Scribd
Upload
152 views3 pages

HW # 13 PDF

Sensors suitable for the applications include: (a) photoelectric sensor (b) ultrasonic sensor (c) inductive proximity sensor (d) inductive proximity sensor A diaphragm pressure sensor requires a diaphragm with one side open to the atmosphere to give a measure of the gauge pressure present in a system. The change in resistance of an electrical resistance strain gauge with a gauge factor of 2.0 and resistance 100 Ω when subject to a strain of 0.001 is 0.002 Ω.

Uploaded by

arshad gabary
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
152 views3 pages

HW # 13 PDF

Sensors suitable for the applications include: (a) photoelectric sensor (b) ultrasonic sensor (c) inductive proximity sensor (d) inductive proximity sensor A diaphragm pressure sensor requires a diaphragm with one side open to the atmosphere to give a measure of the gauge pressure present in a system. The change in resistance of an electrical resistance strain gauge with a gauge factor of 2.0 and resistance 100 Ω when subject to a strain of 0.001 is 0.002 Ω.

Uploaded by

arshad gabary
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

HW # 13

1-Select sensors that might be suitable for the following applications: (a) counting boxes
moving along a conveyor belt, (b) verifying the level of milk in a plastic bottle
moving along a conveyor belt, (c) determining when the piston in a cylinder has reached
a particular point in its extension; (d) determining when a metal plate has reached the
right position under a tool.

2- A diaphragm pressure sensor is required to give a measure of the gauge pressure present
in a system. Such a sensor will need to have a diaphragm with:
a. A vacuum on one side.
b. One side open to the atmosphere.
c. The pressure applied to both sides.
d. A controlled adjustable pressure applied to one side.

3- The change in resistance of an electrical resistance strain gauge with a gauge factor of 2.0
and resistance 100 O when subject to a strain of 0.001 is:
a. 0.0002 O b. 0.002 O c. 0.02 O d. 0.2 O

4-Problems 4A,and 4B refer to Figure shown below, which shows the symbol for a directional valve.
4A-Decide whether each of these statements is true (T) or false (F). The valves has:
(i) 4 ports (ii) 2 positions
A. (i) T (ii) T B. (i) T (ii) F C. (i) F (ii) T D. (i) F (ii) F
4B- Decide whether each of these statements is true (T) or false (F).
(i) When solenoid A is energized, the cylinder extends.
(ii) When solenoid B is energized, the cylinder extends.
A. (i) T (ii) T B. (i) T (ii) F C. (i) F (ii) T D. (i) F (ii) F

Fig # 4
5-Based on Fig # 5. Decide whether each of these statements is true (T) or false (F).

1- With Push button not pressed. Which option Best Describes the two statements?
(i) Pressure is applied to port 4. (ii) port2 is vented.
A (i) T (ii) T
B (i) T (ii) F
C (i) F (ii) T
D (i) F (ii) F
2-With Push button pressed. Which option Best Describes the two statements?
(i) Pressure is applied to port 4. (ii) Port 2 is vented.
A (i) T (ii)T
B (i)T (ii)F (vi)
C (i) F (ii) T (vii)
D (i) F (ii)F

Fig# 5

6- The Robot shown below is used in many automated factories. This robot picks up the work
piece being carried on conveyer A and places it on conveyer B. The operations sequences
are as follow:
i- When the start bottom is pressed, the robot rotate its arm clockwise
ii- When the robot arm has moved to the position of the work piece on conveyer A ,
arm grasp the work piece.
iii- When the arm has grasped the work piece, it rotates counterclockwise.
iv- When the arm has rotated to the position of conveyer B, it releases the work piece.
Design the pneumatic circuit for the above robot, Draw flow chart of the process

You might also like