ET-KA7500

SWITCHMODE Pulse Width Modulation Control Circuit

The KA7500 is a fixed frequency, pulse width modu lation control circuit designed primarily
for SWITCHMODE power supply control.

• Complete Pulse Width Modulation Control Circuitry N SUFFIX

PLASTIC
• On– Chip Oscillator with Master or Slave Operation
• On– Chip Error Amplifiers
• On– Chip 5.0 V Reference 16
• Adjustable Deadtime Control 1
• Uncommitted Output Transistors Rated to 500 mA Source or
Sink
• Output Control for Push– Pull or Single– Ended Operation
• Undervoltage Lockout

ORDERING INFORMATION
KA 7500 Plastic
KA 7500 Chip

TA = - 20° to +85°C

LOGIC DIAGRAM
PIN ASSIGNMENT
5 6 13
output control noninv. input 1 16 noninv. input
dead time control inv. input 2 15 inv. input
oscillator
4
feedback 3 14 ref. output
pulce steering flip
KA
error amp 1
flop dead time control 7500 output control
1
2
PWM comparator
&
8
CT 5 12 Vcc
T 9

error amp 2 reference

11 RT 6 11 collector 2
16 regulator 10
gnd 7 10 emitter 2
15
collector 1 8 9 emitter 1
3 7 12 14

Pin 7 = GND
Pin 12 = Vcc

BEIJING ESTEK ELECTRONICS CO.,LTD

1
 ET-KA7500
MAXIMUM AND RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Recommended Maximum ratings Unit
operating
conditions
Min Max Min Max
VCC Supply Voltage 7 40 41 V
VI Amplifier Input Voltage -0.3 VCC-2 VCC+0.3 V
VO Collector Output Voltage 40 41 V
IOC Collector Output Current 200 250 mA
(Each Transistor)
T Storage Temperature Range -65 150 °C
T Operating Free-Air Temperature -20 85 °C
Range

ELECTRICAL CHARACTERISTICS (TA= -20 …+85°C, f =10kHz)

Symbol Parameter Test Conditions Value Tempe- Unit
Min Max rature,°
C
Vref Output voltage I0=1.0mA 4.75 5.25 -20…+85 V
VCC=15V
Uregin Input regulation VCC=7… 40V - 25 25 mV
I0=1.0mA
Uregout Output regulation I0=1… 10 mA - 15 25 mV
VCC =15V
ΔVref Output voltage I0=1mA - 1.0 -20…+85 %
change with VCC =15V
temperature
ISC Short circuit output
Vref=0 - 50 mA
current tsc< 1s
VCC=15 V
fosc Frequency C=0.01μF, R=12kΩ 6.0 14 kHz
VCC=15V
V(03)=0.7V
σfosc Standard Deviation VCC=15V - 15 %
of Frequency * V(03)=0.7V
σfosc(ΔV) Frequency Change VCC=7…40 V - 10 25 %
with Voltage V(03)=0.7V
σfosc(ΔТ) Frequency Change C=0.01μF, RT=12kΩ - 2.0 -20…+85 %
with Temperature VCC=15V
V(03)=0.7V
IIB(2T) Input bias current VI=0…5.25V - -10 μA
(pin 4) VCC=15V
V(03)=0.7V
DCmax Maximum duty cycle VI(04)=0V 45 - %
(each output) VCC=15V
V(03)=0.7V
VTHD1 Input threshold DCmax=0 - 3,3 V
voltage (pin 4) VCC=15V
(Zero Duty Cycle) V(03)=0.7V

BEIJING ESTEK ELECTRONICS CO.,LTD

2
 ET-KA7500

VTHD2 Input threshold Dcmax 0 - V

voltage (pin 4) VCC=15V
(Maximum Duty V(03)=0.7V
Cycle)

Symbol Parameter Test Conditions Value Tempe- Unit

Min Max rature,°
C
trc Output voltage rise VCC=15V - 200 -20…+85 ns
time (Common- V(03)=2.0V
Emitter)
tfc Output voltage fall VCC=15V - 100 ns
time (Common- V(03)=2.0V
Emitter)
trf Output voltage rise VCC=VC=15V - 200 ns
time (Emitter- V(03)=2.0V
Follower)
tff Output voltage fall VCC=VC=15V - 100 -20…+85 ns
time (Emitter- V(03)=2.0V
Follower)
VTHP Input threshold DCmax=0 - 4.5 V
voltage (pin 3) VCC=15V
II Input sink current VCC=15V 0.3 - mA
(pin 3) V(03)=0.7V
VIO Input offset voltage VCC=15V - 10 mV
VO(03)=2.5V
IIO Input offset current VCC=15V - 250 nA
VO(03)=2.5V
IIB Input bias current VCC=15V - 1 μA
VO(03)=2.5V
VICRL Low Input common VCC=7…40V -0.3 - V
mode voltage range
VICRH High Input common VCC=7…40V VCC -2 - V
mode voltage range
AVOL Open loop voltage ΔV0=3V 70 - dB
amplification VCC=15V
VO=0.5…3.5V
fb Unity-gain VCC=15V 100 - kHz
bandwidth
CMRR Common mode Vcc=40V 65 - 25 dB
rejection ratio
IOL Output sink current VCC=15V 0.3 - -20…+85 mA
(pin 3) V0(03)=0.7V

IOH Output source VCC=15V -2.0 mA

current (pin 3) V0(03)=3.5V

IC(off) Collector off-state VCE=VCC=40V - 100 μA

current

BEIJING ESTEK ELECTRONICS CO.,LTD

3
 ET- KA7500

IE(off) Emitter off-state VCC=VC=40V - -100 μA

current VE=0V
VSAT(C) Collector - Emitter VCC=15V - 1.3 V
saturation voltage VE=0V
(Common-Emitter) V0(03)=3.0V
IC=200mA
VSAT(E) Collector - Emitter VCC=VC=15V - 2.5 25 V
saturation voltage -- 200mA
IE=-
2.9 -20…+85
(Emitter-follower) V0(03)=3.0V

IOCH Output control input VCC=15V - 3.5 25 mA

current V0(03)=0.7V

ICC15 Standby Supply VCC=15V - 10 mA

Current at VCC 15V

.
Symbol Parameter Test Conditions Value Tempe- Unit
Min Max rature,°
C
ICC40 Standby Supply VCС=40V - 15 25 mA
Current at VCC 40V
ICCA Average Supply VCC=15V - 17 -20…+85 mA
Current V0(03)=0.7V
V0(04)=2.0V

Standard deviation is a measure of the statistical distribution about the mean as derived from the formula
N

∑ ( Xn − X )
n =1
2

σ=
N −1

4 BEIJING ESTEK ELECTRONICS CO.,LTD