PCL6 V4 PrinterDriver V712 UG EN PDF

Windows
UFR II/UFRII LT/LIPSLX/CARPS2/PCL6 V4 Printer Driver
User's Guide
USRMA-3204-03 2019-07 en Copyright CANON INC. 2019

Contents
Introduction ....................................................................................................................................................... 2
How to Use the Manual ............................................................................................................................................. 3
Notations Used in the Manual ................................................................................................................................ 4
Disclaimers ............................................................................................................................................................... 5
Copyright .................................................................................................................................................................. 6
Trademarks .............................................................................................................................................................. 7
About This Driver ........................................................................................................................................... 9
Before Use ......................................................................................................................................................... 12
Installing the Driver .................................................................................................................................. 14

Pre-installation Check ............................................................................................................................................. 15
System Requirements ......................................................................................................................................... 16
Notes and Warnings Regarding Installation ........................................................................................................... 17
About the Readme File ........................................................................................................................................ 18
Installing by Discovering Devices on a Network ....................................................................................................... 19
Installing by Specifying a Port or IP Address ............................................................................................................. 24
Installing by USB Connection ................................................................................................................................... 30
Installing by Specifying an inf File ............................................................................................................................ 33
Installing Using Windows Update ............................................................................................................................ 35
Updating/Uninstalling the Driver ............................................................................................................................. 37
Updating the Driver ............................................................................................................................................ 38
Uninstalling the Driver ........................................................................................................................................ 40
Changing Settings to Match the Usage Environment .................................................. 44

Using a Shared Printer ............................................................................................................................................ 45
Installing as a Print Server ................................................................................................................................... 46
Setting up Clients of a Shared Printer .................................................................................................................... 48
Changing the Port ................................................................................................................................................... 51
Making the Device Functions Usable ........................................................................................................................ 55
Printing ................................................................................................................................................................ 59
Printing from a Desktop App ................................................................................................................................... 60
Printing from a Store App ........................................................................................................................................ 63
Scaling .................................................................................................................................................................... 69
Attaching a Watermark ........................................................................................................................................... 70
Printing a Large Poster over Multiple Pages ............................................................................................................. 71
Overlapping Print Data on a Fixed Form ................................................................................................................... 75
Attaching a PIN to Print Data .................................................................................................................................. 77
I
Encrypting Print Data .............................................................................................................................................. 78
Putting Print Jobs on Hold ....................................................................................................................................... 80
Storing Print Data ................................................................................................................................................... 81
Prioritizing a Print Job over Other Print Jobs ............................................................................................................. 82
Suspend Currently Printing Jobs to Prioritize a Print Job ........................................................................................... 83
Changing the Default Settings ................................................................................................................................. 84
Creating a Booklet ...................................................................................................................................... 86

Booklet Printing ...................................................................................................................................................... 87
Creating a Booklet in Sets ........................................................................................................................................ 88
Correcting Displacement During Booklet Printing .................................................................................................... 89
Saddle Stitched Booklet Printing .............................................................................................................................. 90
Saddle Press Processing When Creating Saddle Stitched Booklets ............................................................................. 91
Trimming Pages When Creating Saddle Stitched Booklets ......................................................................................... 92
Perfect Binding ....................................................................................................................................................... 93
Printing Page Numbers in the Same Position on the Front and Back of Each Page ...................................................... 94
Using Various Types of Paper ............................................................................................................ 97

Registering Custom Paper Sizes ............................................................................................................................... 98
Inserting Sheets Between Transparencies ................................................................................................................ 99
Inserting Sheets .................................................................................................................................................... 100
Inserting Tab Paper ............................................................................................................................................... 101
Printing on Tab Paper ............................................................................................................................................ 102
Editing Favorite Settings ..................................................................................................................... 104

Registering Favorite Settings ................................................................................................................................ 105
Editing the Favorite Settings List ........................................................................................................................... 106
Coordinating with the Device Functions ............................................................................... 109

Setting the Authentication Function ...................................................................................................................... 110
Setting the User Name .......................................................................................................................................... 112
Confirming Set User Information Prior to Printing ................................................................................................. 114
Settings List ................................................................................................................................................... 117

Common Settings for All Sheets ............................................................................................................................. 118
[Main] Sheet ......................................................................................................................................................... 120
[Layout] Sheet ....................................................................................................................................................... 123
[Paper Feed] Sheet ................................................................................................................................................ 127
[Finishing] Sheet ................................................................................................................................................... 129
[Quality] Sheet ...................................................................................................................................................... 131
[Covers] Sheet ....................................................................................................................................................... 134
[Support/Device] Sheet .......................................................................................................................................... 135
[Device Settings]/[Administrator Settings] Sheet .................................................................................................... 137
II
Troubleshooting ......................................................................................................................................... 140
Cannot discover a device on a network .................................................................................................................. 141
Icon of the device is not displayed after installation ............................................................................................... 143
The Windows standard print settings screen is displayed ....................................................................................... 144
Print settings return to their defaults after updating the driver ............................................................................. 148
III
Introduction
Introduction
Introduction .......................................................................................................................................................... 2
How to Use the Manual ......................................................................................................................................... 3
Notations Used in the Manual .......................................................................................................................... 4
Disclaimers ............................................................................................................................................................. 5
Copyright ............................................................................................................................................................... 6
Trademarks ............................................................................................................................................................ 7
1
Introduction
Introduction
How to Use the Manual(P. 3)

Disclaimers(P. 5)
Copyright(P. 6)
Trademarks(P. 7)
2
Introduction
How to Use the Manual
This explains things that you need to know in order to use this manual.
Notations Used in the Manual(P. 4)
3
Introduction
Notations Used in the Manual
This explains symbols and settings used in this manual.
Symbols Used in This Manual

In this manual, explanations of items and operations that must be followed while using the driver are set forth
the symbols that indicate the following.
IMPORTANT
● Indicates operational requirements and restrictions. Be sure to read these items carefully to operate the
product correctly, and avoid damage to the product.
NOTE
● Indicates a clarification of an operation, or contains additional explanations for a procedure. Reading these
notes is highly recommended.
About Settings
In this manual, setting names displayed on the computer screen are represented as shown in the following
examples.
Example:
[Print]
[OK]
4
Introduction
Disclaimers
The information in this document is subject to change without notice.
CANON INC. MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR
IMPLIED, EXCEPT AS PROVIDED HEREIN, INCLUDING WITHOUT LIMITATION, THEREOF, WARRANTIES AS TO
MARKETABILITY, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OF USE OR NON-INFRINGEMENT.
CANON INC. SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.
5
Introduction
Copyright
Copyright CANON INC. 2019
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise, without the prior written permission of Canon Inc.
6
Introduction
Trademarks
Microsoft, Windows, Windows Server, Internet Explorer, and Microsoft Edge are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
macOS and Safari are trademarks of Apple Inc.
Other product and company names herein may be the trademarks of their respective owners.
7
About This Driver
About This Driver

About This Driver ............................................................................................................................................... 9
8
About This Driver
About This Driver
This driver enables you to display the print settings screen of drivers that support Windows Store apps and
desktop apps, and use the print functions of Canon devices.
In this manual, Windows Store apps, Windows apps, and UWP (Universal Windows Platform) apps are referred
to as store apps.
Printing from a Desktop App

The following print settings screen is displayed when you print from desktop apps.
Printing from a Store App

The following print settings screen is displayed when you print from store apps.
The functions required to print from store apps are automatically installed from the Windows Store after the
driver is installed.
9
About This Driver
Related Topics
Printing from a Desktop App(P. 60)
Printing from a Store App(P. 63)
10
Before Use
Before Use
Before Use ............................................................................................................................................................ 12
11
Before Use
Before Use
● The newest driver software is posted on the Canon web site. Please verify the operating environment etc.
and download the appropriate software as required.
Canon Global Site: https://global.canon/
● The functions that you can use may vary according to the following conditions.
- The device you are using and its settings
- The firmware version of the device
- The option structure of the device
- The driver you are using
- The driver version
- The computer environment you are using
● The screen content, procedures, etc. displayed and described in the manual may differ from those actually
displayed.
● In this manual, examples using Windows 10 are explained.
12
Installing the Driver

Installing the Driver ....................................................................................................................................... 14
Pre-installation Check ......................................................................................................................................... 15
System Requirements ..................................................................................................................................... 16
Notes and Warnings Regarding Installation ................................................................................................... 17
About the Readme File ................................................................................................................................... 18
Installing by Discovering Devices on a Network ............................................................................................... 19
Installing by Specifying a Port or IP Address ..................................................................................................... 24
Installing by USB Connection ............................................................................................................................. 30
Installing by Specifying an inf File ..................................................................................................................... 33
Installing Using Windows Update ...................................................................................................................... 35
Updating/Uninstalling the Driver ...................................................................................................................... 37
Updating the Driver ........................................................................................................................................ 38
Uninstalling the Driver .................................................................................................................................... 40
13
Select the installation method suitable to the connection method and environment of the device you are using.
Pre-installation Check(P. 15)
Installing by Discovering Devices on a Network(P. 19)
Installing by Specifying a Port or IP Address(P. 24)
Installing by USB Connection(P. 30)
Installing by Specifying an inf File(P. 33)
Installing Using Windows Update(P. 35)
Updating/Uninstalling the Driver(P. 37)
14
Pre-installation Check
This explains what to confirm beforehand in order to install the driver correctly.
System Requirements(P. 16)
Notes and Warnings Regarding Installation(P. 17)
About the Readme File(P. 18)
15
System Requirements
This driver can be used with the following system environments.
Operating Systems
● Windows 10 *
● Windows 8.1
● Windows Server 2019
● Windows Server 2016
● Windows Server 2012 R2
* Some displays and functions may not operate correctly on tablet terminals and smart phones.
Hardware
● Any computer that is guaranteed to run the above operating systems
Combinations of Driver and Operating System Display Languages

Depending on the combination of supported driver languages and the display language of the operating
system, correct operation may not be guaranteed. It is recommended that you install with the language
selected by default when the installer starts.
Supported Driver Languages

English / Arabic / Basque / Catalan / Chinese (Simplified) / Chinese (Traditional) / Czech / Danish / Dutch /
Finnish / French / German / Hungarian / Italian / Japanese / Korean / Malay / Norwegian / Polish / Portuguese /
Russian / Slovak / Spanish / Swedish / Thai / Turkish / Vietnamese
Scope of Guaranteed Operation
Language of operating Language of operating system

system included in not included in supported
supported driver driver languages
languages
Installed with language matching the operating Guaranteed --

system
Installed with language not matching the Guaranteed*1 Not guaranteed*2

operating system
Changed to language not matching the operating Guaranteed*1 Not guaranteed*2

system after installation
*1 The layout may be broken or the driver may not be displayed correctly.
*2 Operation is only guaranteed when installed with English. However, the layout may be broken or the driver may not be
displayed correctly.
16
Notes and Warnings Regarding Installation
Take care of the following items when installing.

● If a screen requiring you to allow changes to the computer is displayed, allow the changes.
● If a Windows Security screen indicating that the publisher of the driver cannot by verified is displayed, allow
installation.
● If the icon of the device is not displayed in [Devices and Printers] when installation is complete, there could
be a problem with the screen or installation state. Refer to Troubleshooting to have the icon of the device
displayed.
Related Topics
Icon of the device is not displayed after installation(P. 143)
17
About the Readme File
Precautions when installing drivers or using drivers are written in the Readme file.
The Readme file is stored under the following name in the folder of the downloaded driver.
Readme_en.html
Also, if you are installing using the installer, you can refer to the screen for checking the CANON SOFTWARE
LICENSE AGREEMENT.
18
Installing by Discovering Devices on a Network
You can automatically search for a device in a network environment and install the driver.
You can search for devices on TCP/IP networks and network environments that use WSD.
NOTE
● For network environments other than the above, refer to the procedure for installing by specifying a port or
IP address.
● If you do not know the network environment you are using, check with your network administrator.
Prerequisites
● System Requirements(P. 16)
● Enabling [Multicast Discovery Settings] at the device
For network environments that use WSD, enable [Use WSD].
● Setting the page description language selection (plug and play) function of the device
Set [PDL Selection (Plug and Play)] at the device to match the driver you are using. For details about the
setting method, refer to the manual of the device.
- For "UFR II/UFRII LT/LIPSLX/CARPS2 V4 Printer Driver": [*** (V4)] (or [*** (XPS)])
*** represents the page description language corresponding to the device.
- For "PCL6 V4 Printer Driver": [PCL6 (V4)] (or [PCL6])
● The device is one that is on the same subnet as the computer you are using (for TCP/IP network
environments)
● Notes and Warnings Regarding Installation(P. 17)
● When starting the computer, logon as a member of Administrators.
● [Desktop] screen display (when using Windows 8.1/Server 2012 R2)
Procedures
1 Double-click [Setup.exe].
2 If you want to change the language displayed by the installer, select [Language] →
click [Next].
The driver will be installed according to the selected language.
3 Read the CANON SOFTWARE LICENSE AGREEMENT → click [Yes].

In the screen for checking the CANON SOFTWARE LICENSE AGREEMENT, if you click [Display Readme File], you
can refer to the content of the Readme file.
4 Select [Standard] → click [Next].
19
[Wake any printers that are in sleep mode and search]: Select this when you want to detect devices on the
network that are in sleep mode.
5 If the following screen is displayed, select [Add new printers] → click [Next].
[Add new printers and update existing printer drivers]: Select this when you want to update already installed
drivers at the same time that you add a new driver.
20
6 If the following message is displayed, confirm the message and click [Yes] or [No].
[Yes]: Communication using the TCP/IP protocol and WSD is enabled. This is normally recommended.
[No]: Communication is limited to the TCP/IP protocol only. In this case, device information may not be able to
be retrieved correctly.
7 Select the device to install from [Printer List].

If the device is not displayed in [Printer List], click [Search Again].
NOTE
21
● If you cannot discover a device, there could be a problem with the operating system or device settings. Refer
to the subsequent troubleshooting to enable the device to be displayed in the discovery results.
Cannot discover a device on a network(P. 141)
8 If you want to change the name of the device, or set it as the default device, select
[Configure printer information] → click [Next].
If you do not want to change the name of the device or set it as the default device, click [Next] and proceed to
step 10.(P. 23)
9 Change [Printer Name] if necessary → click [Next].

[Set as default]: Select this to set the device as the device that is normally used.
[Use as shared printer]: Select this if you want to share the device.
[Port]: Select the port you want to use if you can use multiple ports.
22
10 Check [List of Printers for Installation] → click [Start].

Proceed with the installation according to the instructions on the screen.
11 Check the installation complete message → click [Exit].

You can also print a test page if required.
Related Topics
Installing as a Print Server(P. 46)
23
Installing by Specifying a Port or IP Address
You can manually specify the port or IP address to use for network connected or locally connected devices and
install the driver. Install according to this procedure when you cannot automatically discover a device on the
network or when unique settings are required.
As well as using an existing port, you can add a port.
Prerequisites
● Confirm the port to be specified
Specify a WSD port, standard TCP/IP port, network printer port, or local port. You can specify an already
registered port. You can select a temporary port ([LPT1] etc.) and set it after installation is complete.
● Confirm the host name, name, or IP address of the device (if adding a WSD port or a standard TCP/IP port).
If you are installing by adding a WSD port or a standard TCP/IP port, you need to enter the host name, name,
or IP address of the device. For the host name or name of the device, use the name by which the device is
known on the network. If you do not know the name or value to be specified, check with your network
administrator.
● Confirm the shared printer (if adding a network printer port)
The shared printer selected when adding the port must match the device selected via the installer. Also,
confirm that the version of the driver installed in the shared printer and the version of the installer match.
Make sure to log on to the computer in which the specified shared printer is installed beforehand.
Procedures
click [Next].
4 Select [Custom] → click [Next].
24
5 If the following screen is displayed, select [Add new printers] → click [Next].
[Add new printers and update existing printer drivers]: Select this when you want to update already installed
drivers at the same time that you add a new driver.
[Update existing printer drivers]: Select this if you want to update drivers only. For details, refer to the
procedure for updating drivers.
25
6 Select the device to install from [Printer List] → click [Next].

[Number of Printers]: Enter the number of printers to be installed for the selected device. By specifying
multiple printers, multiple devices can be registered at the same time.
NOTE
● When multiple printers are assigned the same port for a single device, multiple print queues are registered
for the selected device. Different default settings can be specified for each print queue to distinguish
between them when printing. However, you can assign only one port to one device when a WSD port or
network printer port is specified.
26
7 Set the port.

If you have entered multiple printers for one device in step 6.(P. 26) , the port setting for the first printer is
used as the default setting for the second and subsequent printers.
27
When adding a WSD port

(1) Click [Add Port] → select [WSD Port] from [Port to Add] → click [OK].
(2) Enter the IP address or host name → click [OK].
When adding a standard TCP/IP port
(1) Click [Add Port] → select [Standard TCP/IP Port] from [Port to Add] → click [OK].
(2) Enter the device name or IP address according to the instructions of the wizard.
[Port Name] is automatically entered. Change the port name if required.
If the [Additional port information required] screen is displayed, click the subsequent "Open details" and
perform the necessary operations.
Perform one of the following.
- Return to the previous screen in the wizard → re-enter the information for [Printer Name or IP Address] →
click [Next].
- Select [Device Type] > [Standard] > [Canon Network Printing Device with P9100] → click [Next].
Depending on the device you are using, the name you select in [Device Type] > [Standard] may differ from
[Canon Network Printing Device with P9100].
(3) Click [Finish].
When adding a network printer port
(1) Click [Add Port] → select [Network] from [Port to Add] → click [OK].
(2) Select the network printer you are using → click [OK].
NOTE
● If a network printer corresponding to the device is not displayed in the list, the operating system or device
settings may be incorrect. Refer to the subsequent troubleshooting to enable the device to be displayed in
the printer list.
When adding a local port
(1) Click [Add Port] → select [Local Port] from [Port to Add] → click [OK].
(2) Enter the port name → click [OK].
28
When using an existing port

Select a port from [Port].
8 Change [Printer Name] if necessary → click [Next].

[Set as default]: Select this to set the device as the device that is normally used.
[Use as shared printer]: Select this if you want to share the device.
If you added or selected a network printer port, you cannot set [Printer Name] and [Use as shared printer].
If you have selected multiple devices or you have entered multiple printers for one device in step 6.(P. 26) ,
repeat steps 7.(P. 27) and 8.(P. 29)


Related Topics
Changing the Port(P. 51)
Updating the Driver(P. 38)
29
Installing by USB Connection
You can connect the device and computer with a USB cable and install the driver.
Prerequisites
● Installation of the optional USB interface board (if required with the device you are using)
● Page description language selection (plug & play) function setting of the device (if required with the device
you are using)
Set [PDL Selection (Plug and Play)] at the device to match the driver you are using. For details about the
setting method, refer to the manual of the device.
Procedures
1 Turn off the device.
click [Next].
5 Select [USB Connection] → click [Next].
30
6 When the following screen appears, turn on the device → connect the device and
computer with a USB cable.
[Skip]: If correctly connected by USB, in this screen you can finish the installation without waiting for automatic
completion.
31

If installation fails in the above screen, click the subsequent "Open details" and perform the necessary
operations.
Reinstall the driver after performing the following procedure.
(1) Turn on the device → connect the device and computer with a USB cable.
(2) Display [Device Manager].
In Windows 10/Server 2016/Server 2019
Right-click [ ] → click [Device Manager].
In Windows 8.1/Server 2012 R2

Display [Control Panel] > [Hardware and Sound] > [Device Manager].
(3) Right-click the device name of the target device from [Other devices] → click [Uninstall device] or [Uninstall].
(4) Confirm the device name.
Canon + <model name being used>

32
Installing by Specifying an inf File
This explains the procedure for installing a driver by specifying an inf file with the add printer function of
Windows.
If you install according to this procedure, you will have to use the Windows standard print settings screen when
printing from a desktop app because the print settings screen of the driver will not be displayed.
The explanation will be given with respect to installation with a standard TCP/IP port.
Prerequisites
● Confirm the IP address of the device.
● When starting the computer, log on as a member of Administrators.
Procedures
1 Start the Windows add printer wizard.

If starting from [Settings] (Windows 10/Server 2016/Server 2019 only)
(1) Click [Devices] → click [Add a printer or scanner] from [Printers & scanners].
(2) Click [The printer that I want isn’t listed].
If starting from [Control Panel]
(1) Display [Devices and Printers] → click [Add a printer].
(2) In the screen for selecting a device, click [The printer that I want isn't listed].
2 Select local printer addition and proceed to the next screen.
3 Select [Create a new port] → select [Standard TCP/IP Port] from [Type of port] → click
[Next].
4 Enter the IP address of the device in [Hostname or IP address] → proceed according to

the instructions on the screen.
If the device cannot be found, it may be recognized as an unknown device. If so, click the subsequent "Open
details."
(1) Display [Device Manager] in Windows.
In Windows 10/Server 2016/Server 2019: Right-click [ ] → click [Device Manager].
In Windows 8.1/Server 2012 R2: Click [Control Panel] > [Device Manager].
(2) Select [Other devices] > [Unknown device] → click the [Action] menu > [Update driver] or [Update Driver
Software].
(3) In the driver update wizard, click [Browse my computer for driver software] > [Let me pick from a list of
available drivers on my computer].
33
(4) Select [Printers] from [Common hardware types] → click [Next].
5 In the [Add Printer] screen, click [Have Disk].
6 Click [Browse] → select one of the inf files in the downloaded driver folder.
Operations will be unaffected regardless of which inf file you select.
7 Select the device to use from [Printers] → click [Next].
8 Install the driver according to the instructions on the screen → click [Finish].
Related Topics
The Windows standard print settings screen is displayed(P. 144)
34
Installing Using Windows Update
This explains the procedure for installing a driver by using Windows Update in the add printer function of
Windows.
Use this procedure to install the driver when it cannot be installed using the driver installer.
If you install according to this procedure, you will have to use the Windows standard print settings screen when
printing from a desktop app because the print settings screen of the driver will not be displayed.
The explanation will be given with respect to installation with a standard TCP/IP port.
Prerequisites
● You are using Windows 10 Version 1703 or later
● Confirm the IP address of the device.
Procedures
1 Start the Windows add printer wizard.

(1) Display [Settings] > [Devices] > [Printers & scanners].
(2) Click [Add a printer or scanner] → click [The printer that I want isn’t listed] if it is displayed.
2 Select local printer addition and proceed to the next screen.
3 Select [Create a new port] → select [Standard TCP/IP Port] from [Type of port] → click
[Next].
4 Enter the IP address of the device in [Hostname or IP address] → proceed according to

the instructions on the screen.
If the device cannot be found, it may be recognized as an unknown device. If so, click the subsequent "Open
details."
(1) Right-click [ ] of Windows → select [Device Manager] from the menu.
(2) Select [Other devices] > [Unknown device] → select the [Action] menu > [Update driver].
(3) In the driver update wizard, click [Browse my computer for driver software] > [Let me pick from a list of
available drivers on my computer].
(4) Select [Printers] from [Common hardware types] → click [Next].
5 In the [Add Printer] screen, click [Windows Update].
6 Select the device to use from the printers with "V4" in the [Printers] list → click [Next].
35
7 Install the driver according to the instructions on the screen → click [Finish].
Related Topics
System Requirements(P. 16)
36
Updating/Uninstalling the Driver
The procedures for updating the driver and uninstalling the driver are described below.
Uninstalling the Driver(P. 40)
37
Updating the Driver
You can update installed drivers to their newer versions.
It is recommended that you download the latest drivers corresponding to new functions and/or operating
systems, and update them.
You can update already installed drivers at the same time as installing a driver for a new device, but here the
procedure for updating installed drivers only is explained.
Prerequisites
● Acquire the installer
You can download the update installer from the Canon web site (https://global.canon/).
● Connect the device by USB cable and turn the power on (when updating a driver installed with a USB
connection).
IMPORTANT
● The driver can also be updated without using an installer by using Windows Update in the add printer
function of Windows.
However, if the driver is updated using Windows Update, the Windows standard print settings screen may be
displayed. In this case, refer to the subsequent troubleshooting to enable the print settings screen of the
driver to be displayed.
Procedures
1 Start the installer → proceed according to the instructions on the screen.
2 Select [Custom] for [Printer Setup] → click [Next].
3 Select [Update existing printer drivers] → click [Next].
38

Restart your computer when a message is displayed prompting you to do so.
When updating a driver on a print server, update the drivers on clients as well, referring to the procedure for
setting computers as shared printer clients.
Related Topics
Setting up Clients of a Shared Printer(P. 48)
Making the Device Functions Usable(P. 55)
39
Uninstalling the Driver
This explains the procedure for uninstalling a driver that is no longer needed.
The uninstallation method differs depending on whether the installer, or the add printer function of Windows
was used (by specifying an inf file or using Windows Update) when the driver was installed.
For drivers that were installed by an installer(P. 40)
For drivers that were installed with the add printer function of Windows(P. 41)
Prerequisites
Procedures
For drivers that were installed by an installer
1 Start the uninstaller of the driver.
When using Windows functions

(1) Display [Settings] > [Apps] or [System] > [Apps & features].
(2) Select the driver to be uninstalled in [V4 Printer Driver Uninstaller] → click [Uninstall].
In operating systems other than the above
(1) Display [Control Panel] > [Programs] > [Uninstall a program].
(2) Select the driver to be uninstalled in [V4 Printer Driver Uninstaller] → click [Uninstall/Change].
When using the Windows uninstall function, the uninstaller is displayed in the language you selected in the
installer.
When using the uninstall file provided with the driver

Double-click one of the following files.
When using a file in an installed driver folder
Use [UNINSTAL.exe] corresponding to the driver within the following folder.
<install folder>\Canon\PrnUninstall
When using a file in a downloaded driver folder
Installer\UNINSTAL.exe
2 Select the name of the device you want to uninstall → click [Delete].
[Cleanup]: Click this to simultaneously delete all files and registry information relating to all of the drivers
displayed in the list, not just the selected driver. Click [Delete] to perform a normal uninstallation of the driver.
40
3 In the screen for confirming whether to delete the printer, click [Yes].
A confirmation message asking whether you want to delete the package as well may be displayed.
4 In the [Delete Printer] screen, click [Exit].
NOTE
● When connected to a device by USB, the icon of the device cannot be deleted by the uninstaller. To delete it,
perform the procedure for uninstalling drivers that were installed with the add printer function of Windows.
For drivers that were installed with the add printer function of Windows
1 Display [Devices and Printers] from the [Control Panel] of Windows.
2 Right-click the icon of the device you are going to remove → select [Remove device].
If you are using a touch panel, press and hold the icon of the device you want to delete → tap [Remove device]
in the pop-up menu.
3 In the [Remove device] screen, click [Yes].
41
4 Select the icon of any device → click [Print server properties] from the menu.
5 Display the [Drivers] sheet in the [Print Server Properties] screen.
6 Click [Change Driver Settings] → select the driver to be removed from [Installed printer
drivers] → click [Remove].
7 Select [Remove driver and driver package] → click [OK].
8 Confirm the driver in the confirmation screen → click [Yes].
9 If the [Remove Driver Package] screen is displayed, click [Delete] after verifying the
package information → click [OK].
A message indicating that the package cannot be deleted may be displayed. In this case, only the driver is
deleted.
42
Changing Settings to Match the Usage Environment
Changing Settings to Match the

Usage Environment
Changing Settings to Match the Usage Environment ................................................................ 44
Using a Shared Printer ........................................................................................................................................ 45
Installing as a Print Server .............................................................................................................................. 46
Setting up Clients of a Shared Printer ............................................................................................................. 48
Changing the Port ............................................................................................................................................... 51
Making the Device Functions Usable ................................................................................................................. 55
43
This explains shared printer settings, switching ports, and manually setting the option installation status of a
device.
Using a Shared Printer(P. 45)
44
Using a Shared Printer
This explains the setting procedure for sharing a device with computers on the same network.
45
Installing as a Print Server
This explains how to configure the share settings of and install the driver in order to use a computer connected
to the device as a print server.
Prerequisites
Procedures
2 Select [Standard] or [Custom] for [Printer Setup] → click [Next].

If you have a network connection that does not use the TCP/IP protocol, select [Custom].
3 If the [Select Process] screen is displayed, select [Add new printers] → click [Next].
4 Select the device to install from [Printer List] → click [Next].

If you select [Standard] and configure shared settings, select [Configure printer information], then click [Next].
5 Select [Use as shared printer] → change [Shared Name] if necessary → click [Next].
If you select [Custom] and configure shared settings, set the port in [Port], then click [Next].
46
6 Follow the instructions on the screen → click [Exit].
Related Topics
47
Setting up Clients of a Shared Printer
This explains the procedure for enabling printing from a client computer (hereafter referred to an "a client")
using a print server being shared on the same network.
Prerequisites
● Configure the share settings of the print server driver
NOTE
● If you are configuring the settings of a client in a workgroup environment, the user name and password for
logging onto the client must match the user name and password registered in the server.
Procedures
1 Display [Network] in Windows Explorer.
2 Double-click the computer (print server) you have set for print sharing.
3 Double-click the icon of the device for installation.
4 Check how the print settings screen is displayed at the client.

You can display the print settings screen by the following procedure.
(1) Display [Devices and Printers] in Windows.
(2) Right-click the icon of the device you are going to set → select [Printing preferences].
If the following screen is displayed, perform the following procedure.
48
If the following screen is displayed, the operation is finished.
49
Use the same version driver as the print server to install.
6 Select [Custom] for [Printer Setup] → click [Next].
7 In the [Select Process] screen, select [Update existing printer drivers] → click [Next].
9 Click [Exit].
10 Restart the computer after installation is complete.
Related Topics
50
Changing the Port
This explains the procedure for changing the port used by a device connected to a network.
If you temporarily set a port of the device when installing the driver, change it to a correct port by following this
procedure.
Here, the method for creating a Raw or LPR port using "Standard TCP/IP Port" is explained.
Prerequisites
● Driver installation
● Confirm the name or IP address of the device (if adding a standard TCP/IP port).
To add a standard TCP/IP port, you need to enter the name or IP address of the device. For the name of the
device, use the name by which the device is known on the network. If you do not know the device name or IP
address, check with your network administrator.
● Determining to protocol to use
Raw: A protocol that can be used with Windows. It transmits data at a higher speed than LPR.
LPR: The protocol commonly used by TCP/IP.
Procedures
2 Right-click the icon of the device you are going to set → select [Printer properties].
If you are using a touch panel, press and hold the icon of the device you want to set → tap [Printer properties]
in the pop-up menu.
3 Display the [Ports] sheet → click [Add Port].
51
4 In the [Printer Ports] dialog box, select [Standard TCP/IP Port] from [Available port
types] → click [New Port].
5 Proceed with the operation according to the instructions on the wizard, then enter the
device name or IP address.
[Port Name] is automatically entered. Change the port name if required.
If the [Additional port information required] screen is displayed, click the subsequent "Open details" and
perform the necessary operations.
Perform one of the following.
- Return to the previous screen in the wizard → re-enter the information for [Printer Name or IP Address] →
click [Next].
- Select [Device Type] > [Standard] > [Canon Network Printing Device with P9100] → click [Next].
Depending on the device you are using, the name you select in [Device Type] > [Standard] may differ from
[Canon Network Printing Device with P9100].
6 Click [Finish].
52
7 In the [Printer Ports] dialog box, click [Close].
8 Click [Configure Port].
9 Set the port.

When using Raw
Select [Protocol] > [Raw] → click [OK].
When using LPR
(1) Select [Protocol] > [LPR] → specify one of the following print queues for [LPR Settings] > [Queue Name].
LP: Outputs according to the spool setting of the device. This is the setting that is normally used.
SPOOL: Always outputs after spooling to the hard disk, regardless of the device settings.
DIRECT: Always outputs without spooling to the hard disk, regardless of the device settings.
(2) Click [OK].
53
10 Click [Close].
54
Making the Device Functions Usable
When installing a driver with a network connection, normally, information about options installed in the device
is retrieved and functions associated with the driver are set so that they can be used. When the functions of the
device cannot be used, or when an option is added, the device information must be reacquired and the option
structure manually set.
Prerequisites
● Settings at the device
Enable [Use WSD Browsing] at the device. If you are using a device that does not support this function,
enable [Retrieve Printer Mngt. Information from Host].
For details, refer to the manual of the device.
Procedures
2 Right-click the icon of the device you are going to set → select [Printing preferences].
If you are using a touch panel, press and hold the icon of the device you want to set → tap [Printing
preferences] in the pop-up menu.
3 Display the [Support/Device] sheet.
55
NOTE
● If the Windows standard print settings screen, which does not have a [Support/Device] sheet, is displayed,
there could be a problem with the environment, settings, or installation state of the driver. Refer to the
subsequent troubleshooting to enable the print settings screen of the driver to be displayed.
4 Click [Device Settings].

When you click [Device Settings], after a confirmation screen asking whether you want to save the settings is
displayed, the print settings screen closes.
5 Display the [Device Settings] sheet.
6 If necessary, set whether the IP address of the device is to be automatically detected

or manually specified in [IP Address Settings] at the bottom of the screen.
7 Click [Retrieve Device Information].
56
8 When the message "Do you want to retrieve the device information?" is displayed,
click [Yes].
If the information is retrieved, the option structure is set automatically. Check the settings.
If the information is not retrieved, set the options manually. Select the options attached to the device.
9 Click [OK].
NOTE
● When installing a driver by discovering the corresponding device on a network, some of the device
information may not be obtainable if WSD communication is disabled. If this is the case, you can correctly
acquire device information by performing the above procedure.
● In any of the following cases, some of the device information may not be obtainable. If this is the case, set
the options manually.
- When the device is connected by USB
- When installing the driver by specifying a standard TCP/IP port
- When using a device or port that cannot acquire device information
Related Topics
57
Printing
Printing
Printing .................................................................................................................................................................. 59
Printing from a Desktop App .............................................................................................................................. 60
Printing from a Store App ................................................................................................................................... 63
Scaling .................................................................................................................................................................. 69
Attaching a Watermark ...................................................................................................................................... 70
Printing a Large Poster over Multiple Pages ..................................................................................................... 71
Overlapping Print Data on a Fixed Form ............................................................................................................ 75
Attaching a PIN to Print Data ............................................................................................................................. 77
Encrypting Print Data .......................................................................................................................................... 78
Putting Print Jobs on Hold .................................................................................................................................. 80
Storing Print Data ................................................................................................................................................ 81
Prioritizing a Print Job over Other Print Jobs ..................................................................................................... 82
Suspend Currently Printing Jobs to Prioritize a Print Job .................................................................................. 83
Changing the Default Settings ........................................................................................................................... 84
58
Printing
Printing

Printing from a Store App(P. 63)
Scaling(P. 69)
Attaching a Watermark(P. 70)
Printing a Large Poster over Multiple Pages(P. 71)
Overlapping Print Data on a Fixed Form(P. 75)
Attaching a PIN to Print Data(P. 77)
Encrypting Print Data(P. 78)
Putting Print Jobs on Hold(P. 80)
Storing Print Data(P. 81)
Prioritizing a Print Job over Other Print Jobs(P. 82)
Suspend Currently Printing Jobs to Prioritize a Print Job(P. 83)
Changing the Default Settings(P. 84)
59
Printing
Printing from a Desktop App
This explains the basic procedure for displaying the print settings screen of the driver and printing from a
desktop app.
NOTE
● When using a device connected via a WSD port, enable [Use WSD] at the device.
● If you are using the battery saver in Windows 10, print after plugging in your computer or after deactivating
the battery saver in [Settings] > [System] > [Battery].
1 Select [Print] from the menu of the app.
2 In the print screen, select the device you are using → click [Preferences], [Printer
properties], or [Properties].
60
Printing
3 In the print settings screen of the driver, set the required items.
You can switch sheets if necessary.
The current settings are illustrated in the preview. By clicking the preview, you can set basic print functions
such as two-sided printing, binding location, page layout, etc.
61
Printing
NOTE
● If the Windows standard print setting screen, which differs from the screen above, is displayed, it may be due
to an error in the environment, settings, or installation state of the driver. Refer to the troubleshooting to
enable the print settings screen of the driver to be displayed.
● If the function you want to use is not displayed in the print settings screen, configure the print settings after
enabling the functions of the device by retrieving the device information etc.
4 Click [OK].
5 In the print screen, click [Print] or [OK].
Related Topics
About This Driver(P. 9)
62
Printing
Printing from a Store App
This explains the basic procedure for displaying the print settings screen of the driver and printing from a store
app.
If functions you want to use are not displayed in the print settings screen displayed from a store app, you may
be able to use them by changing the default settings.
For details about the print settings from store apps, refer to the user's guide for Canon Office Printer Utility.
NOTE
● When using a device connected via a WSD port, enable [Use WSD] at the device.
● When printing in Windows 10, check that both [Let apps run in the background] and [Canon Office Printer
Utility] are enabled in [Settings] > [Privacy] > [Background apps] in Windows.
To Print from a Store App in Windows 10
1 Select [Print] from the menu of the app.
2 In the print screen, select the device you are using → click [More settings].
63
Printing
NOTE
64
Printing
4 Click [OK].
5 In the print screen, click [Print].
NOTE
● If you are using the battery saver of Windows, you may not be able to print due to there being an insufficient
charge in the battery. If that is the case, print after doing one of the following.
- Plug in your computer
- Enable background execution of the Canon Office Printer Utility in the battery settings
To do so, perform the following procedure.
(1) Click [See which apps are affecting your battery life] in [Settings] > [System] > [Battery].
(2) In the displayed screen, select [Show] > [All Apps].
(3) Select [Canon Office Printer Utility] → disable [Let Windows decide when this app can run in the
background], then select [Allow the app to run background tasks].
Alternatively, print after deactivating the battery saver in [Battery].
65
Printing
To Print from a Store App in Windows 8.1/Server 2012 R2
1 Display the data you want to print in the app.
2 Display the charm bar, then click [ Devices] → [ Print] → the device you are
using.
3 Click [More settings].
66
Printing
NOTE
67
Printing
5 Click [ ] (Back).
6 In the print screen, click [Print].
Related Topics
About This Driver(P. 9)
68
Printing
Scaling
You can enlarge or reduce the print data when printing.
To scale to the output page size
1 Display the [Main] sheet.
2 Check that the paper size set in the app is displayed in [Page Size].
To change the page size, click [Details] → select the paper size from [Page Size] → click [OK].
3 Select the paper size you want to print on from [Output Size].
To specify a desired scale
2 Click [Page Size] > [Details].
3 In the [Detailed Settings] dialog box, check that the paper size set in the app is
displayed in [Page Size].
To change the page size, select the paper size from [Page Size].
4 Select [Specify print ratio].

If necessary, set a ratio and select [Origin Point for Specified Ratio].
5 Click [OK].
Related Topics
[Main] Sheet(P. 120)
Registering Custom Paper Sizes(P. 98)
69
Printing
Attaching a Watermark
You can superimpose and print semi-transparent characters such as [TOP SECRET] or [DRAFT] over print data.
You can also create new watermarks.
To Attach and Print a Watermark
1 Display the [Layout] sheet.
2 Select [Insert Watermark] → select a watermark name.
To Create New Watermarks
2 Click [Insert Watermark] > [Details].
3 In the [Edit Watermark] dialog box, click [Add].
4 Enter a name in [Name].

If necessary, enter the characters and set the attributes, positioning, border, and superimposition of the
watermark.
5 Click [OK].
6 Click [Close].
The created watermark is added to the [Insert Watermark] list.
Related Topics
[Layout] Sheet(P. 123)
70
Printing
Printing a Large Poster over Multiple Pages
You can enlarge the print data of one page and print it over multiple sheets of paper. When the output sheets
are joined together, they form a large print like a poster.
This topic also introduces poster printing setting and output examples.
Poster Printing Setting and Output Examples(P. 71)
To Perform Poster Printing
2 Select [Poster] → specify the number of parts.

If you have selected [Custom], specify the number of rows and columns respectively in the [Specify Custom
Number of Rows and Columns for Poster] dialog box.
If you want to set details such as the range of pages to be printed, printing with border lines, etc., perform the
following procedure.
3 Click [Details].
4 In the [Poster Settings] dialog box, set any necessary items.
5 Click [OK].
Poster Printing Setting and Output Examples

This shows combinations of setting examples and output results relating to poster printing. The setting
examples are shown in combination with the setting state in the [Poster Settings] dialog box whenever
required.
Setting Example 1.
● [Main] sheet > [Orientation]: [Portrait]
● [Layout] sheet > [Poster]: [1 x 2]
71
Printing
Output Result
Setting Example 2.
● [Main] sheet > [Orientation]: [Portrait]
● [Layout] sheet > [Poster] > [Custom]: Set 3 for [Number of Rows] and 2 for [Number of Columns]
Output Result
When [Poster Settings] dialog box > [Rotate sheets 90 degrees] > [On] or [Auto] is selected
If you select [Auto], the pages are oriented in the direction in which the print data is printed larger. In this
example, the orientation is the same as when [On] is selected.
When [Poster Settings] dialog box > [Rotate sheets 90 degrees] > [Off] is selected
Setting Example 3.
● Detailed settings in the [Poster Settings] dialog box
72
Printing
Output Result
Setting Example 4.
● Detailed settings in the [Poster Settings] dialog box
73
Printing
Output Result
Legend
Broken line: border
: paste mark
: cut mark
: Margin Width
Related Topics
74
Printing
Overlapping Print Data on a Fixed Form
You can print data overlapping a fixed form stored in the device. This function is known as overlay printing.
If you are using a created fixed form, you must save it beforehand in the device.
To Save a Fixed Form in the Device
1 Select [Print] from the menu of the app → display the print settings screen of the
driver.
3 Click [Overlay].
4 In the [Overlay Settings] dialog box, select [Processing Method] > [Create a form file] →
specify a file name in [File Name] → click [OK].
5 In the print settings screen, click [OK].
6 In the print screen, click [Print] or [OK].
To Perform Overlay Printing
2 Click [Overlay].
3 In the [Overlay Settings] dialog box, select [Processing Method] > [Use Overlay Print].
4 Click [Retrieve Form File Information] → select the form file to use from [File List].
If you cannot acquire information from the device, enter the form file name in [File Name].
75
Printing
5 When performing two-sided printing, select which side to apply overlay printing to in
[Apply To].
6 Click [OK].
Related Topics
76
Printing
Attaching a PIN to Print Data
You can attach a PIN to print data and save it in the device. This is useful when printing confidential documents
etc.
NOTE
● If you register the PIN used in secured printing as a default setting, you can reduce the effort required to
configure settings when printing.
2 Select [Secure Print] from [Output Method].
3 In the [Secure Print Settings] dialog box, enter [PIN] → click [OK].
If necessary, enter [PIN] after selecting [Use a PIN].
Related Topics
Confirming Set User Information Prior to Printing(P. 114)
77
Printing
Encrypting Print Data
You can send print data to the device in an encrypted state. This alleviates the risk of data manipulation and
information leakage occurring in the communication path through which the print data is being sent. This
function is called Encrypted Secure Print.
The saved data can be printed by entering the password in the control panel of the device.
To use this function, you need to enable the Encrypted Secure Print function in the option settings of the device.
To Enable the Encrypted Secure Print Function

4 Enable [Encrypted Secure Print] in [Option List].

If necessary set the encryption level.
5 Click [OK].
NOTE
● In a shared printer environment, it is necessary to enable the CSR (Client Side Rendering) function of
Windows on the server side. You can enable the CSR function by the following method.
(1) Right-click the icon of the printer you are using → click [Printer properties].
(2) Display the [Sharing] sheet → check that [Share this printer] is selected → select [Render print jobs on
client computers].
To Print with Encryption
78
Printing
2 Select [Secure Print] from [Output Method].
3 In the [Secure Print Settings] dialog box, select [Use a password for Encrypted Secure
Print] → enter [Password] → click [OK].
You may need to enter a PIN instead of a password.
NOTE
● If you register the password used in Encrypted Secure Print as a default setting, you can reduce the effort
required to configure settings when printing.
● If you printed without setting a password, the print job is cancelled.
When registering Encrypted Secure Print settings as a favorite, check that [Preferences] > [Store
authentication information in favorite settings] in the [Support/Device] sheet is enabled. If [Store
authentication information in favorite settings] is disabled, the password is not stored in favorites.
Related Topics
[Support/Device] Sheet(P. 135)
[Device Settings]/[Administrator Settings] Sheet(P. 137)
79
Printing
Putting Print Jobs on Hold
You can temporarily save a print job in a hold queue in the device. You can change the print order or settings of
stored jobs from the control panel of the device or the Remote UI.
2 Select [Hold] from [Output Method].
3 In the [Settings for Document to Hold] dialog box, set [Document Name].
If you want to specify a desired name, select [Enter name] → enter the name.
4 Click [OK].
When performing hold printing, you can confirm or set the name of data in the displayed screen.
Related Topics
80
Printing
Storing Print Data
You can store the print data in a box in the device. You can also change the settings of or combine the stored
data with other stored data from the control panel of the device or the Remote UI.
NOTE
● If you register the box number used in stored printing as a default setting, you can reduce the effort required
to configure settings when printing.
2 Select [Store in Mail Box/Store in Box] from [Output Method].
3 In the [Storage Settings] dialog box, set [Document Name].

If you want to specify a desired name, select [Enter name] → enter the name.
4 Click [Retrieve Mail Box Information/Retrieve Box Information] → select a storage

destination from [Mail Box/Box].
You may be able to simultaneously select multiple boxes by pressing the [Ctrl] or [Shift] key.
5 Click [OK].
Related Topics
81
Printing
Prioritizing a Print Job over Other Print Jobs
You can print a document with higher priority than other print jobs that are in a standby state in the device.
When executing priority printing, if there is a print job being processed at the device, priority printing is started
as soon as that job is finished.
2 Select [Priority Print] from [Output Method].
Related Topics
82
Printing
Suspend Currently Printing Jobs to Prioritize a Print Job
You can cancel the print job currently being processed by the device and print the specified job.
This function is useful when the print job being processed is taking time and you want to print another print job
before it.
The suspended print job is restarted after the interrupting print job is finished.
2 Select [Interrupt and Print] from [Output Method].
Related Topics
83
Printing
Changing the Default Settings
You can change the default settings to the desired print settings. If you change them to settings that you use
frequently, you can reduce the effort required to configure settings when printing.
2 Right-click the icon of the device you are going to set → select [Printing preferences].
If necessary, switch sheets and configure relevant settings.
4 Click [OK].
Related Topics
84
Creating a Booklet
Creating a Booklet
Creating a Booklet ........................................................................................................................................... 86
Booklet Printing .................................................................................................................................................. 87
Creating a Booklet in Sets ................................................................................................................................... 88
Correcting Displacement During Booklet Printing ........................................................................................... 89
Saddle Stitched Booklet Printing ........................................................................................................................ 90
Saddle Press Processing When Creating Saddle Stitched Booklets .................................................................. 91
Trimming Pages When Creating Saddle Stitched Booklets ............................................................................... 92
Perfect Binding .................................................................................................................................................... 93
Printing Page Numbers in the Same Position on the Front and Back of Each Page ........................................ 94
85
Creating a Booklet
Creating a Booklet
Booklet Printing(P. 87)

Creating a Booklet in Sets(P. 88)
Correcting Displacement During Booklet Printing(P. 89)
Saddle Stitched Booklet Printing(P. 90)
Saddle Press Processing When Creating Saddle Stitched Booklets(P. 91)
Trimming Pages When Creating Saddle Stitched Booklets(P. 92)
Perfect Binding(P. 93)
Printing Page Numbers in the Same Position on the Front and Back of Each Page(P. 94)
86
Creating a Booklet
Booklet Printing
You can print with the pages automatically arranged so they create a booklet when folded in half.
1 Display the [Main] or [Layout] sheet.
2 Select [Booklet Printing].

To set the binding position and gutter, follow the procedures below.
3 Click [Details].
4 In the [Booklet Settings] dialog box, select the binding direction when performing
booklet printing from [Binding].
5 Specify the width in [Gutter Width].
6 Click [OK].
Related Topics
Creating a Booklet in Sets(P. 88)
Correcting Displacement During Booklet Printing(P. 89)
87
Creating a Booklet
Creating a Booklet in Sets
When creating a booklet from a document with a large number of pages, you can divide the pages into multiple
sets and print them.
2 Select [Booklet Printing] → click [Details].
3 In the [Booklet Settings] dialog box, select [Divide into sets for booklet layout].
4 Select the dividing method from [Divide into Sets].

If dividing manually, specify how many pages are in each set.
When dividing manually and performing booklet printing with saddle stitching, specify a value equal to or
lower than the maximum number of pages the device can saddle stitch. For the maximum number of pages
that can be saddle stitched, refer to the manual of the device.
5 Click [OK].
Related Topics
88
Creating a Booklet
Correcting Displacement During Booklet Printing
You can create and print booklets while correcting displacement between outer and inner pages that occurs
during booklet printing. If you trim the edges of the pages using a trimmer, you can adjust the amount of
margin so that the position of the print data on the page does not deviate between pages.
2 Select [Booklet Printing] → click [Details].
3 In the [Booklet Settings] dialog box, select [Use creep (displacement) correction].
4 Select a correction method in [Correction Method].

If correcting manually, specify a correction amount in [Correction Amount].
5 Click [OK].
Related Topics
89
Creating a Booklet
Saddle Stitched Booklet Printing
When performing booklet printing, you can specify stapling in the center of the output pages. The pages are
divided into sets and folded in half, and each set is saddle stitched in the center.

You can also set [Booklet Printing] in the [Layout] sheet.
3 Select [On] from [Staple] → select [Saddle stitch] as the stapling position.
You can also set [Staple] in the [Finishing] sheet.
Related Topics
[Finishing] Sheet(P. 129)
90
Creating a Booklet
Saddle Press Processing When Creating Saddle Stitched

Booklets
When performing saddle stitched booklet printing, you can press the bound portion so that it is flattened.

4 Click [Booklet Printing] > [Details].
5 In the [Booklet Settings] dialog box, select [Saddle Press] → specify the force of saddle
press processing in [Saddle Press Adjustment].
6 Click [OK].
Related Topics
91
Creating a Booklet
Trimming Pages When Creating Saddle Stitched

Booklets
When stapling in the middle to form a booklet, you can trim and align the edges of the pages.

4 Display the [Finishing] sheet.
5 Select [Trim].
To set a trim width adjustment method, follow the procedure below.
6 Click [Details].
7 In the [Adjust Trim Width] dialog box, set a trim width adjustment method.
If [Adjust By] is displayed, selecting [Finishing width] trims the pages to the specified height and width after
finishing.
8 Click [OK].
Related Topics
92
Creating a Booklet
Perfect Binding
You can apply glue to the gutter side of the contents and encloses them in a cover to create a booklet.
2 Select [Perfect Binding] → click [Details].
3 In the [Perfect Binding Settings] dialog box, set the required items.
When printing on the cover
Display the [Basic Settings] sheet → set [Perfect Binding Cover Settings] > [Cover Printing].
When adjusting the finishing size
Display the [Basic Settings] sheet → select [Finishing Settings] > [Specify By].
If you select [Finishing size], select a finished page size from [Finishing Size]. The cover and content pages are
trimmed to match the finished size.
If you select [Trim width], specify the trim widths in [Trim Width (Fore)] and [Trim Width (Top/Bottom)].
In the [Finishing Adjustments] sheet, you can adjust the print positions of the content pages and cover, and
the trimming angles and positions.
4 Click [OK].
Related Topics
93
Creating a Booklet
Printing Page Numbers in the Same Position on the

Front and Back of Each Page
When performing booklet printing and two-sided printing, you can print page numbers so that they are in the
same position on both the front and back of each page. For example, if you specify the side opposite the gutter,
the page number is attached as in a paperback book.
If you specify the print position of the page number as lower right, the printed result if you enable this function
will be as follows.
With booklet printing With two-sided printing
Here, the procedure where this function is used with booklet printing is explained.

You can also set [Booklet Printing] in the [Main] sheet.
NOTE
● Where this function is used with two-sided printing, set [2-Sided Printing] in the [Main] sheet.
3 Click [Header/Footer].
4 In the [Header/Footer Settings] dialog box, display [Print Information] sheet.
5 Select the print position for page numbers in [Output Sheets] > [Page Number].
6 Select [Output Sheets] > [Print so that the position overlaps on the front and back sides
of the paper].
7 Click [OK].
94
Creating a Booklet
Related Topics
95
Using Various Types of Paper

Using Various Types of Paper .................................................................................................................... 97
Registering Custom Paper Sizes ......................................................................................................................... 98
Inserting Sheets Between Transparencies ........................................................................................................ 99
Inserting Sheets ................................................................................................................................................ 100
Inserting Tab Paper ........................................................................................................................................... 101
Printing on Tab Paper ....................................................................................................................................... 102
96

Inserting Sheets Between Transparencies(P. 99)
Inserting Sheets(P. 100)
Inserting Tab Paper(P. 101)
Printing on Tab Paper(P. 102)
97
Registering Custom Paper Sizes
You can register a desired paper size and use it for printing. You can also use registered custom paper sizes to
print with other devices from the computer you are using.
2 Click [Custom Paper].
3 In the [Custom Paper Settings] dialog box, click [Add].
4 In the [Edit Custom Paper] dialog box, configure detailed settings such as the name,
dimensions, etc. of the custom paper size → click [OK].
5 Click [OK].
Related Topics
98
Inserting Sheets Between Transparencies
You can print with sheets of paper inserted between transparencies. You can also print on the inserted sheets.
1 Display the [Paper Feed] sheet.
2 Select transparency from [Paper Type].

You can select transparency from among the following.
- The [Paper Type] drop-down list.
- [Paper Type] in the [Paper Type Settings] dialog box.
You can display the [Paper Type Settings] dialog box by selecting [Select Paper By] > [Paper Type] then
clicking [Settings], or clicking [Paper Type] > [Settings].
3 Select the paper source for transparencies from [Paper Source for Transparencies] or
[Paper Source].
4 Select [On] or [Print on cover sheets] from [Cover Sheets].
5 Select the paper source that the sheets for insertion are set in from [Specify Cover
Sheets By] > [Paper Source] or [Paper Source for Cover Sheets].
6 To change the paper type of the sheets to be inserted, click [Specify Cover Sheets By] >
[Paper Type] or [Settings] from [Paper Type for Cover Sheets] → select the paper type →
click [OK].
Related Topics
[Paper Feed] Sheet(P. 127)
99
Inserting Sheets
You can insert sheets of paper between specified pages.
2 Select [Insert Sheets] → click [Settings].
3 In the [Sheet Insertion Settings] dialog box, select [Inserted sheets] from [Sheets to
Insert].
4 Set [Paper Source], [Inserted Sheets/Tab Paper] and [Insertion Position].
5 Click [OK].
Related Topics
100
Inserting Tab Paper
You can insert tab paper between specified pages. You can also print on the tab part.
2 Select [Insert Sheets] → click [Settings].
3 In the [Sheet Insertion Settings] dialog box, select tab paper from [Sheets to Insert].
4 Set [Paper Source], [Inserted Sheets/Tab Paper] and [Insertion Position].
5 To change the paper type, click [Paper Type for Tab Paper] > [Settings] → select the
paper type to be used from [Paper Type].
To set the tab paper size and print position on the tab part, follow the procedure below.
If setting is unnecessary, click [OK] to close the [Paper Type Settings] dialog box.
6 Click [Tab Details].
7 In the [Tab Settings] dialog box, select the paper size from [Tab Paper Size].
8 Select [Offset printing position] → specify [Offset Width] → click [OK].

If you have created print data with one of the following paper sizes, do not select [Offset printing position].
The tab part is included in the width.
- A4 tab paper: 223 x 297 mm (8.77 x 11.69 inches)
- Letter tab paper: 228.6 x 279.4 mm (9.00 x 11.00 inches)
9 Click [OK].
Related Topics
101
Printing on Tab Paper
You can print on the tab part of tab paper.
2 Click [Paper Type] > [Settings].

If you can select [Select Paper By], select [Paper Type], then click [Settings].
3 In the [Paper Type Settings] dialog box, select tab paper from [Paper Type].
4 Click [Tab Details].

The [Tab Settings] dialog box is displayed.
5 Select [Offset printing position] → specify [Offset Width].

If you have created print data with one of the following paper sizes, do not select [Offset printing position].
The tab part is included in the width.
- A4 tab paper: 223 x 297 mm (8.77 x 11.69 inches)
- Letter tab paper: 228.6 x 279.4 mm (9.00 x 11.00 inches)
If you can select [Tab Paper Size], select a paper size.
6 Click [OK].
7 In the [Tab Settings] dialog box, click [OK].
Related Topics
102
Editing Favorite Settings

Editing Favorite Settings ........................................................................................................................... 104
Registering Favorite Settings ........................................................................................................................... 105
Editing the Favorite Settings List ..................................................................................................................... 106
103
Registering Favorite Settings(P. 105)

Editing the Favorite Settings List(P. 106)
104
Registering Favorite Settings
You can recall frequently used print settings when printing by registering those settings in [Favorite Settings].
1 In the print settings screen of the driver, configure the settings you want to register.
If necessary, switch sheets and configure relevant settings.
2 Click [Register] at the bottom of the [Favorite Settings] list.
3 In the [Register Favorite Settings] dialog box, select [Name] and [Icon].
Enter text if required in [Comment].
4 Click [OK].
Related Topics
Common Settings for All Sheets(P. 118)
105
Editing the Favorite Settings List
You can edit the [Favorite Settings] list, and import or export it to be used on other computers.
NOTE
● You cannot edit print settings registered in favorite settings. If you want to use different print settings as
favorite settings, register them as new favorite settings.
To Edit the Favorite Settings List
2 Click [Edit Favorite Settings].
3 Select the favorite settings you want to edit from the [Favorite Settings] list → click
[Edit].
If you want to delete favorite settings, select the favorite settings → click [ ] (Delete) → click [Yes] in the
displayed verification screen.
4 In the [Edit Favorite Settings] dialog box, select [Name] and [Icon] → click [OK].
Enter text if required in [Comment].
5 Click [Close].
To Export Favorite Settings
3 Select the favorite settings to be exported from [Favorite Settings].
4 Click [Export] → specify the storage location and file name → click [Save] or [OK].
The selected favorite settings are saved in a file with the extension ".profile".
106
To Import Favorite Settings
3 Select [Import] → select the file (with the extension ".profile") to be imported → click
[Open].
The imported favorite settings are displayed in the [Favorite Settings] list.
Related Topics
107
Coordinating with the Device Functions
Coordinating with the Device

Functions
Coordinating with the Device Functions .......................................................................................... 109
Setting the Authentication Function ............................................................................................................... 110
Setting the User Name ...................................................................................................................................... 112
Confirming Set User Information Prior to Printing ......................................................................................... 114
108
Setting the Authentication Function(P. 110)

Setting the User Name(P. 112)
109
Setting the Authentication Function
You can manage printing by means of the department ID management function or the user authentication
function.
To set the authentication function, you need to enable the function in the device settings.
To Enable the Authentication Function

4 Select [Authentication Function] → click [Settings].
5 In the [Authentication Function Settings] dialog box, select the function → click [OK].
6 Click [OK].
To Set the Authentication Information
NOTE
● If you register the authentication information as a default setting, you can reduce the effort required to
configure settings when printing.
2 Click [Authentication Information Settings].
110
3 In the displayed screen, enter the authentication information set in the device.
4 Click [OK].
Related Topics
111
Setting the User Name
You can set a user name to be used for print jobs. The set user name is displayed on the control panel of the
device, and is printed as the user name for headers or footers.
To change the user name, you need to allow changes in the device settings.
To Allow User Name Changes

3 Display the [Administrator Settings] sheet.
4 Click [Change Administrator Settings].

If a screen asking you to confirm whether you want to allow changes is displayed, click [Yes] → display the
[Administrator Settings] sheet.
5 Enable [List of Settings] > [Allow changes to user name] → click [OK].
To Set the User Name
2 Click [User Name Settings].
3 In the [User Name Settings] dialog box, select [Name to Use] → click [OK].
Related Topics
112
113
Confirming Set User Information Prior to Printing
You can check the user information you have set before executing printing.
When you set this function, a screen enabling you to check user information is displayed when you execute
printing. You can also reset the information if required.
The user information that you can check is the PIN (or password) you set for secure printing and the
authentication information you set for print management using the department ID management function or
the user authentication function.
Prerequisites
● You are using Windows 10 Version 1803 or later
● Canon Office Printer Utility is installed
● The system is correctly set to that the confirmation screen is displayed
Enable both [Let apps run in the background] and [Canon Office Printer Utility] in [Settings] > [Privacy] >
[Background apps] in Windows.
Procedures

3 Display the [Administrator Settings] sheet.
4 Click [Change Administrator Settings].

If a screen asking you to confirm whether you want to allow changes is displayed, click [Yes] → display the
[Administrator Settings] sheet.
5 Enable [List of Settings] > [Always confirm user information when printing] → click
[OK].
NOTE
● If you are using the battery saver of Windows, the screen for confirming user information may not be
displayed due to there being an insufficient charge in the battery. If that is the case, print after doing one of
the following.
- Plug in your computer
- Enable background execution of the Canon Office Printer Utility in the battery settings
To do so, perform the following procedure.
114
(1) Click [See which apps are affecting your battery life] in [Settings] > [System] > [Battery].
(2) In the displayed screen, select [Show] > [All Apps].
(3) Select [Canon Office Printer Utility] → disable [Let Windows decide when this app can run in the
background], then select [Allow the app to run background tasks].
Alternatively, print after deactivating the battery saver in [Battery].
Related Topics
115
Settings List
Settings List
Settings List ....................................................................................................................................................... 117
Common Settings for All Sheets ....................................................................................................................... 118
[Main] Sheet ....................................................................................................................................................... 120
[Layout] Sheet .................................................................................................................................................... 123
[Paper Feed] Sheet ............................................................................................................................................. 127
[Finishing] Sheet ................................................................................................................................................ 129
[Quality] Sheet ................................................................................................................................................... 131
[Covers] Sheet .................................................................................................................................................... 134
[Support/Device] Sheet ..................................................................................................................................... 135
[Device Settings]/[Administrator Settings] Sheet ........................................................................................... 137
116
Settings List
Settings List

[Quality] Sheet(P. 131)
[Covers] Sheet(P. 134)
117
Settings List
Common Settings for All Sheets
You can set basic print functions via the settings preview in each of the sheets. You can also view favorite
settings, return the print settings to their standard configurations, etc.
Settings Preview
Displays the current print settings in a preview. You can set basic print functions by clicking on the preview.
Display the settings preview guide
Switch between 1-sided/2-sided printing
Staple
Click where you want the page to be stapled. When
setting up booklet printing, you can switch saddle
stitching on and off.
Binding Location
Click the edge of the page where you want to set
the binding location.
Rotate wheel/pinch: change page layout

You can change the number of pages arranged on
each sheet of paper.
You can change the number of pages by rotating
the mouse wheel over the settings preview. If you
are using a touch panel display, you can change the
number of pages by pinching in and out over the
settings preview.
[Favorite Settings]
Displays a list of registered favorite settings.
[Register]
Enables you to register the current print settings as favorite settings.
☞ [Register Favorite Settings] Dialog Box
[Name]
Specifies a name to attach to the favorite settings.
[Icon]
Specifies an icon to attach to the favorite settings.
[Comment]
Specifies a comment about the favorite settings. Enter if required.
[View Settings]
Displays the content of the favorite settings.
[Reset Print Settings]

Returns the print settings of all sheets to their standard configurations.
[Restore Defaults]
Returns the print settings of the open sheet to their standard configurations.
118
Settings List
Related Topics
119
Settings List
[Main] Sheet
You can set basic print functions.
[Page Size]
Displays the page size set in the app or the page size set by clicking [Details].
[Details]
Enables you to set the document size and enlargement or reduction.
Paper sizes displayed with the ( ) icon can only be specified as the paper size in the print data. They are
not supported as paper sizes to actually print on.
[Output Size]
Specifies the actual page size you want to print on. If you select a size that differs from [Page Size], the print
data is enlarged or reduced to fit the set page size when printing.
[Orientation]
Specifies the orientation of print data.
[Copies]
Specifies the number of copies to be printed.
[Paper Type]
Specifies the paper to print on by paper type.
[2-Sided Printing]
Prints on both sides of the paper. The default setting for printers that support 2-sided printing is [2-Sided
Printing].
[Binding Location]
Specifies the binding location.
[Details]
Enables you to set the width of the gutter. When a gutter is set, the print area narrows only by the amount of
the gutter width. If you select [Image Adjustment to Fit Gutter] > [Reduce image], the print data is reduced so
as to fit into the print area. If you select [Shift image], the print data is shifted and arranged as is. In this case,
some of the data that is not within the print area may not be printed.
[Booklet Printing]
Prints with the pages of a document arranged so that it can be folded in half to create a booklet.
[Details]
Enables you to configure detailed settings when performing booklet printing such as the opening direction
and gutter width.
☞ [Booklet Settings] Dialog Box
[Binding]
Specifies whether a document opens to the right or left when creating a booklet.
120
Settings List
[Gutter Width]
Specifies the gutter width.
[Divide into sets for booklet layout]
Creates a booklet in multiple sets. Select whether to automatically or manually divide into sets in [Divide into
Sets]. If dividing manually, specify how many pages are in each set in [Sheets per Set].
[Use creep (displacement) correction]
Corrects displacement between outer and inner pages that occurs during booklet printing. Select a
correction method from [Correction Method]. If correctly manually, specify a correction amount in
[Correction Amount].
[Saddle Press]
Performs saddle press processing when creating a saddle stitched booklet. You can specify the force of
saddle pressing in [Saddle Press Adjustment].
NOTE
● [Main] or [Layout] sheet > [Booklet Printing] cannot be set at the same time as the following settings.
- Settings other than [Covers] sheet > [Configure front cover settings] > [Front Cover] > [Leave blank]
- [Covers] sheet > [Configure back cover settings]
[Page Layout]
Prints with multiple pages arranged on one sheet.
[Staple]
Staples the pages when outputting print data. Select staple position(s).
[On (Eco (Staple-Free))] crimps the paper without using staples.
The available staple positions vary depending on the output paper size, paper feed direction, and paper
source method.
[Color Mode]
Switches between printing in color or in black-and-white.
NOTE
● If you select [Color Mode] > [Color], by default, whether each page is color or grayscale will be determined
and the color mode switched accordingly.
● To print all pages in color, disable [Troubleshooting] > [Auto (color/B&W)] in the [Support/Device] sheet.
[Output Method]
Sets the method for outputting print data. You can set a PIN in the print data or store the print data in the
device.
[Print]
Performs normal printing.
[Hold]
Saves print data in a hold queue (temporary storage area) in the device. You can change the print order or
settings of the stored data from the control panel of the device or the Remote UI.
The file name is displayed in the device. If you select [Document Name] > [Enter name] in the [Settings for
Document to Hold] dialog box displayed by clicking [Settings], you can specify a desired name.
[Secure Print]
Attaches a PIN to print data and save it in the device. This function is useful when printing confidential
documents etc. If you enable the Encrypted Secure Print function, you can encrypt and print data and attain a
stronger effect from the aspect of security.
121
Settings List
The saved data can be printed by entering the PIN in the control panel of the device.
NOTE
● If you have enabled [PIN-protected printing] in the Windows print options and print using the driver, the
print job will normally be output as a secure print.
[Store in Mail Box/Store in Box]

Saves the print data to a box in the device. You can change the settings of or combine the stored data from
the control panel of the device or the Remote UI.
[Priority Print]
Prints with priority over other print data that is waiting to be printed by the device.
[Interrupt and Print]

Cancels the print job currently being processed by the device and prints the specified job.
[Scheduled Print]
Prints at a set time.
When a time is set, the set time is displayed when the pointer hovers over [Scheduled Print].
If the time set on the device and that set on the computer you are using do not match, the print job may not
print at the set time or printing may be canceled.
[Custom Paper]
Enables you to register a desired paper size that you can use for printing.
Items with ( ) attached are standard paper sizes and cannot be edited or deleted.
Related Topics
Scaling(P. 69)
Putting Print Jobs on Hold(P. 80)
Storing Print Data(P. 81)
122
Settings List
[Layout] Sheet
You can select a layout or set page modifications when printing.
[Booklet Printing]
Prints with the pages of a document arranged so that it can be folded in half to create a booklet.
[Details]
and gutter width.
☞ [Booklet Settings] Dialog Box
[Binding]
Specifies whether a document opens to the right or left when creating a booklet.
[Gutter Width]
Specifies the gutter width.
[Divide into sets for booklet layout]
Creates a booklet in multiple sets. Select whether to automatically or manually divide into sets in [Divide into
Sets]. If dividing manually, specify how many pages are in each set in [Sheets per Set].
[Use creep (displacement) correction]
Corrects displacement between outer and inner pages that occurs during booklet printing. Select a
correction method from [Correction Method]. If correctly manually, specify a correction amount in
[Correction Amount].
[Saddle Press]
Performs saddle press processing when creating a saddle stitched booklet. You can specify the force of
saddle pressing in [Saddle Press Adjustment].
NOTE
[Perfect Binding]
Applies glue to the gutter side of the contents and encloses them in a cover to create a booklet.
[Details]
and paper size.
☞ [Perfect Binding Settings] Dialog Box
[Basic Settings] Sheet

[Binding]
Sets whether a document opens to the right or left when creating a booklet.
[Perfect Binding Cover Settings]
Sets a paper size and paper source for the cover. If you are printing on the cover, set [Cover Printing].
[Content Page Settings]
Sets a paper size for the content pages.
[Finishing Settings]
123
Settings List
Specifies a finished size and adjustment method from [Specify By].

[Finishing Adjustments] Sheet
Adjusts the print positions of the content pages and cover, and the trimming angles and positions.
[Insert Watermark]
Superimposes and prints semi-transparent characters such as [TOP SECRET] or [DRAFT] over print data.
[Details]
Enables you to create new watermarks and edit existing watermarks.
☞ [Edit Watermark] Dialog Box
[Watermark List]
Displays a list of registered watermarks. When you select a watermark, the detailed settings of the
watermark are displayed in the preview and [Contents].
When you select a watermark and click [ ] (Move selected watermark up one) or [ ] (Move selected
watermark down one), you can change its place in the order of watermarks.
[Add]
Enables you to add a new watermark to [Watermark List].
[Edit]
Enables you to edit the selected watermark.
[ ] (Delete)
Deletes the selected watermark.
NOTE
● You can specify the watermark text by clicking [Add] or [Edit] → specifying the text in [Attributes] > [Text]. You
can specify the following content by combining "\" with specific characters.
\d: Date
\t: Time
\u: User name
\s: Computer name
\j: Job name
If you want to specify the character "\", enter "\\" in [Text].
[Add Frame]
Prints a border around the periphery of the page.
[Poster]
Enlarges the print data of one page and print it over multiple sheets of paper. When the output sheets are
joined together, they form a large print like a poster.
If you select [Custom], you can specify the number of rows and columns respectively.
[Details]
Enables you to set details such as the range of pages to print, printing with border lines, etc.
☞ [Poster Settings] Dialog Box
[Pages to Print]
Specifies the range of pages to be printed. You can also specify only some pages.
124
Settings List
If you have selected the number of rows and columns in [Custom], you can numerically specify the print
range and page numbers.
[Rotate sheets 90 degrees]
Rotates the page(s) specified in [Main] sheet > [Orientation] 90 degrees.
If you have selected [Auto], the pages will be oriented in the direction in which the print data is printed
larger.
[Print margin borders]
Prints borders with other sheets as a guide to paste sheets together.
[Set margins for cutting/pasting]
Sets cutting/pasting width and margins when printing.
The widths of margins are 20 mm (0.79 inches) for [Standard]. [Thin] and [Thick] reduce and increase the
widths by 10 mm (0.39 inches) respectively, based on the value of [Standard].
Selecting [Print marks for alignment] prints symbols that distinguish cutting and pasting.
[Mixed Sizes/Orientations]
Prints data in which the size and orientation differ from page to page.
[Details]
Enables you to set the combination of sizes and alignment method of pages.
[Header/Footer]
Enables you to attach a header or footer to the print data. You can set the position and format of the header
or footer.
If you are performing booklet printing or two-sided printing, you can also set the page number so that it is
printed in the same position on the front and back of the page.
[Overlay]
Performs overlay printing. You can also set creation of a form file to be used in overlay printing.
☞ [Overlay Settings] Dialog Box
[Processing Method]
Sets whether to perform overlay printing or create of a form file to be used in overlay printing. If you select
[Use Overlay Print], a form file stored in the device is used.
[Retrieve Form File Information]
Acquires the newest form file information.
[File List]
Displays a list of form files stored in the device. When performing overlay printing, select a form file to be
used from the list.
If you cannot acquire information from the device, the list is not displayed.
[Color] is applied when you click [Retrieve Form File Information].
[File Name]
Specifies a name for the newly created form file.
If you cannot select a form file from [File List], enter the name of the form file to be used here.
[Apply To]
Specifies which side to apply overlay printing to when performing two-sided printing.
[Copy Set Numbering]

Prints serial numbers on multiple copies of a document. For example, serial numbers are printed so that a "1"
is printed on the first copy of the document, "2" on the second, "3" on the third, etc.
125
Settings List
[Details]
Sets the print start number.
[Use secure printing function of device]

Uses the secure printing function of the device.
The functions to be used must be activated on the device side.
Related Topics
Attaching a Watermark(P. 70)
Printing a Large Poster over Multiple Pages(P. 71)
Overlapping Print Data on a Fixed Form(P. 75)
Perfect Binding(P. 93)
126
Settings List
[Paper Feed] Sheet
You can set the paper type and paper source.
[Select Paper By]

Sets whether to specify the paper to print on by paper source or by paper type.
[Paper Source]
Specifies the paper to print on by paper source. If you select [Auto], a paper source corresponding to the
output paper size is automatically selected.
[Paper Source Information]

Displays information about the paper set in the paper sources. You can also set a desired comment for each
paper source.
[Paper Name]
Specifies the paper source to be used when [Auto] is selected from [Paper Source]. In order to use this setting,
it is necessary to register the name of the paper corresponding to the paper source in the device beforehand,
and to acquire the device information.
[Paper Type]
Specifies the paper to print on by paper type.
[Settings]
Enables you to specify the paper type.
If you select [Auto], the document is printed on the paper type set in the device.
[Retrieve Paper Information]
Acquires information about paper set in the device and displays it in [Paper Type].
[Tab Details]
Enables you to set details for printing on the tab part when tab paper is specified.
[Paper Source for Transparencies]

Specifies the paper source for transparencies.
[Cover Sheets]
Sets whether to insert paper sheets between the transparencies. To print on the inserted sheets, select [Print
on cover sheets]. The same content that is printed on the transparencies will be printed on the inserted
sheets.
[Paper Source for Cover Sheets]/[Paper Type for Cover Sheets]/[Specify Cover Sheets By]
Sets the paper source and paper type for the sheets to be inserted when inserting sheets between
transparencies. When you can specify either the paper source or paper type, select [Specify Cover Sheets By].
[Insert Sheets]
Inserts sheets between specified pages.
[Settings]
Enables you to set details about the sheets to be inserted and their positions.
☞ [Sheet Insertion Settings] Dialog Box
127
Settings List
[Sheets to Insert]
Specifies the paper type of the sheets to be inserted.
[Paper Source]
Specifies the paper source of the sheets to be inserted.
[Inserted Sheets/Tab Paper]
Sets whether to print on the sheets to be inserted. If printing on the sheets, select which side to print on.
[Insertion Position]
Specifies the pages which inserts the sheets before.
[Paper Type for Tab Paper]
Enables you to specify the paper type of the tab paper to be inserted. You can also configure print settings
for the tab part.
[Carbon Copy]
Prints one copy each from two paper sources.
This function is useful when you want to print one copy of a document on high quality paper for the customer
and one copy on recycled paper to keep for yourself.
The function can be used when a setting other than [Auto] is selected from [Paper Source]. Specify the other
paper source in [Carbon Copy] > [Settings].
When this function is enabled, one copy is always printed from each specified paper source regardless of the
setting in [Main] sheet > [Copies].
Related Topics
Inserting Sheets Between Transparencies(P. 99)
Inserting Sheets(P. 100)
Inserting Tab Paper(P. 101)
Printing on Tab Paper(P. 102)
128
Settings List
[Finishing] Sheet
You can configure settings relating to finishing such as collating, stapling, etc.
Collate Group Offset
Rotate Hole Punch Staple
[Output Method]
Specifies a separating method when printing multiple copies.
[Collate]
Outputs the specified number of copies in page order.
[Group]
Outputs the specified number of copies with all pages having the same page number grouped together.
[Staple]
Staples the pages when outputting print data. Select staple position(s).
[On (Eco (Staple-Free))] crimps the paper without using staples.
The available staple positions vary depending on the output paper size, paper feed direction, and paper
source method.
[Hole Punch]
Outputs printed pages with holes for binding. This function can only be used when enabled at the device. The
type of punch holes you can select depends on the optional unit attached to the device.
[Offset]
Offsets each set of pages output.
[Specify Offset Interval: Every]

Outputs pages so that each specified number of pages is offset.
[Rotate]
Outputs each print job at a 90 degree angle relative to the one before and after it.
[Fold]
Specifies the type of fold when outputting pages folded into one of a variety of patterns.
129
Settings List
C-fold Z-fold Saddle fold Accordion Z-fold Double parallel fold
[Details]
Specifies the fold pattern when [C-fold], [Half fold], [Saddle fold (advanced)], [Accordion Z-fold], or [Double
parallel fold] is selected for the fold type.
NOTE
● If Z-fold and stapling are specified together, the fold direction of the Z-fold changes depending on the staple
location.
[Crease]
Makes a crease in printed paper so that it is easier to fold.
You can also select the paper to crease.
[Trim]
Trims and aligns the edges of the pages when creating a booklet by stapling the pages in the middle.
[Details]
Enables you to set the trim width and adjustment method.
[Output Destination]
Specifies a printed paper output destination.
[Details]
Enables you to set stacking details when [Stacker (stack area)] is selected to output to a large capacity stacker.
Related Topics
130
Settings List
[Quality] Sheet
You can set a print processing method to match the content of the print data.
[Content-Based Print]
Specifies an objective that matches the print data and sets a suitable print quality mode.
[Detailed Settings for Quality]

Enables you to set print quality details such as resolution, gradation, toner amount, etc.
☞ [Detailed Settings for Quality] Dialog Box
[Resolution]
Specifies the print resolution.
[Gradation]
Specifies the gradation method.
[High 2]: Uses a finer gradation than [High 1] to smooth gradations.
[Halftones (images)]/[Halftones (graphics)]/[Halftones (text)]
Specifies methods for representing halftones (areas between dark areas and light areas).
[Resolution]: Gives priority to resolution and prints contours smoothly.
[High resolution]: Increases the resolution of contours to more than [Resolution].
[Gradation]: Gives priority to gradation and prints gradations smoothly.
[Color tone]: Prints gradations more smoothly than [Gradation].
[Error diffusion]: Prints small characters and thin lines finely.
[Advanced smoothing]
Smooths the contours of text, lines, and images.
[Smooth 2]: Performs stronger smoothing processing than [Smooth 1].
[Sharpness]
Slightly adjusts the sharpness of the contours of characters and images arranged with each page.
[Sharpness (photo)]
Strengthens the contours of images, blurs. etc. when printing.
[Pure black processing]
Specifies a target object and prints sections other than white in black.
[Gray compensation]
Specifies a target object and prints black and gray data reliably in black and gray.
[Toner density adjustment]
Adjusts the toner density. In the details screen displayed when you specify [Custom settings] and click
[Details], you can adjust each color.
[Toner volume adjustment]/[Toner volume correction]
Adjusts the amount of toner to match the content of the print data.
[Gradation priority]: Prints data that includes large amounts of graphics and CG gradations.
[Text priority]: Prints data focusing on text.
[POP printing optimization]
Increases the amount of toner to print POP advertisements and images clearly.
To use this function, you must set both of the following beforehand.
- Disable [Main] sheet > [2-Sided Printing]
131
Settings List
- Click [Quality] sheet > [Matching Settings] → select [Device matching mode] in the [Matching Settings]
dialog box > [Matching Mode].
When enabling this function, it is recommended that the timing for low toner notifications is set to the [POP
Print] of the device. For details, refer to the manual of the device.
[Gradation smoothing]
Smoothly prints the amount of color change of gradations.
[Smooth 2]: Performs stronger smoothing processing than [Smooth 1].
[Image compression]
Adjusts the print data compression ratio when sending print data to the printer, and prints with priority given
to either image quality or print speed.
[Image compression optimization]
Sets an image compression method. You can select from an optimization method (switching between
reversible and irreversible) or a uniform compression method (no optimization). Compressing an image
using the optimization method suppresses JPEG block noise.
[Line control]
Improves reproduction of characters and lines.
[Resolution priority]: Gives priority to resolution.
[Gradation priority]: Gives priority to gradation.
[Prioritize printing of colored lines and text]
If colored lines or text are blurred or broken, they may print clearer if you enable this function.
If you have selected [Quality] sheet > [Content-Based Print] > [Line], this function is enabled by default.
[Color Adjustment]/[Grayscale Adjustment]

Enables you to adjust color, brightness, and contrast.
☞ [Color Adjustment]/[Grayscale Adjustment] Dialog Box
[Sample Type]
Specifies the type of image displayed in the sample preview.
If you select [Default], this is saved to print settings that match the type of data selected in [Elements to
Adjust] and the displayed image is also changed.
[Elements to Adjust]
Specifies an object as a color adjustment target.
[Apply to sample]
Applies the values set in [Saturation] and [Hue] sheets to the sample preview.
By switching the selection state, you can check how much the colors have changed.
[Color wheel]
Displays this as a guide when you adjust colors. This is displayed when the [Hue] sheet is selected.
[Saturation]/[Hue] Sheet
Enables you to adjust the saturation and hue of each color when printing in the [Color Adjustment] dialog
box. Adjust by dragging the slide bar or entering a numerical value.
[Adjust all colors using the same value]
Adjusts all colors simultaneously in the [Color Adjustment] dialog box.
[Brightness]/[Contrast]
Adjusts the brightness or contrast by dragging the slide bar or entering a numerical value.
[Matching Settings]
Enables you to set a matching operation for color adjustment.
☞ [Matching Settings] Dialog Box
[Matching Mode]
132
Settings List
Specifies the processing method for color matching.

[Matching Method]
Specifies what factor is prioritized when matching. Depending on the device, you can select factors to be
prioritized for each subject.
When you click [Retrieve Matching Method Information], you can retrieve information about the matching
methods registered in the device.
[Gamma]/[Gamma Adjustment]
Enables you to print with gamma adjustment.
[Two Colors Printing]

Prints in two colors, with the parts of the print data for which there is no color data printed in shades of black,
and the parts for which there is color data printed in shades of the specified color.
[Toner Save]/[Detailed Toner Save]

Saves toner by printing the print data with less toner.
In [Detailed Toner Save], printing is lightened in the order of [Mode 1], [Mode 2], and [Mode 3].
Related Topics
133
Settings List
[Covers] Sheet
You can add a front or back cover, use paper that differs from that of the content pages, and configure print
settings relating to covers.
[Configure front cover settings]/[Configure back cover settings]

Sets a front or back cover.
[Front Cover]/[Back Cover]

Specifies which side or sides of the front or back cover to print on.
[Paper Source]
Specifies a paper source.
NOTE
[Print banner page]

Inserts a page (banner page) containing the user name, job name, and time before printing the first page.
[Details]
Enables you to set the specifying method of the paper on which the banner page is printed (paper source
and/or paper type) and font size.
Related Topics
134
Settings List
[Support/Device] Sheet
You can configure the driver environment settings, device information settings, etc.
[View Settings]
Displays a list for checking the current settings.
[Edit Favorite Settings]

Enables you to edit the [Favorite Settings] list, and import or export it to be used on other computers.
☞ [Edit Favorite Settings] Dialog Box
[Favorite Settings]
Displays a list of registered favorite settings. The content of favorite settings selected from the list is
displayed in [Settings]. Settings that differ from standard settings are displayed in bold.
When you select favorite settings and click [ ] (Move selected favorite setting up one level) or [ ]
(Move selected favorite setting down one level), you can change its place in the order of favorite settings.
[Import]
Enables you to import the favorite settings saved as a file (*.profile) and add it to [Favorite Settings].
[Export]
Enables you to export the selected favorite settings as a file (*.profile).
[ ] (Delete)
Deletes the selected favorite settings.

[Comment]
Displays comments about selected favorite settings.
[Edit]
Enables you to edit the [Name], [Icon], and [Comment] of selected favorite settings.
[Troubleshooting]
Enables you to configure detailed driver operation settings for special printing or applications. Selecting an
item from [List of Settings] in the [Troubleshooting] dialog box displays a detailed explanation.
[Preferences]
Enables you to change the paper sizes displayed by the driver and the display language according to the
region you are using or your preferences, and initialize the settings of favorite settings etc. If you want to
change the display language, after selecting the language you want to use in [Language], close the print
settings screen then reopen it.
[Authentication Information Settings]

Enables you to manage printing by means of the department ID management function or the user
authentication function.
By clicking [Verify] on the displayed screen, you can check that the authentication information set in the device
and the entered content match.
135
Settings List
[User Name Settings]

Enables you to set a user name to be used for print jobs. The set user name is displayed on the control panel
of the device, and is used as the user name for headers or footers.
NOTE
● If you are using the user authentication function, the user name set for the user authentication function has
priority.
[Device Settings]
Enables you to configure device option settings and administrator settings.
NOTE
● When you click [Device Settings], after a confirmation screen asking whether you want to save the settings is
[Remaining Toner]
Displays the amount of remaining toner retrieved from the device.
[About]
Displays information about the driver version.
Related Topics
136
Settings List
[Device Settings]/[Administrator Settings] Sheet
You can check option settings, configure department ID management settings, and administrator settings
relating to the device.
NOTE
● If you return to the print settings screen, display it from the device icon in [Devices and Printers] or from the
print menu of a desktop app.
[Device Settings] Sheet
[Retrieve Device Information]

Acquires device information and applies it to the settings.
[Option List]
Displays in list form setting information about paper output options, paper source options, etc. attached to the
device.
If you want to set the option settings manually, after selecting an item, set the item displayed under [Option
List].
[Authentication Function]
Manages printing by means of the department ID management function or the user authentication function.
Click [Settings] and select the type of authentication function to use.
If you are using the department ID management function, selecting [Do not use Department ID Management
for B&W printing] enables black-and-white printing without authentication.
[Default User Name]

Enables you to set a default value of the user name to be used for print jobs. The set user name is displayed on
the control panel of the device, and is applied as the user name for headers or footers.
To set this item, [Administrator Settings] sheet > [Allow changes to user name] needs to be enabled.
[Device Function Settings]

Enables you to set the version of the controller firmware of the device. Which functions can be used by the
device depends on the version you set.
Controller firmware versions comprise function versions and platform versions. They can be viewed in a status
print of the device or a screen for confirming the structure.
For details on how to print the status print or confirm the structure of the device, refer to the manual of the
device.
NOTE
● Depending on the environment and settings, you may not be able to correctly acquire the controller
firmware version from the device.
If you can not correctly acquire it, the controller firmware version you have set will not be changed.
The latest versions supported by this driver are as follows.
- Function Version : [6.0]
- Platform Version : [308]
137
Settings List
Device version later than the above are not supported by this driver.
[Paper Source Information]

Displays information about the paper set in the paper sources. You can also set a desired comment for each
paper source.
[IP Address Settings]

Enables you to specify whether the IP address of the device whose information is to be acquired is
automatically detected or manually specified. If the IP address cannot be resolved, you can specify the IP
address to acquire the information of the device.
If you specify the IP address with this setting, it is not applied to the port for printing.
[About]
Displays information about the driver version.
[Administrator Settings] Sheet
[List of Settings]
Displays in list form the settings and their contents for the administrator of the device to manage default
settings.
[Change Administrator Settings]

Enables you to change user privileges and each of the settings in the [List of Settings] sheet.
Related Topics
138
Troubleshooting
Troubleshooting
Troubleshooting ............................................................................................................................................. 140
Cannot discover a device on a network ........................................................................................................... 141
Icon of the device is not displayed after installation ...................................................................................... 143
The Windows standard print settings screen is displayed ............................................................................. 144
Print settings return to their defaults after updating the driver .................................................................. 148
139
Troubleshooting
Troubleshooting
This explains solutions to common problems.

Icon of the device is not displayed after installation(P. 143)
Print settings return to their defaults after updating the driver(P. 148)
140
Troubleshooting
Cannot discover a device on a network
When installing with a network connection, the device may not be displayed in the [Printer List] of the installer.
Also, if you specify a network printer port during installation, the device may not be displayed in the shared
printer list.
If either of these happens, it could be due to a number of causes. Change settings as necessary by referring to
each "Remedy."
Cause 1.
The device settings are incorrect.
Remedy
Check whether the following have been set at the device. If they have not been set, change the settings or
install the appropriate driver.
● The IPv4 or IPv6 protocol settings have been enabled in [TCP/IP Settings].
● [Multicast Discovery Settings] has been enabled.
For network environments that use WSD, [Use WSD] has been enabled.
● [PDL Selection (Plug and Play)] and the page description language of the driver match.
For details about the setting method for the page description language (plug and play) function of the
device, refer to the manual of the device.
Cause 2.
The network settings of the operating system are incorrect.
Remedy
Check whether the necessary settings have been configured in the network settings of the operating system.
If they have not been set, change the settings according to the following procedure.
(1) Display [Network and Sharing Center] → check the network profile you are using in [View your active
networks].
You can display [Network and Sharing Center] as follows.
Select [Settings] > [Network & Internet] > [Ethernet] → click [Network and Sharing Center].
Click [Control Panel] > [Network and Internet] > [Network and Sharing Center].
(2) Click [Change advanced sharing settings].
(3) If [Network discovery] > [Turn off network discovery] is selected in the network profile checked in step (1)
(P. 141) , select [Turn on network discovery].
(4) Click [Save changes].
If the Administrator's password or confirmation is requested, enter the password or provide the
confirmation information.
141
Troubleshooting
Cause 3.
The operating system has been set up such that devices cannot be discovered.
Remedy
To display a device in the shared printer list, change the settings of the operating system according to the
following procedure.
(1) Click [Programs] > [Programs and Features] from the [Control Panel] of Windows.
(2) Click [Turn Windows features on or off] in the [Programs and Features] screen.
(3) Enable [SMB 1.0/CIFS File Sharing Support] in the [Windows Features] screen → click [OK].
You may need to restart the computer to enable the new setting.
For a server operating system, select [Manage] > [Add Roles and Features] from [Server Manager] and
enable [Features] > [SMB 1.0/CIFS File Sharing Support].
(4) After you have finished installing the driver, return the settings to their original values.
The above changes to the settings are only required for driver installation. It is recommended that you
return [SMB 1.0/CIFS File Sharing Support] to its original setting when driver installation is complete.
Cause 4.
The network environment is one in which devices cannot be discovered.
Remedy
● In a TCP/IP network environment, set it up so that the device you want to discover and the computer you are
using are on the same subnet.
● If the device you want to discover is connected to a network environment that does not use either TCP/IP or
WSD, install the driver by specifying a port or IP address.
Cause 5.
The driver corresponding to the discovered device is already installed.
Remedy
If you want to install a driver by discovering a device, uninstall the driver first, then discover it again.
Related Topics
142
Troubleshooting
Icon of the device is not displayed after installation
If the icon of the device is not displayed in [Devices and Printers] when installation is complete, this could be
due to a number of causes. Refer to each "Remedy" to have the icon of the device displayed.
Cause 1.
The screen has not been updated.
Remedy
Click [ ] (Refresh) in the address bar to update the screen to the latest status.
Cause 2.
The driver is being installed or the installation has not been correctly completed.
Remedy
Wait until the installation has been completed. If the icon of the driver is not displayed after you have waited
for some time, reinstall the driver.
143
Troubleshooting
The Windows standard print settings screen is

displayed
Even after you install the driver, the print settings screen of the driver may not be displayed and the Windows
standard print settings screen displayed instead. If this happens, a number of causes are possible.
Display the print settings screen of the driver by referring to the "Cause" and "Remedy" that explains each
Windows standard print settings screen displayed.
If displayed from the icon of the device in [Devices and Printers] or a desktop
app
The following screen is displayed from the icon of the device in [Devices and Printers] or when printing with a
desktop app.
Cause 1.
The driver has not been correctly installed in the client in a shared printer environment.
Remedy
Refer to the procedure for setting a computer as a shared printer client and install the driver.
144
Troubleshooting
Cause 2.
The driver was installed by the add printer function of Windows (by specifying an inf file or using
Windows Update).
Remedy
Install the driver using the installer.
If the environment does not enable installation using the installer, you will be able to use the Windows
standard print settings screen.
Cause 3.
There is the possibility of some sort of problem occurring while installing the printer driver.
Remedy
Uninstall the printer driver, then re-install it by following the correct procedure.
Cause 4.
The association of the driver with the print settings screen was broken when updating the driver using
Windows Update.
Remedy
Download the newest driver from the Canon web site (https://global.canon/) and update the driver using the
installer.
If displayed from a store app

The following screen is displayed when printing from a store app.
145
Troubleshooting
Cause 1.
You cannot connect to the Internet from the computer you are using.
Remedy
The functions required for printing with a store app are installed from the Windows store via the Internet.
Check that you can access the Windows store from the computer you are using, then reinstall the driver.
Cause 2.
The account you used to log onto Windows is not associated with a Microsoft account.
Remedy
Use a Microsoft account to install from the Windows store.
If the account you are using when logging onto Windows is an account other than a Microsoft account (a local
account or domain account), you need to associate it with a Microsoft account following the procedure below,
then install.
(1) Display the [Accounts] screen.
In Windows 10
Select [Settings] > [Accounts].
In Windows 8.1
146
Troubleshooting
Display the charm bar in the [Desktop] screen → select [ Settings] > [Change PC settings] > [Accounts].
(2) Set association with a Microsoft account.

In Windows 10
Select [Your info] > [Sign in with a Microsoft account instead].
In Windows 8.1
Select [Your account] > [Connect to a Microsoft account].
When you have finished configuring the settings according to the instructions on the screen, check that the
associated Microsoft account is displayed in the account information.
Cause 3.
The app is set so that the Windows standard print settings screen is displayed.
Remedy
If you are printing from a store app, set the app so that the print settings screen of the driver is displayed.
(1) Start the Canon Office Printer Utility.
In Windows 10
Select the Start menu > [Canon Office Printer Utility] from the list of apps.
Click [ ] at the bottom of the [Start] screen > [Canon Office Printer Utility] in the [Apps] screen.
(2) Display the [Options] screen of the Canon Office Printer Utility.
In Windows 10
Select the menu [ ] at the top of the app screen > [Settings] > [Options].
Display the charm bar in the [Desktop] screen → select [ Settings] > [Options].
(3) Disable [Settings for print settings screen] > [Always display in compatibility mode].
Related Topics
Installing Using Windows Update(P. 35)
Uninstalling the Driver(P. 40)
147
Troubleshooting
Print settings return to their defaults after updating

the driver
After updating an installed driver, if none of the print settings are carried over, and all of the print settings
return to their default settings, this may be due to the following cause. Address the problem according to the
"Remedy" content.
Cause
Windows specifications or changes in the driver due to additions or changes to functions.
Remedy
After acquiring the device information, change the print settings.
To acquire the device information, perform the procedure for enabling usage of the functions of the device.
Related Topics
148
SIL OPEN FONT LICENSE
This Font Software is licensed under the SIL Open Font License,
Version 1.1.
This license is copied below, and is also available with a FAQ at:
http://scripts.sil.org/OFL
-----------------------------------------------------------
SIL OPEN FONT LICENSE Version 1.1 - 26 February 2007
-----------------------------------------------------------
PREAMBLE
The goals of the Open Font License (OFL) are to stimulate worldwide
development of collaborative font projects, to support the font
creation efforts of academic and linguistic communities, and to
provide a free and open framework in which fonts may be shared and
improved in partnership with others.
The OFL allows the licensed fonts to be used, studied, modified and
redistributed freely as long as they are not sold by themselves. The
fonts, including any derivative works, can be bundled, embedded,
redistributed and/or sold with any software provided that any reserved
names are not used by derivative works. The fonts and derivatives,
however, cannot be released under any other type of license. The
requirement for fonts to remain under this license does not apply to
any document created using the fonts or their derivatives.
DEFINITIONS
"Font Software" refers to the set of files released by the Copyright
Holder(s) under this license and clearly marked as such. This may
include source files, build scripts and documentation.
"Reserved Font Name" refers to any names specified as such after the
copyright statement(s).
"Original Version" refers to the collection of Font Software

components as distributed by the Copyright Holder(s).
"Modified Version" refers to any derivative made by adding to,

deleting, or substituting -- in part or in whole -- any of the
components of the Original Version, by changing formats or by porting
the Font Software to a new environment.
"Author" refers to any designer, engineer, programmer, technical

writer or other person who contributed to the Font Software.
PERMISSION & CONDITIONS

Permission is hereby granted, free of charge, to any person obtaining
a copy of the Font Software, to use, study, copy, merge, embed,
modify, redistribute, and sell modified and unmodified copies of the
Font Software, subject to the following conditions:
149
SIL OPEN FONT LICENSE
1) Neither the Font Software nor any of its individual components, in

Original or Modified Versions, may be sold by itself.
2) Original or Modified Versions of the Font Software may be bundled,

redistributed and/or sold with any software, provided that each copy
contains the above copyright notice and this license. These can be
included either as stand-alone text files, human-readable headers or
in the appropriate machine-readable metadata fields within text or
binary files as long as those fields can be easily viewed by the user.
3) No Modified Version of the Font Software may use the Reserved Font
Name(s) unless explicit written permission is granted by the
corresponding Copyright Holder. This restriction only applies to the
primary font name as presented to the users.
4) The name(s) of the Copyright Holder(s) or the Author(s) of the Font

Software shall not be used to promote, endorse or advertise any
Modified Version, except to acknowledge the contribution(s) of the
Copyright Holder(s) and the Author(s) or with their explicit written
permission.
5) The Font Software, modified or unmodified, in part or in whole,

must be distributed entirely under this license, and must not be
distributed under any other license. The requirement for fonts to
remain under this license does not apply to any document created using
the Font Software.
TERMINATION
This license becomes null and void if any of the above conditions are
not met.
DISCLAIMER
THE FONT SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT
OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL THE
COPYRIGHT HOLDER BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM
OTHER DEALINGS IN THE FONT SOFTWARE.
150

PCL6 V4 PrinterDriver V712 UG EN PDF

Uploaded by

Copyright:

Available Formats

PCL6 V4 PrinterDriver V712 UG EN PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PCL6 V4 PrinterDriver V712 UG EN PDF

Uploaded by

Copyright:

Available Formats

Windows

UFR II/UFRII LT/LIPSLX/CARPS2/PCL6 V4 Printer Driver

USRMA-3204-03 2019-07 en Copyright CANON INC. 2019

About This Driver ........................................................................................................................................... 9

Before Use ......................................................................................................................................................... 12

Installing the Driver .................................................................................................................................. 14

Changing Settings to Match the Usage Environment .................................................. 44

Creating a Booklet ...................................................................................................................................... 86

Using Various Types of Paper ............................................................................................................ 97

Editing Favorite Settings ..................................................................................................................... 104

Coordinating with the Device Functions ............................................................................... 109

Settings List ................................................................................................................................................... 117

How to Use the Manual(P. 3)

How to Use the Manual

Notations Used in the Manual

This explains symbols and settings used in this manual.

Symbols Used in This Manual

The information in this document is subject to change without notice.

Copyright CANON INC. 2019

macOS and Safari are trademarks of Apple Inc.

About This Driver

About This Driver

Printing from a Desktop App

Printing from a Store App

Installing the Driver

Installing the Driver

This driver can be used with the following system environments.

Combinations of Driver and Operating System Display Languages

Supported Driver Languages

Scope of Guaranteed Operation

Language of operating Language of operating system

Installed with language matching the operating Guaranteed --

Installed with language not matching the Guaranteed*1 Not guaranteed*2

Changed to language not matching the operating Guaranteed*1 Not guaranteed*2

Notes and Warnings Regarding Installation

Take care of the following items when installing.

About the Readme File

Installing by Discovering Devices on a Network

3 Read the CANON SOFTWARE LICENSE AGREEMENT → click [Yes].

4 Select [Standard] → click [Next].

7 Select the device to install from [Printer List].

9 Change [Printer Name] if necessary → click [Next].

10 Check [List of Printers for Installation] → click [Start].

11 Check the installation complete message → click [Exit].

Installing by Specifying a Port or IP Address

As well as using an existing port, you can add a port.

3 Read the CANON SOFTWARE LICENSE AGREEMENT → click [Yes].

4 Select [Custom] → click [Next].

6 Select the device to install from [Printer List] → click [Next].

7 Set the port.

When adding a WSD port

When using an existing port

8 Change [Printer Name] if necessary → click [Next].

9 Check [List of Printers for Installation] → click [Start].

10 Check the installation complete message → click [Exit].

Installing by USB Connection

1 Turn off the device.

4 Read the CANON SOFTWARE LICENSE AGREEMENT → click [Yes].

5 Select [USB Connection] → click [Next].

Installed with language not matching the Guaranteed1 Not guaranteed2

Changed to language not matching the operating Guaranteed1 Not guaranteed2