7/04/2020

WIND02 v2-21
Detailed Wind Load Analysis per ASCE 7-10
Analysis by: R.M Company Name:
Description:

User Input Data Calculated Parameters

Structure Type Building Importance Factor 1
Basic Wind Speed (V) 77.7 mph Non-Hurricane, Hurricane (v=85-100 mph) & Alaska
Struc Category (I, II, III, or IV) II Table 6-2 Values
Exposure (B, C, or D) C Alpha = 9.500
Struc Nat Frequency (n1) 1 Hz zg = 900.000
Slope of Roof 3.0 :12
Slope of Roof (Theta) 14.0 Deg
Type of Roof Gabled
Kd (Directonality Factor) 0.85
Eave Height (Eht) 25.43 ft
Ridge Height (RHt) 37.73 ft
Mean Roof Height (Ht) 31.58 ft
Width Perp. To Wind Dir (B) 68.57 ft At = 0.105
Width Paral. To Wind Dir (L) 107.48 ft Bt = 1.000
Bm = 0.650
Calculated Parameters Cc = 0.200
Type of Structure l= 500.00 ft
Height/Least Horizontal Dim 0.46 Epsilon = 0.200
Flexible Structure No Zmin = 15.00 ft

Gust Factor Category I: Rigid Structures - Simplified Method

Gust1 For rigid structures (Nat Freq > 1 Hz) use 0.85 0.85
Gust Factor Category II: Rigid Structures - Complete Analysis
Zm 0.6 * Ht 18.95 ft
Izm Cc * (33/z)^0.167 0.2194
Lzm l*(zm/33)^Epsilon 447.49 ft
Q (1/(1+0.63*((B+Ht)/Lzm)^0.63))^0.5 0.8961
Gust2 0.925*((1+1.7*Izm*3.4*Q)/(1+1.7*3.4*Izm)) 0.8713
Gust Factor Summary
G Since this is not a flexible structure the lessor of Gust1 or Gust2 are used 0.85

Fig 6-5 Internal Pressure Coefficients for Buildings, Gcpi

Condition Gcpi
Max + Max -
Open Buildings 0.00 0.00
Partially Enclosed Buildings 0.55 -0.55
Enclosed Buildings 0.18 -0.18
Enclosed Buildings 0.18 -0.18

Project Classic LLC WIND Design

 7/04/2020

WIND02 v2-21
Detailed Wind Load Analysis per ASCE 7-10
6.5.12.2.1 Design Wind Pressure - Buildings of All Heights

Elev Kz Kzt qz Pressure (lb/ft^2)

Windward Wall* Leeward Wall Total Shear Moment
ft lb/ft^2 +GCpi -GCpi +GCpi -GCpi +/-Gcpi (Kip) (Kip-ft)
37.73 1.03 1.00 13.54 6.86 11.56 -6.63 -1.94 13.49 5.69 17.50
31.58 0.99 1.00 13.04 6.52 11.22 -6.63 -1.94 13.16 7.12 27.62
30 0.98 1.00 12.90 6.43 11.12 -6.63 -1.94 13.06 11.21 69.49
25.43 0.95 1.00 12.46 6.13 10.82 -6.63 -1.94 12.76 15.96 143.25
20 0.90 1.00 11.85 5.71 10.40 -6.63 -1.94 12.34 20.19 233.62
15 0.85 1.00 11.15 5.24 9.93 -6.63 -1.94 11.87 32.40 678.52
Note: 1) Positive forces act toward the face and Negative forces act away from the face.
Figure 6-6 - External Pressure Coefficients, Cp
Loads on Main Wind-Force Resisting Systems (Method 2)

Theta

B h
z

L L

Variable Formula Value Units

Kh 2.01*(Ht/zg)^(2/Alpha) 0.99
Kht Topographic factor (Fig 6-4) 1.00
Qh .00256*(V)^2*I*Kh*Kht*Kd 13.04 psf
Khcc Comp & Clad: Table 6-3 Case 1 0.99
Qhcc .00256*V^2*I*Khcc*Kht*Kd 13.04 psf

Wall Pressure Coefficients, Cp

Surface Cp
Windward Wall (See Figure 6.5.12.2.1 for Pressures) 0.8

Roof Pressure Coefficients, Cp

Roof Area (sq. ft.) -
Reduction Factor 1.00

Calculations for Wind Normal to 68.57 ft Face Cp Pressure (psf)

Additional Runs may be req'd for other wind directions +GCpi -GCpi
Leeward Walls (Wind Dir Normal to 68.57 ft wall) -0.39 -6.63 -1.94
Leeward Walls (Wind Dir Normal to 107.48 ft wall) -0.50 -7.89 -3.20
Side Walls -0.70 -10.11 -5.41
Roof - Wind Normal to Ridge (Theta>=10) - for Wind Normal to 68.57 ft face
Windward - Min Cp -0.58 -8.72 -4.03
Windward - Max Cp -0.06 -3.03 1.67
Leeward Normal to Ridge -0.47 -7.53 -2.83
Overhang Top (Windward) -0.58 -6.38 -6.38
Overhang Top (Leeward) -0.47 -5.18 -5.18
Overhang Bottom (Applicable on Windward only) 0.80 8.47 8.47
Roof - Wind Parallel to Ridge (All Theta) - for Wind Normal to 107.48 ft face
Dist from Windward Edge: 0 ft to 63.16 ft - Max Cp -0.18 -4.34 0.35
Dist from Windward Edge: 0 ft to 15.79 ft - Min Cp -0.90 -12.33 -7.63

Project Classic LLC WIND Design

 7/04/2020

WIND02 v2-21
Detailed Wind Load Analysis per ASCE 7-10
Dist from Windward Edge: 15.79 ft to 31.58 ft - Min Cp -0.90 -12.33 -7.63
Dist from Windward Edge: 31.58 ft to 63.16 ft - Min Cp -0.50 -7.89 -3.20
Dist from Windward Edge: > 63.16 ft -0.30 -5.67 -0.98
* Horizontal distance from windward edge

Figure 6-10 - External Pressure Coefficients, GCpf

Loads on Main Wind-Force Resisting Systems w/ Ht <= 60 ft

Kh = 2.01*(Ht/zg)^(2/Alpha) = 0.99
Kht = Topographic factor (Fig 6-2) = 1.00
Qh = 0.00256*(V)^2*ImpFac*Kh*Kht*Kd = 13.04
Theta = Angle of Roof = 14.0 Deg

Wind Pressures on Main Wind Force Resisting System

Surface GCpf +GCpi -GCpi qh Min P Max P
(psf) (psf) (psf)
1 0.48 0.18 -0.18 13.04 3.89 8.58
2 -0.69 0.18 -0.18 13.04 -11.35 -6.65
3 -0.44 0.18 -0.18 13.04 -8.04 -3.34
4 -0.37 0.18 -0.18 13.04 -7.23 -2.53
5 -0.45 0.18 -0.18 13.04 -8.22 -3.52
6 -0.45 0.18 -0.18 13.04 -8.22 -3.52
1E 0.72 0.18 -0.18 13.04 7.10 11.79
2E -1.07 0.18 -0.18 13.04 -16.31 -11.61
3E -0.63 0.18 -0.18 13.04 -10.51 -5.82
4E -0.56 0.18 -0.18 13.04 -9.60 -4.90
* p = qh * (GCpf - GCpi)

Project Classic LLC WIND Design