KRONES Capping

Technology
Capper models for a wide range of
applications
2 ｜KRONES Capping Technology

Good and reliable capping

Beverage containers are used in various sizes and shapes

worldwide and accordingly there is great diversity in container
caps. With the KRONES cappers, you can reliably apply all
common cap types to containers.

At a glance:
− Wide portfolio
 Plastic screw caps
 Crowns and ring-pull caps
 Aluminium roll-on caps
 Press-on caps
− Suitable for both neck handling and base handling
3 ｜KRONES Capping Technology

Modulcap CM screw capper for plastic caps*

The KRONES Modulcap CM capper processes a large number of

plastic screw caps and applies them precisely on glass or PET
bottles even at high outputs.

Field of applications
Single-threaded and multi-threaded cap types**:
− Flat caps size range from 26 – 43 millimetres
− Rotationally symmetric sports caps

Output range
Up to 84,000 containers/h (depending on the cap type)

* C = Chucks, M = mechanical
** With corresponding change parts
4 ｜KRONES Capping Technology

Modulcap CM screw capper for plastic caps

Method of operation
The screw caps are spaced and oriented in the sorter, and then
fed to the capper from above. The chuck fixes the caps in the
capping head. A tension belt and centre starwheel are used to
prevent glass bottles and returnable PET containers from turning.
PET bottles are held in place by spikes on the neck starwheel.
The capping head applies the cap. The cap is pressed onto the
bottle by means of spring pressure. At the same time it is screwed
onto the thread of the bottle neck finish. As soon as the rotation
is ended and the required tightening torque is applied to the cap,
a hysteresis clutch ends the capping process. This clutch enables
smooth braking and a constant tightening torque at all filler
speeds.
5 ｜KRONES Capping Technology

Modulcap CM screw capper for plastic caps

Design features Machine pitch 87 94 103 113 126 141 188 226 283
− All main parts made of stainless steel AISI 304
− Height-adjustable pick station Pitch diameter (mm)
− Torque and press-on force of the capping head are 360 13 12 11 10 9 8 6 5 4
adjustable
540 – 18 – 15 – 12 9 – –
− Flushable chuck
720 26 24 22 20 18 16 12 10 –
− Replaceable chuck inserts
− Exchangeable spikes in neck support rings for PET 1080 39 36 33 30 27 24 18 15 –
bottles 1440 52 48 44 40 36 32 24 20 16
− Motorised height adjustment of the capper top part
with bottle selection feature
6 ｜KRONES Capping Technology

Modulcap CM screw capper for plastic caps

Additional equipment
− Separate capping head drive for multi-threaded caps
− Separate capping head drive for the same rotational speed at
different machine output levels
− Thread spraying and steaming
− Cap spraying and steaming
− Flushing equipment
− UV lamp for cap disinfection
− Dust blow-off with ionised air and suction
− Cap disinfection with H2O2 or peracetic acid
− Sorting systems with camera technology for cap inspection
prior to the application
7 ｜KRONES Capping Technology

Modulcap CM screw capper for plastic caps

Benefits to you

Caps are fitted perfectly

Use of a hysteresis clutch ensures screw caps are applied at a
constant force.

Can be optimally cleaned

The capping heads can be cleaned perfectly with hot water or
foam.
8 ｜KRONES Capping Technology

Modulcap CS* screw capper for plastic caps

The new generation of the servo motor screw capper Modulcap CS is

particularly convincing due to its hygienic design: As with proven
KRONES aseptic lines, all mechanical components are located above
the neck finish; bellows separate the mechanical environment from
the production environment. This allows the capper top to be
cleaned automatically via foam cleaning.

Field of applications
Single-threaded and multi-threaded cap types**:
− Flat caps size range from 26 – 43 millimetres
− Rotationally symmetric sports caps
− Press-on caps

Output range
Up to 84,000 containers per hour

* C = Chucks, S = servomotor
** With corresponding change parts
9 ｜KRONES Capping Technology

Modulcap CS screw capper for plastic caps

Method of operation
The screw caps are spaced and oriented in the sorter, and then
fed to the capper from above. The chuck fixes the caps in the
capping head. A tension belt and centre starwheel are used to
prevent glass bottles and returnable PET containers from turning.
PET bottles are held in place by spikes on the neck starwheel disk.

The capping head applies the cap. The cap is pressed onto the
bottle by means of spring pressure. At the same time it is
screwed onto the thread of the bottle neck finish. As soon as the
rotation is ended and the required tightening torque is applied to
the cap, the servo drive ends the capping process. This enables
smooth braking and a constant tightening torque at all filler
speeds. The required torque of the servo drives for the respective
cap to be processed will be automatically adjusted via type
management.
10 ｜KRONES Capping Technology

Modulcap CS screw capper for plastic caps

Design features Machine pitch 87 94 103 113 126 141 188 226 283
− Machine is constructed from a selection of stainless
steels optimised for relevant application Pitch diameter (mm)
− Complete cleaning and sterilisation possible
360 13 12 11 10 9 8 6 5 4
− Ceramic machine bearings
540 – 18 – 15 – 12 9 – 6
720 26 24 22 20 18 16 12 10 8
1080 39 36 33 30 27 24 18 15 12
1440 52 48 44 40 36 32 24 20 16
11 ｜KRONES Capping Technology

Modulcap CS screw capper for plastic caps

Drive system with servo motor Additional equipment

− Saving of data tracking and monitoring of screw-on values − CapAsept D: Cap disinfection system based on dry sterilisation
by continuous documentation within the servo control with hydrogen peroxide
− Optimum application of multi-threaded caps with stopped − CapAsept L: Cap disinfection system based on wet sterilisation
capping head with immersion bath
− Quick and hygienically safe adjustment of the tightening
torque without accessing the machine for cap change-over
− Realisation of different capping head rotational speeds at
different cap thread slants
− Permanent torque monitoring for even more precise screw-
on values
12 ｜KRONES Capping Technology

Modulcap CS screw capper for plastic caps

Benefits to you

Hygienically optimised design Can be optimally cleaned

The drives are positioned to reliably prevent germs from being The machine can be cleaned very effectively with foam and spray
spread into bottles while they are still open. disinfection. The open design of the pick station and chuck
ensures that individual parts are readily accessible.
Caps are fitted perfectly
The servo controller for the capping process precisely monitors Easy maintenance
the application torque. This ensures that screw caps are applied All component groups have a lubrication-free and maintenance-
at a constant force. free design

Reliable cap feed

The caps are hygienically conveyed to the pick station.
13 ｜KRONES Capping Technology

Modulcap GS screw capper for plastic caps

With the servo-driven screw capper for plastic caps,

there is also an optional variant with gripper in addition
to the one with chucks: This way, non-rotationally
symmetric caps such as caps with flaps or gripping
grooves can be processed as well.

Other than this special feature, the Modulcap GS

structure and function is similar to the one of the CS.
14 ｜KRONES Capping Technology

KRONES Crowners

The crowners are masters of capping glass and PET bottles with
exemplary precision.

Applications
− Crowns
− Twist-off caps
− Ring-pull caps

Service portfolio
Between 10,000 and 78,000 bottles per hour
15 ｜KRONES Capping Technology

KRONES Crowners

Method of operation Crowners: Crown transfer

Once the crown has been fed from the crown chute into Crown strip-off Crown feed unit
the transfer segment, a magnet is used for the further
guidance of the crown. A pushing notch is then used to
position the crown on the ejection plunger of the
capping head. The crowning head is lowered until the
crown in the crowning throat is placed on the bottle.
The bottle then holds it in place. Afterwards only the
crowning throat continues to be lowered. In the first
phase, only the force of the guiding springs has any
effect on the crown.

Magnet Ejection Magnet Magnet Pushing Ramp Crowning

plunger notch throat
The crown is The pushing Crown in The pushing The crown rests
removed from notch guides the transfer position notch feeds the against the
the ejection crown crown towards ejection plunger
plunger by downwards the ejection and is held in
magnets. below the strip plunger position by the
off wedge. magnet.
16 ｜KRONES Capping Technology

KRONES Crowners

Method of operation (continued) Crowners: Neck guide

In the second crowning phase, the ejection spring is pressed and Situation shortly
the bottle is subjected to an increased amount of pressure. The before the crown is
crowning procedure is completed once the crown has been applied to the bottle
introduced 7.7 mm into the capping throat. In doing so, the crown
is located 1 mm inside the cylindrical area of the crowning throat
and the required crown diameter of between 28.6 and 28.7 mm
has been exactly obtained. This completes the crowning Neck guiding
procedure. The crowning force once again drops. Neck guide starwheel
The delayed activity of the ejection spring guarantees high
crowning quality while applying a low level of pressure on the
bottle. The plunger is then blocked while the crowning throat is Supporting
plate
further lowered over the crown. At this time, the bottle height is
also compensated. A bottle which is too tall presses the bottle
plate downwards until the lowest area of the crowning head has
been reached. Controlled by the lifting cam, now the crowning
head moves upward again and the guiding spring presses the
ejection plunger back into the starting position.
17 ｜KRONES Capping Technology

KRONES Crowners

Design features Machine pitch 87 94 103 113 126 141 188 226 283
− All main parts made of stainless steel AISI 304
− Flushing of cap transfer unit and capping head
− Motorised height adjustment of the capper top part Pitch diameter (mm)
with bottle selection feature 360 13 12 11 10 9 8 6 5 4
540 18 15 12 9
Additional equipment 720 26 24 22 20 18 16 12 10
− UV lamp for cap disinfection
1080 39 36 33 30 27 24 18 15
− Dust blow-off with ionised air and suction
− Additional flushing equipment
18 ｜KRONES Capping Technology

KRONES Crowners
Your Advantages

Precision
Crowns enter the line with a defined alignment and are precisely
positioned on the transfer plate by a draw-in magnet.

Designed for practical applications

Bottle-neck centring ensures that even bottles with inaccurate
dimensions are reliable sealed.

Can be optimally cleaned

The capping heads can be cleaned perfectly with hot water or
foam.
19 ｜KRONES Capping Technology

KRONES Crowners
Conversion to Ring-Pull Caps

Parts to be converted
− Capping head
− Sorter of ring-pull caps for correct alignment
 Only required in case of a single tower for crowns and ring-
pull caps
 Mounted on platform
− Chute for positioning caps in infeed
 Mounted parallel to chute for crowns
 Can be adjusted to various bottle heights
20 ｜KRONES Capping Technology

KRONES Crowners
Conversion to Ring-Pull Caps

Conversion process
− Removal of
 Crown feed rail
 Capper heads
− Installation of
 Capper heads
 Chute for ring-pull caps
− In addition, the cap mass-flow conveyors must be emptied and
converted.

Time required
Between 60 and 90 minutes (depending on size of crown)

There are restrictions in the bottle height, as the elements required for applying the
crowns are of different lengths.
− Maximum height for a bottle with crown: 360 mm
− Maximum height for a bottle with ring-pull cap: 340 mm
21 ｜KRONES Capping Technology

KRONES Aluminium Roll-On Capper

Capping of glass bottles with aluminium roll-on caps is a standard

procedure in many areas of beverage bottling. The design of the
roll-on capper implements the latest knowledge from capping
technology and hygiene:

Applications
− Pilfer-proof and Stelcap caps
− Sizes: 28 mm and 31.5mm

Service portfolio
Between 10,000 and 60,000 bottles per hour
22 ｜KRONES Capping Technology

KRONES Aluminium Roll-On Capper

Method of operation
After they have been sorted according to their positions in the
sorter, the caps are fed to the capper via an open chute. A towing
shoe positions the caps, which are then directly picked up by the
bottle. If a cap is missing, a safety plunger prevents contact
between the rollers and the bottle neck finish. Depending on the
cap type, a “fixed” or a deep-drawing plunger is used for press-on
and shaping. The thread is rolled out via moveable arms, and if
necessary, the tamper-evident band is flanged. The lateral
pressure can be easily readjusted with adjusting screws.
23 ｜KRONES Capping Technology

KRONES Aluminium Roll-On Capper

Design features Machine pitch 94 103 113 126 141 188 226 283
− Structure completely designed in stainless steel
− Plastic guide bushes and lifting cylinders
− Maintenance-free cam roller Pitch diameter (mm)
− Capping heads with maintenance-free ceramic ball bearings 360 12 11 10 9 8 6 5 4
− Grease-free and therefore low-maintenance lifting elements 540 18 15 12
and capping heads 720 24 22 20 18 16 12
− Safety plungers prevent damage on the neck finish when
1080 36 30 24
cap is missing
− Entire capper can be flushed
− Adjustment of capping heads via set screws
− Side pressure can be adjusted quickly and easily
− Quick and easy changeover and adjustment of thread and
tuck-under roller arms
24 ｜KRONES Capping Technology

KRONES Aluminium Roll-On Cappers

Your Advantages

Flexibility
The thread and tuck-under roller arms can be quickly adjusted
to the plunger dimension.

Can be optimally cleaned

The capping heads can be cleaned perfectly with hot water or
foam.

Retains its value

The stainless steel design of the roll-on capper is highly
resistant to cleaning agents and disinfectants.
25 ｜KRONES Capping Technology

Everything from a single source

Training sessions at the KRONES Academy – trained personnel KIC KRONES cleaning agents make your machine shine
increases your line efficiency Only if the production environment is immaculate, can your
The versatile training offer ranges from operation, servicing and product be brilliant. KIC KRONES provides you with the optimum
maintenance to management training. We will gladly also cleaning agents and disinfectants for each individual production
establish your individual training programme. step.

KRONES Lifecycle Service – partner for performance Lubricants from KIC KRONES for every production step
Also after having purchased a new machine, KRONES will take Whether for gears, chains or central lubrication systems – our
care of your line; the LCS experts are always ready to consult you greases and oils are true all-round talents. They can reach every
and translate your goals and wishes into optimal LCS solutions. lubrication point, protect your line and ensure gentle treatment for
your products thanks to their food-grade quality.
Digitalisation Process Bottling and Intralogistics Lifecycle
technology packaging equipment Service

We do more.