KD318-MUI ADSL Router

NOTICE

This document contains proprietary information protected by copyright, and this Manual and all the
accompanying hardware, software, and documentation are copyrighted. All rights are reserved. No
part of this document may be photocopied or reproduced by mechanical, electronic, or other means
in any form.

The manufacturer does not warrant that the hardware will work properly in all environments and
applications, and makes no warranty or representation, either expressed or implied, with respect to
the quality, performance, merchantability, or fitness for a particular purpose of the software or
documentation. The manufacturer reserves the right to make changes to the hardware, software, and
documentation without obligation to notify any person or organization of the revision or change.

All brand and product names are the trademarks of their respective owners.

© Copyright 2004
All rights reserved.
 Content

1 Overview………………………...…………………………………..…………...…… 1

1.1 Features…………………………………...………………………………...……. 1

1.2 Packet Contents……………………..……………………………………...……. 2

1.3 System requirements……….…………………………………………...……….. 2

1.4 Factory Defaults………….…………………………………………...…………. 2

1.5 Warnings and Cautions…………………….……………………………...……. 3

2 Hard Description………………………………………………………………...…… 4

3 Software Description……………………………………………………………….… 5

4 Hardware Installation…………………………………………………………...…… 6

5 Routing Configuration Guide…………...……………………………………...…… 7

5.1 Local PC Configuration………………………………………..………...…… 7

5.2 Access the program………………………………………………...…………. 8

5.3 Edit PVC………………………………………………………...………...…... 8

5.4 Routing mode setting…………………………………..………………...…… 9

5.5 Reset Router…………………………………..………………...……………. 10

Appendix Frequent Asked Questions……………….……………………………...…... 12

ADSL ROUTER USER MANUAL

1 Overview

Thank you for using this ADSL router. Please read the manual carefully before you use it. This
ADSL router is an ADSL access device to support multiple line modes. It provides a
10/100BaseT interface for Ethernet connection at the user end. It receives adaptive rates up to
24Mbps downstream and transmits 1Mbps upstream. The ADSL Router is designed for quick,
intuitive and easy installation.

Two computers can simultaneously connect to the KE318MUI either via its USB, Switch, or
both ports to share its high-speed Internet access. You can connect to its Switch port regardless
of the operating system you are using, or connect to its USB port to allow easy installation to a
USB equipped computer.

1.1 Features

1.1.1 General
Max download speed: 24Mbps.
Max upstream speed: 1Mbps.

1.1.2 Standards & Protocols Conformance

ITU G.994 G.992.1(G.DMT) G.992.2(G.LITE) G.992.3
ITU G.992.3(G.DMT.BIS)
ITU G.992.5
T1.413
PPPoE
PPPoA
IPoA

1.1.3 Operating System Support

WINDOWS 98
WINDOWS 98 SE
WINDOWS ME
WINDOWS 2000
WINDOWS XP
LINUX

1.1.4 ATM Capabilities

ATM Connection
VPI Range: 0-255

1
ADSL ROUTER USER MANUAL

VCI Range: 32-65535

Auto-search PVC
AESA (E.164, DCC, ICD)
SVC&PVC Support
UNI 3.0 & 3.1 Signaling
Support AAL 5

1.1.5 Environmental
Operating humidity: 10%-90% non-condensing
Non-operating storage humidity: 5%-95% non-condensing

1.2 Packet Contents

The packet contents are as the following:

ADSL ROUTER x1
External Splitter x1
AC adapter x1
Telephone Line x1
Ethernet Cable x1
USB Cable x1
Cdisk x1

1.3 System Requirements

Before using this ROUTER, verify that you meet the following requirements:
Subscription for ADSL service. Your ADSL service provider should provide you
with at least one valid IP address (static assignment or dynamic assignment via
dial-up connection).
One or more computers, each contains an Ethernet 10/100M Base-T network
interface card (NIC).
A hub or switch, if you are connecting the device to more than one computer.
For system configuration using the supplied web-based program: A web browser
such as Internet Explorer v5.0 or later, or Netscape v4.7 or later.

1.4 Factory Defaults

The device is configured with the following factory defaults:

2
ADSL ROUTER USER MANUAL

IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Encapsulation: RFC2516 routing
VPI/VCI: According to local information

1.5 Warnings and Cautions

Never install telephone wiring during storm. Avoid using a telephone during an
electrical storm. There might be a risk of electric shock from lightening.
Do not install telephone jacks in wet locations and never use the product near
water.
To prevent dangerous overloading of the power circuit, be careful about the
designed maximum power load ratings. Not to follow the rating guideline could
result in a dangerous situation.
Please note that telephone line on router must adopt the primary line that directly
outputs from junction box. Do not connect router to extension phone. In addition,
if your house developer divides a telephone line to multi sockets inside the wall
of house, please only use the telephone that has connected with the splitter of
ADSL router when you access the Internet. Under the above condition, if you
also install telephone with anti-cheat-dial device, please pull out this kind of
telephone, otherwise ADSL router may occur frequently off-line.

3
ADSL ROUTER USER MANUAL

2 Hard Description

Front Panel

LED Color Function

On: Power
PWR Green
Off: No power
Strady: ADSL link established and active
DSL Green
Blinking: ADSL is trying to establish a connect
Blinking: ADSL data activity occurs.
ACT Green
Off: No ADSL data is being sent or received.

On: LAN link established and active

LAN1,2,3,4 Green Blinking: ADSL data activity occurs.
Off: No LAN link.

On: USB link established and active

USB Green
Off: No USB link

Rear Panel:

Port Function
Connects the device to an ADSL telephone jack or splitter using a RJ-11
DSL
telephone cable

Connects the device to your PC's Ethernet port, or to the uplink port on your
LAN1,2,3,4
hub/switch, using a RJ-45 cable

Reset System reset or reset to factory defaults.

PWR Connects to the supplied power adapter
Switches the unit on and off

4
ADSL ROUTER USER MANUAL

3 Software Installation

This chapter shows you how to install the router’s USB drivers when PC connects to the router
via its USB port.

1. Insert the rectangular end of a USB cable into the USB port of your PC.

2. Insert the square end of the USB cable into the USB port of the Router.

3. Power on the router and then a dialog box of “ A new hardware is found” is displayed on
the screen.
4. Press “Next” button, the system then search for hardware driving program. Choose the
soft driver in the “assigned position” and press “next”, the system will automatically
install the driving program recorded on the soft disk into the system.

5
 ADSL ROUTER USER MANUAL

4 Hardware Installation

This chapter shows you how to connect router. Meanwhile, it introduces the appropriate
environment for the router and installation instructions.

4.1 Ethernet connection

1. Using a telephone line to connect the DSL port of ROUTER to the ROUTER port of the
splitter, and using a other telephone line connect your telephone to the PHONE port of
the splitter, then connect the wall phone jack to the LINE port of the splitter.
The splitter comes with three connectors as below:
LINE: Connects to a wall phone jack (RJ-11 jack)
ROUTER: Connects to the DSL jack of ROUTER
PHONE: Connects to a telephone set

2. Using an Ethernet Cable to connect the LAN port of the ROUTER to your LAN or a PC
with network card installed.

3. Connect the power cable to the PWR connector on ROUTER, then plug in the AC power
adapter to the AC power outlet, and then press the on-off button.

4.2 USB connection

1. Insert the rectangular end of a USB cable into the USB port of your PC.

2. Insert the square end of the USB cable into the USB port of the Router.

6
ADSL ROUTER USER MANUAL

5 Routing Configuration Guide

5.1 Local PC Configuration

5.1.1 Windows 95, 98, ME, XP

1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click
“Control Panel”.
2. Double-click the “Network” icon.
3. On the “Configuration” tab, select the TCP/IP network associated with your network
card and then click “Properties”.
4. In the “TCP/IP Properties” dialog box, click the “IP Address” tab. Set the IP address
as 192.168.1.x (x can be a decimal number from 2 to 254.) like 192.168.1.2, and the
subnet mask as 255.255.255.0.
5. On the “Gateway” tab, set a new gateway as 192.168.1.1, and then click “Add”.
6. Configure the “DNS” tab if necessary. For information on the IP address of the DNS
server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.
8. You will be prompted to restart Windows. Click “Yes”.

5.1.2 Windows 2000

1. In the Windows task bar, click the “Start” button, point to “Settings”, and then click
“Control Panel”.
2. Double-click the “Network and Dial-up Connections” icon.
3. In the “Network and Dial-up Connections” window, right-click the “Local Area
Connection” icon, and then select “Properties”.
4. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
5. In the “Internet Protocol (TCP/IP) Properties” dialog box, set the IP address as
192.168.1.x (x can be a decimal number from 2 to 254.), and the subnet mask as
255.255.255.0 and the default gateway as 192.168.1.1. Then click “OK”.
6. Configure the “DNS” tab if necessary. For information on the IP address of the DNS
server, please consult with your ISP.
7. Click “OK” twice to confirm and save your changes.

7
 ADSL ROUTER USER MANUAL

5.2 Access the program

After configuring the IP Address of you computer, powering on the ADSL Router, and
launching a web browser, such as Internet Explorer, use http://192.168.1.1 to log on to setting page.

Enter username ‘admin’

and password ‘adslroot’

Click OK

Attention: the username and password are both lowercase.

All the parameters shown in this page are the factory default settings.

5.3 Edit PVC

1. Click“Device info WAN” to check whether the pre-defined PVC values contain the
value you need.

2. If not, please select from “Advanced Setup WAN” and click “Edit” button.

8
ADSL ROUTER USER MANUAL

3. Please enter the VPI/VCI value you want, and continue clicking the“Next”button till the
confirmation page displays.

4. Click the“Save”button in the summarize page to save the settings..

5. Select from“Management Save/Reboot” and then click the “Reboot” button to restart
the ROUTER.

5.4 Routing mode setting

1. Click“Device Info WAN” and check whether there is VPI/VCI value provided by
operator.
2. If not, please operate according to steps “4.3 Editing PVC”till the instructions shown in
the figure display.

Select“PPP over Ethernet ( PPPoE )”in Connection Type and “LLC/SNAP-BRIDGING”

9
ADSL ROUTER USER MANUAL

in Encapsulation Mode and then click“Next”.

3. Enter user name and password provided by operator, then click“Next”.

4. Click“Next”in the following page.

5. Click the“Save”button in the summarize page to save the settings.

6. Select from“Management Save/Reboot”and then click the“Reboot”button to restart the
ROUTER.
7. If factory default settings of ROUTER includes VPI/VCI provided by operator, please
select from“Advanced Setup WAN” and find corresponding VPI/VCI value in the page
and click the“Edit”button. Then follow the steps as specified above.
8. After routing settings are finished, if you want to enable DHCP service, then please set IP
address of PC network card to obtain an IP address automatically. If you don’t want to
enable DHCP service, then you need to assign an IP address for your PC network card and
set DNS address to the address provided by operator (If operator doesn’t provide the DNS
address, then the address is set to 192.168.1.1 that is the address of ROUTER).

Note: If you want to cancel all modification that you do on the router, please select from
“Management Setting Restore Default Settings” to restore factory default settings.

5.5 Reset Router

For convenience: shutdown your computer first.

1. Switch the ADSL router OFF.

10
ADSL ROUTER USER MANUAL

2. On the Rear Panel of the ADSL router you will find a small hole with the word "reset"
written below it. It's just big enough for a ball-point tip. Insert a ball-point tip into this little
hole (actually it's a reset switch) and keep the ball-point tip in there.
3. Switch the router ON, and hold the ball-point tip in the little hole.

You can release the ball-point after about 10 seconds. You have then completed the full-reset.
Your ADSL router will now have its factory default settings. IP address will be 192.168.1.1 and
the subnet mask will be 255.255.255.0.

Now you can reboot your PC again.

11
 ADSL ROUTER USER MANUAL

Appendix Frequent Asked Questions

Q: None of the LEDs are on when you power on the ADSL router?
A: Please make sure what you use is the power adaptor attached with the router package，and check the
connection between the AC power and ADSL router.

Q: DSL LED does not turn on after connect telephone line?

A: Please make sure what you use is the standard telephone line (as attached with the package), make
sure the line is connected correctly and check whether there is poor contact at each interface. Wait
for 30 seconds to allow the router establishes connection with you ADSL operator.

Q: DSL LED is in the circulation of slow-flashing and fast-flashing after connect telephone line?
A: This situation means the router is in the status of failing to establish connection with Central Office.
Please check carefully and confirm whether the router has been installed correctly.

Q: LAN LED does not turn on after connect Ethernet cable?

A: Please make sure Ethernet cable is connected hub/PC and router correctly. Then please make sure
the PC/hub have been power on.
Please make sure that you use parallel network cable to connect UpLink port of hub, or use parallel
network cable to connect PC. If connect normal port of hub (not UpLink port), you must use
cross-cable. Please make sure that your network cables meet the networking requirements above.

Q: PC cannot access the Internet?

A: First check whether PC can ping the interface Ethernet IP address of this product successfully
(default value is 192.168.1.1) by using ping application. If ping application fails, please check the
connection of Ethernet cable and check whether the states of LEDs are in gear.
If the PC uses private IP address that is set manually (non-registered legal IP address), please check:
1. Whether IP address of the PC gateway is legal IP address. Otherwise please use the right
gateway, or set the PC to Obtain an IP address automatically.
2. Please confirm the validity of DNS server appointed to the PC with ADSL operator. Otherwise
please use the right DNS, or set the PC to Obtain an IP address automatically.
3. Please make sure you have set the NAT rules and convert private IP address to legal IP address.
IP address range of the PC that you specify should meet the setting range in NAT rules.
Central Office equipment may have problem.

Q: PC cannot browse Internet web page?

A: Please make sure DNS server appointed to the PC is correct. You can use ping application program
to test whether the PC can connect to the DNS server of the ADSL operator.

Q: Initialization of the PVC connection failed?

A: Be sure that cable is connected properly from the DSL port to the wall jack. The DSL LED on the
front panel of the ADSL router should be on. Check that your VPI, VCI, type of encapsulation and
type of multiplexing setting are the same as what you collected from your service provider,
Re-configure ADSL router and reboot it. If you still can not work it out, you may need to verify
these variables with the service provider.

If the cause is not above given，please contact your local service provider

12