تصنيع PDF

MINISTRY OF HIGHER
EDUATION&SCIENTIFIC RESEARCH
UNIVERSITY OF KIRKUK
COLLEGE OF ENGINEERING
MECHANICAL DEPARTMENT
THIRD STAGE&MORNING STUDY
MANUFACTURING PROCESSES
(DESIGN PRODUCT)
SUPERVISED BY: Mr. BILAL QASIM
BY: ABD-ULMOMEN KHALID MAHMOOD

INTRODUCTION: -
Design for Manufacturing (DFM) is the process of designing parts, components

or products for ease of manufacturing with an end goal of making a better
product at a lower cost. This is done by simplifying, optimizing and refining the
product design. The acronym DFMA (Design for Manufacturing and Assembly)
is sometimes used interchangeably with DFM.
seven principles are examined during a DFM. They are:
1. Process
2. Research
3. Design
4. Material
5. Environment
6. Testing
7. Manufacturing
Ideally, DFM needs to occur early in the design process, well before tooling has
begun. In addition, properly-executed DFM needs to include all the
stakeholder's engineers, designers, contract manufacturer, mold builder and
material supplier. The intent of this “cross-functional” DFM is to challenge the
design to look at the design at all levels: component, sub-system, system, and
holistic levels to ensure the design is optimized and does not have unnecessary
cost embedded in it.
The following chart offers an excellent visual representation of the effect of an

early DFM. As the design progresses through the product life cycle, changes
become more expensive, as well as more difficult to implement. Early DFM
allows design changes to be executed quickly, at the least expensive location.
Pulling stakeholders together early in the design process is easier if you're
developing a new product, but even if you're dealing with an established
product, challenging the original design is a necessary element of a thorough
DFM. Too often, mistakes in a design are repeated by replicating a previous
design. Question every aspect of your design.
1- PROCESS
The manufacturing process chosen must be the correct one for the part or
product. You wouldn't want to use highly-capitalized process like injection
molding which involves building of tools and dies to make a low-volume part
that could have been manufactured using a lower-capitalized method, such as
thermoforming. That would be equivalent to using a tank to squash an anthill a
classic case of overkill.
2-RESEARCH
There are two important things to research at this stage: firstly, demand. If your
product solves a problem, are a lot of people looking for a solution to that
problem? Can you see a gap that is desperate to be filled? Secondly, are there
products out there already that are similar to yours? If so, it doesn’t necessarily
mean your idea won’t be a success, but how will you improve on what is already
available.
3- DESIGN
Design is essential. The actual drawing of the part or product has to conform to
good manufacturing principles for the manufacturing process you’ve chosen.
In the case of plastic injection molding, for example, the following principles
would apply:
 Constant wall thickness, which allows for consistent and quick part
cooling
 Appropriate draft (1 - 2 degree is usually acceptable)
 Texture - need 1 degree for every 0.001” of texture depth on texture side
walls
 Ribs = 60 percent of nominal wall, as a rule of thumb
 Simple transitions from thick to thin features
 Wall thickness not too small - this increases injection pressure
 No undercuts or features that require side action - all features “in line of
pull/mold opening”
 Spec the loosest tolerances that allow a good product - and consult the
trade organization for your manufacturing process on what is reasonable
for that process
Be sure to discuss the design with your contract manufacturer, who can ensure
that your design conforms to good manufacturing principles for the selected
process.
4-MATERIAL
It's important to select the correct material for your part/product.
Some material properties to consider during DFM include:
 Mechanical properties - How strong does the material need to be?

 Optical properties - Does the material to be reflective or transparent?
 Thermal properties - How heat resistant does it need to be?
 Color - What color does the part need to be?
 Electrical properties - Does the material need to act as a dielectric (act as
an insulator rather than a conductor)?
 Flammability - How flame/burn resistant does the material need to be?
Again, be sure to discuss the material with your contract manufacturer, who
might have access to existing materials in their portfolio which would allow you
to secure lower material pricing.
5-ENVIRONMENT
Your part/product must be designed to withstand the environment it will be

subjected to. All the form in the world won’t matter if the part can’t function
properly under its normal operating conditions.
6-TESTING
All products must comply with safety and quality standards. Sometimes these
are industry standards, others are third-party standards and some are internal,
company-specific standards.
7-MANUFACTURING
If you made it through prototype testing without revealing any problems that
need to be worked on, it’s time to manufacture your product. There may be
some further decisions to make here, such as materials, batch numbers, and the
manufacturer itself. Think about what keeps costs low while maintaining the
quality you want, so that you can maximize profits.
Now you have successfully taken your product from concept to a polished final
product, it’s time to turn your attention to marketing, and the practical side of
getting it into the hands of customers. The more you sell, the more you can
afford to put into manufacturing larger batches, meaning a larger profit next
time around!
FACTORS THAT AFFECT DFM
The goal of DFM is to reduce manufacturing costs without reducing

performance. In addition to the principles of DFM, here are five factors that can
affect design for manufacturing and design for assembly:
1 | Minimize Part Count
Reducing the number of parts in a product is the quickest way to reduce cost
because you are reducing the amount of material required, the amount of
engineering, production, labor, all the way down to shipping costs.
2 | Standardize Parts and Materials
Personalization and customization are expensive and time-consuming. Using

quality standardized parts can shorten time to production as such parts are
typically available and you can be more certain of their consistency.
Material is based on the planned use of the product and its function. Consider:
 How should it feel? Hard? Soft?

 Does it need to withstand pressure?
 Will your part or product need to conduct heat, electricity?
3 | Create Modular Assemblies
Using non-customized modules/modular assemblies in your design allows you

to modify the product without losing its overall functionality. A simple example
is a basic automobile that allows you to add in extras by putting in a modular
upgrade.
4 | Design for Efficient Joining
Can the parts interlock or clip together? Look for ways to join parts without the
use of screws, fasteners or adhesives. If you must use fasteners, here are a few
tips:
 Keep the number, size and variation of fasteners to a minimum

 Use standard fasteners as much as possible.
 Use self-tapping and chamfered screws for better placement.
 Stay away from screws that are too long or too short, separate washers,
tapped holes, round heads and flatheads.
5 | Minimize Reorientation of Parts During Assembly & Machining
Parts should be designed so that a minimum of manual interaction is necessary

during production and assembly.
10 OUTCOMES OF AN EFFECTIVE DFM
The book Computer-Aided Manufacturing offers 10 generally accepted Design

for Manufacturing principles that were developed to help designers decrease the
cost of and complexity of manufacturing a product. The results of a successful
DFM are quantifiable in a host of ways.
1. Minimize the number of product parts. Limiting the number of parts in

your product is an easy way to lower the cost of a product. Why? Because
it automatically reduces the amount of material and assembly labor
required. Reducing the number of parts also means less engineering,
production, labor and shipping costs.
2. Use standardized parts wherever possible. Customization is not only
expensive, it’s time consuming. Standardized parts are already made to
meet the same quality metrics, every time. They are already tooled. So
you save costs and you won’t have to wonder whether they’ll pass
inspection.
3. Create a modular design. Using modules can simplify any future product
redesign, and also allows for use of standard components and the re-use of
modules in other projects.
4. Design multi-functional parts. This seems rather obvious, but it’s a simple
way to reduce the total number of parts: design parts with more than one
function.
5. Design multi-use products. Building on the point above,

different products can share parts that have been designed for multi-use.
Can your product use standardized parts that can are used in multiple
products?
6. Design for ease of fabrication. Choose the ideal combination between the
material and manufacturing process that will minimize production costs.
Ridiculously tight tolerances are a no-no. [More about that below.] Avoid
expensive and labor extensive final operations as painting, polishing and
finish machining.
7. Design your product to join without using screws, fasteners or

adhesives. Is it possible for your product to interlock or clip together?
Screws add only about 5% to the material cost, but 75% to the assembly
labor. Remember: if fasteners are required, try to keep the size, number
and type to a minimum and use standard fasteners whenever possible.
8. Design your part to minimize handling, especially during production and

assembly. Handling includes positioning, orienting and fastening the part
into place. For orientation purposes, use symmetrical parts wherever
possible.
9. Minimize assembly direction. If possible, your parts should assemble

from one direction. Ideally, parts should be added from above, parallel to
the gravitational direction (AKA downward.) This way assembly is
facilitated by gravity rather than fought by it.
10.Design your part to maximize compliance. Rely on built-in design

features like tapers or chamfers, or moderate radius sizes to guide
insertion of equipment and to protect the part from damage.

تصنيع PDF

Uploaded by

Copyright:

Available Formats

تصنيع PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

تصنيع PDF

Uploaded by

Copyright:

Available Formats

MINISTRY OF HIGHER

SUPERVISED BY: Mr. BILAL QASIM

BY: ABD-ULMOMEN KHALID MAHMOOD

Design for Manufacturing (DFM) is the process of designing parts, components

seven principles are examined during a DFM. They are:

The following chart offers an excellent visual representation of the effect of an

It's important to select the correct material for your part/product.

Some material properties to consider during DFM include:

 Mechanical properties - How strong does the material need to be?

Your part/product must be designed to withstand the environment it will be

The goal of DFM is to reduce manufacturing costs without reducing

1 | Minimize Part Count

2 | Standardize Parts and Materials

Personalization and customization are expensive and time-consuming. Using

 How should it feel? Hard? Soft?

3 | Create Modular Assemblies

Using non-customized modules/modular assemblies in your design allows you

 Keep the number, size and variation of fasteners to a minimum

5 | Minimize Reorientation of Parts During Assembly & Machining

Parts should be designed so that a minimum of manual interaction is necessary

10 OUTCOMES OF AN EFFECTIVE DFM

The book Computer-Aided Manufacturing offers 10 generally accepted Design

1. Minimize the number of product parts. Limiting the number of parts in

5. Design multi-use products. Building on the point above,

7. Design your product to join without using screws, fasteners or

8. Design your part to minimize handling, especially during production and

9. Minimize assembly direction. If possible, your parts should assemble

10.Design your part to maximize compliance. Rely on built-in design

You might also like