicable tool TCB110 TCB140 TCB175 TCB200 TCB230 TCB260 TCB290 TCB320 TCB350 TCB390 TCB430

SPARE PARTS
Designation Clamping screw Wrench
TCB100... - TCB160... CSTB-2L040 T-6D
TCB-140... CSTB-2.2S T-7D
TCB170... - TCB190... CSTB-2.2 T-7D
TCB200... - TCB260... CSTA-NO3 T-9D
TCB-290 - TCB-320 CSTA-NO5 T-9D Reference pages
TCB-350 - TCB-430 CSTA-4 T-15D
Inserts, Standard cutting conditions → D210

Tungaloy D209
 INSERT
Multi Function S PM P/SP M M
rε

11°
A T

P Steel 
M Stainless 
K Cast iron 
N Non-ferrous
S Superalloys : First choice
H Hard meterials : Second choice
Coated

Designation rε T313W A T

SPMP831DS 0.016 z 0.250 0.094

SPMP042ERD 0.031 z 0.313 0.125
SPMM322ERD 0.031 z 0.375 0.125
SPMM432ERD 0.031 z 0.500 0.187
z: Line up

STA NDA RD CUT TING CONDITIONS

Cutting speed Feed
ISO Workpiece material Grade Cutting fluid
Vc (sfm) f (ipr)

Carbon steels T313W 260 - 490 0.005 -0.009 Water soluble type

Stainless steels, Mild steels T313W 490 - 560 0.002 - 0.005 Water soluble type

Cast irons T313W 230 - 430 0.008 - 0.016 Water soluble type or dry cutting

Notes :
• For cutters under 0.787" diameter, be sure to use a cutting fluid and select lower cutting speeds than shown above.
• For TCB-140 type, reduce the feeds to 1/2 of the values shown in the table.

D210 www.tungaloyamerica.com
Sin gl e toot h thread i ng mi l l s
I n d ex a b l e t h re a d i ng m i l l s

Multi Function
øDc

øDs
Lf
L
Right hand, 4 inserts shown

Metric øDc z øDs Lf L Range of internal thread Insert

D23-D25-45R 23 1 25 45 115 M28 - M30 T1-R...
D25-D25-45R 25 1 25 45 115 M32 - M42 T1-R...
D38-D32-85R 38 2 32 85 165 M45 - M56 T1-R...
D50-D42-100R 50 4 42 100 190 M58 - M68 T1-R...
D55-D42-100R 55 4 42 100 190 M64 - M85 T2-R...
D60-D42-100R 60 4 42 100 190 M70 - M85 T2-R...
D80-D42-100R 80 6 42 100 190 M90 - T2-R...

SPARE PARTS
Designation Clamping screw Wrench
D23-D25... - D50-D42... CSTB-4 T-15F
D55-D42... - D80-D42... CSTB-5 T-20F

INSERT
T *-R . . .
60°
rε
B

A T

P Steel 
M Stainless 
K Cast iron
N Non-ferrous
S Superalloys : First choice
H Hard meterials : Second choice
Coated
GH330

Designation rε A B T

T1-R14 0.006 z 0.567 0.375 0.187

T1-R28 0.011 z 0.567 0.375 0.187
T2-R14 0.006 z 0.701 0.500 0.250
T2-R28 0.011 z 0.701 0.500 0.250

z: Line up
STA NDA RD CUT TING CONDITIONS
Cutting speed Feed per tooth
ISO Workpiece material Grade
Vc (sfm) fz（ipt）
Mild steels / Unharded steels < 200HB GH330 490 - 660 0.012 - 0.016

Carbon steels / Alloy steels < 300HB GH330 490 - 660 0.007 - 0.010

Die steels < 50HRC GH330 100 - 160 0.006 - 0.008

Stainless steels < 300HB GH330 490 - 660 0.002 - 0.005

• Climb milling is recommended.

• When threading a blind hole, use the right hand cutter in right-hand rotation. Cut up from the bottom to prevent chip recutting.
• When machining internal threads from the mouth, use the left-hand cutter in left-hand rotation.

Tungaloy D211
 Milling Inse r t
 ACMT**PR-MJ
Coated
Applicable

GH330
AH120
AH140
Shape Designation

T3130
mills

ACMT060308PR-MJ z z z z ELP07/09/12...
ACMT07T308PR-MJ z z z z
Rake angle Land width ACMT100408PR-MJ z z z z
Insert

-MJ

 ADMT**PR-MJ
Coated
Applicable

AH120
AH140
Shape Designation

T3130
mills

ADMT130308PR-MJ z z z ELP13/17/21...
ADMT17T308PR-MJ z z z
Rake angle Land width ADMT210408PR-MJ z z z

-MJ

 AECW**PEFR, AECW**PESR, AEMW**PEFR, AEMW**PETR

Coated Cermet Uncoated
Applicable
GH330
AH120

NS740

Shape Designation
UX30
TH10 mills

AECW1403PEFR z
EPE4000/5000/
AECW1403PESR z z z z 6000...
AECW16T3PEFR z
AECW16T3PESR z z z z
AECW1804PEFR z
AECW1804PESR z z z z
AEMW1403PEFR z
AEMW1403PETR z z z
AEMW16T3PEFR z
AEMW16T3PETR z z z
AEMW1804PEFR z
AEMW1804PETR z z z

 ANEA542TN, ANEA642TN
Uncoated
Applicable
Shape Designation
UX30

mills

ANEA542TN  VSN...
ANEA642TN  (Former products)

●： Line up

D212 www.tungaloyamerica.com
 Milling Inse r t
 ANMT**PPPR-MJ, ANMT**PPPR-ML
Coated
Applicable

GH330
AH120
Shape Designation

T3130
mills

ANMT09T3PPPR-MJ    EPN09
ANMT09T3PPPR-ML  (Former products)
ANMT1404PPPR-MJ   

Insert
Rake angle Land width EPN14...
ANMT1404PPPR-ML  TPN14...
(Former products)
-MJ

Land width
Rake angle

-ML

 AOMT**PDPR-MJ, AOGT**PDFR-AJ, AOMT070208PDPR-HJ

Coated Uncoated
Applicable
AH725
AH140

KS15F

Shape Designation
mills

AOMT070202PDPR-MJ z z
AOMT070204PDPR-MJ z z TPO07...
Rake angle Land width AOMT070208PDPR-MJ z z Page D054

AOMT070216PDPR-MJ z z EPO07...
AOMT070208PDPR-HJ z z Page D054

-MJ AOGT070204PDFR-AJ z HPO07...

Page D055

Rake angle Land width

-HJ

Rake angle

-AJ

●： Line up

Tungaloy D213
 Milling Inse r t
 AOMT**PDPR-MJ, AOGT**PDFR-AJ
Coated Uncoated
Applicable

AH725
AH140

KS15F
Shape Designation
mills

AOMT180508PDPR-MJ z z
AOMT180516PDPR-MJ z z TPO18...
Rake angle Land width AOMT180524PDPR-MJ z z Page D065
Insert

AOMT180532PDPR-MJ z z EPO18...
AOGT180504PDFR-AJ z Page D066
-MJ
AOGT180508PDFR-AJ z

Rake angle

-AJ

 APMT**PN-MJ
Coated
Applicable
GH330
AH120
AH140

Shape Designation
T3130

mills

APMT070308PN-MJ z z z z ELP07/09/12...
APMT09T308PN-MJ z z z z
Rake angle Land width
APMT120408PN-MJ z z z z

-MJ

 APMT120416PR-MJ
Coated
Applicable
AH120

Shape Designation
T3130

mills

APMT120416PR-MJ z z TZP12...

Rake angle Land width

-MJ

●： Line up

D214 www.tungaloyamerica.com
Milling Inse r t
 APMR190616PR-MJ
Coated
Applicable

AH120
Shape Designation

T3130
mills

APMR190616PR-MJ z z TZP19...

Insert
Rake angle Land width

-MJ

 ASMT**PDPR-MJ, ASGT11**PDFR-AJ, ASMT11T304PDPR-MS

Coated Cermet Uncoated
Applicable

DS1100

KS05F
AH725
AH130
AH120

AH140

NS740
Shape Designation

T3130
T1215
T1115
mills

ASMT11T304PDPR-MJ z z z z z z
ASMT11T308PDPR-MJ z z z z z z z z TPS11...
Rake angle Land width
ASMT11T312PDPR-MJ z z z z z Page D058

ASMT11T316PDPR-MJ z z z z z TLS11...
ASMT11T320PDPR-MJ z z Page D059

-MJ
ASMT11T330PDPR-MJ z z EPS11...
ASMT11T304PDPR-MS z z Page D058

ASGT11T304PDFR-AJ z z HPO11...
ASGT11T308PDFR-AJ z z Page D060
Rake angle Land width
ELS11...
Page D059

-MS

Rake angle

-AJ

●： Line up

Tungaloy D215
 Milling Inse r t
 ASMT17**PDPR-MJ, ASGT17**PDFR-AJ, ASMT170508PDPR-MS
Coated Cermet Uncoated

DS1100
Applicable

AH120
AH130
AH140

KS05F
NS740
Shape Designation

T1115
T3130
mills

ASMT170504PDPR-MJ z z z z z TPS17...
ASMT170508PDPR-MJ z z z z z z Page D089

ASMT170512PDPR-MJ z z z EPS17...
Insert

Rake angle Land width

ASMT170516PDPR-MJ z z z Page D089

ASMT170520PDPR-MJ z
-MJ ASMT170530PDPR-MJ z
ASMT170532PDPR-MJ z z z
ASMT170508PDPR-MS z z
Rake angle Land width
ASGT170504PDFR-AJ z z
ASGT170508PDFR-AJ z z

-MS

Rake angle

-AJ

 AVGT**PBER-MJ, AVGT**PBFR-AJ
Coated Uncoated
AH3135

Applicable
KS05F
AH120

Shape Designation
mills

AVGT060302PBER-MJ z z
AVGT060304PBER-MJ z z EPAV...
Rake angle AVGT060308PBER-MJ z z Page D050

AVGT060302PBFR-AJ z HPAV06...
AVGT060304PBFR-AJ z Page D050

-MJ AVGT060308PBFR-AJ z

Rake angle

-AJ

●： Line up

D216 www.tungaloyamerica.com
Milling Inse r t
 CPMW**-EN, CPMT**-EN
Coated Uncoated
Applicable

GH330
Shape Designation

UX30
mills

CPMW050208EN   EVP1000
CPMW06T208EN   (Former products)
CPMT080308EN  

Insert
 DCMW**TN
Coated
Applicable

AH330
Shape Designation AH120
mills

DCMW070204TN z z EBP... Page D164

DCMW11T304TN z z HBP...

 DPCW11T3ZFR
Coated Cermet
Applicable
AH740

NS740

Shape Designation
mills

DPCW11T3ZFR z z TZF11...
HZF11...

 EDKW53ZTR
Coated Uncoated
Applicable
GH330

Shape Designation
UX30

mills

EDKW53ZTR   ESD5000
(Former products)

●： Line up

Tungaloy D217
 Milling Inse r t
 ENEQ**TN-T
Coated
Applicable

AH120
Shape Designation
mills

ENEQ090508TN-T  VSNE09... (Former products)

ENEQ100508TN-T  VSNE10... (Former products)

ENEQ130608TN-T  VSNE13... (Former products)

Insert

ENEQ160608TN-T  VSNE16... (Former products)

 GDMT**PDPR-MJ, GDGT**PDFR-AJ
Coated Uncoated

DS1100
Applicable
AH120
AH140
AH330
Shape Designation

T3130

UX30
TH10
mills

GDMT10H3PDPR-MJ z z z z z TSD10/17...
GDMT17X6PDPR-MJ z z z z z ESD10/17...
GDGT10H3PDFR-AJ z z HSD10/17...
Rake angle Land width
GDGT17X6PDFR-AJ z z

-MJ

Rake angle

-AJ

 HEHN532FN
Uncoated
Applicable
Shape Designation
TH10

mills

HEHN532FN  QYE5300
(Former products)

●： Line up

D218 www.tungaloyamerica.com
Milling Inse r t
 HPKN532FN
Uncoated
Applicable
Shape Designation

TH10
mills

HPKN532FN  QYP5300
(Former products)

Insert
 LMEU**ZNEN-MJ
Coated
Applicable
AH120
AH140
AH725
Shape Designation
mills

z z z TEC TSlot
a n g e n t i a l

LMEU100808ZNEN-MJ
LMEU100816ZNEN-MJ z z z ASN 10/12/15...
LMEU100824ZNEN-MJ z z z Page D136

LMEU100832ZNEN-MJ z z z TSN 10/12/15...

LMEU120808ZNEN-MJ z z z Page D137

LMEU120816ZNEN-MJ z z z
Rake angle
LMEU120824ZNEN-MJ z z z
LMEU120832ZNEN-MJ z z z
-MJ LMEU150908ZNEN-MJ z z z
LMEU150916ZNEN-MJ z z z
LMEU150924ZNEN-MJ z z z
LMEU150932ZNEN-MJ z z z

 LMMU**PNER-MJ
Coated
Applicable
AH120
AH140
AH725

Shape Designation
mills

LMMU110708PNER-MJ z z z
LMMU110716PNER-MJ z z z TPM11/16...
LMMU110724PNER-MJ z z z Page D079
Land width
Rake angle
LMMU110732PNER-MJ z z z TLM11...
LMMU160908PNER-MJ z z z Page D080

LMMU160916PNER-MJ z z z EPM11...
LMMU160924PNER-MJ z z z Page D079
-MJ
LMMU160932PNER-MJ z z z
●： Line up

Tungaloy D219
 Milling Inse r t
 LNCA64ZTR
Coated Uncoated
Applicable
Shape Designation

T3130

UX30
mills

LNCA64ZTR   VSN6000I
(Former products)
Insert

 LNCQ0906N-**L, LNCQ0906R-50S
Coated Cermet
Applicable

GH110
AH120

NS740
Shape Designation
mills

LNCQ0906N-100L z z z NMS09...
LNCQ0906N-50L z z z EMS09...
LNCQ0906R-50S z z z
Rake angle

 LNMU0303ZER-MJ, LNMU0303ZER-ML
Coated
AH3035
AH8015

Applicable
AH725
AH130

Shape Designation
mills

LNMU0303ZER-MJ z z z z
LNMU0303ZER-ML z z z z TXN03...
Rake angle Land width Page D008

EXN03...
Page D008

-MJ HXN03...
Page D009

Land width
Rake angle

-ML

●： Line up

D220 www.tungaloyamerica.com
Milling Inse r t
 LNMU06X5ZER-MJ, LNMU06X5ZER-ML, LNGU06X5ZER-W
Coated

AH3035
AH8015
Applicable

AH725
AH130
AH120
Shape Designation
mills

LNMU06X5ZER-MJ z z z z z
LNMU06X5ZER-ML z z z z z TXN06...
Rake angle Land width LNGU06X5ZER-W z Page D012

Insert
EXN06...
Page D013

-MJ

Rake angle Land width

-ML

-W

 LNMX0405R4-MJ, LNMX0405R4-ML, LNMX0405R4-HJ

Coated
AH3135

Applicable
AH120

Shape Designation
mills

LNMX0405R4-MJ z z
LNMX0405R4-ML z z TXLN... Page D016

Rake angle
Land width LNMX0405ZER-HJ z z EXLN... Page D016

HXLN... Page D017

-MJ

Rake angle Land width

-ML

Rake angle Land width

-HJ

●： Line up

Tungaloy D221
 Milling Inse r t
 LQMU**PNER-MJ
Coated
Applicable

AH120
AH140
AH725
Shape Designation
mills

LQMU110704PNER-MJ z z z
LQMU110708PNER-MJ z z z TPQ11/18...
LQMU110716PNER-MJ z z z Page D076
Insert

Land width
Rake angle LQMU180804PNER-MJ z z z EPQ11...
LQMU180808PNER-MJ z z z Page D077

LQMU180816PNER-MJ z z z
LQMU180824PNER-MJ z z z
-MJ

 ONMU0705ANPN-MJ, ONHU0705ANPN-MJ, ONMU0705ANPN-ML,

ONHU0705ANTN-ML, ONHU0705ANPR-W
Coated

AH3135
Applicable
AH120
AH140
Shape Designation AH725

T1115
T1215
mills

ONMU0705ANPN-MJ z z z z z
ONHU0705ANPN-MJ z z
Rake angle Land width ONMU0705ANPN-ML z z TAN07...
ONHU0705ANTN-ML z z z Page D101

ONHU0705ANPR-W z
-MJ

Rake angle Land width

-ML

-W

●： Line up

D222 www.tungaloyamerica.com
Milling Inse r t
 ONGU0507ANEN-MJ, ONGU0507ANEN-W, ONMU0507ANEN-MJ
Coated

AH3135
Applicable

AH120
Shape Designation

T3225
T1215
mills

ONGU0507ANEN-MJ z z z
ONGU0507ANEN-W z z TASN13...
Land width ONMU0507ANEN-MJ z z z z Page D098

Insert
Rake angle

-MJ

Rake angle Land width

-W

 OWMT0807ZNER-HJ, OWMT0807AAER-ML
Coated
AH3135

Applicable
AH130

Shape Designation
mills

OWMT0807ZNER-HJ z
OWMT0807AAER-ML z z
Rake angle Land width TAN07...
Page D101

-HJ

Rake angle Land width

-ML

●： Line up

Tungaloy D223
 Milling Inse r t
 PNCU0905GNER-MJ, PNCU0905GNEN-ML, PNCU0905GNFR-AJ,
PNMU0905GNEN-MJ, PNCU0905GNER-W
Coated Cermet Uncoated

AH3135
Applicable

AH120
AH140
AH725

NS740
Shape Designation

T1115
T1215
T3130

TH10
mills

PNCU0905GNER-MJ z z z z z z
PNCU0905GNEN-ML z TEN09R...
PNCU0905GNFR-AJ z Page D106
Insert

Rake angle Land width

PNMU0905GNEN-MJ z z z EEN09...
PNCU0905GNER-W z Page D107

-MJ

Rake angle Land width

-ML

Rake angle

-AJ

-W

●： Line up

D224 www.tungaloyamerica.com
Milling Inse r t
 RCMT**EN-MJ, RCMT**EN-NMJ, RCMT**FN-NAJ
Coated Uncoated
Applicable

AH725
AH120
AH140

KS15F
Shape Designation
mills

RCMT1204EN-MJ z z z
RCMT1204EN-NMJ z z z TRC12/16...
RCMT1204FN-NAJ z Page D155

Insert
Rake angle Land width
RCMT1606EN-MJ z z z ERC12/16...
RCMT1606EN-NMJ z z z Page D156

-MJ RCMT1606FN-NAJ z

Rake angle

-NMJ

Rake angle

-NAJ

 RDCA2004TN, RDCN2004TN, RDKN2004...

Coated Uncoated
Applicable
AH120

Shape Designation
UX30
TH10

mills

RDCA2004TN z TRD6000
RDCN2004TN z ERD6000
RDKN2004FN z
RDKN2004TN z z

 RDCM1203TN, RDMA1203TN
Uncoated
Applicable
Shape Designation
UX30

mills

RDCM1203TN  ERD4000
RDMA1203TN  (Former products)

●： Line up

Tungaloy D225
 Milling Inse r t
 RDMT**ZDPN-MJ, RDMW**ZDSN
Coated Uncoated
Applicable

AH120
AH130
AH140
AH330
Shape Designation

T3130
UX30
mills

RDMT1204ZDPN-MJ z z z z z TRD12/16...
RDMW1204ZDSN z Page D159

Rake angle Land width RDMT1606ZDPN-MJ z z z z z z ERD12...

Insert

RDMW1606ZDSN z Page D160

-MJ

 RDMW**M0
Coated
Applicable
AH120

Shape Designation
mills

RDMW0501M0 z EWD05/07/10...
RDMW0702M0 z Page D162

RDMW1003M0 z HWD07...
Page D162

 RFEN2004ZFTN, RFEN2004M0TN
Coated Uncoated
Applicable
GH330
AH120

Shape Designation
UX30
KS20

mills

RFEN2004ZFTN z z z z TRF6000
RFEN2004M0TN z z z ERF6000

 RNGU1307ZNER-MJ, RNMU1307ZNER-MJ
Coated
AH3135

Applicable
AH120

Shape Designation
T1215
T3225

mills

RNGU1307ZNER-MJ z z
RNMU1307ZNER-MJ z z z z TASN13...
Page D098
Rake angle Land width

-MJ

●： Line up

D226 www.tungaloyamerica.com
Milling Inse r t
 RPMT**EN-MJ, RPMT**EN-ML
Coated

AH4035
Applicable

AH130
AH725
Shape Designation
mills

RPMT10T3EN-MJ z z z
RPMT10T3EN-ML z z z TRP12/16...
Rake angle Land width RPMT1204EN-MJ z z z Page D150

Insert
RPMT1204EN-ML z z z ERP10/12/16...
RPMT1606EN-MJ z z z Page D150
-MJ
RPMT1606EN-ML z z z HRP10/12...
Page D151

Rake angle Land width

-ML

 SCMT**-23
Coated
Applicable
AH120

Shape Designation
mills

SCMT09T308-23 z EBD... Page D166

SCMT120408-23 z HBD...
Rake angle

-23

 SDCN1504ZDSR, SDEN1504ZDSR, SDNN1504ZDSR

Coated
Applicable
AH120
AH140

Shape Designation
T3130
T1115

mills

SDCN1504ZDSR z z z
SDEN1504ZDSR z z z z TXD15...
SDNN1504ZDSR z z z z

●： Line up

Tungaloy D227
 Milling Inse r t
 SDCN42HTR, SDKN42HTR
Coated
Applicable

GH330
Shape Designation
mills

SDCN42HTR  EUD4600
SDKN42HTR  (Former products)
Insert

 SDKN42EF..., SDEN42EFTR24
Coated Cermet Uncoated
Applicable

NS740
Shape Designation
T3130

UX30
TH10
mills

SDKN42EFTR   TMD4100I
SDKN42EFFR  (Former products)
SDEN42EFTR24  

 SDCN42Z..., SDEN42Z..., SDKN42Z..., SDCN42ZFN-DIA, SDKR42ZSR-MJ,

SDMR1203AETN-MJ, SDKR1203AETN-MJ, SDKR42ZPN-MS
Coated Cermet Uncoated PCD
Applicable
GH330
AH120
AH130
AH140
AH330

DX140
NS740

Shape Designation
T1115
T3130

UX30
TH10
N308

mills

SDCN42ZFN z TMD4400RI-U
SDCN42ZTN z z z Page D120

SDCN42ZTN20 z TMD4400RB-U
SDEN42ZFN z Page D121

SDEN42ZTN z z z z z z z EMD4400RI
SDEN42ZTNCR z z z z TGD4400-A
Rake angle Land width
SDEN42ZTN20 z EGD4400
SDKN42ZFN z TFD4400-A
SDKN42ZTN z z z z z z z z z
-MJ
SDKN42ZTNCR z
Rake angle Land width
SDKN42ZTN16 z
SDCN42ZFN-DIA z
SDKR42ZSR-MJ z z z z
-MS
SDMR1203AETN-MJ z
SDKR1203AETN-MJ z
SDKR42ZPN-MS z z
DX140：Packing quantity = 1pc.
●： Line up

D228 www.tungaloyamerica.com
Milling Inse r t
SDCN53HTR, SDKN53HTR
Coated

GH330
Applicable
Shape Designation
mills

SDCN53HTR  TUD5600
SDKN53HTR  (Former products)

Insert
 SDCN53ZTN, SDEN53Z..., SDKN53Z..., SDKR53ZSR-MJ
Coated Cermet Uncoated
Applicable

GH330
AH120
AH130
AH140

NS740
Shape Designation

T3130

UX30
TH10
N308
mills

SDCN53ZTN z z TMD5400I-U
SDEN53ZFN z Page D124

SDEN53ZTN z z z
SDEN53ZTNCR z
SDEN53ZTN20 z
Rake angle Land width
SDKN53ZFN z
SDKN53ZTN z z z z z z z
SDKN53ZTNCR z
-MJ SDKN53ZTN16 z
SDKR53ZSR-MJ z z

 SDMT050204PN-MJ, SDHT050204FN-AJ
Coated Uncoated
Applicable
AH725
AH140

Shape Designation
TH10

mills

SDMT050204PN-MJ z z
SDHT050204FN-AJ z TPD05...
Rake angle Page D069

EPD05...
Page D069

-MJ
ELD05...
Page D069

Rake angle

-AJ

●： Line up

Tungaloy D229
 Milling Inse r t
 SDMT1204AFPN-MJ, SDMT1204AFTN-MJ, SDMT1204AFPN-ML, SDMT1204AFPN-MS,
SDGT1204AFTN-MJ, SDGT1204AFFN-AJ
Coated Cermet Uncoated

Applicable

GH330
AH120
AH140
AH330

NS740
Shape Designation

T3130

TH10
mills

SDMT1204AFPN-MJ      TAD12...
SDMT1204AFTN-MJ  EAD12...
  (Former products)
Insert

Rake angle Land width SDMT1204AFPN-ML

SDMT1204AFPN-MS 
SDGT1204AFTN-MJ   
-MJ SDGT1204AFFN-AJ 

Rake angle

-AJ
Rake angle Land width

-ML
Rake angle Land width

-MS

 SDMT1204PDSR-MJ, SDMT1204PDTR-MJ, SDMT1204PDPR-ML, SDMT1204PDPR-MS

SDGT1204PDTR-MJ, SDGT1204PDFR-AJ
Coated Cermet Uncoated

Applicable
GH330
AH120
AH140
AH330

NS740

Shape Designation
T3130

TH10

mills

SDMT1204PDSR-MJ      TPD12...
SDMT1204PDTR-MJ  EPD12...
Rake angle Land width SDMT1204PDPR-ML   (Former products)
SDMT1204PDPR-MS 
SDGT1204PDTR-MJ   
-MJ SDGT1204PDFR-AJ 

Rake angle

-AJ
Rake angle Land width

-ML
Rake angle Land width

-MS

●： Line up

D230 www.tungaloyamerica.com
Milling Inse r t
 SDMW090308TN, SDMW120408TN
Uncoated
Applicable
Shape Designation

UX30
mills

SDMW090308TN  ELD3000
SDMW120408TN  ELD4000
(Former products)

Insert
 SECN1203AGFN, SEEN1203AG..., SEKN1203AG..., SEKR1203AGSR-MJ, SEKR1203AGPN-MS
Coated Cermet Uncoated
Applicable

GH330
AH120
AH130
AH140
AH330

NS740
Shape Designation

T1115
T3130

UX30
TH10
mills

SECN1203AGFN z TME4400R/LI
SEEN1203AGFN z TME4400RB
SEEN1203AGTN z z z z z z z EME4400
SEEN1203AGTN-T z z z
SEEN1203AGTNCR z z z z z
SEEN1203AGTNCR-14 z
Rake angle Land width
SEKN1203AGFN-T z
SEKN1203AGTN z z z z z z z z
SEKN1203AGTN-T z z z z z
-MJ
SEKN1203AGTNCR z
SEKR1203AGSR-MJ z z z z
SEKR1203AGPN-MS z z
Rake angle Land width

-MS

 SE*N1504AG..., SEKR1504AGSR-MJ
Coated Cermet Uncoated
Applicable
GH330
AH120
AH140

NS740

Shape Designation
T3130

UX30
TH10

mills

SEEN1504AGTN z z TME5400RI
SEKN1504AGFN z
SEKN1504AGTN z z z z z z
SEKN1504AGTN-T z z
SEKR1504AGSR-MJ z z

Rake angle Land width

-MJ

●： Line up

Tungaloy D231
 Milling Inse r t
 SECN422TN, SECN422FN, SEEN422TN, SEEN422FN, SECN422FN-DIA
Cermet Uncoated PCD
ISO Designation Applicable

NS740

DX140
Shape Designation

UX30
N308

TH10
(Metric) mills

SECN422TN SECN120308TN    EGE4000

SECN422FN SECN120308FN  (Former products)
SEEN422TN SEEN120308TN    QHE4000
Insert

SEEN422FN SEEN120308FN 
SECN422FN-DIA SECN120308FN-D 

-DIA

DX140：Packing quantity = 1pc.

 SEEN1203AFTNCR-14, SEKN42AFTN, SEKN42AFFN, SEKN42AFTN16, SEKR42AFSR-MJ,

SEKR1203AFPN-MS, SEKR1203AFTN-MJ, SEMR1203AFTN-MJ
Coated Cermet Uncoated
ISO Designation Applicable

GH330
AH120
AH130
AH140

NS740
Shape Designation

T3130

UX30
TH10
(Metric) mills

SEEN1203AFTNCR-14  TGE4400I
SEKN42AFTN SEKN1203AFTN      EGE4400
SEKN42AFFN SEKN1203AFFN  (Former products)
SEKN42AFTN16 SEKN1203AFTN-16  
SEKR42AFSR-MJ SEKR1203AFSR-MJ  
Rake angle Land width
SEKR1203AFPN-MS 
SEKR1203AFTN-MJ 
SEMR1203AFTN-MJ 
SEKR-MJ

Rake angle Land width

SEMR-MJ

Rake angle Land width

-MS

●： Line up

D232 www.tungaloyamerica.com
Milling Inse r t
 SECN42EFTRCR, SEEN42EFTRCR, SEKN42EFTR, SEKN42EFFR
Coated Cermet Uncoated
ISO Designation Applicable

GH330

NS740
Shape Designation

T3130

UX30
TH10
(Metric) mills

SECN42EFTRCR SECN1203EFTR  EGE4100

SEEN42EFTRCR SEEN1203EFTR  (Former products)
SEKN42EFTR SEKN1203EFTR   

Insert
SEKN42EFFR SEKN1203EFFR 

 SE*N42ZFR, SECN42ZFR-DIA
Uncoated PCD
Applicable

DX140
Shape Designation
TH10
mills

SECN42ZFR-DIA z THE4000RIA
SECN42ZFR z
SEEN42ZFR z

-DIA
DX140：Packing quantity = 1pc.
●： Line up

Tungaloy D233
 Milling Inse r t
 SEGW12X4ZEFR, SEGW12X4ZEPR, SEGT12X4ZEFR-AJ, SEGW12X4ZEFR-D,
SEGW12X4ZEFR-WD, SEGW12X4ZEFR-BD
Coated Cermet Uncoated PCD

DS1100
Applicable

AH120
AH140

KS05F

DX140
NS740
Shape Designation
mills

SEGW12X4ZEFR z TFE12R...
SEGW12X4ZEPR z z z Page D114

SEGT12X4ZEFR-AJ z z EFE12RU...
Insert

SEGW12X4ZEFR-D z Page D114

SEGW12X4ZEFR-WD z
SEGW12X4ZEFR-BD z
Rake angle

-AJ

-D
(General insert)

-WD
(Wiper insert)

-BD
(Wiper insert)

DX140：Packing quantity = 1pc.

SEKR1504AFSR-MJ
Coated
Applicable
Shape Designation
T3130

mills

SEKR1504AFSR-MJ  (Former products)

Rake angle Land width

-MJ

●： Line up

D234 www.tungaloyamerica.com
Milling Inse r t
 SF*N42ZFN, SFCN42ZFN-DIA
Uncoated PCD
Applicable

DX140
Shape Designation

TH10
mills

SFCN42ZFN z THF4400RIA
SFEN42ZFN z
SFCN42ZFN-DIA z

Insert
-DIA

DX140：Packing quantity = 1pc.

 SF*N53ZFN, SFCN53ZFN-DIA
Uncoated PCD
Applicable
DX140
Shape Designation
TH10

mills

SFCN53ZFN z THF5400RIA
SFEN53ZFN z
SFCN53ZFN-DIA z

-DIA

DX140：Packing quantity = 1pc.

 SN**56FTR
Cermet
Applicable
Shape Designation
X407

mills

SNAA56FTR z MS...
SNAG56FTR
SNCC56FTR
SNCJ56FTR

●： Line up

Tungaloy D235
 Milling Inse r t
 SNCN43Z..., SNKF43Z..., SNKN43ZTN
Coated Cermet Ceramic Uncoated
Applicable

NS740
Shape Designation

FX105
T1115
T3130

UX30
TH10
N308
mills

SNCN43ZFN z TGN4200R-A
SNCN43ZTN z z z
SNKF43ZFN z
Insert

SNKF43ZTN z z
SNKN43ZTN z z z z z

 SNMU1706ANPR-MJ, SNHU1706ANPR-MJ, SNMU1706ANTR-ML, SNHU1706ANTR-ML,

SNHU1706ANFN-W
Coated

AH3135
Applicable
AH120
AH140
AH725
Shape Designation

T1215
mills

SNMU1706ANPR-MJ z z z z
SNHU1706ANPR-MJ z z
Rake angle Land width SNMU1706ANTR-ML z z TAN07...
SNHU1706ANTR-ML z Page D101

SNHU1706ANFN-W z
-MJ

Rake angle Land width

-ML

Rake angle Land width

-W

 SNEN12**Z...
Uncoated
Applicable
Shape Designation
UX30
TH10

mills

SNEN12T2ZFN z SVN4000
SNEN12T2ZTN z
Land width
SNEN1233ZFN z
Rake angle SNEN1233ZTN z

●： Line up

D236 www.tungaloyamerica.com
Milling Inse r t
 SNGU1307ANEN-MJ, SNGU1307ANEN-W, SNGU1307ANEN-MH,
SNGU1307C14ANEN-MJ, SNMU1307ANEN-MJ
Coated

AH3135
Applicable

AH120
Shape Designation

T3225
T1215
mills

SNGU1307ANEN-MJ z z z
SNGU1307ANEN-W z z TASN13...
Rake angle Land width SNGU1307ANEN-MH z Page D098

Insert
SNGU1307C14ANEN-MJ z z
SNMU1307ANEN-MJ z z z z
-MJ

-W

Rake angle Land width

-MH

Rake angle Land width

SNGU**C-MJ

 SNMN1204**TN
Coated Ceramic Uncoated
Applicable
AH120

Shape Designation
FX105
T1115
T3130

UX30

mills

SNMN120408TN z TGN4200R-A
SNMN120412TN z z z z z
SNMN120416TN z
SNMN120420TN z
SNMN120424TN z
●： Line up

Tungaloy D237
 Milling Inse r t
 SPCN42..., SPEN42..., SPKN42..., SPKR42SSR-MJ, SPGN120312TN
Coated Cermet Ceramic Uncoated
Applicable

GH330
AH120
AH140

NS740
Shape Designation

FX105
T1115
T3130

UX30
TH10
N308
mills

SPCN42STR z z z TGP4100RIA/BA
SPCN42SFR z
SPEN42STR z
Insert

SPKN42STR z z z z z z z z z
SPKN42STL z z
SPKN42SFR z
SPKN42SFL z
Rake angle Land width SPKR42SSR-MJ z z z
SPGN120312TN z
SPEN423TN z z z
-MJ SPEN423FN z

 SP*N42...
Coated Cermet Uncoated