Schedule of Rates 2018 For Kalpeni W.E.F 01.11.2018

1 afc91d2399f7e2e8d231dbea2d348e99
SCHEDULE OF RATES
2018 FOR KALPENI
W.E.F 01.11.2018
Sd/- Sd/-
Prepared by Checked by
Shri. K.Koyakidave Shri. Mohammed Nazeem
( Head Draughtsman ) Assiastant Engineer
( LPWD Kavaratti )
Sd/- Sd/-
Shri. M.K.Abdul Salam Shri. Arun Jadhav
Executive Engineer Executive Engineer
( LPWD Kavaratti ) ( Smart Cell Kavaratti )
Sd/-
Shri.Mohammed Kudage
(Superintending Engineer)
afc91d2399f7e2e8d231dbea2d348e99
Carriage of Materials
By Manual Labour including loading, unloading and
stacking for lead less than 0.5 KM
Cost per
unit
Unit cost for 1st cost
ofRates 50 metres foraddl. 50
m or part
thereof
beyond1st5
0 m upto
0.5 km
S. No Materials
1 Lime, mooram building 1 cum 177.3 38.41
rubbish
2 Earth 1 cum 221.62 48.01
3 Manure or sludge 1 cum 192.71 41.75
4 Excavated rock 1 cum 354.59 76.82
5 Sand, stone aggregate 1 cum 177.3 48.01
below 40 mm nominal
size
6 Stone aggregate 40 mm 1 cum 239.59 51.91
nominal size and above
7 Soling stone 1 cum 260.73 56.49
8 Bricks 1000 Nos 413.69 89.62
9 Brick Tiles, Allahabad 1000 Nos 258.56 56.01

roofing tiles (Flat or
round)
10 Stone blocks, G.I., 1 tonne 161.00 23.63
C.I.pipes below 100 mm
dia and other heavy
materials
11 Cement 1 cum 127.71 18.74
12 Steel 1 tonne 274.30 40.25
13 Timber 1 cum 176.33 25.88
14 S.W./ PVC/UPVC pipe
15 100 mm dia 100 m 322.28 47.29
16 150 mm dia 100 m 529.76 77.74
17 200 mm dia 100 m 741.34 108.78
ANALYSIS OF RATES FOR TRANSPORTATION OF MATERILAS FROM STORE YARD TO WORK SITE AT KALPENI
Vide Ref FNo.Fno.10/3/4-AEK/491/dated.14.6.2018
I Cement
Rate for per tonne 400.00 /Tonne
II River sand
Rate for per Cum (1.6 Mt/cum 750.00 750.00 Cum
III Granite Chips per Mt
Rate for per Cum ( 1.8 Mt/cum) 750.00 750.00 Cum
IV Steel
Rate for per Mt 1000.00 1000.00 /Tonne
V Bricks ( 0.75/Each)
Rate for per 1000 Nos (2.5 Mt) 300*2.5 750.00 750.00 1000Nos
Vi Timber per Mt
Rate for per Cum ( 0.8 Mt/Cum) 1000.00 1000.00 Cum
Vi Granite boulders
Rate for per Cum ( 2.8 Mt/cum) 750.00 750.00 Cum
2
ANALYSIS OF RATES FOR TRANSPORTATION OF MATERILAS FROM STORE YARD TO WORK SITE AT KALPENI
SLNo Materials Total Unit
1 Cement 400.00 /Mt
2 Sand 750.00 /Cum
3 Granite chips 750.00 /Cum
4 Steel 1000.00 /Mt
5 Bricks 750.00 /1000 Nos
6 Timber 1000.00 /Cum
7 Granite boulders 750.00 Cum
SCHEDULE OF RATES 2018 AT KALPENI

BASIC RATE
Transportation of Materials Unit Rate
1 Cement Mt 400.00
2 River sand/Metal sand Cum 750.00
3 Granite chips Cum 750.00
4 Steel Mt 1000.00
5 Bricks 1000 Nos 750.00
6 Timber Cum 1000.00
7 Granite boulders Cum 750.00
Labour Rate
8 Paintor,Fitter& Blacksmith Each 800.00
9 Mason,Carpentor, 1 st class Each 800.00
Mason,Carpentor, Black smith, Fitter 2 nd class ,glazer and
10
Mistry Each 750.00
11 Beldar,Coolie,Bhisti,Bhandani,Chowkidar,Mate Each 700.00
Materials Rate
12 Cement ( Ag No.50/KLP/2016-17) Bag 444.00 8880
13 Granite chips ( Ag No.56/KLP/16-17) Cum 4440.00
14 River sand Cum 4444.00
15 Bricks ( Ag No.17/KLP/15-16) Each 17.00
16 Granite boulders ( Ag No.80/KLP/15-16) Cum 3800.00
17 Steel ( Ag No.50/KLP/2016-17) Kg 53.00 5300
18 Metal sand ( Ag No.11/KLP/16-17) Cum 4190.00
19 Granite baby Chips ( Ag. No 70/EE Kvt/2014-15 ) Cum 4207.00
20 Granite powder ( Ag.No 59/EE Kvt/2014-15 ) Cum 3999.00
21 C.C. block 40x20x15Cms( Ag No.05/KLP/15-16) each 78.80
22 Deisal litr 75.00
21 Timber Scantlings (Aggr.No.82/KLP/2014-15) Cum 59400.00
22 Timber Planks Cum 59400.00
23 Timber Reeper Cum 59400.00
24 Red Mud ( Ag No.18/KLP/16-17) Cum 3290.00
25 Mixer (DSR 2016) Each 800.00
26 Vibrator (DSR 2016 ) Each 350.00
27 Hydraulic excavator with driver and fuel (DSR 2016) Day 8000.00
28 Hire running charges of loader (DSR 2016) Day 5000.00
Hire running charges of tipper (DSR 2016) Day 1700.00
29 Timber Planks ( Kail wood for centring & shuttering) Cum 43968.75
30 Wall form panel 1250x500mm Each 2296.88
31 Corner angle 45x454x5mm 1.50m long Each 630.00
32 100mm channel shoulders 2.5 mlong Each 2493.75
33 Double clip ( bridgre clip ) Each 196.88
34 Single clip Each 170.63
35 MS Tube 40 mm Mtr 496.13
36 Adjustable span-ESOSI (2.35-3.40m) Each 2985.94
37 Adjustable telescopic prop 3mm (2.02-3.75m) Each 2067.19
38 Beam clamp 300 -380 mm ( 450-1070 mm ) Each set 853.13
39 Wall form panel 1250x400mm Each 2034.38
40 Corner angle 2.50 m long Each 715.31
41 Column clamp (450-1070 mm) Each 1949.06
42 Prop.2m (2.0-3.5) Each 1345.31
43 Safeda ballies 125 mm dia Mtr 85.31
44 Carriage of stone aggregate Cum 177.30
45 Carriage of Coarse sand Cum 177.30
46 Carriage of Timber Cum 176.33
47 Carriage of steel Mt 274.30
48 Carriage of cement Mt 127.71

49 Carriage of bricks 1000 Nos 258.56
50 Carriage of A.C/G.Alum sheet and accessories Mt 161.00
51 Trough and bond stone Each 25.59
52 M.S butt hinges 100x58x1.90mm Each 78.72
53 M.S butt hinges 50x37x1.50mm Each 35.78
54 M.S screw 40 mm Each 1.07
55 M.S screw 20 mm Each 0.72
56 Float glass sheet 4 mm thick Sqm 543.88
Black board construction flush door with teak wood ply on
57
both face 35 mm thick Sqm 3005.63
58 Stainless butt hinges 100x60x2.5mm IS 12817 Each 150.28
59 Stainless steel screws 40 mm Each 3.94
60 M.S flat 40x5mm 0.40m long Qntl 9187.50
61 Coir veneer board 18 mm thick sqm 1789.06
62 Coir veneer board 6 mm thick sqm 930.31
63 Rawl plug 50 mm Each 17.18
64 Teak wood second class scantlings Cum 108281.25
65 Teak wood second class planks Cum 140000.00
66 C.P brass curtain road 20 mm dia Mtr 493.78
67 C.P.brass bracket Each 21.47
68 Nickel plate M.S pipe 20 mm dia Mtr 128.81
69 Nickel plate M.S bracket Each 18.61
70 Alu.sliding door bolt 300x16mm Each 372.13
74 Alu.Tower bolt 225x10mm Each 178.91
78 Alu.handle 125 mm Each 121.66
81 Alu.hooks &eyes 200 mm Each 107.34
82 Alu.hooks &eyes 150 mm Each 97.33
83 Brass screws 25 mm Each 1.79
84 Brass tower bolt 250x10 mm Each 357.81
88 Brass handle 125 mm Each 264.78
91 Brass door latch 300x16x5 mm Each 930.31
92 Brass door latch 250x16x5 mm Each 824.40
93 Brass casement stayes 300 mm Each 264.78
96 Brass cup board lack 75 mm Each 160.30
97 Brass door stopper 75 mm Each 100.19
98 Cupboard knob Each 60.11
99 Mortice lock 6 levers 100 mm Each 1216.56
100 Brass hudraulic door closer Each 1574.38
101 24 mm thick factory made PVC door shutter Sqm 3291.88
102 30 mm thick factory made PVC door shutter Sqm 3506.56
103 25 mm thick factory made PVCflush shutter Sqm 3184.53
104 Factory made PVC door frame 50x47x5 mm Mtr 551.03
Factory made glass reinforced plastic door frame 90x45xmm

105
i/c carriage Mtr 593.97
30 mm thick factory made glass fiber reinforced plasticpanel
106
door shutter i/c carriage Sqm 2812.41
107 Structural steel such as tees,angles,channels & R.S joist Qntl 9843.75
108 Flats exceeding 10 mm in thickness Qntl 8531.25
109 Flats upto10 mm in thickness Qntl 8531.25
110 Miled steel plates Qntl 10631.25
111 Bolts and nuts 300 mm and above length Qntl 11241.56
112 Pulley 40 mm dia Each 91.88
113 Rolling shutter of 80x1.25 mm lath Sqm 2034.38
116 Top cover 1.25mm thick Mtr 892.50
117 Top cover 1.20mm thick Mtr 479.06
118 Top cover 090mm thick Mtr 426.56
119 Coil type spring Each 380.63
120 Coil type spring 0.90 mm Each 216.56
121 Ball bearing Each 507.94
122 Miled steel tubes hot finished welded type Kg 150.94
123 Miled steel tubes hot finished seamless type Kg 170.63
124 Miled steel tubes electric resistant Kg 203.44
125 Welding by gas plant cms 4.27
126 M.S holding down bolt 1200 mm long Qntl 11241.56
127 G.I Pipe Mtr 328.13
128 Ceramic glazed wall tiles Sqm 586.81
129 Ceramic glazed floor tiles 300x300 mm Sqm 708.47
130 Vitrified floor tiles 50x50 cm Sqm 1350.00
131 Galvanised steel corrugated sheets Qntl 9384.38
132 G.I Steel bolt & nuts 6 mm dia and 25 mm long 10 Nos 39.38
133 G.I,J or L hooks 8 mm 10 Nos 140.44
134 G.I Limpet washer 100 Nos 53.13
135 Bitumen washer 100 Nos 44.37
136 G.I plain sheet 0.80 mm thick Qntl 8859.38
137 G.I plain washers 100 Nos 49.88
138 G.I Seam bolt&nuts each 45.50
139 Press clay tiles 20 mm thick 250x250 mm size 1000 Nos 19228.13
140 Carriage of tiles 1000 Nos 170.63
141 water proofing materials Kg 42.94
142 Natural colour insulating board 12 mm thick Sqm 536.72
143 White face insulating board 12 mm thick Sqm 651.22
144 Particle board medium density ( Grade.I) 12 mm thick Sqm 586.81
145 12.5 mm thick tapered edge gypsum plain board Sqm 300.56
146 Galvanise steel ceiling section ( size 80x26x50 mm ) Mtr 68.25
1471 Galvanise steel Perimeter channel (size20x27x30x0.5mm)
Mtr 52.50
148 Galvanise steel intermediate channel (size15x45x15x0.90mm)
Mtr 63.00
Galvanise steel angle hanger( ceiling angle )
149
(size25x10x0.5mm) Mtr 34.13
Galvanise steel connecting clip ( 2.64 mm dia and 230 mm long
150
GI wire ) Mtr 45.94
151 Galvanise steel soffit cleat ( size 27x37x25x0.60 mm ) Each 8.01
152 All drive screws ( for gypsum board ) 100 Nos 98.47
153 Joint filler Kg 39.36
154 Joint finisher Kg 41.79
155 Joint tape roll Roll 241.88
156 Dash fastner 12 mm dia 40 mm long with6 mm dia bolt Each 77.44
157 12.5 mm thick tapered edge gypsum fire resistant board Sqm 413.99
158 12.5 mm thick tapered edge gypsum moisture resistant board
Sqm 480.47
159 Press clay Mangalore tiles 20 mm thick Each 19.23
160 Press clay Mangalore ridge tiles 20 mm thick Each 49.59
161 Aluminium roofing sheet 0.56 mm thick sqm 975.00
162 Hips / ridges of Aluminium sgeet 1.22 mtrs length each 780.00
163 O.P Pipe 15 mmdia Mtr 65.84
169 P.V.C Pipe 110 mmdia ( 6 kg/sqcms) Mtr 293.41
177 C.P Brass bib cock 15 mm Each 317.74
178 C.P Brass bib cock 20 mm Each 422.22
179 C.P Brass stop cock 15 mm Each 317.74
180 C.P Brass stop cock 20 mm Each 422.22
181 G.M Full way valve 25 mm Each 608.28
185 Ball valve ( brass ) 15 mm Each 253.33
188 C.P Shower vrose 15 to 20 mm inlet 100 mm dia Each 322.03
189 C.P Shower vrose 15 to 20 mm inlet 150 mm dia Each 372.13
Polyethylene water storage tank with cover and suitable
190
locking arrangement per litre 10.16
191 C.P brass bib cock IS :8931 15 mm Each 565.34
192 C.P brass long nose bib cock 15 mm Each 593.97
193 C.P brass stop cock ( concealed ) 15 mm Each 608.28
194 C.P brass angle valve 15 mm Each 679.84
195 PTMT bib cock 15 mm Each 200.38
196 PTMT bib cock with flange ( fancy ) 15 mm Each 254.76
197 PTMT bib cock long body with flange 15 mm Each 283.39
198 PTMT stop cock ( male thread ) 15 mm Each 178.91
199 PTMT stop cock 20mm Each 246.18
200 PTMT push cock 15 mm each 153.14
201 Chlorinated Polyvinyl-chloride (CPVC) pipe 15 mm OD Mtr 92.32
207 White solid plastic seat and lid Each 551.03
208 White vitrous china pedesatal type W.C pan Each 1323.91
209 10 liters low lvel C.I flushing cistern with fittings Each 1223.72
210 Vitrous china flat back wash basin 550x400 mm Each 923.16
211 C.P brass pillar tap 15 mm Each 307.72
212 C.P brass waste coupling 32 mm Each 107.34
213 C.I.M.S brackets Each 97.33

214 C.P brass ccoupling 40 mm Each 48.66
215 C.P brass wate 40 mm Each 109.49
216 White vitrous china kitchen sink 600x450x250mm Each 2490.38
Stainless steel Kitchen sink with drain board bowl depth 250
217
mm (510x1040x250mm ) Each 7528.38
218 White vitrous china laboratory sink 450x300x150mm Each 1409.78
219 C.P brass tap 40 mm Each 222.20
220 C.P brass union Each 308.43
221 Mirror superio glass 600x450 mm each 525.27
222 Hard board 6 mm thick Sqm 250.47
223 Wooden plug Each 25.76
224 C.P brass towel rail 600x20 mm Each 450.84
225 PTMT liquid soap container 400 ml capacity Each 256.62
226 Vitrous china toilet paper holder Each 208.18
227 P.V.C soil waste and vent pipe 1.83 mtr long 100 mm Each 397.89
228 P.V.C soil waste and vent pipe 1.83 mtr long 75 mm Each 312.01
229 Stainless steel toilet paper holder Hindware F840008 Each 1280.97
230 Aluminium T or L sections Kg 551.03
231 C.P brass s.s screws 20 mm 100 Nos 200.38
232 Anodising 15 microns on aluminum sections Kg 68.70
233 Powder coating 50 microns on aluminium sections Kg 111.64
234 Aluminum hinges 100x75x4 mm Each 88.74
Prelaminated particle boardwith one side decorative and other
235 side balancing lamination Grade.I type.II,confirming to IS
12823 ,12 mm thick Sqm 1242.33
Prelaminated particle boardwith both side decorative
236
lamination Grade.I type.II,confirming to IS 12823 12mm Sqm 1273.81
237 Neoprene/ EDPM rubber gasket Mtr 50.09
238 Float glass panes 4 mm thick Sqm 543.88
239 Float glass panes 5.5 mm thick Sqm 784.33
240 Float glass panes 8 mm thick Sqm 1166.47
241 Toughened glass 12 mm thickness Sqm 2800.00
Double action hydraulic floor spring with stainless steel cover
242
plate Each 2647.81
243 Double action hydraulic floor spring with brass cover plate
Each 3077.19
244 Silicon sealant cartridge 536.72
245 Masking tape Mtr 2.65
Brass 100 mm mortice latch and lockwith 6 levers with out pair
246
of handles Each 500.94
247 Aluiminium casement window fastner ( Anodided AC 15) Each 78.72
248 Aluminium round shape handle ( powder coated ) Each 97.33
249 Brass door stopper 150mm Each 281.96
250 S.S Screws 30x4 mm 100 nos 52.00
251 S.S Screws 25x4 mm 100 nos 43.00
252 Brass screws 40 mm 100 Nos 247.00
253 Brass hard drawn hooks and eyes 250 mm 10 Nos 1080.59
254 Brass hard drawn hooks and eyes 200 mm 10 Nos 1037.66
255 C.P brass butt higes 100x70x4 mm 10 Nos 1080.59
256 C.P brass butt higes 75x65x4 mm 10 Nos 1624.47
257 White cement Qntl 3291.88
258 Dry distember Kg 69.42
259 Oil bound washable distemper / arcylic distemper Kg 78.72
260 Water thinnable cement primer litre 134.54
261 Water proofing cement paint Kg 68.70
262 Textured exterior paint litre 383.58
263 Exterior primer Kg 52.00
264 Arcylic exterior paint litre 307.72

265 Multi surface paint litre 551.03
266 Special primer (C.W) litre 157.44
267 Metal primer ( U.G ) litre 211.83
268 Pink primer for wood litre 138.12
269 Red oxide Zinc chromate primer litre 138.12
270 Spirit litre 84.50
271 Shellac Kg 350.66
272 Wall putty Kg 35.00
273 Black japan paint litre 160.30
274 Roofing paint for iron sheets in red colour litre 193.22
275 Oil type wood preservative litre 124.52
276 Plastic emulsion paint litre 279.09
277 Synthetic enamel paint litre 223.28
278 Aluminum paint litre 193.22
279 Acid proof paint litre 182.48
280 C.P brass chain with 32 mm dia rubber plug Each 40.79
281 C.P brass chain with 40 mm dia rubber plug Each 45.08
282 Premium Arcylic exterior paint litre 400.75
283 Superior spar varnish litre 221.84
Raj nagar Plain white marble 18 mm thick ( tablr rubbed and
284
polish) slab area up to 0.50 sqm Sqm 1123.53
Raj nagar Plain white marble 18 mm thick ( tablr rubbed and
285
polish) slab area more than 0.50 sqm Sqm 1209.41
Granite of any colour 18 mm thick ( slab area up to 0.50
286
sqm Sqm 2862.50
Granite of any colour, 18 mm thick ( slab area above 0.50
287
sqm Sqm 2934.06
288 8 mm thick marble tiles ( polished)Raj nagar Sqm 589.68
289 8 mm thick granite stone tiles ( mirror polished of all shades
Sqm 1162.18
290 Concrete Jali 50 mm thick Sqm 612.58
293 stand jally ( round) Each 54.39
294 Top and Bottom rail Each 357.81
295 charupadi Each 25.76
296 Precast chequered cement tiles 22 mm thick Sqm 399.50
297 Black colour dark shade pigment Kg 80.80
298 Acid and alkali resistant tiles 300x300mm Sqm 829.92
299 Acid proof cement tonne 11866.40
300 Interlocking CC paver block 60 mm thick Sqm 700.00
301 Bitumen blow type tonne 64480.00
302 Galvanized steel barbed wire Qntl 6760.00
303 Trunl buckle & straple tonne 97.94
304 Link mesh 50x50 mm made of G.I wire dia 4mm Sqm 407.4
Link mesh 50x50 mm made of ,PVC coated to outer dia 5 mm
305 Sqm 503.70
306 Wooden cleat each 21.75
307 Screws & washers cent 375.00
308 Orissssa type W.C pan 580 mm size each 1014.00
P.V.C flushing Cistern 10 l;iters (low level )white with
309
fittings,accessories and flush pipe each 832.00
310 100 mm S.C.I trap with vent heel each 410.00
311 Vitreous china lipped front urinal each 598.00
312 P.V.C automatic flushing cistern 5 liter capacity each 637.00
G.I Flush pipe and C.P brass spreader with connecting pipe
313
single lipped each 605.00
314
two lipped urinals each 1365.00
315
three lipped urinals each 1625.00
316 four lipped urinals each 2470.00
317 Cast iron trap 100 mm outlet 100 mm inlet each 566.00
Air cpmpressor 250 cfm with two leads for pneumatic
318
cutters/hammers ( SDR 2013 ) Day 1900.00
319 Tractor with trolly ( DSR 2013 ) Day 1500.00
320 Joint cutting machine with 2-3 blades ( DSR 2013 ) Day 1000.00
321 Hand Grinder for mirror polish Day 230.00
322 Floor Ginder machinr ( Granite ) Day 350.00
323 Spunyarn Kg 52.00
324 Lumsum ( DSR 2013) LS 1.73
Stainless steel wire guage (grade 304) aperture 1.4mm and
325
0.50mm dia wire Sqm 1176.00
326 Aluminium tee chanel ( heavy duty) with rollers and stop end
Mtr 90.00
327 Auto hinges Each 150.00
328 Screws 50 mm Each 5.00
329 Brass cupboard lock 6 lever 40 mm size Each 220.00
330 Telescopic drawer channel 300 mm long Each 400.00
331 18 mm thick MDF board laminated Sqm 1000.00
332 Aluminium maruthi handle 125mm Each 150.00
333 Aluminium rod 32mm dia Mtr 226.39
334 Aluminium brackets Each 6.50
335 Miled steel rivets Qntl 6240.00
336 Stainless steel grade hollow section Kg 455.00
337 Stainless steel bolt Kg 156.00
338 Chequarred cement concrete tiles 22mm thick Sqm 705.00
339 Vitrified floor tiles 500x500 cm (kajaria equivalent) Sqm 1599.00
343 Perpaint G.I roofing sheet 0.45mm thick Sqm 587.50
344 Perpaint G.I ridge sheet 0.45mm thick Mtr 159.79
345 Bamboo board 4mm thick Sqm 408.00
White vitrous china pedastal type W.C pan with white soild
plastic seat and lid with CP brass hinges and rubber buffers
346 complete inclluding flushing cistern with fittings size
775x370x640mm trap distance S 200/P 180 ( Jaquar modal SLS
WHT - 0208/0208P or equivalent) each 11037.00
White vitrous china wash basin 550x605x475mm with half
347
pedastal (Jaquar modal FNS WHT - 1503 or equivalent)
each 8433.10
Mirror superio glass 700x500 mm ( cera modal no.5561 size
348
700x500mm) each 843.00
Orissssa type W.C pan 580 x440mm mm size ( cera jhonson or
349
equivalent) each 5850.00
350 Brass scrwes 30mm 100 nos 195.00
351 Zink chromate yellow primer litre 115.00
352 Putty birla white or equivalent Kg 15.00
353 Putty nerolac white or equivalent Kg 13.00
354 Arcylic exterior paint ( nerolac premier or equivalent) litre 193.70
355 Multi surface paint ( Berger, birla or equivalnt) litre 780.00
356 Multisurface paint ( Tefflon coat Asian or equivalent) litre 643.50
357 Metalic paint litre 1950.00

358 Non metalic paint litre 1350.00
359 Base coat of metalic and non metalic paint litre 950.00
360 Tools of metalic & non metalic paint set 800.00
361 metal design paint litre 1001.00
362 Non- metalic design paint litre 715.00
363 Arcylic emulsion voc contents less than 50gm litre 423.80
364 Epoxy paint litre 615.00
365 Melamin mat ( polish for wooden floor) litre 403.00
366 Poly urthene mat litre 851.50
367 straining bolts each 79.50
368 Carriage of stone / CC blocks etc Cum 277.96
369 Link mesh 25x25 mm made of G.I wire dia 8 guage Sqm 611.00
370 Premix 1:3 ( Ag No 12/EE/Amini/2014-15) Bag 384.50 7690
371 Premix 1:6 ( Ag No.18/EE/Amini/2014-15) Bag 379.00 7580
372 Turn buckle each 15.3
P.V.C low level flushing cistern 10 liters (white) with fittings
373
,accessories and flush pipe each 1223.72
374 Stailess steel A ISI 304 labour room sink each 43550.00
375 PVC Ceiling board Sqm 225.96
376 Chicken mesh Sqm 47.22
377 M.S Welded mesh 50x50mm Sqm 51.25
Steel glazed door,window,ventilator,all members viz
378
F7D,F4B,K11 and K12B etc.. Kg 83.20
379 Press steel door frame ( mild steel sheet 1.60 mm) profile "B"
Mtr 368.00
380 Single socket rain water pipe 75 mm dia Mtr 93.60
381 Single socket rain water pipe 100 mm dia Mtr 175.50
382 PVC half round eaves gutter 100 mm dia ( 10kg/sqcm) Mtr 136.67
Non Asbestos high impact Polypropylene reinforced cement 6
385
mm corrugated sheet (IS 14871) Mtr 979.16
Non Asbestos high impact Polypropylene reinforced cement 6
386
mm ridges sheet Mtr 475.00
387 PVC ball valve 63 mm each 312.00
391 PTMT grating 100 mm ( circular type ) each 70.00
392 PTMT grating 125 mm ( circular type ) each 84.00
393 PTMT grating 150 mm (square type ) each 185.00
394 Health faucset 15mm each 550.00
395 C.P brass angle cock 20 mm each 350.00
396 C.P brass sink cock 20 mm each 850.00
397
PTMT angle stop cock 15mm ( weighing not less than 85 gms) each 250.00
398 PTMT swiwelling shower 15 mm each 180.00
PTMT soap dish holder 138x102x75 mm ( weighing not less
399
than 106 gms ) each 165.00
400 C.P wall mixure 15 mm each 4176.00
Stainless steel kitchen sink with out drain board bowl deth
401
450x400x250 mm each 1075.00
402 100 mm PVC. Grating for gully or Nahani trap each 45.00
403 25 mmMosquito proof coupling of the approved each 60.00
600x120x5 mm glass shelf with anodised aluminium angle
404 frame C.P. brass brackets & guard rail of standard size
each 400.00
405 C.P. brass toilet holder of standard size each 325.00

406 Vitreous china toilet holder of standard size each 250.00
SH:-1. MORTARS ( M Sand )

Labour
Item No Specification Unit Rate
Rate
1.6 Cement mortar 1:1 Cum 14093.66 1948.57
1.7 Cement mortar 1:2 Cum 12070.83 1975
SH:-1A .MORTARS With Premix
SH:-2.EARTH WORK
Labour
Rate
2.1 Surface dressing of the ground including removing vegitation
and in equalities not exceeding 15cm deep and disposal of Sqm 26.51 26.51
rubbish lead up to 50 metres and lift up to 1.5 metres
2.2 Earth work in excavation by mechanical means (Hydraulic
excavator)/ manual means over areas (exceeding 30cm in depth.
1.5m in width as well as 10 sqm on plan) including disposal of
excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to
be levelled and neatly dressed.
2.2.1 All kinds of soil Cum 445.60 445.60
2.3
Earth work in excavation/ by mechanical means (Hydraulic
Excavator)/ manual means over areas (exceeding 30 cm in depth,
1.5m in width as well as-10 sqm on plan) including disposal of
excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth
to be levelled and neatly dressed.
2.3.1 Ordinary rock Cum 628.80 628.80
2.4 Earth work in excavation by mechanical means (Hydraulic
Excavator )/ manual means in foundation trenches or drains (not
exceeding 1.5 m in width or 10 sqm on plan) including dressing of
sides and ramming of bottoms, lift upto 1.5 m, including getting out
the excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m
All kinds of soil. Cum 275.35 275.35

2.4.1 Extra for every additional lift of 1.5 m or part thereof in.
All kind of soil Cum 104.55 104.55
Up to 1.50 mtr to 3.00 mtr ( A+B) Cum 379.90 379.90
Up to 3.00 mtr to 4.50 mtr (B+C) Cum 484.45 484.45
Up to 4.50 mtr to 6.00 mtr ( B+D) Cum 589.00 589.00
2.4.2 Extra for every additional lift of 1.5 m or part thereof in.
Ordinary or hard rock. Cum 187.30 187.30
Up to 1.50 mtr to 3.00 mtr ( A+B) Cum 462.65 462.65
Up to 3.00 mtr to 4.50 mtr (B+C) Cum 649.95 649.95
Up to 4.50 mtr to 6.00 mtr ( B+D) Cum 837.25 837.25
2.5 Earth work in excavation by manual means in foundation trenches
or drains (not exceeding 1.5m in width or 10 Sq.m on plan)
including dressing of sides and ramming of bottoms, lift upto 1.5m,
including getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m.
Ordinary rock Cum 531.75 531.75

2.6 Filling available excavated earth (excluding rock) in trenches,
plinth, sides of foundations etc layers not exceeding 20cm plinth,
sides of foundations etc layers not exceeding 20cm and watering
lead up to 50 mtr and lift up to 1.5 metres
Cum 252.65 252.65
2.70 Felling trees of girth (measured at a hight of 1 mtr above ground
level ) including cutting of trunks and branches removing the roots
and stacking of servicable materials and disposable opf
unservicable materials .
2.7.1 (a) Byond 30 cms and upto 60 cm in girth Each 412.01
2.7.2 (b) Byond 60 cms and upto 120 cm in girth Each 1840.33
2.7.4 Felling trees of girth (measured at a hight of 1 mtr above ground
level ) including cutting of trunks and branches removing the roots
and stacking of servicable materials and disposable opf
unservicable materials ( Tree with Thorn like Muruk etc..)
2.8 Excavating trenches of required width of pipes, cables, etc including
excation for sockets and dressing of sides, ramming of bottoms,
depth upto 1.5 m including getting out the excavated soil and then
returning the soil as required in layers not exceeding 20 cm in
depth, includingconsolidating each deposited layer by ramming,
watering etc. and depositing of surplus excavated soil as directed,
with in lead od 50 m All kind of soil
2.8.1 Pipes, cables etc not exceeding 80 mm dia Mtr 249.50

2.8.2 Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia
Mtr 407.50
2.8.3 Pipes, cables etc exceeding 300 mm dia but not exceeding 600 mm
dia Mtr 636.15
2.9 Supplying and Filling Plinth with Red Mud under floors including
watering ,ramming, consolidating and dressing complete
Cum 4215.08 393.75
2.10 Filling with Quarry waste/debris ( Dismantled materials issued by
department) in trenches, plinth, sides of foundations etc layers not
exeeding 20cm plinth, side od foundations etc layers not exceeding
20cm and watering lead up to 50 mtr and lift up to 1.50mtr
including loading , transportation and unloading at site. Cum 1140.80
2.11 Re- alingment of water supply pipe line like PVC HDPE ,Electrical
cable, Telephonr cables etc.. along the road side Mtr 34.85
3. SH :- PLAIN CEMENT CONCRETE ( M. Sand )

Labour
Rate
3.1 Providing and laying in position cement concrete of specified grade
excluding the cost of centring and shuttering --All work upto plinth
level:
1:1:2 ( 1 Cement: 1 coarse sand : 2 graded stone aggregate 20 mm
Cum 17411.35 3666.61
3.1.1 nominal size)
3.2
Providing and laying in position cement concrete of specified grade
excluding the cost of centring and shuttering -All kind of works
3.2.1 1:1.5:3 ( 1 Cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm
Cum 14125.20 3547.71
nominal size)
3.3 Providing and laying cement concrete 1:2:4 ( 1 cement: 2 M.Sand: 4
Cum 13617.17 3561.20
granite chips 20 mm nomoinal size) foundation and plinth.
3.4 Providing and laying cement concrete 1: 3:6 ( 1 cement: 3 M.Sand:6
Cum 12980.58 3576.50
granite chips ) all work up to plinth level.
3.5 Providing and laying cement concrete 1: 4:8 ( 1 cement: 4 M.Sand: 8
granite chips ) foundation and plinth.Stone aggregate 40mm Cum 12131.80 3501.27
nomonal size
3.6 Providing and laying cement concrete 1: 5:10 ( 1 cement: 5 M.Sand:
10 granite chips ) foundation and plinth.Stone aggregate 40mm Cum 11688.16 3103.65
nomonal size
3.7 Providing and fixing at or near ground level precast cement
concrete in kerbs, edgings etc. as per approved pattern and setting
in position with cement mortar 1:3 (1 Cement: 3 M sand) including
the cost of required centring, shuttering and finishing smooth with
6mm thick cement plaster 1:3 (1 cement: 3 fine sand) on exposed
surfaces complete.
3.7.1 1:2:4 ( 1 cement: 2 coarse sand : 4 graded stone aggregate 20mm

Cum 13873.36 3720.83
nominal size).
D.P.C 1:2:4
3.8 Providing and laying DPC 40 mm in cement concrete 1: 2 :4 ( 1
Sqm 628.00 219.50
cement: 2 M.Sand: 4 granite chips 20mm nominal size)
3.9 Providing and laying DPC 50 mm in cement concrete 1: 2 :4 ( 1
Sqm 768.06 257.44
cement: 2 M.Sand: 4 granite chips 20mm nominal size)
SH:4. R.C.C WORK with M.sand

Labour
Rate
4.1 Reinforced cement concrete 1:1.5:3 ( 1 cement: 1.5 M.Sand: 3
granite chips 20mm nominal size) excluding cost of centring
and shuttering and reinforcement All work up toplinth level.
Foundation fooltings bases of column etc, and mass concrete.
Cum 14653.67 3690.10
4.2
Providing and laying in position specified grade of reinforced
cement concrete excluding the cost of centring, shuttering, finishing
and reinforcement - All work upto plinth level: 1:1:2 (1 cement: 1
coarse sand : 2 graded stone aggregate 20 mm nominal size). Cum 16934.80 4191.34
4.3 Providing and laying in position specified grade of reinforced
cement concrete excluding the cost of centring, shuttering, finishing
and reinforcement - All kind of work upto plinth level :1:2:4 (1
cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size) Cum 14145.66 4089.68
4.4
Reinforced cement concrete work in walls (any thickness), including
attached pilasters, buttresses, plinth and string courses, fillets,
columns, pillars, piers,abutments, posts and struts etc. upto floor
five level excluding cost of centring,shuttering, finishing and
reinforcement :1:1:2 (1 cement: 1 coarse sand : 2 graded stone
aggregate 20 mm nominal size) Cum 18629.87 5886.41
4.5 Reinforced cement concrete work in (wall any thickness )
including attached pilasters,buttresses,plinth and string
course,fillets,columns,pillars,piers,abutments,post and struts
etc.. up to floor five level excluding cost of centering and
shuttering finishing and reinforcement.
1:1.5:3 ( 1 cement :1.5 coarse sand :3 graded stone aggregate 20
mm nominal size Cum 17842.64 5756.87
4.6 Reinforced cement concrete work in beams, Suspended floors
,roofs,having slope up to 15 degree landings, shelves chajjas,
lintels ,bands,plain window sills,staircase and spiral stair case
up to floor five level excluding cost of centering and
shuttering finishing and reinforcement.with 1:1.5:3 ( 1 cemet
:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size ) Cum 16856.46 5367.85
4.7 Cold twisted steel reinforcement for R.C.C. work including bending,
binding and placing in position complete. Kg 80.48 17.92
4.8 Providing precast cement concrete jalli 1:2:4 (1 cement 2 coarse
river sand 4 graded stone aggregate 6mm nominal size) roughning
cleaning fixing in cement mortar 1:3 (1 cement 3 fine river sand) etc.
complete up to first floor level excluding plaster of the jam sills and
soffits.
4.8.1 50mm thick Sqm 1673.64 953.77

4.8.2 40mm thick Sqm 1340.00 839.84
4.8.3 25mm thick Sqm 1150.11 828.79
4.9 Providing precast cement concrete Charupadi 1:1.5:3(1 cement 1.5
coarse river sand 3 graded stone aggregate 6mm nominal size)
roughning cleaning fixing in cement mortar 1:3 (1 cement 3 fine
river sand) etc. complete .
mtr 2653.02 1612.76
4.10 Providing and fixing precast cement concrete 1:2:4 ( 1 cement: 2

M.Sand: 4 graded stone aggregate 20mm nominal size) set in
position with cement mortar 1:2 (1 cement :2 fine sand) and
finished smooth with 6mm thick cement plaster 1:3 (1 cement :3 fine
sand) on exposed surfaces including centering and shuttering in -
(a) String courses, copings, bed plates anchor blocks, plain window
sills and the like Cum 21777.63 9375.16
4.11
Mtr 65.68 63.88
Providing throating or plastering drip and moulding to R.C.C chajjas
4.12 Providing and fixing chicken mesh with cement concrete 1:1.5:3 ( 1
cement 1.5 M.sand and 3 baby chips 10 mm nominal size ) for ferro
cement tank Sqm 421.55 92.62
4.13 Reinforced cement concrete work in well-steining excluding
the cost of centring,shuttering, finishing and reinforcement
with 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate
20 mm nominal size). Cum 13686.86 3630.89
SH:4.CENTERING & SHUTTERING

Labour
Rate
Centring and shuttering including strutting, propping etc. and
removal of form for :
4.14. Foundations, footings, bases of columns, etc. for mass concrete.
Sqm 368.49 196.80
Walls (any thickness) including attached pilasters, buttresses,
Sqm 697.21 531.12
plinth and string
Suspended floors, roofs, landings, balconies and access
Sqm 659.48 587.19
platform.
Shelves (Cast in situ) Sqm 660.13 611.73
Lintels, beams, plinth beams, girders, bressumers and
Sqm 504.43 458.61
cantilevers.
Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 820.37 591.06
Stairs, (excluding landings) except spiral-staircases. Sqm 722.23 405.26
Spiral staircases (including landing). Sqm 660.85 222.13
4.15.9 Centring and shuttering including strutting, propping etc. and
Sqm 367.72 52.53
removal of form for :Well steining
SH:- 5.BRICK WORK( with M. sand )

Labour
Rate
5.1 Brick work with modular bricks of class designation in
foundation and plinth in C.M.1:6 (1Cement: 6 Metal sand) Cum 13678.41 2577.98
5.2 Brick work in super structure above plinth level upto floor five
level Cum 15177.72 3158.54
5.3 Half brick work with modular bricks of class designation in
foundation and plinth in C.M.1:4 (1Cement: 6 Metal sand) Sqm 1727.65 390.48
5.4 Half brick masonry in super structure above plinth level upto
floor five level cement mortar 1:4 ( 1 cement 4 Metal sand ) Sqm 1896.12 558.96
SH:-6.STONE WORK With M.Sand

Labour
Rate
6.1 Casting of cement concrete solid blocks in cement concrete
1:2:2:6 (1 cement: 2 granite powder: 2 metal sand: 6 granite
baby chips) with block casting machine installed at LPWD
storeyard at Kavaratti including operation by daily cum 9288.55 1851.43
maintenance of machine, curing of blocks and stacking as
directed by the Engineer-in-Charge. (Size of blocks:
40cmx20cmx15cm)
6.2 Cement concrete block (machine moulded) masonry in in
Foundation and plinth in CM 1:6 with blocks of size cum 11717.31 2433.85
40cmx20cmx15cm.
6.3 Cement concrete block (machine moulded) masonry in
Superstructure above plinth level in CM 1:6 with blocks of size cum 11837.10 3504.83
40cmx20cmx15cm.
6.4 Random rubble masonry with hard stone in foundation and
plinth including levellingup with cement concrete 1:6:12 (1
cum 10867.02 3567.17
cement: 6 metal sand : 12 graded stone aggregate 20mm
nominal size) at plinth level with :
SH:-7.WOOD WORK
Labour
Rate
7.1 Providing wood work in frames of doors, windows, clerestory
windows and other frames wrought, framed and fixed in
cum 89301.58 21436.67
position-I class Karimaruthu or equivalent ( hold fast lugs or
dasg fastener shall be paid for separately )
7.2 Providing wood work in frames of false ceiling, partitions etc.
cum 84045.44 10874.49
sawn and put up in position :
7.3 Providing and fixing 35 mm thick panelled, glazed or panelled and
glazed shutters for doors windows and clerestory windows
including anodised aluminium butt hinges with necessary screws. sqm 3063.70 1115.69
First class Karimaruthu or equivalent ( Double leef shettre)
7.4 Providing and fixing 30 mm thick panelled, glazed or panelled

and glazed shutters for doors windows and clerestory
sqm 2839.45 1110.86
windows including anodised aluminium butt hinges with
necessary screws. First class Karimaruthu or equivalent
7.5 Providing and fixingpanelling or panelling and galzing in
panelled or panelled and glazed shutters for doors,wndows
and celestory windows (Areaof opening for panel inserts
excluding portion insidegrooves or rebates to be
measured).Panelling for panelled or panelled and glazed
shutters 25 mm to 40 mm thick. Float glass panes
#REF! 4 mm thick glass pane sqm 1983.89 465.85
7.6 Providing and fixing Flush door shutters confirming to IS:2202
(part.I) decorative type,core of block board construction frame
of first cladd hard wood and well matched firdt class teak 3
ply veneering with vertical grains or cross band s and face
veneers on both faces of shutters
#REF! 35 mm thick including ISI marked Stainless steel butt hinges
sqm 4515.05 448.12
with necessary screws
7.7 Providing and fixing karimaruthu wood or equivalent 25 mm
squre wooden bars at required spacing in wooden frames of metre 113.84 66.21
windows and clerestory windows
7.8 Providing 40 x5 mm Iron hold fast 40 cm long including fixing
to frames with 10 mm dia bolts nuts , wooden plugs and
embedding in cement concrete block of size 30 x10 x15 cm of each 241.91 101.68
mix 1:3:6 ( 1 cement : 3 river sand : 6 graded stone agrigate of
20 mm nominal size )
7.9 Providing and fixing 18 mm thick, 150 mm wide pelmet of coir
veneer board ISI marked IS : 14842 - 2000, including top cover
of 6 mm coir veneer board, nickel plated M.S. Pipe 20 mm dia
metre 873.60 209.14
(heavy type) curtain rod with nickel plated brackets including
fixing with 25x3 mm M.S. Flat 10 cm long and rawl plug 50
mm long (designation 10 No.) etc., all complete
7.10 Providing 50x50x50mm 2nd class teak wood plugs including
cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 each 42.22 19.23
fine sand) and making good the walls etc.
7.11 Providing and fixing curtain rods of 1.25 mm thick chromium

plated brass plate,with two chromium plated brass brackets
fixed with C.P. brass screws and wooden plugs, etc., wherever
necessary complete :
20 mm dia. metre 656.95 23.54
7.12 Providing and fixing nickel plated M.S. pipe curtain rods with
nickel plated brackets:
#REF! 20 mm dia (heavy type) metre 203.60 8.36
7.13 Providing and fixing anodised Aluminium sliding door bolt
anodised transparent or dyed to required color and shade
with bolts , nuts and screws etc complete.
7.13.1 300x16 mm each 480.24 23.06
7.13.2 250x16 mm each 417.89 23.06
7.13.3 200x10 mm each 325.13 9.26
7.13.4 150x10 mm each 304.34 9.26
7.14 Providing and fixing anodised Aluminium tower bolt (barral
type) anodised transparent or dyed to required color and
shade with bolts , nuts and screws etc complete.
7.14.1 225x10mm each 240.27 14.34
7.14.2 200x10 mm each 215.33 14.34
7.14.3 150x10 mm each 185.42 9.38
7.14.4 100x10 mm each 155.77 9.19
7.15 Providing and fixing anodised Aluminium handle anodised
transparent or dyed to required color and shade with bolts ,
nuts and screws etc complete.
7.15.1 125 mm each 156.79 7.09
7.15.2 100 mm each 141.65 6.94
7.15.3 75 mm each 121.65 6.94
7.16 Providing and fixing anodised Aluminium hooks and eyes
anodised transparent or dyed to required color and shade
with bolts , nuts and screws etc complete.
7.16.1 200 mm each 148.64 8.19
7.16.2 150 mm each 137.02 7.28
7.17 Providing and fixing brass tower bolt (barral type) with
necessarys screws etc complete.
7.17.1 Brass tower bolt 250x10mm each 448.45 10.08
7.17.2 Brass tower bolt 200x10mm each 402 9.76
7.18 Providing and fixing brass handle with necessarys screws etc
complete.
7.18.1 Brass handlet 125 mm each 321.98 6.05
7.19 Providing and fixing brass door latch with necessarys screws
etc complete.
7.19.1 Brass door latch 300x16x5 mm each 1111.15 11.78
7.19.2 Brass door latch 250x16x5 mm each 988.13 11.78
7.2 Providing and fixing Bright finished brass casement stay with
necessary screws .
7.20.1 300 mm weighing not less than 330 gms each 326.08 9.45
7.21 Providing and fixing special quality Bright finished brass cup
board or ward robe lock with four levers of approved quality each 351.47 15.80
with necessary screws etc.. Complete.
7.22 Providing and fixing Bright finished brass door stoper with
each 123.87 3.34
rubber cusion & necessary screws .
7.23 Providing and fixing 50mm Bright finished brass cup board or
each 83.38 13.56
wardrobe knob with necessary screws .
7.24 Providing and fixing 100mm Bright finished brass mortice
latch and lock with 6 levers and a pair of lever handles with each 1578.32 16.53
necessary screws .
7.25 Providing and fixing Bright finished brass Hydraulic door
each 1930.08 87.84
closer with necessary fittings &screws .
7.26 Providing and fixing M.S Grills of required pattern in frames
of windows etc. with M.S flats squre or round bars etc.
including priming coat with approved steel primer all
acomplete
7.26.1 Fixed to steel windows by welding Kg 175.98 91.34
7.26.2 Fixed to openings/wooden frames with rawl plugs screws etc

Kg 220.89 94.24
7.27 Providing and fixing fly proof stainless steel grade 304 wire
guage to window and clearstory windows using wire guage
with average width of aperture 1.4mm in both direction with Sqm 2504.58 372.50
wire dia 0.50mm all complete. With 2 nd class teak wood
beading 62x19 mm
7.28 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia
wire and 1.4 mm wide aperture with matching wood beading Sqm 2526.54 871.64
for door
7.29 Providing and fixing Aluminium curtain rods with Aluminium
Mtr 303.23 8.61
brackets:
20 mm dia (heavy type)
7.30 Providng and fixing Aluminium tee chanel (heavy duty) with
Mtr 108.71 4.18
rollers and stop end in pelmets as curtain rod
7.31 Providng and fixing Autocose hinges of single pivot in die-cast
each 201.14 25.20
zinc of suprior quality brand and manufacture
7.32 Providng and fixing Special quality bright finshed brass
cupboard or ward robe locks with four levers of approved each 420.81 165.28
quality including necessary screws etc.. Complete 40 mm size
7.33 Providng and fixing Powder coated telescopic drawer channels
300 mm long with necessary screws etc… complete as per the each 488.63 24.03
direction of Engineer-in-charge.
7.34 Providing and fixing Pre-laminated medium density particle
board exterior grad (Grade1) IS:14587:1998 marked,to frame
,backing orstudding with screws etc..( Frame,backing or
Sqm 1476.06 256.48
studding to be paid separately) Pre- laminated with
decorative lamination on both side exterior grade-1 MDF
board 18 mm thick confirming to IS 14587
7.35 Providing and fixing M.S welded mesh 50x50x mm in wooden
frame with necessary nails ( frame work paid by seperatly) Sqm 279.65 220.36
SH:-7.PVC ITEMS
Labour
Rate
7.36 Providing and fixing to existing door frames. 24 mm thick
factory made PVC door shutters made of styles and rails of a
UPVC hollow section of size 59x24 mm and wall thickness 2
mm ± 0.2 mm with inbuiltedging on both sides. The styles and
rails mitred and joined at the corners by meansof M.S.
galvanised/plastic brackets of size 75x220 mm having wall
thickness 1.0 mm and stainless steel screws. The styles of the
shutter reinforced by inserting galvanised M.S. tube of size
20x20 mm and 1 mm ± 0.1 mm wall thickness. The lock ail
made up of’H’ section, a UPVC hollow section of size 100x24 sqm 4123.76 283.05
mm and 2 mm ± r 0.2 mm wall thickness fixed to the shutter
styles by means of plastic/galvanised M.S. ‘U’ cleats. The
shutter frame filled with a UPVC multi-chambered single
panel of size not less than 620 mm, having over all thickness of
20 mm and 1 mm ± 0.1 mm wall thickness . The panels filled
vertically and tie bar at two places by inserting horizontally 6
mm galvanised M.S. rod and fastened with nuts and washers,
complete as per manufacturer’s specification and direction of
Engineer-in-charge. (For W.C. and bathroom door shutter).
7.37 Providing and fixing to existing door frames. Providing and
fixing to existing door frames. 30mm thick factory made
Polyvinyl Chloride (PVC) door shutter made of styles and rails
of a UPVC profile section of size 30mm x 60mm and wall
thickness 2mm ±0.2mm with inbuilt decorative moulding
edging on one side. The styles and rails with plastic brackets of
size 75x220mm mitre and welded at the corners. The- stiles of
the shutter reinforced by inserting galvanized M.S. tube of size
25x20mm and 1mm ± 0.1mm wall thickness. The lock rail sqm 4373.11 283.05
made up of ‘H’ section, a UPVC profile section of size 30mm x
100mm and 2mm±0.2mm wall thickness welded to the shutter
style with a UPVC profile section single panel of size not less
than 620mm, having overall thickness of 20 mm and 1 mm±0.1
mm wall thickness with 20 mm panel beading of suitable size
/Glass(4mm thick plain glass)/louver section, louver rame of
suitable size, as per manufactures specification and direction of
Engineer-in-charge. (For W.C. and bathroom door Shutter)
7.38 Providing and fixing to existing door frames. 25mm thick PVC
flush door shutters upto 737mm width of colour and shade as
approved by Engineer-in-charge made out of a one piece Multi
chamber extruded PVC section of the size of 762mm X 25mm
or less as per requirement with an average wall thickness of
1mm ± 0.3mm. PVC foam end cap of size 23x10mm are
provided on both vertical edges to ensure the overall thickness
of 25mm. An MS tube having dimensions 19mm x 19mm is
sqm 3999.07 283.05
inserted along the hinge side of the door. Core of the door
shutter should be filled with High Density Polyurethane foam.
The Top & Bottom edges of the shutter are covered with an
end-cap of the size 25mm X 11mm. Door shutter shall be
reinforced with special polymeric reinforcements as per
manufactures’ specification and drawing to take up necessary
hardware and fixtures. Stickers indicating the locations of
hardware will be pasted at appropriate places
7.39 Providing and fixing factory made P.V.C. door frame of size
50x47mm with a wall thickness of 5mm, made out of extruded
5mm rigid PVC foam sheet mitred at corners and joined with 2
Nos. of 150mm long brackets of 15x15mm M.S. square tube,
the vertical door profiles to be reinforced with 19x19mm M.S.
metre 693.68 50.53
square tube of 19 gauge,EPDM rubber gasket weather seal to
be provided through out the frame. The door frame to be fixed
to the wall using M.S. screws of 65/100mm size complete as
per manufacturers specification and direction of Engineer-in-
Charge.
7.40 Providing and fixing Fiber Glass Reinforced plastic (FRP)
Door Frames of cross-section 90mm x 45mm having single
rebate of 32mm x 15mm to receive shutter of 30mm thickness
.The laminate shall be molded with fire resistant grade
unsaturated polyester resin and chopped mat .Doorframe metre 743.56 53.66
laminate shall be 2mm thick and shall be filled with suitable
wooden block in all the three legs. The frame shall be covered
with fibreglass from all sides. MS stay shall be provided at the
bottom to steady the frame.
7.41 Providing and fixing to existing door frames.30 mm thick
Glass Fibre Reinforced Plastic (FRP) panelled door shutter of
required colour and approved brand and manufacture, made
with fire - retardant grade unsaturated polyester resin,
moulded to 3 mm thick FRP laminate for forming hollow rails
sqm 3795.22 300.24
and styles, with wooden frame and suitable blocks of seasoned
wood inside at required places for fixing of fittings, cast
monolithically with 5mm thick FRP laminate for panels
confirming to TADS 6: 1993 and / or IS: 14856 - 2000 including
fixing to frames.
SH:-8. STEEL WORK

Labour
Rate
8.1 Structural steel work riveted, bolted or welded in built up

sections, trusses and framed work, including cutting, hoisting,
Kg 157.23 35.16
fixing in position and applying a priming coat of approved
steel primer all complete:
8.2 Providing and fixing in position collapsible steel shutters with
vertical channels 20xl0x2mm and braced with flat iron
diagonals 20x5mm size with top and bottom rail of T-iron
sqm 10318.71 5831.70
40x40x6mm with 40mm dia, steel pulleys complete with bolts,
nuts, locking arrangement, stoppers, handles, including
applying a priming coat of approved steel primer.
8.3 Supplying and fixing rolling shutters of approved make, made
of required size M.S.laths interlocked together through their
entire length and jointed together at the end by end locks
mounted on specially designed pipe shaft with brackets, side
guides and arrangements for inside and outside locking with
push and pull operation complete including the cost of
providing and fixing necessary 27.5cm long wire springs grade
No.2 and M.S. top cover of required thickness for rolling
shutters.
8.3.1 80xl.25mm M.S. laths with 1.25 mm thick top cover. sqm 3419.25 637.40
8.3.2 80x1.20 mm M.S. laths with 1.20 mm thick top cover sqm 2725.61 637.40
8.3.3 80x0.90 mm M.S. laths with 0.90 mm thick top cover. sqm 2636.68 637.40
8.3.4 Providing and fixing ball bearing for rolling shutters Each 644.03 54.07
8.4 Steel work in built up tubular trusses including cutting,
hoisting fixing in position and applying a priming coat of
approved steel primer, welded and bolted including special
shaped washers etc. complete.
8.4.1 Hot finished welded type tubes Kg 256.39 55.78
8.4.2 Hot finished seamless type tubes Kg 286.40 61.76
8.4.3 Electric resistance or induction butt welded tubes. Kg 326.43 61.76
8.5 Providing and fixing M.S. fan clamp type I or II of 16 mm dia
M.S. bar bent to shape with hooked ends in R.C.C. slabs,
Each 175.67 67.37
beams during laying including painting the exposed portion of
loop, all as per standard design complete.
8.6 Providing and fixing M.S. round holding down with nuts and
Kg 145.25 16.15
wahser plates completes.
8.6.1 Providing and fixing bolts including nuts and washers
Kg 202.45 71.56
complete.
8.7 Providing and fixing hand rail of approved size by welding
etc. to steel ladder rail-ing, balcony railing and staircase railing
including applying a priming coat of approved steel primer.-
8.7.1 M.S. tube Kg 266.11 61.18
8.7.2 E.R.W. tubes. Kg 346.13 68.88
8.7.3 G.I Pipe Kg 187.18 59.35
8.8 Providing and fixing stainless steel ( Grade304) railing made of

Hollow tubes,channels,plates etc...includingwelding
grinding,buffing,polishing and making curvature( wherever
required) and fitting the same with necessary stainless steel
nuts and bolts complete,i/c fixing the railing with necessary
accessories & stainless steel dash fasteners,stainless steelbolts Kg 833.94 138.20
etc... of required size,on the top of the floor or the side of waist
slab with suitable arrangement as per approval of Engineer-in-
charge ( for payment purpose only weight of stainless steel
members shall be considered excluding fixing accessories such
as nuts,bolts,fasteners etc..)
8.90 Steel work welded in built up section / framed work including

cutting, hoisting, fixing in position and applying a priming
coat of approved steel primer usin’g structural steel etc. as Kg 163.30 52.10
required. In grating, frames, guard bar, ladder, railings,
brackets,gates and similar works.
8.10
Providing and fixing factory made ISI marked steel glazed doors,
windows and ventilators side /top /centre hung with beading and
all members such as F7D,F4B,KlIB and K12 B etc. complete of
standard rolled steel sections, joints mitred and flash butt welded
and sash bars tenoned and rivetted including providing and fixing
hinges pivots including priming coat of approved steel primer,but
excluding the cost of other fittings per approved design (
Sectional weight of only steel members shall be measured for
payment) Fixing with 15x3 mm lugs 10 cmsembeded in .in cement
concrete blocks 15x10x 10cm of CC1:3:6 ( 1 cement 3 M.sand 6
stone aggregate 20 mm nonminal size) Kg 200.50 29.40
8.11
Providing and fixing pressed steel door frames confirming to IS:

4351 manufactured from commercial mild steel sheet of 1.25 mm
thickness including hinges jamb, lock jamb, bead and if required
angle threshold of mild steel angle of section 50x25mm,or base ties
of 1.60mm pressed mild steel welded or rigidly fixed together by
mechanical means, adjustable lugs with split end tail to each jamb
including steel butt hinges 2.5mm thick with mortar guards, lock
strike-plate and shock absorbers as specified and applying a coat of
approved steel primer after pre-treatment of the surface as directed
by Engineer-in-charge: Profile B Fixed with adjustable lugs with
split end tail to each jamb mtr 625.02 66.14
SH:-9. FLOORING( with M.sand )

Item No Labour
Specification Unit Rate
Rate
9.1 Cement concrete flooring 1:2:4 ( 1 cement, 2 metal sand,4
granite chips ) finished with floating coat of neat cement
,including cement slurry ,but excluding the cost of noising of
steps etc…complete
a) 40mm thick with 20 mm nominal size stone aggregate Sqm 867.85 422.29
9.2 Cement plaster skirting (upto 30cm.height) with cement

mortar 1:3 (1cement: 3 metal sand) finished with floating coat
of neat cement including rounding of junctions with floor.
Sqm 663.15 449.54
9.3 Providing and fixing 1st quality ceramic glazed wall tiles
confirming to IS:15622 ( thickness to be specified by the
manufacture ) of approved make,in all colours,shades except
burgundy ,bottle green,black of any size as approved by
engineer-in-charge in skirting,risers of steps and dado over
12mm thick cement mortar 1:3 ( 1cement, 3 metal sand ) and
joining with grey cement slurry @3.3 kg per sqm,including
pointing in white cement mixed with pigment of matching
shade complete. Sqm 1483.29 545.40
9.4 Providing and fixing ceramic glazed floor tiles of size

300x300mm (thickness to be specified by the manufacture ) of
first quality confirming to IS:15622 of approved make,in
colours such as White ,ivory,Grey,Fume red brown,laid on 20
mm thick cement mortar 1:4 ( 1cement, 4 metal sand ) and
joining with white cement and matching pigment etc...
complete.
Sqm 1579.42 474.18
9.5 Providing and laying vitrified floor tiles (premium quality )
in diffren sizes ( thickness to be specified by the manufacture
) with water absorbtion less than 0.08 % and confirming to IS:
15622 of approved make in all coulers and shades, laid 20mm
thick cement mortar 1:4 ( 1 cement 4 metal sand ) including
grouting the joints with white cement and matching pigments
etc.. complete. ( flooring)
Size of tiles 100x1000 mm Sqm 2309.91 474.18
9.6 Providing and laying vitrified (premium quality ) in diffren

sizes ( thickness to be specified by the manufacture ) with
water absorbtion less than 0.08 % and confirming to IS: 15622
of approved make in all coulers and shades, in skirting,riser of
steps,over 12 mm thick bed of cement mortar 1:3 ( 1 cement 3
metal sand ) including grouting the joints with white cement
and matching pigments etc.. complete.
9.7 Chequerred precast cement concrete tiles 22 mm thick in

footpath & courtyard jointed with neat cement slurry mixed
with pigment to match the shade of tiles including rubbing
and cleaning etc. complete on 20 mm thick bed of cement
mortar 1:4 (1 cement: 4 metal sand sand).
Dark shade using ordinary Cement Sqm 1316.48 479.01
9.8 Providing and fixing 10mm thick acid and/or alkali resistant
tiles of approved make and colour using acid and/or alkali
resisting mortar bedding and joints filled with acid and/or
alkali resisting cement as per IS : 4457 complete as per the
direction of Engineer-in- Charge. In flooring on a bed of 10 mm
thick mortar 1:4(1 acid proof cement: 4 metal sand).
Acid and alkali resistant tile. Sqm 242.69 1860.64
9.9 Providing and laying vitrified tiles in floor with diffrent sizes (
thickness to be specified by the manufacture ) with water absorbtion
less than 0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, laid with cement based high
polymer modifeid quick set tile adhesive ( water based ). (Khajaria
polished vitrified tiles or equivalent)
9.13 Providing and laying vitrified tiles in diffrent sizes ( thickness to
be specified by the manufacture ) with water absorbtion less than
0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, in skirting , riser of
steps,laid with cement based high polymer modifeid quick set tile
adhesive ( water based ) (Khajaria polished vitrified tiles or
equivalent)

equivalent)
equivalent)
equivalent)
9.17 Providing and laying Ceramic Tiles in floor with diffrent sizes (
polymer modifeid quick set tile adhesive ( water based ) (Khajaria
9.18 Providing and laying Ceramic glazed wall tiles with diffrent
sizes ( thickness to be specified by the manufacture ) with water
absorbtion less than 0.08 % and confirming to IS: 15622 of approved
brand and manufacture, in all coulers and shades,in skirting , riser
of steps,laid with cement based high polymer modifeid quick set
tile adhesive ( water based ) (Khajaria polished vitrified tiles or
equivalent) 300x300 mm Sqm 1718.24 723.96
9.19 Providing and laying vitrified floor tiles (premium quality ) in
diffren sizes ( thickness to be specified by the manufacture ) with
water absorbtion less than 0.08 % and confirming to IS: 15622 of
approved make in all coulers and shades, laid 20mm thick cement
mortar 1:4 ( 1 cement 4 metal sand ) including grouting the joints
with white cement and matching pigments etc.. complete. ( flooring)
(Khajaria polished vitrified tiles or equivalent)



with white cement and matching pigments etc.. complete. (
flooring)(Khajaria polished vitrified tiles or equivalent)

9.23 Providing and laying vitrified (premium quality ) in diffren sizes
( thickness to be specified by the manufacture ) with water
make in all coulers and shades, in skirting,riser of steps,over 12 mm
thick bed of cement mortar 1:3 ( 1 cement 3 metal sand ) including
grouting the joints with white cement and matching pigments etc..
complete. (Khajaria polished vitrified tiles or equivalent)




9.26 Providing and fixing 10mm thick acid and/or alkali resistant
tiles of approved make and colour using acid and/or alkali
resisting mortar bedding and joints filled with acid and/or
alkali resisting cement as per IS : 4457 complete as per the
direction of Engineer-in- Charge. In flooring on a bed of 10 mm
thick mortar 1:4(1 acid proof cement: 4 coarse sand)Acid and
alkali resistant tile.. Sqm 1767.78 430.11
9.27 25mm wooden planking, tongued and grooved in flooring
including fixing with iron screws complete with :second class
teak wood Sqm 1256.09 371.58
9.28 38mm thick wood block flooring of first class teak wood laid
over 25mm thick levelling layer of cement concrete 1:2:4 (1
cement: 2 coarse sand : 4 graded stone aggregate 10mm
nominal size) to be paid separately coated with a thin layer of
hot bitumen (blown type) @ 2.45 kg per sqm. including fixing
blocks in position after dipping in hot bitumen (blown type)
upto half depth, planed, levelled smooth and finished
complete. Sqm 5759.16 4933.88
9.29 Cement concrete pavement with 1:2:4 (1 cement : 2 M. sand : 4
grated stone aggregate 20 mm nominal size) including finishing
complete. Cum 14148.78 4092.80
9.30 Chequerred precast cement concrete tiles 22 mm thick in footpath &
courtyard jointed with neat cement slurry mixed with pigment to
match the shade of tiles including rubbing and cleaning etc.
complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4
metal sand sand).Dark shade using ordinary Cement Sqm 1316.48 479.01
9.31 Providing and laying bitumen mastic wearing course (as per
specifications) with industrial bitumen of grade 85/ 25
conforming to IS : 702, prepared by using mastic cooker and
laid to required level and slope,including providing antiskid
surface with bitumen precoated fine grained hard stone
chipping of approved size at the rate of 0.005 cum per 10 sqm
and at approximate spacing of 10 cm centre to centre in both
directions, pressed into surface protruding 1 mm to 4 mm over
mastic surface, including cleaning the surface, removal of
debris etc. all complete. ( Considering bitumen using 10.2% as
per MORTH specification).25 mm thick
Sqm 2111.17 1034.48
9.32 Providing and laying bitumen mastic wearing course (as per
specifications) with industrial bitumen of grade 85/ 25
conforming to IS : 702, prepared by using mastic cooker and
laid to required level and slope,including providing antiskid
surface with bitumen precoated fine grained hard stone
chipping of approved size at the rate of 0.005 cum per 10 sqm
and at approximate spacing of 10 cm centre to centre in both
directions, pressed into surface protruding 1 mm to 4 mm over
mastic surface, including cleaning the surface, removal of
debris etc. all complete. ( Considering bitumen using 10.2% as
per MORTH specification).40 mm thick
Sqm 3380.04 1655.18
Labour Rate( Cement &M.sand issued by the department)

Item No Labour
Specification Unit Rate
Rate
L.1 Providing and fixing 1st quality ceramic glazed wall tiles
confirming to IS:15622 ( thickness to be specified by the
manufacture ) of approved make,in all colours,shades except
burgundy ,bottle green,black of any size as approved by engineer-in-
charge in skirting,risers of steps and dado over 12mm thick cement
mortar 1:3 ( 1cement, 3 metal sand ) and joining with grey cement
slurry @3.3 kg per sqm,including pointing in white cement mixed
with pigment of matching shade complete.
Sqm 1282.03 502.17

L.2 Providing and fixing ceramic glazed floor tiles of size 300x300mm
(thickness to be specified by the manufacture ) of first quality
confirming to IS:15622 of approved make,in colours such as White
,ivory,Grey,Fume red brown,laid on 20 mm thick cement mortar 1:4
( 1cement, 4 metal sand ) and joining with white cement and
matching pigment etc... complete.
Sqm 1330.40 415.06

L.3 Providing and laying vitrified floor tiles (premium quality ) in

L.4 Providing and laying vitrified (premium quality ) in diffren sizes
complete.

L.5 Chequerred precast cement concrete tiles 22 mm thick in footpath &
courtyard jointed with neat cement slurry mixed with pigment to
match the shade of tiles including rubbing and cleaning etc.
complete on 20 mm thick bed of cement mortar 1:4 (1 cement: 4
metal sand sand).Dark shade using ordinary Cement Sqm 1034.818 428.438



with white cement and matching pigments etc.. complete. (
flooring)(Khajaria polished vitrified tiles or equivalent)




SH :-10. ROOFING
Labour
Rate
10.1 Providing corrugated G.S. sheet roofing including vertical/curved
surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm
diameter with bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead and including a coat of approved
steel primer and two coats of approved paint on overlapping of
sheets complete upto any pitch in horizontal/ vertical or curved
surfaces) excluding the cost of purlins, rafters and trusses and
including cutting to size and shape wherever required.
10.1.1 1.00mm thick with zinc coating not less than 275gm/m 2 sqm 1671.14 185.32
10.1.2 0.80mm thick with zinc coating not less than 275gm/m 2 sqm 1420.24 184.89
10.1.3 0.63 mm thick with zinc coating not less than 275gm/sqm sqm 1206.62 184.52
10.2 Providing ridges or hips of width 60 cm over all width plain
G.S. sheet fixed with polymer coated J. or L hooks, bolts and
nuts 8 mm dia. G.I. limpet and bitumen washers complete.
10.2.1 0.80mm thick with zinc coating not less than 275gm/m2 sqm 995.20 398.67
10.2.2 0.63mm thick with zinc coating not less than 275gm/m2 metre 885.64 398.47
10.3 Providing and laying pressed clay tiles (as per approved pattern 20
mm nominal thickness and of approved size) on roofs jointed with
cement mortar 1:4 (1 cement:4 coarse sand) mixed with 2% integral sqm 930.17 280.25
water proofing compound laid over a bed of 20 mm thick cement
mortar 1:4(1 cement: 4 coarse sand) and finished neat complete.
10.4 Providing and fixing insulating board ceiling of approved quality
with necessary nails etc. complete (framework to be paid separately):

10.4.1 Natural colour insulating board 12 mm thick sqm 1102.07 410.92
10.4.2 Providing and fixing insulating board ceiling of approved
quality with necessary nails etc. complete (frame work to be
paid separately):
White face insulating board 12 mm thick sqm 1248.36 410.92
10.5 Providing and fixing flat pressed 3 layer medium density particle
board or graded particle board (Grade I) IS: 3087 marked in ceiling
with necessary nails etc. complete (frame work to be paid
separately):
10.5.1 12 mm thick sqm 1165.55 410.40
10.6 Providing and fixing at all height false ceiling including providing
and fixing of frame work made of special sections power pressed
from M.S. sheet and galvanised in accordance with zinc coating of
grade 350 as per IS : 277 and consisting of angle cleats of size 25mm
wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm
centre to centre one flange fixed to the ceiling with dash fastener
12.5mm diax40mm long with 6mm dia bolts to the angle hangers of
clips made out of 2.64mm diax230mm long G.I. wire at every
junction including fixing the gypsum board with ceiling section and
perimeter channels 0.5mm thick 27mm high having flanges of
20mm and 30mm long, the perimeter of ceiling fixed to
wall/partition with the help of rawl plugs at 450mm centre to
centre with 25mm long drive-all screws @ 230mm interval including
jointing and fixing to a flush finish of tapered and square edges of
the board with recommended filler,jointing tapes, finisher and two
coats of primer suitable for board as per manufactures specification
and also including the cost of making openings for light fittings,
grills, diffusers, cutouts made with frame of perimeter channels
suitably fixed all complete as per drawing and specification and
direction of the Engineer -in-charge but excluding the cost of
painting with:
10.6.1 12.5 mm thick tapered edge gypsum board conforming to IS: 2095-
sqm 1509.01 606.84
Part I,
10.6.2 12.5 mm thick tapered edge gypsum fire resistant board conforming
to IS: 2095- Part I, sqm 1647.34 606.84
10.6.3 12.5 mm thick tapered edge gypsum moisture resistant board sqm 1728.42 606.84
10.7 Providing & fixing on roof pressed clay tile (Mangalor tile of 20
mm nominal thickness and of approved size and as per approved
sqm 517.87 160.50
pattern sfeel frame work complete (steel frame work to be paid
separately)
10.8 Providing & laying on roof pressed clay tile ridge (Mangalore tile)
of 20mm thickness and of approved pattern on steel frame work
complete (sfeel frame work to be paid separately) sqm 230.57 38.57
10.9 Providing and fixing on wall face unplasticised Rigid PVC rain
water pipes conforming to IS : 13592 Type A including jointing with
metre 216.94 101.93
seal ring conforming to IS :5382 leaving 10 mm gap for thermal
expansion, (i) Single socketed pipes 75 mm dia
10.10 Providing and fixing on wall face unplasticised Rigid PVC rain
water pipes conforming to IS : 13592 Type A including jointing with
metre 335.18 123.61
seal ring conforming to IS :5382 leaving 10 mm gap for thermal
expansion, (i) Single socketed pipes 110 mm dia
10.11 Providing Aluminium sheet roofing fixed with .galvnized iron Jor
L hooks and 8mm dia C.I plain bitumen washers complete
Sqm. 1370.37 73.22
excluding the cost of purlins, rafters and trusses corrugated sheet
0.56mm thick.
10.12 Providing ridges or hips in Aluminium sheet roofing with G.I /J or
L hooks bolts and nuts 8 mm dia G.I plain bitumen washers Sqm. 1189.39 97.78
complete. 0.56mm thick.
10.13 Providing and fixing 4mm Bamboo board ceiling of approved

quality with necessary nails etc. complete (frame work to be paid Sqm 992.78 466.09
separately): Bamboo board 4mm thick
10.14 Providing and fixing PVC board ceiling of approved quality with
necessary fittings for fixing PVC ceiling materials with necessary
screws etc.. sqm 760.20 466.09
10.15
Providing non-asbestos high impact Polypropylene reinforced
cement 6 mm thick corrugated sheets (As per IS: 14871) roofing
upto any pitch and fixing with polymer coated J, or L hooks, bolts
and nuts 8mm dia. G.I. plain and bitumen washers or with self
drilling fastener and EPDM washers etc. complete excluding the
cost of purlins, rafters and trusses corrugated sheets and including
cutting to size and shape wherever required sqm 1384.70 127.40
10.16 Providing and fixing ridges and hips in non-asbestos fibre cement
high impact polypropylene reinforced roofing with suitable fixing
accessories or self drilling fastener and EPDM washer etc.
complete.Corrugated serrated adjustable ridges metre 771.30 105.80
10.17 Providing and fixing PVC pipe half round eaves gutter with M.S
brackets including bolts and nuts and necessary fitting as per
approved brand and manufacture etc ..complete 100 mm
(10kg/sqcms) metre 338.88 132.51
(10kg/sqcms) metre 371.58 132.51
(10kg/sqcms) metre 415.63 132.51
SH:-11. FINISHING ( Plastering with Msand)

Item No Specification Unit Rate Labour Rate
11.8 6mm cement plaster to ceiling 1:3(1cement :3 metal sand) Sqm 268.33 141.99
11.9 12mm cement plaster 1:4(1cement :4 metal sand) Sqm 343.01 229.07
11.10 12mm cement plaster 1:6 (1cement :6 metal sand) Sqm 343.90 228.04
11.11 15mm cement plaster 1:3 (1cement :3 metal sand) Sqm 657.81 322.08
11.12 15mm cement plaster 1:6 (1cement :6 metal sand) on rough side of
Sqm 377.78 261.73
single or half brick wall
11.13 12mm cement plaster 1:3 (1cement :3 metal sand) finished with
Sqm 619.68 309.37
floating coat of neat cement
Plastering With Premix
11.14 6mm cement plaster to ceiling with premix 1:3 Sqm 365.90 211.25
11.15 12mm cement plaster with premix1:6 Sqm 499.56 230.04
11.16 15mm cement plaster with premix 1:6 Sqm 585.29 263.37
11.17 12mm cement plaster with premix 1:3 Sqm 804.62 288.79
SH:- PAINTING
11.18 Applying one coat of water thinnable cement primer of approved
brand and manufacture on wall surface.Water thinnable cement Sqm 67.42 55.05
primer
11.19 Distempering with oil bound washable distemper of approved
brand and manufacture to give an even shade.New work ( two or
Sqm 166.14 137.70
more coats) over and including priming coat with water thinnable
cement primer
11.20 Distempering with 1st quality arcylic washable distemper ( ready
mixed )of approved brand and manufacture of required shade and
Sqm 93.12 10.05
colour complete as per manufactures specification.Two or more
coats on new work.
11.21 Finishing wall with water proofing cement paint of approved brand
and manufacture of required shade on new work (two or more coats Sqm 103.59 72.94
applied @3.84Kg/10 sqm)
11.22 Finishing wall with texture exterior paint of required shade on new
work (two or more coats applied @3.28ltr/10 sqm) over including Sqm 246.97 86.14
priming coat of exterior primer applied @ 2.20 kg/10 sqm

11.23 Finishing wall with Arcylic smooth exterior paint of required shade
on new work (two or more coats applied @1.67ltr/10 sqm) over Sqm 160.55 86.14
including priming coat of exterior primer applied @ 2.20 kg/10 sqm

11.24 Finishing with Deluxe Multi surface paint system for interiors and
exteriors using primer as per manufactures specifications two or
Sqm 181.27 86.14
more coats applied on walls @1.25ltr/10 sqm) over including
priming coat of special primer applied @ 0.75 ltr/10 sqm
11.25 Painting Wood work with Deluxe Multi surface paintto give an
even shade.Two or more coats applied on @0.90ltr/10 sqm) over
Sqm 158.87 86.14
under coat of primer applied @ 0.75 ltr/10 sqm of approved and
manufacture
11.26 Painting Steel work with Deluxe Multi surface paintto give an even
shade.Two or more coats applied on @0.90ltr/10 sqm) over under
Sqm 164.84 82.08
coat of primer applied @ 0.80 ltr/10 sqm of approved and
manufacture
11.27 Applying priming coat with ready mixed pink or grey primer of
approved brand and manufacture on wood work ( hard and soft Sqm 59.47 45.80
wood )
11.28 Applying priming coat with ready mixed red oxide zinc chromate
primer of approved brand and manufacture on steel galvanised iron Sqm 52.75 41.92
/steel works
11.29 Finishing with with Epoxy paint (two or more coats) at all locations
prepred and applied as per manufacture's specifications including
Sqm 261.59 153.46
appropriate priming coat ,preperations of surface,etc.. complete on
steel works.
11.30 French spirit polishing f on a new work ( two or more coats )
including a coat of wood filler with ready mixed polish of approved Sqm 442.12 408.69
brand and manufacture.
11.31 Providing and applying white cement based of average thickness
1mm of approved brand and manufacture, over plastered surface to Sqm 156.95 97.68
prepare the surface even and smooth complete.

11.32 Lettering with black japan paint of approved brand and
manufacture Per letter
p er cms 5.90 5.82
hight
11.33 Providing and applying plaster of paris putty of 2mm thickness

over plastered surface to prepare the surface even and smooth Sqm 237.42 197.34
complete. (Birla White or equivalent).
11.34 Providing and applying wall putty of 2mm thickness over plastered
surface to prepare the surface even and smooth complete. (Nerolac Sqm 290.84 197.34
or equivalent).
11.35 Painting Wood work with Deluxe Multi surface paintto give an
even shade.Two or more coats applied on @0.90ltr/10 sqm) over
Sqm 198.77 102.11
under coat of primer applied @ 0.75 ltr/10 sqm of approved and
manufacture (Berger/Birla or equivalent)
11.36 Finishing with Deluxe Multi surface paint system for interiors and
exteriors using primer as per manufactures specifications two or
more coats applied with Teflon coated Royal coated) on walls Sqm 210.72 103.58
@1.25ltr/10 sqm) over including priming coat of special primer
applied @ 0.75 ltr/10 sqm. (Asian Paint or equivalent)
11.37 Finishing wall with Arcylic smooth exterior paint of required shade
on new work (two or more coats applied @1.67ltr/10 sqm) over
Sqm 154.41 102.11
including priming coat of exterior primer applied @ 2.20 kg/10
sqm. (Nerolac paint premier or equivalent). Exterior
11.38 Wall painting with acrylic emulsion paint, having VOC
(Volatile Organic Compound ) content less than 50 grams/
litre, of approved brand and manufacture, including applying Sqm 156.28 111.41
additional coats wherever required, to achieve even shade and
colour.Two coat
11.39 Applying one coat of white cement of approved brand and
manufacture on wall surface. Sqm 45.03 32.67
SH:- 12.WATER SUPPLY

Labour
Rate
12 Providing and fixing nominal gauge O.P. pipes of approved quality
compleate with special O.P. fittings ( of approved make) including
trunching and refilling etc internal works
12.1 15 mm nominal bore Metre 241.71 141.82
12.1.2 20 mm nominal bore Metre 303.20 155.76
12.2
Providing and fixing nominal gauge O.P. pipes of approved
quality compleate with special O.P. fittings ( of approved
make) including trunching and refilling etc External works
12.3
Providing and fixing nominal guage PVC Pipe of approved
quality compleate with special flang compression type fittings
including trenching and re filling etc. Internal work
12.3.1 110 mm nominal bore ( 6 kg/sqcms) Metre 695.26 251.29
12.4
Providing and fixing nominal guage PVC Pipe of approved
quality compleate with special flang compression type fittings
including trenching and re filling etc. External work
12.5 Providing and fixing C.P. Brass bib cock of approved quality
and manufacture complete.
12.5.1 15 mm nominal bore Each 385.25 16.19
12.6 Providing and fixing C.P. Brass stopcook of approved quality
12.7 Providing and fixing G.M. full way wheel valve of approved
quality and manufacture complete.

12.8 Providing and fixing ball valve ( brass ) of approved quality
12.9.1 Providing and fixing C.P. shower rose with 15 to 20mm intlet,
Each 387.62 13.58
100 mm dia.
12.9.2 Providing and fixing C.P. shower rose with 15 to 20mm intlet,
Each 448.42 16.19
150 mm dia.
12.10 Providing and placing sintex tank on terrace ( at floor level )
polythene water storage tank ISI : 12701 marked,with cover
and suitable locking arrangement and making necessary holes
for inlet ,outlet and over flow pipe but without fittings and the
base support for tank
Litre 12.52 1.08
12.10.1 (a) 1000 liter capacity each 12520.00 1081.45
12.10.2 (b) 500 liter capacity Each 6260.00 540.72
12.11.1 Providing and fixing C.P. Brass bib cock of approved quality
coforming to IS:8931.
15 mm nominal bore Each 679.89 23.25
12.12 Providing and fixing C.P. Brass long nose bib cock of
approved quality coforming to IS standard and weighing not
less than 810 gms
12.13
Providing and fixing C.P. Brass stop cock ( concealed ) of
standard design and of approved quality coforming to IS :8931
12.14
Providing and fixing C.P. Brass angle valve for basin mixer
and geyser points of approved quality coforming to IS :8931
12.15.1 Providing and fixing PTMT bib cock of approved quality and
colour
15 mm nominal bore, 86 mm long ,weighing not less than 88
Each 248.93 16.19
gms
12.15.2 15 mm nominal bore, 122 mm long ,weighing not less than 99
Each 312.10 16.19
gms
Each 345.35 16.19
gms
12.16 Providing and fixing PTMT stop cock of approved quality and
colour
Each 224.00 16.19
gms
Each 302.13 16.19
gms
12.7.1 Providing and fixing PTMT push cock of approved quality
and colour
15 mm nominal bore, 98 mm long ,weighing not less than 75
Each 194.06 16.19
gms
SH:- 12.WATER SUPPLY ( CPVC )

Labour
Rate
12.18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)
pipes, having thermal stability for hot & cold water supply
including all CPVC plain & brass threaded fittingsi/c fixing
the pipe with clamps at 1.00 m spacing. This includes jointing
of pipes &fittings with one step CPVC solvent cement and the
cost of cutting chases and making good the same including
testing of joints complete as per direction of Engineer in
Charge. (Concealed work including cutting chases and making
good the walls etc.,)
12.18.1 15 mm nominal outer dia .Pipes. Metre 507.71 155.88
12.19 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply including all
CPVC plain & brass threaded fittings, this included jointing of pipes
& fittings with one step CPVC solvent cement, trenching, refilling &
testing of joints complete as per direction of Engineer in Charge.
(External work).
12.20 Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing
drain pipe etc. and repairing the hole after insertion of drain pipe
etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) including finishing complete Each
so as to make it leak proof. hole 349.22 296.66
12.21 Making chases upto 7.5x7.5 cm in wails including making good and
finishing with matching surface after housing G.I. pipe etc Metre 178.24 140.62
12.22.1 Providing and fixing ball valve ( PVC ) of approved quality and
manufacture complete.63 mm nominal bore Each 394.78 32.40
12.23.1 Providing and fixing PTMT grating of approved quality and
colour.Circular type.
100 mm nominal dia. Each 89.66 8.36
colour.Circular type.
125 mm nominal dia with 25 mm waste hole. Each 105.93 8.36
colour.Rectangular type with openable circular lid.
150 mm nominal size square 100 mm diameter of the inner hinged
round grating. Each 223.50 8.60
12.24 Providing and fixing health faucet of approved quality and

manufacture complete. Each 657.89 19.60
12.25.1 Providing and fixing CP brass angle cock of approved quality and
manufacture complete.20 mm Each 425.59 19.07
12.25.2 Providing and fixing CP brass angle cock of approved quality and
12.26 Providing and fixing CP brass Sink cock of approved quality and
12.27 Providing and fixing PTMT angle stop cock 15 mm nominal
bore, weighing not less than 85gms. Each 306.57 16.20
12.28 Providing and fixing PTMT swivelling shower, 15 mm nominal
bore, weighing not less than 40gms. Each 222.65 13.58
12.29 Providing and fixing PTMT soap Dish Holder having length of
138mm, breadth 102mm, height of 75mm with concealed fitting
arrangements weighing not less than 106 gms. Each 205.23 13.58
12.30 Providing and fixing CP wall mixure tap for hot and cold water of
standard design and of approved quality and manufacture
complete.15 mm Each 5571.25 23.90
SH:13.SANITORY
Labour
Rate
13 Providing anf fixing white vitrous China water closet Pedestal pan
(European) type WC pans with white plastic seat and lid and rubber
buffers, 15 white vitrous China low level flushing system of
approved make with fittings and brackets 40mm flush bend, 20mm
over flow pipe with complete including cutting and making good
the walls and floors where required.
13.1 White EWC pan with plastic seat and lid Each 6139.40 2493.22
13.2 Providing anf fixing white vitrous China wash basin with RS or CI
brackets painted white, 15mm C.P bras pillar tap and C.P brass
chain and rubber plug 32mm C,P. brass waste of standrad pattern
32mm diametre and waste pipe complete including cutting and
making good the walls and floors where required.
13.2.1 White vitreous China Flat back wash basin 550x400mm with one
Each 2902.04 1124.78
15mm C.P. brass pillar tap.
13.3 Providing anf fixing white vitrous China kitchen sink with CI
chain and rubber plug 40mm brass waste of standrad pattern 40mm
diametre and waste pipe complete including cutting and making
good the walls and floors where required.
13.3.1 White gazed fire clay kitchen sink size 600x450x250mm Each 4296.22 993.53
13.4 Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink
asper IS 13983 with CI brackets stainless steel plug 40 mm
,including painting of fittings and brackets, cutting and making
good the walls where required.
13.4.1 Kitchen sink with drain board 510x1040 mm bowl deth 250 mm
Each 10534.53 1455.81
13.5 Providing anf fixing white vitrous China laboratory sink with CI
chain and rubber plug 40mm brass waste of standrad pattern 40mm
diametre and waste pipe complete including cutting and making
good the walls where required.
Sink size 450x300x150mm Each 3653.26 993.53
13.6 Providing anf fixing 600x450mm mirror of superior glass
(approved quality) complete with 6mm thick asbestose sheet Each 1441.08 624.51
ground fixed to wooden cleats with necessary screws and washers.

13.7 Providing and Fixing PTMT towel rail with brackets fixed to
wooden cleats with CP Brass screws with concealed ritting
arrangement of approved quality and colour
600 mm long towel rail brackets with total length of 645 mm,width
78mm and effective height of 88 mm ,weighing not less than 190 Each 920.67 324.29
gms.
13.8 Providing and Fixing PTMT liquid soap container109 mm wide,125
mm high and 112 mm distance from wall of standard shape with
Each 309.89 13.58
brackets of the same materials with snap fittings of approved
quality and colour,weighing not less than 105 gms
13.9 Providing and Fixing l toilet paper holder Vitreous china Each 526.32 210.71
13.10 Providing anf fixing on wall face PVC. soil waste and vent pipe
13.10.1 100mm dia pipes Metre 366.08 77.37

13.10.2 Providing anf fixing on wall face PVC. soil waste and vent pipe
Metre 291.68 63.93
75mm dia pipes
13.11 Providing and Fixing Stainless steel toilet paper holder in the
cavity of wall with screws and washers superior quality of Each 1760.72 217.68
approved brand and manufacture
13.12 Providing and fixing water closet squatting pan (Indian type
W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low
level white P.V.C. flushing cistern with manually controlled
device (handle lever) conforming to IS : 7231, with all fittings
Each 5167.64 2493.22
and fixtures complete including cutting and making good the
walls and floors wherever required : White Vitreous china
Orissa pattern W.C. pan of size 580x440mm with integral type
foot rests.
13.13.1 Providing and fixing white vitreous china flat back or wall
corner type lipped front urinal basin of 430x260x350mm and
340x410x265mm sizes respectively with automatic flushing
cistern with standard flush pipe and C.P. brass spreaders with
Each 3986.49 2909.04
brass unions and G.I clamps complete, including painting of
fittings and brackets,cutting and making good the walls and
floors wherever required :One urinal basin with 5 litre white
P.V.C. automatic flushing cistern.
Each 8382.87 4467.77
floors wherever required :Two urinal basin with 5 litre white
P.V.C. automatic flushing cistern.
Each 11229.31 6236.93
floors wherever required :Range of three urinal basins with
10 litre white P.V.C. automatic flushing cistern.
Each 15725.44 8935.55
floors wherever required :Range of four urinal basins with 10
litre white P.V.C. automatic flushing cistern.
13.14 Providing and fixing trap of self cleansing design with

screwed down or hinged grating with or without vent arm
complete, including cost of cutting and making good the walls Each 1561.19 876.61
and floors: 100 mm inlet and 100 mm outlet Sand cast iron S&S
as per IS: 3989.
13.15 Providing and fixing white vitrous China water closet Pedestal
pan (European) type WC pans with white plastic seat and lid
and rubber buffers, 15 white vitrous China low level flushing
system of approved make with fittings and brackets 40mm
flush bend, 20mm over flow pipe with complete including
cutting and making good the walls and floors where required.
(Jaquar model No SLS-WHT-0311/SLS-WHT-0318 or
Equivalent)
White EWC pan with plastic seat and lid each 15795.34 2928.79
13.16 Providing and fixing white vitrous China wash basin with RS
or CI brackets painted white, 15mm C.P bras pillar tap and C.P
brass chain and rubber plug 32mm C,P. brass waste of
standrad pattern 32mm diametre and waste pipe complete
including cutting and making good the walls and floors where
required
White vitrous china wash basin 550x605x475mm with half
Each 11788.59 1288.55
pedastal (Jaquar modal FNS WHT - 1503 or equivalent)
13.17 Providing and fixing mirror of superior glass (approved
quality) complete with 6mm thick asbestose sheet ground
Each 1810.11 624.51
fixed to wooden cleats with necessary screws and washers. (
Cera model No 5561 size 700x500mm )
13.18 Providing and fixing P.V.C low level flushing cistern with
manually controlled device ( handle lever) confirming to IS Each 1685.88 264.53
:7231 with all fittings and fixtures complete.
13.19 Providing anf fixing Stailess steel A ISI 304 labour room sink
including fitting and brackets,cutting and making good the Each 52350.81 1659.07
walls where required.
13.20 Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink
asper IS 13983 with CI brackets stainless steel plug 40 mm
,including painting of fittings and brackets, cutting and Each 3242.18 1659.07
making good the walls where required. With out drain board
450x400x250 mm
13.21 Providing and fixing 100 mm PVC grating for gully trap. Each 60.90 8.60
13.22 Providing and fixing in position 25mm diameter mosquito
Each 73.45 3.75
proof coupling of approved municipal design.
13.23 Providing and fixing 600x120x5mm glass shelf with edges
round of supported on anodised aluminium angle frame with
C.P. brass brackets and guard rail complete fixed with 40 mm Each 984.10 472.96
long screws, rawl plugs etc., complete.
13.24 Providing and fixing toilet paper holder : C.P. brass Each 678.60 231.90
13.25 Providing and fixing toilet paper holder: Vitreous china Each 599.80 231.90
SH:-14. DRAINAGE
Labour
Rate
14.1 Providing,laying and P.V.C pipes grade "A" with stiff mixture
of 1:3 (1 cemenr 3 metal sand) including testing of joints etc.
complete.
14.1.1 110mm diametre Metre 543.61 168.58
14.2.1 Providing and laying cement concrete 1:5:10 (1 cement : 5
metal sand : 10 graded stone aggregate 40 mm nominal size)
Metre 822.15 218.31
upto haunches of pipes including bed concrete as per standard
design .100mm dia pipe
14.2.2 Providing and laying cement concrete 1:5:10 (1 cement : 5
metal sand : 10 graded stone aggregate 40 mm nominal size)
Metre 1332.45 353.82
upto haunches of pipes including bed concrete as per standard
design : 150 mm diameter pipe
14.3 Dislodging of septic tank including disposal of sludge by
digging a pit within a lead of 50 meters and covering it with
sand including adding disinfectants etc..including washing the
tank and re-arranging of soak pit ,manhole etc..complete as
directed by the Engineer-in-charge.
cum 1627.69 0
SH:-15 ALUMINIUM WORK

Labour
Rate
15.1 Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS : 1285, fixed with
rawl plugs and screws or with fixing clips, or with expansion
hold fasteners including necessary filling up of gaps at
junctions, at top, bottom and sides with required EPDM
rubber/ Neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap
beading for glazing / panelling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the
directions of Engineer- in-charge. (Glazing and panelling to be
paid for separately):For fixed portion.
15.1.1 Anodised aluminium (anodised transparent or dyed to
required shade according to IS: 1868, Minimum anodic coating Kg 855.69 95.72
of grade AC 15)
15.1.2 Powder coated aluminium (minimum thickness of powder
Kg 908.06 95.72
coating 50 micron)
15.2 Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS : 1285, fixed with
rawl plugs and screws or with fixing clips, or with expansion
hold fasteners including necessary filling up of gaps at
junctions, at top, bottom and sides with required EPDM
rubber/ Neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed mechanically
wherever required including cleat angle, Aluminium snap
beading for glazing / panelling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the
directions of Engineer- in-charge. (Glazing and panelling to be
paid for separately):
15.2.1 For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making provision for
fixing of fittings wherever required including the cost of
EPDM rubber / neoprene gasket required (Fittings shall be
paid for separately).
15.2.1.1 Anodised aluminium (anodised transparent or dyed to
required shade according to IS: 1868, Minimum anodic coating Kg 968.66 159.80
of grade AC 15)
15.2.1.2 Powder coated aluminium (minimum thickness of powder
Kg 1022.09 159.80
coating 50 micron)
15.3 Providing and fixing 12mm thick prelaminated particle board
flat pressed three layer or graded wood particle board
conforming to IS: 12823 Grade 1 Type II in panelling fixed in
aluminium doors, windows shutters and partition frames with
C.P. brass / stainless steel screws etc. complete as per
architectural drawings and directions of engineer-in-charge.
15.3.1 Pre-laminated particle board with decorative lamination on
sqm 1755.02 228.92
one side and balancing lamination on other side.
15.3.2 Prelaminated particle board with decorative lamination on

sqm 1793.41 232.07
both sides.
15.4 Providing and fixing glazing in aluminium door, window,
ventilator shutters and partitions etc. with EPDM
rubber/neoprene gasket etc. complete as per the architectural
drawings and the directions of engineer-in-charge . (Cost of
aluminium snap beading shall be paid in basic item):
15.4.1 With float glass panes of 4.0 mm thickness sqm 1476.75 432.79
15.4.2 With float glass panes of 5.50 mm thickness sqm 1759.06 407.89
15.4.3 With float glass panes of 8 mm thickness sqm 2236.51 410.93
15.5 Providing and fixing double action hydraulic floor spring of
approved brand and manufacture IS : 6315 marked, for doors
including cost of cutting floors as required, embedding in
floors and cover plates with brass pivot and single piece M.S.
sheet outer box with slide plate etc. complete as per the
direction of Engineer-in-chargs.
15.5.1 With stainless steel cover plate minimum 1.25 mm thickness
each 3471.99 324.20
15.5.2 With brass cover plate minimum 1.25 mm thickness each 3970.71 324.20
15.6 Filling the gap in between aluminium frame & adjacent RCC/
Brick/ Stone work by providing weather silicon sealant over
backer rod of approved quality as per architectural drawings
and direction of Engineer-in-charge complete.
15.6.1 Upto 5mm depth and 5 mm width each 107.40 47.01
15.7 Providing and fixing aluminium tubular handle bar 32 mm
outer dia, 3.0 mm thick & 2100 mm long with SS screws etc
.complete as per direction of Engineer-in-Charge.
15.7.1 Anodized (AC 15 ) aluminium tubular handle bar each 1189.17 12.50
15.7.2 Powder coated minimum thickness 50 micron aluminium
each 1270.66 12.50
tubular handle bar.
15.8 Providing and fixing 100mm brass locks (best make of
approved quality) for aluminium doors including necessary each 747.12 165.28
cutting and making good etc. complete.
15.9 Providing and fixing aluminium casement windows fastener
of required length or aluminium windows with necessary
screws etc. complete.
15.9.1 Anodized(AC 15) aluminium each 99.55 6.12
15.9.2 Powder coated minimum thickness 50 micron aluminium.
each 100.60 7.17
15.9.3 Providing and fixing aluminium round shape handle of outer
dia 100mm with SS screws etc. Complete as per direction of
Engineer-in-charge.
Powder coated minimum thickness 50 micron aluminium.
each 122.22 7.17
15.10.1 Providing and fixing aluminium grills ( anodised transparent

or dyed to required shade according ti IS:1868 with minimum
anodic coating of grade AC 15 ) approved design /pattern
,with approved standard section and fixed to the existing
window frame with C.P.brass/stainless steel screws @ 200 mm
Kg 866.44 98.41
centre to centre ,including cutting the grills to proper opening
size for fixing and operation of handles and fixing approved
anodised aluminium standard section around the opening ,all
complete as per requirement and direction of Engineer- in-
charge( Only weight of grill to be measured for payment )
15.11 Providing and fixing 12mm thick framless toughened glass
door shutter of approved brand and manufacture,including
providing and fixing top & bottom pivot& spring type fixing
arrangement and making necessary holes etc.. for fixing
required door fittings ,all complete as per the direction of
Engineer-in-charge ( Door handle,lock,and stopper etc.. to be
paid separately . sqm 7769.21 2257.15
SH:16. ROAD WORK with M.sand

Labour
Rate
16.1 Cement concrete 1:2:4 (1 cement : 2 metale sand : 4 graded
stone aggregate 40 mm nominal size) in pavements, laid to
cum 13581.71 2478.64
required slope and camber in panels as required including side
shuttering, consolidation finishing and tamping complete.
16.2 Providing and laying 60mm thick factory made cement
concrete interlocking paver block of M -30 grade made by
block making machine with strong vibratory compaction and
of approved size and design/ shape laid in required colour Sqm 1354.74 225.36
and pattern over and including 50mm thick compacted bed of
Fine sand, filling the joints with fine sand etc. all complete as
per the direction of Engineer-in-charge.
16.3 Supplying at site :R.C.C. Standards post/ struts/rails/ pales of
mix 1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone
aggregate 12.5 mm nominal size) with wooden plugs or 6mm
Cum 36248.03 18125.89
bar nibs, wherever required as per direction of Engineer-in-
charge (cost of earth works in excavation, concrete
worksfoundation to be paid separately).
16.4 Cutting cement concrete road and making good the same
including extra cost of cement concrete 1:2:4 required ect..
cum 2562.41 896.95
Complete and disposal of rubbish etc complete within 50
meters lead
16.5 Providing and fixing G.I. chain link fabric fencing of required
width in mesh size 25x25mm including made of G.I wire of 8
gauge including strengthening with 2mm dia wire or nuts, Sqm 1164.02 383.75
bolts and washers as required complete as per the direction of
Engineer-in-charge.
16.6 Fencing with angle iron post placed at required distance
embedded in cement concrete blocks, every 15th post, last but
one end post and corner post shall be strutted on both sides
and end post on one side only and provided with horizontal
lines and two diagonals interwoven with horizontal wires, of
Mtr 161.67 4.60
barbed wire 9.38 kg per 100 m (minimum) between the two
posts fitted and fixed with G.I. staples, turn buckles etc.
complete. (Cost of posts, struts, earth work and concrete work
to be paid for separately):- Payment to be made per metre cost
of total length of barbed wire used. With G.I. barbed wire
16.7 Supplying and fixing turn buckles and straining bolts for
Sqm 214.32 104.21
barbed wire fencing.
SH:- 17.ANTI SEA EROSION with M.sand

Labour
Rate
17.1 Providing and laying in position cement concrete 1:1.5:3 ( 1
cement: 1.5metal sand: 3 granite chips 20mm nominal size)
excluding cost of centring and shuttering and reinforcement
All work up toplinth level.
Foundation fooltings bases of column etc, and mass concrete.
Cum 14140.19 3562.70
17.2 Providing and fixing in position 0.5 mt Tetrapod in CC 1:1.5:3

( 1 cement: 1.5 metal sand: 3 granite chips 20mm nominal size) Each 4238.21 1341.73
as per approved patern
17.3 Providing andplacng in position hollow blocksof size 60x40x30

cm in cement concrete 1:1.5:3 ( 1 cement: 1.5 metal sand: 3 Each 868.66 329.01
granite chips 20mm nominal size) as per approved patern
17.4 Labour for conveyance of tetrapod manually and Re-arranging
Each 281.25 281.25
as per design
17.5 Labour for conveyance of Hollow Block manually and Re-
Each 118.13 118.13
arranging as per design(
17.6 Providing and laying Granite boulders including
transportation by manual labour loading /unloading and Each 5507.55 1093.84
stacking the same lead less than 0.5 kmts
SH:-18.REPAIRS TO BUILDINGS
Labour
Rate
18.1 Repairs to plaster of thickness 12mm to 20mm in patches of
area 2.5 sq. metres and under including cutting the patch in
proper shape, raking out joints and preparing and plastering sqm 522.17 378.65
the surface of the walls complete including disposal of rubbish
to the dumping ground within 50 metres lead :Cement mortar
1:4
18.2 Fixing chowkhats in existing opening including embedding
chowkhats in floors or walls cutting masonry for holdfasts
embedding hold fasts in cement concrete blocks with cement
concrete 1:3:6 (1 cement : 3 metal sand : 6 graded stone
aggregate 20 mm nominal size) painting two coats of approved each 1563.16 1132.59
wood preservative to sides of chowkhats and making good the
damages to walls and floors as required complete including
disposal of rubbish to the dumping ground within 50 metres
lead :
18.3.1 Renewing glass panes and refixing existing wooden fillets:
Float glass panes of thickness 4 mm sqm 1273.90 542.96

18.4 Raking out joints in lime or cement mortar and preparing the
surface for re-pointing or replastering including disposal of sqm 10.87 10.87
rubbish to the dumping ground within 50 metres lead.
18.5 Providing and fixing 150 mm bright finished floor brass door
stopper with rubber cushion, screws etc. to suit shutter each 347.31 8.33
thickness complete
18.6 Providing and fixing bright finished brass hard drawn hooks
and eyes :
18.6.1 250 mm each 131.27 5.76
18.6.2 200 mm 126.28 5.76
18.7 Providing and fixing chromium plated brass butt hinges with
necessary screws etc. complete.
18.7.1 100x70x4 mm (ordinary type) each 170.33 21.87
18.7.2 75x65x4 mm (heavy type) each 223.78 21.51
18.8 White washing with White cement give an even shade : Old
sqm 23.95 11.32
work (two or more coats)
18.8.1 White washing with White cement to give an even shade :
sqm 13.84 7.47
Old work (one or more coats)
18.9 Removing white or colour wash by scrapping and sand
papering and preparing the surface smooth including sqm 14.74 14.74
necessary repairs to scratches etc. complete
18.10 Distempering with dry distemper of approved brand and
manufacture (one or more coats) and of required shade on old sqm 54.69 45.56
work to give an even shade.
18.11 Distempering with oil bound washable distemper of approved
brand and manufacture to give an even shade : Old work (one sqm 57.34 48.09
or more coats)
18.12 Removing dry or oil bound distemper, water proofing cement paint
and the like by scrapping, sand papering and preparing the surface sqm 18.69 18.69
smooth including necessary repairs to scratches etc. complete.

18.13 Painting on G.S. sheet with synthetic enamel paint of approved
brand and manufacture of required colour to give an even sqm 76.13 64.45
shade : Old work (one or more coats)
18.14 Painting with oil type wood preservative of approved brand

sqm 32.08 19.82
and manufacture Old work (one or more coats)
18.15 Wall painting with plastic emulsion paint of approved brand
and manufacture to give an even shade One or more coats on sqm 100.99 75.60
old work.
18.16 Painting with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade One or sqm 94.67 74.90
more coats on old work.
18.17 Painting with aluminium paint of approved brand and
manufacture to give an even shade One or more coats on old sqm 86.84 74.90
work.
18.18 Painting with acid proof paint of approved brand and
manufacture of required colour to give an even shade One or sqm 91.36 74.90
more coats on old work.
18.19 French spirit polishing: One or more coats on old work. sqm 223.41 206.23
18.20 Re-lettering with black Japan paint of approved brand and Per cm
manufacture. height 3.75 3.69
of letter
18.21 Providing and fixing C.P. brass chain and rubber plug
complete for sink or wash basin :
18.21.1 32mm dia each 63.57 16.19
18.21.2 40 mm dia each 68.55 16.19
18.22 Distempering with 1st quality acrylic washable distemper
(ready made) of approved manufacturer and of required shade
sqm 57.56 46.88
and colour complete, as per manufacturer’s. One or more
coats on old work.
18.23 Finishing walls with water proofing cement paint of required
shade : Old work (one or more coats applied @ 2.20 kg/10
sqm 111.25 79.75
sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm
complete including cost of Priming coat.
18.24 Finishing walls with textured exterior paint of required shade :
Old work (Two or more coats on existing cement paint surface sqm 222.97 75.40
applied @ 3.28Itr/10 sqm.
18.25 Finishing walls with textured exterior paint of required shade
sqm 137.39 54.86
: Old work (One or more coats) applied @ 1.82 ltr/10 sqm.
18.26 Finishing walls with Acrylic Smooth exterior paint of required
shade : Old work (Two or more coat applied @ 1.67 ltr/10 sqm) sqm 135.37 74.72
on existing cement paint surface).
18.27 Finishing walls with Acrylic Smooth exterior paint of required
sqm 88.47 54.86
shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm).
18.28 Finishing walls with Premium Acrylic Smooth exterior paint of
required shade Old work (Two or more coats applied @ 1.43 sqm 143.29 75.29
ltr/10sqm) over existing cement paint surface.
18.29 Finishing walls with Premium Acrylic Smooth exterior paint
with Silicone additives of required shade Old work (one or sqm 95.01 54.94
more coats applied @ 0.83 ltr/10 sqm).
18.30 Varnishing with varnish of approved brand and manufacture:
sqm 93.48 73.83
One or more coats with spar varnish.
18.31 Providing and fixing 16 mm M.S. Fan clamps of standard
shape and size in existing R.C.C. slab, including cutting chase,
anchoring clamp to reinforcement bar, including cleaning, each 586.33 371.10
refilling, making good the chase with matching concrete,
plastering and painting the exposed portion of the clamps
complete.
SH:-19. DEMOLISHING ITEMS

Labour
Rate
19.1 Demolishing cement concrete manually/ by mechanical means
including disposal of material within 50 metres lead as per Cum 1887.81 1887.81
direction of Engineer in charge. 1:3:6 or richer mix
19.2 Demolishing cement concrete manually/ by mechanical means
including disposal of material within 50 metres lead as per Cum 1166.57 1166.57
direction of Engineer in charge. 1:4:8 or leaner mix
19.3 Demolishing R.C.C. work, including stacking of steel bars and
disposal of unserviceable material within 50 metres lead as per Cum 2754.08 2754.08
direction of Engineer - in- charge.
19.4 Demolishing brick work, manually/ by mechanical means
including stacking of serviceable material and disposal of
Cum 1598.53 1598.53
unserviceable materialwithin 50 metres lead as per direction of
Engineer-in-charge. In Cement mortar
19.5 Removing mortar from bricks and cleaning bricks including
stacking within a lead of 50 m (stacks of cleaned bricks shall be Each 5.16 5.16
measured): From brick work in cement mortar
19.6 Demolishing stone rubble masonry manually/by machanical
means including stacking of serviceable material and disposal
Cum 1908.02 1908.02
of unserviceable material within 50 metres lead as per
directionof Engineer-in-charge: In cement mortar
19.7 Dismantling dressed stone work ashlar face stone work,
marble work or precast concrete work manually/by
machanical means incluaing stacking of serviceable and Cum 2233.24 2233.24
disposal of unserviceable material within 50 metres lead
as per direction of Engineer-in-charge: In cement mortar
19.8 Dismantling doors, windows and clerestory windows (steel or
wood) shutter including chowkhats, architrave, holdfasts etc.
Each 279.89 279.89
complete and stacking within 50 metres lead Of area 3 sqm
and below
19.8.1 Dismantling doors, windows and clerestory windows (steel or
wood) shutter including chowkhats, architrave, holdfasts etc.
Each 382.97 382.97
complete and stacking within 50 metres lead Of area beyond
3.00 sqm
19.9.1 Taking out doors, windows and clerestory window shutters
(steel or wood) including stacking within 50 metres lead:

Of area 3 sq. metre and below Each 109.64 109.64
19.9.2 Taking out doors, windows and clerestory window shutters
(steel or wood) including stacking within 50 metres lead:

Of area beyond 3.00 sqm Each 144.11 144.11
19.10 Dismantling wood work in frames, trusses, purlins and rafters
upto 10 metres span and 5 metres height including stacking
the material within 50 metres lead:
Of sectional area 40 square centimetres and above. Cum 3395.25 3395.25
19.11 Dismantling steel work in built up sections in angles, tees, flats and
channels including all gusset plates, bolts, nuts, cutting rivets,
Kg 4.24 4.24
welding etc. including dismembering and stacking within 50metres
lead.
19.12 Dismantling tile work in floors and roofs laid in cement mortar
including stacking material within 50 metre lead.For thickness of Sqm 55.95 55.95
tiles above 10 mm and upto 25 mm
19.13 Demolishing brick tile covering in terracing including stacking
of serviceable material and disposal of unserviceable material Sqm 80.06 80.06
within 50 metres lead.
19.14.1 Dismantling roofing including ridges, hips valleys and gutters
etc., and stacking the material within 50 metres lead of:

G.S. Sheet Sqm 126.22 126.22
19.14.2 Dismantling roofing including ridges, hips valleys and gutters
etc., and stacking the material within 50 metres lead of: Sqm 59.15 59.15
Asbestos Sheet
19.15 Dismantling tiled roofing with battens boarding etc. complete
including stacking of serviceable material and disposal of Sqm 162.60 162.60
unserviceable material within 50 metres lead.
19.16 Demolishing thatch roofing including mats, bamboo, jaffari
etc. complete including stacking of serviceable material and Sqm 47.77 47.77
disposal of unserviceable material within 50 metres lead.
19.17 Dismantling wooden bailies in posts and struts including
Metre 17.44 17.44
stacking within 50 metres lead.
19.18 Dismantling and stacking within 50 metres lead, fencing posts
or struts including all earth work and dismantling of concrete Each 181.87 181.87
etc. in base of: ‘T’ or ‘L’ iron or pipe.
19.19 Dismantling and stacking within 50 metres lead, fencing posts
or struts including all earth work and dismantling of concrete Each 101.36 101.36
etc. in base of: R.C.C
19.20 Dismantling barbed wire or flexible wire rope in fencing
Kg 30.60 30.60
including making rolls and stacking within 50 metres lead.
19.21 Dismantling precast concrete or stone slabs in walls, partition
walls etc. including stacking within 50 metres:
Thickness above 40 mm upto 75 mm Sqm 334.82 334.82
19.22 Dismantling cement asbestos, Celotax or other hard board
ceiling or partition walls including stacking of serviceable
Sqm 42.89 42.89
materials and disposal of unserviceable materials within 50
metres lead.
19.23 Dismantling old plaster or skirting raking out joints and
cleaning the surface for plaster including disposal of rubbish to Sqm 41.75 41.75
the dumping ground within 50 metres lead.
19.24 Dismantling aluminium/ Gypsum partitions, doors,
windows, fixed glazing and false ceiling including disposal of
unserviceable surplus material and stacking of serviceable Sqm 42.9 42.9
material with in 50 meters lead as directed by Engineer-in-
charge.
19.25 Demolishing C.C. /R.C.C. work by mechanical means and
stockpiling at designated locations and disposal of dismantled
materials upto a lead of 1000m, stacking serviceable and Cum 2187.69 2187.69
unserviceable material separately including cutting
reinforcement bars.
19.26 Dismantling C.I. or asbestos rain water pipe with fittings and
clamps including stacking the material within 50 metres lead :

100 mm Metre 60.48 60.48
19.27 Dismantling C.I. or asbestos rain water pipe with fittings and
clamps including stacking the material within 50 metres lead :

150 mm Metre 62.21 62.21
19.28 Taking out doors, windows and clerestory window shutters
(steel or wood) and including resizing and refixing of shutters. Each 305.94 305.94
19.29. Dismantling G.I. pipes (external work) including excavation

and refilling trenches after taking out the pipes, manually / by
mechanical means including stacking of pipes within 50 metres
lead as per direction of Engineer-in-Charge:
19.29.1 15 mm to 40 mm nominal bore Metre 122.20 122.20
19.29.2 Above 40 mm nominal bore Metre 129.40 129.40
19.30 Dismantling of flushing cistern of all types (C.I/PVC/Vitrious
china) including stacking of useful materials near the site and
disposal of unservicable materials within 50 metres lead as per
direction of Engineer-in-Charge: Each 703.91 0
SH:- 20.MARBLE AND GRANITE WORK

Labour
Rate
20.1 Providing and fixing 18mm thick gang saw cut mirror polished
(premoulded and prepolished) machine cut for kitchen
platforms, vanity counters ,window sills , facias and similar
locations of required size of approved shade, colour and
texture laid over 20mm thick base cement mortar 1:4 (1 cement
: 4 metal sand) with joints treated with white cement, mixed
with matching pigment, epoxy touch ups, including rubbing,
curing moulding and polishing to edge to give high gloss
finish etc. complete at all levels.
20.1.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble.
Area of slab up to 0.50 sqm sqm 4225.84 2470.64
20.1.2 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble.
Area of slab over 0.50 sqm sqm 4330.59 2470.65
20.2 Providing and fixing 18mm thick gang saw cut mirror polished
20.2.1 Granite of any colour and shade
Area of slab up to 0.50 sqm sqm 6346.64 2470.64
20.2.2 Providing and fixing 18mm thick gang saw cut mirror polished
Granite of any colour and shade
Area of slab over 0.50 sqm sqm 6355.56 2470.65
20.3 Extra for providing edge moulding to 18mm thick marble
stone counters, Vanities etc. including machine polishing to
edge to give high gloss finish etc. complete as per design
approved by Engineer-in-Charge.
20.3.1 Marble work Metre 218.36 162.61
20.3 Extra for providing edge moulding to 18mm thick marble
stone counters, Vanities etc. including machine polishing to
edge to give high gloss finish etc. complete as per design
approved by Engineer-in-Charge.
20.3.2 Granite work. Metre 374.86 284.57
20.4 Extra for fixing marble /granite stone over and above
corresponding basic item, in facia and drops of width upto 150
Metre 485.45 401.51
mm with epoxy resin based adhesive including cleaning etc.
complete.
20.5 Extra for providing opening of required size & shape for wash
basins/ kitchen sink in kitchen platform, vanity counters and
similar location in marble/Granite/stone work including Each 2865.32 820.56
necessary holes for pillar taps etc. including rubbing and
polishing of cut edges etc. complete.
20.6 Mirror polishing on marble work/Granite work/stone work
sqm 402.16 348.45
where ever required to give high gloss finish complete.
20.7 Stone tile (polished) work for wall lining over 12mm thick bed
of cement mortar 1:3 (1 cement: 3metal sand) and cement
slurry @ 3.3 kg/sqm including pointing in white cement
complete.
20.7.1 8 mm thick.
Raj Nagar plain white marble/ Udaipur green marble/ Zebra
sqm 2981.38 2045.15
black marble.
20.7.2 8mm thick.Granite of any colour and shade. sqm 3663.30 2045.15
SH:-21 MISCLANIOUS ITEMS

Labour
Rate
21.1 Providing and fixing MDF board shelve with door shutters
including steel ( grade 304 )autocos hiinges with necessary sqm 2857.32 1107.92
screws etc. complete.
21.2 Providing and fixing steel handle ( 304 grade ) with necessary
each 185.84 8.13
screws
21.3 Finishing with Deluxe Multi surface paint system ( P.U Paint) for
interiors and exteriors using primer as per manufactures
specifications two or more coats applied on MDF Board surface sqm 542.59 229.40
@1.25ltr/10 sqm) over including priming coat of special primer
applied @ 0.75 ltr/10 sqm
21.4 Providing and fixing Flush door shutters confirming to IS:2202

(part.I) decorative type,teek wood planks construction frame
of first class teek wood with polished on both faces of
shutters
35 mm thick including ISI marked Stainless steel butt hinges
sqm 5995.49 844.73
with necessary screws
SH:-21 MISCLANIOUS ITEMS ( Road/helipad work)

21.5 Preparation and consolidation of sub grade with power road
roller of 8 to 12 tonne capacity after excavating earth to an
average of 22.5 cm. depth, dressing to camber and sqm 167.59 0.00
consolidating with road roller including making good the
undulations etc. and re-rolling the sub grade and disposal of
surplus earth lead upto 50 metres.
21.6 Providing and laying design mix cement concrete in roads, taxi
tracks and runways having a minimum works test beam
flexural strength of 30 kg. per cm2 at 28 days using not less
than 340 Kg. of cement per cum of finished concrete, coarse
sand and graded stone aggregate of 40mm nominal size in
appropriate proportions as per specified design criteria
approved by Engineer-in-charge,mechanically. vibrated using
needle and surface vibrators including steel form work with
sturdy M- S. channel sections including curing and providing cum 15400.40 3106.80
and filling construction joints and dummy joints with
approved joint filter Primer or equivalent including rounding
of the edges and filling the grooves 10x25mm deep at top for
construction joints and 10mmx50mm deep at top for dummy
joints with joint sealing compound (conforming to grade B of
IS : 1834) including making necessary arrangements for
expansion joints etc. all complete.
21.7 Providing and laying in position bitumen hot sealing

compound for expansion joints etc.Using grade 'A' sealing mtr 4.33 2.46
compound.
21.8 Painting runway/taxi track/apron marking with adequate no.
of coat to give uniform finish with road marking paint of
superior make as approved by the Engineer-in-charge sqm 225.82 102.41
including cleaning the surface of all dirt, scales, oil, grease and
other foreign material etc and lining out complete. New work
(Two or more coats)
21.9 Construction of granular sub base by providing close graded

Materials confirming to specifications, mixing in a mechanical
mix plant at OMC ,carriage of mixed materials by tippers to
work site for all leads & lifts spreading in uniform layaers of
specified thickness with motor grader on prepared surface and sqm 6970.15 253.38
compacting with vibrator power roller to achive the desired
density complete as per specifications and direction of
Engineer-in-charge. With materials confirming of grade.1 ( Size
range 75 mm to 0.075mm ) having CBR Value-30
21.10 Construction of dry learn cement concrete sub base over a

prepred sub grade with coarse and fine agregate confirming to
IS:383 ,the size of coarse agregate not exceeding 25 mm
,agregate cemnt ratio not to exceed 15:1 ,agregate gradation
after blending to be as per specifications, cement content not
less than 150 Kg/cum ,optimum moisture content to
determined during trail length construction ,concrete strength cum 9139.13 355.56
not less than 10 Mpa at 7 days ,mixed in batching plant
,transported to site for all leads and lift ,laid with a mechanical
paver ,compating with 8 to 10 tonne vibrator roller finishing
and curing etc.. complete as per the direction of Engineer-in-
charge

Schedule of Rates 2018 For Kalpeni W.E.F 01.11.2018

Uploaded by

Copyright:

Available Formats

Schedule of Rates 2018 For Kalpeni W.E.F 01.11.2018

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Schedule of Rates 2018 For Kalpeni W.E.F 01.11.2018

Uploaded by

Copyright:

Available Formats

1 afc91d2399f7e2e8d231dbea2d348e99

8 Bricks 1000 Nos 413.69 89.62

9 Brick Tiles, Allahabad 1000 Nos 258.56 56.01

SCHEDULE OF RATES 2018 AT KALPENI

48 Carriage of cement Mt 127.71

Factory made glass reinforced plastic door frame 90x45xmm

213 C.I.M.S brackets Each 97.33

264 Arcylic exterior paint litre 307.72

357 Metalic paint litre 1950.00

405 C.P. brass toilet holder of standard size each 325.00

SH:-1. MORTARS ( M Sand )

All kinds of soil. Cum 275.35 275.35

Ordinary rock Cum 531.75 531.75

2.8.1 Pipes, cables etc not exceeding 80 mm dia Mtr 249.50

3. SH :- PLAIN CEMENT CONCRETE ( M. Sand )

3.7.1 1:2:4 ( 1 cement: 2 coarse sand : 4 graded stone aggregate 20mm

SH:4. R.C.C WORK with M.sand

4.8.1 50mm thick Sqm 1673.64 953.77

4.10 Providing and fixing precast cement concrete 1:2:4 ( 1 cement: 2

SH:4.CENTERING & SHUTTERING

SH:- 5.BRICK WORK( with M. sand )

SH:-6.STONE WORK With M.Sand

7.4 Providing and fixing 30 mm thick panelled, glazed or panelled

7.11 Providing and fixing curtain rods of 1.25 mm thick chromium

7.26.2 Fixed to openings/wooden frames with rawl plugs screws etc

SH:-8. STEEL WORK

8.1 Structural steel work riveted, bolted or welded in built up

8.8 Providing and fixing stainless steel ( Grade304) railing made of

8.90 Steel work welded in built up section / framed work including

Providing and fixing pressed steel door frames confirming to IS:

SH:-9. FLOORING( with M.sand )

9.2 Cement plaster skirting (upto 30cm.height) with cement

9.4 Providing and fixing ceramic glazed floor tiles of size

9.6 Providing and laying vitrified (premium quality ) in diffren

9.7 Chequerred precast cement concrete tiles 22 mm thick in

9.14 Providing and laying vitrified tiles in diffrent sizes ( thickness to

Size of tiles 500x500 mm Sqm 2639.90 509.02

9.20 Providing and laying vitrified floor tiles (premium quality ) in

Size of tiles 600x600 mm Sqm 2791.22 509.02

Size of tiles 800x800 mm Sqm 2937.93 509.02

Size of tiles 1000x1000 mm Sqm 3066.52 509.02

Size of tiles 500x500 mm Sqm 2658.33 588.96

Size of tiles 600x600 mm Sqm 2808.33 588.96

Size of tiles 800x800 mm Sqm 2953.10 588.96

9.26 Providing and laying vitrified (premium quality ) in diffren sizes

Size of tiles 1000x1000 mm Sqm 3085.73 588.96

Labour Rate( Cement &M.sand issued by the department)

Sqm 1282.03 502.17

Sqm 1330.40 415.06

Size of tiles 500x500 mm Sqm 2060.89 415.06

Size of tiles 500x500 mm Sqm 2140.69 502.17

Size of tiles 500x500 mm Sqm 2399.77 461.52

L.7 Providing and laying vitrified floor tiles (premium quality ) in

Size of tiles 600x600 mm Sqm 2553.82 461.52

Size of tiles 800x800 mm Sqm 2700.53 461.52

Size of tiles 1000x1000 mm Sqm 2829.12 461.52

Size of tiles 500x500 mm Sqm 2502.54 560.25

Size of tiles 600x600 mm Sqm 2652.54 560.25

Size of tiles 800x800 mm Sqm 2797.31 560.25