Hoover Fridge HVBF5172

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

COMBINED AND FROST FREE COMBINED EN

COMBINED AND FROST FREE COMBINED


CONTROL PANEL
(figure 1) The thermostat box to control the appliance is located inside the fridge compartment
on the top right. To check whether the appliance is functioning, make sure that the
thermostat knob is not set on "0“. Adjust the knob according to the desired temperature
in the fridge.

In this product the freezer compartment is automatically defrosted.


A small amount of frost or drops of water on the back of the fridge compartment when
the fridge is working is normal.

Make sure the water outlet is always clean. Make sure foods do not touch the back or
sides of the fridge compartment

Important: If the room temperature is very warm, the appliance may work
continuously and a layer of frost will deposit on the back of the fridge
compartment. In this case, turn the knob to lower settings.

FREEZING OF THE FREEZER COMPARTMENT


Place the foods to be frozen in the drawer. At the start of the freezing process, so as not to make the fridge compartment excessively cold, it may
be necessary to turn the thermostat knob back, according to the load and room temperature. Once the freezing process is completed, return the
thermostat knob to the usual value. The rating plate states the maximum quantity of foods that can be frozen, (see figure 2).

DEFROSTING OF THE FREEZER COMPARTMENT


(figure 2)
In case of a fridge with FROST FREE technology, the freezer compartment does not need to be defrosted
because this product is equipped with an automatic system which prevents ice from forming;

In case of a version without FROST FREE technology, it is recommended to manually defrost the
product when the layer of frost is more than 3 mm thick, by setting the knob on "0". Open the door and
remove the foodstuffs, making sure to store them in a cool place. Leave the door open as long as is
necessary for the layer of frost to melt. Dry the inside of the freezer with a sponge/cloth. Reposition the
foodstuffs and reset the knob to the usual values.

N.B.: This is the rating plate. If you need to contact our Service Department in the event of faults,
remember to give them the information on the plate.

N.B.: For better air circulation, leave some room between the foodstuffs.
N.B.: To TEST consumption and preservation standards,
In case of models with FROST FREE technology, avoid obstructing the
remove all drawers except for the bottom one.
cooling air vents.

REVERSING THE OPENING OF THE DOORS


Place the appliance on the floor or at a 45° angle, since it is necessary to work on the bottom of the appliance.
Remove the bottom hinge by loosening the Remove the middle hinge by loosening the Remove the bushes on the right-hand side
screws, then remove the lower door. screws, then remove the top door. of the doors and mount them back on the
left-hand side.

Remove the top hinge by loosening the Disassemble and move the corner guide from Remount the hinges and doors working from
screws. Unscrew the pin from the hinge. left to the right-hand side, turning it 180°. bottom to top, 1 - 2 - 3. Also remount the spacer
A- Unhook the washers between door and hinge.
cap by making
leverage
B- Remove the
screw
C- Remove the
corner guard

While fixing the top hinge on the left-hand In order to reverse the vertical handles, if Unscrew the handles from the left-hand side
side, tighten the screws and screw the pin any, remove the outer caps from the right- and move them to the right-hand side, then
back on in the left hole. hand side of the doors. position the outer caps removed previously
from the right-hand side to the left-hand side.
8
9

Put the appliance back in an upright position and wait two hours before turning it on.
N.B. For the doors to be correctly aligned, it is necessary to operate on the middle hinge.
Z STUDIO > 07-2009 – Cod. 41032400

You might also like