All statements without guarantee

perete exterior Exterior wall

created on 3.5.2020

Thermal protection Moisture proofing Heat protection

No condensate Temperature amplitude damping: >100
U = 0,16 W/(m²K) phase shift: non relevant
Thermal capacity inside: 112 kJ/m²K
EnEV Bestand*: U<0,24 W/(m²K)

excellent insufficient excellent insufficient excellent insufficient

outside
5 4

140 3
400

250 www.ubakus.de
2

Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
5 1
inside
1 FINISAJ INTERIOR (5 mm) 3 VATA MINERALA BAZALTICA (140 mm)
2 BCA (250 mm) 4 FINISAJ EXTERIOR (5 mm)

Impact of each layer and comparison to reference values

For the following figure, the thermal resistances of the individual layers were converted in millimeters insulation. The scale
refers to an insulation of thermal conductivity 0,035 W/mK.

Equivalent
insulation thickness
BCA VATA MINERALA BAZALTICA (WLS 035)

0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 mm
8 i
0 95 eT
u
ba =0,2 d
5
=0
,1
41 O ig u U
DI
N tzV dr Ne U tan au ,2 s
ch
u nie 4 s eub U=0 ,15 au
es nd E V1 B e N V n . U =0 siv
h
m sta En EV 16 nM aß s 40 s
är Be En nEV ESa elm 5 Hau fW Pa
W 5 - K
V E z er
En
E Ein fW BW -Lit bau
f W u K eG 3 u
K a Ne
e ub ärm
N EW

Inside air : 20,0°C / 50% Thickness: 40,0 cm

Outside air: -15,0°C / 70% sd-value: 1,5 m Weight: 153 kg/m²
Surface temperature.: 18,6°C / -14,8°C Heat capacity: 152 kJ/m²K

*Comparison to the maximum U-value according to the german EnEV 2014/2016 for first-time installation or renewal of Außenwänden (Anlage 3, Page 1
Tabelle 1, Zeile 1).
 All statements without guarantee

perete exterior, U=0,16 W/(m²K)

Temperature profile
Temperature profile
20 Temperature
1 2 3 4 Dew point
15

10 1 FINISAJ INTERIOR (5 mm)

Temperature [°C]

5 2 BCA (250 mm)

3 VATA MINERALA BAZALTICA (140 mm)
0 4 FINISAJ EXTERIOR (5 mm)
-5

-10

-15

0 50 100 150 200 250 300 350 400

Inside 0°C [mm]

Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
www.ubakus.de Outside

Temperature and dew-point temperature in the component. The dew-point indicates the temperature, at which water vapour
condensates. As long as the temperature of the component is everywhere above the dew-point temperature, no
condensation occurs. If the curves have contact, condensation occurs at the corresponding position.

Layers (from inside to outside)

# Material λ R Temperatur [°C] Weight
[W/mK] [m²K/W] min max [kg/m²]
Thermal contact resistance* 0,130 18,6 20,0
1 0,5 cm FINISAJ INTERIOR 0,870 0,006 18,6 18,6 7,0
2 25 cm BCA 0,120 2,083 7,2 18,6 125,0
3 14 cm VATA MINERALA BAZALTICA 0,035 4,000 -14,7 7,2 14,0
4 0,5 cm FINISAJ EXTERIOR 0,870 0,006 -14,8 -14,7 7,0
Thermal contact resistance* 0,040 -15,0 -14,8
40 cm Whole component 6,265 153,0
*Thermal contact resistances according to DIN 6946 for the U-value calculation. Rsi=0,25 and Rse=0,04 according to DIN
4108-3 were used for moisture proofing and temperature profile.

Surface temperature inside (min / average / max): 18,6°C 18,6°C 18,6°C

Surface temperature outside (min / average / max): -14,8°C -14,8°C -14,8°C

Page 2
 All statements without guarantee

perete exterior, U=0,16 W/(m²K)

Moisture proofing
For the calculation of the amount of condensation water, the component was exposed to the following constant climate for
90 days: inside: 20°C und 50% Humidity; outside: -15°C und 70% Humidity (Climate according to user input).
This component is free of condensate under the given climate conditions.

# Material sd-value Condensate Weight

[m] [kg/m²] [Gew.-%] [kg/m²]
1 0,5 cm FINISAJ INTERIOR 0,05 - 7,0
2 25 cm BCA 1,25 - 125,0
3 14 cm VATA MINERALA BAZALTICA 0,14 - 14,0
4 0,5 cm FINISAJ EXTERIOR 0,05 - 7,0
40 cm Whole component 1,49 153,0

Humidity
The temperature of the inside surface is 18,6 °C leading to a relative humidity on the surface of 55%.Mould formation is not
expected under these conditions.

Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
The following figure shows the relative humidity inside the component.

100 Relative humidity (%)

1 2 3 4 saturation point
90
80
Relative humidity (%)

1 FINISAJ INTERIOR (5 mm)

70
2 BCA (250 mm)
60
3 VATA MINERALA BAZALTICA (140 mm)
50 4 FINISAJ EXTERIOR (5 mm)
40
30
20
10
0
0 50 100 150 200 250 300 350 400
Inside 0°C [mm]
www.ubakus.de Outside
Notes: Calculation using the Ubakus 2D-FE method. Convection and the capillarity of the building materials
were not considered. The drying time may take longer under unfavorable conditions (shading, damp / cool
summers) than calculated here.

Page 3
 All statements without guarantee

perete exterior, U=0,16 W/(m²K)

Heat protection
The following results are properties of the tested component alone and do not make any statement about the heat protection
of the entire room:

Temperature profile
This document has been generated by the U-value calculator on www.ubakus.de. If you are harmed by the free use of these contents, the service provider is only liable in case of

36 Temperature at 3pm, 11am and 7am

34 1 2 3 4 Temperature at 7pm, 11pm and 3am
intent and gross negligence on the part of the service provider. For further information, please refer to the terms and conditions at https://www.ubakus.de/agb

32
30 1 FINISAJ INTERIOR (5 mm)
Temperature [°C]

28 2 BCA (250 mm)

26 3 VATA MINERALA BAZALTICA (140 mm)
24 4 FINISAJ EXTERIOR (5 mm)
22
20
18

Commercial use only with Plus-, PDF- or Profi-Option (from 2.99 € / month plus VAT).
16
14
0 50 100 150 200 250 300 350 400
Inside [mm]
www.ubakus.de Outside

[°C] The surface temperature during the day

36 Outside
34 Inside
32
30
28
26
24
22
20
18
16
14 Phase shift: 17.3h
12 14 16 18 20 22 24 2 4 6 8 10 12
[time of day]
Top:Temperature profile within the component at different times. From top to bottom, brown lines: at 3 pm, 11 am and 7 am
and red lines at 7 pm , 11 pm and 3 am.
Bottom:Temperature on the outer ( red ) and inner ( blue ) surface in the course of a day. The arrows indicate the location of
the temperature maximum values . The maximum of the inner surface temperature should preferably occur during the
second half of the night.

Phase shift* non relevant Heat storage capacity (whole component): 152 kJ/m²K
Amplitude attenuation ** >100 Thermal capacity of inner layers: 112 kJ/m²K
TAV *** 0,007
* The phase shift is the time in hours after which the temperature peak of the afternoon reaches the component interior.
** The amplitude attenuation describes the attenuation of the temperature wave when passing through the component. A value of 10
means that the temperature on the outside varies 10x stronger than on the inside, e.g. outside 15-35 °C, inside 24-26 °C.
*** The temperature amplitude ratio TAV is the reciprocal of the attenuation: TAV = 1 / amplitude attenuation
Note: The heat protection of a room is influenced by several factors, but essentially by the direct solar radiation through windows and the
total amount of heat storage capacity (including floor, interior walls and furniture). A single component usually has only a very small
influence on the heat protection of the room.

Page 4

Powered by TCPDF (www.tcpdf.org)