Atmospheric Distillation Unit

Unit 5. Crude oil distillation. Lecture.
Atmospheric Distillation Unit
Figure 1 – Typical PFD for an Atmospheric Distillation Unit

Crude oil is sent to the Atmospheric distillation unit after desalting and
heating.
The purpose of atmospheric distillation is primary separation of various
«cuts» of hydrocarbons namely, fuel gases, LPG, naphtha, kerosene, diesel and
fuel oil.
The heavy hydrocarbon residue left at the bottom of the atmospheric
distillation column is sent to vacuum distillation column for further separation of
hydrocarbons under reduced pressure.
As the name suggests, the pressure profile in atmospheric distillation unit is
close to the atmospheric pressure with highest pressure at the bottom stage which
gradually drops down till the top stage of the column.
The temperature is highest at the bottom of the column which is constantly
fed with heat from bottoms reboiler.
The reboiler vaporizes part of the bottom outlet from the column and this
vapor is recycled back to the distillation column and travels to the top stage
absorbing lighter hydrocarbons from the counter current crude oil flow.
The temperature at the top of the column is the lowest as the heat at this stage
of the column is absorbed by a condenser which condenses a fraction of the
vapors from column overhead.
The condensed hydrocarbon liquid is recycled back to the column. This
condensed liquid flows down through the series of column trays, flowing counter
current to the hot vapors coming from bottom and condensing some of those
vapors along the way.
Thus a reboiler at the bottom and a condenser at the top along with a number
of trays in between help to create temperature and pressure gradients along the
stages of the column.
The gradual variation of temperature and pressure from one stage to another
and considerable residence time for vapors and liquid at a tray help to create near
equilibrium conditions at each tray.
So ideally we can have a number of different vapor-liquid equilibria at
different stages of this column with varying temperature and pressure conditions.
This means that the hydrocarbon composition also varies for different trays with
the variation in temperature and pressure.
The heaviest hydrocarbons are taken out as liquid flow from the partial
reboiler at bottom and the lightest hydrocarbons are taken out from the partial
condenser at the column overhead.
Various other cuts of hydrocarbons are taken out as side draws from different
stages of the column. Starting from LPG at the top stages, naphtha, kerosene,
diesel and gas oil cuts are taken out as we move down the stages of atmospheric
column.
The heaviest hydrocarbon residue taken out from partial reboiler is sent to the
Vacuum distillation column for further separation under reduced pressure.
Vacuum Distillation Unit
Figure 1 – Typical PFD of a Vacuum Distillation Unit

Heavies from the Atmospheric distillation column are heated to
approximately 400˚C in a fired heater and fed to the Vacuum distillation column
where they are fractionated into light vacuum gas oil (LVGO), heavy vacuum
gas oil (HVGO) and vacuum residue.
Some heavy hydrocarbons cannot be boiled at the operating temperature and
pressure conditions in the atmospheric distillation column. Hence they exit the
bottom of the column in liquid state and are sent to the vacuum distillation column
where they can be boiled at a lower temperature when pressure is significantly
reduced.
Absolute operating pressure in a vacuum tower can be reduced to 20 mm of
Hg or less (atmospheric pressure is 760 mm Hg).
In addition, superheated steam is injected with the feed and in the tower
bottom to reduce hydrocarbon partial pressure to 10 mm Hg or less. Lower partial
pressure of the hydrocarbons makes it even easier for them to be vaporized, thus
consuming less heat energy for the process.
Steam ejectors can be used to suck the lighter hydrocarbon vapors at low
pressure from the top of the column. These vapors are then cooled down to
condense the steam which had been introduced in the column earlier. The
condensed oily water is removed and can be recycled to the column after boiling
it. Hydrocarbon vapors are taken out at this stage.
Two different cuts of hydrocarbons – «light vacuum gas oil» and «heavy
vacuum gas oil» are separated in the vacuum distillation column at different stages
of the column, based on the difference between their boiling point ranges.
The liquid being drawn at low pressure needs to be pumped. Then it is heated
and partially recycled back to the column.
Light vacuum gas Oil is sent to a hydrotreater and then to a catalytic
cracking unit to obtain smaller chain hydrocarbons. Heavy vacuum gas oil is also
sent for cracking using hydrogen in a hydrocracking unit to produce smaller
chain hydrocarbons.
Heavy hydrocarbons which cannot be boiled even under reduced pressure
remain at the bottom of the column and are pumped out as vacuum residue. The
vacuum distillation column bottom residue can only be used for producing coke in
a coker unit or to produce bitumen.

Atmospheric Distillation Unit

Uploaded by

Copyright:

Available Formats

Atmospheric Distillation Unit

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Atmospheric Distillation Unit

Uploaded by

Copyright:

Available Formats

Unit 5. Crude oil distillation. Lecture.

Atmospheric Distillation Unit

Figure 1 – Typical PFD for an Atmospheric Distillation Unit

Figure 1 – Typical PFD of a Vacuum Distillation Unit

You might also like